Posiflex | LM-6100/ LM-6600 | User manual | Posiflex LM-6100/ LM-6600 User Manual

Posiflex LM-6100/ LM-6600 User Manual
LM6100/LM6600
Series
LCD Monitor
USER’S MANUAL
Rev. : B
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions manual, may cause interference to radio communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians.
The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the
instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard
caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the LCD Monitor LM6100 and LM6600 series. These series provide versatile font
formats and support various instruction sets. These series of products receive instructions in serial communication
protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial
device if properly configured.
The manufacturer of the LM6100 and LM6600 series heartily apologizes to the user for reserving the right to change or
to modify this manual without notice due to the rapid and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com.tw,
http: //www.posiflexuk.com, http://www.posiflexusa.com.
TRADE MARKS AND SERVICE MARKS
All brand and product names and trademarks are the property of their respective holders.
© Copyright Posiflex Technology, Inc. 2010
I.
FEATURES
• Light weight and high luminance LCD monitor for industrial and
commercial use as well as application covers POS, POIS (Kiosk),
Factory Automation etc.
• High quality 12.1” TFT LCD panel with scaling up function for full
screen display
• Resolution: 1024 x 768
P/N: 19050904010
1
•
•
•
•
Tilt and swivel adjustable construction for LM-6101A series
Easy maintenance structure allowing easy cleaning
Wall mount bracket with 75mm VESA standard.
LM-6601A is a 12.1” LCD monitor with tilt adjust for 2nd display
attached to FT series POS system
• Support VGA interface and powered through interface cable for LM6601A
II. MODEL NUMBERS
LM6112A: 12.1” LCD Monitor w/ stand
LM6101A: 12.1” LCD Monitor w/ joining mechanism for Posiflex touch
terminals such as TP-8000/TP-8300 series
LM6112A
LM6101A on back
of TP-8000/TP-8300
LM6601A: 12.1” LCD Monitor w/ joining mechanism for Posiflex touch
terminals such as FT series
2
III. INSTALLATION
LM-6100 series
Base Mount and Stand along
1. Match the bottom of the panel unit into the monitor stand (for LM6112A) or
joining mechanism (for LM6101A).
2. Screw on the pivot screw for LM6112A. Screw on the pivot screw through a
split washer and then through a plain washer for LM6101A.
LM6112A
Pivot Screw
LM6101A
3. Fix LM6101A to the Posiflex TP-8000/TP-8300 terminal per instruction of
the terminal.
4. For LM6112A, connect the end of VGA cable with the power connector to
the back of the panel unit. For LM6101A, please arrange the power to be
supplied through the interface cable from the main unit and just connect the
video interface cable. Connect the other end of VGA cable to the appropriate
VGA port. LM6101A’s power is controlled by system.
Power Connector in VGA Cable
for LM6112A
VGA Connector
Power Connector from Power Adaptor
3
5. Adjust for best viewing tilt angle and engage the on screen display (OSD)
adjustment for best display effect whenever necessary. The monitor will sign
for “No Signal” status and go into power saving mode in 5 seconds when
there is no video signal. The display will come back when the signal does.
VESA Mount (75 mm VESA standard)
1. Please use the four screws which are
attached with wall mount bracket to
rotate into these four screws holes
which are in the back of monitor as “A”
in the right picture.
A
Note: Please DO NOT fasten these screws to the end at first time
rotates. The best way is rotate about 2-3 circles.
2. Take the bracket and aim the
four matching holes to these
four rotated screws. Then push
the bracket as arrowed
direction in picture “B” at right.
3. After push the bracket to the
end of winding slot, please
VESA 75mm Standard
fasten the screws which are just
rotated at step 1 as showing on
the picture “C”.
4. After fix this bracket, the LM-6100 series monitor
can lock with VESA mount arm.
LM-6600 series
Base Mount
4
B
C
1. Inquire for technical support from your dealer to set the power support
in the VGA port of the FT system following the relevant Technical
Manual of the FT system. Please note that once the VGA port is no
longer to be occupied by the LM-6601A, this power support must
be discontinued!
2. Unfold down the semi-circular base tongue of the LM-6601A main
unit and apply the L shape bracket on this base tongue. Use the 2
screws in the accessory bag to fix the bracket over the base tongue as
circled in the right picture. Note that the slots for the screws on the
bracket allow some adjustment on position of LM-6601A for
application.
3. Refer to the User’s Manual of the FT system
about “INSTALLING BASE MOUNT KIT”
to open back cover and remove the 2
arrowed screws to remove the pole cover.
Preserve the 2 screws for the next step.
4. Install the slender part of the L shape bracket
to the hole for pole cover and screw it to top
cover of FT base tightly at the arrowed holes
as in the left picture and result is shown at the
right.
5. Connect the VGA cable that has both 3 x 5
D sub male ends to VGA port at rear of
LM-6601A and the VGA port of host
system. Screw in the cable to connectors
at both ends.
6. There is no need to install driver for use of
LM-6601A. However, the supported display modes are tabulated at
last part of this manual
5
IV. OSD
A. OSD buttons
LM6100series
LM-6600 series
OSD Button
NEXT Button
+ Button
Button
Power Switch
-
“OSD” button: To enter OSD setup menu, or to perform function selected
in OSD operation.
“NXT” button: To go to next option function.
“” “” button: To increase setting.
“” “” button: To decrease setting.
“” “” button: To turn the monitor power ON/OFF. The monitor can be
turned OFF only when there is video signal and can be turned ON only
when there is video signal and after the “Turn Off Panel” message
vanishes. The default status is set to ON when power is supplied unless
manually turned OFF. Since this button controls only the display power
but not the display controller, please try disconnect the power cable or
the VGA cable once unfortunately the screen display goes into a mess.
6
B. OSD functions
Press “OSD” button with a normal display on the screen to activate the OSD
functions (On Screen Display adjustment). The OSD window will pop up on the
screen. On top part of this window is a Posiflex logo with the OSD firmware
version indicated to its lower right. Below this area is a row of icons for main
OSD menu. Below the main menu is a group of icons for submenu that
corresponds to one icon selected in the main menu. An analysis of the video
signal on resolution and refresh rate will be displayed at the bottom. Applicable
icons in the main menu and its subsequent menus are explained below.
“MAIN MENU”: There are in total 5 icons in this menu:
One of the 5 icons will be displayed in inverted color to indicate its relationship
with the submenu below. Pressing “NXT” button will shift the selected icon one
by one from left to right and then wrap around to the most left. Press “OSD”
button to enter the selected sub menu. If there is no button for OSD setting is
pressed within a period of time (about 5 seconds to 1 minute as programmed) the
OSD window will disappear with all the adjusted parameters saved.
Explanations on items in sub menu are as below.
“BRIGHTNESS / CONTRAST ADJUST SUBMENU”: There are 3
icons in this submenu:
Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among brightness, contrast and exit.
“BRIGHTNESS ADJUST”: When this item is selected, there will
be only the brightness icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” button
to increase brightness. Press “-” to decrease. Press “OSD” button to save
the current setting and return to “Brightness/Contrast submenu”.
“CONTRAST ADJUST”: When this item is selected, there will be
only the contrast icon with an adjustment indication bar under it between
the main menu area and the video signal mode. Press “+” button to
increase contrast. Press “-” to decrease. Press “OSD” button to save the
current setting and return to “Brightness/Contrast submenu”.
“EXIT”: Return to “Main menu”.
7
“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:
Press “OSD” button to select item or return to main menu. Press
“NXT” button to select among auto color adjust, auto RGB reset, Color balance
adjust and exit.
“AUTO COLOR ADJUST”: Upon an “OSD” button press on this
icon the monitor will perform an automatic color adjustment and exits the
OSD window leaving 2 icons below at center of the screen. Press “NXT”
button to switch the selection. Press “OSD” button to make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“AUTO RGB RESET”: Upon an “OSD” button press on this icon
the monitor will perform an automatic RGB reset and exits the OSD
window leaving 2 icons below at center of the screen. Press “NXT” button
to switch the selection. Press “OSD” button to make the choice.
“ACCEPT”: Accept the reset result.
“REJECT”: Decline the reset and return to previous setting.
“COLOR BALANCE ADJUST”: When this item is selected, there
will be 7 icons in this item:
between main menu
area and the video signal mode. Press “OSD” button to select an item or
return to color adjust submenu. Press “NXT” button to select among
separate color adjust, 4200K, 5000K, 6500K, 7500K, 9300K and exit.
“SEPARATE COLOR ADJUST”: When this item is
selected, there will be 3 adjustment indication bars between the main
menu area and the video signal mode. Press “NXT” button to select
among the 3 colors Red, Green and Blue respectively. Press “+”
button to intensify that color. Press “-” to reduce. Press “OSD”
button to save the current setting and return to “Color balance adjust
submenu”.
“4200K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 4200 degrees Kelvin.
“5000K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 5000 degrees Kelvin.
“6500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 6500 degrees Kelvin.
8
“7500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 7500 degrees Kelvin.
“9300K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 9300 degrees Kelvin.
“EXIT”: Return to “Color adjust submenu”.
“EXIT”: Return to “Main menu”.
“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this
submenu:
Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among auto geometry adjust,
horizontal size, phase, horizontal position, vertical position and exit.
“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press on
this icon the monitor will perform an automatic geometry adjustment and
exits the OSD window leaving 2 icons below at center of the screen. Press
“NXT” button to switch the selection. Press “OSD” button to make the
choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“HORIZONTAL SIZE”: When this item is selected, there will be
only the horizontal size icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” button
to increase horizontal size. Press “-” to decrease. Press “OSD” button to
save the current setting and return to “Geometry adjust submenu”.
“PHASE”: When this item is selected, there will be only the phase
adjust icon with an adjustment indication bar under it between the main
menu area and the video signal mode. Press “+” or “-” button to adjust the
pixel synchronization phase for best picture display. Press “OSD” button
to save the current setting and return to “Geometry adjust submenu”.
“HORIZONTAL POSITION”: When this item is selected, there
will be only the horizontal position icon with an adjustment indication bar
under it between the main menu area and the video signal mode. Press “+”
or “-” button to shift the screen display to right or left. Press “OSD” button
to save the current setting and return to “Geometry adjust submenu”.
9
“VERTICAL POSITION”: When this item is selected, there will
be only the vertical position icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” button
to shift up the screen display. Press “-” to shift down. Press “OSD” button
to save the current setting and return to “Geometry adjust submenu”.
“EXIT”: Return to “Main menu”.
“TOOLS SUBMENU”: When this item is selected, there are 5 icons in
this submenu:
Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among OSD submenu, reset to default,
phase, smoothness / sharpness adjust, mode select and exit.
“OSD SUBMENU”: When this item is selected, there are 4 icons in
this submenu:
Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among OSD time, OSD
horizontal position, OSD vertical position and exit.
“OSD TIME”: When this item is selected, there will be only
the OSD time icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+” or
“-” button to adjust the waiting time for OSD operation before OSD
termination between 5 to 60 seconds. Default is 30 seconds. Press
“OSD” button to save the current setting and return to “OSD
submenu”.
“OSD HORIZONTAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area and
the video signal mode. Press “+” button to shift OSD window right.
Press “-” to shift left. Press “OSD” button to save the current setting
and return to “OSD submenu”.
“OSD VERTICAL POSITION”: When this item is selected,
there will be only the vertical position icon with an adjustment
indication bar under it between the main menu area and the video
signal mode. Press “+” button to move OSD window downward.
Press “-” to go upward. Press “OSD” button to save the current
setting and return to “OSD submenu”.
“EXIT”: Return to “Tools submenu”.
10
“RESET TO DEFAULT”: Pressing “OSD” button on this icon will
set all parameters back to the status when the monitor left factory.
“SMOOTHNESS / SHARPNESS ADJUST”: When this item is
selected, there will be only the smoothness / sharpness adjust icon with an
adjustment indication bar under it between the main menu area and the
video signal mode. Press “+” button to increase smoothness of display
(decrease sharpness). Press “-” to go the other way. Press “OSD” button to
save the current setting and return to “OSD submenu”.
“MODE SELECT”: Pressing “OSD” button on this icon will have
no effect at all if the display mode is not one of the confusing modes. The
confusing modes here mean 640 x 400 or 720 x 400 in display resolution
as both mode have refresh rate of 70Hz, horizontal frequency of 37.9KHz
and pixel frequency of 31.5MHz making it impossible for automatic select.
These modes are not used in normal Windows display.
“EXIT”: Return to “Main menu”.
“EXIT”: Exit OSD setup with all adjustment saved.
11
V. SUPPORTED DISPLAY MODES
For video signals beyond the supported display modes, there will be a message
“Out Of Range” on middle of screen. Maximum supported color depth is 18 bits
or 262,144 colors. Supported display modes are as in the table:
Display Resolution
Refresh Rate (Hz)
Horizontal Frequency (KHz)
640*400
70
37.9
60
31.5
640*480
72
37.9
75
37.5
720*400
70
37.9
56
35.1
60
37.9
800*600
72
48.1
75
46.9
60
48.4
1024*768
70
56.5
75
60
警告使用者
這是甲類的資訊產品,在居住的環
境中使用時,可能會造成射頻干
擾,在這種情況下,使用者會被要
求採取某些適當的對策。
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising