Posiflex | KS-6910/KS-7210 series | User manual | Posiflex KS-6910/KS-7210 series User Manual

Posiflex KS-6910/KS-7210 series User Manual
KS – 6910/7210 series
Fan Free Touch Terminal
w/ Mini Slim Base
User’s Manual
Rev.: B0
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions manual, may
cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection
against interference when operated in a commercial environment. Operation
of this equipment in a residential area is likely to cause interference in which case the user at his
own expense will be required to take whatever measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized technicians opens
the machine. The user should consult his/her dealer for the problem happened. Warranty voids if
the user does not follow the instructions in application of this merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex
will assume no liability for any technical inaccuracies or editorial or other errors or omissions
contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including
without limitation loss of data or profits, resulting from the furnishing, performance, or use of this
material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims any
warranties, expressed, implied or statutory, including without limitation implied warranties of
merchantability or fitness for particular purpose, good title and against infringement.
The information in this manual contains only essential hardware concerns for general user and is
subject to change without notice. Posiflex reserves the right to alter product designs, layouts or
drivers without notification. The system integrator shall provide applicative notices and
arrangement for special options utilizing this product. The user may find the most up to date
information
of
the
hardware
from
web
sites:
http://www.posiflex.com
or
http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage peripheral.
Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this
or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
or otherwise, without prior express written consent from Posiflex Technology, Inc. the publisher of
this documentation.
© Copyright Posiflex Technology, Inc. 2011
All brand and product names and trademarks are the property of their respective holders.
P/N: 16440901030
Part 1
ALERT TO OUR HONORABLE CUSTOMERS:
Please always read thoroughly all the instructions and documents
delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.
This product contains inside a Lithium battery. Please always
follow local environmental protection laws / regulations for disposal
of used batteries and always replace only with battery of same type.
DAILY MAINTENANCE GUIDE
For regular cleaning of the KS systems, please use only soft haired brush or
dry soft cloth. You may use moist soft cloth to remove stains when necessary.
Apply only proper amount of mild neutral detergent for obstinate stains. Please
note that never use Acryl dissolving solvent or Polycarbonate dissolving
solvent. You may apply ammonia-based glass cleaner only on the screen
surface.
Part 2
7
INTRODUCTION
PRODUCT PICTURES – KS6910/7210TS
Front View
Rear View
1
1
16
2
6
3
7
4
8
5
Side Views
1
1
2
11
10
12
10
Bottom View
13
Part 3
PRODUCT PICTURES – KS6910/7210HS
Front View
Rear View
9
15
16
2
3
6
4
7
8
14
5
Side Views
2
11
10
12
10
Bottom View
13
Part 4
PRODUCT PICTURES – KS6910/7210
Front View
Rear View
1
16
3
6
4
7
8
5
Side Views
11
10
12
Bottom View
13
Part 5
PARTS IDENTIFICATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
MSR kit (KS6910/7210, KS6910/7210TS)
Handset (KS6910/7210TS, KS6910/7210HS)
Touch panel / LCD panel
Power and status indicators
Speakers
Hinge
Base Stand back cover
Cable exit
Emergency button (KS6910/7210HS only).
Base cover hook
Power switch push open cover.
Sundries through for pencils, paper clips etc.
Rubber feet with fixing screw
Control Buttons (KS6910/7210HS only).
Camera (KS6910/7210HS only).
HDD bay or CF card reader.
PRODUCT FEATURES
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
k)
Standard Features:
High quality handset for VoIP applications
(KS6910/7210TS, KS6910/7210HS)
Built-in Microphone and speaker for hand free operation.
(KS6910/7210HS)
Optional Build-in angel adjustable camera for more applications such as
Video call through VoIP software of KS-6910/7210HS.
Control buttons in front bezel and individual emergency button for
KS-6910/7210HS for particular usage.
CPU:
Intel D425, 512K Cache, 1.80 GHz (KS-6910 series)
Intel D525, 1M Cache, 1.80 GHz (KS-7210 series)
Fan free structure for harsh environment
Data storage device: SATA HDD, CF card or SSD HDD.
Support WinCE, POSReady, Windows 7 and Linux OS
High quality 10” TFT active matrix LCD panel with 1024X768
resolutions for KS-6910/7210HS and KS-6910/7210TS, and 800 X 600
resolutions for KS-6910/7210.
Vertical type LCD panel with easy tilt angle adjustment from 20° to
90°
Durable resistive type touch panel that endures 10 million touches min.
at same spot.
Part 6
l)
m)
n)
o)
p)
q)
r)
s)
t)
Various I/O ports supported, including:
1. 3 serial ports with 2 in form of DB9 connectors and 1 of 10 pin
RJ45 type modular connectors. COM1/2/3 are with capability for
+5V DC support through software setting.
2. 4 standard USB 2.0 ports
3. One LAN port Ethernet 10/100/1000 Base T with LAN status
indicators on jack (green for link, orange for data transmission)
4. One 2 pin type DC 12 V power input connector
5. One CR Port supports control 2 Cash Drawers
6. One Line-out port.
Touch control functions: left/right button, double click, drag & draw
VGA memory support Dynamic Video Memory Technology (DVMT) 4.0
Support high performance DDR-3 800 FSB, 1x SO-DIMM.
Integrated structure for top mount upgrade kit with software
programmable MSR parameters for POSReady or Windows 7.
Accidental power off protection – The power switch located at a
recessed side of main unit is unlikely to be activated in normal
operation.
Preconditioned power up function – by COM port MODEM ring or
LAN.
Supports power saving by suspension mode
Extremely low power consumption in system off.
Option Items:
Note: The underlined items in the following list means that option must be
set prior to shipment from the factory. The rest items can be set by the
dealers.
a) DDR3 SODIMM memory expansion up to 4GB max.
b) Integrated top mount upgrade kit(can add by dealer):
MSR in USB interface for KS-6910/7210, KS-6910/7210TS.
c) Integrated base mount upgrade kit:
LCD Pole display
VFD Pole display
d) Wireless LAN adaptor in USB interface
e) Preload OS: WinCE, POSReady, Windows 7 or Linux.
f) Optional SSD module in main unit.
g) RJ45 to DB9 serial port conversion cable
h) LPT interface conversion cable
i)
Split cable for 2 cash drawer control.
j)
WiFi Module kit.
Part 7
INSTALLATION GUIDES
CAUTION: Before any installation or cable connection to the set, please
always make certain that the system is turned off and the
external power source to the set is removed to prevent electric
hazard! Never touch any metal pin in the connectors or
circuits to avoid high voltage hazard or electrostatic discharge
damage unless the operator is well grounded. Failure to do the
above will void the product warranty!
TILTING LCD PANEL
The tilting mechanism in KS-6910/7210 series utilizes hinges
and there is no particular skill to turn the LCD panel to most
suitable angle for either viewing or convenience in cable
connection.
USING THE TERMINAL
Using the built-in handset is just as easy as using
normal telephone. Through the setting of
applications, it can be combining with optional
build-in camera become a Video with VoIP
terminal. Besides, there is a status indicator nearby
the handset and it can be indentify the phone call
status without showing in the LCD screen.
There is an Emergency Button in the top of KS6910/7210HS which can be program for particular
usage such as elderly emergency call out help.
For KS-6910/7210HS, there are 5 buttons in the
front bezel which are Volume increase and decrease
control, Home, Camera and Hand free.
“Home” button can bring you to the main page of
software and “Camera” button can switch On/Off the
camera module. These buttons are programmable
and able to control software functions directly to
provide more convenience of terminal exercise.
The build-in camera can be adjusting 90° to
completely block the camera for personal privacy.
90°
Part 8
CABLE ROUTING
DISCONNECTING ALL CABLES
With the LCD panel turned to most backward position, the main I/O connector
area will be easily accessible at bottom side of the main unit. Please first note
orientations of every existing cable connection and then disconnect every
cable properly before any further reconfiguration of cable connections. Please
note that the click lock spring has to be pressed down prior to pulling out the
connector such as the LAN port or the 2 alternate RJ45 form COM ports.
Please also note that the fixing screws have to be loosened free prior to
disconnection such as the 2 regular DB9 form COM ports. Please always hold
the connector head instead of pulling on the cable wire when disconnecting
any connector. Failure to do this could damage the cable and jack that is
considered as an artificial destruction. Damages due to incorrect
disconnection operation are not covered by product warranty!
OPENING BASE BACK COVER
In order to settle the touch terminal
properly in a point of sale system, all
the cable connections have to be
routed through its base. Therefore,
please observe the side view pictures
of the base trunk at the left and
release the triangle marked hooks to
remove the back cover.
CABLE ROUTING IN BASE
For cable routing in the undetachable mini slim base,
please refer to the picture at left. There are 2 cable tie
holder slits on the metal bracket for the trunk as
arrowed in the picture. Hold all the external cables
with a cable tie through the right cable tie holder slit
and leave the cables tied to the left holder slit. Have all
cables to pass through the oval hole on the trunk to
come out of the front side of trunk. Connect all the
cable ends to main unit. Be sure not to damage any
cable during this operation.
Part 9
BASE MOUNT UPGRADE KIT (OPTION)
For the system with mini slim base, the
LCD customer display PD-309/U or the
VFD PD-2605/U can be attached to
either rear corner of base bottom. Refer
to the pictures at right. Use the 3
attached screws to fix the metal base
plate of the PD to bottom plate of mini
slim base at the circled positions. Connect the interface cable
to go into the base through cable exit arrowed at right to the
main unit.
PREPARING THE MAIN UNIT
On the back of the
main unit, there is a
service window visible
through the oval cable
passage when the base
back cover is removed.
Service Window Lock Screw
It is recommended to
Remove the 2 hinge fixing screws as triangle pointed in the upper right picture
and remove the arrowed service window lock screw to open the cover plate
and find several jumpers and a reserved LPT port as illustrated the lower right
picture. Please consult your dealer for technical support on setup of these
jumpers. Please note that only those qualified technicians may adjust in the
service window with information from Posiflex and the contents in the service
window may change without notice as time develops. The option LPT
conversion cable should be applied to the connector as arrowed in left picture
below. Route the
conversion
cable
from bottom side of
the service window
plate to connect the
usual
cable
for
parallel
device.
LPT Connector
Please notice that
when using the LPT conversion cable, the metal plate of service windows
can not be use and the service windows will be open!
Part 10
CONNECTING CASH DRAWER (OPTION)
The RJ11 connector in I/O area of the system can be used for controlling most
of the common cash drawers available on the market. However, it is most
recommended to use Posiflex CR-2200, CR-3100, CR-4000, CR-4100 or CR6300 for best compliance to operate the opening mechanism and to monitor the
drawer open status.
The user may also purchase the optional 2-in-1 cash drawer control cable to
control 2 cash drawers in 1 port. It has a 6-pole plug at one end and two 8-pole
plugs at the other. The 6-pole plug should be inserted in the connector marked
“CR” found in the I/O area in the system. Each 8-pole plug should be inserted
into the connector marked “signal cable from POS Printer” at the rear of one of
the cash drawers.
Wi-Fi USB ADAPTER (OPTION)
Wi-Fi USB adapter is a USB based Wi-Fi module utilizing the high-speed data
communication at up to 150 Mbps. It realized in the 2.4G Hz radio band by
adapting IEEE 802.11N wireless standard.
Please refer to the User’s Manual attached (content in the CD/DVD delivered)
with this option for its driver setup or utility.
Do not connect the Wi-Fi USB adapter to the system before installation
the driver and utility.
CONNECTING CABLES
To have the re-assembled main unit with stand assembly ready for operation,
please connect all required cables to the appropriate connectors. Please make
sure that each connector is connected to the correct port with the correct
orientation. Damages due to incorrect connection or orientation are not
covered by product warranty!
Some connectors like the LAN, COM or CR connector have to be gently
inserted until a click is heard. It is recommended that connectors such as the
COM1/2 connector be screwed into place once seated. Adjust the slack of each
cable. Re-adjust the tilt angle of the screen for best viewing. Connect the
cables to appropriate external devices through the cable exit at the bottom of
stand assembly. Please make sure that each connector has to be connected to
the right device in the right way.
CAUTION: On doing any insertion or extraction of any connector, please
always hold the connector head itself instead of pulling on the
cable wire. Failure to do this could damage the cable and jack
that is considered as an artificial destruction and is not
covered by the warranty.
Part 11
USING THE TOUCH TERMINAL
APPLICATION ENVIRONMENT
It is very important that you check the following operational guidelines:
Ventilation
This terminal must NOT be operated in an environment with restricted
ventilation. There must be at least 25 mm air clearance around any top or side
ventilation holes with a free flow of air around the unit at ALL times for the
installation.
Operating Environment
The equipment must not be operated or stored in extremes of both temperature
and humidity/moisture. (Operating range 0°C to 40°C and up to 80%
humidity – none condensing, max. wet bulb 26°C)
Power Supply
The operating voltage range of the power adaptor should cover the local power
supply for proper operation. The power cable, the power outlet and any power
fusing arrangements must conform to local safety regulations.
Please never do any connection / disconnection when system is still powered
on. Please always keep the external power adaptor in a free air circulation.
POWER ON/OFF CONTROL
Power Indicator
There is a power indicator LED at center of lower rim of LCD panel. This
LED lights up yellow when external power is ready and turns to blue when
system power is turned ON.
KS6910/7210HS
KS6910/7210,
KS6910/7210TS
Part 12
Hardware Power Switch
The power switch located at side of the main
unit is a tactile pushbutton switch. This
switch controls the power on/off of the
system. This switch turns the system on
when pushed only and external power is
present. This switch turns the system off
when pushed again during power on status.
However, if the system hangs due to any
reason such as software resource conflict a
simple push on the switch may fail to turn
off the power. In this case, please utilize the
forced power off feature by pressing the
switch and holding for within 10 seconds.
There must always be at least 10 seconds waiting before switching on again
after the system is powered off successfully.
Automatic Power On Control
The system may also turn on according to some preset conditions such as
Modem Ring Up and LAN Wake Up.
To utilize Modem Ring Up function, the user should enter the BIOS setup by
pressing “Del” key at system boot up, choose in “Power Management Setup”
and make the “Power On by Ring” enabled for Modem Ring Up. Save the
configuration and exit the BIOS setup program. The Preset Power On Control
will then be ready. For LAN wakeup, the item “Power On by LAN” must be
enabled in “Power Management Setup” and an operating caller system
connected through LAN to the system is required. It also requires a qualified
networking technician to check the LAN chip ID of the system for the caller
system to wake up.
When the terminal is turned off after a successful boot up with external power
continuously supplied, the preset automatic power on functions will keep
monitoring for the preset conditions and turn on the system when the preset
conditions are met.
Please note that if the terminal is improperly turned off before a complete boot
up procedure, the above preset power on control functions will be disabled
until next turning off after a complete boot up.
Part 13
DISPLAY ISSUES
Main LCD Display
For best viewing result please set your display resolution at 1024 x 768 with
high color. The system Video Memory is shared from system memory and it
support DVMT 4.0 technology.
SERIAL PORTS – COM1/2/3
For this terminal, there are 3 serial ports available. COM 1/2/3 can supply a +5
V DC through pin 9. COM1/2 ports are standard RS232 serial ports as status at
delivery. COM3 port is a RJ45 connector as status at delivery if the option
conversion cables are applied.
AUDIO OUTPUT SPEAKER
The audio port is arranged to have an internal audio speaker with maximum
audio power of 2W. (KS-6910/7210HS, KS-6910/7210TS)
CF MEMORY CARD READER
The CF memory card reader slot at right side of main unit accepts a type I CF
memory card only.
USB PORTS
There are in total 4 USB ports for external connection in I/O area.
TOUCH PANEL
All paragraphs below are applicable for models with touch panel only. The
user of those models without touch panel can ignore them and consider this
user’s manual ends here.
Mouse Emulation
The touch panel in KS system uses USB interface. When the touch driver is
properly installed, this touch panel works exactly like a standard mouse for
both interfaces. However, if the system is running under safe mode, most
drivers are disabled in this mode and the touch panel calibration is therefore
not guaranteed. It is recommended to use a standard USB mouse or keyboard
in this mode.
Part 14
All the below mentioned mouse emulation functions can be manipulated
through relevant software. The system can give a beep and a click on the left
button of a mouse at the point when the touch panel is touched. If the point
touched is dragged across the screen surface, it works as the mouse drag and
drop feature. If the point is touched, released and touched within a short time
interval, it is double-clicking left button of the mouse. To obtain the effect like
clicking on the right button of a mouse, touching any point on the screen
surface after touching the right-click sticky button results as a click on the right
button of the mouse at that point.
Posiflex USB Touch Manager
A program named “Posiflex USB Touch Manager” and a right-click sticky
button tool in the program group “Posiflex USB Touch Tools” is installed in
the preloaded Windows system with a USB interface touch panel controller.
This program can also be obtained by download from the POSIFLEX web site.
警告使用者
警告
本電池如果更換不正確會有爆炸的危險
請依製造商說明書處理用過之電池
T31454
這是甲類的資訊產品,在居住的環
境中使用時,可能會造成射頻干
擾,在這種情況下,使用者會被要
求採取某些適當的對策。
Part 15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising