Sencor SVC 8501TI User's Manual

Add to my manuals
7 Pages

advertisement

Sencor SVC 8501TI User's Manual | Manualzz
SENCOR svc 850171!
EN = Bagged Vacuum Cleaner
Copyright © 2017, Fast CR, a.s. -1- Revision 12/2017
EN Bagged Vacuum Cleaner
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
= This vacuum cleaner may be used by children 8 years of age and older and by
persons with physical or mental impairments or by inexperienced persons, if they
are properly supervised or have been informed about how to use this vacuum
cleaner in a safe manner and understand the potential dangers. Children must
not play with the vacuum cleaner. Cleaning and maintenance performed by the
user must not be performed by unsupervised children. Keep the vacuum cleaner
and its accessories out of reach of children that are younger than 8 years of age.
« This vacuum cleaner is designed for use in households, offices and similar types of
areas. Do not use in industrial surroundings.
= Do not expose the vacuum cleaner to direct sunlight and do not place it near an
open fire or appliances that are a source of heat.
= Before connecting the power cord to a power socket, check that the technical details
on the vacuum cleaner’s rating label match the electrical voltage in the socket.
= Make sure the power cord is not touching a hot surface or sharp objects.
= Do not submerge the vacuum cleaner under water or any other liquid and do not
rinse it under running water.
= Before turning on the vacuum cleaner, make sure that the dust bag is inserted inside
and that the inflow micro-filter and the outflow HEPA filter are installed in their place.
= When the vacuum cleaner is running, ensure that the air outlets and the suction
opening are not blocked.
= Do not use the vacuum cleaner to vacuum the following items:
— smouldering cigarettes, burning items, matches or embers;
— water and other liquids;
— flammable or volatile materials;
— sharp items, e.g. broken glass, needles, pins, etc;
— flour, wall plaster, cement and other building materials;
— larger pieces of paper or plastic bags, which can easily block the suction opening.
= Vacuuming of some types of floors or floor surfaces can create a electrostatic
discharge, which presents no danger to the user.
= Do not place the suction nozzle or tube against any parts of the face.
« Always turn off the vacuum cleaner and disconnect it from the power socket when
leaving it without supervision, after finishing using it and before cleaning it.
= Disconnect the power cord from the power socket by pulling on the plug, never
pulling on the cord. Otherwise, this could damage the power cord or the socket.
Hold the power cord in your hand when winding it up.
Copyright © 2017, Fast CR, a.s. -2- Revision 12/2017
= In the event that the power cord is damaged, it must be replaced by an authorised
service centre or by a similarly qualified person, this will prevent the creation of a
dangerous situation. It is forbidden to use the vacuum cleaner if it has a damaged
power cord.
= Do not use the vacuum cleaner if it is not working correctly, if it has been damaged
or has been submerged in water. Do not repair the vacuum cleaner yourself or make
any adjustments to it. Have all repairs performed at an authorised service centre.
By tampering with the appliance, you risk voiding your legal rights arising from
unsatisfactory performance or quality warranty.
Copyright © 2017, Fast CR, as. -3- Revision 12/2017
AN O
X у
\\
Ne
NE
< — N MINO N
Copyright © 2017, Fast CR
nmi rin
Copyright © 2017, Fast CR, as. -5- Revision 12/2017
Bagged Vacuum Cleaner
User's manual
= Prior to using this appliance, please read the user's manual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user's manual.
Keep this user's manual in a safe place where it can be easily retrieved for future use.
= We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
DESCRIPTION OF THEVACUUM CLEANERAND ITS ACCESSORIES
A1 Automatic power cord winding A16 Washable outflow HEPA filter
button is placed behind the grill.
A2 Stainless steel grill A17 Dust bag*
A3 Electronic suction power control A18 Dust bag holder
A4 Lid of storage area for dusting brush A19 Grill of the inflow micro-filter
and crevice nozzle A20 Washable inflow micro-filter
AS Full dust bag indicator is placed in the grill.
A6 Lock for lid of storage area A21 Flexible hose with mechanical
A7 Flexible hose connection hole suction power control in the handle
A8 Top cover lock A22 XXL telescopic metal tube
A9 Integrated handle A23 Floor nozzle with an extensible
A10 On/Off button of the vacuum brush
cleaner A24 Flap for extending and retracting
A11 Groove for the horizontal parking the brush
position A25 Turbo brush
A12 Rubber-coated rear travel wheel
A13 Front rotating travel wheel
A14 Groove for the vertical parking
A26 Suction power control
A27 Hard floor nozzle
A28 Mini turbo brush
position A29 Long flexible crevice nozzle
A15 Removable grill of the outflow HEPA A30 Dusting brush
filter A31 Crevice nozzle
*Note:
One disposable synthetic dust bag is included with the product. Synthetic
dust bags last longer, are more durable and provide better filtration than
standard paper bags.
Note:
СЯ The dusting brush A30 and crevice nozzle A31 are stored in the storage
area under the lid A4.
INTENDED USE OF THE ACCESSORIES
= The basic floor nozzle with an extensible brush A23 is suitable for vacuuming
smooth hard surfaces and carpets. When vacuuming smooth hard floor surfaces,
extend the brush, and when vacuuming carpets retract it. Use flap A24 to extend
and retract the brush.
= The turbo brush A25 is suitable for vacuuming smooth hard surfaces and carpets
with a low pile height. Thanks to the rotating brush, it very quickly and effectively
removes ingrained dirt, threads, animal fur, hair, etc. Use the sliding suction power
control A26 to set the suction intensity.
= The hard floor nozzle A27 ensures perfect and yet gentle vacuuming of smooth
hard surfaces thanks to the brush being from 100% natural bristles. It can be used
to vacuum floors that are sensitive to scratching such as wooden or floating floors,
marble floors, tiles, linoleum, etc.
= The mini turbo brush A28 is the ideal helper for removing animal fur, hair, etc,
while at the same time being suitable for vacuuming hard-to-reach places. Its use
is not limited to the home, and can be used for vacuuming the car. It quickly and
effectively removes hair, animal fur and other materials from car seats, upholstery,
pillows and other textile surfaces.
= The long flexible crevice nozzle A29 serves to vacuum very hard-to-reach places
anywhere in your car.
= The crevice nozzle A31 can be used for vacuuming hard-to-reach places and the
dusting brush A30 is used for vacuuming various types of furniture.
PREPARING FOR USE
= Make sure that the dust bag A17, inflow microfilter A20 and outflow HEPA filter
A16 are properly installed.
= Insert the end of the flexible hose A21 into the hole A7 and turn it clockwise to
secure it in place.
= Attach the telescopic tube A22 on to the handle of the flexible hose A21. Slide the
ring that is located on the telescopic tube A22 towards the handle of the flexible
hose A21 to release the extension lock on the telescopic tube A22. After releasing
the lock, set the length of the tube A22 by sliding its extensible part in or out. When
the ring is released, it will lock in at the set length.
= Select the type of accessory that you wish to use and attach it to the free end of the
telescopic tube A22. Certain types of accessories such as for example A28, A29, A30
or A31 are attached directly on to the handle of the flexible hose A21.
USING THE VACUUM CLEANER
= Pull on the power plug to wind out the required length of the power cord and
connect it to a power socket.
A
= To start the vacuum cleaner, press button A10. Suction power can be set using the
electronic control A3 or the mechanical flap on the handle of the flexible hose A21.
= When you have finished using the vacuum cleaner, turn it off by pressing button A10
and disconnect the power cord from the power socket. To wind the power cord back
into the vacuum cleaner, press and hold button A1 until its entire length is wound
up. Gently hold the power cord with one hand while winding it up.
Aq
PARKING POSITION OF THE VACUUM CLEANER
= When not using the vacuum cleaner, you may put it in the parking position. For the
horizontal parking position, slide the stopper on the nozzle A23 or A27 or turbo
brush A25 into the groove A11, see fig. B1.
= For the vertical parking position, first set the shortest length of the telescopic tube
A22. Then put the vacuum cleaner into a vertical position and slide the stopper
on the nozzle A23 or A27 or the turbo brush A25 into the groove A14, see fig. B2.
Attention:
The yellow mark on the power cord indicates the approaching end of its length,
and the red mark indicates the complete end of its length. Do not attempt to
pull the power cord past this mark.
Note:
If the power cord is not wound up completely, release button A1, and pull
the power cord out of the vacuum cleaner by approximately 50 cm and then
try again to wind it up.
MAINTENANCE AND CLEANING
= Before cleaning it, always make sure that the vacuum cleaner is turned off and
disconnected from the power socket.
Changing the dust bag
= The red coloured indicator A5 signals the need to replace the dust bag A17.
= Release the lock A8 and tilt open the top cover of the vacuum cleaner. Remove the
used dust bag A17 from the holder A18 and insert a new bag intended for this type
of a vacuum cleaner in its place. After replacing the bag A17, close the top cover
of the vacuum cleaner. It will not be possible to close the top cover of the vacuum
cleaner unless the bag is correctly inserted in the holder A18.
= If the dust bag is not replaced in time, the vacuum cleaner’s suction power will
be reduced.
Cleaning and replacing the inflow microfilter and the outflow HEPA filter
= Release the lock A8 and tilt open the top cover of the vacuum cleaner. Slide the grill
A19 out of the vacuum cleaner and take the micro-filter A20 out of it. Rinse it under
running lukewarm water and allow to dry naturally. Then reinsert it and close the
cover. In the event that the micro-filter A20 is showing signs of wear or it is heavily
soiled, replace it with a new one.
= Release and remove the grill A15. Remove the HEPA filter A16 from the vacuum
cleaner. In the case of light soiling, tap it out. We recommend doing this away from
living areas. In the event of greater soiling, wash it under a weak current of running
lukewarm water so that the water washes the dirt out of the folds. Allow the HEPA
filter A16 to dry naturally, then reinsert it and secure it in place with the grill A15.
It is recommended to replace the HEPA filter with a new one after 6 months of use.
= When filters are soiled, their effectiveness is reduced, so do not neglect their cleaning.
A
Cleaning the flexible hose, telescopic tube, floor nozzle, hard floor nozzle, mini
turbo brush, flexible crevice nozzle, small crevice nozzle and the dusting brush
= Ifthe accessories are soiled, take them out and clean away all dirt (dust, hair, animal
fur, etc.).
Attention:
Before putting the filters back into the vacuum cleaner, make sure that they
are completely dry.
Cleaning the turbo brush
= Release the latches along the sides of the turbo brush A25, see figure C1. Remove
the front cover and remove all dirt, hair, animal fur, etc. from the rotary brush and
Note: the inner area. After cleaning, put the front cover back and secure it in place using
For removal, turn the end of the hose A21 anticlockwise and pull it out of the locking latches.
the hole A7. = Press the cover latches located on the underside of the turbo brush A25 to release
them, see figure C2. Remove the cover and remove any soils from the inner area of
the turbo brush A25. Put the cover back in its place. An audible click will be heard
when it slides back into place.
Copyright © 2017, Fast CR, a.s. -6- Revision 12/2017
Cleaning the outer surface of the vacuum cleaner
= Clean the outer surface using a dry or a lightly dampened cloth. Then wipe it
thoroughly dry.
= For cleaning the vacuum cleaner, do not use steel wool, abrasive cleaning products,
solvents etc.
= Do not submerge the vacuum cleaner under water or any other liquid and do not
rinse it under running water.
TECHNICAL SPECIFICATIONS
Rated voltage range 220-240V
Rated frequency. 50/60 Hz
Rated power input 600W
Electrical shock protection class Il
Noise level 69 dB(A)
Dust bag capacity 31
HEPA filter efficiency class H13
Length of the power cord 8m
Operational radius 11m
The declared noise emission level is 69 dB(A), which represents a level À of sound power
with respect to a reference sound power of 1 pW.
Explanation of technical terminology
Safety class for electrical shock protection:
Class Il — Electrical shock protection is provided by double or heavy-duty insulation.
We reserve the right to change text and technical specifications.
PRODUCT INFORMATION SHEET
Name / trademark
A
Rated 600
* Class A+++ (highest efficiency class, low power consumption) to Class D (lowest
efficiency class, high power consumption).
** Approximate annual power consumption in kWh per year based on 50 cleaning
cycles. Actual power consumption will depend on how the appliance is used.
The values are determined pursuant to (EU) No. 665/2013 - Il.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at a site designated for waste in your municipality.
DISPOSAL OF USED ELECTRICALAND ELECTRONICEQUIPMENT
This symbol on products or original documents means that used electric
or electronic products must not be added to ordinary municipal waste.
For proper disposal, renewal and recycling hand over these appliances
to determined collection points. Alternatively, in some European Union
states or other European countries you may return your appliances to
the local retailer when buying an equivalent new appliance.
Correct disposal of this product helps save valuable natural resources
I and prevents potential negative effects on the environment and human
health, which could result from improper waste disposal. Ask your local authorities or
collection facility for more details.
In accordance with national regulations penalties may be imposed for the incorrect
disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer.
€ This product meets all the basic requirements of EU directives related to
( it.
Copyright © 2017, Fast CR, a.s. -7- Revision 12/2017

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement