AcuRite | Pro 5-in-1 Weather Station Reverse Color Display | User manual | Acurite Pro 5-in-1 Weather Station Reverse Color Display User Manual

Acurite Pro 5-in-1 Weather Station Reverse Color Display User Manual
Instruction Manual
Professional Weather Center
model 01141
CONTENTS
Unpacking Instructions............ 2
Package Contents................... 2
Product Registration................ 2
Features & Benefits: 5-in-1........ 3
Features & Benefits: Display..... 4
Setup..................................... 7
5-in-1 Sensor Setup................. 7
Display Setup......................... 8
Set the Time, Date & Units....... 9
Backlight Settings.................... 9
Placement Guidelines.............10
5-in-1 Sensor Installation......... 11
Using the Weather Center......12
Programmable Alarms............13
Troubleshooting.....................14
Care & Maintenance..............16
Calibrate the Rain Gauge.......17
Specifications.........................18
FCC Information....................18
Customer Support..................19
Warranty..............................19
Questions? Contact Customer Support at
(262) 729-4852 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.
Package Contents
1. Display with Tabletop Stand
2. 5-in-1 Sensor
3. Sensor Mounting Bracket
4. Mounting Hardware
5. Power Adapter
6. Instruction Manual
IMPORTANT
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 yearwarranty protection
www.AcuRite.com
2
Features & Benefits
7
1
2
9
11
3 4
5
8
6
10
5-in-1 SENSOR
5. T emperature & Humidity Sensors
(internal)
1. R
ainfall Collector Funnel
2. Solar Cell Panel
6. Mounting Point
Converts sunlight into power to run
internal aspirating fan.
7. W
ind Speed Anemometer
Internal Aspirating Fan
(not shown)
8. Wind Direction Vane
9. Mounting Bracket
Draws ambient air into sensor to reduce solar radiation
heating, resulting in more accurate
temperature measurement.
10. Mounting Hardware
3. A-B-C Switch
Includes 5 anchors and the following
screws:
Qty
Diameter
Length
5
#4
3/4”
1
#4
1/2”
1
#6
1/2”
4. Battery Compartment
11. Debris Filter
ID code that must match display’s
A-B-C switch to ensure units
synchronize.
Pre-installed to prevent debris from
entering the rain gauge.
3
Features & Benefits
Display
1
14
2
3
4 5
6
7
15 16 17 18 19 20 21 22
8
23 24 25
4
9
10
20 26
27
1112 13
28 29
DISPLAY FRONT
1. Sensor Low Battery Indicator
16.
Button
For viewing all-time high and
low records.
17.
Icon
Indicates low records are being
viewed.
2. Outdoor Sensor Signal Strength
3. Current Outdoor Temperature
Arrow icon indicates direction the
temperature is trending.
4.
Icon
Indicates high records are being
viewed.
18. Average Wind Speed
Average of all speeds over the
past 2 minutes.
5. Previous 2 Wind Directions
19. Date
6. Current Wind Direction
20. V and
Buttons
For setup preferences and viewing
today's high & low records.
V
7.
Current Wind Speed
8. Learning Mode Icon
Disappears after weather forecast
self-calibration is complete
(see page 12).
21. Peak Wind Speed
Highest speed from past
60 minutes.
9. 12 to 24 Hour Weather Forecast
Self-Calibrating Forecasting pulls
data from outdoor sensor to
generate your personal forecast.
22.
Icon
Indicates display is in
auto-dimming brightness mode
(see page 9).
10. Current Rainfall
Rainfall recorded since 12:00 am.
23.
Button
For setup preferences.
11.
24. Clock
Icon
Indicates an alarm value has
been activated.
25. Current Barometric Pressure
Arrow icon indicates the direction
the pressure is trending.
12. Previous Rainfall Data
13. Rainfall Rate
Only applies to current rainfall data.
26. Moon Phase
27.
14. Current Outdoor Humidity
Arrow icon indicates the direction
the humidity is trending.
Button
For alarm setup.
28. Current Indoor Temperature
Arrow icon indicates the direction
the temperature is trending.
15. Seasonal Display
Heat Index calculation displays
when temperature is 80°F (27°C)
or higher. Dew Point calculation
displays when temperature is
79°F (26°C) or below. Wind
chill calculation displays when
temperature is 40°F (4°C) or
lower.
29. Current Indoor Humidity
Arrow icon indicates the direction
the humidity is trending.
5
Features & Benefits
1
2
3
8
4
5
6
7
DISPLAY BACK
1. Backlight Button
For momentary backlight and dimmer
settings.
2. Integrated Hang Holes
For easy wall mounting.
3. Backup Battery Compartment
4. A-B-C Switch
ID code that must match sensor’s A-B-C
switch to ensure units synchronize.
5. Plug-in for Power Adapter
6. Battery Compartment Cover
7. Power Adapter
8. RESET Button
Press and release to clear historical
record. Press and hold for 10 seconds
for full reset to factory defaults.
6
SETUP
5-in-1 Sensor Setup
1 Set the A-B-C Switch
Locate the A-B-C switch inside the
battery compartment. Set the A-B-C
switch to A, B or C. You must select
the same letter choices for both the
sensor and the display in order for
the units to synchronize.
2 Install or Replace Batteries
Batteries MUST be installed for
this product to operate. AcuRite
recommends high quality alkaline
or lithium batteries for the best
product performance. Heavy duty
or rechargeable batteries are not
recommended.
The 5-in-1 sensor requires lithium
batteries in low temperature
conditions. Cold temperatures can
cause alkaline batteries to function
improperly. Use lithium batteries in
the 5-in-1 sensor for temperatures
below -4ºF/-20ºC.
1. Slide off the battery compartment cover.
2. Insert 4 x AA batteries into the
battery compartment, as
shown. Follow the polarity
(+/-) diagram in the battery
compartment.
3. Replace the battery cover.
3 Remove Rain Gauge Stabilizer
Locate and remove the rain gauge
stabilizer (plastic tab) taped into
the bottom of the sensor. The rain
gauge will not function until this is
removed.
ABC
1
A-B-C Switch
Set to match
display
2
3
Install Batteries
4 AA Batteries
7
Rain Gauge Stabilizer
Remove and discard
Display Setup
3 Install or Replace Backup
1 Set the A-B-C Switch
Batteries (optional)
The A-B-C switch is located inside
the battery compartment. It can
be set to A, B or C. However, you
must select the same letter choices
for both the 5-in-1 Sensor and the
display in order for the units to
synchronize.
Insert 3 x AAA alkaline batteries
into the battery compartment,
as shown. Follow the polarity
(+/-) diagram in the battery
compartment.
2 Plug Power Adapter into
Electric Outlet
ABC
1
3
A-B-C Switch
Set to match sensor's
ABC switch
2
Install Backup
Batteries
3 AAA Batteries
(optional)
Plug in
Power Adapter
IMPORTANT: Batteries are a backup power source to
preserve records in the event of a power outage. Power
adapter is the recommended primary power source to
enjoy the full functionality of this product.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to
be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of
used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries
in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT
recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
8
Set the Time, Date & Units
Press the “ ” button, located on the front of the display, to enter SET MODE.
Once in set mode, the preference you are currently setting will blink on the display.
To adjust the currently selected (flashing) item, press and release the “ “ or
“V “ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button again to adjust the
next preference. The preference set order is as follows:
V
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (°F or °C)
WIND SPEED UNITS (mph, km/h, knots)
RAINFALL UNITS (inches or mm)
PRESSURE UNITS (inHg or hPa)
You will automatically exit SET MODE if no buttons are pressed for 20 seconds.
Enter setup mode at any time by pressing the “ ” button.
Display Backlight Settings
This weather station’s color display features three different lighting settings:
High (100%) brightness, Medium (60%) brightness and Low (15%) brightness.
When display is powered with the power adapter, backlight remains on at
100% brightness. Press the “ ” button once to dim to 60% brightness; press
again to dim to 15%, press a third time to enter AUTO-DIM mode. “ ” will
appear next to the clock.
NOTE: Pressing and holding the “ ” button for 5 seconds will disable the
backlight. Once any button is pressed, the backlight will return to your selected
setting.
AUTO DIM MODE: Automatically adjusts display brightness based on time of day.
6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m.= 15% brightness
9
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display and the sensor are critical to the accuracy and
performance of this product.
Display Placement
Place the display in a dry area free of dirt and dust. To ensure
accurate temperature measurement, place out of direct sunlight
and away from heat sources or vents. Display stands upright for
tabletop use or is wall-mountable.
5-in-1 Sensor Placement
The 5-in-1 sensor is designed to remain outdoors all year long.
Choose an open location with no obstructions above or around
the sensor for the most accurate measurements.
Important Placement Guidelines
Display and sensor must be within 330 feet (100 m) of each other.
MAXIMIZE WIRELESS RANGE
lace units away from large metallic items, thick walls, metal surfaces, or other
P
objects that may limit wireless communication.
PREVENT WIRELESS INTERFERENCE
lace both units at least 3 feet (.9 m) away from electronic devices (TV,
P
computer, microwave, radio, etc.).
LOCATE AWAY FROM HEAT SOURCES
Position sensor away from heaters, air conditioners, chimneys, exhaust vents,
asphalt and concrete (surfaces that radiate heat).
LOCATE AWAY FROM HUMIDITY SOURCES
Avoid installing the sensor near pools, spas, or other bodies of water. Water
sources may impact humidity accuracy.
LOCATE AWAY FROM SPRINKLER HEADS
DO NOT install the sensor where it will be sprayed by a sprinkler system. This
may force water inside the sensor.
LOCATE AWAY FROM WIND & RAIN OBSTRUCTIONS
DO NOT mount the sensor with obstructions around it.
Consider a location that is a wide open area, with few
structures around to ensure accurate wind measurement.
Visit us online to view installation photos and
video, or learn more about AcuRite technology:
www.AcuRite.com/5in1
10
View Video
5-in-1 Sensor Installation Guidelines
INSTALLATION HEIGHT Mount the sensor at a minimum height of 5 feet
(1.5 meters) off the ground, in an open area. Higher is better for wind
measurements - The National Weather Service recommends 33 feet
(10 meters) high!
MOUNTING OPTIONS The included mounting bracket it designed to screw
directly onto wooden posts or surfaces that are 2 x 4 (4.5 cm x 9.5 cm) or larger.
The sensor can also be mounted directly to common 3/4” (20 mm) steel pipe.
5-in-1 Sensor Installation
1. F
asten mounting base (included) to a post
or pole (not included) using the 4 longer
screws included in the hardware bag.
NO OBSTRUCTIONS
ABOVE OR AROUND
TH
SOU
2. Insert the mounting base into the hole on
the bottom of the sensor.
3. M
ake sure the arrows on the top of the
sensor are pointed in the proper direction
and the bubble level is centered. The
solar cell should be facing south to
properly orient the wind direction.
(1.5 meters)
4. F
asten the sensor into the mounting base
using the 2 shorter screws included in the
hardware bag.
The 5-in-1 sensor is now
ready to use.
Clear Data Collected During Installation
When installation is complete, press and release the “RESET” button, located
on the back of the display inside the battery compartment, to clear erroneous
data from the display.
Basic Setup is Complete
The 5-in-1 sensor will now synchronize with the display. It may take a few
minutes for synchronization to complete. If both or one of the units appear to
be functioning improperly, please refer to the troubleshooting section.
11
OPERATION
Using the Professional Weather Center
Learning Mode
Self-Calibrating Forecasting use a unique algorithm to analyze changes in
pressure over a time period (called Learning Mode) to determine your altitude.
After 14 days, the self-calibrated pressure is tuned in to your location and the
unit is ready for superior weather prediction.
Weather Forecast
AcuRite’s patented Self-Calibrating Forecasting provides your personal forecast of
weather conditions for the next 12 to 24 hours by collecting data from the sensor
in your backyard. It generates a forecast with pinpoint accuracy - personalized for
your exact location.
View the complete list of icons at www.AcuRite.com/acurite-icons
Barometric Pressure
Subtle variations in barometric pressure greatly affect the weather. This
weather station displays the current pressure with an arrow icon to indicate the
direction the pressure is trending (FALLING, STEADY, or RISING).
Moon Phase
Track the phases of the moon, conveyed through simple lunar phase icons:
NEW
WAXING
CRESCENT
FULL
1ST
QUARTER
High & Low Records
3RD
QUARTER
WANING
CRESCENT
High and low records for today and all-time are displayed for outdoor
temperature and humidity. Rain accumulation data is recorded for today, this
week, by month and by year. Today’s records automatically clear at 12:00am
midnight every day.
Press and release the “
“ button to cycle through all historical records.
While viewing historical records, a date and timestamp are shown for when
each value was recorded. You will automatically exit records if no buttons are
pressed for 8 seconds.
To manually clear a HIGH or LOW record, press and release the RESET button,
located in the battery compartment, while viewing the record(s) you wish to
clear. Dashes display to confirm you have cleared the record(s).
12
Programmable Alarms
This display features programmable alarms that sound an alert to notify you when a
value (for outdoor temperature, humidity, wind speed or rainfall) has been reached
or exceeded. When an alarm is triggered, the display emits an audible beep and
flashes data in the affected category. You can customize the alarms by turning ON
or OFF the alarms you’d like activated or deactivated, and by inputting your own
values to trigger the alarm.
Setup an Alarm
1. Press and release the “
” button until the reading for which you wish to set
an alarm is shown on the display. “ ” will be shown.
” appears.
” button. The current HIGH alarm value flash on
4. Press and release the “V “ or “
“ buttons to adjust the alarm’s HIGH value.
V
3. Press and release the “
the display.
“ buttons until “
V
2. Press and release the “V “ or “
5. Press and release the “
” button. If applicable, the current LOW alarm value
will be shown on the display.
7. Press and release the “
V
6. Press and release the “ ” button and then press and release the “V “ or “
buttons to adjust the alarm’s LOW value.
” button to cycle to the next reading.
Disable an Alarm
1. Press and release the “
” button until the reading for which you wish to
disable an alarm is shown on the display. “
” will be shown.
2. Press and release the “V “ or “ “ buttons until “ ” appears.
V
3. Press and release the “
” button to cycle to the next reading.
4. Repeat steps 1-3, as needed.
NOTE: To disable ALL alarms at once, press and HOLD the “
” button for 10 seconds.
You will automatically exit alarm SET MODE if no buttons are pressed for 10
seconds. Enter alarm SET MODE at any time by pressing the “
” button.
13
Troubleshooting
Problem
No outdoor sensor
reception
no bars
Outdoor
t emperature
is flashing or
showing dashes
Inaccurate forecast
Possible Solution
•R
elocate the display and/or the 5-in-1 sensor.
The units must be within 330 ft (100 m) of each
other.
• Make sure both units are placed at least 3 feet
(.9 m) away from electronics that may interfere
with the wireless communication (such as TVs,
microwaves, computers, etc).
•U
se standard alkaline batteries (or lithium
batteries in sensor when temperature is
below -4ºF/-20ºC). Do not use heavy duty
or rechargeable batteries. NOTE: It may
take a few minutes for display and sensor to
synchronize after batteries are replaced.
•S
ynchronize the units:
1. B
ring both the sensor and display indoors and
remove batteries/power adapter from each.
2. Reinstall batteries in outdoor sensor.
3. Reinstall batteries/power adapter in display.
4. L et the units sit within a couple feet of each
other for a few minutes to gain a strong
connection.
Flashing of the outdoor temperature may be an
indication of wireless interference.
• Make sure the A-B-C switch in the battery
compartments of both the display and sensor are
switched to the same letter. You may choose A, B or
C; but both units must match to sync up. Sometimes
changing to a different channel can help.
•W
eather Forecast icon predicts conditions for
the next 12 to 24 hours, not current conditions.
•A
llow unit to run continuously for 33 days.
Battery removal or resetting the display will
restart Learning Mode. After 14 days, forecast
should be fairly accurate, however Learning
Mode calibrates for a total of 33 days.
14
Troubleshooting
Problem
Possible Solution
Display screen
not working
• Check that the power adapter is plugged into
the display and an electrical outlet.
•C
heck that the batteries are installed correctly.
Batteries may need to be replaced.
•R
eset the display by pressing and HOLDING
the “RESET” button, located on the back of the
display. Date and time will need to be entered
after a reset.
Inaccurate
temperature or
humidity
•M
ake sure both the display and 5-in-1 sensor
are placed away from any heat sources or vents
(see page 10).
•M
ake sure both units are positioned away from
moisture sources (see page 10).
•M
ake sure 5-in-1 sensor is mounted at least 5 ft
off of the ground.
No rainfall
• Check to ensure the rain gauge stabilizer (plastic
tab) has been removed from the bottom of the
sensor (see page 7).
• Clear debris, such as leaves, out of the rain
collector funnel and debris screen.
• Calibrate the Rain Gauge (see page 17).
• Verify the sensor’s internal tipping lever is
moving freely by dripping a little water through
the rain collector. You should hear the lever
tipping. If you do not hear it, you may need to
clean inside the sensor. Video available at
www.acurite.com/5in1.
Inaccurate wind
readings
•W
hat is wind reading being compared to? Pro
weather stations are typically mounted at 30 ft
high or more. Make sure to compare data using
a sensor positioned at the same mounting height.
•C
heck location of the sensor. Ensure it’s mounted
a minimum of 5 ft in the air with no obstructions
around it (within several feet).
•Ensure wind cups are spinning freely. If they
hesitate or stop try lubricating with graphite
powder or spray lubricant.
If your AcuRite product does not operate properly after trying the
troubleshooting steps, visit www.AcuRite.com or call (262) 729-4852 for
assistance.
15
Care & Maintenance
Display Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
5-in-1 Sensor Care
Clean the Sensor
Clean with a soft damp cloth. Do not use caustic cleaners or abrasives that will
mar the polished surfaces of the rain collection funnel or the solar cell. Scratches
will result in decreased performance and reliability.
Insect Prevention
Insects may cause obstructions and interrupt data by nesting in or on the 5-in-1
sensor. To limit this problem, spray the OUTSIDE of the sensor with a household
insect repellent. Consult the insect repellent instructions prior to use.
Snow & Freezing Weather
The 5-in-1 sensor will not be damaged by freezing conditions. NOTE: If the rain
collector cup fills with snow and then melts, it will register as rain on the display.
Clean the Rain Collector Cup
Remove and empty rain collector debris filter. The debris filter is located in the
rain collector funnel. Remove from the top by gently squeezing and pulling out.
Clean the Wind Vane & Anemometer
Remove foreign matter from the outside of the sensor for free movement of the
wind vane and anemometer. If needed, use a small amount of spray lubricant,
clear silicone or graphite powder on the anemometer for improved movement.
Calibration
The indoor / outdoor temperature and humidity readings, and barometric
pressure can be calibrated on the display to improve accuracy. Calibration can
improve accuracy when sensor placement or environmental factors impact the
data accuracy.
“, “V “ and “
V
1. To access calibration mode, press AND HOLD the “
buttons simultaneously for at least 5 seconds.
”
2. To adjust the currently selected (flashing) item, press and release the “ “
or “V “ buttons to calibrate the data value higher or lower from the actual
reading.
V
3. To save your adjustments, press and release the “ ” button to adjust the
next preference. The “ ” icon will remain illuminated next to calibrated
values.
16
The preference set order is as follows:
OUTDOOR TEMPERATURE
OUTDOOR HUMIDITY
INDOOR TEMPERATURE
INDOOR HUMIDITY
BAROMETRIC PRESSURE (must be set to MANUAL mode to calibrate)*
*To change from AUTO to MANUAL pressure mode and vice versa, press
AND HOLD the “ ” button for at least 10 seconds. The display indicates
the current pressure mode selected,“auto” or “manual”.
After 20 seconds of inactivity, the display will save the adjustments and exit
calibration mode. Note: Calibrations will be erased if the display is reset or if
batteries are removed and the power adapter is unplugged.
Calibrate the Rain Gauge
The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy.
Items Needed: 5-in-1 sensor, display, plastic cup, pin, screw driver
1. First, ensure 5-in-1 sensor is perfectly level using built-in bubble level.
2. Place display close so you can monitor it during calibration.
3. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain
gauge and fill it with exactly 1 cup (8oz) of water, allowing the water to drip
into the rain gauge. You should hear the internal buckets tip and see water
drain through the rain gauge.
4. A few seconds after each bucket tip, the display displays rainfall in
approximately 0.01” or more increments.
5. The cup of water should take more than 20 minutes to empty; a quicker
period will result in inaccurate calibration. Try to simulate a normal steady
rainfall. When cup is empty of water, display should register 1.06”
Tips
• There should be nearly an equal number of water drops (about 25 water
drops) between bucket tips. If not, adjust the calibration screws on the
bottom of the 5-in-1 sensor until an equal number of water drops are tipping
the buckets. Then, restart the calibration procedure.
• If you don’t hear the buckets tipping and see water dripping alternately out
of each drain, there may be an issue with the rain gauge or it’s adjustment.
See Troubleshooting on page 15.
Adjustment
If the rain gauge doesn’t register close to 1.06”, make an EQUAL adjustment
to the two calibration screws on the bottom of the 5-in-1 sensor. Turning screws
clockwise increases rainfall; counter clockwise decreases rainfall.
• To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.
• To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.
• To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.
Watch the video at: www.acurite.com/5in1
17
Specifications
TEMPERATURE RANGE
Outdoor: -40ºF to 158ºF; -40ºC to 70ºC
Indoor: 32ºF to 122ºF; 0ºC to 50ºC
HUMIDITY RANGE
Outdoor: 1% to 99%
Indoor: 1% to 99%
WIND SPEED
0 to 99 mph; 0 to 159 kph
WIND DIRECTION
INDICATORS
16 points
RAINFALL
0.01 inches (0.25 mm) and up
WIRELESS RANGE
330ft / 100m depending on home construction materials
OPERATING FREQUENCY
433 MHz
Display: 5v, 250mA power adapter
3 x AAA alkaline batteries (optional)
POWER
Sensor: 4 x AA alkaline or lithium batteries
DATA REPORTING
Wind Speed: 18 second updates; Direction: 36 seconds
Outdoor temperature & humidity: 36 second updates
Indoor temperature & humidity: 60 second updates
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
18
Customer Support
AcuRite customer support is committed to providing you with best-inclass service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(262) 729-4852
Visit us at www.AcuRite.com
► Installation
Videos
► Register
your Product
► Instruction
Manuals
► Support
User Forum
► Replacement
Parts
► Submit
IMPORTANT
Feedback & Ideas
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 yearwarranty protection
www.AcuRite.com
Limited 1-Year Warranty
AcuRite is a wholly owned subsidiary of Chaney
Instrument Company. For purchases of AcuRite
products, AcuRite provides the benefits and services set
forth herein. For purchases of Chaney products, Chaney
provides the benefits and services set forth herein.
We warrant that all products we manufacture under this
warranty are of good material and workmanship and, when
properly installed and operated, will be free of defects for a
period of one year from the date of purchase.
Any product which, under normal use and service, is proven
to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by us, and at our sole
option, be repaired or replaced by us. Transportation costs and
charges for returned goods shall be paid for by the purchaser.
We hereby disclaim all responsibility for such transportation
costs and charges. This warranty will not be breached, and we
will give no credit for products which have received normal
wear and tear not affecting the functionality of the product,
been damaged (including by acts of nature), tampered,
abused, improperly installed, or repaired or altered by others
than our authorized representatives.
We expressly disclaim all liability for special, consequential,
or incidental damages, whether arising in tort or by contract
from any breach of this warranty. Some states do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
We further disclaim liability from personal injury relating to
our products to the extent permitted by law. By acceptance of
any of our products, the purchaser assumes all liability for the
consequences arising from their use or misuse. No person, firm
or corporation is authorized to bind us to any other obligation
or liability in connection with the sale of our products.
Furthermore, no person, firm or corporation is authorized
to modify or waive the terms of this warranty unless done in
writing and signed by a duly authorized agent of ours.
In no case shall our liability for any claim relating to our
products, your purchase or your use thereof, exceed the
original purchase price paid for the product.
Applicability of Policy
This Return, Refund, and Warranty Policy applies only to
purchases made in the United States and Canada. For
purchases made in a country other than the United States or
Canada, please consult the policies applicable to the country in
which you made your purchase.
Remedy for breach of this warranty is limited to repair or
replacement of the defective item(s). If we determine that repair
or replacement is not feasible, we may, at our option, refund
the amount of the original purchase price.
Additionally, this Policy applies only to the original purchaser
of our products. We cannot and do not offer any return,
refund, or warranty services if you buy products used or from
resale sites such as eBay or Craigslist.
THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY
FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES
OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN
ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
Governing Law
This Return, Refund, and Warranty Policy is governed by the
laws of the United States and the State of Wisconsin. Any
dispute relating to this Policy shall be brought exclusively in the
federal or State courts having jurisdiction in Walworth County,
Wisconsin; and purchaser consents to jurisdiction within the
State of Wisconsin.
19
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
It’s More than Accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
Printed in China
01141 INST 011618
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of
the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology.
Visit www.AcuRite.com/patents for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising