Groen | DHT | Spec sheet | Groen DHT Spec Sheet

Groen DHT Spec Sheet
PROJECT NAME:
LOCATION:
COOKER/MIXERS
ITEM NO:
FLOOR MOUNTED INCLINED AGITATOR GAS MODEL DHT
Cooker/Mixer shall be a Groen Model DHT-40 or 60(C,A), INA/2 gallon (specify 40- or 60-gallon) stainless steel,
self-contained, 2/3 steam jacketed unit operating from a gas heated steam source contained within unit and
complete with console mounted tilt out inclined agitator mixer.
QTY:
MODEL NO:
AIA NO:
SIS NO:
AVAILABLE MODELS:
DHT-40C INA/2 (40 GALLON)
DHT-40A INA/2 (40 GALLON)
DHT-60C INA/2 (60 GALLON)
DHT-60A INA/2 (60 GALLON)
CONSTRUCTION: Kettle interior shall be of 316
stainless steel, solid one-piece welded construction.
The control console and kettle exterior shall be 304
stainless steel. The kettle body shall be mounted on a
heavy duty stainless steel, combination kettle support
tilt trunnion which is supported by the polished stainless
steel enclosed base. The kettle shall be furnished with
heavy duty reinforced rim with a butterfly shaped pouring
lip for maximum sanitation and ease of pouring. The
base shall be provided with stainless steel tubular legs
with adjustable flanged feet. The enclosed support
base shall contain a self-locking worm and gear tilt
mechanism, controls, etc., and shall be of sanitary
drip-proof construction with interior readily accessible
for installation or maintenance. Unit includes 2” TDO,
5-gallon etch markings and faucet mounting bracket.
FINISH: Interior of kettle shall be polished to a 180
emery grit finish. Exterior of kettle shall be finished to
a bright semi-deluxe finish, ensuring maximum ease in
cleaning and maintaining brilliant appearance.
AGITATOR ASSEMBLY: Agitator assembly to
be designed to thoroughly fold and blend product with
gentle lifting action provided by agitator entering kettle
body at an angle. Inclined agitator to be stainless steel
tubular frame, complete with shovel-type scrapers.
Agitator to be readily removable for ease of cleaning and
maximum sanitation. Unit driven by a gear motor through
an electronic variable speed control. Motor is completely
enclosed-type with a cast iron housing, helical bevel
gearing and right angle shaft down. Motor drive is
mounted on a stainless steel channel that manually
hinges out to the right side of kettle. Unit to be equipped
with a spring assist for agitator tilt-out. A positive quickacting lock and latch mechanism to be provided to
secure the agitator when it is in the kettle.
ASME CODE & UL LISTING: Unit shall be
ASME shop inspected, stamped and registered with
the National Board for operation up to a maximum
working pressure of 50 PSI. Kettle is UL listed. Kettle
shall be design certified by CSA America for use with
natural gas or LP gas.
SANITATION: Unit shall be designed and
constructed to meet NSF requirements, and be NSF
listed.
SELF CONTAINED STEAM SOURCE:
Kettle shall have a gas heated (natural or propane)
self-contained steam source to provide kettle
temperatures of 150°F to approximately 295°F. Unit
shall be factory charged with water and rust inhibitors
to ensure long life and minimum maintenance.
CONTROLS: Controls to be located in right-side
water resistant (IPX6 rated) trunnion enclosure:
Classic -C Models include: Power ON-OFF switch
with indicator light, temperature control knob with
1 to 10 increments, HEAT(ing) indicator light and
LOW WATER warning light. Advanced -A Models
include: Power ON-OFF switch with indicator light,
temperature & time set knob, HEAT(ing) indicator
light, LED display of set heat level or cook time,
buttons for reset of Low Temp and High Temp
presets, MANUAL mode button for knob-setting of
heat level, and TIMER set button with indicator light.
The agitator has on-off and variable speed control
switch.
OPTIONS/ACCESSORIES:
Disk strainers (not to be used
with agitator)
240, 480 Volt power supply (for
agitator motor)
Kettle brush kit
Pan carrier
Gallon master
Basket insert
Lip strainers
Contour measuring strips
SAFETY FEATURES: Kettle shall have safety
cut-off (cuts off heat when tilted to an angle above
10 degrees), pressure relief valve, high limit pressure
switch and low water cut off, 24V control system, and
agitator safety tilt cut off.
INSTALLATION REQUIREMENTS: Specify
natural or propane gas. Unit requires 1/2” NPT gas
line connection, 115 volt, 60Hz power for kettle and
208 volt (3-phase only) power for agitator motor. No
remote steam source required.
ORIGIN OF MANUFACTURE: Designed and
manufactured in the United States.
Cooker/Mixers
176859 RevA
Revised 08/18
DHT
P/N 176805 REV A
888-994-7636, unifiedbrands.net
© 2018 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising