Groen | DHT | Spec sheet | Groen DHT Spec Sheet

Groen DHT Spec Sheet
PROJECT NAME:
LOCATION:
COOKER/MIXERS
ITEM NO:
FLOOR MOUNTED TWIN SHAFT AGITATOR GAS MODEL DHT
Cooker/Mixer Kettle shall be a Groen Model DHT-40 or 60 (C,A), TA/3 (specify 40- or 60-gallon) stainless
steel, self contained 2/3 steam jacketed unit operating from a gas-heated steam source contained within unit,
complete with console-mounted tilt-out twin shaft scraper mixer.
QTY:
MODEL NO:
AIA NO:
SIS NO:
AVAILABLE MODELS:
DHT-40C TA/3 (40 GALLON)
DHT-40A TA/3 (40 GALLON)
DHT-60C TA/3 (60 GALLON)
DHT-60A TA/3 (60 GALLON)
CONSTRUCTION: Kettle interior shall be of type
316 stainless steel, solid one-piece welded construction.
The control console and kettle exterior shall be 304
stainless steel. The kettle body shall be mounted on a
heavy-duty stainless steel, combination kettle support tilt
trunnion, which, is supported by the polished stainless
steel enclosed base. The kettle shall be furnished with
heavy-duty reinforced rim with a butterfly-shaped
pouring lip for maximum sanitation and ease of pouring.
The base shall be provided with stainless steel tubular
legs with adjustable bullet feet. The enclosed support
base shall contain a self-locking worm and gear tilt
mechanism, controls, etc., and shall be of sanitary,
drip-proof construction with interior readily accessible
for installation or maintenance. Unit includes 2” TDO,
10-Gallon etch markings and double pantry faucet.
AGITATOR ASSEMBLY: Enclosed transfer case
to be cast aluminum with a 3- to-1 gear ratio. Gear
motor to be completely enclosed-type, cast iron housing,
right angle shaft down, helical bevel gearing, variablespeed motor driven through an electronic speed control.
See table on back for minimum and maximum agitator
speeds. Main agitator to be anchor type, shaped to the
contour of the kettle and provided with removable nylon
finger scrapers. The secondary counter-rotating bar type
agitator shall be centrally-located between the center
shaft and the outside arms of the main agitator. Both
agitators are attached with bayonet connections for easy,
quick removal for cleaning or when kettle is to be used
without the mixing mechanism. Both agitators are 304
stainless steel and either can be used alone. Agitator and
motor drive assembly can be manually tilted to the right
side of the kettle.
FINISH: Kettle interior shall be polished to a 180
emery grit finish. Kettle exterior shall be finished to a
bright semi-delux finish, ensuring maximum ease in
cleaning and maintaining brilliant appearance.
ASME CODE AND CSA
CERTIFICATION: Unit shall be ASME shop-
inspected, stamped and registered with the National
Board for operation up to a maximum working
pressure of 50 PSIG. Kettle shall be design certified
by CSA America for use with natural gas or LP gas.
SANITATION: Unit shall be designed and
constructed to be NSF listed, meeting NSF
requirements.
SELF-CONTAINED STEAM SOURCE:
Kettle shall have an gas-heated (natural or
propane), self-contained steam source to provide
kettle temperatures of 150°F to approximately
295°F. Unit shall be factory-charged with water
and rust inhibitors to ensure long life and minimum
maintenance.
OPTIONS/ACCESSORIES:
Disk Strainers (Not to be used
with agitator)
240, 480 Volt Power Supply
Kettle Brush Kit
Pan Carrier
Gallon Master
Basket Insert
Lip strainers
Contour measuring strips
CONTROLS: Controls to be located in right-side
water resistant (IPX6 rated) trunnion enclosure:
Classic -C Models include: Power ON-OFF switch
with indicator light, temperature control knob with 1
to 10 increments, HEAT(ing) indicator light and LOW
WATER warning light. Advanced -A Models include:
Power ON-OFF switch with indicator light, temperature
& time set knob, HEAT(ing) indicator light, LED display
of set heat level or cook time, buttons for reset of Low
Temp and High Temp presets, MANUAL mode button
for knob-setting of heat level, and TIMER set button
with indicator light. The agitator has on-off and variable
speed control switch.
SAFETY FEATURES: Kettle shall have safety
cut-off (turns off heat when tilted to an angle above
10 degrees), pressure relief valve, high limit pressure
switch and low water cut-off, 24Volt control system
and agitator safety tilt cut-off.
INSTALLATION REQUIREMENTS: Specify
natural or propane gas. Unit requires 1/2 “ NPT gas
line connection, 115Volt, 60Hz power for kettle and
208 Volt (3-phase only) power for agitator motor. No
remote steam source required.
ORIGIN OF MANUFACTURE: Designed and
manufactured in the United States.
Cooker/Mixers
176860 RevA
Revised 08/18
DHT
P/N 176806 REV A
888-994-7636, unifiedbrands.net
© 2018 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising