Groen | Caster Kit | Installation instructions | Groen Caster Kit Installation Instructions

Groen Caster Kit Installation Instructions
PART NUMBER 150528, REV. D (11/18)
This manual provides information for:
OPERATOR MANUAL
IMPORTANT INFORMATION, KEEP FOR OPERATOR
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, fax 888-864-7636
unifiedbrands.net
CASTER KIT INSTALLATION
The following instructions are applicable to the flanged feet kits supplied as optional equipment for Groen Braising Pans; Groen Steamers:
Vortex100™, SmartSteam100™, HyPerSteam™, and Intek™; Groen
ComboEase™ Steamer/Ovens; and small kettles/small braising pan
mounted on Groen TS/10 Stands.
OPERATORS AND INSTALLATION TECHNICIANS SHOULD READ, UNDERSTAND
AND FOLLOW ALL WARNINGS AND INSTRUCTIONS PROVIDED IN THIS SHEET.
THE RESTRAINING DEVICE MUST ALWAYS BE CONNECTED WHEN THE APPLIANCE WITH
CASTERS IS IN SERVICE.
NOTIFY CARRIER OF DAMAGE AT ONCE It is the responsibility of the
consignee to inspect the container upon receipt of same and to determine
the possibility of any damage, including concealed damage. Unified
Brands suggests that if you are suspicious of damage to make a notation
on the delivery receipt. It will be the responsibility of the consignee to file
a claim with the carrier. We recommend that you do so at once.
DISCONNECT, THEN RECONNECT – ONLY FOR MAINTENANCE
A RESTRAINING DEVICE IS REQUIRED FOR ALL UNITS WITH CASTERS PER EITHER OF
THE FOLLOWING STANDARDS: UL/ANS1 197, ANSI Z83.11/CSA 1.8
Manufacture Service/Questions 888-994-7636.
146354 KIT FOR BPM AND BPP MODELS,
ELECTRIC OR GAS, AND TS/10 STANDS
WARNING: WHEN INSTALLING A RESTRAINING CABLE ON A GAS BRAISING PAN
EQUIPPED WITH CASTERS, THE GAS QUICK-DISCONNECT SUPPLY HOSE
OR THE PERMANENTLY CONNECTED FLEXIBLE SUPPLY HOSE MUST BE
LONGER THAN THE RESTRAINT CABLE USED TO SECURE THE BRAISING
PAN.
WHEN INSTALLING A RESTRAINING CABLE ON AN ELECTRIC BRAISING PAN
EQUIPPED WITH CASTERS, THE LENGTH OF THE FLEXIBLE ELECTRICAL
CONDUIT MUST BE LONGER THAN THE RESTRAINT CABLE USED TO
SECURE THE BRAISING PAN.
1. Raise the Braising Pan about 8” above the floor.
2. Unscrew the installed bullet feet adapters from the four legs of the Braising Pan.
3. Screw the two locking casters into the front legs of the Braising Pan and
screw the two non-locking casters into the rear legs of the Braising Pan.
4. Level the Braising Pan front-to-back and left-to-right by adjusting the
amount the casters screw into the legs.
FIGURE 1
FIGURE 2
5. Anchor the restraining cable bracket to a secure structure (typically the wall
or the floor). One of the preferred locations is on a concrete floor near the
braising pan using anchor bolts (installer provided) as shown in Figure 1.
6. Install the label (P/N 170036) included in the restraining cable kit as shown
in Figure 2.
7. Connect the clip on the restraining cable to the hole in the rear of the
braising pan stand frame as shown in Figure 3.
8. The completed assembly should appear as shown in Figure 4.
9. After installation, pull out the braising pan to the full length of the restraining
cable and verify that the gas hose or electrical conduit are not under tension
or stretched.
FIGURE 3
FIGURE 4
Information contained in this document is known to be current and accurate at the time of printing/creation. Unified Brands recommends referencing our product line websites, unifiedbrands.net,
for the most updated product information and specifications. © 2018 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
098611 KIT FOR VORTEX100, SMARTSTEAM100,
HYPERSTEAM, AND INTEK STEAMER STANDS
CAUTION: DO NOT INSTALL CASTERS ON HY-PLUS MODEL
WARNING: WHEN INSTALLING A RESTRAINING CABLE ON A GAS STEAMER STAND
EQUIPPED WITH CASTERS, THE GAS QUICK-DISCONNECT SUPPLY HOSE
OR THE PERMANENTLY CONNECTED FLEXIBLE SUPPLY HOSE MUST BE
LONGER THAN THE RESTRAINT CABLE USED TO SECURE THE STEAMER.
13/32” (9mm) hole
for Clip Restraint
WHEN INSTALLING A RESTRAINING CABLE ON AN ELECTRIC STEAMER
STAND EQUIPPED WITH CASTERS, THE LENGTH OF THE FLEXIBLE
ELECTRICAL CONDUIT MUST BE LONGER THAN THE RESTRAINT CABLE
USED TO SECURE THE STEAMER.
Drill 13/32”
(9mm) hole
CAUTION: DO NOT TILT THE STEAMER AND INSTALL (2) CASTERS, THEN TILT TO THE
OTHER SIDE TO INSTALL THE LAST PAIR THIS WILL DAMAGE THE STAND
WARNING: SUPPORT THE STEAMER AND STAND SECURELY BEFORE LIFTING SO THAT
IT DOES NOT TIP OVER DURING INSTALLATION.
NOTE: THE RESTRAINING CABLE KIT (PART NUMBER 150518) IS NOT SUPPLIED
WITH THE CASTER KIT. IT IS INCLUDED IN THE 140144 QUICK-DISCONNECT
GAS HOSE KIT. WHEN INSTALLING GAS UNITS WITH FLEXIBLE GAS HOSE
OR ELECTRICAL UNITS WITH FLEXIBLE CONDUIT, ORDER THE CABLE KIT
SEPARATELY.
1. On Steamer(s), all four legs must be raised at the same time to properly
install casters.
FIGURE 6 (STAND FOR STEAMER)
Eyebolt and
flat washer
2. Remove the four bullet foot inserts from the stand legs. They are force-fit
into the ends of the legs and can be driven out with a small hammer and a
screwdriver.
Flat washer,
split lock
washer, and
hex nut
3. Insert the locking casters into the two front legs of the stand and the nonlocking casters into the two rear legs of the stand. Be sure compression
sleeve washer is snuggly held to stand leg. They are fitted with a rubber
compression sleeve and a hex head bolt on the underside between the
sleeve and the wheel that is tightened to secure the caster within the leg, as
indicated in Figure 5.
FIGURE 7
FIGURE 8
4. Drill a 13/32” (or 9 mm) diameter hole through one of the rear legs of the
steamer stand approximately 3” to 6” below the top of the stand as shown
in Figure 6.
5. Attach the eyebolt to the stand leg using the washers and nut included in the
restraining cable kit, as shown in Figure 7.
6. Anchor the restraining cable bracket to a secure structure (typically the wall
or the floor). One of the preferred locations is on a concrete floor near the
braising pan using anchor bolts (installer provided) as shown in Figure 1 on
previous page.
7. Install the label (P/N 170036) included in the restraining cable kit as shown
in Figure 8. The label must be installed adjacent to the restraining cable
eyebolt.
8. Attach the restraining cable clip to the eye of the eyebolt, as shown in Figure 9.
9. After installation, pull out the steamer to the full length of the restraining
cable and verify that the gas hose or electrical conduit are not under
tension or stretched.
FIGURE 9
FIGURE 10
150518 RESTRAINING KIT FOR COMBOEASE STANDS
WARNING: COMBOEASE STEAMER/OVENS COME FACTORY-EQUIPPED WITH CASTERS,
THE GAS QUICK-DISCONNECT SUPPLY HOSE OR THE PERMANENTLY
CONNECTED FLEXIBLE SUPPLY HOSE MUST BE LONGER THAN THE
RESTRAINT CABLE USED TO SECURE THE COMBOEASE.
1. Anchor the restraining cable bracket to a secure structure (typically the wall
or the floor). One of the preferred locations is on a concrete floor near the
braising pan using anchor bolts (installer provided) as shown in Figure 10.
2. Attach the restraining cable clip to the eye of the factory-installed eyebolt on
the lower left rear of the ComboEase.
Hex Head for
Adjustment
Hex Head for
Adjustment
3. After installation, pull out the ComboEase to the full length of the restraining
cable and verify that the gas hose is not under tension or stretched.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising