Power Soak | PSU3 | Spec sheet | Power Soak PSU3 Spec Sheet

Power Soak PSU3 Spec Sheet
PROJECT NAME:
LOCATION:
ITEM NO:
POWER SOAK SYSTEM
QTY:
UNLIMITED CONTINUOUS POT, PAN & SHEET PAN WASHING
SYSTEM WITH 3” SPACED WASH JETS, MODEL PSU3
The Power Soak Advanced System is a three-bay continuous pot, pan and sheet washing system with custom
configured lengths and options. The patented Parallel Wash System’s washing wave action, with wash jets
located every 3 inches along the back wall of the wash tank, continuously rotates wares from the back of the
wash tank up to the operator in hot soapy water that removes baked-on food soils, providing unparalleled
results with an excellent ROI.
STANDARD SPECIFICATIONS:
• System custom configurable per quote or drawing
• Available left to right or right to left operation, 34” or
37” front to back depth
• All tanks and tabling, 14 gauge, 304 stainless steel
• System conforms to ANSI/NSF Standard 2 with all
welds to be heliarc (TIG) welds
• Backsplash to be 9.5” overall height - 6” vertical with
45 degree angle to wall with 1-½” turn up
• Wash tank shall be 28.75” or 31.75” I.D standard
front to back to back by 21” deep, 30” - 72” in
length (increasing/decreasing in 6” increments)
• Parallel Wash Flow with low profile wash jets spaced
every 3” flush along the back wall of wash tank &
above the wash pump intake
• 2 HP Wash Pump Motor (30 & 36” Tank) or 3 HP
Wash Pump Motor (42 & 48” Tank) with stainless
steel impeller, pump housing and wash manifold
• Stainless steel wash pump intake to run full length of
the rear of the wash tank below wash jets
• Stainless steel wash pump housing fully self-draining
with no use of drain line or valve
• Wash Tank to have Advanced Wash Insert (AWI)
– consisting of (1) ultra-high molecular weight
polyethylene (UHMW) flexible tank divider, or (2) with
sheet pan racks, (UHMW) wash tank flow guides,
high density polyethylene (HDPE) rib system integrally
connected with sst rods and 1/8” thick UHMW tank
liner form fitting to bottom of wash tank
• Utensil Section to be powered by one dedicated
wash jet
• Dual liquid high & low water level sensors
• Bottom of wash tank creased to facilitate draining
• 7000 watt wash tank heater maintains wash tank
temperature at 115˚ +/- ½ ˚F
• Chemical injection points pre-drilled at factory
• Rinse Sink and Sanitizer Sink each shall be 28.75” or
31.75” I.D. front to back
• Soiled tabling custom configurable incorporating
various pre-scrapping systems: i.e.: scrap sinks,
disposers, collectors, pulpers or custom design
scarping areas
• Drains & faucets included, but optional
MODEL NO:
AIA NO:
SIS NO:
CSI SECTION:
11400
CONTROLS:
PS-200: Timed wash cycle, wash tank heat,
sanitizer tank cycle monitoring. All controls include
at minimum:
• Four hour wash timer
• Low voltage power is supplied to all operator
controls and sensors
• Operator controls - Green (ON)/Red (OFF)
buttons
• Automatically monitors and regulates wash
water temp
• Monitors high and low liquid levels in both
the wash tank and sanitizer tank
• Meets UL 50, category 4X specifications
PS-225: All PS-200 features included plus
adjustable sanitizer tank cycle monitoring, batch
washing, non-intrusive function lights (see
Control Specification for more detailed features)
PS-275: All PS-225 features included plus
overnight wash cycle (see Control Specification
for more detailed features)
INSTALLATION REQUIREMENTS:
• Unit requires hot and cold water connections
• Drain connections
• Single point electrical connection
WARRANTY:
3 years for parts and labor
ORIGIN OF MANUFACTURE:
Designed and manufactured in the United States.
Power Soak System
45476 RevB
Revised 04/24/19
PSU3
INTERNATIONAL 50 HZ:
WASH TANK SIZES 30”, 36”, 42”,
48” – 2 HP MOTOR (6.4 KW WASH
TANK HEATER)
220V/50/1 – 38.6 Amps
WASH TANK SIZES 30”, 36”, 42”,
48” – 2 HP MOTOR (7 KW WASH
TANK HEATER)
380V/50/3 – 15.4 Amps
98"
1”
-
12” 42" x 21” 14” x 18” 14” x 18”
14”
1”
132"
1”
12”
12” 48" x 21” 20” x 14” 20” x 14”
18”
1”
Rinse Tank
End Splash
Sanitzer Tank
Length
Clean Drain
Board
racks (18’’ x 26” sheet pans)
– 2, 6 & 10 sheet pan racks (available only for 37” front to
back system)
Hemmed end splash
1” end splash
Channel end splash
Backsplash end splash
Filled end splash
Channel front rim
Rolled front rim
Turned up back splash
Turned down back splash
with “z” clips
Back splash extensions
Up to 21” rinse or sanitizer
tank in depth
Welded field joint
Mechanical filed joint (JBZ)
Welded leg sets
Advanced Wash Insert (AWI)
Advanced Wash Insert (AWI)
– sheet pan rack system
(available only for 37” front to
back system)
Under shelfs
Over shelfs
Automatic chemical dispenser
2.5 kw wash tank heater
(7kw – standard)
Remote silent alert for PS225 & PS-275 controls
Quick disconnect pre-rinse
sprayers
Electrical disconnect
Sanitizer tank accommodation
for 180 degree recirculating
hot water booster
Mixing valves
Drying racks for clean drain
board
Overflows for rinse and/or
sanitizer tank
Wash Tank
Advanced wash sheet pan
Scrap Sink
DOMESTIC 60HZ:
WASH TANK SIZES 30”, 36”, 42”,
48” – 2 HP MOTOR (7 KW WASH
TANK HEATER)
208V/60/1, 45.1 Amps
208V/60/3, 26.7 Amps
230V/60/1, 39.8 Amps
230V/60/3, 24.0 Amps
480V/60/3, 11.6 Amps
BELOW CHART SHOWS A SAMPLE CONFIGURATION
OF UNIT FROM LEFT TO RIGHT
Soiled Drain
Board
CONFIGURATION &
ACCESSORY OPTIONS:
End Splash
ELECTRICAL
CONNECTION OPTIONS:
888-994-7636, unifiedbrands.net
© 2019 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
PSU3
SAMPLE CONFIGURATION:
888-994-7636, unifiedbrands.net
© 2019 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
PSU3
SAMPLE CONFIGURATION:
888-994-7636, unifiedbrands.net
© 2019 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising