Z-Wave VRR15-1LZ Installation guide

Z-Wave VRR15-1LZ Installation guide
Duplex Receptacle (Top Controlled)
Scene Capable Receptacle
Cat. No. VRR15-1L - 15A - 125VAC, 60Hz
Incandescent-1800W – Magnetic Low-Voltage-1800VA (1440W)
Electronic Low-Voltage-1800W – Fluorescent-1800VA – Supplemental-1/2 HP
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• To ensure that there is adequate room for wires, we recommend using at a minimum 3-1/2 inch deep wallboxes. For single-gang applications, this would be at a
minimum an 18-cubic inch wallbox.
Changing the color of your Receptacle:
INTRODUCTION
Leviton’s Vizia RF +™ Z-Wave components are designed to communicate
with each other via Radio Frequency (RF) to provide remote control of
your lighting. Using RF technology allows Leviton to provide the greatest
signal integrity possible. Each module in Leviton’s Vizia RF +™ component
line is a Z-Wave® enabled device. In a Z-Wave® network, each device is
designed to act as a router. These routers will re-transmit the RF signal
from one device to another until the intended device is reached. This
ensures that the signal is received by its intended device by routing
the signal around obstacles and radio dead spots. The Scene Capable
Electronic Receptacle is compatible with most Z-Wave® enabled networks,
from different manufacturers and can also be used with other devices
displaying the Z-Wave® logo.
®
CAUTION:
Remember to exercise good common sense when using the Timer features
of your Remote – especially when scheduling unattended devices. There
can be some unexpected consequences if not used with care. For example,
an empty coffee pot can be remotely turned on. If that should happen,
your coffee pot could be damaged from overheating. If an electric heater
is turned on by remote control while clothing is draped over it, a fire could
result. DO NOT USE the remote for the control of high power heating
appliances such as portable heaters.
Your Receptacle includes three color options. The Receptacle ships with the
White frame attached. To change color of frame, proceed as follows:
WARNINGS AND CAUTIONS:
• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
• Maximum wire length cannot exceed 300 ft (90 m).
• Use this device with copper or copper clad wire only.
Step 3 Preparing and connecting wires:
This receptacle can be wired using side wire terminal screws or
through backwire openings. Choose appropriate wire stripping
specifications accordingly.
Cut
(if necessary)
Push in side
at tab to release
INSTALLING YOUR RECEPTACLE
NOTE: Use check boxes
Step 1
•
•
•
•
•
•
•
Receptacle ON/OFF
Scene Capable
ON/OFF LED
Two way communication
RF reliability
Ease of installation – No new wiring
Compatible with other Z-Wave® enabled devices
when Steps are completed.
WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN
OFF POWER at circuit breaker or fuse and test that power is off
before wiring!
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Side Wire Connection
Back Wire (either hole may be used)
Side wire terminals accept #14-12 Back wire openings accept #14-12
AWG solid copper wire only.
AWG solid copper wire only.
• Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
• Remove insulation from each wire in the wall box as shown.
OFF
ON
OFF
ON
Electrical Tape
Cutters
Step 6 Receptacle Mounting:
CONTROLLED
Line (Black)
NOTE: If the wiring in your wall box does not resemble any of
these configurations, consult a qualified electrician.
1
3
4
• Restore power at circuit breaker or fuse.
• Locator light should turn ON.
If locator light does not turn ON, refer to the TROUBLESHOOTING
section.
Single Pole Wiring Application:
Neutral (Silver)
Step 2 Identifying your wiring application (most common):
Pliers
Ruler
• Position all wires to provide room in outlet wall box for device.
• Partially screw in mounting screws in wall box mounting holes.
NOTE: Dress wires with a bend as shown in diagram in order to
relieve stress when mounting device.
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Tools needed to install your Receptacle
Slotted/Phillips Screwdriver
Pencil
Strip Gage
(measure bare
wire here)
Line up tabs and
press in sides one at a time
to attach
Step 4
FEATURES
5/8"
(1.6 cm)
Step 5 Testing your Receptacle prior to mounting in
wall box:
2
Green
Ground
Single Pole
1. Line (Hot)
2. Neutral
3. Ground
CONTROLLED
Installation may now be completed by tightening
mounting screws into wall box. Attach wallplate.
Step 7 Restore Power:
WIRING RECEPTACLE:
Connect wires per WIRING DIAGRAM as follows:
•
•
•
•
Restore power at circuit breaker or fuse.
Installation is complete.
Green or bare copper wire in wall box to Green terminal screw.
Line Hot wall box wire to terminal screw marked "LINE".
Line Neutral wall box wire to terminal screw marked "NEUTRAL".
Proceed to Step 5.
DI-000-VRR15-02A
®
Step 8 Including Receptacle into Z-Wave Network:
NOTES:
•
Receptacle will be included as a switch
•
If using a non-Leviton Programmer/Controller, refer to the
Programmer/Controller instruction sheet for Including a device.
•
If using VRCPG install checklist go directly to step B.
A) If using a Leviton Z-Wave® Programmer/Controller, Cat. No. VRCPG,
press the Menu button and scroll down to System. Press the center
button to select System Menu. Choose Advanced. Press the center
button to select Advance Install.
B) While standing close to the receptacle (approximately 1 foot), press
the center button to <Include> device in the network.
NOTE: Only one device may be included at a time. DO NOT put
multiple devices into the Inclusion mode at any time.
C) While the Programmer/Controller is in the Inclusion mode and
the Locator LED is ON on the receptacle, press the button on the
receptacle. The Programmer/Controller will verify inclusion.
If the receptacle is flashing Amber while in the Inclusion mode,
the Programmer/Controller is still trying to communicate with the
receptacle. Wait until the device stops flashing, then press the
receptacle program button.
NOTE: If the Locator LED on the receptacle turns solid Red
while including, there has been a communication error. Refer to
Troubleshooting section.
D) The Primary Programmer/Controller will assign a node ID number
(Name) for this device.
NOTE: This ID number (Name) will be stored in the controller to be
used for future reference.
NOTE: You may name or edit your device at this time.
E) The receptacle is now installed in the network.
NOTE: If the receptacle has been
Programmer/Controller
successfully Included in the network and
Cat. No. VRCPG
the user tries to Include it again without first
excluding it from the network, the receptacle
will retain the first node ID it had received
and ignore the second.
Menu
Button
1 ON
OFF
2 ON
OFF
3 ON
OFF
4 ON
OFF
Center
Button
Step 9
Excluding Receptacle from Z-Wave® Network:
NOTE: It is very important to accurately Exclude devices from the network
when moving or removing a device from a Z-Wave® network. This ensures
that all information has been removed from your Primary.
A) If using a Leviton Z-Wave® Programmer/Controller, Cat. No. VRCPG,
press the Menu button and scroll down to System. Press the center
button to select. Choose Advanced. Press the center button to select
Advanced Install. Scroll down to exclude.
B) While standing close to the receptacle (approximately 1 foot), press the
center button to <Exclude> device from the network.
C) While the Programmer/Controller is in the Exclusion mode and the
locator LED is ON press the button. The Programmer/Controller will
verify Exclusion and the locator LED will turn OFF.
If the receptacle is flashing Amber while in the Exclusion mode, the
Programmer/Controller is still trying to communicate with the receptacle.
Wait until the device stops flashing, then press the receptacle program
button.
Factory Default:
If your receptacle is not responding, or you are unable to control it after you
have tried to Include/Exclude it multiple times, it may be necessary to reset
the receptacle to its original factory settings. To accomplish this, proceed as
follows:
• On the receptacle, press and hold the program button until the locator
LED turns Amber and then flashes Red. The receptacle is now reset.
Once the receptacle is reset, it will be necessary to Re-Include it to a
network before it can be used.
CAUTION: SETTING A DEVICE TO A FACTORY DEFAULT DOES
NOT EXCLUDE THAT DEVICE FROM A NETWORK. THE EXCLUSION
PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE
FROM THE PRIMARY CONTROLLER’S INFORMATION TABLE. FAILURE
TO DO SO MAY RESULT IN SYSTEM THAT IS SLOW TO RESPOND, OR
MAY FAIL TO RESPOND TO SOME DEVICES.
FCC COMPLIANCE STATEMENT
OPERATION
NOTE: The locator light will illuminate when receptacle is connected.
If there is a power outage, when the power is restored, the lights will return
to the last setting before the power interruption.
Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.
Locator
Light
CONTROLLED
Programming
button
TROUBLESHOOTING
• Receptacle has no power
- Receptacle has a bad connection.
-Wires not secured firmly under terminal screws of receptacle.
• Locator LED does not turn ON
- Circuit breaker or fuse has tripped.
- Neutral connection is not wired.
- Press progarmming button.
This device complies with Part 15 of the FCC Rules. Operation is subject
to following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for
a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving Antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/tv technician for help.
FCC CAUTION
Any changes or modifications not expressly approved by Leviton
Manufacturing Co., Inc., could void the user's authority to operate the
equipment.
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.ViziaRFplus.com
Gently press
Programming button
Protected under U.S. Patent Number 6,388,399 and patents pending
and licensed under U.S. Patents Numbers 5,905,442, and 5,982,103
Programmer/Controller
Cat. No. VRCPG
NOTE: Programmer/Controller must be in close
proximity to receptacle when including in the network.
© 2009 Leviton Mfg. Co., Inc.
DI-000-VRR15-02A
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement,
at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor
for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied
warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement