Optex 750830 Owner's Manual
The Optex 750830 utilizes advanced wireless audio and video transmission and can convey quality audio and video signals up to a distance of 300ft. The product implements frequency hopping spread spectrum technology that changes frequencies on the fly to avoid any interference within the 2.4GHz range. Extremely low latency of only 4ms allows the remote transmission of signals in real-time. Optex 750830 offers many possible applications but will be especially useful in video surveillance as well as multimedia home entertainment systems. The product comes with a user manual and 1-year warranty.
Advertisement
Advertisement
avec extension infra-rouge
REF : 750830
www.optex.fr
PRECAUTIONS D’UTILISATION
• Pour prévenir du feu, ne pas exposer le transmetteur à la pluie ou au rayon direct du soleil.
• Pour éviter les chocs électrique, ne pas ouvrir les produits. (Sous peine d’annulation de la garantie)
• Le transmetteur et le récepteur doivent utiliser les transformateurs d’alimentation fournit dans le pack.
• Ne pas surcharger les prises de courant et les cordons d’alimentation cela risquerait d’endommager le matériel.
• En cas de problème, référez-vous à une personne qualifi ée.
Attention : Toutes modifi cations apportées au matériel entraînera la non prise en charge du SAV sous garantie.
Remarque :
Cet équipement a été testé et trouvé conforme aux limites BZT, FCC et la directive CE EMC. Ces limites sont désignées pour assurer une protection raisonnable contre les interférences dans les installations résidentielles.
Cet équipement génère, et peut émettre des fréquences radios : s’il n’est pas installé et utilisé conformément aux instructions, il risque alors de provoquer des interférences dans les communications radios.
Toutefois, il n’est pas garantie que des interférences ne viendront pas perturber une installation de particulier.
Si cet équipement cause des interférences au niveau radio ou de la réception télé, à l’allumage ou
à la mise en veille, l’utilisateur doit corriger ces interférences grâce à une ou plusieurs des mesures décrites ci-dessous :
* Ré-orienter l’antenne du récepteur.
* Augmenter la séparation entre l’équipement et le récepteur.
* Contacter votre revendeur ou un technicien qualifi é pour avoir de l’aide.
AU DEBALLAGE DU PRODUIT
Vous devez trouver :
• 1 transmetteur audio/vidéo
• 1 récepteur audio/vidéo
• 1 cordon péritel/3 RCA pour l’émetteur
• 1 cordon péritel/3 RCA pour le récepteur
• 2 transformateurs d’alimentation
• Cette notice d’utilisation
• 1 report infra-rouge de télécommande
SOMMAIRE
Précautions d’utilisation .............................................................................................................3
A. Introduction au transmetteur Audio/Vidéo……......................................….............................4
B. Descriptions connectique produit...........................................................................................5
C. Fonctionnement du système..................................................................................................6
D. Connexion du transmetteur ...................................................................................................7
Connecter le transmetteur au :
E. Connexion du récepteur ........................................................................................................8
Connecter le récepteur à :
• La télévision ( ou un moniteur vidéo ).................................................................8
F. Connexion avec magnétoscope .............................................................................................9
G. Problèmes possibles, solutions......……….............................................................................10
H. Caractéristiques techniques….…………………………..…………………...............................10
------------------------------------------------
A. INTRODUCTION AU TRANSMETTEUR AUDIO/VIDEO
Ce système est un transmetteur Audio/Vidéo sans fi l qui utilise une technologie de communication avancée pour délivrer un bon son et un signal vidéo à une distance d’environ 100mètres.
La transmission se fait à très haute fréquence (2,4GHz ou 2,4 milliard de cycles par secondes).
Ce système évite la pleine bande de 900MHz utilisée par beaucoups de téléphones sans fi l et d’autres transmetteurs Audio/Vidéo sans fi l.
Cette qualité supérieure est due à l’utilisation de la large bande FM plutôt que la modulation de signal AM.
Les antennes des récepteurs et des émetteurs sont utilisées pour diminuer les interférences non désirées sur le signal et augmenter la portée du signal.
Ce système intègre aussi un déport de télécommande qui vous permet de contrôler la source vidéo ou audio d’une autre chambre en utilisant la télécommande de votre source vidéo.
Application générale
• Regarder une cassette vidéo que vous avez loué sur 2 téléviseurs dans votre maison sans déplacer votre magnétoscope, lecteur DVD….
• Regarder le câble ou des programmes satellites sur 2 téléviseurs dans votre maison.
• Ecouter de la musique de qualité stéréo de votre récepteur (satellite) vers plusieurs hautsparleurs à l’intérieur ou à l’extérieur de la maison.
Application sécurité
• Un moniteur pour voir votre bébé dormir, vos enfants jouer, les personnes âgées...
• Voir qui est derrière votre porte sur la télévision à travers votre caméra.
• Et bien d’autres applications...
Remarque : Le transmetteur permet la visualisation d’une image identique sur le téléviseur
principal ainsi que sur le téléviseur secondaire. (Et non une image différente!)
B. DESCRIPTION CONNECTIQUE PRODUIT
PANNEAU DE CONTROLE ET CARACTERISTIQUES
Ci-dessous, vous verrez des illustrations qui reprennent les noms des différents composants, boutons, connecteurs et switchs de l’émetteur et du récepteur.
Face
Antenne UHF envoi et reçoit le signal de la télécommande.
LED d’alimentation
Switch de sélection de canal utilisé pour une réception optimale. Il est impératif de sélectionner les canaux identiques sur les 2 appareils.
Face arrière du récepteur
Connecteur RCA blanc (Audio gauche)
Switch de sélection de canal utilisé pour une réception optimale. Il est impératif de sélectionner les canaux identiques sur les 2 appareils.
Extension infra-rouge
Connecteur RCA blanc (Audio gauche)
Connecteur RCA rouge (Audio droit)
Face arrière du transmetteur
Connecteur RCA rouge (Audio droit)
Bouton Marche/Arrêt
Connecteur pour le transformateur
Connecteur RCA jaune pour la vidéo
Bouton Marche/Arrêt
Connecteur pour le transformateur
Connecteur RCA jaune pour la vidéo
C. FONCTIONNEMENT DU SYSTEME
Il faut juste connecter l’émetteur à la source Audio/Vidéo que vous voulez renvoyer sur un autre poste, et connecter le récepteur à la prise péritel de votre téléviseur.
Schéma de fonctionnement
Récepteur
Récepteur satellite
OU
Lecteur DVD
OU
2,4GHz audio/vidéo
Camescope
OU
Ordinateur
UHF
OU
Téléviseur
Ordinateur
OU
Chaîne HiFi
Transmetteur
Ce système doit être connecter avec des appareils possédant la fonction A/V :
Sources Vidéo :
• Magnétoscope
• Câble (avec sortie A/V)
• Récepteur satellite
• Lecteur DVD ou CDROM
• Camescope
• Ordinateur
Sources Audio :
• Lecteur de disque compact ou changeur
• Récepteur stéréo
• Lecteur cassette
Les pages suivantes vous montrerons 2 choses :
• comment connecter l’émetteur à plusieurs équipements Audio/Vidéo
• comment connecter le récepteur pour la meilleure position.
D. CONNEXION DU TRANSMETTEUR
Comment transmettre l’Audio et la vidéo à partir du magnétoscope
1. Connecter les 3 câbles de couleur sur l’émetteur et l’extrémité du câble (péritel marqué EMET-
TEUR) vers la prise péritel de votre magnétoscope.
Assurez-vous que les couleurs correspondent bien (jaune avec jaune…) sur l’émetteur.
Si le magnétoscope ne possède qu’une entrée RCA pour l’Audio, alors connecter le câble blanc.
2. Brancher ensuite sur secteur le récepteur grâce au transformateur d’alimentation fournit dans la boîte.
3. Si votre magnétoscope possède une des fi ches RCA, et que vous voulez l’utiliser à proximité de votre téléviseur, connecter un câble coaxial sur la sortie modulateur de votre magnétoscope vers l’entrée VHF/UHF de votre téléviseur.
4. Orienter l’émetteur en suivant les instructions du manuel de façon à obtenir des performances optimales.
Remarque importante :
Vérifi er bien que vous ayez connecté le cordon repéré «RECEPTEUR» sur le boitier récepteur et le cordon repéré «EMETTEUR» sur le boitier émetteur.
Transmetteur
Transformateur d’alimentation
Câble RCA/péritel
magnétoscope
Câble entrée antenne
Câble coaxial 75Ω
Téléviseur
Câble péritel
E. CONNEXION DU RECEPTEUR
Comment recevoir l’audio et la vidéo sans fi l sur votre téléviseur
Il y a 2 façons de recevoir les signaux Audio/Vidéo sans fi l sur un téléviseur éloigné (Dans un endroit différent comme la chambre, la cuisine…)
• Connecter le récepteur directement sur votre téléviseur éloigné.
• Connecter le récepteur au magnétoscope, lequel est alors connecté au téléviseur.
Si votre téléviseur possède l’incrustation vidéo, vous pourrez alors regarder l’image principale et avoir dans le coin de l’écran, une autre image comme celle de votre bébé entrain de dormir…
Consulter le manuel de votre téléviseur pour voir l’utilisation de cette fonction.
Connecter le récepteur directement au téléviseur éloigné
1. Connecter les 3 câbles de couleur sur le récepteur et l’extrémité du câble (péritel marqué RE-
CEPTEUR) vers la prise péritel de votre téléviseur.
Assurez-vous que les couleurs correspondent bien (jaune avec jaune…) sur le récepteur.
Si votre téléviseur ne possède qu’une entrée RCA pour l’Audio, alors connecter le câble blanc.
Remarque importante :
Vérifi er bien que vous ayez connecté le cordon repéré «RECEPTEUR» sur le boitier récepteur.
Récepteur
Vers transformateur d’alimentation
Téléviseur
F. CONNEXION AVEC MAGNETOSCOPE
Connexion du récepteur de la télévision à travers le magnétoscope
Cette procédure vous permet d’enregistrer l’audio et la vidéo de l’émetteur sur votre magnétoscope.
1. Connecter les 3 câbles de couleur sur le récepteur et l’extrémité du câble (péritel marqué RE-
CEPTEUR) vers la prise péritel de votre magnétoscope.
Assurez-vous que les couleurs correspondent bien (jaune avec jaune…) sur le récepteur.
Si le magnétoscope ne possède qu’une entrée RCA pour l’Audio, alors connecter le câble blanc.
2. Brancher ensuite sur secteur le récepteur grâce au transformateur d’alimentation fournit dans la boîte.
3. Si votre magnétoscope possède une des fi ches RCA, et que vous voulez l’utiliser à proximité de votre téléviseur, connecter un câble coaxial sur la sortie modulateur de votre magnétoscope vers l’entrée VHF/UHF de votre téléviseur.
4. Connecter avec un cordon Péritel/Péritel votre téléviseur avec votre magnétoscope.
5. Orienter le récepteur en suivant les instructions du manuel de façon à obtenir des performances optimales.
Récepteur
Transformateur d’alimentation
Câble RCA/péritel
magnétoscope
Câble entrée antenne
Câble coaxial 75Ω
Téléviseur
Câble péritel
G. PROBLEME POSSIBLES, SOLUTIONS...
Lire attentivement le manuel d’utilisation et suivre les étapes décrites. Si vous avez des diffi cultées, consulter le tableau suivant. Il vous donnera les solutions aux problèmes les plus courants.
Problème rencontré
Pas d’image ou pas de son
Interférence : mauvaise image ou mauvais son
La télécommande ne répond pas
Solutions
• Vérifi er les switchs de l’alimentation sur l’émetteur et le récepteur.
• Vérifi er l’alimentation sur les sources vidéos
(DVD, magnétoscope, récepteur satellite, etc...)
• Assurez-vous que les prises d’alimentation sont bien branchées.
• Vérifi er toutes les connexions.
• Ajuster l’orientation de l’antenne récepteur et
émetteur.
• Sélectionner un canal entre1 et 4 sur l’émetteur et le récepteur afi n d’obtenir la meilleure image possible.
• Si vous utilisez un micro-onde, éteignez-le.
• Si un micro-onde est dans la trajectoire de l’émetteur et du récepteur, enlevez-le.
• Vérifi er qu’il n’y ait pas d’obstacles entre l’émetteur et la source vidéo .
H. CARACTERISTIQUES TECHNIQUES
Emetteur :
Niveau de sortie
Bande de fréquence
Modulation
Niveau d’entrée vidéo
Niveau d’entrée audio
Impédance d’entrée vidéo
Impédance d’entrée audio
Consommation
Température
Dimensions
Poids
Récepteur :
Niveau de sortie
Consommation
Fréquence de la télécommande de l’émetteur
Température
Dimensions
Poids
90 dB microvolts/mètre à 3 mètres
2.4 à 2.4835 GHZ
FM (vidéo et audio)
1V p-p @ 75 ohms
2V p-p @ 600 ohms
75 ohms
600 ohms
9 Vdc, 150 mA
0°~50° (intérieur)
17.8 X 12.6 X 6 cm
286g
1 Vp-p @75 ohms (vidéo), 3 volts p-p (audio)
9 Vdc, 280 mA
433.92 MHz (BZT, FCC)
0°~50° (intérieur)
17.8 X 12.6 X 6 cm
312g
Société NORMAND OPTEX
Zone industrielle du Pommier
Boulevard Eugène Thomas
62110 Hénin-Beaumont www.optex.fr
OWNER’S MANUAL
REF : 750830
www.optex.fr
Important-Safety Precautions
To prevent fi re or shock hazard, do not expose this product to rain or moisture. Do not use near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
• To avoid electrical shock, do not open this product.
• This product should be operated using only the power supply included with it or provided as an accessory.
• Do not overload wall outlets and extension cords as this can result in the risk of fi re or electric shock.
• Refer servicing to qualifi ed personnel only.
Caution:
Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for BZT, FCC and CE
EMC directive. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
In the GIFTBOX :
Check to make sure that all of the items shown as below are included with your system. If something is missing, please contact your dealer as soon as possible.
1.Transmitter X 1
2.Receiver X 1
3.Power adapters (230Vac to 9 Vdc 300mA) X 2
4.Audio/Video (RCA to RCA) cable or X 2
Audio/Video (RCA to SCART) cable
5. IR Extender X 1
SUMMARY
A. Introduction to 2.4 GHz Wireless Video Sender......................................…............................15
B. Panel Controls and Features...............................................................................................…16
C. Setting up System...............................................................................................................…17
D. Connecting the System Transmitter to VCR........................................................................…18
E. Connecting the System Receiver to Television ( or Video Monitor )....................................…19
F. Connecting with VCR...........................................................................................................…20
G. Troubleshooting & Care and Maintenance .........................................................................…21
H. Specifi cations & Description of Box Contents ....................................................................... 21
A. Introduction to 2.4 GHz Wireless Video Sender
The system is a wireless audio/video sender that uses advanced wireless communication technology to deliver consistently sharp audio and video up to 100 meters away. By transmitting at a very high frequency (2.4 GHz or 2.4 billion cycles per second), the BZT-compliant The system avoids the crowded 900 MHz band used by many cordless telephones and other wireless audio/video transmitters.
It’s superior quality is due to wide-band FM rather than AM signal modulation.
Circular polarized high-gain directional transmitting and receiving antennas are used to minimize interference from unwanted signals and maximize the signal range.
The system also integrates an UHF remote control extender to allow you to control the audio or video source from another room using your existing remote controller.
General Application
• Watch the movie you rent on any TV in your home without moving you VCR, laser disc player,DVD Player or running messy cables.
• Watch cable or satellite programs on any TV in your home.
• Listen to stereo-quality music from your receiver on any powered speakers inside or outside the home.
• Show computer images on a remote TV (additional equipment required)
Safety & Security Application:
• Monitor your sleeping baby, your playing children, the elderly, or the disabled on your TV using your existing camcorder.
• See who is outside your door on TV through your camera or miniature CCD camera.
• And many more uses!
B. Panel Controls and Features
The following illustrations show the names of each components, button and switch connectors on the transmitter and receiver.
UHF antenna sends and receives remote control signal (Hiding)
FRONT VIEW
Power on LED
REAR VIEW FOR RECEIVER
Channel selection switch use to fi nd optimal reception, most select same channel on both transmitter and receiver.
Audio Left out (white)
Audio Right out (red)
Channel selection switch use to fi nd optimal reception, most select same channel on both transmitter and receiver.
REAR VIEW FOR TRANSMITTER
IR extender output port
Power on/off switch
DC power input, connect to power adapter (9v)
Video
Jack(yellow)out
Power on/off switch
DC power input, connect to power adapter (9v)
Video
Jack(yellow)out
Audio Left out (white)
Audio Right out
(red)
C. Setting Up System
To enjoy wireless video and audio, just connect the transmitter to whatever audio/video source you want to enjoy from another location, and connect the receiver(X300A or to the TV, monitor or powered speakers in that other location.
Receiver
Sat-Receiver
OR
TV
DVD Player
OR
OR
2.4GHz video, audio
Camcorder
PC
UHF
OR
OR
PC
HiFi
Transmitter
The system is suggested to connect to following A/V equipment use:
Video sources:
• Cable set-top box (with A/V output)
• Satellite Receiver
• Laser Disc Player or DVD Player
• Camcorder or Miniature CCD Camera
Audio sources:
• Compact Disk Player or Changer
• Stereo Receiver
• Cassette Deck
The following pages will show you how to connect transmitter to some of these A/V equipment and then demonstrate how and where to connect and fi ne a good position for receiver.
D. Connecting the System Transmitter to VCR
1. Connect one set of audio/video(A/V) cables (or SCART cable labeled «TRANSMITTER») to the
A/V jacks of the transmitter and to the A/V output jacks (or SCART connector) on the back of your
VCR. Be sure the yellow, red and white plugs match the yellow, red and white jacks on both the
VCR and the transmitter. If the VCR has only one output for audio (mono sound only), connect the white plug to that single audio output and to transmitter’s AUDIO LEFT jack.
2. Plug one end of the power adapter into the back of the transmitter and the other end into any
230-volt wall outlet (or 120-volt). Use only the adapter provided.
Note : make sure the ON/OFF switch is in the «OFF» position before connection.
3. If your VCR has only one set of A/V output jacks and you want to use it with a nearby TV, connect 75 ohm RF coaxial cable from the modulator signal OUT port on your VCR to the VHF/UHF
IN port on your TV. (Note:In order to also view cable programs on that TV, connect your incoming cable TV source to the IN port of the VCR.)
4. Locate and orient the transmitter for best performance of transmitter.
TV ANT IN
75Ω cable
TV
Transmitter
To power outlet
RCA to scart cable
VCR
Scart cable
E. Connecting the Receiver
How To Receive Wireless Audio/Video on Your TV
There are two ways to receiver wireless audio/video signals on your remote TV (TV in another location such as in bedroom, kitchen)
• Connect the receiver directly to the remote TV
• Connect the receiver to a VCR, which is then connected to the TV.
Note : If your TV has picture-in-picture capabilities, you can view any image transmitted by system, such as your sleeping baby, in a small inset picture while enjoying other programming on the rest of the screen. Consult the owner’s manual of your TV for instructions on using these capabilities.
Connecting Receiver Directly to Remote TV
1. If your TV has A/V jacks, connect one set of A/V cables (or SCART cable labeled «RECEIVER») to the TV’s A/V jacks and to the A/V output jacks on the receiver (X300A or X301A). Be sure the yellow, red and white plugs match the yellow, red and white jacks on both the TV and the receiver.
If the TV has only a single jack for audio input, connect the white plug to that jack.
Receiver
To power outlet
TV
F. Connecting to the VCR
This setup enables you to record transmitted audio and video on your remote VCR and also enjoy the picture and sound on a remote TV at the same time.
1. Connect one set of audio/video (A/V) cables to the A/V output jacks of the receiver (X300A or
X301A) and to the A/V input jacks on your VCR. Be sure the yellow, red and white plugs match the yellow, red and white jacks on both the system receiver and the VCR. If the VCR has only a single jack for audio input, connect the white plug to it.
2. If your TV has A/V input jacks, connect another set of A/V cables to the TV’s A/V input jacks and to the A/V output jacks on your VCR.
3. If your TV does not have any A/V input jack, in this case, please connect a 75 ohm coaxial cable from the TV’s antenna in (or VHF/UHF in) to VCR’s modulator output.
4. Plug one end of the power adapter into the back of the receiver and the other end into any 230 volt (or 120 volt) wall outlet. Use only the adapter provided.
Note : make sure the ON/OFF switch is in the «OFF» position before connection.
5. Locate and orient the receiver to best video and sound quality.
Receiver
To power outlet
RAC to scart cable
VCR
TV ANT IN
75Ω coaxial cable
TV
Scart cable
G. Troubleshooting, Care and Maintenance
Please read this owner’s manual carefully and follow the steps described in it. If you still have diffi culties, consult the following table. It will guide you though the most common problems and their solutions.
Problem
No picture or sound
Interference:
Noisy picture or audio
Remote control does not work
Possibles solutions
• Check the power on/off switches on the transmitter and receiver
• Check power switches on the remote TV and video source (VCR, laser disc player, satellite receiver, ect.)
• Make sure power plugs are pushed all the way in
• Check all cable connections
• Adjust receiver and transmitter antenna orientation
• Select a different channel by pushing the channel selector switch on both transmitter and receiver so that the channels match
• If using a microwave oven, turn it off
• Remove microwave oven from path between transmitter and receiver.
• Check the path between the transmitter and the audio/video source and clear any obstructions.
H. TECHNICALS FEATURES
Transmitter :
Output Level
Operating Frequency Band Modulation
Video Input Level
Audio Input Level
Video Input Impedance
Audio Input Impedance
Power consumption
Operation Temperature
Dimensions
Weight
Receiver :
Output Level
Power Consumption
Frequency
Operation Temperature
Dimensions
Weight
90 dB µV/meter at 3 m (comply with FCC, BZT)
2.4 to 2.4835 GHZ FM (video and audio)
1V p-p @ 75 ohms
2V p-p @ 600 ohms
75 ohms
600 ohms
9 Vdc, 150 mA
0°C~50°C (Indoor use only)
17.8 X 12.6 X 6 cm
286g
1 Vp-p @75 ohms (video), 3 volt p-p (audio)
9 Vdc, 280 mA
433.92 MHz (BZT, FCC)
0°~50°C (Indoor use only)
17.8 X 12.6 X 6 cm
312g
Société NORMAND OPTEX
Zone industrielle du Pommier
Boulevard Eugène Thomas
62110 Hénin-Beaumont www.optex.fr

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 2.4Ghz frequency band, avoiding common interferences
- FHSS technology with 4ms ultra-low latency
- Transmits uncompressed real-time video and audio
- Easy plug-and-play setup, no configuration required
- Compact size and lightweight for easy placement
- 1-year warranty for peace of mind
- Supports a wide range of audio and video inputs