DPS-6.9̲Setup.fm Page 1 Monday, September 8, 2008 1:08 PM
DPS-6.9 HDMI Setup Guide
With HDMI you can...
• Easily connect video, audio, and control signals with just one HDMI cable.
• Enjoy high-definition video (1080p/1080i/720p).
• Output 480i/576i video as it is for processing by an AV receiver or TV with advanced scaling built in.
• Enjoy 5.1-channel Dolby Digital and DTS digital surround sound, and multichannel linear PCM
(DVD-Audio) and DSD (SACD).
• Use RIHD (Remote Interactive over HDMI).
Connecting Directly to a TV
Connecting to an AV Receiver
Video and audio are sent to the TV via the HDMI cable.
Video and audio are sent via the HDMI cables. You can
enjoy better sound by using an AV receiver.
HDMI
Speakers
HDMI
TV
Video
Audio
HDMI
IN
Video
Audio
HDMI indicator
HDMI
IN
HDMI
AV receiver
HDMI indicator
TV
Video
Audio
When the DPS-6.9 is outputting a signal from its
HDMI OUT, the DPS-6.9’s HDMI indicator lights
up. If the indicator does not light up, the HDMI connections are not correct, or a connected HDMI component is not turned on. The HDMI indicator flashes
while the DPS-6.9 verifies a connected HDMI component.
HDMI
IN
The connection method shown here can be used when
the AV receiver’s HDMI input supports DSD and multichannel linear PCM over HDMI. If your AV receiver
supports only CD and DVD-Video playback over HDMI,
you’ll need to use “Connection method 2” on page 21
of the DPS-6.9 Instruction Manual. Refer to the Instruction Manual for more details.
If There’s No Picture via HDMI...
DPS-6.9
Remote controller
or
By default, the HDMI Resolution is set to Auto so that video is automatically output at
a resolution that suits the connected HDMI component. However, if there’s no picture,
try pressing the [Resolution] button on the DPS-6.9 or its remote controller.
The HDMI resolution can also be set by using the onscreen setup menus, which can be
displayed by pressing the [Setup] button. See pages 46 and 50 of the DPS-6.9 Instruction Manual for details.
En
DPS-6.9̲Setup.fm Page 2 Monday, September 8, 2008 1:08 PM
If There’s No Sound via HDMI...
By default, the HDMI Audio Out setting is set to Auto so that audio is automatically output in a format that suits the connected HDMI component. However, if there’s no sound, you will need to change the HDMI Audio Out setting. See
pages 24–26 or page 51 of the DPS-6.9 Instruction Manual for details.
Using RIHD
To use RIHD, make sure CEC is enabled on your other CEC-compatible AV components (e.g., TV or AV receiver). On
the DPS-6.9, make sure the HDMI Control, Power Control, and Direct Change settings are all set to On.
About RIHD-compatible Components
The TVs listed below (in no particular order) are compatible with RIHD.
• Panasonic TVs that support VIERA LINK
• Toshiba TVs that support REGZA-LINK
Components other than those listed here may also provide linked operation if they support the CEC part of the HDMI standard, however, operation cannot be guaranteed.
Displaying Message IDs when Troubleshooting HDMI Issues
DPS-6.9
You can check the status of the HDMI connection by pressing and holding down the DPS-6.9’s [Display]
button for 10 seconds until a message ID appears on the display. Look up the message ID in the following
tables and check the HDMI connections and settings on both the DPS-6.9 and the connected component.
The page numbers in parentheses refer to the DPS-6.9 Instruction Manual.
HDMI connection and HDMI-related settings status
Displayed ID
MSG ID 001
MSG ID 005
MSG ID 015
Message
Turn the DPS-6.9 and the connected component off, then turn them on again. Make sure that the connected
component is working properly and that the DPS-6.9’s HDMI settings are configured suitably for that component.
\No picture from the HDMI connection
Displayed ID
Message
MSG ID 002
The HDMI Output Setting is set to Off. Change it to On (page 46).
MSG ID 003
MSG ID 004
The HDMI cable may not be connected properly. Check the connection. Also, make sure the HDMI input on the
TV or AV receiver is correctly configured to received HDMI.
MSG ID 005
MSG ID 006
MSG ID 007
Make sure the HDMI input on the TV or AV receiver is correctly configured to received HDMI.
The connected component may not support HDCP. Make sure the connected component supports HDCP.
Turn the DPS-6.9 and the connected component off, then turn them on again.
The DPS-6.9 may be connected to the other component’s DVI jack. Some TVs may not properly receive the
video output by the DPS-6.9. Also, with a DVI connection, there will be no sound.
MSG ID 008
The DPS-6.9’s HD Resolution setting is set to 480i/576i, 720p, 1080i, or 1080p. If your TV doesn’t support
these resolutions, select another resolution (page 46).
MSG ID 009
The connected component may not be receiving the HDMI signal properly.
Check the settings on the connected component.
No sound from the HDMI connection
Displayed ID
Message
MSG ID 009
The connected component may not be receiving the HDMI signal properly.
Check the settings on the connected component.
MSG ID 010
MSG ID 021
The DPS-6.9’s HDMI Audio Out setting is set to Off. Change the setting to Auto, 6ch DSD, 6ch PCM, or 2ch
PCM (page 51).
MSG ID 012
MSG ID 013
The connected component may not support Dolby Digital. Set the DPS-6.9’s HDMI Audio Out setting to Auto or
2ch PCM (page 51).
MSG ID 016
MSG ID 017
The connected component may not support DTS. Set the DPS-6.9’s HDMI Audio Out setting to Auto or 2ch
PCM (page 51).
MSG ID 020
When playing an SACD or DVD-Audio disc, the HDMI Audio Out setting is set to 6ch DSD, 6ch PCM, or Off, but
your AV receiver or TV does not support these audio formats. Change the setting to Auto or 2ch PCM.
For more information, refer to the manuals for the DPS-6.9 and the other component.
I0809-1
SN 29344810
(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 8 1 0 *
">
