Integra | DRX-5.3 | Quick Start Guide | Integra DRX-5.3 Receiver Quick Start Guide

Integra DRX-5.3 Receiver Quick Start Guide
Initial Setup Guide
*1 *2 *3
Install & Connections
1
2
DRX-5.3
AV Receiver
SN 29403676
F1902-0
* 2 9 4 0 3 6 7 6 *
*1
a
b
c
3
a: 22° to 30°, b: 90° to 110°, c: 135° to 150°
7.1 ch System
1,2
3
4,5
6
7,8
Front Speakers
Center Speaker
Surround Speakers
Powered Subwoofer
Surround Back Speakers
Refer to the instruction
manual available on our
website to install and
connect speaker systems
other than 7.1 ch.
a
b
a Speaker cable, b Subwoofer cable
*2
4-16Ω
http://integraworldwide.com/manual/drx53/top.pdf
a
*3
ᴧ
ᴧº 1/2˝
(12 mm)
Refer to the instruction manual available
on our website to install and connect
speaker systems other than 7.1 ch.
http://integraworldwide.com/manual/drx53/top.pdf
SN29403676_DRX-5.3_QSG_En.indd
1
2019/02/14
17:06:17
4
5
c HDMI cable
d Digital optical cable
d
*6
*1
Used during Initial Setup.
*2
Connect speakers with 4 Ω to 16 Ω impedance. If any of the connected speakers have 4 Ω or more to
less than 6 Ω impedance, in "Initial Setup", "Speaker Setup", set "Speaker Impedance" to "4ohms".
DIGITAL
OPTICAL OUT
*3
ARC TV
c
Non-ARC TV
c+d
IN(ARC)
c
Make sure the wires at the ends of the speaker cables are twisted tightly and do not stick out of the
speaker terminals when connecting. The unit can be damaged if the exposed wires of the speakers
touch the rear panel or the + and - wires touch each other.
*4
If it is an ARC TV, connect to the ARC compatible input jack on the TV. Settings are required to use the
ARC function. Select "Yes" for "ARC Setup" in "Initial Setup".
*5
ARC *4
To output the audio of an AV component to ZONE 3, as well as connecting using the HDMI cable, it is also
necessary connect using an analog audio cable. For details, refer to the instruction manual.
*6
If you connect this unit to the network using wired LAN, connect an LAN cable to the ETHERNET port.
*7
Switch the input on the TV to that assigned to the unit. Follow the guidance displayed on the screen to
complete Initial Setup. Note that there are a maximum of 9 listening points available for measuring with
"AccuEQ Room Calibration" when the listening area is large. Also, if you selected "No, Skip" for "ARC
Setup", to enable HDMI CEC and HDMI Standby Through function, after completing Initial Setup, you will
need to press on the remote controller and make the settings in "6. Hardware" - "1. HDMI".
Tips
(North American
models)
When the unit is operating erratically
(Australian models)
If operation becomes unstable, try restarting the unit. Set the unit to standby,
then press and hold  On/Standby on the main unit for 5 seconds or more.
5"
If restarting doesn’t fix the problem, try unplugging the power cord and HDMI
cables then replugging them in again, initializing settings (with the unit ON, while
pressing CBL/SAT on the main unit, press  On/Standby.), and trying Firmware
Update.
6
*5
BD/DVD
GAME
Cable/Satellite set-top box
Streaming
media player
Initial Setup with Auto Start-up Wizard
TV’s REMOTE
7.1.2ch
*7
INPUT
Inputs
Initial Setup
1st Step : Speaker Setup
2nd Step : AccuEQ Room Calibration
3rd Step : Multi Zone Sound Check
4th Step : ARC Setup
5th Step : Network Connection
TV
HDMI 1
HDMI 2
HDMI 3
7.1ch
Speaker Setup
Speaker Channels
Subwoofer
Height 1 Speaker
7.1 ch < >
Yes
---
Height 2 Speaker
---
Zone Speaker
No
Zone 2 Preout
Zone 2
TV
Bi-Amp
No
Speaker Impedance 6ohms or above
Select how many speakers you have.
Next
To redo the initial setup
"8. Miscellaneous"
SN29403676_DRX-5.3_QSG_En.indd
2
"4.Initial Setup"
2019/02/14
17:06:21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising