Integra | DRX-3.2 | Quick Start Guide | Integra DRX-3.2 Receiver Quick Start Guide

Integra DRX-3.2 Receiver Quick Start Guide
Initial Setup Guide
1 2 3
Install & Connections
1
2
DRX-3.2
AV RECEIVER
SN 29403393
H1803-0
* 2 9 4 0 3 3 9 3 *
1
*1
*2
*3
3
* 1: 22° to 30°, * 2: 90° to 110°, * 3: 135° to 150°
7.1 ch System
1,2
3
4,5
6
7,8
Front Speakers
Center Speaker
Surround Speakers
Powered Subwoofer
Surround Back Speakers
Refer to the instruction manual
available on our website to install and
connect speaker systems other than
7.1 ch.
b
a
a Speaker cable, b Subwoofer cable
2
4-16Ω
http://integraworldwide.com/manual/drx32/top.pdf
3
1/2˝
(12 mm)
Refer to the instruction manual available on our website to install and
connect speaker systems other than 7.1 ch.
http://integraworldwide.com/manual/drx32/top.pdf
4
1
5
c HDMI cable
d Digital optical cable
Used during Initial Setup.
2
Connect speakers with 4 Ω to 16 Ω impedance. If any of the connected speakers have an impedance of 4 Ω or more to less than 6 Ω, after completing "Initial
on the remote controller, select "2. Speaker" - "1. Configuration" and set "Speaker
Setup", you need to make some settings in the Setup menu. Press
Impedance" to "4ohms ".
DIGITAL
OPTICAL OUT
d
4
3
ARC TV
c
Non-ARC TV
c+d
c
5
Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear
panel or the + and – wires touch each other, the protection circuit will be activated.
4
Choose an HDMI IN jack on the TV that supports ARC when connecting. Settings are required to use the ARC function. Select "Yes" for "ARC Setup" in
"Initial Setup".
5
If you connect this unit to the network using wired LAN, connect an LAN cable to the ETHERNET port.
6
ARC
Switch the input on the TV to that assigned to the unit. Complete the Initial Setup according to the guidance displayed on the screen.
Enable HDMI CEC & HDMI Standby Through function: If you selected "No, Skip" in "ARC Setup" of "Initial Setup", after completing "Initial Setup", it is
necessary to press the
button on the remote controller and execute "6. Hardware" - "1.HDMI" setting.
Tips Troubleshoot your remote control
The remote control may have switched to the mode for controlling ZONE 2. While holding down Mode, press Main until
the remote indicator flashes once to switch it to the mode to control the main room.
(North American
models)
(Australian models)
6
BD/DVD
Cable/Satellite set-top box
Streaming
media player
GAME
Initial Setup with Auto Start-up Wizard
TV’s REMOTE
6
INPUT
Inputs
Initial Setup
Speaker Setup
Speaker Channels 7.1 ch < >
TV
HDMI 1
HDMI 2
HDMI 3
Subwoofer
Height 1 Speaker
Yes
---
TV
Height 2 Speaker
---
Zone Speaker
No
Bi-Amp
No
Select how many speakers you have.
Next
To redo the initial setup
“8. Miscellaneous”
“4.Initial Setup”
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising