Integra | DSX-3 | Owner Manual | Integra DSX-3 Receiver Owner Manual

Integra DSX-3 Receiver Owner Manual
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
AV Receiver
DSX-3
Instruction
Manual
Before Start
What's in the box .................................................................... 2
Part Names
Front Panel ............................................................................. 3
Rear Panel .............................................................................. 4
Remote Controller .................................................................. 5
Display .................................................................................... 6
Install
1. Speaker Layout .................................................................. 7
2. Connect the Speakers ...................................................... 12
3. Connect the TV ................................................................. 14
4. Connect the HDMI AV Components ................................. 15
5. Connect the Audio Components ....................................... 16
6. Connect Other Cables ...................................................... 17
Initial Setup
Initial Setup with Auto Start-up Wizard ................................. 18
Playback
AV Component Playback ...................................................... 21
Internet Radio ....................................................................... 22
Spotify ................................................................................... 24
Music Server ......................................................................... 25
USB Storage Device ............................................................. 27
AirPlay® ................................................................................ 29
BLUETOOTH® Playback ...................................................... 30
Listening to the FM Radio ..................................................... 31
Listening Modes ................................................................... 32
Quick Menu .......................................................................... 50
Other Functions .................................................................... 52
Supplementary information
Supplementary information for player functions .................... 53
Advanced Setup
Setup Menu ........................................................................... 54
Control Function Settings ...................................................... 68
Firmware Update .................................................................. 69
Others
Troubleshooting .................................................................... 72
General Specifications .......................................................... 77
About HDMI .......................................................................... 79
License and Trademark Information ..................................... 80
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
What's in the box
Before Start
Main unit (1)
Remote controller (RC-936R) (1), batteries (AAA/R03) (2)
Speaker setup microphone (1)
Indoor FM antenna (1)
2
Power cord (1)
0 Connect speakers with 4 Ω to 8 Ω impedance.
0 The power cord must be connected only after all other cable connections are completed.
0 We will not accept responsibility for damage arising from the connection of equipment
manufactured by other companies.
0 Functionality may be introduced by firmware updates and service providers may cease
services, meaning that some network services and content may become unavailable in
the future. Furthermore, available services may vary depending on your area of
residence.
0 Specifications and appearance are subject to change without prior notice.
0 We plan to provide support for the Dolby Atmos and DTS:X audio format through a
firmware update for this unit. Refer to our website for more information.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Front Panel
Part Names


  





1. Í On/Standby button: Turns the unit on or into standby mode.
2. Hybrid Standby indicator: Lights if the unit enters standby mode when the features are
enabled that continue to work when this unit is in standby, such as HDMI Standby
Through and Network Standby.
3. Display (P6)
4. Remote control sensor
5. Volume dial: Allows you to adjust the volume.
6. USB port: A USB storage device is connected so that music files stored in it can be
played. You can also supply power (maximum 5 V/1 A) to USB devices with a USB cable.
7. Phones jack: Stereo headphones with a mini plug (φ3.5 mm) are connected.
8. Input button: Switches the input to be played. (BD/DVD / CBL/SAT / GAME / STRM BOX /
CD / TV / PHONO / FM / NET / USB / BLUETOOTH)
9. Listening Mode button: Allows you to select the listening mode. (P32)
10.Tuning4 3buttons: Select the frequency of FM radio stations.
3
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Rear Panel

 


 


90°

180°



1. TUNER FM 75Ω jack: Connect the supplied antenna.
2. Wireless antenna: Raise for Wi-Fi connection or when using a BLUETOOTH enabled
device. The diagram shows the movable range for the wireless antenna. Do not try to
force it beyond this range otherwise you may break it.
3. AUDIO IN jacks: Input TV or AV component audio signals with an analog audio cable.
4. GND terminal: The ground wire of the turntable is connected.
5. DIGITAL IN OPTICAL/COAXIAL jacks: Input TV or AV component digital audio signals
with a digital optical cable or digital coaxial cable.
6. IR IN jack: Allows you to connect a multiroom remote control kit.
7. SETUP MIC jack: The supplied speaker setup microphone is connected.
8. AC INLET: The supplied power cord is connected.
9. ETHERNET port: Connect to the network with an Ethernet cable.
10.HDMI OUT jack: Connect a HDMI cable to transfer video signals and audio signals to a
TV.
11. HDMI IN jacks: Input video signals and audio signals with a HDMI cable connected to an
AV component.
12.SPEAKERS terminals: Connect speakers or passive subwoofers with speaker cables.
13.SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a subwoofer cable.
4


> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Remote Controller










1. Í button: Turns the unit on or into standby mode.
2. Input selector buttons: Switches the input to be played.
3. Q (Quick Menu) button: You can perform common settings on the TV screen. (P50)
4. Cursors, Enter button: Select the item with the cursors and press Enter to confirm.
5.
button: Displays the Setup menu. (P54)
6. Volume buttons: Allows you to adjust the volume. This button also cancels the muting.
7.
button: Temporarily mutes audio. Press again to cancel muting.
8. Listening mode buttons: Allows you to select the listening mode. (P32)
9. Play buttons: You can start play of the Music Server or USB.
10.
button: You can start repeat or random play of the Music Server or USB.
Clear button: Deletes all characters you have entered when entering text on the TV
screen.
11. Dimmer button: You can adjust the brightness of the display in three steps. It cannot be
turned off completely.
12.
button: Switches the information on the display.
13.
button: Returns the display to the previous state during setting.
14.Mode button: Switches tuning to an FM station between automatic tuning and manual
tuning.
15.Memory button: Used to register FM radio stations.
30°
30°



Approx.5 m
(16 ft.)


5
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Display

 



Neo:6

1. Lights in the following conditions.
HDMI: HDMI signals are input and selected.
ARC: Audio signals from the ARC compatible TV are input and selected.
USB: When "USB" is selected with the input selector and the unit is connected by USB
and the USB device is selected. Flashes if the USB is not properly connected.
NET: When "NET" is selected with the input selector and the unit is connected to the
network. It will flash if the connection to the network is not correct.
DIGITAL: Digital signals are input and the digital input selector is selected.
2. Lights when operating the "NET" or "USB" input selector indicating remote controller
cursor operations are possible in screens showing list of tracks, for example.
3. Lights when headphones are connected.
4. Lights when operating the "NET" or "USB" input selector when tracks are played or
paused.
5. Lights according to the type of input digital audio signals and the listening mode.
6. Lights in the following conditions.
AUTO: When tuning mode is auto.
TUNED: Receiving FM radio.
FM STEREO: Receiving FM stereo.
SLEEP: Sleep timer has been set.
ASb: When Auto Standby function is enabled. (P65)
6
7. Flashes when muting is on.
8. Displays various information of the input signals. Characters that cannot be displayed on
this unit are replaced with asterisks ( * ).
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
1. Speaker Layout
Install
5.1 Channel System
Front speakers output front stereo sound and the center
speaker outputs sounds emanating from the center of the
screen, such as dialog and vocals. Surround speakers
create the sound field at the rear. The powered subwoofer
reproduces bass sounds and enriches the sound field. The
optimal positioning for front speakers is at ear height, and for
surround speakers it is just above ear height. The center
speaker should be set up at an angle to face the listening
position. Placing the powered subwoofer between the center
speaker and a front speaker gives you a natural sound even
when playing music.
*1
*2
1,2
3
4,5
6
Front Speakers
Center Speaker
Surround Speakers
Powered Subwoofer
* 1: 22e to 30e, * 2: 120e
7
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
3.1.2 Channel System-1
(Front High Speakers)
3´ (0.9 m)
or more
*1
This is a 3.1-channel system consisting of front speakers, a
center speaker, and a powered subwoofer, with the addition
of front high speakers, a type of height speaker. Front high
speakers should be situated at least 3y/0.9 m higher than
the front speakers. They should also be put directly above
the front speakers, angled to face the listening position.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. After this
firmware update, by installing height speakers, you can
select the Dolby Atmos listening mode, which realizes the
most up-to-date 3D sound including overhead sounds,
when the input format is Dolby Atmos. Visit our website
for details about firmware updates.
1,2
3
4,5
6
* 1: 22e to 30e
8
Front Speakers
Center Speaker
Front High Speakers
Powered Subwoofer
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
3.1.2 Channel System-2
(Ceiling Speakers)
*1
This is a 3.1-channel system consisting of front speakers, a
center speaker, and a powered subwoofer, with the addition
of top middle speakers, a type of height speaker. Fit top
middle speakers on the ceiling directly above the listening
position. The distance between each pair should match the
distance between the two front speakers.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. After this
firmware update, by installing height speakers, you can
select the Dolby Atmos listening mode, which realizes the
most up-to-date 3D sound including overhead sounds,
when the input format is Dolby Atmos. Visit our website
for details about firmware updates.
0 Dolby Laboratories recommends placing this type of
height speakers to obtain the best Dolby Atmos effect.
1,2
3
4,5
6
Front Speakers
Center Speaker
Top Middle Speakers
Powered Subwoofer
* 1: 65e to 100e
9
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
3.1.2 Channel System-3
(Dolby Enabled Speakers (Dolby Speakers))
*1
This is a 3.1-channel system consisting of front speakers, a
center speaker, and a powered subwoofer, with the addition
of Dolby enabled speakers (front), a type of height speaker.
Dolby enabled speakers are special speakers designed to
face the ceiling so that sound is heard after bouncing off the
ceiling so that sound appears to be coming from overhead.
Place Dolby enabled speakers (front) above the front
speakers.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. After this
firmware update, by installing height speakers, you can
select the Dolby Atmos listening mode, which realizes the
most up-to-date 3D sound including overhead sounds,
when the input format is Dolby Atmos. Visit our website
for details about firmware updates.
1,2
3
4,5
6
* 1: 22e to 30e
10
Front Speakers
Center Speaker
Dolby Enabled Speakers (Front)
Powered Subwoofer
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Speaker combinations
Speaker Channels
FRONT
CENTER
SURROUND
HEIGHT
2.1 ch
3.1 ch
4.1 ch
5.1 ch
2.1.2 ch
3.1.2 ch
11
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
2. Connect the Speakers
1
a
1/2˝
(12 mm)
2
a
b
a
3
b
a Speaker cable, b Subwoofer cable
12
Connect the speakers
Refer to the illustration to connect the speaker system.
Twist the wires of the speaker cable tightly before inserting
into the SPEAKERS terminals. Make correct connection
between the unit’s jacks and speaker’s jacks (i to i and j
to j) for each channel. If connection is wrong, a bass
sound may become poor due to reverse phase.
Either a powered subwoofer or passive subwoofer may be
connected. To connect a powered subwoofer, use a
subwoofer cable and connect to the SUBWOOFER PRE
OUT jack. To connect a passive subwoofer, connect to the
SPEAKERS terminals with speaker cables as shown below.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Make sure the exposed wires of the speakers do not stick
out of the speaker terminals when connecting. If the
exposed wires of the speakers touch the rear panel or the +
and – wires touch each other, the protection circuit will be
activated. (P72)
Setup
0 Settings for the speaker configuration you have
connected need to be made in "1. AccuEQ Room
Calibration" (P19) in Initial Setup.
13
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
3. Connect the TV
To ARC TV
1
For a TV that supports the ARC (Audio Return Channel)
(P79) feature, use an HDMI cable and connect according
to illustration "a". Choose an HDMI IN jack on the TV that
supports ARC when connecting.
To Non-ARC TV
DIGITAL
OPTICAL OUT
For a TV that does not support the ARC (Audio Return
Channel) feature, connect both the HDMI cable in illustration
"a" and the digital optical cable in "b".
b
a
Setup
0 Settings are required to use the ARC function. Select
"Yes" in "4. Audio Return Channel" (P20) in the Initial
Setup.
0 Please refer to the TV’s operation manual for directions
on connections and setup for the TV.
a HDMI cable, b Digital optical cable
14
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
4. Connect the HDMI AV Components
1
a
a
BD/DVD
Streaming media
player
Cable/Satellite
set-top box
HDMI OUT
e.g. BD
This is an example of connection with an AV component
that has an HDMI jack. With connection to an AV
component that conforms with the CEC (Consumer
Electronics Control) standard, you can use features such as
the HDMI CEC feature that links with the input selector, and
the HDMI Standby Through feature which allows you to
play video and audio from AV components on the TV even
when this unit is in standby mode. (P79)
0 To play 4K or 1080p video, use the high speed HDMI
cable.
GAME
Setup
0 Settings are required to use the HDMI CEC and HDMI
Standby Through features. (P62) Make settings after
all connections are complete.
0 To enjoy digital surround sound including Dolby Digital,
audio output should be set to "Bitstream output" on the
connected Blu-ray Disc player or other device.
a HDMI cable
15
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
5. Connect the Audio Components
Connecting a CD player
Use a digital coaxial cable to connect a CD player to the
DIGITAL IN COAXIAL jack.
Connecting a turntable
You can also connect a turntable that has an MM-type
cartridge to the PHONO jack.
0 If the turntable has a built-in audio equalizer, connect it to
an AUDIO IN jack other than the PHONO jack. Further, if
the turntable uses an MC type cartridge, install an audio
equalizer compatible with the MC type cartridge between
the unit and the turntable, then connect to any AUDIO IN
jack other than the PHONO jack.
b
a
If the turntable has a ground wire, connect it to the GND
terminal of this unit.
Turntable
a Digital coaxial cable, b Analog audio cable
16
CD
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
6. Connect Other Cables
1
Antenna Hookup
2
Connect the supplied FM indoor antenna to the TUNER FM
75Ω terminal. Move the FM indoor antenna around while
playing the radio to find the position with the best reception.
Network Hookup
a
b
3
Connect this unit to the network using wired LAN or Wi-Fi
(wireless LAN). You can enjoy network features such as
internet radio by connecting the unit to the network. If you
connect by wired LAN, connect with an Ethernet cable to the
ETHERNET port as shown in the illustration. To connect by
Wi-Fi, then after selecting "Wireless" in "3. Network
Connection" (P20) in Initial Setup, select the desired
setting method and follow the onscreen instructions to
configure the connection.
Power Cord Hookup
c
c
This unit includes a removable power cord. Connect the
power cord to the power outlet after completing all other
connections. Connect the power cord to AC INLET of the
unit and then connect to the outlet. Always disconnect the
outlet side first when disconnecting the power cord.
a FM indoor antenna, b Ethernet cable, c Power cord
17
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Initial Setup with Auto Start-up Wizard
Initial Setup
1
2
Initial Setup starts automatically
1. Switch the input on the TV to that assigned to the unit.
2. Put batteries into the remote controller of this unit.
3. Press Í on the remote controller. When power is turn on
for the first time, an Initial Setup screen is automatically
displayed on the TV to allow you to make settings
required for start up.
Initial Setup
Language Select
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
Русский язык
中文
TV's remote controller
3
4
Exit
4. Follow the on-screen instructions to select the item with
the cursors of the remote controller and press Enter to
confirm your selection.
0 To return to the previous screen, press
.
To redo Initial Setup: If you terminate the procedure on the
way or want to change a setting made during Initial Setup,
press
on the remote controller, select "6. Miscellaneous"
- "Initial Setup" in the Setup menu and press Enter. To select
the language displayed again, change "OSD Language".
(P54)
18
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
1. AccuEQ Room Calibration
Place the supplied speaker setup microphone in the
listening position, measure the test tones emitted by the
speakers, then the unit automatically sets the optimum
volume level for each speaker, the crossover frequencies,
and the distance from the listening position. This also
automatically adjusts the equalizers for the speakers and
enables correction of distortion caused by the acoustic
environment of the room.
0 Calibration takes between 3 to 12 minutes to be
completed. The speakers emit the test tone at high
volume during measurement, so be careful of your
surroundings. Keep the room as quiet as possible during
measurement.
0 If the power of this unit suddenly turns off, the wires in the
speaker cables may have touch the rear panel or other
wires and tripped the protection circuit. Twist the wires
again properly and make sure they do not stick out of the
speaker terminals when connecting.
1. Place the supplied speaker setup microphone in the
listening position, and connect to the SETUP MIC jack on
the main unit.
SETUP MIC
0 To cancel AccuEQ Room Calibration partway through,
disconnect the speaker setup microphone.
2. Select the connected speaker configuration.
AccuEQ Room Calibration
AccuEQ Room Calibration
Review Crossover
Subwoofer
: Yes
Front
: 100Hz
Center
: 100Hz
Surround
: 100Hz
Speaker Channels 5.1 ch < >
Subwoofer
Yes
Height Speaker
---
Save
Cancel
Select how many speakers you have.
Next
The image on the screen changes as you choose the
number of channels in "Speaker Channels", so refer to it
when performing the settings. Also use this screen to
select whether you have connected a subwoofer.
0 If you have connected a subwoofer, check the power
and volume of the subwoofer. The low frequencies
played by the subwoofer may not be discernible, so
set its volume to at least halfway.
3. Test tones are emitted by the speakers, and firstly the
unit detects the speakers connected and the noise in the
environment.
4. After the results of the above measurements are
displayed, select "Next", press Enter on the remote
controller, and the test tones are emitted again, and the
unit automatically makes settings such as the optimum
volume level and the crossover frequency.
5. When the measurement is completed, the measurement
result is displayed.
Press the cursors / on the remote controller to check
the settings. Press Enter when "Save" is selected to save
the settings.
6. Select whether to enable or disable the equalizer function
that corrects for distortion caused by the acoustic
environment of the room.
AccuEQ Room Calibration
To enable equalizer for each speakers, select "On".
Please select "All Channels", if you have same speakers for all
channels. Please select "Except Front Left / Right", if front
speakers are larger than other speakers.
On (All Channels)
On (Except Front Left / Right)
Off
Next
If this is to be enabled, then normally you should select
"On (All Channels)", and to disable just the front
speakers you should select "On (Except Front Left /
Right)".
7. Disconnect the speaker setup microphone.You cannot
use any other menu options while it is connected.
2. Source Connection
Check that each input source is connected correctly. Follow
the guidance, select the input you want to confirm, start play
of the selected player, and confirm that the images appear
on the TV and that sound is played.
When putting the speaker setup microphone on a tripod,
refer to the illustration when putting it in place.
19
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
3. Network Connection
4. Audio Return Channel
Set up Wi-Fi connection with an access point such as a
wireless LAN router. There are the following two methods of
connecting by Wi-Fi:
"Scan Networks": Search for an access point from this
unit. Find out the SSID of the access point beforehand.
"Use iOS Device (iOS7 or later)": Share the iOS device's
Wi-Fi settings with this unit.
If you have connected a TV that supports ARC, select
"Yes". This unit's ARC setting turns on and you can listen to
the TV's audio through this unit.
0 If you select "Yes", the HDMI CEC function is enabled
and power consumption increases during standby.
If you select "Scan Networks", there are a further two
choices of connection method. Check the following.
0 "Enter Password": Enter the password (or key) of the
access point to connect.
0 "Push Button": If the access point has an automatic
connection button, you can connect without entering a
password.
0 If the SSID of the access point is not displayed, then in
the screen listing the SSIDs, select "Other..." with the 
button on the remote controller and press Enter, then
follow the on-screen instructions.
Wi-Fi Setup
Ðáóó÷ïòä
a
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
1
b
2
3
c
d
4
e
5
6
f
g
7
8
9
0
-
^
\
,
.
/
;
:
@
[
]
A/a
h
OK
When finished, select the "OK" key.
All Erase
Hide/Show
A/a
Keyboard input: To switch between upper and lower case,
select "A/a" on the screen and press Enter. To select
whether to mask the password with "*" or display it in plain
text, press Memory on the remote controller. Pressing Clear
will delete all the input characters.
Privacy policy: A confirmation screen asking you to agree
to the privacy policy is displayed during network setting.
Select "Yes" and press Enter to indicate agreement.
20
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
AV Component Playback
Playback
Basic operations
Play an AV component or TV connected to this unit with an
HDMI cable or other cable.
1. Switch the input on the TV to that assigned to the unit.
2. Press the input selector (a) on the remote controller with
the same name as the jack to which you connected the
player to switch the input.
For example, press BD/DVD to play the player connected
to the BD/DVD jack. Press TV to listen the TV's sound.
0 Note that when the CEC link function works, the input
switches automatically when you have connected a
CEC compliant TV and player to this unit using HDMI
connection.
3. Start play on the player.
4. Use VOL+/– (b) to adjust the volume.
a
b
21
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Internet Radio
1
a
b
Basic operations
Pandora®
When this unit is connected to a network, you can listen to
TuneIn or other preregistered Internet radio services.
Depending on the internet radio service, the user may need
to register from their computer first.
1. Switch the input on the TV to that assigned to the unit.
2. Press NET on the remote controller.
Pandora is a free, personalized Internet radio service that
plays the music you know and helps you discover music
you’ll love. After selecting "Pandora", do the following.
1. Use / (a) on the remote controller to select "I have a
Pandora Account" or "I’m new to Pandora" and then
press Enter (b).
If you are new to Pandora, select "I’m new to Pandora".
You will see an activation code on your TV screen.
Please write down this code. Go to an Internet connected
computer and point your browser to www.pandora.com/
integra. Enter your activation code and then follow the
instructions to create your Pandora account and your
personalized Pandora stations. You can create your
stations by entering your favorite tracks and artists when
prompted. After you have created your account and
stations you can return to your receiver and press Enter
(b) to begin listening to your personalized Pandora.
If you have an existing Pandora account, you can add
your Pandora account to your receiver by selecting "I
have a Pandora Account" and logging in with your email
and password.
2. To play a station, use / (a) on the remote controller to
select the station from your station list, and then press
Enter (b). Playback starts and the playback screen
appears.
3. Follow the on-screen instructions, using the cursors to
select radio stations and programs, then press Enter (b)
to play. Play starts when 100% is displayed for buffering.
0 To return to the previous screen, press
(c).
0 If you cannot select a network service, it will become
selectable when the network function is started.
Regarding the TuneIn Radio
c
To display the TuneIn Radio menu during play, press Enter
(b) on the remote controller.
Add to My Presets: Registers radio stations being
broadcast and programs in "My Presets". Once registered,
"My Presets" is displayed in the level under TuneIn Radio.
To play, select the program you like from "My Presets".
Remove from My Presets: Removes a radio station or
program from "My Presets" in TuneIn Radio.
Create new station: Enter the name of a track, artist, or
genre and Pandora will create a unique radio station for you
based on the musical qualities of that track, artist, or genre.
Regarding the Pandora Menu: Icons are displayed on the
screen while playing a station. You can do the following by
selecting the icon with / (a) on the remote controller and
pressing Enter (b).
(I like this track) :
Give a track "thumbs-up" and Pandora will play more music
22
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
like it.
(I don't like this track) :
Give a track "thumbs-down" and Pandora will ban that track
from the current station.
:
Automatically find stations matching your preferences
based on genre, specific artists, and songs, and delete
those stations you don't need.
23
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Spotify
Basic operations
1
Spotify Connect play is possible by connecting this unit to
the same network as a smart phone or tablet. To enable
Spotify Connect, install the Spotify application on your
smartphone or tablet and create a Spotify premium account.
1. Connect the smartphone to the network that this unit is
connected to.
2. Click the Connect icon in the track play screen of the
Spotify app.
3. Select this unit.
4. This unit turns on automatically and the input selector
changes to NET and streaming of Spotify starts.
0 If "5. Hardware" - "Power Management" - "Network
Standby" is set to "Off" in the Setup menu, manually turn
the unit on and then press NET on the remote controller.
0 Refer to the following for Spotify settings:
www.spotify.com/connect/
0 The Spotify software is subject to third party licenses
found here:
www.spotify.com/connect/third-party-licenses
Wi-Fi
2
a
b
3
c
d
e
4
Integra DSX-3 XXXX
24
The following remote controller operations are also
possible.
(a) Pressed during play, this button changes the displayed
track information.
(b) This button plays the previous track.
(c) This button lets you start repeat or random playback.
Pressing this button repeatedly cycles through the
repeat modes.
(d) Pressed during play this button pauses playback.
Pressed while paused, and it restarts play.
(e) This button plays the next track.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Music Server
It is possible to stream music files stored on PCs or NAS
devices connected to the same network as this unit. The
network servers this unit is compatible with are those PCs
with players installed that have the server functionality of
Windows Media® Player 11 or 12, or NAS that are
compatible with home network functionality. You may need
to make some settings in advance to use Windows Media®
Player 11 or 12. Note that only music files registered in the
library of Windows Media® Player can be played.
1
Configuring Windows Media® Player
a
■ Windows Media® Player 11
1. Turn on your PC and start Windows Media® Player 11.
2. In the "Library" menu, select "Media Sharing" to display a
dialog box.
3. Select the "Share my media" check box, and then click
"OK" to display the compatible devices.
4. Select this unit, click "Allow" and put a check mark next to
the icon for this unit.
5. Click "OK" to close the dialog.
0 Depending of the version of Windows Media® Player,
there may be differences in the names of items you can
select.
b
c
d
■ Windows Media® Player 12
e
f
g
h
1. Turn on your PC and start Windows Media® Player 12.
2. In the "Stream" menu, select "Turn on media streaming"
to display a dialog box.
0 If media streaming is already turned on, select "More
streaming options..." in the "Stream" menu to list players
in the network, and then go to step 4.
3. Click "Turn on media streaming" to list players in the
network.
4. Select this unit in "Media streaming options" and check
that it is set to "Allow".
5. Click "OK" to close the dialog.
0 Depending of the version of Windows Media® Player,
there may be differences in the names of items you can
select.
Playing
1. Start the server (Windows Media® Player 11, Windows
Media® Player 12, or NAS device) containing the music
files to play.
2. Make sure that the PCs and/or NASs are properly
connected to the same network as this unit.
3. Switch the input on the TV to that assigned to the unit.
4. Press NET on the remote controller.
5. With the cursors on the remote controller, select "Music
Server", and then press Enter (b).
6. Select the target server with the cursors on the remote
controller and press Enter (b) to display the items list
screen.
7. With the cursors on the remote controller, select the
music file to play, and then press Enter (b) to start
playback. To return to the previous screen, press
(d).
0 If "No Item." is displayed, check whether the network is
properly connected.
0 Depending on the server and share settings, the unit may
not recognize it, or may not be able to play its music files.
Furthermore, the unit cannot access pictures and videos
stored on servers.
0 For music files on a server, there can be up to 20,000
tracks per folder, and folders may be nested up to 16
levels deep.
25
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
The following remote controller operations are also
possible.
(a) When the folder or file lists are not shown on one screen,
you can change the screen.
(c) Pressed during play, this button changes the displayed
track information. Pressed while a folder or file list is
displayed, this button returns you to the play screen.
(e) This button plays the previous track.
(f) This button lets you start repeat or random playback.
Pressing this button repeatedly cycles through the
repeat modes.
(g) Pressed during play this button pauses playback.
Pressed while paused, and it restarts play.
(h) This button plays the next track.
Controlling Remote Playback from a PC
You can use this unit to play music files stored on your PC
by operating the PC inside your home network. The unit
supports remote playback with Windows Media® Player 12.
1. Turn on your PC and start Windows Media® Player 12.
2. Open the "Stream" menu and check that "Allow remote
control of my Player..." is checked. Click "Turn on media
streaming" to list players in the network.
3. Switch the input on the TV to that assigned to the unit.
4. Select and right-click the music file to play with Windows
Media® Player 12. To remotely play a music file on
another server, open the target server from "Other
Libraries" and select the music file to play.
5. Select this unit in "Play to" to open the "Play to" window
of Windows Media® Player 12 and start playback on the
unit. If your PC is running on Windows® 8.1, click "Play
to", and then select this unit.
If your PC is running on Windows® 10, click "Cast to
Device", and select this unit. Operations during remote
playback are possible from the "Play to" window on the
PC. The playback screen is displayed on the TV
connected to the HDMI output of the unit.
26
6. Adjust the volume using the volume bar on the "Play to"
window.
0 Sometimes, the volume displayed on the remote
playback window may differ from that appeared on the
display of the unit. Also, when the volume is adjusted
from this unit, this is not reflected in the "Play to" window.
0 Remote playback is not possible when using a network
service or playing music files on a USB storage device.
0 Depending of the version of Windows®, there may be
differences in the names of items you can select.
Supported Audio Formats
This unit supports the following music file formats. Remote
play of FLAC, DSD, and Dolby TrueHD is not supported.
MP3 (.mp3/.MP3):
0 Supported formats: MPEG-1/MPEG-2 Audio Layer-3
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR.
WMA (.wma/.WMA):
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Supported bitrates: Between 5 kbps and 320 kbps and
VBR.
0 WMA Pro/Voice/WMA Lossless formats are not
supported.
WAV (.wav/.WAV):
WAV files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AIFF (.aiff/.aif/.aifc/.afc/.AIFF/.AIF/.AIFC/.AFC):
AIFF files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/.3GP/
.3G2):
0 Supported formats: MPEG-2/MPEG-4 Audio
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR.
FLAC (.flac/.FLAC):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
LPCM (Linear PCM):
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Quantization bit: 16 bit
Apple Lossless (.m4a/.mp4/.M4A/.MP4):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 16 bit, 24 bit
DSD (.dsf/.dff/.DSF/.DFF):
0 Supported formats: DSF/DSDIFF
0 Supported sampling rates: 2.8 MHz, 5.6 MHz
0 Variable bit-rate (VBR) files are supported. However,
playback times may not be displayed correctly.
0 Remote playback does not support the gapless playback.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
USB Storage Device
Basic play
1
Play music files on a USB storage device.
1. Switch the input on the TV to that assigned to the unit.
2. Plug your USB storage device with the music files into
the USB port on the front of this unit.
3. Press "USB" on the remote controller.
0 If the "USB" indicator flashes on the display, check
whether the USB storage device is plugged in properly.
0 Do not unplug the USB storage device connected to this
unit while "Connecting…" is on the display. This may
cause data corruption or malfunction.
4. Press Enter (b) on the remote controller in the next
screen. The list of folders and music files on the USB
storage device are displayed. Select the folder with the
cursors and press Enter (b) to confirm your selection.
0 To return to the previous screen, press
(d).
5. With the cursors on the remote controller, select the
music file, and then press Enter (b) to start playback.
0 The USB port of this unit conforms with the USB 2.0
standard. The transfer speed may be insufficient for
some content you play, which may cause some
interruption in sound.
a
b
c
d
2
e
f
g
h
The following remote controller operations are also possible.
(a) When the folder or file lists are not shown on one screen,
you can change the screen.
(c) Pressed during play, this button changes the displayed
track information. Pressed while a folder or file list is
displayed, this button returns you to the play screen.
(e) This button plays the previous track.
(f) This button lets you start repeat or random playback.
Pressing this button repeatedly cycles through the
repeat modes.
(g) Pressed during play this button pauses playback.
Pressed while paused, and it restarts play.
(h) This button plays the next track.
27
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
USB Storage Device Requirements
0 Note that operation is not guaranteed with all USB
storage devices.
0 This unit can use USB storage devices that comply with
the USB mass storage device class standard. The unit is
also compatible with USB storage devices using the
FAT16 or FAT32 file system formats.
0 If the USB storage device has been partitioned, each
section will be treated as an independent device.
0 Up to 20,000 tracks per folder can be displayed, and
folders may be nested up to 16 levels deep.
0 USB hubs and USB storage devices with hub functions
are not supported. Do not connect these devices to the
unit.
0 USB storage devices with security function are not
supported on this unit.
0 If you connect a USB hard disk drive to the USB port of
the unit, we recommend that you use its AC adapter to
power it.
0 Media inserted to the USB card reader may not be
available in this function. Furthermore, depending on the
USB storage device, proper reading of the contents may
not be possible.
0 We accept no responsibility whatsoever for the loss or
damage to data stored on a USB storage device when
that device is used with this unit. We recommend that you
back up your important music files beforehand.
Supported Audio Formats
For server playback and playback from a USB storage
device, this unit supports the following music file formats.
Note that sound files that are protected by copyright cannot
be played on this unit.
MP3 (.mp3/.MP3):
0 Supported formats: MPEG-1/MPEG-2 Audio Layer 3
0 Supported sampling rates: 44.1 kHz, 48 kHz
28
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR.
WMA (.wma/.WMA):
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Supported bitrates: Between 5 kbps and 320 kbps and
VBR.
0 WMA Pro/Voice/WMA Lossless formats are not
supported.
WAV (.wav/.WAV):
WAV files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AIFF (.aiff/.aif/.aifc/.afc/.AIFF/.AIF/.AIFC/.AFC):
AIFF files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/.3GP/
.3G2):
0 Supported formats: MPEG-2/MPEG-4 Audio
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR.
FLAC (.flac/.FLAC):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
Apple Lossless (.m4a/.mp4/.M4A/.MP4):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 16 bit, 24 bit
DSD (.dsf/.dff/.DSF/.DFF):
0 Supported formats: DSF/DSDIFF
0 Supported sampling rates: 2.8 MHz, 5.6 MHz
Dolby TrueHD (.vr/.mlp/.VR/.MLP):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
0 Variable bit-rate (VBR) files are supported. However,
playback times may not be displayed correctly.
0 This unit supports the gapless playback of the USB
storage device in the following conditions.
When playing WAV, FLAC and Apple Lossless, and the
same format, sampling frequency, channels and
quantization bit rate are played continuously.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
AirPlay®
1
Basic play
3
Wi-Fi
4
2
iPhone
Integra DSX-3 XXX
5
You can wirelessly enjoy the music files on an iPhone®,
iPod touch®, or iPad® connected to the same access point
as this unit.
0 Update the OS version on your iOS device to the latest
version.
1. Connect the iOS device to the access point.
2. Press NET.
3. Tap the AirPlay icon
in the control center of the iOS
device and select this unit from the list of devices
displayed, and tap "Done".
4. Play the music files on the iOS device.
0 The default status is for the Network Standby feature to
be on, so when you do steps 3 and 4 above, this unit
automatically comes on and input switches to "NET". To
reduce the amount of power consumed in standby mode,
press the
button on the remote controller, then in the
Setup menu displayed set "5. Hardware" – "Power
Management" – "Network Standby" to "Off".
0 Due to the characteristics of AirPlay wireless technology,
the sound produced on this unit may slightly be behind
the sound played on the AirPlay-enabled device.
You can also play back music files on the computer with
iTunes (Ver. 10.2 or later). Before operation, make sure this
unit and the PC are connected to the same network, then
press NET on this unit. Next, click the AirPlay icon
in
iTunes, select this unit from the list of devices displayed,
and start play of a music file.
29
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
BLUETOOTH® Playback
Pairing
Pairing
Playing Back
1
1
1. When you press the
button on the remote controller,
"Now Pairing..." is displayed on this unit's display, and the
pairing mode is enabled.
Integra DSX-3 XXX
2
2
2. Enable (turn on) the BLUETOOTH function of the
BLUETOOTH enabled device, then select this unit from
amongst the devices displayed. If a password is
requested, enter "0000".
0 To connect another BLUETOOTH enabled device, press
and hold the
button until "Now Pairing..." is displayed,
then perform step 2 above. This unit can store the data of
up to eight paired devices.
0 The coverage area is 15 meters (48 feet). Note that
connection is not always guaranteed with all
BLUETOOTH enabled devices.
Playing Back
Integra DSX-3 XXX
30
1. When the unit is on, perform the connection procedure
on the BLUETOOTH enabled device.
2. The input selector on this unit automatically switches to
"BLUETOOTH".
3. Play the music files. Increase the volume of the
BLUETOOTH enabled device to an appropriate level.
0 Due to the characteristics of BLUETOOTH wireless
technology, the sound produced on this unit may slightly
be behind the sound played on the BLUETOOTH
enabled device.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Listening to the FM Radio
Tuning Automatically
1
1. Press Tuner on the remote controller.
2. Press Mode (d) on the remote controller so that "AUTO"
appears on the display.
3. When you press the cursor / buttons (a) on the
remote controller, automatic tuning starts, and searching
stops when a station is found. When tuned into a radio
station, the "TUNED" indicator on the display lights.
When tuned into a stereo FM station, the "FM STEREO"
indicator lights.
0 No sound is output while the "TUNED" indicator is off.
When FM broadcasts reception is poor
Radio waves may be weak depending on the building
structure and environmental conditions. In that case,
perform the procedure as explained below in "Tuning
Manually" to manually select the desired station.
a
Tuning Manually
b
c
d
1. Press Tuner on the remote controller.
2. Press Mode (d) on the remote controller to turn off
"AUTO" on the display.
3. While pressing the cursor / buttons (a) on the remote
controller, select the desired radio station.
0 The frequency changes by 1 step each time you press
the button. The frequency changes continuously if the
button is held down and stops when the button is
released. Tune by looking at the display.
To return to the auto tuning mode
Press Mode (d) on the remote controller again so that
"AUTO" appears on the display. The unit tunes
automatically into a radio station.
the frequency step for your area. Note that when this setting
is changed, all radio presets are deleted.
Presetting a Radio Station
It allows you to register up to 40 of your favorite radio
stations. Registering radio stations in advance allows you to
tune into your radio station of choice directly.
1. Tune into the radio station you want to register.
2. Press Memory (c) on the remote controller so that the
preset number on the display flashes.
3. While the preset number is flashing (about 8 seconds),
repeatedly press the cursor / buttons (a) on the
remote controller to select a number between 1 and 40.
4. Press Memory (c) on the remote controller again to
register the station. When registered, the preset number
stops flashing.
Selecting a Preset Radio Station
1. Press Tuner on the remote controller.
2. Press the cursor / buttons (a) on the remote
controller to select a preset number.
Deleting a Preset Radio Station
1. Press Tuner on the remote controller.
2. Press the cursor / buttons (a) on the remote
controller to select the preset number to delete.
3. After pressing Memory (c) on the remote controller, press
Clear (b) while the preset number is flashing to delete the
preset number.
0 When deleted, the number on the display goes off.
Frequency step setting
Press the
button on the remote controller to select "6
Miscellaneous" – "Tuner" – "FM Frequency Step" and select
31
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Listening Modes
Selecting Listening Modes
Input source & volume
Select the optimum listening mode for movies, TV, music,
and games by repeatedly pressing the Movie/TV, Music,
and Game buttons.
a
1. During play, press one of the three buttons (b) on the
remote controller.
2. Press the selected button repeatedly to switch the modes
displayed on the display of the unit.
Listening mode
Signal format
b
For details on the effects of each of the listening modes see
"Listening Mode Effects" (P33). For listening modes
selectable for each of the audio formats in the input signals,
refer to "Selectable listening modes" (P35).
The listening mode last selected for the source is
remembered for each of the Movie/TV, Music, and Game
buttons. If content you play is not supported by the listening
mode you selected last, the listening mode that is standard
for that content is selected automatically.
Press
(a) repeatedly to switch the display of the main
unit in order of:
32
The display changes few
seconds later.
Sampling frequency
Input signal resolution
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Listening Mode Effects
Updating of listening modes
We plan to provide support for the Dolby Atmos and DTS:X
audio format through firmware updates for this unit. This
means that the selectable listening modes depend on the
version of firmware.
On firmware version before Dolby Atmos support
0 Dolby Pro Logic Ⅱ -related modes can be selected.
On firmware version after Dolby Atmos support
0 Dolby Atmos, Dolby Surround, and Surround Enhancer
can be selected. (Dolby Pro Logic Ⅱ -related modes
cannot be selected after updating.) Also, when Surround
Enhancer can be selected, T-D (Theater-Dimensional)
cannot be selected.
On firmware version before DTS:X support
0 You can select Neo:6 Cinema and Neo:6 Music.
On firmware version after DTS:X support
0 You can select DTS:X and DTS Neural:X. (You cannot
select Neo:6 Cinema and Neo:6 Music after updating.)
In alphabetical order
AllCh Stereo
Ideal for background music, this mode fills the entire
listening area with stereo sound from the front, surround,
and surround back speakers.
Direct
This listening mode can be selected for all input signals.
Processing that affects sound quality is shut down so sound
closer to the original is reproduced. Speakers play the
sound field according to the number of channels in the input
signal, so there would be output from only the front
speakers for a two-channel signal, for example.
Dolby Atmos
This mode faithfully reproduces the sound design recorded
in the Dolby Atmos audio format.
The Dolby Atmos audio format has been implemented in
movie theaters equipped with the latest facilities and
enables a revolutionary sound experience in home theaters.
Unlike existing surround systems, Dolby Atmos doesn't rely
on channels, but rather enables the accurate placement of
sound objects that have independent motion in a threedimensional space with even greater clarity. Dolby Atmos is
an optional audio format on Blu-ray Discs and achieves a
three-dimensional sound field by introducing a sound field
above the listener.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
Dolby D (Dolby Digital)
This mode faithfully reproduces the sound design recorded
in the Dolby Digital audio format.
Dolby Digital is a multi-channel digital format developed by
Dolby Laboratories, Inc. widely adopted for use in movie
production. It is also a standard audio format on DVD-Video
and Blu-ray Discs. It is possible to record a maximum of 5.1
channels on a DVD-Video or Blu-ray Disc; two front
channels, a center channel, two surround channels, and the
LFE channel dedicated to the bass region (sound elements
for the subwoofer).
0 To enable transfer of this audio format, connect via digital
cable and set audio output on the player to bitstream
output.
Dolby D + (Dolby Digital Plus)
This mode faithfully reproduces the sound design recorded
in the Dolby Digital Plus audio format.
The Dolby Digital Plus format is a revision based on Dolby
Digital, increasing the number of channels and endeavoring
to improve sound quality by giving more flexibility in data bit
rates. Dolby Digital Plus is used as an optional audio format
on Blu-ray Discs, based on 5.1ch, but with additional
channels such as the surround back channel added for a
maximum of 7.1ch.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
Dolby PL Ⅱ (Dolby Pro Logic Ⅱ )
These listening modes allow you to expand the playback
signal to 5.1 channels to suit the connected speaker
configuration when the input signal is 2 channel.
Broadening the sound field provides you with a seamless
sound with more depth and realism. Along with CD and
movie sources, games can also benefit from the vivid sound
localization. Choose from a mode ideal for movies (Movie),
a mode ideal for music (Music), and a mode ideal for
gaming (Game).
Dolby Surround
These listening modes allow you to expand the playback
signal to multiple channels to suit the connected speaker
configuration when the input signal is 2 channel or 5.1
channel. Along with past speaker setups, this is also
compatible with playback systems for Dolby Atmos that
include Dolby speaker technology.
Dolby TrueHD
This mode faithfully reproduces the sound design recorded
in the Dolby TrueHD audio format.
The Dolby TrueHD audio format is a reversible format
expanded based on the lossless compression technology
referred to as MLP, and it makes it possible to faithfully
reproduce the master audio recorded in the studio. Dolby
TrueHD is used as an optional audio format on Blu-ray
Discs, based on 5.1ch, but with additional channels such as
the surround back channel added for a maximum of 7.1ch.
7.1ch is recorded at 96 kHz/24bit, and 5.1ch is recorded at
192 kHz/24bit.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
33
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
output.
DSD
Mode suitable for playing sources recorded in DSD.
0 This unit supports DSD signals input through HDMI IN.
However, depending on the connected player, better
sound is possible when output from the PCM output of
the player.
0 This listening mode cannot be selected if the output
setting on your Blu-ray Disc/DVD player is not set to
DSD.
DTS
This mode faithfully reproduces the sound design recorded
in the DTS audio format.
The DTS audio format is a multi-channel digital format
developed by DTS, Inc. This format is an optional audio
format on DVD-Video and a standard on Blu-ray Discs. It
enables recording of 5.1 channels; two front channels, a
center channel, two surround channels, and the LFE
channel dedicated to the bass region (sound elements for
the subwoofer). The content is recorded with a rich volume
of data, with maximum sampling rate of 48 kHz at a
resolution of 24 bits and a bit rate of 1.5 Mbps.
0 To enable transfer of this audio format, connect via digital
cable and set audio output on the player to bitstream
output.
DTS 96/24
This mode faithfully reproduces the sound design recorded
in the DTS 96/24 audio format.
The DTS 96/24 format is an optional audio format on DVDVideo and Blu-ray Discs. It enables recording of 5.1
channels; two front channels, a center channel, two
surround channels, and the LFE channel dedicated to the
bass region (sound elements for the subwoofer). Detailed
reproduction is achieved by recording the content at a
sampling rate of 96 kHz at a resolution of 24 bits.
0 To enable transfer of this audio format, connect via digital
34
cable and set audio output on the player to bitstream
output.
DTS Express
This mode faithfully reproduces the sound design recorded
in the DTS Express audio format.
DTS Express is used as an optional audio format on Blu-ray
Discs, based on 5.1ch, but with channels such as the
surround back channel added for a maximum of 7.1ch. It
also supports low bit rates.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
DTS-HD HR (DTS-HD High Resolution Audio)
This mode faithfully reproduces the sound design recorded
in the DTS-HD High Resolution Audio audio format.
DTS-HD High Resolution Audio is used as an optional
audio format on Blu-ray Discs, based on 5.1ch, but with
additional channels such as the surround back channel
added for a maximum of 7.1ch. It can be recorded at a
sampling rate of 96 kHz with a resolution of 24 bits.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
DTS-HD MSTR (DTS-HD Master Audio)
This mode faithfully reproduces the sound design recorded
in the DTS-HD Master Audio audio format.
DTS-HD Master Audio is used as an optional audio format
on Blu-ray Discs, based on 5.1ch, but with additional
channels such as the surround back channel added for a
maximum of 7.1ch, recorded using lossless audio
reproduction technology. 96 kHz/24bit is supported with
7.1ch, and 192 kHz/24bit is supported with 5.1ch.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
DTS Neo:6
These listening modes allow you to expand the playback
signal to 5.1 channels to suit the connected speaker
configuration when the input signal is 2 channel. It offers
full-bandwidth on all channels, with great independence
between the channels. There are two variants for this mode:
Neo:6 Cinema which is ideal for movies and Neo:6 Music
which is ideal for music.
DTS Neural:X
This listening mode allows you to expand the playback
signal to suit the connected speaker configuration when the
input signal is 2 channels or 5.1 channels.
DTS:X
This mode faithfully reproduces the sound design recorded
in the DTS:X audio format.
The DTS:X audio format is a combination of the mixing
methodology based on past channel based formats and
object based dynamic audio mixing, and it is characterized
by the precise positioning of sounds and the ability to
express movement.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
Full Mono
In this mode, all speakers output the same sound in mono,
so the sound you hear is the same regardless of where you
are within the listening room.
Game-Action
In this mode, sound localization is distinct with emphasis on
bass.
Game-Rock
In this mode, sound pressure is emphasized to heighten live
feel.
Game-RPG
In this mode, the sound has a dramatic feel with a similar
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
atmosphere to Orchestra mode.
listener's left and right ears.
Selectable listening modes
Game-Sports
Suitable for audio source with much reverberation.
TV Logic
Suitable for TV shows produced in a TV studio. This mode
enhances the surround effects to the entire sound to give
clarity to voices and create a realistic acoustic image.
You can select a variety of listening modes to suit the audio
format of the signal being input.
0 Listening modes available when headphones are
connected are: Mono, Direct and Stereo.
Unplugged
Suitable for acoustic instruments, vocals and jazz. This
mode emphasizes the front stereo image, giving the
impression of being right in front of the stage.
Updating of listening modes
We plan to provide support for the Dolby Atmos and DTS:X
audio format through firmware updates for this unit. This
means that the selectable listening modes depend on the
version of firmware.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or use it to separately reproduce soundtracks in
two different languages recorded in the left and right
channels of some movies. It is also suitable for DVDs or
other sources containing multiplexed audio.
Multich (Multichannel)
Mode suitable for playing sources recorded in multichannel
PCM.
Orchestra
Suitable for classical or operatic music. This mode
emphasizes the surround channels in order to widen the
stereo image, and simulates the natural reverberation of a
large hall.
Stereo
In this mode, sound is output from the front left and right
speakers and subwoofer.
Studio-Mix
Suitable for rock or pop music. Listening to music in this
mode creates a lively sound field with a powerful acoustic
image, like being at a club or rock concert.
On firmware version before Dolby Atmos support
0 Dolby Pro Logic Ⅱ -related modes can be selected.
On firmware version after Dolby Atmos support
0 Dolby Atmos, Dolby Surround, and Surround Enhancer
can be selected. (Dolby Pro Logic Ⅱ -related modes
cannot be selected after updating.) Also, when Surround
Enhancer can be selected, T-D (Theater-Dimensional)
cannot be selected.
On firmware version before DTS:X support
0 You can select Neo:6 Cinema and Neo:6 Music.
On firmware version after DTS:X support
0 You can select DTS:X and DTS Neural:X. (You cannot
select Neo:6 Cinema and Neo:6 Music after updating.)
Surround Enhancer
This mode allows you to enjoy sound with a rich sound field,
enveloping you naturally without relying on reflections from
walls. A virtual surround channel is created to give you a
broader sound field.
T-D (Theater-Dimensional)
In this mode, you can enjoy a virtual playback of
multichannel surround sound even with only two or three
speakers. This works by controlling how sounds reach the
35
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Movie/TV button
This is a list of listening modes you can select according to
the audio format of the input signal.
Input Format
Listening Mode
Analog
Direct
Mono
Dolby Surround
Surround Enhancer
PL Ⅱ Movie * 1
Neo:6 Cinema * 1
DTS Neural:X
TV Logic * 2
AllCh Stereo * 1
Full Mono * 1
T-D
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
36
Input Format
Listening Mode
Input Format
Listening Mode
PCM
Music files (except DSD/
Dolby TrueHD)
Direct
Multich PCM
Direct
Mono
Multich * 1
Dolby Surround
Dolby Surround
Surround Enhancer
Surround Enhancer
PL Ⅱ Movie
DTS Neural:X
*1
Neo:6 Cinema * 1
TV Logic * 2
DTS Neural:X
AllCh Stereo * 1
TV Logic * 2
Full Mono * 1
AllCh Stereo
*1
Full Mono * 1
T-D
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
T-D
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
DSD
Direct
Dolby D
Listening Mode
Input Format
Listening Mode
Direct
Dolby D+
Direct
DSD * 1 * 2
Dolby D * 1 * 2
Dolby D+ * 1 * 2
Dolby Surround
Dolby Surround
Dolby Surround
Surround Enhancer
Surround Enhancer
Surround Enhancer
PL Ⅱ Movie
PL Ⅱ Movie
PL Ⅱ Movie * 3
*3
*3
Neo:6 Cinema * 3
Neo:6 Cinema * 3
Neo:6 Cinema * 3
DTS Neural:X
TV Logic
TV Logic * 4
TV Logic * 4
AllCh Stereo * 2
AllCh Stereo * 2
Full Mono
Full Mono * 2
AllCh Stereo
*2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is monaural or
2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
Input Format
Listening Mode
Dolby Atmos
Direct
*4
*2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
Dolby Atmos
Surround Enhancer
TV Logic
AllCh Stereo
Full Mono
T-D
37
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
Dolby TrueHD
Direct
DTS
Input Format
Listening Mode
Direct
DTS 96/24
Direct
Dolby TrueHD * 1 * 2
DTS * 1 * 2
Dolby Surround
PL Ⅱ Movie
Surround Enhancer
Neo:6 Cinema * 3
Neo:6 Cinema * 3
PL Ⅱ Movie
DTS 96/24 * 1 * 2
*3
PL Ⅱ Movie * 3
DTS Neural:X
DTS Neural:X
Neo:6 Cinema * 3
TV Logic * 4
TV Logic * 4
TV Logic
AllCh Stereo
*3
*4
AllCh Stereo * 2
Full Mono
*2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
38
Listening Mode
*2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
AllCh Stereo * 2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
DTS Express
Direct
DTS-HD HR
Listening Mode
Input Format
Listening Mode
Direct
DTS-HD MSTR
Direct
DTS Express * 1 * 2
DTS-HD HR * 1 * 2
DTS-HD MSTR * 1 * 2
PL Ⅱ Movie
PL Ⅱ Movie
PL Ⅱ Movie * 3
*3
*3
Neo:6 Cinema * 3
Neo:6 Cinema * 3
Neo:6 Cinema * 3
DTS Neural:X
DTS Neural:X
DTS Neural:X
TV Logic * 4
TV Logic * 4
TV Logic * 4
AllCh Stereo
*2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
AllCh Stereo
AllCh Stereo * 2
*2
Full Mono * 2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
Input Format
Listening Mode
DTS:X
Direct
DTS:X
TV Logic * 1
AllCh Stereo * 2
Full Mono * 2
T-D
* 1: Surround speakers need to be installed.
* 2: A center speaker or surround speakers need to be installed.
39
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Music button
This is a list of listening modes you can select according to
the audio format of the input signal.
Input Format
Listening Mode
Analog
Direct
Stereo
Dolby Surround
Surround Enhancer
PL Ⅱ Music * 1
Neo:6 Music * 1
DTS Neural:X
Orchestra * 2
Unplugged * 2
Studio-Mix * 2
AllCh Stereo * 1
Full Mono * 1
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
40
Input Format
Listening Mode
Input Format
Listening Mode
PCM
Music files (except DSD/
Dolby TrueHD)
Direct
Multich PCM
Direct
Stereo
Stereo
Dolby Surround
Multich * 1
Surround Enhancer
Dolby Surround
PL Ⅱ Music
Surround Enhancer
*1
Neo:6 Music * 1
DTS Neural:X
DTS Neural:X
Orchestra * 2
Orchestra * 2
Unplugged * 2
Unplugged
Studio-Mix * 2
*2
Studio-Mix * 2
AllCh Stereo * 1
AllCh Stereo
Full Mono * 1
*1
Full Mono * 1
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
DSD
Listening Mode
Direct
Input Format
Dolby Atmos
Listening Mode
Input Format
Listening Mode
Direct
Dolby D
Direct
Stereo
Stereo
Stereo
DSD * 1 * 2
Dolby Atmos
Dolby D * 1 * 2
Dolby Surround
Surround Enhancer
Surround Enhancer
Orchestra
PL Ⅱ Music * 3
Unplugged
Neo:6 Music * 3
Studio-Mix
DTS Neural:X
AllCh Stereo
Orchestra * 4
Full Mono
Unplugged * 4
Studio-Mix
*4
AllCh Stereo * 2
Full Mono * 2
* 1: Cannot be selected when the input format is monaural or
2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
Dolby Surround
Surround Enhancer
PL Ⅱ Music * 3
Neo:6 Music * 3
Orchestra * 4
Unplugged * 4
Studio-Mix * 4
AllCh Stereo * 2
Full Mono * 2
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
41
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
Dolby D+
Direct
Dolby TrueHD
Stereo
Dolby D+
Input Format
Listening Mode
Direct
DTS
Direct
Stereo
*1*2
Stereo
Dolby TrueHD
*1*2
DTS * 1 * 2
Dolby Surround
Dolby Surround
PL Ⅱ Music * 3
Surround Enhancer
Surround Enhancer
Neo:6 Music * 3
PL Ⅱ Music * 3
PL Ⅱ Music * 3
DTS Neural:X
Neo:6 Music
Neo:6 Music
Orchestra * 4
*3
*3
Orchestra * 4
Orchestra * 4
Unplugged * 4
Unplugged
Unplugged
Studio-Mix * 4
*4
*4
Studio-Mix * 4
Studio-Mix * 4
AllCh Stereo * 2
AllCh Stereo
AllCh Stereo
Full Mono * 2
*2
Full Mono * 2
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
42
Listening Mode
*2
Full Mono * 2
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
DTS 96/24
Direct
DTS Express
Stereo
Listening Mode
Input Format
Listening Mode
Direct
DTS-HD HR
Direct
Stereo
DTS 96/24
*1*2
Stereo
DTS Express
*1*2
DTS-HD HR * 1 * 2
PL Ⅱ Music * 3
PL Ⅱ Music * 3
PL Ⅱ Music * 3
Neo:6 Music
Neo:6 Music
Neo:6 Music * 3
*3
*3
DTS Neural:X
DTS Neural:X
DTS Neural:X
Orchestra
Orchestra
Orchestra * 4
*4
*4
Unplugged * 4
Unplugged * 4
Unplugged * 4
Studio-Mix
Studio-Mix
Studio-Mix * 4
*4
*4
AllCh Stereo * 2
AllCh Stereo * 2
AllCh Stereo * 2
Full Mono
Full Mono
Full Mono * 2
*2
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
*2
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
43
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
Listening Mode
DTS-HD MSTR
Direct
DTS:X
Direct
Stereo
Stereo
DTS-HD MSTR
*1*2
DTS:X
PL Ⅱ Music * 3
Orchestra * 1
Neo:6 Music
Unplugged * 1
*3
DTS Neural:X
Studio-Mix * 1
Orchestra * 4
AllCh Stereo * 2
Unplugged * 4
Full Mono * 2
Studio-Mix * 4
AllCh Stereo * 2
Full Mono * 2
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
* 1: Surround speakers need to be installed.
* 2: A center speaker or surround speakers need to be installed.
Game button
This is a list of listening modes you can select according to
the audio format of the input signal.
Input Format
Listening Mode
Analog
Direct
Dolby Surround
Surround Enhancer
PL Ⅱ Game * 1
DTS Neural:X
Game-RPG * 2
Game-Action * 2
Game-Rock * 2
Game-Sports * 2
AllCh Stereo * 1
Full Mono * 1
T-D
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
44
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
PCM
Music files (except DSD/
Dolby TrueHD)
Direct
Multich PCM
Listening Mode
Input Format
Listening Mode
Direct
DSD
Direct
Dolby Surround
Multich * 1
DSD * 1 * 2
Surround Enhancer
Dolby Surround
Dolby Surround
PL Ⅱ Game * 1
Surround Enhancer
Surround Enhancer
DTS Neural:X
DTS Neural:X
PL Ⅱ Game * 3
Game-RPG * 2
Game-RPG * 2
DTS Neural:X
Game-Action
Game-Action
Game-RPG * 4
*2
*2
Game-Rock * 2
Game-Rock * 2
Game-Action * 4
Game-Sports
Game-Sports
Game-Rock * 4
*2
*2
AllCh Stereo * 1
AllCh Stereo * 1
Game-Sports * 4
Full Mono
Full Mono
AllCh Stereo * 2
*1
T-D
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
*1
T-D
* 1: A center speaker or surround speakers need to be installed.
* 2: Surround speakers need to be installed.
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is monaural or
2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
45
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
Dolby Atmos
Direct
Dolby D
Listening Mode
Input Format
Listening Mode
Direct
Dolby D+
Direct
Dolby Atmos
Dolby D * 1 * 2
Dolby D+ * 1 * 2
Surround Enhancer
Dolby Surround
Dolby Surround
Game-RPG
Surround Enhancer
Surround Enhancer
Game-Action
PL Ⅱ Game
PL Ⅱ Game * 3
Game-Rock
Game-RPG * 4
Game-RPG * 4
Game-Sports
Game-Action
Game-Action * 4
AllCh Stereo
Game-Rock * 4
Game-Rock * 4
Full Mono
Game-Sports
Game-Sports * 4
T-D
AllCh Stereo * 2
AllCh Stereo * 2
Full Mono
Full Mono * 2
*3
*4
*4
*2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
46
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
Dolby TrueHD
Direct
DTS
Listening Mode
Input Format
Listening Mode
Direct
DTS 96/24
Direct
Dolby TrueHD * 1 * 2
DTS * 1 * 2
Dolby Surround
PL Ⅱ Game
Surround Enhancer
DTS Neural:X
DTS Neural:X
PL Ⅱ Game
Game-RPG
Game-RPG * 4
*3
DTS 96/24 * 1 * 2
*3
*4
PL Ⅱ Game * 3
Game-RPG * 4
Game-Action * 4
Game-Action * 4
Game-Action
Game-Rock
Game-Rock * 4
*4
*4
Game-Rock * 4
Game-Sports * 4
Game-Sports * 4
Game-Sports
AllCh Stereo
AllCh Stereo * 2
*4
AllCh Stereo * 2
Full Mono
*2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
*2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
47
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
Input Format
DTS Express
Direct
DTS-HD HR
Input Format
Listening Mode
Direct
DTS-HD MSTR
Direct
DTS Express * 1 * 2
DTS-HD HR * 1 * 2
DTS-HD MSTR * 1 * 2
PL Ⅱ Game
PL Ⅱ Game
PL Ⅱ Game * 3
*3
*3
DTS Neural:X
DTS Neural:X
DTS Neural:X
Game-RPG
Game-RPG
Game-RPG * 4
*4
*4
Game-Action * 4
Game-Action * 4
Game-Action * 4
Game-Rock
Game-Rock
Game-Rock * 4
*4
*4
Game-Sports * 4
Game-Sports * 4
Game-Sports * 4
AllCh Stereo
AllCh Stereo
AllCh Stereo * 2
*2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
48
Listening Mode
*2
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
Full Mono * 2
T-D
* 1: Cannot be selected when the input format is 2 ch.
* 2: A center speaker or surround speakers need to be installed.
* 3: Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
* 4: Surround speakers need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Input Format
Listening Mode
DTS:X
Direct
DTS:X
Game-RPG * 1
Game-Action * 1
Game-Rock * 1
Game-Sports * 1
AllCh Stereo * 2
Full Mono * 2
T-D
* 1: Surround speakers need to be installed.
* 2: A center speaker or surround speakers need to be installed.
49
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Quick Menu
1
By pressing the Q button on the remote controller during
play, you can adjust frequently used settings, such as the
sound quality, using on-screen menus.
1. Press Q on the remote controller.
2. After the Quick Menu is displayed, select the content with
/ on the remote controller and press Enter to confirm
your selection.
Quick Menu
■ AccuEQ
AccuEQ Room Calibration: Enable or disable the
equalizer function that corrects for distortion caused by the
acoustic environment of the room. If this is to be enabled,
then normally you should select "On (All Channels)", and to
disable just the front speakers you should select "On
(Except Front Left / Right)". The setting can be separately
set to each input selector.
BD/DVD
Tone
Bass
Level
Treble
AccuEQ
Other
0 Change the initial values for each of the settings with the
cursors /.
0 To return to the previous screen, press
.
3. To exit the settings, press Q.
■ Tone
Bass: Enhance or moderate the bass range of the front
speakers.
Treble: Enhance or moderate the treble range of the front
speakers.
0 It cannot be set if the listening mode is Direct.
■ Level
Center: Adjust the speaker level of the center speaker
while listening to some sound.
Subwoofer: Adjust the speaker level of the subwoofer
while listening to some sound.
0 The adjustment you made will be reset to the previous
status when you turn the unit to standby mode.
Equalizer: Select "Preset 1" to "Preset 3" configured in "2.
Speaker" - "Equalizer Settings" (P58) in the Setup menu.
The same sound field setting is applied all ranges when set
to "Off".
Cinema Filter: Adjust the soundtrack that was processed to
enhance its high pitch range, in order to make it suitable for
home theater. This function can be used in the following
listening modes: Dolby Digital, Dolby Digital Plus, Dolby PL
II Movie, Dolby Surround, Dolby TrueHD, Multichannel,
DTS, DTS 96/24, DTS-HD High Resolution Audio, DTS-HD
Master Audio, DTS Neural:X, DTS Express, Neo:6 Cinema,
and DSD.
0 It cannot be set if the listening mode is Direct.
■ Other
A/V Sync: If the video is behind the audio, you can delay
the audio to offset the gap. Different settings can be set for
each input selector.
0 It cannot be set if the listening mode is Direct.
Music Optimizer: Improve the quality of the compressed
audio. Playback sound of lossy compressed files such as
MP3 will be improved. The setting can be separately set to
each input selector. The setting is effective in the signals of
48 kHz or less. The setting is not effective in the bitstream
signals.
0 It cannot be set if the listening mode is Direct.
Late Night: Make small sounds easily heard. It is useful
50
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
when you need to reduce the volume while watching a
movie late night. You can enjoy the effect only when playing
Dolby series and DTS series input signals.
0 The setting cannot be used in the following cases.
– If "3. Audio Adjust" - "Dolby" - "Loudness
Management" (P59) in the Setup menu is set to
"Off" when playing Dolby Digital Plus or Dolby TrueHD
– When the input signal is DTS and "Dialog Control" is
other than 0 dB
Panorama: Broaden the sound field laterally when playing
in the Dolby Pro Logic Ⅱ Music listening mode.
Dimension: Adjust the depth of the sound field in the front
to back direction when playing in the Dolby Pro Logic Ⅱ
Music listening mode. Set a small number to move the
sound towards the front. Set a large number to move the
sound back.
version of firmware.
On firmware version before Dolby Atmos support
0 Panorama, Dimension, Center Width can be set.
On firmware version after Dolby Atmos support
0 You cannot set Panorama, Dimension, Center Width after
updating.
On firmware version before DTS:X support
0 Center Image can be set.
On firmware version after DTS:X support
0 You can set Dialog Control. (You cannot set Center
Image after updating.)
Center Width: Adjust the width of the front sound field
when playing in the Dolby Pro LogicⅡMusic listening mode.
Set a small number to concentrate sound in the middle. Set
a large number to distribute the central sound out to the left
and right.
Dialog Control: You can increase the dialog portion of the
audio in 1 dB steps up to 6 dB so that you can make dialog
easier to hear over background noise.
0 This cannot be set for content other than DTS:X.
0 The effect may not be selectable with some content.
Center Image: Adjust the width of the front sound field
when playing in the DTS Neo:6 Music listening mode. Set a
small number to concentrate sound in the middle. Set a
large number to distribute the central sound out to the left
and right.
We plan to provide support for the Dolby Atmos and DTS:X
audio format through firmware updates for this unit. This
means that the selectable listening modes depend on the
51
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Other Functions
Playing audio and video from separate
sources
It is possible to play audio and video from different sources.
For example, you can play audio from the CD player and
video from the BD/DVD player. The procedure in this case
is as follows:
1. Press BD/DVD on the remote controller.
2. Press CD on the remote controller.
3. Start playback on the BD/DVD player and CD player.
Perform the following steps to play the video from a different
source to suit the audio from a NET or BLUETOOTH input
source.
1. Press NET or
on the remote controller to play the
audio.
2. Press Mode on the remote controller and the video input
select immediately preceding this operation can be
played.
3. Start play of the video input source.
4. Each press of Mode displays or turns off the video.
52
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Supplementary information for player functions
Supplementary information
Due to firmware (the software for the system) updates after
you make your purchase or firmware changes during
production of the product, there may be additions or
changes to the features available compared to what is in the
instruction manual.
For information about player functions that have been
added or changed, see the following references.
Supplementary information for player functions
>>> Click here <<<
53
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Setup Menu
Advanced Setup
1
2
The unit allows you to configure advanced settings to provide you with an even better
experience.
1. Switch the input on the TV to that assigned to the unit.
2. Press
on the remote controller.
3. After the Setup menu is displayed, select the content with / on the remote controller
and press Enter to confirm your selection.
Setup
1. Input/Output Assign
1. TV Out / OSD
2. Speaker
2. HDMI Input
3. Audio Adjust
3. Digital Audio Input
4. Source
4. Analog Audio Input
5. Hardware
6. Miscellaneous
TV's remote controller
0 Change the initial values for each of the settings with the cursors /.
0 To return to the previous screen, press
.
4. To exit the settings, press .
1. Input/Output Assign
■ 1. TV Out / OSD
54
1080p -> 4K Upscaling
When using a TV that supports 4K, video signals input at 1080p
can be automatically upscaled to 4K for output.
"Off (Default Value)": When not using this function
"Auto": Use this function
0 Select "Off" if your TV does not support 4K.
Super Resolution
When you have set "1080p -> 4K Upscaling" to "Auto", you can
select the degree of video signal correction from "Off" and
between "1" (weak) and "3" (strong).
OSD Language
Select the on-screen display language.
English, German, French, Spanish, Italian, Dutch, Swedish,
Russian, Chinese
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Impose OSD
Screen Saver
Set whether or not to display the information on the TV when the
volume is adjusted or input is changed, for example.
"On (Default Value)": OSD displayed on the TV
"Off": OSD not displayed on the TV
0 OSD may not be displayed depending on the input signal
even if "On" is selected. If the operation screen is not
displayed, change the resolution of the connected device.
CD
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the CD input selector. If you do not assign a
jack, select "-----". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "-----"
first. (Default Value is "-----")
TV
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the TV input selector. If you do not assign a jack,
select "-----". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "-----"
first. (Default Value is "-----")
PHONO
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the PHONO input selector. If you do not assign
a jack, select "-----". To select an HDMI IN jack already assigned
to another input selector, change the input selector setting to "----" first. (Default Value is "-----")
Set the time to start the screen saver.
Select a value from "3 minutes (Default Value)", "5 minutes", "10
minutes" and "Off".
■ 2. HDMI Input
You can change input assignment between the input selectors and HDMI IN jacks.
BD/DVD
CBL/SAT
GAME
STRM BOX
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the BD/DVD input selector. If you do not assign
a jack, select "-----". To select an HDMI IN jack already assigned
to another input selector, change the input selector setting to "----" first. (Default Value is "HDMI 1 (HDCP 2.2)")
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the CBL/SAT input selector. If you do not assign
a jack, select "-----". To select an HDMI IN jack already assigned
to another input selector, change the input selector setting to "----" first. (Default Value is "HDMI 2 (HDCP 2.2)")
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the GAME input selector. If you do not assign a
jack, select "-----". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "-----"
first. (Default Value is "HDMI 4 (HDCP 2.2)")
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the STRM BOX input selector. If you do not
assign a jack, select "-----". To select an HDMI IN jack already
assigned to another input selector, change the input selector
setting to "-----" first. (Default Value is "HDMI 3 (HDCP 2.2)")
■ 3. Digital Audio Input
You can change input assignment between the input selectors and DIGITAL IN COAXIAL/
OPTICAL jacks. If you do not assign a jack, select "-----".
BD/DVD
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the BD/DVD input selector. (Default Value is "-----")
CBL/SAT
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the CBL/SAT input selector. (Default Value is "-----")
GAME
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the GAME input selector. (Default Value is "-----")
STRM BOX
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the STRM BOX input selector. (Default Value is "-----")
CD
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the CD input selector. (Default Value is "COAXIAL")
TV
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the TV input selector. (Default Value is "OPTICAL")
PHONO
"COAXIAL", "OPTICAL" : Assign a desired DIGITAL IN jack to
the PHONO input selector. (Default Value is "-----")
55
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
0 Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32kHz,
44.1kHz, 48kHz, 88.2kHz, 96kHz/16bit, 20bit, and 24bit.
■ 4. Analog Audio Input
You can change input assignment between the input selectors and AUDIO IN jacks. If you
do not assign a jack, select "-----".
BD/DVD
"AUDIO 1" to "AUDIO 2": Assign a desired AUDIO IN jack to the
BD/DVD input selector. (Default Value is "AUDIO 1")
CBL/SAT
"AUDIO 1" to "AUDIO 2": Assign a desired AUDIO IN jack to the
CBL/SAT input selector. (Default Value is "AUDIO 2")
GAME
"AUDIO 1" to "AUDIO 2": Assign a desired AUDIO IN jack to the
GAME input selector. (Default Value is "-----")
STRM BOX
"AUDIO 1" to "AUDIO 2": Assign a desired AUDIO IN jack to the
STRM BOX input selector. (Default Value is "-----")
CD
"AUDIO 1" to "AUDIO 2": Assign a desired AUDIO IN jack to the
CD input selector. (Default Value is "-----")
TV
"AUDIO 1" to "AUDIO 2": Assign a desired AUDIO IN jack to the
TV input selector. (Default Value is "-----")
PHONO
(Default Value is "PHONO") The setting cannot be changed.
2. Speaker
You can make changes to the connection environment of the speakers and change the
volume level. Settings are automatically configured if you use AccuEQ Room Calibration.
This setting cannot be selected if headphones are connected or audio is output from the
speakers of the TV because "5. Hardware" - "HDMI" - "Audio TV Out" is set to "On".
■ 1. Configuration
Speaker Channels
Select from "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch (default value)",
"2.1.2 ch", or "3.1.2 ch" to suit the number of speaker channels
connected.
Subwoofer
Set whether a subwoofer is connected or not.
"Yes (Default Value)": When subwoofer is connected
"No": When subwoofer is not connected
Height Speaker
Set the speaker type if height speakers are connected to the
SURROUND terminal. Select from "Front High", "Top Middle
(default value)", or "Dolby Speaker (Front)" to suit the type and
layout of the connected speakers.
0 If an item cannot be selected even though connection is
correct, check that the settings in "Speaker Channels"
matches the number of connected channels.
■ 2. Crossover
Front
56
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 If "Configuration" - "Subwoofer" is set to "No", "Front" will be
fixed to "Full Band" and the low pitched range of the other
channels will be output from the front speakers. Refer to the
instruction manual of your speakers to make the setting.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Center
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
Height
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
Surround
LPF of LFE
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
Set the low-pass filter for LFE (low-frequency effect) signals in
order to pass lower frequency signals than the set value and
thus cancel unwanted noises. The low-pass filter will be effective
only on sources with LFE channel.
The value from "80Hz" to "120Hz (Default Value)" can be set.
"Off": Do not use this function
Double Bass
This can be selected only when "Configuration" - "Subwoofer" is
set to "Yes" and "Front" is set to "Full Band".
Boost bass output by feeding bass sounds from the front left and
right, and center speakers to the subwoofer.
"On": Bass output will be boosted
"Off": Bass output will not be boosted
0 The setting will not automatically be configured even if you
performed AccuEQ Room Calibration.
■ 3. Distance
Set the distance from each speaker to the listening position.
Front Left
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
Center
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
Front Right
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
Height Left
Specify the distance between each speaker and the listening
position. (Default Value is "9.0ft/2.70m")
Height Right
Specify the distance between each speaker and the listening
position. (Default Value is "9.0ft/2.70m")
Surround Right
Specify the distance between each speaker and the listening
position. (Default Value is "7.0ft/2.10m")
Surround Left
Specify the distance between each speaker and the listening
position. (Default Value is "7.0ft/2.10m")
Subwoofer
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
0 Default values vary depending on the regions.
0 Distance units can be switched by pressing Mode on the remote controller. When the unit
is set as feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1 ft. When the unit
is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.
57
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
■ 4. Level Calibration
Front Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Center
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Front Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Height Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Height Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Surround Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Surround Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Subwoofer
Select a value between "j15 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
∫ 5. Dolby Enabled Speaker
Dolby Enabled
Speaker to Ceiling
58
Set the distance between the Dolby enabled speaker and the
ceiling. Select a value between "0.1 ft/0.03 m" and "15.0 ft/
4.50 m" (in 0.1 ft/0.03 m increments, default value is "6.0 ft")
0 The unit of distance (feet/meters) shown is the unit selected
for use in "Distance".
AccuReflex
You can enhance the reflection effect of Dolby enabled speaker
from the ceiling.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
0 The function is not effective if the listening mode is Direct.
0 This setting can only be selected when you have set "Configuration" - "Height Speaker" to
"Dolby Speaker".
■ 6. Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to 5 bands for the Subwoofer and 15
bands for all other speakers. To use the set equalizer effects, select the preset number in
"Quick Menu"- "AccuEQ" - "Equalizer" (P50).
Front
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors /, adjust the volume of that
frequency between "j6.0 dB" and "i6.0 dB" with /. (Default
Value is "0.0 dB")
Center
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors /, adjust the volume of that
frequency between "j6.0 dB" and "i6.0 dB" with /. (Default
Value is "0.0 dB")
Height
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors /, adjust the volume of that
frequency between "j6.0 dB" and "i6.0 dB" with /. (Default
Value is "0.0 dB")
Surround
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors /, adjust the volume of that
frequency between "j6.0 dB" and "i6.0 dB" with /. (Default
Value is "0.0 dB")
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Subwoofer
After selecting the speaker frequency from between "25 Hz" and
"160 Hz" with the cursors /, adjust the volume of that
frequency between "j6.0 dB" and "i6.0 dB" with /. (Default
Value is "0.0 dB")
0 This cannot be selected if "No" is set in "Configuration" "Subwoofer".
3. Audio Adjust
■ 1. Multiplex/Mono
Multiplex Input
Channel
Set the audio channel or language to be output when playing
multiplex audio or multilingual TV broadcasts etc.
"Main (Default Value)": Main channel only
"Sub": Sub channel only
"Main / Sub": Main and sub channels will be output at the same
time.
0 If multiplex audio is being played, "1+1" will be displayed on
the display of this unit when
on the remote controller is
pressed.
Mono Input Channel
Set the input channel to use for playing any 2 ch digital source
such as Dolby Digital, or 2 ch analog/PCM source in the Mono
listening mode.
"Left": Left channel only
"Right": Right channel only
"Left + Right (Default Value)": Left and right channels
0 The result may not be as expected depending on the input source and listening mode
setting.
■ 2. Dolby
Loudness
Management
When playing Dolby TrueHD, enable the dialog normalization
function which keeps the volume of dialog at a certain level. Note
that when this setting is Off, the Late Night function that allows
you to enjoy surround at low volumes is fixed to off when playing
Dolby Digital Plus/Dolby TrueHD.
"On (Default Value)": Use this function
"Off": Do not use this function
59
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
■ 3. DTS
4. Source
0 We plan to provide support for the DTS:X audio format through firmware updates for this
unit. This setting will become possible after updating.
■ 1. IntelliVolume
DTS Auto Surround
When inputting DTS signals that include extended channel
information, the optimum listening mode is automatically
selected according to the extended information contained in the
input signal and the speaker configuration of this unit when
playing in the straight decoding listening mode.
"On (Default Value)": Use this function
"Off": Audio is played using the same amount of channels in the
input signal according to the speaker configuration of this unit.
IntelliVolume
Select a value between "j12 dB" and "i12 dB". Set a negative
value if the volume of the target device is larger than the others
and a positive value if smaller. To check the audio, start playback
of the connected device. (Default Value is "0 dB")
■ 2. Name Edit
Set an easy name to each input. The set name will be shown on the main unit display. Select
the input selector to configure.
■ 4. LFE Level
Set the low-frequency effect (LFE) level for Dolby Digital series, DTS series, Multichannel
PCM, and DSD signals.
LFE Level
Adjust the volume level difference between the devices connected to the unit. Select the
input selector to configure.
Select the low-frequency effect (LFE) level of each type of signal
from "0 dB (Default Value)" to "j ∞ dB". If the low-frequency
effect sound is too strong, select "j20dB" or "j ∞ dB".
■ 5. Volume
Maximum Volume
Set the maximum value to avoid too high volume. Select "Off
(Default Value)" or a value between "30" and "49".
Headphone Level
Adjust the output level of the headphones. Select a value between
"j12 dB" and "i12 dB". (Default Value is "0 dB")
Name Edit
1. Select a character or symbol with the cursors and press Enter.
Repeat it to input 10 or less characters.
"A/a": Switches between upper and lower cases. (Pressing
Mode on the remote controller also toggles between upper
and lower cases)
" ← " " → ": Moves the cursor to the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
0 Pressing Clear on the remote controller will remove all the
input characters.
2. After inputting, select "OK" with the cursors and press Enter.
The input name will be saved.
0 To name a preset radio station, press Tuner on the remote controller, select FM and select
the preset number.
0 This cannot be set if the "NET","USB" or "BLUETOOTH" input is selected.
60
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
■ Audio Select
Select the priority for input selection when multiple audio sources are connected to one input
selector, such as connections to both the "BD/DVD" HDMI IN jack and the "BD/DVD" AUDIO
IN jack. The setting can be separately set to each input selector button. Select the input
selector to configure. Note that there are some default values you cannot change.
Audio Select
"ARC": When giving priority to input signal from ARC compatible TV.
0 The setting can be selected only when "5. Hardware" - "HDMI"
- "Audio Return Channel" is set to "Auto" and also the "TV"
input is selected.
"HDMI": When giving priority to input signal from HDMI IN jacks
0 The setting can be selected only when the input is assigned to
the HDMI jack in the "1. Input/Output Assign" - "HDMI Input"
setting.
"COAXIAL": When giving priority to input signal from DIGITAL IN
COAXIAL jacks
0 The setting can be selected only when the input is assigned to
the COAXIAL jack in the "1. Input/Output Assign" - "Digital
Audio Input" setting.
"OPTICAL": When giving priority to input signal from DIGITAL IN
OPTICAL jacks
0 The setting can be selected only when the input is assigned to
the OPTICAL jack in the "1. Input/Output Assign" - "Digital
Audio Input".
"Analog": To always output analog audio independently of the
input signal
0 The setting can be selected only when the input is assigned to
the AUDIO IN jack in the "1. Input/Output Assign" - "Analog
Audio Input" setting.
(Default Value: BD/DVD: HDMI, CBL/SAT: HDMI, GAME: HDMI,
STRM BOX: HDMI, CD: COAXIAL, TV: OPTICAL, PHONO:
Analog)
PCM Fixed Mode
Select whether to fix input signals to PCM (except multi-channel
PCM) when you have selected "HDMI", "COAXIAL", or
"OPTICAL" in the "Audio Select" setting. Set this item to "On" if
noise is produced or truncation occurs at the beginning of a track
when playing PCM sources. Select "Off (Default Value)"
normally.
0 Changing "Audio Select" changes the setting to "Off".
0 The setting cannot be changed when "TUNER", "NET", "USB" or "BLUETOOTH" input is
selected.
■ Video Select
When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the input from
which video is displayed on the TV.
Video Select
"Last (Default Value)": Select the video input played immediately
prior.
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "CD", "TV",
"PHONO": Play the video from the selected input.
0 This setting is effective for an input selector which is assigned
in "1. Input/Output Assign" - "HDMI Input".
0 If the OSD language is set to Chinese, you can only select this setting when "TUNER" is
selected as input.
61
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
5. Hardware
HDMI Standby
Through
■ 1. HDMI
HDMI CEC
62
Setting to "On" enables the input selection link and other link
functions with HDMI connected CEC compliant device.
"On": Use this function
"Off (Default Value)": Do not use this function
When changing this setting, turn off and then on again the power
of all connected components.
0 Depending on the TV set, a link may need to be configured on
the TV.
0 Setting to "On" and closing the on-screen menu displays the
name of the CEC-compatible components and "CEC On" on
the display of this unit.
0 Power consumption in standby mode may increase if "On" is
set. (Depending on the TV status, the unit will enter the
normal standby mode.)
0 If you operate the volume dial on the unit when this setting is
"On" and audio is output from the TV speakers, audio will be
output also from the speakers connected to the unit. If you
want to output from only either of them, change the unit or TV
settings, or reduce the volume of the unit.
0 If abnormal operation occurs when you set the setting to "On",
set it to "Off".
0 When connecting a non-CEC compatible component, or when
you are not sure whether it is compatible, set the setting to
"Off".
When this is set to anything other than "Off", you can play the
video and audio of an HDMI connected player on the TV even if
the unit is in standby mode. Only "Auto" and "Auto (Eco)" can be
selected if "HDMI CEC" is set to "On". If you select anything
else, set "HDMI CEC" to "Off". (Default Value is “Off”)
0 Power consumption in standby mode increases if set to
anything other than "Off".
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "CD", "TV",
"PHONO": For example, if you select "BD/DVD", you can play
the equipment connected to the "BD/DVD" jack on the TV even if
the unit is in standby mode. Select this setting if you have
decided which player to use with this function.
"Last": You can play the video and audio of the input selected
immediately prior to the unit being switched to standby on the
TV.
"Auto", "Auto (Eco)": Select one of these settings when you have
connected equipment that conforms to the CEC standard. You
can play the video and audio of the input selected on the TV,
irrespective of what input was selected immediately prior to the
unit being switched to standby, using the CEC link function.
0 To play players on the TV that do not conform to the CEC
standard, you will need to turn the unit on and switch to the
relevant input.
0 When using TV that complies with the CEC standard, you can
reduce the power consumption in standby mode by selecting
"Auto (Eco)".
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Audio TV Out
Audio Return Channel
Auto Lip Sync
You can enjoy audio through the speakers of the TV while this
unit is on.
"On": Use this function
"Off (Default Value)": Do not use this function
0 The setting is fixed to "Auto" if "HDMI CEC" is set to "On". If
you change this setting, set "HDMI CEC" to "Off."
0 Listening mode cannot be changed while "Audio TV Out" is
set to "On" and audio is being output through the speakers of
the TV.
0 Depending on your TV set or input signal of the component,
audio may not output through the speakers of the TV even if
this setting is set to "On". In such case, audio is output from
the speakers of the unit.
0 If you operate the volume dial on this unit when audio that is
being input through this unit for output from the TV speakers,
audio is output from this unit. If you do not want to output
audio from the unit, change the unit or TV settings, or reduce
the volume of the unit.
■ 2. Network
0 When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting
automatically. To assign fixed IP addresses to each component, you must set "DHCP" to
"Disable" and assign an address to this unit in "IP Address" as well as set information
related to your LAN, such as Subnet Mask and Gateway.
Wi-Fi
Connect the unit to network via wireless LAN router.
"On": Wireless LAN connection
"Off (Wired) (Default Value)": Wired LAN connection
Wi-Fi Setup
You can configure wireless LAN settings by pressing Enter when
"Start" is displayed.
0 Refer to "3. Network Connection" (P20) in Initial Setup for
details.
Wi-Fi Status
The information of the connected access point will be displayed.
"SSID": SSID of the connected access point.
"Signal": Signal strength of the connected access point.
"Status": Status of the connected access point.
You can enjoy sound of the HDMI connected ARC compatible
TV through the speakers connected to the unit.
To use this function, set "HDMI CEC" to "On" in advance.
"Auto": When enjoying the TV sound through the speakers
connected to the unit
"Off": When not using the ARC function
MAC Address
This is the MAC address of this unit.
This value is specific to the component and cannot be changed.
DHCP
"Enable (Default Value)": Auto configuration by DHCP
"Disable": Manual configuration without DHCP
If selecting "Disable", you must set "IP Address", "Subnet Mask",
"Gateway", and "DNS Server" manually.
This setting automatically corrects any desynchronization
between the video and audio signals based on data from the
HDMI LipSync compatible TV.
"On (Default Value)": Automatic correction will be enabled.
"Off": Automatic correction will be disabled.
IP Address
Displays/Sets the IP address.
Subnet Mask
Displays/Sets the subnet mask.
Gateway
Displays/Sets the gateway.
DNS Server
Displays/Sets the primary DNS server.
Proxy URL
Displays/Sets the proxy server URL.
Proxy Port
Displays/Sets the proxy server port number when you enter
"Proxy URL".
63
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Friendly Name
AirPlay Password
64
Change the device name for this unit which is shown on other
devices connected to the network to an easily recognized name.
This is set to Integra DSX-3 ****** at the time of
purchase. (" * " stand for alphanumeric characters identifying
each unit)
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors and press Enter.
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing
Mode on the remote controller also toggles between upper
and lower cases.)
" ← " " → ": Moves the cursor to the arrow direction.
"
": Removes a character on the left of the cursor.
" ": Enters a space.
0 Pressing Clear on the remote controller will remove all the
input characters.
3. After inputting, select "OK" with the cursors and press Enter.
The input name will be saved.
You can set a password of up to 31 characters so that only
registered users can use AirPlay.
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors and press Enter.
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing
Mode on the remote controller also toggles between upper
and lower cases.)
" ← " " → ": Moves the cursor to the arrow direction.
"
": Removes a character on the left of the cursor.
" ": Enters a space.
0 To select whether to mask the password with " * " or display it
in plain text, press Memory on the remote controller.
0 Pressing Clear on the remote controller will remove all the
input characters.
3. After inputting, select "OK" with the cursors and press Enter.
The input password will be saved.
Usage Data
As a means of improving the quality of our products and
services, our company may collect information about your usage
over the network. Select "Yes" if you agree to our collecting this
information. Select "No" if you do not want us to collect this
information. (Default Value is "No")
You can set this after confirming the Privacy Policy. When you
select "Usage Data" and press Enter, the Privacy Policy is
displayed. (The same screen is displayed once also when
setting up the network connection.) If you agree to the collection
of the information, this setting also becomes "Yes". Note that if
you agree to the Privacy Policy but select "No" for this setting,
the information will not be collected.
Network Check
You can check the network connection.
Press Enter when "Start" is displayed.
0 Wait for a while if "Network" cannot be selected. It will appear when the network feature is
started.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
■ 3. Bluetooth
Status
Bluetooth
Select whether or not to use the BLUETOOTH function.
"On (Default Value)": Enables connection with a BLUETOOTH
enabled device by using the BLUETOOTH function. Select "On"
also when making various BLUETOOTH settings.
"Off": When not using the BLUETOOTH function
Auto Input Change
The input of the unit will automatically be switched to
"BLUETOOTH" when connection is made from a BLUETOOTH
enabled device to the unit.
"On (Default Value)": The input will automatically become
"BLUETOOTH" when a BLUETOOTH enabled device is connected.
"Off": The function is disabled.
0 If the input is not switched automatically, set to "Off" and
change the input manually.
Auto Reconnect
This function automatically reconnects to the BLUETOOTH
enabled device connected last when you change the input to
"BLUETOOTH".
"On (Default Value)": Use this function
"Off": Do not use this function
0 This may not work with some BLUETOOTH enabled devices.
Pairing Information
You can initialize the pairing information saved on this unit.
Pressing Enter when "Clear" is displayed initializes the pairing
information stored in this unit.
0 This function does not initialize the pairing information on the
BLUETOOTH enabled device. When pairing the unit again
with the device, be sure to clear the pairing information on the
BLUETOOTH enabled device in advance. For information on
how to clear the pairing information, refer to the BLUETOOTH
enabled device's instruction manual.
Device
Displays the name of the BLUETOOTH enabled device
connected to the unit.
0 The name is not displayed when "Status" is "Ready" and
"Pairing".
Displays the status of the BLUETOOTH enabled device
connected to the unit.
"Ready": Not paired
"Pairing": Paired
"Connected": Successfully connected
0 Wait for a while if "Bluetooth" cannot be selected. It will appear when the BLUETOOTH
function is started up.
■ 4. Power Management
Sleep Timer
Allows the unit to enter standby automatically when the specified
time elapses. Select from "30 minutes", "60 minutes", and "90
minutes".
"Off (Default Value)": Does not turn the unit to standby
automatically.
Auto Standby
This setting places the unit on standby automatically after 20
minutes of inactivity without any video or audio input.
(When "USB Power Out at Standby" or "Network Standby" is on,
this becomes the HYBRID STANDBY mode which reduces the
increase in power consumption to a minimum.)
"On": The unit will automatically enter standby mode ("ASb" will
stay lit).
"Off (Default Value)": The unit will not automatically enter
standby mode.
0 "Auto Standby" is displayed on the display of this unit and TV
screen 30 seconds before the Auto Standby comes on.
Auto Standby in HDMI
Standby Through
Enable or disable "Auto Standby" while "HDMI Standby Through"
is on.
"On": The setting will be enabled.
"Off": The setting will be disabled.
0 This setting cannot be set to "On" if "Auto Standby" is set to
"Off".
65
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
USB Power Out at
Standby
Network Standby
Bluetooth Wakeup
Devices connected to the USB port are supplied with electricity
even when this unit is in standby mode when this function is
"On". (Default Value is "Off")
0 When using this feature, power consumption increases even
when the unit is on standby, however, the increase in power
consumption is kept to a minimum by automatically entering
the HYBRID STANDBY mode, where only essential circuits
are operating.
When this feature is turned "On (Default Value)", you can turn on
the power of the unit via the network using an application that
can control this unit.
0 When "Network Standby" is used, the power consumption
increases even when the unit is on standby. However, the
increase in power consumption is kept to a minimum by
automatically entering the HYBRID STANDBY mode, where
only the essential circuit is operating.
0 "Network Standby", which suppresses power consumption,
may be disabled when the network connection is lost. Use the
power button on the remote controller or this unit to turn the
unit on if this happens.
This function wakes up the unit on standby by connecting a
BLUETOOTH enabled device.
"On": Use this function
"Off (Default Value)": Do not use this function
0 Setting to "On" increases the power consumption even when
the unit is on standby. However, the increase in power
consumption is kept to a minimum by automatically entering
the HYBRID STANDBY mode, where only the essential circuit
is operating.
0 This setting is fixed to "Off" if "5. Hardware" - "Bluetooth" "Auto Input Change" is set to "Off".
0 Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It will
appear when the network feature is started.
66
6. Miscellaneous
■ 1. Tuner
FM Frequency Step
Select a frequency step depending on your area of residence.
Select "0.2 MHz (Default Value)" or "0.05 MHz".
0 When this setting is changed, all radio presets are deleted.
■ 2. Firmware Update
Update Notice
Availability of a firmware update will be notified via network.
"Enable (Default Value)": Notify updates
"Disable": Do not notify updates
Version
The current firmware version will be displayed.
Update via NET
Press Enter to select when you want to update the firmware via
network.
0 You will not be able to select this setting if you do not have
Internet access or there is nothing to update.
Update via USB
Press Enter to select when you want to update the firmware via
USB.
0 You will not be able to select this setting if a USB storage
device is not connected or there is nothing to update in the
USB storage device.
0 Wait for a while if "Firmware Update" cannot be selected. It will appear when the network
feature is started.
■ 3. Initial Setup
You can make the Initial Setup from the Setup menu.
0 Wait for a while if "Initial Setup" cannot be selected. It will appear when the network
feature is started.
■ 4. Lock
Setup Parameter
Lock the Setup menu to protect the settings.
"Locked": The menu is locked.
"Unlocked (Default Value)": The menu is unlocked.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
■ 5. Load Default
Load Default
Reset the unit to return the settings to the status at the time of
shipment. Reset is complete when "Clear" is displayed on the
display and the unit switches to standby.
Your settings will also be initialized when you reset, so note
down your settings before starting reset.
67
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Control Function Settings
You can enable the control functions between the unit and
external devices. Special devices or cable connections are
necessary to enable the functions. For more information
about installation, contact a store specializing in these
products.
IR jack
If you use a commercially available multiroom remote
control kit with this jack, you can operate the unit with the
remote controller even when you are in a separate room, or
operate the unit with the remote controller even if its remote
control sensor is difficult to see.
This unit
Connecting
block
IR receiver
Remote
controller
Main room
Separate room
Signal flow
0 Other companies may use indications other than IR on
their products. Confirm in the instruction manual included
with your components.
0 Refer to the instruction manual of the IR receiver for the
types of cables required for connection.
68
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Firmware Update
Firmware Update
Update function of this unit
How to update firmware
Updating the Firmware via Network
This unit has functionality to update the firmware (the
system software) over a network or by the USB port. This
enables us to make improvements to a variety of operations
and to add features.
There are two methods for updating the firmware: via
network and via USB. The update may take about 20
minutes to complete for either method: via network or via
USB. Furthermore, existing settings are guaranteed
regardless of the method used for update.
Note that when this unit is connected to a network, you may
see notifications about firmware updates on the display. To
execute updating, select "Update" with the cursor buttons of
the remote controller and press Enter. "Completed!" is
displayed when the update is complete.
0 For the latest information on updates, visit our company’s
website. There is no need to update the firmware on this
unit if there is no update available.
0 Before updating, make sure that the speaker setup
microphone is not connected.
0 During an update, do not
– Disconnect and reconnect any cable, USB storage
device, speaker setup microphone or headphones, or
perform any operation on the component such as turn
off its power
– Accessing this unit from a PC or smartphone using an
application
0 Check that the unit is turned on, and the connection to
the Internet is secured.
0 Turn off the controller component (PC etc.) connected to
the network.
0 Stop any playing Internet radio, USB storage device, or
server content.
0 When "5. Hardware" - "HDMI" - "HDMI CEC" in the
System Setup menu is set to "On", set it to "Off".
0 The description may differ from the on-screen display but
that will not change the way to operate or the function.
1. Switch the input on the TV to that assigned to the unit.
2. Press
on the remote controller.
Disclaimer: The program and accompanying online
documentation are furnished to you for use at your own risk.
We will not be liable and you will have no remedy for damages
for any claim of any kind whatsoever concerning your use of the
program or the accompanying online documentation, regardless
of legal theory, and whether arising in tort or contract.
In no event will we be liable to you or any third party for any
special, indirect, incidental, or consequential damages of
any kind, including, but not limited to, compensation,
reimbursement or damages on account of the loss of
present or prospective profits, loss of data, or for any other
reason whatsoever.
Setup
1. Input/Output Assign
1. TV Out / OSD
2. Speaker
2. HDMI Input
3. Audio Adjust
3. Digital Audio Input
4. Source
4. Analog Audio Input
5. Hardware
6. Miscellaneous
3. Select "6. Miscellaneous" - "Firmware Update" - "Update
via NET" with the cursors in order, then press Enter.
Setup
1. Input/Output Assign
1. Tuner
2. Speaker
2. Firmware Update
3. Audio Adjust
3. Initial Setup
4. Source
4. Lock
5. Hardware
5. Load Default
6. Miscellaneous
0 If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0 You will not be able to select "Update via NET" if there is
nothing to update.
69
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
4. Press Enter with "Update" selected to start update.
0 During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of this unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0 "Completed!" is displayed when the update is
complete.
5. Press Í On/Standby on this unit to turn the unit into
standby mode. The process is completed and your
firmware is updated to the latest version.
0 Do not use Í on the remote controller.
If an error message is displayed: When an error occurs,
"*-** Error!" is displayed on the display of this unit. ("*"
represents an alphanumeric character.) Check the
following:
0 * -01, * -10: Ethernet cable not found. Connect the
Ethernet cable properly.
0 *-02, *-03, *-04, *-05, *-06, *-11, *-13, *-14, *
-16, * -17, * -18, * -20, * -21: Internet connection
error. Check the following:
– The router is turned on
– This unit and the router are connected via the network
Try to disconnect and then connect again the power to
the unit and router. This may solve the problem. If you
are still unable to connect to the Internet, the DNS server
or proxy server may be temporarily down. Check the
service status with your ISP provider.
0 Others: Disconnect then reconnect the AC power cord,
then repeat from the beginning.
0
0
0
0
0
0
0
1.
2.
3.
4.
Updating via USB
0 Prepare a 128 MB or larger USB storage device. FAT16
or FAT32 file system format.
– Media inserted in a USB card reader may not be used
for this function.
– USB storage devices with security function are not
70
5.
6.
supported.
– USB hubs and USB devices with hub function are not
supported. Do not connect these devices to the unit.
Delete any data stored on the USB storage device.
Turn off the controller component (PC etc.) connected to
the network.
Stop any playing Internet radio, USB storage device, or
server content.
When "5. Hardware" - "HDMI" - "HDMI CEC" in the Setup
menu is set to "On", set it to "Off".
Some USB storage devices may take long to load, may
not be loaded correctly, or may not be correctly fed
depending on the device or their content.
We will not be liable whatsoever for any loss or damage
of data, or storage failure arising from the use of the USB
storage device with this unit. Thank you for your
understanding.
The description may differ from the on-screen display but
that will not change the way to operate or the function.
Connect the USB storage device to your PC.
Download the firmware file from our company’s website
to your PC and unzip.
Firmware files are named in the following way:
ONKSLM0001_S50000SASASOSO_ *** .zip
Unzip the file on your PC. The number of unzipped files
and folders varies depending on the model.
Copy all unzipped files and folders to the root folder of
the USB storage device.
0 Make sure to copy the unzipped files.
Connect the USB storage device to the USB port of this
unit.
0 If you connect a USB hard disk drive to the USB port of
the unit, we recommend that you use its AC adapter to
power it.
0 If the USB storage device has been partitioned, each
section will be treated as an independent device.
Switch the input on the TV to that assigned to the unit.
Press
on the remote controller.
Setup
1. Input/Output Assign
1. TV Out / OSD
2. Speaker
2. HDMI Input
3. Audio Adjust
3. Digital Audio Input
4. Source
4. Analog Audio Input
5. Hardware
6. Miscellaneous
7. Select "6. Miscellaneous" - "Firmware Update" - "Update
via USB" with the cursors in order, then press Enter.
Setup
1. Input/Output Assign
1. Tuner
2. Speaker
2. Firmware Update
3. Audio Adjust
3. Initial Setup
4. Source
4. Lock
5. Hardware
5. Load Default
6. Miscellaneous
0 If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0 You will not be able to select "Update via USB" if there
is nothing to update.
8. Press Enter with "Update" selected to start update.
0 During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of this unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0 During the update, do not turn off, or disconnect then
reconnect the USB storage device.
0 "Completed!" is displayed when the update is
complete.
9. Remove the USB storage device from this unit.
10.Press Í On/Standby on this unit to turn the unit into
standby mode. The process is completed and your
firmware is updated to the latest version.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
0 Do not use Í on the remote controller.
If an error message is displayed: When an error occurs,
"*-** Error!" is displayed on the display of this unit. ("*"
represents an alphanumeric character.) Check the
following:
0 * -01, * -10: USB storage device not found. Check
whether the USB storage device or USB cable is
correctly inserted to the USB port of this unit.
Connect the USB storage device to an external power
source if it has its own power supply.
0 * -05, * -13, * -20, * -21: The firmware file is not
present in the root folder of the USB storage device, or
the firmware file is for another model. Retry from the
download of the firmware file.
0 Others: Disconnect then reconnect the AC power cord,
then repeat from the beginning.
71
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Troubleshooting
Others
Before starting the procedure
Problems may be solved by simply turning the power on/off
or disconnecting/connecting the power cord, which is easier
than working on the connection, setting and operating
procedure. Try the simple measures on both the unit and
the connected device. If the problem is that the video or
audio is not output or the HDMI linked operation does not
work, disconnecting/connecting the HDMI cable may solve
it. When reconnecting, be careful not to wind the HDMI
cable since if wound the HDMI cable may not fit well. After
reconnecting, turn off and on the unit and the connected
device.
0 This unit contains a microPC for signal processing and
control functions. In very rare situations, severe
interference, noise from an external source, or static
electricity may cause it to lockup. In the unlikely event
that this happens, unplug the power cord from the wall
outlet, wait at least 5 seconds, and then plug it back in.
0 We are not responsible for reparations for damages
(such as CD rental fees) due to unsuccessful recordings
caused by the unit’s malfunction. Before you record
important data, make sure that the material will be
recorded correctly.
If operation becomes unstable
Try restarting the unit
The issue may be fixed by restarting this unit. After
switching this unit to standby, press and hold Í On/Standby
on this unit for 5 or more seconds to restart the unit. (The
settings in the unit are maintained.) If restarting the unit
doesn't fix the problem, try to disconnect and then connect
again the power to the unit and other connected
components.
Resetting the unit (this resets the unit settings to the
default)
If restarting the unit doesn't fix the problem, resetting the unit
72
to the status at the time of shipment may solve the problem.
Your settings will also be initialized when you reset, so note
down your settings before doing the following.
1. Press
on the remote controller, select "6.
Miscellaneous" - "Load Default" in the Setup screen and
press Enter.
2. Select "Yes", and then press Enter.
3. The unit switches to standby and the settings are reset.
■ Power
Cannot turn on the unit
0 Make sure that the power cord is properly plugged into
the wall outlet.
0 Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
The unit turns off unexpectedly
0 The unit automatically switches to standby when the "5.
Hardware" - "Power Management" - "Auto Standby"
setting in the Setup menu functions.
0 If "CHECK SP WIRE" appears on the display, the
speaker cables may be short-circuited. Make sure bare
speaker wires are not touching each other or the back
panel of the unit, then turn the unit on again.
0 The protective circuit function may have been activated
because the temperature of the unit rose abnormally. If
this happens, then the power will continue to turn off after
you have turned the unit on again. Make sure the unit has
plenty of space for ventilation around it, wait for the unit
to cool down sufficiently, and then try turning it on again.
WARNING: If smoke, smell or abnormal noise is produced
by the unit, unplug the power cord from the wall outlet
immediately and contact the dealer or our company’s
support.
■ Audio
0 Make sure that the speaker setup microphone is not still
connected.
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 If the MUTING indicator on the display flashes, press
on the remote controller to cancel muting.
0 While headphones are connected to the Phones jack, no
sound is output from the speakers.
0 When "4. Source" - "Audio Select" - "PCM Fixed Mode" in
the Setup menu is set to "On", no sound is played when
signals other than PCM are input. Change the setting to
Off.
Check the following if the above does not fix the problem:
There is no sound from the TV
0 Change the input selector on this unit to the position of
the terminal to which the TV is connected.
0 If the TV doesn't support the ARC function, along with
connection by HDMI, connect the TV and this unit using a
digital optical cable, digital coaxial cable or analog audio
cable.
No sound from a connected player
0 Change the input selector on this unit to the position of
the terminal to which the player is connected.
0 Check the digital audio output setting on the connected
component. On some game consoles, such as those that
support DVD, the default setting is OFF.
0 With some DVD-Video discs, you need to select an audio
output format from a menu.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
A speaker produces no sound
0 Make sure that the polarity of the speaker cables ( + / − )
is correct, and that no bare wires are in contact with the
metal part of speaker terminals.
0 Make sure that the speaker cables are not shorting.
0 Check that the speaker connections have been made
correctly. (P12) Settings for the speaker connection
environment need to be made in "1. AccuEQ Room
Calibration" in Initial Setup. (P19)
0 Depending on the source and current listening mode, not
much sound may be produced by the surround speakers.
Select another listening mode to see if sound is output.
The subwoofer produces no sound
0 When you play source material that contains no
information in the LFE channel, the subwoofer produces
no sound.
Noise can be heard
0 Using cable ties to bundle RCA cables with power cords,
speaker cable, etc. may degrade the audio performance,
so refrain from doing it.
0 An audio cable may be picking up interference. Try
repositioning your cables.
The beginning of audio received via HDMI cannot be
heard
0 Since it takes longer to identify the format of an HDMI
signal than it does for other digital audio signals, audio
output may not start immediately.
Sound suddenly reduces
0 When the temperature inside the unit exceeds a certain
temperature for extended periods, the volume may be
reduced automatically to protect the circuits.
■ Listening Modes
0 To enjoy digital surround playback, such as Dolby Digital,
the audio signals need to pass through a connection via
HDMI cable, digital coaxial cable or digital optical cable.
Audio output should be set to bitstream output on the
connected Blu-ray Disc player or other device.
0 Press
on the remote controller several times to switch
the display of this unit to check the input format.
Check the following if the above does not fix the problem:
Cannot select a desired listening mode
0 Depending on the connecting status of the speaker,
some listening modes may not be selected. (P35)
There is no sound with Dolby TrueHD, Dolby Atmos,
DTS-HD Master Audio and DTS:X.
0 If you cannot output formats such as Dolby TrueHD,
Dolby Atmos, DTS-HD Master Audio or DTS:X according
to the format of the source, in the Blu-ray Disc player
settings try setting "BD video supplementary sound" (or
re-encode, secondary sound, video additional audio,
etc.) to "Off". Change the listening mode for each source
after changing the setting to confirm.
0 We plan to provide support for the Dolby Atmos and
DTS:X audio format through firmware updates for this
unit.
About DTS signals
0 With media that switches suddenly from DTS to PCM,
PCM playback may not start immediately. In such cases,
you should stop your player for about 3 seconds and then
resume playback.
0 With some CD and LD players, you will not be able to
playback DTS material properly even though your player
is connected to a digital input on the unit. This is usually
because the DTS bitstream has been processed (e.g.,
output level, sampling rate, or frequency response
changed) and the unit does not recognize it as a genuine
DTS signal. In such cases, you may hear noise.
0 Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
■ Video
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 When the TV image is blurry or unclear, power code or
connection cables of the unit may have interfered. In that
case, keep distance between TV antenna cable and
cables of the unit.
0 Make sure the switching of input screens is proper at the
monitor side such as a TV.
Check the following if the above does not fix the problem:
There is no video
0 Change the input selector on this unit to the position of
the terminal to which the player is connected.
There is no picture from a source connected to an HDMI
IN terminal
0 To display video from the connected player on the TV
while the unit is in standby, you need to enable "5.
Hardware" - "HDMI" - "HDMI Standby Through" in the
Setup menu. Refer to (P62) for information about
HDMI Standby Through.
0 Check if "Resolution Error" is displayed on this unit's
display when video input via HDMI IN jack is not
displayed. In this case, the TV does not support the
resolution of the video input from the player. Change the
setting on the player.
0 Reliable operation with an HDMI-to-DVI adapter is not
guaranteed. In addition, video signals from a PC are not
supported.
73
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Images flicker
0 It is possible that the resolution of the player is not
compatible with the TV's resolution. If you have
connected the player to this unit with an HDMI cable, try
changing the output resolution on the player. There also
may be an improvement if you change the screen mode
on the TV.
Video and audio are out of sync
0 Video may be delayed relative to audio depending on the
settings and connections with your television. To adjust,
press Q on the remote controller, and adjust in "Other" "A/V Sync" in "Quick Menu".
0 Try plugging/unplugging the power of the unit and try
turning on/off the BLUETOOTH enabled device. Restarting
the BLUETOOTH enabled device may be effective.
0 The BLUETOOTH enabled devices must support the
A2DP profile.
0 Near components such as microwave oven or cordless
phone, which use the radio wave in the 2.4 GHz range, a
radio wave interference may occur, which disables the
use of this unit.
0 If there is a metallic object near the unit, BLUETOOTH
connection may not be possible as the metal can effect
on the radio waves.
■ Linked operation
Check the following if the above does not fix the problem:
There is no linked operation with CEC compliant
devices, such as a TV
0 In the Setup menu of the unit, set "5. Hardware" - "HDMI"
- "HDMI CEC" to "On".
0 It is also necessary to set HDMI linking on the CEC
compliant device. Check the instruction manual.
Cannot connect with this unit
0 Check that the BLUETOOTH function of the
BLUETOOTH enabled device is enabled.
■ FM broadcasts
Radio reception is poor or there is a lot of noise.
0 Re-check the antenna connection.
0 Move the antenna away from the speaker cable or the
power cord.
0 Move the unit away from your TV or PC.
0 Passing cars and airplanes can cause interference.
0 Concrete walls weaken radio signals.
0 Listen to the station in mono.
0 FM reception may become clearer if you use the antenna
jack on the wall used for the TV.
74
■ BLUETOOTH function
Music playback is unavailable on the unit even after
successful BLUETOOTH connection
0 When the audio volume of your BLUETOOTH enabled
device is set low, the playback of audio may be unavailable.
Turn up the volume on the BLUETOOTH enabled device.
0 Some BLUETOOTH enabled devices may be equipped
with a Send/Receive selector switch. Select Send mode.
0 Depending on the characteristics or specifications of your
BLUETOOTH enabled device, playback on this unit may
not be possible.
Sound is interrupted
0 There may be a problem with the BLUETOOTH enabled
device. Check the information on the internet.
The audio quality is poor after connection with a
BLUETOOTH enabled device
0 The BLUETOOTH reception is poor. Move the BLUETOOTH
enabled device closer to the unit or remove any obstacle
between the BLUETOOTH enabled device and this unit.
■ Network function
0 If you cannot select a network service, it will become
selectable when the network function is started. It may
take about a minute to start up.
0 When NET is blinking, this unit is not properly connected
to the home network.
0 Try plugging/unplugging the power supply of this unit and
the router, and try rebooting the router.
0 If the desired wireless LAN router is not in the access
point list, it may be set to hide SSID or the ANY
connection may be off. Change the setting and try again.
Check the following if the above does not fix the problem:
Cannot access the Internet radio
0 Certain network service or contents available through the
unit may not be accessible in case the service provider
terminates its service.
0 Make sure that your modem and router are properly
connected, and make sure they are both turned on.
0 Make sure that the LAN side port on the router is properly
connected to this unit.
0 Make sure that connecting to Internet from other
components is possible. If connecting is not possible,
turn off all components connected to the network, wait for
a while, and then turn on the components again.
0 If a specific radio station is unavailable for listening, make
sure the registered URL is correct, or whether the format
distributed from the radio station is supported by this unit.
0 Depending on ISP, setting the proxy server is necessary.
0 Make sure that the used router and/or modem is
supported by your ISP.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Cannot access the network server
0 This unit needs to be connected to the same router as
the network server.
0 This unit is compatible with Windows Media® Player 11 or
12 network servers or NAS that are compatible with
home network functionality.
0 You may need to make some settings on Windows
Media® Player. (P25)
0 When using a PC, only music files registered in the
Windows Media® Player library can be played.
Playback stops while listening to music files on the
network server
0 Make sure the network server is compatible with this unit.
0 When the PC is serving as the network server, try quitting
any application software other than the server software
(Windows Media® Player 12, etc.).
0 If the PC is downloading or copying large files, the
playback may be interrupted.
■ USB storage device
USB storage device is not displayed
0 Check whether the USB storage device or USB cable is
correctly inserted to the USB port of the unit.
0 Disconnect the USB storage device from the unit, and
then try reconnecting.
0 Performance of the hard disk that receive power from the
USB port of the unit is not guaranteed.
0 Depending on the type of format, the playback may not
be performed normally. Check the type of the file formats
that is supported.
0 USB storage devices with security functions may not be
played.
■ Wireless LAN Network
0 Try plugging/unplugging the power supply of wireless
LAN router and the unit, check the wireless LAN router
power-on status, and try reboot of the wireless LAN
router.
Check the following if the above does not fix the problem:
Cannot access wireless LAN network
0 The wireless LAN router setting may be switched to
Manual. Return the setting to Auto.
0 Try the manual set-up. The connection may succeed.
0 When the wireless LAN router setting is at stealth mode
(mode to hide the SSID key) or when ANY connection is
off, the SSID is not displayed. Change the setting and try
again.
0 Check that the setting of SSID and encryption (WEP,
etc.) is correct. Make sure the network settings of the unit
is properly set.
0 Connection to an SSID that includes multi-byte
characters is not supported. Name the SSID of the
wireless LAN router using single-byte alphanumeric
characters only and try again.
Connected to an SSID different to the SSID selected
0 Some wireless LAN routers allow you to set multiple
SSIDs for one unit. If you use the automatic setting
button on such a router, you may end up connecting with
a different SSID from the SSID you wanted to connect to.
Use the connection method requiring you to enter a
password if this happens.
Playback is interrupted and communication does not
work
0 You may not receive radio waves due to bad radio wave
conditions. Shorten the distance from the wireless LAN
access point or remove obstacles to improve visibility,
and try again. Place the unit away from microwave ovens
or other access points. It is recommended to place the
wireless LAN router (access point) and the unit in the
same room.
0 If there is a metallic object near the unit, wireless LAN
connection may not be possible as the metal can effect
on the radio wave.
0 When other wireless LAN devices are used near the unit,
several issues such as interrupted playback and
communication may occur. You can avoid these issues
by changing the channel of your wireless LAN router. For
instructions on changing channels, see the instruction
manual provided with your wireless LAN router.
0 There may not be enough bandwidth available in
wireless LAN. Connect using an Ethernet cable.
■ Remote Controller
0 Make sure that the batteries are installed with the correct
polarity.
0 Install new batteries. Do not mix different types of
batteries, or old and new batteries.
0 Make sure that this unit is not subjected to direct
sunshine or inverter-type fluorescent lights. Relocate if
necessary.
0 If this unit is installed in a rack or cabinet with coloredglass doors or if the doors are closed, the remote
controller may not work reliably.
■ Display, OSD
The display doesn't light
0 The display may go dim while the Dimmer is working,
and may also turn off. Press Dimmer button and change
the brightness level of the display.
75
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
■ Others
Strange noises can be heard from this unit
0 If you have connected another unit to the same wall
outlet as this unit, this noise may be an effect from the
other unit. If the symptoms improve by unplugging the
power cord of the other unit, use different wall outlets for
this unit and the other unit.
When performing AccuEQ Room Calibration, the
message "Noise Error" appears
0 This can be caused by a malfunction in your speaker
unit. Check if the unit produces normal sounds.
76
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
General Specifications
Amplifier (Audio) section
Network Section
Rated Output Power (FTC)
With 4 ohm loads, both channels driven, from 1 kHz;
rated 50 watts per channel minimum RMS power, with no
more than 1% total harmonic distortion from 250
milliwatts to rated output.
Surround Mode Output Power ( * )
(4 ohms, 1 kHz THD 1%) 80 W per channel
Ethernet LAN
10BASE-T/100BASE-TX
Wireless LAN
IEEE 802.11 a/b/g/n standard
(Wi-Fi® standard)
5 GHz/2.4 GHz band
* Reference output for each speakers.
Depending on the source and the listening mode settings, there
may be no sound output.
Input Sensitivity and Impedance (1 kHz 80 W/4 Ω)
200 mV/47 kΩ (LINE (Unbalance))
6.0 mV/47 kΩ (PHONO MM)
Rated RCA Output Level and Impedance
1 V/470 Ω (SUBWOOFER PRE OUT)
Phono Overload
30 mV (MM 1 kHz 1%)
Frequency Response
10 Hz - 40 kHz/i1 dB, j3 dB
Tone Control Characteristics
n10 dB, 90 Hz (BASS)
n10 dB, 7.5 kHz (TREBLE)
Signal to Noise Ratio
80 dB (IHF-A, LINE IN, SP OUT)
70 dB (IHF-A, PHONO IN, SP OUT)
Speaker Impedance
4Ω-8Ω
Headphone Output Impedance
102 Ω
Headphone Rated Output
85 mW (32 Ω, 1 kHz, 10% THD)
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz
Preset Channel
40
BLUETOOTH Section
Communication system
BLUETOOTH Specification version 4.1+LE
Frequency band
2.4 GHz band
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH profiles
A2DP 1.2
AVRCP 1.3
HOGP-Host (Client)
HOGP-HID Device (Server)
HID Service (HIDS)
Supported Codecs
SBC
AAC
Transmission range (A2DP)
20 Hz - 20 kHz (Sampling frequency 44.1 kHz)
Maximum communication range
Line of sight approx. 15 m ( * )
* The actual range will vary depending on factors such as
obstacles between devices, magnetic fields around a microwave
oven, static electricity, cordless phone, reception sensitivity,
antenna’s performance, operating system, software application,
etc.
General
16 W (No-sound)
2 W (HDMI Standby Through)
2.6 W (Network Standby)
Dimensions (W k H k D)
435 mm k 70 mm k 325.5 mm
17-1/8" k 2-3/4" k 12-13/16"
Weight
4 kg (8.8 lbs)
HDMI
Input
IN1 (BD/DVD, HDCP2.2), IN2 (CBL/SAT, HDCP2.2), IN3
(STRM BOX, HDCP2.2), IN4 (GAME, HDCP2.2)
Output
OUT (HDCP2.2)
Supported
Deep Color, x.v.ColorTM, LipSync, Audio Return Channel,
3D, 4K 60Hz, CEC, Extended Colorimetry (sYCC601,
Adobe RGB, Adobe YCC601), Content Type, HDR
Audio Format
Dolby TrueHD, Dolby Digital, Dolby Digital Plus, Dolby
Atmos (to be supported in a future update), DTS, DTS:X
(to be supported in a future update), DTS-HD Master
Audio, DTS-HD High Resolution Audio, DTS 96/24, DTSHD Express, DSD, PCM
Maximum Video Resolution
4k 60 Hz (YCbCr 4:4:4)
Audio Inputs
Digital
OPTICAL (TV)
COAXIAL (CD)
Analog
1 (BD/DVD), 2 (CBL/SAT), PHONO (designated)
Power Supply
AC 100 - 240 V, 50/60 Hz
Power Consumption
60 W
0.2 W (Stand-by)
77
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
Audio Outputs
Analog
SUBWOOFER PRE OUT
Speaker Outputs
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER
Phones
Phones (Front, φ3.5 mm)
Others
USB: 1 (Front, Ver.2.0, 5 V/1 A)
Ethernet: 1
Setup Mic: 1
IR IN: 1
78
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
About HDMI
Compatible functions
HDMI (High Definition Multimedia Interface) is a digital
interface standard for connecting TVs, projectors, Blu-ray
Disc/DVD players, set-top boxes, and other video
components. Until now, several separate video and audio
cables have been required to connect AV components. With
HDMI, a single cable can carry control signals, digital video,
and digital audio (2-channel PCM, multichannel digital
audio, and multichannel PCM).
HDMI CEC functionality: By connecting devices and HDMI
cables that comply with the CEC (Consumer Electronics
Control) specification of the HDMI standard, a variety of
linked operation become possible between devices. You
can enjoy features such as linking input switching with the
input selector and players, control volume using the remote
controller of the TV, and automatically switching this unit to
standby when the TV is turned off. The unit is designed to
link with products that comply with the CEC standard, and
that linked operation is not always guaranteed with all CEC
devices.
ARC (Audio Return Channel): By connection a TV that
supports ARC with a single HDMI cable, you can not only
output the audio and video from this unit to the TV, but also
input the audio from the TV to this unit.
HDMI Standby Through: Even if this unit is in standby, the
input signals from AV components are transmitted to the TV.
Deep Color: By connecting devices supporting Deep Color,
video signals input from the devices can be reproduced on
the TV with even more colors.
x.v.Color™: This technology realizes even more realistic
colors by broadening the color gamut.
3D: You can transmit 3D video signals from AV components
to the TV.
4K: This unit supports 4K (3840
(4096
2160p) video signals.
2160p) and 4K SMPTE
LipSync: This setting automatically corrects any
desynchronization between the video and audio signals
based on data from the HDMI LipSync compatible TV.
Supported Audio Formats
2-channel linear PCM: 32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit
Multi-channel linear PCM: Maximum 5.1 channels,
32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz, 16/20/24 bit
Bitstream: Dolby Digital, Dolby Digital Plus, Dolby TrueHD,
DTS, DTS-HD High Resolution Audio, DTS-HD Master
Audio
DSD: Supported sampling rates: 2.8 MHz
Your Blu-ray Disc/DVD player must also support HDMI
output of the above audio formats.
Supported resolutions
Copyright protection technology: HDCP1.4/HDCP2.2
Color space (Color Depth): 720
480i 60Hz, 720
576i
50Hz, 720 480p 60Hz, 720 576p 50Hz, 1920 1080i 50/
60Hz, 1280 720p 24/25/30/50/60Hz, 1680 720p 24/25/
30/50/60Hz, 1920 1080p 24/25/30/50/60Hz, 2560 1080p
24/25/30/50/60Hz, 4K (3840
2160p) 24/25/30Hz, 4K
SMPTE (4096
2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8/
10/12 bit), YCbCr4:2:2 (12 bit)
4K (3840 2160p) 50/60Hz, 4K SMPTE (4096 2160p) 50/
60Hz : RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit),
YCbCr4:2:0 (8/10/12 bit)
79
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information | Advanced Setup | Others
License and Trademark Information
AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac
with OS X Mountain Lion or later, and PC with iTunes 10.2.2 or later.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos,
Dolby Surround and the double-D symbol are trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, the DTS-HD
logo, and DTS-HD Master Audio are registered trademarks or trademarks of
DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights
Reserved.
“CINEMA FILTER” and “CINEMA FILTER (logo)” are trademarks of Onkyo
Corporation.
®
The BLUETOOTH® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Onkyo Corporation is under
license. Other trademarks and trade names are those of their respective
owners.
Onkyo Corporation does not guarantee BLUETOOTH compatibility between the
AV receiver and all BLUETOOTH enabled devices.
For compatibility between the AV receiver and another device with
BLUETOOTH technology, consult the device’s documentation and dealer. In
some countries, there may be restrictions on using BLUETOOTH devices.
Check with your local authorities.
PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks
or registered trademarks of Pandora Media, Inc. Used with permission.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
The product with this logo is conformed to Hi-Res Audio standard defined by
Japan Audio Society. This logo is used under license from Japan Audio Society.
The Wi-Fi CERTIFIED Logo is a certification mark of Wi-Fi
Alliance®.
This product is protected by certain intellectual property rights of Microsoft. Use
or distribution of such technology outside of this product is prohibited without a
license from Microsoft.
Windows and the Windows logo are trademarks of the Microsoft group of
companies.
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
AirPlay, iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
“x.v.Color” and “x.v.Color” logo are trademarks of Sony Corporation.
iPad Air and iPad mini are trademarks of Apple Inc.
DSD and the Direct Stream Digital logo are trademarks of Sony Corporation.
“Made for iPod”, “Made for iPhone” and “Made for iPad” mean that an electronic
accessory has been designed to connect specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
Thomson.
Please note that the use of this accessory with iPod, iPhone or iPad may affect
wireless performance.
80
AccuEQ and Music Optimizer are trademarks of Onkyo Corporation.
“All other trademarks are the property of their respective owners.”
1-10-5 Yokoami, Sumida-ku, Tokyo 130-0015 JAPAN
http://www.integraworldwide.com
<U.S.A.>
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650
http://www.integrahometheater.com
<Germany>
Gutenbergstrasse 3, 82178 Puchheim, Germany
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.integra.eu
<PRC>
302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032,
Tel: +86-21-52131366 Fax: +86-21-52130396
http://www.integra.com.cn
F1711-4
(C) Copyright 2016 Onkyo & Pioneer Corporation Japan. All rights reserved.
SN 29402692D
http://www.onkyo.com/privacy/
* 2 9 4 0 2 6 9 2 D *
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising