Integra | DRX-2 | Owner Manual | Integra DRX-2 Receiver Owner Manual

Integra DRX-2 Receiver Owner Manual
Specifications
General Specifications
Amplifier Section
Rated Output Power (FTC) (North American)
With 8 ohm loads, both channels driven, from 20­20,000 Hz; rated 80
watts per channel minimum RMS power, with no more than 0.08%
total harmonic distortion from 250 milliwatts to rated output.
Surround Mode Output Power (*)
(6 ohms, 1 kHz THD 0.9%) 140 W per channel
* Reference output for each speakers.
Depending on the source and the listening mode settings, there may
be no sound output.
Rated Output Power (IEC) (Others)
7 ch × 130 W at 6 ohms, 1 kHz, 1 ch driven of 1% THD
Maximum Effective Output Power (JEITA) (Australian)
7 ch × 160 W at 6 ohms, 1 kHz, 1 ch driven of 10% THD
Dynamic Power (*)
* IEC60268­Short­term maximum output power
160 W (3 Ω, Front)
125 W (4 Ω, Front)
85 W (8 Ω, Front)
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz ­ 20,000 Hz, half power)
Input Sensitivity and Impedance (1 kHz 100 W/8 Ω)
200 mV/47 kΩ (LINE (Unbalance))
3.5 mV/47 kΩ (PHONO MM)
Rated RCA Output Level and Impedance
1 V/470 Ω (SUBWOOFER PRE OUT)
200 mV/2.3 kΩ (ZONE LINE OUT)
2 V/2.3 kΩ (ZONE PREOUT)
Phono Overload
70 mV (MM 1 kHz 0.5%)
Frequency Response
5 Hz ­ 100 kHz/+1 dB, –3 dB (Direct)
Tone Control Characteristics
±10 dB, 90 Hz (BASS)
±10 dB, 7.5 kHz (TREBLE)
Signal to Noise Ratio
106 dB (IHF­A, LINE IN, SP OUT)
80 dB (IHF­A, PHONO IN, SP OUT)
Speaker Impedance
6 Ω ­ 16 Ω
Headphone Output Impedance
330 Ω
Headphone Rated Output
85 mW (32 Ω, 1 kHz, 10% THD)
Video Section
Signal level
1 Vp­p/75 Ω (Composite Video)
1 Vp­p/75 Ω (Component Video Y)
0.7 Vp­p/75 Ω (Component Video B/R)
Maximum resolution supported by component video
480i/576i
Tuner Section
FM Tuning Frequency Range
87.5 MHz ­ 107.9 MHz (North American)
87.5 MHz ­ 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
530 kHz ­ 1710 kHz (North American)
522/530 kHz ­ 1611/1710 kHz (Others)
Preset Channel
40
Network Section
Ethernet LAN
10BASE­T/100BASE­TX
Wireless LAN
IEEE 802.11 a/b/g/n standard
(Wi­Fi® standard)
5 GHz/2.4 GHz band
BLUETOOTH Section
Communication system
BLUETOOTH Specification version 4.1+LE
Frequency band
2.4 GHz band
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH profiles
A2DP 1.2
AVRCP 1.3
HOGP­Host (Client)
HOGP­HID Device (Server)
HID Service (HIDS)
Supported Codecs
SBC
AAC
Transmission range (A2DP)
20 Hz ­ 20 kHz (Sampling frequency 44.1 kHz)
Maximum communication range
Line of sight approx. 15 m (*)
* The actual range will vary depending on factors such as obstacles
between devices, magnetic fields around a microwave oven, static
electricity, cordless phone, reception sensitivity, antenna's
performance, operating system, software application, etc.
General
Power Supply
AC 120 V, 60 Hz (North American)
AC 220 ­ 240 V, 50/60 Hz (Others)
Power Consumption
460 W (North American)
450 W (Others)
0.1 W (Stand­by, North American)
0.15 W (Stand­by, Others)
55 W (No­sound)
4.9 W (HDMI Standby Through, North American)
5.1 W (HDMI Standby Through, Others)
2.4 W (Network Standby)
Dimensions (W × H × D)
435 mm × 174 mm × 376.5 mm
17­1/8" × 6­7/8" × 14­13/16"
Weight
9.4 kg (20.7 lbs.) (North American)
9.6 kg (21.2 lbs.) (Others)
HDMI
Input
IN1 (BD/DVD, HDCP2.2), IN2 (CBL/SAT, HDCP2.2), IN3 (STRM BOX,
HDCP2.2), IN4 (GAME), IN5 (PC), IN6
Output
OUT
Supported
Deep Color, x.v.Color™, LipSync, Audio Return Channel, 3D, 4K 60
Hz, CEC, Extended Colorimetry (sYCC601, Adobe RGB, Adobe
YCC601), Content Type, HDR
Audio Format
Dolby Atmos, Dolby TrueHD, Dolby Digital, Dolby Digital Plus, DTS,
DTS:X (to be supported in a future update), DTS­HD Master Audio,
DTS­HD High Resolution Audio, DTS 96/24, DTS­ES, DTS­HD
Express, DSD, PCM
Maximum Video Resolution
4k 60 Hz (YCbCr 4:4:4)
Video Inputs
Component
IN1 (BD/DVD), IN2 (GAME)
Composite
IN1 (CBL/SAT), IN2 (STRM BOX)
Compatible input resolutions
HDMI input
4K, 1080p/24, 1080p, 1080i, 720p, 480p/576p
Component input
480i/576i
Composite input
480i/576i
The output from the HDMI OUT jack to the TV is the same resolution as
the input. When using a TV that supports 4K, 1080p HDMI video signals
can also be output as 4K.
Audio Inputs
Digital
OPTICAL 1 (CD), 2 (TV)
COAXIAL (BD/DVD)
Analog
BD/DVD, CBL/SAT, GAME, STRM BOX, CD, TV, PHONO, AUX (front)
Audio Outputs
Analog
ZONE2 PRE/LINE OUT
2 SUBWOOFER PRE OUT
Speaker Outputs
FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK or
HEIGHT L/R or Bi­Amp L/R, ZONE2 L/R
(North American models are banana plug ready)
Phones
PHONES (Front, ø 6.3 mm, 1/4")
Others
Setup Mic : 1 (Front)
USB : 1 (Ver. 2.0, 5 V/1 A)
Ethernet : 1
RS232: 1
12V TRIGGER OUT: (A: 100 mA, B: 25 mA, C: 25 mA)
IR IN: 2 (A/B)
IR OUT: 1
Power consumption in standby mode
In the following cases, the power consumption in standby mode may
reach up to a maximum of 12 W:
– When "Network Standby" is set to "On"
– When "HDMI CEC" is set to "On"
– When "HDMI Standby Through" is set to other than "Off"
– When "Bluetooth Wakeup" is set to "On"
– When "USB Power Out at Standby" is set to "On"
Specifications and features are subject to change without notice.
Specifications
About HDMI
Compatible functions
HDMI (High Definition Multimedia Interface) is a digital interface standard for
connecting TVs, projectors, Blu­ray Disc/DVD players, set­top boxes, and
other video components. Until now, several separate video and audio cables
have been required to connect AV components. With HDMI, a single cable
can carry control signals, digital video and digital audio (2 ch PCM,
multichannel digital audio, and multichannel PCM).
HDMI CEC functionality:
By connecting devices and HDMI cables that comply with the CEC
(Consumer Electronics Control) specification of the HDMI standard, a variety
of linked operation become possible between devices. You can enjoy
features such as linking input switching with the input selector and players,
control volume using the remote controller of the TV, and automatically
switching this unit to standby when the TV is turned off.
The unit is designed to link with products that comply with the CEC standard,
and that linked operation is not always guaranteed with all CEC devices. For
linked functions to work properly, do not connect more CEC­compliant
components than the quantities specified below, to the HDMI jack.
Blu­ray Disc/DVD players: up to 3 units.
Blu­ray Disc/DVD recorders: up to 3 units.
Cable TV tuner, terrestrial digital tuner, and satellite broadcasting tuner:
up to 4 units.
Operation has been confirmed on the following devices: (As of February
2016)
Toshiba brand televisions; Sharp brand televisions; Onkyo and Integra brand
RIHD­compatible players; Toshiba brand players and recorders; Sharp brand
players and recorders (when used with a Sharp brand television)
ARC(Audio Return Channel):
By connection a TV that supports ARC with a single HDMI cable, you can
not only output the audio and video from this unit to the TV, but also input the
audio from the TV to this unit.
HDMI Standby Through:
Even if this unit is in standby, the input signals from AV components are
transmitted to the TV.
Deep Color:
By connecting devices supporting Deep Color, video signals input from the
devices can be reproduced on the TV with even more colors.
x.v.Color™:
This technology realizes even more realistic colors by broadening the color
gamut.
3D:
You can transmit 3D video signals from AV components to the TV.
4K:
This unit supports 4K (3840×2160p) and 4K SMPTE (4096×2160p) video
signals.
LipSync:
This setting automatically corrects any desynchronization between the video
and audio signals based on data from the HDMI LipSync compatible TV.
Copyright Protection:
The unit supports Revision 1.4 and Revision 2.2 (HDMI OUT and HDMI IN1
to 3 only) of the HDCP (High­bandwidth Digital Content Protection), a copy­
protection system for digital video signals. Other devices connected to the
unit must also support HDCP.
Supported Audio Formats
2 ch linear PCM:
32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz,
16/20/24 bit
Multi­channel linear PCM:
Maximum 7.1 channels, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz, 16/20/24 bit
Bitstream:
Dolby Atmos, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS:X
(to be supported in a future update), DTS­HD High Resolution Audio, DTS­
HD Master Audio
DSD:
Supported sampling rates: 2.8 MHz
Your Blu­ray Disc/DVD player must also support HDMI output of the above
audio formats.
Supported resolutions
HDMI IN1 to IN3:
Copyright protection technology: HDCP1.4/HDCP2.2
Color space (Color Depth):
– 720×480i 60Hz, 720×576i 50Hz, 720×480p 60Hz, 720×576p 50Hz,
1920×1080i 50/60Hz, 1280×720p 24/25/30/50/60Hz, 1680×720p
24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz, 2560×1080p
24/25/30/50/60Hz, 4K (3840×2160p) 24/25/30Hz, 4K SMPTE
(4096×2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8/10/12 bit),
YCbCr4:2:2 (12 bit)
– 4K (3840×2160p) 50/60Hz, 4K SMPTE (4096×2160p) 50/60Hz :
RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit), YCbCr4:2:0 (8/10/12 bit)
HDMI IN4 to IN6:
Copyright protection technology: HDCP1.4
Color space (Color Depth):
– 720×480i 60Hz, 720×576i 50Hz, 720×480p 60Hz, 720×576p 50Hz,
1920×1080i 50/60Hz, 1280×720p 24/25/30/50/60Hz, 1680×720p
24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz, 2560×1080p
24/25/30/50/60Hz : RGB/YCbCr4:4:4 (8/10/12 bit), YCbCr4:2:2 (12 bit)
– 4K (3840×2160p) 24/25/30Hz, 4K SMPTE (4096×2160p) 24/25/30Hz :
RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit)
– 4K (3840×2160p) 50/60Hz, 4K SMPTE (4096×2160p) 50/60Hz :
YCbCr4:2:0 (8 bit)
Settings
Setup Menu
The unit allows you to configure advanced settings to provide you with an
even better experience.
Operation:
Use the on­screen displays (OSD) that appear on the TV to make the
settings.
Press
on the remote controller to display the Setup menu.
Select the item with the cursor / buttons of the remote controller and
press Enter to confirm your selection.
Use the cursors / to change the default values.
To return to the previous screen, press .
To exit the settings, press .
1. Input/Output Assign
Make settings related to output to the TV, change the settings for jack
allocations to the various input selectors, and set the feature for displaying
operations on the TV (OSD), etc.
1. TV Out / OSD
1080p ­> 4K Upscaling
Default Value: Off
When using a TV that supports 4K, video signals input at 1080p can be
automatically upscaled to 4K for output.
"Off": Do not use this function
"Auto": Use this function
Select "Off" if your TV does not support 4K.
Super Resolution
Default Value: (2)
When you have set "1080p ­> 4K Upscaling" to "Auto", you can select
the degree of video signal correction from "Off" and between "1" (weak)
and "3" (strong).
OSD Language
Default Value: English
Select the on­screen display language from the following.
English, German, French, Spanish, Italian, Dutch, Swedish, Russian,
Chinese
Impose OSD
Default Value: On
Set whether or not to display the information on the TV when the
volume is adjusted or input is changed, for example.
"On": OSD displayed on the TV.
"Off": OSD not displayed on the TV.
OSD may not be displayed depending on the input signal even if
"On" is selected. If the operation screen is not displayed, change the
resolution of the connected device.
Screen Saver
Default Value: 3 minutes
Set the time to start the screen saver.
Select a value from "3 minutes", "5 minutes", "10 minutes" and "Off".
2. HDMI Input
You can change input assignment between the input selectors and HDMI IN
jacks.
BD/DVD
Default Value: HDMI 1 (HDCP 2.2)
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the BD/DVD button. If you do not assign a jack, select "­­­­­". To select
an HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
CBL/SAT
Default Value: HDMI 2 (HDCP 2.2)
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the CBL/SAT button. If you do not assign a jack, select "­­­­­". To select
an HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
GAME
Default Value: HDMI 4
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the Game button. If you do not assign a jack, select "­­­­­". To select an
HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
STRM BOX
Default Value: HDMI 3 (HDCP 2.2)
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the STRM Box button. If you do not assign a jack, select "­­­­­". To
select an HDMI IN jack already assigned to another input selector,
change its setting to "­­­­­" first.
PC
Default Value: HDMI 5
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the PC button. If you do not assign a jack, select "­­­­­". To select an
HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
CD
Default Value: ­­­­­
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the CD button. If you do not assign a jack, select "­­­­­". To select an
HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
TV
Default Value: ­­­­­
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the TV button. If you do not assign a jack, select "­­­­­". To select an
HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
PHONO
Default Value: ­­­­­
"HDMI 1 (HDCP 2.2)" to "HDMI 6": Assign a desired HDMI IN jack to
the Phono button. If you do not assign a jack, select "­­­­­". To select an
HDMI IN jack already assigned to another input selector, change its
setting to "­­­­­" first.
3. Video Input
You can change input assignment between the input selectors and
COMPONENT VIDEO IN 1 and 2 jacks and the VIDEO IN 1 and 2 jacks. If
you do not assign a jack, select "­­­­­".
BD/DVD
Default Value: COMPONENT 1
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the BD/DVD button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the BD/DVD
button.
CBL/SAT
Default Value: VIDEO 1
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the CBL/SAT button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the CBL/SAT
button.
GAME
Default Value: COMPONENT 2
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the Game button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the Game
button.
STRM BOX
Default Value: VIDEO 2
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the STRM Box button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the STRM
Box button.
PC
Default Value: ­­­­­
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the PC button.
"VIDEO 1" to "VIDEO 2": Assign a desired VIDEO IN jack to the PC
button.
CD
Default Value: ­­­­­
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the CD button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the CD
button.
TV
Default Value: ­­­­­
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the TV button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the TV
button.
PHONO
Default Value: ­­­­­
"COMPONENT 1", "COMPONENT 2": Assign the COMPONENT
VIDEO IN jacks to the Phono button.
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the Phono
button.
4. Digital Audio Input
You can change input assignment between the input selectors and DIGITAL
IN COAXIAL/OPTICAL 1 to 2 jacks. If you do not assign a jack, select "­­­­­".
BD/DVD
Default Value: COAXIAL
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the BD/DVD button.
CBL/SAT
Default Value: ­­­­­
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the CBL/SAT button.
GAME
Default Value: ­­­­­
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the Game button.
STRM BOX
Default Value: ­­­­­
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the STRM Box button.
PC
Default Value: ­­­­­
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the PC button.
CD
Default Value: OPTICAL 1
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the CD button.
TV
Default Value: OPTICAL 2
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the TV button.
PHONO
Default Value: ­­­­­
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN
jack to the Phono button.
Supported sampling rates for PCM signals (stereo, mono) from a digital
input are 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz/16bit, 20bit, and 24bit.
5. Analog Audio Input
You can change input assignment between the input selectors and AUDIO
IN jacks. If you do not assign a jack, select "­­­­­".
BD/DVD
Default Value: AUDIO 1
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the
BD/DVD button.
CBL/SAT
Default Value: AUDIO 2
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the
CBL/SAT button.
GAME
Default Value: AUDIO 3
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the Game
button.
STRM BOX
Default Value: AUDIO 4
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the STRM
Box button.
PC
Default Value: ­­­­­
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the PC
button.
CD
Default Value: AUDIO 5
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the CD
button.
TV
Default Value: AUDIO 6
"AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the TV
button.
PHONO
Default Value: (PHONO)
The setting cannot be changed.
2. Speaker
You can make changes to the connection environment of the speakers and
change the volume level. Settings are automatically configured if you use
AccuEQ Room Calibration. This setting cannot be selected if headphones
are connected or audio is output from the speakers of the TV.
1. Configuration
Speaker Channels
Default Value: 7.1 ch
Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1 ch", "7.1 ch", "2.1.2 ch",
"3.1.2 ch", "4.1.2 ch", or "5.1.2 ch" to suit the number of speaker
channels connected.
Subwoofer
Default Value: Yes
Set whether a subwoofer is connected or not.
"Yes": When subwoofer is connected
"No": When subwoofer is not connected
Height Speaker
Default Value: (Top Middle)
Set the speaker type if height speakers are connected to the
SURROUND BACK or HEIGHT terminals.
Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High",
"Dolby Speaker (Front)", or "Dolby Speaker (Surr)" according to the
type and layout of the connected speakers.
If an item cannot be selected even though connection is correct,
check that the settings in "Speaker Channels" matches the number
of connected channels.
Zone Speaker
Default Value: No
Set the connection of speakers to Zone 2 speaker terminals.
"Zone 2": When speakers are connected to Zone 2 speaker terminals
"No": When speakers are not connected to Zone 2 speaker terminals
Bi­Amp
Default Value: No
Set whether the front speakers are bi­amp connected.
"No": When front speakers are not bi­amp connected
"Yes": When front speakers are bi­amp connected
This item will be fixed to "No" when the "Zone Speaker" setting is
"Zone 2".
If an item cannot be selected even though connection is correct,
check that the settings in "Speaker Channels" matches the number
of connected channels.
2. Crossover
Front
Default Value: 100Hz
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel.
"Full Band": Full band will be output.
If "Configuration" ­ "Subwoofer" is set to "No", "Front" will be fixed to
"Full Band" and the low pitched range of the other channels will be
output from the front speakers. Refer to the instruction manual of
your speakers to make the setting.
Center
Default Value: 100Hz
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is set to "Full Band".
If an item cannot be selected even though connection is correct,
check that the settings in "Configuration" ­ "Speaker Channels"
matches the number of connected channels.
Height
Default Value: (100Hz)
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is set to "Full Band".
If an item cannot be selected even though connection is correct,
check that the settings in "Configuration" ­ "Speaker Channels"
matches the number of connected channels.
Surround
Default Value: 100Hz
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is set to "Full Band".
If an item cannot be selected even though connection is correct,
check that the settings in "Configuration" ­ "Speaker Channels"
matches the number of connected channels.
Surround Back
Default Value: 100Hz
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Surround" is set to "Full
Band".
If an item cannot be selected even though connection is correct,
check that the settings in "Configuration" ­ "Speaker Channels"
matches the number of connected channels.
LPF of LFE
Default Value: 120Hz
Set the low­pass filter for LFE (low­frequency effect) signals in order to
pass lower frequency signals than the set value and thus cancel
unwanted noises. The low­pass filter will be effective only on sources
with LFE channel.
The value from "80Hz" to "120Hz" can be set.
"Off": Do not use this function
Double Bass
Default Value: (On)
This can be selected only when "Configuration" ­ "Subwoofer" is set to
"Yes" and "Front" is set to "Full Band".
Boost bass output by feeding bass sounds from the front left and right,
and center speakers to the subwoofer.
"On": Bass output will be boosted
"Off": Bass output will not be boosted
The setting will not automatically be configured even if you
performed AccuEQ Room Calibration.
3. Distance
Set the distance from each speaker to the listening position.
Front Left
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Center
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Front Right
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Height Left
Default Value: (9.0ft/2.70m)
Specify the distance between each speaker and the listening position.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Height Right
Default Value: (9.0ft/2.70m)
Specify the distance between each speaker and the listening position.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Surround Right
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
Surr Back Right
Surr Back Right
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Surr Back Left
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Surround Left
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
Subwoofer
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Default values vary depending on the regions.
Distance units can be switched by pressing Mode on the remote
controller. When the unit is set as feet, you can set between 0.1 ft and
30.0 ft in increments of 0.1ft. When the unit is set as meters, you can set
between 0.03 m and 9.00 m in increments of 0.03 m.
4. Level Calibration
Front Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
Center
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
Front Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
Height Left
Default Value: (0 dB)
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Height Right
Default Value: (0 dB)
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Surround Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
Surr Back Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Surr Back Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
The setting cannot be changed if "Zone 2" is set in "Configuration" ­
"Zone Speaker" and Zone 2 is on.
Surround Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
Subwoofer
Default Value: 0 dB
Select a value between "-15 dB" and "+12 dB" (in 1 dB increments).
A test tone will be output each time you change the value. Select the
desired level.
5. Dolby Enabled Speaker
Dolby Enabled Speaker to Ceiling
Default Value: (6.0 ft/1.80 m)
Set the distance between the Dolby Enabled Speaker and the ceiling.
Select between "0.1 ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).
The unit of distance (ft/m) shown is the unit selected for use in
"Distance".
AccuReflex
Default Value: (Off)
You can enhance the reflection effect of Dolby Enabled Speakers from
the ceiling.
"Off": Do not use this function
"On": Use this function
6. Equalizer Settings
You can adjust the output volume of the range of each connected speaker.
You can adjust the volume of the different sound ranges for each of the
speakers. You can set three different equalizers in Preset 1 to 3. You can
select up to five bands for the Subwoofer and fifteen bands for all other
speakers.
Front
Default Value: 0 dB
After selecting the speaker frequency from between 25 Hz" and "16
kHz" with the cursors / , adjust the volume of that frequency between
"-6 dB" and "+6 dB" with / .
Center
Default Value: 0 dB
After selecting the speaker frequency from between 25 Hz" and "16
kHz" with the cursors / , adjust the volume of that frequency between
"-6 dB" and "+6 dB" with / .
Height
Default Value: (0 dB)
After selecting the speaker frequency from between 25 Hz" and "16
kHz" with the cursors / , adjust the volume of that frequency between
"-6 dB" and "+6 dB" with / .
This cannot be selected if "Zone 2" is set in "Configuration" ­ "Zone
Speaker" and Zone 2 is on.
Surround
Default Value: 0 dB
After selecting the speaker frequency from between 25 Hz" and "16
kHz" with the cursors / , adjust the volume of that frequency between
"-6 dB" and "+6 dB" with / .
Surround Back
Default Value: 0 dB
After selecting the speaker frequency from between 25 Hz" and "16
kHz" with the cursors / , adjust the volume of that frequency between
"-6 dB" and "+6 dB" with / .
This cannot be selected if "Zone 2" is set in "Configuration" ­ "Zone
Speaker" and Zone 2 is on.
Subwoofer
Default Value: 0 dB
After selecting the speaker frequency from between 25 Hz" and "160
Hz" with the cursors / , adjust the volume of that frequency between
"-6 dB" and "+6 dB" with / .
This cannot be selected if "No" is set in "Configuration" ­
"Subwoofer".
The result may not be as expected depending on the input source and
listening mode setting.
3. Audio Adjust
Make advanced settings such as those related to multiplex audio, settings
for the LFE level, or those related to the volume of this unit.
1. Multiplex/Mono
Multiplex Input Channel
Default Value: Main
Set the audio channel or language to be output when playing multiplex
audio or multilingual TV broadcasts etc.
"Main": Main channel only
"Sub": Sub channel only
"Main/Sub": Main and sub channels will be output at the same time.
If multiplex audio is being played, "1+1" will be displayed when
on the remote controller is pressed.
Mono Input Channel
Default Value: Left + Right
Set the input channel to use for playing any 2 ch digital source such as
Dolby Digital, or 2 ch analog/PCM source in the Mono listening mode.
"Left": Left channel only
"Right": Right channel only
"Left + Right" : Left and right channels
2. Dolby
Loudness Management
Default Value: On
When playing Dolby TrueHD, enable the dialog normalization function
which keeps the volume of dialog at a certain level. Note that when this
setting is Off, the Late Night function that allows you to enjoy surround
at low volumes is fixed to off when playing Dolby Digital Plus/Dolby
TrueHD.
"On": Use this function
"Off": Do not use this function
3. LFE Level
Set the low­frequency effect (LFE) level for Dolby Digital series, DTS series,
Multichannel PCM, and DSD signals.
LFE Level
Default Value: 0 dB
Select the low­frequency effect (LFE) level of each type of signal from
"0dB" to "-∞dB". If the low­frequency effect sound is too strong, select
"-20dB" or "-∞dB".
4. Volume
Mute Level
Default Value: -∞dB
Set the volume lowered from the listening volume when muting is on.
Select a value from "-∞dB", "-40dB", and "-20dB".
Maximum Volume
Default Value: Off
Set the maximum value to avoid too high volume. Select a value from
"Off", "50" to "99".
Power On Volume
Default Value: Last
Set the volume level of when the power is turned on. Select a value
from "Last" (Volume level before entering standby mode), "Min", "1" to
"99" and "Max".
You cannot set a higher value than that of "Maximum Volume".
Headphone Level
Default Value: 0 dB
Adjust the output level of the headphones. Select a value between "-
12 dB" and "+12 dB".
4. Source
Make settings for input sources, such as volume difference adjustments for
each input selector for the connected equipment.
1. IntelliVolume
Adjust the volume level difference between the devices connected to the
unit. Select the input selector to configure.
IntelliVolume
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". Set a negative value
if the volume of the target device is larger than the others and a positive
value if smaller. To check the audio, start playback of the connected
device.
This function is not effective in Zone 2.
2. Name Edit
Set an easy name to each input. The set name will be shown on the main
unit display. Select the input selector to configure.
Name Edit
Default Value: Input name
1. Select a character or symbol with the cursors and press Enter.
Repeat it to input 10 or less characters.
"A/a": Switches between upper and lower cases. (Pressing Mode on
the remote controller also toggles between upper and lower cases)
"←" "→": Moves the cursor to the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
Pressing Clear on the remote controller will remove all the input
characters.
2. After inputting, select "OK" with the cursors and press Enter.
The input name will be saved.
To name a preset radio station, press Tuner on the remote controller,
select AM/FM and select the preset number.
This cannot be set if the "NET" or "BLUETOOTH" input is selected.
Audio Select
Select the priority for input selection when multiple audio sources are
connected to one input selector, such as connections to both the "BD/DVD"
HDMI IN jack and the "BD/DVD" AUDIO IN jack. The setting can be
separately set to each input selector button. Select the input selector to
configure.
Audio Select
Default Value: BD/DVD: HDMI CBL/SAT: HDMI GAME: HDMI
STRMBOX: HDMI PC: HDMI CD: OPTICAL PHONO: Analog TV:
OPTICAL
"ARC": When giving priority to input signal from ARC compatible TV.
The setting can be selected only when "6. Hardware" ­ "HDMI" ­
"Audio Return Channel" is set to "Auto" and also the "TV" input is
selected.
"HDMI": When giving priority to input signal from HDMI IN jacks
The setting can be selected only when the input is assigned to the
HDMI jack in the "1. Input/Output Assign" ­ "HDMI Input" setting.
"COAXIAL": When giving priority to input signal from DIGITIAL IN
COAXIAL jacks
The setting can be selected only when the input is assigned to the
COAXIAL jack in the "1. Input/Output Assign" ­ "Digital Audio Input"
setting.
"OPTICAL": When giving priority to input signal from DIGITIAL IN
OPTICAL jacks
The setting can be selected only when the input is assigned to the
OPTICAL jack in the "1. Input/Output Assign" ­ "Digital Audio Input"
setting.
"Analog": To always output analog audio independently of the input
signal
The setting can be selected only when the input is assigned to the
AUDIO IN jack in the "1. Input/Output Assign" ­ "Analog Audio Input"
setting.
PCM Fixed Mode
Default Value: Off
Select whether to fix input signals to PCM (except multi­channel PCM)
when you have selected "HDMI", "COAXIAL", or "OPTICAL" in the
"Audio Select" setting. Set this item to "On" if noise is produced or
truncation occurs at the beginning of a track when playing PCM
sources. Select "Off" normally.
Changing "Audio Select" changes the setting to "Off".
The setting cannot be changed when "TUNER", "NET", or "BLUETOOTH"
input is selected.
Video Select
When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the
input from which video is displayed on the TV.
Video Select
Default Value: Last
"Last": Select the video input played immediately prior.
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "PC", "AUX", "CD",
"TV", "PHONO": Play the video from the selected input.
This setting is effective for an input selector which is assigned in
"1. Input/Output Assign" ­ "HDMI Input" and "Video Input".
If the OSD language is set to Chinese, this setting cannot be selected.
5. Listening Mode Preset
You can preset your favorite listening mode to each input. (For example, you
can always apply straight decode to the Dolby TrueHD source of Blu­ray
Disc to play it in unchanged sound field.)
When the list of input sources is displayed, set the signal type and listening
mode.
Although it is possible to select the listening mode during playback, the
selected mode will be reset when the unit enters standby mode.
Analog/PCM
Default Value: All Ch Stereo
Set the listening mode for playing PCM signals of CD and analog
signals of record and cassette tape.
Dolby
Default Value: Dolby Surround
Set the listening mode for playing Dolby Digital, Dolby Digital Plus and
Dolby TrueHD signals.
Input signals are played as they are input if you select "Straight
Decode".
DTS
Default Value: DTS Neural:X (before updating to a version that
supports DTS:X audio: Straight Decode)
Set the listening mode for playing digital audio signals in DTS and DTS­
HD High Resolution formats. Select the listening mode specified for
Blu­ray or such other DTS­HD Master Audio source.
Input signals are played as they are input if you select "Straight
Decode".
Other
Default Value: Dolby Surround
Set the listening mode for playing audio such as DVD­audio and DSD
signals.
Input signals are played as they are input if you select "Straight
Decode".
Available listening modes vary depending on speaker configuration and
the input signal.
Setting "Last Valid" will always select the last selected mode.
Only "Analog" can be set to the "AUX", "TUNER" input.
"Digital", "Dolby" and "DSD" can be set to the "NET" input.
Only "Digital" can be set to the "BLUETOOTH" input.
6. Hardware
Make settings related to the HDMI CEC, HDMI Standby Through, ARC
features, settings related to network features, and settings related to power
management of the unit, such as Auto Standby and Network Standby.
1. HDMI
HDMI CEC
Default Value: Off
Setting to "On" enables the input selection link and other link functions
with HDMI connected CEC compliant device.
"On": Use this function
"Off": Do not use this function
When changing this setting, turn off and then on again the power of all
connected components.
Depending on the TV set, a link may need to be configured on the
TV.
Setting to "On" and closing the on­screen menu displays the name
of the CEC­compatible components and "CEC On" on the display.
Power consumption in standby mode may increase if "On" is set.
(Depending on the TV status, the unit will enter the normal standby
mode.)
If you operate the Master Volume dial on the main unit when this
setting is "On" and audio is output from the TV speakers, audio will
be output also from the speakers connected to the unit. If you want
to output from only either of them, change the unit or TV settings, or
reduce the volume of the unit.
If abnormal operation occurs when you set the setting to "On", set it
to "Off".
When connecting a non­CEC compatible component, or when you
are not sure whether it is compatible, set the setting to "Off".
HDMI Standby Through
Default Value: Off
When this is set to anything other than "Off", you can play the video and
audio of an HDMI connected player on the TV even if the unit is in
standby mode. Only "Auto" and "Auto(Eco)" can be selected if "HDMI
CEC" is set to "On". If you select anything else, set "HDMI CEC" to
"Off".
Power consumption in standby mode increases if set to anything
other than "Off".
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "PC", "AUX", "CD",
"TV", "PHONO": For example, if you select "BD/DVD", you can play the
equipment connected to the "BD/DVD" jack on the TV even if the unit is
in standby mode. Select this setting if you have decided which player to
use with this function.
"Last": You can play the video and audio of the input selected
immediately prior to the unit being switched to standby on the TV.
"Auto", "Auto (Eco)": Select one of these settings when you have
connected equipment that conforms to the CEC standard. You can play
the video and audio of the input selected on the TV, irrespective of what
input was selected immediately prior to the unit being switched to
standby, using the CEC link function.
To play players on the TV that do not conform to the CEC standard,
you will need to turn the unit on and switch to the relevant input.
When using TV that complies with the CEC standard, you can
reduce the power consumption in standby mode by selecting "Auto
(Eco)".
Audio TV Out
Default Value: Off
You can enjoy audio through the speakers of the TV while this unit is
on.
"On": Use this function
"Off": Do not use this function
The setting is fixed to "Auto" if "HDMI CEC" is set to "On". If you
change this setting, set "HDMI CEC" to "Off".
Listening mode cannot be changed while "Audio TV Out" is set to
"On" and audio is being output through the speakers of the TV.
Depending on your TV set or input signal of the component, audio
may not output through the speakers of the TV even if this setting is
set to "On". In such case, audio is output from the speakers of the
unit.
If you operate the Master Volume dial on this unit when audio that is
being input through this unit for output from the TV speakers, audio
is output from this unit. If you do not want to output audio from the
unit, change the unit or TV settings, or reduce the volume of the unit.
Audio Return Channel
Default Value: (Auto) (*)
You can enjoy sound of the HDMI connected ARC compatible TV
through the speakers connected to the unit.
* To use this function, set "HDMI CEC" to "On" in advance.
"Auto": When enjoying the TV sound through the speakers connected
to the unit
"Off": When not using the ARC function
Auto LipSync
Default Value: On
This setting automatically corrects any desynchronization between the
video and audio signals based on data from the HDMI LipSync
compatible TV.
"On": Automatic correction will be enabled
"Off": Automatic correction will be disabled
2. Network
When LAN is configured with a DHCP, set "DHCP" to "Enable" to
configure the setting automatically. ("Enable" is set by default) To assign
fixed IP addresses to each components, you must set "DHCP" to
"Disable" and assign an address to this unit in "IP Address" as well as set
information related to your LAN, such as Subnet Mask and Gateway.
Wi­Fi
Default Value: Off(Wired)
Connect the unit to network via wireless LAN router.
"On": Wireless LAN connection
"Off(Wired)": Wired LAN connection
Wi­Fi Setup
Default Value: ‐
You can configure wireless LAN settings by pressing Enter when "Start"
is displayed.
Wi­Fi Status
Default Value: ‐
The information of the connected access point will be displayed.
"SSID": SSID of the connected access point.
"Signal": Signal strength of the connected access point.
"Status": Status of the connected access point.
MAC Address
Default Value: ‐
This is the MAC address of this unit.
This value is specific to the component and cannot be changed.
DHCP
Default Value: Enable
"Enable": Auto configuration by DHCP
"Disable": Manual configuration without DHCP
If selecting "Disable", you must set "IP Address", "Subnet Mask",
"Gateway", and "DNS Server" manually.
IP Address
Default Value: (0.0.0.0)
Displays/Sets the IP address.
Subnet Mask
Default Value: (0.0.0.0)
Displays/Sets the subnet mask.
Gateway
Default Value: (0.0.0.0)
Displays/Sets the gateway.
DNS Server
Default Value: (0.0.0.0)
Displays/Sets the primary DNS server.
Proxy URL
Default Value: ‐
Displays/Sets the proxy server URL.
Proxy Port
Default Value: (8080)
Displays/Sets the proxy server port number when you enter "Proxy
URL".
Friendly Name
Default Value: Integra DRX­2 XXXXXX
Change the device name for this unit which is shown on other devices
connected to the network to an easily recognized name.
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors and press Enter.
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing Mode on
the remote controller also toggles between upper and lower cases.)
"←" "→": Moves the cursor to the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
Pressing Clear on the remote controller will remove all the input
characters.
3. After inputting, select "OK" with the cursors and press Enter.
The input name will be saved.
AirPlay Password
Default Value:
You can set a password of up to 31 characters so that only registered
users can use AirPlay®.
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors and press Enter.
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing Mode on
the remote controller also toggles between upper and lower cases.)
"←" "→": Moves the cursor to the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
To select whether to mask the password with "*" or display it in
plain text, press Memory on the remote controller.
Pressing Clear on the remote controller will remove all the input
characters.
3. After inputting, select "OK" with the cursors and press Enter.
The input password will be saved.
Usage Data
Default Value: No
As a means of improving the quality of our products and services,
Onkyo may collect information about your usage over the network.
Select "Yes" if you agree to our collecting this information. Select "No" if
you do not want us to collect this information.
You can set this after confirming the Privacy Policy. When you select
"Usage Data" and press Enter, the Privacy Policy is displayed. (The
same screen is displayed once also when setting up the network
connection.) If you agree to the collection of the information, this
setting also becomes "Yes". Note that if you agree to the Privacy
Policy but select "No" for this setting, the information will not be
collected.
Network Check
Default Value: ‐
You can check the network connection.
Press Enter when "Start" is displayed.
Wait for a while if "Network" cannot be selected. It will appear when the
network feature is started.
3. Bluetooth
Bluetooth
Default Value: On
Select whether or not to use the BLUETOOTH function.
"On": Enables connection with a BLUETOOTH enabled device by using
the BLUETOOTH function. Select "On" also when making various
BLUETOOTH settings.
"Off": When not using the BLUETOOTH function
Auto Input Change
Default Value: On
The input of the unit will automatically be switched to "BLUETOOTH"
when connection is made from a BLUETOOTH enabled device to the
unit.
"On": The input will automatically become "BLUETOOTH" when a
BLUETOOTH enabled device is connected.
"Off": The function is disabled.
If the input is not switched automatically, set to "Off" and change the
input manually.
Auto Reconnect
Default Value: On
This function automatically reconnects to the BLUETOOTH enabled
device connected last when you change the input to "BLUETOOTH".
"On": Use this function
"Off": Do not use this function
This may not work with some BLUETOOTH enabled devices.
Pairing Information
Default Value: ‐
You can initialize the pairing information saved on this unit.
Pressing Enter when "Clear" is displayed initializes the pairing
information stored in this unit.
This function does not initialize the pairing information on the
BLUETOOTH enabled device. When pairing the unit again with the
device, be sure to clear the pairing information on the BLUETOOTH
enabled device in advance. For information on how to clear the
pairing information, refer to the BLUETOOTH enabled device's
instruction manual.
Device
Default Value: ‐
Displays the name of the BLUETOOTH enabled device connected to
the unit.
The name is not displayed when "Status" is "Ready" and "Pairing".
Status
Default Value: ‐
Displays the status of the BLUETOOTH enabled device connected to
the unit.
"Ready": Not paired
"Pairing": Paired
"Connected": Successfully connected
Wait for a while if "Bluetooth" cannot be selected. It will appear when the
BLUETOOTH function is started up.
4. Power Management
Sleep Timer
Default Value: Off
Allows the unit to enter standby automatically when the specified time
elapses. Select a value from "30 minutes", "60 minutes", and "90
minutes".
"Off": Does not turn the unit to standby automatically.
Auto Standby
Default Value: On/Off
This setting places the unit on standby automatically after 20 minutes of
inactivity without any video or audio input. (When "USB Power Out at
Standby" or "Network Standby" is on, this becomes the HYBRID
STANDBY mode which reduces the increase in power consumption to a
minimum.)
"On": The unit will automatically enter standby mode ("AUTO STBY" will
light).
"Off": The unit will not automatically enter standby mode.
"Auto Standby" is displayed on the display and TV screen 30
seconds before the Auto Standby comes on.
"Auto Standby" does not work when Zone 2 is active.
Default values vary depending on the regions.
Auto Standby in HDMI Standby Through
Default Value: (Off)
Enable or disable "Auto Standby" while "HDMI Standby Through" is on.
"On": The setting will be enabled.
"Off": The setting will be disabled.
This setting cannot be set to "On" if "Auto Standby" is set to "Off".
USB Power Out at Standby
Default Value: Off
Devices connected to the USB port are supplied with electricity even
when this unit is in standby mode when this function is "On".
When using this feature, power consumption increases even when
the unit is on standby, however, the increase in power consumption
is kept to a minimum by automatically entering the HYBRID
STANDBY mode, where only essential circuits are operating.
Network Standby
Default Value: On/Off
When this feature is turned "On", you can turn on the power of the unit
via the network using an application such as Integra Remote that can
control this unit.
When "Network Standby" is used, the power consumption increases
even when the unit is on standby. However, the increase in power
consumption is kept to a minimum by automatically entering the
HYBRID STANDBY mode, where only the essential circuit is
operating.
"Network Standby", which suppresses power consumption, may be
disabled when the network connection is lost. Use the power button
on the remote controller or main unit to turn the unit on if this
happens.
Bluetooth Wakeup
Default Value: Off
This function wakes up the unit on standby by connecting a
BLUETOOTH enabled device.
"On": Use this function
"Off": Do not use this function
Setting to "On" increases the power consumption even when the unit
is on standby. However, the increase in power consumption is kept
to a minimum by automatically entering the HYBRID STANDBY
mode, where only the essential circuit is operating.
This setting is fixed to "Off" if "Bluetooth" ­ "Auto Input Change" is
set to "Off".
Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be
selected. It will appear when the network feature is started.
5. 12V Trigger A
Set when outputting the control signal (maximum 12 V/100 mA) through the
12V TRIGGER OUT A jack. Different settings can be set for each input
selector. You can enable power link operation when you connect the unit and
the external devices equipped with 12V trigger input jack.
Delay
Default Value: 0 sec
Set after how many seconds the 12V trigger output will occur in
response to the unit's operation. As some devices cause a large current
when they turn on, delay the output if such devices are connected.
Select a value between "0 sec" to "3 sec".
BD/DVD
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BD/DVD" is selected as input for main room.
"Zone 2": Output when "BD/DVD" is selected as input for ZONE2.
"Main/Zone 2": Output when "BD/DVD" is selected as input for main
room or ZONE2.
CBL/SAT
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CBL/SAT" is selected as input for main room.
"Zone 2": Output when "CBL/SAT" is selected as input for ZONE2.
"Main/Zone 2": Output when "CBL/SAT" is selected as input for main
room or ZONE2.
GAME
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "GAME" is selected as input for main room.
"Zone 2": Output when "GAME" is selected as input for ZONE2.
"Main/Zone 2": Output when "GAME" is selected as input for main room
or ZONE2.
STRM BOX
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "STRM BOX" is selected as input for main room.
"Zone 2": Output when "STRM BOX" is selected as input for ZONE2.
"Main/Zone 2": Output when "STRM BOX" is selected as input for main
room or ZONE2.
PC
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PC" is selected as input for main room.
"Zone 2": Output when "PC" is selected as input for ZONE2.
"Main/Zone 2": Output when "PC" is selected as input for main room or
ZONE2.
AUX
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "AUX" is selected as input for main room.
"Zone 2": Output when "AUX" is selected as input for ZONE2.
"Main/Zone 2": Output when "AUX" is selected as input for main room
or ZONE2.
CD
CD
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CD" is selected as input for main room.
"Zone 2": Output when "CD" is selected as input for ZONE2.
"Main/Zone 2": Output when "CD" is selected as input for main room or
ZONE2.
TV
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TV" is selected as input for main room.
"Zone 2": Output when "TV" is selected as input for ZONE2.
"Main/Zone 2": Output when "TV" is selected as input for main room or
ZONE2.
PHONO
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PHONO" is selected as input for main room.
"Zone 2": Output when "PHONO" is selected as input for ZONE2.
"Main/Zone 2": Output when "PHONO" is selected as input for main
room or ZONE2.
TUNER
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TUNER" is selected as input for main room.
"Zone 2": Output when "TUNER" is selected as input for ZONE2.
"Main/Zone 2": Output when "TUNER" is selected as input for main
room or ZONE2.
NET
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "NET" is selected as input for main room.
"Zone 2": Output when "NET" is selected as input for ZONE2.
"Main/Zone 2": Output when "NET" is selected as input for main room
or ZONE2.
BLUETOOTH
BLUETOOTH
Default Value: Main
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BLUETOOTH" is selected as input for main room.
"Zone 2": Output when "BLUETOOTH" is selected as input for ZONE2.
"Main/Zone 2": Output when "BLUETOOTH" is selected as input for
main room or ZONE2.
6. 12V Trigger B
Set when outputting the control signal (maximum 12 V/25 mA) through the
12V TRIGGER OUT B jack. Different settings can be set for each input
selector. You can enable power link operation when you connect the unit and
the external devices equipped with 12V trigger input jack.
Delay
Default Value: 1 sec
Set after how many seconds the 12V trigger output will occur in
response to the unit's operation. As some devices cause a large current
when they turn on, delay the output if such devices are connected.
Select a value between "0 sec" to "3 sec".
BD/DVD
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BD/DVD" is selected as input for main room.
"Zone 2": Output when "BD/DVD" is selected as input for ZONE2.
"Main/Zone 2": Output when "BD/DVD" is selected as input for main
room or ZONE2.
CBL/SAT
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CBL/SAT" is selected as input for main room.
"Zone 2": Output when "CBL/SAT" is selected as input for ZONE2.
"Main/Zone 2": Output when "CBL/SAT" is selected as input for main
room or ZONE2.
GAME
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "GAME" is selected as input for main room.
"Zone 2": Output when "GAME" is selected as input for ZONE2.
"Main/Zone 2": Output when "GAME" is selected as input for main room
or ZONE2.
STRM BOX
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "STRM BOX" is selected as input for main room.
"Zone 2": Output when "STRM BOX" is selected as input for ZONE2.
"Main/Zone 2": Output when "STRM BOX" is selected as input for main
room or ZONE2.
PC
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PC" is selected as input for main room.
"Zone 2": Output when "PC" is selected as input for ZONE2.
"Main/Zone 2": Output when "PC" is selected as input for main room or
ZONE2.
AUX
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "AUX" is selected as input for main room.
"Zone 2": Output when "AUX" is selected as input for ZONE2.
"Main/Zone 2": Output when "AUX" is selected as input for main room
or ZONE2.
CD
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CD" is selected as input for main room.
"Zone 2": Output when "CD" is selected as input for ZONE2.
"Main/Zone 2": Output when "CD" is selected as input for main room or
ZONE2.
TV
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TV" is selected as input for main room.
"Zone 2": Output when "TV" is selected as input for ZONE2.
"Main/Zone 2": Output when "TV" is selected as input for main room or
ZONE2.
PHONO
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PHONO" is selected as input for main room.
"Zone 2": Output when "PHONO" is selected as input for ZONE2.
"Main/Zone 2": Output when "PHONO" is selected as input for main
room or ZONE2.
TUNER
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TUNER" is selected as input for main room.
"Zone 2": Output when "TUNER" is selected as input for ZONE2.
"Main/Zone 2": Output when "TUNER" is selected as input for main
room or ZONE2.
NET
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "NET" is selected as input for main room.
"Zone 2": Output when "NET" is selected as input for ZONE2.
"Main/Zone 2": Output when "NET" is selected as input for main room
or ZONE2.
BLUETOOTH
Default Value: Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BLUETOOTH" is selected as input for main room.
"Zone 2": Output when "BLUETOOTH" is selected as input for ZONE2.
"Main/Zone 2": Output when "BLUETOOTH" is selected as input for
main room or ZONE2.
7. 12V Trigger C
Set when outputting the control signal (maximum 12 V/25 mA) through the
12V TRIGGER OUT C jack. Different settings can be set for each input
selector. You can enable power link operation when you connect the unit and
the external devices equipped with 12V trigger input jack.
Delay
Default Value: 2 sec
Set after how many seconds the 12V trigger output will occur in
response to the unit's operation. As some devices cause a large current
when they turn on, delay the output if such devices are connected.
Select a value between "0 sec" to "3 sec".
BD/DVD
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BD/DVD" is selected as input for main room.
"Zone 2": Output when "BD/DVD" is selected as input for ZONE2.
"Main/Zone 2": Output when "BD/DVD" is selected as input for main
room or ZONE2.
CBL/SAT
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CBL/SAT" is selected as input for main room.
"Zone 2": Output when "CBL/SAT" is selected as input for ZONE2.
"Main/Zone 2": Output when "CBL/SAT" is selected as input for main
room or ZONE2.
GAME
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "GAME" is selected as input for main room.
"Zone 2": Output when "GAME" is selected as input for ZONE2.
"Main/Zone 2": Output when "GAME" is selected as input for main room
or ZONE2.
STRM BOX
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "STRM BOX" is selected as input for main room.
"Zone 2": Output when "STRM BOX" is selected as input for ZONE2.
"Main/Zone 2": Output when "STRM BOX" is selected as input for main
room or ZONE2.
PC
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PC" is selected as input for main room.
"Zone 2": Output when "PC" is selected as input for ZONE2.
"Main/Zone 2": Output when "PC" is selected as input for main room or
ZONE2.
AUX
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "AUX" is selected as input for main room.
"Zone 2": Output when "AUX" is selected as input for ZONE2.
"Main/Zone 2": Output when "AUX" is selected as input for main room
or ZONE2.
CD
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CD" is selected as input for main room.
"Zone 2": Output when "CD" is selected as input for ZONE2.
"Main/Zone 2": Output when "CD" is selected as input for main room or
ZONE2.
TV
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TV" is selected as input for main room.
"Zone 2": Output when "TV" is selected as input for ZONE2.
"Main/Zone 2": Output when "TV" is selected as input for main room or
ZONE2.
PHONO
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PHONO" is selected as input for main room.
"Zone 2": Output when "PHONO" is selected as input for ZONE2.
"Main/Zone 2": Output when "PHONO" is selected as input for main
room or ZONE2.
TUNER
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TUNER" is selected as input for main room.
"Zone 2": Output when "TUNER" is selected as input for ZONE2.
"Main/Zone 2": Output when "TUNER" is selected as input for main
room or ZONE2.
NET
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "NET" is selected as input for main room.
"Zone 2": Output when "NET" is selected as input for ZONE2.
"Main/Zone 2": Output when "NET" is selected as input for main room
or ZONE2.
BLUETOOTH
Default Value: Main/Zone 2
Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BLUETOOTH" is selected as input for main room.
"Zone 2": Output when "BLUETOOTH" is selected as input for ZONE2.
"Main/Zone 2": Output when "BLUETOOTH" is selected as input for
main room or ZONE2.
7. Multi Zone
Make settings related to Multi­zone Connection, such as the volume for the
separate room.
1. Zone 2
Output Level
Default Value: Fixed
Select which of the integrated amplifier in a separate room or this unit
should be used to adjust the volume when Zone 2 is active.
"Fixed": Adjust on the Integrated amplifier in a separate room
"Variable": Adjust on the unit
Maximum Volume
Default Value: Off
Set the maximum value for Zone 2 to avoid too high volume. Select a
value from "Off", "50" to "99".
Power On Volume
Default Value: Last
Set the Zone 2 volume level of when this unit is turned on. Select a
value from "Last" (Volume level when the unit was turned off), "Min", "1"
to "99" and "Max".
You cannot set a higher value than that of "Maximum Volume".
8. Miscellaneous
Change the frequency step for the tuner, update the firmware, and perform
Initial Setup, etc.
1. Tuner
AM / FM Frequency Step (North American models)
Default Value: 10 kHz / 0.2 MHz
Select a frequency step depending on your area of residence.
Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz".
When this setting is changed, all radio presets are deleted.
AM Frequency Step (Australian models)
Default Value: 9 kHz
Select a frequency step depending on your area of residence.
Select "10 kHz" or "9 kHz".
When this setting is changed, all radio presets are deleted.
2. Remote ID
Remote ID
Default Value: 1
Select an ID for the unit's remote controller from "1", "2", and "3" to
prevent interference between the unit and other Integra/ONKYO
components that are installed in the same room. After changing the ID
on the main unit, change the ID on the remote controller accordingly
with the following procedure.
While holding down Mode, press the following buttons for about 3
seconds.
To change the remote controller ID to "1":
(The remote indicator flashes once.)
To change the remote controller ID to "2":
(The remote indicator flashes twice.)
To change the remote controller ID to "3":
(The remote indicator flashes three times.)
3. Firmware Update
Update Notice
Default Value: Enable
Availability of a firmware update will be notified via network.
"Enable": Notify updates
"Disable": Do not notify updates
Version
Default Value: ‐
The current firmware version will be displayed.
Update via NET
Default Value: ‐
Press Enter to select when you want to update the firmware via
network.
You will not be able to select this setting if you do not have
Internet access or there is nothing to update.
Update via USB
Default Value: ‐
Press Enter to select when you want to update the firmware via USB.
You will not be able to select this setting if a USB storage device
is not connected or there is nothing to update in the USB storage
device.
Wait for a while if "Firmware Update" cannot be selected. It will appear
when the network feature is started.
4. Initial Setup
You can make the initial setup from the setup menu.
Wait for a while if "Initial Setup" cannot be selected. It will appear when
the network feature is started.
5. Lock
Setup Parameter
Default Value: Unlocked
Lock the Setup menu to protect the settings.
"Locked": The menu is locked.
"Unlocked": The menu is unlocked.
Settings
Initial Setup
When you turn the unit on for the first time after purchasing it, Initial Setup is
automatically shown on the TV to enable you to make settings required for
startup using simple operations following onscreen guidance.
Operation:
Select the item with the cursors of the remote controller and press Enter to
confirm your selection. To return to the previous screen, press .
To redo Initial Setup:
If you terminate the procedure on the way or want to change a setting made
during Initial Setup, press
on the remote controller, select "8.
Miscellaneous" ­ "Initial Setup", and press Enter.
1. AccuEQ Room Calibration
Place the supplied speaker setup microphone in the listening position,
measure the test tones emitted by the speakers, then the unit automatically
sets the optimum volume level for each speaker, the crossover frequencies,
and the distance from the listening position. This also automatically adjusts
the equalizers for the speakers and enables correction of distortion caused
by the acoustic environment of the room.
Calibration takes several minutes to be completed. The speakers emit the
test tone at high volume during measurement, so be careful of your
surroundings. Keep the room as quiet as possible during measurement. If
the measurement is interrupted, turn off the household appliances.
1. Place the supplied speaker setup microphone in the listening position,
and connect to the Setup Mic jack on the main unit.
When putting the speaker setup microphone on a tripod, refer to the
illustration when putting it in place.
2. Select the connected speaker configuration.
The image on the screen changes as you choose the number of channels
in "Speaker Channels", so refer to it when performing the settings. Select
5.1.2ch, etc., when using a height speaker.
Also use this screen to select whether you have connected a subwoofer
and to select the type of height speaker, etc.
If you have connected a subwoofer, check the power and volume of
the subwoofer. The low frequencies played by the subwoofer may not
be discernible, so set its volume to at least halfway.
3. Test tones are emitted by the speakers, and firstly the unit detects the
speakers connected and the noise in the environment.
4. After the results of the above measurements are displayed, select "Next",
press Enter on the remote controller, and the test tones are emitted
again, and the unit automatically makes settings such as the optimum
volume level and the crossover frequency.
5. When the measurement is completed, the measurement result is
displayed.
Press the cursors / on the remote controller to check the settings.
Press Enter when "Save" is selected to save the settings.
6. Select whether to enable or disable the equalizer function that corrects for
distortion caused by the acoustic environment of the room.
If this is to be enabled, then normally you should select "On (All
Channels)", and to disable just the front speakers you should select "On
(Except Front Left / Right)".
7. Disconnect the speaker setup microphone.
2. Source Connection
Check that each input source is connected correctly. Follow the guidance,
select the input you want to confirm, start play of the selected player, and
confirm that the images appear on the TV and that sound is played.
3. Network Connection
Set up Wi­Fi connection with an access point such as a wireless LAN router.
There are the following two methods of connecting by Wi­Fi:
"Scan Networks": Search for an access point from this unit. Find out the
SSID of the access point beforehand.
"Use iOS Device (iOS7 or later)": Share the iOS device's Wi­Fi settings
with this unit.
If you select "Scan Networks", there are a further two choices of connection
method. Check the following.
"Enter Password": Enter the password (or key) of the access point to
connect.
"Push Button": If the access point has an automatic connection button, you
can connect without entering a password.
If the SSID of the access point is not displayed, then in the screen listing
the SSIDs, select "Other..." with the cursor on the remote controller and
press Enter, then follow the onscreen instructions.
Keyboard input
To switch between upper and lower case, select "A/a" on the screen and
press Enter. To select whether to mask the password with "*" or display it in
plain text, press Memory on the remote controller. Pressing Clear will delete
all the input characters.
A confirmation screen asking you to agree to the privacy policy is
displayed during network setting. Select "Yes" and press Enter to indicate
agreement.
4. Multi Zone Setup
When you want to enjoy audio in a room other than the main room, set the
audio output method for the separate room (ZONE 2). If you have connected
speakers in a separate room with speaker cable, select "Using AV Receiver".
If you have connected a pre­main amplifier in a separate room with an
analog audio cable, select "with External Premain Amplifier". If you have
connected a power amplifier, select "with External Power Amplifier".
5. Audio Return Channel
If you have connected a TV that supports ARC, select "Yes". This unit's ARC
setting turns on and you can listen to the TV's audio through this unit.
Settings
Quick Menu
You can quickly adjust settings you frequently use, such as tone
adjustments, etc.
Operation:
You can make the settings on the TV screen while playing something. Press
Q on the remote controller to display the Quick Menu.
Select the item with the cursor / buttons of the remote controller and
press Enter to confirm your selection.
Use the cursors to change the settings.
To return to the previous screen, press .
To exit the settings, press Q.
Tone
Bass:
Enhance or moderate the bass range of the front speakers.
Treble:
Enhance or moderate the treble range of the front speakers.
It cannot be set if the listening mode is Direct.
Level
Center:
Adjust the speaker level of the center speaker while listening to some sound.
Subwoofer:
Adjust the speaker level of the subwoofer while listening to some sound.
The adjustment you made will be reset to the previous status when you
turn the unit to standby mode.
AccuEQ
AccuEQ Room Calibration:
Enable or disable the equalizer function that corrects for distortion caused by
the acoustic environment of the room. If this is to be enabled, then normally
you should select "On (All Ch)", and to disable just the front speakers you
should select "On (ex. L/R)". The setting can be separately set to each input
selector.
Equalizer:
Select "Preset 1" to "Preset 3" configured in "2. Speaker" ­ "Equalizer
Settings" in the Setup menu. The same sound field setting is applied all
ranges when set to "Off".
Cinema Filter:
Adjust the soundtrack that was processed to enhance its high pitch range, in
order to make it suitable for home theater. This function can be used in the
following listening modes: Dolby Digital, Dolby Digital Plus, Dolby Surround,
Dolby TrueHD, Multichannel, DTS, DTS­ES, DTS 96/24, DTS­HD High
Resolution Audio, DTS­HD Master Audio, DTS Neural:X, DTS Express,
Neo:6 Cinema, and DSD.
It cannot be set if the listening mode is Direct.
Other
A/V Sync :
If the video is behind the audio, you can delay the audio to offset the gap.
Different settings can be set for each input selector.
It cannot be set if the listening mode is Direct.
Music Optimizer:
Improve the quality of the compressed audio. Playback sound of lossy
compressed files such as MP3 will be improved. The setting can be
separately set to each input selector. The setting is effective in the signals of
48 kHz or less. The setting is not effective in the bitstream signals.
It cannot be set if the listening mode is Direct.
Late Night:
Make small sounds easily heard. It is useful when you need to reduce the
volume while watching a movie late night. You can enjoy the effect only
when playing Dolby series and DTS series input signals.
The setting cannot be used in the following cases.
– If "Loudness Management" is set to "Off" when playing Dolby Digital
Plus or Dolby TrueHD
– When the input signal is DTS and "Dialog Control" is other than 0 dB
Center Spread:
Adjust the width of the sound field of the front channel when playing in the
Dolby Surround listening mode. To spread the width of the sound field to the
left and right, set to "On". To concentrate sound in the center, set to "Off".
Depending on the speaker settings, this becomes "Off".
Dialog Control:
You can increase the dialog portion of the audio in 1 dB steps up to 6 dB so
that you can make dialog easier to hear over background noise.
This cannot be set for content other than DTS:X.
We plan to provide support for the DTS:X audio format through a
firmware update for this unit. Center Image is displayed until the update.
The effect may not be selectable with some content.
Settings
Control Function Settings
You can enable the control functions between the unit and external devices.
Special devices or cable connections are necessary to enable the functions.
For more information about installation, contact a store specializing in these
products.
RS232 port
Use this port for connection with an integrated control system that can
enable home automation. Some integrated control systems provide a
centralized operation with a single touch panel controller in order to control
audio and video home appliances and security devices together. For more
information about adopting an integrated control system, contact the
specialized stores.
IR jack
If you use a commercially available multiroom remote control kit with this
jack, you can operate the unit with the remote controller even when you are
in a separate room, or operate the unit with the remote controller even if its
remote control sensor is difficult to see. You can also connect a device with
the unit and operate it with the remote controller.
Other companies may use indications other than IR on their products.
Confirm in the instruction manual included with your components.
Refer to the instruction manual of the IR receiver for the types of cables
required for connection.
12V trigger output jack
You can enable power link operation when you connect the unit and an
external device such as power amplifier equipped with 12V trigger input jack.
When the desired input is selected on the unit, power link operation will be
activated with a control signal of maximum 12 V/100 mA from the 12V
TRIGGER OUT A jack or maximum 12 V/25 mA when using the 12V
TRIGGER OUT B or C jack. You can select the zone to output the control
signal by setting each of the inputs. For connection, use a monaural mini
plug cable.
Settings
Firmware Update
About Firmware Update
There are two methods for updating the firmware: via network and via USB.
Use the one that best suits your environment.
For the latest information on updates, visit our company's website. There
is no need to update the firmware on this unit if there is no update
available.
Before updating, make sure that the speaker setup microphone is not
connected.
During an update, do not
– Disconnect and reconnect any cable, USB storage device, speaker
setup microphone or headphones, or perform any operation on the
component such as turn off its power
– Accessing this unit from a PC or smartphone using an application
The update may take about 20 minutes to complete for either method: via
network or via USB. Furthermore, existing settings are guaranteed
regardless of the method used for update.
Note that when this unit is connected to a network, you may see notifications
about firmware updates on the display. To execute updating, select "Update
Now" with the cursor buttons of the remote controller and press Enter. The
unit automatically turns itself into standby mode after "Completed!" appears
on the display, and updating will be complete.
Disclaimer: The program and accompanying online documentation are
furnished to you for use at your own risk.
Our company will not be liable and you will have no remedy for damages for
any claim of any kind whatsoever concerning your use of the program or the
accompanying online documentation, regardless of legal theory, and whether
arising in tort or contract.
In no event will our company be liable to you or any third party for any
special, indirect, incidental, or consequential damages of any kind, including,
but not limited to, compensation, reimbursement or damages on account of
the loss of present or prospective profits, loss of data, or for any other
reason whatsoever.
Settings
Firmware Update
Updating the Firmware via Network
Preparation:
Check that the unit is turned on, and the connection to the Internet is
secured.
Turn off the controller component (PC etc.) connected to the network.
Stop any playing Internet radio, USB storage device, or server content.
If the multi­zone function is active, turn it off.
If "HDMI CEC" is set to "On", set it to "Off".
– Press
on the remote controller. Then, after selecting "6. Hardware"
­ "HDMI" and pressing Enter, select "HDMI CEC" and select "Off".
* The description may differ from the on­screen display but that will not
change the way to operate or the function.
Update
1. Press
on the remote controller.
The Setup menu is displayed on the TV screen.
2. Select "8. Miscellaneous" ­ "Firmware Update" ­ "Update via NET" with
the cursors in order, then press Enter.
If "Firmware Update" is grayed out and cannot be selected, wait for a
while until it starts up.
You will not be able to select "Update via NET" if there is nothing to
update.
3. Press Enter with "Update" selected to start update.
During the update, the TV screen may go black depending on the
updated program. In that case, check the progress on the display of
the unit. The TV screen will remain black until the update is complete
and the power is turned on again.
"Completed!" is displayed when the update is complete.
4. Press On/Standby on the main unit to turn the unit into standby mode.
The process is completed and your firmware is updated to the latest
version.
Do not use on the remote controller.
If an Error Message is Displayed
When an error occurs, "*­** Error!" is displayed on the display of the unit.
("*" represents an alphanumeric character.) Check the following:
Error Code
*­01, *­10:
Ethernet cable not found. Connect the Ethernet cable properly.
*­02, *­03, *­04, *­05, *­06, *­11, *­13, *­14, *­16, *­17,
*­18, *­20, *­21:
Internet connection error. Check the following:
– The router is turned on
– This unit and the router are connected via the network
Try to disconnect and then connect again the power to the unit and router.
This may solve the problem. If you are still unable to connect to the
Internet, the DNS server or proxy server may be temporarily down. Check
the service status with your ISP provider.
Others
Disconnect then reconnect the AC power cord, then repeat from the
beginning.
Settings
Firmware Update
Updating via USB
Preparation:
Prepare a 128MB or larger USB storage device. FAT16 or FAT32 file
system format.
– Media inserted in a USB card reader may not be used for this function.
– USB storage devices with security function are not supported.
– USB hubs and USB devices with hub function are not supported. Do
not connect these devices to the unit.
Delete any data stored on the USB storage device.
Turn off the controller component (PC etc.) connected to the network.
Stop any playing Internet radio, USB storage device, or server content.
If the multi­zone function is active, turn it off.
If "HDMI CEC" is set to "On", set it to "Off".
– Press
on the remote controller. Then, after selecting "6. Hardware"
­ "HDMI" and pressing Enter, select "HDMI CEC" and select "Off".
* Some USB storage devices may take long to load, may not be loaded
correctly, or may not be correctly fed depending on the device or their
content.
* Our company will not be liable whatsoever for any loss or damage of
data, or storage failure arising from the use of the USB storage device
with this unit. Thank you for your understanding.
* The description may differ from the on­screen display but that will not
change the way to operate or the function.
Update
1. Connect the USB storage device to your PC.
2. Download the firmware file from our company's website to your PC and
unzip.
Firmware files are named in the following way:
ONKAVR****_************.zip
Unzip the file on your PC. The number of unzipped files and folders
varies depending on the model.
3. Copy all unzipped files and folders to the root folder of the USB storage
device.
Make sure to copy the unzipped files.
4. Connect the USB storage device to the USB port of the unit.
If you connect a USB hard disk drive to the USB port of the unit, we
recommend that you use its AC adapter to power it.
If the USB storage device has been partitioned, each section will be
treated as an independent device.
5. Press
on the remote controller.
The Setup menu is displayed on the TV screen.
6. Select "8. Miscellaneous" ­ "Firmware Update" ­ "Update via USB" with
the cursors in order, then press Enter.
If "Firmware Update" is grayed out and cannot be selected, wait for a
while until it starts up.
You will not be able to select "Update via USB" if there is nothing to
update.
7. Press Enter with "Update" selected to start update.
During the update, the TV screen may go black depending on the
updated program. In that case, check the progress on the display of
the unit. The TV screen will remain black until the update is complete
and the power is turned on again.
During the update, do not turn off, or disconnect then reconnect the
USB storage device.
"Completed!" is displayed when the update is complete.
8. Disconnect the USB storage device from the unit.
9. Press On/Standby on the main unit to turn the unit into standby mode.
The process is completed and your firmware is updated to the latest
version.
Do not use
on the remote controller.
If an Error Message is Displayed
When an error occurs, "*­** Error!" is displayed on the display of the unit.
("*" represents an alphanumeric character.) Check the following:
Error Code
*­01, *­10:
USB storage device not found. Check whether the USB storage device or
USB cable is correctly inserted to the USB port of the unit.
Connect the USB storage device to an external power source if it has its
own power supply.
*­05, *­13, *­20, *­21:
The firmware file is not present in the root folder of the USB storage
device, or the firmware file is for another model. Retry from the download
of the firmware file.
Others
Disconnect then reconnect the AC power cord, then repeat from the
beginning.
Listening Modes
Selecting Listening Modes
Select the optimum listening mode for movies, TV, music, and games by
repeatedly pressing the Movie/TV, Music, and Game buttons.
1. During play, press one of the following three buttons on the remote
controller.
2. Press the selected button repeatedly to switch the modes displayed on
the display of the unit.
For details on the effects of each of the listening modes see "Listening Mode
Effects". For listening modes selectable for each of the audio formats in the
input signals, refer to "Selectable Listening Modes".
Listening Modes
Listening Mode Effects
Updating of listening modes
We plan to provide support for the DTS:X audio format through firmware
updates for this unit. This means that the selectable listening modes depend
on the version of firmware.
On firmware version before DTS:X support
You can select Neo:6 Cinema and Neo:6 Music.
On firmware version after DTS:X support
You can select DTS:X and DTS Neural:X. (You cannot select Neo:6
Cinema and Neo:6 Music after updating.)
In alphabetical order
AllCh Stereo
Ideal for background music, this mode fills the entire listening area with
stereo sound from the front, surround, and surround back speakers.
Direct
This listening mode can be selected for all input signals. Processing that
affects sound quality is shut down so sound closer to the original is
reproduced. Speakers play the sound field according to the number of
channels in the input signal, so there would be output from only the front
speakers for a two­channel signal, for example.
Dolby Atmos
This mode faithfully reproduces the sound design recorded in the Dolby
Atmos audio format.
The Dolby Atmos audio format has been implemented in movie theaters
equipped with the latest facilities and enables a revolutionary sound
experience in home theaters. Unlike existing surround systems, Dolby Atmos
doesn't rely on channels, but rather enables the accurate placement of
sound objects that have independent motion in a three­dimensional space
with even greater clarity. Dolby Atmos is an optional audio format on Blu­ray
Discs and achieves a three­dimensional sound field by introducing a sound
field above the listener.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
Dolby D (Dolby Digital)
This mode faithfully reproduces the sound design recorded in the Dolby
Digital audio format.
Dolby Digital is a multi­channel digital format developed by Dolby
Laboratories, Inc. widely adopted for use in movie production. It is also a
standard audio format on DVD­Video and Blu­ray Discs. It is possible to
record a maximum of 5.1 channels on a DVD­Video or Blu­ray Disc; two front
channels, a center channel, two surround channels, and the LFE channel
dedicated to the bass region (sound elements for the subwoofer).
To enable transfer of this audio format, connect via digital cable and set
audio output on the player to bitstream output.
Dolby D+ (Dolby Digital Plus)
This mode faithfully reproduces the sound design recorded in the Dolby
Digital Plus audio format.
The Dolby Digital Plus format is a revision based on Dolby Digital, increasing
the number of channels and endeavoring to improve sound quality by giving
more flexibility in data bit rates. Dolby Digital Plus is used as an optional
audio format on Blu­ray Discs, based on 5.1ch, but with additional channels
such as the surround back channel added for a maximum of 7.1ch.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
Dolby Surround
These listening modes allow you to expand the playback signal to 5.1
channels or 7.1 channels to suit the connected speaker configuration when
the input signal is 2 channels or 5.1 channels. Dolby surround is a next
generation surround technology that intelligently up mixes stereo; 5.1 and
7.1 content for playback through your surround speaker system. Dolby
surround is compatible with traditional speaker layouts, as well as Dolby
Atmos enabled playback systems that employ inceiling speakers or products
with Dolby speaker technology.
Dolby TrueHD
This mode faithfully reproduces the sound design recorded in the Dolby
TrueHD audio format.
The Dolby TrueHD audio format is a reversible format expanded based on
the lossless compression technology referred to as MLP, and it makes it
possible to faithfully reproduce the master audio recorded in the studio.
Dolby TrueHD is used as an optional audio format on Blu­ray Discs, based
on 5.1ch, but with additional channels such as the surround back channel
added for a maximum of 7.1ch. 7.1ch is recorded at 96 kHz/24bit, and 5.1ch
is recorded at 192 kHz/24bit.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
DSD
Mode suitable for playing sources recorded in DSD.
This unit supports DSD signals input through HDMI IN. However,
depending on the connected player, better sound is possible when output
from the PCM output of the player.
This listening mode cannot be selected if the output setting on your Blu­
ray Disc/DVD player is not set to DSD.
DTS
This mode faithfully reproduces the sound design recorded in the DTS audio
format.
The DTS audio format is a multi­channel digital format developed by DTS,
Inc. This format is an optional audio format on DVD­Video and a standard on
Blu­ray Discs. It enables recording of 5.1 channels; two front channels, a
center channel, two surround channels, and the LFE channel dedicated to
the bass region (sound elements for the subwoofer). The content is recorded
with a rich volume of data, with maximum sampling rate of 48 kHz at a
resolution of 24 bits and a bit rate of 1.5 Mbps.
To enable transfer of this audio format, connect via digital cable and set
audio output on the player to bitstream output.
DTS 96/24
This mode faithfully reproduces the sound design recorded in the DTS 96/24
audio format.
The DTS 96/24 format is an optional audio format on DVD­Video and Blu­ray
Discs. It enables recording of 5.1 channels; two front channels, a center
channel, two surround channels, and the LFE channel dedicated to the bass
region (sound elements for the subwoofer). Detailed reproduction is
achieved by recording the content at a sampling rate of 96 kHz at a
resolution of 24 bits.
To enable transfer of this audio format, connect via digital cable and set
audio output on the player to bitstream output.
DTS Express
This mode faithfully reproduces the sound design recorded in the DTS
Express audio format.
DTS Express is used as an optional audio format on Blu­ray Discs, based on
5.1ch, but with channels such as the surround back channel added for a
maximum of 7.1ch. It also supports low bit rates.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
DTS­HD HR (DTS­HD High Resolution Audio)
This mode faithfully reproduces the sound design recorded in the DTS­HD
High Resolution Audio audio format.
DTS­HD High Resolution Audio is used as an optional audio format on Blu­
ray Discs, based on 5.1ch, but with additional channels such as the surround
back channel added for a maximum of 7.1ch. It can be recorded at a
sampling rate of 96 kHz with a resolution of 24 bits.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
DTS­HD MSTR (DTS­HD Master Audio)
This mode faithfully reproduces the sound design recorded in the DTS­HD
Master Audio audio format.
DTS­HD Master Audio is used as an optional audio format on Blu­ray Discs,
based on 5.1ch, but with additional channels such as the surround back
channel added for a maximum of 7.1ch, recorded using lossless audio
reproduction technology. 96 kHz/24bit is supported with 7.1ch, and
192 kHz/24bit is supported with 5.1ch.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
DTS Neo:6
These listening modes allow you to expand the playback signal to 5.1
channels or 7.1 channels to suit the connected speaker configuration when
the input signal is 2 channel. It offers full­bandwidth on all channels, with
great independence between the channels. There are two variants for this
mode: Neo:6 Cinema which is ideal for movies and Neo:6 Music which is
ideal for music.
DTS Neural:X
This listening mode allows you to expand the playback signal to 5.1
channels or 7.1 channels to suit the connected speaker configuration when
the input signal is 2 channels or 5.1 channels. Neural:X enables upmixing of
legacy content such as mono, stereo, 5.1 or 7.1ch to many higher speaker
count including the layout using elevated channels set for DTS:X playback.
DTS:X
This mode faithfully reproduces the sound design recorded in the DTS:X
audio format.
The DTS:X audio format is a combination of the mixing methodology based
on past channel based formats (5.1ch and 7.1ch) and object based dynamic
audio mixing, and it is characterized by the precise positioning of sounds and
the ability to express movement. DTS:X is DTS's next­generation object­
based surround sound technology that includes height to deliver a fully­
immersive listening experience to your living room.
To enable transfer of this audio format, connect via HDMI cable and set
audio output on the player to bitstream output.
ES Discrete (DTS­ES Discrete)
This mode faithfully reproduces the sound design recorded in the DTS­ES
Discrete audio format.
DTS­ES Discrete is used as an optional audio format on DVD­Video and Blu­
ray Discs, based on 5.1ch, but with an additional monaural surround back
channel added for a maximum of 6.1ch.
To enable transfer of this audio format, connect via digital cable and set
audio output on the player to bitstream output.
ES Matrix (DTS­ES Matrix)
This mode faithfully reproduces the sound design recorded in the DTS­ES
Matrix audio format.
DTS­ES Matrix is used as an optional audio format on DVD­Video and Blu­
ray Discs, based on 5.1ch, but with a monaural surround back channel
included by matrix encoding. The matrix decoder on this unit decodes this
during playback to produce 6.1 channels.
To enable transfer of this audio format, connect via digital cable and set
audio output on the player to bitstream output.
Full Mono
In this mode, all speakers output the same sound in mono, so the sound you
hear is the same regardless of where you are within the listening room.
Game­Action
In this mode, sound localization is distinct with emphasis on bass.
Game­Rock
In this mode, sound pressure is emphasized to heighten live feel.
Game­RPG
In this mode, the sound has a dramatic feel with a similar atmosphere to
Orchestra mode.
Game­Sports
Suitable for audio source with much reverberation.
Mono
Use this mode when watching an old movie with a mono soundtrack, or use
it to separately reproduce soundtracks in two different languages recorded in
the left and right channels of some movies. It is also suitable for DVDs or
other sources containing multiplexed audio.
Multich (Multichannel)
Mode suitable for playing sources recorded in multichannel PCM.
Orchestra
Suitable for classical or operatic music. This mode emphasizes the surround
channels in order to widen the stereo image, and simulates the natural
reverberation of a large hall.
Stereo
In this mode, sound is output from the front left and right speakers and
subwoofer.
Studio­Mix
Suitable for rock or pop music. Listening to music in this mode creates a
lively sound field with a powerful acoustic image, like being at a club or rock
concert.
T­D (Theater­Dimensional)
In this mode, you can enjoy a virtual playback of multichannel surround
sound even with only two or three speakers. This works by controlling how
sounds reach the listener's left and right ears.
TV Logic
Suitable for TV shows produced in a TV studio. This mode enhances the
surround effects to the entire sound to give clarity to voices and create a
realistic acoustic image.
Unplugged
Suitable for acoustic instruments, vocals and jazz. This mode emphasizes
the front stereo image, giving the impression of being right in front of the
stage.
Listening Modes
Selectable Listening Modes
You can select a variety of listening modes to suit the audio format of the
signal being input. Refer to the following for the listening mode choices.
Listening modes available when headphones are connected are: Mono,
Direct, and Stereo.
Updating of listening modes
We plan to provide support for the DTS:X audio format through firmware
updates for this unit. This means that the selectable listening modes depend
on the version of firmware.
On firmware version before DTS:X support
You can select Neo:6 Cinema and Neo:6 Music.
On firmware version after DTS:X support
You can select DTS:X and DTS Neural:X. (You cannot select Neo:6
Cinema and Neo:6 Music after updating.)
Movie/TV button
This is a list of listening modes you can select according to the audio format
of the input signal.
Input Format
Analog
Direct
Mono
Dolby Surround
Neo:6 Cinema*1
DTS Neural:X
TV Logic*2
AllCh Stereo*3
Full Mono*3
T­D
*1
A center speaker or surround speakers need to be installed.
*2
*3
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
PCM
Music files (except DSD/Dolby TrueHD)
Direct
Mono
Dolby Surround
Neo:6 Cinema*1
DTS Neural:X
TV Logic*2
AllCh Stereo*3
Full Mono*3
T­D
*1
*2
*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Multich PCM
Direct
Multich*1
Dolby Surround
DTS Neural:X
TV Logic*2
AllCh Stereo*3
Full Mono*3
T­D
*1
*2
*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DSD
Direct
DSD*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is monaural or 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby Atmos
You can select the Dolby Digital Plus or Dolby TrueHD listening
modes if a surround back speaker or height speaker is not
connected.
Direct
Dolby Atmos
TV Logic
AllCh Stereo
Full Mono
T­D
Dolby D
Direct
Dolby D*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
*5
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby D+
Direct
Dolby D+*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby TrueHD
Direct
Dolby TrueHD*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS
Direct
DTS*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS 96/24
Direct
DTS 96/24*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS Express
Direct
DTS Express*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­HD HR
Direct
DTS­HD HR*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­HD MSTR
Direct
DTS­HD MSTR*1 *2
Dolby Surround
Neo:6 Cinema*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­ES
Direct
DTS*1
ES Matrix*2
ES Discrete*2
Dolby Surround*3
DTS Neural:X
TV Logic*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
This can only be selected when no surround back speaker is
connected.
Surround back speakers need to be installed.
Height speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS:X
Direct
DTS:X
TV Logic*1
AllCh Stereo*2
Full Mono*2
T­D
*1
*2
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Music button
This is a list of listening modes you can select according to the audio format
of the input signal.
Input Format
Analog
Direct
Stereo
Dolby Surround
Neo:6 Music*1
DTS Neural:X
Orchestra*2
Unplugged*2
Studio­Mix*2
AllCh Stereo*3
Full Mono*3
*1
*2
*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
PCM
Music files (except DSD/Dolby TrueHD)
Direct
Stereo
Dolby Surround
Neo:6 Music*1
DTS Neural:X
Orchestra*2
Unplugged*2
Studio­Mix*2
AllCh Stereo*3
Full Mono*3
*1
*2
*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Multich PCM
Direct
Stereo
Multich*1
Dolby Surround
DTS Neural:X
Orchestra*2
Unplugged*2
Studio­Mix*2
AllCh Stereo*3
Full Mono*3
*1
*2
*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DSD
Direct
Stereo
DSD*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
Cannot be selected when the input format is monaural or 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
*4
*5
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby Atmos
You can select the Dolby Digital Plus or Dolby TrueHD listening
modes if a surround back speaker or height speaker is not
connected.
Direct
Stereo
Dolby Atmos
Orchestra
Unplugged
Studio­Mix
AllCh Stereo
Full Mono
Dolby D
Direct
Stereo
Dolby D*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby D+
Direct
Stereo
Dolby D+*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby TrueHD
Direct
Stereo
Dolby TrueHD*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS
Direct
Stereo
DTS*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS 96/24
Direct
Stereo
DTS 96/24*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS Express
Direct
Stereo
DTS Express*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­HD HR
Direct
Stereo
DTS­HD HR*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­HD MSTR
Direct
Stereo
DTS­HD MSTR*1 *2
Dolby Surround
Neo:6 Music*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
*3
*4
*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a center
speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­ES
Direct
Stereo
DTS*1
ES Matrix*2
ES Discrete*2
Dolby Surround*3
DTS Neural:X
Orchestra*4
Unplugged*4
Studio­Mix*4
AllCh Stereo*5
Full Mono*5
*1
*2
This can only be selected when no surround back speaker is
connected.
Surround back speakers need to be installed.
*3
*4
*5
Height speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS:X
Direct
Stereo
DTS:X
Orchestra*1
Unplugged*1
Studio­Mix*1
AllCh Stereo*2
Full Mono*2
*1
*2
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Game button
This is a list of listening modes you can select according to the audio format
of the input signal.
Input Format
Analog
Direct
Dolby Surround
DTS Neural:X
Game­RPG*1
Game­Action*1
Game­Rock*1
Game­Sports*1
AllCh Stereo*2
Full Mono*2
T­D
*1
*2
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
PCM
Music files (except DSD/Dolby TrueHD)
Direct
Dolby Surround
DTS Neural:X
Game­RPG*1
Game­Action*1
Game­Rock*1
Game­Sports*1
AllCh Stereo*2
Full Mono*2
T­D
*1
*2
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Multich PCM
Direct
Multich*1
Dolby Surround
DTS Neural:X
Game­RPG*2
Game­Action*2
Game­Rock*2
Game­Sports*2
AllCh Stereo*3
Full Mono*3
T­D
*1
*2
*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DSD
Direct
DSD*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is monaural or 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby Atmos
You can select the Dolby Digital Plus or Dolby TrueHD listening
modes if a surround back speaker or height speaker is not
connected.
Direct
Dolby Atmos
Game­RPG
Game­Action
Game­Rock
Game­Sports
AllCh Stereo
Full Mono
T­D
Dolby D
Direct
Dolby D*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby D+
Direct
Dolby D+*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Dolby TrueHD
Direct
Dolby TrueHD*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
*3
*4
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS
Direct
DTS*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS 96/24
Direct
DTS 96/24*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS Express
Direct
DTS Express*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­HD HR
Direct
DTS­HD HR*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­HD MSTR
Direct
DTS­HD MSTR*1 *2
Dolby Surround
DTS Neural:X
Game­RPG*3
Game­Action*3
Game­Rock*3
Game­Sports*3
AllCh Stereo*4
Full Mono*4
T­D
*1
*2
*3
*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS­ES
Direct
DTS*1
ES Matrix*2
ES Discrete*2
Dolby Surround*3
DTS Neural:X
Game­RPG*4
Game­Action*4
Game­Rock*4
Game­Sports*4
AllCh Stereo*5
Full Mono*5
T­D
*1
*2
*3
*4
*5
This can only be selected when no surround back speaker is
connected.
Surround back speakers need to be installed.
Height speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
DTS:X
Direct
DTS:X
Game­RPG*1
Game­Action*1
Game­Rock*1
Game­Sports*1
AllCh Stereo*2
Full Mono*2
T­D
*1
*2
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers need to be
installed.
Playback Function
AM/FM radio
Tuning into a Radio Station
Tuning Automatically
1. Press Tuner on the remote controller several times to select either "AM"
or "FM".
2. Press Mode on the remote controller so that "TunMode:Auto" appears on
the display.
3. Press the cursors / on the remote controller to start automatic tuning.
Searching automatically stops when a station is found. When tuned
into a radio station, the "TUNED" indicator on the display lights. When
tuned into an FM radio station, the "FM ST" indicator lights.
No sound is output while the "TUNED" indicator is off.
When FM broadcasts reception is poor:
Radio waves may be weak depending on the building structure and
environmental conditions. In that case, perform the procedure as explained
below in "Tuning Manually" to manually select the desired station.
Tuning Manually
1. Press Tuner on the remote controller several times to select either "AM"
or "FM".
2. Press Mode on the remote controller so that "TunMode:Manual" appears
on the display.
3. While pressing the cursors / on the remote controller, select the
desired radio station.
The frequency changes by 1 step each time you press the button. The
frequency changes continuously if the button is held down and stops
when the button is released. Tune by looking at the display.
To return to the auto tuning mode:
Press Mode on the remote controller again so that "TunMode:Auto" appears
on the display. The unit tunes automatically into a radio station.
Playback Function
AM/FM radio
Presetting a Radio Station
It allows you to register up to 40 of your favorite AM/FM radio stations.
Registering radio stations in advance allows you to tune into your radio
station of choice directly.
Registration Procedure
1. Tune into the AM/FM radio station you want to register.
2. Press Memory on the remote controller so that the preset number on the
display flashes.
3. While the preset number is flashing (about 8 seconds), repeatedly press
/ on the remote controller to select a number between 1 and 40.
4. Press Memory on the remote controller again to register the station.
When the station is registered, the preset number stops flashing.
Repeat this procedure for all of your favorite AM/FM radio stations.
Selecting a Preset Radio Station
1. Press Tuner on the remote controller.
2. Press
/
on the remote controller to select a preset number.
Deleting a Preset Radio Station
1. Press Tuner on the remote controller.
2. Press
/
on the remote controller to select the preset number to delete.
3. After pressing Memory on the remote controller, press Clear while the
preset number is flashing to delete the preset number.
When deleted, the number on the display goes off.
Playback Function
AM/FM radio
Using RDS (Australian models)
RDS stands for Radio Data System and is a method of transmitting data in
FM radio signals. In regions using RDS, the radio station name is displayed
when you tune into a radio station broadcasting program information. When
you press
on the remote controller in this state, you can use the following
functions.
Display text information (Radio Text)
1. While the name of the station is being displayed on the display, press
on the remote controller once.
Radio Text (RT) broadcast by the station is displayed scrolling across the
display. "No Text Data" is displayed when no text information is available.
Unusual characters may be displayed when the unit receives
unsupported characters. However, this is not a malfunction. Also, if the
signal from a station is weak, information may not be displayed.
Search for stations by Program Type
1. While the name of the station is being displayed on the display, press
on the remote controller twice.
2. Press / on the remote controller to select the Program Type you want
to find, then press Enter to start the search.
The Program Types displayed are as follows:
None
News (News reports)
Affairs (Current affairs)
Info (Information)
Sport
Educate (Education)
Drama
Culture
Science (Science and technology)
Varied
Pop M (Pop music)
Rock M (Rock music)
Easy M (Middle of the road music)
Light M (Light classics)
Classics (Serious classics)
Other M (Other music)
Weather
Finance
Children (Children's programmes)
Social (Social affairs)
Religion
Phone In
Travel
Leisure
Jazz (Jazz music)
Country (Country music)
Nation M (National music)
Oldies (Oldies music)
Folk M (Folk music)
Document (Documentary)
The information displayed may sometimes not match the content
being broadcast by the station.
3. When a station is found, the station flashes on the display. Press Enter
while this is happening to start receiving that station. If you don't press
Enter, the unit continues to search for another station.
If no stations are found, the message "Not Found" is displayed.
Unusual characters may be displayed when the unit receives
unsupported characters. However, this is not a malfunction. Also, if the
signal from a station is weak, information may not be displayed.
Playback Function
USB Storage Device
Playing Back
Play music files on a USB storage device.
1. Switch the input on the TV to that assigned to the unit.
2. Plug your USB storage device with the music files into the USB port of
this unit.
3. Press NET on the remote controller to display the network service list
screen.
4. With the cursors on the remote controller, select "USB", and then press
Enter.
If the "USB" indicator flashes on the display, check whether the USB
storage device is plugged in properly.
Do not unplug the USB storage device while "Connecting..." is
appeared on the display. This may cause data corruption or
malfunction.
5. Press Enter on the remote controller again in the next screen. The list of
folders and music files on the USB storage device are displayed. Select
the folder with the cursors and press Enter to confirm your selection.
6. With the cursors on the remote controller, select the music file, and then
press Enter to start playback.
The USB port of this unit conforms with the USB 2.0 standard. The
transfer speed may be insufficient for some content you play, which
may cause some interruption in sound.
To return to the previous screen, press
.
Operations with the remote controller:
1
2
3
4
5
6
/ : When the folder or file lists are not shown on one screen, you can
change the screen.
: This button plays the previous track.
: This button lets you start repeat or random playback. Pressing
this button repeatedly cycles through the repeat modes.
: Pressed during play, this button changes the displayed track
information. Pressed while a folder or file list is displayed, this button
returns you to the play screen.
: Pressed during play this button pauses playback. Pressed while
paused, and it restarts play.
: This button plays the next track.
Icons Displayed during Playback:
Icons are displayed on the display during music file playback. The meaning
of each icon is as follows:
: Folder
: Track
: Play
: Pause
: Artist
: Album
: Repeat One Track
: Repeat within a folder
: Shuffle
USB Storage Device Requirements
This unit can use USB storage devices that comply with the USB mass
storage device class standard.
FAT16 or FAT32 file system format.
If the USB storage device has been partitioned, each section will be
treated as an independent device.
Up to 20,000 tracks per folder can be displayed, and folders may be
nested up to 16 levels deep.
USB hubs and USB storage devices with hub functions are not
supported. Do not connect these devices to the unit.
USB storage devices with security function are not supported on this unit.
If you connect a USB hard disk drive to the USB port of the unit, we
recommend that you use its AC adapter to power it.
Media inserted to the USB card reader may not be available in this
function. Furthermore, depending on the USB storage device, proper
reading of the contents may not be possible.
Our company accepts no responsibility whatsoever for the loss or
damage to data stored on a USB storage device when that device is used
with this unit. We recommend that you back up your important music files
beforehand.
Supported Audio Formats
For server playback and playback from a USB storage device, this unit
supports the following music file formats. Note that sound files that are
protected by copyright cannot be played on this unit.
MP3 (.mp3/.MP3):
Supported formats: MPEG­1/MPEG­2 Audio Layer 3
Supported sampling rates: 44.1 kHz, 48 kHz
Supported bitrates: Between 8 kbps and 320 kbps. Incompatible files
cannot be played.
WMA (.wma/.WMA):
Supported sampling rates: 44.1 kHz, 48 kHz
Supported bitrates: Between 5 kbps and 320 kbps. Incompatible files
cannot be played.
WMA Pro/Voice/WMA Lossless formats are not supported
WAV (.wav/.WAV):
WAV files include uncompressed PCM digital audio.
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 8 bit, 16 bit, 24 bit
AIFF (.aiff/.aif/.aifc/.afc/.AIFF/.AIF/.AIFC/.AFC):
AIFF files include uncompressed PCM digital audio.
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/.3GP/.3G2):
Supported formats: MPEG­2/MPEG­4 Audio
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz
Supported bitrates: Between 8 kbps and 320 kbps. Incompatible files
cannot be played.
FLAC (.flac/.FLAC):
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 8 bit, 16 bit, 24 bit
Apple Lossless (.m4a/.mp4/.M4A/.MP4):
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 16 bit, 24 bit
DSD (.dsf/.dff/.DSF/.DFF):
Supported formats: DSF/DSDIFF
Supported sampling rates:
DRX­5 : 2.8 MHz, 5.6 MHz, 11.2 MHz
Others : 2.8 MHz, 5.6 MHz
Dolby TrueHD (.vr/.mlp/.VR/.MLP):
Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Variable bit­rate (VBR) files are supported. However, playback times may
not be displayed correctly.
This unit supports the gapless playback of the USB storage device in the
following conditions.
When playing WAV, FLAC and Apple Lossless, and the same format,
sampling frequency, channels and quantization bit rate are played
continuously
Playback Function
Internet Radio
TuneIn Radio
With more than 70,000 radio stations and 2 million on­demand programs
registered, TuneIn Radio is a service where you can enjoy music, sports and
news from all over the world.
Playing Back
1. Switch the input on the TV to that assigned to the unit.
2. Press NET on the remote controller to display the network service list
screen.
3. Select "TuneIn" with the cursors of the remote controller and press Enter
to confirm your selection.
4. Follow the on­screen instructions, using the cursors on the remote
controller to select radio stations and programs, then press Enter to play.
Play starts when 100% is displayed for buffering.
To return to the previous screen, press
Operations with the remote controller:
.
/ : When the station or program lists are not shown on one screen, you
can change the screen.
2 : Pressed during play, this button changes the displayed track
information. Pressed while a station or program list is displayed, this
button returns you to the play screen.
1
Regarding the TuneIn Radio Menu
To display the TuneIn Radio menu during play, press Enter on the remote
controller. Selecting the corresponding menu item with the cursors and
pressing Enter allows you to perform the following operations:
Add to My Presets: Registers radio stations being broadcast and programs
in "My Presets". Once registered, "My Presets" is displayed in the level
under TuneIn Radio. To play, select the program you like from "My Presets".
Remove from My Presets: Removes a radio station or program from "My
Presets".
Regarding the TuneIn Radio Account
Creating an account on the TuneIn Radio website (tunein.com) and logging
in it from the unit allows you to automatically add your favorite radio stations
and programs to your "My Presets" on the unit as you follow them on the
website. "My Presets" are displayed in the level under TuneIn Radio.
To display a radio station registered in "My Presets", you must log into
TuneIn Radio from the unit. To log in, select "Login" ­ "I have a Tunein
Account" in the "TuneIn Radio" top list on the unit, and then enter your user
name and password.
If you associate the device on My Page within the TuneIn Radio website
using the registration code obtained by selecting "Login" ­ "Login with a
registration code" on the unit, you can log in without entering the user
name and password.
Icons on the display
: Folder
: Radio station
: Playing
: Artist
: Album
Playback Function
Internet Radio
Pandora®–Getting Started (U.S., Australia and New Zealand
only)
Pandora is a free, personalized Internet radio service that plays the music
you know and helps you discover music you'll love.
Playing Back
1. Switch the input on the TV to that assigned to the unit.
2. Press NET on the remote controller to display the network service list
screen.
3. With the cursors on the remote controller, select "Pandora", and then
press Enter.
4. Use / on the remote controller to select "I have a Pandora Account" or
"I'm new to Pandora" and then press Enter.
If you are new to Pandora, select "I'm new to Pandora". You will see an
activation code on your TV screen. Please write down this code. Go to an
Internet connected computer and point your browser to
www.pandora.com/integra. Enter your activation code and then follow the
instructions to create your Pandora account and your personalized
Pandora stations. You can create your stations by entering your favorite
tracks and artists when prompted. After you have created your account
and stations you can return to your receiver and press Enter to begin
listening to your personalized Pandora.
If you have an existing Pandora account, you can add your Pandora
account to your receiver by selecting "I have a Pandora Account" and
logging in with your email and password.
5. To play a station, use / on the remote controller to select the station
from your station list, and then press Enter. Playback starts and the
playback screen appears.
To return to the previous screen, press
.
Operations with the remote controller:
/ : When the station or program lists are not shown on one screen, you
can change the screen.
2 : Pressed during play, this button changes the displayed track
information. Pressed while a station or program list is displayed, this
button returns you to the play screen.
3
: Pressed during play this button pauses playback. Pressed while
paused, and it restarts play.
4
: This button plays the next track.
1
Create new station
Enter the name of a track, artist, or genre and Pandora will create a unique
radio station for you based on the musical qualities of that track, artist, or
genre.
Regarding the Pandora Menu
Icons are displayed at the bottom right of the screen while playing a station.
You can do the following by selecting the icon with / on the remote
controller and pressing Enter:
(I like this track): Give a track "thumbs­up" and Pandora will play more
music like it.
(I don't like this track): Give a track "thumbs­down" and Pandora will
ban that track from the current station.
: Automatically find stations matching your preferences based on genre,
specific artists, and songs, and delete those stations you don't need.
Icons on the display
: Folder
: Radio station
: Playing
: Pause
: Artist
: Album
Playback Function
Spotify
This unit supports Spotify Connect. To enable Spotify Connect, install the
Spotify application on your smartphone or tablet and create a Spotify
premium account.
This unit needs to be connected to the same router as the smartphone or
tablet.
Refer to the following for Spotify settings:
www.spotify.com/connect/
The Spotify software is subject to third party licenses found here:
www.spotify.com/connect/third­party­licenses
Playing Back
1. Connect the smartphone to the network that this unit is connected to.
2. When the power of this unit is on, click the Connect icon in the track play
screen of the Spotify app.
3. Select this unit.
4. The input selector of this unit automatically changes to NET and
streaming of Spotify starts.
When "Network Standby" in the Setup menu is set to "On", by clicking the
Connect icon and selecting this unit, then even if this unit is in standby
mode, the power will come on automatically and streaming starts.
Operations with the remote controller:
: This button plays the previous track.
: This button lets you start repeat or random playback. Pressing
this button repeatedly cycles through the repeat modes.
3 : Pressed during play, this button changes the displayed track
information.
4
: Pressed during play this button pauses playback. Pressed while
paused, and it restarts play.
5
: This button plays the next track.
1
2
Notes for using multi­zone (for compatible models only)
To enjoy Spotify music in a separate room, manually select "NET" as the
input of the separate room. After doing that, select this unit with the
Spotify app.
Volume adjustment with the Spotify app is possible only for speakers
connected to the ZONE speaker terminals or when the volume of the
audio device in the other room is configured so that its volume can be
adjusted on this unit. Adjust the volume on the audio equipment in the
other room in any other case.
To enjoy Spotify music in the main room after playing it in a separate
room, select "NET" as the input of the main room.
Icons on the display
: Playing
: Pause
: Artist
: Album
Playback Function
Music Server
Overview
Streaming play of music files stored on PCs or NAS devices connected to
the same network as this unit is supported.
The network servers this unit is compatible with are those PCs with
players installed that have the server functionality of Windows Media®
Player 11 or 12, or NAS that are compatible with home network
functionality. You may need to make some settings in advance to use
Windows Media® Player 11 or 12. Note that only music files registered in
the library of Windows Media® Player can be played.
Playback Function
Music Server
Configuring the Windows Media® Player
Windows Media® Player 11
1. Turn on your PC and start Windows Media® Player 11.
2. In the "Library" menu, select "Media Sharing" to display a dialog box.
3. Select the "Share my media" check box, and then click "OK" to display
the compatible devices.
4. Select this unit, and then click "Allow".
When it is clicked, the corresponding icon is checked.
5. Click "OK" to close the dialog.
Depending of the version of Windows Media® Player, there may be
differences in the names of items you can select.
Windows Media® Player 12
1. Turn on your PC and start Windows Media® Player 12.
2. In the "Stream" menu, select "Turn on media streaming" to display a
dialog box.
If media streaming is already turned on, select "More streaming
options..." in the "Stream" menu to list players in the network, and then
go to step 4.
3. Click "Turn on media streaming" to list players in the network.
4. Select this unit in "Media streaming options" and check that it is set to
"Allow".
5. Click "OK" to close the dialog.
Depending of the version of Windows Media® Player, there may be
differences in the names of items you can select.
Playback Function
Music Server
Play
1. Start the server (Windows Media® Player 11, Windows Media® Player 12,
or NAS device) containing the music files to play.
2. Make sure that the PCs and/or NASs are properly connected to the same
network as this unit.
3. Press NET on the remote controller to display the network service list
screen.
If the "NET" indicator flashes in the display, the unit is not properly
connected to the network. Check the connection.
4. With the cursors on the remote controller, select "Music Server", and then
press Enter.
5. Select the target server with the cursors on the remote controller and
press Enter to display the items list screen.
The unit cannot access pictures and videos stored on servers.
Contents stored on the server may not be displayed depending on the
server sharing settings.
6. With the cursors on the remote controller, select the music file to play,
and then press Enter to start playback.
If "No Item." is displayed, check whether the network is properly
connected.
To return to the previous screen, press
.
For music files on a server, there can be up to 20,000 tracks per folder,
and folders may be nested up to 16 levels deep.
Depending on the media server, the unit may not recognize it, or may not
be able to play its music files.
Operations with the remote controller:
1
2
3
4
5
6
/ : When the folder or file lists are not shown on one screen, you can
change the screen.
: This button plays the previous track.
: This button lets you start repeat or random playback. Pressing
this button repeatedly cycles through the repeat modes.
: Pressed during play, this button changes the displayed track
information. Pressed while a folder or file list is displayed, this button
returns you to the play screen.
: Pressed during play this button pauses playback. Pressed while
paused, and it restarts play.
: This button plays the next track.
Icons Displayed during Playback:
Icons are displayed on the display during music file playback. The meaning
of each icon is as follows:
: Folder
: Track
: Playing
: Pause
: Artist
: Album
: Repeat One Track
: Repeat within a folder
: Shuffle
Playback Function
Music Server
Controlling Remote Playback from a PC
You can use this unit to play music files stored on your PC by operating the
PC inside your home network. The unit supports remote playback with
Windows Media® Player 12. To use the remote playback function with
Windows Media® Player 12, it must be configured in advance.
Setting PC
1. Turn on your PC and start Windows Media® Player 12.
2. In the "Stream" menu, select "Turn on media streaming" to display a
dialog box.
If media streaming is already turned on, select "More streaming
options..." in the "Stream" menu to list players in the network, and then
go to step 4.
3. Click "Turn on media streaming" to list players in the network.
4. Select this unit in "Media streaming options" and check that it is set to
"Allow".
5. Click "OK" to close the dialog box.
6. Open the "Stream" menu and check that "Allow remote control of my
Player..." is checked.
Depending of the version of Windows Media® Player, there may be
differences in the names of items you can select.
Remote playback
1. Turn on the power of the unit.
2. Turn on your PC and start Windows Media® Player 12.
3. Select and right­click the music file to play with Windows Media® Player
12.
To remotely play a music file on another server, open the target server
from "Other Libraries" and select the music file to play.
4. Select this unit in "Play to" to open the "Play to" window of Windows
Media® Player 12 and start playback on the unit.
Operations during remote playback are possible from the "Play to"
window on the PC. The playback screen is displayed on the TV
connected to the HDMI output of the unit. If your PC is running on
Windows® 8, click "Play to", and then select this unit.
5. Adjust the volume using the volume bar on the "Play to" window.
Sometimes, the volume displayed on the remote playback window
may differ from that appeared on the display of the unit.
When the volume is adjusted from the unit, the value is not reflected in
the "Play to" window.
This unit cannot play music files remotely in the following conditions.
– It is using a network service.
– It is playing a music file on a USB storage device.
Depending of the version of Windows Media® Player, there may be
differences in the names of items you can select.
Playback Function
Music Server
Supported Audio Formats
This unit supports the following music file formats. Note that playback via
wireless LAN of sampling rates of 88.2 kHz or higher, DSD, and Dolby
TrueHD are not supported. Remote play of FLAC, DSD, and Dolby TrueHD
is also not supported.
MP3 (.mp3/.MP3):
Supported formats: MPEG­1/MPEG­2 Audio Layer 3
Supported sampling rates: 44.1 kHz, 48 kHz
Supported bitrates: Between 8 kbps and 320 kbps. Incompatible files
cannot be played.
WMA (.wma/.WMA):
Supported sampling rates: 44.1 kHz, 48 kHz
Supported bitrates: Between 5 kbps and 320 kbps. Incompatible files
cannot be played.
WMA Pro/Voice/WMA Lossless formats are not supported
WAV (.wav/.WAV):
WAV files include uncompressed PCM digital audio.
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 8 bit, 16 bit, 24 bit
AIFF (.aiff/.aif/.aifc/.afc/.AIFF/.AIF/.AIFC/.AFC):
AIFF files include uncompressed PCM digital audio.
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/.3GP/.3G2):
Supported formats: MPEG­2/MPEG­4 Audio
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz
Supported bitrates: Between 8 kbps and 320 kbps. Incompatible files
cannot be played.
FLAC (.flac/.FLAC):
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bit: 8 bit, 16 bit, 24 bit
LPCM (Linear PCM):
Supported sampling rates: 44.1 kHz, 48 kHz
Quantization bit: 16 bit
Apple Lossless (.m4a/.mp4/.M4A/.MP4):
Supported sampling rates: 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz
Quantization bit: 16 bit, 24 bit
DSD (.dsf/.dff/.DSF/.DFF):
Supported formats: DSF/DSDIFF
Supported sampling rates:
DRX­5 : 2.8 MHz, 5.6 MHz, 11.2 MHz
Others : 2.8 MHz, 5.6 MHz
Variable bit­rate (VBR) files are supported. However, playback times may
not be displayed correctly.
Remote playback does not support the gapless playback.
Playback Function
Other Functions
Playing Audio and Video from Separate Sources
It is possible to play audio and video from different sources. For example,
you can play audio from the CD player and video from the BD/DVD player.
The procedure in this case is as follows:
1. Press BD/DVD.
2. Press CD.
3. Start playback on the BD/DVD player and CD player.
Perform the following steps to play the video from a different source to suit
the audio from a NET or BLUETOOTH input source. (for compatible models
only)
1. Press NET or
to play the audio.
2. Press Mode on the remote controller and the video input select
immediately preceding this operation can be played.
3. Start play of the video input source.
4. Each press of Mode displays or turns off the video.
Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the power on/off or
disconnecting/connecting the power cord, which is easier than working on
the connection, setting and operating procedure. Try the simple measures on
both the unit and the connected device. If the problem is that the video or
audio is not output or the HDMI linked operation does not work,
disconnecting/connecting the HDMI cable may solve it. When reconnecting,
be careful not to wind the HDMI cable since if wound the HDMI cable may
not fit well. After reconnecting, turn off and on the unit and the connected
device.
This unit contains a microPC for signal processing and control functions.
In very rare situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In the unlikely event
that this happens, unplug the power cord from the wall outlet, wait at least
5 seconds, and then plug it back in.
Our company is not responsible for reparations for damages (such as CD
rental fees) due to unsuccessful recordings caused by the unit's
malfunction. Before you record important data, make sure that the
material will be recorded correctly.
Troubleshooting
Power
Cannot turn on the unit
Make sure that the power cord is properly plugged into the wall outlet.
Unplug the power cord from the wall outlet, wait 5 seconds or more, then
plug it in again.
The unit turns off unexpectedly
The unit automatically switches to standby when the "Hardware" ­ "Power
Management" ­ "Auto Standby" setting in the Setup menu functions.
The protective circuit function may have been activated. If this has
occurred, "AMP Diag Mode" appears on the display when the unit is
turned on again, and the unit enters diagnostic mode. If the results of the
diagnosis is that there is no problem, the "AMP Diag Mode" display
disappears and you can use the unit normally again. If "CHECK SP
WIRE" appears on the display, the speaker cables may be short­circuited.
Make sure bare speaker wires are not touching each other or the back
panel of the unit, then turn the unit on again. If "NG" is displayed,
immediately unplug the power cord from the wall outlet and contact your
dealer.
The protective circuit function may have been activated because the
temperature of the unit rose abnormally. If this happens, then the power
will continue to turn off after you have turned the unit on again. Make sure
the unit has plenty of space for ventilation around it, wait for the unit to
cool down sufficiently, and then try turning it on again.
WARNING: If smoke, smell or abnormal noise is produced by the unit,
unplug the power cord from the wall outlet immediately and contact the
dealer or our company's support.
Troubleshooting
Audio
Make sure that the speaker setup microphone is not still connected.
Confirm that the connection between the output jack on the device and
the input jack on this unit is correct.
Make sure that none of the connecting cables are bent, twisted, or
damaged.
If the MUTE indicator on the display flashes, press
on the remote
controller to cancel muting.
While headphones are connected to the Phones jack, no sound is output
from the speakers.
When "Source" ­ "Audio Select" ­ "PCM Fixed Mode" in the Setup menu
is set to "On", no sound is played when signals other than PCM are input.
Change the setting to Off.
Check the following if the above does not fix the problem:
There is no sound from the TV
No sound from a connected player
A speaker produces no sound
The subwoofer produces no sound
Noise can be heard
The beginning of audio received by an HDMI IN cannot be heard
Sound suddenly reduces
Troubleshooting
There is no sound from the TV
Change the input selector on this unit to the position of the terminal to
which the TV is connected.
If the TV doesn't support the ARC function, along with connection by
HDMI, connect the TV and this unit using a digital optical cable, digital
coaxial cable, or analog audio cable.
Troubleshooting
No sound from a connected player
Change the input selector on this unit to the position of the terminal to
which the player is connected.
Check the digital audio output setting on the connected component. On
some game consoles, such as those that support DVD, the default setting
is off.
With some DVD­Video discs, you need to select an audio output format
from a menu.
Troubleshooting
A speaker produces no sound
Make sure that the polarity of the speaker cables (+/-) is correct, and
that no bare wires are in contact with the metal part of speaker terminals.
Make sure that the speaker cables are not shorting.
Check in "Connect the Speakers" in the Basic Manual that the speaker
connections have been made correctly. Settings for the speaker
connection environment need to be made in "AccuEQ Room Calibration"
in Initial Setup. Check in "Initial Setup" in the Basic Manual.
Depending on the source and current listening mode, not much sound
may be produced by the surround speakers. Select another listening
mode to see if sound is output.
If you are installing surround back speakers (for compatible models only),
surround speakers are required.
A maximum of 5.1 ch playback is possible when Bi­Amping connection is
used (for compatible models only). Further, make sure you remove the
jumper bar on the speakers when using Bi­Amping connection.
Troubleshooting
The subwoofer produces no sound
When you play source material that contains no information in the LFE
channel, the subwoofer produces no sound.
Troubleshooting
Noise can be heard
Using cable ties to bundle audio cables with power cords, speaker
cables, etc. may degrade the audio performance, so refrain from doing it.
An audio cable may be picking up interference. Try repositioning your
cables.
Troubleshooting
The beginning of audio received by an HDMI IN cannot be heard
Since it takes longer to identify the format of an HDMI signal than it does
for other digital audio signals, audio output may not start immediately.
Troubleshooting
Sound suddenly reduces
When the temperature inside the unit exceeds a certain temperature for
extended periods, the volume may be reduced automatically to protect
the circuits.
Troubleshooting
Listening Modes
To enjoy digital surround playback, such as Dolby Digital, the audio
signals need to pass through a connection via HDMI cable, digital coaxial
cable, or digital optical cable. Audio output should be set to bitstream
output on the connected Blu­ray Disc player or other device.
Press
on the remote controller several times to switch the display of
the main unit to check the input format.
Check the following if the above does not fix the problem:
Cannot select a desired listening mode
There is no sound with Dolby TrueHD, Dolby Atmos, and DTS­HD Master
Audio (for compatible models only)
About DTS signals
Troubleshooting
Cannot select a desired listening mode
Depending on the connecting status of the speaker, some listening
modes may not be selected. Check in "Selectable Listening Modes" in
"Listening Modes" in the Advanced Manual.
Troubleshooting
There is no sound with Dolby TrueHD, Dolby Atmos, and DTS­HD Master
Audio (for compatible models only)
You need to connect surround back speakers or height speakers to enjoy
Dolby Atmos. Furthermore, Dolby Atmos can only be enjoyed when the
input signals are Dolby Atmos.
If you cannot output formats such as Dolby TrueHD, Dolby Atmos, or
DTS­HD Master Audio according to the format of the source, in the Blu­
ray Disc player settings try setting “BD video supplementary sound” (or
re­encode, secondary sound, video additional audio, etc.) to “Off”.
Change the listening mode for each source after changing the setting to
confirm.
Troubleshooting
About DTS signals
With media that switches suddenly from DTS to PCM, PCM playback
may not start immediately. In such cases, you should stop your player for
about 3 seconds and then resume playback.
With some CD and LD players, you will not be able to playback DTS
material properly even though your player is connected to a digital input
on the unit. This is usually because the DTS bitstream has been
processed (e.g., output level, sampling rate, or frequency response
changed) and the unit does not recognize it as a genuine DTS signal. In
such cases, you may hear noise.
Playing DTS program material, using the pause, fast forward, or fast
reverse function on your player may produce a short audible noise. This
is not a malfunction.
Troubleshooting
Video
Confirm that the connection between the output jack on the device and
the input jack on this unit is correct.
Make sure that none of the connecting cables are bent, twisted, or
damaged.
When the TV image is blurry or unclear, power code or connection cables
of the unit may have interfered. In that case, keep distance between TV
antenna cable and cables of the unit.
Make sure the switching of input screens is proper at the monitor side
such as a TV.
Check the following if the above does not fix the problem:
There is no video
There is no picture from a source connected to an HDMI IN terminal.
Images flicker
Video and audio are out of synch
Troubleshooting
There is no video
Change the input selector on this unit to the position of the terminal to
which the player is connected.
Troubleshooting
There is no picture from a source connected to an HDMI IN terminal.
To display video from the connected player on the TV while the unit is in
standby, you need to enable "Hardware" ­ "HDMI" ­ "HDMI Standby
Through" in the Setup menu. Refer to "HDMI Setup" in "Setup" in the
Basic Manual for information about HDMI Standby Through.
To output video to a TV connected to the HDMI OUT SUB jack (for
compatible models only), in the "Quick Menu" displayed when Q is
pressed on the remote controller, select the HDMI OUT jack for output in
"Other" ­ "HDMI Out".
If you connect a player supporting HDCP2.2, be sure to connect it to one
of the HDMI IN1 to IN3 jacks of the unit.
Check if "Resolution Error" is displayed on the main unit display when
video input via HDMI IN jack is not displayed. In this case, the TV does
not support the resolution of the video input from the player. Change the
setting on the player.
Reliable operation with an HDMI­DVI adapter is not guaranteed. In
addition, video signals from a PC are not supported.
Troubleshooting
Images flicker
It is possible that the resolution of the player is not compatible with the
TV's resolution. If you have connected the player to this unit with an
HDMI cable, try changing the output resolution on the player. There also
may be an improvement if you change the screen mode on the TV.
Troubleshooting
Video and audio are out of synch
Video may be delayed relative to audio depending on the settings and
connections with your television. To adjust, press Q on the remote
controller, and adjust in "Other" ­ "A/V Sync" in the "Quick Menu".
Troubleshooting
Linked operation
There is no linked operation with CEC compliant devices, such as a TV.
In the Setup menu of the unit, set "Hardware" ­ "HDMI" ­ "HDMI CEC" to
"On".
It is also necessary to set HDMI linking on the CEC compliant device.
Check the instruction manual.
Troubleshooting
Tuner
Radio reception is poor or there is a lot of noise.
Re­check the antenna connection.
Relocate your antenna.
Move the unit away from your TV or PC.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
Listen to the station in mono.
When listening to an AM station, operating the remote controller may
cause noise.
FM reception may become clearer if you use the antenna jack on the wall
used for the TV.
Troubleshooting
BLUETOOTH function (for compatible models only)
Try plugging/unplugging the power of the unit and try turning on/off the
BLUETOOTH enabled device. Re­startup of the BLUETOOTH enabled
device may be effective.
The BLUETOOTH enabled devices must support the A2DP profile.
Near components such as microwave oven or cordless phone, which use
the radio wave in the 2.4 GHz range, a radio wave interference may
occur, which disables the use of this unit.
If there is a metallic object near the unit, BLUETOOTH connection may
not be possible as the metal can effect on the radio waves.
Check the following if the above does not fix the problem:
Cannot connect with this unit
Music playback is unavailable on the unit even after successful
BLUETOOTH connection
Sound is interrupted
The audio quality is poor after connection with a BLUETOOTH enabled
device
Troubleshooting
Cannot connect with this unit
Check that the BLUETOOTH function of the BLUETOOTH enabled
device is enabled.
Troubleshooting
Music playback is unavailable on the unit even after successful
BLUETOOTH connection
When the audio volume of your BLUETOOTH enabled device is set low,
the playback of audio may be unavailable. Volume up the BLUETOOTH
enabled device.
Depending on the BLUETOOTH enabled device, Send/Receive selector
switch may be provided. Select Send mode.
Depending on the characteristics or specifications of your BLUETOOTH
enabled device, playback on the unit is not guaranteed.
Troubleshooting
Sound is interrupted
Problem may be occurring at the BLUETOOTH enabled device. Check
the information on the internet.
Troubleshooting
The audio quality is poor after connection with a BLUETOOTH enabled
device
The BLUETOOTH reception is poor. Move the BLUETOOTH enabled
device closer to the unit or remove any obstacle between the
BLUETOOTH enabled device and this unit.
Troubleshooting
Network function
If you cannot select a network service, it will become selectable when the
network function is started. It may take about a minute to start up.
When NET is blinking, this unit is not properly connected to the home
network.
Try plugging/unplugging the power supply of this unit and the router, and
try rebooting the router.
If the desired wireless LAN router is not in the access point list, it may be
set to hide SSID or the ANY connection may be off. Change the setting
and try again. (for compatible models only)
Check the following if the above does not fix the problem:
Cannot access the Internet radio
Cannot access the network server
Playback stops while listening to music files on the network server
Troubleshooting
Cannot access the Internet radio
Certain network service or contents available through the unit may not be
accessible in case the service provider terminates its service.
Make sure that your modem and router are properly connected, and
make sure they are both turned on.
Make sure that the LAN side port on the router is properly connected to
this unit.
Make sure that connecting to Internet from other components is possible.
If connecting is not possible, turn off all components connected to the
network, wait for a while, and then turn on the components again.
If a specific radio station is unavailable for listening, make sure the
registered URL is correct, or whether the format distributed from the radio
station is supported by this unit.
Depending on ISP, setting the proxy server is necessary.
Make sure that the used router and/or modem is supported by your ISP.
Troubleshooting
Cannot access the network server
This unit needs to be connected to the same router as the network server.
This unit is compatible with Windows Media® Player 11 or 12 network
servers or NAS that are compatible with home network functionality.
You may need to make some settings on Windows Media® Player. Check
in "Music Server" in "Playback Function" in the Advanced Manual.
When using a PC, only music files registered in the Windows Media®
Player library can be played.
Troubleshooting
Playback stops while listening to music files on the network server
Make sure the network server is compatible with this unit.
When the PC is serving as the network server, try quitting any application
software other than the server software (Windows Media® Player 12,
etc.).
If the PC is downloading or copying large files, the playback may be
interrupted.
Troubleshooting
USB storage device
USB storage device is not displayed
Check whether the USB storage device or USB cable is correctly inserted
to the USB port of the unit.
Disconnect the USB storage device from the unit, and then try
reconnecting.
Performance of the hard disk that receive power from the USB port of the
unit is not guaranteed.
Depending on the type of format, the playback may not be performed
normally. Check the type of the file formats that is supported.
USB storage devices with security functions may not be played.
Troubleshooting
Wireless LAN Network (for compatible models only)
Try plugging/unplugging the power supply of wireless LAN router and the
unit, check the wireless LAN router power­on status, and try reboot of the
wireless LAN router.
Check the following if the above does not fix the problem:
Cannot access wireless LAN network
Connected to an SSID different to the SSID selected
Playback is interrupted and communication does not work
Troubleshooting
Cannot access wireless LAN network
The wireless LAN router setting may be switched to Manual. Return the
setting to Auto.
Try the manual set­up. The connection may succeed.
When the wireless LAN router setting is at stealth mode (mode to hide
the SSID key) or when ANY connection is off, the SSID is not displayed.
Change the setting and try again.
Check that the setting of SSID and encryption (WEP, etc.) is correct.
Make sure the network settings of the unit is properly set.
Connection to an SSID that includes multi­byte characters is not
supported. Name the SSID of the wireless LAN router using single­byte
alphanumeric characters only and try again.
Troubleshooting
Connected to an SSID different to the SSID selected
Some wireless LAN routers allow you to set multiple SSIDs for one unit. If
you use the automatic setting button on such a router, you may end up
connecting with a different SSID from the SSID you wanted to connect to.
Use the connection method requiring you to enter a password if this
happens.
Troubleshooting
Playback is interrupted and communication does not work
You may not receive radio waves due to bad radio wave conditions.
Shorten the distance from the wireless LAN access point or remove
obstacles to improve visibility, and try again. Place the unit away from
microwave ovens or other access points. It is recommended to place the
wireless LAN router (access point) and the unit in the same room.
If there is a metallic object near the unit, wireless LAN connection may
not be possible as the metal can effect on the radio wave.
When other wireless LAN devices are used near the unit, several issues
such as interrupted playback and communication may occur. You can
avoid these issues by changing the channel of your wireless LAN router.
For instructions on changing channels, see the instruction manual
provided with your wireless LAN router.
Troubleshooting
Multi­zone function (for compatible models only)
Cannot ZONE output audio of external AV component
Depending on the model, input by HDMI cable may not be supported.
Check in "Multi­zone Connection" in the Basic Manual, and if input by
HDMI cable is not supported, connect using a cable that is supported.
The audio from externally connected AV components can only be output
when the audio is analog or 2ch PCM audio signals. If you have
connected the AV component to this unit with a digital cable, the audio
output of the AV component needs to be set to PCM.
Others
Settings are required in Initial Setup, "Multi Zone Setup" to use the multi­
zone feature. Check in "Initial Setup" in the Basic Manual.
If the audio signal is from the NET input selector, zone output is not
possible for DSD and Dolby TrueHD audio signals.
Troubleshooting
Remote Controller
Make sure that the batteries are installed with the correct polarity.
Install new batteries. Do not mix different types of batteries, or old and
new batteries.
Make sure that the unit is not subjected to direct sunshine or inverter­type
fluorescent lights. Relocate if necessary.
If the unit is installed in a rack or cabinet with colored­glass doors or if the
doors are closed, the remote controller may not work reliably.
After operating the Multi­zone function (for compatible models only), the
remote controller may have switched to the mode for operating ZONE
output audio. Check "Multi­zone" in "Playback" in the Basic Manual to
switch the remote controller back to the mode for operating in the main
room.
Troubleshooting
Display, OSD
The display doesn't light
The display may go dim while the Dimmer is working, and may also turn
off (for compatible models only). Press Dimmer button and change the
brightness level of the display.
Troubleshooting
Others
Strange noises can be heard from the unit
If you have connected another unit to the same wall outlet as this unit,
this noise may be an effect from the other unit. If the symptoms improve
by unplugging the power cord of the other unit, use different wall outlets
for this unit and the other unit.
When performing AccuEQ Room Calibration, the message "Noise Error"
appears
This can be caused by a malfunction in your speaker unit. Check if the
unit produces normal sounds.
Reference Information
Information about products with Wi­Fi/BLUETOOTH
features (for compatible models only)
Radio Wave Caution
Products with Wi­Fi/BLUETOOTH use radio waves in the 2.4 GHz and 5GHz
frequency bands.
There are nations and regions where the use of particular 5 GHz bands are
prohibited outdoors, so do not use these products outside.
2.4 GHz radio waves are used by a variety of devices, as shown in lists 1
and 2 below.
1. Devices which use a 2.4 GHz radio wave frequency
Cordless phones
Cordless facsimiles
Microwave ovens
Wireless LAN devices (IEEE802.11b/g/n)
Wireless AV equipment
Wireless controllers for game systems
Microwave oven­based health aids
Video transmitter
Specific type of external monitor and LCD display
2. Less common devices which use a 2.4 GHz radio wave frequency
Anti­theft systems
Amateur radio stations (HAM)
Warehouse logistic management systems
Discrimination systems for train or emergency vehicles
If these devices and the AV receiver are used at the same time, the audio
may be undesirably stopped or disturbed due to a radio wave interference.
Suggestions for improvement
Switch off the devices which emit the radio wave.
Place the interfering devices away from the AV receiver.
The AV receiver uses radio wave, and a third person can receive the
wave on purpose or accidentally. Do not use the communication for
important or fatal matters.
We assume no responsibility whatsoever for any error or damage of
network environment or access device resulting from the use of this
apparatus.
Confirm with the provider or access device maker for more information.
Scope of Operation
Use of the AV receiver is limited to home use. (Transmission distances may
be reduced depending on communication environment.)
In the following locations, poor condition or inability to receive radio waves
may cause the audio to be interrupted or stopped:
In reinforced concrete buildings or steel framed or iron framed buildings.
Near large metallic furniture.
In a crowd of people or near a building or obstacle.
In a location exposed to the magnetic field, static electricity or radio wave
interference from radio communication equipment using the same
frequency band (2.4 GHz) as the AV receiver, such as a 2.4 GHz wireless
LAN device (IEEE802.11b/g/n) or microwave oven.
If you live in a heavily populated residential area (apartment, townhouse,
etc.) and if your neighbor's microwave oven is placed near your AV
receiver, you may experience radio wave interference. If this occurs,
move your AV receiver to a different place.
When the microwave oven is not in use, there will be no radio wave
interference.
Radio Wave Reflections
The radio waves received by the AV receiver include the radio wave coming
directly from the devices and waves coming from various directions due to
reflections by walls, furniture and building (reflected waves). The reflected
waves (due to obstacles and reflecting objects) further produce a variety of
reflected waves as well as variation in reception condition depending on
locations. If the audio cannot be received properly due to this phenomenon,
try moving the location of the wireless LAN device a little.
Also note that audio may be interrupted due to the reflected waves when a
person crosses or approaches the space between the AV receiver and the
wireless LAN device.
We assume no responsibility whatsoever for any damages resulting from
the use of this apparatus except in the cases deemed acceptable under
the applicable laws and regulations.
Operation in all environment is not guaranteed for wireless LAN. The
communication may not be possible or have desirable communication
speed.
Precautions
Do not use this apparatus near an electronic device handling high­
accuracy controls or weak signals. Doing so may cause an accident due
to a malfunction of the device.
Do not use this apparatus in use prohibited location such as an aircraft
equipment or a hospital. Doing so may cause an accident due to a
malfunction of an electronic device or an electro­medical apparatus.
Follow the instructions of the medical facilities.
Electronic device which requires cautions :
Hearing aid, pace maker, other medical electronic devices, fire alarm,
automatic door, and other automatic control device.
When using a pace maker or other medical electronic devices, confirm with
the medical electronic device maker or dealer for the effect of the radio
wave.
SN 29402293HTML
(C) Copyright 2016 Onkyo & Pioneer Corporation Japan. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising