Integra | DTR-70.4 | Owner Manual | Integra DTR-70.4 Receiver Owner Manual

Integra DTR-70.4 Receiver Owner Manual
AV Receiver
DTR-70.4
Instruction Manual
Safety Information and Introduction
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand,
PORTABLE CART WARNING
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the
cart/apparatus combination to
S3125A
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or water,
En-2
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or
electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and follow
local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is
adequate ventilation.
Leave 20 cm (8") of free space at the top and sides and
10 cm (4") at the rear. The rear edge of the shelf or
board above the apparatus shall be set 10 cm (4") away
from the rear panel or wall, creating a flue-like gap for
warm air to escape.
Safety Information and Introduction
Precautions
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by the dealer from whom you
purchased this unit.
8. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
• Do not leave rubber or plastic items on this unit for a
long time, because they may leave marks on the
case.
• This unit’s top and rear panels may get warm after
prolonged use. This is normal.
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be sure
to use it occasionally.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer from whom you purchased this unit or
an experienced radio/TV technician for help.
For U.S. models
Modèle pour les Canadien
For models with [Power] button, or with both
[Power] and [On/Standby] buttons:
Pressing the [Power] button to select OFF mode does
not fully disconnect from the mains. If you do not
intend to use the unit for an extended period, remove
the power cord from the AC outlet.
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
For models with [On/Standby] button only:
Pressing the [On/Standby] button to select Standby
mode does not fully disconnect from the mains. If you
do not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the
dealer from whom you purchased this unit.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
En-3
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
CLASSE B EST CONFORME À LA NORME NMB-003
DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
Safety Information and Introduction
Supplied Accessories
Make sure you have the following accessories:
Indoor FM antenna (➔ page 20)
■ Aiming the remote controller
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
Remote control sensor
AM loop antenna (➔ page 20)
(North American models) Two AM loop antennas and two
Indoor FM antennas are supplied.
AV receiver
Power cord (➔ page 21)
Speaker cable labels (➔ page 12)
Speaker setup microphone (➔ page 39)
Remote controller (RC-842M) and two batteries (AA/R6)
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
■ Installing the batteries
Approx. 16 ft. (5 m)
Thank you for purchasing an Integra AV receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will
enable you to obtain optimum performance and
listening enjoyment from your new AV receiver.
Please retain this manual for future reference.
Batteries (AA/R6)
Note
• If the remote controller doesn’t work reliably, try replacing the
batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent damage
from leakage or corrosion.
En-4
Safety Information and Introduction
Table of Contents
Safety Information and Introduction
Important Safety Instructions ......................................2
Precautions ...................................................................3
Supplied Accessories...................................................4
Table of Contents..........................................................5
Features .........................................................................6
Front & Rear Panels......................................................7
Remote Controller.......................................................10
Connections
Connecting the AV Receiver......................................11
Connecting Your Speakers .......................................11
About AV Connections ..............................................16
Connecting Components with HDMI .........................17
Connecting Your Components ..................................18
Connecting the Antennas..........................................20
Connecting Integra/Onkyo RI Components ..............21
Connecting the Power Cord ......................................21
Turning On & Basic Operations
Turning On/Off the AV Receiver ................................22
Turning On ................................................................22
Turning Off ................................................................22
Initial Setup..................................................................23
Selecting the Language
for the Onscreen Setup Menus...............................23
Audyssey MultEQ XT32: Auto Setup ........................23
Source Connection....................................................24
Remote Mode Setup .................................................24
Network Connection..................................................24
Terminating the Initial Setup .....................................24
Playback ...................................................................... 25
Playing the Connected Component .......................... 25
Controlling Contents of USB or Network Devices..... 26
Understanding Icons on the Display ......................... 27
Playing an iPod/iPhone via USB............................... 27
Playing a USB Device............................................... 28
Listening to vTuner Internet Radio............................ 28
Registering Other Internet Radio .............................. 29
Changing the Icon Layout
on the Network Service Screen.............................. 30
Playing Music Files on a Server (DLNA) .................. 30
Remote Playback...................................................... 31
Playing Music Files on a Shared Folder ................... 32
Listening to AM/FM Radio ........................................ 33
Playing Audio and Video from Separate Sources..... 37
Using Basic Functions............................................... 38
Using the Automatic Speaker Setup......................... 38
Using the Listening Modes ....................................... 41
Using the Home Menu .............................................. 49
Using the Sleep Timer .............................................. 50
Setting the Display Brightness.................................. 50
Displaying Source Information.................................. 50
Changing the Input Display....................................... 50
Using the Whole House Mode .................................. 51
Selecting Speaker Layout......................................... 51
Muting the AV Receiver ............................................ 51
Using Headphones ................................................... 52
Using Easy Macros................................................... 52
Advanced Operations
On-screen Setup......................................................... 53
Using the Quick Setup .............................................. 53
Using the Audio Settings of Quick Setup.................. 54
Using the Setup Menu (Home) ................................. 57
About the Hybrid Standby Indicator .......................... 58
Setup Menu Items..................................................... 58
Input/Output Assign .................................................. 59
Speaker Setup .......................................................... 62
Audio Adjust.............................................................. 68
Source Setup ............................................................ 72
Listening Mode Preset .............................................. 77
Miscellaneous ........................................................... 78
Hardware Setup........................................................ 79
Remote Controller Setup .......................................... 83
Lock Setup................................................................ 83
En-5
Multi Zone ................................................................... 84
Making Multi Zone Connections ............................... 84
Setting the Zone 2/3/4 Out ....................................... 86
Controlling Multi Zone Components ......................... 86
Using the 12V Triggers............................................. 87
Using the Remote Controller in
Zone and Multiroom Control Kits ........................... 88
Controlling Other Components
iPod/iPhone Playback via Onkyo Dock .................... 89
Using the Onkyo Dock.............................................. 89
Controlling Your iPod/iPhone ................................... 90
Controlling Other Components................................. 91
Preprogrammed Remote Control Codes .................. 91
Looking up for Remote Control Codes ..................... 91
Entering Remote Control Codes............................... 92
Remapping Colored Buttons .................................... 92
Remote Control Codes for Integra/Onkyo
Components Connected via RI .............................. 93
Resetting the Remote Mode Buttons........................ 93
Resetting the Remote Controller .............................. 93
Controlling Other Components ................................. 93
Learning Commands ................................................ 96
Using Normal Macros ............................................... 97
Appendix
Troubleshooting ......................................................... 98
Firmware Update ...................................................... 104
Connection Tips and Video Signal Path ................ 108
Using an RIHD-compatible TV, Player,
or Recorder ............................................................ 112
About HDMI............................................................... 114
Network/USB Features............................................. 115
License and Trademark Information ...................... 117
Specifications ........................................................... 119
To reset the AV receiver to its factory defaults, turn it
on and, while holding down CBL/SAT, press
8On/Standby (➔ page 98).
Safety Information and Introduction
Features
Amplifier
• 140 Watts/Channel @ 8 ohms (FTC)
• 200 Watts/Channel @ 6 ohms (IEC)
• 250 Watts/Channel @ 6 ohms (JEITA)
• WRAT–Wide Range Amplifier Technology
(5 Hz to 100 kHz bandwidth)
• Linear Optimum Gain Volume Circuitry
• 3 Stage Inverted Darlington Amplifier Design
• H.C.P.S.(High Current Power Supply) Massive High
Power Transformer
Processing
• THX Ultra2 Plus Certified
• Incorporates Qdeo™ technology for HDMI Video
Upscaling (to 4K Compatible)
• HQV®-Vida Video Processing with 1080p Video
upscaling of All Video Sources via HDMI
• HDMI (Audio Return Channel, 3D, DeepColor,
x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD
High Resolution Audio, Dolby TrueHD, Dolby Digital
Plus, DSD and Multi-CH PCM)
• Dolby TrueHD and DTS-HD Master Audio
• Dolby Pro Logic IIz and Audyssey DSX®
• DTS Neo:X
• Non-Scaling Configuration
• A-Form Listening Mode Memory
• Direct Mode
• Music Optimizer for Compressed Digital Music files
• 192 kHz/24-Bit D/A Converters
• Powerful and Highly Accurate 32-bit Processing DSP
• Jitter Cleaning Circuit Technology
• Digital Processing Crossover Network
• DSD Direct for Super Audio CD
Connections
Miscellaneous
• 9 HDMI Inputs (1 on front panel) and 2 Outputs
• Zone 2 HDMI Output
• Integra/Onkyo p for System Control
• 6 Digital Inputs (3 Optical/3 Coaxial)
• Component Video Switching (2 Inputs/1 Output)
• Banana Plug-Compatible Speaker Posts
• Powered Zone 2/3/4
• Zone 2/3/4 Pre/Line Out
• IR Input/Output and 12 V Triggers
• RS232 Port for Interface Control
• Bi-Amping Capability for FL/FR with FHL/FHR
• Analog RGB Video Input (D-sub 15) for PC
• 2 Independent Subwoofer Pre Outs Capable of 4
Connections
• (North American models) HD Radio Capability
• Internet Radio Connectivity
• Network Capability for Streaming Audio Files
• 2 USB Inputs (Front/Rear) for Memory Devices and
iPod®/iPhone® models
• 40 FM/AM Presets
• Dolby Volume
• Audyssey MultEQ® XT32 to correct room acoustic
problems
• Audyssey Dynamic EQ® for loudness correction
• Audyssey Dynamic Volume® to maintain optimal
listening level and dynamic range
• Crossover Adjustment
(40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz)
• A/V Sync Control Function (up to 800 ms)
• Auto Standby Function
• On-Screen Display via HDMI
• Preprogrammed (with onscreen display setup)
RI-Compatible Learning Remote with 4 Activities and
Mode-Key LEDs
• ISF (Imaging Science Foundation) Video Calibration
• VLSC (Vector Linear Shaping Circuitry) for All
Channels
*
Only the front-panel USB input is compatible with
iPod/iPhone and Onkyo wireless LAN adapter UWF-1.
• MHL-Enabled AUX Front Input
En-6
Safety Information and Introduction
Front & Rear Panels
Front Panel
(North American models)
a
b
pq r
cd
(Australian models)
e f
s
g
h i j kl m n
t
u
w
o
v
For detailed information, see the pages in parentheses.
a 8On/Standby button (22)
j Tuning Mode button (33)
k Display button (50)
t Input selector buttons (25)
b Hybrid Standby indicator (58)
l Setup button (57)
u USB port (18)
c Monitor Out button (59)
d Remote control sensor (4)
m Tuning q/w (33), Preset e/r (33), cursor and
Enter buttons
w RT/PTY/TP button (Australian models) (36)
e Tone and Tone Level buttons (54, 87)
n Return button
f Display (8)
o Master Volume control (25)
g Listening Mode buttons (41)
p Zone 2/Zone 3/Zone 4 and Off buttons (86)
h Dimmer button (North American models) (50)
q Whole House Mode and Off buttons (51)
i Memory button (33)
r Phones jack (52)
En-7
s Setup Mic jack (39)
v AUX Input jacks (17, 18)
Safety Information and Introduction
Display
s
a bc d e f g
k
l m
For detailed information, see the pages in parentheses.
a Speaker/channel indicators
n
c Z2 (Zone 2) indicator (86)
j Input indicators (110)
HDMI indicator (80)
DIGITAL indicator
ANALOG indicator
d Z4 (Zone 4) indicator (86)
k Bi AMP indicator
e Listening mode and format indicators (41, 77)
l Audyssey indicator (38, 72)
Dynamic EQ indicator (72)
b Z3 (Zone 3) indicator (86)
f M.Opt indicator (56)
g 1, 3 and cursor indicators (27)
h NET indicator (28 to 32, 82)
i Tuning indicators
HD indicator (North American models) (34)
SPS indicator (North American models) (34)
RDS indicator (excluding North American models)
(35)
AUTO indicator (33)
TUNED indicator (33)
FM STEREO indicator (33)
- (Dolby) Vol indicator
Dynamic Vol indicator (72)
m Headphone indicator (52)
n Message area
o MUTING indicator (51)
p Volume level
q USB indicator (27, 28)
r SLEEP indicator (50)
En-8
h
i
j
o
p
q r
Safety Information and Introduction
Rear Panel
(North American models)
a bc d
o
(Australian models)
e
p
f
g
q
h ij
k
r
l m n
s
a RS232 port
Terminal for control.
k ZONE 2, ZONE 3 and ZONE 4 L/R/SUBWOOFER
PRE/LINE OUT jacks
b DIGITAL IN COAXIAL and OPTICAL jacks
l MAIN/ZONE 2 FM ANTENNA jacks and
MAIN/ZONE 2 AM ANTENNA terminals
c USB port
t
d ETHERNET port
m PC IN jack
e u REMOTE CONTROL jack
n AC INLET
f HDMI IN and HDMI output (HDMI OUT MAIN and
HDMI OUT SUB/ZONE 2) jacks
o GND screw
g COMPONENT VIDEO IN and MONITOR OUT
jacks
p Composite video and analog audio jacks
(BD/DVD IN, CBL/SAT IN, STB/DVR IN, GAME 1
IN, PC IN, TV/CD IN and PHONO IN)
h IR IN A/B and OUT jacks
q MONITOR OUT V jack
i 12V TRIGGER OUT A/B/C jacks
j ZONE 2 OUT V jack
En-9
r PRE OUT jacks
(FRONT L/R, CENTER, SURR L/R, SURR BACK
L/R, FRONT HIGH L/R, FRONT WIDE L/R, SW1
and SW2)
s Speaker Terminals
(FRONT L/R, CENTER, SURR L/R,
SURR BACK/ZONE 4 L/R,
FRONT HIGH/ZONE 3 L/R and
FRONT WIDE/ZONE 2 L/R)
t FM ANTENNA jack and AM ANTENNA terminal
See “Connecting the AV Receiver” for connection
(➔ pages 11 to 21).
Safety Information and Introduction
Remote Controller
Controlling the AV Receiver
a
b
i
c
To control the AV receiver, press Receiver to select
Receiver mode.
You can also use the remote controller to control
Integra/Onkyo Blu-ray Disc/DVD player, CD player,
and other components.
See “Entering Remote Control Codes” for more
details (➔ page 92).
For detailed information, see the pages in parentheses.
a 8Receiver button (22)
c
■ Controlling the tuner
To control the AV receiver’s tuner, press Tuner (or
Receiver).
You can select AM or FM by pressing Tuner repeatedly.
a q/w buttons (33)
b D.TUN button (33)
c Display button
d CH +/– button (34)
e Number buttons (33)
b Activities buttons (52, 97)
*2
*1
j
*2
d
e
a
f
k
d
c Remote Mode/Input Selector buttons (25)
d SP (speaker layout) button (51)
e q/w/e/r and Enter buttons
f Q Setup button (53)
g Listening Mode buttons (41)
h Dimmer button (50)
l
m
i Display button (50)
j Muting button (51)
k VOL q/w button (25)
l Return button
m Home button (49)
g
n Sleep button (50)
e
h
b
*1
n
En-10
*2
When you want to change the remote controller mode (target
component) without changing the current input source, press
Mode and within about 8 seconds, press Remote Mode.
Then, using the same AV receiver’s remote controller, you can
control the component corresponding to the button you
pressed.
These buttons can also be used when a Remote Mode other
than Receiver mode is selected.
Connections
Connecting the AV
Receiver
Connecting the Speaker Cables
■ 9.2-channel playback
The following illustration shows how to connect the speakers to each pair of terminals. If you’re using only one surround
back speaker, connect it to the SURR BACK L terminals. Select the speakers (surround back and front high,surround back
and front wide, or front high and front wide) you want to use for 9.2-channel playback. You can set which speakers you
want to use by priority. See “Selecting Speaker Layout” (➔ page 51).
Connecting Your Speakers
Speaker Configuration
The following table indicates the channels you should use
depending on the number of speakers that you have.
No matter how many speakers you use, 2 powered
subwoofers are recommended for a really powerful and
solid bass.
To get the best from your surround sound system, you need
to set the speaker settings automatically (➔ page 38) or
manually (➔ page 64).
Number of
speakers
Front high
right
Front wide
right
Front right
Front left
Front wide
left
Front high
left
Center
2 3 4 5 6 7 7 7 8 8 9 9 9 10 11
Front speakers ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Center speaker
Surround
speakers
Surround back
speaker*1
Surround back
speakers
Front high
speakers
Front wide
speakers
*1
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔
✔
✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔ ✔
If you’re using only one surround back speaker, connect it to
the SURR BACK L terminals.
Surround
right
Surround
back right
■ Screw-type speaker terminals
Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends
of the speaker cables, and twist the bare wires tightly, as
shown.
1/2" to 5/8" (12 to 15 mm)
En-11
Surround
back left
Surround
left
■ Banana Plugs (North American models)
• If you are using banana plugs, tighten the speaker
terminal before inserting the banana plug.
• Do not insert the speaker code directly into the center
hole of the speaker terminal.
Connections
■ 11.2-channel playback
By using a combination of the built-in power amplifier for
9-channel and an external power amplifier for 2-channel,
you can enjoy up to 11.2-channel playback. Connect the
external power amplifier's analog audio input jacks to
FRONT WIDE PRE OUT of the AV receiver with audio
cables. To perform the 11.2-channel playback, set the
“11ch Playback” setting to “Yes” (➔ page 63).
Attaching the Speaker Cable Labels
Speaker Connection Precautions
The speaker terminals are color-coded for identification
purpose.
Read the following before connecting your speakers:
• You can connect speakers with an impedance of between
4 and 16 ohms. If the impedance of any of the connected
speakers is 4 ohms or more, but less than 6 ohms, be sure
to set the minimum speaker impedance to “4ohms”
(➔ page 63). If you use speakers with a lower
impedance, and use the amplifier at high volume levels
for a long period of time, the built-in protection circuit
may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the positive and negative wires.
Doing so may damage the AV receiver.
• Make sure the metal core of the wire does not have
contact with the AV receiver’s rear panel. Doing so may
damage the AV receiver.
Speaker
Color
Front left, Front high left, Front wide left,
Zone 2 left, Zone 3 left
White
Front right, Front high right, Front wide
right, Zone 2 right, Zone 3 right
Red
Center
Green
Surround left
Blue
Surround right
Gray
Surround back left, Zone 4 left
Brown
Surround back right, Zone 4 right
Tan
The supplied speaker cable labels are also color-coded and
you should attach them to the positive (+) side of each
speaker cable in accordance with the table above. Then all
you need to do is to match the color of each label to the
corresponding speaker terminal.
Power amplifier
Front wide right
Front wide left
Note
• If the “11ch Playback” setting is set to “Yes”, no sound is output
from the FRONT WIDE terminals.
En-12
Connections
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
You can use dipole speakers for the surround and surround
back speakers. Dipole speakers output the same sound in
two directions.
Dipole speakers typically have an arrow printed on them to
indicate how they should be positioned. The surround
dipole speakers (a) should be positioned so that their
arrows point toward the TV/screen, while the surround
back dipole speakers (b) should be positioned so that their
arrows point toward each other, as shown.
Using Powered Subwoofers
To find the best position for your subwoofer, while playing
a movie or some music with good bass, experiment by
placing your subwoofer at various positions within the
room, and choose the one that provides the most satisfying
results.
You can connect the powered subwoofers with SW1 PRE
OUT and SW2 PRE OUT respectively.
The level and distance can be set individually for each
output. If you’re using only one subwoofer, connect it to
SW1 PRE OUT.
Tip
• If your subwoofer is unpowered and you’re using an external
amplifier, connect the subwoofer pre out jack to an input on the
amplifier.
LINE INPUT
LINE INPUT
LINE INPUT
LINE INPUT
LINE INPUT
LINE INPUT
LINE INPUT
LINE INPUT
Using Dipole Speakers
Powered subwoofer
Powered subwoofer
TV/screen
a
Corner
position
a
b
b
1/3 of wall
position
En-13
Connections
Connecting Passive Subwoofers
Bi-amping the Front Speakers
The FRONT HIGH/ZONE 3 L/R terminals can be used
with front high speakers, Zone 3 speakers, or passive
subwoofers.
The level and distance can be set for SUBWOOFER1 and
SUBWOOFER2 respectively.
Once you’ve connected the passive subwoofers and turned
on the AV receiver, you need to enable the “Passive
Subwoofer” setting (➔ page 63).
If you use one passive subwoofer, connect it to the
SUBWOOFER1 terminals.
Subwoofer 2
Subwoofer 1
Using Speakers Without Crossover Network
Important:
Important:
• When making the bi-amping connections, be sure to remove
the jumper bars that link the speakers’ tweeter (high) and
woofer (low) terminals.
• Bi-amping can be used only with speakers that support biamping. Refer to your speaker manual.
• Speakers without crossover network are speakers with no
built-in crossover network.
• With speakers without crossover network, be careful NOT to
connect tweeters and woofers the wrong way around, as this
may damage your speakers.
• With speakers without crossover network, be careful NOT to
set “Speakers Type(Front)” to “Bi-Amp” as this may damage
your speakers. Make sure that this setting is set to “Digital
Crossover”.
• Confirm that your speakers are without crossover network by
referring to your speaker manual.
Bi-amping provides improved bass and treble performance.
When bi-amping is used, the AV receiver is able to drive
up to a 7.2 speaker system in the main room.
Once you’ve completed the bi-amping connections as
shown and turned on the AV receiver, you must set the
speaker setting to enable bi-amping (➔ page 63).
Connecting speakers without crossover network provide a
fine, three-dimensional sound field that extends bass and
treble performance to the fullest extent. When speakers
without crossover network are used, the AV receiver is
able to drive up to a 7.2 speaker system in the main room.
You must enable “Digital Crossover” in “Speakers
Type(Front)” (➔ page 63) and make the settings of
“Digital Processing Crossover Network” (➔ page 67).
Note
• You need to make the setting before connecting the speakers.
Tweeter (high)
Woofer (low)
Front right
Front left
Tweeter (high)
Woofer (low)
Front right
En-14
Front left
Connections
Connecting a Power Amplifier
If you want to use a more powerful power amplifier, you
can use the AV receiver as a preamp. Connect all speaker
outputs to the power amplifier. See the manuals supplied
with your amplifier for details.
L
R
Power amplifier
Note
• Specify “None” for any channel that you don’t want to output
(➔ page 64).
• To perform the 11.2-channel playback, set the “11ch Playback”
setting to “Yes” (➔ page 63).
En-15
Connections
About AV Connections
Connecting AV components
a
HDMI cable
: Video & Audio
TV, projector, etc.
*1
• Push plugs in all the way to make
good connections (loose connections
can cause noise or malfunctions).
• To prevent interference, keep audio
and video cables away from power
cords and speaker cables.
Right!
■ Optical digital audio
Optical digital connections allow you to enjoy digital
sound such as PCM*2, Dolby Digital or DTS. The audio
quality is the same as coaxial.
Wrong!
AV Cables and Jacks
AV receiver
■ HDMI
HDMI connections can carry digital video and audio.
■ Coaxial digital audio
Coaxial digital connections allow you to enjoy digital
sound such as PCM*2, Dolby Digital or DTS. The audio
quality is the same as optical.
Orange
Blu-ray Disc/
DVD player
Other cables
Game console
: Audio
: Video
TV, projector, etc.
■ Component video
Component video separates the luminance (Y) and color
difference signals (PB, PR), providing the best picture
quality (some TV manufacturers label their component
video sockets slightly differently).
■ Analog audio (RCA)
Analog audio connections (RCA) carry analog audio.
White
Red
AV receiver
Blu-ray Disc/
DVD player
*1
Game console
If your TV doesn’t support Audio Return Channel (ARC), you
need to connect an optical digital cable together with the
HDMI cable to the AV receiver.
• Before making any AV connections, read the manuals
supplied with your AV components.
• Don’t connect the power cord until you’ve completed and
double-checked all AV connections.
Y
Green
PB
Blue
PR
Red
■ Analog RGB
This is a conventional analog interface to connect a PC and
a display device (also called D-Sub or D-subminiature).
*2
For PCM signals, the supported sampling rates are
32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4 and
192 kHz are also supported.
Note
• The AV receiver does not support SCART plugs.
• The AV receiver’s optical digital jacks have shutter-type covers
that open when an optical plug is inserted and close when it’s
removed. Push plugs in all the way.
Caution
■ Composite video
Composite video is commonly used on TVs, DVDs, and
other video equipment.
Yellow
En-16
• To prevent shutter damage, hold the optical plug straight
when inserting and removing.
Connections
Connecting Components with HDMI
Satellite/cable set-top box, etc.
Personal computer
TV, projector, etc.
Camcorder, etc.
Blu-ray Disc/DVD player
Game console
Set top box/digital video recorder, etc.
*
*
If your TV doesn’t support Audio Return Channel (ARC), you
need to connect an optical digital cable together with the HDMI
cable to the AV receiver.
When listening to an HDMI component through the AV
receiver, set the HDMI component so that its video can be seen
on the TV screen (on the TV, select the input of the HDMI
component connected to the AV receiver). If the TV power is off
or the TV is set to another input source, this may result in no
sound from the AV receiver or the sound may be cut off.
Connect your components to the appropriate jacks. The
default input assignments are shown below.
✔: Assignment can be changed (➔ page 60).
Jack
Components
IN1
Blu-ray Disc/DVD player
✔
IN2
Satellite/cable set-top box, etc.
✔
IN3
Set top box/digital video recorder, etc.
✔
IN4
Game console
✔
IN5
Game console
✔
IN6
Personal computer
✔
IN7
Other components
✔
IN8
Other components
✔
Front
Camcorder, etc.
OUT MAIN
TV
OUT SUB
Projector, etc.
See also:
• “Connection Tips and Video Signal Path” (➔ page 108)
• “Using an RIHD-compatible TV, Player, or Recorder”
(➔ page 112)
• “About HDMI” (➔ page 114)
En-17
Tip
• To listen to the audio of a component connected via HDMI
through your TV’s speakers, enable “HDMI Through”
(➔ page 80) and set the AV receiver to standby mode.
Note
• In the case of Blu-ray Disc/DVD players, if no sound is output
despite following the above-mentioned procedure, set your Bluray Disc/DVD player’s HDMI audio settings to PCM.
■ Audio Return Channel (ARC) function
The Audio Return Channel (ARC) function enables an
HDMI capable TV to send the audio stream to HDMI OUT
MAIN on the AV receiver.
• This function can be used when:
– Your TV is ARC capable, and
– The TV/CD input selector is selected, and
– “HDMI Control(RIHD)” is set to “On”(➔ page 80), and
– “Audio Return Channel” is set to “Auto” (➔ page 81).
■ MHL (Mobile High-Definition Link)
With its support for MHL (Mobile High-Definition Link),
the AUX (Front) input allows you to deliver highdefinition video from a connected mobile device.
Connections
Connecting Your Components
The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other
video outputs, use the AV receiver’s display when changing settings.
Connect your components to the appropriate jacks. The
default input assignments are shown below. See
“Connection Tips and Video Signal Path” for more
information (➔ page 108).
✔: Assignment can be changed (➔ pages 61, 62).
No. Jack/Port
A
B
C
Components
A
USB*1*2
B
USB, AUX Input Video*3 iPod/iPhone (video
playback)
C
AUX Input
Video
iPod/iPhone, MP3 player,
USB flash drive
Camcorder, etc
Audio L/R
Digital
D
D A E F
G
H
I
J
K
DIGITAL IN
COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player
✔
COAXIAL 2 (CBL/SAT) Satellite/cable set-top box,
etc.
✔
COAXIAL 3 (STB/DVR) Set top box/digital video
recorder, etc
✔
OPTICAL 1 (GAME 1)
Game consoles
✔
OPTICAL 2 (TV/CD)
TV, CD player
✔
E
ETHERNET
Router
F
AUDIO IN
BD/DVD
Blu-ray Disc/DVD player
CBL/SAT
Satellite/cable set-top box,
etc.
STB/DVR
Set top box/digital video
recorder, etc
GAME 1
Game console, RI dock
PC
Personal computer
TV/CD
TV, CD player, cassette
tape deck, MD, CD-R,
Turntable*4, RI dock
PHONO
Turntable*4
To be continued
GND screw
En-18
Connections
No. Jack/Port
G
Components
VIDEO IN
1 (BD/DVD)
Blu-ray Disc/DVD player
✔
2 (CBL/SAT)
Satellite/cable set-top box,
etc.
✔
3 (STB/DVR)
Set top box/digital video
recorder, etc
✔
4 (GAME 1)
Game console, RI dock
✔
H
MONITOR OUT
TV, projector, etc.
I
COMPONENT VIDEO
MONITOR OUT
TV, projector, etc.
IN 1 (BD/DVD)
Blu-ray Disc/DVD player,
RI dock
✔
IN 2 (CBL/SAT)
Satellite/cable set-top box,
RI dock, etc.
✔
J
ZONE 2 OUT
TV, projector, etc.
K
PC IN*5
Personal computer
Note
*1
*2
*3
*4
Do not connect the AV receiver’s USB port to a USB port on
your computer. Music on your computer cannot be played
through the AV receiver in this way.
Only the front-panel USB input is compatible with
iPod/iPhone and Onkyo wireless LAN adapter UWF-1.
UWF-1 can be used with the contents of not more than 64 kHz,
not compatible with Dolby TrueHD and DSD.
When the USB input is selected, you can input video signals
from the AUX Input Video jack. Video signals input from
AUX Input Video will be output from MONITOR OUT V,
COMPONENT VIDEO MONITOR OUT, and the HDMI
output jacks.
Select which of COMPONENT VIDEO MONITOR OUT
and the HDMI output jacks will output the video signal in the
“Monitor Out” setting (➔ page 59).
Connect a turntable (MM) that has a built-in phono preamp to
TV/CD IN, or connect it to PHONO IN with the phono
preamp turned off. If your turntable (MM) doesn’t have a
phono preamp, connect it to PHONO IN. If your turntable has
a moving coil (MC) type cartridge, you’ll need a commercially
available MC head amp or MC transformer to connect to
PHONO IN. See your turntable’s manual for details.
*5
If your turntable has a ground wire, connect it to the AV
receiver’s GND screw. With some turntables, connecting the
ground wire may produce an audible hum. If this happens,
disconnect it.
When you connect your personal computer to PC IN and select
the PC input selector, the video of the personal computer is
output from the HDMI outputs. However, if you have assigned
the HDMI inputs to the PC input selector, the AV receiver will
output signals received from the HDMI inputs instead of
signals from PC IN, based on the priority order of HDMI >
component video > PC IN (analog RGB). To have the signals
output from PC IN, select “- - - - -” for “PC” in the “HDMI
Input” setting (➔ page 60).
• With connection D, you can enjoy Dolby Digital and
DTS. (To listen in Zone 2/3/4 as well, use D and F.)
• With connection G, you can enjoy analog video from
external components while you are in Zone 2.
• With connection F, you can enjoy audio from external
components while you are in Zone 2/3/4.
• With connection F, if your Blu-ray Disc/DVD player
has both the main stereo and multichannel outputs, be
sure to connect the main stereo.
En-19
Connections
Connecting the Antennas
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.
(North American models)
Push.
Insert wire.
(Australian models)
Release.
Assembling the AM loop antenna
Insert the plug fully into the jack.
Push.
Insert wire.
Release.
Caution
Caution
Assembling the AM loop antenna
• Be careful not to injure
yourself when using
thumbtacks.
Indoor FM antenna (supplied)
AM loop antenna (supplied)
Tip
• If you want to select different radio stations for the main room and Zone 2 respectively, connect the
indoor FM antenna or AM loop antenna to the ZONE 2 FM ANTENNA jack or the ZONE 2 AM
ANTENNA terminal.
Note
• When using the Whole House Mode with “TUNER” input selector, connect antennas to both the MAIN
and ZONE 2 ANTENNA jacks/terminals (➔ pages 51, 86).
Note
• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.
• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.
Tip
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.
• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.
En-20
• Be careful not to injure
yourself when using
thumbtacks.
Thumbtacks, etc.
Thumbtacks, etc.
AM loop antenna (supplied)
Insert the plug fully into the jack.
Indoor FM antenna (supplied)
Connections
Connecting Integra/Onkyo RI
Components
1
Make sure that each Integra/Onkyo component is
connected with an analog audio cable (connection
F in the hookup examples) (➔ page 18).
2
3
Make the u connection (see the illustration).
■ Remote Control
You can use the AV receiver’s remote controller to
control your other u-capable Integra/Onkyo
components, pointing the remote controller at the AV
receiver’s remote control sensor instead of the
component. You must enter the appropriate remote
control code first (➔ page 93).
Connecting the Power Cord
1
Connect the supplied power cord to the AV
receiver’s AC INLET.
If you’re using an RI Dock, or cassette tape deck,
change the Input Display (➔ page 50).
To AC wall outlet
With u (Remote Interactive), you can use the following
special functions:
■ Auto Power On
When you start playback on a component connected via
u, while the AV receiver is on standby, the AV
receiver will automatically turn on and select that
component as the input source.
2
Plug the power cord into an AC wall outlet.
Note
e.g., cassette tape deck
■ Direct Change
When playback is started on a component connected via
u, the AV receiver automatically selects that
component as the input source.
■ System Off
When you turn off the AV receiver, the components turn
off automatically.
RI Dock
R
L
ANALOG
AUDIO OUT
R
L
ANALOG
AUDIO OUT
Note
• Use only u cables for u connections. u cables are supplied
with Integra/Onkyo components.
• Some components have two u jacks. You can connect either
one to the AV receiver. The other jack is for connecting
additional u-capable components.
• Connect only Integra/Onkyo components to u jacks.
Connecting other manufacturer’s components may cause a
malfunction.
• Some components may not support all u functions. Refer to the
manuals supplied with your Integra/Onkyo components.
• While Zone 2/3/4 is on, the System Off, Auto Power On and
Direct Change u functions do not work.
En-21
• Before connecting the power cord, connect all of your
speakers and AV components.
• Turning on the AV receiver may cause a momentary power surge
that might interfere with other electrical equipment on the same
circuit. If this is a problem, plug the AV receiver into a different
branch circuit.
• Do not use a power cord other than the one supplied with the AV
receiver. The supplied power cord is designed exclusively for use
with the AV receiver and should not be used with any other
equipment.
• Never disconnect the power cord from the AV receiver while the
other end is still plugged into a wall outlet. Doing so may cause
an electric shock. Always disconnect the power cord from the
wall outlet first, and then the AV receiver.
Turning On & Basic Operations
Turning On/Off the AV
Receiver
Turning On
1
8On/Standby
Press 8On/Standby on the front panel.
or
Press Receiver followed by 8Receiver on the
remote controller.
The AV receiver comes on and its display lights.
Turning Off
1
Press 8On/Standby on the front panel.
or
Press Receiver followed by 8Receiver on the
remote controller.
The AV receiver will enter standby mode. To prevent
any loud surprises when you turn on the AV receiver,
always turn down the volume before you turn it off.
Tip
• The Hybrid Standby indicator may light depending on the
status of settings (➔ page 58).
• For details on power management settings, see “Auto Standby”
(➔ page 82).
■ Smooth Operation in a Few Easy Steps
(Initial Setup)
To ensure smooth operation, here’s a few easy steps to
help you configure the AV receiver before you use it for
the very first time. These settings only need to be made
once. See “Initial Setup” for details (➔ page 23).
■ If the “Firmware Update Available” window
appears.
When a new version of the firmware is available, the
notification window “Firmware Update Available”
pops up. This notification only appears when the AV
receiver is connected to your home network
(➔ page 115). To perform the firmware update, follow
the instructions on screen.
Use q/w and Enter on the AV receiver or remote
controller to select one of the options.
`Update Now:
Starts the firmware update.
Refer to “Firmware Update” (➔ page 104).
`Remind me Later:
The update notification will pop up again the next
time you turn the AV receiver on.
`Never Remind me:
Disables the automatic update notification.
Tip
8Receiver
• The update notification window can be enabled or disabled in
“Update Notice” (➔ page 82).
Receiver
En-22
Turning On & Basic Operations
Initial Setup
This section explains the settings that we recommend you
to make before using the AV receiver for the very first
time. A setup wizard is launched upon first-time use to let
you perform those settings.
Selecting the Language for the
Onscreen Setup Menus
This step determines the language used for the onscreen
setup menus. See “Language” in “OSD Setup”
(➔ page 79).
Tip
The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.
• Pressing Home will close the setup wizard. To restart the initial
setup, select “Initial Setup” in the “Hardware Setup” menu
(➔ page 82).
After selecting the language for on-screen setup menus, a
welcome screen is displayed.
Initial Setup
Welcome to initial setup. Have you connected all the speakers and devices?
Before starting, please connect speakers and sources.
Now, would you like to start initial setup?
1st Step : Audyssey MultEQ XT32: Auto Setup
2nd Step : Source Connection
3rd Step : Remote Mode Setup
4th Step : Network Connection
Yes
No
HOME Exit
1
Use q/w on the AV receiver or remote controller to
select one of the following options, and then press
Enter.
` Yes:
Continues to “Audyssey MultEQ XT32: Auto
Setup”.
` No:
Skips the settings and terminates the initial
setup. The setup wizard goes to “Terminating the
Initial Setup” (➔ page 24). You can always
restart the initial setup by selecting “Initial
Setup” in the “Hardware Setup” menu
(➔ page 82).
En-23
Audyssey MultEQ XT32: Auto Setup
This step performs the automatic speaker setup.
1
Use q/w to select one of the following options, and
then press Enter.
` Do it Now:
The automatic speaker setup is performed
following instructions on screen. Refer to step 2
of “Using the Automatic Speaker Setup”
(➔ page 38). When this setting is complete, the
setup wizard continues to “Source Connection”.
` Do it Later:
Skips this setting.
Press Enter and continue to “Source
Connection”.
Turning On & Basic Operations
Source Connection
This step checks the connection of source components.
1
2
3
4
Use q/w to select one of the following options, and
then press Enter.
`Yes, Continue:
Performs the checkings.
`No, Skip:
Skips this step and continues to “Remote Mode
Setup”.
Select the input selector for which you want to
check the connection and press Enter.
The picture of the corresponding source should appear
on screen with a verification prompt.
Remote Mode Setup
With this step, you can enter remote control codes for the
components you want to operate.
1
2
When prompted, use q/w to select one of the
following options and then press Enter.
`Yes:
Confirms that the source is properly displayed.
`No:
Displays an error report. Follow the
troubleshooting instructions and recheck the
source.
Use q/w to select one of the following options, and
then press Enter.
`Yes:
Returns to step 2.
`No, Done Checking:
The setup wizard continues to “Remote Mode
Setup”.
2
Use q/w to select one of the following options, and
then press Enter.
` Yes:
Performs the remote control code input. Refer to
step 5 of “Looking up for Remote Control
Codes” (➔ page 91).
` No, Skip:
Skips this step and continues to “Network
Connection”.
Follow the instructions on screen to perform the
network checking.
The checking is complete when the message
“Successfully connected.” appears at the middle of
the screen. Press Enter to terminate the initial setup.
Tip
• If you have selected “Wireless (Option)”, you need to
configure the optional wireless adapter. For further details,
see the instruction manual provided with the wireless
adapter (UWF-1).
3
When you’re finished, select one of the following
options and press Enter.
` Yes, Done:
The setup wizard continues to “Network
Connection”.
` No, not yet:
You can enter other remote control codes.
If an error message appears, select one of the
following options and press Enter.
` Retry:
Performs the checking again.
` No, Do it Later:
Skips this step and terminates the initial setup.
The setup wizard goes to “Terminating the
Initial Setup”.
Terminating the Initial Setup
This step ends the initial setup process.
Network Connection
This step checks your network connection.
1
Use q/w to select one of the following options, and
then press Enter.
` Yes:
Performs the checkings.
` No, Skip:
Skips this step and terminates the initial setup.
En-24
1
Press Enter.
To restart the initial setup, select “Initial Setup” in
the “Hardware Setup” menu (➔ page 82).
Turning On & Basic Operations
Playback
2
The on-screen information appears only on a TV that
is connected to HDMI outputs. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
This section describes the procedure for using the
remote controller, unless otherwise specified.
Playing the Connected Component
■ Operating with the remote controller
Input Selector
Receiver
VOL q/w
3
4
Start playback on the source component.
See also:
• “Playing an iPod/iPhone via USB” (➔ page 27)
• “Playing a USB Device” (➔ page 28)
• “Listening to vTuner Internet Radio” (➔ page 28)
• “Registering Other Internet Radio” (➔ page 29)
• “Playing Music Files on a Server (DLNA)”
(➔ page 30)
• “Remote Playback” (➔ page 31)
• “Playing Music Files on a Shared Folder”
(➔ page 32)
• “Listening to AM/FM Radio” (➔ page 33)
• “Playing Audio and Video from Separate Sources”
(➔ page 37)
• “iPod/iPhone Playback via Onkyo Dock”
(➔ page 89)
• “Controlling Other Components” (➔ page 91)
To adjust the volume, use VOL q/w.
Select a listening mode and enjoy!
See also:
• “Using the Listening Modes” (➔ page 41)
• “Sound Program Edit” (➔ page 71)
■ Operating on the AV receiver
Listening Mode
Master Volume
Input selector buttons
1
Use the input selector buttons to select the input
source.
2
3
Start playback on the source component.
4
Select a listening mode and enjoy!
To adjust the volume, use the Master Volume
control.
■ Screen Saver
If there is no video signal on the current input source and
no operation for a specific time (three minutes by
default), a screen saver automatically comes on.
Tip
• The time until the screen saver activates itself can be changed
in the “Screen Saver” setting (➔ page 79).
• The screen will return to its previous state if the AV receiver is
operated.
Listening mode buttons
1
Press Receiver followed by an Input Selector
button.
En-25
Turning On & Basic Operations
Controlling Contents of USB or
Network Devices
Press USB or NET first.
a Top Menu
This button displays the top menu for each media or service.
n 2
This button stops playback.
b q/w and Enter
These buttons navigate through the menus.
o Mode
You can switch between Standard Mode and Extended Mode
(iPod/iPhone).
e/r
This button cycles through pages.
h
Playlist e/r
In Standard Mode (iPod/iPhone), this button selects
playlists.
c 1
This button starts playback.
i
a
b
c
d
e
f
g
j
k
l
m
n
o
p
q
d 7
This button selects the beginning of the current song.
Pressing this button twice selects the previous song.
e 5
This button fast-reverses the current song.
f 3
This button pauses playback.
g Search
You can toggle between the playback screen and the list
screen during playback.
h Display
This button switches between song information during
playback.
Press this button while the list screen is displayed to return to
the playback screen.
i Album +/–
In Standard Mode (iPod/iPhone), this button selects albums.
j Menu
This button displays the menu of Internet radio services.
k Return
This button returns to the previous menu.
l 6
This button selects the next song.
m 4
This button fast-forwards the current song.
En-26
p Random
This button performs random playback.
q Repeat
Press this button repeatedly to cycle through the repeat
modes.
Tip
• See “Controlling Other Components” about the operation of
other components (➔ page 91).
Note
• The buttons you can use will differ depending on the devices and
media used for playback.
Turning On & Basic Operations
Understanding Icons on the Display
This section describes icons that appear on the AV
receiver’s display during media playback.
Icon
Playing an iPod/iPhone via USB
3
Press Mode repeatedly to switch to Extended Mode
(Music) or Extended Mode (Video).
The on-screen information appears only on a TV that
is connected to HDMI outputs.
A list of your iPod/iPhone model’s contents appears.
Pause
This section explains how to play music/video files on the
iPod/iPhone.
Compatible iPod/iPhone models
Made for:
iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic,
iPod nano (2nd, 3rd, 4th, 5th and 6th generation),
iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone
• If you want to operate using the iPod/iPhone or the remote
controller, press Mode repeatedly to switch to Standard
mode.
• When you disconnect the iPod/iPhone, the AV receiver
remembers the current mode. This means that if you
disconnect when in Extended Mode (Music), the AV
receiver will start in Extended Mode (Music) the next time
you connect the iPod/iPhone.
Fast Forward
1
Tip
Description
Folder
Track
Playback
Fast Reverse
Repeat One Track
Repeat Folder (USB Device)
Repeat
Shuffle
Shuffle Album (iPod/iPhone)
4
• You can also use the q/w, Enter and Tuning Mode
buttons on the front panel. Tuning Mode allows you to
switch modes.
• The same operation can be done by selecting “USB” in the
Home menu.
2
Connect the USB cable that comes with the
iPod/iPhone to the USB port on the front of the AV
receiver.
While reading the contents of your iPod/iPhone, the
message “Connecting...” appears on the AV
receiver’s display.
The USB indicator lights. It will flash if the AV
receiver cannot read the iPod/iPhone.
Tip
• When connecting your iPod/iPhone with a USB cable, we
recommend you use an official USB cable from Apple Inc.
En-27
Use q/w to select a folder, and then press Enter to
open it.
Tip
Tip
Artist
Album
Press USB repeatedly to select the “USB(Front)”
input.
5
Use q/w to select a music/video file, and press Enter
or 1 to start playback.
Note
• While the message “Connecting...” appears on the AV receiver’s
display, do not disconnect the USB cable supplied with your
iPod/iPhone or the USB device from the USB port.
• If you connect an iPod or iPhone to the USB port, no sound will
be output from the headphones jack.
Turning On & Basic Operations
Extended Mode (Music) Control
The music content information is displayed (lists are
displayed), and you can control the music content while
looking at the screen.
Top screen list:
Playlists, Artists, Albums, Genres, Songs, Composers,
Shuffle Songs, Now Playing.
Note
Playing a USB Device
Listening to vTuner Internet Radio
The on-screen information appears only on a TV that
is connected to HDMI outputs.
You need to connect the AV receiver to your home
network (➔ page 115). The on-screen information
appears only on a TV that is connected to HDMI
outputs.
This section explains how to play music files from a USB
device (e.g., USB flash drives and MP3 players).
See also:
• “Network/USB Features” (➔ page 115).
• In this mode, video contents are not displayed, even if they are
input from the AUX Input Video jack on the AV receiver’s front
panel.
1
Press USB repeatedly to select the “USB(Front)” or
“USB(Rear)” input.
Extended Mode (Video) Control
2
The video content information is displayed (lists are
displayed), and you can control the video content while
looking at the screen.
Top screen list:
Movies, Music Videos, TV Shows, Video Podcasts,
Rentals.
Plug your USB device into the AV receiver’s USB
port.
The USB indicator lights. It will flash if the AV
receiver cannot read the USB device.
3
Press Enter.
A list of the device’s contents appears. To open a
folder, use q/w to select it, and then press Enter.
4
Use q/w to select a music file, and press Enter or
1 to start playback.
Note
• To view the video contents of your iPod/iPhone, connect it to the
USB port and AUX Input Video jack on the AV receiver’s front
panel, using the official Apple Composite AV Cable.
• Depending on your iPod/iPhone model and generation, the
displayed items may vary and the support for Extended Mode
(Video) is not guaranteed.
Note
The vTuner Internet Radio Service is a portal site featuring
radio stations from all over the world.
You can search for stations by categories such as genre or
location. The AV receiver is preinstalled with this service.
1
Press NET.
The network service screen appears, and the NET
indicator lights. If it flashes, verify that the Ethernet
cable is firmly connected to the AV receiver.
Tip
• The same operation can be done by selecting “Network
Service” in the Home menu.
2
Use q/w/e/r to select “vTuner Internet Radio”
and then press Enter.
3
Use q/w to select a program and then press Enter.
Playback starts.
• While the message “Connecting...” appears on the AV receiver’s
display, do not disconnect the USB cable supplied with your
iPod/iPhone or the USB device from the USB port.
Standard Mode Control
My Music
0 : 11
Great Artist
My Favorite
The content information is not displayed, but can be
operated using the iPod/iPhone or the remote controller.
Tip
• You can find stations similar to the one being played.
During playback, press Menu on the remote controller,
select “Stations like this” and press Enter.
En-28
Turning On & Basic Operations
■ Adding vTuner Internet Radio Stations to
Favorites
There are two ways you can register specific Internet
radio stations (programs) from the vTuner Internet
Radio.
Adding to My Favorites
The selected program will be added to “My Favorites”
on the network service screen, which appears when
pressing NET on the remote controller.
1. Press Menu with the station selected or while a
station is playing.
2. Use q/w to select “Add to My Favorites”, and press
Enter.
3. Use q/w/e/r to select “OK”, and press Enter.
Tip
• You can rename the stations saved in “My Favorites”.
Adding to vTuner Internet Radio’s Favorites
Select “vTuner Internet Radio” and press Enter to
display the “Favorites” folder that appears on the same
screen as “Stations By Genre”, “Stations By
Location”, etc. This is where your favorite Internet radio
bookmarks will be stored.
To register your favorite stations using a personal
computer, you need to connect your PC to the same
network as the AV receiver. Enter the ID# (MAC
address) of your unit on http://integra.vtuner.com/. You
can then register your favorite radio programs. The ID#
is shown at the bottom of the “vTuner Internet Radio”
top menu, and the AV receiver’s MAC address is shown
on “Network” of the Setup menu (➔ page 82).
Registering Other Internet Radio
You need to connect the AV receiver to your home
network (➔ page 115). The on-screen information
appears only on a TV that is connected to HDMI
outputs.
Internet radio URLs in the following formats are
supported: PLS, M3U, and podcast (RSS). However,
depending on the type of data or audio format used by the
Internet radio station, you may not be able to listen to some
stations.
To listen to other Internet radio stations, you must register
your station in “My Favorites” of the network service
screen, as described below.
Note
• Services available may vary depending on the region. See the
separate instructions for more information.
• Certain network service or contents available through this device
may not be accessible in case the service provider terminates its
service.
1
Select “Network” on the Setup menu to verify your
IP address (➔ page 82).
Take a note of the IP address.
2
3
On your computer, start your web browser.
4
Click on the “My Favorites” tab, and enter the
Internet radio station’s name and URL.
Enter the AV receiver’s IP address in the browser’s
Internet address (URL) field.
If you are using Internet Explorer®, you can also enter
the URL by selecting “Open...” on the “File” menu.
Information on the AV receiver is then shown on your
Internet browser (Web Setup).
En-29
5
Click “Save” to save the Internet radio station.
The Internet radio station is then added to “My
Favorites”. To play the registered station, press NET,
and then select “My Favorites” on the network
service screen. A list of registered Internet radio
stations appears. Select the one that you saved and
press Enter.
Tip
• If you want to add a new station directly from “My Favorites”,
select an empty slot in the list and press Menu. Then, select
“Create New Station” and press Enter.
Pressing Enter again will display the keyboard screen. Use that
keyboard to enter the station’s name and URL respectively, and
then press Enter.
• If you want to delete a station saved in “My Favorites”, press
Menu with the station selected or while the station is playing.
Then, use q/w to select “Delete from My Favorites” and press
Enter. You can also delete stations from the Web Setup.
• If you want to rename a station, select the desired station and
press Menu. Then, use q/w to select “Rename this station” and
press Enter.
• You can save up to 40 Internet radio stations.
Turning On & Basic Operations
Changing the Icon Layout on the
Network Service Screen
You need to connect your TV to the HDMI output
(HDMI OUT MAIN) to make the following on-screen
setting.
The layout of icons can be customized by switching their
positions on the network service screen.
1
Press NET.
The network service screen appears, and the NET
indicator lights. If it flashes, verify that the Ethernet
cable is firmly connected to the AV receiver.
Playing Music Files on a Server (DLNA)
4
1
2
Start your computer or media server.
• The same operation can be done by selecting “Network
Service” in the Home menu.
3
4
Note
• Depending on the media server, 5/4/3 may not
work.
• If the message “No Item.” appears, this means that no
information can be retrieved from the server. In this case,
check your server, network, and AV receiver connections.
Press NET.
The network service screen appears. The NET
indicator lights. If it flashes, confirm the network
connection.
Tip
Press Mode/D (blue) on the remote controller.
Use q/w/e/r to select another icon as the
destination, and then press Enter.
The icons switch positions and the message
“Completed!” appears.
My favorite song 1
0 : 11
Artist name
My favorite album
This section explains how to play music files on a
computer or media server through the AV receiver (Server
Playback).
Tip
Use q/w/e/r to select an icon to move, and then
press Enter.
Use q/w to select an item, and then press Enter or
1 to start playback.
You need to connect the AV receiver to your home
network (➔ page 115). The on-screen information
appears only on a TV that is connected to HDMI
outputs.
• The same operation can be done by selecting “Network
Service” in the Home menu.
2
3
5
Use q/w/e/r to select “DLNA”, and press Enter.
Use q/w to select a server, and then press Enter.
The menu is displayed according to the server
functions.
Note
• The search function does not work with media servers
which do not support this function.
• Photos and movies stored on a media server cannot be
accessed from the AV receiver.
• Depending on the sharing settings in the media server, the
AV receiver may not able to access the content. See the
instruction manual of the media server.
Windows Media Player 11 Setup
This section explains how to configure Windows Media
Player 11 so that the AV receiver can play the music files
stored on your computer.
1
2
Start Windows Media Player 11.
3
Select the “Share my media” check box, and then
click “OK”.
A list of the supported devices appears.
4
Select the AV receiver in the list, and then click
“Allow”.
The corresponding icon will be checked.
On the “Library” menu, select “Media Sharing”.
The “Media Sharing” dialog box appears.
To be continued
En-30
Turning On & Basic Operations
5
Click “OK” to close the dialog box.
This completes the Windows Media Player 11
configuration.
You can now play the music files in your Windows
Media Player 11 library through the AV receiver.
3
Move your cursor and click on “Turn on media
streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.
4
On the “Media streaming options”, select the AV
receiver and confirm that it is set to “Allow”.
5
Click “OK” to close the dialog box.
This completes the Windows Media Player 12
configuration.
You can now play the music files in your Windows
Media Player 12 library.
Tip
• Windows Media Player 11 can be downloaded for free from
the Microsoft web site.
Remote Playback
You need to connect the AV receiver to your home
network (➔ page 115). The on-screen information
appears only on a TV that is connected to HDMI
outputs.
Remote Playback means you can play the music files
stored on a media server or personal computer with the AV
receiver by operating the controller device in the home
network.
Tip
• On the “Stream” menu, confirm that “Allow remote control
of my Player...” is checked.
Using Remote Playback
1
2
Turn on the AV receiver.
3
On Windows Media Player 12, right-click on a
music file.
The right-click menu appears.
Windows Media Player 12 Setup
This section explains how to configure Windows Media
Player 12 so that the AV receiver can play the music files
stored on your personal computer.
1
2
Start Windows Media Player 12.
On the “Stream” menu, select “Turn on media
streaming”.
A dialog box appears.
Tip
• If the media streaming is already activated, clicking on
“More streaming options...” in the “Stream” menu will
display a list of the playback devices connected to the
network. You can skip step 3.
Start Windows Media Player 12.
To enable remote playback, you must first configure
Windows Media Player 12.
Tip
• For selecting another media server, select the desired media
server from the “Other Libraries” menu on Windows Media
Player 12.
4
Select the AV receiver in “Remote playback”.
The “Play to” window appears and playback on the
AV receiver starts. Operations during remote playback
can be made from the “Play to” window of Windows 7
on your personal computer.
A playback screen will be displayed on the connected
TV.
En-31
5
Adjusting the Volume.
You can adjust the volume by adjusting the volume
bar in the “Remote playback” window. The default
maximum volume level is 82 (0dB). If you wish to
change this, enter the value from the Web Setup in
your browser. Refer to step 3 of “Registering Other
Internet Radio” for details (➔ page 29).
The volume value of the remote window and the
volume value of the AV receiver may not always
match.
Adjustments you make to the volume in the AV
receiver will not be reflected in the “Remote
playback” window.
Note
• Remote playback cannot be used in any of the following cases:
– Network services are being used.
– Contents are being played from a USB device or iPod/iPhone.
– Zones are turned on.
Turning On & Basic Operations
■ Creating a shared folder
Playing music files on a shared folder
Right-click the folder that you want to share.
In order to enjoy Home Media, you must first create a
shared folder on your computer.
■ Setting the sharing options
1
2
3
4
1
5
Under “Network File and Folder Sharing”, select
“Share”.
Playing Music Files on a Shared Folder
This section explains how to play music files on a
computer or NAS (Network Attached Storage) through the
AV receiver.
Windows 7 Setup
Select “Choose homegroup and sharing options” on
the Control Panel.
Tip
• If this option is not available, verify that “View by:” is set to
“Category”.
2
3
4
Select “Change advanced sharing settings”.
Under “Home or Work”, verify that the following
items are checked:
“Turn on network discovery”, “Turn on file and
printer sharing”, “Turn on sharing so anyone with
network access can read and write files in the Public
folders”, and “Turn off password protected sharing”.
6
Select “Properties”.
On the “Sharing” tab, select “Advanced Sharing”.
1
Check the check box of “Share this folder” and then
click “OK”.
Select and add “Everyone” from the pull-down
menu and then click “Share”.
Tip
• The same operation can be done by selecting “Network
Service” in the Home menu.
2
Use q/w/e/r to select “Home Media”, and press
Enter.
3
Use q/w to select a server, and then press Enter.
Tip
• With this setting, everyone is allowed to access the folder.
If you want to assign a user name and password to the
folder, make the corresponding settings for “Permissions”
in “Advanced Sharing” of the “Sharing” tab.
• Verify that “Workgroup” is properly set.
Note
• When using NAS (Network Attached Storage), refer to the
instruction manual provided with your NAS unit.
Select “Save changes” and click “OK” on the
confirmation screen.
On the remote controller, press Receiver followed
by NET.
The network service screen appears. The NET
indicator lights. If it flashes, confirm the network
connection.
Tip
• The server name of your computer can be viewed on the
computer properties screen.
4
Use q/w to select the desired shared folder and then
press Enter.
5
When asked for a user name and password, enter
the necessary login information.
Tip
• The login information will be remembered for the next time
you log in.
• The login information is that of the user account set when
creating a shared folder.
6
En-32
Use q/w to select a music file and then press Enter
or 1.
The playback of the selected file starts.
Turning On & Basic Operations
Listening to AM/FM Radio
This section describes the procedure of using the
buttons on the front panel, unless otherwise specified.
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets for
quick selection.
You can also change the frequency steps (➔ page 80).
1
■ Auto tuning mode
■ Tuning into stations by frequency
You can tune into AM and FM stations directly by entering
the appropriate frequency.
1
Press Tuning Mode so that the AUTO indicator
lights on the AV receiver’s display.
1
2
Press Tuning q/w.
Searching stops when a station is found.
Tuning into Radio Stations
When tuned into a station, the TUNED indicator
lights. When tuned into a stereo FM station, the FM
STEREO indicator lights as shown.
Press Tuner to select either “AM” or “FM”.
In this example, FM has been selected.
Each time you press Tuner, the radio band changes
between AM and FM.
Band
On the remote controller, press Tuner repeatedly
to select “AM” or “FM”, followed by D.TUN.
(Actual display depends on the country.)
2
TUNED
AUTO
Within 8 seconds, use the number buttons to enter
the frequency of the radio station.
For example, to tune to 87.5 (FM), press 8, 7, 5 or 8,
7, 5, 0.
If you have entered the wrong number, you can retry
after 8 seconds.
Frequency
FM STEREO
Tip
• Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
manual tuning mode and listen to the station in mono.
(Actual display depends on the country.)
Note
• (North American models) When using the Whole House Mode
with “TUNER” input selector, connect antennas to both the
MAIN and ZONE 2 ANTENNA jacks/terminals (➔ pages 20,
51, 86).
■ Manual tuning mode
In manual tuning mode, FM stations will be in mono.
1
Press Tuning Mode so that the AUTO indicator
goes off on the AV receiver’s display.
2
Press and hold Tuning q/w.
The frequency stops changing when you release the
button.
Press the buttons repeatedly to change the frequency
one step at a time.
Presetting AM/FM Stations
You can store a combination of up to 40 of your favorite
AM/FM radio stations as presets.
1
Tune into the AM/FM station that you want to store
as a preset.
See the previous section.
2
Press Memory.
The preset number flashes.
(Actual display depends on the country.)
3
While the preset number is flashing (about 8
seconds), use Preset e/r to select a preset from 1
through 40.
To be continued
En-33
Turning On & Basic Operations
4
Press Memory again to store the station or channel.
The station or channel is stored and the preset number
stops flashing.
Repeat this procedure for all of your favorite AM/FM
radio stations.
■ Selecting Presets
1
To select a preset, use Preset e/r on the AV
receiver, or the remote controller’s CH +/–.
Listening to HD Radio™ Stations (North
American models)
HD Radio technology brings digital radio to conventional
analog AM and FM radio stations, with improved sound
quality, better reception, and new data services. HD Radio
technology provides CD-quality sound for FM stations,
and FM-quality sound for AM stations. In addition,
FM HD Radio stations can transmit multiple programs on
the same frequency by using multicast channels. Text data
display includes station name, song title, artist name, and
so on.
Tip
• You can also use the remote controller’s number buttons to
select a preset directly.
■ Deleting Presets
1
Select the preset that you want to delete.
See the previous section.
2
While holding down Memory, press Tuning Mode.
The preset is deleted and its number disappears from
the AV receiver’s display.
• Digital, CD-quality sound. HD Radio Technology
enables local radio stations to broadcast a clean digital
signal. AM sounds like today’s FM and FM sounds like a
CD.
• Program Service Data: Contributes to the superior user
experience of HD Radio Technology. Presents song
name, artist, station IDs, HD2/HD3 Channel Guide, and
other relevant data streams.
• Adjacent to traditional main stations are extra local FM
channels. These HD2/HD3 Channels provide new,
original music as well as deep cuts into traditional genre.
For more information about HD Radio technology, visit:
www.ibiquity.com
www.hdradio.com
■ About HD Radio Stations
HD Radio stations broadcast on the same AM and FM
frequencies they’ve always used, and you can receive them
by tuning into your favorite station as normal. If the current
En-34
AM or FM station supports HD Radio technology, the
HD Radio indicator lights up. When an HD Radio
transmission is received, the HD SPS indicator appears or
“HD Radio” appears on the display.
• If the current AM or FM station supports HD Radio
technology, the station’s name will be displayed instead
of the band and frequency.
• When music data is received, song title and artist name
information will be displayed next to the “HD” indicator.
• If the current HD Radio station supports multicast
channels, the currently selected multicast channel will be
displayed to the right of the “HD” indicator.
■ Selecting Multicast Channels
FM HD Radio stations can transmit multiple programs on
the same frequency by using what are called multicast
channes.
1
l
Press Tuner on the remote controller repeatedly to
select “FM” and use the e/r buttons to select
multicast channel.
If you select a multicast channel that is not currently
broadcasting, a plus “+” symbol or period “.” will
appear next to the “HD” indicator, indicating that the
channel has been reserved. When broadcasting
commences, that channel will be selected
automatically.
Reserved channel indication
HD Radio channel number
Note
• Multicast channels are not available on AM.
Turning On & Basic Operations
■ Setting the Blend Mode
HD Radio transmissions contain analog and digital signals.
If available, the digital signal is used automatically. In
areas with poor reception, you may want to choose the
analog signal.
1
l
■ Displaying HD Radio Information
Press the Display button repeatedly to cycle through the
available information.
HD Radio
channel number
Station name
Indicates HD Radio
reception
Scrolling title/artist
Press Enter repeatedly to select Auto or Analog.
HD channel, Artist name, and Song title are displayed in
the 2nd line if the AV receiver has a two-line display.
Frequency
Listening mode
Frequency &
Listening mode
Scrolling
station information
Note
• Multicast channels 2 through 8 are digital only, so you must select
multicast channel #1 before you can change the Blend mode.
RDS works only in areas where RDS broadcasts are
available.
When tuned into an RDS station, the RDS indicator lights.
When the station is broadcasting text information, the text
can be displayed.
Station name &
HD Radio
channel number
The options are:
`Auto:
Select to use the digital signal when available.
`Analog:
Select to use the analog signal.
Using RDS (excluding North American
models)
Station information
Scrolling
artist name
Artist information
Scrolling
song title
Song title
information
Note
• The exact information displayed depends on your AV receiver.
• This information is displayed only when receiving an HD Radio
signal.
En-35
■ What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed by
the European Broadcasting Union (EBU) and is available
in most European countries. Many FM stations use it these
days. In addition to displaying text information, RDS can
also help you find radio stations by type (e.g., news, sport,
rock, etc.).
The AV receiver supports four types of RDS information:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed. Pressing
Display will display the frequency for 3 seconds.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting text
information, the text will be shown on the AV receiver’s
display as described in the next section.
PTY (Program Type)
This allows you to search for RDS radio stations by type.
TP (Traffic Program)
This allows you to search for RDS radio stations that
broadcast traffic information (➔ page 36).
Turning On & Basic Operations
Note
• In some cases, the text characters displayed on the AV receiver
may not be identical to those broadcast by the radio station. Also,
unexpected characters may be displayed when unsupported
characters are received. This is not a malfunction.
• If the signal from an RDS station is weak, RDS data may be
displayed intermittently or not at all.
■ Listening to Traffic News (TP)
You can search for stations that broadcast traffic news.
1
■ Displaying Radio Text (RT)
1
Press RT/PTY/TP once.
The RT information scrolls across the AV receiver’s
display.
Note
• The message “Waiting” may appear while the AV receiver
waits for the RT information.
• If the message “No Text Data” appears, no RT information
is available.
2
3
4
Display
None
Press RT/PTY/TP three times.
If the current radio station is broadcasting TP (Traffic
Program), “[TP]” will appear on the AV receiver’s
display. If “TP” without square brackets appears, this
means that the station is not broadcasting TP.
News reports
News
To locate a station that is broadcasting TP, press
Enter.
The AV receiver searches until it finds a station that’s
broadcasting TP.
If no stations are found, the message “Not Found”
appears.
Drama
Drama
Culture
Culture
You can search for radio stations by type.
2
Type
None
■ Finding Stations by Type (PTY)
1
RDS program types (PTY)
Press RT/PTY/TP twice.
The current program type appears on the AV
receiver’s display.
Current affairs
Affairs
Information
Info
Sport
Sport
Education
Educate
Science and technology
Science
Varied
Varied
Pop music
Pop M
Rock music
Rock M
Middle of the road music
Easy M
Light classics
Light M
Serious classics
Classics
Other music
Other M
Weather
Weather
Finance
Finance
Children’s programmes
Children
Social affairs
Social
Religion
Religion
Phone in
Phone In
Travel
Travel
Use Preset e/r to select the type of program you
want.
See the table shown later in this chapter.
Leisure
Leisure
Jazz music
Jazz
Country music
Country
To start the search, press Enter.
The AV receiver searches until it finds a station of the
type you specified, at which point it stops briefly
before continuing with the search.
National music
Nation M
When a station you want to listen to is found, press
Enter.
If no stations are found, the message “Not Found”
appears.
En-36
Oldies music
Oldies
Folk music
Folk M
Documentary
Document
Alarm test
TEST
Alarm
Alarm!
Turning On & Basic Operations
Playing Audio and Video from Separate
Sources
You can listen to the audio of one input source while
watching the video of another. This function takes
advantage of the fact that when an audio-only input source
(BD/DVD, CBL/SAT, STB/DVR, Game 1, Game 2,
Tuner, TV/CD, Phono) is selected, the video input
source remains unchanged. The following procedure shows
how to listen to a CD player’s audio source connected to
TV/CD IN while watching a Blu-ray Disc/DVD player’s
video source connected to BD/DVD.
Tip
• To use an input selector as audio-exclusive, you must assign all
video inputs to “- - - - -” (➔ pages 60 to 62).
1
2
Press BD/DVD.
3
Start playback on your Blu-Ray Disc/DVD and CD
players.
You can now enjoy watching your Blu-ray Disc/DVD
with the sound of your CD player.
Press TV/CD.
The audio output changes to the CD source, but the
video of previously-selected BD/DVD is retained.
En-37
Turning On & Basic Operations
Using Basic Functions
Using the Automatic Speaker Setup
With the supplied calibrated microphone,
Audyssey MultEQ® XT32 automatically determines the
number of speakers connected, their size for purposes of
bass management, optimum crossover frequencies to the
subwoofer (if present), and distances from the primary
listening position.
Audyssey MultEQ XT32 then removes the distortion
caused by room acoustics by capturing room acoustical
problems over the listening area in both the frequency and
time domain. The result is clear, well-balanced sound for
everyone. Audyssey MultEQ XT32 can be used with
Audyssey Dynamic EQ® and
Audyssey Dynamic Volume® (➔ page 72).
Before using this function, connect and position all of your
speakers.
Audyssey MultEQ XT32 offers two ways of measuring:
the “Audyssey Quick Start” and
“Audyssey MultEQ XT32 Full Calibration”.
• “Audyssey Quick Start” uses the measurement from one
position to perform the speaker setting only.
• “Audyssey MultEQ XT32 Full Calibration” uses the
measurement from eight positions to correct room
response in addition to the speaker setting.
The more positions are used in measuring, the better the
listening environment will become. We recommend using
a measurement from eight positions to create the best
listening environment.
The Quick Start takes 2 minutes and Full Calibration takes
about 20 minutes.
Total measurement time varies depending on the number
of speakers.
Measurement procedure
To create a listening environment in your home theater that
all listeners will enjoy, Audyssey MultEQ XT32 takes
measurements at up to eight positions within the listening
area. Position the microphone at ear height of a seated
listener with the microphone tip pointed directly at the
ceiling using a tripod. Do not hold the microphone in your
hand during measurements as this will produce inaccurate
results.
■ First measurement position
Also referred to as the Main Listening Position, this
refers to the most central position where one would
normally sit within the listening environment.
Audyssey MultEQ XT32 uses the measurements from
this position to calculate speaker distance, level,
polarity, and the optimum crossover value for the
subwoofer.
■ Second-eighth measurement positions
These are the other listening positions (i.e., the places
where the other listeners will sit). You can measure up
to eight positions.
TV
def
cab
gh
: Listening area
a to h: Listening position
En-38
Note
• Make the room as quiet as possible. Background noise and Radio
Frequency Interference (RFI) can disrupt the room
measurements. Close windows, televisions, radios, air
conditioners, fluorescent lights, home appliances, light dimmers,
or other devices. Turn off the cell phone (even if it is not in use)
or place it away from all audio electronics.
• The microphone picks up test tones played through each speaker
as Audyssey MultEQ XT32 Room Correction and Speaker Setup
runs.
• Audyssey MultEQ XT32 Room Correction and Speaker Setup
cannot be performed while a pair of headphones is connected.
Turning On & Basic Operations
1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV receiver
is connected.
2
Set the speaker setup microphone at the Main
Listening Position a, and connect it to the Setup
Mic jack.
Setup Mic jack
If you use a powered subwoofer(s), go to step 4. If not,
go to step 5.
If “Speakers Type(Front)” is set to “Digital
Crossover”, a confirmation screen appears. Select
“Next (2-7. Digital Processing Crossover Network)”
to display the screen for Digital Processing Crossover
Network (➔ page 67). Continue with the settings.
4
Speaker setup microphone
The speaker setting menu appears.
Note
• The on-screen menus appear only on a TV that is connected
to HDMI OUT MAIN. If your TV is connected to other
video outputs, use the AV receiver’s display when changing
settings.
3
Note
MultEQ XT32: Auto Setup
AUDYSSEY
Normal
No
No
No
No
No
Perform the “Speaker Setup” according to your
speaker configuration:
5
Press Enter.
Audyssey MultEQ® XT32 Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ XT32 Room Correction and
Speaker Setup runs. This process takes a few minutes.
Please refrain from talking during measurements
and do not stand between speakers and the
microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ XT32 Room Correction and
Speaker Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 9.
7
Place the speaker setup microphone at the next
position, and then press Enter.
Audyssey MultEQ XT32 performs more
measurements. This takes a few minutes.
8
When prompted, repeat step 7.
To be continued
• If your subwoofer does not have a volume control, disregard
the displayed level and press Enter to proceed to the next
step.
• If you set the subwoofer’s volume control to its maximum
and the level displayed is lower than 75 dB, leave the
subwoofer’s volume control at its maximum and press
Enter to proceed to the next step.
• If you use two subwoofers, perform this step twice.
When you’ve finished making the settings, press
Enter.
Speakers Type(Front)
Passive Subwoofer
Powered Zone 2
Powered Zone 3
Powered Zone 4
11ch Playback
Adjust the subwoofer volume level to 75 dB, and
then press Enter.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
When the “Subwoofer” setting is set to “1ch” only,
the left-hand subwoofer (SW1) will be measured.
When the “Subwoofer” setting is set to “1ch” with
two subwoofers connected, the right-hand subwoofer
(SW2) will not be measured and no sound will be
output.
An error will occur if you set “Subwoofer” to “2ch”
without connecting any subwoofers, or with only one
subwoofer connected.
6
Use q/w to select “Audyssey Quick Start” or
“Audyssey MultEQ XT32 Full Calibration”, and
then press Enter.
– Speakers Type(Front) (➔ page 63)
– Passive Subwoofer (➔ page 63)
– Powered Zone 2 (➔ page 63)
– Powered Zone 3 (➔ page 63)
– Powered Zone 4 (➔ page 63)
– 11ch Playback (➔ page 63)
– Subwoofer (➔ page 64)
En-39
Turning On & Basic Operations
9
Use q/w to select an option, and then press Enter.
10
MultEQ XT32: Auto Setup
AUDYSSEY
-- Review Speaker Configuration -Subwoofer
Front
Center
Surround
Front Wide
Front High
Surround Back
Surround Back Ch
2ch
40Hz
40Hz
100Hz
None
100Hz
120Hz
2ch
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using e/r.
Error Messages
While Audyssey MultEQ XT32 Room Correction and
Speaker Setup is in progress, one of the error messages
below may appear.
MultEQ XT32: Auto Setup
AUDYSSEY
Note
Ambient noise is too high.
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.
Save
Cancel
The options are:
`Save:
Save the calculated settings and exit
Audyssey MultEQ® XT32 Room Correction and
Speaker Setup.
`Cancel:
Cancel Audyssey MultEQ XT32 Room
Correction and Speaker Setup.
Use q/w to select a target, and use e/r to change
the setting.
After the results of Audyssey MultEQ XT32 have
been saved, the menu will display the “Audyssey”
(➔ page 72), “Dynamic EQ” (➔ page 72),
“Dynamic Volume” (➔ page 72) settings.
11
12
Press Enter.
Retry
Cancel
Disconnect the speaker setup microphone.
Note
• You can cancel Audyssey MultEQ XT32 Room Correction and
Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ XT32 Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ XT32 Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ XT32 Room
Correction and Speaker Setup requires you run
Audyssey MultEQ XT32 Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.
Error message
The options are:
`Retry:
Try again.
`Cancel:
Cancel Audyssey MultEQ XT32 Room Correction
and Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the source of
the noise and try again.
• Speaker Matching Error!
The number of speakers detected was different from that
of the first measurement. Check the speaker connection.
• Writing Error!
This message appears if saving fails. Try saving again. If
this message appears after 2 or 3 attempts, contact the
dealer from whom you purchased this unit.
• Speaker Detect Error
This message appears if a speaker is not detected. “No”
means that no speaker was detected.
Tip
• See “Speaker Configuration” for appropriate settings
(➔ page 11).
En-40
Turning On & Basic Operations
Changing the Speaker Setup Manually
You can manually make changes to the settings found
during Audyssey MultEQ® XT32 Room Correction and
Speaker Setup.
See also:
• “Speaker Configuration” (➔ page 64)
• “Speaker Distance” (➔ page 65)
• “Level Calibration” (➔ page 65)
• “Equalizer Settings” (➔ page 66)
Using the Listening Modes
Selecting Listening Modes
See “About Listening Modes” for detailed information
about the listening modes (➔ page 42).
■ Listening Mode Buttons
Press Receiver first.
Note
• Please note that THX recommends any THX main speakers be set
to “80Hz(THX)”. If you set up your speakers using
Audyssey MultEQ XT32 Room Correction and Speaker Setup,
please make sure manually that any THX speakers are set to
“80Hz(THX)” crossover (➔ page 64).
• Sometimes due to the electrical complexities of subwoofers and
the interaction with the room, THX recommends setting the level
and the distance of the subwoofer manually.
• Sometimes due to interaction with the room, you may notice
irregular results when setting the level and/or distance of the main
speakers. If this happens, THX recommends setting them
manually.
• The Dolby Digital and DTS listening modes can only be
selected if your Blu-ray Disc/DVD player is connected to
the AV receiver with a digital audio connection (coaxial,
optical, or HDMI).
• The listening modes you can select depends on the format
of the input signal. To check the format, see “Displaying
Source Information” (➔ page 50).
• While a pair of headphones is connected, you can select the
following listening modes: Mono, Direct, and Stereo.
Music
Movie/TV
Game
THX
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by Audyssey MultEQ XT32 Room Correction
and Speaker Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the subwoofer’s
volume to the half-way point, set it to its highest crossover
frequency, and then try running Audyssey MultEQ XT32
Room Correction and Speaker Setup again. Note that if the
volume is set too high and the sound distorts, detection
issues may occur, so use an appropriate volume level. If the
subwoofer has a low-pass filter switch, set it to Off or
Direct. Refer to your subwoofer’s instruction manual for
details.
Movie/TV button
This button selects the listening modes intended for use
with movies and TV.
Music button
This button selects the listening modes intended for use
with music.
Game button
This button selects the listening modes intended for use
with video games.
THX button
This button selects the THX listening modes.
Movie/TV, Music, Game
En-41
Turning On & Basic Operations
About Listening Modes
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall, with
high fidelity and stunning surround sound.
SP (speaker layout)
■ Explanatory Notes
ab
c ij
Speaker Layout
The illustration shows which speakers are activated in each
channel. See “Speaker Configuration” for the speaker setup
(➔ page 64).
z
kl f
Listening mode buttons
Input Source
The following audio formats are supported by the listening
modes.
de gh
a b Front speakers
c Center speaker
d e Surround speakers
f Subwoofer(s)
g h Surround back speakers
i j Front high speakers
k l Front wide speakers
A
This is mono (monophonic) sound.
S
This is stereo (stereophonic) sound. Two
independent audio signal channels are reproduced
through two speakers.
D
This is 5.1-channel surround sound. This surround
system has five main channels of sound and a sixth
subwoofer channel (called the point-one channel).
F
This is 7.1-channel surround sound. This is a
further sound enhancement to 5.1-channel sound
with two additional speakers that provide greater
sound envelopment and more accurate positioning
of sounds.
G
This is DTS-ES surround sound. This surround
system can produce a discrete or a matrix-encoded
sixth channel from existing DTS 5.1 encoded
material.
H
This is Dolby Digital EX surround sound. This
provides a center back surround channel from 5.1channel sources.
En-42
x
c
Turning On & Basic Operations
n
.
m*1
+
/
*
,
}
v*2
*1
*2
After enabling the corresponding speakers, press Receiver
followed by SP (speaker layout) repeatedly to select the
speakers you want to use: surround back and front
high,surround back and front wide, or front high and front
wide.
This layout is only available when the external power amplifier
is connected to FRONT WIDE PRE OUT of the AV receiver
and the “11ch Playback” setting is set to “Yes” (➔ page 12,
63).
En-43
Turning On & Basic Operations
■ Onkyo-Original DSP Listening Modes
Listening Mode
Description
Orchestra
Suitable for classical or operatic music, this
mode emphasizes the surround channels in
order to widen the stereo image, and
simulates the natural reverberation of a large
hall.
Or ches t r a
Unplugged
Un p l u g g e d
Studio-Mix
S t u d i o –M i x
TV Logic
TV
Log i c
Game-RPG
G ame – RPG
Game-Action
G ame – A c t i o n
Game-Rock
G ame – R o c k
Game-Sports
G ame – S p o r t s
Input
Source
Speaker
Layout
A cnm
S v
D
F
G
Suitable for acoustic instruments, vocals and H
jazz, this mode emphasizes the front stereo
image, giving the impression of being right
in front of the stage.
Suitable for rock or pop music, listening to
music in this mode creates a lively sound
field with a powerful acoustic image, like
being at a club or rock concert.
Listening Mode
Description
All Ch Stereo
Ideal for background music, this mode fills A xcn
the entire listening area with stereo sound
S mv
from the front, surround, and surround back D
speakers.
F
In this mode, all speakers output the same
G
sound in mono, so the sound you hear is the H
same regardless of where you are within the
listening room.
A l l
Ch
S t e r eo
Full Mono
Fu l l
Mo n o
T-D (TheaterDimensional)
T–D
This mode adds realistic acoustics to TV
shows produced in a TV studio, surround
effects to the entire sound, and clarity to
voices.
In this mode, the sound has a dramatic feel
with a similar atmosphere to Orchestra
mode.
In this mode, sound localization is distinct
with emphasis on bass.
In this mode, sound pressure is emphasized
to heighten live feel.
In this mode, reverberation is increased and
sound localization decreased slightly.
En-44
With this mode you can enjoy a virtual
surround sound even with only two or three
speakers. This works by controlling how
sounds reach the listener’s left and right ears.
Good results may not be possible if there’s
too much reverb, so we recommend that you
use this mode in an environment with little
or no natural reverb.
Input
Source
Speaker
Layout
zxc
nmv
Turning On & Basic Operations
■ Listening Modes
Listening Mode
Description
Direct
In this mode, audio from the input source is
output without surround-sound processing.
The speaker configuration (presence of
speakers) and speaker distance settings are
enabled, but much of the processing set via
the audio setup is disabled. See “On-screen
Setup” for more details (➔ page 53).
A zxc
S n*1m
D v
F
G
H
Sound is output from the front left and right
speakers and subwoofer.
zxc
nmv
D i r ec t
Stereo
S t e r eo
Mono
Multichannel
Mu l t i c h
DSD*2
DSD
Dolby Digital
D
Dolby Digital Plus*3
Do l b y
Speaker
Layout
D
+
Do l b y
T r u e HD
Description
DTS
In this mode, audio from the input source is D xcn
output without surround-sound processing.
mv
The speaker configuration (presence of
speakers), crossover frequency, speaker
D xcn
distance, A/V Sync and much of the
mv
processing set via the audio setup are
F xcn*1
enabled. See “On-screen Setup” for more
mv
details (➔ page 53).
D xcn
mv
DTS
D T S – HD
HR
DTS-HD Master
Audio
DTS Express
D xcn
mv
Exp r ess
DTS
96 / 24
This mode is for use with PCM multichannel D xcn
sources.
F mv
DTS-ES Discrete*5
ES
D xcn
mv
Speaker
Layout
F xcn*1
mv
DTS
In this mode, audio from the input source is D xcn
output without surround-sound processing.
mv
The speaker configuration (presence of
speakers), crossover frequency, speaker
distance, A/V Sync and much of the
processing set via the audio setup are
D xcn
enabled. See “On-screen Setup” for more
details (➔ page 53).
mv
Input
Source
D T S – HD MS T R
DTS 96/24*4
F xcn*1
mv
Dolby TrueHD
Listening Mode
DTS-HD High
Resolution Audio
Use this mode when watching an old movie
with a mono soundtrack, or use it with the
foreign language soundtracks recorded in the
left and right channels of some movies. It
can also be used with DVDs or other sources
containing multiplexed audio, such as
karaoke DVDs.
Mo n o
Do l b y
Input
Source
D i sc r e t e
DTS-ES Matrix*5
ES Ma t r i x
F xcn*1
mv
En-45
This mode is for use with DTS 96/24
sources. This is high-resolution DTS with a
96 kHz sampling rate and 24-bit resolution,
providing superior fidelity. Use it with
DVDs that bear the DTS 96/24 logo.
D xcn
mv
This mode is for use with DTS-ES Discrete G ,
soundtracks, which use a discrete surround
+
back channel for true 6.1/7.1-channel
*
playback. The seven totally separate audio
v
channels provide better spatial imaging and
360-degree sound localization, perfect for
sounds that pan across the surround
channels. Use it with DVDs that bear the
DTS-ES logo, especially those with a DTSES Discrete soundtrack.
This mode is for use with DTS-ES Matrix
soundtracks, which use a matrix-encoded
back-channel for 6.1/7.1-channel playback.
Use it with DVDs that bear the DTS-ES
logo, especially those with a DTS-ES Matrix
soundtrack.
Turning On & Basic Operations
Listening Mode
Description
Input
Source
Speaker
Layout
Dolby Pro Logic IIx*6 Dolby Pro Logic IIx expands any 2-channel
source for 7.1-channel playback. It provides
Dolby Pro Logic II
a very natural and seamless surround-sound
PL
Mo v i e
experience that fully envelops the listener.
As well as music and movies, video games
PL
Mu s i c
can also benefit from the dramatic spatial
effects and vivid imaging.
PL
Game
PL
x
Mo v i e
PL
x
Mu s i c
PL
x
Game
Dolby Pro Logic IIz
Height
PL
z
He i g h t
Dolby EX
Do l b y
EX
Do l b y
D
EX
If you’re not using any surround back
S xcn
speakers, Dolby Pro Logic II will be used
mv
instead of Dolby Pro Logic IIx.
• Dolby PLIIx Movie
Use this mode with any stereo or Dolby
Surround (Pro Logic) movie (e.g., TV,
DVD, VHS).
• Dolby PLIIx Music
Use this mode with any stereo or Dolby
Surround (Pro Logic) music source (e.g.,
CD, radio, cassette, TV, VHS, DVD).
• Dolby PLIIx Game
Use this mode with video games, especially
those that bear the Dolby Pro Logic II logo.
• Dolby PLIIx Movie
• Dolby PLIIx Music
These modes use the Dolby Pro Logic IIx
modes to expand 5.1-channel sources for
7.1-channel playback.
D ,
H +
*
v
Dolby Pro Logic IIz Height is designed to
more effectively use existing program
material when height channel speaker
outputs are present. Dolby Pro Logic IIz
Height can be used to upmix a variety of
sources from movies and music, but are
particularly well-suited to upmix game
content.
S
D
F
G
H
Listening Mode
Description
DTS Neo:X*7
This mode expands various sources and
various inputs up to 11.1 channel.
DTS Neo:X provides semi-spherical sound
field adding height/wide speakers to create a
natural, immersive and spacious surround
soundscape.
Ne o : X
6
C i n ema
Ne o : X
Mu s i c
Ne o : X
Game
Audyssey DSX*8
Audy s s e y
.
+
}
v
These modes expand 5.1-channel sources for D ,
6.1/7.1-channel playback. They’re especially H +
suited to Dolby EX soundtracks that include
*
a matrix-encoded surround back channel.
v
The additional channel adds an extra
dimension and provides an enveloping
surround sound experience, perfect for
rotating and fly-by sound effects.
En-46
DSX
Input
Source
Speaker
Layout
• DTS Neo:X Cinema
This mode is suitable for movie viewing.
• DTS Neo:X Music
This mode is suitable for any music source.
• DTS Neo:X Game
This mode is suitable for video games.
S xcn
D mv
F
G
H
• Audyssey DSX
Audyssey DSX® is a scalable system that
adds new speakers to improve surround
impression. Starting with a 5.1 system
Audyssey DSX first adds Wide channels
for the biggest impact on envelopment.
Research in human hearing has proven that
information from the Wide channels is
much more critical in the presentation of a
realistic soundstage than Back Surround
channels found in traditional 7.1 systems.
Audyssey DSX then creates a pair of
Height channels to reproduce the next most
important acoustical and perceptual cues.
In addition to these new Wide and Height
channels, Audyssey DSX applies Surround
Envelopment Processing to enhance the
blend between the front and surround
channels.
D .
F /m
G v
H
Turning On & Basic Operations
Listening Mode
PL
PL
PL
PL
PL
PL
Input
Source
Speaker
Layout
• Dolby Pro Logic II/IIx*6 Movie +
S .
Audyssey DSX
/m
• Dolby Pro Logic II/IIx*6 Music +
v
Mu s i c DSX
Audyssey DSX
• Dolby Pro Logic II/IIx*6 Game +
Game DSX
Audyssey DSX
The combination of Dolby Pro Logic II/IIx
and Audyssey DSX® modes can be used.
x Mo v i e DSX
• Dolby Pro Logic IIx Movie +
D +
x Mu s i c DSX
Audyssey DSX
H *
• Dolby Pro Logic IIx Music +
v
Audyssey DSX
x Game DSX
The combination of Dolby Pro Logic IIx
and Audyssey DSX modes can be used.
Mo v i e
Do l b y
THX
Description
EX
DSX
DSX
• Dolby EX + Audyssey DSX
The combination of Dolby EX and
Audyssey DSX modes can be used.
Listening Mode
THX
C i n ema
N
TH
eX
o :M
6us i c
THX
D +
H *
v
Founded by George Lucas, THX develops
stringent standards that ensure movies are
reproduced in movie theaters and home
theaters just as the director intended. THX
Modes carefully optimize the tonal and
spatial characteristics of the soundtrack for
reproduction in the home-theater
environment. They can be used with 2channel matrixed and multichannel sources.
Surround back speaker output depends on
the source material and the selected listening
mode.
Game s
Description
Input
Source
Speaker
Layout
• THX Cinema
THX Cinema mode corrects theatrical
soundtracks for playback in a home theater
environment. In this mode, THX Loudness
Plus is configured for cinema levels and
Re-EQ, Timbre Matching, and Adaptive
Decorrelation are active.
• THX Music
THX Music mode is tailored for listening to
music, which is typically mastered at
significantly higher levels than movies. In
this mode, THX Loudness Plus is
configured for music playback and only
Timbre Matching is active.
• THX Games
THX Games mode is meant for spatially
accurate playback of game audio, which is
often mixed similarly to movies but in a
smaller environment. THX Loudness Plus
is configured for game audio levels, with
Timbre Matching active.
D cnm
F v
G
H
• Dolby Pro Logic II/IIx*6 Movie + THX S cnm
Cinema
v
• Dolby Pro Logic II/IIx*6 Music + THX
Music
• Dolby Pro Logic II/IIx*6 Game + THX
Games
The combination of Dolby Pro Logic II/IIx
and THX Cinema/Music/Games modes can
be used.
The PLII/PLIIx and THX indicators light
on the AV receiver’s display.
• Dolby Pro Logic IIx Movie + THX
D ,
Cinema
H +
• Dolby Pro Logic IIx Music + THX Music
*
The combination of Dolby Pro Logic IIx
v
and THX Cinema/Music modes can be
used.
The PLIIx and THX indicators light on the
AV receiver’s display.
En-47
Turning On & Basic Operations
Listening Mode
Description
Input
Source
Speaker
Layout
• Dolby Pro Logic IIz Height + THX
Cinema
• Dolby Pro Logic IIz Height + THX
Music
• Dolby Pro Logic IIz Height + THX
Games
The combination of Dolby Pro Logic IIz
Height and THX Cinema/Music/Games
modes can be used.
The PLIIz and THX indicators light on the
AV receiver’s display.
S
D
F
G
H
.
+
}
v
• DTS Neo:X Cinema + THX Cinema
• DTS Neo:X Music + THX Music
• DTS Neo:X Game + THX Games
The combination of DTS Neo:X
Cinema/Music/Game and THX Cinema/
Music/Games modes can be used. The
Neo:X indicator lights on the AV
receiver’s display.
TH
N
eX
o : U
62
C i n ema
THX
U2
Mu s i c
THX
U2
Game s
THX
Su r r
EX
Listening Mode
Description
Input
Source
Speaker
Layout
• Dolby Pro Logic II Game + THX Ultra2 S ,
Games
+
The combination of Dolby Pro Logic II
*
Game and THX Ultra2 Cinema modes can
v
be used. The PLII and THX indicators
light on the AV receiver’s display.
• Dolby Pro Logic IIz Height + THX
S +
Ultra2 Games
D v
The combination of Dolby Pro Logic IIz
H
Height and THX Ultra2 Games modes can
be used.
nmv
• THX Ultra2 Cinema
D ,
This mode expands 5.1-channel sources for H +
7.1- channel playback. It does this by
*
analyzing the composition of the surround
v
source, optimizing the ambient and
directional sounds to produce the surround
back channel output.
• THX Ultra2 Music
This mode is designed for use with music.
It expands 5.1-channel sources for 7.1channel playback.
• THX Ultra2 Games
This mode is designed for use with video
games. It can expand 5.1-channel sources
for 6.1/7.1-channel playback.
• Dolby Pro Logic IIz Height + THX
Ultra2 Cinema
• Dolby Pro Logic IIz Height + THX
Ultra2 Music
The combination of Dolby Pro Logic IIz
Height and THX Ultra2 Cinema/Music
modes can be used.
D +
H v
Note
*1
Based on the audio channel signal contained in the source, the corresponding speakers will output
the sound.
*2 The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the
output on the player side to PCM might bring better sound.
*3 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.
*4 DTS is used depending on the configuration of the AV receiver.
*5 If there are no surround back speakers, DTS is used.
*6 If there are no surround back speakers, Dolby Pro Logic II is used.
*7 DTS Neo:X cannot be selected in the case of 192 kHz input signals.
*8 This listening mode can be selected only when all the following conditions are satisfied:
– Center speaker is connected.
– Either the front high or front wide speakers are connected.
• The listening modes cannot be selected with some source formats.
• THX Surround EX
This mode expands 5.1-channel sources for
6.1/7.1- channel playback. It’s especially
suited to Dolby Digital EX sources. THX
Surround EX, also known as Dolby Digital
Surround EX, is a joint development
between Dolby Laboratories and THX Ltd.
En-48
Turning On & Basic Operations
Using the Home Menu
The Home menu provides quick access to frequently used
menus.
The Home menu appears only on a TV that is
connected to HDMI OUT MAIN. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
1
Press Receiver followed by Home.
The Home menu will be superimposed on the TV
screen.
Enter again switches to that selection. If you want to
play music files on a server, use q/w/e/r to select
“DLNA” and then press Enter.
■ USB
` With this selection, you can play contents of portable
players (iPod, etc.) and USB storage devices connected
to the AV receiver’s USB port (➔ pages 27, 28).
Note that this selection will be grayed out for a short
while after the AV receiver is turned on. Please wait
until it becomes operable.
First, press USB repeatedly to select the
“USB(Front)” or “USB(Rear)” input.
Then, press Enter to select a drive or browse the
contents of the media connected, followed by q/w to
select the desired folder or track. Pressing Enter as a
track is selected will start playback.
Note
• Only the front-panel USB input is compatible with iPod/iPhone.
2
Use e/r or q/w and Enter to make the desired
selection.
Press Home to close the menu.
■ Network Service
You need to connect the AV receiver to your home
network (➔ page 115).
` With this selection, you can use various Internet radio
services or play the contents stored in media connected
to your home network (DLNA) (➔ pages 28 to 32).
Note that this selection will be grayed out for a short
while after the AV receiver is turned on. Please wait
until it becomes operable.
Press Enter to display the network service screen. If
you want to use the Internet radio services, use
q/w/e/r to select the desired service. Pressing
■ InstaPrevue
` With this selection, you can preview audio/video
streams coming from HDMI inputs (HDMI
IN 1/2/3/4/AUX Input). Even with multiple
components connected through HDMI, you can easily
switch between inputs as their previews are displayed
on a single screen.
Press Enter to display the main preview (currently
selected HDMI input) and the additional previews
(other HDMI inputs). Using q/w or e/r to select a
preview thumbnail and pressing Enter will switch
the AV receiver to that input source.
En-49
Tip
• If no video signals are present, the thumbnails will be filled in
black.
• You can specify the number of preview thumbnails as well as
their positioning on screen (➔ page 81).
Note
• This function cannot be selected when:
– HDMI IN 5/6/7/8 is the current HDMI input source, or
– No signal is present on the current input source, or
– The “Zone 2 HDMI” setting is set to “Use” (➔ page 59).
• Depending on video signals, the picture may not be properly
rendered on the preview thumbnails of InstaPrevue.
■ Setup
`With this selection, you can access the common
settings of the on-screen Setup menu.
Press Enter to display the Setup menu (➔ page 57).
Tip
• You can also access frequently used settings from Quick
Setup (➔ page 53).
■ Firmware Update
`With this selection, you can update the firmware of the
AV receiver. Note that this selection will be grayed out
for a short while after the AV receiver is turned on.
Please wait until it becomes operable.
Press Enter to start the procedure (➔ page 104).
Turning On & Basic Operations
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
You can display various information about the current
input source as follows.
1
1
Press Receiver once followed by Sleep repeatedly
to select the required sleep time.
The sleep time can be set from 90 to 10 minutes in 10
minute steps.
The SLEEP indicator lights on the AV receiver’s
display when the sleep timer has been set. The
specified sleep time appears for about 5 seconds, then
the previous display reappears.
Press Receiver once followed by Display
repeatedly to cycle through the available
information.
Tip
The following information can be typically displayed.
Input source
Listening mode
• If you need to cancel the sleep timer, press Sleep
repeatedly until the SLEEP indicator goes off.
• To check the time remaining until the AV receiver sleeps,
press Sleep. Note that if you press again on Sleep as the
time being displayed is 10 minutes or less, the sleep timer
will go off.
Signal format*1
Sampling
frequency
1
Press TV/CD or Game1.
“TV/CD” or “GAME1” appears on the AV receiver’s
display.
2
Press and hold down the same button (about
3 seconds) to change the input display.
Repeat this step to select the desired input display.
TV/CD → DOCK
TAPE
■ Game1:
GAME1 ↔ DOCK
Note
• “DOCK” can be selected for the “TV/CD”, “GAME1”
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (➔ page 93).
Output resolution
You can adjust the brightness of the AV receiver’s display.
*1
■ TV/CD:
“
Input signal
resolution
Setting the Display Brightness
Press Receiver once followed by Dimmer
repeatedly to switch between: normal, dim, or
dimmer brightness.
When you connect an u-capable Integra/Onkyo
component, you must configure the input display so that
u can work properly.
This setting can be done only from the front panel.
• Alternatively, you can use Display on the AV receiver.
Tip
1
Changing the Input Display
→
Displaying Source Information
→
Using the Sleep Timer
If the input signal is digital, the signal format is displayed.
Information is displayed for about three seconds, then the
previously displayed information reappears.
Tip
• (North American models) Alternatively, you can use
Dimmer on the AV receiver.
En-50
Turning On & Basic Operations
Using the Whole House Mode
The Whole House Mode is useful when you want to add
extra background music to your home party; this allows
you to enjoy the same stereo music as the main room in
separate rooms (Zone 2/3/4).
The Whole House Mode selects the same input source for
Multi Zone as the main room’s.
See also:
• “Speaker Setup” (➔ page 62)
• “Multi Zone” (➔ page 84)
1
Press Whole House Mode on the front panel.
To cancel the Whole House Mode, press Off, change
the input source for the main room, or select a
listening mode (➔ page 41).
Note
• (North American models) When using the Whole House
Mode with “TUNER” input selector, connect antennas to
both the MAIN and ZONE 2 ANTENNA jacks/terminals
(➔ pages 20, 86).
• The Whole House Mode only supports analog audio.
• To adjust the volume of Multi Zone, switch the AV receiver
to Multi Zone control. See “Adjusting the Volume for
Zones” (➔ page 86) for the volume adjustment of Multi
Zone.
• The Whole House Mode is not available in the following
cases:
– The “Audio TV Out” setting is set to “On”
(➔ page 81).
– “HDMI Control(RIHD)” is set to “On” (➔ page 80)
and you’re listening through your TV speakers.
– Digital Processing Crossover Network is used
(➔ page 67).
Selecting Speaker Layout
Muting the AV Receiver
You can set which speakers you want to use by priority.
You can temporarily mute the output of the AV receiver.
1
1
Press Receiver followed by SP (speaker layout)
repeatedly to select:
■ 9.2 ch playback
Press Receiver followed by Muting.
The output is muted and the MUTING indicator
flashes on the AV receiver’s display.
Tip
Important:
• The following layouts are only available when the “11ch
Playback” is set to “No” (➔ page 63) and all
corresponding speakers are enabled.
` Speaker Layout:SB/FH:
The sounds from surround back and front high
speakers are output by priority.
` Speaker Layout:SB/FW:
The sounds from surround back and front wide
speakers are output by priority.
` Speaker Layout:FH/FW:
The sounds from front high and front wide
speakers are output by priority.
Note
• This setting is not available in either of the following cases:
– The “Speakers Type(Front)” setting is set to “Bi-Amp”
or “Digital Crossover”.
– The “Passive Subwoofer” setting is set to “Yes”.
– The “Powered Zone 2/3/4” setting is set to “Yes” and
Zone 2/3/4 is turned on.
• Playback conditions may be limited depending on the settings in “Speaker Settings” (➔ page 63) and “Speaker
Configuration” (➔ page 64).
• When a listening mode which doesn’t support front high,
front wide or surround back speakers is used, this setting
cannot be selected.
En-51
• To unmute, press Muting again or adjust the volume.
• Muting is automatically cancelled when the AV receiver is
set to standby.
Turning On & Basic Operations
Using Headphones
1
Connect a pair of stereo headphones with a
standard plug (1/4 inch or 6.3 mm) to the Phones
jack.
While the headphones plug is inserted in the Phones
jack, = indicator, speaker/channel indicator FL and
FR lights.
Note
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the Phones jack,
the speakers are turned off. (The Zone 2/3/4 speakers are not
turned off.)
• When you connect a pair of headphones, the listening mode
is set to Stereo, unless it’s already set to Stereo, Mono, or
Direct.
• If you connect an iPod or iPhone to the USB port on the AV
receiver, no sound will be output from the headphones jack.
Using Easy Macros
By using Activities in Easy macro mode, you can
sequentially operate Integra/Onkyo components via simple
commands from a single-button press.
These commands are user-definable. See “Using Normal
Macros” (➔ page 97).
1
Press Activities (My Movie, My TV, or My Music)
to start the Easy macro command.
The default sequences of actions are described below.
To change the related source component, see
“Changing the Source Components” shown later in
this chapter.
■ My Movie
First, the TV, the Integra/Onkyo Blu-ray Disc player, and
the AV receiver are turned on. The input selector is set to
“BD/DVD”. Finally the player starts playback.*1
*1
Depending on the start-up time of your Blu-ray Disc/DVD
player, the AV receiver may not activate this playback
command. In this case, press 1 on the remote controller.
Changing the Source Components
You can change the source components activated by the
Easy Macro mode.
1
■ My TV
First, the TV, the cable set-top box, and the AV receiver
are turned on. Then the input selector is set to
“CBL/SAT”.
■ My Music
The Integra/Onkyo CD player and the AV receiver are
turned on. The input selector is set to “TV/CD”. Finally,
the player starts playback.
Note
• While the Easy Macro command is being processed, you cannot
use other Activities. If you want to operate other components,
first press All Off and use the desired Activities.
Turning Off the Components
This button turns off all components activated by the Easy
Macro mode.
1
Press All Off.
First, the related components stop and turn off. Second, the
AV receiver turns off. Finally, the TV turns off (or enters
standby mode).*1*2
*1
*2
This step doesn’t apply to My Music, with the default
settings.
With some televisions, the power may not be turned off (or
enter standby mode).
En-52
While holding down Remote Mode for the
playback component you wish to assign, press and
hold down the Activities to be changed
(My Movie, My TV, or My Music) (about 3
seconds).
Activities flashes twice, indicating that the change is
complete.
Examples:
If you wished to use My Music to start the Onkyo cassette
recorder, you would press and hold down My Music
(about 3 seconds) while holding down TV/CD until it
flashes twice.
Restoring Default
You can restore Activities to the default settings.
1
While holding down Home, press and hold down
All Off until All Off lights (about 3 seconds).
2
Release Home and All Off, and press All Off again.
All Off flashes twice.
Advanced Operations
On-screen Setup
Using the Quick Setup
With the AV receiver connected to a TV, there are two
ways of changing the settings on-screen: using the Quick
Setup or the Setup menu (Home).
■ Quick Setup
The Quick Setup provides quick access to frequently used
settings. You can change settings and view the current
information.
Receiver
Enter
q/w/e/r
■ Setup menu (Home)
The Setup menu (Home) provides a convenient way to
change the AV receiver’s various settings. Settings are
organized into 9 categories.
The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
Q Setup
Return
1
Press Receiver followed by Q Setup.
The Quick Setup will be superimposed on the TV
screen.
2
Use q/w and Enter to make the desired selection.
Press Q Setup to close the menu.
Press Return to return to the previous menu.
This section describes the procedure for using the
remote controller unless otherwise specified.
Explanatory Notes
a
b
■ Music Optimizer
` Off
` On
a Setting target
b Setting options (default setting underlined)
BD/DVD
Input
Audio
Video
Information
Listening Mode
En-53
■ Input
`You can select input sources and view the following
information: the name of input selectors, input
assignments, radio information, and ARC function
setting.
In addition, previews of the video streams coming from
HDMI inputs (HDMI IN 1/2/3/4/AUX Input) are
displayed.*1
Use q/w to select an input source and view the
related information. Pressing Enter switches to the
selected input source.
■ Audio (➔ page 54)
`You can change the following settings: “Sound
Program”, “Bass (Front)”, “Treble (Front)”, “Bass
(Front Wide)”, “Treble (Front Wide)”, “Bass (Front
High)”, “Treble (Front High)”, “Bass (Center)”,
“Treble (Center)”, “Bass (Surround)”, “Treble
(Surround)”, “Bass (Surround Back)”, “Treble
(Surround Back)”, “Bass (Subwoofer)”,
“Subwoofer 1”, “Subwoofer 2”, “Center”, “Dolby
Volume*2”, “Audyssey”, “Dynamic EQ*2*3”,
“Dynamic Volume*2*3”, “Late Night”, “Music
Optimizer”, “Re-EQ”, “Re-EQ(THX)” and “Screen
Centered Dialog”.
■ Video*4
`You can change the following settings: “Wide Mode”
and “Picture Mode*5”.
See also:
• “Picture Adjust” (➔ page 74)
■ Information*6
`You can view the information of the following items:
“Audio”, “Video” and “Tuner”.
Advanced Operations
■ Listening Mode*7
` You can select the listening modes that are grouped in
the following categories: “MOVIE/TV”, “MUSIC”,
“GAME”, and “THX”.
Use q/w to select the category and e/r to select the
listening mode. Press Enter to switch to the selected
listening mode.
Note
*1
*2
*3
*4
*5
*6
*7
• The video preview is not displayed when:
– HDMI IN 5/6/7/8 is the current HDMI input source, or
– No signal is present on the current input source, or
– The “Zone 2 HDMI” setting is set to “Use” (➔ page 59).
• The video of the currently-selected input is displayed on the
main screen, not on a preview thumbnail.
“Dolby Volume”, “Dynamic EQ” and “Dynamic Volume”
cannot be selected when any of the THX listening modes is
selected, with “Loudness Plus” set to “On” or “Preserve
THX Settings” set to “Yes” (➔ page 66).
When “Dynamic EQ” is set to “On” or “Dynamic Volume”
is set to anything else than “Off”, “Dolby Volume” will be
switched to “Off” (➔ page 69).
• When the “Monitor Out” setting is set to “Sub”, “Video”
cannot be selected (➔ page 59).
• This setting cannot be used with the NET input selector.
Only when you have selected “Custom” in the “Picture
Mode” (➔ page 74), pressing Enter allows you to adjust the
following items via the Quick Setup: “Brightness”,
“Contrast”, “Hue” and “Saturation”. Press Return to return
to the “Picture Mode” setting.
Depending on the input source and listening mode, not all
channels shown here output the sound.
• This setting is not available in either of the following cases:
– The “Audio TV Out” setting is set to “On” (➔ page 81).
– “HDMI Control(RIHD)” is set to “On” (➔ page 80) and
you’re listening through your TV speakers.
Using the Audio Settings of Quick
Setup
You can change various audio settings from the Quick
Setup (➔ page 53).
Note
• These settings are not available in either of the following cases:
– The “Audio TV Out” setting is set to “On” (➔ page 81).
– “HDMI Control(RIHD)” is set to “On” (➔ page 80) and
you’re listening through your TV speakers.
Sound Program
■ Sound Program
` Stereo Source 1, Stereo Source 2, Stereo Source 3,
Multich Source 1, Multich Source 2, Multich
Source 3
` Off
With this setting, you can select the combination of
settings that you registered in “Sound Program Edit”
(➔ page 71).
Note
• If the input selector is changed, the “Sound Program” setting is
switched back to “Off”.
En-54
Tone Control
■ Bass
`–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds output.
■ Treble
`–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output.
You can adjust the bass for the front, front wide, front high,
center, surround, surround back and subwoofer speakers
and treble for the front, front wide, front high, center,
surround and surround back speakers, except when the
Direct or THX listening mode is selected.
Operating on the AV receiver
1
Press Tone repeatedly to select either “Bass” or
“Treble” for each speaker or subwoofer.
2
Use – and + to adjust.
Note
• Speakers that are set to “No” or “None” in “Speaker
Configuration” (➔ page 64) cannot be adjusted.
• When “Sound Program” is enabled, “Subwoofer 1” and
“Subwoofer 2” cannot be used if the “Subwoofer” setting is set
to “No” in “Sound Program Edit” (➔ page 71).
Advanced Operations
Speaker Levels
Dolby Volume
Late Night
■ Subwoofer 1
` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■ Dolby Volume
See “Dolby Volume” of “Audio Adjust” (➔ page 69).
■ Late Night
For Dolby Digital and Dolby Digital Plus sources, the
options are:
`Off
`Low:
Small reduction in dynamic range.
`High:
Large reduction in dynamic range.
■ Subwoofer 2*1
` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■ Center
` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Calibration” (➔ page 65) before
setting the AV receiver to standby.
Note
• You cannot use these function while the AV receiver is muted.
• These settings cannot be used while a pair of headphones is
connected.
• Speakers that are set to “No” or “None” in “Speaker
Configuration” (➔ page 64) cannot be adjusted.
• When “Sound Program” is enabled, “Subwoofer 1” and
“Subwoofer 2” cannot be used if the “Subwoofer” setting is set
to “No” in “Sound Program Edit” (➔ page 71).
*1 If the “Subwoofer” setting is set to “1ch”, this setting cannot
be selected (➔ page 64).
Note
• This setting cannot be used in either of the following cases:
– The Direct listening mode is selected.
– Any of the THX listening modes is selected, with “Loudness
Plus” set to “On” or “Preserve THX Settings” set to “Yes”
(➔ page 66).
• When “Dolby Volume” is set to “On”, the “Dynamic EQ” and
“Dynamic Volume” settings of all input selectors are switched to
“Off”.
• When “Sound Program” is enabled, the setting must be made
with “Sound Program Edit” (➔ page 71).
Audyssey®
■ Audyssey
See “Audyssey” in “Source Setup” (➔ page 72).
■ Dynamic EQ
See “Dynamic EQ” in “Source Setup” (➔ page 72).
■ Dynamic Volume
See “Dynamic Volume” in “Source Setup” (➔ page 72).
Note
• These technologies can be used when all the following conditions
are met:
– Room Correction and Speaker Setup is completed. Note that
“Audyssey” requires the “Audyssey MultEQ XT32 Full
Calibration” method.
– Any listening mode other than Direct is selected.
– A pair of headphones is not connected.
• The setting is stored individually for each input selector.
• “Dynamic EQ” and “Dynamic Volume” cannot be selected
when any of the THX listening modes is selected, with
“Loudness Plus” set to “On” or “Preserve THX Settings” set to
“Yes” (➔ page 66).
• When “Sound Program” is enabled, the setting must be made
with “Sound Program Edit” (➔ page 71).
En-55
For Dolby TrueHD sources, the options are:
`Auto:
The Late Night function is set to “On” or “Off”
automatically.
`Off
`On
Turn this setting on to reduce the dynamic range of Dolby
Digital material so that you can still hear quiet parts even
when listening at low volume levels—ideal for watching
movies late at night when you don’t want to disturb
anyone.
Note
• The effect of the Late Night function depends on the material that
you are playing and the intention of the original sound designer,
and with some material there will be little or no effect when you
select the different options.
• The Late Night function can be used only when the input source
is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.
• The Late Night function is set to “Off” when the AV receiver is
set to standby. For Dolby TrueHD sources, it will be set to
“Auto”.
• With Dolby TrueHD sources, the Late Night function cannot be
used when “TrueHD Loudness Management” is set to “Off”
(➔ page 69).
• The Late Night function cannot be used when “Dolby Volume”
is set to “On”.
Advanced Operations
Music Optimizer
Re-EQ
Screen Centered Dialog
■ Music Optimizer
` Off
` On
The Music Optimizer function enhances the sound quality
of compressed music files. When set to “On”, the M.Opt
indicator lights on the AV receiver’s display.
With the Re-EQ function, you can compensate a
soundtrack whose high-frequency content is too harsh,
making it more suitable for home theater viewing.
By using the front high speaker, this function moves the
center image of dialogs etc. upwards, so that the image of
dialogs is fixed to the display height.
■ Re-EQ
` Off
` On
This function can be used with the following listening
modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD,
Multichannel, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio, DTS Express, DSD, Dolby EX,
Dolby Pro Logic IIz Height, Dolby PLIIx Movie, DTS
Neo:X Cinema.
■ Screen Centered Dialog
As the value increases, the center image moves upwards.
`0
`1 to 5:
Screen Centered Dialog on.
Note
• The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and analog
audio input signals.
• The Music Optimizer is disabled when the Direct listening mode
is selected.
• The setting is stored individually for each input selector.
• When “Sound Program” is enabled, the setting must be made
with “Sound Program Edit” (➔ page 71).
■ Re-EQ(THX)
` Off
` On
This function can be used with the following listening
modes: THX Cinema, THX Surround EX, and
THX Ultra2 Cinema.
Note
• These settings are stored individually for each input selector. In
THX listening mode however, the setting will return to “On”
when the AV receiver is turned off.
• These settings cannot be used while a pair of headphones is
connected.
En-56
Note
• The “Screen Centered Dialog” can be used when a compatible
listening mode is selected.
• This setting cannot be used while a pair of headphones is
connected.
Advanced Operations
Using the Setup Menu (Home)
■ Screen Saver
If there is no video signal on the current input source and
no operation for a specific time (three minutes by
default), a screen saver automatically comes on.
Explanatory Notes
a
Main Menu
Speaker Setup
b
Speaker Configuration
c
d
■ Subwoofer
` 1ch:
The audio signal is outputted from
SW/SUBWOOFER 1 jack only.
` 2ch:
The audio signal is outputted from
SW/SUBWOOFER 1 and 2 jacks.
Tip
Receiver
Enter
q/w/e/r
• The time until the screen saver activates itself can be changed
in the “Screen Saver” setting (➔ page 79).
• The screen will return to its previous state if the AV receiver is
operated.
Return
a Main Menu
b Sub Menu
c Setting target
d Setting options (default setting underlined)
Home
1
2
3
Press Receiver followed by Home.
Use e/r to select “Setup”, and then press Enter.
Use q/w to select a main menu item, and then press
Enter.
4
Use q/w to select a sub menu item, and then press
Enter.
5
Use q/w to select a setting target, and use e/r to
change the setting.
Press Home to close the menu.
Press Return to return to the previous menu.
Sub Menu
Main Menu
Note
• This procedure can also be performed on the AV receiver by
using Setup, the cursor and enter (middle) buttons.
• During Audyssey MultEQ® XT32 Room Correction and Speaker
Setup, messages, etc., that are displayed on the TV screen will
appear on the AV receiver’s display.
En-57
Advanced Operations
About the Hybrid Standby Indicator
By way of optimized circuitry, this function reduces power
consumption when the AV receiver is in standby mode.
The Hybrid Standby indicator will light in either of the
following conditions:
– “HDMI Through” is enabled (the HDMI indicator is
off).
– “Network Standby” is enabled (the NET indicator is
off).
Setup Menu Items
Main menu item
Sub menu item
Listening Mode Preset
BD/DVD
(➔ page 77)
CBL/SAT
Main menu item
Sub menu item
Input/Output Assign
(➔ page 59)
Monitor Out
STB/DVR
HDMI Input
GAME1
Component Video Input
GAME2
Composite Video Input
PC
Digital Audio Input
AUX
Speaker Setup
Speaker Settings
TUNER
(➔ page 62)
Speaker Configuration
TV/CD
Speaker Distance
PHONO
Level Calibration
NET
Hybrid Standby
USB
Equalizer Settings
THX Audio Setup
Digital Processing Crossover
Network
Audio Adjust
Multiplex/Mono
(➔ page 68)
Dolby
Miscellaneous
Volume Setup
(➔ page 78)
OSD Setup
12V Trigger A Setup
12V Trigger B Setup
12V Trigger C Setup
DTS
Hardware Setup
Multi Zone
Audyssey DSX
(➔ page 79)
Tuner
Theater-Dimensional
HDMI
LFE Level
Auto Standby
Direct
Network
Sound Program Edit
Note
• If Zones are turned on or, if a mobile device connected to the
Front Input (MHL) is charging, the Hybrid Standby indicator
won’t light.
Initial Setup
Source Setup
Audyssey
(➔ page 72)
IntelliVolume
Remote Controller
Setup
A/V Sync
(➔ page 83)
Name Edit
Lock Setup
Picture Adjust
Audio Selector
En-58
(➔ page 83)
Remote ID
Remote Mode Setup
Setup
Advanced Operations
Input/Output Assign
1
2
3
Main Menu
4
Note
“Setup”
5
Input/Output Assign
Monitor Out
On the “Monitor Out” settings, you can select whether or
not to have the video sources’ images output through the
HDMI output.
If you connect your TV to the HDMI output, the “Monitor
Out” setting is automatically set and composite video and
component video sources are upconverted* and output.
Composite video,
component video
HDMI
IN
HDMI
If you connect your TV to the COMPONENT VIDEO
MONITOR OUT (not the HDMI output), “Monitor Out”
setting is automatically set and composite video source is
upconverted* and output.
Composite video
■ Monitor Out
` Analog:
Select this if your TV is connected to the
COMPONENT VIDEO MONITOR OUT or
MONITOR OUT V.
` Main:
Select this if your TV is connected to HDMI OUT
MAIN.
` Sub:
Select this if your TV is connected to HDMI OUT
SUB.
` Both:
Select this if your TVs are connected to HDMI OUT
MAIN and HDMI OUT SUB. Video signals are
output from both HDMI outputs at the resolution
supported by both TVs.
Note
OUT
Composite video,
component video
• See “Video Connection Formats” (➔ page 108) for charts
showing how the “Monitor Out” and “Resolution” settings
affect the video signal flow through the AV receiver.
• The “HDMI Through” setting is only available for the HDMI
OUT MAIN jack (➔ page 80).
Changing the “Monitor Out” setting manually
1
Press Monitor Out on the front panel.
The current setting is displayed.
2
Press Monitor Out on the AV receiver repeatedly
to select:
` Analog, HDMI Main, HDMI Sub or Both.
Component video
IN
OUT
Composite video
Component video
■ Zone 2 HDMI
`Not Use
`Use
When this setting is enabled, the TV connected to HDMI
OUT ZONE 2 can be used as the TV of Zone 2.
Tip
• On the connected component, select the mode in which the delay
between the video and audio does not occur much if the video
signal delay occurs during the playback on the video component
connected to the AV receiver.
Note
• This setting cannot be selected if the “Monitor Out” setting is set
to “Sub” or “Both”.
• When this setting is set to “Use”, the “11ch Playback” setting is
fixed to “No” (➔ page 63).
■ Resolution
`Through*1:
Select this to pass video through the AV receiver at
the same resolution and with no conversion.
`Auto*2:
Select this to have the AV receiver automatically
convert video at resolutions supported by your TV.
`480p (480p/576p), 720p, 1080i:
Select the desired output resolution.
`1080p*2:
Select this for 1080p output and video conversion as
necessary.
`1080p/24*2:
Select this for 1080p output at 24 frames per second.
`4K Upscaling*2:
Select this for an output resolution four times that of
1080p. Depending on the resolution supported by
your TV, it will result in either 3840 × 2160 or 4096
× 2160 pixels.
`Source:
Select this for an output following the resolution level
set in “Picture Adjust” (➔ page 74).
To be continued
En-59
Advanced Operations
You can specify the output resolution for HDMI OUT
MAIN and COMPONENT VIDEO MONITOR OUT so
that the AV receiver upconverts the picture resolution as
necessary to match the resolution supported by your TV.
Tip
• You can see the picture by pressing Enter to check the
“Resolution” setting for HDMI OUT MAIN (excluding NET
input source).
Note
• Depending on the incoming video signal, the video playback may
not be smooth or the vertical resolution may be lowered. In this
case select anything other than “1080p/24”.
• With some TVs, there may be no picture when this setting is set
to “4K Upscaling”.
• If the “Monitor Out” setting is set to “Sub”, this setting is fixed
to “Through”.
• If the “Monitor Out” setting is set to “Both”, this setting is fixed
to “Auto”.
*1 PC IN (Analog RGB input) signal is output at 480p
(480p/576p), 720p, 1080i resolution when the “Monitor Out”
setting is set to “Analog” (➔ page 59) and the “Resolution”
setting is set to “Through”.
*2 These settings are not available when the “Monitor Out”
setting is set to “Analog” (➔ page 59).
HDMI Input
*2
If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to HDMI IN 2,
you must assign “HDMI2” to the “BD/DVD” input
selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, composite video and component video
sources can be upconverted* and output by the HDMI
output*1. You can set this for each input selector by
selecting the “- - - - -” option, but the video signal coming
from the HDMI output depends on the assignments of
“Component Video Input” and “Composite Video
Input”. See “Video Connection Formats” for more
information on video signal flow and upconversion
(➔ page 108).
Composite video,
component video
HDMI
IN
*1
HDMI
This applies only when “Monitor Out” setting is set to other
than “Analog” (➔ page 59).
Here are the default assignments.
Input selector
Default assignment
BD/DVD
HDMI1
CBL/SAT
HDMI2
STB/DVR
HDMI3
GAME1
HDMI4
GAME2
HDMI5
PC
HDMI6*2
AUX
FRONT (Fixed)
TV/CD
-----
PHONO
-----
En-60
■ BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, TV/CD, PHONO
`HDMI1, HDMI2, HDMI3, HDMI4, HDMI5,
HDMI6, HDMI7, HDMI8:
Select the input to which the component has been
connected.
`- - - - -:
Output composite video and component video
sources from the HDMI output. The video signal
coming from the HDMI output depends on the
assignments of “Component Video Input” and
“Composite Video Input”.
Each HDMI input cannot be assigned to two input selectors
or more. When HDMI1 - HDMI8 have already been
assigned, you must first set any unused input selectors to
“- - - - -” or you will be unable to assign HDMI1 - HDMI8
to other input selectors.
Note
OUT
Composite video,
component video
If you connect your personal computer to PC IN (Analog
RGB), you must assign “- - - - -” to the “PC” input selector.
• For composite video and component video upconversion for the
HDMI output, the “Monitor Out” setting must be set to other
than “Analog” (➔ page 59), and the “HDMI Input” setting
must be set to “- - - - -”. See “Connection Tips and Video Signal
Path” for more information on video signal flow and
upconversion (➔ page 108).
• The assignment of input selector selected for Zone 2 cannot be
changed when the “Zone 2 HDMI” is set to “Use” (➔ page 59).
• If no video component is connected to the HDMI input (even if
the HDMI input is assigned), the AV receiver selects the video
source based on the setting of “Component Video Input” and
“Composite Video Input”.
• When an HDMI IN is assigned to an input selector as explained
here, the same HDMI IN will be set as a priority in the “Digital
Audio Input” (➔ page 62). In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the “Audio Selector” setting (➔ page 76).
To be continued
Advanced Operations
• Do not assign an HDMI IN to the TV/CD selector while “HDMI
Control(RIHD)” is set to “On” (➔ page 80), otherwise
appropriate CEC (Consumer Electronics Control) operation will
not be guaranteed.
• If you assign “- - - - -” to an input selector that is currently
selected in “HDMI Through” (➔ page 80), the “HDMI
Through” setting will be automatically switched to “Off”.
• “AUX” is used only for input from the front panel.
Component Video Input
If you connect a video component to a component video
input, you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player to
COMPONENT VIDEO IN 2, you must assign “IN2” to
the “BD/DVD” input selector.
If you’ve connected your TV to the AV receiver with a
component video cable, you can set the AV receiver so that
composite video source is upconverted* and output by the
COMPONENT VIDEO MONITOR OUT*1. You can set
this for each input selector by selecting the “- - - - -”
option.
Composite video
Component video
IN
OUT
Composite video
*1
Component video
This applies only when “Monitor Out” setting is set to
“Analog” (➔ page 59).
Here are the default assignments.
Input selector
Default assignment
BD/DVD
IN1
CBL/SAT
IN2
STB/DVR
-----
GAME1
-----
GAME2
-----
PC
-----
AUX
-----
TV/CD
-----
PHONO
-----
En-61
■ BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, AUX, TV/CD, PHONO
`IN1, IN2:
Select the input to which the component has been
connected.
`- - - - -:
Output composite video sources from the HDMI
output. The upconverted output from HDMI depends
on the assignment of “Composite Video Input”.
Note
• For composite video upconversion for the COMPONENT
VIDEO MONITOR OUT, the “Monitor Out” setting must be
set to “Analog” (➔ page 59), and the “Component Video
Input” setting must be set to “- - - - -”. See “Connection Tips and
Video Signal Path” for more information on video signal flow
and upconversion (➔ page 108).
Advanced Operations
Composite Video Input
Digital Audio Input
If you connect a component to a composite video input,
you must assign that input to an input selector.
If you switch the input to “TV/CD” with its default
assignment, the audio of “TV/CD” is output while the
video of the previously-selected source is displayed.
Here are the default assignments.
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPTICAL1” to the “TV/CD” input selector.
Here are the default assignments.
Input selector
Default assignment
Input selector
Default assignment
BD/DVD
COAXIAL1
BD/DVD
IN1
CBL/SAT
COAXIAL2
CBL/SAT
IN2
STB/DVR
COAXIAL3
STB/DVR
IN3
GAME1
OPTICAL1
GAME1
IN4
GAME2
-----
GAME2
-----
PC
-----
PC
PC IN (Fixed)
AUX
FRONT (Fixed)
AUX
FRONT (Fixed)
TV/CD
OPTICAL2
TV/CD
-----
PHONO
-----
PHONO
-----
■ BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
TV/CD, PHONO
` IN1, IN2, IN3, IN4:
Select the input to which the component has been
connected.
` - - - - -:
The composite video is not input.
Note
• “AUX” is used only for input from the front panel.
• “PC” is used only for input from PC IN.
• Using these inputs as audio-exclusive allows you to enjoy audio
and video from separate inputs. Refer to “Playing Audio and
Video from Separate Sources” for details (➔ page 37).
Speaker Setup
1
2
Main Menu
3
4
“Setup”
5
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ® XT32 Room Correction and
Speaker Setup function (➔ page 38).
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function, or set them manually, which is useful if
you change one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function.
Note
■ BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, TV/CD, PHONO
` COAXIAL1, COAXIAL2, COAXIAL3,
OPTICAL1, OPTICAL2:
Select the input to which the component has been
connected.
` - - - - -:
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in
“HDMI Input” (➔ page 60), the same HDMI IN will be set as
a priority in this assignment. In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the “Audio Selector” (➔ page 76).
• Supported sampling rates for PCM signals (stereo/mono) from a
digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,
20, 24 bit.
• “AUX” is used only for input from the front panel.
En-62
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the “Audio TV Out” setting is set to “On” (➔ page 81).
– “HDMI Control(RIHD)” is set to “On” (➔ page 80) and
you’re listening through your TV speakers.
Advanced Operations
Speaker Settings
If you change these settings, you must run
Audyssey MultEQ® XT32 Room Correction and
Speaker Setup again (➔ page 38).
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“Speakers Type(Front)” setting. For details on speaker
wire connection, see “Bi-amping the Front Speakers”
(➔ page 14). When connecting speakers without
crossover network, you need to change the “Speakers
Type(Front)” setting beforehand. For details on
connection, refer to “Using Speakers Without Crossover
Network” (➔ page 14).
Note
• When bi-amping is used, the AV receiver is able to drive up to 7.2
speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms:
Select if the impedances of all speakers are between 6
and 16 ohms.
■ Speakers Type(Front)
` Normal:
Select this if you’ve connected your front speakers
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers.
` Digital Crossover:
Select this if you’re using speakers without crossover
network.
Tip
• If “Speakers Type(Front)” is set to “Digital Crossover”, a
confirmation screen appears. Select “Next (2-7. Digital
Processing Crossover Network)” to display the screen for
Digital Processing Crossover Network (➔ page 67). Continue
with the settings.
■ Passive Subwoofer
` Yes:
Select this if you’ve connected passive subwoofers.
` No
■ Powered Zone 2, Powered Zone 3, Powered
Zone 4
` No
` Yes:
Zone 2/3/4 speakers can be used. (Powered
Zone 2/3/4 enabled).
■ 11ch Playback
` No
` Yes
For 11.2-channel playback, set this setting to “Yes”. If you
select front wide speakers setting in Speaker Configuration
is set to “None”, it will be automatically switched to
“80Hz (THX)”.
Note
• If the “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”, passive subwoofer cannot be used.
• Powered Zone 3 is not available in the following cases:
– The “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”.
– The “Passive Subwoofer” setting is set to “Yes”.
– The “Powered Zone 2” setting is set to “No”.
• Powered Zone 4 is not available in the following cases:
– The “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”.
– The “Passive Subwoofer” setting is set to “Yes”.
– The “Powered Zone 3” setting is set to “No”.
• When the “Powered Zone 3” setting is set to “Yes”
(➔ page 63) while Powered Zone 2 is enabled (➔ page 86),
the surround back speakers cannot be used.
En-63
• When the “Powered Zone 2” setting is set to “Yes”, the front
wide speakers cannot be used.
• When the “Powered Zone 3” setting is set to “Yes”, the front
high speakers cannot be used.
• When the “Powered Zone 4” setting is set to “Yes”, the surround
back speakers cannot be used.
• “11ch Playback” is not available in the following cases:
– The “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”.
– The “Passive Subwoofer” setting is set to “Yes”.
– The “Powered Zone 2” setting is set to “Yes”.
– The “Zone 2 HDMI” setting is set to “Use”.
• If the “11ch Playback” setting is set to “Yes”, the audio of front
wide channel is output from FRONT WIDE PRE OUT only.
Advanced Operations
Speaker Configuration
This setting is set automatically by
Audyssey MultEQ® XT32 Room Correction and
Speaker Setup function (➔ page 38).
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
` 1ch:
The audio signal is outputted from
SW/SUBWOOFER 1 jack only.
` 2ch:
The audio signal is outputted from
SW/SUBWOOFER 1 and 2 jacks.
` No
Note
• If the “Passive Subwoofer” setting is set to “Yes”, “No” cannot
be selected here.
■ Front
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center*1, Surround*1*9
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Front Wide*1*3*4*6*7*10, Front High*1*2*3*6*10
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Surround Back*1*5*6*8*11*12
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2 When the “Powered Zone 3” setting is set to “Yes”, this
setting cannot be selected.
*3 This setting cannot be selected if the “Speakers Type(Front)”
setting is set to “Bi-Amp” or “Digital Crossover”.
*4 When the “Powered Zone 2” setting is set to “Yes”, this
setting cannot be selected.
*5 When the “Powered Zone 3” setting is set to “Yes”
(➔ page 63) while Powered Zone 2 is enabled (➔ page 86),
this setting cannot be selected.
*6 If the “Surround” setting is set to “None”, this setting cannot
be selected.
*7 If the “11ch Playback” setting is enabled, “None” cannot be
selected.
*8 When the “Speakers Type(Front)” setting is set to “Bi-Amp”
or “Digital Crossover” while Powered Zone 2 is enabled
(➔ page 86), this setting cannot be selected.
*9 When the “Powered Zone 4” setting is set to “Yes” and
Zone 4 is turned on, this setting cannot be selected.
*10 If the “Passive Subwoofer” setting is set to “Yes”
(➔ page 63), this setting cannot be selected.
*11 When the “Powered Zone 4” setting is set to “Yes”, this
setting cannot be selected.
En-64
*12 If
the “Passive Subwoofer” setting is set to “Yes”
(➔ page 63) while Powered Zone 2 is enabled
(➔ page 86), this setting cannot be selected.
■ Surround Back Ch
`1ch:
Select if only one surround back speaker L is
connected.
`2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the “Surround Back” setting is set to “None”, this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
`80Hz, 90Hz, 100Hz, 110Hz, 120Hz
`Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency of
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
Note
• If you’re using THX-certified speakers, select “80Hz”.
■ Subwoofer Phase
`0º
`180º:
Moves the subwoofer phase.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot be
selected.
Advanced Operations
■ Double Bass
This setting is NOT set automatically by
Audyssey MultEQ® XT32 Room Correction and
Speaker Setup function (➔ page 38).
` On
` Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to
the subwoofer.
Note
• When the “Subwoofer” setting is set to “No” or the “Front”
setting to anything other than “Full Band”, this setting is fixed to
“- - - - -”.
• This setting is set to “On” automatically when the “Subwoofer”
setting is set to “1ch” or “2ch” and the “Front” setting is set to
“Full Band” for the first time.
• If you’re using THX-certified speakers, select “Off(THX)”.
Speaker Distance
Level Calibration
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (➔ page 38).
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (➔ page 38).
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer intended.
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■ Unit
` feet:
Distances can be set in feet. Range: 0.2ft to 60.0ft in
0.2 foot steps.
` meters:
Distances can be set in meters. Range: 0.06m to
18.00m in 0.06 meter steps.
(The default setting varies from country to country.)
■ Left, Front Wide Left, Front High Left, Center*1,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right, Surround
Back Left, Surround Left
`–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■ Left, Front Wide Left, Front High Left, Center,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right, Surround
Back Left, Surround Left, Subwoofer 1,
Subwoofer 2*1
` Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “No” or “None” in “Speaker
Configuration” cannot be selected (➔ page 64).
• When the “Powered Zone 4” setting is set to “Yes” and Zone 4
is turned on, the surround speakers cannot be used.
• When the “Powered Zone 3” setting is set to “Yes”
(➔ page 63) while Powered Zone 2 is enabled (➔ page 86),
the surround back speakers cannot be used.
*1 If the “Subwoofer” setting is set to “1ch”, this setting cannot
be selected (➔ page 64).
■ Subwoofer 1*1, Subwoofer 2*1*2
`–15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
Note
• These settings cannot be calibrated when the AV receiver is
muted.
• Speakers that you set to “No” or “None” in “Speaker
Configuration” cannot be selected (➔ page 64).
• When the “Powered Zone 3” setting is set to “Yes”
(➔ page 63) while Powered Zone 2 is enabled (➔ page 86),
the surround back speakers cannot be used.
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at
volume settings below this, be careful because the test tone will
be much louder.
• When the “Powered Zone 4” setting is set to “Yes” and Zone 4
is turned on, the surround speakers cannot be used.
*1 For the center speaker and subwoofer, the level settings made
by using the Quick Setup are saved in this menu (➔ page 55).
*2 If the “Subwoofer” setting is set to “1ch”, this setting cannot
be selected (➔ page 64).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
En-65
Advanced Operations
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 15-band equalizer. The
volume of each speaker can be set (➔ page 65).
■ Manual Equalizer
` On:
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
1
Press w to select “Channel”, and then use e/r to
select a speaker.
2
Use q/w to select a frequency, and then use the e/r
to adjust the level at that frequency.
The volume at each frequency can be adjusted from
–6dB to 0dB to +6dB in 1 dB steps.
Tip
• You can select: “25Hz”, “40Hz”, “63Hz”, “100Hz”,
“160Hz”, “250Hz”, “400Hz”, “630Hz”, “1000Hz”,
“1600Hz”, “2500Hz”, “4000Hz”, “6300Hz”, “10000Hz”,
or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”,
“63Hz”, “100Hz”, or “160Hz”.
• Low frequencies (e.g., 25 Hz) affect bass sounds; high
frequencies (e.g., 16000 Hz) affect treble sounds.
3
Use q to select “Channel”, and then use e/r to
select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “No” or
“None” in the “Speaker Configuration”
(➔ page 64).
` Off:
Tone off, response flat.
Note
Note
• When the Direct listening mode is selected, the equalizer settings
have no effect.
• If “Audyssey” is enabled, it prevails over this setting
(➔ page 72).
THX Audio Setup
■ Surr Back Speaker Spacing
` <1ft (<0.3m)
` 1ft-4ft (0.3m-1.2m)
` >4ft (>1.2m)
You can specify the distance between your surround back
speakers.
Note
• This setting is not available in any of the following cases:
– “Surround Back” is set to “None” (➔ page 64).
– “Surround Back Ch” is set to “1ch” (➔ page 64).
– The “Powered Zone 3” setting is set to “Yes” (➔ page 63)
while Powered Zone 2 is enabled (➔ page 86).
■ THX Ultra2/Select2 Subwoofer
` No
` Yes
If you’re using a THX-certified subwoofer, set this setting
to “Yes”.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot be
selected (➔ page 64).
■ BGC
` Off
` On
You can apply THX’s Boundary Gain Compensation
(BGC) to compensate the perceived exaggeration of low
frequencies for listeners sitting very close to a room
boundary (i.e., wall).
En-66
• This setting is only available if “THX Ultra2/Select2
Subwoofer” is set to “Yes”.
• If the “Subwoofer” setting is set to “No”, this setting cannot be
selected (➔ page 64).
■ Loudness Plus
`Off
`On
When the “Loudness Plus” setting is set to “On”, it is
possible to enjoy even subtle nuances of audio expression
at low volume. This is only available when the THX
listening mode is selected.
■ Preserve THX Settings
`Yes
`No
If this setting is set to “Yes”, Dynamic EQ,
Dynamic Volume and Dolby Volume have no effect in
THX listening mode.
Note
• This setting is fixed at “Yes” if “Loudness Plus” is set to “On”.
■ Metadata Compatible
`On:
When Metadata Compatible is set to “On”, valid
metadata is transmitted via the HDMI connections,
and can be used by other devices in the system.
`Off:
When Metadata Compatible is set to “Off”, metadata
is not transmitted via the HDMI connections.
To be continued
Advanced Operations
The HDMI connection in your system is used to deliver
uncompressed digital audio and video information from
one device to the next. There is also additional information
about this digital content that can be delivered. Such
additional information is referred to as “metadata”.
Metadata Compatible mode should be used when there are
home theater components in your system, such as Blu-ray
disc players, set top boxes and displays that use this
additional metadata. For example, Metadata Compatible
mode should be set to ON when there are THX Media
Director™ Enabled devices in the system. This ensures
that this additional information can be received by your
Integra AVR and can be sent to other devices that are
connected in your home theater system, with no
interruption.
THX Loudness Plus
THX Loudness Plus is a new volume control technology
featured in THX Ultra2 Plus™ and THX Select2 Plus™
Certified receivers. With THX Loudness Plus, home
theater audiences can now experience the rich details in a
surround mix at any volume level. A consequence of
turning the volume below Reference Level is that certain
sound elements can be lost or perceived differently by
the listener. THX Loudness Plus compensates for the
tonal and spatial shifts that occur when the volume is
reduced by intelligently adjusting ambient surround
channel levels and frequency response. This enables
users experience the true impact of soundtracks
regardless of the volume setting. THX Loudness Plus is
automatically applied when listening in any THX
listening mode. The new THX Cinema, THX Music, and
THX Games modes are tailored to apply the proper THX
Loudness Plus settings for each type of content.
Digital Processing Crossover Network
Digital Crossover provides a separate routing system by
splitting the audio signal into separate frequency bands
optimized for each speaker driver. It provides a fine, threedimensional sound field that extend each driver’s
performance to the uppermost. With its built-in time
alignment function, this system also adjusts the sound
shifting that occurs when there is a physical offset between
sound drivers. At a digital processing level, it corrects this
offset by delaying the related audio signal.
Although this function is meant for speakers without
crossover network, it can also be used with bi-amped
speakers.
Tip
• This setting can be done while listening to an audio source.
• Press Mode/D (Blue) to switch from the current audio source to
test noises. Pressing Mode/D (Blue) again or the cursor buttons
will stop the test noises and switch back to the original audio
source.
Note
• Refer to your speaker manual when setting without the use of test
noises.
Cutoff frequencies of the woofers’ low-pass filter (LPF)
and the tweeters’ high-pass filter (HPF) are set according
to the frequency specified for “Crossover”.
■ Overlap
`No
`Yes
With this setting, a frequency band near the specified
crossover frequency is output by both tweeters and
woofers. Based on the frequency selected for “Crossover”,
the cutoff frequency of the low-pass filter (LPF) will be set
to 1/3 octave up and that of the high-pass filter (HPF) to
1/3 octave down. Example: With a “Crossover” of
“3200Hz”, the cutoff frequency of the woofers’ LPF will
be “4000Hz”, and the tweeters’ HPF will be “2500Hz”.
Tip
Note
• This setting can only be made when “Speakers Type(Front)” is
set to “Digital Crossover” (➔ page 63).
■ Crossover
` “250Hz”, “320Hz”, “400Hz”, “500Hz, “630Hz”,
“800Hz”, “1000Hz”, “1250Hz”, “1600Hz”,
“2000Hz”, “2500Hz”, “3200Hz”, “4000Hz”,
“5000Hz”
Output Band for Test
` High + Low, High, Low:
Select the output for the audio signal.
Tip
• Pressing Mode/D (Blue) button plays band-limited test noises
which center on the specified frequency.
• We recommend choosing a crossover value that creates no
volume difference between “High” and “Low”.
En-67
• Sounds processed by Digital Processing Crossover Network are
played.
• You can switch from the current audio source to test noises by
pressing Mode/D (Blue).
• In the case of usage of the bi-amped speakers, if there is a
difference between the crossover frequency in the speakers’ builtin network and the crossover frequency to be set on the AV
receiver, the frequency dip may be caused. Therefore, it is
recommended that this function should be set to “Yes”.
■ High Level, Low Level
`–6.0dB to 0.0dB to +6.0dB in 0.5 dB steps.
With this setting, you can set the volume of tweeters and
woofers.
Tip
• Sounds processed by Digital Processing Crossover Network are
played.
• You can switch from the current audio source to test noises by
pressing Mode/D (Blue).
Advanced Operations
■ High Phase, Low Phase
` 0º
` 180º:
With this setting, you can adjust the phase of tweeters and
woofers.
Audio Adjust
1
2
3
Main Menu
Tip
• Sounds processed by Digital Processing Crossover Network are
played.
• You can switch from the current audio source to test noises by
pressing Mode/D (Blue).
■ High Distance, Low Distance
` 0inch(0.0cm) to 12inch(30.0cm) in 1 inch (2.5 cm)
steps.
With this setting, you can adjust the virtual position of
tweeter and woofer units. Adjusting “High Distance”
virtually shifts woofers behind tweeters. Adjusting “Low
Distance” virtually shifts tweeters behind woofers.
Tweeter
Distance
Distance
Woofer
(Low Distance)
(High Distance)
4
“Setup”
5
Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Output Speaker
`Center:
Mono audio is output by the center speaker.
`Left / Right:
Mono audio is output by the front left and right
speakers.
This setting determines which speakers output mono audio
when the Mono listening mode is selected.
Note
• If the “Center” setting is set to “None” (➔ page 64), this setting
cannot be selected.
Multiplex/Mono
■ Multiplex
Input Channel
` Main
` Sub
` Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
■ Mono
Input Channel
` Left + Right
` Left
` Right
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode.
Tip
• Sounds processed by Digital Processing Crossover Network are
played.
• You can switch from the current audio source to test noises by
pressing Mode/D (Blue).
En-68
Dolby
■ PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo sources.
If you’re not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro Logic
IIx.
Panorama
`On
`Off
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
Dimension
`–3 to 0 to +3
With this setting, you can move the sound field forward or
backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it’s
in mono, or there’s not enough surround sound, move it
backward.
Advanced Operations
Center Width
` 0 to 3 to 7
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you’re using a
center speaker, the center channel sound is output from
only the center speaker. (If you’re not using a center
speaker, the center channel sound will be distributed to the
front left and right speakers to create a phantom center).
This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel
sound.
■ PL IIz Height Gain
` Low
` Mid
` High
The Height Gain Control in Dolby Pro Logic IIz enables
the listener to select how much gain is applied to the front
high speakers. There are three settings, “Low”, “Mid” and
“High”, and the front high speakers are accentuated in that
order. While “Mid” is the default listening setting, the
listener may adjust the Height Gain Control to their
personal preference.
Note
• If the “Front High” setting is set to “None” (➔ page 64), this
setting cannot be selected.
■ Dolby EX
` Auto:
If the source signal contains a Dolby EX flag, the
Dolby EX or THX Surround EX listening mode is
used.
` Manual:
You can select any available listening mode.
This setting determines how Dolby EX encoded signals are
handled. This setting is unavailable if no surround back
speakers are connected. This setting is effective with
Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.
Note
• If the “Surround Back” setting is set to “None” (➔ page 64),
this setting cannot be selected.
• If the “Powered Zone 2/3” setting is set to “Yes” and Zone 2 is
turned on, this setting cannot be selected.
• When the “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”, this setting cannot be selected if the
“Powered Zone 2” setting is set to “Yes” and Zone 2 is turned
on.
• If the “Front High” or “Front Wide” setting is enabled
(➔ page 64), this setting is fixed to “Manual”.
• If the “Passive Subwoofer” setting is set to “Yes” (➔ page 63)
while Powered Zone 2 is enabled (➔ page 86), this setting
cannot be selected.
■ TrueHD Loudness Management
` Off
` On
This setting specifies whether or not to apply the Late
Night processing on a Dolby TrueHD source.
Note
• When this setting is set to “Off”, the Late Night function for
Dolby TrueHD sources is automatically fixed to “Off”.
• When this setting is set to “Off”, the Dialogue Normalization
information is not available for Dolby TrueHD sources.
■ Dolby Volume
`Off
`On
Dolby Volume automatically adjusts the difference in
volume levels which can occur between different contents
or source components, freeing the user from having to
make volume adjustments. Also, by adjusting the
frequency balance according to the playback volume, it
recreates the original source audio. Dolby Volume
therefore provides comfortable listening, effectively
controlling the volume level difference without unnatural
changes in volume or sound quality to recreate the balance
and nuance of the source audio.
Note
• When the “Dolby Volume” setting is set to “On”,
“Dynamic EQ” and “Dynamic Volume” will be set to “Off”.
• If you would like to use Dolby Volume in THX listening modes,
set the “Loudness Plus” and “Preserve THX Settings” settings
to “Off” and “No”, respectively.
• When “Dolby Volume” is set to “On”, the Late Night function
cannot be set.
■ Volume Leveler
`Off
`Low:
Low Compression Mode activated.
`Mid:
Medium Compression Mode activated.
`High:
High Compression Mode activated. This setting
affects volume the most, causing all sounds to be of
equal loudness.
“Volume Leveler” maintains the perceived loudness of all
contents, coming from different channels or input sources.
Note
• If the “Dolby Volume” setting is set to “Off”, this setting cannot
be selected.
En-69
Advanced Operations
■ Half Mode
` Off
` On
The Half Mode parameter turns Dolby Volume Half Mode
processing on and off.
In off mode, Dolby Volume applies a bass and treble
attenuation to the audio when the system gain exceeds
reference level. This enables a more perceptually flat
listening experience as human ears are more sensitive to
bass and treble at higher levels. Some listeners however,
prefer to have more bass and treble performance at higher
gain levels.
Note
• If the “Dolby Volume” setting is set to “Off”, this setting cannot
be selected.
• During Half Mode on playback, Dolby Volume does not apply a
bass and treble attenuation when the system volume exceeds
reference level, thereby boosting perception of high and low
frequencies.
Dialogue Normalization
Dialogue Normalization (DialogNorm) is a feature of
Dolby Digital, which is used to keep the programs at the
same average listening level so the user does not have to
change the volume control between Dolby Digital,
Dolby Digital Plus and Dolby TrueHD programs. When
playing back software which has been encoded in Dolby
Digital, Dolby Digital Plus and Dolby TrueHD,
sometimes you may see a brief message in the front
panel display which will read “DialogNorm: X dB” (X
being a numeric value). The display is showing how the
program level relates with THX calibration level. If you
want to play the program at calibrated theatrical levels,
you may wish to adjust the volume. For example, if you
see the following message: “DialogNorm: + 4 dB” in
the front panel display, to keep the overall output level at
THX calibrated loudness, just turn down the volume
control by 4 dB. However, unlike a movie theater where
the playback loudness is preset, you can choose your
preferred volume setting for best enjoyment.
DTS
■ Neo:X Music
Center Image
` 0 to 2 to 5
The DTS Neo:X Music listening mode creates 11-channel
surround sound from 2-channel stereo sources. With this
setting, you can specify by how much the front left and
right channel output is attenuated in order to create the
center channel.
Changing the value from “0” to “5” will spread the sound
of the center channel to left and right (outwards).
Audyssey DSX®
■ Soundstage
`–3dB to Reference to +3dB
With this setting, you can adjust the sound stage when using
Audyssey DSX.
Note
• This listening mode can be selected only when all the following
conditions are satisfied:
– The center speaker is connected.
– Either the front high or front wide speakers are connected.
Theater-Dimensional
■ Listening Angle
`Wide:
Select if the listening angle is greater than 30 degrees.
`Narrow:
Select if the listening angle is less than 30 degrees.
With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the
front left and right speakers relative to the listening
position. Ideally, the front left and right speakers should be
equidistant from the listening position and at an angle close
to one of the two available settings.
Front left speaker
Front right speaker
Listening angle: 30°
Note
• For best results, we recommend setting “Narrow” to 20° and
“Wide” to 40°.
En-70
Advanced Operations
LFE Level
■ Dolby Digital*1, DTS*2, Multich PCM, Dolby
TrueHD, DTS-HD Master Audio, DSD*3
` –QdB, –20dB, –10dB, or 0dB
With these settings, you can set the level of the LFE (Low
Frequency Effects) channel individually for each input
sources.
If you find that low-frequency effects are too loud when
using one of these sources, change the setting to –20 dB or
–Q dB.
*1
*2
*3
Dolby Digital and Dolby Digital Plus sources
DTS and DTS-HD High Resolution sources
DSD (Super Audio CD) sources
Direct
■ Analog
Subwoofer
` Off
` On:
Analog audio signals (bass signals) are output.
This setting determines whether or not analog audio signals
(bass signals) are output from front speakers when the
Direct listening mode is selected.
Note
• If the “Subwoofer” setting is set to “No” (➔ page 64), this
setting cannot be selected.
• When Digital Processing Crossover Network is being used, this
setting is not available.
■ DSD
DAC Direct
` Off
` On:
DSD signals are not processed by the DSP.
This setting determines whether or not DSD (Super Audio
CD) audio signals pass through the DSP for processing
such as A/V Sync or delay, when the Direct listening mode
is selected.
Note
• When Digital Processing Crossover Network is being used, this
setting is not available.
Sound Program Edit
■ Sound Program
` Stereo Source 1, Stereo Source 2, Stereo Source 3,
Multich Source 1, Multich Source 2, Multich
Source 3
When playing back different content types on the same
source, or when listening to a single content type on
different sources, you can pre-register the settings that best
suit each content in “Sound Program”. The registered
settings can then be called up and modified in one set. Use
“Sound Program Edit” to register and modify a
combination of settings.
Tip
■ Equalizer*1
`Off
`Manual:
The manual setting in “Equalizer Settings”
(➔ page 66) is applied.
■ Audyssey*1
`Off, Movie, Music
See “Audyssey” (➔ page 55).
■ Dynamic EQ*1*2
`Off, On
See “Dynamic EQ” (➔ page 55).
■ Dynamic Volume*1*2
`Off, Light, Medium, Heavy
See “Dynamic Volume” (➔ page 55).
■ Dolby Volume*1
`Off, On
See “Dolby Volume” (➔ page 55).
Note
• To select the registered settings, see “Sound Program”
(➔ page 54).
■ Listening Mode
You can assign a default listening mode that will be
selected automatically when you select the sound program.
The “Last Valid” option means that the listening mode
selected last will be used.
The “Straight Decode” option means that straight
decoding listening mode (Dolby Digital, DTS, etc.) is
selected.
■ Subwoofer
` No, Yes
You can choose whether or not to use the subwoofer with
the sound program.
■ Music Optimizer*1
` Off, On
See “Music Optimizer” (➔ page 56).
En-71
• “Listening Mode” is only available when the input signal
matches the setting of “Sound Program”.
• You cannot select the “Subwoofer” setting if you set it to “No”
in “Speaker Configuration”.
• “Music Optimizer” is only available when “Stereo Source 1”,
“Stereo Source 2” or “Stereo Source 3” is selected.
• When “Audyssey Quick Start” has been used for measurement,
the “Audyssey”setting cannot be selected.
*1 This setting cannot be used when the “Listening Mode”
setting is set to “Direct”.
*2 To enable this setting, you must first perform the Room
Correction and Speaker Setup.
Advanced Operations
Source Setup
1
2
Main Menu
3
4
“Setup”
5
Source Setup
Items can be set individually for each input selector.
Preparation
Press the input selector buttons to select an input source.
Audyssey®
The tone for each speaker is set automatically by
Audyssey MultEQ® XT32 Room Correction and
Speaker Setup. To enable the following settings, you
must first perform the Room Correction and Speaker
Setup (➔ page 38).
• These technologies cannot be used when:
– a pair of headphones is connected, or
– Direct listening mode is selected.
■ Audyssey
` Off
` Movie:
Select this setting for movie material.
The Audyssey indicator will light.
` Music:
Select this setting for music material.
The Audyssey indicator will light.
Note
• When “Audyssey Quick Start” has been used for measurement,
“Audyssey” cannot be selected.
• Audyssey equalizing does not work with DSD sources.
■ Dynamic EQ
` Off
` On:
Audyssey Dynamic EQ® becomes active.
The Dynamic EQ indicator will light.
With Audyssey Dynamic EQ, you can enjoy great sound
even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of deteriorating
sound quality as volume is decreased by taking into
account human perception and room acoustics. It does so
by selecting the correct frequency response and surround
volume levels moment-by-moment so that the content
sounds the way it was created at any volume level — not
just at reference level.
■ Reference Level
Audyssey Dynamic EQ Reference Level Offset
` 0dB:
This should be selected for movie contents.
` 5dB:
Select this setting for content that has a very wide
dynamic range, such as classical music.
` 10dB:
Select this setting for jazz or other music that has a
wider dynamic range. This setting should also be
selected for TV content as that is usually mixed at
10 dB below film reference.
` 15dB:
Select this setting for pop/rock music or other
program material that is mixed at very high listening
levels and has a compressed dynamic range.
Movies are mixed in rooms calibrated for film reference.
To achieve the same reference level in a home theater
system each speaker level must be adjusted so that
–30 dBFS band-limited (500 Hz to 2000 Hz) pink noise
produces 75 dB sound pressure level at the listening
position. A home theater system automatically calibrated
by Audyssey MultEQ XT32 will play at reference level
when the master volume control is set to the 0 dB position.
At that level you can hear the mix as the mixers heard it.
En-72
Audyssey Dynamic EQ is referenced to the standard film
mix level. It makes adjustments to maintain the reference
response and surround envelopment when the volume is
turned down from 0 dB. However, film reference level is
not always used in music or other non-film content.
Audyssey Dynamic EQ Reference Level Offset provides
three offsets from the film level reference (5 dB, 10 dB,
and 15 dB) that can be selected when the mix level of the
content is not within the standard.
Note
• If “Dynamic EQ” setting is set to “Off”, this technology cannot
be used.
■ Dynamic Volume
`Off
`Light:
Activates Light Compression Mode.
`Medium:
Activates Medium Compression Mode.
`Heavy:
Activates Heavy Compression Mode. This setting
affects volume the most. It quiets the loud parts, such
as explosions, and boosts the quiet parts so they can
be heard.
Note
• If you want to use Audyssey Dynamic EQ or
Audyssey Dynamic Volume® with THX listening modes, set the
“Loudness Plus” setting to “Off” and set “Preserve THX
Settings” to “No” (➔ page 66).
• If you make Dynamic Volume active, “Dynamic EQ” is set to
“On”. The Dynamic Vol indicator will light.
• When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is
automatically switched to “Off”.
To be continued
Advanced Operations
About Audyssey Dynamic EQ®
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room
acoustics. Dynamic EQ selects the correct frequency
response and surround levels moment-by-moment at any
user-selected volume setting. The result is bass response,
tonal balance and surround impression that remain
constant despite changes in volume. Dynamic EQ
combines information from incoming source levels with
actual output sound levels in the room, a prerequisite for
delivering a loudness correction solution.
IntelliVolume
Name Edit
■ IntelliVolume
` –12dB to 0dB to +12dB in 1 dB steps.
With IntelliVolume, you can set the input level for each
input selector individually. This is useful if one of your
source components is louder or quieter than the others.
Use e/r to set the level.
If a component is noticeably louder than the others, use e
to reduce its input level. If it’s noticeably quieter, use r to
increase its input level.
You can enter a custom name for each individual input
selector and radio preset for easy identification. When
entered, the custom name will appear on the display.
The custom name is edited using the keyboard screen.
Note
About Audyssey Dynamic Volume®
Audyssey Dynamic Volume solves the problem of large
variations in volume level between television programs,
commercials, and between the soft and loud passages of
movies. Dynamic Volume looks at the preferred volume
setting by the user and then monitors how the volume of
program material is being perceived by listeners in real
time to decide whether an adjustment is needed.
Whenever necessary, Dynamic Volume makes the
necessary rapid or gradual adjustments to maintain the
desired playback volume level while optimizing the
dynamic range. Audyssey Dynamic EQ is integrated into
Dynamic Volume so that as the playback volume is
adjusted automatically, the perceived bass response,
tonal balance, surround impression and dialog clarity
remain the same whether watching movies, flipping
between television channels or changing from stereo to
surround sound content.
• IntelliVolume does not work for Zone 2/3/4.
■ Name
1
Use q/w/e/r to select a character, and then
press Enter.
Repeat this step to enter up to 10 characters.
2
To store a name when you’re done, be sure to
select “OK” by using q/w/e/r, and then press
Enter.
A/V Sync
Name input area
■ A/V Sync
` 0msec to 800msec in 1 msec steps
When using progressive scanning on your Blu-ray
Disc/DVD player, you may find that the picture and sound
are out of sync. With this setting, you can correct this by
delaying the audio signals.
Press Enter to view the TV picture while setting the delay
when the video source is output to HDMI OUT MAIN.
To return to the previous screen, press Return.
4-4. Name Edit
En-73
b
o
1
,
2
.
c
p
d
q
e
r
f
s
g
t
h
u
i
v
j
w
k
x
3
4
/
;
Shift
5
:
6
@
7
[
8
9
0
–
^
]
Space
OK
Back Space
Shift
A
N
!
<
B
O
˝
>
Shift
l
y
CLR
C
P
#
?
Shift
+10
• A/V Sync is disabled when the Direct listening mode is used with
an analog input source.
• This setting cannot be used with the NET input selector.
• The USB input selector can be used only when iPod/iPhone is
connected and Standard Mode or Extended Mode (Video) is
selected.
a
n
+10
The range of values you can adjust will depend on whether
your TV or display supports HDMI Lip Sync and if the
“Lip Sync” setting is set to “On” or not (➔ page 81).
Note
BD/DVD
Name
D
Q
$
+
E
R
%
F
S
&
`
G
T
’
{
H
U
(
I
V
)
J
W
_
K
X
=
L
Y
˜
m
z
\
All Erase
M
Z
|
}
Space
OK
Back Space
CLR
All Erase
Advanced Operations
Space:
Enters a space character.
Shift*1:
Toggles between lower and upper case characters.
(Left)/ (Right):
Moves the cursor left or right in the Name input
area.
Back Space*2:
Moves the cursor backward and deletes one
character.
OK:
Confirms your entry.
Picture Adjust
Using Picture Adjust, you can adjust the picture quality
and reduce any noise appearing on the screen.
Press Enter to view the TV picture while setting when the
video source is output to HDMI OUT MAIN. To return to
the previous screen, press Return.
■ Wide Mode*1*2
This setting determines the aspect ratio.
` 4:3:
Tip
*1
*2
This can also be performed by using +10 on the remote
controller.
Press CLR on the remote controller to delete all the
characters you have input.
` Full:
Tip
• To name a radio preset, use Tuner to select AM or FM, and then
select the preset (➔ page 34).
• To restore a name to its default, erase all characters with CLR,
select “OK” and then press Enter.
` Zoom:
Note
• This setting cannot be used for the NET and USB input selectors.
` Wide Zoom:
` Auto:
According to the input signals and monitor output
setting, the AV receiver automatically selects the
“4:3”, “Full”, “Zoom” or “Wide Zoom” mode. See
En-74
“Monitor Out” for details on the monitor output
setting (➔ page 59).
■ Picture Mode*1*3
`Custom:
All settings can be performed manually.
`ISF Day:
Select when the room is bright.
`ISF Night:
Select when the room is dark.
`Cinema:
Select when the picture source is a movie or alike.
`Game:
Select when the video source is a game console.
`Streaming:
Attempts to reduce the mosquito noise and block
artifact effects.
`Through:
Does not adjust picture quality (changes resolution).
`Direct:
Does not adjust picture quality (does not change
resolution). The video coming from an analog input
and output by the HDMI output is processed in the
same way as “Through”.
With “Picture Mode”, you can change the following
settings to be suitable for the movie or game screen by one
operation; “Game Mode”, “Film Mode”, “Edge
Enhancement”, “Noise Reduction”, “Mosquito NR”,
“Random NR”, “Block NR”, “Resolution”,
“Brightness”, “Contrast”, “Hue”, “Saturation”, “Color
Temperature”, “Gamma”, “Red Brightness”, “Red
Contrast”, “Green Brightness”, “Green Contrast”,
“Blue Brightness” or “Blue Contrast”.
To be continued
Advanced Operations
The receiver has been designed to incorporate setup and
calibration standards established by the Imaging Science
Foundation (ISF). The ISF has developed carefully crafted,
industry-recognized standards for optimal video
performance and has implemented a training program for
technicians and installers to use these standards to obtain
optimal picture quality from the receiver. Accordingly,
Onkyo recommends that setup and calibration be
performed by an ISF Certified installation technician.
■ Game Mode*4*5*6
` Off
` On
If video signal delay occurs during playback on a video
component (i.e., game console), select the corresponding
input source and set the “Game Mode” setting to “On”.
The delay will decrease but in return the picture quality will
become poor.
■ Film Mode*4*6
` Video:
“Film Mode” detection is not applied and the input
signal is handled as a video source.
` Auto:
Detects whether the input signal is a video or a
movie. If it is a movie, the appropriate conversion is
applied.
The AV receiver will adjust to the picture source,
automatically converting it to the appropriate progressive
signal and reproducing the natural quality of the original
picture.
■ Edge Enhancement*4*6
` Off
` Low
` Mid
` High
With this setting, you can make the picture appear sharper.
■ Noise Reduction*4*6
` Off
` Low
` Mid
` High
With this setting, you can reduce noise appearing on the
screen. Select the desired level.
■ Mosquito NR*4*6*7
` Off
` Low
` Mid
` High
With Mosquito Noise Reduction, you can remove the
shimmering or haziness that sometimes appears around
objects in the picture. Mosquito noise can be an issue with
overly compressed MPEG content.
■ Random NR*4*6*7
` Off
` Low
` Mid
` High
With Random Noise Reduction, you can remove
indiscriminate picture noise, such as film grain.
■ Block NR*4*6*7
` Off
` Low
` Mid
` High
With Block Noise Reduction, you can remove the block
distortion that sometimes appears in the picture. Block
noise can be an issue with overly compressed MPEG
content.
En-75
■ Resolution*4*6*8*9*10
`Through:
Select this to pass video through the AV receiver at
the same resolution and with no conversion.
`Auto:
Select this to have the AV receiver automatically
convert video at resolutions supported by your TV.
`480p (480p/576p), 720p, 1080i, 1080p:
Select the desired output resolution.
`1080p/24:
Select this for 1080p output at 24 frames per second.
`4K Upscaling:
Select this for an output resolution four times that of
1080p. Depending on the resolution supported by
your TV, it will result in either 3840 × 2160 or 4096
× 2160 pixels.
You can specify the output resolution for the HDMI output
and have the AV receiver upconvert the picture resolution
as necessary to match the resolution supported by your TV.
This setting is available only when “Source” has been
selected in “Resolution” of the “Monitor Out” setting
(➔ page 59).
■ Brightness*1*4*6
`–50 to 0 to +50
With this setting, you can adjust the picture brightness.
“–50” is the darkest. “+50” is the brightest.
■ Contrast*1*4*6
`–50 to 0 to +50
With this setting, you can adjust contrast. “–50” is the
least. “+50” is the greatest.
■ Hue*1*4*6
`–50 to 0 to +50
With this setting, you can adjust the color hue between
“–50” and “+50”.
Advanced Operations
■ Saturation*1*4*6
` –50 to 0 to +50
With this setting, you can adjust saturation. “–50” is the
weakest color. “+50” is the strongest color.
■ Color Temperature*4*6
` Warm
` Normal
` Cool
With this setting, you can adjust the color temperature.
■ Gamma*4*6
` –3 to 0 to +3
With this setting, you can adjust the incoming picture’s
R (red), G (green), and B (blue) color signal in relation to
the output color signal.
■ Red Brightness*4*6
` –50 to 0 to +50
With this setting you can adjust the brightness of red color.
“–50” is the darkest. “+50” is the brightest.
■ Red Contrast*4*6
` –50 to 0 to +50
With this setting you can adjust the contrast of red color.
“–50” is the least. “+50” is the greatest.
■ Green Brightness*4*6
` –50 to 0 to +50
With this setting you can adjust the brightness of green
color. “–50” is the darkest. “+50” is the brightest.
■ Blue Contrast*4*6
` –50 to 0 to +50
With this setting you can adjust the contrast of blue color.
“–50” is the least. “+50” is the greatest.
Note
• “Picture Adjust” cannot be used when:
– The NET input selector is selected, or
– “Monitor Out” is set to “Sub” (➔ page 59).
• “Picture Adjust” can be used when the USB input selector is
selected; however, only when iPod/iPhone is connected and
Standard Mode or Extended Mode (Video) is selected.
*1 This procedure can also be performed on the remote controller
by using the Quick Setup (➔ page 53).
*2 When a 3D video source is input, “Wide Mode” is fixed to
“Full”.
*3 When “Metadata Compatible” is enabled (➔ page 66),
“Picture Mode” is fixed to “Direct”.
*4 When the “Picture Mode” setting is set to anything other than
“Custom”, this setting cannot be used.
*5 If the “Resolution” setting is set to “4K Upscaling”
(➔ pages 59, 75), this setting is fixed at “Off”.
*6 Press CLR if you want to reset to the default value.
*7 When the “Noise Reduction” setting is set to anything other
than “Off”, this setting cannot be selected.
*8 With some TVs, there may be no picture when this setting is
set to “4K Upscaling”.
*9 When “Resolution” is set to “1080p”, “1080p/24”, or “4K
Upscaling” while “Monitor Out” is set to “Analog”, the
video is output in 1080i.
*10 When “Resolution” is set to “Auto” while “Monitor Out” is
set to “Analog”, the video is output as “Through”.
Audio Selector
■ Audio Selector
`ARC:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
`HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI (HDMI
IN) and digital audio inputs (COAXIAL IN or
OPTICAL IN) have been assigned, HDMI input is
automatically selected as a priority.
`COAXIAL:
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
`OPTICAL:
This can be selected when OPTICAL IN has been
assigned as an input source. If both optical and HDMI
inputs have been assigned, optical input is
automatically selected as a priority.
`Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are both
digital and analog inputs.
Note
■ Green Contrast*4*6
` –50 to 0 to +50
With this setting you can adjust the contrast of green color.
“–50” is the least. “+50” is the greatest.
• This setting can be made only for an input source that is assigned
to HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET and USB input
selectors.
• When using the Whole House Mode, this setting cannot be
selected.
• With the Game2 input selector, “Analog” cannot be used.
*1 You can select “ARC” if you select the TV/CD input selector.
But you cannot if you’ve selected “Off” in the “Audio Return
Channel” setting (➔ page 81).
■ Blue Brightness*4*6
` –50 to 0 to +50
With this setting you can adjust the brightness of blue
color. “–50” is the darkest. “+50” is the brightest.
En-76
Advanced Operations
Setting the Incoming Digital Signal (Fixed
Mode)
■ Fixed Mode
` Off:
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
` PCM:
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the PCM
indicator will flash and noise may also be produced.
` DTS:
Only DTS (but not DTS-HD) format input signals
will be heard. If the input signal is not DTS, the dts
indicator will flash and there will be no sound.
When “HDMI”, “COAXIAL” or “OPTICAL” is selected
in the “Audio Selector” setting, you can then specify the
signal type in “Fixed Mode”.
Normally, the AV receiver detects the signal format
automatically. However, if you experience either of the
following issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS.
• If the beginnings of tracks from a PCM source are cut off,
try setting the format to PCM.
• If noise is produced when fast forwarding or reversing a
DTS CD, try setting the format to DTS.
2
Listening Mode Preset
1
2
3
Main Menu
4
“Setup”
5
Listening Mode Preset
You can assign a default listening mode to each input
source that will be selected automatically when you select
each input source. For example, you can set the default
listening mode to be used with Dolby Digital input signals.
You can select other listening modes during playback, but
the mode specified here will be resumed once the AV
receiver has been set to standby.
1
Use q/w to select the input source that you want to
set, and then press Enter.
The following menu appears.
5-1. Listening Mode Preset
Analog/PCM
Mono/Multiplex Source
2ch Source
Dolby D/Dolby D Plus/TrueHD
DTS/DTS-ES/DTS-HD
Other Multich Source
Default listening mode for analog and PCM sources.
BD/DVD
All Ch Stereo e r
Full Mono
PLllx Movie
Straight Decode
Straight Decode
Straight Decode
Use q/w to select the signal format that you want to
set, and then use e/r to select a listening mode.
Only listening modes that can be used with each input
signal format can be selected (➔ pages 41 to 48).
The “Last Valid” option means that the listening
mode selected last will be used.
The “Straight Decode” option means that straight
decoding listening mode (Dolby Digital, DTS, etc.) is
selected.
Note
• (North American models) For the “TUNER” input
selector, only “Digital” will be available.
• (Australian models) For the “TUNER” input selector, only
“Analog” will be available.
• For the “NET” or “USB” input selector, only “Digital” will
be available.
■ Analog/PCM/Digital
With this setting, you can specify the listening mode
used when an analog (CD, TV, LD, VHS, MD, turntable,
radio, cassette, cable, satellite, etc.) or PCM digital (CD,
DVD, etc.) audio signal is played.
■ Mono/Multiplex Source
With this setting, you can specify the listening mode
used when a mono digital audio signal is played (DVD,
etc.).
■ 2ch Source
With this setting, you can specify the listening mode
used when 2-channel (2/0) stereo digital sources, such as
Dolby Digital or DTS, are played.
Note
• The setting will be reset to “Off” when you change the setting in
“Audio Selector”.
En-77
Advanced Operations
■ Dolby D/Dolby D Plus/TrueHD
With this setting, you can specify the listening mode
used when Dolby Digital or Dolby Digital Plus format
digital audio signals are played (DVD, etc.). Specifies
the default listening mode for Dolby TrueHD sources,
such as Blu-ray or HD DVD (input via HDMI).
■ DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode
used when DTS or DTS-HD High Resolution format
digital audio signals are played (DVD, LD, CD, etc.).
Specifies the default listening mode for DTS-HD Master
Audio sources, such as Blu-ray or HD DVD (input via
HDMI).
■ Other Multich Source
Specifies the default listening mode for multichannel
PCM sources from HDMI IN such as DVD-Audio, and
DSD multichannel sources such as Super Audio CD.
Miscellaneous
1
2
Main Menu
3
4
“Setup”
5
Miscellaneous
Volume Setup
■ Volume Display
` Absolute:
Displayed range is Min, 0.5 to 99.5, Max.
` Relative(THX):
Displayed range is –QdB, –81.5dB to +18.0dB.
With this setting, you can choose how the volume level is
displayed.
The absolute value 82 is equivalent to the relative value
0 dB.
Note
• If the absolute value is set to 82, “82.0Ref” will appear on the
display and the THX indicator will flash.
■ Muting Level
` –QdB (fully muted), –50dB to –10dB in 10 dB steps.
This setting determines how much the output is muted when
the muting function is used (➔ page 51).
■ Maximum Volume
` Off, 50 to 99 (Absolute display)
` Off, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”.
En-78
■ Power On Volume
`Last, Min, 1 to 99 or Max (Absolute display)
`Last, –QdB, –81dB to +18dB (Relative display)
With this preference, you can specify the volume setting to
be used each time the AV receiver is turned on.
To use the same volume level that was used when the AV
receiver was turned off, select “Last”.
The “Power On Volume” setting cannot be set higher than
the “Maximum Volume” setting.
■ Headphone Level
`–12dB to 0dB to +12dB
With this setting, you can specify the headphone volume
relative to the main volume. This is useful if there’s a
volume difference between your speakers and your
headphones.
Advanced Operations
OSD Setup
12V Trigger A/B/C Setup
■ On Screen Display
` On
` Off
This preference determines whether operation details are
displayed on-screen when an AV receiver function is
adjusted.
Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
Depending on their type, when some components are
turned by using triggers A, B, and C, a large amount of
current may be drawn at once. To prevent this, you can
delay each trigger signal individually. Another application
of trigger delay is to eliminate the “thump” noise that’s
sometimes heard when a source component is turned on.
You can accomplish this by delaying the trigger signal for
your power amplifier, so that it’s the last component to be
turned on.
■ Language
` English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska, 中文
This setting determines the language used for the on-screen
menus.
■ Delay
` 0sec, 1sec, 2sec, 3sec:
When “0sec” is selected, the trigger signal is output
as soon as the input source is changed.
■ Screen Saver
` 3min, 5min, 10min
` Off
With this setting, you can set the time until the screen saver
activates itself. Once active, the screen saver will go off
and the screen will return to its previous state if the AV
receiver is operated in any way.
• By default, “12V Trigger A Setup” is set to “0sec”, “12V
Trigger B Setup” to “1sec”, and “12V Trigger C Setup” to
“2sec”.
• Use a miniplug cable to connect the AV receiver’s 12V
TRIGGER OUT A, B, or C jack to the 12 V trigger input of a
connected component.
Note
■ BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, AUX, TUNER, TV/CD, PHONO, NET, USB
` Off:
No trigger signal is output.
A 12-volt trigger signal is output when the connected
component is selected as the source for:
` Main, Zone 2, Main/Zone 2, Zone 3, Main/Zone 3,
Zone 2/Zone 3, Main/Zone 2/Zone 3, Zone 4,
Main/Zone 4, Zone 2/Zone 4, Main/Zone 2/Zone 4,
Zone 3/Zone 4, Main/Zone 3/Zone 4,
Zone 2/Zone 3/Zone 4, Main/Zone 2/Zone 3/Zone 4
Note
• By default, all input sources on the “12V Trigger A Setup” menu
are set to “Main”, those on “12V Trigger B Setup” are set to
“Main/Zone 2/Zone 3/Zone 4”, and those on “12V Trigger C
Setup” are set to “Zone 2”.
En-79
Hardware Setup
1
2
Main Menu
3
4
“Setup”
5
Hardware Setup
Multi Zone
■ Zone 2 Out, Zone 3 Out, Zone 4 Out
`Fixed:
The Zone 2/3/4 volume must be set on the amp in that
zone.
`Variable:
The Zone 2/3/4 volume can be set on the AV
receiver.
If you’ve connected your Zone 2/3/4 speakers to an amp
with no volume control, set the “Zone 2 Out”, “Zone 3
Out”, and “Zone 4 Out” setting, respectively, to
“Variable” so that you can set the volume, balance, and
tone of Zone 2/3 and volume of Zone 4 on the AV receiver.
■ Zone 2 Maximum Volume,
Zone 3 Maximum Volume,
Zone 4 Maximum Volume
`Off, 50 to 99 (Absolute display)
`Off, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume for
Zone 2/3/4.
■ Zone 2 Power On Volume,
Zone 3 Power On Volume,
Zone 4 Power On Volume
`Last, Min, 1 to 99 or Max (Absolute display)
`Last, –QdB, –81dB to +18dB (Relative display)
To be continued
Advanced Operations
This setting determines what the volume will be for
Zone 2/3/4 each time the AV receiver is turned on.
To use the same volume level as when the AV receiver was
last turned off, select “Last”.
The “Zone 2 Power On Volume”, “Zone 3 Power On
Volume”, and “Zone 4 Power On Volume” cannot be set
higher than the “Zone 2 Maximum Volume”, “Zone 3
Maximum Volume”, and “Zone 4 Maximum Volume”
setting.
Tuner
■ AM/FM Frequency Step (North American
models)
` 10kHz/200kHz:
` 9kHz/50kHz:
Select the frequency step according to your area.
■ AM Frequency Step (Australian models)
` 10kHz:
` 9kHz:
Select the frequency step according to your area.
For AM/FM tuning to work properly, you must specify the
AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be deleted.
HDMI
■ HDMI Control(RIHD)
` Off
` On
Turn this setting on to allow p-compatible
components connected via HDMI to be controlled by the
AV receiver (➔ page 112).
Note
• When the setting is set to “On” and the menu is closed, the names
of connected p-compatible components and “RIHD On”
are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the component,
it is displayed as “Player*” or “Recorder*”, etc. (“*” shows up
and indicates the number of components, when two or more are
received).
• When an p-compatible component is connected to the
AV receiver via an HDMI cable, the name of the connected
component is displayed on the AV receiver display. For example,
while you are watching TV broadcasting, if you operate a Blu-ray
Disc/DVD player (being powered on) with the remote control of
the AV receiver, the name of the Blu-ray Disc/DVD player will
be displayed on the AV receiver.
• Set it to “Off” when a connected piece of equipment is not
compatible or it is unclear whether the equipment is compatible
or not.
• If operation is not normal when set to “On”, change the setting to
“Off”.
• Refer to the connected component’s instruction manual for
details.
• When the “HDMI Control(RIHD)” setting is set to “On”, the
power consumption on standby mode slightly increases.
(Depending on the TV status, the AV receiver will enter standby
mode as usual.)
• The HDMI component (connected to HDMI IN 1/2/3/AUX
Input) selected for Zone 2 cannot be operated with the remote
controller through the AV receiver using RIHD function and also
cannot be operated on the TV connected to HDMI OUT MAIN
using CEC function.
• The HDMI component (connected to HDMI IN 1/2/3/AUX
Input) selected for Zone 2 can be operated on the TV in Zone 2
using CEC function.
• When the source equipment is connected with the u
connection, it may malfunction if “HDMI Control(RIHD)” is
set to “On”.
En-80
■ HDMI Through
`Off
`BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, AUX, TV/CD, PHONO:
Selects the input source for which the HDMI
Through function is enabled.
`Last:
The HDMI Through function is activated on the input
source selected at the time of setting the AV receiver
to standby mode.
When enabling the HDMI Through function, regardless of
whether the AV receiver is on or in standby, both audio
and video streams from an HDMI input will be output to
the TV or other components via HDMI connection. The
HDMI indicator will be dimly-lit in standby mode. Note
that the indicator may not light under certain conditions
(➔ page 58).
This setting is fixed to “Auto” automatically when the
above “HDMI Control(RIHD)” setting is set to “On”,
resulting in automatic input source selection.
Note
• Only an input source assigned to an HDMI IN via “HDMI Input”
setting is enabled (➔ page 60).
• The power consumption in standby mode will increase during the
HDMI Through function; however in the following cases, the
power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting fixed to “Auto”.
• This setting is set to “Off” automatically when the “HDMI
Control(RIHD)” setting is set to “Off”.
• This function is only available for the HDMI OUT MAIN jack.
Advanced Operations
■ Audio TV Out
` Off
` On
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV’s speakers.
Normally, this should be set to “Off”.
Note
• If “On” is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, “TV Speaker” appears on the AV receiver’s display by
pressing Display.
• When “HDMI Control(RIHD)” is set to “On”, this setting is
fixed to “Auto”.
• When Digital Processing Crossover Network is being used, this
setting is not available.
• With some TVs and input signals, no sound may be output even
when this setting is set to “On”.
• When “Audio TV Out” or “HDMI Control(RIHD)” is set to
“On” and you’re listening through your TV’s speakers
(➔ page 17), turning up the AV receiver’s volume control will
make the sound be output from the AV receiver’s front left and
right speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
• Listening mode cannot be changed when this setting is set to
“On” and the input source is not HDMI.
■ Audio Return Channel (ARC)
` Off
` Auto:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to HDMI OUT MAIN
of the AV receiver. To use this function, you must select
the TV/CD input selector and your TV must be ARC
capable. Default setting: “- - - -”
Note
• This setting is fixed to “- - - -” when the “HDMI
Control(RIHD)” setting is set to “Off”.
• This setting is set to “Auto” automatically when the “HDMI
Control(RIHD)” setting is set to “On” for the first time.
• If you set “Audio Return Channel” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” (➔ page 76).
After changing the settings of the “HDMI
Control(RIHD)”, “HDMI Through” or “Audio
Return Channel”, turn off the power on all connected
pieces of equipment and then turn them on again. Refer
to the user’s manuals for all connected pieces of
equipment.
■ Lip Sync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
En-81
■ InstaPrevue
These settings apply to “InstaPrevue” of the Home menu
(➔ page 49) and specify the preview display of HDMI
video streams.
Sub Window
`Multi:
Displays preview thumbnails all at once.
`Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with “Sub Window” set to “Multi”)
`Top, Bottom, Left, Right
(with “Sub Window” set to “Single”)
`Upper Left, Upper Right, Lower Left, Lower Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
• Depending on video signals, the picture may not be properly
rendered on the preview thumbnails of InstaPrevue.
Advanced Operations
Auto Standby
■ Auto Standby
` Off
` On
When “Auto Standby” is set to “On”, the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video signal
input.
“Auto Standby” will appear on the AV receiver’s display
and OSD 30 seconds before the Auto Standby comes on.
Default setting: On (Australian models), Off (North
American models)
Note
• Set to “On”, the Auto Standby function may activate itself during
playback with some sources.
• The Auto Standby function does not work when Zone 2/3/4 is on.
What’s DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you enter a
domain name such as www.onkyousa.com in your Web
browser, before accessing the site, your browser uses DNS
to translate this into an IP address, in this case
63.148.251.142.
■ MAC Address
This is the AV receiver’s MAC (Media Access Control)
address. This address cannot be changed.
■ DHCP
` Enable
` Disable
This setting determines whether or not the AV receiver
uses DHCP to automatically configure its IP Address,
Subnet Mask, Gateway, and DNS Server settings.
Note
Network
After modifying the network settings, you must confirm
the changes by executing “Save”.
This section explains how to configure the AV receiver’s
network settings manually.
If your router’s DHCP server is enabled, you don’t need to
change any of these settings, as the AV receiver is set to
use DHCP to configure itself automatically by default (i.e.,
DHCP is set to “Enable”). If, however, your router’s
DHCP server is disabled (you’re for example using static
IP), you’ll need to configure these settings yourself, in
which case, a knowledge of Ethernet networking is
essential.
What’s DHCP?
DHCP (Dynamic Host Configuration Protocol) is used by
routers, computers, the AV receiver, and other devices to
automatically configure themselves on a network.
• If you select “Disable”, you must configure the “IP Address”,
“Subnet Mask”, “Gateway”, and “DNS Server” settings
yourself.
■ IP Address
` Class A:
“10.0.0.0” to “10.255.255.255”
` Class B:
“172.16.0.0” to “172.31.255.255”
` Class C:
“192.168.0.0” to “192.168.255.255”
Enter a static IP address provided by your Internet Service
Provider (ISP).
Most routers use Class C IP addresses.
■ Subnet Mask
Enter the subnet mask address provided by your ISP
(typically 255.255.255.0).
■ Gateway
Enter the gateway address provided by your ISP.
En-82
■ DNS Server
Enter the DNS server address provided by your ISP.
■ Proxy URL
To use a Web proxy, enter its URL here.
■ Proxy Port
If you’re using a Web proxy, enter a proxy port number
here.
■ Network Standby
`On
`Off
This setting enables or disables control over the network.
When enabled, the NET indicator will be dimly-lit while
the AV receiver is in standby mode. Note that the indicator
may not light under certain conditions (➔ page 58).
Note
• When set to “On”, the power consumption slightly increases in
standby mode.
■ Update Notice
`Enable
`Disable
When this setting is enabled, you will be notified if a
firmware update via network is available.
Note
• Selecting “Never Remind me” on the notification window will
switch this setting to “Disable” (➔ page 22).
• For details on the update notification, see “If the “Firmware
Update Available” window appears.” (➔ page 22).
Initial Setup
If you skipped the initial setup wizard, for example on
first-time use, you can reaccess it from here.
See “Initial Setup” (➔ page 23).
Advanced Operations
Remote Controller Setup
1
2
Main Menu
3
4
“Setup”
Lock Setup
5
Remote Controller Setup
1
2
Main Menu
3
4
“Setup”
5
Lock Setup
Remote ID
With this preference, you can protect your settings by
locking the setup menus.
■ Remote ID
` 1, 2, or 3
When several Integra/Onkyo components are used in the
same room, their remote ID codes may overlap. To
differentiate the AV receiver from other components, you
can change its remote ID from “1”, to “2” or “3”.
■ Setup
` Locked
` Unlocked
When “Locked” is selected, the setup menus will be
locked and you cannot change any setting.
Note
• If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
Changing the remote controller’s ID
1
While holding down Receiver, press and hold
down Q Setup until the Receiver lights (about 3
seconds).
2
Use the number buttons to enter ID 1, 2, or 3.
Receiver flashes twice.
Remote Mode Setup
See “Looking up for Remote Control Codes”
(➔ page 91).
En-83
Advanced Operations
Multi Zone
Main room
Main room
In addition to the main listening room, you can also enjoy
playback in the other room, or as we call Multi Zone. And,
you can select a different source for each room.
Making Multi Zone Connections
TV
TV
AV receiver
AV receiver
There are two ways you can connect Zone speakers:
1. Connect them directly to the AV receiver.
2. Connect them to an additional amplifier.
Connecting Your Zone Speakers Directly to
the AV receiver
This setup allows you to select different sources for Main
room and Zone 2/3/4. This is called Powered Zone, as the
Zone 2/3/4 speakers are powered by the AV receiver.
To use this setup, you must activate the Powered
Zone 2/3/4 setting (➔ page 63).
Zone 4
Zone 2
R
L
R
L
Note
Main room
• With this setup, the volume of Zone 2/3/4 is controlled by the AV
receiver.
• When Powered Zone 2 is used, playback in the main room is
reduced to 7.2 channels.
• When Powered Zone 3 is used, playback in the main room is
reduced to 5.2 channels.
• When Powered Zone 4 is used, playback in the main room is
reduced to 3.2 channels.
TV
AV receiver
Zone 3
R
L
En-84
Advanced Operations
Connecting the Zone Speakers to an
Additional Amplifier
Zone 2 Video Output
Note
This setup allows 9.2-channel playback in your main
listening room and 2-channel stereo playback in
Zone 2/3/4.
Main room
• With the default settings, the Zone 2/3/4 volume must be set on
the Zone 2/3/4 amplifier. If your Zone 2/3/4 amplifier has no
volume control, change the setting so that you can set the
Zone 2/3/4 volume on the AV receiver. See “Multi Zone”
(➔ page 79).
Connecting Powered Subwoofers in
Zone 2/3/4
TV
This setup allows you to use powered subwoofers in
Zone 2/3/4.
AV receiver
The on-screen information appears on the TV screen
in Zone 2 by connecting the TV to HDMI OUT
ZONE 2 of the AV receiver with HDMI cable.
The AV receiver allows you to enjoy the composite video
and HDMI audio/video in Zone 2 by connecting the TV of
Zone 2 to the respective output jacks.
Main room
TV
Main room
TV
AV receiver
AV receiver
or
Zone 2
Zone 4
IN
R
L
IN
R
Zone 2
L
TV
Receiver/
integrated amp
Receiver/
integrated amp
Zone 2
Zone 4
LINE INPUT
LINE INPUT
Zone 3
Powered Subwoofer
Powered Subwoofer
IN
R
L
Zone 3
LINE INPUT
Receiver/
integrated amp
Powered Subwoofer
En-85
Note
• If you use HDMI OUT ZONE 2, make sure to set “Zone 2
HDMI” to “Use” (➔ page 59).
• Video and audio signals from an HDMI input will be output to
HDMI OUT ZONE 2.
• The ZONE 2 OUT V jack outputs video of components
connected to composite video only.
• The information of connected component appears on a TV in
Zone 2 by pressing Display.
Advanced Operations
2
Setting the Zone 2/3/4 Out
See “Multi Zone” (➔ page 79).
Tip
■ Operating on the AV receiver
Master Volume
■ Operating on the remote controller
To control Zone 2/3/4, you must press Zone on the remote
controller first.
Zone turns red while Zone 2 is on, and green while Zone 3
is on, and amber while Zone 4 is on.
8Receiver
Zone
Input selector buttons
Zone 4, Off
Input selector buttons
Tip
To turn on Zone 2/3/4 and select an input source,
press Zone 2, Zone 3, or Zone 4 followed by an
input selector button within 8 seconds.
Zone 2/3/4 turns on, the Z2, Z3, or Z4 indicator lights
on the AV receiver’s display.
1
To select the same source as the main room’s, press
Zone 2, Zone 3, or Zone 4 twice. “Zone 2
Selector: Source”, “Zone 3 Selector: Source”, or
“Zone 4 Selector: Source” appears on the AV
receiver’s display.
2
Adjusting the Volume for Zones
■ Operating on the remote controller
1
2
Press Zone repeatedly.
Use VOL q/w.
■ Operating on the AV receiver
Press Zone 2, Zone 3, or Zone 4 (the Z2/Z3/Z4
indicator on the AV receiver’s display flashes).
VOLq/w
2
Use Master Volume control within 8 seconds.
Press Zone repeatedly, then point the remote
controller at the AV receiver and press 8Receiver.
Zone 2/3/4 turns on, the Z2, Z3, or Z4 indicator lights
on the AV receiver’s display.
• The corresponding trigger output goes high (+12 V).
• The corresponding trigger output goes high (+12 V).
To select AM or FM, press Zone 2, Zone 3, or
Zone 4 and the Tuner input selector repeatedly.
Tip
• The corresponding trigger output goes low (0 volts).
1
Tip
Tip
To turn off Zone 2/3/4, press Zone repeatedly,
followed by 8Receiver.
The zone is turned off.
Muting
• The Whole House Mode function shares the input source of main
room with Multi Zone (➔ page 51).
1
3
• The corresponding trigger output goes low (0 volts).
Controlling Multi Zone Components
Zone 2, Off
Tone
–, +
Zone 3, Off
To turn off Zone 2/3/4, press Off for each Zone.
The zone is turned off.
To select an input source for Zone 2/3/4, press Zone
repeatedly, followed by an Input Selector button.
To select AM or FM, press Zone and the Tuner input
selector repeatedly.
En-86
If your Zone 2/3/4 speakers are connected to a receiver or
integrated amplifier in Zone 2/3/4, use its volume control
to adjust the volume.
Advanced Operations
Muting Zones
■ Operating on the remote controller
1
Press Zone repeatedly, and then press Muting.
Tip
• To unmute, press Zone followed by Muting again. Zones can
also be unmuted by adjusting the volume.
Adjusting the Tone and Balance of Zone 2/3
1
2
On the AV receiver, press Zone 2 or Zone 3.
3
Use – or + to adjust the bass, treble or balance.
• You can boost or cut the bass or treble from –10 dB
to +10 dB in 2 dB steps.
• You can adjust the balance from 0 in the center to
+10 dB to the right or +10 dB to the left in 2 dB
steps.
Press the AV receiver’s Tone repeatedly to select
“Bass”, “Treble” or “Balance”.
Note
• ZONE 2 PRE/LINE OUT and FRONT WIDE/ZONE 2 L/R
output 2ch PCM and analog input sources. To listen to the PCM
source, you need to make an HDMI connection (➔ page 17). If
no sound is heard when an input source is selected, check if the
source is connected to an analog input and HDMI input.
• Only analog input sources are output by the ZONE 3/4
PRE/LINE OUT, FRONT HIGH/ZONE 3 L/R, and SURR
BACK/ZONE 4 L/R terminals. Digital input sources are not
output. If no sound is heard when an input source is selected,
verify that the source is connected to an analog input.
• (North American models) You can select different radio
stations for the main room and Zone 2 by connecting the supplied
antennas respectively (➔ page 20).
• (North American models) When the main room and Zone 2
share the same input source, if the input selector of the main room
is Tuner, you cannot select different radio stations for the main
room and Zone 2 respectively.
• (Australian models) You cannot select different AM or FM
radio stations for your main room and Zone 2/3/4. The same
AM/FM radio station will be heard in each room. Namely, if you
have selected an FM station for the main room, that station will
also be output in Zone 2/3/4.
• You cannot select different radio stations for Zone 2, Zone 3, and
Zone 4 respectively.
• If Zone 2 and the main room share the same input source, only an
analog input signal is output.
• If an HDMI component selected in Zone 2 outputs the sound
other than PCM, the sound is not output from FRONT
WIDE/ZONE 2 and ZONE 2 PRE/LINE OUT.
• Both audio and video outputs from an HDMI component may
interrupt when the main room and Zone 2 are set to share the
same source or not.
• When you have selected NET or USB as input selector, the last
selector selected will be set for Main room and Zone 2/3/4.
• When Zone 2/3/4 is activated and its input selector is selected, the
power consumption of standby mode slightly increases.
• While Zone 2/3/4 is on, u functions will not work.
• The component connected to HDMI input other than HDMI IN
1/2/3/AUX Input is selected as an input source for Zone 2, the
linked operations of p may not work properly. In this
case, set the linked operations to Off on the source component.
• When setting the AV receiver to standby mode while Zone 2/3/4
is active, the Z2, Z3, or Z4 indicator is dimly lit.
• Even if you repeatedly press the remote controller’s Zone to
select zones, the last zone selection will be retained once you
have switched to other components by pressing other Remote
Mode after pressing Zone.
• The Zone 2/3 level, balance, and tone functions have no effect on
the ZONE 2/3 PRE/LINE OUT jacks when the “Zone 2 Out”
or “Zone 3 Out” setting is set to “Fixed” (➔ page 79).
• The Zone 4 volume function has no effect on ZONE 4
PRE/LINE OUT when the “Zone 4 Out” setting is set to
“Fixed” (➔ page 79).
En-87
Using the 12V Triggers
The 12V triggers A, B, and C can be used to turn on 12V
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so that
they activate themselves once a connected component is
selected as the input source for the main room, Zone 2,
Zone 3, Zone 4, or any combination of rooms. When
triggered, the output from a 12V TRIGGER OUT goes
high (+12 volts and 150 milliamperes max. at 12V
TRIGGER OUT A; +12 volts and 25 milliamperes max.
at 12V TRIGGER OUT B and C).
See “12V Trigger A/B/C Setup” (➔ page 79).
Hookup
• Use a miniplug cable to connect the AV receiver’s 12V
TRIGGER OUT A, B, or C jack to the 12 V trigger
input of a connected component.
Advanced Operations
Using the Remote Controller in
Zone and Multiroom Control Kits
To control the AV receiver with the remote controller
while you’re in Zone, you’ll need a commercially available
multiroom remote control kit for each zone.
• Multiroom kits are made by Niles and Xantech.
These kits can also be used when there isn’t a clear line of
sight to the AV receiver’s remote sensor, such as when it’s
installed inside a cabinet.
The miniplug cable from the connecting block should be
connected to the AV receiver’s IR IN A or B jack, as
shown below. The IR IN A and B jacks are identical. Up to
two IR receivers can be connected.
From the connecting block
Miniplug cable
Using a Multiroom Kit with Other
Components
In this setup, an IR emitter is connected to the AV
receiver’s IR OUT jack and placed in front of the other
component’s remote control sensor. Infrared signals
received at the AV receiver’s IR IN A or B jack are fed
through to the other component via the IR emitter. Signals
picked up by the AV receiver’s remote control sensor are
not output.
Using a Multiroom Kit with Zone
In this setup, the IR receiver in Zone picks up the infrared
signals from the remote controller and feeds them through
to the AV receiver in the main room via the connecting
block.
IR IN
A or B
IR OUT
AV receiver
Signal flow
Using a Multiroom Kit with a Cabinet
Connecting
block
AV receiver
IR emitter
IR IN A or B
Connecting
block
IR
receiver
In this setup, the IR receiver picks up the infrared signals
from the remote controller and feeds them to the AV
receiver located in the cabinet via the connecting block.
IR receiver
Remote controller
Other component
Signal flow
Connecting
block
Remote controller
Main room
Zone
IR
receiver
IR IN
A or B
The IR emitter should be connected to the AV receiver’s
IR OUT jack, as shown below.
From the connecting block
Miniplug cable
Other component
Signal flow
Remote control sensor
Inside
cabinet
Remote controller
AV receiver
Emitter
Signal flow
IR emitter
Miniplug
Signal flow
En-88
Controlling Other Components
iPod/iPhone Playback
via Onkyo Dock
Using the Onkyo Dock
The Dock is sold separately. Models sold are different
depending on the region.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
http://www.onkyo.com
Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
For supported iPod/iPhone models, see the instruction
manual of the Onkyo Dock.
RI Dock
With the RI Dock, you can easily play the music of your
iPod/iPhone, or watch the slideshows and videos of your
iPod/iPhone on a TV. In addition, the on-screen display
(OSD) allows you to view, navigate, and select your
iPod/iPhone model’s contents on your TV, and with the
supplied remote controller, you can control your
iPod/iPhone from the comfort of your sofa. You can even
use the AV receiver’s remote controller to operate your
iPod/iPhone.
Note
• Enter the appropriate remote control code before using the AV
receiver’s remote controller for the first time (➔ page 93).
• Connect the RI Dock to the AV receiver with an u cable
(➔ page 21).
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• Set the AV receiver’s Input Display to “DOCK” (➔ page 50).
■ System Function
Depending on your iPod/iPhone model and generation,
some of the linked operations may not be available.
Auto Power On
If you press the remote controller’s 1 (Playback) while
the AV receiver is on standby, the AV receiver will
automatically turn on, select your iPod/iPhone as the input
source, and your iPod/iPhone will start playback.
Direct Change
If you start iPod/iPhone playback while listening to another
input source, the AV receiver will automatically switch to
the input to which the RI Dock is connected.
System Off
When you turn off the AV receiver, the RI Dock turns off
automatically.
En-89
Other Remote Operations
You can use the remote controller that came with the AV
receiver to control other iPod/iPhone functions. The
available functionality depends on the AV receiver.
Note
• If you use your iPod/iPhone with any other accessories,
iPod/iPhone playback detection may not work.
iPod Alarm
If you use the Alarm function on your iPod to start
playback, the AV receiver will turn on at the specified time
and select your iPod as the input source automatically.
Note
• This linked operation won’t work while a video is being played
or when the sound set for the alarm is a built-in sound (Beep).
• This linked operation won’t work with models on which music
files cannot be used to set the alarm sound.
■ Operating Notes
• Use the AV receiver’s volume control to adjust the playback
volume.
• While your iPod/iPhone is inserted in the RI Dock, its volume
control has no effect.
• If you do adjust the volume control on your iPod/iPhone while
it’s inserted in the RI Dock, be careful that it’s not set too loud
before you reconnect your headphones.
Controlling Other Components
■ u Dock operation
Controlling Your iPod/iPhone
Press the appropriate Remote
Mode button first.
By pressing the Remote Mode button that’s been
programmed with the remote control code for your Dock,
you can control your iPod/iPhone in the Dock with the
buttons described further in this section.
See “Entering Remote Control Codes” for details on
entering a remote control code (➔ page 92).
See the Dock’s instruction manual for more information.
Available buttons
e Display*2
b q/w/e/r, Enter
f 8Source*3
Playlist e/r
e
f
RI Dock
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• 8Source may not work with a remote control code
(without u). In this case, make an u connection and
enter the remote control code 81993 (with u).
■ With the RI Control
Make an u connection and enter the remote control code
81993 (with u).
• Set the AV receiver’s Input Display to “DOCK”
(➔ page 50).
a Top Menu*1
g
h
i
a
j
b
■ Without the RI Control
You must enter the remote control code 82990 first
(➔ page 93).
c
d
k
En-90
g Muting
c 1, 3, 2, 5, 4,
7, 6
h Album +/–
d Repeat
Random
j Menu
k Mode*4
i VOL q/w
• With some iPod/iPhone models, generations and RI Docks,
certain buttons may not work as expected.
• For detailed operation of iPod/iPhone, please refer to the
instruction manual of the RI Dock.
*1 Top Menu works as the mode button when used with the DSA2 RI Dock.
*2 Display turns on the backlight for a few seconds.
*3 This button does not turn the Onkyo DS-A2 or DS-A2X RI
Dock on or off. Also, your iPod/iPhone may not respond the
first time you press this button, in which case you should press
it again. This is because the remote controller transmits the On
and Standby commands alternately, so if your iPod/iPhone is
already on, it will remain on when the remote controller
transmits the On command. Similarly, if your iPod/iPhone is
already off, it will remain off when the remote controller
transmits the Off command.
*4 Resume mode
With the Resume function, you can resume playback of the
song that was playing when you removed your iPod/iPhone
from the Onkyo DS-A2 RI Dock.
Controlling Other Components
Controlling Other
Components
You can use the AV receiver’s remote controller to control
your other AV components, including those made by other
manufacturers. This section explains how to enter the
remote control code for a component that you want to
control: DVD, TV, CD, etc.
See “Learning Commands” for learning commands
directly from another component’s remote controller
(➔ page 96).
See “Using Normal Macros” for programming Activities
to perform a sequence of remote control actions
(➔ page 97).
Preprogrammed Remote Control
Codes
The following Remote Mode buttons are preprogrammed
with remote control codes for controlling the components
listed. You do not need to enter a remote control code to
control these components.
For details on controlling these components, see the
indicated pages.
Looking up for Remote Control Codes
You can look up for an appropriate remote control code
from the on-screen menu.
You need to connect your TV to the HDMI output
(HDMI OUT MAIN) to make the following on-screen
setting.
1
2
3
Press Receiver followed by Home.
4
Use q/w to select “Remote Mode Setup”, and then
press Enter.
5
Use q/w to select a remote mode, and then press
Enter.
The menu of category selection appears.
6
Use q/w to select a category, and then press Enter.
The keyboard screen for brand name input appears.
7
Use q/w/e/r to select a character, and then press
Enter.
Repeat this step for the first three characters of the
brand name.
When you have entered the 3rd character, select
“Search” and press Enter.
A list of brand names is retrieved.
If the desired brand name is not found:
Use r to select “Not Listed”, and then press Enter.
The keyboard screen for brand name input appears.
8
Use q/w to select a brand, and then press Enter.
A remote control code with its instructions are
displayed. Follow the procedure.
BD/DVD Integra/Onkyo Blu-ray Disc player
(➔ page 94)
TV/CD
Integra/Onkyo CD player (➔ page 93)
STB/DVR Apple TV
Use e/r to select “Setup”, and then press Enter.
Use q/w to select “Remote Controller Setup”, and
then press Enter.
En-91
9
If you can control the component, use q/w to select
“OK”, and then press Enter.
The on-screen menu returns to the “Remote Mode
Setup” front screen.
If you cannot control the component, use q/w to
select “Try Next Code” and press Enter.
The next code is displayed.
Controlling Other Components
Entering Remote Control Codes
Remapping Colored Buttons
You’ll need to enter a code for each component that you
want to control.
You can change the configuration of colored buttons, with
which Remote Mode buttons are preset.
1
Look up the appropriate remote control code in the
separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
1
2
While holding down the Remote Mode button to
which you want to assign a code, press and hold
down Display (about 3 seconds).
The Remote Mode button lights.
While holding down the Remote Mode button that
you want to program, press and hold down A (Red)
until the Remote Mode button lights (about 3
seconds).
You can only change colored buttons for components
whose codes belong to categories of the Remote
Control Codes list (BD/DVD player, TV, cable set-top
box, etc).
2
Within 30 seconds, press the colored buttons in the
order that you want to reassign them.
The button presses are assigned to each button from
left to right. The Remote Mode button flashes twice,
indicating that the sequence has been successfully
assigned. If the sequence is not successfully assigned,
the Remote Mode button will flash once slowly.
Note
• Remote control codes cannot be entered for Receiver and
the multi zone button.
• Only TV remote control codes can be entered for TV.
• Except for Receiver, TV, and the multi zone button,
remote control codes from any category can be assigned for
the Remote Mode buttons. However, these buttons also
work as input selector buttons (➔ page 25), so choose a
Remote Mode button that corresponds with the input to
which you connect your component. For example, if you
connect your CD player to the CD input, choose TV/CD
when entering its remote control code.
3
Within 30 seconds, use the number buttons to enter
the 5-digit remote control code.
The Remote Mode button flashes twice.
If the remote control code is not entered successfully,
the Remote Mode button will flash once slowly.
Tip
• To reset the Remote Mode buttons to their default settings, see
“Resetting the Remote Mode Buttons” (➔ page 93).
Note
• If any other button than the colored buttons is pressed, the
operation will be cancelled.
• This operation cannot be done while the AV receiver is in
Receiver mode or when Zone 2/3/4 is active.
Note
• Though the provided remote control codes are correct at the time
of release, they are subject to change.
En-92
Controlling Other Components
` 70868:
Onkyo MD recorder without u
` 71323:
Onkyo CD recorder without u
` 82990:
Onkyo Dock without u
Remote Control Codes for
Integra/Onkyo Components Connected
via RI
Integra/Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
1
Make sure the Integra/Onkyo component is
connected with an u cable and an analog audio
cable (RCA).
See “Connecting Integra/Onkyo RI Components” for
details (➔ page 21).
2
Enter the appropriate remote control code for a
Remote Mode button, by referring to the previous
section.
`42157:
Onkyo cassette tape deck with u
`81993:
Onkyo Dock with u
3
Press the Remote Mode button, point the remote
controller at the AV receiver, and operate the
component.
Controlling Integra/Onkyo components without u
If you want to control an Integra/Onkyo component by
pointing the remote controller directly at it, or you want to
control an Integra/Onkyo component that’s not connected
via u, use the following remote control codes:
` 30627:
Integra/Onkyo DVD player without u
` 71817:
Integra/Onkyo CD player without u
` 32900/33100/33500:
Integra/Onkyo Blu-ray Disc player
` 32901/33104/33504:
Integra/Onkyo HD DVD player
Resetting the Remote Mode Buttons
You can reset a Remote Mode button to its default
remote control code.
1
While holding down the Remote Mode button that
you want to reset, press and hold down Home until
the Remote Mode button lights (about 3 seconds).
2
Within 30 seconds, press the Remote Mode button
again.
The Remote Mode button flashes twice, indicating
that the button has been reset.
Each Remote Mode button is preprogrammed with a
remote control code. When a button is reset, its
preprogrammed code is restored.
Controlling Other Components
By pressing the Remote Mode button that’s been
programmed with the remote control code for your
component, you can control your component as described
below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
(➔ page 92).
Controlling a TV
TV is preprogrammed with the remote control code for
controlling a TV that supports the p*1 (limited to
some models). The TV must be able to receive remote
control commands via p and be connected to the
AV receiver via HDMI. If controlling your TV via
p doesn’t work very well, program your TV’s
remote control code into TV and use the TV remote mode
to control your TV.
Use the following remote control codes:
`11807/13100/13500:
TV with p
Note
• The learning command is also reset.
Resetting the Remote Controller
You can reset the remote controller to its default settings.
1
While holding down Receiver, press and hold
down Home until Receiver lights (about 3
seconds).
2
Within 30 seconds, press Receiver again.
Receiver flashes twice, indicating that the remote
controller has been reset.
En-93
Controlling Apple TV
By programming the supplied remote controller with the
appropriate remote control code, you can use it to operate
your Apple TV.
Use the following remote control codes:
`02615:
Apple TV
Controlling Other Components
■ TV operation
Controlling MHL-Enabled Mobile Device
Press the appropriate Remote
Mode button first.
By programming the supplied remote controller with the
appropriate remote control code, you can use it to operate
your MHL-enabled mobile device.
Connect your MHL-enabled mobile device to the AUX
Input MHL jack. We advise you to program the remote
control code on the AUX button.
Use the following remote control codes:
(North American models)
` 33101:
MHL-enabled mobile device
(Australian models)
` 32910:
MHL-enabled mobile device
Note
• With some mobile devices, reliable operation cannot be
guaranteed.
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
BD/DVD is preprogrammed with the remote control code
for controlling a component that supports the p*1
(limited to some models). The component must be able to
receive remote control commands via p and be
connected to the AV receiver via HDMI.
Use the following remote control codes:
` 32910/33101/33501/31612:
Blu-ray Disc/DVD player with p
Available buttons
a 8, Input, TV VOL q/w
b Guide
h
i
Number: +10*1
c q/w/e/r
Enter
h Display
j Muting
d Setup
k CH +/–
l PREV CH
e 1, 3, 2, 5, 4,
7, 6*1
f A (Red)*1
B (Green)*1
m Return
n CLR
C (Yellow)*1
j
k
a
D (Blue)*1
■ Blu-ray Disc/HD DVD player operation
Available buttons
b Top Menu
b
l
c
d
m
c q/w/e/r
Enter
e
The p supported by the AV receiver is the CEC system
control function of the HDMI standard.
g
n
En-94
g Number: 1 to 9, 0
Number: +10*1
h Display
d Setup
i 8Source
e 1, 3, 2, 5, 4,
7, 6
j Muting
k CH +/–
f A (Red)
B (Green)
f
*1
g Number: 1 to 9, 0
Disc +/–
C (Yellow)
l Menu
m Return
D (Blue)
n CLR
Controlling Other Components
Press the appropriate Remote
Mode button first.
■ DVD player/DVD recorder operation
■ Satellite receiver/Cable receiver operation
Available buttons
Available buttons
b Top Menu
g Number: 1 to 9, 0
Number: +10*1
c q/w/e/r
Enter
h
i
k
b
l
c
d
m
g Number: 1 to 9, 0
Number: +10
h Display
c q/w/e/r
Enter
d Setup
i 8Source
d Setup
i 8Source
e 1, 3, 2, 5, 4,
7, 6
j Muting
k CH +/–
e 1, 3, 2, 5, 4,
7, 6
j Muting
k CH +/–
f A (Red)
B (Green)
l PREV CH
m Return
Disc +/–
f A (Red)*1
B (Green)
j
b Guide
C (Yellow)*1
l Menu
m Return
D (Blue)*1
n CLR
C (Yellow)
h Display
n CLR
D (Blue)
■ CD player/CD recorder/MD recorder operation
■ VCR/PVR operation
Available buttons
Available buttons
b Guide
h Display
c q/w/e/r
Enter
i 8Source
d Setup
j Muting
k CH +/–
e 1, 3, 2, 5, 4,
7, 6
l PREV CH
m Return
g Number: 1 to 9, 0
Number: +10
n CLR
c q/w/e/r
Enter
g Number: 1 to 9, 0
Number: +10
d Setup
h Display
e 1, 3, 2, 5, 4,
7, 6
i 8Source
f Search
Repeat
j Muting
k Disc +/–
n CLR
Random
■ Cassette tape deck operation
e
Available buttons
f
e 1, t (Reverse
Playback), 2, 5, 4,
7, 6
Mode
Note
i 8Source
j Muting
g
n
En-95
• With some components, certain buttons may not work as
expected, and some may not work at all.
• See “Controlling Your iPod/iPhone” about the operation of
iPod/iPhone (➔ page 90).
*1 The p function is not supported. The p
supported by the AV receiver is the CEC system control
function of the HDMI standard.
Controlling Other Components
If the command is learned successfully, the Remote
Mode button flashes twice.
Learning Commands
O
N
D
DV
U
O
R
D
-1
D
C
IS
C
G
-2
EO
VID
EO
TA
IM
LE R
SE E
T UN
PU T
IN
PE
W
PO
ER
D
DV
SL
EE
VID
P
D
P
R O
TO H
C P
M
ER
RE
SUOD
M
Within about
4 inches (10 cm)
TU
H
I-CT
ULTPU
M IN
C
D
S
ER E
N PR
ET
C
H
SE
L
STE
TEON
T
U
TIN
G
VO
LU
M
E
The AV receiver’s remote controller can learn the
commands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s remote
controller, the supplied remote controller can learn it and
then reproduce the exact same command when its 1 is
pressed in CD remote mode.
This is useful when some buttons don’t work as expected
though you entered the appropriate remote control code
(➔ page 92).
Supplied remote
controller
8Receiver
4
Remote Mode
To learn more commands, repeat steps 2 and 3.
Press any Remote Mode button when you’ve
finished. The Remote Mode button flashes twice.
Note
1
While holding down the Remote Mode button for
the mode in which you want to use the command,
press and hold down 8Receiver until the Remote
Mode button lights (about 3 seconds).
2
On the supplied remote controller, press the
button to which you want to assign the new
command.
3
Point the remote controllers at each other, within
about 4 inches (10 cm) apart, and then press and
hold the button whose command you want to
acquire until the Remote Mode button flashes.
• The following buttons cannot learn new commands: 8Receiver,
All Off, My Movie, My TV, My Music, Remote Mode,
Mode.
• The remote controller can learn approximately 70 to 90
commands, although this will be less if commands that use a lot
of memory are learned.
• Remote controller buttons such as Play, Stop, and Pause are
preprogrammed with commands for controlling Integra/Onkyo
CD players, cassette decks, and DVD players. However, they can
learn new commands, and you can restore the preprogrammed
commands at any time by resetting the remote controller
(➔ page 93).
• To overwrite a previously acquired command, repeat this
procedure.
• Depending on the remote controller used, some buttons may not
respond as expected, or the learning process itself may not be
possible.
• Only commands from infrared remote controllers can be
acquired.
• When the remote controller runs out of batteries, all commands
acquired will be lost and will have to be learned all over again.
Therefore, do not discard your other remote controllers.
En-96
■ Deleting Acquired Commands
1. While holding down the Remote Mode button for the
mode from which you want to delete a command, press
and hold down 8TV until the Remote Mode button
lights (about 3 seconds).
2. Press the Remote Mode button or the button from
which you want to delete the command.
The Remote Mode button flashes twice.
When you press the Remote Mode button, all
commands learned in that mode will be deleted.
Controlling Other Components
3
Using Normal Macros
You can program the remote controller’s Activities to
perform a sequence of remote control actions.
Example:
To play a CD you typically need to perform the following
actions:
1. Press Receiver to select the Receiver remote
controller mode.
2. Press 8Receiver to turn on the AV receiver.
3. Press TV/CD to select the TV/CD input source.
4. Press 1 to start playback on the CD player.
You can program Activities so that all four actions are
performed with just one button press.
When you’ve finished, press Activities again.
Activities button flashes twice.
If you enter 32 commands, the process will finish
automatically.
Note
• Mode cannot be operated during the macro-making process.
• Once you assign new macro commands, the previously registered
macro will no longer work. If you wish to retrieve it, you will
have to reassign the commands with the macro-making.
Running Macros
1
Making Macros
Each Activities can store one macro, and each macro can
contain up to 32 commands.
Press My Movie, My TV, or My Music.
The commands in the macro are transmitted in the
order in which they were programmed. Keep the
remote controller pointed at the AV receiver until all
of the commands have been transmitted.
Macros can be run at any time, regardless of the
current remote controller mode.
Deleting Macros
All Off
My Movie,
My TV,
My Music
Receiver
1
2
While holding down Home, press and hold down
All Off until All Off lights (about 3 seconds).
Press All Off again.
All Off flashes twice.
Note
1
2
While holding down Receiver, press and hold
down My Movie, My TV, or My Music until
My Movie, My TV, or My Music lights (about 3
seconds).
Press the buttons whose actions you want to
program into the macro in the order you want
them performed.
For the CD example above, you would press the
following buttons: 8Receiver, TV/CD, 1.
• When Normal macros are deleted, Activities are restored to their
default settings, namely the Easy macro commands
(➔ page 52).
• When using Normal macros, Easy macros cannot be used, which
includes changing the source components.
En-97
Appendix
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact the dealer from whom you purchased this
unit.
If you can’t resolve the issue yourself, try resetting the
AV receiver before contacting the dealer from whom
you purchased this unit.
To reset the AV receiver to its factory defaults, turn it
on and, while holding down CBL/SAT, press
8On/Standby. “Clear” will appear on the AV
receiver’s display and the AV receiver will enter
standby mode.
The on-screen information appears only on a TV that
is connected to HDMI outputs. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
Receiver
Home
To reset the remote controller to its factory defaults,
while holding down Receiver, press and hold down
Home until Receiver lights (about 3 seconds). Within
30 seconds, press Receiver again.
■ There’s no sound, or it’s very quiet
Make sure that the digital input source is selected
properly.
62
Make sure that all audio connecting plugs are pushed 16
in all the way.
Power
■ Can’t turn on the AV receiver
Make sure that the power cord is properly plugged
into the wall outlet.
Make sure that the inputs and outputs of all
components are connected properly.
—
Unplug the power cord from the wall outlet, wait five —
seconds or more, then plug it in again.
■ The AV receiver turns off unexpectedly
The AV receiver will automatically enter standby
82
mode when Auto Standby has been set and launches.
■ The AV receiver turns off and after restoring the
power, it turns off again
Note that resetting the AV receiver will delete your radio
presets and custom settings.
Audio
The protection circuit has been activated. Remove the 12
power cord from the wall outlet immediately. Make
sure that all speaker cables and input sources are
properly connected, and leave the AV receiver with
its power cord disconnected for 1 hour. After that,
reconnect the power cord and turn the power on. If
the AV receiver turns off again, unplug the power
cord and contact the dealer from whom you
purchased this unit.
Caution: If “CHECK SP WIRE” appears on the AV
receiver’s display, the speaker cables may be
shorting.
WARNING
If smoke, smell or abnormal noise is produced by the AV
receiver, unplug the power cord from the wall outlet
immediately and contact the dealer from whom you
purchased this unit.
En-98
17-21
Make sure that the polarity of the speaker cables is
12
correct, and that the bare wires are in contact with the
metal part of each speaker terminal.
Make sure that the input source is properly selected.
25
Make sure that the speaker cables are not shorting.
12
Check the volume. The AV receiver is designed for —
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
If the MUTING indicator is flashing on the AV
receiver’s display, press the remote controller’s
Muting button to unmute the AV receiver.
51
While a pair of headphones is connected to the
52
Phones jack, no sound is output from the speakers.
If there’s no sound from a DVD player connected to
an HDMI IN, check the DVD player’s output
settings, and be sure to select a supported audio
format.
—
Check the digital audio output setting on the
connected device. On some game consoles, such as
those that support DVD, the default setting is off.
—
With some DVD-Video discs, you need to select an
audio output format from a menu.
—
If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer.
—
Make sure that none of the connecting cables are
bent, twisted, or damaged.
—
Not all listening modes use all speakers.
41
Specify the speaker distances and adjust the
individual speaker levels.
65
Make sure that the speaker setup microphone is not
still connected.
—
Appendix
If the input signal format is set to “PCM” or “DTS”. 77
Set it to “Off”.
Make sure the speakers are configured correctly.
64
■ The front high, front wide and surround back
speakers produce no sound
■ Only the front speakers produce sound
When the Stereo or Mono listening mode is selected, 45
only the front speakers and subwoofer produce
sound.
41
In the Mono listening mode, only the front speakers
output sound if the “Output Speaker” setting is set
to “Left / Right”.
68
Depending on the current listening mode, no sound
may be produced by the front high, front wide and
surround back speakers. Select another listening
mode.
Check the Speaker Configuration.
64
Depending on the sources, the sound produced by the —
front high, front wide and surround back speakers
may be weak.
Make sure the speakers are configured correctly.
■ Only the center speaker produces sound
If you use the Dolby Pro Logic IIx Movie, Dolby Pro —
Logic IIx Music, or Dolby Pro Logic IIx Game
listening mode with a mono source, such as an AM
radio station or mono TV program, the sound is
concentrated in the center speaker.
In the Mono listening mode, only the center speaker
output sound if the “Output Speaker” setting is set
to “Center”.
68
Make sure the speakers are configured correctly.
64
When Powered Zone 3 is used, playback in the main —
room is reduced to 5.2 channels and the front high,
front wide and surround back speakers produce no
sound.
■ The subwoofer produces no sound
■ The surround speakers produce no sound
When the T-D (Theater-Dimensional), Stereo or
Mono listening mode is selected, the surround
speakers produce no sound.
64
When Powered Zone 2 is used, playback in the main —
room is reduced to 7.2 channels and the front wide
speakers produce no sound.
—
When you play source material that contains no
information in the LFE channel, the subwoofer
produces no sound.
—
Make sure the speakers are configured correctly.
64
■ There’s no sound with a certain signal format
Depending on the source and current listening mode, 41
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Check the digital audio output setting on the
connected device. On some game consoles, such as
those that support DVD, the default setting is off.
—
64
With some DVD-Video discs, you need to select an
audio output format from a menu.
—
Make sure the speakers are configured correctly.
When Powered Zone 4 is used, playback in the main —
room is reduced to 3.2 channels and the surround
speakers produce no sound.
Depending on the input signal, some listening modes 41-48
cannot be selected.
■ The center speaker produces no sound
When the Stereo or Mono listening mode is selected, —
the center speaker produces no sound.
In the Mono listening mode, only the front speakers
output sound if the “Output Speaker” setting is set
to “Left / Right”.
68
En-99
■ Can’t get 6.2/7.2 playback
If no surround back speakers, front wide and front
—
high speakers are connected, or the Zone 3/4 speakers
are being used, 6.2/7.2 playback is not possible.
Depending on the number of connected speakers, it is 41-48
not always possible to select all of the listening
modes.
■ The speaker volume cannot be set as required
Check to see if a maximum volume has been set.
78
If the volume level of each individual speaker has
38, 65
been adjusted to high positive values, then the
maximum master volume possible may be reduced.
Note that the individual speaker volume levels are set
automatically after the Audyssey MultEQ® XT32
Room Correction and Speaker Setup has been
performed.
■ Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and the like may degrade the
audio performance, so refrain from doing it.
—
An audio cable may be picking up interference. Try
repositioning your cables.
—
■ The Late Night function doesn’t work
Make sure the source material is Dolby Digital,
Dolby Digital Plus, and Dolby TrueHD.
55
Make sure that the “TrueHD Loudness
Management” setting is not set to “Off”. The Late
Night function doesn’t work when this setting is
disabled.
69
Appendix
■ About DTS signals
With some CD and LD players, you won’t be able to —
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesn’t recognize it as a genuine DTS signal. In such
cases, you may hear noise.
Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a
malfunction.
—
■ The beginning of audio received by an HDMI IN
can’t be heard
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio
signals, audio output may not start immediately.
—
■ There’s no sound during Whole House Mode
Make sure you’ve selected an analog audio input.
When the resolution is set to any resolution not
supported by the TV, no video is output from the
HDMI output.
Video
When DTS program material ends and the DTS
—
bitstream stops, the AV receiver remains in DTS
listening mode and the dts indicator remains on. This
is to prevent noise when you use the pause, fast
forward, or fast reverse function on your player. If
you switch your player from DTS to PCM, you may
not hear any sound because the AV receiver does not
switch formats immediately. In such case, you should
stop your player for about three seconds and then
resume playback.
—
(North American models) When using the Whole
51
House Mode with “Tuner” input selector, connect
antennas to both the MAIN and ZONE 2 ANTENNA
jacks/terminals.
■ There’s no picture
Make sure that all video connecting plugs are pushed 16
in all the way.
Make sure that each video component is properly
connected.
17, 18
If your TV is connected to the HDMI output, set the
“Monitor Out” setting other than “Analog”, and
select “- - - - -” in the “HDMI Input” setting to
watch composite video, and component video
sources.
59,60
On your TV, make sure that the video input to which —
the AV receiver is connected is selected.
If the video source is connected to a component video 18, 61
input, you must assign that input to an input selector,
and your TV must be connected to either the HDMI
output or COMPONENT VIDEO MONITOR OUT.
If the video source is connected to a composite video 18
input, you must assign that input to an input selector,
and your TV must be connected to the HDMI output
or the corresponding composite video output.
17, 60
On your TV, make sure that the video input to which —
the AV receiver is connected is selected.
When the “Monitor Out” setting is set to “Both”, the 59, 80
“HDMI Through” setting is only available for the
HDMI OUT MAIN jack.
■ There’s no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed.
114
When the “Monitor Out” setting is set to “Analog”, 59,
no video is output by the HDMI output.
109
En-100
If the message “Resolution Error” appears on the
—
AV receiver’s display, this indicates that your TV
does not support the current video resolution and you
need to select another resolution on your DVD
player.
■ The on-screen menus don’t appear
If your TV is connected to the COMPONENT
59, 61
VIDEO MONITOR OUT or MONITOR OUT V, set
the “Monitor Out” setting to “Analog”, select
“- - - - -” in “Component Video Input”, and assign a
composite video input for that input selector in order
to watch composite video sources.
If the video source is connected to an HDMI input,
you must assign that input to an input selector, and
your TV must be connected to the HDMI output.
59
When the AV receiver is not connected to a TV via
HDMI OUT MAIN, on-screen menus are not
displayed.
—
■ The on-screen information does not appear
Depending on the input signal, the on-screen
53
information may not appear when the input signal
from HDMI IN is output to a device connected to the
HDMI output.
Tuner
■ Reception is noisy, FM stereo reception is noisy,
or the FM STEREO indicator doesn’t light
Relocate your antenna.
—
Move the AV receiver away from your TV or
computer.
—
Listen to the station in mono.
33
When listening to an AM station, operating the
remote controller may cause noise.
—
Passing cars and airplanes can cause interference.
—
Concrete walls weaken radio signals.
—
If nothing improves the reception, install an outdoor
antenna.
—
Appendix
If you cannot operate it, you will need to enter the
appropriate remote control code.
Remote Controller
■ The remote controller doesn’t work
Before operating this unit, be sure to press Receiver. —
Make sure that the batteries are installed with the
correct polarity.
4
Install new batteries. Don’t mix different types of
batteries, or old and new batteries.
4
Make sure that the remote controller is not too far
4
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor.
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
—
If the AV receiver is installed in a rack or cabinet
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
—
Make sure you’ve selected the correct remote
controller mode.
10, 93
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
—
Make sure you’ve entered the correct remote control 92
code.
Make sure to set the same ID on both the AV receiver 83
and remote controller.
91
To control another manufacturer’s component, point 92
the remote controller at that component.
To control an Integra/Onkyo component that’s
93
connected via u, point the remote controller at the
AV receiver. Be sure to enter the appropriate remote
control code first.
To control an Integra/Onkyo component that’s not
connected via u, point the remote controller at the
component. Be sure to enter the appropriate remote
control code first.
93
The entered remote control code may not be correct.
If more than one code is listed, try each one.
—
■ Can’t learn commands from another remote
controller
When learning commands, make sure that the
transmitting ends of both remote controllers are
pointing at each other.
96
Are you trying to learn from a remote controller that —
cannot be used for learning? Some commands
cannot be learned, especially those that contain
several instructions.
If it’s an Integra/Onkyo component, make sure that
the u cable and analog audio cable are connected
properly. Connecting only an u cable won’t be
enough.
21
Make sure you’ve selected the correct remote
controller mode.
10, 93
Make sure your iPod/iPhone is actually playing.
—
Make sure your iPod/iPhone is properly inserted in
the Dock.
—
Make sure the AV receiver is turned on, the correct —
input source is selected, and the volume is turned up.
If you’ve connected an cassette tape deck to the
50
TV/CD IN jack, or an RI Dock to the TV/CD IN or
GAME 1 IN jacks, for the remote controller to work
properly, you must set the input display
appropriately.
Make sure the plugs are pushed in all the way.
—
Try resetting your iPod/iPhone.
—
■ There’s no video
Make sure that your iPod/iPhone model’s TV OUT
setting is set to On.
En-101
Some versions of the iPod/iPhone do not output
video.
—
■ The AV receiver’s remote controller doesn’t
control my iPod/iPhone
Make sure your iPod/iPhone is properly inserted in
—
the Dock. If your iPod/iPhone is in a case, it may not
connect properly to the Dock. Always remove your
iPod/iPhone from the case before inserting it into the
Dock.
The iPod/iPhone cannot be operated while it’s
displaying the Apple logo.
—
Make sure you’ve selected the right remote mode.
90
When you use the AV receiver’s remote controller,
point it toward your AV receiver.
—
If you still can’t control your iPod/iPhone, start
—
playback by pressing your iPod/iPhone model’s Play
button. Remote operation should then be possible.
Try resetting your iPod/iPhone.
—
Depending on your iPod/iPhone, some buttons may
not work as expected.
—
■ The AV receiver unexpectedly selects my
iPod/iPhone as the input source
RI Dock for iPod/iPhone
■ There’s no sound
■ Can’t control other components
Make sure the correct input is selected on your TV or —
the AV receiver.
—
Always pause iPod/iPhone playback before selecting —
a different input source. If playback is not paused, the
Direct Change function may select your iPod/iPhone
as the input source by mistake during the transition
between tracks.
■ iPod/iPhone doesn’t work properly
Try reconnecting your iPod/iPhone.
—
Appendix
Zone 2/3/4
■ There’s no sound
Only components connected to analog or HDMI (2ch —
PCM) inputs can be played in Zone 2.
Only components connected to analog inputs can be
played in Zone 3/4.
If the server is serving large music files to several
—
networked devices simultaneously, the network may
become overloaded and playback may be interrupted.
Reduce the number of playback devices on the
network, upgrade your network, or use a switch
instead of a hub.
—
■ The Zone 2/3/4 speakers produce no sound
See “Multi Zone” for the conditions in which
Powered Zone 2/3/4 cannot be used.
84
To use the Zone 2 speakers, you must set the
“Powered Zone 2” setting to “Yes”.
63
To use the Zone 3 speakers, you must set the
“Powered Zone 3” setting to “Yes”.
63
To use the Zone 4 speakers, you must set the
“Powered Zone 4” setting to “Yes”.
63
■ Can’t connect to the AV receiver from a Web
browser
If you’re using DHCP, your router may not always
82
allocate the same IP address to the AV receiver, so if
you find that you can’t connect to a server or Internet
radio station, recheck the AV receiver’s IP address on
the “Network” screen.
Check the “Network” settings.
82
USB Device Playback
■ Can’t access the music files on a USB device
Music Server and Internet Radio
Make sure the USB device is plugged in properly.
■ Can’t access the server or Internet radio
Certain network service or contents available through —
this device may not be accessible in case the service
provider terminates its service.
Check the network connection between the AV
receiver and your router or switch.
115
Make sure that your modem and router are properly
connected, and make sure they are both turned on.
—
Make sure the server is up and running and
compatible with the AV receiver.
115
Check the “Network”settings.
82
USB memory devices with security functions cannot —
be played.
Others
■ Playback stops while listening to music files on
the server
Make sure your server is compatible with the AV
receiver.
—
The AV receiver supports USB devices that support 116
the USB mass storage device class. However,
playback may not be possible with some USB devices
even if they conform to the USB mass storage device
class.
115
If you download or copy large files on your
—
computer, playback may be interrupted. Try closing
any unused programs, use a more powerful computer,
or use a dedicated server.
■ Standby power consumption
80, 82
In the following cases, the power consumption in
standby mode may reach up to a maximum of
12.5 W:
– The “HDMI Control(RIHD)” setting is set to
“On”. (Depending on the TV status, the AV
receiver will enter standby mode as usual.)
– The “HDMI Through” setting is set to other than
“Off”.
– The “Network Standby” setting is set to “On”.
En-102
If an MHL-enabled mobile device is connected to the 17
AUX (front) input, the power consumption in standby
mode will increase.
■ The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening —
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct.
■ The speaker distance cannot be set as required
The values entered may be automatically adjusted
with values best-suited for your home theater.
—
■ How do I change the language of a multiplex
source
Use the “Multiplex” setting in the “Audio Adjust”
menu to select “Main” or “Sub”.
68
■ The u functions don’t work
To use u, you must make an u connection and an 21
analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
While Zone 2/3/4 is selected, the u functions don’t 21
work.
■ The functions System Off/Auto Power On and
Direct Change don’t work for components
connected via u
These functions don’t work when Zone 2/3/4 is
turned on.
21
■ When performing Automatic Speaker Setup, the
measurement fails and the message “Ambient
noise is too high.” is displayed.
This can be caused by a malfunction in your speaker —
unit. Check if the unit produces normal sounds.
Appendix
■ The following setting can be made for
composite video inputs
• Video Attenuation
If you have a game console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT :Off: The gain is not changed (default).
Video ATT :On: The gain is reduced by the values
specified below.
– 2 dB for the ZONE 2 OUT V and HDMI output.
– 6 dB for the MONITOR OUT V output.
To make this setting, you must use the buttons on the
AV receiver.
Press the input selector button for the source that you
want to set, simultaneously with Setup. Note that the
input selector must be assigned to a composite video
input. While holding down the input selector button,
press Setup until “Video ATT :On” appears on the AV
receiver’s display. Then, release both buttons. To turn
the setting off, repeat the above process so that “Video
ATT :Off” appears on the AV receiver’s display, and
release the buttons.
Note
• With the USB input selector, this setting is only available when
an iPod/iPhone is connected and set to Extended Mode (Video)
or Standard Mode.
■ If the picture on your TV/monitor connected to
the HDMI output is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
press the STB/DVR and 8On/Standby buttons on the
AV receiver. While holding down STB/DVR, press
8On/Standby until “Deep Color:Off” appears on the
AV receiver’s display. Then, release both buttons. To
reactivate the DeepColor function, repeat the above
process until “Deep Color:On” appears on the AV
receiver’s display and release the buttons.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make
sure that the material will be recorded correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.
Important Note Regarding Video Playback
The AV receiver can upconvert component video and
composite video sources for display on a TV connected to
the HDMI output. However, if the picture quality of the
source is poor, upconversion may make the picture worse
or disappear altogether.
In this case, try the following:
1
If the video source is connected to a component
video input, connect your TV to COMPONENT
VIDEO MONITOR OUT.
If the video source is connected to a composite video
input, connect your TV to MONITOR OUT V.
2
On the main menu, select “Input/Output Assign”,
and then “Component Video Input” (➔ page 61).
If the video source is connected to COMPONENT
VIDEO IN 1, select the relevant input selector, and
assign it to “IN1”.
If the video source is connected to COMPONENT
VIDEO IN 2, select the relevant input selector, and
assign it to “IN2”.
If the video source is connected to a composite video
input, select the relevant input selector, and assign it to
“- - - - -”.
Tip
• To by-pass the upconversion, set the “Picture Mode” setting to
“Direct” (➔ page 74).
En-103
Appendix
Firmware Update
To update the firmware of the AV receiver, you can choose
from the following two methods: update via network, or
update via USB storage. Choose the one that best suits
your environment. Before proceeding with the update,
please read the corresponding explanations carefully.
■ Update via network
You need a wired Internet connection to update the
firmware.
■ Update via USB storage (➔ page 106)
Please prepare a USB storage device such as a USB flash
memory stick. You need at least 32 MB of available
space to update the firmware.
Limitation of liability
The program and accompanying online documentation
are furnished to you for use at your own risk. Onkyo will
not be liable and you will have no remedy for damages
for any claim of any kind whatsoever concerning your
use of the program or the accompanying online
documentation, regardless of legal theory, and whether
arising in tort or contract. In no event will Onkyo be
liable to you or any third party for any special, indirect,
incidental, or consequential damages of any kind,
including, but not limited to, compensation,
reimbursement or damages on account of the loss of
present or prospective profits, loss of data, or for any
other reason whatsoever.
See the Integra web site for latest information.
Note
• Check the network connection before updating.
• Do not touch any cable or device connected to the AV receiver
during the update process.
• Do not attempt to access the AV receiver from your PC while it
is being updated.
• Do not shutdown the power of the AV receiver while it is being
updated.
• The storage media in the USB card reader may not work.
• If the USB device is partitioned, each section will be treated as an
independent device.
• If the USB device contains a lot of data, the AV receiver may take
a while to read it.
• Operation is not guaranteed for all USB devices, which includes
the ability to power them.
• Onkyo takes no responsibility whatsoever for the loss or damage
of data resulting from the use of a USB device with the AV
receiver. Onkyo recommends that you back up your important
music files beforehand.
• If you connect a USB hard disk drive to the USB port, Onkyo
recommends that you use its AC adapter to power it.
• USB hubs and USB devices with hub functions are not supported.
Do not connect your USB device via a USB hub.
• USB devices with security functions are not supported.
Updating the Firmware via Network
The AV receiver allows you to update the firmware using
network connection on the rear panel.
Note
• Make sure your AV receiver and TV are turned on and an
Ethernet cable is connected to the rear panel of the AV receiver.
• Never unplug or turn off the AV receiver while it is being
updated.
• Never plug or unplug an HDMI or Ethernet cable during the
update process.
• Do not attempt to access the AV receiver from your PC while it
is being updated.
• Never unplug the power cord during the update process.
• It takes up to 60 minutes to complete the firmware update.
• The AV receiver will retain all your settings after the update is
finished.
Before Starting
• Set the “HDMI Control(RIHD)” setting to “Off”
(➔ page 80).
• Turn off the controller device connected via RS232 and
network.
• Turn off Multi Zone if this function is present.
• Stop playback of contents from Internet Radio,
iPod/iPhone, USB or servers, etc.
En-104
Appendix
Update Procedure
1
Press Receiver followed by Home on the remote
controller.
The Home menu appears on the TV screen.
2
Select “Firmware Update” and press Enter.
Note that the “Firmware Update” option will be
grayed out for a short while after the AV receiver is
turned on. Please wait until it becomes operable.
3
Select “Update via NET” and press Enter.
Note that this option will not be available if there is no
firmware file newer than the currently installed
version.
4
Select “Update” and press Enter.
The update process will begin.
During the update process, the on-screen display may
disappear depending on the updated program. When
this occurs, you can still view the update progress on
the AV receiver’s display. The on-screen display will
reappear after the update is complete, and upon
turning the AV receiver off and on again.
5
The message “Completed!” appears on the AV
receiver’s display, indicating that the update has
been completed.
6
Turn off the AV receiver using 8On/Standby on
the front panel.
Do not use 8Receiver on the remote controller.
Once turned off, the AV receiver will automatically
turn on again.
Congratulations! You now have the latest firmware
installed on your Integra AV receiver.
Troubleshooting
Case 1:
If an error occurs, “Error!! *-**” is displayed on the AV
receiver’s display. (Alpha-numeric characters on the front
display are denoted by asterisks.) Refer to the following
table and take appropriate action.
■ Errors during an update via network
Error Code
Description
*-10, *-20
The Ethernet cable was not detected.
Reconnect the cable properly.
*-11, *-13, *-21,
Internet connection error.
Check the following items:
• Make sure the IP address, subnet mask,
gateway address, and DNS server are
configured properly.
• Make sure the router is turned on.
• Make sure the AV receiver and the router are
connected with an Ethernet cable.
• Make sure your router is configured properly.
See the instruction manual of the router.
• If your network allows only one client
connection and there is any other device
already connected, the AV receiver will not be
able to access the network. Consult your
Internet Service Provider (ISP).
• If your modem does not function as a router,
you will need a router. Depending on your
network, you may need to configure the proxy
server if necessary. See the document
provided by your ISP. If you are still unable to
access the Internet, the DNS or proxy server
may be temporarily down. Contact your ISP.
*-28
Others
Retry the update procedure from the beginning.
If the error persists, please contact Integra
Support (➔ page 107) and provide the error
code.
Case 2:
If an error occurs during the update process, disconnect
then reconnect the AC power cord and try again.
En-105
Case 3:
If you do not have an Internet connection to the network,
please contact Integra Support (➔ page 107).
Appendix
Updating the Firmware via USB
The AV receiver allows you to update the firmware using a
USB device.
Note
• Never unplug or turn off the AV receiver during the update
process.
• Never plug or unplug an HDMI cable or a USB device during the
update process.
• Never unplug the USB storage device containing the firmware
file or the AC power cord during the update process.
• Do not attempt to access the AV receiver from your PC while it
is being updated.
• It takes up to 60 minutes to complete the firmware update.
• The AV receiver will retain all your settings after the update is
finished.
Before Starting
• Set the “HDMI Control(RIHD)” setting to “Off”
(➔ page 80).
• Turn off the controller device connected via RS232 and
network.
• Turn off Multi Zone if this function is present.
• Stop playback of contents from Internet Radio,
iPod/iPhone, USB or servers, etc.
• If there is any data in the USB device, remove it first.
Update Procedure
1
Connect a USB device to your PC. If there is any
data in the USB device, remove it first.
2
Download the firmware file from the Integra web
site. The file name is as follows:
ONKAVR****_************.zip
Unzip the downloaded file. The following six files
are created:
ONKAVR****_************.of1
ONKAVR****_************.of2
ONKAVR****_************.of3
ONKAVR****_************.of4
ONKAVR****_************.of5
ONKAVR****_************.of6
3
Copy the extracted files to the USB device. Be
careful not to copy the zip file.
4
Remove the USB device from your PC and connect
it to the USB port on the AV receiver.
When the AV receiver has two USB ports, you can
use either one.
5
Make sure the AV receiver and TV are turned on.
If the AV receiver is in standby mode, press
8On/Standby on the AV receiver to light up the
front display.
6
Select the USB input source.
“Now Initializing...” appears on the AV receiver’s
display and then the name of the USB device is
displayed. It takes 20 to 30 seconds to recognize the
USB device.
7
Press Receiver followed by Home on the remote
controller.
The Home menu appears on the TV screen.
8
Select “Firmware Update” and press Enter.
En-106
9
Select “Update via USB” and press Enter.
Note that this option will not be available if there is no
firmware file newer than the currently installed
version.
10
Select “Update” and press Enter.
The update process will begin.
During the update process, the on-screen display may
disappear depending on the updated program. When
this occurs, you can still view the update progress on
the AV receiver’s display. The on-screen display will
reappear after the update is complete, and upon
turning the AV receiver off and on again.
Do not turn off the AV receiver and do not remove the
USB device during the update process.
11
The message “Completed!” appears on the AV
receiver’s display, indicating that the update has
been completed.
Remove the USB device.
12
Turn off the AV receiver using 8On/Standby on
the front panel.
Do not use 8Receiver on the remote controller.
Once turned off, the AV receiver will automatically
turn on again.
Congratulations! You now have the latest firmware
installed on your Integra AV receiver.
Appendix
Troubleshooting
Case 1:
If an error occurs, “Error!! *-**” is displayed on the AV
receiver’s display. (Alpha-numeric characters on the front
display are denoted by asterisks.) Refer to the following
table and take appropriate action.
■ Errors during an update via USB
The Americas
Integra Division of
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-225-1946, 201-818-9200
Fax: 201-785-2650
Hours: M-F 9am-8pm/Sat-Sun 10am-8pm ET
http://www.integrahometheater.com
Error Code
Description
Europe
Integra Division of
*-10, *-20
The USB device was not detected. Make sure
the USB flash memory or USB cable is
properly connected to the USB port. If the USB
storage device has its own power supply, use it
to power the USB device.
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
http://www.integra.eu
*-14
Others
The firmware file was not found in the root
folder of the USB device, or the firmware file is
for another model. Retry and download the file
on the support page of the web site, following
the on-site instructions. If the error persists,
please contact Integra Support and provide the
error code.
Retry the update procedure from the beginning.
If the error persists, please contact Integra
Support and provide the error code.
Case 2:
If an error occurs during the update process, disconnect
then reconnect the AC power cord and try again.
China
Integra Division of
1301, 555 Tower, No.555 West NanJin Road, Jin an,
Shanghai, China 200041
Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.integra.com.cn
Asia, Oceania, Middle East, Africa
Please contact an Integra distributor referring to
Integra Worldwide web site.
http://www.integraworldwide.com
Integra Division of
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
http://www.integraworldwide.com
The above-mentioned information is subject to change
without prior notice. Visit the Integra web site for the latest
update.
En-107
Appendix
Connection Tips and
Video Signal Path
The AV receiver supports several connection formats for
compatibility with a wide range of AV equipment. The
format you choose will depend on the formats supported by
your components. Use the following sections as a guide.
The on-screen setup menus appear only on a TV that
is connected to HDMI OUT MAIN. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
■ “Monitor Out” set to “HDMI Main” or “HDMI
Sub”
Video input signals flow through the AV receiver as
shown, with composite video, PC IN (Analog RGB), and
component video sources all being upconverted for the
HDMI output. Use these settings if you connect either
HDMI OUT MAIN or HDMI OUT SUB of the AV
receiver to your TV.
The composite video and component video outputs pass
through their respective input signals as they are.
When you connect a video component to an HDMI,
COMPONENT or COMPOSITE input, you must assign
that input to an input selector (➔ pages 60, 61, 62).
Video Signal Flow Chart
Video Connection Formats
Video components can be connected by using any one of
the following video connection formats: composite video,
PC IN (Analog RGB), component video, or HDMI, the
latter offering the best picture quality.
The AV receiver can upconvert between video formats,
depending on the “Monitor Out” setting (➔ page 59),
which generally determines whether video signals are
upconverted for the component video output or the HDMI
output.
Tip
• For optimal video performance, THX recommends that video
signals pass through the system without upconversion (e.g.,
component video input passing through to component video
output).
• To by-pass the upconversion, set the “Picture Mode” setting to
“Direct” (➔ page 74).
■ “Monitor Out” set to “Both”
Video input signals flow through the AV receiver as
shown, with composite video, PC IN (Analog RGB), and
component video sources all being upconverted for both
HDMI outputs. Use this setting if you connect both
HDMI OUT MAIN and HDMI OUT SUB of the AV
receiver to your TV.
Note that video signals are output from both HDMI outputs
at the resolution supported by both TVs.
The composite video and component video outputs pass
through their respective input signals as they are.
When you connect a video component to an HDMI,
COMPONENT or COMPOSITE input, you must assign
that input to an input selector (➔ pages 60, 61, 62).
Video Signal Flow Chart
Blu-ray Disc/DVD player, etc.
Blu-ray Disc/DVD player, etc.
Composite
PC IN
(Analog RGB)
Component
HDMI
Composite
IN
PC IN
(Analog RGB)
Component
HDMI
IN
AV receiver
AV receiver
MONITOR OUT
Composite
Component
HDMI
MONITOR OUT
Composite
Component
HDMI
TV, projector, etc.
TV, projector, etc.
Note
• When “Monitor Out” is set to “Both”, the “Resolution” setting
cannot be selected (➔ page 59).
• The “HDMI Through” setting is only available for the HDMI
OUT MAIN jack (➔ page 80).
En-108
Appendix
■ “Monitor Out” set to “Analog”
Video input signals flow through the AV receiver as
shown, with composite video and PC IN (Analog RGB)
sources being upconverted for the component video output.
Use this setting if you connect the AV receiver’s
COMPONENT VIDEO MONITOR OUT to your TV.
The composite video and component video outputs pass
through their respective input signals as they are.
This signal flow also applies when the “Resolution”
setting is set to “Through” (➔ page 59).
Composite
Video Signal Flow and the Resolution Setting
When the “Monitor Out” setting is set to “Analog”
(➔ page 59), if the “Resolution” setting is set to anything
other than “Through” (➔ page 59), the video signal flow
will be as shown here, with composite video and PC IN
(Analog RGB) sources being upconverted for the
component video output.
The composite video and component video outputs pass
through their respective analog input signals as they are.
HDMI input signals are not output.
Video Signal Flow Chart
Video Signal Flow Chart
Blu-ray Disc/DVD player, etc.
Blu-ray Disc/DVD player, etc.
Component
PC IN
(Analog RGB)
HDMI
Composite
Component
PC IN
(Analog RGB)
HDMI
■ Signal Selection
If signals are present at more than one input, the inputs will
be selected automatically in the following order of priority:
HDMI, component video, composite video.
However, for component video only, regardless of whether
a component video signal is actually present, if a
component video input is assigned to the input selector,
that component video input will be selected. And if no
component video input is assigned to the input selector,
this will be interpreted as no component video signal being
present.
In the Signal Selection Example shown below, video
signals are present at both the HDMI and composite video
inputs. However, the HDMI signal is automatically
selected as the source and the video is output by the HDMI
output.
IN
IN
Signal Selection Example
Blu-ray Disc/DVD player, etc.
AV receiver
AV receiver
MONITOR OUT
MONITOR OUT
Composite
Component
*1
HDMI
TV, projector, etc
*1
Composite
Component
Composite
HDMI
Component
HDMI
IN
AV receiver
TV, projector, etc
For details, refer to “Video Resolution Chart”
(➔ page 111).
MONITOR OUT
Composite
Component
TV, projector, etc.
En-109
HDMI
Appendix
Audio Connection Formats
Audio components can be connected by using any of the
following audio connection formats: analog, optical,
coaxial, or HDMI.
When choosing a connection format, bear in mind that the
AV receiver does not convert digital input signals for
analog line outputs and vice versa.
If signals are present at more than one input, the inputs will
be selected automatically in the following order of priority:
HDMI, digital, analog.
Audio Signal Flow Chart
Blu-ray Disc/DVD player, etc.
Analog
Optical
Coaxial
HDMI
IN
AV receiver
*1
*1
*1
OUT
HDMI
*1
*2
TV, projector, etc.
*1
*2
Depends on the “Audio TV Out” setting (➔ page 81).
This is possible when “Audio Return Channel” is set to
“Auto” (➔ page 81), the TV/CD input selector is selected,
and your TV is ARC capable.
Tip
• When a signal is input via HDMI and the corresponding input
selector is selected, the HDMI indicator lights. In the case of an
optical or coaxial connection, the DIGITAL indicator lights. If
the analog audio is output, or if neither HDMI nor digital signal
inputs are assigned, ANALOG indicator lights.
En-110
Appendix
Video Resolution Chart
The following tables show how video signals at different resolutions are output by the AV receiver.
NTSC/PAL
✔: Output available
Output
s
HDMI
4K*2
1080p/24
1080p/24
✔
✔*4
1080p
✔
✔
✔*4
1080i
✔
✔
720p
✔
480p/576p
Input
HDMI
Component
Composite
*1
*2
*3
*4
*5
*6
*7
480p/576p
480i/576i
Component
1080p
1080i
1080i
720p
✔
✔*4
✔
✔
✔
✔
✔*4
✔
✔
✔
✔
✔
✔*4
480i/576i
✔
✔
✔
✔
✔
✔
1080p
✔
✔
✔*4*5
1080i
✔
✔
✔*5
✔*4*5
✔
✔
720p
✔
✔
✔*5
✔*5
✔*4*5
✔
✔
480p/576p
✔
✔
✔*5
✔*5
✔*5
✔*4*5
✔*6
✔*6
✔
480i/576i
✔
✔
✔*5
✔*5
✔*5
✔*4*5
✔*5
✔*6
✔*6
✔
✔
480i/576i
✔
✔
✔*5
✔*5
✔*5
✔*4*5
✔*5
✔*6
✔*6
✔
✔
✔
✔
✔*5
✔*5
✔*5
✔*5
✔*7
✔*7
✔*7
PC IN (Analog RGB)*1*3
1080p
720p
480p/576p
480i/576i
Composite
480i/576i
✔*4
✔
✔
Available resolutions: [640 × 480 60 Hz], [800 × 600 60 Hz], [1024 × 768 60 Hz], [1280 × 1024 60 Hz]
Supported resolutions: [3840 × 2160 24/25/30 Hz], [4096 × 2160 24 Hz]
When video signals of personal computers connected to PC IN are output from HDMI OUT SUB, they may not display properly on some TVs.
Supported resolutions for HDMI OUT SUB (“Monitor Out” = “Sub”).
Supported resolutions for HDMI OUT SUB (“Monitor Out” = “Both”).
The output is limited to 480p/576p for an effective signal in the effect of copy protect.
PC IN (Analog RGB) input signal is output at 720p resolution when you select “Analog” in the “Monitor Out” setting (➔ page 59) and “Through” in the “Resolution” setting (➔ page 59).
En-111
Appendix
Using an RIHDcompatible TV, Player,
or Recorder
p, which stands for Remote Interactive over
HDMI, is the name of the system control function found on
Integra/Onkyo components. The AV receiver can be used
with CEC (Consumer Electronics Control), which allows
system control over HDMI and is part of the HDMI
standard. CEC provides interoperability between various
components, however, operation with components other
than p-compatible components cannot be
guaranteed.
Operations that can be performed with
p connection
About p-Compatible Components
The following components are p-compatible (As
of January 2012).
■ TV
• Toshiba TV
• Sharp TV
■ Players/Recorders
• Onkyo and Integra p-compatible players
• Toshiba players and recorders
• Sharp players and recorders (only when used together
with Sharp TV)
*
Models other than those mentioned above may have some
interoperability if compatible with CEC, which is part of the
HDMI Standard, but operation cannot be guaranteed.
Note
• For proper linked operations, do not connect more pcompatible components than the quantities specified below, to
the HDMI input terminal.
– Blu-ray Disc/DVD players: up to three.
– Blu-ray Disc/DVD recorders/Digital Video Recorders: up to
three.
– Cable/Satellite Set-top boxes: up to four.
• Do not connect the AV receiver to another AV receiver/AV
amplifier via HDMI.
• Proper linked operations are not guaranteed when more
p-compatible components than the above-mentioned
quantities are connected.
■ For p-compatible TV
The following linked operations are enabled by connecting
the AV receiver to an p-compatible TV.
• The AV receiver will enter standby mode when the TV is
set to standby.
• You can set on the menu screen of the TV to either output
the audio from the speakers connected to the AV
receiver, or from the speakers of the TV.
• It is possible to output the audio coming from the tuner or
auxiliary input of your TV to the speakers of the AV
receiver. (A connection such as an optical digital cable or
similar is required in addition to the HDMI cable.)
• Input to the AV receiver can be selected with the remote
controller of the TV.
• Operations such as volume adjustment or similar for the
AV receiver can be performed from the remote controller
of the TV.
■ For p-compatible players/recorders
The following linked operations are enabled by connecting
the AV receiver to an p-compatible
player/recorder.
• When playback is started on the player/recorder, AV
receiver will switch to the HDMI input of the
player/recorder that is playing back.
• Operation of the player/recorder is possible using the
remote controller supplied with the AV receiver.
*
Depending on the model used, not all operations may be
available.
To be continued
En-112
Appendix
■ How to connect and setup
1
2
Confirm the connection and settings.
1. Connect the HDMI OUT MAIN jack to the HDMI
input jack of the TV.
Blu-ray Disc/DVD player, etc.
HDMI
connection
AV receiver
DIGITAL AUDIO
connection
(OPTICAL)
HDMI
connection
TV, projector, etc.
2. Connect the audio output from the TV to the
OPTICAL IN 2 jack of the AV receiver using an
optical digital cable.
Note
• When the audio return channel (ARC) function is used with
an ARC capable TV, this connection is not necessary
(➔ page 81).
3. Connect the HDMI output of the Blu-ray
Disc/DVD player/recorder to the HDMI IN 1 jack
of the AV receiver.
Note
• It is necessary to assign the HDMI input when connecting
the Blu-ray Disc/DVD player/recorder to other jacks
(➔ page 60). Do not assign an HDMI IN to the TV/CD
selector at this time, otherwise appropriate CEC (Consumer
Electronics Control) operation will not be guaranteed.
3
Change each item in the “HDMI” menu according
to the following settings:
• HDMI Control(RIHD): On
• Audio Return Channel (ARC): Auto
See details of each setting (➔ pages 80, 81).
Confirm the settings.
1. Turn on the power for all connected components.
2. Turn off the power of the TV, and confirm that the
power of the connected components is turned off
automatically with the link operation.
3. Turn on the power of the Blu-ray Disc/DVD
player/recorder.
4. Start playback on the Blu-ray Disc/DVD
player/recorder, and verify the following:
• The AV receiver automatically turns on, and
selects the input to which the Blu-ray
Disc/DVD player/recorder is connected.
• The TV automatically turns on, and selects the
input to which the AV receiver is connected.
5. Following the operating instructions of the TV,
select “Use the TV speakers” from the menu
screen of the TV, and confirm that the audio is
output from the speakers of the TV, and not from
the speakers connected to the AV receiver.
6. Select “Use the speakers connected from the AV
receiver” from the menu screen of the TV, and
confirm that the audio is output from the speakers
connected to the AV receiver, and not from the
TV speakers.
Note
• Perform the above operations when you use the AV receiver
for the first time, when the settings of each component are
changed, when the main power of each component is turned
off, when the power cable is disconnected from the power
supply, or when there has been a power outage.
En-113
4
Operate with the remote controller.
For buttons that can be operated (➔ page 94).
Note
• Audio from DVD-Audio or Super Audio CD may not output
from the TV speakers. You will be able to output the audio
from the TV speakers by setting the audio output of the
DVD player to 2ch PCM. (It may not be possible depending
on the player models.)
• Even if you set to output audio on the TV speakers, audio
will be output from the speakers connected to the AV
receiver when you adjust the volume or switch the input on
the AV receiver. To output audio from the TV speakers, redo the corresponding operations on the TV.
• In case of an p connection with u and u audio
control compatible components, do not connect the u
cable at the same time.
• On the TV, when you select anything other than the HDMI
jack to which the AV receiver is connected, the input on the
AV receiver will be switched to “TV/CD”.
• The AV receiver will automatically power on in conjunction
when it determines it to be necessary. Even if the AV
receiver is connected to an p compatible TV or
player/recorder, it will not power on if it is not necessary. It
may not power on in conjunction when the TV is set to
output audio from the TV.
• Linked functions with the AV receiver may not work
depending on the component model connected. In such
cases, operate the AV receiver directly.
Appendix
About HDMI
Designed to meet the increased demands of digital TV,
HDMI (High Definition Multimedia Interface) is a new
digital interface standard for connecting TVs, projectors,
Blu-ray Disc/DVD players, set-top boxes, and other video
components. Until now, several separate video and audio
cables have been required to connect AV components.
With HDMI, a single cable can carry control signals,
digital video, and up to eight channels of digital audio (2channel PCM, multichannel digital audio, and
multichannel PCM).
The HDMI video stream (i.e., video signal) is compatible
with DVI (Digital Visual Interface)*1, so TVs and displays
with a DVI input can be connected by using an HDMI-toDVI adapter cable. (This may not work with some TVs and
displays, resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital
Content Protection)*2, so only HDCP-compatible
components can display the picture.
Supported Audio Formats
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz,
16/20/24 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio)
Your Blu-ray Disc/DVD player must also support the
HDMI output of the above audio formats.
About Copyright Protection
The AV receiver supports HDCP (High-bandwidth Digital
Content Protection)*2, a copy-protection system for digital
video signals. Other devices connected to the AV receiver
via HDMI must also support HDCP.
*1
*2
*3
DVI (Digital Visual Interface): The digital display interface
standard set by the DDWG*3 in 1999.
HDCP (High-bandwidth Digital Content Protection): The
video encryption technology developed by Intel for
HDMI/DVI. It’s designed to protect video content and requires
a HDCP-compatible device to display the encrypted video.
DDWG (Digital Display Working Group): Lead by Intel,
Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon
Image, this open industry group’s objective is to address the
industry’s requirements for a digital connectivity specification
for high-performance PCs and digital displays.
Note
• The HDMI video stream is compatible with DVI (Digital Visual
Interface), so TVs and displays with a DVI input can be
connected by using an HDMI-to-DVI adapter cable. (Note that
DVI connections only carry video, so you’ll need to make a
separate connection for audio.) However, reliable operation with
such an adapter is not guaranteed. In addition, video signals from
a PC are not supported.
• The HDMI audio signal (sampling rate, bit length, etc.) may be
restricted by the connected source component. If the picture is
poor or there’s no sound from a component connected via HDMI,
check its setup. Refer to the connected component’s instruction
manual for details.
The AV receiver’s HDMI interface is based on the
following:
Audio Return Channel, 3D, x.v.Color, DeepColor, Lip
Sync, DTS-HD Master Audio, DTS-HD High
Resolution Audio, Dolby TrueHD, Dolby Digital Plus,
DSD and Multichannel PCM.
En-114
Appendix
Network/USB Features
Connecting to the Network
The following diagram shows how you can connect the AV
receiver to your home network. In this example, it’s
connected to a LAN port on a router, which has a 4-port
100Base-TX switch built-in.
Internet radio
Modem
WAN
LAN
Router
Network Requirements
■ Ethernet Network
For the best results, a 100Base-TX switched Ethernet
network is recommended. Although it’s possible to play
music on a computer that’s connected to the network
wirelessly, playback may be unreliable, so it is
recommended to use wired connections.
■ Ethernet Router
A router manages the network, data-routing and supplying
of IP addresses. Your router must support the following:
• NAT (Network Address Translation). NAT allows
several networked computers to access the Internet
simultaneously via a single Internet connection. The AV
receiver needs Internet access for Internet radio.
• DHCP (Dynamic Host Configuration Protocol). DHCP
supplies IP addresses to the network devices, allowing
them to configure themselves automatically.
• A router with a built-in 100Base-TX switch is
recommended.
Some routers have a built-in modem, and some Internet
Service Providers (ISP) require you to use specific routers.
Please consult your ISP or computer dealer if you’re
unsure.
■ CAT5 Ethernet cable
Use a shielded CAT5 Ethernet cable (straight-type) to
connect the AV receiver to your home network.
Computer or media server
■ Internet Access (for Internet radio)
To receive Internet radio, your Ethernet network must have
Internet access. A narrowband Internet connection (e.g.,
56K modem, ISDN) will not provide satisfactory results,
so a broadband connection is strongly recommended (e.g.,
cable modem, xDSL modem, etc.). Please consult your ISP
or computer dealer if you’re unsure.
Note
• To receive Internet radio with the AV receiver, your broadband
Internet connection must be working and able to access the Web.
En-115
Consult your ISP if you have any problems with your Internet
connection.
• The AV receiver uses DHCP to configure its network settings
automatically. If you want to configure these settings manually,
see “Network” (➔ page 82).
• The AV receiver does not support PPPoE settings, so if you have
a PPPoE-type Internet connection, you must use a PPPoEcompatible router.
• Depending on your ISP, you may need to specify a proxy server
to use Internet radio. If your computer is configured to use a
proxy server, use the same settings for the AV receiver
(➔ page 82).
Server Requirements
■ Server playback
The AV receiver can play digital music files stored on a
computer or media server and supports the following
technologies:
• Windows Media Player 11
• Windows Media Player 12
• Windows Media Connect 2.0
• DLNA-certified media server
If the operating system of your computer is Windows
Vista, Windows Media Player 11 is already installed.
Windows Media Player 11 for Windows XP can be
downloaded for free from the Microsoft web site.
• The computer or media server must be on the same
network as the AV receiver.
• Up to 20,000 folders can be displayed, and folders may
be nested up to 16 levels deep.
Note
• Depending on the media server, the AV receiver may not
recognize it, or may not be able to play its music files.
Appendix
Minimum system requirements for Windows Media
Player 11 on Windows XP
Operating system
Windows XP Home Edition (SP2), Windows XP
Professional (SP2), Windows XP Tablet PC Edition
(SP2), Update Rollup 2 for Windows XP Media Center
Edition 2005 (KB900325), October 2006 Update Rollup
for Windows XP Media Center Edition (KB925766)
Processor:
233 MHz Intel Pentium II, Advanced
Micro Devices (AMD), etc.
Memory:
64 MB
Hard disk:
200 MB of free space
Drive:
CD or DVD drive
Modem:
28.8 kbps
Sound card:
16-bit sound card
Monitor:
Super VGA (800 x 600)
Video card:
64 MB VRAM, DirectX 9.0b
Software:
Microsoft ActiveSync (only when
using a Windows Mobile-based Pocket
PC or smartphone)
Web browser: Microsoft Internet Explorer 6 or
Netscape 7.1
■ Remote playback
• Windows Media Player 12
• DLNA-certified (within DLNA Interoperability
Guidelines version 1.5) media server or controller device.
The setting varies depending on the media server or
controller devices. Refer to your devices’ instruction
manual for details.
If the operating system of your personal computer is
Windows 7, Windows Media Player 12 is already installed.
For more information, see the Microsoft web site.
USB Device Requirements
• USB mass storage device class (but not always
guaranteed).
• FAT16 or FAT32 file system format.
• If the storage device has been partitioned, each section
will be treated as an independent device.
• Up to 20,000 folders can be displayed, and folders may
be nested up to 16 levels deep.
• USB hubs and USB devices with hub functions are not
supported.
Note
• If the media you connect is not supported, the message “No
Storage” will be displayed.
• If you connect a USB hard disk drive to the AV receiver’s USB
port, we recommend that you use its AC adapter to power it.
• The AV receiver supports USB MP3 players that support the
USB Mass Storage Class standard, which allows USB devices to
be connected to computers without the need for special drivers or
software. Note that not all USB MP3 players support the USB
Mass Storage Class standard. Refer to your USB MP3 player’s
instruction manual for details.
• Protected WMA music files on an MP3 player cannot be played.
• Onkyo accepts no responsibility whatsoever for the loss or
damage to data stored on a USB device when that device is used
with the AV receiver. We recommend that you back up your
important music files beforehand.
• MP3 players containing music files that are managed with special
music software are not supported.
• Operation is not guaranteed for all USB devices, which includes
the ability to power them.
• Do not connect your USB device via a USB hub. The USB device
must be connected directly to the AV receiver’s USB port.
• If the USB device contains a lot of data, the AV receiver make
take a while to read it.
• USB devices with security functions cannot be played.
En-116
Supported Audio File Formats
For server playback and playback from a USB device, the
AV receiver supports the following music file formats.
Variable bit-rate (VBR) files are supported. However,
playback times may not display correctly.
Note
• With remote playback, the AV receiver does not support the
following music file formats: FLAC, Ogg Vorbis, DSD and
Dolby TrueHD.
• In the case of server playback, the above-mentioned file formats
may not be played depending on the server type.
■ MP3 (.mp3 or .MP3)
• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3
format with sampling rates of 8 kHz, 11.025 kHz,
12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz and bitrates of between 8 kbps and 320 kbps.
Incompatible files cannot be played.
■ WMA (.wma or .WMA)
WMA stands for Windows Media Audio and is an audio
compression technology developed by Microsoft
Corporation. Audio can be encoded in WMA format by
using Windows Media® Player.
• WMA files must have the copyright option turned off.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, bitrates of
between 5 kbps and 320 kbps, and WMA DRM are
supported.
• WMA Pro/Voice formats are not supported.
■ WMA Lossless (.wma or .WMA)
• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
are supported.
• Quantization bit: 16 bit, 24 bit
Appendix
■ WAV (.wav or .WAV)
WAV files contain uncompressed PCM digital audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
■ AAC
(.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/
.3GP or .3G2)
AAC stands for MPEG-2/MPEG-4 Audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz and bitrates of between 8 kbps and
320 kbps are supported.
■ FLAC (.flac or .FLAC)
FLAC is a file format for lossless audio data compression.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
■ DSD (.dsf or .DSF)
• The sampling rate of 2.8224 MHz is supported.
■ Dolby TrueHD (.vr/.mlp/.VR/.MLP)
• Sampling rates of 48 kHz, 64 kHz, 88.2 kHz, 96 kHz,
176.4 kHz and 192 kHz are supported.
About DLNA
The Digital Living Network Alliance is an international,
cross-industry collaboration. Members of DLNA develop a
concept of wired and wireless interoperable networks
where digital content such as photos, music, and videos can
be shared through consumer electronics, personal
computers, and mobile devices in and beyond the home.
The AV receiver complies with the DLNA Interoperability
Guidelines version 1.5.
License and Trademark
Information
“x.v.Color” is a trademark of Sony Corporation.
Manufactured under license under U.S. Patent No’s: 5,956,674;
5,974,380; 5,978,762; 6,487,535; 6,226,616; 7,212,872;
7,003,467; 7,272,567; 7,668,723; 7,392,195; 7,930,184;
7,333,929; 7,548,853; 7,283,634 & other U.S. and worldwide
patents issued and pending. DTS-HD, the Symbol, & DTS-HD
and the Symbol together are registered trademarks & DTS-HD
Master Audio is a trademark of DTS, Inc. Product includes
software. ©DTS, Inc. All Rights Reserved.
Manufactured under license from Dolby Laboratories. Dolby,
Pro Logic, Surround EX and the double-D symbol are
trademarks of Dolby Laboratories.
Music Optimizer™ is a trademark of Onkyo Corporation.
■ Ogg Vorbis (.ogg or .OGG)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and
bitrates of between 48 kbps and 500 kbps are supported.
Incompatible files cannot be played.
“HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.”
■ LPCM (Linear PCM)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz and 96 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
*
InstaPrevue and the InstaPrevue logo are trademarks or
registered trademarks of Silicon Image, Inc. in the United States
and other countries.
Only for playback via network.
■ Apple Lossless (.m4a/.mp4/.M4A/.MP4)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,
88.2 kHz and 96 kHz are supported.
• Quantization bit: 16 bit, 24 bit
En-117
Appendix
THX and the THX logo are trademarks of THX Ltd. which may
be registered in some jurisdictions. All rights reserved.
THX Ultra2 Plus
Before any home theater component can be
THX Ultra2 Plus certified, it must pass a rigorous series
of quality and performance tests. Only then can a product
feature the THX Ultra2 Plus logo, which is your
guarantee that the Home Theater products you purchase
will give you superb performance for many years to
come. THX Ultra2 Plus requirements define hundreds of
parameters, including power amplifier performance, and
pre-amplifier performance and operation for both digital
and analog domains. THX Ultra2 Plus receivers also
feature proprietary THX technologies (e.g., THX Mode)
which accurately translate movie soundtracks for home
theater playback.
Manufactured under license from Audyssey Laboratories™, Inc.
U.S. and foreign patents pending. Audyssey MultEQ® XT32,
Audyssey Dynamic EQ®, Audyssey Dynamic Volume® and
Audyssey DSX® are registered trademarks of
Audyssey Laboratories, Inc.
“MHL, the MHL Logo, and Mobile High-Definition Link are
trademark or registered trademarks of MHL LLC in the United
States and other counties.”
HD Radio Technology manufactured under license from iBiquity
Digital Corporation. U.S. and Foreign Patents. HD Radio™ and
the HD, HD Radio, and “Arc” logos are proprietary trademarks
of iBiquity Digital Corp.
“DLNA®, the DLNA Logo and DLNA CERTIFIED™ are
trademarks, service marks, or certification marks of the Digital
Living Network Alliance.”
iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and
iPod touch are trademarks of Apple Inc., registered in the U.S.
and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to
meet Apple performance standards. Apple is not responsible for
the operation of this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
Apple TV is a trademark of Apple Inc., registered in the U.S. and
other countries.
This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property rights of
Rovi Corporation. Reverse engineering and disassembly are
prohibited.
Windows and the Windows logo are trademarks of the Microsoft
group of companies.
Qdeo and QuietVideo are trademarks of Marvell or its affiliates.
HQV® (Hollywood Quality Video) is a trademark of
Qualcomm Incorporated.
“Xantech” is a registered trademark of Xantech Corporation.
“Niles” is a registered trademark of Niles Audio Corporation.
Re-Equalization and the “Re-EQ” logo are trademarks of
THX Ltd.
VLSC™ is a trademark of Onkyo Corporation.
En-118
Appendix
Specifications
Amplifier Section
Rated Output Power
All channels:
(North American)
140 watts minimum continuous power per
channel, 8 ohm loads, 2 channels driven
from 20 Hz to 20 kHz, with a maximum
total harmonic distortion of 0.05% (FTC)
(Australian)
9 ch × 200 W at 6 ohms, 1 kHz, 1 ch driven
of 1% (IEC)
Maximum Effective Output Power
(Australian)
9 ch × 250 W at 6 ohms, 1 kHz, 1 ch driven
(JEITA)
Dynamic Power*
* IEC60268-Short-term maximum output power
320 W (3 Ω, Front)
270 W (4 Ω, Front)
160 W (8 Ω, Front)
THD+N (Total Harmonic Distortion+Noise)
0.05% (20 Hz - 20 kHz, half power)
Damping Factor
60 (Front, 1 kHz, 8 Ω)
Input Sensitivity and Impedance (Unbalance)
200 mV/47 kΩ (LINE)
2.5 mV/47 kΩ (PHONO MM)
Rated RCA Output Level and Impedance
1 V/470 Ω (PRE OUT)
Maximum RCA Output Level and Impedance
5.5 V/470 Ω (PRE OUT)
Phono Overload
70 mV (MM 1 kHz 0.5% Direct)
Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (LINE)
Tone Control Characteristics
±10 dB, 50 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio 110 dB (LINE, IHF-A)
80 dB (PHONO MM, IHF-A)
Speaker Impedance
4 Ω - 16 Ω
Video Section
Supported
Input Sensitivity/Output Level and Impedance
1 Vp-p/75 Ω (Component Y)
0.7 Vp-p/75 Ω (Component PB/CB, PR/CR)
1 Vp-p/75 Ω (Composite)
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB
3D, Audio Return Channel, DeepColor,
x.v.Color, Lip Sync, CEC (RIHD), HDMI
ZONE 2
■ Video Inputs
Component
Composite
Analog RGB
IN 1, IN 2
IN 1, IN 2, IN 3, IN 4, AUX
PC IN
■ Video Outputs
Tuner Section
FM Tuning Frequency Range
(North American) 87.5 MHz - 107.9 MHz
(Australian) 87.5 MHz - 108.0 MHz, RDS
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40
Digital Tuner
(North American) HD Radio
Component
Composite
MONITOR OUT
MONITOR OUT, ZONE 2 OUT
■ Audio Inputs
Digital
Analog
Optical: 2 (Rear), 1(Front)
Coaxial: 3
BD/DVD, CBL/SAT, STB/DVR, GAME 1,
PC, TV/CD, PHONO, AUX
■ Audio Outputs
General
Analog
Power Supply
(North American) AC 120 V, 60 Hz
(Australian) AC 220 - 240 V, 50/60 Hz
Power Consumption (North American) 11.0 A
(Australian) 1015 W
No-sound Power Consumption
(North American) 150 W
(Australian) 145W
Stand-by Power Consumption
(North American) 0.10 W
(Australian) 0.15 W
Dimensions (W × H × D)
435 mm × 198.5 mm × 455.0 mm
17-1/8" × 7-13/16" × 17-15/16"
Weight
24.5 kg (54.0 lbs.)
■ HDMI
Input
Output
Video Resolution
Audio Format
IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, IN 7, IN 8,
AUX INPUT
OUT MAIN, OUT SUB/ZONE 2 OUT
1080p
Dolby TrueHD, DTS-HD Master Audio,
DVD-Audio, DSD
En-119
PREOUT, ZONE 2 PRE/LINE OUT,
ZONE 3 PRE/LINE OUT,
ZONE 4 PRE/LINE OUT
Analog Multichannel Pre Outputs
11
Subwoofer Pre Outputs
4, ZONE 2 SW, ZONE 3 SW, ZONE 4 SW
Speaker Outputs
Main [L, R, C, SL, SR, SBL/Z4L, SBR/Z4R]
+ Front Wide/ZONE 2 (L, R) + Front
High/ZONE 3 (L, R)/Passive SW
Phones
1 (6.3 ø)
■ Others
Setup Mic
RS232
RI
USB
Ethernet
IR Input
IR Output
12 V Trigger Out
1
1
1
1 (Front)/1 (Rear)
1
2
1
3
Specifications and features are subject to change
without notice.
Integra Division of
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650
http://www.integrahometheater.com
Integra Division of
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.integra.eu
Integra Division of
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.integra.com.cn
Integra Division of
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
http://www.integraworldwide.com
En
Y1206-1
SN 29401258
(C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.
* 2 9 4 0 1 2 5 8 *
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising