Integra | DTR-50.6 | Owner Manual | Integra DTR-50.6 Receiver Owner Manual

Integra DTR-50.6 Receiver Owner Manual
DTR-50.6
Basic Manual
Advanced Manual found here
http://integraworldwide.com/manual/dtr506/adv/en.html
En
Before Start
Advanced Manual
Advanced Manual is always updated with the latest
information and its user friendly interface, which does not
matter whether you access from PC or Smartphone, helps
you to understand more deeply about the AV Receiver.
Advanced Manual is consisted of the following chapters.
r Details on AM/FM Playback
r Playing Music Files on a USB Storage Device
r Listening to Internet Radio
r Playing Music with DLNA
r Playing Music Files in a Shared Folder
r Operating Music Files with the Remote Controller
r Listening Mode
r Advanced Settings
r Operating Other Components with the Remote Controller
r Advanced Speaker Connection
r Connecting and Operating Onkyo RI Components
r Control Function between the Unit and External Component
r Firmware Update
r Troubleshooting
r Reference Information
Supplied Accessories
Indoor FM antenna --- (1)
AM loop antenna --- (1)
Color labels for speaker cable --- (1)
Speaker Cable
1
r Equipped with 7 channel amplifier
r THX Select2 Plus certified
r Incorporates Qdeo™ technology for HDMI video
upscaling
r Equipped with 4K/60 Hz Passthrough-compatible HDMI
IN/OUT jacks (only IN1 to IN4 support 4K)
r Supports the HDMI Through function which allows
transmission from playback devices to the TV in standby
state
r Supports HDCP2.2, a strict copy-protection for providing
high quality content (HDMI IN3/OUT MAIN only)
r Supports ARC (Audio Return Channel)
r Supports USB storage playback
r Supports variety of network functions such as Internet
Radio, DLNA, etc.
r Supports MHL-enabled mobile device
r Bi-Amping capability
r Lip Sync function to correct deviation of audio and video
r Multi-zone function which allows you to play a different
source in another room from the main room (Video can
also be played in Zone 2)
r 32 bit DSP (Digital Signal Processor) with excellent
calculation performance
r Music Optimizer™ for Compressed Digital Music files
r Phase Matching Bass System
r Automatic speaker setup available using supplied
calibrated microphone (AccuEQ Room Calibration)
r Supports playback of MP3, WMA, WMA Lossless, FLAC,
WAV, Ogg Vorbis, Apple Lossless, DSD, Dolby TrueHD
via network and USB storage device (the supported
formats will differ depending on the use environment)
r ISF (Imaging Science Foundation) Video Calibration
2
Features
The Basic Manual leads you through the fundamental steps
to enjoy the AV Receiver from connections to TV, speaker
system and playback components, to necessary functions
for playback. As well as that, Basic Manual informs you with
the instructions on frequently used functions. Besides, there
is another part of the manual called Advanced Manual to
inform you with more detailed information, which we have
decided to publish on the web from the ecological point of
view.
3
About the Basic Manual
Remote controller (RC-883M) --- (1)
Batteries (AA/R6) --- (2)
Power cord --- (1)
Speaker setup microphone --- (1)
¼
The number in parenthesis indicates the quantity. On packaging, the letter
at the end of the product name indicates the color.
How to use the remote controller
Remote control sensor
AV Receiver
Batteries (AA/R6)
Approx.
16 ft. (5 m)
Advanced Manual found here
http://integraworldwide.com/manual/dtr506/adv/en.html
2
¼
If you do not use the remote controller for a long time, remove the
batteries to prevent leakage.
¼
Note that keeping consumed batteries inside may cause corrosion
resulting in damage of the remote controller.
Step 1: Connections
TV
HDMI
IN
Personal computer
HDMI
OUT
To use the ARC function, connect to the
ARC compatible HDMI jack of the TV and
make an appropriate setting on the unit.
See "2nd Step : Source Connection" of
"Step 2: Setting Up".
HDMI cable
HDMI
OUT
HDMI
OUT
HDMI
OUT
Game console
1
Set-top box/Digital
video recorder, etc.
Connecting the TV and players
Important: The power cord must be connected only after all
other connections are completed.
HDMI Cable Connection
The unit has many HDMI jacks on its rear panel and each
of them corresponds to an input selector button of the same
name on the front panel. For example, a Blu-ray Disc player
will be connected to the IN 1 jack and the BD/DVD button
on the front panel will be used to listen to the playback
sound (if the player is CEC compliant, input will be switched
automatically). If you add another Blu-ray Disc player, you
can use any other jack than IN 1. It is possible to change
assignment of the input jacks and input selector buttons.
HDMI
OUT
Blu-ray Disc/
DVD player
Satellite/Cable
set-top box, etc.
For how to make settings, see the Advanced Manual (http://
integraworldwide.com/manual/dtr506/adv/en.html).
To connect the TV and the unit, connect the HDMI OUT
MAIN jack of the unit and the HDMI IN jack of the TV using
an HDMI cable. With this connection, it becomes possible to
display the setting screen of the unit on the TV or transmit
video/audio signals from the player to the TV. If your TV
supports ARC (Audio Return Channel), it is possible to
play the TV sound with the AV receiver's speakers with this
connection only. If your TV does not support ARC, you need,
in addition to the HDMI OUT MAIN jack connection, a digital
optical cable connection between the digital audio out optical
jack of the TV and the DIGITAL IN OPTICAL jack of the unit
or an analog audio (RCA) cable connection between the
audio output jack of the TV and the TV/CD analog audio
input jack of the unit.
z
Connection with a TV not supporting ARC
TV
DIGITAL
OPTICAL
OUT
AUDIO
OUT
¼ Select an appropriate
connection for your TV.
Another TV can be connected to the HDMI OUT SUB jack.
In this case, press Monitor Out on the main unit several
times to display "SUB" or "MAIN+SUB" and select the
output method. With the sub output, the operation screen
for Internet function or USB playback can be displayed.
3
Step 1: Connections
It is also possible to use the multi-zone function with this
jack. For details, see the section 5 "Using the multi-zone
function" of "Step 3: Playing Back".
The unit supports the HDMI Through function that allows
transmission from players to the TV even if the unit is in
standby. You have to modify the settings to enable the input
selection link with CEC compliant device, connection with
ARC compatible TV, and HDMI Through function. See "2nd
Step : Source Connection" of "Step 2: Setting Up".
r To enjoy HDCP2.2 protected video, connect the player to
the IN3 jack and the TV to the HDMI OUT MAIN jack of
the unit. Your player and TV need to support HDCP2.2.
r To play 4K or 1080p video, use the high speed HDMI
cable.
r It is possible to send video and audio of an MHLenabled mobile device by connecting the MHL-enabled
mobile device to the AUX Input HDMI/MHL jacks on the
front panel.
Connecting Components without HDMI
If your AV component does not have HDMI jack, use an
available jack of your component for cable connection with
this unit. Just as the HDMI jacks, other jacks on this unit
have a preassigned input selector button on the front panel.
See the name of the input selector button shown with the
jack when connecting the device.
„ Audio signal connection
Analog audio (RCA) cable
5
4
1
3 Connection with turntable: If it uses an MM type
cartridge and does not have a built-in audio equalizer,
connect it to the 3 PHONO jack. If the connected
turntable has a built-in audio equalizer, connect it to the
2 TV/CD jack.
¼
If it uses an MC type cartridge, install an audio equalizer compatible
with MC type cartridge between the unit and the turntable by
connecting it to the 2 TV/CD jack. For details, refer to the turntable's
instruction manual.
¼
If the turntable has a ground wire, connect it to the GND terminal of
this unit. If connecting the ground wire increases noise, disconnect it.
„ Video signal connection
The unit has a video upconversion function. For details, see
the section on the right.
4 Use a component video cable to connect a TV
with component video input jacks and a player with
component video output jacks.
Component video cable
¼
Its transmitted video has higher quality than
that of composite video cable.
5 Use a composite video cable to connect a TV with
composite video input jack or a player with composite
video output jack.
3
2
Video signals input to the composite video input
jack or the COMPONENT VIDEO input jacks will be
upconverted to HDMI signals and then output from
the HDMI output jack.
Note that it is not possible to convert digital audio
input signals to analog or vice versa.
Composite video cable
1 Digital connection: Use a digital optical cable
(OPTICAL) or digital coaxial cable (COAXIAL) for
connection with a player.
Digital optical cable (OPTICAL)
¼
As the digital in optical jack of the unit has a
cover, push in the cable of the player against
the cover as it is turned inside.
Digital coaxial cable (COAXIAL)
2 Analog connection: Use an analog audio (RCA) cable
for connection with a player.
To enjoy multi-zone playback of audio of a CD player or
such other player without HDMI output jack, you need
to use the RCA cable to connect the corresponding
jacks of the player and this unit. For details on the multizone function, see the section 5 "Using the multi-zone
function" of "Step 3: Playing Back".
4
AV Receiver
¼
When you upconvert video signals input to the
COMPONENT VIDEO jacks and output them from the
HDMI OUT jack, set the output resolution of the player
to 480i/576i. If the input has 480p/576p or higher
resolution, a message prompting you to change the
resolution setting will appear. If your player does not
support 480i/576i output, use the composite video jack.
¼
If multiple video signal inputs are put into one input
system, the output will be made in the order of HDMI,
component video, and composite video.
Step 1: Connections
2
2
Front R
Connecting speakers
F
Height R
1
Front L
H
Wide R
Important: The power cord must be connected only after all
other connections are completed.
12
3 9F
9
Wide L
3
Center
G
Height L
6
GH
45
78
12
3
45
6
78
9F
GH
Front speakers
Center speaker
Surround speakers
Subwoofer
Surround back speakers
Height speakers
Wide speakers
r 5.1 ch: 1 2 3 4 5 6
r 7.1 ch: 1 2 3 4 5 6 + 7 8 or
1 2 3 4 5 6 + 9 F or
123456+GH
r Up to two subwoofers can be connected.
r To use the multi-zone function, see the section 5 "Using
the multi-zone function" of "Step 3: Playing Back".
If there is only one
surround back
speaker, connect it to
the BACK L terminal.
6
Subwoofer with builtin power amplifier
6
Subwoofer with builtin power amplifier
5
8
Surround R Surround back R
Important: %QPPGEVURGCMGTUYKVJŝVQŝKORGFCPEG
You have to modify the setting if any of the speakers have
ŝQTOQTGVQNGUUVJCPŝKORGFCPEG;QWECPUGVWRD[
viewing the guidance displayed on the TV screen. Select
the item with the cursor buttons of the remote controller
7
4
Surround back L Surround L
and press Enter to confirm your selection. To return to the
previous screen, press Return. Press Receiver and then
Home on the remote controller. Select "Setup" - "2.Speaker
Setup" - "Speaker Settings" - "Speaker Impedance" and
change the default value from "6ohms" to "4ohms".
5
Step 1: Connections
1/2"-5/8"(12-15 mm)
Cut and remove the plastic coating from the end of the
speaker cable, twist the core and connect it to the terminal.
Make correct connection between the unit's jacks and
speaker's jacks (+ to + and - to -) for each channel. If
connection is wrong, a bass sound may become poor
due to reverse phase. Attaching the supplied colored
speaker cable labels to the + side on the both ends of
each channel's cable will help correct connection. The
subwoofer jack supports connection of a subwoofer with
built-in power amplifier. Set the cut-off filter selection
switch of the subwoofer to DIRECT. If the subwoofer does
not have a cut-off filter selection switch but has a cut-off
frequency adjusting dial, turn it to the maximum frequency.
If your subwoofer does not have built-in power amplifier,
you can connect a power amplifier between the unit and the
subwoofer.
r The speaker setting is 7.1 ch at the time of purchase.
You can change it manually or by using automatic
speaker setting.
r Short-circuiting the + cable and - cable or contacting the
cable core to the rear panel of the unit may cause failure.
Also do not connect two or more cables to one speaker
terminal or one speaker to several terminals.
r Using a speaker with less impedance than the setting
may result in failure.
When using commercially available banana plugs:
tighten the speaker terminals to the end and then insert the
banana plugs. Do not insert the cable core directly into the
hole for banana plug of speaker terminal.
(North American model)
You can enjoy Internet radio and DLNA by connecting the
unit to LAN. Connect the Ethernet cable to the Ethernet
port of the router.
Internet radio
3
Other connections
Router
AM/FM Antenna Connections
Connect the antennas to listen to AM/FM broadcast. When
listening to the broadcast for the first time, adjust the
antenna position and orientation to get the best reception.
AM loop antenna (supplied)
Indoor FM antenna
(supplied)
Fix with a tack on
the wall.
(North American model)
(Other models)
Assemble the AM loop antenna (supplied).
6
Network Connection
PC
NAS
Headphones Connection
%QPPGEVUVGTGQJGCFRJQPGUYKVJCUVCPFCTFRNWI |KPEJ
or ø 6.3 mm) to the PHONES jack on the front panel.
Sound from the speakers will be off while you are using the
headphones.
r If you selected any other listening mode than Stereo,
Mono and Direct, connecting headphones will switch the
listening mode to Stereo.
Step 2: Setting Up
Important: When the unit is turned on for the first time, the
setup wizard of the section 2 will automatically be launched.
If you use the setup wizard to make the initial setup,
connect a TV to the HDMI OUT MAIN jack of the unit via
HDMI connection.
1
Turning the power on
Connect the power cord to the outlet. Press zOn/Standby
on the main unit or zReceiver on the remote controller to
turn the unit on or to standby mode.
2
Making the Initial Setup with the Setup
Wizard
Read before starting the procedure: Set up by
answering the guidance displayed on the TV screen.
Select the item with the cursor buttons of the remote
controller and press Enter to confirm your selection.
To return to the previous screen, press Return.
r If you terminate the procedure on the way or
change the setting made in the initial setup and
want to call up the setup wizard again, press
Receiver and then Home on the remote controller,
select "Setup" - "7.Hardware Setup" - "Initial
Setup", and press Enter.
„ 1st Step : AccuEQ Room Calibration
The test tone coming from each speaker will be measured to
enable setting of the number of speakers, volume level, each
speaker's optimum crossover frequencies, and distance from
the primary listening position, and also enable correction of
distortion caused by the room acoustic environment.
Initial Setup
AccuEQ Room Calibration
This step you can automatically calibrate
your room to get correct surround sound.
Would you like to cailbrate your room now
or later?
Do it Now
Do it Later
HOME
Exit
Initial Setup
Select the language first. In the next screen, the summary
of the setup wizard as below will be displayed. Select "Yes"
in this screen and press Enter on the remote controller.
Language Select
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
HOME Exit
Initial Setup
1. Place the speaker setup microphone.
When the start screen above is displayed, before
starting the procedure, place the supplied speaker setup
microphone at the measurement position  by referring
to the figure below.
Welcome to initial setup. Have you connected all the speakers and devices?
Before starting, please connect speakers and sources.
Now, would you like to start initial setup?
TV
1st Step : AccuEQ Room Calibration
2nd Step : Source Connection
3rd Step : Remote Mode Setup
4th Step : Network Connection
Yes
¼
This unit includes a removable power cord. Connect the power cord to
AC INLET of the unit and then connect to the outlet. Always disconnect
the outlet side first when disconnecting the power cord. When the
unit is turned on, a large instantaneous current may flow affecting
functionality of the computer and other devices. It is recommended to
use a separate outlet from that for the computer or such other sensitive
devices.
Firmware update notification: If the unit is connected via
LAN and there is firmware update available, the "Firmware
Update Available" message will appear. To execute
updating, select "Update Now" with the cursor buttons of
the remote controller and press Enter. When "Completed!"
appears, press zOn/Standby on the main unit to turn the
unit into standby mode. Then updating will be completed.
No
HOME
Exit
The setup wizard proceeds in the four steps as below.
„ 1st Step : AccuEQ Room Calibration
„ 2nd Step : Source Connection
„ 3rd Step : Remote Mode Setup
„ 4th Step : Network Connection
Listening area
Measurement position
with microphone
¼
Correct measurement will not be possible if the microphone is held by
hand. Measurement is not possible if headphones are being used.
¼
The subwoofer sound may not be detected since it is extremely low
frequencies. Raise the subwoofer volume to around the half of its
maximum volume and make its frequency to the maximum level.
¼
A loud test tone will be heard during measurement. Measurement may
be interrupted if there is ambient noise or radio frequency interference.
Close the window and turn off the home appliance and fluorescent light.
7
Step 2: Setting Up
2. After placing the microphone at the measurement
position, select "Do it Now" in the start screen and
press Enter.
3. Connect the microphone to the Setup Mic jack of the
unit.
Setup Mic jack
Speaker
setup
microphone
4. Follow the guidance displayed on the TV screen.
6. When the measurement is completed, the
measurement result is displayed.
Press W/X on the remote controller to check the
settings. Press Enter with "Save" selected. In the next
screen showing that "AccuEQ Room Calibration" is
"On", press Enter on the remote controller.
r If there is an error message, follow the on-screen
instruction to remove the error cause.
About THX playback
THX recommends setting the speakers manually if you
use THX-certified speakers or playing back with THX
listening modes.
r THX recommends setting the crossover frequency to
“80Hz(THX)” manually.
r Due to the electrical complexities and the interaction
with the room, you may notice irregular results when
setting the level or distance of each speaker. If this
happens, THX recommends setting the speakers and
the subwoofer manually.
AccuEQ Room Calibration
Front Speakers Type
Powered Zone 2
Normal
7. When "Please unplug setup microphone." is
No
Back/Height
Back
Subwoofer
Yes
displayed, disconnect the microphone.
cursors and press Enter.
r If you select "No" and press Enter, the error cause
will be displayed. Follow the guidance to remove the
error cause and check the connection again.
4. Select "Yes" with the cursors and press Enter on the
remote controller to check the connection of other
inputs or select "No, Done Checking" and press
Enter to skip.
If you select "Yes", you will return to the screen of step 2.
If you select "No, Done Checking", you will proceed to
step 5.
5. Enabling HDMI Linked Operation and Other
Functions
In the next screen, you can enable the HDMI linked
operation with CEC compliant device, connection
with ARC compatible TV, and HDMI Through function.
Select "Yes" with the cursors to enable them or "No,
Done Checking" to skip, and press Enter on the remote
controller.
6. Select "Yes" with the cursors and press Enter to
enable the CEC link function or select "No" and
press Enter to keep it disabled.
Source Connection
„ 2nd Step : Source Connection
Set bi-amp only if you use 2 channel amp for each front speaker.
3. After checking the connection, select "Yes" with the
The following CEC-compatible devices are found;
ENTER
Next
When the screen above is displayed, set the items with
the cursors on the remote controller. When the cursor
is on an item, the content of the item will be shown on
the lower left of the screen. After setting the items, press
Enter on the remote controller. Press Enter also in the
next screen,
5. The test tones sound from the connected speakers
and automatic speaker setting starts.
Measurement will be made twice for each speaker. It
takes several minutes to be completed. Keep the room
as quiet as possible during measurement. If any of
the speakers do not produce the test tone, check for
disconnection.
You can check whether or not each input source is
connected correctly.
Integra DHS-8.8
1. When the Source Connection start screen is
displayed, select "Yes, Continue" with the cursors
and press Enter.
Yes
No
HOME
Exit
Initial Setup
If you select "Yes", the connection with ARC compatible
TV and HDMI Through function will be set to "Auto" and
enabled.
Source Connection
This step will start to check if the
connections were made correctly.
Would you like to continue?
Yes. Continue
No. Skip
HOME
Exit
2. Select the desired input to check the connection and
press Enter.
Start playback of the selected device. If connection is
correct, video/audio of the input source selected on the
unit will be played.
8
Do you wish to turn on the CEC link?
Step 2: Setting Up
„ 3rd Step : Remote Mode Setup
„ 4th Step : Network Connection
In this step, you can enable operation of the other
components using the remote controller of the unit. When
the Remote Mode Setup start screen is displayed, select
"Yes" with the cursors and press Enter on the remote
controller. Follow the guidance to select the desired Remote
Mode button and in the keyboard screen, enter the first
three characters of the brand name of the device you are
going to program (e.g., "INT" for Integra) and search for the
remote control code. The guidance will also explain how to
set the remote controller.
Initial Setup
Network Connection
Do you want to connect network connection?
It gives you network services that our AV
receiver support. If you wish to skip this step.
select “No. Skip”.
Yes
No. Skip
HOME
Exit
You can check the network connection. When the Network
Connection start screen is displayed, select "Yes" with the
cursors and press Enter on the remote controller. If you
select "Yes" in the next screen, you can view the Ethernet
cable connection status.
Initial Setup
Remote Mode Setup
Preprograming remote will give you control
of other devices from AV receiver remote
Would you like to setup your remote to
control your devices? This may take a while
depending on what and how many you have
connected. You can always come back to remote
setup from setup “8-2 Remote Mode Setup”.
„ Exiting the Setup Wizard
Yes
No. Skip
HOME
Exit
After finishing the initial setup, keep "Finished" selected
and press Enter on the remote controller. Connection and
setting of the unit is now completed. See Step 3 and enjoy
your home theater.
9
Step 3: Playing Back
1
Playing the player and TV
1
7
8
Remote Controller Parts Name
1 z Receiver button: Turns the unit on or into standby
mode.
2 Remote Mode/Input Selector button: Switches the
input to be played.
2
3 Cursor buttons and Enter button: Moves the cursor
9
F
z To control the unit: You can control any other device
than this unit if you register the specified remote control
code to 2 Remote Mode. As the remote controller may be
in the remote mode that enables control of other devices,
be sure to press 9 Receiver to select the Receiver mode
(for controlling this unit) before operating the unit.
1. Turning the power on
Press 1 zReceiver on the remote controller to turn the
power on.
r Switch the input on the TV to that assigned to the
unit. Use the TV's remote controller.
2. Select the input of the unit and start playback on the
player or TV.
r Press 2 Input Selector to which the desired player
has been assigned. Press TV/CD to play the TV's
sound. You can also use the input selector buttons on
the main unit.
r Input will automatically be selected if the TV or player
is CEC compliant and connected to the unit with
HDMI cable.
3. Select the desired listening mode.
Press the 5 listening mode buttons to switch the mode
so that you can enjoy different listening modes. For
details about the listening modes, see "Listening Modes"
on the next section.
4. Adjust the volume with G.
10
G
5
6
7
8
3
4
and confirms the selection.
4 Q Setup button: Displays the Quick Setup menu that
H
I
9
F
G
H
I
J
5
allows you to set the frequently used functions including
input selection and volume adjustment.
Listening mode buttons: Allows you to select the
listening mode.
Dimmer button: Switches the brightness of the display.
Zone button : For use when the unit is connected with
an integrated amplifier in a separate room and sound is
played there.
Sleep button: Allows the unit to enter standby
automatically when the specified time elapses.
Receiver button: Switches the remote controller to the
mode for operating this unit.
Muting button: Temporarily mutes audio.
VOLUME buttons: Allows you to adjust the volume.
Return button: Returns the display to the previous
state.
Home button: Displays the Home menu that allows you
to make advanced settings and use Internet radio and
DLNA.
Display button: Switches the information on the display.
r The buttons other than those above are for operating
other devices.
6
J
Step 3: Playing Back
Listening Modes
Select the desired mode by switching and listening actual
sound in different modes. The selectable listening modes
depend on the format of the input signals.
Movie/TV: You can select a listening mode suitable for
movies and TV programs.
Music: You can select a listening mode suitable for music.
Game: You can select a listening mode suitable for games.
THX: You can select a THX listening mode.
r For details on the listening modes, see the Advanced
Manual (http://integraworldwide.com/manual/dtr506/adv/
en.html).
"Direct" for playing the input signals as-is
Selecting this mode allows the input signals to be
played as they are. For example, 2 ch signals of music
CD will be played in stereo, 5.1 ch signals in 5.1 ch,
and Dolby Digital signals of blu-ray disc or DVD in the
Dolby Digital sound field according to the specified
number of channels.
„ Muting Temporarily: Press Muting on the remote
controller. Press Muting again to cancel muting.
„ Changing the Display Brightness: Press Dimmer on
the remote controller several times to select the desired
brightness.
„ Changing the Input Display: Press Display on the
remote controller several times to switch the display of the
main unit in order of:
2
Listening to AM/FM Radio
The Basic Manual explains the method using automatic
tuning. For manual tuning, see the Advanced Manual
(http://integraworldwide.com/manual/dtr506/adv/en.html).
1. Press Tuner on the main unit several times to select
either "AM" or "FM".
2. Press Tuning Mode on the main unit, so that the
Input source &
volume
Listening mode
Signal format
"AUTO" indicator on the display stays lit.
3. Press Tuning j l on the main unit.
The automatic tuning to a radio station starts. Searching
stops when one is tuned. When tuned into a radio
station, the "cTUNEDd" indicator on the display stays
lit. The "FM STEREO" indicator lights if the radio station
is an FM radio station.
TUNED
AUTO
Sampling
frequency
FM STEREO
Other Useful Functions
„ Playing Video and Audio from Different Sources: It
is possible to play audio and video from different sources.
For example, you can play audio from the CD player and
video from the BD/DVD player. In this case, press BD/DVD
and then TV/CD. Then start playback on the BD/DVD player
and CD player. This function is effective when an input with
audio only has been selected (TV/CD, Tuner or Phono in
the initial setting).
„ Adjusting Sound Quality: It is possible to enhance or
moderate the bass and treble of front speakers. Press Tone
on the main unit several times to select the desired setting
from "Bass", "Treble", and "PM Bass" (Phase Matching
$CUU CPFCFLWUVYKVJ Ũ
"Bass": Allows you to enhance or moderate the bass.
"Treble": Allows you to enhance or moderate the treble.
"PM Bass": Allows you to keep the clear midrange and
effectively enhance the bass.
Input signal
resolution
Output resolution
r If "Dolby D 5.1" is displayed in signal format, the
Dolby Digital 5.1 ch signals are being input. When
listening to AM/FM radio, the band, frequency and
preset number are displayed.
Registering an AM/FM Radio Station
It allows you to register up to 40 of your favorite AM/FM
radio stations.
1. Tune into the AM/FM radio station you want to
register.
2. Press Memory on the main unit.
The preset number on the display flashes.
3. Repeatedly press Preset d c on the main unit to
select a number between 1 and 40 while the preset
number is flashing (about 8 seconds).
4. Press Memory on the main unit again.
When registered, the preset number stops flashing.
To select a preset radio station, press Preset d c on
VJGOCKPWPKVQT%* ŨQPVJGTGOQVGEQPVTQNNGT
11
Step 3: Playing Back
3
Using the Home menu
In the Home menu, you can make advanced setup
and use Internet radio and DLNA function. For details
on the operation, see the Advanced Manual (http://
integraworldwide.com/manual/dtr506/adv/en.html).
1. After pressing Receiver, press Home on the remote
controller.
The Home menu is displayed on the TV screen. You can
also use the Home button on the main unit.
HOME
Setup
2. Select the item with the cursor buttons of the remote
controller and press Enter to confirm your selection.
To return to the previous screen, press Return. To return
to the Home menu, press Home.
„ Sleep Timer: Select to turn the unit into standby mode
automatically when the specified time elapses.
„ InstaPrevue: Select to preview videos input from the
HDMI input jacks collectively in a single screen. The screen
has a main window (current input video) and sub windows
(other input videos). To switch the current input, select the
desired sub window with the cursor buttons and press
Enter.
r A black sub window is shown for the input with no video
signals.
r "InstaPrevue" cannot be selected if the video is being
input from HDMI IN 5 or 6 or if there is no signal from
the input currently selected.
r Depending on video signals, the picture may not be
properly rendered on the preview thumbnails.
r 1080p or higher resolution is not supported.
„ Setup: You can change the assignment of input terminals
and input selector buttons and also make various speaker
settings and other advanced settings.
12
„ Network Service: Select to use Internet radio services
and the DLNA function. When you connect the unit to
the network and press Enter, the network service screen
will be displayed on the TV. On the TV screen, select the
desired service or music file with the cursors of the remote
controller and press Enter to confirm and start playback.
Internet radio service: You can listen to TuneIn or such
other Internet radio stations registered in advance.
DLNA : You can play music files stored in the PC or
NAS device connected to the network. Select the server
with the cursors, select the desired music file and press
Enter to start playback.
Home Media: You can play music files in a shared folder
on the PC or NAS device connected to the network.
Select the server with the cursors, select the desired
music file and press Enter to start playback.
r "Network Service" becomes selectable after the network
starts up even if it cannot be selected first. It may take
about a minute to start up.
r When "Network Service" is selected for the first time,
the "DISCLAIMER" screen will appear on the TV. Select
"Agree" if you agree the content. If you do not agree the
content, you cannot use the network service.
¼
You cannot use the function unless the TV is connected via HDMI
since selecting "Agree" in the "DISCLAIMER" screen is not possible.
4
Using Quick Setup menu
In the Quick Setup menu, you can set frequently used
functions including input selection and volume adjustment.
1. Press Q Setup on the remote controller.
The Quick Setup menu is displayed on the connected
TV's screen.
CBL/SAT
Input
BD DVD
Audio
CBL/SAT
Video
STB DVR
Information
GAME
Listening Mode
PC
AUX
2. Select the item with the cursor buttons of the remote
controller and press Enter to confirm your selection.
r To return to the previous screen, press Return.
„ Input: Select the input and check the assignment of
input selector buttons.
„ Audio:
r Layout of the icons in the "Network Service" top menu
can be changed. Press NET on the remote controller
and press D. Select the source icon with the cursors
and press Enter, and then select the destination icon
and press Enter. The positions of the icons are switched
each other.
A/V Sync: If the video is behind the audio, you can
delay the audio to offset the gap.
r It cannot be set when audio is played from the TV's
speakers.
r It cannot be set if the input is "NET" or "USB".
r It cannot be set if the listening mode is Direct.
„ USB: Select "USB" in the TV screen and connect a USB
storage device to the USB port on the front panel. On the
TV screen, select the desired folder or music file with the
cursors of the remote controller and press Enter to confirm
and start playback.
r "USB" becomes selectable after the USB function starts
up even if it cannot be selected first. It may take about a
minute to start up.
Bass, Treble: It is possible to enhance or moderate the
bass and treble of front speakers.
r It cannot be set if the listening mode is Direct or THX.
Phase Matching Bass: Allows you to keep the clear
midrange and effectively enhance the bass.
r It cannot be set if the listening mode is Direct or THX.
Subwoofer Level, Center Level: Adjust the speaker
level while listening to the sound. The adjustment you
made will be reset to the previous status when you turn
the unit to standby mode.
r The speakers cannot be adjusted if they have been
set to "No" or "None" in "Speaker Configuration".
Step 3: Playing Back
AccuEQ Room Calibration: Disables the sound field
set in the automatic speaker setting. The setting can be
separately set to each input.
r This setting cannot be selected if the automatic
speaker setting has not been performed.
r It cannot be set if headphones are connected or the
listening mode is Direct.
Late Night: Make small sounds to be easily heard. It
is useful when you need to reduce the volume while
watching a movie late night. You can enjoy the effect
on Dolby Digital, Dolby Digital Plus and Dolby TrueHD
sources only.
r Turning the unit to standby mode will set the setting
to "Off". In case of Dolby TrueHD, the setting will be
set to "Auto".
Music Optimizer: Improve the quality of the
compressed audio. Playback sound of lossy compressed
files such as MP3 will be improved. The setting can be
separately set to each input.
r The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream
signals.
r It cannot be set if the listening mode is Direct.
Re-EQ, Re-EQ (THX): Adjust the soundtrack that was
processed to enhance its treble, in order to make it
suitable for home theater.
r In Re-EQ, the following listening modes can be used:
Dolby Digital, Dolby Digital Plus, Dolby TrueHD,
Multichannel, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio, DTS Express, DSD, Dolby
EX, Dolby PLIIz Height, Dolby PLIIx Movie, DTS
Neo:6 Cinema, and 5.1ch source + DTS Neo:6.
r In Re-EQ (THX), the following listening modes can
be used: THX Cinema, THX Surround EX, and THX
Select2 Cinema.
Speaker Layout: You can give priority to surround back
speakers, height speakers or wide speakers when they
are all connected.
r The speakers cannot be selected if they have been
set to "None" in "Speaker Configuration". Also the
setting cannot be changed if any two or more of
surround back speakers, height speakers and wide
speakers are set to "None".
r The setting cannot be used in the following cases.
– "Front Speakers Type" is set to "Bi-Amp".
– The listening mode being used is not compatible
with surround back speakers, front height
speakers or front wide speakers.
„ Video:
Monitor Out: The video input signals input to the unit
will be converted by the unit when they are output from
the HDMI OUT jack to the TV so that their resolution can
match that of the TV used. Select the HDMI OUT jack to
be used for output.
Wide Mode: You can set the aspect ratio.
Picture Mode: You can adjust the image quality.
"Cinema" will automatically adjust the image to be
suitable to watch movie and "Game" suitable to play
game. In "Standard", the resolution will be changed but
the image quality will not be adjusted. In "Custom", "ISF
Day" and "ISF Night", you can adjust the brightness,
contrast, hue and saturation as desired. If you do not
adjust the resolution and image quality, select "Bypass".
r "Wide Mode" and "Picture Mode" can be set only on
the video output from the HDMI OUT MAIN jack.
r "Video" cannot be selected if the input is "NET" or
"USB".
„ Information:
Audio: Displays the audio input source, format, number
of channels, sampling frequency, listening mode,
number of output channels, and other audio information.
Video: Displays the video input source, resolution,
signal format, color tone, 3D information, Aspect, Picture
Mode, output, and other Video information.
Tuner: Displays the band, frequency, preset number,
and other tuner (radio) information.
„ Listening Mode: Select the listening mode from the
categories of "MOVIE/TV", "MUSIC", "GAME" and "THX".
r It cannot be set when audio is played from the TV's
speakers.
13
Step 3: Playing Back
5
Using the multi-zone function
The function allows you to connect the unit with a TV or audio
equipment placed in a separate room so that you can enjoy
audio and video of the connected equipment even if you are
staying in a different room. It is possible to perform playback
in the main room and a separate room at the same time,
for example by playing the Blu-ray Disc player in the main
room where the unit is placed while playing Internet radio in
a separate room. It is also possible to perform playback only
in a separate room. There are three methods to configure
multi-zone connection as described in "a" to "c" in the right.
Simultaneous playback in all zones is also possible.
¼1 Supported by HDMI IN1 to IN4 and AUX Input HDMI/MHL jacks.
¼2 When you connect a CD player or such other player without HDMI
output jack, connect it to the analog audio input jacks of the unit.
Multi-zone output is not possible if the connection is only with digital
optical cable or digital coaxial cable. In case of analog connection,
analog audio output setting may be necessary on the player.
r As for HDMI input and analog audio input, it is possible
to play the same source or different sources in the main
room and separate room.
r As for the "NET" and "USB", you cannot select different
audio sources for the main room and separate room. For
example, if "NET" has been selected in the main room
and then "USB" is selected as playback source in the
separate room, the input in the main room will change to
"USB" accordingly.
r When listening to AM/FM broadcasting, you cannot
select different stations for the main room and separate
room. Therefore broadcasting of the same station will be
heard in the both rooms.
r If you play the same HDMI connected player for the main
room and a separate room, the sound field processing
for 2 ch PCM signals will be made in a separate room.
Outputting Video/Audio to a Separate Room
Change the setting: Press Receiver and then Home on
the remote controller, select "Setup" - "1.Input/Output
Assign" - "Monitor Out" - "Zone 2 Monitor Out" and set the
setting to "Use".
r You can view the information of the connected device
on the TV of Zone 2 by pressing Display during Zone 2
playback.
r The CEC link function does not work with the TV in a
separate room.
Listening to Music in a Separate Room
„ b. Connecting a Integrated Amplifier in a
separate room
It is possible to play 2 ch source in a separate room while
7.1 ch source is being played in the main room. Connect
the ZONE2 PRE/LINE OUT jacks or ZONE3 PRE/LINE
OUT jacks of the unit and the line-in jacks of the integrated
amplifier in a separate room with an RCA cable. In a
separate room, you can enjoy sound from an external
player connected to the HDMI input jack or the analog
audio input jacks of the unit, sound from the "NET" or
"USB" source, and the AM/FM broadcasting.
„ a. Connecting a TV in a separate room
You can play video and audio of the HDMI connected player
on the TV in a separate room. With an HDMI cable, connect
between the HDMI OUT ZONE2 jack of the unit and the
HDMI IN jack of the TV in a separate room.
Main room
Zone 2
Zone 2
Zone 3
r In a separate room, you can enjoy sound from an external
device connected to the HDMI input jack (¼1) or the
analog audio input jacks (¼2) of the unit, sound from the
"NET" or "USB" source, and the AM/FM broadcasting.
14
Zone 2
Zone 3
r Volume can be adjusted with both the unit and the
integrated amplifier used in a separate room. To adjust
it with the unit, press Receiver and then Home on the
remote controller, select "Setup" - "7.Hardware Setup" "Multi Zone" - "Zone 2 Out" or "Zone 3 Out" and set the
setting to "Variable". If you connect a power amplifier, be
sure to make the setting and adjust the volume on the
unit.
Step 3: Playing Back
„ c. Connecting Speakers in a Separate Room
It is possible to directly connect the speakers in another
room without an amplifier. Connect the speakers in another
room to the ZONE2 speaker terminals of the unit using
speaker cables. Note that 5.1 ch will be the maximum in the
main room during Zone 2 playback. In a separate room, you
can enjoy sound from an external player connected to the
HDMI input jack or the analog audio input jacks of the unit,
sound from the "NET" or "USB" source, and the AM/FM
broadcasting.
Performing Multi-zone Playback
1. Press Zone on the remote controller several times to
select either Zone 2 or Zone 3.
The Zone button stays lit red when Zone 2 is selected
and green when Zone 3 is selected.
2. Point the remote controller at the remote controller
sensor and press zReceiver.
"Z2" or "Z3" lights on the main unit display and the multizone function is enabled.
3. Press Zone on the remote controller several times
again to select Zone 2 or Zone 3 and press Input
Selector of the input to be played in a separate
room.
If you turn the unit to standby during multi-zone
playback, the Z2/Z3 indicators are dimmed and the
playback mode is switched to playback in a separate
room only. Performing steps 1 and 3 while the unit is in
standby also switches the playback mode to playback in
a separate room only.
r While Zone 2 or Zone 3 is on, the RI linked system
function (interlink between Onkyo components) is
disabled.
WHOLE HOUSE MODE: If you press Whole House
Mode while playback is being performed in the main
room, the WHOLE HOUSE MODE is turned on, "Z2"
and "Z3" on the display light at the same time and the
playback sources of all the rooms are switched to the
same source at once.
r WHOLE HOUSE MODE is effective only for
playback of the external player connected to the
analog audio input jacks.
r This function cannot be used if headphones are
connected or audio is output from the speakers
of the TV.
To control on the main unit: Press Zone 2 or Zone 3 and
within 8 seconds, press the input selector button of the
input to be played in a separate room. To play the same
source in the main room and separate room, press Zone 2
or Zone 3 twice.
Zone 2
Change the setting: Press Receiver and then Home on
the remote controller, select "Setup" - "2.Speaker Setup" "Speaker Settings" and set "Powered Zone2" to "Yes".
r Adjust the volume on this unit.
To turn off the multi-zone function: Press Zone on the
remote controller several times to select Zone 2 or Zone 3
and press zReceiver. Alternatively press Off on the main
unit.
To adjust the volume: Press Zone on the remote controller
several times to select Zone 2 or Zone 3 and adjust with
VOLj/l. To control on the main unit, press Zone 2 or Zone
3 and within 8 seconds, adjust with the Master Volume
control.
To mute temporarily: Press Zone on the remote controller
several times to select Zone 2 or Zone 3 and press Muting.
To adjust the sound quality and balance for a separate
room: Press Zone 2 on the main unit and press Tone
several times to display "Bass", "Treble" or "Balance" on the
main unit display. Display the desired setting on the display
and adjust it with + or -.
r Muting and adjustment of sound quality and balance
is not effective if "Zone 2 Out" or "Zone 3 Out" is set to
"Fixed".
r If Zone 2 or Zone 3 is on, power consumption during
standby becomes larger than normal.
15
1
L
M
2
N
3
4
5
6
7
P
O
8
9
F
G H
(Other models)
I
Q
J
K
R
Front Panel
1 zOn/Standby button: Turns the unit on or into standby mode.
2 Hybrid Standby indicator: Stays lit if the unit enters
3
4
5
6
7
8
standby when the HDMI Through and network standby
are enabled.
Monitor Out button: Allows you to select the HDMI jack to
output the video input signals that are input to the unit.
Remote control sensor: Receives signals from the
remote controller.
Tone and Tone Level buttons: Adjusts the high tone
and low tone.
Display
Listening Mode buttons: Allows you to select the
listening mode.
Dimmer button (North American model): Switches the
brightness of the display.
16
9
F
G
H
I
J
K
L
RT/PTY/TP button (Other models): Can be used when
receiving the station transmitting text information.
Memory button: Registers or deletes a station.
Tuning Mode button: Switches the tuning mode.
Display button: Switches the information on the display.
Home button: Displays the Home menu.
Cursor buttons, Tuning j l button, Preset d c
button and Enter button: Moves the cursor and
confirms the selection. When listening to AM/FM
broadcasting, tune into the station with Tuning j l or
select the registered station with Preset d c.
Return button: Returns the display to the previous state.
Master Volume: Allows you to adjust the volume.
Zone 2 button, Zone 3 button and Off buttons:
Controls the multi-zone function.
M Whole House Mode button: Controls the WHOLE
N
O
P
Q
R
HOUSE MODE function to play the same source in all
the multi-zone connected rooms.
Phones jack: Stereo headphones with a standard plug
are connected.
Setup Mic jack: The supplied speaker setup
microphone is connected.
Input selector buttons: Switches the input to be played.
USB port: A USB storage device is connected so that
music files stored in it can be played.
AUX Input HDMI/MHL jacks: An HD video camera or
MHL-enabled mobile device is connected. It is possible to
send video and audio of an MHL-enabled mobile device.
AUX Input Video/Audio jacks: A video camera or such
other device is connected.
1 23
4
5
6
7
8
9
F
1 23
4
5
6
9
7
8
Display
1 Stays lit in the following conditions. "Z2" "Z3": Zone 2 or
Zone 3 output is on. / "HDMI": HDMI signals are input
and HDMI input selector is selected. / "ARC": Audio
signals are input from ARC compatible TV and TV/CD
input selector is selected. / "3D": Input signals are 3D. /
"USB" (¼): "USB" input is selected and USB storage
device is connected. / "NET" (¼): "NET" input is selected
and the unit is connected to the network. / "DIGITAL":
Digital signals are input and the digital input selector is
selected. / Cursor indicators: NET or USB is controlled.
¼
"USB" and "NET" will flash if the connection is not correct.
G
H
I
J
K
L
M
1 RI REMOTE CONTROL jack: An Onkyo product with RI
2
3
4
5
6
7
¼
Special devices or cable connections are necessary to use the control
functions (5) to (7). Contact the specialized stores for more information.
F
G
H
I
J
K
L
8 HDMI IN/OUT jacks: Digital video signals and audio
signals are transmitted between the unit and the
connected devices.
9 HDBaseT™ IN/OUT ports: HDMI input signals are
output via the Ethernet cable. As they are covered with
the listening mode.
5 Stays lit while Music Optimizer is enabled.
6 Stays lit in the following conditions. "AUTO": Tuning
Rear Panel
jack can be connected and synchronized with this unit.
(/#06'00#LCEM ŝ CPF#/#06'00#
terminal: The supplied antennas are connected.
COMPONENT VIDEO IN/OUT jacks: Component video
input/output jacks
ETHERNET port: Used for LAN connection
RS232 port: Connected to the home control system. (¼)
IR IN A/B/OUT jack: Connected to the multiroom
remote control kit. (¼)
12V TRIGGER OUT A/B/C jacks: Allows you to connect
a device with 12V trigger input jack in a separate room
to enable link operation between the device and the unit.
(¼)
2 Stays lit while headphones are connected.
3 Stays lit while NET or USB is controlled.
4 Stays lit according to the type of input digital signals and
M
a seal when shipped, remove it when you use the ports.
Do not use the ports to connect the Ethernet port of
network device.
AC INLET: The power cord is connected.
DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio
signals are input.
GND terminal: The ground wire of the turntable is
connected.
Composite video and analog audio jacks: Analog
video signals and audio signals are input.
MONITOR OUT V jack: Video signals are output to the
connected monitor or TV.
PRE OUT jacks: A power amplifier or subwoofer with
built-in amplifier is connected.
PRE/LINE OUT ZONE2/ZONE3 jacks: Audio output
jacks connected to the integrated amplifier for multi-zone
playback in a separate room.
SPEAKERS terminals: Speakers are connected. To
use the Multi-zone function, connect the speakers in the
separate room to the ZONE2 speaker terminals.
mode is auto. / "fTUNEDe": Receiving AM/FM radio.
fe flashes while tuning is automatically performed. /
"FM STEREO": Receiving FM stereo. / "RDS" (Other
models): Receiving RDS broadcasting.
7 "MUTING": Flashes when muting is on.
8 Stays lit in the following conditions. "SLEEP": Sleep
timer has been set. / "ASb" (Auto Standby): Auto
Standby is on. / "ch": Channel is being set. / "Hz":
Crossover frequencies are being set. / "m/ft": Speaker
distances are being set. / "dB": Speaker volume is being
set.
9 Displays various information of the input signals.
Pressing Display displays the type of input digital signals
and the listening mode.
17
Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the power
on/off or disconnecting/connecting the power cord,
which is easier than working on the connection,
setting and operating procedure. Try the simple
measures on both the unit and the connected
device. If the problem is that the video or audio is not
output or the HDMI linked operation does not work,
disconnecting/connecting the HDMI cable may solve
it. When reconnecting, be careful not to wind the
HDMI cable since if wound the HDMI cable may not fit
well. After reconnecting, turn off and on the unit and
the connected device.
HDMI control does not function correctly.
r Set the CEC link function of the unit to on. It is also
necessary to make the HDMI linked system setting on
the TV. See the TV's instruction manual for details.
The remote controller does not work.
r Be sure to press Receiver first before operating the unit
with the remote controller.
There is no sound for multi-zone function.
r The AV receiver will automatically enter standby mode
when Auto Standby is set and launched.
r When you connect a CD player or such other player
without HDMI output jack, connect it to the analog audio
input jacks of the unit. Multi-zone output is not possible if
the connection is only with digital optical cable or digital
coaxial cable. In case of analog connection, analog
audio output setting may be necessary on the player.
There’s no sound, or it’s very quiet.
Cannot access to network.
r A wrong input selector button has been selected. Select
a correct input for the player. Also check that Muting is
not on.
r Not all listening modes use all speakers.
r Try plugging/unplugging the unit or router, or check their
power-on status. This will work well in many cases.
The AV receiver turns off unexpectedly.
„ Resetting the Unit
Resetting the unit to the status at the time of shipment may
solve the problem. If the measures above do not solve the
problem, reset the unit with the following procedure. If you
reset the unit status, your preferences will be reset to the
defaults. Note them down before starting reset.
z How to reset:
1. While holding down CBL/SAT on the main unit (note
that step 2 must be performed with this button
pressed down)
2. Press zOn/Standby on the main unit ("Clear"
appears on the display and the unit returns to
standby)
Clear
2. Press zOn/Standby.
holding down
1. While
CBL/SAT,
There’s no picture.
r A wrong input selector button has been selected.
r To display video from the connected player on the TV
screen while the unit is in standby, you need to enable
HDMI Through function.
r When the TV image is blurry or unclear, power cord or
connection cables of the unit may have interfered. In
that case, keep distance between TV antenna cable and
cables of the unit.
r If you connect a player supporting HDCP2.2, be sure to
connect it to the HDMI IN3 jack of the unit. At the time,
connect the TV to the HDMI OUT MAIN jack.
z How to reset the remote controller:
1. While holding down Receiver on the remote
controller, press Home until Receiver stays lit (about
3 seconds)
2. Within 30 seconds, press Receiver again
Receiver
Home
18
Specifications
Amplifier Section
General
Rated Output Power
All channels: 130 watts minimum continuous power per channel,
|QJONQCFUEJCPPGNUFTKXGPHTQO*\VQM*\YKVJC
maximum total harmonic distortion of 0.08% (FTC)
(North American)
7 ch × 180 W at 6 ohms, 1 kHz, 1 ch driven of 1% (IEC) (Others)
Maximum Effective Output Power
7 ch × 215 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) (Asian)
Dynamic Power (¼)
¼
IEC60268-Short-term maximum output power
9 ŝ(TQPV
9 ŝ(TQPV
9 ŝ(TQPV
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz - 20 kHz, half power)
Damping Factor
(TQPVM*\ŝ
Input Sensitivity and Impedance (Unbalance)
O8Mŝ .+0'
O8Mŝ 2*101//
Rated RCA Output Level and Impedance
O8ŝ 24'17624'.+0'176
Maximum RCA Output Level and Impedance
8ŝ 24'17624'.+0'176
Phono Overload
70 mV (MM 1 kHz 0.5% Direct)
Frequency Response
5 Hz - 100 kHz/+1 dB, –3 dB (Direct mode)
Tone Control Characteristics
±10 dB, 20 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
106 dB (LINE, IHF-A)
80 dB (PHONO MM, IHF-A)
Speaker Impedance
ŝŝ
Power Supply
AC 120 V, 60 Hz (North American)
AC 220 - 240 V, 50/60 Hz (Others)
Power Consumption
8.1 A (North American)
720 W (Others)
0.1 W (Stand-by, North American)
0.2 W (Stand-by, Others)
90 W (No-sound)
Dimensions (W × H × D)
435 mm × 198.5 mm × 388.5 mm
17-1/8" × 7-13/16" × 15-5/16"
Weight
15.5 kg (34.2 lbs.)
Video Section
Input Sensitivity/Output Level and Impedance
8RRŝ %QORQPGPV;
8RRŝ %QORQPGPV2B/CB, PR/CR)
8RRŝ %QORQUKVG
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz (North American)
87.5 MHz - 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40
Network Section
Ethernet LAN
10BASE-T/100BASE-TX
Speaker Outputs
FRONT L/ R, CENTER, SURROUND L/R, BACK L/R,
HEIGHT/Bi-AMP L/R, WIDE/ZONE 2 L/R
Phones
PHONES (Front, ø 6.3)
z Others
Setup Mic
1 (Front)
RS232
1
Ethernet
1
IR IN 2 (A/B)/IR OUT
1
12V TRIGGER OUT
3 (A/B/C)
USB
1 (Front)
RI
1
HDBaseT OUT ETHERNET(CAT 5e/6) 1/IN 1 (HDMI)
Specifications and features are subject to change without notice.
z HDMI
Input
IN1 (BD/DVD, 4K), IN2 (CBL/SAT, 4K), IN3 (STB/DVR, 4K, HDCP2.2),
IN4 (GAME, 4K), IN5 (PC), IN6, AUX INPUT (HDMI/MHL) (Front)
Output
OUT MAIN (ARC, HDCP2.2), OUT SUB/ZONE2
Video Resolution
Pass through: 4K 60 Hz (YCbCr 4:2:0)
Upscaling: 4K 30 Hz
Audio Format
DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD,
Dolby Digital Plus, DSD, Multichannel PCM
Supported
3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD),
4K (Upscaling and Passthrough)
z HDBaseT
OUT ETHERNET(CAT 5e/6)/IN (HDMI)
z Video Inputs
Component
IN (CBL/SAT)
Composite
IN1 (CBL/SAT), IN2 (STB/DVR), IN3 (GAME), AUX Input (Front)
z Video Outputs
Component
OUT
Composite
MONITOR OUT
z Audio Inputs
Digital
OPTICAL 1 (GAME), 2 (TV/CD)
COAXIAL 1 (BD/DVD), 2 (CBL/SAT), 3(STB/DVR)
Analog
BD/DVD, CBL/SAT, STB/DVR, GAME, PC, TV/CD, PHONO, AUX Input (Front)
z Audio Outputs
Analog
ZONE2 PRE/LINE OUT, ZONE3 PRE/LINE OUT
Analog Multichannel Pre Outputs
FRONT L/ R, CENTER, SURROUND L/R, BACK or HEIGHT or
WIDE L/R, 2 SUBWOOFER PRE OUT
DISCLAIMER
Through this device you are able to link to other services or websites which
are not under the control of any company which has designed, manufactured
or distributed/have distributed this device, and its affiliates (collectively,
“Company”). We have no control over the nature, content and availability
of those services. The inclusion of any links does not necessarily imply a
recommendation or endorse the views expressed within them.
All information, content and services available through this device belong to
third parties and are protected by copyright, patent, trademark and/or other
intellectual property laws of applicable countries.
The information, content and services provided through this device are for your
personal, noncommercial use only. Any information, content or services may
not be used in any manner other than previously approved by the appropriate
content owner or service provider.
You may not modify, copy, republish, translate, exploit, create derivative works,
upload, post, transmit, sell or distribute in any manner any information, content
or services available through this device, unless expressly permitted by the
appropriate copyright, patent, trademark and/or other intellectual property
owner, including, without limitation, content owner or service provider.
THE CONTENT AND SERVICES AVAILABLE THROUGH THIS DEVICE ARE
PROVIDED “AS IS”.
COMPANY DOES NOT WARRANT INFORMATION, CONTENT OR SERVICES
SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE.
COMPANY EXPRESSLY DISCLAIMS ANY WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF TITLE, NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
Company makes no representation or warranty of any kind, express or implied,
about the completeness, accuracy, validity, legality, reliability, suitability or
availability with respect to the information, content or services available through
this device. Company shall not be liable, whether in contract or tort, including
negligence and strict liability, for any direct, indirect, special, incidental or
consequential damages or any other damages arising out of, or in connection
with, any information contained in, or as a result of the use of any content or
service by you or any third party, even if Company has been advised of the
possibility of such damages, nor shall Company be liable for any third party
claims against users of this device or any third party.
In no event shall Company be responsible nor liable for, without limiting the
generality of the foregoing, any interruption or suspension of any information,
content or service available through this device. Company is neither responsible
nor liable for customer service related to the information, content and services
available through this device. Any question or request for service relating to
the information, content or services should be made directly to the appropriate
content owners and services providers.
19
License and Trademark Information
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,
Surround EX and the double-D symbol are trademarks of Dolby Laboratories.
THX Select2 Plus
Before any home theater component can be THX Select2 Plus certified, it must pass
a rigorous series of quality and performance tests. Only then can a product feature
the THX Select2 Plus logo, which is your guarantee that the Home Theater products
you purchase will give you superb performance for many years to come. THX
Select2 Plus requirements define hundreds of parameters, including power amplifier
performance, and pre-amplifier performance and operation for both digital and analog
domains. THX Select2 Plus receivers also feature proprietary THX technologies (e.g.,
THX Mode) which accurately translate movie soundtracks for home theater playback.
InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks
of Silicon Image, Inc. in the United States and other countries.
Apple, iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and
other countries.
Apple TV is a trademark of Apple Inc., registered in the U.S. and other countries.
“Theater-Dimensional” and “Theater-Dimensional (logo)” are trademarks of
Onkyo Corporation.
AccuEQ, Music Optimizer, RIHD and WRAT are trademarks of Onkyo Corporation.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing
Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks,
and DTS-HD Master Audio is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
Qdeo and QuietVideo are trademarks of Marvell or its affiliates.
“RIHD” and “RIHD (logo)” are trademarks of Onkyo Corporation.
®
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio
Inc. and its subsidiaries. All rights reserved.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are trademarks, service
marks, or certification marks of the Digital Living Network Alliance.
This product is protected by certain intellectual property rights of Microsoft. Use
or distribution of such technology outside of this product is prohibited without a
license from Microsoft.
Windows and the Windows logo are trademarks of the Microsoft group of
companies.
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd.
Safari is a trademark or registered trademark of Apple Computer, Inc. in the
United States.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
“x.v.Color” is a trademark of Sony Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
Manufactured under license from THX Ltd. THX and the THX logo are
registered in the U.S. and other jurisdictions. All rights reserved. Surround EX is
a trademark of Dolby Laboratories. Used with permission.
U.S. Pat. nos. 7,254,239 & 7,593,533 & 7,974,425 & 8,452,028 & 8,509,457
Taiwan Pat. I238671 European Pat. 1,360,874
“Xantech” is a registered trademark of Xantech Corporation.
“Niles” is a registered trademark of Niles Audio Corporation.
“MHL, the MHL Logo, and Mobile High-Definition Link are trademarks or
registered trademarks of MHL LLC in the United States and other counties.”
“All other trademarks are the property of their respective owners.”
Integra Division of
Integra Division of
Integra Division of
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650
http://www.integrahometheater.com
1301, 555 Tower, No.555 West NanJin Road, Jin an,
Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.integra.com.cn
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku,
OSAKA 541-0041, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
http://www.integraworldwide.com
Integra Division of
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.integra.eu
D1406-1
SN 29401775A
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 7 7 5 A *
Notes
En Cs
Step 3: Playing Back
5
Using the multi-zone function
The function allows you to connect the unit with a TV or audio
equipment placed in a separate room so that you can enjoy
audio and video of the connected equipment even if you are
staying in a different room It is possible to perform playback
in the main room and a separate room at the same time,
for example by playing the Blu ray Disc player in the main
room where the unit is placed while playing Internet rad o in
a separate room It is also possible to perform playback only
in a separate room There are three methods to configure
multi zone connection as described in "a" to "c" in the right
Simultaneous playback in all zones is also possible
1 Supported by HDMI IN1 to IN4 and AUX Input HDMI/MHL jacks
2 When you connect a CD player or such other player w thout HDMI
output jack connect it to the analog audio nput jacks of the unit
Multi zone output is not possible if the connection is only w th dig tal
optical cab e or dig tal coaxial cab e In case of analog connection
analog audio ou put set ing may be necessary on the player
@ As for HDMI input and analog audio input, it is possible
to play the same source or different sources in the main
room and separate room
@ As for the "NET" and "USB", you cannot select different
audio sources for the main room and separate room For
example, if "NET" has been selected in the main room
and then "USB" is selected as playback source in the
separate room, the input in the main room will change to
"USB" accordingly
@ When listening to AM/FM broadcasting, you cannot
select different stations for the main room and separate
room Therefore broadcasting of the same station will be
heard in the both rooms
@ If you play the same HDMI connected player for the main
room and a separate room, the sound field processing
for 2 ch PCM signals will be made in a separate room
Outputting Video/Audio to a Separate Room
Change the setting Press Receiver and then Home on
the remote controller, select "Setup" "1 Input/Output
Assign" "Monitor Out" "Zone 2 Monitor Out" and set the
setting to "Use"
@ You can view the information of the connected device
on the TV of Zone 2 by pressing Display during Zone 2
playback
@ The CEC link function does not work with the TV in a
separate room
Listening to Music in a Separate Room
2
b. Connecting a Integrated Amplifier in a
separate room
It is possible to play 2 ch source in a separate room while
7 1 ch source is being played in the main room Connect
the ZONE2 LINE OUT jacks or ZONE3 LINE OUT jacks of
the unit and the line in jacks of the integrated amplifier in a
separate room with an RCA cable In a separate room, you
can enjoy sound from an external player connected to the
HDMI input jack or the analog audio input jacks of the unit,
sound from the "NET" or "USB" source, and the AM/FM
broadcasting
a. Connecting a TV in a separate room
You can play video and audio of the HDMI connected player
on the TV in a separate room With an HDMI cable, connect
between the HDMI OUT ZONE 2 jack of the unit and the
HDMI IN jack of the TV in a separate room
Ma n room
Zone 2
Zone 2
Zone 3
@ In a separate room, you can enjoy sound from an external
device connected to the HDMI input jack (1) or the
analog audio input jacks (2) of the unit, sound from the
"NET" or "USB" source, and the AM/FM broadcasting
Zone 2
Zone 3
@ Volume can be adjusted with both the unit and the
integrated amplifier used in a separate room To adjust
it with the unit, press Receiver and then Home on the
remote controller, select "Setup" "7 Hardware Setup"
"Multi Zone" "Zone 2 Out" or "Zone 3 Out" and set the
setting to "Variable" If you connect a power amplifier, be
sure to make the setting and adjust the volume on the
unit
14
1
English P.14 1
! " #$%&# #'()# *+,- !.
English P.14 2
!
#$%&# #'()# *+,- !.
Ё᭛˄ㅔԧᄫ˅
31
噝೼ऩ⣀᠓䯈Ёˈ
ᙼৃҹሑѿᴹ㞾䖲᥹㟇ᴀᴎ+'0,䕧ܹ᥹ষ˄ˆ˅៪῵ᢳ䷇乥䕧ܹ᥹ষ˄ˆ˅ⱘ໪䚼䆒໛ⱘໄ䷇ˈᴹ
㞾
Ā1(7ā៪
Ā86%ā⑤ⱘໄ䷇ˈҹঞ$0)0ᑓ᪁DŽ
Ё᭛˄ㅔԧᄫ˅
32
೼ऩ⣀᠓䯈Ёˈ
ᙼৃҹሑѿᴹ㞾䖲᥹㟇ᴀᴎ+'0,䕧ܹ᥹ষ៪῵ᢳ䷇乥䕧ܹ᥹ষⱘ໪䚼᪁ᬒᴎⱘໄ䷇ˈᴹ㞾Ā1(7ā៪
Ā86%ā⑤ⱘໄ䷇ˈ
ҹঞ$0)0ᑓ᪁DŽ
Remarks
& - / ".
໛⊼
᠔ᔎ䇗ⱘࡳ㛑ҙ
೼ =RQH Ёৃ
⫼DŽ
D1407-0
SN29355931
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
* 2 9 3 5 5 9 3 1 *
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising