Integra | DTR-5.8 | Owner Manual | Integra DTR-5.8 Receiver Owner Manual

Integra DTR-5.8 Receiver Owner Manual
AV Receiver
DTR-5.8
Instruction Manual
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, PORTABLE CART WARNING
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
S3125A
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and follow local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a fluelike gap for warm air to escape.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
the dealer from whom you purchased this unit.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
Setting the [Standby/On] switch to Standby does
not fully shutdown the unit. If you do not intend to
use the unit for an extended period, remove the
power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by the dealer from
whom you purchased this unit.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For Canadian models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
3
Thank you for purchasing an Integra AV Receiver.
Please read this manual thoroughly before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Supplied Accessories
Make sure you have the following accessories:
Remote controller & two batteries (AA/R6)
Speaker setup microphone
Indoor FM antenna
AM loop antenna
Power cord
(Plug type varies from country to country.)
Speaker cable labels
4
Surround Back
Right
Surround Back
Right
Zone 2
Right
Zone 2
Right
Surround Back
Right
Surround Back
Right
Zone 2
Right
Zone 2
Right
Center
Center
Surround Back
Left
Surround Back
Left
Zone 2
Left
Zone 2
Left
Center
Surround
Left
Surround
Left
Surround
Right
Surround
Right
Surround
Left
Surround
Left
Surround
Right
Surround
Right
2
3
Speaker Cable
Surround Back
Left
Surround Back
Left
Zone 2
Left
Zone 2
Left
Front
Right
Front
Right
SP-B / Zone 2
Right
SP-B / Zone 2
Right
Front
Right
Front
Right
SP-B / Zone 2
Right
SP-B / Zone 2
Right
1
Center
Front
Left
Front
Left
SP-B / Zone 2
Left
SP-B / Zone 2
Left
Front
Left
Front
Left
SP-B / Zone 2
Left
SP-B / Zone 2
Left
Speaker terminal tool
Table of Contents
Introduction
Important Safety Instructions ....................2
Precautions ..................................................3
Supplied Accessories..................................4
Features ........................................................6
Front & Rear Panels.....................................7
Front Panel..................................................... 7
Display............................................................ 9
Rear Panel ................................................... 10
Remote Controller......................................12
Installing the Batteries .................................. 12
Aiming the Remote Controller ...................... 12
Using the Remote Controller ........................ 13
Receiver/Tape Mode .................................... 13
DVD Mode.................................................... 15
CD/MD/CDR/Dock Mode.............................. 16
About Home Theater..................................17
Enjoying Home Theater................................ 17
Connections
Connecting the AV receiver ......................18
About AV Connections ................................. 18
Connecting Your Speakers .......................... 19
Bi-amping the Front Speakers...................... 21
Connecting Antenna..................................... 22
Connecting Both Audio & Video ................... 24
Which Connections Should I Use?............... 24
Connecting Your TV or Projector ................. 26
Connecting a DVD Player ............................ 27
Connecting a VCR or DVD Recorder for
Playback .................................................... 29
Connecting a VCR or DVD Recorder for
Recording................................................... 30
Connecting a Satellite, Cable, Set-top box, or
Other Video Source ................................... 31
Connecting a Game Console ....................... 32
Connecting a Camcorder or Other Device ... 33
Connecting Components with HDMI ............ 34
Connecting a CD Player or Turntable .......... 36
Connecting an RI Dock ................................ 37
Connecting a Cassette, CDR, MiniDisc,
or DAT Recorder........................................ 38
Connecting a Power Amplifier ...................... 38
Connecting
Components....................... 39
Connecting the RS232 Port.......................... 39
Connecting the Power Cord ......................... 39
Turning On the AV Receiver .....................40
Connecting the Power Cord ......................... 40
Turning On and Standby .............................. 40
First Time Setup
First Time Setup .........................................41
Automatic Speaker Setup (Audyssey 2EQ)..... 41
About the Onscreen Setup Menus ............... 46
HDMI Monitor ............................................... 47
Video Input Setup......................................... 48
Digital Input Setup ........................................ 50
Changing the Input Display .......................... 51
Speaker Settings .......................................... 51
TV Format Setup
(not North American model)....................... 52
AM Frequency Step Setup (Australian model) .... 53
Basic Operations
Basic Operations ....................................... 54
Selecting the Input Source ...........................54
Using the Multichannel DVD Input................55
Adjusting the Bass & Treble .........................55
Displaying Source Information......................55
Setting the Display Brightness......................56
Muting the AV receiver .................................56
Using the Sleep Timer ..................................56
Using Headphones .......................................56
Listening to the Radio............................... 57
Using the Tuner ............................................57
Presetting AM/FM Stations...........................58
Using the Listening Modes....................... 59
Selecting Listening Modes............................59
Listening Modes Available for Each Source
Format........................................................60
About the Listening Modes ...........................64
Recording................................................... 66
Advanced Operations
Advanced Operations ............................... 67
Using the Late Night Function (Dolby Digital,
Dolby Digital Plus, and Dolby TrueHD only) .....67
Using the CinemaFILTER.............................67
Adjusting Individual Speaker Levels.............67
Advanced Setup ........................................ 68
Speaker Setup..............................................68
Multichannel DVD Input Settings..................73
Audio Adjust Functions.................................74
Assigning Listening Modes to Input Sources.......76
Source Setup................................................77
Volume Setup/OSD Setup............................79
Changing the AV receiver’s ID .....................81
HDMI Setup ..................................................81
Lock Setup....................................................83
Digital Input Signal Formats .........................83
Changing the Remote Controller’s ID...........83
Zone 2 ......................................................... 84
Connecting Zone 2 .......................................84
Setting the Powered Zone 2 .........................84
Setting the Zone 2 Out .................................85
Using Zone 2 ................................................86
Using the 12V Triggers in Zone 2
and the Main Room....................................88
Using the Remote Controller in Zone 2
and Multiroom Control Kits.........................89
Controlling Other Components................ 90
Entering Remote Control Codes...................90
Remote Control Codes for Integra
Components Connected via
................91
Resetting Remote Mode Buttons..................91
Resetting the Remote Controller ..................91
Others
Specifications ............................................ 93
Troubleshooting ........................................ 94
5
Features
Amplification
• 90 watts minimum continuous power per channel, 8
ohm loads, 2 channels driven from 20 Hz to 20 kHz
with a maximum total harmonic distortion of 0.08 %
(FTC rating)
• WRAT-Wide Range Amplifier Technology
• Optimum Gain Volume Circuitry
*1.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are registered
trademarks of Dolby Laboratories.
*2.
“DTS” is a registered trademark of DTS, Inc. and “DTS-HD
Master Audio” is a trademark of DTS, Inc.
Processing
• HDMI and Component Video Upconversion
• Dolby*1 Digital Plus, Dolby TrueHD
• DTS*2-HD High Resolution Audio, DTS-HD Master
Audio
• Faroudja DCDi Edge Enhancement
• Neural Surround*3 Decoder (North American model
only)
• CinemaFILTER*4
• Non-Scaling Configuration
• A-Form Listening Mode Memory
• 192 kHz/24-bit D/A Converters
• Powerful and Highly Accurate 32-bit DSP Processing
Connections
•
•
•
•
•
•
•
•
2 HDMI*5 Inputs and 1 Output (ver. 1.3a)
5 Digital Inputs (3 Optical / 2 Coaxial 4 Assignable)
5 S-Video Inputs / 2 Output
Color-Coded Banana Plug Speaker Posts
Color-Coded 7.1 Multichannel Inputs
Subwoofer Pre Out
Powered Zone 2
Bi-Amp Connectable for FL/FR with SBL/SBR
“DTS” and “DTS-ES | Neo: 6” are registered trademarks of
DTS, Inc. “96/24” is a trademark of DTS, Inc.
*3.
Neural Surround name and related logos are trademarks owned
by Neural Audio Corporation.
*4.
“CinemaFILTER” is a trademark of Onkyo Corporation.
*5.
HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
*6.
©2005 SIRIUS Satellite Radio Inc. “SIRIUS,” the SIRIUS dog
logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Available only in the contiguous United States
(excluding Alaska and Hawaii) and Canada.
*7.
XM Ready® is a registered trademark of XM Satellite Radio
Inc. All rights reserved.
*8.
Miscellaneous
• SIRIUS Ready*6 / XM Ready*7 with XMHD Surround (North American model only)
• 40 SIRIUS/XM/AM/FM Presets (North American
model)
• 40 AM/FM Presets (Australian model)
• Audyssey*8 2EQ to Correct Room Acoustic Problems
• Crossover Adjustment
(40/45/50/55/60/70/80/90/100/120/130/150/200 Hz)
• A/V Sync Control Function (up to 100 ms)
• New Graphic On-Screen Display
• Compatible with RI Dock for iPod
• Aluminum Front Panel
• Preprogrammed RI-Compatible Remote
6
*
*
*
Manufactured under license from Audyssey Laboratories. U.S.
and foreign patents pending. 2EQ is a trademark of Audyssey
Laboratories.
Apple and iPod are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
“Xantech” is a registered trademark of Xantech Corporation.
“Niles” is a registered trademark of Niles Audio Corporation.
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited
consumer uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
Front & Rear Panels
Front Panel
North American model
1
2 3 4
bq br bs
5 6 7 8 9 bk bl bm bn bo
bt
ck
cl
bp
cm
Australian model
2 cn 3
The page numbers in parentheses show where you can find the main explanation for each item.
Standby/On button (40)
Stereo button (59)
This button is used to set the AV receiver to Standby
This button is used to select the Stereo listening
or On.
mode.
Standby indicator (40)
This indicator lights up when the AV receiver is in
Standby mode, and it flashes while a signal is being
received from the remote controller.
Zone 2 indicator (86)
This indicator lights up when Zone 2 is selected.
Remote control sensor (12)
This sensor receives control signals from the remote
controller.
Listening Mode [ ] [ ] buttons (59)
These buttons are used to select the listening modes.
Display
See “Display” on page 9.
Dimmer button (56)
Dimmer is used to adjust the display brightness.
Memory button (58)
This button is used when storing or deleting radio
presets.
7
Front & Rear Panels—Continued
(1 Tuning Mode button (57)
This button is used to select the Auto or Manual
tuning mode.
(2 Display button (55)
This button is used to display various information
about the currently selected input source.
(3 Setup button
This button is used to access the onscreen setup
menus that appear on the connected TV.
(4 Arrow/Tuning/Preset & Enter buttons
When the AM or FM input source is selected, the
Tuning [ ] [ ] buttons are used to tune the tuner,
and the Preset [ ] [ ] buttons are used to select
radio presets (see page 58). When the onscreen
setup menus are used, they work as arrow buttons
and are used to select and set items. The [Enter] button is also used with the onscreen setup menus.
(5 Return button
This button is used to return to the previously displayed onscreen setup menu.
(6 Master Volume control (54)
This control is used to adjust the volume of the AV
receiver to MIN, 1 through 99, or MAX.
(7 Zone 2/Off buttons (86)
The Zone 2 button is used to select the input source
for Zone 2.
The Off button is used to turn off the output of
Zone 2.
(8 Phones jack (56)
This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.
(9 Zone 2 Level button (87)
This button is used to set the volume for Zone 2.
(: Tone, [–] & [+] buttons (55)
These buttons are used to adjust the bass and treble.
)1 Input selector buttons (54)
These buttons are used to select from the following
input sources: Multi CH, DVD, VCR/DVR,
CBL/SAT, Game/TV, AUX, Tape, Tuner, or CD.
The [Multi CH] button selects the DVD analog multichannel input.
)2 Setup Mic (41)
The included speaker setup microphone is connected here for automatic speaker setup.
)3 AUX Input
This input can be used to connect a camcorder,
game console, and so on. There are jacks for optical
digital audio, S-Video, composite video, and analog
audio.
8
)4 Ready indicator (82) (Australian model)
Enters Ready mode and lights up when the HDMI
Power Control is set to Enable and the AV receiver
is on Standby.
Front & Rear Panels—Continued
Display
1 2
3
4
6
5
7
The page numbers in parentheses show where you can find the main explanation for each item.
SLEEP indicator (56)
This indicator lights up when the Sleep function has
been set.
MUTING indicator (56)
This indicator flashes or lights up while the AV
receiver is muted.
HDMI indicator
This indicator lights up when the HDMI audio signal input is used.
Listening mode & format indicators
These indicators show the currently selected listening mode and the format of digital input signals.
Tuning indicators
FM STEREO (57): This indicator lights up when
the AV receiver is tuned to a stereo FM station.
AUTO (57): This indicator lights up when the Auto
Tuning mode is selected, and disappears when the
Manual Tuning mode is selected.
TUNED (57): This indicator lights up when the AV
receiver is tuned into a radio station.
Message area
This area of the display shows various information
about the currently selected source.
Audyssey indicator (41, 72)
This indicator flashes during automatic speaker
setup and stays on when the setup is complete. It
also lights up when the Equalizer Settings are set to
Audyssey.
9
Front & Rear Panels—Continued
Rear Panel
North American model
(North American model only)
1
2
34
56
7 8 9 bk
bq br bs bt ckclcm cn
co
blbmbn
bo
bp
cp
The page numbers in parentheses show where you can find the main explanation for each item.
DIGITAL OPTICAL IN 1, 2 and OUT
FM ANTENNA (22)
These optical digital audio inputs are for connecting
This jack is for connecting an FM antenna.
components with optical digital audio outputs, such
MONITOR OUT
as CD players and DVD players.
The S-Video or composite video jack should be
The optical digital audio output is for connecting a
connected to a video input on your TV or projector.
digital recorder with an optical digital input, such as
IR IN A/B and OUT
a CD recorder.
A commercially available IR receiver can be con DIGITAL COAXIAL IN 1, 2
nected to the IR IN A or B jack, allowing you to
These coaxial digital audio inputs are for connectcontrol the AV receiver while you’re in Zone 2, or
ing components with coaxial digital audio outputs,
control it when it’s out of sight, for example,
such as CD players and DVD players.
installed in a cabinet.
XM antenna (North American model only)
A commercially available IR emitter can be conThis jack is for connecting an XM Minituner and
nected to the IR OUT jack to pass IR (infrared)
Home Dock, sold separately (see the separate XM
remote control signals along to other components.
instructions).
(1 12V TRIGGER OUT (A/B/C)
SIRIUS antenna (North American model
These outputs can be connected to the 12-volt trigonly)
ger inputs on other components.
This jack is for connecting a SIRIUS Satellite Radio
(2 RS232
antenna (see the separate SIRIUS instructions).
This port is for connecting the AV receiver to home
HDMI IN 1, 2, and OUT
automation equipment and external controllers.
HDMI (High Definition Multimedia Interface) con(3 FRONT, CENTER, SURR & SURR BACK
nections carry digital audio and digital video.
SPEAKERS (20)
The HDMI inputs are for connecting components
These terminal posts are for connecting your front,
with HDMI outputs, such as DVD players.
center, surround, and surround back speakers.
The HDMI output is for connecting a TV or projec(4 ZONE 2 PRE OUT (84)
tor with an HDMI input.
This analog audio output can be connected to a line
AM ANTENNA (22)
These push terminals are for connecting an AM
antenna.
10
input on an integrated amplifier in Zone 2.
(5 ZONE 2 SPEAKERS (84)
These terminals are for connecting speakers in
Zone 2.
Front & Rear Panels—Continued
(6 AC INLET
This connector is for connecting the supplied power
cord.
(7
REMOTE CONTROL
This
(Remote Interactive) jack can be connected to an
jack on another
-capable Integra component. The AV receiver’s remote controller
can then be used to control that component. To use
, you must make an analog audio connection
(RCA) between the AV receiver and the other AV
component, even if they are connected digitally.
(8 COMPONENT VIDEO IN 1, 2, 3
These component video inputs can be used to connect AV components with component video outputs,
such as DVD players.
(9 CD IN
This analog audio input is for connecting a CD
player’s analog audio output.
(: TAPE IN/OUT
This analog audio input and output are for connecting a recorder with an analog audio input and output
(cassette, Mini Disc, etc.).
)1 GAME/TV IN
Here you can connect a game console, TV, etc.
Input jacks include S-Video, composite video, and
analog audio.
)2 COMPONENT VIDEO OUT
This component video output can be used to connect a TV or projector with a component video
input.
)3 CBL/SAT IN
Here you can connect a cable/satellite receiver, settop box, etc. Input jacks include S-Video, composite
video, and analog audio.
)4 VCR/DVR IN/OUT
Here you can connect a VCR or DVR (digital video
recorder). Input and output jacks include S-Video,
composite video, and analog audio.
)5 DVD IN
Here you can connect a DVD player. Input jacks
include S-Video, composite video, and analog
audio. You can connect a DVD player’s 2-channel
analog audio output or 7.1-channel analog audio
output.
)6 FRONT, CENTER, SURR, and SURR BACK
SPEAKERS
These terminal posts are for connecting the front
L/R, center, surround L/R, and surround back L/R
speakers.
See pages 18-39 for connection information.
11
Remote Controller
Installing the Batteries
1
To open the battery compartment, press
the small hollow and slide off the cover.
Aiming the Remote Controller
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
Remote control sensor
AV receiver
Standby indicator
2
3
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
Put the cover onto the remote controller
and slide it shut.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.
12
Approx. 16 ft.
(5 m)
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in
mind when installing.
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote controller may not work reliably.
• Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an
obstacle between it and the AV receiver’s remote control sensor.
Remote Controller—Continued
Using the Remote Controller
The remote controller can be used to control different
components including the AV receiver. The remote controller has a specific operating mode for use with each
type of component. Modes are selected by using the six
Remote Mode buttons.
Receiver/Tape Mode
Receiver/Tape mode is used to control the AV receiver.
It can also be used to control an Integra cassette recorder
connected via
.
1
■ Receiver/Tape Mode
In Receiver/Tape mode, you can control the
AV receiver and an Integra cassette recorder
connected via
.
■ DVD and CD/MD/CDR/Dock Modes
With these modes, you can control a DVD
player and CD Player, MD recorder, CDR,
or RI dock. By entering the appropriate
remote control code, you can control components made by other manufacturers (see
page 90).
■ TV, VCR and SAT/Cable Modes
With these modes, you can control a TV,
VCR, and satellite or cable receiver. You
must enter the appropriate remote control
code first (see page 90).
2
3
4
bl
5
bm
1
2
bn
bo
36
1
7
Press one of the Remote Mode
buttons to select a mode.
bp
4
8
9
bk
2
Use the buttons supported by
that mode to control the component.
Receiver/Tape mode:
see right column
DVD mode:
see page 15
CD/MD/CDR/Dock mode:
see page 16
bq
br
Buttons , , , and are used when the Tuner or
Tape input is selected.
TV, VCR, SAT/Cable modes:
see page 92
Note:
Some of the remote controller operations described in
this manual may not work as expected with other components.
13
Remote Controller—Continued
For detailed information, see the pages in parentheses.
(8 L Night button (67)
Used with the Late Night function.
Zone 2 button (86)
Used to select the input source for Zone 2.
Standby/On button (40)
Sets the AV receiver to Standby or On.
Input Selector buttons (54)
■ Buttons used when the Tuner input is
selected
To select the Tuner (AM/FM) as the input
source, press:
Used to select the input sources.
Multi CH button (55)
Selects the multichannel DVD input.
Dimmer button (56)
Adjusts the display brightness.
Number, D TUN, and ENT buttons (57)
Used to select AM and FM radio stations directly.
Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons
Used to select and adjust settings.
CH +/– button (58)
Setup button
Used to access the setup menus.
Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons
Listening Mode buttons (59)
Used to select the listening modes. These buttons
work in all remote controller modes.
Stereo button
Selects the Stereo listening mode.
Surround button
Selects the Dolby and DTS listening modes and the
Neural Surround listening mode (North American
models only).
Used to select radio presets.
For AM and FM, the Up and Down [
tons are used for tuning.
]/[
] but-
■ Buttons used when the Tape input is
selected
To select your Cassette deck as the input
source, press:
[ ]/[ ] buttons
Used to select the available listening modes.
Test Tone, CH SEL, Level-, and Level+
buttons (67, 71)
Used to adjust the level of each speaker.
(1 Display button (55)
Displays various information about the selected
input source.
(2 Remote Mode buttons (13)
Used to select the remote controller modes. When a
remote controller button is pressed, the Remote
Mode button for the currently selected mode lights
up.
(3 Sleep button (56)
Used with the Sleep function.
(4 VOL [ ]/[ ] button (54)
Adjusts the volume of the AV receiver regardless of
the currently selected remote controller mode.
(5 Muting button (56)
Mutes or unmutes the AV receiver.
(6 Return button
Selects the previously displayed setup menu.
(7 CINE FLTR button (67)
Used with the CinemaFILTER function.
14
Playback buttons
On twin cassette decks, only deck B can be controlled.
Play [ ] button
Starts playback.
Stop [ ] button
Stops playback.
Reverse Play [ ] button
Starts reverse playback.
Rewind and FF [ ]/[ ] buttons
The Rewind [ ] button starts rewind. The FF
[ ] button starts fast forward.
Remote Controller—Continued
Standby/On button
DVD Mode
Sets the DVD player to Standby or On.
By default, the remote controller is set to control an Integra DVD player.
To select your DVD player as the input source, press:
Number buttons
Used to enter title, chapter, and track numbers and
times for locating specific points.
Disc +/– button
or
Selects discs on a DVD changer.
Top Menu button
Selects a DVD’s top menu.
Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons
Used to navigate DVD menus and the DVD player’s
onscreen setup menus.
Setup button
Used to access the DVD player’s onscreen setup
menus.
1
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous, and Next.
2
Subtitle button
Selects subtitles.
bl
Audio button
Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).
(1 Display button
3
4
bm
5
6
(2 CLR button
Cancels functions and clears entered numbers.
(3 Menu button
bn
Displays a DVD’s menu.
(4 Return button
Exits the DVD player’s onscreen setup menus.
7
8
9
bk
Displays information about the current disc, title,
chapter, or track, including elapsed time, remaining
time, total time, and so on.
(5 Random button
Used with the random playback function.
bo
bp
bq
br
(6 Repeat button
Used with the repeat playback functions.
(7 VCR, DVD, and HDD buttons
Used to select VCR, HDD (hard disk drive), or
DVD playback on a VCR/DVD recorder with a
built-in hard disk drive.
(8 Play Mode button
Selects play modes on components with selectable
play modes.
15
Remote Controller—Continued
Standby/On button
CD/MD/CDR/Dock Mode
Sets the component to Standby or On.
By default, the remote controller is set to control an Integra CD player.
To select the input source, press:
Number buttons
Used to enter track numbers and times for locating
specific points on CD/MD players.
Disc/Album +/– button
CD player
MD or CD recorder
Selects discs on a CD changer, or the next or previous album on an HDD-compatible component connected to an RI Dock.
Top Menu button
or
Works as a Mode button when used with a DS-A2
RI Dock.
RI Dock
* If you’re using an MD, CDR, or RI Dock, you must
change the input display (see page 51).
Display button
Displays information about the current disc or track
on a CD player or MD/CD recorder, including
elapsed time, remaining time, total time, and so on.
On an HDD-compatible component connected to an
RI Dock, it turns on the back light for 30 seconds.
2
4
5
Used to navigate menus on an HDD-compatible
component connected to an RI Dock.
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous and Next.
1
3
Arrow [ ]/[ ] and Enter buttons
8
9
bk
CLR button
Cancels functions and clears entered numbers on a
CD player or MD/CD recorder.
Menu button
Used to navigate menus on an HDD-compatible
component connected to an RI Dock.
(1 Playlist [ ]/[ ] buttons
Selects the previous or next playlist on an HDDcompatible component connected to an RI Dock.
(2 Random button
Used with the random/shuffle playback function.
(3 Repeat button
Used with the repeat playback functions.
6
(4 Play Mode button
bl
bm
7
16
bn
Used to select play modes on components with
selectable play modes.
Works as a Resume button when used with a DS-A2
RI Dock.
About Home Theater
Enjoying Home Theater
Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your
own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With
analog and digital TV you can enjoy Dolby Pro Logic IIx or Onkyo’s own DSP surround listening modes.
Front left and right speakers
These output the overall sound. Their role in a home theater is to provide a solid
anchor for the sound image. They should be positioned facing the listener at about
ear level, and equidistant from the TV. Angle them inward so as to create a triangle,
with the listener at the apex.
Surround back left and right
speakers
These speakers are necessary to
enjoy Dolby Digital EX, DTS-ES
Matrix, and DTS-ES Discrete. They
enhance the realism of surround
sound and improve sound localization behind the listener. Position
them behind the listener about 2–
3 feet (60–100 cm) above ear level.
Center speaker
This speaker enhances the
front left and right speakers,
making sound movements distinct and providing a full sound
image. In movies it’s used
mainly for dialog.
Position it close to your TV facing forward at about ear level, or
at the same height as the front
left and right speakers.
Corner
Subwoofer
The subwoofer handles the bass sounds
of the LFE (Low-Frequency Effects)
channel. The volume and quality of the
bass output from your subwoofer will
depend on its position, the shape of your
listening room, and your listening position. In general, a good bass sound can
be obtained by installing the subwoofer in
a front corner, or at one-third the width of
the wall, as shown.
Tip: To find the best position for your subwoofer, while playing a movie or some
music with good bass, experiment by
placing your subwoofer at various positions within the room, and choose the one
that provides the most satisfying results.
1/3 wall
length
Surround left and right speakers
These speakers are used for precise sound positioning and
to add realistic ambience.
Position them at the sides of the listener, or slightly behind,
about 2–3 feet (60–100 cm) above ear level. Ideally they
should be equidistant from the listener.
17
Connecting the AV receiver
AV Connection Color Coding
About AV Connections
• Before making any AV connections, read the manuals
supplied with your other AV components.
• Don’t connect the power cord until you’ve completed
and double-checked all AV connections.
Optical Digital Jacks
The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and
close when it’s removed. Push plugs in all the way.
RCA-type AV connections are usually color-coded: red,
white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”).
Use white plugs to connect left-channel audio inputs and
outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
Left (white)
Analog audio
Left (white)
Right (red)
Right (red)
Composite video
(Yellow)
(Yellow)
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
• Push plugs in all the way to make
good connections (loose connections can cause noise or malfunctions).
• To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
Right!
Wrong!
AV Cables & Jacks
Video
Cable
Jack
Description
Component
video cable
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality (some TV manufacturers label their
component video sockets slightly differently).
S-Video cable
S-Video separates the luminance and color signals
and provides better picture quality than composite
video.
Composite
video cable
V
Composite video is commonly used on TVs, VCRs,
and other video equipment. Use only dedicated
composite video cables.
Audio
Cable
Jack
Optical digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for coaxial.
Coaxial digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for optical.
Analog audio
cable (RCA)
L
R
Multichannel
analog audio
cable (RCA)
Note: The AV receiver does not support SCART plugs.
18
Description
This cable carries analog audio. It’s the most
common connection format for analog audio, and
can be found on virtually all AV components.
This cable carries multichannel analog audio and
it’s typically used to connect DVD players with a
7.1-channel analog audio output. Several standard
analog audio cables can be used instead of a multichannel cable.
Connecting the AV receiver—Continued
Connecting a Powered Subwoofer
Connecting Your Speakers
Speaker Configuration
For the best surround sound experience, you should connect seven speakers and a powered subwoofer.
The following table indicates the channels you should
use depending on the number of speakers that you have.
Number of speakers:
2
3
4
5
6
7
Front left
✓
✓
✓
✓
✓
✓
Front right
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Center
Surround left
✓
✓
✓
✓
Surround right
✓
✓
✓
✓
Using a suitable cable, connect the AV receiver’s PRE
OUT SUBWOOFER to an input on your powered subwoofer, as shown. If your subwoofer is unpowered and
you’re using an external amplifier, connect the PRE
OUT SUBWOOFER to an input on the amp.
Powered
subwoofer
LINE INPUT
LINE INPUT
✓
Surround back*
Surround back left
✓
Surround back right
✓
*If you’re using only one surround back speaker, connect it to
the left (L) SURR BACK SPEAKERS terminals.
No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid
bass.
To get the best from your surround sound system, you
need to set the speaker settings by using the supplied
speaker setup microphone (see page 41).
Using Dipole Speakers
You can use dipole speakers for the surround left and
right and surround back left and right speakers. Dipole
speakers output the same sound in two directions.
Dipole speakers typically have an arrow printed on them to
indicate how they should be positioned. The surround left
and right dipole speakers should be positioned so that their
arrows point toward the TV/screen, while the surround
back left and right dipole speakers should be positioned so
that their arrows point toward each other, as shown.
2
1
5
8
1. Subwoofer
2. Front left speaker
3. Center speaker
4. Front right speaker
5. Surround left speaker
4
3
2
6
7
Speaker terminal
Color
Front left, Zone 2 left
White
Front right, Zone 2 right
Red
Center
Green
Surround left
Blue
Surround right
Gray
Surround back left
Brown
Surround back right
Tan
The supplied speaker labels are also color-coded and you
should attach them to the positive (+) side of each
speaker cable in accordance with the above table. Then
all you need to do is to match the color of each label to
the corresponding speaker terminal.
1
TV/screen
4
3
The AV receiver’s positive (+) speaker terminals are
color-coded for ease of identification (the negative (–)
speaker terminals are all black).
Normal speakers
Dipole speakers
TV/screen
Attaching the Speaker Labels
5
Using the Speaker Terminal Tool
6
7
The supplied speaker terminal tool makes it easy to
tighten and loosen the speaker terminals. If you are using
banana plugs, to ensure optimum sound quality, tighten
the speaker terminal before inserting the banana plug.
(In Europe, using banana plugs to connect speakers to an
audio amplifier is prohibited.)
8
6. Surround right speaker
7. Surround back left
speaker
8. Surround back right
speaker
19
Connecting the AV receiver—Continued
Speaker Connection Precautions
Read the following before connecting your speakers:
• North American models: Only connect speakers
with an impedance of 6 ohms or higher. If you use
speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the
built-in protection circuit may be activated.
• Other models: You can connect speakers with an
impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or
more, but less than 6 ohms, be sure to set the minimum
speaker impedance to “4 ohms” (see page 51). If you
use speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in protection circuit may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• If you use 4 or 5 speakers, connect each of the two
surround speakers to the SURR SPEAKERS terminals. Do not connect them to the SURR BACK
SPEAKERS terminals.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
• Make sure the metal core of the
wire does not have contact with
the AV receiver’s rear panel.
Doing so may damage the AV
receiver.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
Connecting the Speaker Cables
1
Strip about 5/8" (15 mm)
of insulation from the
ends of the speaker
cables, and twist the bare
wires tightly, as shown.
2
Unscrew the terminal.
3
Fully insert the bare
wires.
4
Screw the terminal tight.
The following illustration shows which speaker should
be connected to each pair of terminals.
If you’re using only one surround back speaker, connect
it to the left (L) SURR BACK SPEAKERS terminals.
Surround Surround
back left back right
speaker speaker
Surround
left
speaker
Front right
speaker
20
15 mm
Surround
right
speaker
Front left
speaker
Center
speaker
Connecting the AV receiver—Continued
Bi-amping the Front Speakers
The FRONT L/R and SURR BACK L/R terminal posts
can be used with front speakers and surround back
speakers respectively, or bi-amped to provide separate
tweeter and woofer feeds for a pair of front speakers that
support bi-amping, providing improved bass and treble
performance.
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• For bi-amping, the FRONT L/R terminal posts connect to the front speakers’ tweeter terminals. And the
SURR BACK L/R terminal posts connect to the front
speakers’ woofer terminals.
• Once you’ve completed the bi-amping connections
shown below and turned on the AV receiver, you must
set the Speaker Type setting to Bi-Amp to enable
biamping (see page 51).
Important:
• When making the bi-amping connections, be sure
to remove the jumper bars that link the speakers’
tweeter (high) and woofer (low) terminals.
Bi-amping Speaker Hookup
1
Connect the AV receiver’s FRONT R positive (+)
terminal to the right speaker’s positive (+) tweeter
(high) terminal. And connect the AV receiver’s
FRONT R negative (–) terminal to the right
speaker’s negative (–) tweeter (high) terminal.
2
Connect the AV receiver’s SURR BACK R positive (+) terminal to the right speaker’s positive (+)
woofer (low) terminal. And connect the AV
receiver’s SURR BACK R negative (–) terminal
to the right speaker’s negative (–) woofer (low)
terminal.
3
Connect the AV receiver’s FRONT L positive (+)
terminal to the left speaker’s positive (+) tweeter
(high) terminal. And connect the AV receiver’s
FRONT L negative (–) terminal to the left
speaker’s negative (–) tweeter (high) terminal.
4
Connect the AV receiver’s SURR BACK L positive (+) terminal to the left speaker’s positive (+)
woofer (low) terminal. And connect the AV
receiver’s SURR BACK L negative (–) terminal to
the left speaker’s negative (–) woofer (low) terminal.
Low range
(Woofer)
High range
(Tweeter)
Right speaker
Left speaker
21
Connecting the AV receiver—Continued
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The AV receiver won’t pick up any radio signals without
any antenna connected, so you must connect the antenna
to use the tuner.
AM antenna push terminals
FM antenna connector
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
1
Attach the FM antenna, as shown.
■ North American models
FM 75
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 23).
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
1
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around.)
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Insert the plug fully
into the jack.
■ Other models
Push
Insert wire
Release
FM 75
Insert the plug fully
into the jack.
Once your AV receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
2
Use thumbtacks or something similar to
fix the FM antenna into position.
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
22
Once your AV receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your AV receiver, TV, speaker cables, and power
cords.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 23).
Connecting the AV receiver—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
FM 75
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock hazards.
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To AV receiver
To TV (or VCR)
23
Connecting the AV receiver—Continued
Connecting Both Audio & Video
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you
can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver.
: Signal Flow
Video
Video
Audio
Audio
TV, projector,
etc.
DVD player, etc.
Speakers (see page 20 for connection information)
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
For video components, you must make two connections—one for audio, one for video.
Video Connection Formats
Video equipment can be connected to the AV receiver by using any one of the following video connection formats:
composite video, S-Video, component video, or HDMI, the latter offering the best picture quality.
The AV receiver can upconvert and downconvert between video formats, depending on the HDMI Monitor setting,
which generally determines whether video signals are upconverted for the component video output or the HDMI output.
■ HDMI Monitor Setting Set to Yes
With the HDMI Monitor setting set to Yes (see
page 47), video input signals flow through the
AV receiver as shown, with composite video,
S-Video, and component video sources all being
upconverted for the HDMI output. Use this setting if you connect the AV receiver’s HDMI OUT
to your TV.
The composite video, S-Video, and component
video outputs pass through their respective input
signals as they are.
DVD player, etc.
Video Signal Flow Chart
Composite
Component
HDMI
IN
AV receiver
MONITOR OUT
Composite
TV, projector, etc.
24
S-Video
S-Video
Component
HDMI
Connecting the AV receiver—Continued
■ HDMI Monitor Setting Set to No
With the HDMI Monitor setting set to No (see
page 47), video input signals flow through the
AV receiver as shown, with composite video and
S-Video sources being upconverted for the component video output. Use this setting if you connect the AV receiver’s COMPONENT VIDEO
OUT to your TV.
Composite video is upconverted to S-Video and
S-Video is downconverted to composite video.
Note that these conversions only apply to the
MONITOR OUT V and S outputs, not the
VCR/DVR OUT V and S outputs.
The composite video, S-Video, and component
video outputs pass through their respective input
signals as they are.
DVD player, etc.
Video Signal Flow Chart
Composite
S-Video
Component
HDMI
IN
AV receiver
MONITOR OUT
Composite
Component
S-Video
HDMI
TV, projector, etc.
Audio Connection Formats
Audio equipment can be connected to the AV
receiver by using any of the following audio connection formats: analog, optical, coaxial, analog
multichannel, or HDMI.
When choosing a connection format, bear in
mind that the AV receiver does not convert digital
input signals for analog line outputs and vice
versa. For example, audio signals connected to
an optical or coaxial digital input are not output
by the analog TAPE OUT.
DVD player, etc.
Audio Signal Flow Chart
Analog Multichannel Optical
Coaxial
HDMI
IN
AV receiver
OUT
Analog
Optical
HDMI
MD recorder, etc.
25
Connecting the AV receiver—Continued
Connecting Your TV or Projector
Step 1: Video Connection
Choose a video connection that matches your TV ( A , B , or C ), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection.
• With connection a , you can listen to and record audio from your TV and listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (For recording, use a and b , or a and c .)
Connection
AV receiver
Signal flow
TV
A
COMPONENT VIDEO OUT
Component video input
Best
B
MONITOR OUT S
S-Video input
Better
C
MONITOR OUT V
Composite video input
Standard
a
GAME/TV IN L/R
Ÿ
Ÿ
Ÿ



b
DIGITAL COAXIAL IN 2 (CBL/SAT)
c
DIGITAL OPTICAL IN 1 (GAME/TV)
Picture quality
Analog audio L/R output
Digital coaxial output
Digital optical output
b
C
c
B
a
A
L
COAXIAL
OUT
OPTICAL
OUT
Connect one or the other
Connection b must be assigned (see page 50)
Hint!
26
Y
PB
PR
COMPONENT VIDEO IN
R
AUDIO
OUT
S VIDEO
IN
VIDEO
IN
TV, projector,
etc.
If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver
to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 29 and
31).
Connecting the AV receiver—Continued
Connecting a DVD Player
Step 1: Video Connection
Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection.
You must connect the AV receiver to your TV via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection.
• With connection a , you can listen to and record audio from a DVD and listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (For recording, use a and b , or a and c .)
• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the
main left and right outputs for connection a .
Connection
AV receiver
Signal flow
DVD player
Picture quality
A
COMPONENT VIDEO IN 1 (DVD)






Component video output
Best
B
DVD IN S
C
DVD IN V
a
DVD IN FRONT L/R
b
DIGITAL COAXIAL IN 1 (DVD)
c
DIGITAL OPTICAL IN 1 (GAME/TV)
S-Video output
Better
Composite video output
Standard
Analog audio L/R output
Digital coaxial output
Digital optical output
b
C
c
B
a
A
L
COAXIAL
OUT
OPTICAL
OUT
PR
Y
PB
COMPONENT VIDEO OUT
Connect one or the other
Connection c must be assigned (see page 50)
R
AUDIO
OUT
S VIDEO
OUT
VIDEO
OUT
DVD player
To connect a DVD player or DVD-Audio/SACD-capable player with a
multichannel analog audio output, see page 28.
27
Connecting the AV receiver—Continued
Hooking Up the Multichannel DVD Input
If your DVD player supports multichannel audio formats such as DVD-Audio or SACD, and it has a multichannel
analog audio output, you can connect it to the AV receiver’s multichannel DVD input.
Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT
L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on
your DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV
receiver’s SURR BACK L/R jacks.
7.1 ch
5.1 ch
FRONT
SURR
CENTER
SURR BACK
L
L
R
R
DVD
L
R
FRONT
L
SUB
WOOFER
R
SURROUND
L
CENTER
SUB
WOOFER
DVD player
28
R
SURR
BACK
Connecting the AV receiver—Continued
Connecting a VCR or DVD Recorder for Playback
Hint!
With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV
receiver, useful if your TV has no audio outputs.
Step 1: Video Connection
Choose a video connection that matches your VCR or DVD recorder ( A , B , or C ), and then make the connection.
You must connect the AV receiver to your TV via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVD recorder ( a , b , or c ), and then make the connection.
• With connection a , you can listen to the VCR or DVD recorder even in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (To listen in Zone 2 as well, use a and b , or a and
c .)
Connection
AV receiver
Signal flow
VCR or DVD recorder
Picture quality
A
COMPONENT VIDEO IN 2






Component video output
Best
B
VCR/DVR IN S
C
VCR/DVR IN V
a
VCR/DVR IN L/R
b
DIGITAL COAXIAL IN 2 (CBL/SAT)
c
DIGITAL OPTICAL IN 1 (GAME/TV)
S-Video output
Better
Composite video output
Standard
Analog audio L/R output
Digital coaxial output
Digital optical output
.
b
C
c
B
Connection
A must be
assigned
(see
page 49)
a
A
L
COAXIAL
OUT
OPTICAL
OUT
PR
Y
PB
COMPONENT VIDEO OUT
R
AUDIO
OUT
S VIDEO
OUT
VIDEO
OUT
Connect one or the other
Connection b must be assigned (see page 50)
VCR,
DVD recorder
29
Connecting the AV receiver—Continued
Connecting a VCR or DVD Recorder for Recording
Step 1: Video Connection
Choose a video connection that matches your VCR or DVD recorder ( A or B ), and then make the connection. The
video source to be recorded must be connected to the AV receiver via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVD recorder ( a or b ), and then make the connection.
Connection
AV receiver
Signal flow
VCR or DVD recorder
A
VCR/DVR OUT S
S-Video input
Better
B
VCR/DVR OUT V
Ÿ
Ÿ
Ÿ
Ÿ
Composite video input
Standard
a
VCR/DVR OUT L/R
b
DIGITAL OPTICAL OUT
Picture quality
Audio L/R input
Digital optical input
C
B
B
A
b
a
L
OPTICAL
IN
R
AUDIO
IN
S VIDEO
IN
VIDEO
IN
VCR,
DVD recorder
Notes:
• The AV receiver must be turned on for recording. Recording is not possible while it’s in Standby mode.
• If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV
receiver, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See
the manuals supplied with your TV and VCR for details.
• Video signals connected to composite video inputs can only be recorded via composite video outputs. If your
TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.
Similarly, video signals connected to S-Video inputs can only be recorded via S-Video outputs. If your TV/VCR is
connected to an S-Video input, the recording VCR must be connected to an S-Video output.
30
Connecting the AV receiver—Continued
Connecting a Satellite, Cable, Set-top box, or Other Video Source
Hint!
With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs
via the AV receiver, useful if your TV has no audio outputs.
Step 1: Video Connection
Choose a video connection that matches the video source ( A , B , or C ), and then make the connection.
You must connect the AV receiver to your TV via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches the video source ( a , b , or c ), and then make the connection.
• With connection a , you can listen to and record audio from the video source and listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b or c . (For recording, use a and b , or a and c .)
Connection
AV receiver
Signal flow
Video source
Picture quality
A
COMPONENT VIDEO IN 3






Component video output
Best
B
CBL/SAT IN S
C
CBL/SAT IN V
a
CBL/SAT IN L/R
b
DIGITAL COAXIAL IN 2 (CBL/SAT)
c
DIGITAL OPTICAL IN 1 (GAME/TV)
S-Video output
Better
Composite video output
Standard
Analog audio L/R output
Digital coaxial output
Digital optical output
b
C
c
B
Connection
A must be
assigned
(see
page 49)
a
A
L
COAXIAL
OUT
OPTICAL
OUT
PR
Y
PB
COMPONENT VIDEO OUT
R
AUDIO
OUT
S VIDEO
OUT
VIDEO
OUT
Connect one or the other
Connection b must be assigned (see page 50)
Satellite, cable, set-top box, etc.
31
Connecting the AV receiver—Continued
Connecting a Game Console
Step 1: Video Connection
Choose a video connection that matches the game console ( A , B , or C ), and then make the connection.
If you use connection A , you must connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches the DVD player ( a or b ), and then make the connection.
• With connection a , you can listen to and record audio from the game console or listen in Zone 2.
• To enjoy Dolby Digital and DTS, use connection b . (To record or listen in Zone 2 as well, use a and b .)
Connection
AV receiver
Signal flow
Game console
Picture quality
A
COMPONENT VIDEO IN 3





Component video output
Best
B
GAME/TV IN S
C
GAME/TV IN V
a
GAME/TV IN L/R
b
DIGITAL OPTICAL IN 1 (GAME/TV)
S-Video output
Better
Composite video output
Standard
Analog audio L/R output
Digital optical input
b
C
B
a
A
L
OPTICAL
OUT
PR
Y
PB
COMPONENT VIDEO OUT
R
AUDIO
OUT
S VIDEO
OUT
Game Console
32
VIDEO
OUT
Connecting the AV receiver—Continued
Connecting a Camcorder or Other Device
Step 1: Video Connection
Choose a video connection that matches the camcorder ( A or B ), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches the camcorder ( a or b ), and then make the connection.
B
Video
AUX Input
a
b
AUX Input
AUX Input
Digital
S Video
L – Audio – R
AUX Input
A
OPTICAL
OUT
S VIDEO
OUT
L AUDIO R
OUT
VIDEO
OUT
Camcorder, etc.
Connection
AV receiver
Signal flow
A
AUX Input S Video
B
AUX Input Video
a
AUX Input Audio L/R
b
AUX Input Digital




Camcorder or console
S-Video output
Composite video output
Analog audio L/R output
Digital optical output
33
Connecting the AV receiver—Continued
Connecting Components with HDMI
About HDMI
Designed to meet the demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface
standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several
separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry
control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, and
multichannel PCM).
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays
with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and
displays, resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital Content Protection), so only HDCP-compatible components can
display the picture.
The AV receiver’s HDMI interface is based on the following standard:
High-Definition Multimedia Interface Specification Informational Version 1.3a
Supported Audio Formats
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)
• Bitstream (Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD
Master Audio)
Your DVD player must also support HDMI output of the above audio formats.
About Copyright Protection
The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital
video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.
Commercially available HDMI cables (supplied with some components) should be used to connect the AV receiver’s
HDMI OUT to the HDMI input on your TV or projector.
*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999.
*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to
protect video content and requires a HDCP-compatible device to display the encrypted video.
*3 DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open
industry group’s objective is to address the industry's requirements for a digital connectivity specification for high-performance PCs and
digital displays.
34
Connecting the AV receiver—Continued
Making HDMI Connections
Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV,
projector, and so on.
Step 2: Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 48).
■ Video Signals
Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.
Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Connection Formats” on page 24 for more information.
■ Audio Signals
Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV
receiver. Normally, they are not output by the HDMI OUT, unless the HDMI Audio Out setting is set to On (see
page 82).
Note:
When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen
on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power
is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut
off.
Hint!
To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the HDMI Audio
Out setting to On (see page 82), and set your DVD player’s HDMI audio output setting to PCM.
HDMI
IN
HDMI
OUT
DVD player
TV
HDMI
HDMI
IN 1
35
Connecting the AV receiver—Continued
Connecting a CD Player or Turntable
■ CD Player or Turntable (MM) with Built-in Phono Preamp
Step 1:
Choose a connection that matches your CD player ( a , b , or c ). Use connection a for a turntable with a built-in
phono preamp.
b
COAXIAL
IN
IN 2
(CBL/SAT)
Connect one or
the other
Connection b
must be
assigned (see
page 50)
c
L
L
R
OPTICAL
R
AUDIO
OUTPUT
CD
IN 2
(CD)
IN
a
L
R
CD
COAXIAL
OUT
L
OPTICAL
OUT
a
R
AUDIO
OUT
Turntable (MM) with
built-in phono preamp
CD player
• With connection a , you can listen to and record audio from the CD player and listen in Zone 2.
• To connect the CD player digitally, use connection b or c . (For recording, use a and b , or a and c .)
Connection
AV receiver
Signal flow
CD or turntable
a
CD IN L/R
Analog audio L/R output
b
DIGITAL COAXIAL IN 2 (CBL/SAT)
c
DIGITAL OPTICAL IN 2 (CD)



■ Turntable (MM) with no Phono Preamp Built-in
A phono preamp is necessary to connect a turntable that
doesn’t have a phono preamp built-in.
IN
AUDIO
OUTPUT
L
L
R
Phono preamp
■ Turntable with an MC (Moving Coil) Cartridge
An MC head amp and phono preamp are necessary to
connect a turntable with an MC (Moving Coil) cartridge.
AUDIO
OUTPUT
L
L
R
R
CD
CD
36
Digital optical output
IN
R
AUDIO
OUTPUT
Digital coaxial output
AUDIO
INPUT
AUDIO
OUTPUT
L
L
R
R
Phono
preamp
MC head amp or
MC transformer
AUDIO
INPUT
L
L
R
R
AUDIO
OUTPUT
AUDIO
INPUT
L
L
R
R
Connecting the AV receiver—Continued
Connecting an RI Dock
■ RI Dock with video
Connect your RI Dock’s analog audio output jacks
and S-Video output jack to the AV receiver’s
GAME/TV IN L/R jacks and GAME/TV IN S jack.
(The example shown below is for connection with
the DS-A1.)
■ RI Dock without video
Connect your RI Dock’s analog audio output jacks to
the AV receiver’s TAPE IN L/R jacks.
AUDIO
OUT
S VIDEO
OUT
L
AUDIO
OUT
L
R
R
Notes:
• Connect the Remote Interactive Dock with an
cable (see page 39).
• Set the Remote Interactive Dock’s RI MODE switch to HDD or HDD/DOCK.
• Set the AV receiver’s input display to DOCK (see page 51).
• Refer to the Remote Interactive Dock’s instruction manual.
37
Connecting the AV receiver—Continued
Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
Step 1:
Choose a connection that matches the recorder ( a , b , c , or d ), and then make the connection.
b
c
IN
COAXIAL
L
IN 2
(CBL/SAT)
R
a
TAPE
OPTICAL
IN 1
(GAME/TV)
a
L
OPTICAL
DIGITAL OUT
R
TAPE
d
Connect one
or the other
L
COAXIAL
OUT
OPTICAL
OUT
R
LL
AUDIO
IN
OPTICAL
IN
RR
Cassette, CDR, MD, etc.
AUDIO
OUT
• With connection a , you can play and record and listen in Zone 2.
• To connect the recorder digitally for playback, use connections a and b , or a and c .
• To connect the recorder digitally for recording, use connection d .
d
Connection
AV receiver
Signal flow
Cassette, CDR, MD, or DAT recorder
a
TAPE IN L/R
TAPE OUT L/R
Analog audio L/R output
Analog audio L/R input
b
DIGITAL COAXIAL IN 2 (CBL/SAT)
c
DIGITAL OPTICAL IN 1 (GAME/TV)
d
DIGITAL OPTICAL OUT

Ÿ


Ÿ
Digital coaxial output
Digital optical output
Digital optical input
Connecting a Power Amplifier
If you want to use a more powerful power amplifier
and use the AV receiver as a preamp, connect it to
the PRE OUT jacks, and connect all speakers and
the subwoofer to the power amplifier. If you have a
powered subwoofer, connect it to this AV
receiver’s PRE OUT SUBWOOFER jack.
1. Subwoofer
2. Front left speaker
3. Center speaker
4. Front right speaker
5. Surround left speaker
6. Surround right
speaker
7. Surround back left
speaker
8. Surround back right
speaker
1
2
3
4
5
Power amplifier
38
6
7
8
Connecting the AV receiver—Continued
Connecting
Components
IN
L
R
Step 1: Make sure that each Integra component is
connected to the AV receiver with an analog
audio cable (connection a in the hookup
examples) (see pages 26 to 38).
Step 2: Make the
CD
FRONT
REMOTE
CONTROL
L
R
connection.
DVD
Step 3: If you’re using an MD, CDR, or RI Dock,
change the input display (see page 51).
e.g., CD player
R
L
ANALOG
AUDIO OUT
With
(Remote Interactive), you can use the following special functions:
■ Auto Power On/Standby
When you start playback on a component connected
via
, if the AV receiver is on Standby, it will automatically turn on and select that component as the
input source. Similarly, when the AV receiver is set
to Standby, all components connected via
will
also go on Standby.
■ Direct Change
When playback is started on a component connected
via
, the AV receiver automatically selects that
component as the input source. If your DVD player
is connected to the AV receiver’s multichannel DVD
input, you’ll need to press the [Multi CH] button to
hear all channels (see page 55), as the Direct Change
function only selects the FRONT DVD IN jacks.
■ Remote Control
You can use the AV receiver’s remote controller to
control your other
-capable Integra components,
pointing the remote controller at the AV receiver’s
remote control sensor instead of the component. You
must enter the appropriate remote control code first
(see page 91).
Notes:
• Use only
cables for
connections.
cables
are supplied with Integra players (DVD, CD, etc.).
• Some components have two
jacks. You can connect either one to the AV receiver. The other jack is for
connecting additional
-capable components.
• Connect only Integra components to
jacks. Connecting other manufacturer’s components may cause a
malfunction.
• Some components may not support all
functions.
Refer to the manuals supplied with your other Integra
components.
• If you connect an Integra MD recorder, CD recorder,
or an Onkyo RI DOCK, you must change the input
display (see page 51).
e.g., DVD player
R
L
ANALOG
AUDIO OUT
Connecting the RS232 Port
This port is for connecting the AV receiver to home automation equipment and external controllers.
Connecting the Power Cord
Notes:
• Before connecting the power cord, connect all of your
speakers and AV components.
• Turning on the AV receiver may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the AV receiver into a different branch circuit.
• Do not use a power cord other than the one supplied
with the AV receiver. The supplied power cord is
designed exclusively for use with the AV receiver and
should not be used with any other equipment.
• Never disconnect the power cord from the AV receiver
while the other end is still plugged into a wall outlet.
Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then
the AV receiver.
To AC wall outlet
1
Connect the supplied power cord to the
AV receiver’s AC INLET.
2
Plug the power cord into an AC wall outlet.
The Standby indicator lights up.
39
Turning On the AV Receiver
Receiver
Standby/On
Standby indicator
Standby/On
Connecting the Power Cord
• Connect the AV receiver’s power cord to a suitable wall outlet.
Notes:
• Before connecting the power cord, connect all of your speakers and AV components.
• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
Turning On and Standby
1
AV receiver
Remote
controller
or
Press the [Standby/On] button.
Alternatively, press the remote controller’s [Receiver] button, followed by
the [Standby/On] button.
The AV receiver comes on, the display lights up, and the Standby indicator goes off.
To turn the AV receiver off, press the [Standby/On] button, or press the remote controller’s [Standby/On] button. The AV receiver will enter Standby mode. To prevent any
loud surprises when you turn on the AV receiver, always turn down the volume before
you turn it off.
Smooth Operation in a Few Easy Steps
To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the
very first time. These settings only need to be made once.
■ Do the automatic speaker setup—this is essential!
See “Automatic Speaker Setup (Audyssey 2EQ)” on page 41.
■ Have you connected a component to an HDMI input,
component video input, or digital audio input?
If you have, see “HDMI Input Setup” on page 48, “Component Video
Setup” on page 49, or “Digital Input Setup” on page 50 respectively.
■ Have you connected an Integra MD recorder, CD recorder,
or RI Dock?
If you have, see “Changing the Input Display” on page 51.
HDMI
OUT
TAPE
40
IN
CD recorder, MD recorder,
RI Dock
First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
Using Audyssey 2EQ
Automatic Speaker Setup
(Audyssey 2EQ)
With the supplied speaker setup microphone, the
Audyssey 2EQ function can measure the number of
speakers connected, their sizes, crossover frequencies,
and the distance from each speaker to the listening position and calculate the optimal speaker settings for your
listening environment automatically.
Before using this function, connect and position all of
your speakers.
1
Measurement Points
2, 9
To create a listening area in which several people can
enjoy home theater simultaneously, the Audyssey 2EQ
function takes measurements at three points within the
listening area:
First measurement point
This is the center point of the listening area, or the
listening position if it’s just one person.
3-8
Second measurement point
The right side of the listening area.
Third measurement point
The left side of the listening area.
The distances between points and and points and must be at least 1 meter.
From the examples below, choose the listening area that
best matches yours and place the microphone accordingly when prompted.
TV
TV
TV
Note: If any of your speakers is 4 ohms, change the
minimum speaker impedance setting before running
the automatic speaker setup (see page 51).
TV
TV
TV
TV
TV
TV
Notes:
• If the AV receiver was previously muted, it will
be unmuted.
• Automatic speaker setup cannot be performed
while a pair of headphones is connected.
• It takes about 10 minutes to complete the automatic speaker setup.
: listening area
: listening position
1
Turn on the AV receiver and the
connected TV.
On the TV, select the input to which the
AV receiver is connected.
41
First Time Setup—Continued
2
Put the speaker setup microphone at measurement point (page 41), and connect it to the
Setup Mic jack.
Auto Speaker Setup
4
The speaker detect results
appear.
Auto Speaker Setup
AUDYSSEY
- - - - - SP Detect Result - - - - FL
SL
SBL
C
AUDYSSEY
:
:
:
:
Yes
Yes
Yes
No
FR
SR
SBR
SW
:
:
:
:
Yes
Yes
Yes
Yes
Please place microphone at center
Next
Retry
Cancel
of listening area at ear height.
“Yes” means that the speaker was
detected. “No” means that no speaker
was detected.
Push Enter : Next
Notes:
• Make sure the microphone is horizontal.
• If there’s an obstacle between the
microphone and any speaker, the
automatic setup will not work correctly. Set up the room as you would
when enjoying a DVD.
• Positioning the microphone close to
where your ears would normally be
will provide better results. You can
adjust the height of the microphone
by using a tripod or level table.
3
Press [Enter].
The automatic speaker setup starts.
Auto Speaker Setup
If you agree with the results, use
the Up and Down [ ]/[ ] buttons to select Next, and then
press [Enter].
The options are:
Next:
Proceed to the next step.
Retry:
Return to step 2 and try again.
Cancel:
Cancel the automatic speaker setup.
5
The following screen appears.
Auto Speaker Setup
AUDYSSEY
AUDYSSEY
Please place microphone at right end
Do not unplug microphone.
of listening area at ear height.
Please keep quiet.
Now Measuring. . .
A test tone is output by each speaker in
turn, as the Audyssey 2EQ function
determines which speakers are connected. This takes a few minutes.
Note:
If any extraneous noise is picked up by
the microphone, the automatic setup
may not work correctly, so don’t make
any noise.
42
Push Enter : Next
Move the speaker setup microphone to measurement point (page 41), then press [Enter].
Audyssey 2EQ performs more measurements. This takes a few minutes.
First Time Setup—Continued
6
The following screen appears.
Auto Speaker Setup
8
AUDYSSEY
When the calculations are complete, the following screen
appears.
Auto Speaker Setup
Please place microphone at left end
1.
2.
3.
4.
5.
of listening area at ear height.
AUDYSSEY
Save
Review SP Config
Review SP Distance
Review SP Level
Cancel
Push Enter : Next
Move the speaker setup microphone to measurement point (page 41), then press [Enter].
Audyssey 2EQ performs more measurements. This takes a few minutes.
7
Use the Up and Down [ ]/[ ]
buttons to select an option, and
then press [Enter].
The options are:
Save:
Save the calculated settings and exit
the automatic speaker setup.
Review SP Config:
Review the speaker configuration
settings (see “Reviewing the
Results” on page 45
Review SP Distance:
Review the speaker distance settings (see “Reviewing the Results”
on page 45).
Review SP Level:
Review the speaker level settings
(see “Reviewing the Results” on
page 45).
Cancel:
Cancel the automatic speaker setup.
When the measurements are
complete, the following screen
appears.
Auto Speaker Setup
AUDYSSEY
Calculating...
9
Disconnect the speaker setup
microphone.
Auto Speaker Setup
AUDYSSEY
Please unplug microphone.
Notes:
• When the automatic speaker setup is complete, the
Equalizer Settings (page 72) will be set to “Audyssey.”
• You can cancel the automatic speaker setup at any
point in this procedure simply by disconnecting the
setup microphone.
43
First Time Setup—Continued
Error Messages
Auto Speaker Setup
While the automatic speaker setup is in progress, one of
the following error messages may appear:
- - - - - Speaker Detect Error - - - - -
❏ Ambient noise is too high
FL
SL
SBL
C
Auto Speaker Setup
AUDYSSEY
:
:
:
:
Yes
--No
Yes
FR
SR
SBR
SW
:
:
:
:
AUDYSSEY
Yes
Yes
Yes
---
Retry
Cancel
Ambient noise is too high.
The right surround back speaker has been detected
but the left surround back speaker hasn’t.
Retry
Cancel
Auto Speaker Setup
This message appears if the background noise is too
loud and the measurements cannot be performed
properly.
Remove the source of the noise and try again.
Retry: Return to the measured point immediately
before and start set up again.
Cancel: Cancel the automatic speaker setup.
AUDYSSEY
- - - - - Speaker Detect Error - - - - FL
SL
SBL
C
:
:
:
:
Error
Yes
Yes
Yes
FR
SR
SBR
SW
:
:
:
:
Yes
Yes
Yes
Yes
Retry
Cancel
There is a problem with a speaker. The speaker may
be broken or the subwoofer may be emitting sound
that is too high.
❏ Speaker Detect Errors
Auto Speaker Setup
Auto Speaker Setup
AUDYSSEY
AUDYSSEY
- - - - - Speaker Detect Error - - - - FL
SL
SBL
C
:
:
:
:
Yes
----Yes
FR
SR
SBR
SW
:
:
:
:
No
-------
Speaker Detect Error
Retry
Cancel
Retry
Cancel
One of the front speakers has not been detected.
Auto Speaker Setup
AUDYSSEY
The number of speakers detected on the second or
third measurement was different to the number
detected on the first measurement.
- - - - - Speaker Detect Error - - - - FL
SL
SBL
C
:
:
:
:
Yes
----Yes
FR
SR
SBR
SW
:
:
:
:
Make sure speakers that cannot be detected are connected property.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker setup.
Yes
No
-----
Retry
Cancel
One of the surround speakers has not been detected.
❏ Write Error
Auto Speaker Setup
Auto Speaker Setup
AUDYSSEY
AUDYSSEY
- - - - - Speaker Detect Error - - - - FL
SL
SBL
C
:
:
:
:
Yes
----Yes
FR
SR
SBR
SW
:
:
:
:
Yes
No
Yes
---
Writing Error!
Retry
Cancel
Retry
Cancel
This message appears if saving fails.
The surround back speakers have been detected but
the surround speakers haven’t.
44
Try saving again. If this message appears after 2 or 3
attempts, the AV receiver is probably malfunctioning.
Contact the dealer from whom you purchased this unit.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker setup.
First Time Setup—Continued
Reviewing the Results
Changing the Speaker Settings Manually
Use the Up and Down [ ]/[ ]
buttons to select the settings that
you want to review, and then
press [Enter].
Auto Speaker Setup
AUDYSSEY
Using a Powered Subwoofer
Save
Review SP Config
Review SP Distance
Review SP Level
Cancel
The options are:
Review SP Config:
Review the speaker configuration
settings.
Auto Speaker Setup
AUDYSSEY
Review SP Config
Subwoofer
Front
Center
Surround
Surr Back
Surr Back Ch
In some situations, the measurements taken by the automatic speaker setup may not provide usable results. If
running the speaker setup a second time still doesn’t provide usable results, you’ll have to set the speaker settings
manually (see pages 68–73).
:
:
:
:
:
:
If you’re using a powered subwoofer, because it outputs
very low-frequency sound and its position is usually low,
it may not be detected by the automatic speaker setup. If
the subwoofer (SW) appears on the SP Detect Result
screen as “No,” increase the subwoofer’s volume to the
half-way point, set it to its highest crossover frequency,
and then try running the automatic speaker setup again.
Note that if the volume is set too high and the sound distorts, it may not be detected, so use an appropriate volume level. If the subwoofer has a low-pass filter switch,
set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.
Yes
Full Band
80Hz
100Hz
150Hz
2ch
Review SP Distance:
Review the speaker distance settings.
Auto Speaker Setup
AUDYSSEY
Review SP Distance
Front
Center
Surr Right
Surr Back R
Surr Back L
Surr Left
Subwoofer
:
:
:
:
:
:
:
15.0ft
15.0ft
7.0ft
7.0ft
7.0ft
7.0ft
15.0ft
Review SP Level:
Review the speaker level settings.
Auto Speaker Setup
AUDYSSEY
Review SP Level
Left
:
+12.0dB
Center
:
0.0dB
Right
:
-12.0dB
Surr Right
:
+3.0dB
Surr Back R
:
+4.0dB
Surr Back L
:
-6.0dB
Surr Left
:
-3.0dB
Subwoofer
:
0.0dB
Press the [Return] button to return to
the previous menu.
45
First Time Setup—Continued
About the Onscreen Setup Menus
The onscreen setup menus are displayed on the connected TV and provide a convenient way to change the AV receiver’s
settings.
Submenus
p. 47
p. 50
1.
2.
3.
4.
p. 68
p. 72
p. 51
Submenus
1. Input/Output Assign
1.
2.
3.
4.
5.
6.
7.
8.
DVD
VCR/DVR
CBL/SAT
GAME/TV
AUX
TAPE
TUNER
CD
p. 79
6. Miscellaneous
2. Speaker Setup
1.
2.
3.
4.
5.
p. 76
5. Listening Mode Preset
Monitor Out
HDMI Input
Component Video Input
Digital Input
Speaker Settings
Speaker Config
Speaker Distance
Level Calibration
Equalizer Settings
Main menu
1.
2.
3.
4.
5.
Volume Setup
OSD Setup
12V Trigger A Setup
12V Trigger B Setup
12V Trigger C Setup
p. 80
p. 52
p. 88
Menu
p. 74
p. 75
1.
2.
3.
4.
5.
6.
7.
8.
3. Audio Adjust
1.
2.
3.
4.
5.
Tone Control
Multiplex/Mono
PL II x/Neo:6
Dolby EX
Theater-Dimensional
Input/Output Assign
Speaker Setup
Audio Adjust
Source Setup
Listening Mode Preset
Miscellaneous
Hardware Setup
Lock Setup
p. 81
7. Hardware Setup
1.
2.
3.
4.
5.
Remote Control
Zone2
Tuner
Analog Multich
HDMI
p. 84
p. 53
p. 73
p. 81
p. 77
p. 78
4. Source Setup
DVD
1. IntelliVolume
2. A/V Sync
46
p. 83
8. Lock Setup
Lock
Unlocked
p. 82
First Time Setup—Continued
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “1. Input/Output Assign,” and then press
[Enter].
The Input/Output Assign menu
appears.
1
2, 3
2-4
1. Input/Output Assign
1, 5
1.
2.
3.
4.
Monitor Out
HDMI Input
Component Video Input
Digital Input
HDMI Monitor
If you connect your TV to the COMPONENT VIDEO
OUT, set the HDMI Monitor setting to No so that the
onscreen setup menus are displayed and composite
video and S-Video sources are upconverted* and output
by the COMPONENT VIDEO OUT.
3
Use the Up and Down [ ]/[ ]
buttons to select “1. Monitor
Out,” and then press [Enter].
The Monitor Out menu appears.
1–1. Monitor Out
Composite video, S-Video
Component video
HDMI Monitor
No
IN
OUT
Composite video, S-Video
Component video
If you connect your TV to the HDMI OUT, set the
HDMI Monitor setting to Yes so that the onscreen setup
menus are displayed and composite video, S-Video, and
component video sources are upconverted* and output
by the HDMI OUT. The onscreen setup menus are displayed on the HDMI OUT only.
Composite video, S-Video,
component video
HDMI
IN
OUT
Composite video, S-Video,
component video
HDMI
4
Use the Left and Right [ ]/[ ]
buttons to select:
No: Select this if your TV is connected to the MONITOR
OUT or COMPONENT
VIDEO OUT.
Yes: Select this if your TV is connected to the HDMI OUT.
5
Press the [Setup] button.
The Setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
47
First Time Setup—Continued
3
Video Input Setup
HDMI Input Setup
If you connect a video component to HDMI IN 1 or 2,
you must assign that input to an input selector. For example, if you connect your DVD player to HDMI IN 1, you
must assign HDMI IN 1 to the DVD input selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, you can set the AV receiver so that composite video, S-Video, and component video sources are
upconverted* and output by the HDMI OUT. You can set
this for each input selector by selecting the “- - -” option.
Composite video, S-Video,
component video
1–2. HDMI Input
DVD
VCR/DVR
CBL/SAT
GAME/TV
AUX
TAPE
TUNER
CD
1
2
Use the Up and Down [ ]/[ ]
buttons to select an input selector, and use the Left and Right
[ ]/[ ] buttons to select:
IN 1: Select if the video component
is connected to HDMI IN 1.
IN 2: Select if the video component
is connected to HDMI IN 2.
- - -: Output composite video,
S-Video, and component
video sources from the HDMI
OUT. The video output signal
from the HDMI OUT is the
one configured in “Component Video Setup” (see
page 49).
There are no assignments for TUNER.
5
Press the [Setup] button.
The Setup menu closes.
HDMI
HDMI
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “1. Input/Output Assign,” and then press
[Enter].
The Input/Output Assign menu
appears.
1. Input/Output Assign
1.
2.
3.
4.
48
Monitor Out
HDMI Input
Component Video Input
Digital Input
-----------------
4
IN
OUT
Composite video, S-Video,
component video
Use the Up and Down [ ]/[ ]
buttons to select “2. HDMI Input,”
and then press [Enter].
The HDMI Input menu appears.
Notes:
• Each HDMI IN cannot be assigned to more than one
input selector.
• For composite video, S-Video, and component video
upconversion for the HDMI OUT, the HDMI Monitor
setting must be set to Yes (see page 47), and the HDMI
Input setting must be set to “- - -.” See page 24 for
more information on video signal flow and upconversion.
• When an HDMI IN is assigned to an input selector as
explained here, the digital audio input for that input
selector is automatically set to the same HDMI IN.
See “Digital Input Setup” on page 50.
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
First Time Setup—Continued
Component Video Setup
3
If you connect to a COMPONENT VIDEO IN, you must
assign it to an input selector. For example, if you connect
your DVD player to COMPONENT IN 3, you should
assign it to the DVD input selector.
If you want to output composite and S-Video sources
from the COMPONENT VIDEO OUT, select “---,” as
explained below.
Input selector
VIDEO IN jack
DVD
IN 1
VCR/DVR
---
CBL/SAT
---
GAME/TV
---
AUX
---
TAPE
---
CD
---
1–3. Component Video Input
DVD
VCR/DVR
CBL/SAT
GAME/TV
AUX
TAPE
TUNER
CD
Use the Up and Down [ ]/[ ]
buttons to select an input selector, and then use the Left and
Right [ ]/[ ] buttons to select:
IN 1: Use the video component
connected to COMPONENT VIDEO IN 1.
IN 2: Use the video component
connected to COMPONENT VIDEO IN 2.
IN 3: Use the video component
connected to COMPONENT VIDEO IN 3.
- - -: Output composite video
and S-Video sources from
the COMPONENT
VIDEO OUT.
There are no assignments for TUNER.
5
Press the [Setup] button.
The setup menu closes.
Component video
IN
OUT
Composite video, S-Video
1
2
Component video
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “1. Input/Output Assign,” and then press
[Enter].
The Input/Output Assign menu
appears.
IN 1
---------------
4
If you’ve connected your TV to the AV receiver with a
component video cable, you can set the AV receiver so
that composite video and S-Video sources are upconverted* and output by the COMPONENT VIDEO OUT.
You can set this for each input selector by selecting the
“- - -” option.
Composite video, S-Video
Use the Up and Down [ ]/[ ]
buttons to select “3. Component
Video Input,” and then press
[Enter].
The Component Video Input menu
appears.
Notes:
• For composite video and S-Video upconversion for
the COMPONENT VIDEO OUT, the HDMI Monitor
setting must be set to No (see page 47), and the Component Video Input setting must be set to “- - -.” See
page 24 for more information on video signal flow and
upconversion.
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
1. Input/Output Assign
1.
2.
3.
4.
Monitor Out
HDMI Input
Component Video Input
Digital Input
49
First Time Setup—Continued
Digital Input Setup
4
Use the Up and Down [ ]/[ ]
buttons to select an input selector, and use the Left and Right
[ ]/[ ] buttons to select
COAX 1, COAX 2, OPT 1, OPT 2,
or - - - (analog).
• An input selector that has been
assigned to IN 1 or IN 2 in the
“HDMI Input Setup” (see page 48)
can be set to HDMI here.
• There are no assignments for
TUNER.
• AUX is used only for digital input
from the front panel terminals.
Examples:
If you connect your DVD player to the
OPTICAL IN 1 jack, set “DVD” to
“OPT 1.”
If you want to listen to audio from the
component connected to the OPTICAL
IN 2 jack when the VCR/DVR input
selector is selected, set “VCR/DVR” to
“OPT 2.”
If you want to listen to audio from the
component connected to the COAXIAL IN 1 jack when the CBL/SAT
input selector is selected, set “CBL/
SAT” to “COAX 1.”
For input selectors that you don’t want
to assign a digital input jack, set to
“- - - (analog).”
There are no assignments for TUNER.
5
Press the [Setup] button.
The Setup menu closes.
If you connect a component to a digital input jack, you
must assign that jack to an input selector. For example, if
you connect your CD player to the OPTICAL IN2 jack,
you should assign that jack to the CD input selector. By
default, the COAXIAL IN1 jack is assigned to the DVD
input selector, although this can be changed.
Here are the default assignments.
Input selector
Default assignment
DVD
COAX 1
VCR/DVR
---
CBL/SAT
COAX 2
GAME/TV
OPT 1
AUX
FRONT
TAPE
---
CD
OPT 2
When HDMI IN 1 or 2 is assigned to an input selector in
the “HDMI Input Setup” on page 48, the input selector
assignment on this page is automatically set to HDMI 1
or HDMI 2.
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “1. Input/Output Assign,” and then press
[Enter].
The Input/Output Assign menu appears.
1. Input/Output Assign
1.
2.
3.
4.
Monitor Out
HDMI Input
Component Video Input
Digital Input
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
3
Use the Up and Down [ ]/[ ]
buttons to select “4. Digital
Input,” and then press [Enter].
The Digital Input menu appears.
1–4. Digital Input
DVD
VCR/DVR
CBL/SAT
GAME/TV
AUX
TAPE
TUNER
CD
50
COAX 1
--COAX 2
OPT 1
FRONT
----OPT 2
First Time Setup—Continued
Changing the Input Display
If you connect an
-capable Integra MiniDisc
recorder, CD recorder, or RI Dock to the TAPE IN/OUT
or GAME/TV IN jacks, for
to work properly, you
must change this setting.
This setting can only be changed on the AV receiver.
1, 2 1, 2
iPod photo: If you’re using an iPod photo with the
DS-A1 Remote Interactive Dock, connect the DS-A1 to
the GAME/TV IN jacks.
1
If you change these settings, you must run the automatic speaker setup again (see page 41).
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms (not North American model).
If you’ve connected your front speakers to the FRONT
and SURR BACK terminal posts for bi-amping, you
must change the Speaker Type setting. For hookup information, see “Bi-amping the Front Speakers” on page 21.
Notes:
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the volume.
1
Press the [Receiver] button, followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “2. Speaker
Setup,” and then press [Enter].
The Speaker Setup menu appears.
Press the [Tape] or [Game/TV]
input selector button so that
“TAPE” or “GAME/TV” appears
on the display.
Press and hold down the [Tape]
or [Game/TV] input selector button (about 3 seconds) to change
the setting.
Repeat this step to select MD, CDR, or
Dock.
For the Tape input selector, the setting
changes in this order:
TAPE o MD o CDR o DOCK
o
2
Speaker Settings
For the Game/TV input selector, the
setting changes in this order:
GAME/TV l DOCK
2. Speaker Setup
1.
2.
3.
4.
5.
3
Speaker Settings
Speaker Config
Speaker Distance
Level Calibration
Equalizer Settings
Use the Up and Down [ ]/[ ]
buttons to select “1. Speaker Settings,” and then press [Enter].
The Speaker Settings menu appears.
2–1. Speaker Settings
Speakers Impedance
Speakers Type
6 ohms
Normal
Note:
Dock can be selected for the Tape input selector or
Game/TV input selector, but not both at the same time.
51
First Time Setup—Continued
4
5
6
Use the Up and Down [ ]/[ ]
buttons to select “Speaker
Impedance,” and then use the
Left and Right [ ]/[ ] buttons to
select:
4 ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
6 ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
If the Speakers Type setting in step 5 is
set to Bi-Amp, this setting can not be
selected.
2
6. Miscellaneous
1.
2.
3.
4.
5.
3
Use the Up and Down [ ]/[ ]
buttons to select “Speakers
Type,” and then use the Left and
Right [ ]/[ ] buttons to select:
Normal: Select this if you’ve connected your front speakers
normally.
Bi-Amp:Select this if you’ve connected your front speakers for
bi-amped operation.
Press the [Setup] button.
The Setup menu closes.
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “2. OSD Setup,”
and then press [Enter].
The OSD Setup menu appears.
Immediate Display
Monitor Type
Display Position
TV Format
On
4:3
Bottom
Auto
4
Use the Up and Down [ ]/[ ]
buttons to select “TV Format,”
and then use the Left and Right
[ ]/[ ] buttons to select:
Auto: Select this to automatically
detect the TV system from
the video input signals.
NTSC: Select if the TV system in
your area is NTSC.
PAL: Select if the TV system in
your area is PAL.
5
When you’ve finished, press the
[Setup] button.
The setup menu closes.
TV Format Setup
(not North American model)
1
Volume Setup
OSD Setup
12V Trigger A Setup
12V Trigger B Setup
12V Trigger C Setup
6–2. OSD Setup
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
You must specify the TV system used in your area.
Use the Up and Down [ ]/[ ]
buttons to select
“6. Miscellaneous,” and then
press [Enter].
The Miscellaneous menu appears.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
52
First Time Setup—Continued
AM Frequency Step Setup
(Australian model)
You must specify the AM frequency step used in your
area. Note that when this setting is changed, all radio
presets are deleted.
1
Press the [Receiver] button, followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “7. Hardware
Setup,” and then press [Enter].
The Hardware Setup menu appears.
7. Hardware Setup
1.
2.
3.
4.
5.
3
Remote Control
Zone2
Tuner
Analog Multich
HDMI
Use the Up and Down [ ]/[ ]
buttons to select “3. Tuner,” and
then press [Enter].
The Tuner menu appears.
7–3. Tuner
AM Frequency Step
9 kHz
4
Use the Left and Right [ ]/[ ]
buttons to select:
10 kHz: Select if 10 kHz steps are
used in your area.
9 kHz: Select if 9 kHz steps are used
in your area.
5
Press the [Setup] button.
The Setup menu closes.
Note:
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
53
Basic Operations
Selecting the Input Source
This section explains how to select the input source (i.e., the AV component that you want to listen to or watch).
Multi CH
3
Multi CH
1
1
3
1
1
AV receiver
Remote
controller
To select the input source with the remote controller, press the
[Receiver] button, and then use the Input Selector buttons.
or
2
3
Start playback on the source component.
When you select DVD or another video component, on your TV, you’ll need
to select the video input that’s connected to the AV receiver’s COMPONENT
VIDEO OUT, HDMI OUT or MONITOR OUT.
On some DVD players, you may need to turn on the digital audio output.
AV receiver
Remote
controller
or
54
Use the AV receiver’s input selector buttons to select the input
source.
To adjust the volume, use the Master Volume control, or the remote
controller’s [VOL] button.
The volume can be set to MIN, 1 through 99, or MAX.
The AV receiver is designed for home theater enjoyment. It has a wide volume
range, allowing precise adjustment.
Basic Operations—Continued
Using the Multichannel DVD Input
The multichannel DVD input is for connecting a component with a 7.1-channel analog audio output, such as a
DVD-Audio or SACD-capable DVD player, or an
MPEG decoder. See page 28 for hookup information.
Press the [Receiver] button, followed by the [Multi CH] button.
The MULTI CH indicator appears on
the display.
Displaying Source Information
You can display various information about the current
input source as follows.
Press the [Receiver] button, and
then press the [Display] button
repeatedly to cycle through the
available information.
MULTI CH indicator
Audio from the multichannel DVD
input will now be used for the DVD
input source.
Note:
While the multichannel DVD input is selected, the
Speaker Configuration settings on page 68 are ignored,
and signals from the multichannel input are fed to the
speakers as they are.
Adjusting the Bass & Treble
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
1
Press the [Tone] button repeatedly to select either Bass or
Treble.
2
Use the Tone [–]/[+] buttons to
adjust.
Note:
This procedure can also be performed on the AV receiver
by using its [Display] button.
The following information can typically be displayed for
input sources.
Input source &
volume
Signal format*
or sampling
frequency
Input source &
listening mode
* If the input signal is analog, no format information is
displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not
PCM, the signal format is displayed. Information is
displayed for about three seconds, then the previously
displayed information reappears.
■ Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■ Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
55
Basic Operations—Continued
Press
[Receiver]
first
Dimmer
Sleep
Muting
Setting the Display Brightness
You can adjust the brightness of the display.
Press the [Receiver] button, and
then press the [Dimmer] button
repeatedly to select: dim, dimmer, or normal brightness.
Alternatively, you can use the AV
receiver’s [Dimmer] button.
Using the Sleep Timer
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
Press the [Receiver] button, and
then press the [Sleep] button
repeatedly to select the required
sleep time.
The sleep time can be set from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set. The specified sleep time appears on
the display for about five seconds, then
the previous display reappears.
If you need to cancel the sleep timer, press the [Sleep]
button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the AV receiver sleeps,
press the [Sleep] button. Note that if you press the
[Sleep] button while the sleep time is being displayed,
you’ll shorten the sleep time by 10 minutes.
Using Headphones
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the AV receiver’s Phones jack for private
listening, as shown.
Muting the AV receiver
You can temporarily mute the output of the AV receiver.
Press the [Receiver] button, and
then press the [Muting] button.
The output is muted and the MUTING
indicator flashes on the display, as
shown.
To unmute the AV receiver, press the
[Muting] button again, or adjust the
volume.
The Mute function is cancelled when
the AV receiver is set to Standby.
56
Notes:
• Always turn down the volume before connecting your
headphones.
• The speakers are turned off while the headphones plug
is inserted in the Phones jack (Zone 2 speakers are not
turned off).
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct.
• Only the Stereo, Direct, and Mono listening modes
can be used with headphones (the listening modes
available also depend on the currently selected input
source).
• When the multichannel input is used, only the front
left and right audio can be heard in the headphones.
• To adjust the headphone level, press the [CH SEL]
button on the remote controller, and then press the
[Level +]/[Level -] buttons. You can adjust the level
between –12 dB and +12 dB.
Listening to the Radio
■ Manual Tuning Mode
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
1
Press the [Tuning Mode] button
so that the AUTO indicator disappears from the display.
2
Press and hold the Tuning Up or
Down [ ]/[ ] buttons.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
Listening to the Radio
Use the [Tuner] input selector
button to select either AM or FM.
In this example, FM has been selected.
Each time you press the [Tuner] button,
the input source changes between AM
and FM.
Band
Frequency
(Actual display depends on country)
The North American models change FM frequency in
0.2 MHz steps, 10 kHz steps for AM. For other models
it’s 0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Tuning into Radio Stations
■ Tuning into Stations by Frequency
You can tune into AM and FM stations directly by entering the appropriate frequency.
1
2
1
Press the [Receiver] button, followed by the [D TUN] button.
■ Auto Tuning Mode
1
Press the [Tuning Mode] button
so that the AUTO indicator
appears on the display.
2
Press the Tuning Up or Down
[ ]/[ ] buttons.
Searching stops when a station is
found.
(Actual display depends on country.)
The [Receiver] button flashes.
2
Within 8 seconds, use the number buttons to enter the frequency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
Note: While the [Receiver] button is
flashing, the input source cannot be
changed by using the remote controller.
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator appears on the display, as shown.
FM STEREO
AUTO TUNED
57
Listening to the Radio—Continued
Presetting AM/FM Stations
Selecting Presets
Preset
2, 4
3
You can store a combination of up to 40 of your favorite
AM/FM radio stations as presets.
58
1
Tune into the AM/FM station that
you want to store as a preset.
2
Press the [Memory] button.
The preset number flashes.
3
While the preset number is flashing (about 8 seconds), use the
Preset [ ]/[ ] buttons to select
a preset from 1 through 40.
4
Press the [Memory] button again
to store the station or channel.
The station or channel is stored and the
preset number stops flashing.
Repeat this procedure for all of your
favorite AM/FM radio stations.
CH +/-
To select a preset, use the Preset
[ ]/[ ] buttons, or the remote
controller’s CH [+/–] button.
Deleting Presets
2
1
Select the preset that you want to
delete.
See the previous section.
2
While holding down the [Memory] button, press the
[Tuning Mode] button.
The preset is deleted and its number
disappears from the display.
Using the Listening Modes
Selecting Listening Modes
Selecting with the Remote Controller
See “About the Listening Modes” on page 64 for
detailed information about the listening modes.
• The Dolby Digital and DTS listening modes
can only be selected if your DVD player is
connected to the AV receiver with a digital
audio connection (coaxial or optical).
• Listening mode availability depends on the
format of the current input signal.
Selecting on the AV receiver
Stereo
Stereo
Listening
Mode /
Surround
■ [Surround] button
This button selects the Dolby Digital and DTS listening modes and the Neural Surround* listening mode
(*North American models only).
■ [Stereo] button
This button selects the Stereo listening mode.
Listening Mode
■ Listening Mode [ ]/[ ] buttons
Pressing these buttons repeatedly cycles through all
of the listening modes that can be used with the current input source.
■ [Stereo] button
This button selects the Stereo listening mode.
■ Listening Mode [ ]/[ ] buttons
Pressing these buttons repeatedly cycles through all
of the listening modes that can be used with the current input source.
59
Using the Listening Modes—Continued
Listening Modes Available for Each Source Format
Analog and PCM Sources
Multichannel PCM
(32-192 kHz)
PCM
Source format
32-96 kHz
Media
176.4/192 kHz*1
CD, TV, radio
Listening mode
Multichannel, 1/0, 1+1
DVD
Direct
✔
✔
Stereo
✔
✔
✔
✔
Multichannel
Dolby D
Dolby Digital Plus
DTS, DTS 96/24
DTS Discrete/Matrix
DTS-HD High Resolution
Audio
DTS-HD Master Audio
TrueHD
Dolby PLII Movie/
Dolby PLIIx Movie*2
✔
Dolby PLII Music/
Dolby PLIIx Music*2
✔
Dolby PLII Game/
Dolby PLIIx Game*2
✔
Dolby Digital EX/Dolby EX
Neo:6
Neo:6 Cinema
✔
Neo:6 Music
✔
Neural Surround (North
American model only)
✔*3
✔
Mono
Onkyo Original DSP*5
*4
*1.
*2.
*3.
*4.
*5.
Mono Movie
Orchestra*4
Unplugged*4
Studio-Mix*4
TV Logic*4
✔
All Ch Stereo
Full Mono
✔
T-D
✔
For PCM 176.4/192 kHz signals input through HDMI IN, only, Direct and Stereo listening modes can be selected. (HDMI input only)
If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.
PCM 32-48 kHz signals only.
Available only when using surround speakers.
For T-D, Mono Movie, Orchestra, Unplugged, Studio-Mix, and TV Logic, PCM of 64 kHz, 88.2 kHz, and 96 kHz are processed at 32 kHz, 44.1 kHz,
and 48 kHz respectively.
: Requires 6.1/7.1 speakers. Not available while Powered Zone 2 is being used.
: Requires 7.1 speakers. Not available while Powered Zone 2 is being used.
Tip: To check the format of the digital input signal, see “Displaying Source Information” on page 55.
60
Using the Listening Modes—Continued
Dolby Digital, Dolby Digital Plus, and TrueHD Sources
Dolby D
Source format
Multichannel
*/2
Media
except
*/2
Multichannel
2ch
1/0, 1+1
*/2
DVD, DTV, etc.
Listening mode
TrueHD*1
Dolby Digital Plus
except
*/2
2ch
1/0, 1+1
Blu-ray, HD DVD
Multichannel
2ch
1/0, 1+1
Blu-ray, HD DVD
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔*2
✔*2
Multichannel
Dolby D
Dolby Digital Plus
DTS, DTS 96/24
DTS Discrete/Matrix
DTS-HD High Resolution
Audio
DTS-HD Master Audio
✔
TrueHD
Dolby PLII Movie/
Dolby PLIIx Movie*3
✔
✔
✔
✔
Dolby PLII Music/
Dolby PLIIx Music*3
✔
✔
✔
✔
Dolby PLII Game/
Dolby PLIIx Game*3
✔
✔
Dolby Digital EX/Dolby EX
✔
✔
Neo:6
✔
✔
Neo:6 Cinema
✔
✔
Neo:6 Music
✔
✔
Neural Surround (North
American model only)
✔
✔
✔
✔
Mono
Orchestra*4
Unplugged*4
Studio-Mix*4
TV Logic*4
✔
✔
✔
✔
All Ch Stereo
Full Mono
✔
✔
✔
✔
T-D
✔
✔
✔
✔
Mono
✔
✔
✔
✔
✔
✔
✔
✔
Onkyo Original DSP
Movie*4
*1. During input of a 96 kHz TrueHD signal, the only sound balance or sound quality adjustment that can be made is Tone control. The AV receiver
does not respond to a 192 kHz TrueHD signal.
*2. If there are no surround back speakers, depending on the input signal, Dolby Digital may be used.
*3. If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.
*4. Available only when using surround speakers.
: Requires 6.1/7.1 speakers. Not available while Powered Zone 2 is being used.
: Requires 7.1 speakers. Not available while Powered Zone 2 is being used.
Tip: To check the format of the digital input signal, see “Displaying Source Information” on page 55.
61
Using the Listening Modes—Continued
DTS and DTS 96/24 Sources
DTS, DTS 96/24
Source format
Multichannel
DTS Discrete/Matrix
2ch
*/2
Media
1/0
except */2
DVD, CD, etc.
Listening mode
DVD, CD, etc.
Direct
✔
✔
✔
✔
✔
Stereo
✔
✔
✔
✔
✔
✔
✔
Multichannel
Dolby D
Dolby Digital Plus
DTS, DTS 96/24
✔
✔*1
DTS Discrete/Matrix
DTS-HD High Resolution
Audio
DTS-HD Master Audio
TrueHD
Dolby PLII Movie/
Dolby PLIIx Movie*2
✔
✔
Dolby PLII Music/
Dolby PLIIx Music*2
✔
✔
Dolby PLII Game/
Dolby PLIIx Game*2
✔
Dolby Digital EX/Dolby EX
✔
Neo:6
✔
Neo:6 Cinema
✔
Neo:6 Music
✔
Neural Surround (North
American model only)
✔
✔
✔
✔
✔
Mono
Orchestra*3
Unplugged*3
Studio-Mix*3
TV Logic*3
✔
✔
✔
✔
✔
All Ch Stereo
Full Mono
✔
✔
✔
✔
✔
T-D
✔
✔
✔
✔
✔
Onkyo Original DSP*4
Mono
*1.
*2.
*3.
*4.
Movie*3
If there are no surround back speakers, or Powered Zone 2 is being used, DTS is used.
If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.
Available only when using surround speakers.
For T-D, Mono Movie, Orchestra, Unplugged, Studio-Mix, and TV Logic, DTS 96/24 is processed as DTS.
: Requires 6.1/7.1 speakers. Not available while Powered Zone 2 is being used.
: Requires 7.1 speakers. Not available while Powered Zone 2 is being used.
Tip: To check the format of the digital input signal, see “Displaying Source Information” on page 55.
62
Using the Listening Modes—Continued
DTS-HD High Resolution Audio and DTS-HD Master Audio Sources
DTS-HD High Resolution Audio
Source format
Multichannel
2ch
*/2
Media
1/0
except *2
DTS-HD Master Audio*1
Multichannel
Blu-ray, HD DVD
Listening mode
2ch
1/0
Blu-ray, HD DVD
Direct
✔
✔
✔
✔
✔
✔
✔
Stereo
✔
✔
✔
✔
✔
✔
✔
✔
✔
Multichannel
Dolby D
Dolby Digital Plus
DTS, DTS 96/24
DTS Discrete/Matrix
DTS-HD High Resolution
Audio
✔
DTS-HD Master Audio
TrueHD
Dolby PLII Movie/
Dolby PLIIx Movie*2
✔*3
✔*3
Dolby PLII Music/
Dolby PLIIx Music*2
✔*3
✔*3
Dolby PLII Game/
Dolby PLIIx Game*2
✔*3
Dolby Digital EX/Dolby EX
✔*3
Neo:6
✔*3
Neo:6 Cinema
✔*3
Neo:6 Music
✔*3
Neural Surround (North
American model only)
Mono
✔*3
✔*3
✔*3
✔*3
✔*3
✔*3
✔*3
✔*3
Onkyo Original DSP
*4
Mono Movie
Orchestra*4
Unplugged*4
Studio-Mix*4
TV Logic*4
All Ch Stereo
Full Mono
T-D
*1. During input of a 96 kHz DTS-HD Master Audio signal, the only sound balance or sound quality adjustment that can be made is Tone control. When
input is a 192 kHz DTS-HD Master Audio signal, it should be played at 96 kHz.
*2. If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.
*3. Depending on the input source (when the input is a 96 kHz signal, for example), it may be processed after DTS playback.
*4. Available only when using surround speakers.
: Requires 6.1/7.1 speakers. Not available while Powered Zone 2 is being used.
: Requires 7.1 speakers. Not available while Powered Zone 2 is being used.
Tip: To check the format of the digital input signal, see “Displaying Source Information” on page 55.
63
Using the Listening Modes—Continued
About the Listening Modes
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall, with
high fidelity and stunning surround sound.
The illustration shows which speakers are active in
each listening mode with 7.1 channel speaker system.
Front left
Center
Front right
Subwoofer
Surround left
Surround
back left/ right
Surround right
Direct
In this mode, audio from the input source is output
directly with minimal processing, providing high-fidelity reproduction. All of the source’s audio channels are
output as they are.
Dolby Digital
Use this mode with DVDs that bear the Dolby Digital
logo, and Dolby Digital TV broadcasts. This is the most
common digital surround-sound format, and it’ll put you
right in the middle of the action, just like being in a
movie theater or concert hall.
5.1-channel source + Dolby EX
These modes expand 5.1-channel sources for 6.1/7.1channel playback. They’re especially suited to Dolby EX
soundtracks that include a matrix-encoded surround
back channel. The additional channel adds an extra
dimension and provides an enveloping surround sound
experience, perfect for rotating and fly-by sound effects.
Dolby Digital Plus
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from Dolby. It supports up to 7.1
channels with 48 kHz sampling rate.
Stereo
Dolby TrueHD
Sound is output by the front left and right speakers and
subwoofer.
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc formats, this new Dolby format offers up to 7.1 discrete
channels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate.
For the signals supported by the AV receiver, see
page 61.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or use it with the foreign language
soundtracks recorded in the left and right channels of
some movies. It can also be used with DVDs or other
sources containing multiplexed audio, such as karaoke
DVDs.
Dolby Pro Logic IIx
5.1-channel source + Dolby PLIIx Music
These modes use the Dolby Pro Logic IIx Music mode
to expand 5.1-channel sources for 6.1/7.1-channel playback.
Dolby Pro Logic II
Dolby Pro Logic IIx expands any 2-channel source for
7.1-channel playback. It provides a very natural and
seamless surround-sound experience that fully envelops
the listener. As well as music and movies, video games
can also benefit from the dramatic spatial effects and
vivid imaging. If you’re not using any surround back
speakers, Dolby Pro Logic II will be used instead of
Dolby Pro Logic IIx.
•
Dolby PLIIx Movie
Use this mode with any stereo or Dolby Surround
(Pro Logic) movie (e.g., TV, DVD, VHS).
•
•
64
5.1-channel source + Dolby PLIIx Movie
These modes use the Dolby Pro Logic IIx Movie mode
to expand 5.1-channel sources for 7.1-channel playback.
DTS
The DTS digital surround-sound format supports up to
5.1 discrete channels and uses less compression for highfidelity reproduction. Use it with DVDs and CDs that
bear the DTS logo.
DTS 96/24
Use this mode with any stereo or Dolby Surround
(Pro Logic) music source (e.g., CD, radio, cassette,
TV, VHS, DVD).
This mode is for use with DTS 96/24 sources. This is
high-resolution DTS with a 96 kHz sampling rate and
24-bit resolution, providing superior fidelity. Use it with
DVDs that bear the DTS 96/24 logo.
Dolby PLIIx Game
DTS-ES Discrete
Use this mode with video games, especially those
that bear the Dolby Pro Logic II logo.
This mode is for use with DTS-ES Discrete soundtracks,
which use a discrete surround back channel for true 6.1/
7.1-channel playback. The seven totally separate audio
channels provide better spatial imaging and 360-degree
sound localization, perfect for sounds that pan across the
surround channels. Use it with DVDs that bear the DTSES logo, especially those with a DTS-ES Discrete
soundtrack.
Dolby PLIIx Music
Using the Listening Modes—Continued
DTS-ES Matrix
This mode is for use with DTS-ES Matrix soundtracks,
which use a matrix-encoded back-channel for 6.1/7.1channel playback. Use it with DVDs that bear the DTSES logo, especially those with a DTS-ES Matrix
soundtrack.
Onkyo Original DSP Modes
Mono Movie
This mode is suitable for old movies and other mono
sources. The center speaker outputs the sound as it is,
while reverb is applied to the sound output by the other
speakers, giving presence to even mono material.
DTS Neo:6
This mode expands any 2-channel source for 7.1-channel playback. It uses seven full-bandwidth channels of
matrix decoding for matrix-encoded material, providing
a very natural and seamless surround sound experience
that fully envelops the listener.
•
•
Orchestra
Suitable for classical or operatic music, this mode
emphasizes the surround channels in order to widen the
stereo image, and simulates the natural reverberation of
a large hall.
Neo:6 Cinema
Unplugged
Use this mode with any stereo movie (e.g., TV, DVD,
VHS).
Neo:6 Music
Suitable for acoustic instruments, vocals, and jazz, this
mode emphasizes the front stereo image, giving the
impression of being right in front of the stage.
Use this mode with any stereo music source (e.g.,
CD, radio, cassette, TV, VHS, DVD).
Studio-Mix
5.1-channel source + Neo:6
This mode uses Neo:6 to expand 5.1-channel sources for
6.1/7.1-channel playback.
DTS-HD High Resolution Audio
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from DTS. It supports up to 7.1
channels with 96 kHz sampling rate.
DTS-HD Master Audio
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc formats, this new DTS format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-channels
with 192 kHz sampling rate.
For the signals supported by the AV receiver, see
page 63.
Suitable for rock or pop music, listening to music in this
mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.
TV Logic
This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire
sound, and clarity to voices.
All Ch Stereo
Ideal for background music, this mode fills the entire listening area with stereo sound from the front, surround,
and surround back speakers.
Full Mono
In this mode, all speakers output the same sound in
mono, so the sound you hear is the same regardless of
where you are within the listening room.
T-D (Theater-Dimensional)
Neural Surround
(North American models only)
Neural Surround represents the latest advancement in
surround technology developed for music and is adopted
by XM Satellite Radio for digital radio broadcast of surround recordings and live events in surround sound.
Neural Surround employs psychoacoustic frequencydomain processing, which allows delivery of a more
detailed sound stage, with superior channel separation
and localization of audio elements. System playback is
scalable from 5.1 to 7.1 multichannel surround playback.
or
With this mode you can enjoy a virtual 5.1 surround
sound even with only two or three speakers. This works
by controlling how sounds reach the listener’s left and
right ears. Good results may not be possible if there’s too
much reverb, so we recommend that you use this mode
in an environment with little or no natural reverb.
65
Recording
This section explains how to record the selected input
source to a component with recording capability, and
how to record audio and video from different sources.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• You cannot record from the DVD analog multichannel
input.
• Various restrictions apply to digital recording. Refer
to the manuals supplied with your digital recording
equipment for more details.
• Digital input signals are output by only the digital outputs, and analog input signals are output by only the
analog outputs. There is no internal conversion from
digital to analog or vice versa.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
Recording Separate AV Sources
Here you can record audio and video from completely
separate sources, allowing you to overdub audio onto
your video recordings. This function takes advantage of
the fact that when an audio-only input source (i.e.,
TAPE, TUNER, or CD) is selected, the video input
source remains unchanged.
In the following example, audio from the CD player connected to the CD IN, and video from the camcorder connected to the AUX Input Video jack are recorded by the
VCR connected to the VCR/DVR OUT jacks.
Camcorder
video signal
audio signal
AV Recording
Audio sources can be recorded to a recorder (e.g., cassette deck, CDR, MD) connected to the TAPE OUT jack.
Video sources can be recorded to a video recorder (e.g.,
VCR, DVD recorder) connected to the to VCR/DVR
OUT jack. See pages 24 to 39 for hookup information.
1
Use the input selector buttons to
select the source that you want
to record.
You can watch the source while recording. The AV receiver’s Master Volume
control has no effect on recording.
CD player
66
2
On your recorder, start recording.
3
On the source component, start
playback.
If you select another input source during recording, that input source will be
recorded.
VCR
1
Prepare the camcorder and CD player for
playback.
2
Prepare the VCR for recording.
3
Press the [AUX] input selector button.
4
Press the [CD] input selector button.
This selects the CD player as the audio source, but
leaves the camcorder as the video source.
5
Start recording on the VCR and start playback on the camcorder and CD player.
The video from the camcorder and the audio from
the CD player are recorded by the VCR.
Advanced Operations
Using the CinemaFILTER
Receiver
CH SEL
L Night
With the CinemaFILTER, you can soften overly bright
movie soundtracks, which are typically mixed for reproduction in a movie theater.
CinemaFILTER can be used with the following listening
modes: Dolby Digital, Dolby Digital EX, Dolby Pro
Logic IIx Movie, Dolby Pro Logic II Movie, DTS, DTSES, DTS Neo:6 Cinema, DTS 96/24, and Neo:6.
Note:
The CinemaFILTER may not work when used with certain input sources.
Level –/+
CINE FLTR
Using the Late Night Function
(Dolby Digital, Dolby Digital Plus, and
Dolby TrueHD only)
With the Late Night function, you can reduce the
dynamic range of Dolby Digital, Dolby Digital Plus, and
Dolby TrueHD material so that you can still hear quiet
parts even when listening at low volume levels—ideal
for watching movies late at night when you don’t want to
disturb anyone.
Press the [Receiver] button, and
then press the [L Night] button
repeatedly to select:
Dolby Digital, Dolby Digital Plus:
Off: Late Night function off
(default).
Low: Small reduction in dynamic
range.
High: Big reduction in dynamic
range.
Dolby TrueHD:
Auto: The Late Night function is set
to On or Off automatically
(default).
Off: Late Night function off.
On: Late Night function on.
Notes:
• Depending on the design of the contents, there are
some materials that will show no effect even when the
Late Night mode is operating.
• The Late Night function resets to the default when the
AV receiver is set to Standby.
Press the [Receiver] button, and
then press the [CINE FLTR] button repeatedly to select:
On: CinemaFILTER on.
Off: CinemaFILTER off.
Adjusting Individual Speaker Levels
You can adjust the level of individual speakers during
playback. These adjustments are temporary and will be
cancelled when the AV receiver is set to Standby.
Press the [Receiver] button, use
the [CH SEL] button to select
each speaker, and use the
[Level–] and [Level+] buttons to
adjust the volume.
Speakers are selected in the following
order: Front Left o Center o Front
Righto Surr Right o Surr Back
Right o Surr Back Left o Surr Left
o Subwoofer.
You can adjust the volume of each
speaker from –12 dB to +12 dB
(–15 dB to +12 dB for the subwoofer)
in 1 dB steps.
The name of the currently selected
speaker and its volume appear on the
display, as shown.
Notes:
• You cannot use this function while the AV receiver is
muted.
• Speakers that are set to No or None in the Speaker
Configuration cannot be adjusted.
67
Advanced Setup
Speaker Setup
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “2. Speaker
Setup,” and then press [Enter].
The Speaker Setup menu appears.
Some of the settings in this section are set automatically
by the Automatic Speaker Setup function (see page 41).
Here you can check the settings made by the Automatic
Speaker Setup function, or set them manually, which is
useful if you change one of the connected speakers after
using the Automatic Speaker Setup function.
Speaker Settings
See “Speaker Settings” on page 51.
Speaker Configuration
2. Speaker Setup
This setting is set automatically by the Automatic
Speaker Setup function (see page 41).
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
The following crossover frequencies can be specified:
Full Band, 40 Hz, 45 Hz, 50 Hz, 55 Hz, 60 Hz, 70 Hz,
80 Hz, 90 Hz, 100 Hz, 120 Hz, 130 Hz, 150 Hz, or
200 Hz.
Specify Full Band for speakers that can output low-frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify
a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine
the optimum crossover frequencies.
1.
2.
3.
4.
5.
3
Speaker Settings
Speaker Config
Speaker Distance
Level Calibration
Equalizer Settings
Use the Up and Down [ ]/[ ]
buttons to select “2. Speaker
Config,” and then press [Enter].
The Speaker Config menu appears.
2–2. Speaker Config
Subwoofer
Front
Center
Surround
Surr Back
Surr Back Ch
LPF of LFE
Double Bass
Yes
100Hz
100Hz
100Hz
100Hz
2ch
120Hz
Off
1
4
Use the Up and Down [ ]/[ ]
buttons to select “Subwoofer,”
and then use the Left and Right
[ ]/[ ] buttons to select:
Yes: Select if a subwoofer is connected.
No: Select if no subwoofer is connected.
5
Use the Up and Down [ ]/[ ]
buttons to select “Front,” and
then use the Left and Right [ ]/
[ ] buttons to select a crossover
frequency.
Note:
If the Subwoofer setting in step 4 is set
to No, this setting is fixed at Full Band.
2, 3
2-11
1, 12
68
Advanced Setup—Continued
6
7
8
9
Use the Up and Down [ ]/[ ]
buttons to select “Center,” and
then use the Left and Right [ ]/
[ ] buttons to select a crossover
frequency.
If no center speaker is connected, select
None.
Note:
If the Front setting in step 5 is set to
anything other than Full Band, Full
Band cannot be selected here.
Use the Up and Down [ ]/[ ]
buttons to select “Surround,”
and then use the Left and Right
[ ]/[ ] buttons to select a
crossover frequency.
If no surround left and right speakers
are connected, select None.
Note:
If the Front setting in step 5 is set to
anything other than Full Band, Full
Band cannot be selected here.
Use the Up and Down [ ]/[ ]
buttons to select “Surr Back,”
and then use the Left and Right
[ ]/[ ] buttons to select a
crossover frequency.
If no surround back speakers are connected, select None.
Notes:
• If the Surround setting in step 7 is set
to None, this setting cannot be
selected.
• If the Surround setting in step 7 is set
to anything other than Full Band,
Full Band cannot be selected here.
Use the Up and Down [ ]/[ ]
buttons to select “Surr Back Ch,”
and then use the Left and Right
[ ]/[ ] buttons to select:
1ch: Select if one surround back
speaker is connected.
2ch: Select if two (left and right)
surround back speakers are
connected.
Note:
If the Surr Back Setting in step 8 is set
to None, this setting cannot be selected.
Continue with step 10 in the right column.
Low-Pass Filter for the LFE Channel
This setting is not set automatically by the Automatic
Speaker Setup function (see page 41).
With this setting, you can specify the cutoff frequency of
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
10
Use the Up and Down [ ]/[ ]
buttons to select “LPF of LFE,”
and then use the Left and Right
[ ]/[ ] buttons to select a lowpass filter frequency.
The following low-pass filter frequencies can be selected: 80 Hz, 100 Hz, or
120 Hz (default).
Continue with step 11 below.
Double Bass
This setting is not set automatically by the Automatic
Speaker Setup function (see page 41).
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting in step 4 is set to Yes, and the
Front setting in step 5 is set to Full Band.
In the speaker setup screen, you can choose how bass
information is distributed to your speakers only if you
have large front left and right speakers AND a subwoofer.
11
Use the Up and Down [ ]/[ ]
buttons to select “Double Bass,”
and then use the Left and Right
[ ]/[ ] buttons to select:
On: Double Bass function on
(default). Front left and right
bass also goes to the subwoofer simultaneously.
Off: Double Bass function off.
12
Press the [Setup] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
69
Advanced Setup—Continued
Speaker Distance
3
This setting is set automatically by the Automatic
Speaker Setup function (see page 41).
Use the Up and Down [ ]/[ ]
buttons to select “3. Speaker Distance,” and then press [Enter].
The Speaker Distance menu appears.
2–3. Speaker Distance
Here you can specify the distance from each speaker to
the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
Unit
Left
Center
Right
Surr Right
Surr Back R
Surr Back L
Surr Left
Subwoofer
1
feet
12.0ft
12.0ft
12.0ft
7.0ft
7.0ft
7.0ft
7.0ft
12.0ft
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 68) cannot be selected.
4
Use the Up and Down [ ]/[ ]
buttons to select “Unit,” and then
use the Left and Right [ ]/[ ]
buttons to select:
feet: Select if you want to enter distances in feet. Can be set from
1 to 30 feet in 0.5-feet steps.
meters: Select if you want to enter
distances in meters. Can be
set from 0.3 to 9 meters in
0.15-meter steps.
5
Use the Up and Down [ ]/[ ]
buttons to select “Front,” and then
use the Left and Right [ ]/[ ]
buttons to specify the distance.
Specify the distance from the front left
speaker to your listening position.
6
Repeat step 5 for all speakers.
7
Press the [Setup] button.
The setup menu closes.
2, 3
2-6
1, 7
1
2
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “2. Speaker
Setup,” and then press [Enter].
The Speaker Setup menu appears.
2. Speaker Setup
1.
2.
3.
4.
5.
70
Speaker Settings
Speaker Config
Speaker Distance
Level Calibration
Equalizer Settings
Notes:
• The Center and Subwoofer distances can be set up to
5 ft. (1.5 m) more or less than the Front distance. For
example, if the Front distance is set to 20 ft. (6 m), the
Center and Subwoofer distances can be set between 15
and 25 ft. (4.5 and 7.5 m). The Surr Right, Surr Left,
Surr Back R, and Surr Back L distances can be set up
to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the
Front distance. For example, if the Front distance is set
to 20 ft. (6 m), the Surr Right, Surr Left, Surr Back R,
and Surr Back L distances can be set between 5 and
25 ft. (1.5 and 7.5 m).
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
Advanced Setup—Continued
Speaker Level Calibration
3
This setting is set automatically by the Automatic
Speaker Setup function (see page 41).
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Note:
The speakers cannot be calibrated while the output of the
AV receiver is muted or while a pair of headphones is
connected.
2–4. Level Calibration
Left
Center
Right
Surr Right
Surr Back R
Surr Back L
Surr Left
Subwoofer
4
Use the Up and Down [ ]/[ ]
buttons to select each speaker,
and use the Left and Right [ ]/
[ ] buttons to set the volume.
The volume can be adjusted from –12
to +12 dB (–15 dB to +12 dB for the
subwoofer) in 1 dB steps.
5
Repeat step 4 until the volume of
the test tone from each speaker
is the same.
6
Press the [Setup] button.
The setup menu closes.
2, 3
2-5
1, 6
2
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 68) cannot be selected.
1
1
Use the Up and Down [ ]/[ ]
buttons to select “4. Level Calibration,” and then press [Enter].
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “2. Speaker
Setup,” and then press [Enter].
The Speaker Setup menu appears.
Notes:
• This procedure can also be performed by using the
remote controller. First press the [Test Tone] button to
output the test tone. Use the [Level–] and [Level+]
buttons to set the volume, and use the [CH SEL] button to select the speakers.
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
2. Speaker Setup
1.
2.
3.
4.
5.
Speaker Settings
Speaker Config
Speaker Distance
Level Calibration
Equalizer Settings
71
Advanced Setup—Continued
Equalizer Setting
3
This setting is set automatically by the Automatic
Speaker Setup function (see page 41).
Use the Up and Down [ ]/[ ]
buttons to select “5. Equalizer
Settings,” and then press [Enter].
The Equalizer Settings menu appears.
2–5. Equalizer Settings
Here you can adjust the EQ of individual speakers. To set
the volume of individual speakers see page 71.
Equalizer
Off
1
4
Use the Left and Right [ ]/[ ]
buttons to select:
Off: Tone off, response flat.
Audyssey: The tone for each speaker
is set automatically by the
Automatic Speaker Setup
function.
Be sure to select this setting after having performed the Automatic
Speaker Setup.
Manual: You can adjust the EQ of
each speaker manually.
If you select Manual, continue with this
procedure. If you select Off or Audyssey, go to step 8.
5
Use the Down [ ] button to
select “Channel,” and then use
the Left and Right [ ]/[ ] buttons to select a speaker.
2, 3
2-7
1, 8
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2–5. Equalizer Settings
2
Equalizer
Channel
80Hz
250Hz
800Hz
2500Hz
8000Hz
Use the Up and Down [ ]/[ ]
buttons to select “2. Speaker
Setup,” and then press [Enter].
The Speaker Setup menu appears.
Manual
Front
0dB
0dB
0dB
0dB
0dB
2. Speaker Setup
1.
2.
3.
4.
5.
72
Speaker Settings
Speaker Config
Speaker Distance
Level Calibration
Equalizer Settings
6
Use the Up and Down [ ]/[ ]
buttons to select a frequency,
and then use the Left and Right
[ ]/[ ] buttons to adjust the
level at that frequency.
The volume at each frequency can be
adjusted from –6 to +6 dB in 1 dB
steps.
Tip: Low frequencies (e.g., 80 Hz)
affect bass sounds; high frequencies
(e.g., 8000 Hz) affect treble sounds.
Advanced Setup—Continued
7
8
Use the Up [ ] button to select
“Channel,” and then use the Left
and Right [ ]/[ ] buttons to
select another speaker.
Repeat step 6 and 7 for each speaker.
Press the [Setup] button.
The setup menu closes.
2
7. Hardware Setup
1.
2.
3.
4.
5.
3
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “4. Analog Multich,” and then press [Enter].
The Analog Multich menu appears.
Subwoofer Input Sensitivity
0dB
4
Use the Left and Right [ ]/[ ]
buttons to select a value.
You can select 0 dB, 5 dB, 10 dB, or
15 dB.
If you find that your subwoofer is too
loud, try the 10 dB or 15 dB setting.
5
Press the [Setup] button.
The setup menu closes.
Subwoofer Input Sensitivity
Some DVD players output the LFE channel from their
subwoofer output at 15 dB higher than normal. You can
change the subwoofer sensitivity to match your DVD
player. Note that this setting only affects signals connected to the SUBWOOFER input jack of the multichannel DVD input.
Remote Control
Zone2
Tuner
Analog Multich
HDMI
7–4. Analog Multich
Notes:
• When the listening mode is set to Direct, no effect will
be produced.
• Depending on the input source or listening mode, the
Equalizer settings may not produce the desired effect.
• This procedure can also be performed on the AV
receiver by using its [Setup] button, arrow buttons, and
[Enter] button.
Multichannel DVD Input Settings
Use the Up and Down [ ]/[ ]
buttons to select “7. Hardware
Setup,” and then press [Enter].
The Hardware Setup menu appears.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
73
Advanced Setup—Continued
Audio Adjust Functions
Here you can set listening mode-related settings and
functions.
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
The Audio Adjust functions are explained below.
Tone Control Settings
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
■ Front Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■ Front Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
2
Use the Up and Down [ ]/[ ]
buttons to select “3. Audio
Adjust,” and then press [Enter].
The Audio Adjust menu appears.
3. Audio Adjust
1.
2.
3.
4.
5.
Tone Control
Multiplex/Mono
PL II x/Neo:6
Dolby EX
Theater-Dimensional
3
Use the Up and Down [ ]/[ ]
buttons to select the functions,
and then press [Enter].
The function menu you selected
appears.
4
Use the Up and Down [ ]/[ ]
buttons to select the settings,
and use the Left and Right [ ]/
[ ] buttons to set them.
The settings are explained below.
5
When you’ve finished, press the
[Setup] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
74
Input Channel Settings
■ Multiplex Input Ch
This setting determines which channel is output from a
stereo multiplex source. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
Main: The main channel is output (default).
Sub: The sub channel is output.
Main/Sub: Both the main and sub channels are output.
■ Mono Input Ch
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening
mode.
L+R: Both the left and right channels are output
(default).
L: Only the left channel is output.
R: Only the right channel is output.
Advanced Setup—Continued
PLIIx/Neo:6 Music Mode Settings
Dolby EX Input Signal Setting
These settings provide for playing any 2-channel digital
source such as Dolby Digital, or 2-channel analog/PCM
source in the Dolby PLIIx Music listening mode.
■ Dolby EX
This setting determines how Dolby EX encoded signals
are handled. This setting is unavailable if no surround
back speakers are connected. This setting is effective
with Dolby Digital and Dolby Digital Plus only.
Auto: If the source signal contains a Dolby EX flag,
the Dolby EX listening mode is used
(default).
Manual: You can select any available listening mode.
■ Panorama
With this function, you can broaden the width of the
front stereo image when using the Dolby Pro Logic II
Music or Dolby Pro Logic IIx Music listening mode.
On: Panorama function on.
Off: Panorama function off (default).
■ Dimension
With this setting, you can move the sound field forward
or backward when using the Dolby Pro Logic II Music
or Dolby Pro Logic IIx Music listening mode. It can be
adjusted from –3 to +3 (default is 0). Lower settings
move the sound field forward. Higher settings move it
backward.
If the stereo image feels too wide, or there is too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it is in mono, or there is not enough surround
sound, move it backward.
■ Center Width
With this function, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
II Music or Dolby Pro Logic IIx Music listening mode.
Normally
if you are using a center speaker, the center channel
sound is output by only the center speaker. (If you are not
using a center speaker, the center channel sound will be
distributed to the front left and right speakers to create a
phantom center.) This setting controls the front left,
right, and center mix, allowing you to adjust the weight
of the center channel sound. It can be adjusted from 0 to
7 (default is 3).
T-D (Theater-Dimensional) Listening
Setting
■ Listening Angle
With this setting, you can specify the angle of the front
left and right speakers relative to the listening position.
Processing for the Theater-Dimensional listening mode
is based on this setting. Ideally, the front left and right
speakers should be equidistant from the listening position
and at an angle close to one of the two available settings.
Front left speaker
Front right speaker
20/40˚
Narrow: Select if the listening angle is 20 degrees.
Wide: Select if the listening angle is 40 degrees
(default).
■ Center Image
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel (stereo) sources. With
this setting, you can specify by how much the front left
and right channel output is attenuated in order to create
the center channel. It can be adjusted from 0 to 5 (default
is 2). This setting is unavailable if no surround speakers
are connected.
When set to 0, the front left and right channel output is
attenuated by half (–6 dB), giving the impression that the
sound is located centrally. This setting works well when
the listening position is considerably off center. When
set to 5, the front left and right channels are not attenuated, maintaining the original stereo balance.
75
Advanced Setup—Continued
Assigning Listening Modes to Input
Sources
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes during playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “5. Listening
Mode Preset,” and then press
[Enter].
The Listening Mode Preset menu
appears.
5. Listening Mode Preset
1.
2.
3.
4.
5.
6.
7.
8.
3
DVD
VCR/DVR
CBL/SAT
GAME/TV
AUX
TAPE
TUNER
CD
Use the Up and Down [ ]/[ ]
buttons to select the input
source that you want to set, and
then press [Enter].
The signal format selection menu
appears.
5–1. Listening Mode Preset
Analog/PCM
–
DVD –
Last Valid
Dolby Digital
Last Valid
DTS
Last Valid
D.F. 2ch
Last Valid
D.F. Mono
Last Valid
For input selectors that have no digital
input jacks, only “Analog” will be
available.
76
4
Use the Up and Down [ ]/[ ]
buttons to select the signal format that you want to set, and
then use the Left and Right [ ]/
[ ] buttons to select a listening
mode.
Only listening modes that can be used
with each input signal format can be
selected.
The Last Valid option means that the
listening mode selected last will be
used.
Analog/PCM: With this setting, you
can specify the listening mode to be
used when an analog (CD, TV, LD,
VHS, MD, turntable, radio, cassette,
cable, satellite, etc.) or PCM digital
(CD, DVD, etc.) audio signal is played.
Dolby Digital: With this setting, you
can specify the listening mode to be
used when a Dolby Digital format digital audio signal is played (DVD, etc.).
DTS: With this setting, you can specify
the listening mode to be used when a
DTS format digital audio signal is
played (DVD, LD, CD, etc.).
D.F. 2ch: With this setting, you can
specify the listening mode to be used
when a 2-channel (2/0) digital audio
signal (Dolby Digital, DTS) is played
(DVD, etc.).
D.F. Mono: With this setting, you can
specify the listening mode to be used
when a mono digital audio signal is
played (DVD, etc.).
Multich PCM: Specifies the default
listening mode for multichannel PCM
sources input via a HDMI IN, such as
DVD-Audio.
192k/176.4k: Specifies the default listening mode for high resolution
176.4 kHz and 192 kHz digital audio
sources such as DVD-Audio.
Dolby TrueHD: Specifies the default
listening mode for Dolby TrueHD
sources, such as Blu-ray or HD DVD
(input via HDMI).
DTS-HD Master Audio: Specifies the
default listening mode for DTS-HD
Master Audio sources, such as Blu-ray
or HD DVD (input via HDMI).
Advanced Setup—Continued
5
When you’ve finished, press the
[Setup] button.
The setup menu closes.
2
Use the Up and Down [ ]/[ ]
buttons to select “4. Source
Setup,” and then press [Enter].
The Source Setup menu appears.
4. Source Setup
DVD
1. IntelliVolume
2. A/V Sync
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
Source Setup
3
Use the Input Selector buttons on
the remote controller to select
the input source that you want to
set.
4
Use the Up and Down [ ]/[ ]
buttons to select
“1. IntelliVolume,” and then press
[Enter].
The IntelliVolume menu appears.
1
3
2, 4
4–1. IntelliVolume
2, 4, 5
DVD
IntelliVolume
0dB
1, 6
IntelliVolume
You can set the input level for each input source. This is
useful if some of your AV components are louder or quieter than others. IntelliVolume does not affect Zone 2.
While this menu is shown onscreen, you can select each
input source and set the levels while listening to and
comparing them.
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
5
If a component is too loud compared to your other components,
use the Left [ ] button to adjust
the level. If it’s too quiet, use the
Right [ ] button.
• The level can be set from –12 dB to
+12 dB in 1 dB steps.
6
When you’re finished, press the
[Setup] button.
The setup menu closes.
77
Advanced Setup—Continued
Correcting Sound and Picture Sync
When using progressive scanning on your DVD player,
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals. You can set it from 0 to 100 milliseconds
(msec) in 2 millisecond steps.
1
2
Press [Enter], and use the Left
and Right [ ]/[ ] buttons to
adjust the delay from 0 to 100 milliseconds in 2 millisecond steps.
To view the TV picture while setting
the delay, press [Enter].
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select “4. Source
Setup,” and then press [Enter].
The Source Setup menu appears.
4. Source Setup
DVD
1. IntelliVolume
2. A/V Sync
3
Use the Input Selector buttons on
the remote controller to select
the input source that you want to
correct.
This can be the [DVD], [VCR/DVR],
[CBL/SAT], [Game/TV], [AUX],
[Tape], [Tuner], or [CD] input source.
4
Use the Up and Down [ ]/[ ]
buttons to select “2. A/V Sync,”
and then press [Enter].
The A/V Sync menu appears.
4–2. A/V Sync
DVD
A/V Sync
(HDMI Lip Sync
20msec
0msec)
Press Enter to see picture.
If HDMI Lip Sync is enabled (see
page 82), and your TV or display supports HDMI Lip Sync, the HDMI Lip
Sync delay time is displayed underneath in parentheses.
78
5
Note:
• This setting is not available when the Direct listening
mode is used with an analog input signal.
• This procedure can also be performed on the remote
controller by using Input Selector buttons and [Enter]
button.
Press and hold, for more than 5 seconds, the input
selector button for the input source that you want to
correct. Use the Left and Right [ ]/[ ] buttons to
adjust the delay.
Advanced Setup—Continued
4
Volume Setup/OSD Setup
This section explains the items on the Miscellaneous
menu.
Volume Setup
1
Use the Up and Down [ ]/[ ]
buttons to select the settings,
and use the Left and Right [ ]/
[ ] buttons to set them.
Maximum Volume / Zone2 Maximum
Volume
With these preferences, you can prevent the volume being set too high by
specifying maximum volume levels for
the main room and Zone 2.
The range is from 50 to 99. To specify
no maximum volume, select Off.
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Power On Volume / Zone2 Power On
Volume
2
With these preferences, you can specify
the volume settings to be used in the
main room and Zone 2 when the AV
receiver is turned on.
The range is MIN, 1-99, MAX. To use
the same volume level that was used
when the AV receiver was turned off,
select Last.
The “Power On Volume” cannot be set
higher than the “Maximum Volume”
setting.
Use the Up and Down [ ]/[ ]
buttons to select
“6. Miscellaneous,” and then
press [Enter].
The Miscellaneous menu appears.
6. Miscellaneous
1.
2.
3.
4.
5.
Volume Setup
OSD Setup
12V Trigger A Setup
12V Trigger B Setup
12V Trigger C Setup
Headphone Level
3
With this preference, you can specify
the headphone volume relative to the
main volume. This is useful if there’s a
volume difference between your speakers and your headphones. The headphones level can be set from –12 dB to
+12 dB.
Use the Up and Down [ ]/[ ]
buttons to select “1. Volume
Setup,” and then press [Enter].
The Volume Setup menu appears.
6–1. Volume Setup
Maximum Volume
Power On Volume
Headphone Level
Zone2 Maximum Volume
Zone2 Power On Volume
Off
Last
0dB
Off
Last
5
When you’ve finished, press the
[Setup] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
79
Advanced Setup—Continued
OSD Setup
1
4
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select the settings,
and use the Left and Right [ ]/
[ ] buttons to set them.
These settings determine how the operation details are displayed.
Immediate Display
2
This preference determines whether
operation details are displayed
onscreen when an AV receiver function
is adjusted.
On: Displayed (default).
Off: Not displayed.
Even when On is selected, operation
details may not be output if the input
source is connected to a COMPONENT VIDEO IN or HDMI IN.
Use the Up and Down [ ]/[ ]
buttons to select
“6. Miscellaneous,” and then
press [Enter].
The Miscellaneous menu appears.
6. Miscellaneous
1.
2.
3.
4.
5.
3
Volume Setup
OSD Setup
12V Trigger A Setup
12V Trigger B Setup
12V Trigger C Setup
Monitor Type
With this preference, you can specify
the aspect ratio of your TV so that the
operation details are displayed properly.
4 : 3: Select if your TV is 4 : 3
(default).
16 : 9: Select if your TV is 16 : 9.
Use the Up and Down [ ]/[ ]
buttons to select “2. OSD Setup,”
and then press [Enter].
The OSD Setup menu appears.
Display Position
This preference determines where on
the screen operation details are displayed.
Bottom: Bottom of the screen
(default).
Top: Top of the screen.
6–2. OSD Setup
Immediate Display
Monitor Type
Display Position
TV Format
On
4:3
Bottom
Auto
TV Format (not North American
model)
See “TV Format Setup (not North
American model)” on page 52.
5
When you’ve finished, press the
[Setup] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
80
Advanced Setup—Continued
. Changing the AV receiver’s ID
HDMI Setup
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “7. Hardware
Setup,” and then press [Enter].
The Hardware Setup menu appears.
2
Use the Up and Down [ ]/[ ]
buttons to select “7. Hardware
Setup,” and then press [Enter].
The Hardware Setup menu appears.
7. Hardware Setup
1.
2.
3.
4.
5.
3
Remote Control
Zone2
Tuner
Analog Multich
HDMI
7. Hardware Setup
1.
2.
3.
4.
5.
Use the Up and Down [ ]/[ ]
buttons to select “1. Remote
Control,” and then press [Enter].
The Remote Control menu appears.
3
7–1. Remote Control
Remote ID
1
Remote Control
Zone2
Tuner
Analog Multich
HDMI
Use the Up and Down [ ]/[ ]
buttons to select “5. HDMI,” and
then press [Enter].
The HDMI menu appears.
7–5. HDMI
HDMI Audio Out
Lip Sync
xvYCC
Control
Power Control
TV Control
4
Use the Left and Right [ ]/[
buttons to select a value.
Off
Disable
Disable
Disable
-----
]
Remote ID
With this setting, you can change the
AV receiver’s remote control ID. You
may need to change this if the remote
controller’s control codes overlap with
those of another Integra component
located in the same room.
If you change the AV receiver’s remote
control ID, be sure to set the same ID
on both the AV receiver and remote
controller (see page 83). The default ID
for both is 1.
4
Use the Up and Down [ ]/[ ]
buttons to select the settings and
use the Left and Right [ ]/[ ]
buttons to select them.
The HDMI settings are explained on
page 82.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
81
Advanced Setup—Continued
HDMI Audio Out
This preference determines whether audio received at
the HDMI IN is output by the HDMI OUT. You may
want to turn this preference on if your TV is connected
to the HDMI OUT and you want to listen to the audio
from a component that’s connected to an HDMI IN,
through your TV’s speakers. Normally, this should be set
to Off.
Off: HDMI audio is not output (default).
On: HDMI audio is output.
Notes:
• If On is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• When TV Control is enabled, this setting is set to
Auto.
• With some TVs and input signals, no sound may be
output even when this setting is set to On.
Lip Sync
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Disable: HDMI lip sync disabled.
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 78).
xvYCC
If you set the xvYCC color function to Enable while a
source and monitor that both support the xvYCC color
standard are connected to HDMI, the color quality will
be improved.
Disable: xvYCC color disabled.
Enable: xvYCC color enabled.
Notes:
• If the color is unnatural when xvYCC color is set to
Enable, change the setting to Disable.
• Refer to the connected component’s instruction manual for details.
Control
This function allows CEC-standard-compatible equipment connected to HDMI and
-compatible
equipment to be operated together with the AV receiver.
Disable: HDMI Control disabled.
Enable: HDMI Control enabled.
Notes:
• Set to Disable when a connected piece of equipment is
not compatible or it is unclear whether the equipment
is compatible or not.
82
• If movement is unnatural when set to Enable, change
the setting to Disable.
• Refer to the connected component’s instruction manual for details.
■ Power Control
To link the electrical connection of CEC-standard-compatible equipment and
-compatible equipment
by means of HDMI, set to Enable. However, it may not
be possible to power link equipment, depending on the
settings and compatibility of the connected equipment.
Disable: Power Control disabled.
Enable: Power Control enabled.
Notes:
• The Power Control setting can be set only when the
above Control setting is set to Enable.
• HDMI power control only works with
-compatible components that support it.
• When set to Enable, power consumption will increase.
(North American model)
• The AV receiver enters Ready mode when set to
Standby. (Australian model)
• Refer to the connected component’s instruction manual for details.
■ TV Control
Set to Enable when you want to control the AV receiver
from an RIHD-compatible TV that is connected to
HDMI.
Disable: TV Control disabled.
Enable: TV Control enabled.
Notes:
• Set to Disable when the TV is not compatible or when
it is unclear whether the TV is compatible or not.
• The TV Control setting can be set only when the
above Control and Power Control settings are both set
to Enable.
• Refer to the connected component’s instruction manual for details.
Notes:
• After changing the settings of the Control, Power
Control, or TV Control, turn off the power to all
connected pieces of equipment and then turn on
again. Refer to the User’s Manuals for all connected pieces of equipment.
• When HDMI Audio Out is set to “On” or the TV
Control is set to “Enable” and the audio is playing
through the TV speakers, if the volume is
adjusted on the AV receiver, the audio will begin
to play through the speakers connected to the AV
receiver. If you want to turn off the audio from the
AV receiver, repeat the set up operation, and the
set up for the TV, or turn down the volume to its
lowest level.
Advanced Setup—Continued
2
Lock Setup
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “8. Lock Setup,”
and then press [Enter].
The Lock Setup menu appears.
8. Lock Setup
Lock
Unlocked
With this preference, you can protect
your settings by locking the setup
menus.
When the setup menus are locked, you
cannot change any setting.
Locked: Setup menus locked.
Unlocked: Setup menus not locked.
While “Auto” is displayed (about 3 seconds), press the [Enter] button again to
select: PCM, DTS, or Auto.
DTS or PCM: The DTS or PCM indicator,
depending on which format you have set, flashes,
and only signals in that format are output. Digital
signals in other formats are ignored.
Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.
Changing the Remote Controller’s ID
If several Integra components are used in the same room,
the remote controller’s control codes may overlap with
those of another component. To differentiate the remote
controller’s control codes, you can change its ID to
another number.
Note:
If you change the remote controller’s ID, be sure to set
the same ID on both the remote controller and AV
receiver (see “Changing the AV receiver’s ID” on
page 81). The default ID for both is 1.
Receiver
Number
buttons
Digital Input Signal Formats
The digital input signal formats are available only for the
input sources that you have assigned a digital input jack;
otherwise you will see “Analog” indicated on the screen
(see page 50).
Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
• If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
1
CINE FLTR
1
Hold down the [Receiver] and the [CINE
FLTR] buttons at the same time.
The [Receiver] button lights up.
2
Use the number buttons to enter a remote
control ID.
You can enter 1, 2, or 3.
Press and hold the remote controller’s
[Enter] button for about 3 seconds.
83
Zone 2
Using Only Speakers in Zone 2
Connecting Zone 2
With the Zone 2 function, you can enjoy one input
source in the main room and a different source in another
room.
There are two ways to hook up your Zone 2 speakers:
1) Use another amp (receiver, integrated amp, or power
amp) in Zone 2 and connect your Zone 2 speakers to it.
2) Connect your Zone 2 speakers to this AV receiver.
Note:
For speaker connections and related cautions, see
page 20.
With this connection method, you can use 5.1 surround
sound in the main room and play a different AV source
in Zone 2. The volume for Zone 2 is set on the AV
receiver.
Hookup
• Connect your Zone 2 speakers to the AV receiver’s
ZONE 2 SPEAKERS terminals.
Main room
TV
Using Another Amp in Zone 2
With this hookup, you can enjoy 7.1-channel playback in
the main room and a different stereo source in Zone 2. If
you use a receiver or integrated amp in Zone 2, the
volume for Zone 2 is adjusted on that unit. If you use a
power amp with no volume control in Zone 2, the volume for Zone 2 is adjusted on this AV receiver.
Hookup
• Use an RCA audio cable to connect the AV receiver’s
ZONE 2 PRE OUT L/R jacks to an analog audio input
on the amp in Zone 2.
• Connect the Zone 2 speakers to the speaker terminals
on the amp in Zone 2.
AV receiver
Zone 2
L
R
Main room
TV
AV receiver
You must set the “Powered Zone 2” setting to “Act”
(Activated) in order to use this hookup (see below).
ZONE 2
PRE OUT
Setting the Powered Zone 2
L
R
Zone 2
To use Zone 2, you must make this setting. It enables the
speakers connected to the ZONE 2 SPEAKERS terminals so that they produce sound when Zone 2 is used.
1
IN
R
L
Receiver/
integrated amp,
or power amp
If you’re using a receiver or integrated amp in Zone 2,
you don’t need to make any settings to use this hookup.
Proceed to “Using Zone 2” on page 86.
If you’re using a power amp with no volume control
in Zone 2, you must set the Zone 2 Out setting to Variable (see page 85).
84
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Zone 2—Continued
2
Use the Up and Down [ ]/[ ]
buttons to select “7. Hardware
Setup,” and then press [Enter].
The Hardware Setup menu appears.
7. Hardware Setup
1.
2.
3.
4.
5.
3
Remote Control
Zone2
Tuner
Analog Multich
HDMI
Use the Up and Down [ ]/[ ]
buttons to select “2. Zone2,” and
then press [Enter].
The Zone2 menu appears.
7–2. Zone2
Powered Zone2
Zone2 Out
Setting the Zone 2 Out
If you’ve connected your Zone 2 speakers to a power
amp with no volume control in Zone 2, as explained in
“Using Another Amp in Zone 2” on page 84, you must
set the Zone 2 Out setting to Variable.
When set to Variable, the ZONE 2 OUT L/R jacks work
like pre outs.
1
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select “7. Hardware
Setup,” and then press [Enter].
The Hardware Setup menu appears.
Not Act
Fixed
7. Hardware Setup
1.
2.
3.
4.
5.
4
5
Use the Up and Down [ ]/[ ]
buttons to select “Powered
Zone2,” and use the Left and
Right [ ]/[ ] buttons to select:
Not Act: ZONE 2 SPEAKERS terminals deactivated.
Act: ZONE 2 SPEAKERS terminals activated.
When Zone 2 is activated and turned on
(see below), the speakers connected to
the ZONE 2 SPEAKERS terminals
output sound, but the speakers connected to the SURR BACK SPEAKERS terminals do not (when Zone 2 is
activated but not used, the surround
back speakers work as normal).
Press the [Setup] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
3
Remote Control
Zone2
Tuner
Analog Multich
HDMI
Use the Up and Down [ ]/[ ]
buttons to select “2. Zone2,” and
then press [Enter].
The Zone2 menu appears.
7–2. Zone2
Powered Zone2
Zone2 Out
4
Not Act
Fixed
Use the Up and Down [ ]/[ ]
buttons to select “Zone2 Out,”
and use the Left and Right [ ]/
[ ] buttons to select:
Fixed: The ZONE 2 PRE OUT L/R
jacks work as line outs, and
the volume for Zone 2 is set
on the receiver or integrated
amp in Zone 2.
Variable:The ZONE 2 PRE OUT L/R
jacks work as pre outs, and the
volume for Zone 2 is set on
this AV receiver.
85
Zone 2—Continued
5
Press the [Setup] button.
The setup menu closes.
Controlling Zone 2 with the Remote
Controller
Zone 2
Standby/On
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
Iuput
Selector
Using Zone 2
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust
the volume for Zone 2.
Level –/+
Controlling Zone 2 from the AV receiver
1 2
Note:
• To control Zone 2, you must press the remote controller’s [Zone 2] button first.
1
To turn on Zone 2 and select an
input source, press the [Zone 2]
button repeatedly.
1
Press the [Zone 2] button, then
point the remote controller at the
AV receiver and press the
[Standby/On] button.
Zone 2 turns on, and the ZONE 2 12V
TRIGGER OUT goes high (+12 V).
2
To select an input source for
Zone 2, press the [Zone 2] button, followed by an Input Selector
button.
To select AM or FM press the [Tuner]
Input Selector button repeatedly.
3
To turn off Zone 2, press the
[Zone 2] button, followed by the
[Standby/On] button.
Alternatively, press the [Zone 2]
button followed by an input
selector button within 8 seconds.
Zone 2 turns on, the Zone 2 indicator
lights up, and the ZONE 2 12V TRIGGER OUT goes high (+12 V).
To select AM or FM press the [Tuner]
input selector button repeatedly.
To select the same source as that of the
main room, press the [Zone 2] button
repeatedly until “Z2 Sel: Source”
appears.
2
86
To turn off Zone 2, press the
Zone 2 [Off] button.
Zone 2—Continued
Adjusting the Volume for Zone 2
Zone 2 Level
,
Adjusting the Tone and Balance for Zone 2
You can adjust the bass, treble, and balance for Zone 2.
12
Remote controller
AV receiver
On the remote controller, press
the [Zone 2] button, and then use
the [Level–] and [Level+] buttons.
1
Press the [Zone 2] button, and
then press the [Tone] button
repeatedly to select Bass, Treble,
or Balance.
2
Use the Tone [+] and [–] buttons
to adjust.
On the AV receiver, use the
Zone 2 Level [ ]/[ ] buttons.
If your Zone 2 speakers are connected
to a receiver or integrated amp in Zone
2, use its volume control to adjust the
volume.
To Mute Zone 2:
Press the remote controller’s [Zone 2] button, followed
by the [Muting] button. To unmute Zone 2, press the
remote controller’s [Zone 2] button again, followed by
the [Muting] button, or adjust the volume for Zone 2.
Notes:
• Only analog input sources are output by the ZONE 2
PRE OUT and ZONE 2 SPEAKERS terminals. Digital input sources are not output. If no sound is heard
when an input source is selected, check if it’s connected to an analog input.
• While Zone 2 is being used, listening modes that need
surround back speakers (i.e., Dolby Digital EX and
DTS-ES) are unavailable.
• While Zone 2 is on,
functions will not work.
• You can’t select different radio stations for Zone 2 and
the main room. For example, if you have an FM station for the main room, that station will also be used in
Zone 2.
■ Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■ Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
■ Balance
You can adjust the balance of the left and right speakers
in Zone 2 in 2 dB steps, +10 dB to the right and +10 dB
to the left.
The balance cannot be adjusted when the Powered Zone
2 setting is set to Not Act (page 84) or the Zone 2 Out
setting is set to Fixed (page 85).
87
Zone 2—Continued
Using the 12V Triggers in Zone 2 and
the Main Room
4
Use the Up and Down [ ]/[ ]
buttons to select “Delay” or an
input source, and use the Left
and Right [ ]/[ ] buttons to
change the setting.
Repeat this step as necessary for each
setting.
5
Press the [Setup] button.
Setup closes.
When the AV receiver’s 12 V TRIGGER OUT A/B/C
jack is connected to the 12 V trigger input on a connected
component, you can specify whether or not a 12-volt
trigger signal is output when that component is selected
as the source for the main room, Zone 2, or either.
Hookup
• Use a miniplug cable to connect the AV receiver’s 12
V TRIGGER OUT A, B, or C jack to the 12 V trigger
input on the connected component.
1
2
Press the [Receiver] button followed by the [Setup] button.
The main menu appears onscreen.
Use the Up and Down [ ]/[ ]
buttons to select
“6. Miscellaneous,” and then
press [Enter].
The Miscellaneous menu appears.
6. Miscellaneous
1.
2.
3.
4.
5.
3
88
Volume Setup
OSD Setup
12V Trigger A Setup
12V Trigger B Setup
12V Trigger C Setup
Use the Up and Down [ ]/[ ]
buttons to select “12V Trigger
Setup” A, B, or C, and then press
[Enter].
■ Delay
When several components are turned on simultaneously
via the 12-volt triggers, depending on the type of components, a large amount of current may be drawn momentarily. To prevent this, you can delay the trigger signals
output by the AV receiver. In addition, by delaying the
trigger signal for your power amplifier so that it’s the last
component to be turned on, you can avoid the “thump”
noise that’s sometimes heard when a source component
is turned on.
The delay setting determines how long after the input
source is changed on the AV receiver the trigger signal is
output. It can be set to 0 sec, 1 sec, 2 sec, or 3 sec. When
set to 0 sec, the trigger signal is output as soon as the
input source is changed.
■ 12V Trigger Setting for Each Input Source
By default, all input sources on the 12V Trigger A Setup
menu are set to Main, those on the 12V Trigger B Setup
menu are set to Main/Zone 2, and those on the 12V Trigger C Setup menu are set to Zone 2.
Off: No trigger signal is output.
Main: Select this if you want to output a 12-volt trigger signal when a connected component is
selected as the source for the main room.
Zone2: Select this if you want to output a 12-volt trigger signal when a connected component is
selected as the source for Zone 2.
Main/Zone2: Select this if you want to output a 12-volt
trigger signal when a connected component is
selected as the source for either the main room
or Zone 2.
Zone 2—Continued
Using the Remote Controller in Zone
2 and Multiroom Control Kits
To control the AV receiver with the remote controller
while you’re in the Zone 2 room, you’ll need a commercially available multiroom remote control kit.
• Multiroom kits are made by Niles and Xantech.
These kits can also be used when there isn’t a clear line
of sight to the AV receiver’s remote sensor, such as when
it’s installed inside a cabinet.
Using a Multiroom Kit with a Cabinet
In this setup, the IR receiver picks up the infrared signals
from the remote controller and feeds them to the AV
receiver located in the cabinet via the connecting block.
IR receiver
Connecting
block
IR IN
A or B
Using a Multiroom Kit with Zone 2
In this setup, the IR receiver in Zone 2 picks up the infrared signals from the remote controller and feeds them
through to the AV receiver in the main room via the connecting block.
IR IN A or B
IR receiver
Connecting
block
Remote controller
Main room
Inside
cabinet
Remote controller
Signal flow
Using a Multiroom Kit with Other
Components
In this setup, an IR emitter is connected to the IR OUT
jack and placed in front of the other component’s remote
control sensor. Infrared signals received at the AV
receiver’s IR IN A or B jack are fed through to the other
component via the IR emitter. Signals picked up by the
AV receiver’s remote control sensor are not output.
Zone 2
Signal flow
The miniplug cable from the connecting block should be
connected to the AV receiver’s IR IN A or B jack, as
shown below. The IR IN A and B jacks are identical. Up
to two IR receivers can be connected.
IR receiver
Connecting
block
IR IN
A or B
IR OUT
DTR-5.8
IR emitter
Remote controller
from the connecting block
Other component
Miniplug cable
Signal flow
The IR emitter should be connected to the IR OUT jack,
as shown below.
Miniplug cable
Other component
Remote control
sensor
Emitter
Miniplug
IR emitter
Signal flow
89
Controlling Other Components
You can use the AV receiver’s remote controller
(RC-683M) to control your other AV components,
including those made by other manufacturers. This section explains how to enter the necessary remote control
code for the component that you want to control (e.g.,
DVD player, TV, or VCR).
2
While holding down the Remote
Mode button that you want to set,
press the [Display] button for 3
seconds.
The Remote Mode button lights up.
3
Within 30 seconds, use the number buttons to enter the 4-digit
remote control code.
The Remote Mode button flashes
twice.
4
Press the Remote Mode button
again to select the remote controller mode, point the remote
controller at the component, and
check the operation.
If the remote controller doesn’t work as
expected, and several remote codes are
listed, try each one in turn and use the
one that works best.
Receiver
Number
buttons
Display
Remote
Mode
L Night
Entering Remote Control Codes
To control another component, you must first enter the
appropriate remote control code to a Remote Mode button. You’ll need to enter a code for each component that
you want to control.
1
90
Look up the appropriate remote
control code in the separate
Remote Control Codes list.
The codes are organized by category
(e.g., DVD player, TV, etc.).
Notes:
• A remote control code cannot be entered for the
[Receiver] Remote Mode button.
• The remote control codes provided are correct at the
time of printing, but are subject to change.
Controlling Other Components—Continued
Remote Control Codes for Integra
Components Connected via
Integra components that are connected via
are controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
1
Make sure the Integra component is connected with an
cable and an analog
audio cable (RCA).
See page 39 for details.
2
Enter the appropriate remote control code
for the [DVD] or [CD] Remote Mode button.
[DVD] Remote Mode button
1612: Integra DVD player with
[CD/MD/CDR/Dock] Remote Mode button
1327: Integra CD player with
1808: Integra MD recorder with
1322: Integra CD recorder with
1993: Onkyo RI Dock with
See the previous page for how to enter remote
control codes.
3
Resetting Remote Mode Buttons
You can reset a Remote Mode button to its default
remote control code.
1
While holding down the Remote
Mode button that you want to
reset, press the [L Night] button
for 3 seconds.
The Remote Mode button lights up.
2
Press the Remote Mode button
again.
The Remote Mode button flashes
twice, indicating that it’s been reset.
Press the [DVD] or [CD] Remote Mode button, point the remote controller at the AV
receiver, and operate the component.
The [DVD] and [CD] Remote Mode
buttons are preprogrammed with
remote control codes for controlling
Integra DVD players and CD players
respectively. When these buttons are
reset, the preprogrammed code is
restored.
If you want to control an Integra component by pointing
the remote controller directly at it, or you want to control
an Integra component that’s not connected via
, use
the following remote control codes:
[DVD] Remote Mode button
0627: Integra DVD player without
(default)
[CD/MD/CDR/Dock] Remote Mode button
1817: Integra CD player without
(default)
0868: Integra MD recorder without
1323: Integra CD recorder without
2990: Onkyo RI Dock without
Resetting the Remote Controller
You can reset the remote controller to its default settings.
1
While holding down the
[Receiver] Remote Mode button,
press the [L Night] button for 3
seconds.
The [Receiver] button lights up.
2
Press the [Receiver] Remote
Mode button again.
The [Receiver] button flashes twice,
indicating that it’s been reset.
Note:
If you connect an
-capable Integra MD recorder, CD
recorder, or Onkyo RI Dock to the TAPE IN/OUT or
GAME/TV jacks, for remote operation to work properly,
you must set the input display to MD, CDR, or DOCK
(see page 51).
91
Controlling Other Components—Continued
To control another component, point the remote controller at it and use the buttons explained below. (You must
select the appropriate remote control mode first.) With some AV components, certain buttons may not work as
expected, and some may not work at all.
■ Controlling a TV
■ Controlling a VCR
1
Press [TV]
first
■ Controlling a Satellite or
Cable Receiver
1
1
2
2
Press [SAT]
first
Press [VCR]
first
2
3
3
4
5
6
4
7
5
3
4
5
6
7
8
9
6
[Standby/On], TV [
]*
Sets the TV to Standby or On.
Number buttons
Sets the VCR to Standby or
On.
[Standby/On]
Sets the satellite/cable receiver
to Standby or On.
Enter numbers.
Number buttons
Number buttons
TV VOL [ ]/[ ]*
Select channels.
Enter numbers.
[CLR]
Adjusts the TV’s volume.
Cancels functions.
[CH +/–]
Selects channels on the TV.
Selects the previous channel.
[TV Input]*
Selects the TV’s VCR input.
[ ], [ ], [ ], [ ], [
Operates the VCR.
[CH +/–]
Selects channels on the VCR.
[Previous]
]
* Buttons marked with an asterisk (*) are exclusively for controlling a TV and can be used at
anytime regardless of the current remote controller mode.
92
[Standby/On]
[ ], [ ], [ ]
Pause, Play, Stop.
[ ], [ ]
Rewind and Fast forward.
[CLR]
Cancels functions.
[CH +/–]
Selects satellite/cable channels.
[Previous]
Selects the previous channel.
[Guide]
Displays the program guide.
[Enter]
Confirms the selection.
[ ]/[ ]/[ ]/[ ]
Selects menu items.
[ ], [ ], [ ], [ ], [
Operates the VCR.
]
Specifications
Amplifier Section
General
Rated Output Power (FTC)
All channels:
90 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of
0.08%
105/110 watts minimum continuous
power per channel, 8 ohm loads,
2 channels driven at 1 kHz, with a
maximum total harmonic distortion of
0.7/0.9%
110 watts minimum continuous power
per channel, 6 ohm loads, 2 channels
driven at 1 kHz with a maximum total
harmonic distortion of 0.1%
Maximum Output Power (JEITA)
7 ch u 175 W at 6 ohms, 1 kHz, 1 ch
driven
Dynamic Power
210 W + 210 W (3 :, Front)
180 W + 180 W (4 :, Front)
110 W + 110 W (8 :, Front)
THD (Total Harmonic Distortion)
0.08% (Power Rated)
0.08% (1 kHz, 1 W)
Damping Factor
60 (Front, 1 kHz, 8 :)
Input Sensitivity and Impedance
200 mV/47 k: (LINE)
Output Level and Impedance
200 mV/470 : (REC OUT)
5 Hz - 100 kHz/+1 dB - 3 dB (Direct mode)
Frequency Response
Tone Control
±10 dB, 50 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
100 dB (LINE, IHF-A)
Speaker Impedance
North American: 6 : - 16 :
Australian: 4 : - or 6 : - 16 :
Power Supply
Video Section
Input Sensitivity/Output Level and Impedance
1 Vp-p/75 : (Component and S-Video Y)
0.7 Vp-p/75 : (Component PB/CB, PR/CR)
0.28 Vp-p/75 : (S-Video C)
1 Vp-p/75 : (Composite)
Component Video Frequency Response
5 Hz - 50 MHz - 3 dB
North American: AC 120 V, 60 Hz
Australian: AC 230 V, 50 Hz
Power Consumption
North American: 6.5 A
Australian: 630 W
Dimensions (W u H u D)
435 u 172 u 391 mm
17-1/8" u 6-3/4" u 15-3/8"
Weight
North American: 11.6 kg (25.6 lbs.)
Australian: 11.8 kg (26.0 lbs.)
■ Video Inputs
HDMI
Component
S-Video
Composite
IN1, IN2
IN1, IN2, IN3
DVD, VCR/DVR, CBL/SAT, GAME/TV,
AUX
DVD, VCR/DVR, CBL/SAT, GAME/TV,
AUX
■ Video Outputs
HDMI
Component
S-Video
Composite
OUT
OUT
MONITOR OUT, VCR/DVR
MONITOR OUT, VCR/DVR
■ Audio Inputs
Digital Inputs
Analog Inputs
Multichannel Inputs
Optical: 3 (1 on Front Panel)
Coaxial: 2
DVD (MULTICHANNEL), VCR/DVR,
CBL/SAT, GAME/TV, AUX, TAPE, CD
7.1
■ Audio Outputs
Digital Outputs
Optical: 1
Analog Outputs
TAPE, VCR/DVR, ZONE2
Multichannel Pre Output
7.1 ch
Speaker Outputs
L, R, C, SL, SR, SBL, SBR,
ZONE2 (L/R)
Phones
1
■ Control Terminals
RS232
IR Input/Output
12 V Trigger Out
1
2/1
A, B, C
Tuner Section
FM Tuning Frequency Range
North American: 87.5 MHz - 107.9 MHz
Australian: 87.5 MHz - 108.0 MHz
AM Tuning Frequency Range
North American: 530 kHz - 1710 kHz
Australian: 522/530 kHz - 1611/1710 kHz
Preset Channel
40
Specifications and features are subject to change without
notice.
93
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact the dealer from whom you purchased.
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting the dealer from
whom you purchased.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [Standby/On] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
Power
Can’t turn on the AV receiver
• Make sure that the power cord is properly plugged into
the wall outlet.
• Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.
The AV receiver turns off as soon as it’s turned
on
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord
and set the volume to maximum. If the AV receiver
stays on, set the volume to minimum, disconnect the
power cord, and reconnect your speakers and input
sources. If the AV receiver turns off when you set the
volume to maximum, disconnect the power cord, and
contact the dealer from whom you purchased.
Audio
There’s no sound, or it’s very quiet
• Make sure that the digital input source is selected
properly (page 50).
• Make sure that all audio connecting plugs are pushed
in all the way (page 18).
• Make sure that the inputs and outputs of all components are connected properly (page 18).
• Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with the
metal part of each speaker terminal (page 20).
• Make sure that the input source is properly selected
(page 54).
• Make sure that the speaker cables are not shorting.
94
• Check the volume. It can be set to MIN, 1 through 99,
or MAX (page 54). The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
• If the MUTING indicator is shown on the display,
press the remote controller’s [Muting] button to
unmute the AV receiver (page 56).
• While a pair of headphones is connected to the Phones
jack, no sound is output by the speakers (page 56).
• If there’s no sound from a DVD player connected to an
HDMI IN, check the DVD player’s output settings,
and be sure to select a supported audio format.
• Check the digital audio output setting on the connected device. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• If your turntable doesn’t have a built-in phono
preamp, you must connect one between it and the AV
receiver. If your turntable uses an MC cartridge, you
must connect an MC head amp, or an MC transformer
and phono equalizer.
• Make sure that none of the connecting cables are bent,
twisted, or damaged.
• Not all listening modes use all speakers (page 64).
• Specify the speaker distances (page 70) and adjust the
individual speaker levels (page 71).
• Make sure that the speaker setup microphone is not
still connected.
Only the center speaker produces sound
• If you use the Dolby Pro Logic IIx Movie, Dolby Pro
Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio
station or mono TV program, the sound is concentrated in the center speaker.
• Make sure the speakers are configured correctly
(page 68).
The surround speakers produce no sound
• When the Stereo or Mono listening mode is selected,
the surround speakers produce no sound (page 64).
• Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
• Make sure the speakers are configured correctly
(page 68).
The center speaker produces no sound
• When the Mono or Stereo listening mode is selected,
the center speaker produces no sound (page 64).
• Make sure the speakers are configured correctly
(page 68).
Troubleshooting—Continued
The surround back speakers produce no sound
• The surround back speakers are not used with all listening modes. Select another listening mode (page 64).
• Not much sound may be produced by the surround
back speakers with some sources.
• Make sure the speakers are configured correctly
(page 68).
The DVD analog multichannel input doesn’t
work
• Check the DVD analog multichannel input connections (page 28).
• To select the DVD analog multichannel input, press
the [Multi CH] input selector button.
• Check the audio output settings on your DVD player.
The subwoofer produces no sound
• When you play source material that contains no information in the LFE channel, the subwoofer produces
no sound.
• Make sure the speakers are configured correctly
(page 68).
About DTS signals
• When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver
does not switch formats immediately, you may not
hear any sound, in which case you should stop your
player for about three seconds, and then resume playback.
• With some CD and LD players, you won’t be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesn’t recognize it as a genuine DTS signal. In such
cases, you may hear noise.
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a malfunction.
There’s no sound with a certain signal format
• Check the digital audio output setting on the connected device. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• Depending on the input signal, some listening modes
cannot be selected (pages 60-63).
Can’t select the DTS-ES Discrete/Matrix listening modes
• These modes cannot be selected when no surround
back speakers are connected, or the Zone 2 speakers
are being used.
• You can not always select all of the listening modes,
depending on the number of the speaker connected
(pages 60-63).
Can’t get 6.1/7.1 playback
• If no surround back speakers are connected, or the
Zone 2 speakers are being used, 6.1/7.1 playback is
not possible.
• You can not always select all of the listening modes,
depending on the number of the speakers connected
(pages 60-63).
The beginning of audio received by an HDMI IN
can’t be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio signals, audio output may not start immediately.
The volume cannot be set to 99
• When the levels of all speakers have been calibrated
(page 71), the maximum volume setting may change.
There’s no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 18).
• Make sure that each video component is properly connected.
• If your TV is connected to the HDMI OUT, set the
HDMI Monitor setting to Yes (page 47), and select “- -” in the “HDMI Input Setup” on page 48 to watch
composite video, S-Video, and component video
sources.
• If your TV is connected to the COMPONENT VIDEO
OUT, set the HDMI Monitor setting to No (page 47),
and select “- - -” in the “Component Video Setup” on
page 49 to watch composite video and S-Video
sources.
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
• An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
• Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD (page 67).
Video
95
Troubleshooting—Continued
• If the video source is connected to a component video
input, your TV must be connected to the COMPONENT VIDEO OUT or HDMI OUT (page 25).
• If the video source is connected to an HDMI input,
your TV must be connected to the HDMI OUT
(page 25).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
There’s no picture from a source connected to
an HDMI IN
• If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that the TV or display
does not support the current video resolution and you
need to select another resolution on your DVD player.
The onscreen menus don’t appear
• The onscreen menus may do not appear on a TV that’s
connected to the HDMI OUT. When the HDMI Monitor Out is set to No (page 47), the onscreen menus are
output at a resolution of 480i. If the onscreen menus
do not appear, set the HDMI Monitor Out to Yes
(page 47).
• Make sure that the video settings are correct (page 48).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The immediate display does not appear
• The immediate display appears on a device connected
to the COMPONENT VIDEO OUT, when the Component Video Setup (page 49) is set to “---.”
• If both of the HDMI Video Setup (page 48) and the
Component Video Setup (page 49) are set to “---,” the
immediate display is output to a device connected to
the HDMI OUT.
Tuner
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear
• Relocate your antenna.
• Move the AV receiver away from your TV or computer.
• Listen to the station in mono (page 57).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
96
Remote Controller
The remote controller doesn’t work
• Make sure that the batteries are installed with the correct polarity (page 12).
• Install new batteries. Don’t mix different types of batteries, or old and new batteries (page 12).
• Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 12).
• Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
• Make sure you’ve selected the correct remote controller mode (pages 13-16).
• When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
• Make sure you’ve entered the correct remote control
code.
• Make sure to set the same ID on both the AV receiver
and remote controller (pages 81 and 83).
Can’t control other components
• If it’s an Integra component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an
cable won’t work (page 39).
• Make sure you’ve selected the correct remote controller mode (pages 13-16).
• If you’ve connected an
-capable Integra MD
recorder, CD recorder,
Dock to the TAPE IN/
OUT jacks, or an
Dock to the GAME/TV IN
jacks, for the remote controller to work properly, you
must set the display to MD, CDR, or DOCK (pages 51
and 91).
• To control another manufacturer’s component, point
the remote controller at that component.
• To control an Integra component that’s connected via
, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 91).
• To control an Integra component that’s not connected
via
, or another manufacturer’s component, point
the remote controller at the component. Be sure to enter
the appropriate remote control code first (page 90).
Troubleshooting—Continued
Recording
Can’t record
• On your recorder, make sure the correct input is
selected (e.g., digital or analog).
Zone 2
There’s no sound
• Only components connected to analog inputs can be
played in Zone 2.
Others
The sound changes when I connect my headphones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct.
The speaker volume cannot be set as required
• When the Automatic Speaker Setup function is used,
or the volume is adjusted on the onscreen setup
menus, the maximum possible volume setting may
change.
The speaker distance cannot be set as required
• In some cases, corrected values suitable for home theater use may be set automatically.
How do I change the language of a multiplex
source
• Use the “Multiplex” setting on the “Audio Adjust”
menu to select Main or Sub (page 74).
The
functions don’t work
• To use
, you must make an
connection and an
analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 39).
The following settings can be made for the component video, S-Video, and composite video inputs
You must use the buttons on the unit to make these settings.
1. While holding down the input selector button for the
input source that you want to set, press the [Setup]
button.
2. Use the Left and Right [ ]/[ ] buttons to change
the setting.
3. Press the [Setup] button when you’ve finished.
• Video Attenuation
This setting can be made for the DVD, VCR/DVR,
CBL/SAT, GAME/TV, or AUX input.
If you have a games console connected to the component video, S-Video, or composite video input,
and the picture isn’t very clear, you can attenuate the
gain.
Video ATT:0: (default).
Video ATT:2: Gain is reduced by 2 dB.
The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded correctly.
Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby.
The functions Auto Power On/Standby and
Direct Change don’t work for components connected via
• These functions don’t work when Zone 2 is turned on.
When performing “Automatic Speaker Setup,”
the measurement fails showing the message
“Ambient noise is too high.”
• This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
97
MEMO
98
MEMO
99
Integra Division of
ONKYO U.S.A. CORPORATION
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
En
Y0704-1
SN 29344500
(C) Copyright 2007 ONKYO CORPORATION Japan. All rights reserved.
100
* 2 9 3 4 4 5 0 0 *
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising