Integra | DTR-6.2 | Owner Manual | Integra DTR-6.2 Receiver Owner Manual

Integra DTR-6.2 Receiver Owner Manual
Contents
AV Receiver
Before using
2
Facilities and connections
8
DTR-6.2
Instruction Manual
Thank you for purchasing the
AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit. Following the
instructions in this manual will enable you to obtain
optimum performance and listening enjoyment
from your new AV Receiver. Please retain this
manual for future reference.
Setup and operation
24
Remote controller
46
Appendix
61
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Important Safeguards
1. Read Instructions – All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions
should be followed.
5. Cleaning – Unplug the appliance from the wall outlet before
cleaning. The appliance should be cleaned only as recommended by the manufacturer.
6. Attachments – Do not use attachments not recommended by
the appliance manufacturer as they may cause hazards.
7. Water and Moisture – Do not use the appliance near water –for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories – Do not place the appliance on an unstable cart,
stand, tripod, bracket, or table. The appliance may fall, causing
serious injury to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the appliance.
Any mounting of the appliance should follow the
manufacturer’s instructions,
PORTABLE CART WARNING
and should use a mounting accessory recommended by the
manufacturer.
9. An appliance and cart combination should be moved with care.
Quick stops, excessive force, S3125A
and uneven surfaces may cause
the appliance and cart combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the appliance
and to protect it from overheating, and these openings must not
be blocked or covered. The openings should never be blocked
by placing the appliance on a bed, sofa, rug, or other similar
surface. The appliance should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided. There should be free space of at least 20 cm (8 in.)
and an opening behind the appliance.
11. Power Sources – The appliance should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your appliance dealer or local power company.
12. Grounding or Polarization – The appliance may be equipped
with a polarized alternating current line plug (a plug having one
blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
2
13. Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
14. Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the appliance, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See Figure 1.
15. Lightning – For added protection for the appliance during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to
the appliance due to lightning and power-line surges.
16. Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
17. Overloading – Do not overload wall outlets, extension cords,
or integral convenience receptacles as this can result in a risk
of fire or electric shock.
18. Object and Liquid Entry – Never push objects of any kind
into the appliance through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the appliance.
19. Servicing – Do not attempt to service the appliance yourself as
opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
20. Damage Requiring Service – Unplug the appliance form the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen into the
appliance,
C. If the appliance has been exposed to rain or water,
D. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the appliance to its normal operation,
E. If the appliance has been dropped or damaged in any way,
and
F. When the appliance exhibits a distinct change in performance – this indicates a need for service.
21. Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
22. Safety Check – Upon completion of any service or repairs to the
appliance, ask the service technician to perform safety checks to
determine that the appliance is in proper operation condition.
23. Wall or Ceiling Mounting – The appliance should be mounted
to a wall or ceiling only as recommended by the manufacturer.
24. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
FIGURE 1:
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Precautions
1. Warranty Claim
You can find the serial number on the rear panel of this unit. In case
of warranty claim, please report this number.
2. Recording Copyright
Recording of copyrighted material for other than personal use is
illegal without permission of the copyright holder.
3. AC Fuse
The fuse is located inside the chassis and is not user-serviceable. If power
does not come on, contact your Integra/Onkyo authorized service station.
4. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and
wipe off the dirt. Following this, dry immediately with a clean
cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish or remove
the panel lettering.
5. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.
Worldwide models are equipped with a voltage selector to conform
to local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit.
NEC – NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
For U.S. models
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
For Canadian models
NOTE:
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modele pour les Canadien
REMARQUE:
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION:
POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA
PRISE ET POUSSER JUSQU’AU FOND.
3
Contents
Before using
Connecting the AM antenna cable ................................. 22
Important Safeguards ......................................... 2
Connecting the included antennas ................................. 22
Precautions ......................................................... 3
Connecting an FM outdoor antenna ............................... 23
Contents .............................................................. 4
Connecting an AM outdoor antenna .............................. 23
Features ............................................................... 6
Directional linkage ......................................................... 23
Supplied accessories ......................................... 6
Before using this unit ......................................... 7
Installing the remote controller batteries ......................... 7
Using the remote controller .............................................. 7
Setup and operation
Speaker setup ................................................... 24
Speaker Configuration submenu .................................... 24
Speaker Distance submenu ............................................ 25
Facilities and connections
Front panel facilities ........................................... 8
Remote controller ............................................. 10
Connections ...................................................... 12
Connecting your audio components .............................. 13
Connecting your video components .............................. 14
Connect to devices with z terminals ........................... 16
Cautions regarding the AC OUTLETS connectors ....... 16
Connecting power amplifiers ......................................... 16
12V TRIGGER A, B terminals ...................................... 16
Connect to devices with multichannel output ................ 17
Plugging in the power cord to the AC INLET
receptacle ................................................................ 17
About the other settings ................................................. 26
Listening to Radio Broadcasts ........................ 27
Tuning into a radio station ............................................. 27
Listening to a stereo radio station (FM mode) .............. 27
Presetting a radio station ................................................ 28
Selecting a preset radio station ...................................... 28
Erasing a preset radio station ......................................... 28
Enjoying music or videos with the DTR-6.2 ...... 29
Basic operation ............................................................... 29
Temporarily turning off the sound ..................................... 29
Adjusting the bass and treble ......................................... 29
Listening with headphones ............................................. 29
RS 232 port ..................................................................... 17
Switching the display ..................................................... 30
Connecting speakers ....................................... 17
Adjusting the brightness of the front display ................ 30
Positioning speakers ....................................................... 17
Connecting speakers ....................................................... 18
Connecting the speaker cable ......................................... 18
Connecting a subwoofer ................................................. 18
Listening to music in the remote zone ........... 19
When using the ZONE 2 SPEAKERS terminals ........... 19
When using the ZONE 2 OUT terminals ...................... 19
Operating components not reached by the
remote controller signals (IR IN/OUT) ....... 20
Using the sleep time (remote controller only) ............... 30
Temporarily changing the speaker output levels ........... 30
Changing the audio mode ............................................... 31
Enjoying the multichannel output .................................. 31
Using listening mode ....................................... 32
Listening modes ............................................................. 32
Changing the listening mode .......................................... 33
Using Cinema Re-Equalization ...................................... 33
Setup menus ..................................................... 34
If the remote controller signal does not
reach the DTR-6.2 remote sensor ........................... 20
Navigating through the Setup menu .............................. 35
If the remote controller signal does not
1-1. Speaker Config sub-menu ....................................... 36
1. Speaker Setup menu ................................................. 36
reach other components .......................................... 20
1-2. Speaker Distance sub-menu .................................... 37
Connecting the power ...................................... 21
1-3. Level Calibration sub-menu ................................... 37
Connecting antennas ....................................... 22
Assembling the AM loop antenna .................................. 22
4
Level Calibration submenu ............................................ 26
Contents
2-1. Audio Setup sub-menu ............................................ 38
Operationing your programmed remote
controller ...................................................... 52
2-2. Video Setup sub-menu ............................................ 39
DVD MODE (DVD Player Mode) ................................ 52
2-3. Listening Mode Preset sub-menu ........................... 40
SAT MODE (Satellite Tuner Mode) .............................. 52
2-4. IntelliVolume sub-menu .......................................... 40
CABLE MODE (Cable Mode) ....................................... 52
2-5. 12V trigger sub-menu ............................................. 40
VCR MODE (VCR Mode) ............................................. 53
3. Listening Mode Setup menu ................................... 41
TV MODE (TV Mode) ................................................... 53
Description listening mode parameters ......................... 41
Programming the commands of remote
controllers for other devices into the
remote controller ......................................... 54
2. Input Setup menu ..................................................... 38
4. Preference menu ....................................................... 41
4-1. Volume Setup sub-menu ......................................... 41
4-2. Headphones Level sub-menu .................................. 42
4-3. Late Night Setup sub-menu .................................... 42
4-4. IR IN Setup sub-menu ............................................ 42
4-5. Powered Zone 2 Setup sub-menu ........................... 42
5. OSD Setup menu ...................................................... 43
5-1. OSD Setup sub-menu .............................................. 43
5-2. OSD Position sub-menu ......................................... 43
Recording .......................................................... 44
Recording the input source (REC OUT selector) .......... 44
Recording both the audio and video .............................. 44
Enjoying music in the remote zone ................ 45
Programming procedure ................................................. 54
Erasing the programmed command from one button .... 56
Erasing all the commands programmed
under a MODE button ............................................. 56
Using a Macro function .................................... 57
What is a Macro function? ............................................. 57
Programming a Macro function ..................................... 57
Running a Macro function ............................................. 57
Programming the Direct Macro function ....................... 58
Running a Direct Macro function .................................. 58
Erasing a macro from the MODE MACRO button ....... 59
Erasing a direct macro from the DIRECT MACRO button ...... 59
Selecting an input source and adjusting the
volume on the DTR-6.2 .......................................... 45
Erasing all commands and macros that have been
Selecting an input source and adjusting the
(Macro mode programming memo ............................... 60)
programmed ............................................................ 60
volume using the remote controller ........................ 45
Remote controller
Appendix
Using remote controller ................................... 46
Specifications ................................................... 61
Overview ........................................................................ 46
Troubleshooting guide ..................................... 62
Calling up a preset radio station .................................... 46
POWER .......................................................................... 62
Controlling an Integra/Onkyo cassette tape deck .......... 46
SPEAKERS .................................................................... 62
Controlling an Integra/Onkyo CD player ...................... 47
FM/AM TUNER ............................................................. 62
Controlling an Integra/Onkyo DVD player ................... 48
VIDEO and AUDIO ....................................................... 63
Controlling an Integra/Onkyo MD recorder .................. 49
REMOTE CONTROLLER ............................................ 63
SAT, CABLE, VCR, and TV MODE buttons ................ 49
OTHER ........................................................................... 63
Learning a pre-programming code ................. 50
If one of the messages shown below appears ................ 63
Learning a pre-programming code ................................. 50
Pre-programming codes ................................................. 51
5
Features
Amplifier Features
■ 5.1-Channel input
■ 100 Watts minimum of continuous RMS power
to each of the five channels into 8 Ω from 20 Hz
to 20 kHz with no more than 0.08% THD (North
American models, FTC rated)
■ 4 Assignable digital inputs (2 coaxial, 2 optical)
■ 130 Watts minimum of continuous RMS power
to each of the five channels into 6 Ω at 1 kHz
(European models, DIN)
■ 7 Sets of heavy-duty multiway speaker binding
posts (dual banana-plug compatible)
■ Wide Range Amplifier Technology (WRAT)
FM/AM Tuner Features
■ DVD-Audio Capability
■ 5 S-video inputs and 5 A/V inputs
■ Rec out selector (sound)
■ 40 FM/AM random presets
■ FM auto tuning
■ Multiroom/multisource Capability
■ Zone-2 Powered Line Out
Other Performance Features
■ State-of-the-art linear PCM 96 kHz/24-bit DACs
for all channels
■ IntelliVolume
■ Fully discrete output stages for all five channels
■ Tone control (bass, treble) for front L/R
speakers
■ 3-Mode display dimmer
■ Battery-free memory backup
■ Powerful backlit/ programmed learning remote
with macro and mode-key LEDs
Audio/Video Features
■ 12 Volt DC Trigger
■ Dolby®* Digital, DTS®, Dolby Pro Logic II
decoding
■ IR IN/OUT for custom installer
■ RS 232 Control port
■ Non-Scaling Configuration
■ 2 Component-Video Inputs/1 Output
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby
Laboratories, Inc. All rights reserved.
■ Y/C Composite signal separation
■ Cinema Re-EQTM
■ Onscreen graphical displays in 7 colors and a
superimpose mode
■ Smart Scan Navigator with LEDs
• Re-Equalization and the “Re-EQ” logo are trademarks of Lucasfilm Ltd.
Manufactured under license of Lucasfilm Ltd.
• Manufactured under license from Digital Theater Systems, Inc. US Pat.
No.5,451,942 and other worldwide patents issues and pending. “DTS”
and “DTS Digital Surround” are trademarks of Digital Theater Systems,
Inc.© 1996 Digital Theater Systems, Inc. All rights reserved.
Supplied accessories
Check that the following accessories are supplied with the DTR-6.2.
AM loop antenna × 1
Remote controller × 1
Batteries (AA, R6 or UM-3) × 2
6
FM indoor antenna × 1
(connector will vary depending
on model specifications)
Power cord × 1
Before using this unit
Installing the remote controller batteries
1. Remove the battery compartment cover by pressing
and sliding the cover.
2. Insert two AA (R6 or UM-3) batteries into the battery
compartment. Carefully follow the polarity diagram
(positive (+) and negative (–) symbols) inside the
battery compartment.
Using the remote controller
Point the remote controller toward the remote control sensor. The
STANDBY indicator lights up when the unit receives a signal from
the remote controller.
Remote control sensor
DTR-6.2
Standby indicator
3. After batteries are installed and seated correctly,
replace the compartment cover.
1
2
3
30˚
30˚
Approx. 16 feet
Notes:
• Do not mix new batteries with old batteries or different kinds of
batteries.
• To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both the batteries at the same time.
• The life of the batteries supplied is about six months but this will
vary depending on usage.
Notes:
• Place the unit away from strong light such as direct sunlight or
inverted fluorescent light which can prevent proper operation of
the remote controller.
• Using another remote controller of the same type in the same
room or using the unit near equipment which uses infrared rays
may cause operational interference.
• Do not put objects on the remote controller. Its buttons may be
pressed by mistake and drain the batteries.
• Make sure the audio rack doors do not have colored glass.
Placing the unit behind such doors may prevent proper remote
controller operation.
• If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.
7
Front panel facilities
Here is an explanation of the controls and displays on the front panel of the DTR-6.2.
Front panel
1 2
3
4 5 6 7
See illustration below
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
8
CH Level
Master Volume
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
9
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
0
Video 4
Tape
FM
AM
Phono
B
A
D
E
Treble
CD
C
GH
F
DSP/ Mode ADJ
Setup
Return
Push To Enter
Display
Dimmer
FM Mode
Preset Memory
I J K L
Tuning
Preset
M
N
Smart Scan Navigator
Front panel display
Rec out indicator
Zone 2 indicator
8
Sleep indicator
Listening mode or digital input
format indicators
Multi fanction display
Tuning indicators
Front panel facilities
For operational instructions, see page indicated in brackets [ ].
Power switch [21]
Turns on and off the main power supply for the DTR-6.2.
Standby indicator [7, 21]
Lights when the DTR-6.2 is in the standby state and flashes when a
signal is received from the remote controller.
Standby/On button [21]
Press to turn on the DTR-6.2 when in the standby state. Press again
to return the DTR-6.2 to the standby state.
Rec Out button [44]
Press the Rec Out button to output the audio signals to a recording
component for recording purposes.
Zone 2 button [45] and indicator
Press the Zone 2 button to enjoy the output from the DTR-6.2 in a
different room, which is referred to as a remote zone (Zone 2).
ZONE 2 indicator lights when a signal is output to the remote zone
(Zone 2). When the ZONE 2 indicator is off, then either output to the
remote zone is turned off or Rec Out is selected.
Zone 2 Level button [45]
Press to enter the mode for adjusting the volume in the remote zone
(Zone 2).
Remote control sensor [7]
Smart Scan Navigator jog dial and indicators [2426, 28, 30, 31, 33, 35, 45]
Used to make settings in the Setup menu, change listening mode
settings, and more.
Setup button [24-26, 35]
Press to bring up the Setup menu. The OSD menu will appear on the
TV monitor as well as the front display on the DTR-6.2.
Return button [24-26, 35]
Press to exit the Main menu level or go back one level up.
Display button [30]
The DISPLAY button is used to display information about the
current input source signal. Each time you press the display button,
the screen changes to show you different information concerning the
input signal.
Dimmer button [30]
Press to set the brightness of the front display. There are 3 settings
available: normal, dark, and very dark.
CH Level button [30]
Press to select the channel whose level is to be adjusted.
FM Mode button [27]
If you are listening to an FM radio station in stereo and the sound
cuts out or there is a great deal of noise, switch from STEREO to
MONO. Each time this button is pressed, the AUTO indication
flashes and the stereo mode changes from AUTO to MONO and vice
versa. This button also turns on and off the FM MUTE.
Master Volume dial [29, 31]
The Master Volume dial is used to control the volume for the main
zone. The volume for the remote zone (Zone 2) is independent.
Preset Memory button [28]
This button is used to assign the radio station that is currently tuned
in to a preset channel or delete a previously preset station.
Phones jack [29]
This is a standard stereo jack for connecting stereo headphones.
Audio Selector button [31]
This button is used to select the type of audio input signal. Each time
pressed, the setting cycles from “AUTO” → “Multich” → “Analog”
and back.
Tuning / buttons [27]
Use these buttons to change the tuner frequency. The tuner
frequency is displayed in the front display and it can be changed in
50 kHz increments for FM and 10 kHz increments for AM.
When FM is selected, you can hold down one of the tuning buttons
and then release it to activate the auto-search feature. It will search
for a station in the direction of the button you pressed and stop
when it tunes into one.
Input source buttons (DVD, Video 1–4, Tape, FM,
AM, Phono, and CD) [27, 28, 29, 44, 45]
These buttons are used to select the input source for the main zone.
To select the input source for the remote zone (Zone 2) or recording
out (Rec Out), first press the Zone 2 or Rec Out button, and then the
desired input source button.
Preset / buttons [28]
When AM or FM is selected as the input source, press one of these
buttons to jump to a radio station that you preset using the Preset
Memory button. Pressing the right button moves from the most
recently preset station to older ones, and pressing the left button
moves in the reverse order.
Bass dial [31]
Boosts or cuts the bass response. Bass adjustment is effective only
for the front L/R speakers and headphones.
Treble dial [31]
Boosts or cuts the treble response. Treble adjustment is effective
only for the front L/R speakers and headphones.
Front display
9
Remote controller
SEND/LEARN indicator [50, 54, 56]
This indicator acts as a guide when commands are programmed into
or sent by the remote controller. It also warns the user when an error
is made or battery power is low.
1
ON/STDBY button [21, 47-50, 52, 53, 60]
ON: Turns on the DTR-6.2.
STDBY: Places the DTR-6.2 in the standby state.
Be aware that pressing the STDBY button only places the DTR-6.2
in standby and does not turn the power completely off.
2
3
4
D
E
5
6
7
9
I
8
0
F
G
H
J
SLEEP button [30]
Sets the sleep function.
The SLEEP button enables you to set the DTR-6.2 to turn off
automatically after a specified time period.
DIRECT MACRO button [58, 59]
For executing and programming the Direct Macro function.
MODE buttons and indicators [21, 28, 46-59]
For selecting the component to be operated by the remote controller.
When a MODE button is pressed, it will light green for 8 seconds.
The selected MODE button will also light whenever any other
operation button is pressed to tell you which mode the remote
controller is in.
RETURN button [35, 48]
For entering the selected setting and returning to the previous menu.
A
CH/DISC
button [28, 46-48, 52, 53]
When in the RCVR mode, for selecting a tuner preset channel.
For selecting the disc to be played back for components with disc
changers when in the DVD or CD modes.
B
CH SEL/TOP MENU button
CH SEL: For selecting the speaker for level adjustment when in the
RCVR mode. Used together with the LEVEL / buttons. [30]
TOP MENU: When in the DVD mode, for displaying the menu
screen(s) recorded on DVD media. [48]
C
K
HOME THEATER CONTROLLER
RC-441M
AUDIO/A/TV/VCR button
AUDIO/A: For selecting the audio input signal. The setting changes
from “AUTO” to “Multich” to “Analog” and back each time this
button is pressed. [31, 48]
TV/VCR: Must be preprogrammed for use in the TV and VCR
modes. [53]
LEVEL /ANGLE and LEVEL /SUBTITLE buttons
LEVEL / : Select the speaker whose volume is to be adjusted
using the CH SEL button and adjust the volume using the LEVEL /
buttons in the RCVR mode. [30]
ANGLE: When in the DVD mode, for selecting a camera angle
when a DVD-Video is recorded with multiple angle playback. [48]
SUBTITLE: When in the DVD mode, for selecting one of the
subtitle languages recorded on a DVD-Video. [48]
CD/TAPE/DVD/MD operation buttons [46-48, 53]
For operating Integra/Onkyo components connected to the DTR-6.2.
10
Remote controller
INPUT SELECTOR buttons [28, 29, 45, 46, 49]
Selects an input source.
Same as the input selector buttons on front panel of the DTR-6.2.
The input source for each buttons is given here. DVD:DVD, CD:CD,
V1:Video1, V2:Video2, V3:Video3, V4:Video4, T1:Tape, T2:Not
used with the DTR-6.2, TUN:FM/AM, PH:Phono.
Numeric key/Listening mode selector/SP A, B/
Re-EQ/DISPLAY/DIMMER buttons
1 to 9, +10, --/---, 0: For entering the number of a track. [47-50, 52,
53]
STEREO, DIRECT, DSP / , SURR, A.ST: You can select a
listening mode. [33]
Re-EQ: Depending on the listening mode, you can turn the cinema
re-equalization function on or off. [33]
SP A, SP B: Not used with the DTR-6.2.
DISPLAY: For changing the display in the front display. [30, 50]
DIMMER: Adjusts the display brightness.
There are three settings available: normal, dark and very dark. [30]
ZONE 2/SEARCH/ENTER button
ZONE 2: When in the RCVR mode, press this button to perform
operations on the remote zone (Zone 2). [45]
SEARCH: When in the DVD mode, for finding the specific section
on a disc where you want to start playback. [48]
ENTER: When in the MD mode, for confirming the selection. [49,
52-54, 56, 60]
LIGHT button
For illuminating the buttons of the remote controller.
This is button is useful when using the remote controller in dark
locations. When pressed, the buttons on the remote controller light
green.
The button for the mode currently selected lights brighter than the
rest.
MODE MACRO button [57, 59]
For executing and programming the Macro function.
SETUP button [35]
For displaying and quitting the Setup menu.
ENTER/cursor button [35, 48]
When selecting items in the Setup menu, press the upper and lower
portions to select item, press the right and left portions to select
parameter values or modes, and press ENTER to select item.
VOL
button [29, 31, 46-49, 52, 53]
For adjusting the volume.
TEST/MENU button
TEST: Outputs a test tone for setting speaker levels.
Use this button in conjunction with the LEVEL / and CH SEL
buttons to calibrate the speakers levels without entering the Setup
menu. When TEST button is pressed, the test noise (pink noise) is
output. Use the LEVEL / buttons to increase or decrease the
sound level. Use the CH SEL button to change from speaker to
speaker. For a more detailed explanation of how to calibrate the
speaker levels, see page 26.
MENU: When in the DVD mode, this button displays the DVD
menu. [48, 52]
MUTING/M button [29, 46-49, 52, 53]
Activates the mute function.
11
Connections
Here is explanation of how to connect the main components to the
DTR-6.2 in the standard manner. There are many ways that any one
component can be connected, and it is up to you to decide which
method best fits your situation. The directions given here are only
one option and should only be thought of as such. It is best to fully
understand the nature of each connector and terminal as well as each
of your components and their features to ascertain which method of
connection is best.
• Be sure to always refer to the instructions that came with the
component that you are connecting.
• Do not plug in the power cord until all connections have been
made.
• For input jacks, red connectors (marked R) are used for the
right channel, white connectors (marked L) are used for the
left channel, and yellow connectors (marked V) are used for
video connection.
• Do not bind audio/video connection cables with power cords
and speaker cables. Doing so may adversely affect the
picture and sound quality.
• When using the digital inputs, make sure to also connect the
analog connections whenever possible.
• Insert all plugs and connectors securely. Improper
connections can result in noise, poor performance, or
damage to the equipment.
Improper connection
Inserted completely
• When using one of the optical input jacks, remove the
protective cap and keep it safely. When the jack is not
used, replace the protective cap.
• When using an optical input jack, always use an optical
fiber cable.
Optical digital input terminal
An optical digital input terminal is equipped
with a protection cap. When connecting,
remove this cap. When not using, put the
cap back on the terminal.
Connecting antennas [22, 23]
Connect to devices with z
terminals [16]
Connecting your video
components [14, 15]
Cautions regarding the AC
OUTLETS connectors [16]
12V TRIGGER A, B terminals
[17]
12 V
TRIGGER
ANTENNA
Connecting speakers [17-19]
FRONT
SPEAKERS
COMPONENT VIDEO
Y
PB
PR
Y
PB
PR
Y
PB
PR
SURROUND
SPEAKERS
CENTER
SPEAKER
L
R
L
R
A
AM
INPUT 1
OUTPUT
IN
OUT
IN
OUT
INPUT 2
IN
IN
IN
VIDEO
B
MONITOR
OUT
FM
75
DVD
VIDEO 1
VIDEO 2
VIDEO 3 VIDEO 4
AC
OUTLETS
REMOTE
CONTROL
AC 120 V 60 Hz
SWITCHED
TOTAL 120 W
1 A MAX.
S VIDEO
AV RECEIVER
PHONO
CD
OUT
TAPE
ZONE 2
PRE OUT
IN
L
L
R
R
MODEL NO. DTR-6.2
ZONE 2
SPEAKERS
FRONT
L
SURR
CENTER
OPTICAL
1
1
IN
RS 232
2
R
SUBWOOFER
PRE OUT
MULTI
CHANNEL INPUT
Connecting a
subwoofer [18]
OUT
L
R
CAUTION:
CENTER
1
2
6 OHMS
MIN.
/ SPEAKER
4 OHMS
MIN.
/ SPEAKER
IMPEDANCE SELECTOR
DIGITAL INPUT
RS232 port [17]
Connecting power amplifiers [16]
Operating components
not reached by the remote
controller signals [20]
Default setting
Input source
DVD
Video 1
Video 2
Video 3
Video 4
Tape
FM
AM
Phono
CD
Digital input
COAX 1
COAX 2
---OPT 2
-------
Plugging in the power cord to
the AC INLET receptacle [17]
Connecting the remote
zone speakers [19]
Component video
INPUT 1
INPUT 2
INPUT 1
INPUT 1
INPUT 1
Multichannel
Yes
No
No
No
No
No
---OPT 1
COAX: Coaxial OPT: Optical ----: No setting
12
AC INLET
SEE INSTRUCTION MANUAL
FOR CORRECT SETTING.
SET BEFORE POWER ON
SUB
WOOFER
Connect to devices with
multichannel output [17]
Connecting your
audio components
[13]
SURR
IR
COAXIAL
2
GND
L
R
PRE OUT
FRONT
No
No
: Not applicable
Connections
: Signal flow
Audio connection cable
Analog audio output
L(White)
L
R(Red)
R
L (White)
R (Red)
2. CD player
(CD)
12 V
TRIGGER
ANTENNA
Digital audio output (optical)
COMPONE
Y
PB
PR
Y
OUT
IN
A
AM
INP
OUTPUT
IN
Analog audio output
MONITOR
OUT
FM
75
PHONO
R (Red)
DVD
VIDEO 1
REMOTE
CONTROL
L (White)
1. Turntable
(PHONO)
O
B
CD
OUT
TAPE
IN
L
R
Ground wire (earth)
FRONT
L
SURR
CENTER
OPTICAL
1
COAXIAL
2
GND
Analog audio input
2
R
SUBWOOFER
L (White)
3. Tape deck, MD recorder,
DAT deck, CD recorder,
(TAPE)
1
PRE OUT
MULTI
CHANNEL INPUT
SUB
WOOFER
DIGITAL INPUT
R (Red)
L (White)
R (Red)
Analog audio output
Connecting your audio components
Below is an example of how you can connect your audio
components to the DTR-6.2. Refer to the diagram above for the
following connection examples.
1. Connecting a turntable (PHONO)
Using an RCA-type audio connection cable, connect the output
terminal on the turntable to the PHONO input jacks on the DTR-6.2.
Make sure that you properly connect the left channel to the L jack
and the right channel to the R jack.
Note:
The DTR-6.2 is designed for use with moving magnet cartridges.
For proper operation, connect a ground (or earth) wire to the GND
terminal. For some turntables, however, connecting the ground wire
may cause increased noise, and in such a case, a ground wire is not
necessary and should not be connected.
2. Connecting a compact disc player (CD)
Using an RCA-type audio connection cable, connect the output
terminal on the compact disc player to the CD input jacks on the
DTR-6.2. Make sure that you properly connect the left channel to the
L jack and the right channel to the R jack.
If the compact disc player has a digital output jack as well, be sure to
also connect it to either a DIGITAL INPUT (COAXIAL) or
DIGITAL INPUT (OPTICAL) jack on the DTR-6.2 depending on
the type of connector on the compact disc player.
With the initial settings of the DTR-6.2, the CD input source is
set for digital input at the OPTICAL 1 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).
3. Connecting a cassette tape deck, MD recorder, DAT
deck, or CD recorder (TAPE)
Using an RCA-type audio connection cable, connect the output
terminals (PLAY) of the device to the TAPE IN jacks on the DTR6.2 and the input terminals (REC) to the TAPE OUT jacks. Make
sure that you properly connect the left channel to the L jack and the
right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the DTR-6.2 depending on the type of
connector on the device.
With the initial settings of the DTR-6.2, the TAPE input source is set
for no digital input.
If you connect the device to the DIGITAL INPUT terminal, then this
input source must be set for digital input at the Setup menu: Input
Setup → Audio Setup → Digital Input(see pages 26, 38).
13
Connections
CR/PR
Y
CB/PB
Component video output
CB/PB
COMPONENT VIDEO
Y
PB
Y
PR
PB
Y
PR
PB
Component video output
PR
CR/PR
Y
INPUT 1
OUTPUT
OUT
IN
Video output
IN
INPUT 2
OUT
IN
IN
V
IN
Video output
VIDEO
MONITOR
OUT
4. DVD player
(DVD)
VIDEO 1
DVD
VIDEO 2
S video
VIDEO 3 VIDEO 4
S video output
S VIDEO
TAPE
L (White)
ZONE 2
PRE OUT
IN
Analog audio output
L
S video output
L (White)
R (Red)
R
CENTER
Analog audio output
OPTICAL
1
R (Red)
IR
COAXIAL
2
1
Digital audio output (Coaxial)
Digital audio output
(Coaxial)
IN
RS 232
2
7. DVD recorder or
other digital video
recording device (VIDEO 1)
OUT
SUB
WOOFER
DIGITAL INPUT
UT
Video input
S video input
: Signal flow
R (Red)
Analog audio input
L (White)
Audio connection cable
Left (White)
Video connection cable
Component video connection cable
L
S video connection cable
CR/PR
CR/PR
CB/PB
CB/PB
Y
Right (Red)
Y
R
Component video input
CR/PR
Video output
CB/PB
COMPONENT VIDEO
Y
8. TV monitor or Projector
(MONITOR OUT)
PB
PR
Y
PB
PR
Y
PB
PR
Y
S video output
INPUT 1
OUTPUT
IN
OUT
IN
OUT
INPUT 2
IN
IN
IN
Video input
S video input
VIDEO
MONITOR
OUT
VIDEO 1
DVD
VIDEO 2
S VIDEO
Video input
TAPE
S video input
L (White)
VIDEO 3 VIDEO 4
R (Red)
9. Settop box or
Video camera, etc.
(VIDEO 4)
Analog audio output
ZONE 2
PRE OUT
IN
L
Video output
R
S video output
L (White)
Analog audio input
CENTER
5. VCR
(VIDEO 2)
OPTICAL
1
R (Red)
Video output
IR
COAXIAL
2
1
2
RS 232
IN
6. Satellite tuner or TV
(VIDEO 3)
OUT
L (White)
SUB
WOOFER
UT
S video output
DIGITAL INPUT
R (Red)
Analog audio output
R (Red)
Analog audio output
L (White)
Digital audio output (optical)
Connecting your video components
Below is an example of how you can connect your video
components to the DTR-6.2. Refer to the diagram above for the
following connection examples.
The flow of the video signals is as follows:
• The signal that comes in from VIDEO IN is sent to VIDEO OUT
and S VIDEO OUT.
• The signal that comes in from S VIDEO IN is sent to S VIDEO
OUT and VIDEO OUT.
• The signal that comes in from COMPONENT VIDEO IN is only
sent to COMPONENT VIDEO OUT.
14
4. Connecting a DVD player (DVD)
If the device is equipped with an S video output terminal, connect it
to the DVD S VIDEO IN terminal with an S video cable. If it does
not have an S video output terminal, connect its video output
terminal to the DVD VIDEO IN terminal using an RCA-type video
connection cable. You do not need to connect to both the DVD S
VIDEO IN and DVD VIDEO IN terminals. If the device has
component video outputs, connect them to one of the
COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the DVD input source is
set for the COMPONENT VIDEO INPUT 1 jack.
Connections
If the video connection is made at COMPONENT VIDEO INPUT 2,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the device to the audio DVD IN jacks on the
DTR-6.2. Make sure that you properly connect the left channel to the
L jack and the right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the DTR-6.2 depending on the type of
connector on the DVD player.
With the initial settings of the DTR-6.2, the DVD input source is
set for digital input at the COAXIAL 1 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).
5. Connecting a video cassette recorder (VIDEO 2)
If the video cassette recorder is equipped with an S video output
terminal, connect it to the S VIDEO 2 IN terminal with an S video
cable. If it does not have an S video output terminal, connect its
video output terminal to the VIDEO 2 IN terminal using an RCAtype video connection cable. You do not need to connect to both the
S VIDEO 2 IN and VIDEO 2 IN terminals. If the video cassette
recorder has component video outputs, connect them to one of the
COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the VIDEO 2 input
source is set for the COMPONENT VIDEO INPUT 1 jack.
If the video connection is made at COMPONENT VIDEO INPUT 2,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the video cassette recorder to the same VIDEO 2
IN audio jacks on the DTR-6.2 and audio input terminal to the
VIDEO 2 OUT audio jacks. Make sure that you properly connect the
left channel to the L jack and the right channel to the R jack.
6. Connecting a satellite tuner or television (VIDEO 3)
If the satellite tuner or television is equipped with an S video output
terminal, connect it to the S VIDEO 3 IN terminal with an S video
cable. If it does not have an S video output terminal, connect its
video output terminal to the VIDEO 3 IN terminal using an RCAtype video connection cable. You do not need to connect to both the
S VIDEO 3 IN and VIDEO 3 IN terminals. If the satellite tuner or
television has component video outputs, connect them to one of the
COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the VIDEO 3 input
source is set for the COMPONENT VIDEO INPUT 1 jack.
If the video connection is made at COMPONENT VIDEO INPUT
2, this must be changed at the Setup menu: Input Setup → Video
Setup → Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the satellite tuner or television to the same
VIDEO 3 IN audio jacks on the DTR-6.2. Make sure that you
properly connect the left channel to the L jack and the right channel
to the R jack.
If the satellite tuner or television has a digital output jack as well, be
sure to also connect it to either a DIGITAL INPUT (COAXIAL) or
DIGITAL INPUT (OPTICAL) jack on the DTR-6.2 depending on
the type of connector on the set top box or television.
With the initial settings of the DTR-6.2, the VIDEO 3 input
source is set for digital input at the OPTICAL 2 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).
7. Connecting a DVD recorder or other digital video
recording device (VIDEO 1)
If the device is equipped with an S video output terminal, connect it
to the S VIDEO 1 IN terminal with an S video cable. If it does not
have an S video output terminal, connect its video output terminal to
the VIDEO 1 IN terminal using an RCA-type video connection
cable. You do not need to connect to both the S VIDEO 1 IN and
VIDEO 1 IN terminals. If the device has component video outputs,
connect them to one of the COMPONENT VIDEO INPUT jacks.
With the initial settings of the DTR-6.2, the VIDEO 1 input
source is set for the COMPONENT VIDEO INPUT 2 jack.
If the video connection is made at COMPONENT VIDEO INPUT 1,
this must be changed at the Setup menu: Input Setup → Video Setup
→ Component Video (see pages 26, 38).
Using an RCA-type audio connection cable, connect the audio
output terminal on the device to the same VIDEO 1 IN audio jacks
on the DTR-6.2 and audio input terminal to the VIDEO 1 OUT audio
jacks. Make sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the DTR-6.2 depending on the type of
connector on the device.
With the initial settings of the DTR-6.2, the VIDEO 1 input
source is set for digital input at the COAXIAL 2 jack.
If the digital connection is made at a different jack, this must be
changed at the Setup menu: Input Setup → Audio Setup → Digital
Input (see pages 26, 38).
8. Connecting a television monitor or projector
(MONITOR OUT)
The DTR-6.2 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit. Since both the signal from the S VIDEO
and VIDEO inputs are output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
If the monitor or projector is equipped with an S video output
terminal, connect it to the MONITOR OUT S VIDEO terminal with
an S video cable. If it does not have an S video output terminal,
connect its video output terminal to the MONITOR OUT VIDEO
terminal using an RCA-type video connection cable. You do not
need to connect to both the MONITOR OUT S VIDEO and
MONITOR OUT VIDEO terminals. If the device has component
video inputs, connect them to the COMPONENT VIDEO OUTPUT
jacks.
Caution:
Note that the Setup menu will only be displayed on the monitor
connected to MONITOR OUT and not those connected to the
COMPONENT VIDEO OUTPUT jacks.
9. Connecting settop box or video camera, etc.
(VIDEO 4)
If the device is equipped with an S video output terminal, connect it
to the S VIDEO 4 IN terminal with an S video cable. If it does not
have an S video output terminal, connect its video output terminal to
the VIDEO 4 IN terminal using an RCA-type video connection
cable. You do not need to connect to both the S VIDEO 4 IN and
VIDEO 4 IN terminals.
15
Connections
Connect to devices with z terminals
The z terminal on the DTR-6.2 is for connecting other Integra/
Onkyo components equipped with the same z terminal. When a
component are z-connected, you can point the remote controller
supplied with the DTR-6.2 at the sensor on the DTR-6.2 and operate
that component without having to switch remote controllers.
In addition, by connecting components to the z terminal, you can
also perform the system operations given below.
Power on/ready function
When the DTR-6.2 is in the standby state, if an z-connected
component is turned on, then the DTR-6.2 also turns on and the input
source selected at the DTR-6.2 automatically switches to that
component.
If the power cord for an z-connected component is connected to
the AC OUTLET on the DTR-6.2, or if the DTR-6.2 is turned on,
this function will not work. Also, if you are using the DTR-6.2 for
the remote zone (Zone 2), this function will not work.
Cautions regarding the AC OUTLETS
connectors
The DTR-6.2 is supplied with AC mains outlets for connecting the
power cords from other devices so that their power is supplied
through the DTR-6.2. By doing this, you can use the Standby/On
button on the DTR-6.2 to turn on and off the connected devices as
well.
Caution:
Make sure that the total capacity of the other components connected
to this unit does not exceed the capacity that is printed on the rear
panel (e.g., 120 watts).
Direct change function
When the play button is pressed at an z-connected component, the
input source selected at the DTR-6.2 automatically changes to that
component. However, if you are using the DTR-6.2 for the remote
zone (Zone 2), this function will not work.
Power off function
When the DTR-6.2 is placed in the standby state, all z-connected
components are also automatically put into the standby state.
CAUTION
If an MD recorder is connected to the TAPE jack on the DTR-6.2,
switch the Input Selector from Tape to MD (see page 21).
AC
OUTLETS
AC 120 V 60 Hz
SWITCHED
TOTAL 120 W
1 A MAX.
Connecting power amplifiers
Using auxiliary power amplifiers allows you to listen at louder
volumes than with the DTR-6.2 alone. If power amplifiers are used,
connect each speaker to the corresponding power amplifier.
L (White)
DTR-6.2
REMOTE
CONTROL
Front input
R (Red)
z connector
PRE OUT
FRONT
SURR
CENTER
L
1
R
2
R (Red)
Surround input
L (White)
Center input
Ex: Integra/Onkyo CD player
z connector
1.
2.
3.
4.
5.
Power amplifier
Ex: Integra/Onkyo cassette
tape deck
To connect components using the z terminal, simply connect a
remote control cable from this z terminal to the z terminal of the
other component. An z remote control cable with a 1/8-inch (3.5mm) miniature two-conductor plug comes with every cassette tape
deck, compact disc player, MD recorder, and DVD player that has an
z terminal.
• For remote control operation, the audio connection cables must
also be connected.
• The RC-441M remote controller does not support turntables.
• If a component has two z terminals, you can use either one to
connect to the DTR-6.2. The other one can be used to daisy chain
with another component.
• With Integra/Onkyo DVD players, you can enter the preprogram code so that you can operate the DVD player directly
with the remote controller without connecting the z terminals
(see page 50).
16
1
2
3
4
Front left speaker
Front right speaker
Surround left speaker
Surround right speaker
Center speaker
5
12V TRIGGER A, B terminals
These terminals are provided so that you can use the operation of the
DTR-6.2 control the operation of another externally connected
device. Connect the component to this 1/8-inch mini-jack terminal
and when the set input source is selected, the device will turn on. Set
the 12V TRIGGER terminal using the Setup menu: Input setup →
12V trigger (see page 40).
Connections
Connect to devices with multichannel output
By connecting a DVD player, MPEG decoder, or other component that has a multi channel port, you can playback the audio with 5.1 channel
output. So, be sure to prepare a cable that can properly connect the DTR-6.2 to the peripheral device.
Center output
L (White)
Front output
DVD Player/MPEG decoder
FRONT
R (Red)
L
SURR
CENTER
GND
R (Red)
R
SUBWOOFER
Surround output
PRE OUT
MULTI
CHANNEL INPUT
SUB
WOOFER
L (White)
Subwoofer output
Plugging in the power cord to the AC INLET
receptacle
Plug the supplied power cord into this AC INLET and then into the
power outlet on the wall.
• Do not use a power cord other than the one supplied with the
DTR-6.2. The power cord supplied is designed for use with the
DTR-6.2 and should not be used with any other adevice.
• Never have the power cord disconnected from the DTR-6.2
while the other end is plugged into the wall outlet. Doing so may
cause an electric shock. Always connect by plugging into the
wall outlet last and disconnect by unplugging from the wall
outlet first.
AC INLET
RS 232 port
Power cord
(supplied)
To an AC
wall outlet
The RS 232 port is to be used in conjunction with an external
controller to control the operation of the DTR-6.2 by using an
external device.
Connecting speakers
Positioning speakers
Speaker placement plays an important role in the reproduction of
Surround sound. The placement of the speakers varies depending on
the size of the room and the wall coverings used in the room. The
illustration shows an example of a layout for standard speaker
placement. Refer to this example when you position the speakers in
order to experience the best of Surround sound.
Standard speaker placement
For ideal Surround effects, all speakers should be installed. If a
center speaker or subwoofer is not connected, the sound from the
unused channel is properly distributed to the connected speakers in
order to produce the best Surround sound possible.
Front: The left, right, and center speakers should face the seated
listener and be placed at ear level. The center speaker produces a
richer sound image by enhancing the perception of the sound’s
source and movement.
Surround: Place the left and right Surround speakers 3 feet (1
meter) above the listener’s ear level and facing toward the sides of
the room, making sure that the listener is within the speakers’ dispersion angle. These speakers produce the feel of a moving sound
while creating the sensation of being in the middle of the action.
Subwoofer: Install a subwoofer with a built-in power amplifier for
powerful bass sounds. The placement of the subwoofer does not
affect the final quality of the sound image too much, so you can
install it with the room layout in mind.
Refer to the speaker’s instruction manual for more details.
TV or Screen
Front
left
speaker
Subwoofer
Center
speaker
Surround
left
speaker
Front
right
speaker
Surround
right
speaker
Listener
17
Connecting speakers
Front right
speaker
12 V
TRIGGER
ANTENNA
Front left
speaker
FRONT
SPEAKERS
COMPONENT VIDEO
Y
PB
Y
PR
PB
Y
PR
PB
Surround right
speaker
PR
SURROUND
SPEAKERS
CENTER
SPEAKER
L
R
Surround left
speaker
L
R
A
AM
INPUT 1
OUTPUT
IN
OUT
IN
OUT
INPUT 2
IN
IN
IN
VIDEO
B
MONITOR
OUT
FM
75
DVD
VIDEO 1
VIDEO 2
VIDEO 3 VIDEO 4
AC
OUTLETS
REMOTE
CONTROL
AC 120 V 60 Hz
SWITCHED
TOTAL 120 W
1 A MAX.
S VIDEO
AV RECEIVER
PHONO
CD
OUT
TAPE
ZONE 2
PRE OUT
IN
L
MODEL NO. DTR-6.2
ZONE 2
SPEAKERS
L
R
PRE OUT
FRONT
L
SURR
CENTER
OPTICAL
1
2
1
GND
IN
RS 232
2
R
SUBWOOFER
PRE OUT
MULTI
CHANNEL INPUT
SURR
CAUTION:
CENTER
OUT
L
1
R
6 OHMS
MIN.
/ SPEAKER
2
SUB
WOOFER
AC INLET
SEE INSTRUCTION MANUAL
FOR CORRECT SETTING.
IR
COAXIAL
L
R
R
FRONT
4 OHMS
MIN.
/ SPEAKER
IMPEDANCE SELECTOR
DIGITAL INPUT
Subwoofer
Connecting speakers
Make the connections while referring to the explanations on the next
page.
1. Check the impedance of the speakers you are
connecting.
The DTR-6.2 requires speakers with an impedance of 4 Ω or
greater. Connecting speakers with an impedance of less than 4 Ω
may damage the DTR-6.2.
2. Set the IMPEDANCE SELECTOR switch according to
the impedance of the speakers being connected.
If all speakers have an impedance of 6 Ω or greater, slide the
IMPEDANCE SELECTOR switch to the left (6 OHMS MIN./
SPEAKER). If one or more speakers have an impedance of less
than 6 Ω, slide the IMPEDANCE SELECTOR switch to the
right (4 OHMS MIN./SPEAKER).
Center
speaker
• Be sure to connect the positive and negative cables for the
speakers properly. If they are mixed up, the left and right signals
will be reversed and the audio will sound unnatural.
• Do not connect more than one speaker cable to one speaker
terminal. Doing so may damage the DTR-6.2.
Connecting the speaker cable
1. Strip away 5/8 inch of wire insulation.
2. Twist wire ends very tight.
3. Unscrew
4. Insert wire
5. Screw
1
6 OHMS
MIN.
/ SPEAKER
6 OHMS
MIN.
/ SPEAKER
4 OHMS
MIN.
/ SPEAKER
4 OHMS
MIN.
/ SPEAKER
SET BEFORE POWER ON
SET BEFORE POWER ON
IMPEDANCE SELECTOR
IMPEDANCE SELECTOR
4 Ω or above/speaker
5/8"
6 Ω or above/speaker
Notes:
• The power to the DTR-6.2 must not be turned on when changing
the IMPEDANCE SELECTOR setting.
• When you are using only one speaker
or when you wish to listen to
monaural (mono) sound, a single
speaker should never be connected in
parallel to both the right and leftchannel terminals simultaneously.
3
4
5
NO!
+ – – +
R
L
• To prevent damage to circuitry,
never short-circuit the positive (+)
and negative (–) speaker wire.
NO!
18
2
+ – – +
R
L
Connecting a subwoofer
Use the PRE OUT SUBWOOFER jack to connect a subwoofer with
a built-in power amplifier. If your subwoofer does not have a built-in
amplifier, connect an amplifier to the PRE OUT SUBWOOFER jack
and the subwoofer to the amplifier.
Listening to music in the remote zone
When using the ZONE 2 SPEAKERS terminals
Connect the speaker cables from the speakres in the remote zone
(Zone 2) speaker terminals on the DTR-6.2.
With this connection, select “Activated” for the Preference →
Powered Zone 2 Setup setting in the Setup menu.
When using the ZONE 2 OUT terminals
The ZONE 2 OUT terminal is a constant output. Connect to the
LINE input of the amplifier (CD, tape, etc.). Adjust the volume
with the amplifier connected to the ZONE 2 OUT terminal.
1. Connect the DTR-6.2 to the amplifier for the remote
zone.
Remote Zone (Zone 2)
Zone 2
Right
speaker
Zone 2
Left
speaker
2. Connect the remote zone speaker cables to the
speaker terminals on the amplifier.
Adjust the volume level at the amplifier.
Remote Zone (Zone 2)
Zone 2 Left
speaker
Zone 2 Right
speaker
ZONE 2
SPEAKERS
Zone 2 amplifier
R
L
CAUTION:
SEE INSTRUCTION MANUAL
FOR CORRECT SETTING.
DTR-6.2
Main room
L (White)
Note:
• It is important to be aware of the speakerimpedance (see
previous page).
• When set to “Activated,” the following limitations will be
applied, so whenever you are not using the remote zone (Zone
2), be sure to return the setting to “Not Activated.”
- You can only use the Stereo and Direct listening modes in the
main room.
- When listening to a multi-channel input source, no sound is
output from the left and right surround speakers.
- You cannot use the Rec Out function.
ZONE 2
PRE OUT
L
R
R (Red)
Main room
DTR-6.2
19
Operating components not reached by the
remote controller signals (IR IN/OUT)
The following equipment (sold separately) is essential for
operation:
• Onkyo’s Multi-Room System kits (IR Remote Controller
Extension System), or
• Multiroom A/V distribution and control systems from Niles®
and Xantech® to name a few
Make connection as shown below. Do not plug the equipment into
the power source until the connection is complete.
from connecting block
Mini plug cable
If the remote controller signal does not reach the
DTR-6.2 remote sensor
IR
If the DTR-6.2 is located inside a cabinet or other enclosure where
the infrared rays from the remote controller cannnot enter, then
operation with the remote controller will noe be possible. In such a
case, it will be necessary to install a remote sensor at a location
outside of the cabinet for the infrared rays from the controller to
reach.
With this connection, select “Main” for the Preference → IR IN
Setup → Position setting in the Setup menu (see page 42).
IR Receiver
Connecting
block
IR IN
IN
OUT
DTR-6.2
If the remote controller signal does not reach
other components
In this situation, you will need to use a commercially available IR
emitter. Connect the mini plug of the IR emitter to the IR OUT
terminal on the DTR-6.2 and then place the IR emitter on the remote
sensor of the component or facing it. When the IR emitter is
connected, only the signal input to the IR IN terminal is output to the
IR OUT terminal. The signal input from the remote sensor on the
front of the DTR-6.2 will not be output to the IR OUT terminal.
DTR-6.2
Remote Controller
IR Receiver
Connecting
block
IR IN
In the
cobinet
DTR-6.2
: Signal flow
IR OUT
IR Emitter
The IR IN input allows you to control the DTR-6.2 from the remote
zone (Zone 2) with the remote controller even though the remote
zone is physically separated. The diagram below shows how to make
the proper connections for the remote zone.
With this connection, select “Zone 2” for the Preference → IR IN
Setup → Position setting in the Setup menu (see page 42).
Remote Controller
other
component
: Signal flow
To IR IN
other component
IR Receiver
: Signal flow
DTR-6.2
Remote control
sensor
Connecting
block
IR
Emitter
IN
OUT
Remote controller
Main room
: Signal flow
20
Remote room
DTR-6.2
Mini plug
IR Emitter
Mini plug cable
Connecting the power
SEND/LEARN
indicator
ON
Standby indicator
STDBY
Standby/On
RCVR MODE
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
MUTING
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Power
Audio
Selector
FM Mode
Preset Memory
Video 1
Dimmer
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
To wall outlet
HOME THEATER CONTROLLER
RC-441M
• The DTR-6.2 is shipped with the main power (Power) switch in
the on position ( ON). When the power cord is plugged in for
the first time, the DTR-6.2 will automatically enter the standby
state and the Standby indicator will light (same condition after
step 2 below).
• Before you plug in the DTR-6.2, confirm that all connections
have been made properly.
• Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall outlet
on a different circuit.
To change the display of the input source from TAPE to
MD:
If you connected an MD recorder to the TAPE jack on the DTR-6.2,
you can have “MD” appear when the TAPE source button is pressed.
By changing the display, if an Integra/Onkyo MD recorder zconnected, the z system functions will become enabled.
Changing the display:
Press and hold down the TAPE source button until the display
changes from TAPE to MD (approx. 3 seconds).
TAPE
1. Plug the power cord into an AC wall outlet.
2. Press the Power switch to set the
DTR-6.2 to standby state.
The STANDBY indicator will light up.
3. Press the Standby/On button to turn
on the DTR-6.2. The display and four
jog dial indicators will light up and
the Standby indicator will turn off.
If you press the Standby/On button again,
the receiver returns to Standby mode.
To return the display to its original setting, perform the same
procedure. This setting is necessary to allow z system functions
for the connected cassette tape or MD recorder.
Turn off
Turning the power on from the remote controller:
Before you can use the remote controller, you must perform steps 1
and 2 above and place the DTR-6.2 in the standby state.
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
Memory preservation
This unit does not require memory preservation batteries. A builtin memory power backup system preserves the contents of the
memory during power failures and even when the POWER
switch is set to off. The POWER switch must be set to on in order
to charge the backup system.
The memory preservation period after the unit has been turned off
varies depending on climate and placement of the unit. On the
average, memory contents are protected over a period of a few
weeks after the last time the unit has been turned off. This period
is shorter when the unit is exposed to a highly humid climate.
2. Press the ON button to turn on the
DTR-6.2 (take it out of the standby
state).
To return the DTR-6.2 to the standby state,
press the STDBY button.
21
Connecting antennas
To use the tuner of DTR-6.2, it is necessary to prepare the supplied
FM and AM antennas.
• Adjustment and placement of the FM and AM antennas for
better reception must be done while listening to a station
broadcast.
• If better reception cannot be obtained, then placement of an
outside antenna is recommended.
Assembling the AM loop antenna
Assemble the loop antenna as shown in the illustration.
• Refer to “Connecting the AM loop antenna” below for details on
connecting the loop antenna.
Connecting the included antennas
Connecting the FM indoor antenna:
The FM indoor antenna is for indoor use only. During use, extend the
antenna and move it in various directions until the clearest signal is
received. Fix it with push pins or similar implements in the position
that will cause the least amount of distortion.
If the reception is not very clear with the attached FM indoor
antenna, the use of an outdoor antenna is recommended.
Connecting the AM loop antenna:
The AM loop antenna is for indoor use only. Set it in the direction
and position where you receive the clearest sound. Put it as far away
as possible from the DTR-6.2, televisions, speaker cables, and power
cords.
When reception is not satisfactory with the attached AM loop
antenna alone, connection of an outdoor antenna is recommended.
(Indoor) AM loop antenna
FM antenna
Insert into the hole.
ANTENNA
AM
Connecting the AM antenna cable
1. Press down the lever.
FM
75
2. Insert the wire into the hole.
3. Release the lever.
1
2
3
Strip away the insulation from the end of
the cable, then fully insert the stripped
end of the cable.
Hint:
Either of the split ends of the AM antenna can be connected to either
terminal. Unlike speaker cabling, there is no polarity for AM
broadcast signals.
22
Connecting antennas
Connecting an FM outdoor antenna
Please make sure that you follow the considerations:
• Keep the antenna away from noise sources (neon signs, busy
roads, etc.).
• It is dangerous to put the antenna close to power lines. Keep it
well away from power lines, transformers, etc.
• To avoid the risk of lightning and electrical shock, grounding is
necessary. Follow item 14 of the “Important Safeguards” on
page 2 when you install the outdoor antenna.
Directional linkage
Do not use the same antenna for both FM and TV (or VCR)
reception since the FM and TV (or VCR) signals can interfere with
each other. If you must use a common FM/TV (or VCR) antenna, use
a directional linkage type splitter.
To receiver
To TV (or VCR)
ANTENNA
AM
FM
75
Connecting an AM outdoor antenna
An outdoor antenna will be more effective if it is stretched
horizontally above a window or outside.
• Do not remove the AM loop antenna.
• To avoid the risk of lightning and electrical shock, grounding is
necessary. Follow item 14 of the “Important Safeguards” on
page 2 when you install the outdoor antenna.
Outdoor antenna
ANTENNA
(Indoor)
AM loop antenna
AM
FM
75
23
Speaker setup
After you have installed the DTR-6.2, connected all the components,
and determined the speaker layout, it is now time to perform the
settings in the Speaker Setup menu for the optimum sound acoustics
for your environment and speaker layout.
Before you perform the following settings, it is important that you
first determine the following characteristics:
• The types and sizes of the speakers that are connected.
• The distance from each speaker to your normal listening
position.
Jog dial
Setup
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Before performing the settings, write down your speaker
settings in the diagram below for future reference.
Treble
CD
Return
Your speaker settings:
Monitor
SW
Front
b
Center
c
Front
b
a. meters / feet
b. [
]m/ft
c. [
]m/ft
d. [
]m/ft
d
SL
d
The normal order for performing the settings for speaker setup in
your DTR-6.2 is to set the speaker configuration settings first, set the
speaker distances second, and then calibrate the speaker levels third.
Below is an explanation of how to perform these settings using the
controls on the DTR-6.2.
You can also perform these settings using the On-Screen Display
(OSD) menu (see page 34).
The settings are in a hierarchical configuration as shown below.
Level 1 Main menu level
The level consisting of the menus contained in the Setup menu.
Level 2 Menu level
The level consisting of the submenus contained in each menu.
Level 3 Submenu level
The level consisting of the parameters contained in each submenu.
SR
Speaker Configuration submenu
This submenu provides settings that tell the DTR-6.2 which speakers
you have connected and what size they are.
Use the buttons on the DTR-6.2 to navigate through the menus and
set the various settings and parameters according to your system
setup and layout.
Buttons to be used
Setup
DSP / Mode ADJ
Push To Enter
DSP / Mode ADJ
Push To Enter
1. Press the Setup button.
If a menu other than “1. Speaker Setup”
appears, turn the jog dial until “1. Speaker
Setup” does appear.
Setup button:
Press to enter the main menu level and put the DTR6.2 in the mode for setting the various parameters. If
currently in the setting mode, press to exit.
Jog dial:
If the indicators directly above and below the jog dial
are lit, turning the jog dial selects a submenu and
pushing the jog dial enters the selected submenu (i.e.
takes you one level down).
If the indicators directly to the left and right of the jog
dial are lit, turning the jog dial changes the setting of
the currently selected parameter and pushing the jog
dial displays the next parameter.
Setup
DSP / Mode ADJ
2. Press the jog dial.
Push To Enter
DSP / Mode ADJ
3. Press the jog dial.
Push To Enter
Return
Return button:
Press to go back one level up.
4. Turn the jog dial to set whether or
not a subwoofer is connected.
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not
connected.
24
DSP / Mode ADJ
Push To Enter
Speaker setup
DSP / Mode ADJ
5. Press the jog once and then turn it
to set the size of your front
speakers.
Large: Select if the front speakers are large
sized.
Small: Select if the front speakers are small
sized.
Speaker Distance submenu
Push To Enter
DSP / Mode ADJ
Push To Enter
This submenu provides settings that tell the DTR-6.2 how far away
your speakers are located from the listening position so that it can
provide the optimum sound space. If you are continuing from setting
the speaker configuration and are still in the setting mode, skip
directly to step 2.
Setup
1. Press the Setup button.
If a menu other than “1. Speaker Setup”
appears, turn the jog dial until “1. Speaker
Setup” does appear.
• If “No” is selected for the Subwoofer setting, then this
setting is fixed to “Large”.
6. Press the jog once and then turn it
to set whether or not a center
speaker is connected and, if one is
connected, its size.
None: Select if no center speaker is
connected.
Large: Select if the center speaker is large
sized.
Small: Select if the center speaker is small
sized.
DSP / Mode ADJ
2. Press the jog dial and then turn it to display the
“Speaker Distance.”
DSP / Mode ADJ
DSP / Mode ADJ
Push To Enter
Push To Enter
Push To Enter
DSP / Mode ADJ
DSP / Mode ADJ
Push To Enter
3. Press the jog dial and then turn it to
select the unit of measurement.
Push To Enter
• If “small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
DSP / Mode ADJ
7. Press the jog once and then turn it
to set whether or not surround
speakers are connected and, if they
are connected, their size.
DSP / Mode ADJ
feet: Select if you will enter the distances in
feet.
meters: Select if you will enter the distances
in meters.
Push To Enter
Push To Enter
DSP / Mode ADJ
4. Press the jog dial and then turn it to
set the distance from the front
speakers to the listening position.
Push To Enter
None: Select if no surround left and right
speakers are connected.
Large: Select if the surround left and right
speakers are large sized.
Small: Select if the surround left and right
speakers are small sized.
DSP / Mode ADJ
ft
DSP / Mode ADJ
Push To Enter
Push To Enter
• If “small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
Pressing the jog dial again returns you to the subwoofer setting.
8. Press the Return button.
You return to the “Speaker Config?” display.
Return
Notes:
• If you press the Return button again, you go back up one more
level.
• To exit the setting mode immediately, press the Setup button.
5. Repeat the procedure in step 4 to set the distance
from the center speaker and the surround speakers
to the listening position.
6. Press the Return button.
You return to the “Sp Distance?” display.
Return
Notes:
• If you press the Return button again, you go back up one more
level.
• To exit the setting mode immediately, press the Setup button.
25
Speaker setup
Level Calibration submenu
About the other settings
This submenu allows you to set the volume levels of each speaker
individually so that they all sound at the same level when heard from
the listening position. If you are continuing from setting the speaker
distances and are still in the setting mode, skip directly to step 2.
Note:
This setting cannot be made when Zone 2 is turned on, so be sure to
put Zone 2 in the standby mode.
Setup
1. Press the Setup button.
If a menu other than “1. Speaker Setup”
appears, turn the jog dial until “1. Speaker
Setup” does appear.
The factory settings for your DTR-6.2 are given in the table on page
12. If you connect your system in accordance with these factory
settings, there is no need to change them. However, if you do not,
you will need to change the settings that do not match. If you do not,
signals may not be properly received resulting in poor sound or
image quality, no digital output, or no output at all.
Changing a digital input setting:
1. Press the input selector button for the source that
you want to change.
2. Press the Setup button.
3. Turn the jog dial to display “2. Input Setup.”
2. Press the jog dial and then turn it to display the
“Level Cal?”
DSP / Mode ADJ
DSP / Mode ADJ
Push To Enter
Push To Enter
4. Press the jog dial.
“Audio Setup?” appears.
5. Press the jog dial again.
“D.Input: xxx” appears.
6. Turn the jog dial and select the connector to which
the digital source is connected.
7. Press Return repeatedly or press Setup to exit the
setting mode.
3. Press the jog dial.
A test sound (pink noise) will be heard from
the left front speaker. At this point, it is not
necessary to adjust the volume of the test
sound.
DSP / Mode ADJ
1. Press the input selector button for the source that
you want to change.
Push To Enter
2. Press the Setup button.
3. Turn the jog dial to display “2. Input Setup.”
db
DSP / Mode ADJ
4. Press the jog dial again.
The test sound will now be heard from a
different speaker.
Changing the multichannel setting:
Push To Enter
4. Press the jog dial.
“Audio Setup?” appears.
5. Press the jog dial twice.
“Multich: xxx” appears.
6. Turn the jog dial to select “Yes” or “No.”
5. Turn the jog dial to adjust the
volume of the test sound from this
speaker to the same level that you
heard from the previous speaker.
DSP / Mode ADJ
7. Press Return repeatedly or press Setup to exit the
setting mode.
Push To Enter
Changing the Component Video Input setting:
6. Repeat the procedure in step 4 and 5 until the volume
of the test sound from all speakers is the same level.
Each time you press the jog dial, the test sound will be heard
from a different speaker. The speaker order for calibration is
front left → center → front right → surround right → surround
left → subwoofer.
7. Press the Return button.
You return to the “Level Cal?” display.
Notes:
• If you press the Return button again, you go back up one more
level.
• To exit the setting mode immediately, press the Setup button.
1. Press the input selector button for the source that
you want to change.
2. Press the Setup button.
3. Turn the jog dial to display “2. Input Setup.”
4. Press the jog dial.
“Audio Setup?” appears.
5. Turn the jog dial to display “Video Setup?”
6. Press the jog dial.
“Cmponent: xxx” appears.
7. Turn the jog dial to select the connectors to which
the source is connected (“Input 1” or “Input 2”).
8. Press Return repeatedly or press Setup to exit the
setting mode.
26
Listening to Radio Broadcasts
FM Mode
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
FM AM
Tuning
One of the features of the DTR-6.2 that is most frequently used is its
ability to play FM and AM broadcast radio stations. The DTR-6.2
provides a number of listening modes perfect for listening to the
radio and getting the most out of your audio system. Also, by
presetting radio stations that you listen to frequently, you can select
them easily by pressing the CH
button on the remote controller.
Tuning into a radio station
1. Press either the AM or FM input
source button.
Listening to a stereo radio station (FM mode)
When you tune into a radio station, TUNED
indicator appears in the display. If you tune into
an FM station in stereo, then “FM STEREO”
appears. If the signal is weak, it may be
impossible to tune into the station in stereo. In
such a case, press the FM Mode button on the
front panel. The AUTO indication disappears
and the radio station is output in the monaural
mode. To return to stereo, press the FM Mode
button again. “AUTO” appears. Some interstation noise may be heard, but the sound will
not cut in and out as it would if stereo was
selected.
FM Mode
2. Using the Tuning and buttons
on the front panel, tune into the
station you desire.
“FM STEREO”
(Lights red)
Tuned
in stereo
Auto mode
TUNED
FM STEREO
Band
AUTO
Frequency
• The tuner frequency changes in 50 kHz increments for FM
and 10 kHz increments for AM.
• When tuning into FM stations, you can press the Tuning or
button continuously for more than 0.5 seconds to scan for
an FM station in the direction of the button you pressed (FM
auto tuning mode). After you release the button and a station
is received in stereo, the scanning stops.
27
Listening to Radio Broadcasts
Jog dial
Preset Memory
Preset
RCVR
MODE
CH
Standby/On
Rec Out
Zone 2
Zone 2 Level
CH Level
Master Volume
MUTING
Setup
DSP/ Mode ADJ
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
TUN
FM AM
HOME THEATER CONTROLLER
RC-441M
Presetting a radio station
Selecting a preset radio station
1. Tune into the radio station you desire (see “Tuning
into a radio station” ).
2. Press the Preset Memory button on
the front panel.
“Preset In?” appears in the front display for
about five seconds.
Preset Memory
1. Press either the AM or FM input
source button. The front display
should show the currently selected
frequency.
If it displays the listening mode, press the
Display button to display the frequency.
2. Press the Preset / button and
select the number of the desired
preset station.
Preset
When using the remote controller:
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
DSP / Mode ADJ
3. Press the jog dial.
The MEMORY indicator lights red.
2. Press the TUN button.
Push To Enter
“MEMORY”
(Lights red)
3. Press the CH
button and select the number of the
desired preset station.
MEMORY
Erasing a preset radio station
4. Turning the jog dial, select a preset
number (from 1 to 40) to assign the
station to be preset.
“MEMORY”
(Lights red)
DSP / Mode ADJ
ch
Push To Enter
Flash
AUTO
ch
5. Press the jog dial to finalize the
procedure.
This programs the radio station as a preset
radio station.
• Up to 40 stations can be stored in memory
as preset radio stations.
Preset Memory
2. Press the Preset Memory button.
“Preset In?” appears.
TUNED
MEMORY
1. Press the AM or FM button and press the Preset /
button to select the preset radio station that you want
erase (see above).
DSP / Mode ADJ
DSP / Mode ADJ
3. Turn the jog dial to display “Preset
Erase?”
Push To Enter
ch
Push To Enter
DSP / Mode ADJ
4. Press the jog dial.
The selected preset station is erased.
Push To Enter
28
Enjoying music or videos with the DTR-6.2
Master Volume
VOL
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
MUTING
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Phones
FM Mode
Preset Memory
Video 1
Dimmer
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Bass
Input source buttons
Treble
CD
INPUT
SELECTOR
buttons
Treble
HOME THEATER CONTROLLER
RC-441M
Though the DTR-6.2 is often used to listen to the radio, it does not
show you its true ability until it is used to play music or watch
videos, DVDs, and the like. The DTR-6.2 has the latest in state-ofthe-art features to play back today’s acoustic technologies with the
utmost in fidelity and power. From a two-speaker system to a fivespeaker system, you are assured a sound space that you can always
enjoy.
Temporarily turning off the sound
To turn off the sound momentarily, such as when interrupted by a
phone call, press the MUTING button on the remote controller.
When pressed, “Muting” is displayed on the DTR-6.2. Press the
MUTING button again to turn the sound back on.
Remote controller
Basic operation
1. Press the input source (or input selector on the
remote controller) button.
Adjusting the bass and treble
DTR-6.2
DVD
Video 1
Video 2
VCR 1
VCR 2
Video 3
Video 4
Tape
FM
AM
Phono
CD
You can adjust the bass and treble levels using the Bass and Treble
dials. This function only affects the front left and right speakers. For
multichannel sources, these dials will not work if the tone control is
set to “Off.”
Bass
Treble
Remote controller
2. Turn on the corresponding component and play the
media.
3.
Adjust the volume.
DTR-6.2
Remote controller
Master Volume
Adjusting the main volume adjusts the volume level output from
all the speakers connected to the DTR-6.2 together. If
headphones are connected, this also adjusts the volume heard
from the headphone speakers. To adjust the volume, either press
the VOL
buttons on the remote controller or turn the Master
Volume dial. To increase the volume, turn the dial clockwise; to
decrease the volume, turn the dial counterclockwise. The
volume can be set to Min, 1 to 79, and Max.
Listening with headphones
To listen with headphones, plug a pair headphones with a standard
stereo plug into the Phones jack on the DTR-6.2 front panel.
When you connect headphones, the unit will enter STEREO mode
automatically and no sound will be heard from the speakers.
If you have selected MULTI CH INPUT, you will hear sound only
from the FRONT L and R channels.
The headphone volume level can be adjusted at the Setup menu (see
page 42).
Note that the signal to the remote zone (Zone 2) will not be affected
whether or not headphones are connected.
Phones
29
Enjoying music or videos with the DTR-6.2
Jog dial
Display
SLEEP
Dimmer
CH Level
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
CH SEL
Setup
MUTING
Standby
Return
Power
Push To Enter
On
Of f
Display
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
LEVEL
Phones
Audio
Selector
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
DISPLAY
HOME THEATER CONTROLLER
RC-441M
Using the sleep time (remote controller only)
Switching the display
While listening to or watching an input source, you can display the
information regarding the type of source and signal being input by
pressing the
button on the DTR-6.2 or the DISPLAY button on the remote
controller.
DTR-6.2
DIMMER
Remote controller
Display
When an input source other than FM or AM is selected:
The SLEEP button enables you to set the DTR-6.2 to turn off
automatically after a specified time period. If you press it once, the
DTR-6.2 will turn off after 90 minutes. Each time it is pressed
thereafter, the remaining time until the DTR-6.2 turns off decreases
by 10 minutes. While, the sleep function is enabled, you can press
the SLEEP button to see how much time is left. To cancel the sleep
function, press the SLEEP button when the time displayed is less
than 10 minutes.
If you are using the remote zone (Zone 2), it will turn off at the same
time as the main zone. If you want to set the sleep function for Zone
2 only, set the sleep function with main zone turned on and then put
the main zone into the standby state.
Remote controller
Input + volume
Program format*
Temporarily changing the speaker output levels
To change the individual speaker volumes temporarily, follow the
procedure given below. Each channel can be set between –12 to +12
decibels. Note that the calibration settings will return to the original
settings when the DTR-6.2 is put in standby.
Input +
Listening mode
or Multi Ch
* If the input signal does not have a program format, then this will
be skipped.
CH Level
1. Press the CH Level button and select
the desired speaker.
DSP / Mode ADJ
2. Turn the jog dial to adjust the
volume level.
When FM or AM is selected as the input source:
FM/AM frequency +
Preset no.
Push To Enter
ch
When using the remote controller:
1. Press the RCVR MODE button.
FM/AM +
Listening mode
2. Press the CH SEL button and select
the desired speaker.
Adjusting the brightness of the front display
You can adjust the brightness of the front display of the DTR-6.2
with DIMMER button on the remote controller or Dimmer button
on the DTR-6.2 front panel.
DTR-6.2
Dimmer
30
Remote controller
3. Press the LEVEL or button to
adjust the volume level.
Notes:
• You cannot select a speaker if the Speaker Config sub-menu of
the Speaker Setup is set to No or None.
• If the speaker level is set to +1 dB or higher, the maximum level
indicated on the display will change if you raise the volume
level.
• When you press the TEST button after you set the level, the
current level will be used as the value set via the test tone.
Enjoying music or videos with the DTR-6.2
Jog dial
Master Volume
VOL
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
AUDIO
Setup
MUTING
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
FM Mode
Preset Memory
Video 1
Dimmer
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
DIRECT
Bass
Audio Selector
Treble
HOME THEATER CONTROLLER
RC-441M
Changing the audio mode
3. Turn on the connected component and start playing
the desired media.
Press the Audio Selector button on the front panel (or AUDIO button
on the remote controller) to change the audio mode. Each time the
button is pressed, the mode changes from “AUTO” → “Multich” →
“Analog” and back to “AUTO.” The “AUTO” audio mode is
recommended for normal circumstances.
DTR-6.2
Remote controller
Audio
Selector
AUTO (automatic detection): With this setting, the DTR-6.2
automatically detects whether the input signal is digital or analog.
When a digital signal is not input, then the analog signal is played.
4. If necessary, adjust the output level of each speaker
as desired (see page 30).
Adjust the speaker output levels so that you can hear the same
sound level from each speaker at the listening position. For the
front right, front left, center, surround right, and surround left
speakers, the output levels can be adjusted between –12 to +12
decibels. The subwoofer can be adjusted between –30 to +12
decibels.
5. Adjust the volume with the Master Volume dial or the
buttons on the remote controller.
VOL
DTR-6.2
Remote controller
Master Volume
Multichannel: Select this setting to play back the input from the
component connected to the MULTI CHANNEL INPUT port. This
setting is effective when the Multichannel setting in the Audio Setup
sub-menu is set to “Yes” (see pages 26, 38).
Analog: Select this setting to play back the input from a source
component connected to an analog audio input jacks. With this
setting, even if a digital signal is input from the same component,
only the analog signal will be output.
Enjoying the multichannel output
Before starting operations, first make sure that the multichannel
connection is properly made and that the Multichannel setting of the
Input Setup → Audio Setup submenu is set to “Yes.”
Using the tone control:
To make the BASS and TREBLE dials work for multichannel
sources, you must first set the tone control to “On.”
1. Turn the tone control on by pressing either the jog
dial on the DTR-6.2 or the DIRECT button on the
remote controller.
DTR-6.2
Remote controller
DSP / Mode ADJ
Push To Enter
1. Press the input source button for the component with
multichannel output connected to the MULTI
CHANNEL INPUT on the rear of the DTR-6.2.
When pressed only once, the current setting appears, so press
twice to change the setting.
2. Adjust the tone using the Bass and Treble dials.
2. Select “Multich” using the Audio Selector button on
the front panel (AUDIO button on the remote
controller).
DTR-6.2
Audio
Selector
Bass
Treble
Remote controller
Notes:
• Adjusting the volume level of each speaker for the MULTI CH
INPUT source does not affect the speaker level adjusted by the
listening position.
• If the speaker level is set to +1 dB or higher, the maximum level
indicated on the display will change if you raise the volume
level.
31
Using listening mode
The DTR-6.2’s surround sound enables you to enjoy the presence of
a movie theater or concert hall in your room.
The configuration of the speakers are very important for the
surround sound. Refer to “Connecting speakers” on page 17.
Before using a listening mode, make sure the Speaker Setup
parameters have been set (refer to page 24-26). Once the parameters
have been set, it is not necessary to set them again.
Listening modes
Stereo
This mode has all input sounds output from the left and right front
speakers.
Direct
This mode delivers pure sound with minimum sound quality
adjustment and filtration. The sound recorded for the right and left
front channels is output to the right and left front speakers only and
not output to the subwoofer.
Surround modes
With this mode, decoding is performed automatically to match the
input signal. This original mode adds no sound processing to the
input signal.
• Dolby D (Dolby Digital)
Digital data with AC-3 compression and a maximum of 5.1channel* surround sound. This source signal comes from DVDs
and LDs that have the
mark and therefore recorded for
5.1-channel output. This source also comes from digital satellite
broadcasts that support dolby Digital.
• DTS
DTS (Digital Theater System) is compressed digital data with a
maximum 5.1-channel* surround output that allows for an
extremely high-quality sound. This source signal requires a
DVD player that supports DTS output and comes from compact
discs, DVDs, and LDs that have the
mark.
Notes on DTS:
• If you play a CD or LD that supports DTS when the “Analog”
setting is selected on the DTR-6.2, the DTS encoded signal
will not be decoded and noise will be output. This noise could
damage the amplifier and speakers. Therefore, be sure to
selected “Auto” and use the digital input jacks (OPTICAL or
COAXIAL) to connect the DTS source.
• The DTS indicator on the DTR-6.2 lights while a DTS source
is played. When playback finishes and the DTS signal
transmission stops, the DTR-6.2 remains in DTS mode and
the DTS indicator remains lit. This prevents noise when you
operate the pause or skip button on the player. Therefore, if
the source is immediately switched from DTS to PCM, the
PCM signal may not be played. In this case, stop the playback
of the source on the player for about three seconds and then
resume playback.
• If you press the pause or skip button on the player while
playing a DTS source, on rare occasions a short noise may be
heard. This is not a malfunction.
• You may not be able to play some DTS source signals from
certain CD players and LD players even if you connect the
player to the DTR-6.2 digitally. This is because the digital
signal has been processed (such as the output level, sampling
frequency, or frequency response) and the DTR-6.2 cannot
recognize the signal as DTS data. Therefore you may hear
noise when you play a DTS source while processing the
signal.
32
• The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, TAPE
OUT, output analog audio signals. Do not record from CDs or
LDs that support DTS using these outputs. If you do, the
DTS-encoded signal will be recorded as noise.
* The 5.1-channel digital surround format has a variety of versions
including Dolby Digital and DTS. The 5.1- channel digital
surround format enables you to individually record and play five
full-range (20 Hz to 20 kHz) channels (left and right front,
center, and two surround channels) plus an LFE channel (Low
Frequency Effect) for the low-range effect sound. It will create a
realistic sound that can be heard in the theaters and concert halls.
• DOLBY PRO LOGIC II Surround
This mode is a new generation 5-channel surround system that
provides performance between the 4-channel (left front, right
front, center, and monaural surround) Pro Logic Surround and
the 5.1-channel Dolby Digital Surround. This mode can be set to
the Movie mode designed for playing movies and the Music
mode designed for listening to music. In the Movie mode, the
surround channels, which used to provide monaural output over
only a narrow frequency range, now provide complete stereo
output over the full frequency range. The result is movie viewing
with a realistic feel of movement. The Music mode uses the
surround channels to provide a natural sound space that cannot
be provided with normal stereo output.
This mode can be used with VHS and DVD videos with the
mark and certain television programs. The
Music mode can be used with music compact discs and other
stereo sources.
You can press the SURR button on the remote controller to
switch between MOVIE and MUSIC. The initial setting is
MOVIE. This setting can be made for each input source.
If no surround speakers are connected, then the surround sound
is divided and output from the front left and right channels (3
stereo).
Orchestra
This mode is appropriate for classical and opera music. The center
channel is cut and the surround channels are emphasized to widen
the stereo image. It will simulate the natural reverberation that is
created in large halls.
TV Logic
This mode gives realistic acoustics to TV programs that are aired
from TV studios. It enhances the entire surround sound and clarity of
the conversation.
Unplugged
This mode is suitable for acoustical instrumental sounds, vocals, and
jazz music. By emphasizing the front stereo image, it will simulate
the acoustics that you would experience in front of the stage.
Studio-Mix
This mode is for rock and popular music. The lively sounds are
enhanced for a powerful acoustic image that simulates the feeling of
being in a club or rock concert.
All Ch Stereo
This mode is designed for playing background music. The front,
surround, and surround back channels create a stereo image that
encompasses the entire area.
Using listening mode
Jog dial
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
MUTING
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
Listening
mode
buttons
Re-EQ
HOME THEATER CONTROLLER
RC-441M
Changing the listening mode
To change the listening mode during playback, press the listening
mode buttons on the remote controller.
You can also set the listening mode using the jog dial on the DTR6.2. Push the jog dial repeatedly to cycle the listening mode from
Direct→Stereo→Surround→All Ch Stereo→Direct. Turn the jog
dial to change the listening mode in the same manner as DSP / on
the remote controller.
DTR-6.2
Using Cinema Re-Equalization
Depending on the listening mode, you can either turn Re-EQ on or
off. Re-EQ (re-equalization) takes the edginess or “brightness” out
of your home cinema sound to compensate for the fact that sound
mixed for theaters may sound too bright when played back through
speakers in the home environment.
Remote cotroller only
Remote controller
DSP / Mode ADJ
Push To Enter
DIRECT: Changes the listening mode directly to the Direct
listening mode. If pressed, the listening mode for the selected input
source set in the Listening Mode Preset sub-menu is also changed to
the Direct listening mode.
On: Select to turn on the re-equalization filter.
Off: Select to turn off the re-equalization filter.
Note:
The Re-EQ function is effective on the Dolby Pro Logic II Movie
and Dolby Digital modes.
STEREO: Changes the listening mode directly to the Stereo
listening mode. If pressed, the listening mode for the selected input
source set in the Listening Mode Preset sub-menu is also changed to
the Stereo listening mode.
SURR (Surround): Changes the listening mode to the surround
mode for the current input signal (e.g., Dolby Pro Logic II, Dolby
Digital, or DTS). If pressed, the listening mode for the selected input
source set in the Listening Mode Preset sub-menu is also changed to
the Surround listening mode.
For Dolby Pro Logic II, this button also changes the mode between
Dolby Pro Logic II Movie and Dolby Pro Logic II Music.
A.ST(All Channel Stereo): Changes the listening mode directly to
the Stereo listening mode. If pressed, the listening mode for the
selected input source set in the Listening Mode Preset sub-menu is
also changed to the All Channel Stereo listening mode.
DSP / : Changes the listening mode as shown below.
Direct ↔ Stereo ↔ Surround ↔ Orchestra ↔ Unplugged ↔
Studio-Mix ↔ TV Logic ↔ All Ch Stereo ↔ Direct.
If pressed, the listening mode for the selected input source set in the
Listening Mode Preset sub-menu is also changed.
Note:
If you want to switch between Dolby Pro Logic II Movie and Dolby
Pro Logic II Music at the DTR-6.2, press the jog dial and select
“Surround” for the listening mode.
33
Setup menus
When making the various settings required to configure your DTR6.2 optimally, you can either use the OSD menu that appears on your
television monitor or you can use the display on the front of the
DTR-6.2.
The OSD menu is a settings menu that is displayed on your TV
monitor.
For use as reference when performing the setting procedures, this
manual shows both the OSD menu displayed on your television
monitor and the display on the front of the DTR-6.2.
The Setup menu consists of a main screen that is divided up into 5
menus: Speaker Setup, Input Setup, Listening Mode Setup,
Preference, and OSD Setup. These menus are then divided up into
various sub-menus, and these contain settings for you to optimize
your home theater as you wish.
1.Speaker Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration
|ENTER|Quit:|SETUP|
2.Input Setup
Input:DVD
1.Audio Setup
2.Video Setup
3.Listening Mode Preset
4.IntelliVolume
5.12V trigger
|ENTER|Quit:|SETUP|
3.Listening Mode Setup
1.Stereo Setup
2.Surround Setup
3.Orchestra Setup
4.Unplugged Setup
5.Studio-Mix Setup
6.TV Logic Setup
7.All Ch Stereo Setup
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.OSD Setup
|ENTER|Quit:|SETUP|
4.Preference
|ENTER|Quit:|SETUP|
1.Volume Setup
2.Headphones Level
3.Late Night Setup
4.IR IN Setup
5.Powered Zone2 Setup
|ENTER|Quit:|SETUP|
5.OSD Setup
1.OSD Setup
2.OSD Position
Main menu
|ENTER|Quit:|SETUP|
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.OSD Setup
Menu
1.Speaker Setup
Sub menu
1.Speaker Config
2.Speaker Distance
3.Level Calibration
1-1.Speaker Config
a.Subwoofer
b.Front
c.Center
d.Surround
|ENTER|Quit:|SETUP|
:Yes
:Large
:Large
:Large
|ENTER|Quit:|SETUP|
Quit:|SETUP|
34
Setup menus
Navigating through the Setup menu
The explanations here assume you are using the buttons on the
remote controller when entering the Setup menu. However, you can
use the buttons on the DTR-6.2 as well. When using the buttons on
the DTR-6.2, refer to the table on the right and pages 24 to 26.
In addition to the display of the Setup menu on your television
monitor, the corresponding menu will also be displayed in the front
display on the DTR-6.2.
The buttons on the remote controller correspond to those on the
DTR-6.2 as shown on the right.
Setting procedures and button operations
Remote controller
Main menu
Display menu
(display OSD menu)
Select item
DTR-6.2
Setup
DSP / Mode ADJ
Push To Enter
1. Press the SETUP button.
The main menu screen of the Setup menu
appears on your television monitor and the
DTR-6.2 enters the setup mode.
2. Using the and cursor buttons,
select the menu that you want to
enter.
Enter selected item
DSP / Mode ADJ
Push To Enter
Menu
Select item
DSP / Mode ADJ
Push To Enter
Enter selected item
DSP / Mode ADJ
3. Press the ENTER button to enter the
selected menu.
The screen for that menu appears.
Push To Enter
Submenu
Select item
4. Using the and cursor buttons,
select the sub-menu that you want to
enter, and press the ENTER button.
DSP / Mode ADJ
Push To Enter
Set parameter
DSP / Mode ADJ
Push To Enter
Other
Move up one level
Return
Each sub-menu has different settings that
can be changed as desired, and they are all
explained below. To change a setting, first
select it using the and cursor buttons,
and then change the setting using the and
cursor buttons.
Exit OSD menu
Setup
5. Press the RETURN button to return
to the previous menu screen, and
again to return to the main screen.
Note:
Press the SETUP button to exit the Setup menu
immediately.
35
Setup menus
1. Speaker Setup menu
1-1. Speaker Config sub-menu
The settings here are also explained on pages 24 to 26. Refer to those
pages for reference.
1.Speaker
1.Speaker Setup
Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
1.Speaker Config
1-1.Speaker
Config
5.OSD
Setup Distance
2.Speaker
3.Level Calibration
4.Bass
Peak Level
a.Subwoofer
:Yes
b.Front
:Large
c.Center
:Large
|ENTER|
Quit:|OSD|
d.Surround
:Large
Menu
1.Speaker
1.Speaker Setup
Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
1.Speaker Config
5.OSD
Setup Distance
2.Speaker
3.Level Calibration
|ENTER| Quit:|OSD|
D|
|ENTER|Quit:|SETUP|
Quit:|SETUP|
Your speaker settings:
Here you will enter which speakers are connected and the size of
each speaker.
Monitor
SW
Front
b
Center
c
Front
b
a. meters / feet
d
SL
b. [
]m/ft
c. [
]m/ft
d. [
]m/ft
d
a. Subwoofer
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
b. Front
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
• If “No” is selected for the Subwoofer setting, then this setting
is fixed to “Large.”
c. Center
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
• If “Small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
SR
Tip:
When setting the speaker size in the Speaker Config sub-menu, use
the guidelines given below.
Large: The complete frequency range for the channel you are setting
will be output from the speaker.
Small: Frequencies of the channel you are setting lower than 80 Hz
will be output from the subwoofer. If the front speakers are set to
“Large,” then the sound may be output from both the left and right
speakers.
36
Menu
d. Surround
None: Select if no surround left and right speakers are
connected.
Large: Select if the surround left and right speakers are large
sized.
Small: Select if the surround left and right speakers are small
sized.
• If “Small” is selected for the Front setting, then “Large”
cannot be selected for this setting.
Setup menus
1-2. Speaker Distance sub-menu
Menu
1.Speaker
Setup
1.Speaker
Setup
2.Input
Setup
3.Listening Mode Setup
4.Preference
1-2.Speaker
Distance
1.Speaker
5.OSD
Setup Config
2.Speaker
Distance
3.Level Calibration
a.UnitPeak Level:feet
4.Bass
b.Front L/R
:12ft
c.Center
:12ft
|ENTER|
Quit:|OSD|
d.Surround L/R : 7ft
|ENTER| Quit:|OSD|
Quit:|SETUP|
Here you will enter the distance from each speaker to your normal
listening position. This is important for the timing of the acoustics to
create the proper sound space that the DTR-6.2 and today’s sound
systems are able to produce.
Note:
Speakers that you selected “No” or “None” for in the Speaker Config
sub-menu will not appear.
a. Unit
feet: Select if you will enter the distances in feet.
meters: Select if you will enter the distances in meters.
b. Front L/R
Set the distance from the front left and right speakers to your normal
listening position between 1 and 30 feet in 1-feet intervals (0.3 to 9
meters in 0.3-meter intervals).
Position the front left and right speakers so that they are the same
distance from the listener. If they are not, you may lose the center
position for stereo sound.
c. Center
Set the distance from the center speaker to your normal listening
position between 1 and 30 feet in 1-feet intervals (0.3 to 9 meters in
0.3-meter intervals).
d. Surround L/R
Set the distance from the surround left and right speakers to your
normal listening position between 1 and 30 feet in 1-feet intervals
(0.3 to 9 meters in 0.3-meter intervals).
Here you will set the volume for each speaker so that they are all
heard by the listener at the same level. This is especially important
for speaker layouts where the left and right speakers are at
different distances or in asymmetrical positions due to room
designs and configurations. These settings and the distance
settings performed above are vital to create the proper acoustics
required for the optimum sound space and dynamics.
Notes:
• The speaker level settings here are not effective for multichannel input sources. To adjust the speaker levels for multichannel input sources, you will need to use the CH SEL,
LEVEL , and LEVEL buttons on the RC-441M remote
controller. See pages 30, 31.
• This setting cannot be made when Zone 2 is turned on, so be
sure to put Zone 2 in the standby mode.
Calibrating the speaker levels
(1) When this sub-menu is entered, the DTR-6.2 will emit a pink
noise from the front left speaker. At this time, the Master
volume automatically increases to the reference level (0dB).
Remember the level of this noise and then press the cursor
button. (Note that this can be adjusted to any level between –
12 and 12 decibels in 1-decibel intervals.) The DTR-6.2 will
now emit the pink noise from the center speaker.
(2) Using the and cursor buttons, adjust the volume level of
the noise from the center speaker so that it is the same level as
the front left speaker. You can jog back and forth between the
speakers to help you compare the volume levels.
(3) Press the cursor button again. The DTR-6.2 will now emit
the pink noise from the front right speaker.
(4) Repeat steps (2) and (3) above for the front right and other
speakers until all speakers are adjusted to the same volume
level.
Note:
• Speakers that you selected “No” or “None” for in the Speaker
Config sub-menu will not appear.
a. Left
Sound comes from the front left speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel intervals.
b. Center
Sound comes from the center speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel intervals.
c. Right
Sound comes from the front right speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel intervals.
1-3. Level Calibration sub-menu
d. Surr Right
Sound comes from the surround right speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel intervals.
Menu
1.Speaker
1.Speaker Setup
Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
1.Speaker Calibration
Config
1-3.Level
5.OSD
Setup Distance
2.Speaker
3.Level Calibration
4.Bass
a.LeftPeak Level
: 0dB
b.Center
: 0dB
c.Right
: 0dB
|ENTER|
Quit:|OSD|
d.Surr Right
: 0dB
e.Surr Left
: 0dB
|ENTER| Quit:|OSD|
f.Subwoofer
: 0dB
e. Surr Left
Sound comes from the surround left speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel intervals.
f. Subwoofer
Sound comes from the subwoofer. Adjust the sound level
between –12 and 12 decibels in 1-decibel intervals.
Quit:|SETUP|
37
Setup menus
2. Input Setup menu
This menu allows you to setup the various input sources available
with the DTR-6.2. Each input source may have a great number of
settings that are difficult to keep track of, so we recommend making
a chart to record what you have set and for which component to
prevent confusion later.
Menu
1.Speaker
Setup
2.Input Setup
Setup
2.Input
Input:DVD
3.Listening
Mode Setup
4.Preference
1.Audio
Setup
5.OSD
Setup
2.Video
Setup
3.Listening Mode Preset
4.IntelliVolume
5.12V trigger
|ENTER| Quit:|OSD|
Current
Input
Source
|ENTER|Quit:|SETUP|
----: Select if the input source is not from a digital input jack.
Note:
Do not assign a digital input to more than one input source. If you are
making a digital connection that requires you to change the default
settings, be sure to always first cancel the current digital input setting
and then assign the new setting.
b. Multichannel
This sub-menu will not appear if AM or FM is selected at the front
panel for the input source. The initial settings are “Yes” for the DVD
input source and “No” for all other input sources. This setting is
normally set to “No,” and only needs to be changed to “Yes” if a
DVD player, MPEG decoder, or other component that has a multi
channel port is connected to the MULTI CHANNEL INPUT port for
5.1-channel audio. For example, if a DVD player is connected to the
MULTI CHANNEL INPUT port, then select DVD at the front panel
as the input source, bring up this sub-menu, and select “Yes” for the
Multichannel setting. You can only select Multichannel with the
Audio Selector button when “Yes” is selected here.
Note:
When playing a device that is actually connected to the MULTI
CHANNEL INPUT terminal, select Multichannel with the Audio
Selector button.
2-1. Audio Setup sub-menu
Initial settings for each input source
Menu
1.Speaker
Setup
2.Input Setup
Setup
2.Input
Input:DVD
3.Listening Mode Setup
4.Preference
a.Audio
Setup
2-1.Audio
Setup
5.OSD
Setup
b.Video
Setup
Input:DVD
c.Listening
Mode Preset
Audio:Auto(COAX1)
d.Tone Control
e.IntelliVolume
a.Digital Input:COAX1
f.12V
Trigger
|ENTER|
Quit:|OSD|
b.Multichannel
:Yes
|ENTER| Quit:|OSD|
Quit:|SETUP|
Input source
DVD
Video 1
Video 2
Video 3
Video 4
Tape
FM
AM
Phono
CD
Digital input
COAX 1
COAX 2
---OPT2
-------
Multichannel
Yes
No
No
No
No
No
---OPT 1
No
No
----: Available for digital input but not set in initial settings.
: Not available for digital input.
The settings made in this sub-menu are valid for the input source that
is currently selected with the input source buttons at the front panel
and, therefore, these settings are made separately for each digital
input source. This sub-menu will not appear if the selected input
source button is AM or FM. If this setting is incorrectly made, the
digital audio signals may not be properly output, or not heard at all.
a. Digital Input
This setting tells the DTR-6.2 which input source button on the front
panel is connected with which digital input jack on the rear panel. To
perform this setting, you must first select a digital input source at the
front panel and then set the name of the digital input jack it is
connected to here.
For example, if the input source selected at the front panel is CD and
the compact disc player is connected to DIGITAL INPUT
(OPTICAL) 1, then select “OPT1” here. If the input source selected
is not connected to a digital input, then select “----.”
OPT1: Select if connected to DIGITAL INPUT (OPTICAL) 1.
OPT2: Select if connected to DIGITAL INPUT (OPTICAL) 2.
COAX1: Select if connected to DIGITAL INPUT (COAXIAL) 1.
COAX2: Select if connected to DIGITAL INPUT (COAXIAL) 2.
38
Setup menus
2-2. Video Setup sub-menu
Menu
Menu
1.Speaker
Setup
2.Input Setup
Setup
2.Input
Input:DVD
3.Listening Mode Setup
4.Preference
2-2.Video
Setup
a.Audio
Setup
5.OSD
Setup
Input:DVD
b.Video
Setup
c.Listening Mode Preset
a.Component
Video
d.Tone
Control
:Input1
e.IntelliVolume
f.12V
Trigger
|ENTER|
Quit:|OSD|
|ENTER| Quit:|OSD|
Quit:|SETUP|
a. Component Video
If a component is connected to the one of the COMPONENT
VIDEO inputs (1 or 2), then that input must be set here. This setting
will not appear if AM, FM, Phono, CD or Tape is selected as the
input source.
The default settings are given below.
Input source selected
DVD
Video 1
Video 2
Video 3
Video 4
2-3. Listening Mode Preset sub-menu
Component video input
INPUT 1
INPUT 2
INPUT 1
INPUT 1
INPUT 1
1.Speaker
Setup
2.Input Setup
Setup
2.Input
Input:DVD
3.Listening Mode Setup
4.Preference
2-3.ListeningMode
Preset
a.Audio
Setup
5.OSD
Setup
Input:DVD
b.Video
Setup
c.Listening Mode Preset
a.Analog/PCM
d.Tone
ControlSource
:Stereo
e.IntelliVolume
f.12V
Trigger
|ENTER|
Quit:|OSD|
b.Digital Format
:Surround
|ENTER| QuSD|
Quit:|SETUP|
With the DTR-6.2, you can set a different listening mode for each
different signal type that comes from each input source and also set
the parameters for the listening mode itself. For example, if your
DVD player also plays compact discs and the DVD video signal is
DTS and the compact disc signal is PCM, then you can set a
different listening mode for each.
This is especially convenient if you frequently play the same types
of movies or music.
See the next page for information regarding the relationship
between input sources and listening modes.
Input source signals
a. Analog/PCM Source
Set a listening mode for the input signal from analog sources and
PCM sources.
Note:
For PCM sources recorded at a sampling rate of 96 kHz or greater,
only the Stereo or Direct listening modes can be selected.
However, the set listening mode is stored in memory.
b. Digital Format
Set a listening mode for the input signal from Dolby Digital and
DTS sources.
• The DTR-6.2 will automatically switch to the listening mode
set for the current input signal. For example, even when using
the same DVD player, if a CD is played, the listening mode
automatically becomes “Stereo,” and if a DVD is played
(Dolby Digital 3/2.1), the listening mode automatically
becomes Dolby D.
39
Setup menus
2-4. IntelliVolume sub-menu
2-5. 12V trigger sub-menu
Menu
Menu
1.Speaker
Setup
2.Input Setup
Setup
2.Input
Input:DVD
3.Listening Mode Setup
4.Preference
2-5.12V
Trigger
a.Audio
Setup
5.OSD
Setup
Input:DVD
b.Video
Setup
c.Listening Mode Preset
a.12V Trigger
d.Tone
Control A :On
e.IntelliVolume
b.12V
Trigger
B :Off
f.12V
Trigger
|ENTER|
Quit:|OSD|
1.Speaker
Setup
2.Input Setup
Setup
2.Input
Input:DVD
3.Listening Mode Setup
4.Preference
a.Audio
Setup
2-4.IntelliVolume
5.OSD
Setup
b.Video
Setup
Input:DVD
c.Listening Mode Preset
d.Tone
Control
a.IntelliVolume
e.IntelliVolume : 0dB
f.12V
Trigger
|ENTER|
Quit:|OSD|
|ENTER| QuSD|
|ENTER| Quit:|OSD|
Quit:|SETUP|
Quit:|SETUP|
a. IntelliVolume
When switching input sources, you may find that the output level for
different components or input sources connected to the DTR-6.2 is
different even though the main volume setting is the same. Under
normal circumstances, you would then have to change the volume
setting each time you change the input source. This IntelliVolume
sub-menu allows you to preset a volume level for each input source
separately so that when you do switch from one input source to
another, the DTR-6.2 adjusts the volume accordingly so that the
resulting volume stays the same. To set the IntelliVolume, simply
select an input source at the front panel, and if that source is quieter
than other sources, increase its decibel level with the
cursor
button, or if it is louder than other sources, decrease its decibel level
with the cursor button.
The IntelliVolume can be adjusted between –12 and +12 decibels.
This sub-menu allows you to make the required settings to turn on
the output from the 12V TRIGGER terminal to control another
component or device with the DTR-6.2 for each input source.
a. 12V Trigger A
On: Select to activate the device connected to the 12V TRIGGER A
terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER A
terminal or you do not want the connected device to activate.
b. 12V Trigger B
On: Select to activate the device connected to the 12V TRIGGER B
terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER B
terminal or you do not want the connected device to activate.
Relationship between input source and listening mode
Input source signal (display)
Type of media
Analog/PCM Source
Digital Format
Tape, CD,
DVD,
Record, Tuner
Digital satellite broadcast,
DVD Video (PCM), LD (PCM)
Digital satellite broadcast
DTS-CD
Dolby Digital 2ch Source
DTS,
All excluding
Listening Mode
●
●
Pro Logic II (Movie)
●
●
Pro Logic II (Music)
●
●
Stereo
Surround
Dolby Digital 2ch
●
Direct
●
Dolby Digital
●
DTS
Orchestra
●
Unplugged
●
Studio-Mix
●
TV Logic
●
All Ch Stereo
●
Notes:
• The listening modes that can be set are different for each input source format.
• You may not be able to select all the listening modes shown here depending on your speaker
configuration or the selected input source.
40
●
Setup menus
3. Listening Mode Setup menu
4. Preference menu
This menu allows you to make adjustments to the various listening
modes. These adjustments are in the form of parameters and each
one is explained below. Note that some parameters cannot be set for
some listening modes and that no sub-menu will have all parameters.
Also, for some input signal formats, changes in the listening mode
parameters may actually result in no change to the resulting output
signal.
Menu
1.Speaker
Setup
4.Preference
2.Input
Setup
3.Listening Mode Setup
4.Preference
1.Volume
5.OSD
SetupSetup
2.Headphones
Level
3.DTS LFE
3.Late
Night
Level
Setup
Setup
4.Powered
44.Powered
4.AM
4.IR
Frequency
IN
setup
Zone2
Zone2
Setup
Setup
Setup
5.Powered Zone2 Setup
|ENTER| Quit:|OSD|
Menu
1.Speaker
Setup
3.Listening
2.Input
SetupMode Setup
3.Listening Mode Setup
4.Preference
1.Stereo
5.OSD
SetupSetup
2.Surround
Setup
3.Orchestra Setup
4.Unplugged Setup
5.Studio-Mix Setup
6.TV|ENTER|
Logic Setup
Quit:|OSD|
7.All Ch Stereo
Setup
|ENTER|Quit:|SETUP|
|ENTER| Quit:|OSD|
4-1. Volume Setup sub-menu
|ENTER|Quit:|SETUP|
Menu
1.Speaker
Setup
4.Preference
2.Input
Setup
3.Listening Mode Setup
4.Preference
4-1.Volume
Setup
1.Volume
5.OSD
SetupSetup
2.Headphones
Level
3.DTS LFE Level Setup
a.MaximumZone2
Volume
4.Powered
Setup
:Off
b.Power
on Quit:|OSD|
Volume
|ENTER|
:Last
Description listening mode parameters
Menu
1.Speaker
Setup
3.Listening
2.Input
SetupMode Setup
3.Listening Mode Setup
4.Preference
3-1.Stereo
Setup
1.Stereo
5.OSD
SetupSetup
2.Theater-Dimensional
Setup
a.Subwoofer
: On
3.Surround
Setup
4.THX Setup
5.Mono
MovieQuit:|OSD|
Setup
|ENTER|
|ENTER| Quit:|OSD|
Quit:|SETUP|
|ENTER| Quit:|OSD|
This sub-menu allows you to make various settings concerning the
volume control of the DTR-6.2.
Quit:|SETUP|
Subwoofer
Set this to “Off” if you are not using a subwoofer (even if one is
connected). If “No” is selected for the Subwoofer setting in the
Speaker Config sub-menu, then this setting will not appear.
Front Effect
You can choose from “Low,” “Middle,” or “High.”
Some live recordings contain acoustic reverberation. When you play
these sources, more reverberation will be applied by the DSP,
creating too much reverb effects and the sound loses frame or
presence. In this case, set this setting to “Low.” No reverberation
from the DSP will be applied to the sound output from the three front
channels, so the sound source is be played as it is without any further
reverberation.
a. Maximum Volume
This setting allows you to set the maximum volume that can be
output with the Master Volume dial to prevent components from
being damaged by excessively loud volumes. The maximum volume
can be set between 30 and 79.
b. Power On Volume
This sets a designated volume setting for the DTR-6.2 to be set every
time that the power is turned on. This prevents the DTR-6.2 from
being turned on while it is set to an extremely high volume and
suddenly output very loud sounds. The power on volume can be set
between min and max. If you do not mind having the DTR-6.2
turned on with its current volume setting, set this to “Last.”
Surround Effect
You can choose from “Low,” “Middle,” or “High.”
This adjusts the reflected and residual noises from the surround left
and right speakers.
Relationship between listening mode and parameter
Listening mode
Parameter
Subwoofer
Front Effect
Surround Effect
Direct
Stereo
Off, On
Surround
Dolby Pro Logic II
Dolby Digital
DTS
Off, On
Orchestra
Unplugged
Studio-Mix
TV Logic
Off, On
Low, Mid, High
Low, Mid, High
All Ch
Stereo
Off, On
The parameters that can be set are different for each listening mode.
41
Setup menus
4-2. Headphones Level sub-menu
4-4. IR IN Setup sub-menu
Menu
Menu
1.Speaker
Setup
4.Preference
2.Input
Setup
3.Listening Mode Setup
4.Preference
4-2.Headphones
Level
1.Volume
5.OSD
SetupSetup
2.Headphones
Level
3.DTS LFE Level Setup
a.Headphones
Level
4.Powered
Zone2
Setup
: 0dB
|ENTER| Quit:|OSD|
1.Speaker
Setup
4.Preference
2.Input
Setup
3.Listening Mode Setup
4.Preference
4-4.IR
INSetup
Setup
1.Volume
5.OSD
Setup
2.Headphones
Level
3.DTS LFE Level Setup
a.Position
:Main
4.Powered
Zone2 Setup
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
Quit:|SETUP|
Quit:|SETUP|
a. Headphones Level
You can use this sub-menu to adjust the volume output from the
headphones so that it matches the level output from the speakers.
The headphone volume can be adjusted between –12 and +12
decibels.
4-3. Late Night Setup sub-menu
Menu
1.Speaker
Setup
4.Preference
2.Input
Setup
3.Listening Mode Setup
4.Preference
4-3.Late
1.Volume
Setup Setup
5.OSD
SetupNight
2.Headphones
Level
3.DTS LFE Level Setup
a.Late Night
4.Powered
Zone2 :Off
Setup
This sub-menu allows you to set where you will be using the remote
controller when you are using it in conjunction with the IR IN
terminal (i.e. remote controller signals are input at the IR IN
terminal).
Main: Select this when using the DTR-6.2 in the main room. If
“Main” is selected at this sub-menu, to perform operations in the
remote zone (Zone 2), you will first have to press the ZONE 2 button
on the remote controller.
Zone 2: Select this when using the DTR-6.2 in the remote zone
(Zone 2). When this is selected, the ON/STDBY, INPUT
SELECTOR, CH
, and LEVEL / (or VOLUME ) buttons
work without having to press the ZONE 2 button on the remote
controller.
4-5. Powered Zone 2 Setup sub-menu
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
Quit:|SETUP|
a. Late Night
Sets “High,” “Low,” or “Off” for the late night function.
Cinema sound has a vast dynamic range; therefore, to hear the
quieter sounds such as human conversations, they must be played
back at larger volumes. When this parameter is set to “High” or
“Low,” the dynamic range of the sound is narrowed down to allow
you to easily hear minute sounds at low volumes. This function is
especially useful if you wish to play a movie at low volumes during
the nighttime.
Notes:
• The depth of the Late Night effect is determined by Dolby
Digital software. Some sounds may produce no or little effect.
• The Late Night function is effective only on Dolby Digital
encoded software.
42
Menu
1.Speaker
Setup
4.Preference
2.Input
Setup
3.Listening Mode Setup
4.Preference
1.Volume
4-5.Powered
Zone2 Setup
5.OSD
SetupSetup
2.Headphones
Level
3.DTS LFE Level Setup
4.Powered
a.PoweredZone2
Zone2Setup
:Activated
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
Quit:|SETUP|
Activated: Select when speakers are connected to the ZONE2
SPEAKERS terminals. During playback in the remote zone (Zone
2), the listening mode for the main zone becomes either Stereo or
Direct.
Not Activated: Select when you are connecting an amplifier to the
ZONE 2 OUT terminals and connecting speakers to that amplifier.
Setup menus
5. OSD Setup menu
This menu provides settings for you to customize the on-screen
display (OSD) for the DTR-6.2 by setting different colors or
positions for its display.
Menu
1.Speaker
Setup
5.OSD Setup
2.Input
Setup
3.Listening Mode Setup
4.Preference
1.OSDSetup
Setup
5.OSD
2.OSD Position
|ENTER| Quit:|OSD|
c. Immediate Display
On: Select this to have the screen immediately display certain
operations as you perform them. The display will remain for a
few seconds after the operation is completed.
Off: Select this to turn off the immediate display of operations.
Hint:
If this is set to “Off,” the background color will not be displayed
even when there is no video signal input.
d. Display Position
Use this setting to select the position of the immediate display that
appears when certain operations are performed. You can position the
immediate display at any of ten different levels ranging from the top
all the way to the bottom.
|ENTER|Quit:|SETUP|
5-2. OSD Position sub-menu
5-1. OSD Setup sub-menu
Menu
1.Speaker
Setup
5.OSD Setup
2.Input
Setup
3.Listening Mode Setup
4.Preference
5-1.OSD
Setup
1.OSDSetup
Config
5.OSD
2.OSD Setup
3.OSD Position
a.Background Color
:Blue1
b.Superimpose
Mode
|ENTER| Quit:|OSD|
:Normal
c.Immediate Display
|ENTER| Quit:|OSD|
:On
d.Display Position
:Bottom
Quit:|SETUP|
This sub-menu allows you to adjust the position of the OSD Setup
menu as it is displayed on your screen. Depending on the monitor
used, there may be cases where the OSD Setup menu is not displayed
in the center and parts of the menus are cut off. To adjust the position
of the OSD Setup menu, simply press the cursor buttons to inch the
menu to position you desire.
Menu
1.Speaker
Setup
5.OSD Setup
2.Input
Setup
3.Listening Mode Setup
4.Preference
5-2.OSD
Position
1.OSDSetup
Config
5.OSD
2.OSD Setup
3.OSD Position
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
Quit:|SETUP|
This sub-menu allows you to customize the OSD Setup menu to
display in the manner you desire.
a. Background Color
Select either Blue1, Blue2, Green1, Green2, Magenta, Red1, or
Red2 as the background color while the OSD Setup menu is
displayed.
b. Superimpose
Off: Select to have the OSD Setup menu displayed on the
selected background color.
Normal: Select to have the OSD Setup menu superimposed over
the current video if one is displayed or on the selected
background color if there is no video signal.
Black: Select to have the OSD Setup menu displayed on a black
background at all times.
VIDEO 1
43
Recording
Caution
• Surround and multichannel audio cannot be recorded.
• You cannot perform digital recording with the DTR-6.2. Also,
digital-to-analog signal conversion is not possible, so to record
audio signals from digital sources (e.g. CD players), their analog
connection must be made as well.
Rec Out
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
Setup
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
AM
Phono
Treble
CD
Input source buttons
Recording the input source (REC OUT selector)
When using the DTR-6.2 to record a source, you must select that
source to be output from the TAPE OUT jacks.
In this example you would press the CD source button. The
signal from the CD player is now output to the TAPE OUT jacks.
DVD
Recording the same source that you are listening to:
Video 1
Video 2
VCR 1
VCR 2
Video 3
Video 4
Tape
FM
AM
Phono
CD
1. Press the input source button for the source that you
want to record.
DVD
Video 1
Video 2
VCR 1
VCR 2
Video 3
Video 4
Tape
FM
AM
Phono
CD
Rec Out
2. Press the Rec Out button repeatedly
until “Rec Sel : SOURCE” appears in
the front display.
The signal from the currently selected source is also output to the
TAPE OUT jacks.
3. Start recording at the recording device connected to
the TAPE OUT jacks.
You can press the Rec Out button to display which input source
is selected for recording. When “Rec Sel : Off” is displayed, no
signal is output for recording.
Notes:
• You cannot use the Rec Out selector to record video signals.
• Be aware that the Zone 2 and Rec Out selectors use the same
circuit and therefore cannot be used at the same time.
• Even if you change the input source that you are listening to, the
input source that is selected for recording will not change.
However, if you have selected FM (or AM) as the source to be
recorded and the AM (or FM) source button is pressed, the
source being recorded will be changed to the AM (or FM) input
signal.
3. Start recording at the recording device connected to
the TAPE OUT jacks.
Note:
Be aware that if you change the input source that you are watching
(or listening to), the source being recording will also change.
Recording a source different from that you are listening
to:
The DTR-6.2 allows you to listen to one source while recording the
signal from another source. The procedure below uses the example
of recording the audio from a CD player while watching the input
from a DVD player.
1. While playing the DVD, press the
Rec Out button.
Rec Out
2. Within 3 seconds, press the input source button of
the source that you wish to record.
44
Recording both the audio and video
The DTR-6.2 also allows you to record the audio and video signals
output from the VIDEO OUT 1 and 2 jacks.
1. Press the input source button for the source you
want to record.
DVD
Video 1
Video 2
VCR 1
VCR 2
Video 3
Video 4
Tape
FM
AM
Phono
CD
2. Start recording at the recording device connected to
the VIDEO OUT 1 and 2 jacks.
Note:
Be aware that if you change the input source that you are watching
(or listening to), the source being recording will also change.
Hint
You can also record the video from one source and the audio from
another source together to make your own home movies and the like.
For example, if you want to record the video from a video camera
connected to VIDEO 4 and the audio from a CD player connected to
CD IN, at step 1 above, press the Video 4 source button and then the
CD source button.
Enjoying music in the remote zone
ON
Zone 2 indicator Zone 2
Zone 2 Level
CH
Standby/On
Rec Out
Zone 2
Zone 2 Level
DSP/ Mode ADJ
CH Level
Master Volume
MUTING
Setup
LEVEL
Standby
Return
Power
Push To Enter
On
Of f
Display
Phones
Audio
Selector
Dimmer
FM Mode
Preset Memory
Video 1
Video 2
Video 3
VCR 1
VCR 2
Tuning
Smart Scan Navigator
Preset
Bass
DVD
Video 4
Tape
FM
Input source buttons
AM
Phono
Treble
INPUT
SELECTOR
buttons
CD
Jog dial
ZONE 2
HOME THEATER CONTROLLER
RC-441M
Here is an explanation of how to setup speakers in a room separated
from the DTR-6.2 so that you can listen to audio sources remotely.
Selecting an input source and adjusting the
volume on the DTR-6.2
1. Press the Zone 2 button on the DTR6.2.
To select the same source for the remote
zone that is selected for the main zone,
press the Zone 2 button again until
“Zone2Sel:SOURCE” appears in the
display.
CD
Zone 2
When “Zone2Sel:Off” is displayed, the output to the remote
zone is turned off.
Caution:
If you are not using the system in the remote zone, always
press the Zone 2 button consecutively to turn the ZONE 2
function off.
Zone 2 Level
3. Press the Zone 2 Level button.
“Zone2 Level” appears for approximately
three seconds.
4. While “Zone 2 Level” is displayed,
turn the jog dial to adjust the volume
to the desired level.
Turning on the Zone 2 and putting it in the standby state
when the DTR-6.2 is in the standby state:
After pressing the ZONE 2 button, press the ON/STDBY button
within 5 seconds.
Zone 2
2. Select a source.
After pressing the Zone 2 button, you must press an input source
button within 3 seconds. The Zone 2 indicator lights.
Ex.: When the CD button is pressed.
Selecting an input source and adjusting the
volume using the remote controller
DSP / Mode ADJ
Push To Enter
Tip:
When using Zone 2, even if you put the DTR-6.2 in the standby state,
it will not affect Zone 2 and the volume in Zone 2 can still be
adjusted. Moreover, components that have their power supply
connect to the AC OUTLET connector on the DTR-6.2 will not be
turned off.
Selecting an input source:
After pressing the ZONE 2 button, press an input source button
within 5 seconds.
If tuner is selected with the TUN button, the CH +/- button becomes
enabled.
Adjusting the volume:
After pressing the ZONE 2 button, adjust the volume using the
LEVEL / buttons within 5 seconds.
Notes:
• If you wish to use the remote controller from a separate room or other
location where the signals will not reach the DTR-6.2, you will need to
purchase a commercially available remote control sensor and emitter
(see page 20).
• After you press the ZONE 2 button on the remote controller, the
Standby indicator on the DTR-6.2 flashes for five seconds. During this
time, you will not be able to perform operations in the main zone using
the remote controller.
• If the source for the main zone is selected as the source for the remote
zone and the source for the main zone is changed, then the source for the
remote zone will change as well.
• In the remote zone, you can only play the source in the 2-channel mode.
You cannot play the source in the remote zone in the surround mode.
• When you are listening to a source in the remote zone (Zone 2), you can
only play sources in the Stereo or Direct modes in the main zone.
Therefore, when sources playing from the multichannel input in the
main zone, audio from the left and right surround speakers will not be
output.
• The Rec Out and Zone 2 buttons use the same circuit and therefore
cannot be used at same times. If the Rec Out button is pressed in the
main room while someone is using the system in the remote zone, the
Zone 2 function will be deactivated and the source will turn off in the
remote zone.
• The Zone 2 terminal is an analog output. Digital signals are not output.
If no sound is heard from the selected input source, check if the
component is connected to the analog inputs.
45
Using remote controller
Overview
The RC-441M remote controller is a useful tool to help you operate
the components of your home theater. To do so, first press the Mode
button that corresponds to the device you wish to control. Then
simply press the desired operation button and the component will
operate accordingly. For example, if you wish to select the CD input
source at the DTR-6.2 with the remote controller, first press the
RCVR MODE button to select the DTR-6.2 and then press the CD
(INPUT SELECTOR) button.
Calling up a preset radio station
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
RCVR MODE
2. Press the TUN input selector button.
3. Press the CH or button to select the desired
preset station number.
CH
TUN
Controlling an Integra/Onkyo cassette tape deck
The z connector of the Integra/Onkyo cassette tape deck must be
connected to the DTR-6.2 (see page 16).
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo cassette
tape deck.
RCVR MODE
VOL
MUTING
TAPE
operation
buttons
HOME THEATER CONTROLLER
RC-441M
Operation buttons:
: Play
: Stop
: Rewind
: Fast forward
: Press during playback to skip to the beginning of the next track.
: Press during playback to skip to the beginning of the current
track.
R (Rec): Record/Pause
: Reverse playback
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
Note:
Even for devices with the
and
buttons, signal discrepancies
may cause them not to work properly.
46
Using remote controller
Controlling an Integra/Onkyo CD player
The z connector of the Integra/Onkyo compact disc player must be
connected to the DTR-6.2 (see page 16).
1. Press the CD MODE button.
The CD MODE button lights green.
STDBY
ON
CD MODE
DISC
VOL
MUTING
CD
operation
buttons
Numeric keys
HOME THEATER CONTROLLER
RC-441M
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo compact
disc player.
Operation buttons:
ON: Turns on and off the compact disc player (same as STDBY
button on the remote controller).
DISC : Selects a disc in the CD changer
: Track down
: Track up
: Play
: Stop
: Fast reverse
: Fast forward
: Pause
OPEN/CLOSE r: Open/close the disc tray
0, 1 to 9, +10: Numeric keys
RANDOM/R: For random playback.
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
47
Using remote controller
Controlling an Integra/Onkyo DVD player
The z connector of the Integra/Onkyo DVD player must be
connected to the DTR-6.2 (see page 16).
1. Press the DVD MODE button.
The DVD MODE button lights green.
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo DVD
player.
STDBY
ON
DVD MODE
RETURN
SETUP
ENTER/Cursor
button
DISC
VOL
TOP MENU
AUDIO
MENU
MUTING
ANGLE
SUBTITLE
DVD
operation
buttons
Numeric keys
SEARCH
HOME THEATER CONTROLLER
RC-441M
Operation buttons:
ON: Turns the DVD player on and off
STDBY: Turns the DVD player off. (Some sets may not respond to
this button. In this case, use the ON button to put the DVD player in
the standby state.)
SETUP: Displays the menu
: Moves the cursor
ENTER: Confirms the selection
RETURN: Return button
TOP MENU or MENU: Displays the menu screen(s) recorded on
DVD media.
DISC
: Selects a disc in the DVD changer.
AUDIO: Press repeatedly to select an audio and/or language track
recorded on a DVD-Audio/Video.
ANGLE: Press repeatedly to select a camera angle when a DVDVideo is recorded with multiple angle playback.
SUBTITLE: Press repeatedly to select one of the subtitle languages
recorded on a DVD-Video.
SEARCH: Press to find the specific section on a disc where you
want to start playback.
RANDOM/R: Press to start random playback.
: Chapter/Track down
: Chapter/Track up
: Play
: Stop
: Fast reverse
: Fast forward
: Pause
OPEN/CLOSE r: Open/close the disc tray
0, 1 to 9, +10: Numeric keys
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
Note:
When operating an Integra/Onkyo DVD player directly with the
remote controller without connecting the z terminals, preprogramming is necessary (see page 50).
48
Using remote controller
Controlling an Integra/Onkyo MD recorder
The z connector of the Integra/Onkyo MD recorder must be
connected to the DTR-6.2 (see page 16).
1. Press the MD MODE button.
The MD MODE button lights green.
STDBY
ON
MD MODE
VOL
MUTING
MD
operation
buttons
Numeric keys
ENTER
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo MD
recorder.
Operation buttons:
ON: Turns on and off the MD player (same as STDBY button on the
remote controller).
: Track down
: Track up
: Play
: Stop
: Fast reverse
: Fast forward
R (Rec): Record
: Pause
r: Eject the disc
1 to 9, 0, --/---: Numeric keys
ENTER: Enters the settings
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
HOME THEATER CONTROLLER
RC-441M
SAT, CABLE, VCR, and TV MODE buttons
CABLE
SAT
VCR
TV
VOL
MUTING
No preset codes are programmed into the SAT, CABLE, VCR, and
TV MODE buttons. You can use these buttons to program the
remote controller signals of other devices.
There are two methods. One method is selecting the name of a
different brand from the table, entering the setting number listed, and
calling up the pre-programming code (see page 50). The other
method is learning the commands from the other brand’s remote
control directly into this remote controller (see page 54).
When in the SAT, CABLE and VCR mode, you may use the
following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
49
Learning a pre-programming code
The remote controller has three learning functions. One is entering
the signal number for a remote controller of another brand that is preprogrammed. Another is a normal learning function that enables the
remote controller to learn the codes from other remote controllers.
And the last is a macro learning function that enables you to program
a series of operations into the remote controller so that the operations
can all be performed at once by pressing one button.
SEND/LEARN
indicator
Buttons that
can be preprogrammed
Learning a pre-programming code
By learning a pre-programming code, you can make the RC-441M
remote controller able to operate a product from another brand. The
buttons that are used for operation are given on the next page.
1. Find the 3-digit number for the brand name of the
component that you want to operate in the table on
the next page.
2. Turn on the component that you want to operate (i.e.
DVD, satellite tuner, or television).
3. While holding down the MODE button on the RC441M that you want to program, press the DISPLAY
button, and then release both buttons.
The SEND/LEARN indicator lights when the MODE button is
pressed and turns off when the DISPLAY button is pressed. Wait
until the indicator turns off before releasing both buttons. Then
the SEND/LEARN indicator lights again.
4. Within 30 seconds, enter the 3-digit code number.
The SEND/LEARN indicator flashes twice slowly. If the SEND/
LEARN indicator quickly flashes three times, then either a
mistaken 3-digit code was entered or an incorrect operation was
performed. If this occurs, return to step 3.
5. Press the button that you programmed and check if
the system operates correctly.
Numeric keys
DISPLAY
HOME THEATER CONTROLLER
RC-441M
Caution
With some brand’s components, some buttons may not work
correctly. In this case, program the command separately.
50
• If the component does not operate properly, return to step 3
and repeat the steps above.
• If it still does not operate properly, then program the
commands one by one to the buttons on the RC-441M remote
controller.
When entering the code of Integra/Onkyo DVD players:
There are three SETTING numbers. Choose the SETTING number
according to how you will be using the DVD player.
No. 601/613: These codes are for operating the Integra/Onkyo DVD
player by pointing the remote controller directly at it, either because
it does not have an z terminal, or it does but you are not using an
z cable and connecting it. First enter 601 and if it does not operate
properly, enter 613.
No. 600: This code is for Integra/Onkyo DVD players that have an
z terminal that you are connecting to the DTR-6.2 with an z
cable. You will then operate the DVD player by pointing the remote
controller at the remote control sensor on the DTR-6.2. You do not
need to enter this code because it is factory preset. However, if the
code has been changed to 601 or 613, then you will need to change it
back to 600.
Learning a pre-programming code
Pre-programmong codes
Note:
If more than one code is given in the table,
try the code one by one until you reach the
code for your component (i.e. if the first
code does not work, then try the next).
DVD
BRAND
DENON
HITACHI
JVC
KENWOOD
MAGNAVOX
MARANTZ
MITSUBISHI
INTEGRA
ONKYO
PANASONIC
PIONEER
PROSCAN
RCA
SONY
TOSHIBA
YAMAHA
ZENITH
SETTING No.
602, 609
603
604
605
606, 613
607
608, 613
600, 601, 613
600, 601, 613
609
610
611
611
612
613
609, 614
613, 615
SETTING No.
700
701
702
703
704
705
706, 707
706, 707
708
709
CABLE
BRAND
GENERAL
INSTRUMENTS
GEMINI
HAMLIN
JERROLD
MACOM
MAGNAVOX
OAK
PANASONIC
PHILIPS
PIONEER
SCIENTIFIC
ATLANTA
SAMSUNG
TOCOM
ZENITH
BRAND
AIWA
AKAI
BAIRD
BELL & HOWELL
BLAUPUNKT
CGM
COLTINA
DAEWOO
DIGITAL
EMERSON
FENNER
FISHER
FUJITSU GENERAL
FUNAI
GE
GO VIDEO
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
JVC
LOEWE
MAGNAVOX
MITSUBISHI
SAT
BRAND
ECHOSTAR
GENERAL
INSTRUMENTS
HITACHI
HUGHES
NETWORK
SYSTEMS
PANASONIC
PRIMESTAR
PROSCAN
RCA
SONY
TOSHIBA
VCR
SETTING No.
500
501
502, 503, 504, 505
500, 506, 507, 508,
509, 510, 511, 512,
513, 514
515, 516, 517
518
519, 520, 521
522, 523
524, 525, 526, 527,
528, 529
530, 531
532, 533, 534
535
536
537, 538
NEC
NOKIA
NORDMENDE
OKANO
ORION
PANASONIC
PHILIPS
PHONOLA
PIONEER
RCA
SABA
SAMSUNG
SANYO
SCOTT
SELECO
SHARP
SHINTOM
SIEMENS
SONY
SYMPHONIC
TEKNIKA
TELEFUNKEN
TOSHIBA
WHITE
WESTINGHOUSE
WATSON
ZENITH
TV
SETTING No.
300, 301, 302
303, 304, 305, 306,
307
308
309
310
311, 312, 313
314
315, 316
317
318, 319, 320, 321,
322
323
324, 325, 326, 327
BRAND
AIWA
AKAI
AUDIOSONIC
BELL & HOWELL
BLAUPUNKT
BRIONVEGA
CENTURION
COLTINA
CORONAD
CROWN
DAEWOO
328
329
330, 331
332, 336, 337
333, 334
335
338
339, 340, 341
342, 343, 344, 345,
346, 347, 348, 349,
350
351, 352
353, 354, 355
356, 357, 358, 359,
360, 361, 362, 363,
364
365, 366, 367
313
368, 369, 370
371, 372
319, 373
374, 375, 376, 377,
378
353, 379, 380
311
381
382
383
384, 385, 386, 387,
388, 389, 390
391, 392, 393
394
395
396, 397, 398, 399
400
401
402, 403, 404, 405,
406, 407, 408, 409,
410, 411, 412, 413
414
414, 415
416, 417
418, 419, 420
FENNER
FERGUSON
FISHER
FUNAI
FUJITSU GENERAL
GE
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
HYPER
INNO HIT
IRRADIO
JVC
333
421
422
DUAL
EMERSON
KENDO
KTV
LUXOR
MAGNAVOX
MARANTZ
MARK
MATSUI
MITSUBISHI
MIVAR
NEC
NOKIA
OCEANIC
NORDMENDE
OKANO
ORION
PANASONIC
PHILIPS
PIONEER
PROSCAN
QUASAR
RADIO SHACK
RCA
SABA
SAMSUNG
SANYO
SCHNEIDER
SEARS
SELECO
SHARP
SONY
SYMPHONIC
TELEFUNKEN
THOMSON
TOSHIBA
UNIVERSUM
ZENITH
SETTING No.
100, 101
102, 103, 104
105
106
107
108, 109
110
111, 112, 113
114
115, 116
117, 118, 119, 120,
121
122
123, 124, 125, 126,
127
128, 129
130, 131
132
133, 134, 135
136, 137, 138
139, 140, 141
142, 143
144
145, 146
147, 148, 149, 150
151
152
103
153, 154, 155, 156,
157
158
159, 160
161
162, 163
164
165
166, 167, 168, 169
170, 171, 172, 173
174, 175
176, 177
178, 179, 180, 181
181
182, 183
152
184, 185, 186
187, 188, 189, 190
152, 162, 191
192, 193
194
195
196
110, 141, 197, 198,
199, 200
182, 183, 201
202, 203, 204, 205,
206, 207, 208
209, 210, 211, 212
103
213
214, 215
216, 217
218, 219, 220, 221,
222, 223
224, 225
201, 226, 227
228
213, 229
230
231, 232
51
Operating your programmed remote controller
After performing the procedure given above, the following
modes become enabled for use.
DVD MODE (DVD Player Mode)
Buttons with programmed usage and operations are the same as the
operational buttons on page 48.
SAT MODE (Satellite Tuner Mode)
1. Press the SAT MODE button.
The SAT button lights green.
STDBY
ON
SAT MODE
ENTER/Cursor
button
VOL
CH
MUTING
MENU
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your satellite tuner unit.
The buttons given below have operations programmed
into them.
ON: Turns on and off the satellite tuner unit (same as STDBY button
on the remote controller)
CH
: Moves up and down the preset channel numbers
: Moves the cursor
ENTER: Confirms the selection
MENU: Displays the menu
0,1 to 9: Numeric keys
ENTER: Confirm
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
Numeric keys
ENTER
HOME THEATER CONTROLLER
RC-441M
CABLE MODE (Cable Mode)
1. Press the CABLE MODE button.
The CABLE button lights green.
STDBY
ON
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your cable unit.
CABLE MODE
VOL
CH
MUTING
The buttons given below have operations programmed
into them.
ON: Turns on and off the cable unit (same as STDBY button on the
remote controller)
CH
: Moves up and down the preset channel numbers
0,1 to 9: Numeric keys
ENTER: Confirm
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
Numeric keys
ENTER
HOME THEATER CONTROLLER
RC-441M
52
Operating your programmed remote controller
VCR MODE (VCR Mode)
1. Press the VCR MODE button.
The VCR button lights green.
STDBY
ON
VCR MODE
VOL
CH
TV/VCR
MUTING
Video cassette
recorder
operation
buttons
Numeric keys
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your VCR.
The buttons given below have operations programmed
into them.
ON: Turns on and off the VCR (same as STDBY button on the
remote controller)
CH
: Moves up and down the preset channel numbers
TV/VCR: Switches the AV input for the VCR
: Play
: Stop
: Rewind
: Fast Forward
: Pause
0,1 to 9, +10: Numeric keys
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-6.2
MUTING: Activates the muting function at the DTR-6.2
HOME THEATER CONTROLLER
RC-441M
TV MODE (TV Mode)
1. Press the TV MODE button.
The TV button lights green.
STDBY
ON
TV MODE
VOL
CH
TV/VCR
MUTING
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your television.
The buttons given below have operations programmed
into them.
ON: Turns on and off the television (same as STDBY button on the
remote controller)
CH
: Moves up and down the television channels
TV/VCR: Switches the TV/VCR input for the television
0,1 to 9, +10: Numeric keys
ENTER: Confirm
VOL : Adjusts the volume at the television
MUTING: Activates the muting function at the television
Numeric keys
ENTER
HOME THEATER CONTROLLER
RC-441M
53
Programming the commands of remote controllers
for other devices into the remote controller
PE
TA
VD
D
5 to 15 cm
(2 to 6 inches)
IS
D
C
VID
-1
ER
W
PO
D
VD
VID
P
EE
SL
T
EO
P
IN
E
AP
EO
D
-2
C
R
G
O
U
P
O
N
R O
TO PH
C
LE R
SE E
T N
U TU
D
ER
M
IM
RE
SUOD
M
CH
TI- T
UL PU
M IN
C
D
S
ER E
N PR
TU
ET
C
H
SE
L
ST E
TEON
T
U
M
TIN
G
LU
VO
E
M
S
85
Programming procedure
When programming the commands of another remote controller to
the RC-441M remote controller, you must first decide under which
MODE button you want the commands to be linked. In general, you
will select the MODE button that corresponds to the component you
are programming. For example, if you are programming the
functions from a remote controller for a compact disc player, you
would choose the CD MODE button. Then, by pressing the CD
MODE button, the buttons on the RC-441M remote controller will
change to the commands you program here to operate the compact
disc player.
After programming which MODE button to use, you will then
transfer the separate commands from the other remote controller
over to the RC-441M remote controller one at a time. Each
command is then programmed to a different button on the RC-441M
remote controller. Any button is programmable for this step except
for the eight MODE buttons (RCVR, CD, DVD, MD, SAT, CABLE,
VCR, and TV), the two MACRO buttons (DIRECT and MODE),
and the LIGHT button.
Even after the commands have been memorized, keep your old
remote controller in a safe place. If for some reason the commands
are lost (e.g., when the batteries run down), it will be necessary to
memorize them once again.
1. Place the remote controller and the remote controller
for the other device facing each other at a distance of
5 to 15 cm (2 to 6 inches) apart.
SEND/LEARN
indicator
MODE
buttons
2. While pressing and holding down the desired MODE
button on the remote controller, press the ENTER
button and then release both buttons.
When you press and hold down the MODE button, the SEND/
LEARN indicator lights. When you press the ENTER button, the
lamp turns off. When you release the buttons, the lamp lights
again.
3. Press and release the button on the remote controller
to which you want to transfer the next command.
You may select any button but the eleven ones indicated in the
figure below. When you press the button, the SEND/LEARN
indicator turns off. When you release the button, the indicator
lights again.
If you press the wrong button by mistake, press that same button
again. The SEND/LEARN indicator flashes twice, and the
remote controller exits the programming mode.
LIGHT
MODE DIRECT
MODE MACRO
MODE buttons
ENTER
HOME THEATER CONTROLLER
RC-441M
54
: Buttons that cannot be programmed.
Programming the commands of remote controllers for other devices into the
remote controller
4. Press and hold down the button (that corresponds to
the command you are programming) on the remote
controller of the other device until the SEND/LEARN
lamp on the remote controller flashes twice.
After flashing twice, the SEND/LEARN indicator will light
again.
5. Repeat Steps 3 and 4 to transfer all the commands
you desire from the other remote controller and
program them to buttons on the remote controller
under the same MODE.
Repeat Steps 2 through 4 to program commands to a different
MODE (e.g., when programming from a different remote
controller).
6. Press the MODE button that you pressed in step 2 to
complete the programming.
7. Operate the newly programmed buttons to make sure
the learning function was performed properly.
Notes:
• The remote controller codes for Integra/Onkyo compact disc
players, cassette tape decks, DVD players, and mini disc
recorder have already been programmed into buttons on the
remote controller. You may, however, use these buttons to
program the codes for other remote controllers. If you wish to
restore the Integra/Onkyo preset codes after you program new
codes, you must first erase the new codes (see page 56).
• The remote controller has 408 memory slots (8 modes × 51
buttons). Some remote controllers may have more commands
that can be remembered by the remote controller. In such cases,
it will be necessary for you to determine which commands are
more important than others.
• If no button is pressed for more than 30 seconds during the
programming, or if you perform an invalid operation during
programming, the SEND/LEARN indicator flashes three times
quickly, and the remote controller exits the programming mode.
Resume from Step 2.
• If a failure occurs during programming, the SEND/LEARN
indicator flashes three times quickly, and the remote controller
exits the programming mode. Resume from Step 3.
• If a failure occurs five times in row during programming, the
remote controller exits the programming mode. Resume from
Step 3.
• If you try to program beyond the learning capacity of the remote
controller, the SEND/LEARN indicator flashes six times
quickly, and the remote controller exits the programming mode.
Try programming under a different MODE button.
• When you want to program a command to a button to which you
have already programmed a command, simply follow the same
procedure given and programming for that button will be
overwritten.
• The remote controller uses infrared rays to send its commands,
as do most other remote controllers. Though most remote
controller codes can be memorized by the remote controller, be
aware that some remote controllers use a system that is quite
different from the remote controller and therefore may not be
able to be programmed.
• Some remote controllers have a single button that performs
multiple functions (for example, the function may change each
time the button is pressed). If this is the case, each function must
be programmed to a separate button on the remote controller.
• Once you have transferred the commands from the other remote
controller, refer to the instruction manual that came with that
product for instructions on how to operate that product.
• Make sure both the remote controller and the other remote
controller have new batteries. If either of them has batteries that
are low, you may not be able to program the commands of the
other remote controller properly into the remote controller.
See page 56 for how to erase the memorized commands from all
buttons.
55
Programming the commands of remote controllers for other devices into the
remote controller
SEND/LEARN
indicator
Erasing the programmed command from one
button
You can only erase memorized commands and not preset ones.
MODE
buttons
1. Press and hold down the desired MODE button for
the command, press the ENTER button, and then
release both buttons.
When you press the MODE button, the SEND/LEARN indicator
lights. When you press the ENTER button, the lamp turns off.
When you release the buttons, the lamp lights again.
2. Press and release the button for the command you
wish to erase.
When you press the button, the SEND/LEARN indicator turns
off. When you release the button, the lamp lights again.
3. Press and release the same button again.
The SEND/LEARN lamp flashes twice slowly. The memorized
command is erased.
Note:
If no button is pressed for more than 30 seconds during the erasing
procedure, the SEND/LEARN indicator flashes three times quickly,
and the remote controller exits the erasing mode. Resume from Step
1.
ENTER
HOME THEATER CONTROLLER
RC-441M
SEND/LEARN
indicator
MODE
buttons
Erasing all the commands programmed under a
MODE button
1. Press and hold down the desired MODE button,
press the ENTER button twice, and then release both
buttons.
When you press the MODE button, the SEND/LEARN indicator
lights. When you press the ENTER button, the lamp turns off.
When you release the buttons, the lamp flashes twice slowly and
then lights again.
2. Press and release the same MODE button again.
When you release the button, the SEND/LEARN indicator
flashes twice slowly. This erases all the commands memorized
to the MODE button.
ENTER
HOME THEATER CONTROLLER
RC-441M
56
Notes:
• If no button is pressed for more than 30 seconds during the
erasing procedure, the SEND/LEARN indicator flashes three
times quickly and the remote controller exits the erasing mode.
Resume from Step 1.
• If you perform an invalid operation during erasing, the SEND/
LEARN indicator flashes three times quickly, and the remote
controller exits the erasing mode. Resume from Step 1.
• If many commands have been programmed to the MODE
button, then the SEND/LEARN indicator may remain lit for up
to 20 seconds during Step 2. This is not a malfunction.
Using a Macro function
What is a Macro function?
Programming a Macro function
A Macro function enables you to program a series of button
operations (up to 16) on the remote controller into a single button.
For example, to play a compact disc player connected to the DTR6.2 normally, you must perform the following steps:
1. Press the RCVR MODE button.
2. Press the ON button.
3. Press the CD (INPUT SELECTOR) button.
4. Press the CD MODE button.
5. Press the playback (
) button.
By using the macro function, you can perform the above five
operations by only pressing two buttons.
ON
MODE MACRO
CD MODE
RCVR MODE
You can program a different macro into the MODE MACRO button
for each of the eight MODE buttons. The macro is then executed by
pressing the appropriate MODE button and then pressing the MODE
MACRO button. For example, to program the macro described
above into the CD MODE button, perform the steps given below.
1. Press and hold down the desired MODE button (in
this case, the CD MODE button), press the MODE
MACRO button, and then release both buttons.
When you press the CD MODE button, the SEND/LEARN
indicator lights and the CD MODE button lights green. When
you press the MODE MACRO button, the indicator turns off.
When you release the buttons, the indicator flashes and lights
again.
2. Press the operation buttons you wish to program in
order (in this case, press RCVR MODE → ON → CD
(INPUT SELECTOR) → CD MODE → playback ( )
button).
When you press each button, the SEND/LEARN indicator turns
off. When you release the button, the indicator lights.
3. Press the MODE MACRO button to complete the
programming.
The SEND/LEARN indicator flashes twice slowly.
4. Run the macro to check to see if the macro has been
properly programmed.
(CD playback)
CD
(INPUT
SELECTOR)
HOME THEATER CONTROLLER
RC-441M
Tips:
• If you erase or change the command of a button programmed in
a macro, that operation of that button will no longer work in the
macro. In this case, it will be necessary for you to reprogram the
macro in order to avoid incorrect operation.
• The codes programmed into a macro will be transmitted at an
interval of 0.5 seconds. However, some devices may not be able
to complete one operation in 0.5 seconds and may miss the next
code. In this case, after pressing one operation button, you can
press the same MODE button again before pressing the next
operation button to add another 0.5 seconds between the two
operations.
Notes:
• You may program up to 16 button operations into each macro
function. If you try to program a 17th operation, it will be
ignored, and programming is stopped.
• If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three times
quickly, and the remote controller exits the programming mode.
Resume from Step 1.
• If you perform an invalid operation during programming, the
SEND/LEARN indicator flashes three times quickly, and the
remote controller exits the programming mode. Resume from
Step 1.
Running a Macro function
Perform the procedure below to run a macro function that you have
programmed into the remote controller. After programming a macro,
you should always run it at least once to make sure that it has been
programmed properly.
1. Point the remote controller at the DTR-6.2 and press
the CD MODE button.
2. Press the MODE MACRO, and verify that the devices
operate properly.
It may take a while for the macro to finish transmitting, so be
sure to continue pointing the remote controller at the device until
the SEND/LEARN indicator turns off.
57
Using a Macro function
Programming the Direct Macro function
ON
DIRECT MACRO
CD MODE
MODE buttons
RCVR MODE
With the direct macro function, you can program a series of button
operations as a macro into the DIRECT MACRO button so the
macro can be executed with just one touch. Note that for the direct
macro function, only one macro can be programmed. For example,
to program the macro described on the previous page for the
DIRECT MACRO button, perform the steps given below.
1. Press and hold down any one of the eight MODE
buttons, press the DIRECT MACRO button, and then
release both buttons.
When you press the MODE button, it lights green and the
SEND/LEARN indicator lights. When you press the DIRECT
MACRO button, the indicator turns off. When you release the
buttons, the indicator flashes briefly and then lights again.
(CD playback)
CD
(INPUT
SELECTOR)
2. Press the operation buttons you wish to program in
order (in this case, press RCVR MODE → ON → CD
(INPUT SELECTOR) → CD MODE → playback ( )
button).
When you press each button, the SEND/LEARN indicator turns
off. When you release the button, the indicator lights.
3. Press the DIRECT MACRO button to complete the
procedure.
The SEND/LEARN indicator flashes twice slowly.
HOME THEATER CONTROLLER
RC-441M
Tips:
• If you erase or change the command of a button programmed in
the direct macro, that operation of that button will no longer
work in the macro. In this case, it will be necessary for you to
reprogram the direct macro in order to avoid incorrect operation.
• The codes programmed into a direct macro will be transmitted at
an interval of 0.5 seconds. However, some devices may not be
able to complete one operation in 0.5 seconds and may miss the
next code. In this case, after pressing one operation button, you
can press the same MODE button again before pressing the next
operation button to add another 0.5 seconds between the two
operations.
4. Check to see if the macro has been properly
programmed.
Notes:
• You may program up to 16 button operations into the direct
macro function. If you try to program a 17th operation, it will be
ignored, and programming is stopped.
• If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three times
quickly, and the remote controller exits the programming mode.
Resume from Step 1.
• If you perform an invalid operation during programming, the
SEND/LEARN indicator flashes three times quickly, and the
remote controller exits the programming mode. Resume from
Step 1.
Running a Direct Macro function
Perform the procedure below to run a direct macro function that you
have programmed into the remote controller. After programming a
direct macro, you should always run it at least once to make sure that
it has been programmed properly.
1. Point the remote controller at the DTR-6.2 and press
the DIRECT MACRO button.
It may take a while for the macro to finish transmitting, so be
sure to continue pointing the remote controller at the device until
the SEND/LEARN indicator turns off.
58
Using a Macro function
Erasing a macro from the MODE MACRO button
MODE MACRO
MODE buttons
1. Press and hold down the desired MODE button,
press the MODE MACRO button, and then release
both buttons.
When you press the MODE button, it lights green and the
SEND/LEARN indicator lights. When you press the MODE
MACRO button, the indicator turns off. When you release the
buttons, the indicator flashes once.
2. Press the MODE MACRO button again.
The SEND/LEARN indicator flashes twice slowly. The macro
programmed to the MODE button pressed in Step 1 above is
erased.
Notes:
• If no button is pressed for more than 30 seconds during the
erasing procedure, the SEND/LEARN indicator flashes three
times quickly, and the remote controller exits the erasing mode.
Resume from Step 1.
• Be aware that if you press a button other than MODE MACRO
button in Step 2, then you will in effect be overwriting the
previous macro with a new macro.
HOME THEATER CONTROLLER
RC-441M
Erasing a direct macro from the DIRECT
MACRO button
DIRECT MACRO
MODE buttons
1. Press and hold down any one of the eight MODE
buttons, press the DIRECT MACRO button, and then
release both buttons.
When you press the MODE button, it lights green and the
SEND/LEARN indicator lights. When you press the DIRECT
MACRO button, the indicator turns off. When you release the
buttons, the indicator flashes once.
2. Press the DIRECT MACRO button again.
The SEND/LEARN indicator flashes twice slowly. The macro
programmed to the DIRECT MACRO button is erased.
Notes:
• If no button is pressed for more than 30 seconds during the
erasing procedure, the SEND/LEARN indicator flashes three
times quickly, and the remote controller exits the erasing mode.
Resume from Step 1.
• Be aware that if you press a button other than DIRECT MACRO
button in Step 2, then you will in effect be overwriting the
previous direct macro with a new direct macro.
HOME THEATER CONTROLLER
RC-441M
59
Using a Macro function
Erasing all commands and macros that have
been programmed
This procedure will erase all the commands and macros that you
have programmed into the remote controller and return it to its
default settings. This operation will not affect the preset settings of
the remote controller.
STDBY
ON
1. Open the battery cover and remove the batteries from
the remote controller.
2. While pressing and holding down the ON and STDBY
buttons, re-insert the batteries in their correct
orientation, and then release both buttons.
The SEND/LEARN indicator flashes slowly.
3. Press the ENTER button.
The SEND/LEARN indicator lights up for about ten seconds and
then turns off.
All programmed commands and macros are erased and the remote
controller returns to its factory presets.
Notes:
• Proceed to Step 3 immediately after Step 2; otherwise, the
batteries will be consumed quickly.
• If you press any button other than the ENTER button in Step 3,
nothing will be erased. In this case, resume from Step 1.
ENTER
HOME THEATER CONTROLLER
RC-441M
Macro mode programming memo:
MACRO
Operation 1
Operation 2
Operation 3
Operation 4
Operation 5
Operation 6
Operation 7
Operation 8
Operation 9
Operation 10
Operation 11
Operation 12
Operation 13
Operation 14
Operation 15
Operation 16
60
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
DIRECT
MACRO
MACRO
MACRO
MACRO
MACRO
MACRO
MACRO
MACRO
MACRO
↓
↓
↓
↓
↓
↓
↓
↓
RCVR
CD
DVD
MD
SAT
CABLE
VCR
TV
Specifications
AMPLIFIER SECTION
Continuous Average Power output (FTC)
All channels:
100 W per channel min. RMS at 8
Ω, 2 channels driven from 20 Hz
to 20 kHz with no more than
0.08% total harmonic distortion.
125 W min. RMS at 6 Ω, 2
channels driven from 1 kHz with
no more than 0.1% total
harmonic distortion.
Continuous Power output (DIN) 130 W at 6 Ω
Maximum Power output (EIAJ) 160 W at 6 Ω
Dynamic Power Output (Stereo) 2 × 230 W at 3 Ω
2 × 170 W at 4 Ω
2 × 115 W at 8 Ω
Total Harmonic Distortion:
0.08% at rated power
0.08% at 1 W output
IM Distortion:
0.08% at rated power
0.08% at 1 W output
Damping Factor:
60 at 8 Ω
Input Sensitivity and Impedance
PHONO:
2.5 mV, 50 kΩ
LINE (CD, TAPE, DVD,
VIDEO 1-4):
200 mV, 50 kΩ
MULTICHANNEL INPUT
(FRONT L/C/R, SURROUND L/R):
200 mV, 50 kΩ
(SUBWOOFER):
36 mV, 50 kΩ
COAXIAL 1, 2 (DIGITAL):
0.5 Vp-p, 75 Ω
DVD, VIDEO1-4:
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
COMPONENT VIDEO 1, 2: 1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (CB/CR, PB/PR)
Output Level and Impedance
Rec out (TAPE, VIDEO 1, 2): 200 mV, 2.2 kΩ
Pre out:
1 V, 470 Ω
VIDEO (VIDEO 1, 2, MONITOR OUT):
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
COMPONENT VIDEO OUT: 1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (CB/CR, PB/PR)
ZONE 2 LINE OUT:
100 mV, 1 kΩ
110 mV RMS at 1 kHz, 0.5% T.H.D.
Phono Overload:
Frequency Response:
5 Hz to 100 kHz: +1 dB, –3 dB
RIAA Deviation:
20 Hz to 20 kHz : ±0.8 dB
Tone Control
Bass:
±10 dB at 50 Hz
Treble:
±10 dB at 20 kHz
Signal-to-Noise Ratio (Stereo)
Phono:
80 dB (IHF A, 5 mV input)
CD/Tape:
100 dB (IHF A, 0.5 V input)
Muting:
–50 dB
TUNER SECTION
FM
Tuning Range:
Usable Sensitivity
Mono:
Stereo:
50 dB Quieting Sensitivity
Mono:
Stereo:
Capture Ratio:
Image Rejection Ratio:
IF Rejection Ratio:
Signal-to-Noise Ratio
Mono:
Stereo:
Alternate Channel Attenuation:
Selectivity:
AM Suppression Ratio:
Total Harmonic Distortion
Mono:
Stereo:
Frequency Response:
Stereo Separation:
87.5 to 108.0 MHz (50-kHz steps)
11.2 dBf, 1.0 µV (75 Ω IHF)
0.9 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω IHF)
23 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω)
37.2 dBf, 20 µV (75 Ω)
2.0 dB
40 dB
90 dB
76 dB
70 dB
55 dB
50 dB (DIN)
50 dB
0.2%
0.3%
30 Hz to 15 kHz, ±1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz to 10 kHz
AM
Tuning Range:
Usable Sensitivity:
Image Rejection Ratio:
IF Rejection Ratio:
Signal-to-Noise Ratio:
Total Harmonic Distortion:
530 to 1,710 kHz (10-kHz steps)
30 µV
40 dB
40 dB
40 dB
0.7%
GENERAL
Power Supply:
Power Consumption:
Dimensions (W × H × D):
Weight:
AC 120 V, 60 Hz
5.7 A
17-1/8" × 6-7/8" × 17"
28.0 lbs.
REMOTE CONTROLLER
Transmitter:
Signal range:
Power supply:
Infrared
Approx. 5 meters, 16 ft.
Two “AA” batteries (1.5 V × 2)
Specifications and features are subject to change without notice.
Power supply and voltage vary depending on the area in which the
unit is purchased.
61
Troubleshooting guide
If a problem occurs while you are using the remote controller, first
try to operate the controls on the front panel of the DTR-6.2 to make
sure that it is not due to a malfunction (or worn out batteries) in the
remote controller.
POWER
Power shuts off immediately after power on.
• Amplifier protection circuitry has been activated.
➞ Remove the power cord from outlet immediately. Contact
your Integra/Onkyo authorized service center.
No power.
• Power cord is disconnected.
➞ Connect power cord.
• External noise in the affecting the internal microcomputer.
➞ Turn the power button off and then on again or remove the
power cord from the outlet and then plug it in again.
• Internal fuse is blown.
➞ Contact your Integra/Onkyo authorized Service Center.
Power turns on but no sound.
• “Muting” is displayed.
➞ Press the MUTING button on the remote controller to turn it
off.
• Bad connections or wiring.
➞ Check connections, speaker cables, etc.
• Amplifier protection circuitry has been activated.
➞ Contact your Integra/Onkyo authorized Service Center.
The sound of the playback source is not heard.
• Input selector is not set properly.
➞ Set to correct input source.
• Headphones are connected.
➞ Lower volume and then disconnect headphones.
SPEAKERS
No sound from the center speaker, or at very low
volume.
• Speaker cable is not connected.
➞ Check the connection between the amplifier and the speaker.
• Listening mode is set to Stereo or Direct.
➞ Set the Listening mode to any mode other than Stereo or
Direct. The output to the center speaker may differ depending
on the listening mode.
• Center speaker level is set to minimum.
➞ Set the Center speaker level to the appropriate volume (page
24, 25).
• The Center setting of the Speaker Config submenu is set to
“None.”
➞ Set the Center setting at the Speaker Config submenu to
“Large” or “Small” (see pages 24, 25).
No sound or very low volume from subwoofer.
• Subwoofer is set to “No.”
➞ Check the speaker setting (pages 24, 25).
• Subwoofer speakers output level setting is improper.
➞ Check the output level of the Subwoofer using the test tone.
Low frequency humming is heard.
• Not properly grounded.
➞ Check outer conductor of input plugs.
62
• Turntable motor is not properly grounded.
➞ Check for proper ground connection.
• Audio connection cables on the rear panel are connected
incorrectly.
➞ Adjust the placement of the cable to reduce hum.
Howling is heard when the volume is turned up.
• Turntable and speakers are located too close together.
➞ Move them farther apart.
Rough or scratchy sound is heard. High range is not
clear.
• The needles of turntable is dirty or worn, or a problem exists
with a connected component.
➞ Refer to the instruction of the connected components and
check for problem.
• Treble control is too high.
➞ Turn treble down.
FM/AM TUNER
AM stations cannot be received.
• AM loop antenna is not connected.
➞ Connect the included AM loop antenna to the AM antenna
terminals.
Buzzing noise on AM stations (particularly noticeable at
night or with weak stations).
• Noise from electrical apparatus such as fluorescent lamp.
➞ Move the AM loop antenna to different position.
➞ Set up an outdoor AM antenna.
Noise is heard at high-pitched sounds on AM stations.
• Noise from TV set.
➞ Place the AM loop antenna as far as possible from the TV.
➞ Move unit away from TV set.
Crackling noise on both AM and FM stations.
• Noise caused by fluorescent lamp being turned on and off.
➞ Move antenna as far as possible from the fluorescent lamp.
• Noise from automobile ignition.
➞ Install an FM outdoor antenna as far as possible from the
road.
➞ Change the position or direction of the outdoor antenna.
The indicators light for stereo reception, but sound is
distorted and stereo separation is bad.
• Station is too strong.
➞ Change to FM indoor antenna.
• Multiple reflection of the radio waves because of tall buildings
or mountains.
➞ Use antenna that has better directivity and select a point
where distortion is least.
Indicators for stereo reception flicker and hiss is heard
on FM stations.
• Station is too weak.
➞ Install an outdoor FM antenna.
• Stereo FM broadcasts cover only about half the distance of an
ordinary broadcast.
➞ Change the position or direction of the outdoor antenna.
No preset station is recalled.
• Power cord has been unplugged or the POWER switch has been
turned off for a long time.
➞ The memory contents are lost. Store all stations again.
Troubleshooting guide
VIDEO and AUDIO
Desired picture does not appear.
• Improper connection.
➞ Check the connection again. Insert the plugs and connectors
completely.
No OSD Menu display.
• Improper connection.
➞ Check connections.
• OSD Menu is displayed when monitor is connected to VIDEO or
S VIDEO of MONITOR OUT.
➞ Confirm connections.
No sound, or sound of the selected source is not heard.
• Audio Setup sub-menu of Input Setup menu settings are
incorrect.
➞ Check settings.
No picture appears on the TV screen (or monitor).
• TV (or monitor) is not set to receive the output signals from the
receiver.
➞ Set the TV (or monitor) to the receiver input.
• Video cable is not connected securely.
➞ Check connections.
• You have connected to the COMPONENT VIDEO connectors
but the DTR-6.2 is not set properly.
➞ Check the Video Setup submenu of the Input Setup menu
(page 38).
REMOTE CONTROLLER
Front panel controls function but remote controller
controls do not.
• No batteries in remote controller.
➞ Insert batteries.
• Batteries have worn out.
➞ Replace batteries.
• Remote controller is not pointed at the remote sensor of the
DTR-6.2.
➞ Point the remote controller at the remote sensor of the DTR6.2.
• Remote controller is too far from the DTR-6.2.
➞ Operate the remote controller within 16 feet.
• Remote controller is functioning in a different mode
➞ Press the RCVR MODE button.
OTHER
LATE NIGHT function cannot be used.
• Playback source is not Dolby Digital encoded.
➞ Check that the DOLBY DIGITAL indicator lights up on the
display.
Re-EQ function cannot be used.
• Re-EQ is only enabled for Analog/PCM sources and Dolby
Digital surround.
➞ See page 33.
Parameter cannot be set for Front Effect etc.
• Parameter may not be able to be set depending on the listening
mode.
➞ See table on page 41.
Multichannel audio is not output.
• To listen to multichannel audio, “Yes” must be selected in the
“Multichannel” in the Audio setup sub-menu of the Input Setup
menu. Also, it is necessary to select Multichannel with the
AUDIO SELECTOR button.
➞ Check that the component is connected to the MULTI
CHANNEL INPUT port and check the Setup menu settings.
Components in remote zone (Zone 2) do not operate
properly.
• Components are incorrectly connected.
➞ Check connections.
• Objects are interfering with remote controller signals.
➞ Move inferring objects away from path of remote controller
signals.
If one of the messages shown below appears
“Not available with headphones use”
The operation is not allowed because headphones are plugged into
the DTR-6.2.
“Not available with Multichannel use”
The operation is not allowed because the selected input source is set
for multichannel input.
“Not available in this Sp Config”
The operation is not allowed by the current speaker configuration.
“Not available in Zone 2 mode”
The operation is not allowed because the Zone 2 mode is turned on.
“Only available with Dolby D”
No setting other than Dolby Digital can be set.
“Not available in this Listening mode”
This operation cannot be performed in this listening mode.
“Not available with this signal”
This operation cannot be performed with this input signal.
“Powered Zone 2 is not activated”
This appears if you try to operate the DTR-6.2 in the remote zone
(Zone 2) even though “Not Activated” is selected for Powered Zone
2 Setup → Powered Zone 2 in the Setup menu. To use the DTR-6.2
in the remote zone, set Powered Zone 2 to “Activated.”
“Zone 2 is Not On”
This appears if you try to operate the DTR-6.2 in the remote zone
(Zone 2) even though the power is not turned on at the remote zone.
Press the ZONE 2 button on the remote controller and then press the
ON button.
Also refer to the respective instruction manuals of the compact disc
player, DVD player, video cassette recorder, TV monitor, etc., that
compose your entertainment system.
The DTR-6.2 contains an internal microcomputer that performs
high-level operations. However, on extremely rare occasions, noise
or interference from an external source or static electricity may cause
faulty operation. If this occurs, unplug the power cord from the wall
outlet, wait five or more seconds, and then plug it back in. This
should correct the situation.
* To reset the surround mode and other settings to the factory
default settings, hold down the Preset Memory button with the
DTR-6.2 turned on and then press the Standby/On button.
“CLEAR” appears in the front display and the DTR-6.2 enters
the standby state.
63
Integra Division of
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 E-mail: integra@onkyousa.com
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
SN 29343021A
D0104-2
E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising