Vaillant ecoTEC plus combi store Installation Manual

Vaillant ecoTEC plus combi store Installation Manual
Installation and maintenance instructions
For the competent person
Installation and maintenance instructions
ecoTEC plus
VUI
GB, IE
Publisher/manufacturer
Vaillant GmbH
Berghauser Str. 40
D-42859 Remscheid
Tel. +49 21 91 18‑0
Fax +49 21 91 18‑28 10
info@vaillant.de
www.vaillant.de
Contents
Contents
7.3
Running the installation assistants ...................... 20
7.4
Restarting the installation assistants ................... 21
1
Safety .................................................................... 4
7.5
Test programmes................................................. 21
1.1
Action-related warnings ......................................... 4
7.6
Performing a gas family check ............................ 21
1.2
Intended use ......................................................... 4
7.7
Using check programmes .................................... 22
1.3
General safety information .................................... 4
7.8
1.4
Related documents................................................ 6
Checking and treating the heating water/filling
and supplementary water .................................... 22
1.5
Related documents................................................ 8
7.9
Preventing low water pressure ............................ 23
2
Notes on the documentation .............................. 9
7.10
2.1
Observing other applicable documents ................. 9
Flushing the heating installation for the first
time ("cold") ......................................................... 23
2.2
Storing documents................................................. 9
7.11
Filling the heating installation .............................. 24
2.3
Validity of the instructions ...................................... 9
7.12
Purging the heating installation ........................... 24
2.4
Benchmark............................................................. 9
7.13
Filling and purging the hot water system ............. 24
2.5
Local regulations.................................................... 9
7.14
Filling the condensate trap .................................. 25
3
Product description............................................. 9
7.15
Gas ratio setting................................................... 25
3.1
Design of the product............................................. 9
7.16
Checking function and leak-tightness.................. 27
3.2
Information on the identification plate.................. 10
7.17
3.3
Serial number ...................................................... 10
Thoroughly flushing the heating installation
("hot")................................................................... 28
3.4
CE label ............................................................... 10
8
Adapting the unit to the heating
installation.......................................................... 28
3.5
Energy Saving Trust Endorsed Products ............ 11
8.1
Burner anti-cycling time ....................................... 28
4
Installation.......................................................... 11
8.2
Setting the maintenance interval ......................... 29
4.1
Unpacking the product......................................... 11
8.3
Setting the pump output....................................... 29
4.2
Checking the scope of delivery............................ 11
8.4
Setting the bypass valve...................................... 29
4.3
Transporting the product ..................................... 11
8.5
Handing the product over to the operator............ 29
4.4
Dimensions .......................................................... 12
9
Troubleshooting ................................................ 30
4.5
Minimum clearances............................................ 12
9.1
Checking service messages ................................ 30
4.6
Clearance from combustible components ........... 12
9.2
Rectifying faults ................................................... 30
4.7
Using the installation template............................. 12
9.3
Calling up and clearing the fault memory ............ 30
4.8
Wall-mounting the product................................... 13
9.4
Resetting parameters to factory settings ............. 30
4.9
Removing the front casing ................................... 13
9.5
Preparing the repair work .................................... 30
4.10
Removing the side section .................................. 13
9.6
Replacing defective components......................... 30
5
Installation.......................................................... 14
9.7
Completing repair work........................................ 36
5.1
Installation requirements ..................................... 14
10
Inspection and maintenance ............................ 36
5.2
Installing the gas connection ............................... 15
10.1
Function menu ..................................................... 36
5.3
Installing the hot and cold water connection........ 15
10.2
Electronics self-test.............................................. 36
5.4
Installing pipe connections between the shiftload cylinder and the heat generator ................... 15
10.3
Removing the compact thermal module .............. 36
Connecting the heating flow and heating
return ................................................................... 15
10.4
Cleaning the heat exchanger............................... 37
10.5
Checking the burner ............................................ 38
10.6
Cleaning the condensate trap.............................. 38
10.7
Cleaning the filter in the cold water inlet.............. 38
10.8
Installing the compact thermal module ................ 38
10.9
Draining the product ............................................ 39
10.10
Checking the pre-charge pressure for the
internal expansion vessel on the heat
generator ............................................................. 39
10.11
Checking the pre-charge pressure of the shiftload cylinder expansion vessel............................ 39
10.12
Completing inspection and maintenance work .... 39
11
Decommissioning.............................................. 39
11.1
Temporarily decommissioning the product.......... 39
5.5
5.6
Connecting the condensate drain pipework ........ 16
5.7
Installing the discharge pipe on the expansion
relief valve............................................................ 16
5.8
Connecting the flexible hose to the expansion
relief valve on the shift-load cylinder ................... 16
5.9
Flue gas installation ............................................. 17
5.10
Electrical installation ............................................ 18
6
Operation............................................................ 20
6.1
Operating concept ............................................... 20
6.2
Calling up the installer level ................................. 20
6.3
Live Monitor (status codes) ................................. 20
6.4
Setting the hot water temperature ....................... 20
7
Start-up ............................................................... 20
7.1
Carrying out the initial start-up............................. 20
7.2
Switching the product on and off ......................... 20
2
11.2
Decommissioning the product ............................. 40
12
Recycling and disposal..................................... 40
13
Customer service............................................... 40
Installation and maintenance instructions ecoTEC plus 0020209593_01
Contents
Appendix ............................................................................ 41
A
Installer level – Overview .................................. 41
B
Overview of diagnostics codes ........................ 43
C
Status codes – Overview .................................. 47
D
Overview of fault codes .................................... 48
E
Connection diagrams ........................................ 52
E.1
Connection diagram, product with integrated
hot water generation, ≥ 37 kW............................. 52
F
Inspection and maintenance work –
Overview............................................................. 53
G
Commissioning Checklist................................. 55
H
Opening of the flue pipe.................................... 59
H.1
Positioning of the opening of a fan-supported
flue gas pipe ........................................................ 59
I
Text from BS 5440-1 on fan-supported flue
gas pipes ............................................................ 60
J
Opening of the flue pipe below eaves and
balconies ............................................................ 60
K
Technical data.................................................... 60
Index ................................................................................... 64
0020209593_01 ecoTEC plus Installation and maintenance instructions
3
1 Safety
1
1.1
Safety
Action-related warnings
Classification of action-related warnings
The action-related warnings are classified in
accordance with the severity of the possible
danger using the following warning signs and
signal words:
Warning symbols and signal words
Danger!
Imminent danger to life or risk of
severe personal injury
Danger!
Risk of death from electric shock
Warning.
Risk of minor personal injury
Caution.
Risk of material or environmental
damage
1.2
Intended use
There is a risk of injury or death to the user or
others, or of damage to the product and other
property in the event of improper use or use
for which it is not intended.
The product is intended as a heat generator
for closed heating installations and for hot
water generation.
The products referred to in these instructions
must only be installed and operated in conjunction with the air/flue pipe accessories listed in other applicable documents.
Exceptions: For C63 and B23P installation
types, follow the specifications in these instructions.
Intended use includes the following:
– observance of accompanying operating,
installation and servicing instructions for
the product and any other system components
– installing and fitting the product in accordance with the product and system approval
– compliance with all inspection and maintenance conditions listed in the instructions.
Any other use that is not specified in these
instructions, or use beyond that specified in
4
this document shall be considered improper
use. Any direct commercial or industrial use
is also deemed to be improper.
Caution.
Improper use of any kind is prohibited.
1.3
General safety information
1.3.1 Risk caused by inadequate
qualifications
Assembly and disassembly, installation, startup, maintenance, repairs and decommissioning must only be carried out by a competent person who is sufficiently qualified to observe all of the instructions that come with the
product, to proceed in accordance with the
current state of the art, and to comply with
all applicable directives, standards, laws and
other regulations.
1.3.2 Risk of death from escaping gas
What to do if you smell gas in the building:
▶ Avoid rooms that smell of gas.
▶ If possible, open doors and windows fully
and ensure adequate ventilation.
▶ Do not use naked flames (e.g. lighters,
matches).
▶ Do not smoke.
▶ Do not use any electrical switches, mains
plugs, doorbells, telephones or other communication systems in the building.
▶ If it is safe to do so, close the emergency
control valve or the main isolator.
▶ If possible, close the gas isolator cock on
the product.
▶ Warn other occupants in the building by
yelling or banging on doors or walls.
▶ Leave the building immediately and ensure
that others do not enter the building.
▶ Notify the gas supply company or National
Grid Transco +44 (0) 800 111999 by telephone from outside of the building.
1.3.3 Risk of death from leaks if the
product is installed below ground
level!
Liquid gas is accumulating at floor level. If the
product is installed below ground level, liquid
gas may accumulate at floor level if there
Installation and maintenance instructions ecoTEC plus 0020209593_01
Safety 1
are any leaks. In this case, there is a risk of
explosion.
▶ Make sure that liquid gas cannot escape
from the product or the gas line under any
circumstance.
1.3.4 Risk of death due to blocked or
leaking flue gas routes
Installation errors, damage, tampering, unauthorised installation sites or similar can cause
flue gas to escape and result in a risk of poisoning.
What to do if you smell flue gas in the property:
▶ Open all accessible doors and windows
fully to provide ventilation.
▶ Switch off the product.
▶ Check the flue gas routes in the product
and the flue gas diversions.
1.3.5 Risk of poisoning and burns caused
by escaping hot flue gases
▶ Only operate the product if the air/flue pipe
has been completely installed.
▶ With the exception of short periods for
testing purposes, only operate the product
when the front casing is installed and
closed.
1.3.8 Risk of poisoning caused by
insufficient supply of combustion
air
Conditions: Open-flued operation
▶ Ensure that the air supply to the product's
installation room is permanently unobstructed and sufficient in accordance with the
relevant ventilation requirements.
Compartment ventilation
The boilers are very high efficiency appliances. As a consequence the heat loss from
the appliance casing during operation is very
low. Compartment ventilation is required if the
flue used is not concentric and air is supplied
from the room or compartment the boiler is installed in.
1.3.9 Risk of death due to lack of safety
devices
The schematic drawings included in this document do not show all safety devices required for correct installation.
▶ Install the necessary safety devices in the
system.
▶ Observe the applicable national and international laws, standards and guidelines.
1.3.10 Risk of death from electric shock
1.3.6 Risk of death due to explosive and
flammable materials
There is a risk of death from electric shock if
you touch live components.
▶ Do not use or store explosive or flammable
materials (e.g. petrol, paper, paint) in the
installation room of the product.
Before commencing work on the product:
1.3.7 Risk of death due to cabinet-type
casing
Cabinet-type casing can give rise to dangerous situations when used on a product which
is operated with an open flue.
▶ Ensure that the product is supplied with
sufficient combustion air.
▶ Disconnect the product from the power
supply by switching off all power supplies
(electrical partition with a contact opening
of at least 3 mm, e.g. fuse or line protection switch).
▶ Secure against being switched back on
again.
▶ Wait for at least 3 minutes until the capacitors have discharged.
▶ Check that there is no voltage.
1.3.11 Risk of being burned or scalded by
hot components
▶ Only carry out work on these components
once they have cooled down.
0020209593_01 ecoTEC plus Installation and maintenance instructions
5
1 Safety
1.3.12 Risk of death from escaping flue
gas
If you operate the product with an empty condensate trap, flue gas may escape into the
room air.
▶ During repair work, do not apply any leak
detection sprays or liquids to the covering
cap on the filter of the Venturi.
1.3.17 Risk of damage to the flexible gas
pipe
▶ In order to operate the product, ensure that
The corrugated gas pipe may become damthe condensate trap is always full.
aged if weight is placed on it.
1.3.13 Risk of material damage caused by
using an unsuitable tool
▶ Use the correct tool to tighten or loosen
screw connections.
1.3.14 Risk of material damage caused by
frost
▶ Do not install the product in rooms prone
to frost.
1.3.15 Risk of corrosion damage due to
unsuitable combustion and room
air
Sprays, solvents, chlorinated cleaning
agents, paint, adhesives, ammonia compounds, dust or similar substances may lead
to corrosion on the product and in the air/flue
pipe.
▶ Ensure that the supply of combustion air is
always free of fluorine, chlorine, sulphur,
dust, etc.
▶ Ensure that no chemical substances are
stored at the installation site.
▶ Ensure that the combustion air is not
routed through chimneys which have
previously been used with floor-standing
oil-fired boilers, or with other boilers,
which could cause soot to build up in the
chimney.
▶ If you are installing the product in
hairdressing salons, painter's or joiner's
workshops, cleaning businesses or similar
locations, choose a separate installation
room in which a combustion air supply is
ensured that is technically free of chemical
substances.
1.3.16 Risk of material damage caused by
leak detection sprays and liquids
Leak detection sprays and liquids block the
filter of the mass flow sensor on the Venturi,
and thus destroy the mass flow sensor.
6
▶ Do not suspend the compact thermal module on the flexible gas pipe, for example
during maintenance work.
1.4
Related documents
Installation and maintenance of the boiler
must only be performed by a competent person with valid accreditation from the Health
and Safety Executive in accordance with the
"Gas Safety (Installation and Use) Regulations 1998" (hereinafter abbreviated to "competent person" or "heating specialist company"). The existing regulations, rules and
guidelines must be observed when doing so.
Any special requirements of Local Authorities, gas undertakings or insurers must be
complied with. The competent person is also
responsible for inspection, maintenance and
repairs to the boiler, and for checking gas
volume setting and flue gas analysis.
Installers shall carryout a full site risk assessment and put into place all necessary
steps and procedures to comply with Health
and safety at work act and ensure safety of
themselves and others with regard to manual
handling and working at height requirements.
During the appliance installation (and any
subsequent work, such as, the replacement
of major parts ) it will be necessary to employ caution. All installers and operatives involved from unloading the appliance until it is
fully mounted on the wall in its final installed
location must exercise full duty of care for
themselves and others with regard to safety.
When lifting and handling this appliance, operatives should employ assistance. In certain
situations it may be necessary to use mechanical handling aids. Take care to avoid trip
hazards, slippery or wet surfaces.
Employers and installers should refer
to the HSE web site for full advice and
manual handling assessment charts
(MAC) tool.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Safety 1
In addition where no specific instructions are
given then reference shall be made, but not
restricted to, all applicable and relevant British Standards and codes of practice such as
the following:
– Gas Safety (Installation and Use) regulations.
– All current Building Regulations for England, Northern Ireland and Wales, (as
amended). This includes Approved Codes
of Practice and approved documents and
guidance for building regulations. (A to P
and 7)
– The Building Standards, Scotland, and
any requirements determined by the local
authorities within.
– The Health and safety at work act
– COSHH Control of Substances Hazardous
to Health.
– BS 7671 Requirements for electrical installations. IEE Wiring Regulations
– The Electricity at Work Regulations.
– The Water supply (water fittings) regulations 1999.
– Water bylaws 2000 (Scotland)
– BS 5854 Code of practice for flues and flue
structures in buildings.
– BS EN 12828 Design of water-based heating systems.
– BS EN 806 Parts 1 - 5.
– BS 8558 Guide to the design, installation,
testing and maintenance of services supplying water for domestic use within buildings and their curtilages.
– BS 6880 Code of practice for low temperature heating systems with outputs above
45 kW, Part 1, 2, and 3.
– BS 6891 Installation of low pressure gas
pipe work of up to 35mm in domestic
premises.
– BS 4814 Specification for: Expansion
vessels using an internal diaphragm, for
sealed hot water and heating systems.
– BS 7074 Application, selection and installation of expansion vessels and ancillary
equipment for sealed water systems., Part
1 and 2.
– BS 7593 Code of practice for treatment of
water in domestic hot water central heating
systems.
0020209593_01 ecoTEC plus Installation and maintenance instructions
– BS 12831 Heating systems in buildings.
Method for calculating design heat load.
– BS EN 13831 Closed expansion vessels
with built in diaphragm.
– EN 14336 Heating systems in buildings.
Installation and commissioning of water
based heating systems.
– BS 5440 – 1 Installation of flues and ventilation for gas appliances of rated input not
exceeding 70kW*
– BS 5440 – 2 Flueing and ventilation for gas
appliances of rated input not exceeding
70kW*
* 1st 2nd and 3rd family gases.
– BS 5449 Forced circulation hot water systems up to 45kW.
– BS EN 6798 Installation & maintenance of
gas fired hot water boilers of rated input
not exceeding 70kW net.
– BS 5482 - Part 1 Domestic butane and
propane gas burning installations
Institute of Gas Engineers Publications:
– IGE/UP/1B (Edition 2) Tightness testing
and direct purging of small natural gas
installations.
– IGE/UP/ 7 (Edition 2) Gas in timber and
light steel framed buildings.
Additionally for gas boilers systems with outputs greater than 70KW.
– BS 6644 Installation of gas boilers
between 60 kW and 2 MW (2nd and 3rd
family gases)
– BS 5449
– IGE/UP/1 (Edition 2) Strength testing,
tightness testing and direct purging of industrial and commercial gas installations.
– IGE/UP/1A (Edition 2) Strength testing,
tightness testing and direct purging of
small, low pressure industrial and commercial natural gas installations.
– IGE/UP/10 Installation of gas appliances
in industrial and commercial premises.
Part 1 Flued appliances.
– The installation must comply with the current version of the Clean Air Act.
7
1 Safety
1.5
–
–
–
–
8
Related documents
I.S. 813 Domestic Gas Installations
I.S. 820 Non Domestic Gas Installations
Building Control Act 2007
ETCI Regulations for installing electrical
systems
Installation and maintenance instructions ecoTEC plus 0020209593_01
Notes on the documentation 2
2
2.1
▶
2.2
▶
2.3
Notes on the documentation
Observing other applicable documents
You must observe all the operating and installation instructions included with the system components.
Storing documents
Pass these instructions and all other applicable documents on to the system operator.
3
Product description
3.1
Design of the product
The product comprises:
–
–
A 15 litre shift-load cylinder
A modified boiler with integrated hot water generation
3.1.1
Functional elements of the shift-load
cylinder
Validity of the instructions
1
These instructions apply only to:
Product article number
938 (VUI GB 386/5‑5 A)
ecoTEC plus
2.4
Article number
Gas Council
Number
0010018357
47-044-61
Benchmark
Vaillant is a licensed member of the Benchmark Scheme
which aims to improve the standards of installation and commissioning of domestic heating and hot water systems in the
UK and to encourage regular servicing to optimise safety, efficiency and performance.
Benchmark is managed and promoted by the Heating and
Hotwater Industry Council.
2
3
4
For more information visit www.centralheating.co.uk
2.5
5
Local regulations
Benchmark places responsibilities on both manufacturers
and installers. The purpose is to ensure that customers are
provided with the correct equipment for their needs, that it is
installed, commissioned and serviced in accordance with the
manufacturer’s instructions by a competent person approved
at the time by the Health and Safety Executive and that it
meets the requirements of the appropriate Building Regulations. The Benchmark Checklist can be used to demonstrate compliance with Building Regulations and should be
provided to the customer for future reference.
1
Expansion vessel
4
Hot water NTC sensor
2
Impeller sensor
5
Expansion relief valve
3
Cylinder charging pump
Installers are required to carry out installation, commissioning and servicing work in accordance with the Benchmark
Code of Practice which is available from the Heating and
Hotwater Industry Council who manage and promote the
Scheme.
0020209593_01 ecoTEC plus Installation and maintenance instructions
9
3 Product description
3.1.2
Functional elements, product with hot
water generation
6
5
7
8
4
3
ecoTEC plus
Product designation
2H, G20 – 20 mbar
(2.0 kPa)
Gas group and gas connection pressure
as set at the factory
ww/yyyy
Date of manufacture: Week/year
Cat.
Permissible gas categories
Types
Approved gas-fired units
10
PMS
Permissible total overpressure in heating
mode
11
PMW
Permissible total overpressure during hot
water generation
Tmax.
Max. flow temperature
ED 92/42
Current efficiency directive fulfilled with
4* rating
V Hz
Mains voltage and mains frequency
W
Max. electrical power consumption
IP
Level of protection
13
1
Meaning
9
12
2
Information on the
identification plate
14
15
Heating mode
16
Hot water generation
20
19
Gas valve
10
Ignition electrode
2
Water pressure sensor
11
Fan
3
Venturi with mass flow
sensor
Heat exchanger
12
Automatic air vent
13
Pressure gauge
14
Internal pump
15
Bypass valve
16
Expansion relief valve
17
Electronics box
18
Diverter valve
19
Impeller sensor (hot
water)
Secondary heat exchanger
7
Connection for the flue
pipe
Flue gas measuring
stub pipe
Expansion vessel
8
Air intake pipe
9
Compact thermal module
6
3.2
20
Heat input range
Nominal hot water draw-off rate
Proper disposal of the product
Bar code with serial number,
7th to 16th digit = product article number
Note
Make absolutely sure that the product is compatible with the gas group at the installation site.
3.3
Information on the
identification plate
Serial number
The serial number can be found on a plastic label behind the
front flap and on the identification plate.
Note
The serial number can also be shown on the
display of the product (→ Operating instructions).
Information on the identification plate
The identification plate is mounted on the underside of the
product in the factory.
3.4
CE label
Meaning
→ "CE label" section
Read the instructions.
VUI…
Vaillant gas-fired wall-hung boiler for
heating and hot water generation with
shift-load cylinder
..6/5-5
Calorific value power/product generation
equipment
10
Q
17
1
5
Nominal heat output range
D
18
4
P
The CE label shows that the products comply with the basic
requirements of the applicable directives as stated on the
identification plate.
The declaration of conformity can be viewed at the manufacturer's site.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Installation 4
3.5
Energy Saving Trust Endorsed Products
Only the most energy efficient products can carry the
‘Energy Saving Trust Endorsed Product’ brandmark making
it easy for consumers to choose products that have met strict
energy performance criteria.
Available for: Boilers, Heating controls and chemical inhibitors, the Energy Saving Trust endorsed product brandmark
gives consumers confidence that a product will cost less to
run, help lower energy bills and reduce carbon emissions.
About the Energy Saving Trust
Energy Saving Trust is an independent and impartial organisation that provides trusted energy saving advice to empower millions of people to lead affordable, low energy lifestyles. For more information visit energysavingtrust.org.uk
4
Installation
4.1
1.
2.
Unpacking the product
Remove the product from its box.
Remove the protective film from all parts of the product.
4.2
▶
Checking the scope of delivery
Check that the scope of delivery is complete and intact.
Number
Description
1
Lower cover of heat generator
1
Installation template
1
Condensate drain hose
1
Enclosed documentation
4.3
Transporting the product
4.3.1
General
▶
▶
▶
▶
▶
Hold the load as close as possible to your body. Do not
twist your body – instead, reposition your feet.
If the unit is being lifted by two persons, ensure your
movements are coordinated during lifting.
Avoid bending your upper body – do not lean forwards or
to the side.
Wear appropriate cut-resistant and non-slip gloves to
protect yourself against sharp edges and maintain a safe
and secure grip.
If required, get somebody to assist you in this.
4.3.2
▶
▶
▶
▶
▶
It is recommended that two people lift the unit together.
Lift the box using the straps provided.
Use safe lifting techniques – keep your back straight and
bend your legs at the knee.
Hold the load as close as possible to your body.
If the unit is being lifted by two persons, ensure your
movements are coordinated during lifting.
If required, get somebody to assist you in this.
Scope of delivery
▶
Number
Description
4.3.3
1
Heat generator
1
Shift-load cylinder
1
Lower cover of shift-load cylinder
1
Kit for wall installation:
1
- Product retainer
1
- Bag with small parts
1
Shift-load cylinder installation kit containing the following:
2
- Connection pipe (heating flow and return)
1
- Shift-load cylinder-in connection pipe
1
- Shift-load cylinder-out connection pipe
1
- Drain hose for the expansion relief valve on the shiftload cylinder
1
- Bag with small parts
1
Heat generator installation kit containing the following:
1
- Connector for the expansion relief valve on the boiler
1
- Connector 15 mm (gas)
4.2.1
1
- Gas compression joint, 15 mm
4
- Service valve
1
- Hot water connector
1
- 22 mm connection piece (heating flow and return
connection)
2
- Bag with small parts
0020209593_01 ecoTEC plus Installation and maintenance instructions
▶
▶
Unloading the box from the delivery van
Transporting the box from the delivery
point to the installation site – ground floor
It is recommended that two people lift the unit together.
Use safe lifting techniques – keep your back straight and
bend your legs at the knee.
11
4 Installation
4.4
Dimensions
3
4
5
4
6
12
7
5
6
7
8
180
323
624
9
10
11
Hot water connection
(15 × 1.5 diameter)
Gas connection
(15 × 1.5 diameter)
Cold water connection
(15 × 1.5 diameter)
Heating return (22 × 1.5
diameter)
Flue pipe connection
10
Condensate siphon
11
Shift-load cylinder expansion relief valve
drain line connection,
15 mm diameter
Heat generator expansion relief valve discharge pipe connection,
15 mm diameter
12
Condensate discharge
connection, 19 mm
diameter
Consult the installation template that is supplied to find the
dimension A.
4.5
Minimum clearances
9
A
440
1
C
D
A
C
624
720
B
2
Minimum clearance
20
3
4
5
6
7
35
100
100
2
Product holder
12
B
180 mm; optimum approx. 250 mm
C
5 mm; optimum approx. 50 mm
D
500 mm in front of the heat generator to enable
easy access for maintenance work (may be
provided by an opening door).
4.6
▶
3
Clearance from combustible components
It is not necessary to maintain a clearance between the
product and components made of combustible materials.
4.7
323
Wall duct for flue pipe
165 mm: Air/flue pipe, 60/100 mm diameter
275 mm: Air/flue pipe, 80/125 mm diameter
35
8
1
A
Using the installation template
Use the installation template to ascertain the locations at
which you need to drill holes and make breakthroughs.
Heating flow (22 × 1.5
diameter)
Installation and maintenance instructions ecoTEC plus 0020209593_01
Installation 4
4.8
1.
Wall-mounting the product
4.9
Removing the front casing
Check whether the wall has sufficient load-bearing capacity to bear the operational weight of the product.
Check if the supplied fixing material may be used for
the wall.
2.
Conditions: The load-bearing capacity of the wall is sufficient, The fixing
material may be used for the wall
▶
Wall-mount the product as described.
1
2
3
▶
▶
▶
Install the reinforced product bracket (1) on the wall.
Hang the shift-load cylinder on the product bracket from
above using the hanging bracket.
Remove the front casing as shown in the illustration.
4.10
Removing the side section
2x
1
2
▶
Hang the heat generator (2) on the product bracket on
the shift-load cylinder (1) from above using the hanging
bracket.
Conditions: The fixing material may not be used for the wall
▶
Wall-mount the product as described using the permitted
fixing material provided on-site.
Caution.
Risk of material damage caused by mechanical deformation.
Removing both side sections may cause
mechanical distortion in the product, which
may cause damage to the piping, for example, and potentially result in leaks.
0020209593_01 ecoTEC plus Installation and maintenance instructions
13
5 Installation
▶
▶
5
Always remove only one side section –
never both side sections at the same time.
Remove the side section as shown in the illustration.
Installation
Danger!
Risk of scalding and/or risk of material
damage due to incorrect installation leading to escaping water.
Stresses in supply lines can cause leaks.
▶
Install the supply lines without tension.
Caution.
Risk of material damage due to the gas
leak-tightness test.
At a test pressure of >11 kPa (110 mbar), gas
leak-tightness tests may cause damage to
the gas valve.
▶
▶
▶
If, during gas leak-tightness tests, you
also place the gas lines and the gas valve
in the product under pressure, use a max.
test pressure of 11 kPa (110 mbar).
If you cannot limit the test pressure to
11 kPa (110 mbar), close any gas isolator
cocks that are installed upstream from the
product before you carry out the gas leaktightness test.
If, during gas leak-tightness tests, you
have closed the gas isolator cock that is
installed upstream of the product, relieve
the gas line pressure before you open this
gas isolator cock.
Caution.
Risk of material damage due to corrosion.
If non-diffusion-tight plastic pipes are used
in the heating installation, this may cause
air to enter the heating water and corrosion
of the heat generation circuit and the heat
generator.
▶
If using non-diffusion-tight plastic pipes
in the heating installation, partition the
system by installing an external heat exchanger between the heat generator and
the heating installation.
5.1
Installation requirements
5.1.1
Information on liquid gas operation
In the as-delivered condition, the product is preset for operation with the gas group indicated on the identification plate.
If you have a product that has been preset for operation with
natural gas, you must convert it to run on liquid gas. You will
need a conversion kit for this. The conversion procedure is
described in the manual supplied with the conversion kit.
5.1.2
Purging the liquid gas tank
If the liquid gas tank is not purged properly, this may result in
ignition problems.
▶
▶
Ensure that the liquid gas tank has been purged properly
before installing the product.
If required, contact the filler or the liquid gas supplier.
5.1.3
Using the correct type of liquid gas
Using the incorrect type of liquid gas may cause fault shutdowns in the product. Ignition and combustion noise may
occur in the product.
▶
Only use the gases listed on the identification plate.
5.1.4
1.
2.
3.
Required preliminary work
Install a stop cock in the gas line.
Make sure that the existing gas meter is capable of
passing the rate of gas supply required.
Check that the volumetric capacity of the expansion
vessel is sufficient for the system volume.
Conditions: The volume of the installed expansion vessel is insufficient
▶
Install an additional expansion vessel, connected as
close to the product as possible, in the heating return.
Conditions: External expansion vessel installed
▶
4.
5.
Install a non-return valve in the product outlet (heating
flow) or decommission the internal expansion vessel
in order to prevent the warm start function from being
increasingly activated due to backflow.
Install a tundish with siphon for the condensate discharge and the exhaust pipe on the expansion relief
valve. Lay as short a drain line as possible, at a downward gradient away from the tundish.
Insulate bare pipes exposed to environmental influences to protect them from frost using suitable insulating material.
Caution.
Risk of material damage due to heat transfer during soldering.
▶
14
Do not solder the connection pieces if
the connection pieces are screwed to the
service valves.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Installation 5
5.2
Installing the gas connection
5.4
Installing pipe connections between the
shift-load cylinder and the heat generator
1
2
3
4
1
1.
2.
3.
4.
5.
5.3
1.
2.
Install the gas line in accordance with the recognised
rules of technology.
Connect the product to the gas line as shown in accordance with the recognised rules of good engineering
practice. Use the extended gas pipe (1) from the enclosure to do this.
Remove the residues from the gas line by blowing
through the gas line beforehand.
Purge the gas line before start-up.
Check the gas line for leak-tightness.
Installing the hot and cold water connection
Make the water connections as shown in accordance
with the relevant standards.
Ensure correct water pressure and flow requirements
and that any expansion can be accommodated with the
cold supply pipe work.
0020209593_01 ecoTEC plus Installation and maintenance instructions
1.
2.
Install pipe connections between the shift-load cylinder
and the heat generator.
From the shift-load cylinder installation kit, install first
the pipes (1) and (2), and then the pipes (3) and (4), to
a professional standard.
◁
5.5
▶
These join the shift-load cylinder and the heat generator with integrated hot water generation to create
the product VUI.
Connecting the heating flow and heating
return
Make the heating connections as shown in accordance
with the relevant standards.
15
5 Installation
5.6
Connecting the condensate drain pipework
Danger!
Risk of death from escaping flue gases!
The condensate drain pipework for the siphon must not be connected tightly to wastewater piping because, otherwise, the internal
condensate trap may be drained fully and flue
gas may escape.
▶
Do not connect the condensate drain
pipework tightly to the waste-water piping.
▶
▶
5.7
when crossing cavities that the fall is maintained and the
pipe sleeved.
Ensure that the condensate drain pipework terminates in
a suitable location. Further information can be obtained
from BS 6798 Specification for installation of gas–fired
boilers of rated input not exceeding 70 kW net.
Leave an installation space of at least 180 mm beneath
the condensate trap.
Installing the discharge pipe on the
expansion relief valve
1.
Install the discharge pipe for the expansion relief valve
so that it does not interfere with the removal and fitting
of the lower section of the condensate trap.
2.
3.
4.
Install the discharge pipe as shown (do not shorten).
Make sure that the end of the pipe is visible.
Ensure that discharged water or steam cannot cause
injury to persons or damage to electronic components.
Ensure the discharge pipe work is installed, routed and
terminated correctly to minimise the risk of freezing up.
min.
180
1
2
3
Internal
stackpipe
Internal
discharge system
Gulley
Soakaway
The product is equipped with a condensate trap (2). (The
filling height is 145 mm). The condensate trap collects the
condensate that has formed in a vessel with a capacity of
approximately 200 ml, and intermittently releases the contents into the discharge pipe. This minimises the risk of the
discharge pipe freezing.
▶
▶
▶
16
Connect the condensate discharge (1) to condensate
drain pipework (3) which has a minimum internal diameter of 19 mm (22 mm outside diameter for all external
pipes) and is made from an acid-resistant material (e.g.
plastic overflow pipe).
– The condensate discharge pipework must have
a continuous fall (45 mm per metre) and should
whenever possible terminate at a suitable discharge
point within the heated envelope of the building
that will remain frost free under long periods of low
external temperatures.
During installation remove all burs from inside of cut pipe
work and avoid excessive adhesive which may trap small
pockets of water close to the pipe wall which can freeze
and build into a larger ice plug.
As with other pipe work insulate the condensate discharge pipe to minimise any risk of freezing and beware
5.
5.8
Connecting the flexible hose to the
expansion relief valve on the shift-load
cylinder
Danger!
Risk of scalding!
Heating water that leaks from the drain of
the expansion relief valve may cause severe
burns.
▶
▶
Install the expansion relief valve drain to a
professional standard.
Use the flexible hose that is included in
the scope of delivery.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Installation 5
3.
3.
Alternatives 1 / 2
▶
If required, install the connection piece for the
air/flue pipe, 80/125 mm diameter. (→ Page 17)
Alternatives 2 / 2
▶
If required, install the connection piece with
offset for the air/flue pipe, 60/100 mm diameter.
(→ Page 17)
5.9.2.1 Removing the connection piece for the
air/flue pipe
3.
1.
2.
2
1
1.
2.
3.
Connect the flexible hose (1) to the expansion relief
valve (2).
Route the end of the flexible hose with a downward
gradient via an open connection to a tundish.
Make sure that the line end is visible.
5.9
Flue gas installation
5.9.1
Installing and connecting the flue pipe
1.
2.
You can find out which flue pipes may be used by consulting the enclosed flue pipe installation manual.
Observe the information on positioning the opening
for the flue pipe. This information can be found in the
appendix.
Conditions: Installation in damp rooms
▶
You must connect the product to a room-sealed air/flue
gas installation. The combustion air must not be taken
from the installation site.
Caution.
Risk of poisoning due to escaping flue
gas.
1.
2.
3.
5.9.2.2 Installing the connection piece for the
air/flue pipe, 80/125 mm diameter
1.
2.
3.
3.
1.
1.
2.
Remove the connection piece for the air/flue pipe.
(→ Page 17)
1
Instead of grease, use only water or commercially available soft soap to aid installation.
65 mm
Install the flue pipe using the installation manual.
5.9.2
Remove the connection piece for the air/flue pipe.
(→ Page 17)
Insert the alternative connection piece. In doing so, pay
attention to the latching lugs.
Turn the connection piece clockwise until it clicks into
position.
5.9.2.3 Installing the connection piece with offset
for the air/flue pipe, 60/100 mm diameter
Mineral-oil-based greases can damage the
seals.
▶
Insert a screwdriver into the slot between the measuring
stub pipes.
Press the screwdriver carefully down (1.).
Turn the connection piece anticlockwise (2.) as far as it
will go and then remove it by pulling it upwards (3.).
Replacing the connection piece for the
air/flue pipe as required
Replace the connection piece for the air/flue pipe as
required. The product-specific standard equipment is
listed under Technical data.
Remove the connection piece for the air/flue pipe.
(→ Page 17)
0020209593_01 ecoTEC plus Installation and maintenance instructions
2.
3.
Insert the alternative connection piece with offset towards the front.
Use two screws (1) to secure the connection piece to
the product.
17
5 Installation
5.10
Electrical installation
The electrical installation must only be carried out by a qualified electrician.
Danger!
Risk of death from electric shock!
Mains connection terminals L and N remain
live even if the on/off switch is turned off:
▶
▶
Switch off the power supply.
Secure the power supply against being
switched on again.
5.10.1 Opening the electronics box
5.
Ensure the inner conductor insulation is not damaged
when stripping the outer sheathing.
6. Only strip inner conductors just enough to establish
good, sound connections.
7. To avoid short circuits resulting from loose individual
wires, fit conductor end sleeves on the stripped ends of
the conductors.
8. Screw the respective plug to the connection cable.
9. Check whether all conductors are sitting mechanically
securely in the terminals of the plug. Remedy this if
necessary.
10. Plug the plug into the associated PCB slot; see the
connection diagram in the appendix.
5.10.3 Connecting the shift-load cylinder to the
heat generator electronics
1.
2.
Open the electronics box. (→ Page 18)
Carry out the wiring. (→ Page 18)
1
2
▶
Open the electronics box as shown in the illustration.
3
5.10.2 Carrying out the wiring
Caution.
Risk of material damage caused by incorrect installation.
Caution.
Risk of material damage caused by incorrect cable routing
Mains voltage at incorrect terminals and plug
terminals may destroy the electronics.
▶
▶
Cables may become damaged if they come
into contact with hot parts of the product.
Do not connect any mains voltage to the
eBUS terminals (+/-).
Only connect the mains connection cable
to the terminals marked for the purpose.
▶
3.
1.
2.
3.
Route the connection cables of the components to be
connected through the cable duct provided on the underside of the product on the left.
Use strain reliefs.
Shorten the connection cables as necessary.
4.
5.
Lay cables in such a way that they do not
touch any hot parts of the product.
Route the shift-load cylinder's cable harness (2) with the
grommets (3) through the attached cable ducts on the
shift-load cylinder and on the heat generator.
On the boiler, use the cable duct (1).
Secure the grommets on the cable ducts using the enclosed spring clips.
30 mm max.
4.
18
To prevent short circuits if a strand accidentally comes
loose, only strip the outer sheathing of flexible lines to a
maximum of 30 mm.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Installation 5
1
5.10.5 Installing the product in a moist
environment
2
Danger!
Risk of death from electric shock!
X12
X31
If you install the product in a room with high
levels of moisture, e.g. a bathroom, observe
the nationally recognised technical standards
for electrical installations. If you use the factory-installed connection cable, if installed,
with an earthed plug, there is a risk of death
from electric shock.
▶
6.
Guide the pump cable (2) with the plug X12 along the
outside of the electronics box.
7. Plug the pump cable's plug X12 into the slot X12 (righthand side of the PCB).
8. Guide the sensor cable (1) with the plug X31 to the
PCB.
9. Plug the sensor cable's plug X31 into the slot X31 (lefthand side of the PCB).
10. Secure the cable over the cable terminals in the electronics box.
5.10.4 Establishing the power supply
Caution.
Risk of material damage due to high connected voltage.
At mains voltages greater than 253 V, electronic components may be damaged.
▶
1.
2.
3.
4.
5.
6.
7.
8.
9.
Make sure that the rated voltage of the
mains is 230 V.
Make sure that the nominal mains voltage is 230 V.
Provide one common electricity supply for the boiler
and for the corresponding controller:
– Power supply: Single-phase, 230 V, 50 Hz
– Fuse protection: ≤ 3 A
Open the electronics box. (→ Page 18)
Connect the product using a fixed connection and a
partition with a contact opening of at least 3 mm (e.g.
fuses or power switches).
Route a three-core power supply cable that complies
with the relevant standards through the cable duct and
into the product.
– Power supply cable: Flexible line
Carry out the wiring. (→ Page 18)
Remove the supplied plug from the bracket in the electronics box and screw the plug onto the power supply
cable.
Close the electronics box.
Make sure that access to the power supply is always
available and is not covered or blocked.
0020209593_01 ecoTEC plus Installation and maintenance instructions
▶
▶
1.
2.
3.
4.
5.
6.
7.
Never use the factory-installed connection
cable with earthed plug when installing the
product in a moist environment.
Connect the product using a fixed connection and a partition with a contact opening of at least 3 mm (e.g. fuses or power
switches).
Use a flexible line for the mains connection line, which is routed through the cable
duct into the product.
Open the electronics box. (→ Page 18)
Detach the plug from the PCB slot for the power supply
(X1).
Unscrew the plug of the factory-installed power supply
cable, if installed.
Instead of the factory-installed power supply cable, if
installed, use a suitable three-core power supply cable
which complies with the relevant standards.
Carry out the wiring. (→ Page 18)
Close the electronics box.
Observe the flue-gas connection that is required on a
room-sealed air/flue gas installation. (→ Page 17)
5.10.6 Connecting controllers to the electronic
system
1.
2.
3.
4.
Install the controller if necessary.
Open the electronics box. (→ Page 18)
Carry out the wiring. (→ Page 18)
Observe the connection diagram in the appendix.
Conditions: Connecting a weather compensator or a room temperature
controller via eBUS
▶
▶
Connect the controller to the eBUS connection.
Bridge the 24 V = RT connection (X100 or X106), if there
is not already a bridge.
Conditions: Connecting a low-voltage controller (24 V)
▶
Remove the bridge and connect the controller to the
24 V = RT connection (X100 or X106).
Conditions: Connecting 230 volt controller
▶
Connect the switched live supply with the terminal
marked RT at X1 (beside the LNPE connections) then
remove the link at X100 (do NOT connect 230 volt to
any other terminal than the RT connection).
19
6 Operation
Conditions: Connecting a limit thermostat for underfloor heating
6.2
▶
1.
5.
6.
Remove the bridge and connect the limit thermostat to
the Burner off connection.
Close the electronics box.
For multi-circuit controllers, change D.018 from Eco (intermittently operating pump) to Comfort (continuously
operating pump). (→ Page 28)
2.
3.
Calling up the installer level
Only call up the installer level if you are a competent
person.
Navigate to Menu → Installer level and confirm by
pressing
.
Set the value 17 (code) and confirm by pressing
.
6.3
Live Monitor (status codes)
5.10.7 Connecting additional components
Menu → Live Monitor
You can actuate an additional component with the aid of the
auxiliary relay that is installed, and you can actuate two other
components with the multi-functional module.
Status codes in the display provide information on the product's current operating status.
5.10.7.1 Using the auxiliary relay
1.
2.
3.
Connect an additional component directly to the integrated auxiliary relay using the grey plug on the PCB.
Carry out the wiring.
To start up the connected component, select the component in diagnostics code D.026. (→ Page 28)
Status codes – Overview (→ Page 47)
6.4
Setting the hot water temperature
Conditions: Water hardness: > 3.57 mol/m³
Danger!
Risk of death from Legionella.
Legionella multiply at temperatures below
60 °C.
▶ Ensure that the operator is familiar with
all of the Anti-legionella measures in order to comply with the applicable regulations regarding legionella prevention.
5.10.7.2 Using the VR 40 ("2 in 7" multi-functional
module)
1.
Install the components in accordance with the respective instructions.
Conditions: Components connected to relay 1
▶
Activate D.027. (→ Page 28)
▶
Set the hot water temperature to a maximum of 50 °C.
Conditions: Components connected to relay 2
▶
Activate D.028. (→ Page 28)
5.10.8 Actuating the circulation pump according
to requirements
1.
2.
3.
6
6.1
Carry out the wiring.
Connect the supply line for the external button using
terminals 1 (0) and 6 (functional drawing) on the X41
edge connector, which is supplied with the controller.
Plug the edge connector into the PCB slot X41.
Operation
Operating concept
The operating concept and the read-off and setting facilities
of the operator level are described in the operating instructions.
An overview of the reading and setting options for the installer level is included in the table in the appendix.
Installer level – Overview (→ Page 41)
7
Start-up
7.1
Carrying out the initial start-up
Initial start-up must be carried out by a customer service
technician or an authorised competent person using the
commissioning checklist. The commissioning checklist in the
appendix (→ Page 55) of the installation instructions must be
filled in and stored carefully along with the unit's documentation.
▶
▶
Carry out the start-up procedure using the commissioning
checklist in the appendix.
Fill in and sign the commissioning checklist.
7.2
▶
Switching the product on and off
Press the on/off button on the product.
◁
7.3
The basic display appears on the display.
Running the installation assistants
The installation assistant is displayed whenever the product
is switched on until it has been successfully completed.
It provides direct access to the most important check
programmes and configuration settings for starting up the
product.
To recheck and reset the most important system parameters,
call up the Appliance config..
Menu → Installer level Appliance config.
The settings options for more complex systems can be found
in the Diagnostics menu.
20
Installation and maintenance instructions ecoTEC plus 0020209593_01
Start-up 7
Menu → Installer level Diagnostics menu
7.3.6
▶
1.
Press
◁
to confirm installation assistant start-up.
All heating and hot water requests are blocked whilst
the installation assistant is active.
2.
Auxiliary relay and multi-functional module
If you have connected additional components to the
product, assign these components to the individual relays.
In each case, confirm by pressing
.
Note
If you do not confirm the launch of the installation assistant within 10 seconds of switching
the system on, the basic display reappears.
▶
To access the next point, confirm by pressing
case.
7.3.1
▶
▶
in each
Language
Set the required language.
To confirm the set language and to avoid unintentionally
changing it, press
to confirm this twice.
If you have unintentionally set a language that you do not
understand, proceed as follows to change it:
▶
▶
▶
▶
▶
Press and hold
and
at the same time.
Also briefly press
.
Press and hold
and
until the display shows the
language setting option.
Select the required language.
Press
twice to confirm this change.
7.3.2
Filling mode
Filling mode (check programme P.06) is activated automatically in the installation assistant for as long as the filling mode
appears on the display.
7.3.3
1.
2.
Unlike in the Check programs menu, to purge the system, start up the check programme P.00 by pressing
or
.
If you need to change the circuit that is being purged,
press
.
7.3.4
1.
2.
Purging
Target feed temperature, hot water
temperature, Comfort mode
To set the target flow temperature, hot water temperature and Comfort mode, use
and
.
Press
to confirm this setting.
7.3.5
Heating partial load
The heating partial load of the product is set to Auto at the
factory. The product independently determines the optimum
heating output depending on the current heat demand of
the system. You can retroactively change the setting in the
Diagnostics menu under D.000.
Note
This setting can be retroactively changed in
the Diagnostics menu using D.026, D.027
and D.028.
7.3.7
▶
If required, store your telephone number in the Appliance config. (max. 16 digits/no blank spaces). The operator can view the telephone number.
7.3.8
▶
Ending the installation assistant
Once you have run through the installation assistant successfully, confirm by pressing
.
◁
7.4
Contact data
The installation assistant will close and will not launch
again when the product is next switched on.
Restarting the installation assistants
Menu → Installer level → Start inst. assistant
You can restart the installation assistant at any time by calling it up in the menu.
7.5
Test programmes
Menu → Installer level Test programs
As well as the installation assistants, you can also call up
the following test programmes for start-up, service and
troubleshooting.
–
–
–
7.6
Check programs
Function menu
Electronics self-test
Performing a gas family check
Danger!
Risk of poisoning!
Inadequate combustion quality (CO), indicated by F.92/93, leads to an increased risk of
poisoning.
▶
Make sure that the fault is completely
eliminated before starting up the product
for continuous operation.
Menu → Installer level → Test programs → Gas family
check
The gas family check checks the product setting with regard
to combustion quality.
0020209593_01 ecoTEC plus Installation and maintenance instructions
21
7 Start-up
Note
If additional condensing units are connected to the
same flue gas pipe in the heating installation, ensure that none of these condensing units are in
operation or start operating throughout the entire
test programme, so that the test result is not distorted.
▶
Display
Meaning
P.00
Purging check programme:
The internal pump is cyclically actuated.
The heating circuit and the hot water circuit are
purged via the automatic air vent (the cap of the
automatic air vent must be released).
1x
Perform the gas family check as part of routine product
maintenance work, after replacing components, carrying
out work on the gas route and following gas conversion.
Result
Meaning
Measure
F.92
See the table of
fault codes in the
appendix
See the table of fault
codes in the appendix
"Successful"
Combustion
quality is good.
Unit configuration matches
the specified gas
group.
None
"Warning"
Combustion
quality inadequate.
CO₂ content is
incorrect.
Start check programme
P.01 and adjust the
CO₂ content with the
adjusting screw in the
Venturi.
If the correct CO₂ content cannot be set:
Check that the gas restrictor is correct (yellow:
G20 natural gas, blue:
G25 natural gas, grey:
Liquid gas) and undamaged.
Repeat the gas family
check.
F.93
See the table of
fault codes in the
appendix
Menu → Installer level → Test programs → Check programs
): Restart heating circuit purging
Maximum load check programme:
After successful ignition, the product is operated at
maximum heat input.
P.02
Minimum load check programme:
After successful ignition, the product is operated at
minimum heat input.
P.06
Filling mode check programme:
The diverter valve is moved to the mid-position. The
burner and pump are switched off (to fill or drain the
product).
7.8
Checking and treating the heating
water/filling and supplementary water
Caution.
Risk of material damage due to poor-quality heating water
▶
▶
Ensure that the heating water is of sufficient quality.
Before filling or topping up the system, check the quality
of the heating water.
Checking the quality of the heating water
▶
▶
▶
▶
▶
▶
▶
22
): Start hot water circuit purging
(
P.01
See the table of fault
codes in the appendix
Using check programmes
(
3x
1x
(Cancel): End purge programme
Note
The purge programme runs for 7.5 min per circuit
and then terminates.
Purging the heating circuit:
Diverter valve in heating position, actuation of internal pump for 9 cycles: 30 sec. on, 20 sec. off.
Display: Active heating circuit.
Purging the hot water circuit:
After the above-mentioned cycles have run or the
right-hand selection button has been pressed again:
Diverter valve in the hot water position, actuation
of the internal pump as above. Display: Active hot
water circuit.
Note
It is not possible to perform CO₂ measurements during the gas family check.
7.7
: Start heating circuit purging
2x
Remove a little water from the heating circuit.
Check the appearance of the heating water.
If you ascertain that it contains sedimentary materials,
you must desludge the system.
Use a magnetic rod to check whether it contains magnetite (iron oxide).
If you ascertain that it contains magnetite, clean the system and apply suitable corrosion-protection measures, or
fit a magnet filter.
Check the pH value of the removed water at 25 °C.
If the value is below 8.2 or above 10.0, clean the system
and treat the heating water.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Start-up 7
▶
▶
Ensure that oxygen cannot get into the heating water.
Ensure that oxygen cannot get into the heating water.
(→ Page 27)
Checking the filling and supplementary water
▶
Before filling the system, measure the hardness of the
filling and supplementary water.
Treating the filling and supplementary water
▶
Observe all applicable national regulations and technical
standards when treating the filling and supplementary
water.
Provided the national regulations and technical standards
do not stipulate more stringent requirements, the following
applies:
Additives intended to remain permanently in the
system
–
–
–
–
Additives for frost protection intended to remain
permanently in the system
–
–
Fernox Antifreeze Alphi 11
Sentinel X 500
▶
If you have used the above-mentioned additives, inform
the operator about the measures required.
Inform the operator about the measures required for frost
protection.
▶
You must treat the heating water in the following cases:
–
If the entire filling and supplementary water quantity during the operating life of the system exceeds three times
the nominal volume of the heating installation, or
If the guideline values listed in the following table are not
met, or
If the pH value of the heating water is less than 8.2 or
more than 10.0.
–
–
1)
Total
heating
output
Water hardness at specific system volume
> 20 l/kW
≤ 50 l/kW
≤ 20 l/kW
mol/
m³
ppm
CaCO₃
mol/
m³
> 50 l/kW
ppm
CaCO₃
mol/
m³
Fernox F1
Fernox F2
Sentinel X 100
Sentinel X 200
7.9
Preventing low water pressure
To ensure that the heating installation operates smoothly,
the indicator on the pressure gauge must point to the upper
half of the grey area or to the middle of the bar graph display
in the display (marked by the dashed limit values) when the
heating installation is cold. This corresponds to a filling pressure of between 0.1 MPa and 0.2 MPa (1.0 bar and 2.0 bar).
If the heating installation extends over several storeys,
higher filling pressures may be required to avoid air entering
the heating installation.
If the filling pressure falls below 0.08 MPa (0.8 bar), the
product indicates low pressure by displaying a flashing
pressure value. If the filling pressure falls below 0.05 MPa
(0.5 bar), the product switches off. The display shows F.22.
kW
ppm
CaCO₃
< 50
< 300
<3
200
2
2
0.02
> 50
to ≤ 200
200
2
150
1.5
2
0.02
▶
> 200
to ≤ 600
150
1.5
2
0.02
2
0.02
The pressure value flashes in the display until a pressure of
0.11 MPa (1.1 bar) or higher has been reached.
> 600
2
0.02
2
0.02
2
0.02
1) Nominal capacity in litres/heating output; in the case of multiboiler systems, the smallest single heating output is to be used.
7.10
▶
Do not use any unsuitable frost and corrosion protection agents, biocides or sealants.
1.
2.
3.
No incompatibility with our products has been detected to
date with proper use of the following additives.
▶
When using additives, follow the manufacturer's instructions without exception.
We accept no liability for the compatibility of any additive or
its effectiveness in the rest of the heating system.
4.
5.
6.
Additives for cleaning measures (subsequent
flushing required)
7.
–
–
–
8.
Fernox F3
Sentinel X 300
Sentinel X 400
0020209593_01 ecoTEC plus Installation and maintenance instructions
Flushing the heating installation for the first
time ("cold")
Note
The complete heating system must be flushed
at least twice: Once with cold water and once
with hot water in accordance with the following
instructions.
Caution.
Risk of material damage if the heating
water is treated with unsuitable additives.
Unsuitable additives may cause changes in
the components, noises in heating mode and
possibly subsequent damage.
Top up the heating water to start the product up again.
Check whether all thermostatic radiator valves and both
service valves on the product are open.
Connect a hose to the drain valve that is located at the
lowest position in the heating system.
Open the radiator valves and the drain valves so that
the water can drain quickly. Start at the next point in the
system and open the purging valves on the radiators so
that the contaminated water can completely drain.
Close the drain cocks.
Refill the heating system with water.
Check that the expansion relief valve of the heating
system is functioning correctly by turning the handle
on the valve.
Check the pressure in the heating system and top up
with water if necessary.
Close the filling valve and the cold water valve.
23
7 Start-up
7.11
Filling the heating installation
1
14. Fill with water until the required filling pressure is
reached.
15. After filling, close both stop valves and disconnect the
filling device by removing the double non-return valve
from the cold water stop valve.
Note
Both stop valves must be closed while the
heating system is operating and the filling
line must be removed from the double nonreturn valve again.
7.12
1.
Flush the heating installation through.
2.
Undo the cap of the automatic air vent (1) by one to two
rotations and leave it open, as the product purges itself
via the automatic air vent even in continuous mode.
Select the check programme P.06.
3.
◁
4.
The diverter valve moves to the mid-position, the
pumps do not run and the product does not switch
to heating mode.
1.
◁
2.
7.13
3
1
6.
7.
8.
9.
10.
11.
12.
13.
24
1.
2.
The product does not start up, the internal pump
operates intermittently and purges either the heating
circuit or the hot water circuit.
The display shows the filling pressure of the heating
installation.
Make sure that the filling pressure of the heating installation does not fall below the minimum filling pressure.
– ≥ 0.08 MPa ( ≥ 0.80 bar)
◁
3.
4
Select the check programme P.00.
◁
Observe the information on treating heating water.
(→ Page 22)
Check all connections and the entire system for leaks.
5.
Purging the heating installation
At the end of the filling procedure, the filling pressure of the heating installation should be at least
0.02 MPa (0.2 bar) above the counter-pressure
of the expansion vessel ("Exp") (PInstallation ≥ PExp +
0.02 MPa (0.2 bar)).
If there is still too much air in the heating installation at
the end of the check programme P.00, repeat the check
programme.
Filling and purging the hot water system
Open the cold water stop valve on the product.
Fill the hot water system by opening all the hot water
draw-off valves until water escapes.
2
Open all radiator valves (thermostatic radiator valves) of
the heating installation.
Fit the double non-return valve (1) of the filling line to
the cold water stop valve and secure the valve with the
spring clip (2).
To fill, first open the stop valve (3).
Open the stop valve (4) so that the water flows into the
heating system. Fill the heating system.
Purge the lowest radiator until water flows out of the
purging valve without bubbles.
Purge all other radiators until the entire heating system
has been filled with water.
Close all purging valves.
Monitor the rising filling pressure in the heating installation.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Start-up 7
7.14
Filling the condensate trap
7.15.2 Checking the leak-tightness of the flue gas
system and for flue gas recirculation
1.
2.
3.
4.
5.
6.
7.
8.
Check the integrity of the flue gas system.
If the flue gas system is longer than 2 m, we urgently
recommend that you test the system for flue gas recirculation as described below.
Use the air analysis point to check for flue gas recirculation.
Use the flue gas measuring instrument.
If you discover CO or CO2 in the fresh air, search for a
leak in the flue gas system or for the flue gas recirculation.
Eliminate the damage.
Repeat the above-mentioned test to determine if the
fresh air contains CO or CO2.
If you cannot eliminate the damage, you must not start
up the boiler.
7.15.3 Checking the gas flow rate
1
1.
Remove the lower section from the condensate trap (1).
2.
Fill the lower section with water up to 10 mm below the
upper edge.
Attach the lower section to the condensate trap.
3.
7.15
Gas ratio setting
7.15.1 Checking the factory-set gas ratio setting
Caution.
Risk of material damage caused by making unauthorised settings.
▶
▶
Never modify the factory setting of the gas
pressure regulator of the gas valve.
Before you start up the product, compare the gas group
information on the identification plate with the gas group
available at the installation site.
Conditions: The product design is not compatible with the local gas group
Only Vaillant Service Solutions may perform a gas conversion.
If a gas conversion to liquid gas has been carried out, the
smallest possible partial load is higher than is shown on the
display. The correct values can be found in the Technical
data in the appendix.
▶
▶
Call Vaillant Service Solutions (0330 1003 143).
Do not start up the product.
Conditions: The product design is compatible with the local gas group
▶
Proceed as described below.
0020209593_01 ecoTEC plus Installation and maintenance instructions
The boiler is fitted with a multifunctional automatic gas valve
which ensures that the precise air/gas ratio is provided under all operating conditions. The gas flow rate has been set
during production and does not require adjustment. With the
front casing fitted check the gas flow rate of the boiler as follows:
▶
▶
▶
▶
▶
▶
Start up the product with the check programme P.01.
In addition, ensure that maximum heat can be dissipated
into the heating system by turning up the room thermostat.
Wait at least 5 minutes until the boiler has reached its
operating temperature.
Ensure that all other gas appliances in the property are
turned off.
Measure the gas flow rate at the gas meter.
Compare the measured values with the corresponding
values in the table.
Nominal
value for
the net heat
supply
in kW in
accordance
with
BS EN 483
H gas in m³/h
P gas in kg/h
Nom.
+5%
−10% Nom.
+5%
−10%
12
1,31
1,38
1,18
0.96
1,01
0,86
15
1,64
1,72
1,48
1,20
1,26
1.08
18
1,97
2,07
1,77
1,44
1,51
1,30
24
2,61
2,74
2.35
1,92
2,02
1,73
30
3,27
3,43
2,94
2,40
2,52
2,16
37
4,03
4,23
3,63
2,96
3,11
2,66
25
2,72
2,86
2.45
2,00
2,10
1,80
32
3,41
3,58
3,07
2,52
2,65
2,27
35
3,78
3,97
3,40
2,78
2,92
2,50
38
4,15
4,36
3,73
3,05
3,20
2,75
25
7 Start-up
–
Conditions: Gas flow rate not in the permissible range
▶
▶
Check all of the piping and ensure that the gas flow rates
are correct.
Only put the product into operation once the gas flow
rates have been corrected.
9.
Conditions: Gas flow rate in the permissible range
▶
▶
▶
End the check programme P.01.
Allow the boiler to cool down by allowing pump overrun to
operate for a minimum of two minutes.
Record the boiler maximum gas flow rate onto the
Benchmark gas boiler commissioning checklist.
Conditions: Gas flow pressure not in the permissible range
Caution.
Risk of material damage and operating
faults caused by incorrect gas connection pressure.
If the gas connection pressure lies outside
the permissible range, this can cause operating faults in and damage to the product.
▶ Do not make any adjustments to the
product.
▶ Do not start up the product.
7.15.4 Checking the gas flow pressure
1.
2.
Ensure that the gas inlet working pressure can be
obtained with all other gas appliances in the property
working.
Close the gas isolator cock.
1
Permissible gas flow pressure for operation with
G20 natural gas: 1.3 … 2.3 kPa (13.0 … 23.0 mbar)
– Permissible gas flow pressure for operation with
G31 liquid gas: 2.3 … 4.3 kPa (23.0 … 43.0 mbar)
Should the pressure recorded at the reference test point
in the boiler be lower than indicated check if there is
any blockage in the pipework or if the pipework is undersized.
▶
▶
▶
▶
▶
▶
▶
▶
▶
▶
▶
If you cannot correct the failure, notify the gas supply
company and proceed as follows:
End the check programme P.01.
Allow the boiler to cool down by allowing pump overrun
to operate for a minimum of two minutes.
Close the gas isolator cock.
Remove the pressure gauge and retighten the sealing
screw (1) for the measuring nipple.
Open the gas isolator cock.
Check the measuring nipple for gas tightness.
Close the gas isolator cock.
Install the front casing.
Disconnect the product from the power mains.
You must not start up the boiler.
Conditions: Gas flow pressure in the permissible range
▶
▶
2
3.
4.
5.
6.
7.
8.
Use a screwdriver to undo the measuring nipple screw
(1) (lower screw) at the gas valve.
Connect a pressure gauge (2) to the measuring nipple
(1).
Open the gas isolator cock.
Start up the product with the check programme P.01.
In addition, ensure that maximum heat can be dissipated into the heating system by turning up the room
thermostat.
With the boiler operating at full load check that the gas
inlet working pressure at the reference test point complies with the requirements.
▶
▶
▶
▶
▶
▶
▶
7.15.5 Checking the CO₂ content and, if
necessary, adjusting it (air index setting)
1.
2.
3.
4.
26
End the check programme P.01.
Allow the boiler to cool down allowing pump overrun to
operate for a minimum of two minutes.
Close the gas isolator cock.
Remove the pressure gauge and retighten the sealing
screw (1) for the measuring nipple.
Open the gas isolator cock.
Check the measuring nipple for gas tightness.
Install the front casing.
Reset boiler controls for normal operation.
Record the appliance gas inlet working pressure (kPa
resp. mbar) in the Benchmark gas boiler commissioning
checklist.
Start up the product with the check programme P.01.
Wait at least five minutes until the product reaches its
operating temperature.
Measure the CO₂ and CO/CO₂ content at the flue gas
analysis point.
Compare the measured value with the corresponding
value in the table.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Start-up 7
Settings
Unit
G20
natural
gas
G31 liquid
gas
CO₂ after 5 minutes
in full load mode with
front casing closed
Vol.–%
9.2 ± 1.0
10.4 ± 0.5
CO₂ after 5 minutes
in full load mode with
front casing removed
Vol.–%
9.0 ± 1.0
10.2 ± 0.5
Set for Wobbe index
W₀
kWh/m³
14.09
21.34
O₂ after 5 minutes in
full load mode with
front casing closed
Vol.–%
CO value with full load
ppm
▶
▶
▶
▶
If an adjustment is not possible in the specified adjustment range, you must not start up the product.
If this is the case, inform Customer Service.
Screw the covering cap back in.
Install the front casing.
7.16
Before you hand the product over to the operator:
▶
▶
4.5 ± 1.8
CO/CO₂
5.1 ± 0.8
≤ 250
≤ 250
≤ 0.0031
≤ 0.0026
Conditions: The CO₂ content must be adjusted
Checking function and leak-tightness
▶
Check the gas line, the flue gas installation, the heating
installation and the hot water pipes for leaks.
Check that the air/flue pipe and condensate drain pipework have been installed correctly.
Check that the front casing has been installed correctly.
7.16.1 Checking the heating mode
1.
2.
Make sure that there is a heat requirement.
Call up the Live Monitor.
◁
1
If the product is working correctly, the display shows
S.04.
7.16.2 Checking the hot water generation
1.
2.
Open a hot water valve all the way.
Call up the Live Monitor.
◁
If the hot water generation is working correctly, S.14
appears in the display.
7.16.3 Checking the cylinder charging
Note
Cylinder charging is deactivated ex-works and
must be activated during initial start-up.
2
The cylinder charging of the shift-load cylinder is only active
if Comfort mode is switched on. If Comfort mode is activated,
the symbol "C" appears in the display ( Operating instructions).
When cylinder charging is switched on, the following temperatures can be set for the hot water temperature (see operating instructions):
▶
▶
▶
▶
▶
▶
▶
▶
▶
▶
Pierce the covering cap (1) at the mark using a small
flat-blade screwdriver and unscrew it.
After performing the adjustments, tilt the air intake pipe
back up.
Check the CO₂ content again.
If necessary, repeat the setting process.
Set the CO₂ content (value with front casing removed)
by turning the screw (2).
– Higher CO₂ content: Turn anti-clockwise
– Lower CO₂ content: Turn clockwise
For natural gas only: Only perform the adjustment in increments of 1 turn and wait approx. 1 minute after each
adjustment until the value stabilises.
For liquid gas only: Only perform the adjustment in small
increments (approx. 1/2 turn), and wait approx. 1 minute
after each adjustment until the value stabilises.
Check the CO₂ content again.
If necessary, repeat the setting process.
Press
(Cancel) once the adjustments have been
made.
0020209593_01 ecoTEC plus Installation and maintenance instructions
–
Minimum temperature 50 °C
Maximum temperature 65 °C
When cylinder charging is switched off, the following temperatures can be set for the hot water temperature:
–
Minimum temperature 35 °C
Maximum temperature 65 °C
If cylinder charging is switched off, the cylinder is not held
at temperature. If you draw off water, the boiler switches on
and, in this case, only operates on the through-flow principle.
▶
The product is equipped with an automatic Anti-legionella
function; if the temperature in the domestic hot water
cylinder falls below 50 °C, the cylinder is heated up to
70 °C once every 24 hours. If required, in consultation
with the operator, switch the Anti-legionella function off
using diagnostics code D.074.
27
8 Adapting the unit to the heating installation
▶
Overview of diagnostics codes (→ Page 43)
Call up the Live Monitor.
– Menu → Live Monitor
◁
7.17
1.
2.
3.
4.
5.
6.
7.
If the hot water generation is working correctly, S.24
appears in the display.
Thoroughly flushing the heating installation
("hot")
Operate the appliance until the boiler and the heating
system are up to temperature.
Check the heating system for leaks.
Connect a hose to the drain valve located at the lowest
position of the heating system.
Shut off the boiler, open the drain valve and all purge
valves on the radiators and allow the water to flow out
of the heating system and the boiler quickly and fully.
Close the drain valve.
Fill the heating system again with water as described in
Filling the heating installation (→ Page 24) and Purging
the heating installation (→ Page 24).
Re-fill the system until the system design pressure of
0,1 MPa (1,0 bar) is attained.
8.1
Burner anti-cycling time
To prevent frequent switching on and off of the burner and
thus prevent energy losses, an electronic restart lockout
is activated for a specific period each time the burner is
switched off. The burner anti-cycling time is only active
for the heating mode. Hot water handling during a burner
anti-cycling time does not affect the time function element
(default setting: 20 mins).
8.1.1
1.
2.
Navigate to Menu → Installer level → Diagnostics
menu → D.002 Max. anti-cycl. time: Heating and confirm by pressing
.
Set the burner anti-cycling time and confirm by pressing
.
TFlow
(target)
[°C]
Note
The actual reading on the digital pressure
gauge should ideally be 0,05 MPa (0,5 bar)
plus an additional pressure corresponding
to the highest point of the system above the
base of the boiler – 10 m head equals an additional 1 bar reading on the pressure gauge.
The minimum pressure should not be less
than 0,1 MPa (1 bar) in any installation. If
the system is to be treated with an inhibitor it
should be applied at this stage in accordance
with the manufacturer’s instructions. Further
information can be obtained from Sentinel,
Betz Dearborn Ltd., Tel: 0151 420 9595, or
Fernox, Alpha– Fry technologies. Tel: 0870
8700362.
8.
8
Adapting the unit to the heating
installation
To reset the most important system parameters, use the
Appliance config. menu point.
Or manually relaunch the installation assistant.
Menu → Installer level → Start inst. assistant
1
5
10
15
20
25
30
30
2.0
4.0
8.5
12.5
16.5
20.5
25.0
35
2.0
4.0
7.5
11.0
15.0
18.5
22.0
40
2.0
3.5
6.5
10.0
13.0
16.5
19.5
45
2.0
3.0
6.0
8.5
11.5
14.0
17.0
50
2.0
3.0
5.0
7.5
9.5
12.0
14.0
55
2.0
2.5
4.5
6.0
8.0
10.0
11.5
60
2.0
2.0
3.5
5.0
6.0
7.5
9.0
65
2.0
1.5
2.5
3.5
4.5
5.5
6.5
70
2.0
1.5
2.0
2.5
2.5
3.0
3.5
75
2.0
1.0
1.0
1.0
1.0
1.0
1.0
40
45
50
55
60
30
29.0
33.0
37.0
41.0
45.0
49.5
35
25.5
29.5
33.0
36.5
40.5
44.0
40
22.5
26.0
29.0
32.0
35.5
38.5
45
19.5
22.5
25.0
27.5
30.5
33.0
50
16.5
18.5
21.0
23.5
25.5
28.0
55
13.5
15.0
17.0
19.0
20.5
22.5
60
10.5
11.5
13.0
14.5
15.5
17.0
65
7.0
8.0
9.0
10.0
11.0
11.5
70
4.0
4.5
5.0
5.5
6.0
6.5
75
1.0
1.0
1.0
1.0
1.0
1.0
8.1.2
1.
Resetting the remaining burner anti-cycling
time
Alternatives 1 / 2
▶
Navigate to Menu Reset anti-cycl. time.
◁
Menu → Installer level Diagnostics menu
▶
Overview of diagnostics codes (→ Page 43)
1.
Set maximum burner anti-cycling time
[min]
35
You can find setting options in the Diagnostics menu.
28
Set maximum burner anti-cycling time [min]
TFlow
(target)
[°C]
Install the front casing.
Menu → Installer level Appliance config.
Setting the burner anti-cycling time
The current burner anti-cycling time appears in
the display.
Press
to reset the burner anti-cycling time.
Alternatives 2 / 2
▶
Press
.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Adapting the unit to the heating installation 8
8.2
1.
2.
Setting the maintenance interval
Navigate to Menu → Installer level → Diagnostics
menu → D.084 Maintenance in and confirm by pressing
.
Set the maintenance interval (operating hours) until the
next maintenance work is due and confirm by pressing
.
Heat demand
5.0 kW
10.0 kW
15.0 kW
20.0 kW
25.0 kW
> 27.0 kW
8.3
1.
2.
8.4
Number
of persons
Guideline value for burner
operating hours until the
next inspection/maintenance
work is due for an average
operating time of one year
(dependent upon the system
type)
1‑2
1050 h
2‑3
1150 h
1‑2
1500 h
2‑3
1600 h
2‑3
1800 h
3‑4
1900 h
3‑4
2600 h
4‑5
2700 h
3‑4
2800 h
4‑6
2900 h
3‑4
3000 h
4‑6
3000 h
Caution.
Risk of material damage caused by incorrect setting of the high-efficiency pump
If the pressure at the bypass valve is increased (by turning it clockwise) and the
pump output is set to less than 100%, the
product may not operate correctly.
▶
▶
Setting the pump output
▶
Navigate to Menu → Installer level → Diagnostics
menu → D.014 Pump speed target value and confirm
by pressing
.
Set the required pump output.
Remaining feed head of the pump
Remaining feed head [hPa]
8.3.1.1 Pump characteristic line for VUI 386
400
100% PWM
85%
70%
60%
53%
Minimum
with Auto
300
200
100
▶
8.5
▶
0
0
200
400
600
800
Remove the front casing. (→ Page 13)
1000 1200 1400 1600 1800
Flow rate [l/hr]
▶
▶
▶
▶
0020209593_01 ecoTEC plus Installation and maintenance instructions
Regulate the pressure using the adjusting screw (1).
Pressure
in MPa
(mbar)
Notes/application
Right-hand stop
(turned all the
way down)
0.035
(350)
If the radiators do not heat
up sufficiently at the default
setting. In this case, you
must set the pump to the
maximum speed.
Mid-position
(5 turns to the
left)
0.025
(250)
Default setting
5 further turns to
the left from the
mid-position
0.017
(170)
If noises are produced in
the radiators or radiator
valves
Position of the
adjusting screw
Switch off the speed regulation and set the pump output
to a fixed value.
8.3.1
In this case, set the pump output to
5 = 100% using diagnostics code D.014.
1
Conditions: Low loss header installed
▶
Setting the bypass valve
Install the front casing.
Handing the product over to the operator
When you have finished the installation, affix the enclosed sticker (which requests that the user reads the
instructions) to the front of the product in the operator's
language.
Explain to the operator how the safety devices work and
where they are located.
Inform the operator how to handle the product.
In particular, draw attention to the safety information
which the operator must follow.
Inform the operator of the necessity to have the product
maintained according to the specified intervals.
29
9 Troubleshooting
▶
▶
▶
▶
▶
Pass all of the instructions and documentation for the
product to the operator for safe-keeping.
Inform the operator about measures taken to ensure the
supply of combustion air and flue gas guiding, and instruct the operator that he must not make any changes.
Inform the operator that they must not store or use explosive or highly flammable substances (such as petrol,
paper or paint) in the installation room of the product.
Complete and sign off the Benchmark commissioning
check list.
Complete and sign off the guarantee documentation.
9
Troubleshooting
9.1
Checking service messages
appears if you have set a maintenance interval, for example, and this has passed or a service message is issued.
The product is not in fault mode.
▶
Navigate to Menu → Live Monitor and confirm by pressing
.
Conditions: S.40 is displayed
The product is in Comfort protection mode. The product continues to run with restricted comfort after it has detected a
fault.
▶
To establish whether or not a component is defective,
read the fault memory. (→ Page 30)
Note
If no fault message is present, the product will
automatically switch back to normal operating
mode after a certain time.
9.2
▶
Rectifying faults
If fault messages (F.XX) appear, rectify the fault by referring to the table in the appendix or using the Function
menu (→ Page 36) and the Check programs (→ Page 22).
9.4
1.
2.
Resetting parameters to factory settings
Navigate to Menu → Installer level → Diagnostics
menu → D.096 Reset to factory settings? and confirm by pressing
.
Set the diagnostics code to 1, and confirm by pressing
.
9.5
1.
2.
3.
4.
5.
6.
7.
8.
9.
Preparing the repair work
Decommission the product.
Disconnect the product from the power mains.
Remove the front casing. (→ Page 13)
Close the gas isolator cock.
Close the service valves in the heating flow and in the
heating return.
Close the service valve in the cold water pipe.
Drain the product if you want to replace water-bearing
components of the product.
Make sure that water does not drip on live components
(e.g. the electronics box).
Use only new seals.
9.5.1
Procuring spare parts
The original components of the product were also certified
as part of the declaration of conformity. If you do not use certified Vaillant original spare parts for maintenance or repair
work, this voids the conformity of the product. We therefore
strongly recommend that you fit Vaillant genuine spare parts.
Information about available Vaillant original spare parts is
available by contacting the contact address provided on the
reverse of this document.
▶
If you require spare parts for maintenance or repair work,
use only Vaillant genuine spare parts.
9.6
Replacing defective components
9.6.1
Replacing the burner
1.
Remove the compact thermal module. (→ Page 36)
If several faults occur at the same time, the display shows
the corresponding fault messages for two seconds each in
alternation.
▶
▶
1
Press
(max. three times) to restart the product.
If you are unable to remedy the fault and the fault recurs
despite fault clearance attempts, contact customer service.
9.3
Calling up and clearing the fault memory
The last 10 fault messages are stored in the fault memory.
▶
Navigate to the Fault list menu.
◁
▶
▶
30
The display shows the number of faults that have
occurred, the fault numbers and the corresponding
plain text display.
Press
Press
or
to call up individual fault messages.
twice to delete the fault list.
2
2.
3.
4.
5.
Undo the four screws (1) on the burner.
Remove the burner.
Install a new seal (2) on the new burner.
Install the compact thermal module. (→ Page 38)
Installation and maintenance instructions ecoTEC plus 0020209593_01
Troubleshooting 9
9.6.2
Replacing the fan
1
2
7
2
3
4
1
5
6
1.
2.
3.
4.
5.
6.
Remove the air intake pipe.
Remove the three plugs from the gas valve (5 ).
Remove the plug from the sensor on the Venturi (3) by
pushing in the latching lug.
Remove the plug/plugs (4) (depending on the unit
design) from the fan motor by pushing in the latching
lug in each case.
Unscrew the two cap nuts (7) and (6) on the gas valve.
Use an open-ended spanner to counterhold the opposite side of the gas valve when unscrewing.
Unscrew the three screws (2) between the mixture pipe
(1) and the fan flange.
11. Remove the gas valve retainer (1) from the fan by unscrewing the three screws (2).
12. Replace the defective fan.
2
1
3
5
4
1
13. Refit the components in the reverse order. New seals
(4) and (5) must be used for this. Pay attention to the
order in which the three screws between the fan and
the mixture pipe are screwed in, as per the numbering
(1), (2) and (3).
14. Screw the flexible gas line to the gas valve. Use new
seals for this.
15. When tightening the cap nut on the gas valve, use an
open-ended spanner to counterhold the opposite side
of the gas valve.
16. Perform a gas family check after installing the new fan.
(→ Page 21)
3
2
7.
Remove the entire unit comprising the fan, Venturi and
gas valve from the product.
8. Unscrew the gas valve fixing screw (2) from the retainer.
9. Remove the gas valve from the retainer.
10. Remove the Venturi (3), including the gas connection
pipe (1), from the fan by turning the bayonet fitting on
the Venturi anti-clockwise as far as it goes and removing it straight from the fan.
0020209593_01 ecoTEC plus Installation and maintenance instructions
9.6.3
Replacing the gas valve
Note
To replace the gas valve, you will need a Torx
T20. To replace the gas valve directly from the
front, you will need an offset screwdriver or a Torx
T20 socket. If you do not have access to an offset screwdriver or the like, you must first remove
the entire unit comprising the fan with gas valve
before you can remove the gas valve from the retainer.
31
9 Troubleshooting
5
1
9.6.4
Replacing the Venturi
1
2
2
4
3
3
1.
Remove the air intake pipe.
2.
3.
Remove the three plugs from the gas valve (2).
Remove the plug from the sensor on the Venturi (1) by
pushing in the latching lug.
Unscrew the two cap nuts (5) and (4) on the gas valve.
Use an open-ended spanner to counterhold the opposite side of the gas valve (4) and (5) when unscrewing.
Either remove the unit comprising the fan with gas valve
(Replacing the fan (→ Page 31)), or use an offset screwdriver or Torx T20 socket to unscrew the fixing screw of
gas valve (3) from the retainer.
4.
5.
Note
The screw in the gas valve retainer secures
the gas valve against turning and must be
screwed back in once the gas valve has
been replaced.
6.
7.
8.
9.
Remove the gas valve from the retainer.
Reinstall the new gas valve in the reverse order. Use
new seals for this.
When tightening the cap nuts on the gas valve, use an
open-ended spanner to counterhold the opposite side of
the gas valve (4) and (5).
After installing the new gas valve, perform a leak-tightness test (→ Page 27), gas family check (→ Page 21)
and gas ratio setting (→ Page 25).
1.
Remove the air intake pipe.
2.
Remove the plug from the sensor on the Venturi (1) by
pushing in the latching lug.
Unscrew the cap nuts (3) of the gas connection pipe (2)
on the gas valve.
Remove the Venturi, including the gas connection pipe,
from the fan by turning the bayonet fitting on the Venturi
anti-clockwise as far as it goes and removing it straight
from the fan.
3.
4.
7
1
6
2
5
4
3
5.
6.
7.
Remove the gas connection pipe (1) from the Venturi
(3) by removing the clamp (4) and pulling the gas connection pipe out vertically. Dispose of the seal (7).
Pull the gas restrictor (6) straight off, and keep it for reuse.
Check whether the Venturi is free of residue at the gas
inlet side.
Caution.
Risk of material damage to the product.
Lubricant can block function-related channels
in the Venturi.
▶
8.
32
Do not use lubricant when installing the
gas restrictor.
Ensure that you use the correct gas restrictor (colour
coding and position of pins on the underside of the gas
Installation and maintenance instructions ecoTEC plus 0020209593_01
Troubleshooting 9
9.
10.
11.
12.
13.
14.
restrictor). The colour of the gas restrictor must match
the colour of the coding resistor on the PCB.
Insert the gas restrictor for the gas group in question
into the new Venturi (yellow: G20 natural gas, grey:
Liquid gas).
When inserting the gas restrictor, ensure that the gas
restrictor is correctly aligned using the indicated position marks on the upper side of the Venturi and also
the positioning pins (5) on the underside of the gas restrictor.
Refit the components in the reverse order. Use new
seals for this.
After installing the new Venturi, carry out a gas ratio
setting. (→ Page 25)
If you cannot adjust the CO2 content, the gas restrictor
has been damaged during installation. In this case,
replace the gas restrictor with an appropriate spare
part.
Perform a gas family check. (→ Page 21)
9.6.5
1.
2.
3.
Replacing the heat exchanger
Drain the product. (→ Page 39)
Remove the compact thermal module. (→ Page 36)
Detach the condensate drain hose from the heat exchanger.
1
1
2
8.
Remove the lower three screws (2) on the rear section
of the retainer.
9. Swing the retainer to the side around the top screw (1).
10. Pull the heat exchanger downwards and to the right,
and remove it from the product.
11. Install the new heat exchanger in reverse order.
12. Replace the seals.
Note
Instead of grease, use only water or commercially available soft soap to aid installation.
2
3
13. Insert the flow and return connections into the heat
exchanger as far as they will go.
14. Make sure that the brackets are seated correctly on the
flow and return connections.
15. Install the compact thermal module. (→ Page 38)
4.
Remove the clamps (2) and (3) from the flow connection and the return connection.
16. Fill and purge the product and, if necessary, the heating
installation. (→ Page 24)
5.
6.
7.
Detach the flow connection.
Detach the return connection.
Remove two screws (1) on each of the two retainers.
9.6.6
1.
Replacing the expansion vessel on the heat
generator
Drain the product. (→ Page 39)
1
2
3
4
2.
3.
4.
0020209593_01 ecoTEC plus Installation and maintenance instructions
Undo the screwed connection (4).
Remove both screws (1) on the support plate (2).
Remove the support plate (2).
33
9 Troubleshooting
5.
6.
7.
Pull out the expansion vessel (3) towards the front.
Insert the new expansion vessel into the product.
Screw the new expansion vessel to the water connection. Use a new seal for this.
Attach the support plate using both screws (1).
Fill and purge the product and, if necessary, the heating
installation. (→ Page 24)
8.
9.
9.6.7
1.
2.
1
Replacing the expansion vessel on the
shift-load cylinder
Close the cold water stop valve.
Open a hot water valve to depressurise the water circuit. Close the hot water valve.
Unscrew the screw from the cover of the shift-load cylinder.
Remove the cover.
3.
4.
6
5
4
2
2
3
1
5.
6.
Undo the nuts (2) on the expansion vessel (1).
Detach the expansion vessel from the screwed pipe
and remove it from the EPS insulation.
7. Insert the new expansion vessel into the EPS insulation.
8. Connect the new expansion vessel. To do this, use a
new seal.
9. Check the filling pressure of the expansion vessel (minimum pressure is 0.4 MPa (4 bar)).
10. Fill and purge the heat generator and the shift-load
cylinder.
2.
Remove the discharge pipe (1) from the expansion relief valve on the heat generator.
3.
4.
5.
6.
Tilt the heat generator's electronics box forward.
Open the electronics box.
Pull the X12 plug out of the PCB.
Pull the free end of the line carefully through the grommets on the heat generator and on the shift-load cylinder.
Detach the pump sensor line from the cable harness by
pulling the plug out of the cable harness.
Unscrew the pipe elbow (6) from the casing.
Undo the screwed connection (2) on the connection
pipe (3).
Detach the spring clip (5) from the casing of the cylinder charging pump (4). At the same time, use your free
hand to support the cylinder charging pump to ensure
that it does not fall out of the casing.
Pull the cylinder charging pump downwards out of the
casing.
Install the pipe elbow on the new cylinder charging
pump and use new seals for it.
Install the new cylinder charging pump in reverse order
and use new seals.
Connect the pump's electrical lines in reverse order. In
doing so, pay attention to the correct pipe routing.
Reinstall the discharge pipe (1) and use new seals.
Fill and purge the heat generator and the shift-load
cylinder.
7.
8.
9.
10.
11.
12.
9.6.8
1.
34
Replacing the cylinder charging pump on
the shift-load cylinder
Close the hot water system stop valves and drain the
heat generator and shift-load cylinder on the hot water
side.
13.
14.
15.
16.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Troubleshooting 9
9.6.9
Close the hot water system stop valves and drain the
heat generator and shift-load cylinder on the hot water
side.
X12
X31
1.
Replacing the impeller sensor on the shiftload cylinder
1
1
3.
5
4
4.
If you are replacing the PCB, remove the coding resistance (1) (plug X24) from the old PCB and plug the plug
onto the new PCB.
Close the electronics box.
9.6.11 Replacing the PCB and display for the heat
generator
1.
2.
2
X12
X31
3
Open the electronics box. (→ Page 18)
Replace the PCB and display according to the
assembly and installation instructions supplied.
2.
1
Remove the discharge pipe (1) from the expansion relief valve on the heat generator.
3.
4.
Remove the plug from the impeller sensor.
Undo the screwed connections (2) and (3) on the angle
pieces (4) and (5).
5. Turn the impeller sensor slightly to the side and pull it
downwards to remove it from the casing.
6. Remove the pipe elbow from the impeller sensor.
7. Install the pipe elbow on the new impeller sensor and
use new seals for it.
8. Install the new impeller sensor in reverse order and use
new seals.
9. Connect the connection cable plug to the new impeller
sensor.
10. Reinstall the discharge pipe (1) and use new seals.
11. Fill and purge the heat generator and the shift-load
cylinder.
3.
4.
5.
◁
6.
7.
0020209593_01 ecoTEC plus Installation and maintenance instructions
You are automatically taken to D.093 to set the
device specific number.
Set the correct value for the relevant product type in accordance with the table below and confirm by pressing
.
Product type number
938 (VUI GB 386/5‑5 A)
ecoTEC plus
Note
If you only replace one component, when the
product is switched on, the new component adopts the parameters that were previously set from
the component that was not replaced.
Open the electronics box. (→ Page 18)
Replace the PCB or display according to the assembly
and installation instructions supplied.
After switching on, the product switches directly to
the menu to select the language. The default language setting is English.
Select the required language and confirm by pressing
.
◁
9.6.10 Replacing the PCB or display for the heat
generator
1.
2.
Remove the coding resistance (1) (plug X24) from the
old PCB and plug the plug into the new PCB.
Close the electronics box.
Press the on/off button on the product. (→ Page 20)
◁
◁
8.
17
The electronics are now set to the product type and
the parameters of all diagnostics codes are set to
default settings.
The installation assistant starts.
Make the system-specific settings.
35
10 Inspection and maintenance
9.6.12 Replacing the PCB on the shift-load
cylinder
1.
2.
Comply with the assembly and installation instructions
provided with the spare parts.
Unscrew the screw from the cover of the shift-load cylinder and remove the cover.
1
–
–
–
–
–
The gas inlet working pressure at maximum rate.
The gas flow rates.
Correctness of electrical, water and gas connections.
Correctness of the water pressure.
The condition of the whole system, in particular the condition of radiator valves, evidence of leakage from the
heating system and dripping taps.
▶
Correct any faults before proceeding.
10.1
Function menu
Menu → Installer level → Test programs → Function menu
The function menu allows you to actuate and test individual
components in the heating installation.
Test
programme
Action
T.01
Check internal
pump
Switch the internal pump on
and off.
T.02
Check 3-way
valve
Move the diverter valve to
the heating position or to the
hot water position.
T.03
Check fan
Switch the fan on and off.
The fan runs at maximum
rotational speed.
T.04
Check cylinder
charge pump
Switch the cylinder charging
pump on and off.
T.05
Check circulation pump
Switch the circulation pump
on and off.
T.06
Check external
pump
Switch the external pump on
and off.
T.08
Checking the
burner
Product starts up and
switches to minimum load.
The flow temperature is
shown in the display.
Display
3.
4.
5.
6.
9.7
1.
2.
3.
4.
5.
10
▶
Remove the electronics box with the shift-load cylinder
PCB (1) from the appliance slot.
Open the electronics box and remove the plug from the
PCB.
Install the new PCB in reverse order.
Start up the product.
Completing repair work
Establish the power supply.
Switch the product back on if this has not yet been
done. (→ Page 20)
Install the front casing.
Open all service valves and the gas isolator cock.
Check that it works correctly and is leak-tight.
(→ Page 27)
Inspection and maintenance
You must carry out an annual inspection of the product.
The annual inspection can be effectively performed
without removing components by requesting data from
the DIA system, carrying out the simple visual checks indicated in the table in the appendix and performing a flue
gas measurement. The maintenance intervals and their
scope are determined by the heating engineer based on
the condition of the boiler found during the inspection. All
inspection and maintenance work should be performed in
the order specified in the table in the appendix.
Inspection and maintenance work – Overview
(→ Page 53)
During any inspection and maintenance or after change
of parts of the combustion circuit, the following must be
checked:
–
–
–
36
The boiler has been installed in accordance with the relevant installation instructions.
The integrity of the flue gas installation and flue seals is
in accordance with the relevant flue installation instructions enclosed.
Visual, the integrity of the boiler combustion circuit and
relevant seals (paying particular attention to the burner
door seal).
10.2
Electronics self-test
Menu → Installer level → Test programs → Electronics
self-test
You can use the electronics self-test to check the PCB.
10.3
Removing the compact thermal module
Note
The compact thermal module consists of five main
components:
– Speed-regulated fan,
– Gas valve including support plate,
– Venturi including mass flow sensor and gas
connection pipe,
– Burner flange,
– Premix burner.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Inspection and maintenance 10
Danger!
Risk of death and risk of material damage
caused by hot flue gas.
The seal, insulating mat and self-locking nuts
on the burner flange must not be damaged.
Otherwise, hot flue gases may escape and
cause personal injury and material damage.
▶
▶
▶
1.
2.
3.
4.
Replace the seal each time you open the
burner flange.
Replace the self-locking nuts on the
burner flange each time you open the
burner flange.
If the insulating mat on the burner flange
or on the back wall of the heat exchanger
shows signs of damage, replace the insulating mat.
Switch off the product using the on/off button.
Close the gas isolator cock.
Remove the front casing. (→ Page 13)
Tilt the electronics box forward.
8
1
2
7
3
6
4
5
7.
8.
1
2
3
9.
10.
11.
12.
13.
14.
15.
16.
17.
4
10.4
5.
Unscrew the retaining screw (2) and remove the air
intake pipe (1) from the intake stub.
6.
Unscrew either the cap nut on the gas valve (3) or the
cap nut (4) between the corrugated gas pipe and the
fixed gas pipe.
1.
Remove the plugs of the ignition line (7) and of the
ground connection (6) from the ignition electrode.
Remove the plug (4) from the fan motor by pushing in
the latching lug.
Remove the three plugs from the gas valve (5).
Remove the plug from the Venturi (3) by pushing in the
latching lug.
Release the cable harness from the clip on the gas
valve retainer.
Unscrew the four nuts (8).
Remove the entire compact thermal module (2) from
the heat exchanger (1).
Check the burner and the heat exchanger for damage
and dirt.
If necessary, clean or replace the components according to the following sections.
Fit a new burner flange seal.
Check the insulating mat on the burner flange and on
the back wall of the heat exchanger. If you notice any
signs of damage, replace the relevant insulating mat.
Cleaning the heat exchanger
Protect the folded down electronics box against sprayed
water.
2
3
1
2.
3.
0020209593_01 ecoTEC plus Installation and maintenance instructions
4
Never undo the four nuts on the stud bolt (1) or tighten
them.
Clean the heating coil (3) of the heat exchanger (4) using water or, if required, vinegar (to a maximum of 5%
acid). Allow the vinegar to act on the heat exchanger for
20 minutes.
37
10 Inspection and maintenance
4.
Rinse away any loose dirt with a sharp jet of water or
use a plastic brush. Do not point the water jet directly
at the insulating mat (2) on the back of the heat exchanger.
◁
10.5
The water flows out of the heat exchanger through
the condensate trap.
Checking the burner
1
2.
3.
4.
5.
6.
Drain the product on the hot water side (3).
Unscrew the cap nut (1) from the cold water pipe.
Undo the nut (2) on the connector (5).
Unscrew the cap nut (4).
Remove the connector, including the connection pipe
(6).
7. Rinse the connector out under flowing water in the opposite direction to the normal flow.
8. Refit the connector with the cleaned filter.
9. Always use new seals and retighten the nut and the two
cap nuts.
10. Open the cold water stop valve.
10.8
Installing the compact thermal module
8
1
2
7
3
2
3
1.
2.
3.
10.6
1.
2.
3.
4.
10.7
Check the surface of the burner (1) for damage. If you
see any damage, replace the burner.
Fit a new burner flange seal (3).
Check the insulating mat (2) on the burner flange. If you
notice any signs of damage, replace the insulating mat.
Remove the lower section of the condensate trap (1).
Flush out the lower section with water.
Fill the lower section with water up to about 10 mm below the upper edge.
Attach the lower section to the condensate trap.
Cleaning the filter in the cold water inlet
6
38
4
5
Cleaning the condensate trap
2
1
1.
6
5
3
1.
Connect the compact thermal module (2) to the heat
exchanger (1).
2. Tighten the four nuts (8) in a cross-wise pattern until the
burner flange fits closely and uniformly onto the mating
surfaces (if a torque spanner is available, set at 6 Nm).
3. Reconnect the plugs (3) to (7).
4. Connect the gas line using a new seal. In the process,
secure the gas pipe against twisting.
5. Open the gas isolator cock.
6. Make sure that there are no leaks.
7. Check that the sealing ring in the air intake pipe is positioned correctly in the seal seat.
8. Reconnect the air intake pipe to the intake nozzle.
9. Secure the air intake pipe with the retaining screw.
10. Check the gas flow pressure.
4
Close the cold water stop valve.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Decommissioning 11
10.9
1.
2.
3.
4.
Draining the product
Close the service valves of the product.
Start the check programme P.06 (diverter valve midposition).
Open the drain valves.
Make sure that the cap of the automatic air vent on
the internal pump is open so that the product can be
drained fully.
1
2
10.10 Checking the pre-charge pressure for
the internal expansion vessel on the heat
generator
1.
2.
Close the service valves and drain the product.
Measure the pre-charge pressure of the expansion vessel at the vessel valve.
Conditions: Pre-charge pressure < 0.075 MPa (0.75 bar)
▶
3.
4.
5.
Ideally, you should top up the expansion vessel with
nitrogen. Otherwise, top it up with air. Ensure that the
drain valve is open when topping up.
If water escapes from the valve of the expansion
vessel, you must replace the expansion vessel.
(→ Page 33)
Fill the heating installation. (→ Page 24)
Purge the heating installation. (→ Page 24)
10.11 Checking the pre-charge pressure of the
shift-load cylinder expansion vessel
Note
One check every three years is sufficient.
6.
Unscrew the sealing cap (2) from the expansion vessel
(1).
7. Check whether the pre-charge pressure of the expansion vessel is approx. 0.4 MPa (4 bar). If the pressure is
lower than this, increase it using an air pump until it is
0.4 MPa (4 bar).
8. Screw the sealing cap (2) back onto the expansion vessel.
9. Reinstall the cover.
10. Repressurise the heat generator and the hot water system.
10.12 Completing inspection and maintenance
work
Once you have completed all maintenance work:
1.
2.
3.
4.
5.
Close the stop valves on the hot water system.
Close the cold water stop valve.
Open a hot water valve to depressurise the water circuit. Close the hot water valve.
Unscrew the screw from the cover of the shift-load cylinder.
Remove the cover.
◁
The expansion vessel is freely accessible.
▶
▶
▶
Check the gas flow pressure. (→ Page 26)
Check the CO₂ content and, if necessary, adjust it (air
index setting). (→ Page 26)
If required, reset the maintenance interval. (→ Page 29)
11
Decommissioning
11.1
▶
Press the on/off button.
◁
▶
▶
0020209593_01 ecoTEC plus Installation and maintenance instructions
Temporarily decommissioning the product
The display goes out.
Close the gas isolator cock.
For products with hot water generation and products with
a connected domestic hot water cylinder, you must also
close the cold water stop valve.
39
12 Recycling and disposal
11.2
▶
Press the on/off button.
◁
▶
▶
▶
▶
12
Decommissioning the product
The display goes out.
Disconnect the product from the power mains.
Close the gas isolator cock.
Close the cold water stop valve.
Drain the product. (→ Page 39)
Recycling and disposal
Disposing of the packaging
▶
▶
13
Dispose of the packaging correctly.
Observe all relevant regulations.
Customer service
To ensure regular servicing, it is strongly recommended
that arrangements are made for a Maintenance Agreement.
Please contact Vaillant Service Solutions for further details.
Vaillant Service Solutions: 0330 100 3461
40
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Appendix
A
Installer level – Overview
Setting level
Values
Min.
Max.
00
99
Unit
Increment, select, explanation
Default
setting
Installer level →
Enter code
–
1 (competent person code 17)
–
Installer level → List of faults →
F.XX - F.XX¹
–
–
Current value
–
Current value
–
LPG, natural gas
–
Installer level → Test programs →
Gas type check
Installer level → Test programs → Check programs →
P.00 Purging
–
–
–
Yes, No
–
P.01 Maximum load
–
–
–
Yes, No
–
P.02 Minimum load
–
–
–
Yes, No
–
P.06 Filling mode
–
–
–
Yes, No
–
Installer level → Test programs → Function menu →
T.01 Internal pump
–
–
–
On, Off
–
T.02 3-way valve
–
–
–
On, Off
–
T.03 Fan
–
–
–
On, Off
–
T.04 Cyl. charging pump
–
–
–
On, Off
–
T.05 Circulation pump
–
–
–
On, Off
–
T.06 External pump
–
–
–
On, Off
–
T.08 Burner
–
–
–
On, Off
–
–
Installer level → Test programs → Electronics self-test →
–
–
–
Yes, No
–
–
–
Deutsch, English, Français, Italiano, Dansk,
Nederlands, Castellano, Türkce, Magyar,
Pусский, Українськa, Svenska, Norsk, Polski, Čeština, Hrvatski, Slovenčina, Română,
Slovenščina, Português, Srpski
Flow temp. setpoint
30
75
℃
1
–
DHW temperature
30
60
℃
1
Product with hot water generation or connected
domestic hot water cylinder
–
–
–
–
On, Off
Self-test
Installer level → Appliance config. →
Language
Comfort mode
English
Off
¹Fault lists are only displayed, and can only be deleted, if faults have occurred.
0020209593_01 ecoTEC plus Installation and maintenance instructions
41
Appendix
Setting level
Values
Unit
Increment, select, explanation
Default
setting
Min.
Max.
Auxiliary relay
1
10
–
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2
Accessory relay 1
1
10
–
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2
Accessory relay 2
1
10
–
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2
Heating partial load
–
–
kW
Phone
number
–
–
Contact data
Default setting
Partial load only, full load only, auto
Auto
–
0–9
Auto
–
–
On, Off
Current value
–
–
Installer level → Diagnostics menu →
D.XXX - D.XXX
–
–
Installer level → Start ins. assistant →
Language
–
–
–
Deutsch, English, Français, Italiano, Dansk,
Nederlands, Castellano, Türkce, Magyar,
Pусский, Українськa, Svenska, Norsk, Polski, Čeština, Hrvatski, Slovenčina, Română,
Slovenščina, Português, Srpski
Filling mode: 3-way valve is in midposition
0
2
–
0 = Normal operating mode
1 = Mid-position (parallel operation)
2 = Permanent heating mode position
–
Purge programme
–
–
–
Automatic adaptive purging of the heating circuit
and hot water circuit
Not active
Active
–
Flow temp. setpoint
30
75
℃
1
–
DHW temperature
35
60
℃
1
Product with hot water generation
–
English
¹Fault lists are only displayed, and can only be deleted, if faults have occurred.
42
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Setting level
Values
Unit
Default
setting
Increment, select, explanation
Min.
Max.
Comfort mode
–
–
–
Heating partial load
–
–
kW
Auxiliary relay
1
10
–
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2
Accessory relay 1
1
10
–
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2
1
10
–
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2
0-9
–
Yes, No
–
Accessory relay 2
Contact data
Phone number
End the installation assistant?
–
–
–
–
–
On, Off
Partial load only, full load only, auto
Auto
¹Fault lists are only displayed, and can only be deleted, if faults have occurred.
B
Code
Overview of diagnostics codes
Parameter
Values or explanations
Default
setting
Own setting
D.000 Heating partial load
Adjustable heating partial load in kW
Auto: Product automatically adjusts max. partial load to
current system demand
Auto
D.001 Overrun time of internal heating
pump for heating mode
1 … 60 min
5 min
D.002 Max. burner anti-cycling time heating
at 20 °C flow temperature
2 … 60 min
20 min
D.003 Outlet temp. actual value
In °C
Not adjustable
D.004 Measured value of hot water sensor
In °C
Not adjustable
D.005 Flow temperature target value (or
return target value)
In °C, max. of the value set in D.071, limited by an eBUS
controller if connected
Not adjustable
D.006 Hot water temperature target value
(only products with integrated hot
water generation)
35 … 65 ℃
Not adjustable
0020209593_01 ecoTEC plus Installation and maintenance instructions
43
Appendix
Code
Parameter
Values or explanations
Default
setting
Own setting
D.007 Warm start temperature target value
35 … 65 ℃
Not adjustable
D.008 Room thermostat at terminal RT
Room thermostat open (no heat requirement)
Room thermostat closed (heat requirement)
Not adjustable
D.009 Target value from external eBUS
controller
In °C
Not adjustable
D.010 Status of internal heating pump
On, Off
Not adjustable
D.011 Status of external heating pump
On, Off
Not adjustable
D.012 Status of cylinder charge pump
On, Off
Not adjustable
D.013 Status of hot water circulation pump
On, Off
Not adjustable
D.014 Target pump speed (high-efficiency
pump)
Target value of internal high-efficiency pump in %. Possible settings:
0 = Auto
1 = 53
2 = 60
3 = 70
4 = 85
5 = 100
D.015 Actual pump speed (high-efficiency
pump)
Actual value for internal high-efficiency pump in %
Not adjustable
D.016 24 V DC room thermostat
open/closed
Heating mode off/on
Not adjustable
D.017 Heating flow/return flow temperature
control changeover
Control type:
0 = Flow, 1 = Return
Return: Automatic detection function for heating output
inactive. Max. possible heating partial load when D.000
is on Auto.
0 = Flow
D.018 Pump operating mode setting
1 = Comfort (continuously operating pump)
Internal pump is switched on when the heating flow temperature is not at Heating off and the heat requirement
is enabled via an external controller
3 = Eco (intermittently operating pump)
Internal pump is switched on every 25 minutes for 5
minutes once the overrun time has elapsed
3 = Eco
D.019 Operating mode of 2-stage pump
Not relevant
0 = Auto
Not adjustable
D.020 Max. setting for cylinder target value
Adjustment range: 50 - 70 °C (actoSTOR 65 °C)
D.022 Hot water requirement (via C1/C2,
impeller or APC)
On, Off
Not adjustable
D.023 Summer/winter mode (heating off/on)
Heating on, heating off (summer mode)
Not adjustable
D.025 Hot water generation enabled by
eBUS controller
On, Off
Not adjustable
D.026 Auxiliary relay control
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
44
65 °C
2 = External
pump
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Code
Parameter
Values or explanations
Default
setting
Own setting
D.027 Switching of relay 1 on the VR 40 "2
in 7" multi-functional module
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2 = External
pump
D.028 Switching of relay 2 on the VR 40 "2
in 7" multi-functional module
1 = Circulation pump
2 = External pump
3 = Cylinder charging pump
4 = Extractor hood
5 = External solenoid valve
6 = External fault message
7 = Solar pump (not active)
8 = eBUS remote control (not active)
9 = Legionella protection pump (not active)
10 = Solar valve (not active)
2 = External
pump
D.033 Fan speed target value
In rpm
Not adjustable
D.034 Fan speed actual value
In rpm
Not adjustable
D.035 Position of the diverter valve
Heating mode
Parallel operation (mid-position)
DHW mode
Not adjustable
D.036 Hot water flow volume (impeller
sensor)
In l/min
Not adjustable
D.039 Solar feed temperature
Actual value in °C
Not adjustable
D.040 Flow temperature
Actual value in °C
Not adjustable
D.041 Return temperature
Actual value in °C
Not adjustable
D.044 Digitised ionisation value
Display field 0 to 1020
> 800 no flame
< 400 good flame
Not adjustable
D.046 Pump type
0 = Relay with disable facility
1 = PWM with disable facility
D.047 Outside temperature (with Vaillant
weather compensator)
Actual value in °C
D.050 Offset for minimum speed
In rpm, setting range: 0 to 3000
Nominal
value set in
factory
D.051 Offset for maximum speed
In rpm, setting range: -990 to 0
Nominal
value set in
factory
D.058 Activating solar post-heating ( only
products with integrated hot water
generation)
0 = Solar post-heating deactivated
3 = DHW activation target value minimum 60 °C, thermostatic mixer valve required between product and draw-off
point
0 = Solar
post-heating
deactivated
D.060 Number of temperature limiter shutdowns
Number of shutdowns
Not adjustable
D.061 Number of ignition device cutoffs
Number of unsuccessful ignitions in the last attempt
Not adjustable
0020209593_01 ecoTEC plus Installation and maintenance instructions
0 = Relay
with disable
facility
Not adjustable
45
Appendix
Code
Parameter
Values or explanations
Default
setting
Own setting
D.064 Average ignition time
In seconds
Not adjustable
D.065 Maximum ignition time
In seconds
Not adjustable
D.067 Remaining burner anti-cycling time
In minutes
Not adjustable
D.068 Unsuccessful ignitions at 1st attempt
Number of unsuccessful ignitions
Not adjustable
D.069 Unsuccessful ignitions at 2nd attempt
Number of unsuccessful ignitions
Not adjustable
D.070 Set diverter valve position
0 = Normal operating mode
1 = Parallel operation (mid-position)
2 = Permanent heating mode position
0 = Normal
operating
mode
D.071 Target value maximum heating flow
temperature
40 … 80 ℃
75 ℃
D.072 Internal pump overrun after cylinder
charging
Adjustable from 0-10 minutes in increments of 1 minute
2 mins
D.073 Warm start target offset
Adjustable from -15 K to 5 K
0
D.074 actoSTOR anti-legionella function
0 = Off
1 = On
1 = On
D.075 Max. charging time for domestic hot
water cylinder without independent
control system
20 - 90 min
45 mins
D.076 Device Specific Number Device
specific number = DSN)
17 = 938 (VUI GB 386/5-5 A)
D.077 Limit on cylinder charging output in
kW
Adjustable cylinder charging output in kW
D.078 Limit on cylinder charging temperature in °C
50 °C - 80 °C
Note
The chosen value must be at least 15 K or 15 °C above
the set cylinder target value.
75 °C
D.080 Operating hours, heating
In hours (h)
Not adjustable
D.081 Operating hours, hot water generation
In hours (h)
Not adjustable
D.082 Number of burner start-ups in heating mode
Number of burner start-ups
Not adjustable
D.083 Number of burner start-ups in hot
water mode
Number of burner start-ups
Not adjustable
D.084 Maintenance indicator: Number of
hours until the next maintenance
Adjustment range: 0 to 3000 hrs and "---" for deactivated
„---”
D.088 Start delay for hot water draw-off
detection via impeller (only products
with integrated hot water generation)
0 = 1.5 l/min and no delay,
1 = 3.7 l/min and 2 sec. delay
1.5 l/min and
no delay
D.090 Status of digital controller
Recognised, not recognised
Not adjustable
D.091 Status of DCF with external temperature sensor connected
No reception
Reception
Synchronised
Valid
Not adjustable
D.092 actoSTOR module recognition
0 = Not connected
1 = Connection error: No communication via PeBus,
actoSTOR module detected previously
2 = Connection active
Not adjustable
D.093 Setting the Device Specific Number
(DSN)
Setting range: 0 to 99
46
Not adjustable
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Code
Parameter
Values or explanations
D.094 Delete fault history
Delete fault list
0 = No
1 = Yes
D.095 Software version of PeBUS components
PCB (BMU)
Display (AI)
actoSTOR (APC)
HBI/VR34
D.096 Default setting
Reset all adjustable parameters to factory setting
0 = No
1 = Yes
D.098 Value of coding resistances for gas
group and output range
Display xx.yy
xx = Coding resistance 1 in cable harness for output
range:
11 = 938 (VUI GB 386/5-5 A)
yy = Coding resistance 2 on PCB for gas group:
02 = P gas
03 = H gas
C
Default
setting
Own setting
Not adjustable
Not adjustable
Status codes – Overview
Status code
Meaning
Heating mode
S.00
Heating: No heat demand
S.01
Heating mode: Fan start-up
S.02
Heating mode: Pump pre-run
S.03
Heating mode: Ignition
S.04
Heating mode: Burner on
S.05
Heating mode: Pump/fan overrun
S.06
Heating mode: Fan overrun
S.07
Heating mode: Pump overrun
S.08
Heating mode: Remaining anti-cycling time
DHW mode
S.10
Hot water requirement via flow sensor
S.11
DHW mode: Fan start-up
S.13
DHW mode: Ignition
S.14
DHW mode: Burner on
S.15
DHW mode: Pump/fan overrun
S.16
DHW mode: Fan overrun
S.17
DHW mode: Pump overrun
Comfort mode, warm start or hot water handling mode with
actoSTOR
S.20
DHW demand
S.21
DHW mode: Fan start-up
S.22
DHW mode: Pump pre-run
S.23
DHW mode: Ignition
S.24
DHW mode: Burner on
S.25
DHW mode: Pump/fan overrun
S.26
DHW mode: Fan overrun
S.27
DHW mode: Pump overrun
S.28
Hot water burner anti-cycling time
Others
0020209593_01 ecoTEC plus Installation and maintenance instructions
47
Appendix
Status code
Meaning
S.30
Room thermostat (RT) is blocking heating
mode
S.31
Summer mode active or no heat requirement
from eBUS controller
S.32
Waiting period because of fan speed deviation
S.34
Frost protection mode active
S.39
"Burner off contact" has responded (e.g. contact thermostat or condensate pump)
S.40
Comfort protection mode is active: Product
running with limited heating comfort
S.41
Water pressure > 2.8 bar
S.42
Flue non-return flap return signal blocks
burner operation (only in connection with VR
40 accessories) or condensate pump faulty,
heat requirement is blocked
S.46
Comfort protection mode, flame loss at minimum load
S.53
Product is within the waiting period of the
modulation block/operation block function
as a result of low water pressure (flow/return
spread too large)
S.54
Product is within the waiting period of the
operation blocking function as a result of low
water pressure (temperature gradient)
S.57
Waiting period, comfort safety mode
S.58
Modulation limitation due to noise/wind
S.61
Gas family check unsuccessful: The coding
resistance on the PCB does not match the
entered gas group (see also F.92).
S.62
Gas family check unsuccessful: CO/CO₂ values at limit. Check combustion.
S.63
Gas family check unsuccessful: Combustion
quality outside permissible range (see F.93).
Check combustion.
S.76
System pressure too low. Top up water.
S.96
Return sensor test running, heating demands
are blocked.
S.97
Water pressure sensor test running, heating
demands are blocked.
S.98
Flow/return sensor test running, heating demands are blocked.
D
Overview of fault codes
Code
Meaning
Cause
F.00
Flow temperature sensor interruption
NTC plug not plugged in or has come loose, multiple plug on the PCB
not plugged in correctly, interruption in cable harness, NTC defective
F.01
Return temperature sensor interruption
NTC plug not plugged in or has come loose, multiple plug on the PCB
not plugged in correctly, interruption in cable harness, NTC defective
F.02
Interruption cylinder charging sensor
actoSTOR (NTC) only in combination with
F.91
NTC defective, NTC cable defective, defective plug connection on NTC,
defective plug connection on actoSTOR electronics
F.03
Interruption cylinder sensor actoSTOR
(NTC) only in combination with F.91
NTC defective, NTC cable defective, defective plug connection on NTC,
defective plug connection on actoSTOR electronics
F.10
Flow NTC short circuit
NTC defective, short circuit in cable harness, cable/casing
F.11
Return NTC short circuit
NTC defective, short circuit in cable harness, cable/casing
48
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Code
Meaning
Cause
F.12
Short circuit at cylinder charging sensor
(NTC) only in combination with F.91
NTC defective, short circuit in cable harness, cable/casing
F.13
Product with integrated hot water
generation: Short circuit warm start
sensor/cylinder sensor
Product with integrated hot water generation and actoSTOR: Short circuit cylinder
sensor (NTC) only in combination with F.91
NTC defective, short circuit in cable harness, cable/casing
F.20
Safety switch-off: Temperature limiter
Incorrect earth connection between cable harness and product, flow or
return NTC defective (loose connection), black discharge via ignition
cable, ignition plug or ignition electrode
F.22
Safety switch-off: Low water pressure
No or insufficient water in the product, water pressure sensor defective,
cable to pump or water pressure sensor loose/not connected/defective
F.23
Safety switch-off: Temperature difference
too great
Pump blocked, insufficient pump output, air in product, flow and return
NTC connected the wrong way round
F.24
Safety switch-off: Temperature rise too fast
Pump blocked, insufficient pump output, air in product, system pressure
too low, non-return valve blocked/incorrectly installed
F.25
Safety switch-off: Flue gas temperature too
high
Break in plug connection for optional flue gas safety temperature limiter
(STB), break in cable harness
F.26
Fault: Gas valve without function
Gas valve stepper motor not connected, multiple plug on the PCB not
plugged in correctly, interruption in cable harness, gas valve stepper
motor defective, electronics defective
F.27
Safety switch-off: Flame simulation
Moisture on the electronics, electronics (flame monitor) defective, gas
solenoid valve leaking
F.28
Failure during start-up: Ignition unsuccessful
Gas meter defective or gas pressure monitor has triggered, air in gas,
gas flow pressure too low, thermal isolator device (TAE) has triggered,
condensate duct blocked, incorrect gas restrictor, incorrect spare part
gas valve, fault on the gas valve, multiple plug on PCB incorrectly
plugged in, break in cable harness, ignition system (ignition transformer,
ignition cable, ignition plug, ignition electrode) defective, ionisation
current interrupted (cable, electrode), incorrect earthing of product,
electronics defective
F.29
Failure during operation: Re-ignition unsuccessful
Gas supply temporarily stopped, flue gas recirculation, condensate duct
blocked, defective earthing of product, ignition transformer has spark
failure
F.32
Fan fault
Plug on fan not correctly plugged in, multiple plug on PCB not correctly
plugged in, break in cable harness, fan blocked, Hall sensor defective,
electronics defective
F.42
Coding resistance fault (possible in combination with F.70)
Short circuit/interruption in output range coding resistance (in cable
harness at heat exchanger) or gas group resistor (on PCB)
F.49
Fault: eBUS
Short circuit on eBUS, eBUS overload or two power supplies with different polarities on the eBUS
F.52
Contact fault mass flow sensor/Venturi
The mass flow sensor/Venturi is not connected electrically
–
–
–
–
–
F.53
Combustion regulation fault
The plug is not plugged in correctly
The plug is not plugged in
The plug is defective
The slot is defective (loose connection)
Mass flow sensor/Venturi defective
The combustion regulation has detected a fault
–
–
–
Gas flow pressure too low
Liquid gas coding resistance used when operating with natural gas
If the fault occurs again after being cleared:
–
–
0020209593_01 ecoTEC plus Installation and maintenance instructions
Gas valve defective
Mass flow sensor/Venturi defective, wet or blocked (if the fault
occurs again after being cleared): Do not wet the sensor, do not
use any lubricants on the O-ring on the Venturi.
49
Appendix
Code
Meaning
Cause
F.54
Fault in the gas supply (in combination with
F.28/F.29)
There is insufficient gas supply to operate the unit
Combustion component fault
A component in the combustion regulation is defective
F.56
–
–
–
–
–
–
F.57
End comfort protection mode
F.61
Gas valve actuation fault
Ignition electrode highly corroded
The gas valve cannot be actuated
–
–
–
Gas valve switch-off delay
Contact fault at the gas valve (plug not plugged in correctly or not
plugged in, plug defective, slot is defective (loose connection))
Natural gas coding resistance used when operating with liquid gas
If the fault occurs again after being cleared: The gas valve is defective
Active comfort protection mode has detected a regulation fault
–
F.62
Gas isolator cock(s) closed
Gas flow pressure is too low
Gas valve defective
Cable harness supply line to the gas valve is defective (short to
earth, short circuit)
Gas valve defective
PCB defective
Delayed shutdown of gas valve detected
–
–
–
Secondary light (ignition and monitoring electrode indicates delayed
extinguishing of the flame signal)
Gas valve defective
PCB defective
F.63
Fault: EEPROM
Electronics defective
F.64
Fault: Electronics/NTC
Flow or return NTC short circuited, electronics defective
F.65
Fault: Electronics temp.
Electronics overheating due to external influences, electronics defective
F.67
Fault: Electronics/flame
Implausible flame signal, electronics defective
F.68
Fault: Unstable flame signal
Air in gas, gas flow pressure too low, incorrect air ratio, condensate
duct blocked, incorrect gas restrictor, ionisation flow interruption (cable,
electrode), flue gas recirculation, condensate duct
F.70
Invalid device specific number (DSN)
If spare parts fitted: Display and PCB replaced at same time and DSN
not reset, incorrect or missing output range coding resistance
F.71
Flow NTC fault
Flow temperature sensor signalling constant value:
–
–
Flow temperature sensor incorrectly positioned at supply pipe
Flow temperature sensor defective
F.72
Flow/return NTC fault
Flow/return NTC temperature difference too great → flow and/or return
temperature sensor defective
F.73
Water pressure sensor signal in the wrong
range (too low)
Interruption/short circuit of water pressure sensor, interruption/short
circuit to GND in supply line to water pressure sensor or water pressure
sensor defective
F.74
Water pressure sensor signal outside correct range (too high)
Line to water pressure sensor has a short circuit to 5 V/24 V or internal
fault in the water pressure sensor
F.75
Fault: No pressure change detection when
starting pump
Water pressure sensor and/or pump defective, air in the heating installation, insufficient water in the product; check adjustable bypass, connect
external expansion vessel to the return
F.77
Fault: Flue non-return flap/condensate
pump
No response from flue non-return flap or condensate pump defective
F.78
Interruption to DHW outlet sensor at the
external controller
UK link box is connected, but hot water NTC not bridged
F.80
Interruption or short circuit of secondary
heat exchanger inlet sensor; only in connection with F.91
NTC defective, NTC cable defective, defective plug connection on NTC,
defective plug connection on actoSTOR electronics
Sensor plug has short to earth to the casing, short circuit in cable harness, sensor defective
50
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Code
Meaning
Cause
F.81
actoSTOR charging pump defective; only in
combination with F.91
Cylinder is not fully charged after specified time.
Fault: Flow and/or return temperature
sensor temperature change
When the burner starts, the temperature change registered at the flow
and/or return temperature sensor is non-existent or too small.
F.83
–
–
–
–
–
–
–
–
–
F.84
Check cylinder charging sensor and cylinder sensor
Air in the actoSTOR pump
Inspect cable harness for pump
Check the impeller sensor and/or limiter in the product
Diverter valve defective
Secondary heat exchanger blocked
Pump faulty
Insufficient water in product
Flow or return temperature sensor not in correct position at pipe
Fault: Flow/return temperature sensor temperature difference implausible
Flow and return temperature sensors returning implausible values.
F.85
Fault: Flow and return temperature sensors
incorrectly installed
The flow and/or return temperature sensors have been installed on the
same pipe/incorrect pipe
F.90
Communication with actoSTOR module
interrupted
Check cable harness from product to actoSTOR module (PEBus).
If the product is to be operated without an actoSTOR module, set
D.092 = 0.
F.91
Sensor/actuator fault on actoSTOR module
F.92
Coding resistance fault
The coding resistance on the PCB does not match the entered gas
group: Check the resistance, repeat the gas family check and enter the
correct gas group.
F.93
Poor combustion quality
Combustion regulation has detected poor combustion quality
–
–
–
–
–
Flow and return temperature sensors have been inverted
Flow and return temperature sensors have not been correctly installed
Incorrect gas restrictor has been installed for the gas family (another
gas family is present)
Recirculation
Mass flow sensor/Venturi defective (wet, blocked): Do not wet the
sensor, do not use any lubricants on the O-ring on the Venturi.
LED
actoSTOR
module
actoSTOR electronics status
LED on: Communication OK
LED flashing: Communication not OK
LED off: No power supply
Communication
fault
No communication with the PCB
Communication fault between display and PCB in the electronics box
0020209593_01 ecoTEC plus Installation and maintenance instructions
51
Appendix
E
Connection diagrams
Connection diagram, product with integrated hot water generation, ≥ 37 kW
E.1
X22
4
2
X25
8
7
2
1
5
3
11
10
3
1
2
3
4
5
6
4
4
9
6
12
X41
5
1
2
3
4
5
6
6
2
15
12
13
7
8
8
X20
9
7
5
1 +24V
2 Hallsignal
17
3
4
16
X51
X100
X51
Burner Off RT 24V
2
11
12
BUS
13
X40 X51
18
7
17
8
X31
X20
X35
X2
X22
X30
14
13
11
14
M
1
3
4
15
16
1
2
3
17
4
12
X25
B.off
X24
Fuse
X101
3
17
X16
L
N
X11
L
N
X18
L
N
19
24V
230V~
3
2
1
3
2
1
20
10
CH Pump
X18
T2
X24
Fan
X11
Opt
X16
BUS
X100
24V
RT
X2
18
1
5
230V~
1
1
3
4
6
3
2
6
X41
X90
10
4 PWM
5 Masse
21
X1
*
RT
L
N
X12
1
2
22
1
52
Main PCB
2
Operator control panel PCB
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
3
Gas valve
13
Bus connection (digital room thermostat/controller)
4
Mass flow sensor
14
Diverter valve
5
15
Water pressure sensor
6
Outside temperature sensor, flow temperature
sensor (optional, external), DCF receiver
Circulation pump remote control
16
Impeller sensor
7
Power coding resistor
17
Warm start sensor
8
Return temperature sensor
18
Hot water sensor
9
Flow temperature sensor
19
Gas group coding resistor
10
Fan
20
Auxiliary relay (select via D.026)
11
Contact thermostat/burner off
21
Internal pump
12
24 V DC room thermostat
22
Ignition electrode
*
Depending on product type
Inspection and maintenance work – Overview
F
The table below lists the manufacturer requirements with respect to minimum inspection and maintenance intervals. If national regulations and directives require shorter inspection and maintenance intervals, you should observe these instead of
the intervals listed in the table.
No.
Work
Inspection
(annual)
Maintenance
(must be
carried out
at regular
intervals)
1
Check the air/flue pipe for leak-tightness and to ensure that it is fastened correctly. Make sure
that it is not blocked or damaged and has been installed in accordance with the relevant Installation Manual.
X
X
2
Check the general condition of the product. Remove dirt from the product and from the vacuum
chamber.
X
X
3
Visually inspect the general condition of the Thermoblock. In doing so, pay particular attention
to signs of corrosion, rust and other defects. If you notice any damage, carry out maintenance
work.
X
X
4
Check the gas flow pressure at maximum heat input. If the gas flow pressure is not within the
correct range, carry out maintenance work.
X
X
5
Check the CO₂ content (the air ratio) of the product and, if necessary, adjust it. Keep a record of
this.
X
X
6
Disconnect the product from the power mains. Check that the electrical plug connections and
other connections are seated correctly and correct these if necessary.
X
X
7
Close the gas isolator cock and the service valves.
X
8
Drain the product on the water side (observe the pressure gauge). Check the pre-charge pressure of the expansion vessel, and top up the vessel if necessary (approx. 0.03 MPa/0.3 bar under the system filling pressure).
X
9
Check the pre-charge pressure in the shift-load cylinder expansion vessel. Correct the pressure,
if necessary.
10
Remove the compact thermal module.
X
11
Check the insulating mats in the combustion area. If you notice any damage, replace the insulating mats. Replace the burner flange seal each time it is opened and accordingly each time
maintenance work is carried out.
X
12
Clean the heat exchanger.
X
13
Check the burner for damage and replace it if necessary.
X
14
Check the condensate trap in the product, clean and fill this, if required.
15
Install the compact thermal module. Caution: Replace the seals.
X
16
If the volume of water is insufficient or the outlet temperature is not reached, replace the secondary heat exchanger if necessary.
X
17
Clean the filter in the cold water inlet. Replace the filter if impurities can no longer be removed
or if the filter is damaged. In this case, also check the impeller sensor for dirt and damage, clean
the sensor (do not use compressed air for this) and replace the sensor if it is damaged.
X
18
Open the gas isolator cock, reconnect the product to the power mains and switch the product on.
0020209593_01 ecoTEC plus Installation and maintenance instructions
X
X
X
X
X
X
53
Appendix
Inspection
(annual)
No.
Work
19
Open the service valves, fill up the product/heating installation to 0.1-0.2 MPa/1.0-2.0 bar (depending on the static height of the heating installation) and start the purging programme P.00.
20
Perform a test operation of the product and heating installation, including hot water generation,
and purge the system once more if necessary.
21
Perform the gas family check.
22
Visually inspect the ignition and burner behaviour.
23
Check the CO₂ content (the air ratio) of the product again.
24
25
54
Maintenance
(must be
carried out
at regular
intervals)
X
X
X
X
X
X
Check the product for gas, flue gas, hot water and condensate leaks, and repair if necessary.
X
X
Record the inspection/maintenance work carried out.
X
X
X
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
G
Commissioning Checklist
Benchmark Commissioning and
Servicing Section
It is a requirement that the boiler is installed and commissioned to the
completed in full.
www.centralheating.co.uk
© Heating and Hotwater Industry Council (HHIC)
0020209593_01 ecoTEC plus Installation and maintenance instructions
55
Appendix
GAS BOILER SYSTEM COMMISSIONING CHECKLIST
This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating
compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference.
CONTROLS
Optimum start control
Fitted
Fitted
Fitted
Fitted
ALL SYSTEMS
Yes
Yes
CENTRAL HEATING MODE
OR
mbar
OR
mbar
COMBINATION BOILERS ONLY
Yes
Yes
DOMESTIC HOT WATER MODE
OR
mbar OR
mbar
Yes
Temperature
CONDENSING BOILERS ONLY
Yes
ALL INSTALLATIONS
AND
²
Ratio
AND
²
Ratio
Yes
Yes
Yes
Yes
56
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
SERVICE RECORD
It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed.
Service Provider
SERVICE 01
SERVICE 02
AND
AND
²%
²%
SERVICE 03
AND
AND
²%
²%
SERVICE 04
AND
AND
²%
²%
SERVICE 05
AND
AND
²%
²%
SERVICE 06
AND
AND
²%
²%
SERVICE 07
AND
AND
²%
²%
SERVICE 08
AND
AND
²%
²%
SERVICE 09
AND
AND
²%
²%
SERVICE 10
AND
AND
²%
²%
0020209593_01 ecoTEC plus Installation and maintenance instructions
AND
AND
²%
²%
57
Appendix
PRIOR TO CO AND COMBUSTION RATIO CHECK
The boiler manufacturer’s installation instructions should have been followed, gas type verified and gas
supply pressure/rate checked as required prior to commissioning.
As part of the installation process, especially where a flue has been fitted by persons other than the
boiler installer, visually check the integrity of the whole flue system to confirm that all components are
correctly assembled, fixed and supported. Check that manufacturer’s max. flue lengths have not been
exceeded and all guidance has been followed (e.g. Gas Safe Technical Bulletin TB008).
The flue gas analyser should be of the correct type, as specified by BS 7967
Prior to its use, the flue gas analyser should have been maintained and calibrated as specified by the
manufacturer. The installer must have the relevant competence for use of the analyser.
Check and zero the analyser IN FRESH AIR as per analyser manufacturer’s instructions.
NOTE
THE AIR GAS RATIO VALVE IS FACTORY
SET AND MUST NOT BE ADJUSTED
DURING COMMISSIONING UNLESS THIS
ACTION IS RECOMMENDED FOLLOWING
CONTACT WITH THE MANUFACTURER.
If any such adjustment is recommended and
further checking of the boiler is required the
installer/service engineer must be competent
to carry out this work and to use the flue gas
analyser accordingly.
If the boiler requires conversion to operate with
a different gas family (e.g. conversion from
natural gas to LPG) separate guidance will be
provided by the boiler manufacturer
SET BOILER TO MAXIMUM RATE
In accordance with boiler instructions, set boiler to operate at max. rate
(full load condition). Allow sufficient time for combustion to stabilise.
NOTE - Do not insert analyser probe during this period to avoid
possible “flooding” of sensor.
CARRY OUT FLUE INTEGRITY CHECK USING ANALYSER
Insert analyser probe into air inlet test point and allow readings to stabilise.
NOTE - where no air inlet test point is provided then a flue integrity check
with the analyser is not possible. The installer should verify that flue
integrity has been visually checked in accordance with the “Prior to
CO and combustion ratio check” box above before proceeding to the
“Check CO and combustion ratio at maximum rate” stage below.
VERIFY FLUE INTEGRITY
Analyser readings indicate that combustion products
and inlet air must be mixing. Further investigation of
the flue is therefore required.
Check that flue components are assembled, fixed
and supported as per boiler/flue manufacturer’s
instructions.
Check that flue and flue terminal are not obstructed.
NO
Is
O2 • 20.6%
and
CO2 < 0.2%
YES
Is
O2 • 20.6%
and
CO2 < 0.2%
YES
NO
TURN OFF APPLIANCE AND CALL
MANUFACTURER’S TECHNICAL HELPLINE
FOR ADVICE.
THE APPLIANCE MUST NOT BE
COMMISSIONED UNTIL PROBLEMS ARE
IDENTIFIED AND RESOLVED.
CHECK CO AND COMBUSTION RATIO AT MAX. RATE
With boiler still set at maximum rate, insert analyser probe into flue gas
sampling point. Allow readings to stabilise before recording.
NOTE - If no flue gas sampling point is present and the correct procedure is
not specified in the manual, consult boiler manufacturer for guidance.
NO
Check all seals around the appliance burner,
internal flue seals, door and case seals.
Rectify where necessary.
Is
CO less than
335ppm
and
CO/CO2 ratio less
than 0.004
Is
CO less than
350ppm and
CO/CO2 ratio
less than 0.004
YES
YES
SET BOILER TO MINIMUM RATE
In accordance with boiler instructions, set boiler to operate at minimum rate (to
minimum load condition). Allow sufficient time for combustion to stabilise.
NOTE - If manufacturer’s instructions do not specify how to set boiler to minimum
rate contact Technical Helpline for advice.
NO
CHECK CO AND COMBUSTION RATIO AT MINIMUM RATE
With boiler still set at minimum rate, insert analyser probe into flue gas sampling
point. Allow readings to stabilise before recording.
NOTE - If no flue gas sampling point is present and the correct procedure is not
specified in the manual, consult boiler manufacturer for guidance.
TURN OFF APPLIANCE AND CALL
MANUFACTURER’S TECHNICAL HELPLINE
FOR ADVICE.
THE APPLIANCE MUST NOT BE
COMMISSIONED UNTIL PROBLEMS ARE
IDENTIFIED AND RESOLVED. IF
COMMISSIONING CANNOT BE FULLY
COMPLETED, THE APPLIANCE MUST BE
DISCONNECTED FROM THE GAS SUPPLY IN
ACCORDANCE WITH THE GSIUR.
NOTE: Check and record CO and combustion ratio
at both max. and min. rate before contacting the
manufacturer.
58
NO
Is
CO less than
350ppm and
CO/CO2 ratio
less than 0.004
YES
BOILER IS OPERATING SATISFACTORILY
no further actions required.
Ensure test points are capped, boiler case is correctly replaced and
all other commissioning procedures are completed.
Complete Benchmark Checklist, recording CO and combustion ratio
readings as required.
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
H
Opening of the flue pipe
P
I
Q
Q
T
Q
S
Q
R
F
Q
D, E
G
O
C
A
I
M
B
L
N
N
H
H
M
J
K
H.1
Positioning of the opening of a fan-supported flue gas pipe
Installation site
Minimum dimensions
A
Directly below an opening, air bricks, opening windows, etc., that can be opened.
300 mm
B
Above an opening, air bricks, opening windows, etc., that can be opened.
300 mm
C
Horizontally to an opening, air bricks, opening windows, etc., that can be opened.
300 mm
D
Below temperature-sensitive building components, e.g. plastic gutters, down pipes or wastewater
pipes
75 mm
E
Below eaves
200 mm
F
Below balconies or car port roofs
200 mm
G
From vertical wastewater pipes or down pipes
150 mm
H
From external or internal corners
200 mm
I
Above floors, roofs or balconies
300 mm
J
From a surface facing a terminal
600 mm
K
From a terminal facing a terminal
1200 mm
L
From an opening in the car port (e.g. door, window) which leads into the dwelling
1200 mm
M
Vertical from a terminal on the same wall
1500 mm
N
Horizontal from a terminal on the same wall
300 mm
O
From the wall on which the terminal has been installed
0 mm
P
From a vertical structure on the roof
N/A
Q
Above the roof area
300 mm
R
Horizontal from adjacent windows on pitched or flat roofs
600 mm
S
Above adjacent windows on pitched or flat roofs
600 mm
T
Below adjacent windows on pitched or flat roofs
2000 mm
0020209593_01 ecoTEC plus Installation and maintenance instructions
59
Appendix
I
Text from BS 5440-1 on fan-supported flue gas pipes
BS 5440–1: It is recommended that the fanned flue gas system terminal is positioned as follows:
–
–
–
At least 2 m from an opening in the building directly opposite, and
So that the combustion products are not discharged directly across a property boundary.
Dimensions D, E, F and G: These clearances may be reduced to 25 mm without affecting the performance of the boiler.
In order to ensure that the condensate vapour plume does not damage adjacent surfaces, the terminal should be extended as shown.
Dimension H: This clearance may be reduced to 25 mm without adversely affecting the performance of the boiler. However, in order to ensure that the condensate vapour plume does not damage adjacent surfaces, a clearance of 300 mm is
preferred. For IE, recommendations are given in the current issue of the IS 813.
–
J
Opening of the flue pipe below eaves and balconies
Balcony/eaves
Gutter
Adequately secured
air/flue gas pipe
K
The flue pipe must
protrude beyond any overhang
Technical data
Technical data – General
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Designated country (designation in accordance
with ISO 3166)
GB (Great
Britain), IE
(Ireland)
Approved unit categories
II2H3P
Gas connection, boiler
side
15 mm
Flow/return heating connections, boiler side
22 mm
Hot and cold water connection, boiler side
G 3/4″
Expansion relief valve
connector (min.)
15 mm
Air/flue gas connection
60/100 mm
Condensate drain pipework (min.)
19 mm
G20 natural gas flow
pressure
2.0 kPa
(20.0 mbar)
G31 propane gas flow
pressure
3.7 kPa
(37.0 mbar)
Gas flow rate at 15 °C
and 1013 mbar (based on
hot water generation, if
applicable), G20
4.2 m³/h
60
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Gas flow rate at 15 °C
and 1013 mbar (based on
hot water generation, if
applicable), G31
3.1 kg/h
Min. flue gas mass rate
(G20)
3.05 g/s
Min. flue gas mass rate
(G31)
5.03 g/s
Max. flue gas mass rate
17.9 g/s
Min. flue gas temperature
40 ℃
Max. flue gas temperature
70 ℃
Approved gas-fired units
C13, C33,
C43, C53
30% efficiency
109 %
NOx class
5
SEDBUK (2005)
A
SEDBUK (2009)
(G20/G31)
89.3 %
Boiler dimension, width
440 mm
Boiler dimension, height
720 mm
Boiler dimension, depth
600 mm
Mounting weight
–
–
Operating weight (with
water)
–
–
Shift-load cylinder capacity
43 kg
VUW
17 kg
VIHCL
51 kg
VUW
32 kg
VIHCL
15 l
Technical data – G20 power/loading G20
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Nominal heat output
range P at 50/30 °C
7.1
… 30.1 kW
Nominal heat output
range P at 80/60 °C
6.4
… 28.6 kW
Maximum heat output for
hot water generation
38.7 kW
Maximum heat input for
hot water generation
39.5 kW
Maximum heat input,
heating side
28.9 kW
Minimum heat input
6.8 kW
Heating adjustment range
6 … 29 kW
0020209593_01 ecoTEC plus Installation and maintenance instructions
61
Appendix
Technical data – Power/loading G31
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Nominal heat output
range P at 50/30 °C
11.5
… 30.1 kW
Nominal heat output
range P at 80/60 °C
10.4
… 28.6 kW
Maximum heat output for
hot water generation
38.7 kW
Maximum heat input for
hot water generation
39.5 kW
Maximum heat input,
heating side
28.9 kW
Minimum heat input
11.1 kW
Technical data – Heating
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Maximum flow temperature
85 ℃
Max. flow temperature
adjustment range (default
setting: 75 °C)
30 … 80 ℃
Permissible total overpressure
0.3 MPa
(3.0 bar)
Minimum pressure for
full operation
0.08 MPa
(0.80 bar)
Expansion vessel capacity
10 l
Circulation water volume
(with reference to
ΔT= 20 K)
1,230 l/h
Approx. condensate rate
(pH value 3.5 to 4.0) in
50/30 °C heating mode
2.9 l/h
Remaining feed head of
pump (at nominal circulation water volume)
0.025 MPa
(0.250 bar)
Technical data – Hot water handling
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Lowest water volume
2.0 l/min
Water volume (at
ΔT = 30 K)
18.5 l/min
Specific water volume D
(ΔT = 30 K)
20.5 l/min
Water volume (at
ΔT = 35 K)
15.9 l/min
Water volume (at
ΔT = 42 K)
13.2 l/min
Permitted overpressure
1.0 MPa
(10.0 bar)
Required connection
pressure
0.035 MPa
(0.350 bar)
Hot water output temperature range
35 … 65 ℃
62
Installation and maintenance instructions ecoTEC plus 0020209593_01
Appendix
Technical data – Electrics
938 (VUI GB
386/5‑5 A)
ecoTEC plus
Electric connection
230 V/50 Hz
Permissible connected
voltage
190 … 253 V
Built-in fuse (slow-blow)
2A
Min. electrical power consumption
55 W
Max. electrical power
consumption
140 W
Standby electrical power
consumption
–
–
2.7 W
VUW
2.0 W
VIHCL
Level of protection
IP X4 D
Test symbol/registration
no.
CE‑
0085CM0320
0020209593_01 ecoTEC plus Installation and maintenance instructions
63
Index
Index
A
Air index setting................................................................... 26
Air/flue pipe ......................................................................... 17
Air/flue pipe, installed ............................................................ 5
Appliance config. ................................................................. 28
Article number ..................................................................... 10
Automatic air vent................................................................ 24
Auxiliary relay ...................................................................... 21
B
Burner anti-cycling time....................................................... 28
Burner anti-cycling time, resetting ....................................... 28
Burner anti-cycling time, setting .......................................... 28
Burner, replacing ................................................................. 30
Bypass valve, setting........................................................... 29
C
Calling up, diagnostics codes ............................................. 28
Calling up, fault memory...................................................... 30
Calling up, installer level...................................................... 20
Carrying out, inspection work .............................................. 36
Carrying out, maintenance work.......................................... 36
CE label ............................................................................... 10
Check programmes ....................................................... 21–22
Checking the burner ............................................................ 38
Checking, burner ................................................................. 38
Checking, CO₂ content ........................................................ 26
Checking, pre-charge pressure for the internal expansion
vessel on the heat generator .............................................. 39
Circulation pump ................................................................. 20
Cleaning, cold water inlet filter ............................................ 38
Cleaning, heat exchanger .................................................. 37
Clearing, fault memory ........................................................ 30
CO₂ content, checking......................................................... 26
CO₂ content, setting ............................................................ 26
Cold water connection......................................................... 15
Cold water inlet filter, cleaning ............................................ 38
Combustion air ...................................................................... 6
Comfort mode...................................................................... 21
Comfort protection mode..................................................... 30
Compact thermal module ...................................................... 6
Compact thermal module, installing .................................... 38
Compact thermal module, removing ................................... 36
Completing, inspection work ............................................... 39
Completing, maintenance work ........................................... 39
Completing, repair work ...................................................... 36
Component test ................................................................... 36
Condensate drain pipework................................................. 16
Condensate siphon ....................................................... 25, 38
Condensate trap............................................................ 25, 38
Connecting, controller ......................................................... 19
Connecting, shift-load cylinder ............................................ 18
Connection dimensions ....................................................... 12
Contact details..................................................................... 21
Controller, connecting ......................................................... 19
Corrosion............................................................................... 6
Corrugated gas pipe.............................................................. 6
D
Decommissioning ................................................................ 40
Decommissioning, temporarily ............................................ 39
Diagnostics codes, calling up .............................................. 28
Discharge pipe, expansion relief valve................................ 16
64
Disposal, packaging ............................................................ 40
Disposing of the packaging ................................................. 40
Documents ............................................................................ 9
Draining, product ................................................................. 39
E
Electricity ............................................................................... 5
Electronics box, closing....................................................... 18
Electronics box, opening ..................................................... 18
Electronics self-test ............................................................. 36
Ending, installation assistant ............................................... 21
F
Fan, replacing...................................................................... 31
Fault codes.................................................................... 30, 48
Fault memory, calling up ..................................................... 30
Fault memory, deleting........................................................ 30
Fault messages ................................................................... 30
Filling ................................................................................... 24
Filling mode ......................................................................... 21
Flexible hose, expansion relief valve on the shift-load
cylinder ................................................................................ 16
Flue gas route ....................................................................... 5
From the delivery point to the installation site ..................... 11
Front casing, closed .............................................................. 5
Frost ...................................................................................... 6
Function menu..................................................................... 36
G
Gas conversion ................................................................... 25
Gas family check, performing.............................................. 21
Gas ratio setting .................................................................. 25
Gas restrictor....................................................................... 32
Gas valve ............................................................................ 31
Gas valve, replacing............................................................ 31
H
Handing over to the operator............................................... 29
Handling .............................................................................. 11
Heat exchanger, cleaning.................................................... 37
Heat exchanger, replacing .................................................. 33
Heating flow......................................................................... 15
Heating partial load ............................................................. 21
Heating return...................................................................... 15
Hot water connection........................................................... 15
Hot water temperature......................................................... 21
I
Identification plate ............................................................... 10
If you smell gas ..................................................................... 4
Impeller sensor...................................................................... 9
Inspection work, carrying out............................................... 36
Inspection work, completing ................................................ 39
Installation assistant, ending ............................................... 21
Installation assistants, restarting ......................................... 21
Installation site................................................................... 5–6
Installer level, calling up ...................................................... 20
Installing, compact thermal module..................................... 38
Installing, unit connection piece with offset ......................... 17
Installing, unit connection piece, 80/125 mm diameter ....... 17
Intended use.......................................................................... 4
Internal expansion vessel on the heat generator,
replacing.............................................................................. 33
Isolator devices ................................................................... 39
L
Language ............................................................................ 21
Leak detection spray ............................................................. 6
Installation and maintenance instructions ecoTEC plus 0020209593_01
Index
Liquid gas ........................................................................ 4, 14
M
Maintenance interval, setting............................................... 29
Maintenance work, carrying out .......................................... 36
Maintenance work, completing............................................ 39
Mass flow sensor, replacing ................................................ 32
Minimum clearance ............................................................. 12
Multi-functional module ....................................................... 21
O
Operating concept ............................................................... 20
P
PCB and display for the heat generator, replacing ............. 35
PCB or display for the heat generator, replacing ................ 35
Performing, gas family check .............................................. 21
Power supply....................................................................... 19
Pre-charge pressure for the internal expansion vessel on
the heat generator, checking............................................... 39
Pre-charge pressure for the shift-load cylinder expansion
vessel, checking .................................................................. 39
Preparing, repair work ......................................................... 30
Pressure gauge ................................................................... 10
Product dimensions............................................................. 12
Product, draining ................................................................. 39
Product, switching off .......................................................... 39
Pump output, setting ........................................................... 29
Pump, remaining feed head ................................................ 29
Purging ................................................................................ 24
R
Remaining feed head, pump ............................................... 29
Removing, compact thermal module................................... 36
Removing, unit connection piece for the air/flue pipe ......... 17
Repair work, completing...................................................... 36
Repair work, preparing ........................................................ 30
Replacing the burner ........................................................... 30
Replacing, fan ..................................................................... 31
Replacing, gas valve ........................................................... 31
Replacing, heat exchanger.................................................. 33
Replacing, internal expansion vessel on the heat
generator ............................................................................. 33
Replacing, mass flow sensor............................................... 32
Replacing, PCB and display for the heat generator ............ 35
Replacing, PCB or display for the heat generator ............... 35
Replacing, shift-load cylinder charging pump ..................... 34
Replacing, shift-load cylinder impeller sensor ..................... 35
Replacing, shift-load cylinder PCB ...................................... 36
Replacing, unit connection piece for the air/flue pipe.......... 17
Replacing, Venturi ............................................................... 32
Resetting, burner anti-cycling time ...................................... 28
S
Safety device......................................................................... 5
Schematic drawing ................................................................ 5
Scope of delivery................................................................. 11
Self-test ............................................................................... 36
Serial number ...................................................................... 10
Service message................................................................. 30
Setting, burner anti-cycling time .......................................... 28
Setting, bypass valve .......................................................... 29
Setting, CO₂ content............................................................ 26
Setting, maintenance interval .............................................. 29
Setting, pump output ........................................................... 29
Shift-load cylinder charging pump, replacing ...................... 34
Shift-load cylinder expansion vessel ................................... 34
Shift-load cylinder impeller sensor, replacing...................... 35
0020209593_01 ecoTEC plus Installation and maintenance instructions
Shift-load cylinder PCB, replacing....................................... 36
Shift-load cylinder, connecting ............................................ 18
Shift-load cylinder/heat generator pipe connections ........... 15
Side section, installing......................................................... 13
Side section, removing ........................................................ 13
Spare parts.......................................................................... 30
Starting, installation assistants ............................................ 21
Status codes.................................................................. 20, 47
Supply of combustion air ....................................................... 5
Switching off ........................................................................ 20
Switching off, product .......................................................... 39
Switching on ........................................................................ 20
T
Target feed temperature...................................................... 21
Telephone number, competent person ............................... 21
Test programmes ................................................................ 21
Tool ....................................................................................... 6
Treating the heating water................................................... 22
U
Unit connection piece for the air/flue pipe, removing .......... 17
Unit connection piece for the air/flue pipe, replacing .......... 17
Unit connection piece with offset, installing......................... 17
Unit connection piece, 80/125 mm diameter, installing ....... 17
Unloading the box ............................................................... 11
V
Venturi ................................................................................. 31
Venturi, replacing ................................................................ 32
Voltage .................................................................................. 5
W
Weight ................................................................................. 13
65
0020209593_01
08.11.2016
Vaillant Ltd.
Nottingham Road
Belper
Derbyshire
DE56 1JT
Telephone 0330 100 3461
Telephone (renewables) 0207 022 0928
Vaillant Service Solutions 0330 100 3461
Spares Technical Enquiries 01773 596615
info@vaillant.co.uk
technicalspares@groupservice.co.uk
www.vaillant.co.uk
© These instructions, or parts thereof, are protected by copyright and may be reproduced or distributed only with
the manufacturer's written consent.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement