Vaillant | ecoTEC pro 24 & 28 | User guide | Vaillant ecoTEC pro 24 & 28 User Guide

Vaillant ecoTEC pro 24 & 28 User Guide
Operating instructions
ecoTEC pro
VUW ..6/5-3
GB, IE
Publisher/manufacturer
Vaillant GmbH
Berghauser Str. 40
D-42859 Remscheid
Tel. +49 21 91 18‑0
Fax +49 21 91 18‑2810
info@vaillant.de
www.vaillant.de
Contents
Contents
1
Safety .................................................................... 3
1.1
Action-related warnings ......................................... 3
1.2
Intended use .......................................................... 3
1.3
General safety information .................................... 3
2
Notes on the documentation .............................. 5
2.1
Observing other applicable documents ................. 5
2.2
Storing documents................................................. 5
2.3
Applicability of the instructions .............................. 5
3
Product description............................................. 5
3.1
Product design....................................................... 5
3.2
Control elements.................................................... 5
3.3
Displayed symbols................................................. 6
3.4
Information on the identification plate.................... 6
3.5
Serial number ........................................................ 6
3.6
CE label ................................................................. 6
3.7
Energy Saving Trust Endorsed Products .............. 6
3.8
Hot Water Association ........................................... 7
3.9
Benchmark............................................................. 7
4
Operation.............................................................. 7
4.1
Operating concept ................................................. 7
4.2
Basic display.......................................................... 7
4.3
Adjustment and display levels ............................... 8
4.4
Cabinet-type casing ............................................... 8
4.5
Opening the isolator devices ................................. 8
4.6
Starting up the product .......................................... 8
4.7
Switching on the product ....................................... 8
4.8
Setting the heating flow temperature..................... 8
4.9
Setting the hot water temperature ......................... 8
4.10
Switching Comfort mode on and off ...................... 9
4.11
Switching off the product's functions ..................... 9
4.12
Guaranteeing the correct filling pressure of the
heating system....................................................... 9
4.13
Protecting the heating installation against frost ..... 9
5
Troubleshooting ................................................ 10
5.1
Detecting and rectifying faults ............................. 10
5.2
Calling up (Live monitor) status codes ................ 10
6
Care and maintenance ...................................... 10
6.1
Maintenance ........................................................ 10
6.2
Caring for the product .......................................... 10
6.3
Reading maintenance messages ........................ 10
6.4
Checking the condensate discharge pipe and
tundish ................................................................. 10
7
Decommissioning.............................................. 10
7.1
Temporarily decommissioning the product.......... 10
7.2
Permanently decommissioning the product......... 10
8
Recycling and disposal..................................... 10
9
Guarantee and customer service..................... 11
9.1
Guarantee............................................................ 11
9.2
Customer service................................................. 11
B
Troubleshooting ................................................ 12
Appendix ............................................................................ 12
A
2
Status codes – Overview .................................. 12
Operating instructions ecoTEC pro 0020244996_01
Safety 1
1
1.1
Safety
Action-related warnings
Classification of action-related warnings
The action-related warnings are classified in
accordance with the severity of the possible
danger using the following warning signs and
signal words:
Warning symbols and signal words
Danger!
Imminent danger to life or risk of
severe personal injury
Danger!
Risk of death from electric shock
Warning.
Risk of minor personal injury
Caution.
Risk of material or environmental
damage
1.2
Intended use
There is a risk of injury or death to the user or
others, or of damage to the product and other
property in the event of improper use or use
for which it is not intended.
The product is intended as a heat generator
for closed heating installations and for hot
water generation.
Intended use includes the following:
– observance of the operating instructions
included for the product and any other
system components
– compliance with all inspection and maintenance conditions listed in the instructions.
This product can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the product in a safe
way and understand the hazards involved.
Children must not play with the product.
Cleaning and user maintenance work must
not be carried out by children unless they are
supervised.
Any other use that is not specified in these
instructions, or use beyond that specified in
0020244996_01 ecoTEC pro Operating instructions
this document shall be considered improper
use. Any direct commercial or industrial use
is also deemed to be improper.
Caution.
Improper use of any kind is prohibited.
1.3
General safety information
1.3.1 Installation by competent persons
only
The installation, inspection, maintenance
and repair of the product, as well as the gas
ratio settings, must only be carried out by a
competent person.
1.3.2 Danger caused by improper
operation
Improper operation may present a danger to
you and others, and cause material damage.
▶ Carefully read the enclosed instructions
and all other applicable documents, particularly the "Safety" section and the warnings.
▶ Only carry out the activities for which instructions are provided in these operating
instructions.
1.3.3 Risk of death from escaping gas
What to do if you smell gas in the building:
▶ Avoid rooms that smell of gas.
▶ If possible, open doors and windows fully
and ensure adequate ventilation.
▶ Do not use naked flames (e.g. lighters,
matches).
▶ Do not smoke.
▶ Do not use any electrical switches, mains
plugs, doorbells, telephones or other communication systems in the building.
▶ If it is safe to do so, close the emergency
control valve or the main isolator.
▶ If possible, close the gas isolator cock on
the product.
▶ Warn other occupants in the building by
yelling or banging on doors or walls.
▶ Leave the building immediately and ensure
that others do not enter the building.
▶ Notify the gas supply company or the National Grid +44 (0) 800 111999 by telephone once you are outside of the building.
3
1 Safety
1.3.4 Risk of death due to blocked or
leaking flue pipework
What to do if you smell flue gas in the property:
▶ Open all accessible doors and windows
fully to provide ventilation.
▶ Switch off the product.
▶ Inform a competent person.
1.3.5 Risk of death due to explosive and
flammable materials
▶ Do not use the product in storage rooms
that contain explosive or flammable substances (such as petrol, paper or paint).
1.3.6 Risk of death due to changes to the
product or the product environment
▶ Never remove, bridge or block the safety
devices.
▶ Do not tamper with any of the safety
devices.
▶ Do not damage or remove any seals on
components.
▶ Do not make any changes:
– The product itself
– to the gas, air, water and electricity supplies
– to the entire flue gas installation
– to the entire condensate drain system
– to the expansion relief valve
– to the drain pipework
– to constructional conditions that may
affect the operational reliability of the
product
▶ Ensure that the supply of combustion air is
always free of fluorine, chlorine, sulphur,
dust, etc.
▶ Ensure that no chemical substances are
stored at the installation site.
1.3.9 Risk of material damage caused by
frost
▶ Ensure that the heating installation always
remains in operation during freezing conditions and that all rooms are sufficiently
heated.
▶ If you cannot ensure the operation, have a
competent person drain the heating installation.
1.3.10 Risk of injury and material damage
due to maintenance and repairs
carried out incorrectly or not
carried out at all
▶ Never attempt to carry out maintenance
work or repairs on your product yourself.
▶ Faults and damage should be immediately
rectified by a competent person.
▶ Adhere to the maintenance intervals specified.
1.3.7 Risk of poisoning caused by
insufficient combustion air supply
Conditions: Open-flued operation
▶ Ensure that there is a sufficient combustion air supply.
1.3.8 Risk of corrosion damage due to
unsuitable combustion and room air
Sprays, solvents, chlorinated cleaning
agents, paint, adhesives, ammonia compounds, dust or similar substances may lead
to corrosion on the product and in the air/flue
pipe.
4
Operating instructions ecoTEC pro 0020244996_01
Notes on the documentation 2
2
2.1
▶
2.2
▶
2.3
Notes on the documentation
3.2
5
Observing other applicable documents
You must observe all operating instructions enclosed with
the system components.
50
Storing documents
Keep this manual and all other applicable documents
safe for future use.
Applicability of the instructions
These instructions apply only to:
4
Product article number
Article number
Gas Council
Number
VUW 246/5-3 (H-GB)
ecoTEC pro 24
0010021836
47-044-88
VUW 286/5-3 (H-GB)
ecoTEC pro 28
0010021837
47-044-89
VUW 286/5-3 (P-GB)
ecoTEC pro 28
0010021838
47-044-90
3
3.1
Control elements
3
2
1
1
On/off button
3
Fault clearance button
2
Built-in controller (accessory)
4
Operating buttons
5
Display
3.2.1
Operator control panel
Product description
1
8
Product design
7
50
2
3
6
4
5
1
2
1
1
Control elements
2
Plate with serial number
on the rear
2
3
0020244996_01 ecoTEC pro Operating instructions
Current heating flow
temperature, filling
pressure of the heating
installation, operating
mode, fault code or
additional information
Current assignment of
the right-hand selection
button
Left- and right-hand
selection buttons
4
5
6
7
8
and
button
Maximum output operation (for chimney
sweeps only)
Access to the menu for
additional information
Current assignment of
the left-hand selection
button
Active operating status
5
3 Product description
3.3
Displayed symbols
Symbol
bar
Meaning
Explanation
Burner operating correctly
Burner on
Current filling pressure of
the heating system
The dashed lines show
the permitted range
–
Hot water generation
active
–
–
–
Heating mode active
–
–
Comfort mode active
–
–
Maintenance required
Permanently on:
Filling pressure in
the permitted range
Flashing: Filling
pressure outside
the permitted range
Permanently on:
Draw-off mode before burner is on
Flashing: Burner on
in draw-off mode
Permanently on:
Heating mode heat
requirement
Flashing: Burner on
in heating mode
Permanently on:
Comfort mode active
Flashing: Comfort
mode active, burner
on
3.4
Burner anti-cycling time
is active
To avoid the need for
frequent switching on
and off (increases the
product's working life).
Fault in the product
Appears instead of the
basic display, may be
an explanatory plain text
display.
Tmax.
Max. flow temperature
ED 92/42
Current efficiency directive fulfilled with
4* rating
V Hz
Mains voltage and mains frequency
W
Max. electrical power consumption
IP
Level of protection
Heating mode
Hot water generation
P
Nominal heat output range
Q
Heat input range
D
Nominal hot water draw-off rate
Bar code with serial number,
7th to 16th digit = product article number
3.5
Serial number
The serial number is located on a plastic plate at the bottom
of the front casing.
3.6
CE label
The CE label shows that the products comply with the basic
requirements of the applicable directives as stated on the
identification plate.
The declaration of conformity can be viewed at the manufacturer's site.
3.7
Energy Saving Trust Endorsed Products
Information on the identification plate
The identification plate is mounted on the underside of the
product in the factory.
Information on the
identification plate
Meaning
Read the instructions.
VUW…
Vaillant gas-fired wall-hung boiler for
heating and hot water generation
..6/5-3
Calorific value power/product generation
equipment
ecoTEC pro
Product description
2H, G20 – 20 mbar
(2.0 kPa)
Gas group and gas connection pressure
as set at the factory
ww/yyyy
Date of manufacture: Week/year
Cat.
Permissible gas categories
Types
Approved gas-fired units
PMS
Permissible total overpressure in heating
mode
PMW
Permissible total overpressure during hot
water generation
6
Meaning
Information on the maintenance message in the
"Live Monitor"
Summer mode active
Heating mode is
switched off
F.XX
Information on the
identification plate
Only the most energy efficient products can carry the
‘Energy Saving Trust Endorsed Product’ brandmark making
it easy for consumers to choose products that have met strict
energy performance criteria.
Available for: Boilers, Heating controls and chemical inhibitors, the Energy Saving Trust endorsed product brandmark
gives consumers confidence that a product will cost less to
run, help lower energy bills and reduce carbon emissions.
About the Energy Saving Trust
Energy Saving Trust is an independent and impartial organisation that provides trusted energy saving advice to empower millions of people to lead affordable, low energy lifestyles. For more information visit energysavingtrust.org.uk
Operating instructions ecoTEC pro 0020244996_01
Operation 4
3.8
Hot Water Association
Vaillant is a full member of the Hot Water Association and
promotes the scheme in association with its cylinder range.
Details are available on the web site www.vaillant.co.uk
4
Operation
4.1
Operating concept
Operator
control
element
Function
–
–
3.9
Benchmark
+
at
the same
time
Vaillant is a licensed member of the Benchmark Scheme
which aims to improve the standards of installation and commissioning of domestic heating and hot water systems in the
UK and to encourage regular servicing to optimise safety, efficiency and performance.
Benchmark is managed and promoted by the Heating
and Hotwater Industry Council. For more information visit
www.benchmark.org.uk.
▶
Please ensure that the installer has fully completed the
Benchmark Checklist on the inside back pages of the
installation instructions supplied with the product and
that you have signed it to say that you have received a
full and clear explanation of its operation. The installer is
legally required to complete a commissioning checklist
as a means of complying with the appropriate Building
Regulations (England and Wales).
All installations must be notified to Local Area Building Control either directly or through a Competent Persons Scheme.
A Building Regulations Compliance Certificate will then be
issued to the customer who should, on receipt, write the Notification Number on the Benchmark Checklist.
This product should be serviced regularly to optimise its
safety, efficiency and performance. The service engineer
should complete the relevant Service Record on the Benchmark Checklist after each service.
The Benchmark Checklist will be required in the event of any
warranty.
or
–
–
Setting the hot water temperature
Cancelling the activation of an operating
mode
Cancelling a change to a set value
Going one selection level higher
–
–
–
–
–
–
Setting the heating flow temperature
Reading the system pressure
Activating the comfort mode
Activating the operating mode
Confirm setting
Going one selection level lower
–
Calling up the menu
–
–
Reducing or increasing the set value
Scrolling through menu entries
The current function of the
the display.
and
buttons is shown in
Adjustable values are always displayed as flashing.
You must always confirm a change to a value. Only then is
the new setting saved. You can press
to cancel a procedure at any time.
4.2
Basic display
50
The basic display shows the current condition of the product.
If you press a selection button, the activated function is displayed in the display.
The functions that are available depend on whether a controller is connected to the product.
You can switch back to the basic display by:
–
–
Pressing
to exit the selection levels
Not pressing any button for longer than 15 minutes.
If there is an error message present, the basic displays
switches to the error message.
0020244996_01 ecoTEC pro Operating instructions
7
4 Operation
4.3
Adjustment and display levels
4.8
The product has two adjustment and display levels.
1.
Setting the heating flow temperature
Press
◁
The end user level contains information and setting options
that you require as the end user.
( ).
The target value of the heating flow temperature
appears on the display.
The installer level is reserved for the competent person. It is
protected by a code. Only competent persons may change
any settings in the installer level.
4.4
Cabinet-type casing
Enclosing the product in cabinet-type casing requires compliance with the applicable design instructions.
If you require cabinet-type casing for your product, consult
a heating specialist company. Never, under any circumstances, enclose the product yourself.
4.5
1.
2.
3.
Ask the competent person who installed the product to
explain to you where these isolator devices are located
and how to handle them.
Open the gas isolator cock fully.
Open the service valves in the heating installation's flow
and return.
▶
▶
Use
or
to set the required heating flow temperature.
Confirm by pressing
.
▶
▶
▶
Set the maximum possible heating flow temperature on
the product.
Confirm by pressing
.
Set the required heating flow temperature on the controller (→ Controller operating instructions).
4.9
Setting the hot water temperature
Danger!
Risk of death from legionella.
Open the cold water stop valve.
4.6
▶
Conditions: No controller connected
Conditions: Controller connected
Opening the isolator devices
Conditions: Product with integrated hot water generation or connected
domestic hot water cylinder
▶
Note
The competent person may have adjusted
the maximum possible temperature.
Legionella multiply at temperatures below
60 °C.
Starting up the product
Only start up the product once the casing has been completely closed.
4.7
▶
Switching on the product
▶
2
50
1.
Press
◁
Have a competent person inform you
about the measures that should be taken
to protect against Legionella in your installation.
Do not set any water temperatures below
60 °C without consulting the competent
person first.
(
).
The set hot water temperature flashes in the display.
Conditions: No controller connected
▶
1
▶
Press the on/off button (1).
◁
The "Basic display" (→ Page 7) (2) appears in the
display.
▶
or
Conditions: Controller connected
▶
▶
▶
8
Change the hot water temperature by pressing
.
Confirm by pressing
.
Use
to set the maximum possible hot water temperature on the product.
Confirm by pressing
.
Set the required hot water temperature on the controller
(→ Controller operating instructions).
Operating instructions ecoTEC pro 0020244996_01
Operation 4
4.10
Switching Comfort mode on and off
1.
Note
Comfort mode immediately supplies hot water at
the required temperature, without you having to
wait for the water to heat up.
Press
◁
2.
twice.
The values for the current filling pressure and for the
minimum and maximum filling pressures appear in
the display.
Check the filling pressure in the display.
1/2
1.
2.
Press
Press
◁
3.
4.
(
(
System pressure: 0.10 … 0.20 MPa (1.00 … 2.00 bar)
The filling pressure is in the intended pressure range.
).
).
Activate or deactivate Comfort mode by pressing
.
Press
to confirm this change.
◁
4.11
2/2
Comf. on or Comf. off are shown flashing in the
display.
Filling pressure: < 0.08 MPa (< 0.80 bar)
▶ Fill the heating installation. (→ Page 9)
or
When you have activated Comfort mode, the symbol appears in the basic display. When you have
deactivated Comfort mode, the " " symbol goes out
in the basic display.
◁
4.12.2 Filling the heating installation
Caution.
Risk of material damage due to heating
water that is extremely calciferous or corrosive or contaminated by chemicals.
Switching off the product's functions
4.11.1 Switching off heating mode (Summer
mode)
1.
2.
3.
The value of the heating flow temperature appears
in the display.
Use the
button to set the heating flow temperature to
Off.
Confirm by pressing
.
◁
◁
4.12
Unsuitable tap water damages the seals
and diaphragms, blocks components in the
product and heating installation through
which the water flows and causes noise.
To switch off heating mode without switching off the hot
water generation, press
( ).
◁
Heating mode is switched off.
The symbol appears in the display.
Guaranteeing the correct filling pressure of
the heating system
4.12.1 Checking the filling pressure of the heating
installation
Note
To ensure that the heating installation operates
smoothly, the filling pressure when the heating
installation is cold must be between 0.10 MPa and
0.20 MPa (1.0 bar and 2.0 bar) or lie between the
two dashed lines in the bar graph display.
If the heating installation extends over several
storeys, a higher filling pressure may be required
for the heating installation. Ask a competent person for details.
In addition, the
one minute.
symbol appears after approx.
If the filling pressure in the heating installation
falls below 0.05 MPa (0.5 bar), then the product
switches off. The display alternates between the
fault message F.22 and the current filling pressure.
If you have topped up the installation with sufficient heating water, the display automatically
disappears after 20 seconds.
▶
1.
Ask a competent person where the filling cock is located.
2. Connect the filling tap to a heating water supply in the
way you were told by the competent person.
3. Open all radiator valves (thermostatic radiator valves) of
the heating installation.
4. Open the heating water supply.
5. Turn the filling cock on slowly and allow water to flow in
until the required filling pressure has been reached.
6. Close the heating water supply.
7. Purge all radiators.
8. Check the filling pressure in the display.
9. Top up with more water if necessary.
10. Close the filling cock.
11. Return to the basic display. (→ Page 7)
4.13
Protecting the heating installation against
frost
4.13.1 Frost protection function
Caution.
Risk of material damage due to frost.
The frost protection function cannot guarantee flow through the entire heating installation, which means that parts of the heating
installation may freeze and therefore become
damaged.
▶
0020244996_01 ecoTEC pro Operating instructions
Only fill the heating installation with suitable heating water.
During a period of frost, ensure that the
heating installation remains in operation
9
5 Troubleshooting
and that all rooms are sufficiently heated,
even when you are away.
Note
To keep the frost protection devices active, you
should switch your product on and off using the
controller, if one is provided.
If the heating flow temperature falls below 5 °C when the
on/off button is on, the product comes into operation and
heats the circulating water to approx. 30 °C on both the heating side and the hot water side (if available).
6.3
Reading maintenance messages
If the symbol is shown in the display, the product requires
maintenance work.
The product is not in fault mode but continues to operate.
▶
▶
Consult a competent person about this.
If the water pressure is flashing at the same time, simply
add more heating water.
6.4
Checking the condensate discharge pipe
and tundish
The condensate discharge pipe and tundish must always be
penetrable.
4.13.2 Draining the heating installation
▶
When the unit is switched off for an extended period, frost
protection can be guaranteed by completely draining the
heating installation and the product.
You must not be able to see or feel any obstructions in the
condensate discharge pipe and tundish.
▶
Consult a competent person about this.
5
Troubleshooting
5.1
▶
▶
Detecting and rectifying faults
If faults occur, proceed in accordance with the table in
the appendix.
Troubleshooting (→ Page 12)
If the fault cannot be eliminated using the specified
measures or if fault messages (F.xx) occur, contact a
competent person.
5.2
▶
6.1
▶
▶
7
Decommissioning
7.1
Temporarily decommissioning the product
Caution.
Risk of material damage due to frost.
The frost protection and monitoring devices
are only active while the unit is connected
to the power mains and switched on via the
on/off button, and when the gas isolator cock
is open.
Press
and
at the same time.
Status codes – Overview (→ Page 12)
The current operating status (status code) is shown
on the display.
Care and maintenance
Maintenance
An annual inspection of the product carried out by a competent person is a prerequisite for ensuring that the product is
permanently ready and safe for operation, reliable, and has a
long working life.
6.2
If you notice a fault, have it eliminated by a competent
person.
Calling up (Live monitor) status codes
◁
6
▶
Regularly check the condensate discharge pipe and tundish for faults and, particularly, for blockages.
Caring for the product
Clean the casing with a damp cloth and a little solventfree soap.
Do not use sprays, scouring agents, detergents, solvents
or cleaning agents that contain chlorine.
▶
▶
▶
Temporarily decommission the product only if no frost is
expected.
Press the on/off button.
◁
▶
7.2
▶
8
▶
Temporarily decommission the product
only if no frost is expected.
The display goes out.
When decommissioning the product for a prolonged
period (e.g. holiday), close the gas isolator cock and also,
for combination products, the cold water stop valve.
Permanently decommissioning the product
Have a competent person permanently decommission
the product.
Recycling and disposal
The competent person who installed your product is responsible for the disposal of the packaging.
If the product is identified with this symbol:
▶
10
In this case, do not dispose of the product with the
household waste.
Operating instructions ecoTEC pro 0020244996_01
Guarantee and customer service 9
▶
Instead, hand in the product to a collection centre for
waste electrical or electronic equipment.
If the product contains batteries that are marked with
this symbol, these batteries may contain substances that are
hazardous to human health and the environment.
▶
9
9.1
–
In this case, dispose of the batteries at a collection point
for batteries.
Guarantee and customer service
Guarantee
One year guarantee for ecoTEC pro appliances
Vaillant undertakes to rectify any manufacturing defect that
occurs within twelve months of the installation date.
–
Registering with us
Registration is simple. Just complete the Guarantee Registration Card and return to Vaillant within 30 days of installation. Your details will then be automatically registered within
the Vaillant scheme.
Note
No receipt will be issued.
–
Immediate help
If your Vaillant boiler develops a fault your first action should
be to contact your installer, as his professional assessment
is needed under the terms of our Guarantee. If you are unable to contact your installer, phone Vaillant Service Solutions:
Telephone: 0330 100 3461
9.2
Customer service
To ensure regular servicing, it is strongly recommended
that arrangements are made for a Maintenance Agreement.
Please contact Vaillant Service Solutions for further details:
Telephone: 0330 100 3461
0020244996_01 ecoTEC pro Operating instructions
11
Appendix
Appendix
Status codes – Overview
A
Status codes that are not listed here can be viewed in the installation instructions.
Status code
Parameter
Meaning
Displays in heating mode
S.00
Heating: No heat demand
Heating: No heat demand
S.02
Heating mode: Pump pre-run
Heating mode: Pump pre-run
S.03
Heating mode: Ignition
Heating mode: Ignition
S.04
Heating mode: Burner on
Heating mode: Burner on
S.06
Heating mode: Fan overrun
Heating mode: Fan overrun
S.07
Heating mode: Pump overrun
Heating mode: Pump overrun
S.08
Heating mode: Anti-cycling time
Heating, remaining anti-cycling time xx mins
Displays in hot water handling mode
S.10
DHW demand
Hot water requirement via flow sensor
S.14
DHW mode: Burner on
DHW mode: Burner on
Displays in Comfort mode with warm start or hot water handling mode with cylinder
S.20
DHW demand
Hot water requirement
S.22
DHW mode: Pump pre-run
DHW mode: Pump pre-run
S.24
DHW mode: Burner on
DHW mode: Burner on
S.31
No heat demand: Summer mode
Summer mode active
S.34
Heating mode: Frost protection
Frost protection mode, frost protection
S.46
Waiting time: Measuring program
Comfort protection mode, flame loss at minimum load
Others
B
Troubleshooting
Fault
Cause
Measure
Product does not start
up:
The gas isolator cock installed on-site and/or the gas
isolator cock on the product is closed.
Open both gas isolator cocks.
–
–
The power supply in the building is disconnected.
Check the fuse in the building. The product
switches on automatically when the power is
restored.
The product is switched off.
Switch on the product (→ "Switching on the
product" section).
The heating flow temperature is set too low or to the
Heating off position, and/or the hot water temperature
is set too low.
Set the heating flow temperature and hot water
temperature (→ "Setting the heating flow temperature" section/→ "Setting the hot water temperature" section).
The system pressure is insufficient.
Low water pressure in the heating installation (fault message: F.22).
Fill the heating installation (→ "Filling the heating
installation" section).
There is air in the heating installation.
Have your competent person purge the heating
installation.
After three unsuccessful attempts to ignite the flame, the
product switches to fault mode (fault message: F.28).
Press the fault clearance key for one second.
The product makes another attempt to ignite the
flame.
If you have been unable to eliminate the ignition
fault after three fault clearance attempts, consult
a competent person.
The external controller is not set correctly.
Set the external controller correctly (→ Controller
operating instructions).
No hot water
Heating remains cold
Hot water generation
functioning correctly;
heating does not start
up.
12
Operating instructions ecoTEC pro 0020244996_01
0020244996_01
0020244996_01
03.08.2017
Supplier
Vaillant Ltd.
Nottingham Road
Belper
Derbyshire
Telephone 0330 100 3461
info@vaillant.co.uk
www.vaillant.co.uk
DE56 1JT
© These instructions, or parts thereof, are protected by copyright and may be reproduced or distributed only with
the manufacturer's written consent.
We reserve the right to make technical changes.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising