DFI | KD330-H110/KD330-Q170 | manual | Dfi KD330-H110/KD330-Q170 Manual

Dfi KD330-H110/KD330-Q170 Manual
KD330-H110/Q170
MicroATX Industrial Motherboard
User’s Manual
A-452-M-2004
1
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2019. All Rights Reserved.
Notice:
Trademarks
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2
Table of Contents
I/O Connectors............................................................................................ 23
SATA (Serial ATA) Connectors....................................................................... 23
Digital I/O Connector................................................................................... 23
Cooling Fan Connectors............................................................................... 24
Power Connectors........................................................................................ 24
Chassis Intrusion Connector......................................................................... 25
Front Panel Connector................................................................................. 25
LAN LED Connector..................................................................................... 26
S/PDIF Connector........................................................................................ 26
SMBus Connector........................................................................................ 27
Standby Power LED..................................................................................... 27
LPC Connector............................................................................................. 28
Expansion Slots........................................................................................... 28
Battery........................................................................................................ 29
Copyright�������������������������������������������������������������������������������������������������������������2
Trademarks ��������������������������������������������������������������������������������������������������������2
FCC and DOC Statement on Class B ����������������������������������������������������� 2
Warranty��������������������������������������������������������������������������������������������������������������4
Static Electricity Precautions����������������������������������������������������������������������4
Chapter 3 - BIOS Setup ��������������������������������������������������������������� 30
Safety Measures ����������������������������������������������������������������������������������������������4
Overview....................................................................................................... 30
Insyde BIOS Setup Utility......................................................................... 31
About the Package �����������������������������������������������������������������������������������������5
Main........................................................................................................... 31
Advanced.................................................................................................... 31
Security....................................................................................................... 44
Boot........................................................................................................... 44
Exit............................................................................................................. 45
Optional Items �������������������������������������������������������������������������������������������������5
Before Using the System Board���������������������������������������������������������������5
Updating the BIOS..................................................................................... 46
Notice: BIOS SPI ROM.............................................................................. 46
Chapter 1 - Introduction �����������������������������������������������������������������������������6
Specifications.................................................................................................6
Features...........................................................................................................7
Chapter 4 - Supported Software ������������������������������������������������ 47
Chapter 5 - RAID (KD330-Q170 Only) �������������������������������������� 54
Chapter 2 - Hardware Installation������������������������������������������������ 9
Chapter 6 - Intel AMT Settings (KD330-Q170 Only) ��������������� 58
Board Layout..................................................................................................9
System Memory.............................................................................................9
Appendix A - Troubleshooting Checklist ������������������������������������ 72
Installing the DIMM Module......................................................................... 10
CPU................................................................................................................. 11
Installing the CPU........................................................................................ 12
Installing the Fan and Heat Sink.................................................................. 14
Jumper Settings.......................................................................................... 15
Clear CMOS Data......................................................................................... 15
Mini PCIe Signal Select (for KD330-Q170 only)............................................. 15
COM1/COM2 RS232/422/485 Select.............................................................. 16
COM1/COM2 RS232/Power Select................................................................. 17
USB Power Select........................................................................................ 17
Rear Panel I/O Ports.................................................................................. 18
PS/2 Keyboad/Mouse Port............................................................................ 18
COM (Serial) Ports....................................................................................... 19
Graphics Interfaces...................................................................................... 20
RJ45 LAN Ports............................................................................................ 21
USB Ports.................................................................................................... 21
Audio.......................................................................................................... 22
3
Warranty
Static Electricity Precautions
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
4
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
•
•
•
•
One
One
One
One
KD330-H110/Q170 motherboard
COM port cable (Length: 300mm, 2 x COM ports)
Serial ATA data cable (Length: 500mm)
I/O shield
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
•
•
•
•
•
•
USB 2.0 port cable (Length: 350/398mm)
USB 3.0 port cable (Length: 320mm)
D-SUB cable (Length: 300mm, 2 DB9)
Serial ATA data cable (Length: 500mm)
Thermal solution (For 35W, Height: 37.3mm)
Thermal solution (For 65W, Height: 72.8mm)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
•
•
•
A CPU
Memory module
Storage devices such as hard disk drive, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1 - Introduction
INTERNAL I/O
Specifications
SYSTEM
GRAPHICS
Processor
6th/7th Generation Intel® Core™/Pentium®/Celeron® LGA 1151 Socket Processors with
TDP up to 65W
1 x RS-232/422/485 (RS-232 with power) (2.54mm pitch)
4 x RS-232 (2.54mm pitch) (default)
4 x RS-232 (2.54mm pitch) (opt., MOQ required))
USB
KD330-H110:
4 x USB 2.0 (2.54mm pitch)
KD330-Q170:
2 x USB 3.0 (2.00mm pitch)
4 x USB 2.0 (2.54mm pitch)
®
Chipset
KD330-H110: Intel H110 Chipset
KD330-Q170: Intel® Q170 Chipset
Memory
KD330-H110:
Two 288-pin DIMM up to 32GB
Dual Channel DDR4 2133/2400MHz
KD330-Q170:
Four 288-pin DIMM up to 64GB
Dual Channel DDR4 2133/2400MHz
Audio
1 x S/PDIF
SATA
KD330-H110:
4 x SATA 3.0 (up to 6Gb/s)
KD330-Q170:
4 x SATA 3.0 (up to 6Gb/s)
RAID 0/1/5/10
1 x 8-bit DIO
BIOS
Insyde SPI 128Mbit
Controller
Intel® HD Gen 9 Graphics
DIO
Feature
OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
LPC
1 x LPC
SMBus
1 x SMBus
Display
Triple
Displays
EXPANSION Interface
1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
WATCHDOG TIMER Output & Interval System Reset, Programmable via Software from 1 to 255 Seconds
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I (DVI-D signal): resolution up to 1920x1200 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
SECURITY
TPM
POWER
Type
ATX
VGA + DVI-I (DVI-D signal) + DP++
Connector
8-pin ATX 12V power
24-pin ATX power
KD330-H110:
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 2)
1 x PCI
KD330-Q170:
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
1 x PCI
1 x Full-size Mini PCIe (USB/PCIe/mSATA, PCIe by default)
1 x Half-size Mini PCIe (opt., MOQ required))
Consumption
KD330-H110:
Typical: i7 65W: 12V @ 1.22A (14.64 Watt)
Max.: i7 65W: 12V @ 6.92A (83.04 Watt)
KD330-Q170:
Typical: i7 65W: 12V @ 1.32A (15.84 Watt)
Max.: i7 65W: 12V @ 7.12A (85.44 Watt)
RTC Battery
CR2032 Coin Cell
OS SUPPORT
AUDIO
Audio
Codec
Realtek ALC888S-VD2-GR
ETHERNET
Controller
KD330-H110:
1 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219V PCIe (10/100/1000Mbps)
KD330-Q170:
1 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps) (only Core i7/i5 supports iAMT)
REAR I/O
Serial
Ethernet
2 x GbE (RJ-45)
USB
4 x USB 3.0
2 x USB 2.0
Serial
1 x RS-232/422/485 (RS-232 with power) (DB-9)
PS/2
1 x PS/2 (mini-DIN-6)
Display
1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
Audio
1 x Line-out
1 x Mic-in
ENVIRONMENT
MECHANICAL
CERTIFICATIONS
6
Infineon TPM2.0/1.2 (opt., MOQ required)
Windows 7 32/64-bit
Window 8.1 64-bit
Windows 10 64-bit
Ubuntu 16.04
Note: 7th Gen CPU SKU ONLY support Windows 10 64-bit & Ubuntu 16.04.
Temperature
Operating: 0 to 60°C
Storage: -40 to 85°C
Humidity
Operating: 5 to 90% RH
Storage: 5 to 90% RH
MTBF
KD330-H110:
392,639 hrs @ 25°C; 227,309 hrs @ 45°C; 144,160 hrs @ 60°C
Calculation Model: Telcordia Issue 2
Environment: GB, GC – Ground Benign, Controlled
KD330-Q170:
382,699 hrs @ 25°C; 218,291 hrs @ 45°C; 136,737 hrs @ 60°C
Calculation Model: Telcordia Issue 2
Environment: GB, GC – Ground Benign, Controlled
Dimensions
microATX Form Factor
244mm (9.6") x 244mm (9.6")
CE, FCC
Features
• Wake-On-LAN
• Watchdog Timer
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Management Event) signal. However, if your system is in the Suspend mode, you can power-on
the system only through an IRQ or DMA interrupt.
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
• DDR4
Important:
The 5V_standby power source of your power supply must support ≥720mA.
DDR4 delivers increased system bandwidth and improves performance at a lower power than
DDR3/DDR2.
• Graphics
• Wake-On-USB
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications. Supports 1 x VGA, 1 x DVI-I
(DVI-D signal) and 1 x DP++ interfaces for display outputs.
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
• PCI Express
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the 5V_standby power source of your power supply must support ≥2A.
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes. The PCI Express architecture also supports high performance graphics infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth.
• Serial ATA
• RTC Timer
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s.
The RTC installed on the system board allows your system to automatically power-on on the
set date and time.
• Gigabit LAN
• ACPI STR
Intel® I211AT PCIe and Intel® I219V PCIe Gigabit LAN controllers support up to 1Gbps data
transmission for KD330-H110. Intel® I211AT PCIe and Intel® I219LM PCIe with iAMT11.0 (only
Core i7/i5 supports iAMT) Gigabit LAN controllers support up to 1Gbps data transmission for
KD330-Q170.
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
• Audio
The Realtek ALC888S-VD2-GR audio codec provides 5.1-channel High Definition audio output.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to go
through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.
• Wake-On-PS/2
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
7
• Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
• USB
The system board supports the USB 3.0. It is capable of running at a maximum transmission
speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s) and
USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces power
consumption, and is backward compatible with USB 2.0. It is a marked improvement in device
transfer speeds between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
8
Chapter 2
Chapter 2 - Hardware Installation
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Board Layout
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
1
2
JP33
1
COM 1 2
RS232/422/485
Select (JP10) 1
6 2
IC
6
5 1
6 2
5
6
5 1
5
COM 1 RS232/Power Select (JP9)
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
System Memory
1
8
PTN3355
3
COM 1 RS232/422/485 Select (JP8)
4
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
5
+12V
Power
LPC
13 TPM (optional)
14
Socket LGA1151
2
12
DVI-I (DVI-D signal)
DP++
Standby
Power LED
LAN 1
USB 1-2
USB 3.0
13
1
11
Intel
I211AT
1
Clear CMOS
Data (JP1)
LAN 1
3
1
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
1
7
SATA 0
5
Buzzer
1
9
2
1
2
Nuvoton
NCT5104D
(optional)
2
9
1
2
1
USB 3.0
USB 5-6
DIO
19
JP35 JP34
iTE
IT8893E
(for KD330-Q170 only)
1
2
11
10
SMBus
5
USB 2.0
USB 9-10 USB 7-8
1
10
1
2
1
1
2
10
1
2
COM 2
9
1
7
SATA 2
1
6
5
2
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
1
9
2
COM
COM
COM
COM
1
2
COM 4
COM 3
2
2
2
2
5 1
5 1
9
7
SATA 3
(JP14)
1
1 9
2
7
SATA 1
Nuvoton
NCT6106D
COM 9
COM 10
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
DDR4_1
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
Intel
9
Standby Power LED
8
PCIe 1 (PCIe x16 )
1
S/PDIF
LAN 1
7
SPI Flash
BIOS
3
1
JP32
Realtek
ALC888S
2
LAN LED
Battery
DDR4_4
(for KD330-Q170 only)
DDR4_3
DDR4_2
(for KD330-Q170 only)
2
Front Panel
Line-out
Mic-in
1
PS/2 KB/MS
1
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 2
LAN 1
USB
3-4
USB 3.0
24
ATX
Power
1
JP31
Important:
When the Standby Power LED lights red, it indicates that there is power on the
system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
1
Features
5
1
2
COM 5
9
1
2
1
3
COM 6
RS232/422/485 Select (JP11)
RS232/422/485 Select (JP12)
RS232/422/485 Select (JP13)
RS232/Power Select (JP14)
•
Two 288-pin DIMM up to 32GB (KD330-H110)
Four 288-pin DIMM up to 64GB (KD330-Q170)
•
Dual Channel DDR4 2133/2400 MHz
9
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Installing the DIMM Module
The system board supports the following memory interface.
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
Single Channel (SC)
Data will be accessed in chunks of 64 bits (8B) from the memory channels.
Dual Channel (DC)
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board.
Single Channel
Dual Channel
DIMMs are on the same channel.
DIMMs in a channel can be identical or
completely different. However, we highly
recommend using identical DIMMs.
Not all slots need to be populated.
4. Push the “ejector tabs” which are at the ends of the socket to the side.
Ejector tab
Ejector tab
DIMMs of the same memory configuration
are on different channels.
5. Note how the module is keyed to the socket.
Notch
Key
10
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
CPU
6. Grasping the module by its edges, position the module above the socket with the “notch”
in the module aligned with the “key” on the socket. The keying mechanism ensures the
module can be plugged into the socket in only one way.
The system board is equipped with a surface mount LGA 1151 socket. This socket is exclusively designed for installing a LGA 1151 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1151 socket comes with a protective
cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If
the cap is missing or the cap and/or contact pins are damaged, contact your dealer
immediately.
2. Make sure to keep the protective cap. RMA requests will be accepted and processed only if the LGA 1151 socket comes with the protective cap.
7. Seat the module vertically, pressing it down firmly until it is completely seated in the
socket.
Protective
cap
8. The ejector tabs at the ends of the socket will automatically snap into the locked position
to hold the module in place.
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
11
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
Lift the load lever up to
the angle shown on the
photo.
2. Disconnect all power cords and cables.
3. Locate the LGA 1151 CPU
socket on the system
board.
Load lever
5. Lifting the load lever will at
the same time lift the load
plate.
Load
plate
PS/2 KB/MS
LAN 1
LAN 1
6. Remove the protective cap
from the CPU socket. The
cap is used to protect the
CPU socket against dust
and harmful particles.
Remove the protective cap
only when you are about
to install the CPU.
Important:
The CPU socket must not come in contact with anything other than the CPU. Avoid
unnecessary exposure. Remove the protective cap only when you are about to install
the CPU.
4. Unlock the socket by pushing the load lever down,
moving it sideways until it
is released from the retention tab; then lift the load
lever up.
Protective cap
Load lever
Retention tab
12
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
7. Insert the CPU into the
socket. The gold triangular
mark on the CPU must
align with the corner of
the CPU socket shown on
the photo.
8. Close the load plate then
push the load lever down.
While closing the load
plate, make sure the front
edge of the load plate
slides under the retention
knob.
9. Hook the load lever under
the retention tab.
Gold triangular mark
Retention knob
Load lever
Retention tab
Alignment key
The CPU’s notch will at
the same time fit into the
socket’s alignment key.
Alignment key
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
13
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Installing the Fan and Heat Sink
4. Rotate each screw that are
diagonally across the heat
sink. Perform the same
procedure for the other
screws.
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system
board.
Note:
A boxed Intel® processor already includes the CPU fan and heat sink assembly. If your
CPU was purchased separately, make sure to only use Intel®-certified fan and heat
sink.
Heat sink
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of the
CPU. The thermal paste is usually supplied when you purchase the fan / heat sink assembly. Do not spread the paste all over the surface. When you later place the heat sink on
top of the CPU, the compound will disperse evenly.
“Unlocked” position
of screw
“Locked” position of
screw
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel the
strip that covers the paste before you place the fan / heat sink on top of the CPU.
2. Place the heat sink on top
of the CPU. The 4 screw
around the heat sink,
which are used to secure
the heat sink onto the system board, must match the
4 mounting holes around
the socket.
3. Orient the heat sink such
that the CPU fan’s cable is
nearest the CPU fan connector.
PS/2 KB/MS
PS/2 KB/MS
5. Connect the CPU fan’s
cable to the CPU fan
connector on the system
board.
Mounting hole
LAN 1
LAN 1
LAN 1
LAN 1
PS/2 KB/MS
CPU fan connector
CPU fan connector
LAN 1
LAN 1
14
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Jumper Settings
Mini PCIe Signal Select (for KD330-Q170 only)
Clear CMOS Data
PS/2 KB/MS
PS/2 KB/MS
LAN 1
1 2 3
1 2 3
LAN 1
LAN 1
JP1
1-2 On:
Normal (default)
1-2 On:
Mini PCIe
(default)
LAN 1
JP6
1 2 3
1 2 3
2-3 On:
Clear CMOS Data
2-3 On:
mSATA
If you encounter the followings,
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
you can reconfigure the system with the default values stored in the ROM BIOS.
JP6 is used to select the Mini PCIe (full-size) signal: Mini PCIe (default) or mSATA.
To load the default values stored in the ROM BIOS, please follow the steps below.
1. Power-off the system and unplug the power cord.
2. Set JP1 pins 2 and 3 to On. Wait for a few seconds and set JP1 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
15
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM1/COM2 RS232/422/485 Select
JP10
(COM 1)
COM 1
JP7 (COM1)/JP11 (COM2)
JP7 (COM 1)
PS/2 KB/MS
JP8
(COM 1)
2 4 6
2 4 6
1 3 5
1-2 On:
RS232 (default)
1 3 5
1 3 5
3-4 On:
RS422 Full Duplex
JP8/JP10 (COM 1)
5-6 On:
RS485
2 4 6
2 4 6
2 4 6
LAN 1
LAN 1
2 4 6
1 3 5
1 3 5
1-3, 2-4 On:
RS232 (default)
3-5, 4-6 On:
RS422 Full Duplex
JP12/JP13 (COM 2)
JP13 (COM 2)
JP12 (COM 2)
1 3 5
2 4 6
2 4 6
1 3 5
1-3, 2-4 On:
RS232 (default)
3-5, 4-6 On:
RS422 Full Duplex
3-5, 4-6 On:
RS485
2 4 6
JP11 (COM 2)
9
1
2
1 3 5
1 3 5
3-5, 4-6 On:
RS485
COM 1/COM 2
COM 2
1 2345
9
JP7/JP8/JP10 (for COM 1) and JP11/JP12/JP13 (for COM 2) are used to configure the COM
ports to RS232, RS422 (Full Duplex) or RS485. When COM 1 RS232/422/485 is selected, JP8
and JP10 must be set in accordance to JP7. When COM 2 RS232/422/485 is selected, JP12
and JP13 must be set in accordance to JP11. The pin functions of the COM ports will vary according to the jumpers’ setting.
1
2
6789
Pin
RS232
RS422 Full Duplex
RS485
1
DCD-
RXD+
DATA+
2
RD
RXD-
DATA-
3
TD
TXD+
N.C.
4
DTR-
TXD-
N.C.
5
GND
GND
GND
6
DSR-
N.C.
N.C.
7
RTS-
N.C.
N.C.
8
CTS-
N.C.
N.C.
9
RI-
N.C.
N.C.
16
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM1/COM2 RS232 Power Select
USB Power Select
JP9 (COM 1)
JP33
PS/2 KB/MS
PS/2 KB/MS
COM 1
1
2
3
1-2 On:
5VDU (default)
LAN 1
JP31
LAN 1
LAN 1
LAN 1
1
2
3
JP32
2-3 On: 5V
9
1
2
COM 2
JP35
JP14 (COM 2)
JP9 (for COM 1) and JP14 (for COM 2) are used to configure Serial COM ports to pure RS232
or RS232 with power. The pin functions of COM 1 and COM 2 will vary according to JP9’s and
JP14’s setting respectively.
The power of the USB connectors’ voltage buses can be configured to either 5VDU or 5V. The
jumpers, i.e. JP31, JP32, JP33, JP34, and JP35 are located as illustrated above and correspond
to each USB port number as listed below.
JP9 (COM 1)
2 4 6
2 4 6
1 3 5
1-3 (RI-), 2-4 (DCD-) On:
RS232 (default)
JP14 (COM 2)
6
4
2
5
3
1
1-3 (RI-), 2-4 (DCD-) On:
RS232 (default)
1 3 5
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
6
4
2
JP34
5
3
1
JP number
USB Port
JP31
USB 1/2 (USB 3.0)
JP32
USB 3/4 (USB 3.0)
JP33
USB 5/6 (USB 2.0)
JP34
USB 7/8/9/10 (USB 2.0)
JP35
USB 5/6 (USB 3.0)
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
17
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Rear Panel I/O Ports
PS/2 Keyboard/Mouse Port
PS/2 Keyboard/Mouse
PS/2 KB/MS
COM 1
DVI-I
(DVI-D signal)
LAN 1
LAN 2
PS/2 KB/MS
Line-out
USB 2.0
Mic-in
LAN 1
VGA
DP++
USB 3.0
LAN 1
The rear panel I/O ports consist of the following:
•
•
•
•
•
•
•
•
•
•
1
2
1
1
1
1
2
4
1
1
PS/2 Keyboard/Mouse port
USB 2.0 ports
Serial COM port
VGA port
DVI-I (DVI-D signal) port
DP++ port
RJ45 LAN ports
USB 3.0 ports
Line-out jack
Mic-in jack
This rear I/O port is used to connect a PS/2 mouse and a PS/2 keyboard. The PS/2 mouse
port uses IRQ12.
Wake-On-PS/2 Keyboard/Mouse
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power-on the system. To use this function:
• BIOS Setting
Configure the wake-up function of PS/2 keyboard/mouse in the Advanced menu (“ACPI Configuration” submenu) of the BIOS. Refer to the chapter 3 for more information.
Important:
The +5V_standby power source of your power supply must support ≥720mA.
18
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM (Serial) Ports
COM 3 to COM 10
COM 1
PS/2 KB/MS
Pin Assignment
1
DCD-
2
RD
3
TD
4
DTR-
5
GND
6
DSR-
7
RTS-
8
CTS-
9
RI-
LAN 1
VGA
COM 1:
RS232/422/485
LAN 1
COM 2:
RS232/422/485
9
Pin
1
2
COM 7/8/9/10 (optional): RS232
9
1
2
COM 3/4/5/6: RS232
9
1
2
The pin functions of COM 1 port will vary according to setting of JP7, JP8, JP9 and JP10. Refer
to “COM1/COM2 RS232/422/485 Select” and “COM1/COM2 RS232/Power Select” in this chapter
for more information.
The pin functions of COM 2 port will vary according to setting of JP11, JP12, JP13 and JP14.
Refer to “COM1/COM2 RS232/422/485 Select” and “COM1/COM2 RS232/Power Select” in this
chapter for more information.
COM 3 to COM 10 are fixed at RS232. The pin functions are listed at right.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
Connecting External Serial Ports
Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket to
an available slot at the rear of the system chassis then insert the serial port cable to the COM
connector. Make sure the colored stripe on the ribbon cable is aligned with pin 1 of the COM
connector.
BIOS Setting
Configure COM 1 to COM 6 in the “SIO NUVOTON6106D” submenu and COM 7 to COM 10
(optional) in the “SIO NCT5104D” submenu of the Advanced menu of the BIOS. Refer to the
chapter 3 for more information.
19
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Graphics Interfaces
Driver Installation
The display ports consist of the following:
•
•
•
Install the graphics driver. Refer to the chapter 4 for more information.
1 VGA port
1 DVI-I (DVI-D signal) port
1 DP++ port
VGA
PS/2 KB/MS
DVI-I (DVI-D signal)
LAN 1
LAN 1
DP++
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
DVI-I (DVI-D Signal) Port
The DVI-I port is used to connect a LCD monitor. This port supports DVI-D signal only. Connect the display device’s cable connector to the DVI-I port. After plugging the cable connector
into the port, gently tighten the cable screws to hold the connector in place.
DP++ Port
The DP++ port which carries both digital audio and video signals is used to connect a LCD
monitor or a digital TV that has the DP++ port.
BIOS Setting
Configure the display devices in the advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to the chapter 3 for more information.
20
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
RJ45 LAN Ports
USB Ports
PS/2 KB/MS
PS/2 KB/MS
USB 6
USB 5
LAN 1
USB 2.0
LAN 2
LAN 1
LAN 1
LAN 1
LAN 2
USB 2
LAN 1
USB 4
USB 1
LAN 1
USB 3
•
•
•
1 Intel® I211AT PCIe
1 Intel® I219V PCIe (KD330-H110)
1 Intel® I219LM PCIe with iAMT11.0 (KD330-Q170)
USB 7-8
9
10
USB 9-10
GND
+Data
-Data
VCC
Features
USB 5-6
USB 3.0
(for KD330-Q170 only)
1
2
N.C.
GND
+Data
-Data
VCC
Over Current Protection
D+
DGND
TX+
TXGND
RX+
RXPWR
D+
DGND
TX+
TXGND
RX+
RXPWR
USB 3.0
USB 2.0
The LAN ports allow the system board to connect to a local area network by means of a
network hub.
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
BIOS Setting
The system board is equipped with 2 onboard USB 2.0 ports (USB 5-6) and 4 onboard USB
3.0 ports (USB 1-2/3-4). The 10-pin connectors allow you to connect 4 additional USB 2.0
ports (USB 7-8/9-10). The 20-pin connector allows you to connect 2 additional USB 3.0 port
(USB 5-6) for KD330-Q170. The additional USB ports may be mounted on a card-edge bracket.
Install the card-edge bracket to an available slot at the rear of the system chassis and then
insert the USB port cables to a connector.
Configure the onboard LAN ports in the Advanced menu (“ACPI Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
Driver Installation
BIOS Setting
Install the LAN drivers. Refer to the chapter 4 for more information.
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to the chapter 3 for more information.
Driver Installation
You may need to install the proper drivers in your system operation to use the USB device.
Refer to your operating system’s manual or documentation for more information.
21
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Audio
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
PS/2 KB/MS
Rear Audio
Line-out
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
Mic-in
LAN 1
LAN 1
Rear Audio
The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
•
Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
•
Mic-in (Pink)
This jack is used to connect an external microphone.
Driver Installation
Install the audio driver. Refer to the chapter 4 for more information.
22
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
I/O Connectors
PS/2 KB/MS
GND
TXP
TXN
GND
RXN
RXP
GND
SATA (Serial ATA) Connectors
Digital I/O Connector
1
PS/2 KB/MS
7
SATA 3.0 6Gb/s
LAN 1
SATA 0
LAN 1
LAN 1
LAN 1
SATA 1
SATA 2
SATA 3
Digital I/O
1
2
19
Features
•
4 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
•
Supports Intel® Smart Response Technology
•
Supports RAID 0, RAID 1, RAID 5, RAID 10 (KD330-Q170)
The 8-bit Digital I/O connector provides powering-on function to external devices that are
connected to these connectors. The pin functions of the 8-bit digital I/O connector are listed
below.
Digital I/O Connector
Pin
Pin Assignment
Pin
Pin Assignment
1
GND
2
+12V
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
3
DIO7
4
+12V
BIOS Setting
5
DIO6
6
GND
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to the chapter 3 for more information.
7
DIO5
8
+5V
9
DIO4
10
+5V
11
DIO3
12
GND
13
DIO2
14
+5VDU
15
DIO1
16
+5VDU
17
DIO0
18
GND
19
GND
23
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Cooling Fan Connectors
Power Connectors
Ground
CPU Fan
PS/2 KB/MS
1
4
PS/2 KB/MS
GND Speed CTRL
+12V
RPM
ATX
Power
GND
+12V
FAN_IN
LAN 1
LAN 1
LAN 1
1
4
1
8
5
+12V
System Fan 1
LAN 1
+12V
Power
3
12 24
+3.3V
+12V
GND
+12V
+5V
+5VSB
+5V
+5V
NC
PWR_OK
GND
GND
+5V
GND
GND
GND
+5V
PS_ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
1
System Fan 2
1
13
Ground
+12V
FAN_IN
3
Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1.
An ATX12V power supply unit has a standard 24-pin ATX main power connector that must be
inserted into the 24-pin connector. The 8-pin +12V power connector enables the delivery of
more +12VDC current to the processor’s Voltage Regulator Module (VRM).
These fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
BIOS Setting
The power connectors from the power supply unit are designed to fit the 24-pin and 8-pin
connectors in only one orientation. Make sure to find the proper orientation before plugging
the connectors.
The Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS will display the current
speed of the cooling fans. Refer to chapter 3 for more information.
The system board requires a minimum of 300 Watt power supply to operate. Your system
configuration (CPU power, amount of memory, add-in cards, peripherals, etc.) may exceed the
minimum power requirement. To ensure that adequate power is provided, we strongly recommend that you use a minimum of 400 Watt (or greater) power supply.
Important:
Insufficient power supplied to the system may result in instability or the add-in boards
and peripherals not functioning properly. Calculating the system’s approximate power
usage is important to ensure that the power supply meets the system’s consumption
requirements.
24
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Chassis Intrusion Connector
Front Panel Connector
PS/2 KB/MS
PS/2 KB/MS
1 2
Front
Panel
LAN 1
PWR-LED
HD-LED
LAN 1
RESET
LAN 1
ATX-SW
LAN 1
11 12
Chassis
Intrusion
1
2
Signal
Ground
HD-LED - Hard Drive LED
This LED will light when the hard drive is being accessed.
RESET - Reset Switch
The board supports the chassis intrusion detection function. Connect the chassis intrusion
sensor cable from the chassis to this connector. When the system’s power is on and a chassis
intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion
occurred, the alarm will sound only when the system restarts.
This switch allows you to reboot without having to power off the system.
PWR-LED - Power/Standby LED
BIOS Setting
When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power
On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To
RAM) state, it will blink every 4 seconds.
Configure the chassis intrusion detection function in the Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS. Refer to the chapter 3 for more informaiton.
ATX-SW - Power Switch
This switch is used to power on or off the system.
Pin Pin Assignment
HD-LED
RESET
3
HDD Power
5
Signal
7
Ground
9
RST Signal
11
N.C.
Pin Pin Assignment
2
LED Power
PWR-LED 4
LED Power
ATX-SW
6
Signal
8
Ground
10
Signal
25
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LAN LED Connector
S/PDIF Connector
PS/2 KB/MS
PS/2 KB/MS
LAN 1
LAN 1
12
LAN LED
LAN 1
LAN 1
78
SPDIF out
+5V
1
The LAN LED connector is used to detect the connection state of RJ45 LAN ports when the
connection is made to an active network via a cable. The pin functions of the LAN LED connector are listed below.
Pin
Pin Assignment
Pin
Ground
SPDIF in
S/PDIF
5
The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis then connect the audio cable to the S/PDIF connector. Make sure pin 1
of the audio cable is aligned with pin 1 of the S/PDIF connector.
Pin Assignment
1
GBE_LED_1000-
2
GBE_LED_100-
3
GBE_LED_LINK_ACT-
4
3V3DU
5
LINK_1000_2
6
LINK_100_2
7
LINK_ACTIVITY_2
8
3V3DU
26
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
SMBus Connector
Standby Power LED
PS/2 KB/MS
PS/2 KB/MS
LAN 1
LAN 1
Standby Power LED
LAN 1
SMB_Alert
SMB_CLK
3V3DU
LAN 1
1
2
SMBus
SMB_Data
GND
5
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
This LED will lit red when the system is in the standby mode. It indicates that there is power
on the system board. Power-off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
27
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LPC Connector
Expansion Slots
PS/2 KB/MS
14 13
PS/2 KB/MS
LPC
LAN 1
2 1
LAN 1
LAN 1
LAN 1
PCI Express x16
PCI
PCI Express x4
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components within the system, which are typically provided by a Super I/O controller. Furthermore,
it can be used to interface firmware hubs, Trusted Platform Module (TPM) devices and embedded controller solutions. Data transfer on the LPC bus is implemented over a 4 bit serialized
data interface, which uses a 33MHz LPC bus clock. For more information about LPC bus refer
to the Intel® Low Pin Count Interface Specification Revision 1.1’. The table below indicates the
pin functions of the LPC connector.
Pin
Pin Assignment
Pin
Mini PCIe (for KD330-Q170 only)
PCI Express x16 Slot
Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into the
PCI Express x16 slot. To install a graphics card into the x16 slot, align the graphics card above
the slot then press it down firmly until it is completely seated in the slot. The retaining clip of
the slot will automatically hold the graphics card in place.
Pin Assignment
1
L_CLK
2
L_AD1
PCI Slot
3
L_RST#
4
L_AD0
5
L_FRAME#
6
3V3
The PCI slot supports expansion cards that comply with PCI specifications. You can install a
PCI expansion card or a customized riser card designed for only 2 PCI slots expansion (for low
profile PCI card only) into the PCI slot.
7
L_AD3
8
GND
PCI Express x4 Slot
9
L_AD2
10
---
11
INT_SERIRQ
12
GND
Install PCI Express cards such as network cards or other cards that comply to the PCI Express
specifications into the PCI Express x4 slot.
13
5VSB
14
5V
Mini PCIe Socket (for KD330-Q170 only)
The full-size Mini PCIe socket supports USB/Mini PCIe/mSATA signals and is used to install a
Mini PCIe card. Mini PCIe and mSATA signals can be switched with a jumper.
28
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Battery
PS/2 KB/MS
LAN 1
LAN 1
Battery
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to local ordinance.
29
Chapter 2 Hardware Installation
www.dfi.com
Chapter 3
Chapter 3 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
+/<F5> (plus key)
Scrolls forward through the values or options of the highlighted field.
-/<F6> (minus key)
Scrolls backward through the values or options of the highlighted field.
Tab
Select a field.
<F1>
Displays general help
<F9>
Optimized defaults
<F10>
Saves and resets the setup program.
<Enter>
Press <Enter> to enter the highlighted submenu.
Entering the BIOS Setup Utility
Scroll Bar
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
Submenu
When “” appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
30
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Project Name
BIOS Version
KD330
B183.07A
Processor Type
CPUID
CPU Speed
CPU Stepping
L1 Data Cache
L1 Instruction Cache
L2 Cache
L3 Cache
Number Of Processors
Microcode Rev
Intel(R) Core(TM) i5-7500T CPU @ 2.70GHz
0x906E9 (KABYLAKE DT HALO)
2700 MHz
09 (KBL B0/S0/M0 Stepping)
32 KB
32 KB
256 KB
6144 KB
4 Core(s) / 4 Thread(s)
0000005E
Total Memory
System Memory Speed
DIMM 0
DIMM 1
DIMM 2
DIMM 3
4096 MB
2400 MHz
4096 MB
[Not Installed]
[Not Installed]
[Not Installed]
PCH Rev / SKU
Intel ME Version / SKU
31 (D1 Stepping) / SKL PCH-H Q170
11.8.50.3399 / CORPORATE
System Time
System Date
[04:59:00]
[04/17/2018]
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
Rev. 5.0
Important:
Setting incorrect field values may cause the system to malfunction.
This is the help for the
hour, minute, second field.
Valid range is from 0 to
23, 0 to 59, 0 to 59. INCREASE/REDUCE: +/-.
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Rev. 5.0
ACPI Configuration Setting
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
Active Management
UEFI Device Manager
SIO NUVOTON6106D
SIO NCT5104D
Console
F5/F6 Change Values
Enter Select  SubMenu
Technology Support
MEBX Configuration
Debug Configuration
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
Redirection
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
System Time
Note:
KD330-H110 does not support Intel Active Management Technology (Intel® AMT) and
MEBX Configuration.
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from 01 to
12. Date displays the date, from 01 to 31. Year displays the year, from 2000 to 2099.
31
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
ACPI Configuration
Note:
Under Dual Boot Type or UEFI Boot Type mode, if Quiet Boot is set to enabled,
BGRT Logo field will appear for configuration. Refer to the Boot menu for more
information.
This section is used to configure the system ACPI parameters.
InsydeH2O Setup Utility
Rev. 5.0
Advanced
ACPI Configuration
Wake on LAN
Wake On PS/2
After G3
Wake On RTC
F1 Help
Esc Exit
<Enabled>
<Disabled>
<Always On>
<Disabled>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
InsydeH2O Setup Utility
Determines the action taken when the system power
is off and a PCI Power
Management Enable wake
up event occurs.
Rev. 5.0
Advanced
Support display logo with
ACPI BGRT table.
ACPI Configuration
Wake on Lan
Wake On PS/2
After G3
BGRT Logo
Wake On RTC
<Enabled>
<Disabled>
<Always On>
<Enabled>
<Disabled>
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Wake on LAN
BGRT Logo
This field is used to enable or disable the LAN signal to wake up the system.
This field is used to enable or disable to support display logo with ACPI BGRT table.
Wake On PS/2
This field is used to enable or disable the PS/2 device to wake up the system.
After G3
This field is to specify what state to go when power is re-applied after a power
failure (G3 state).
Always On
The system working state.
Always Off
Off, except for trickle current to devices such as the power button.
Wake On RTC
Automatically power the system on at a particular time every day from the Real-time
clock battery.
Wake up time
When Wake On RTC is set to enabled, specify the wake up time of the day: <hour>
(00~23), <minute> (00~59), <second> (00~59).
32
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
CPU Configuration
Video Configuration
This section is used to configure the CPU.
This section configures the video settings.
InsydeH2O Setup Utility
InsydeH2O Setup Utility
Rev. 5.0
Advanced
CPU Configuration
Intel Speed Step
Turbo Mode
CPU C States
Hyper-Threading
F1 Help
Esc Exit
<Enabled>
<Enabled>
<Enabled>
<Enabled>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Rev. 5.0
Advanced
Video Configuration
Allows more than two frequency ranges to be supported.
Primary Display
Internal Graphics Device
Boot display
<Auto>
<Auto>
<VGA+DVI>
Primary Display
Auto
IGFX
PEG
PCI
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Initial priority:
AUTO: PEG->PCIe->PCI
->IGFX
IGFX: IGFX->PEG->
PCIe->PCI
PEG: PEG->PCIe->PCI->
IGFX
PCI: PCI->PCIe->PEG->
IGFX
F9 Setup Defaults
F10 Save and Exit
Primary display
Intel Speed Step
Set the initial priority.
This field is used to enable or disable the Intel Enhanced SpeedStep Technology. If
enabled, Turbo Mode will appear for configuration.
Internal Graphics Device
Keep IGFX enabled or disabled based on the setup options.
Turbo Mode
Enable or disable the turbo mode.
Boot display
CPU C States
Set the display device combination.
Enable or disable the CPU Power Management.
Note:
To control "Primary Display" & "Boot Display", first go to "Boot" menu and select
different "Boot Type".
Boot Type : Legacy Boot Type -> Hide Primary Display & Show Boot Display
Boot Type : UEFI Boot Type -> Show Primary Display & Hide Boot Display
Boot Type : Dual Boot Type -> Show Primary Display & Show Boot Display
Hyper-Threading
Enables this field for Windows XP and Linux which are optimized for Hyper-Threading
technology. Select disabled for other OSes not optimized for Hyper-Threading technology. When disabled, only one thread per enabled core is enabled.
33
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
InsydeH2O Setup Utility
Audio Configuration
Rev. 5.0
Advanced
Primary Display
Internal Graphics Device
Boot display
This section is used to configure the audio settings.
Choose display device
combination
Video Configuration
<Auto>
<Auto>
<VGA+DVI>
InsydeH2O Setup Utility
Rev. 5.0
Advanced
Azaliza
Boot display
Control Detection of the
HD-Audio device.
<Enabled>
DVI+DP1
DVI+VGA
DP1+DVI
DP1+VGA
VGA+DVI
VGA+DP1
Disabled = HDA will be
unconditionally disabled
Enabled = HDA will be
unconditionally enabled
Auto = HDA will be enabled if present, disabled
otherwise.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Azaliza
Control the detection of the Azaliza device.
Disabled
HDA will be unconditionally disabled.
Enabled
HDA will be unconditionally enabled.
Auto
HDA will be enabled if present, disabled otherwise.
34
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
SATA Configuration
USB Configuration
This section is designed to select the SATA controller and the type of hard disk drive which are
installed in your system unit.
This section is used to configure the parameters of the USB device.
InsydeH2O Setup Utility
Rev. 5.0
InsydeH2O Setup Utility
Advanced
SATA Controller(s)
SATA Speed
SATA Mode Selection
Serial ATA Port 0
Port 0
Hot Plug
Serial ATA Port 1
Port 1
Hot Plug
Serial ATA Port 2
Port 2
Hot Plug
Serial ATA Port 3
Port 3
Hot Plug
Serial ATA Port 4
Port 4
Hot Plug
F1 Help
Esc Exit
Rev. 5.0
Advanced
<Enabled>
<Auto>
<AHCI>
[Not Installed]
[Not Installed]
[Not Installed]
[Not Installed]
[Not Installed]
↑/↓ Select Item
←/→ Select Item
Enable/Disable SATA
Device.
Legacy USB Support
XHCI Hand-off
<Enabled>
<Disabled>
<Enabled>
<Disabled>
USB keyboard/mouse/storage support under UEFI
and DOS environment. It
will supporting UEFI environment only if set to
UEFI Only
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
SATA Controller(s)
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Legacy USB Support
This field is used to enable or disable Serial ATA devices.
Disabled
SATA Speed
Disable USB keyboard/mouse/storage support under UEFI and DOS environment.
This field is used to select SATA speed generation limit: Auto, Gen1, Gen2 or Gen3.
Enabled
Enable USB keyboard/mouse/storage support under UEFI and DOS environment.
SATA Mode Selection
UEFI Only
The mode selection determines how the SATA controller(s) operates.
Enable USB keyboard/mouse/storage support under UEFI environment.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
RAID Mode (KD330-Q170 only)
This option allows you to create RAID or Intel Matrix Storage configuration on Serial
ATA devices.
XHCI Hand-off
Enable or disable to clear XHCI controller ownership change SMI bit by BIOS.
Serial ATA Port 0, 1, 2, 3, 4 and Hot Plug
These fields are used to enable or disable the serial ATA port and its hot plug. Serial
ATA Port 4 is used to configure mSATA signal of Mini PCIe (for KD330-Q170 only).
35
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
PCI Express Configuration
Mini PCIE (KD330-Q170 only)
This section configures settings relevant to PCI Express root ports.
InsydeH2O Setup Utility
Rev. 5.0
Advanced
InsydeH2O Setup Utility
Rev. 5.0
Advanced
PEG PCI Express Port setting
PCIE 1
PCIE 2
Mini PCIE
Intel
Intel
Mini PCIE
PCIe Speed
Hot Plug
<Enabled>
<AUTO>
<Disabled>
Control the PCI Express
Root Port.
I211AT
I219LM
F1 Help
Esc Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
F9 Setup Defaults
F10 Save and Exit
InsydeH2O Setup Utility
Rev. 5.0
Advanced
<Enabled>
<AUTO>
<Disabled>
PCIE 1
PCIe Speed
Hot Plug
Enable or Disable the Root
Port
Intel I211AT and Intel I219LM (KD330-Q170)/Intel I219V (KD330-H110)
InsydeH2O Setup Utility
Rev. 5.0
Advanced
Intel I211AT
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
<Enabled>
Control the PCI Express
Root Port.
F9 Setup Defaults
F10 Save and Exit
PCIE 1 to 2
This field is used to enable or disable the PCI Express Root Port.
F1 Help
Esc Exit
PCIe Speed
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Select the speed of the PCI Express Root Port: Auto, Gen1, Gen2 or Gen3.
Hot Plug
This field is used to enable or disable the PCI Express Hot Plug.
36
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
ME Configuration
Active Management Technology Support (KD330-Q170 only)
This section configures settings relevant to flash ME region.
The section allows users to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Please refer to Chapter 6 for more information.
InsydeH2O Setup Utility
Rev. 5.0
Advanced
Me Fw Image Re-Flash
InsydeH2O Setup Utility
Enable/disable to flash ME
region
<Disabled>
Rev. 5.0
Advanced
When disabled AMT
BIOS Features are no
longer supported and user
is no longer able to access
MEBx Setup.
Active Management Technology Support
Intel AMT Support
Un-Configure ME
<Enabled>
<Disabled>
Note
This
able
tures
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
:
option does not disManageability Feain FW.
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
Me Fw Image Re-Flash
This field is used to enable or disable the flash ME region.
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Intel AMT Support
This field is used to enable or disable Intel® Active Management Technology BIOS
Extension.
Un-Configure ME
This field is used to enable or disable un-figuring ME without password.
37
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
MEBX Configuration (KD330-Q170 only)
Debug Configuration
This section configures MEBX setting. Please refer to Chapter 6 for more information.
This section configures Debug setting.
InsydeH2O Setup Utility
Rev. 5.0
Advanced
Dynamic EFI DEBUG
F1 Help
Esc Exit
Enable it to output debug
message from COM port.
<Off>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Dynamic EFI DEBUG
This field is used to turn on or off the function to output debug message from COM
port. If set to on, relevant EFI debug information will show up.
InsydeH2O Setup Utility
Rev. 5.0
Advanced
Dynamic EFI DEBUG
EFI debug print level
EFI debug serial port
EFI debug baud rate
F1 Help
Esc Exit
Enable it to output debug
message from COM port.
<On>
[0x80000000]
[0x3F8]
[115200]
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
38
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
UEFI Device Manager
SIO NUVOTON6106D
The section configures UEFI device with option ROM, such as LAN card, etc.
This section configures the system super I/O chip parameters.
InsydeH2O Setup Utility
InsydeH2O Setup Utility
Advanced
SYS Smart Fan Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
CPU Smart Fan Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
SYS Smart Fan 2 Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
COM Port 1
Base I/O Address
Interrupt
RS485 Auto Flow
COM Port 2
Base I/O Address
Interrupt
Device Manager Setting
UEFI Device Manager
UEFI Device Manager
Exit BIOS Setup Utility and launch Device Manager !!
[OK]
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Rev. 5.0
Advanced
Rev. 5.0
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
<3F8>
<IRQ4>
<Disable>
<Enable>
<2F8>
<IRQ3>
Enable/Disable Smart Fan
↓
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
SYS Smart Fan, CPU Smart Fan, SYS Smart Fan 2 Control
Enable or disable the system/CPU smart fan/fan 2.
Boundary 1 to Boundary 4
Set the boundary temperatures that determine the operation of the fan with different
fan speeds accordingly. For example, when the system or the CPU temperature reaches
boundary temperature 1, the system or CPU fan should be turned on and operate at
the designated speed. The range is from 0-127oC.
Fan Speed Count 1 to Fan Speed Count 4
Set the fan speed. The range is from 1-100% (full speed).
39
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Note:
SYS Smart Fan Control, CPU Smart Fan Control, and SYS Smart Fan 2 Control can be
switched to <Disable>. When they are disabled, it will enable "Fix Fan Speed Count".
InsydeH2O Setup Utility
InsydeH2O Setup Utility
Advanced
Fan Speed Count 3
Fan Speed Count 4
SYS Smart Fan 2 Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
COM Port 1
Base I/O Address
Interrupt
RS485 Auto Flow
COM Port 2
Base I/O Address
Interrupt
RS485 Auto Flow
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
COM Port 5
Base I/O Address
Interrupt
COM Port 6
Base I/O Address
Interrupt
WDT
Case Open
PC Health Status
Rev. 5.0
Advanced
SYS Smart Fan Control
Fix Fan Speed Count
CPU Smart Fan Control
Fix Fan Speed Count
SYS Smart Fan 2 Control
Fix Fan Speed Count
COM Port 1
Base I/O Address
Interrupt
RS485 Auto Flow
COM Port 2
Base I/O Address
Interrupt
RS485 Auto Flow
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
COM Port 5
Base I/O Address
Interrupt
COM Port 6
Base I/O Address
Interrupt
WDT
Case Open
PC Health Status
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Disable>
[50]
<Disable>
[50]
<Disable>
[50]
<Enable>
<3F8>
<IRQ4>
<Disable>
<Enable>
<2F8>
<IRQ3>
<Disable>
<Enable>
<3E8>
<IRQ4>
<Enable>
<2E8>
<IRQ3>
<Enable>
<2F0>
<IRQ4>
<Enable>
<2E0>
<IRQ3>
<Disable>
<Disable>
F5/F6 Change Values
Enter Select  SubMenu
Fan Speed set from
1-100%
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
Rev. 5.0
↑
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
<3F8>
<IRQ4>
<Disable>
<Enable>
<2F8>
<IRQ3>
<Disable>
<Enable>
<3E8>
<IRQ4>
<Enable>
<2E8>
<IRQ3>
<Enable>
<2F0>
<IRQ4>
<Enable>
<2E0>
<IRQ3>
<Disable>
<Disable>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
COM Port 1 to COM Port 6
Configure the settings to use the serial port.
Disable No configuration
Enable
User configuration
RS485 Auto Flow
Enable or disable RS485 auto flow.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable
WDT. Input any value between 1 to 255 seconds.
Case Open
Enable or disable the case open detection function.
40
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
PC Health Status
SIO NCT5104D (optional)
This section displays the PC health status.
This section configures the system super I/O chip parameters.
InsydeH2O Setup Utility
Rev. 5.0
InsydeH2O Setup Utility
Advanced
Advanced
Serial Port 1
Base I/O Address
Interrupt
Serial Port 2
Base I/O Address
Interrupt
Serial Port 3
Base I/O Address
Interrupt
Serial Port 4
Base I/O Address
Interrupt
PC Health Status
Voltage
VBAT
VCORE
VDDQ
5V
+12V
3.040 V
0.896 V
1.200 V
4.821 V
12.056 V
Temperature
System (oC/oF)
CPU (oC/oF)
43.5 C/ 110.3 F
42.0 C/ 107.6 F
Fan Speed
SYS FAN
CPU FAN
SYS FAN 2
0 RPM
6026 RPM
0 RPM
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
<Enable>
<2C0>
<IRQ5>
<Enable>
<2C8>
<IRQ5>
<Enable>
<2D0>
<IRQ7>
<Enable>
<2D8>
<IRQ7>
Configure Serial port using
options: [Disable] No Configuration [Enable] User
Configuration
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Serial Port 1 to Serial Port 4 (optional)
Configure the settings to use the serial port.
Disable No configuration
Enable
User configuration
41
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
When Console Serial Redirect is set to enabled, the screen will appear like below:
Console Redirection
This section configures settings relevant to console redirection.
InsydeH2O Setup Utility
Rev. 5.0
Advanced
Console Redirection Setup
InsydeH2O Setup Utility
Rev. 5.0
Console Serial Redirect
Terminal Type
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
COMA
Enable VT-100, 115200, N81
COMB
Disable VT-100, 115200, N81
COMC
Disable VT-100, 115200, N81
COMD
Disable VT-100, 115200, N81
COME
Disable VT-100, 115200, N81
COMF
Disable VT-100, 115200, N81
COMG
Disable VT-100, 115200, N81
COMH
Disable VT-100, 115200, N81
COMI
Disable VT-100, 115200, N81
COMJ
Disable VT-100, 115200, N81
Pci Serial Port 0:22:3
Disable VT-100, 115200, N81
Advanced
Enable Console Redirection Function
Console Redirection Setup
Console Serial Redirect
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Disabled>
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
Console Serial Redirect
This field is used to enable or disable the console serial redirection function.
Enable Console Redirection Function
<Enabled>
<VT_100>
<115200>
<8 Bits>
<None>
<1 Bit>
<None>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Terminal Type
Select terminal type: VT_100, VT_100+, VT_UTF8 or PC_ANSI.
Baud Rate
Select baud rate: 115200, 57600, 38400, 19200, 9600, 4800, 2400 or 1200.
Data Bits
Select data bits: 7 bits or 8 bits.
Parity
Select parity bits: none, even or odd.
Stop Bits
Select stop bits: 1 bit or 2 bits.
Flow Control
Select flow control type: none, RTS/CTS or XON/XOFF.
42
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
When UseGlobalSetting is set to disabled, the screen will appear like below:
COMA to COMJ and Pci Serial Port 0:22:3 (COMG to COMJ are optional)
InsydeH2O Setup Utility
Rev. 5.0
InsydeH2O Setup Utility
Advanced
PortEnable
UseGlobalSetting
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
Rev. 5.0
Advanced
<Enabled>
<Enabled>
F5/F6 Change Values
Enter Select  SubMenu
PortEnable
UseGlobalSetting
Terminal Type
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enabled>
<Disabled>
<VT_100>
<115200>
<8 Bits>
<None>
<1 Bit>
<None>
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
PortEnable
This field is used to enable or disable the COM port to redirect the console.
UseGlobalSetting
This field is to enable or disable to use global setting. When enabled the global setting, setting of the COM port will be the same as those in Console Redirection section.
When disabled the global setting, setting of the COM port can be configured independently in this section.
43
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Security
Boot
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Current TPM Device
TPM State
<Not Detected >
Not Installed
Supervisor Password
Not installed
Main
Rev. 5.0
Advanced
Security
Numlock
Boot Type
Network Stack
PXE Boot capability
USB Boot
Quiet Boot
Install or Change the Password and the length of
password must be greater
than one character.
InsydeH2O Setup Utility
Boot
Exit
<On>
<Dual Boot Type>
<Disabled>
<Disabled>
<Enabled>
<Disabled>
Rev. 5.0
Selects Power-on state for
Numlock
Set Supervisor Password
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Numlock
Set Supervisor Password
Select the power-on state for numlock.
Set the supervisor’s password and the length of the password must be greater than
one character.
Boot Type
Select the boot type. The options are Dual Boot Type, Legacy Boot Type or UEFI Boot
Type.
If you select “Dual Boot Type” or “UEFI Boot Type”, the “Network Stack”, “PXE Boot
capability”, “USB Boot” and “Quiet Boot” will show up.
If you select “Legacy Boot Type”, “PXE Boot to LAN”, “USB Boot” and “Quiet Boot” will
show up.
Note:
If the boot type is set to UEFI, the method for RAID volume creation will be different.
Please refer to Chapter 5 ˗ RAID for more information.
Network Stack
This field is used to enable or disable network stack.
PXE Boot capability
Disabled Suppoort Network Stack
UEFI IPv4/IPv6
Legacy Legacy PXE OPROM only
44
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Exit
PXE Boot to LAN
Disable or enable PXE boot to LAN.
USB Boot
Main
Enable or disable to change USB boot devices boot order.
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Exit system setup and save
your changes.
Exit Saving Changes
Load Optimal Defaults
Discard Changes
Save Setting to file
Quiet Boot
Rev. 5.0
Enable or disable booting in text mode.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Exit Saving Changes
Select Yes and then press <Enter> to exit the system setup and save your changes.
Load Optimal Defaults
Select YES and then press <Enter> to load optimal defaults.
Discard Changes
Select YES and then press <Enter> to exit the system setup without saving your
changes.
Save Setting to file
Select this option to save BIOS configuration settings to a USB flash device.
Restore Setting from file
This field will appear only when a USB flash device is detected. Select this field to
restore setting from the USB flash device.
45
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files.
1. The Intel® Management Engine has already been integrated into this system board. Due to
the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board
and used on another system board of the same model.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
46
Chapter 3 BIOS Setup
www.dfi.com
Chapter 4
Chapter 4 - Supported Software
3. Go through the readme
document for more installation tips then click “Install”.
Install drivers, utilities and software applications that are required to facilitate and enhance the
performance of the system board. You may acquire the software from your sales representatives, from an optional DVD included in the shipment, or from the website download page at
https://www.dfi.com/DownloadCenter.
Intel Chipset Software Installation Utility
The Intel Chipset Software Installation Utility is used for updating Windows® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utility, download “KD330 Chipset Driver” zip file at our website.
4. The step displays the
installing status in the progress.
1. Setup is ready to install the
utility. Click “Next”.
2. Read the license agreement
then click “Accept”.
5. After completing installation, click “Restart Now” to
exit setup.
Restarting the system will
allow the new software
installation to take effect.
47
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Graphics Drivers
3. Go through the readme
document for system requirements and installation
tips then click “Next”.
To install the driver, download “KD330 Graphics Driver” zip file at our website.
1. Setup is now ready to
install the graphics driver.
Click “Next”.
4. Setup is now installing
the driver. Click “Next” to
continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is
enabled. With this enabled, after installing the graphics driver and the system rebooted, the
screen will turn blank for 1 to 2 minutes (while WinSAT is running) before the Windows 10
desktop appears. The “blank screen” period is the time Windows is testing the graphics performance.
We recommend that you skip this process by disabling this function then click “Next”.
2. Read the license agreement
then click “Yes”.
5. Click “Yes, I want to restart
this computer now” then
click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
48
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Audio Drivers
Intel LAN Drivers
To install the driver, download “KD330 Audio Driver” zip file at our website.
To install the driver, download “KD330 LAN Driver” zip file at our website.
1. Setup is ready to install the
driver. Click “Next”.
1. Setup is ready to install the
driver. Click “Next”.
2. Click “Yes, I want to restart
my computer now” then
click “Finish”.
2. Click “I accept the terms
in the license agreement”
then click “Next”.
Restarting the system will
allow the new software
installation to take effect.
3. Select the program features
you want installed then
click “Next”.
49
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Management Engine Interface Drivers
4. Click “Install” to begin the
installation.
To install the driver, download “KD330 MEI Driver” zip file at our website.
1. Setup is ready to install the
driver. Click “Next”.
5. The step displays the
installing status in the progress.
2. Read the license agreement
then tick “I accept the
terms in the License Agreement”. Click “Next”.
6. After completing installation, click “Finish”.
50
Chapter 4 Supported Software
www.dfi.com
Chapter 4
IO Driver
3. Click “Next” to install to
the default folder, or click
“Change” to choose another
destination folder.
To install the driver, download “KD330 SIO Driver” zip file at our website.
1. Setup is ready to install the driver.
Click “Next”.
4. Please wait while the product is being installed.
2. Read the license agreement carefully.
Tick “I accept the terms in the License Agreement” then click “Next”.
5. After completing installation, click “Finish”.
51
Chapter 4 Supported Software
www.dfi.com
Chapter 4
3. Go through the readme document for system requirements and
installation tips then click “Next”.
5. Setup is now installing the
driver.
4. Setup is ready to install the driver.
Click “Next”.
6. Click “Yes, I want to restart
this computer now” then
click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
52
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Rapid Storage Technology
The Intel Rapid Storage Technology is a utility that allows you to monitor the current status
of the SATA drives. It enables enhanced performance and power management for the storage
subsystem.
To install the driver, download “KD330 IRST Driver” zip file at our website. Please refer to
Chapter 5 for more information.
53
Chapter 4 Supported Software
www.dfi.com
Chapter 5
Chapter 5 - RAID (KD330-Q170 Only)
Settings
The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1,
RAID 5 and RAID 10.
To enable the RAID function, the following settings are required.
RAID Levels
1. Connect the Serial ATA drives.
RAID 0 (Striped Disk Array without Fault Tolerance)
2. Enable RAID in the Insyde BIOS.
3. Create a RAID volume.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk
drives. This improves the I/O performance of the drives at different channel; however it is not
fault tolerant. A failed disk will result in data loss in the disk array.
3-1. Create a RAID volume if the boot type is UEFI.
4. Install the Intel Rapid Storage Technology Utility.
RAID 1 (Mirroring Disk Array with Fault Tolerance)
Step 1: Connect the Serial ATA Drives
RAID 1 copies and maintains an identical image of the data from one drive to the other drive.
If a drive fails to function, the disk array management software directs all applications to the
other drive since it contains a complete copy of the drive’s data. This enhances data protection
and increases fault tolerance to the entire system. Use two new drives or an existing drive and
a new drive but the size of the new drive must be the same or larger than the existing drive.
Refer to chapter 2 for details on connecting the Serial ATA drives.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID BIOS utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
RAID 5
RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides
better hard drive performance and more storage capacity.
RAID 10 (Mirroring and Striping)
Step 2: Enable RAID in the Insyde BIOS
RAID 10 is a combination of data striping and data mirroring providing the benefits of both
RAID 0 and RAID 1. Use four new drives or an existing drive and three new drives for this
configuration.
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
2. Go to “Advanced” menu and select the “SATA Configuration” menu.
3. Change the “SATA Mode Selection” to “RAID” mode.
RAID Level
Min. Drives
Protection
Description
RAID 0
2
None
Data striping without redundancy
RAID 1
2
Single Drive Failure
Disk mirroring
RAID 5
3
RAID 10
4
4. Save the changes in the “Exit” menu.
5. Reboot the system.
Block-level data striping with
distributed parity
1 Disk Per Mirrored
Combination of RAID 0 (data striping)
Stripe (not same mirror) and RAID 1 (mirroring)
Single Drive Failure
54
Chapter 5 RAID
www.dfi.com
Chapter 5
Step 3: Create a RAID Volume
Step 3-1: Create a RAID Volume if the boot type is UEFI
1. When the Intel RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
If the boot type is set to UEFI, RAID volume creation will be different. Please use the following
steps to create RAID volumes. To set the boot type, enter the Insyde BIOS and go to “Boot”
>”Boot Type”.
®
2. Select 1: Create RAID Volume and press <Enter>.
3. Create a volume name and press <Enter>.
1. Go to the “Advanced” menu of the Insyde BIOS and select “UEFI Device Manager”.
4. Use the up or down arrow keys to select the RAID level and press <Enter>.
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
5. Use the up or down arrow keys to select the strip size and press <Enter>.
Rev. 5.0
Device Manager Setting
ACPI Configuration
CPU Configuration
6. Select the capacity and press <Enter>. You must select less than one hundred percent of
the available volume space to leave space for the second volume.
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
7. Press <Enter> to create the volume.
ME Configuration
Active Management
8. At the prompt, press <Y> to confirm volume creation.
Technology Support
MEBX Configuration
Debug Configuration
UEFI Device Manager
9. Select 4: Exit and press <Enter>.
SIO
SIO
NUVOTON6106D
NCT5104D
Redirection
Console
10. Press <Y> to confirm exit.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
2. The screen displays all available drives. Select “Create RAID volume” to create a RAID
volume”.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
4. Use the up or down arrow keys to scroll through the list of hard drives and press <Enter>
to select the drive.
5. Press <Enter>.
6. Use the up or down arrow keys to select the strip size and press <Enter>.
7. Enter the volume size and press <Enter>.
8. At the prompt, press <Y> to confirm volume creation.
55
Chapter 5 RAID
www.dfi.com
Chapter 5
Step 4: Install the Intel Rapid Storage Technology Utility
4. Go through the readme
document to view system
requirements and installation information then click
“Next”.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/
or SATA drives. It enables enhanced performance and power management for the storage
subsystem.
1. Download “KD330 IRST Driver” zip file at our website.
2. Setup is ready to install
the utility. Click “Next”.
5. Click “Next” to install to
the default folder or click
“Change to choose another
destination folder”.
3. Read the license agreement and click “I accept
the terms in the License
Agreement”. Then, click
“Next”.
6. Confirm the installation and
click “Next”.
56
Chapter 5 RAID
www.dfi.com
Chapter 5
7. Click “Yes, I want to restart
this computer now” to
complete the installation
and then click “Finish”.
57
Chapter 5 RAID
www.dfi.com
Chapter 6
Chapter 6 - Intel AMT Settings (KD330-Q170 Only)
Overview
Enable Intel® AMT in the Insyde BIOS
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
Intel Active Management Technology (Intel AMT) combines hardware and software solution to
provide maximum system defense and protection to networked systems.
2. In the Advanced menu, select Active Management Technology Support.
®
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Rev. 5.0
AMT Configuration
• Discover
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
USB Configuration
PCI Express Configuration
ME Configuration
Active Management Technology
MEBX Configuration
• Repair
Support
Debug Configuration
UEFI Device Manager
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
SIO
SIO
NUVOTON6106D
NCT5104D
Redirection
Console
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
3. Select Enabled in the Intel AMT Support field.
InsydeH2O Setup Utility
Advanced
When disabled AMT
BIOS Features are no
longer supported and user
is no longer able to access
MEBx Setup.
Active Management Technology Support
Intel AMT Support
Un-Configure ME
Rev. 5.0
Rev. 5.0
<Enabled>
<Disabled>
Note :
This option does not disable Manageability Features in FW.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
58
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
Enable Intel® AMT in the Intel® Management
Engine BIOS Extension (MEBX) Screen
4. In the Exit menu, select Exit Saving Changes then select Yes and press Enter.
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Rev. 5.0
1. After the system reboots, press <Del> to enter the main menu of the Insyde BIOS.
2. In the Advanced menu, select MEBX Configuration.
Exit system setup and save
your changes.
Exit Saving Changes
Load Optimal Defaults
Discard Changes
Save Setting to file
Main
Advanced
Security
InsydeH2O Setup Utility
Boot
Exit
Rev. 5.0
MEBX Configuration Setting
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
Active Management Technology
MEBX Configuration
Support
Debug Configuration
UEFI Device Manager
SIO
SIO
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
NUVOTON6106D
NCT5104D
Redirection
Console
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
3. Select MEBX Configuration and press Enter.
InsydeH2O Setup Utility
Advanced
MEBX Configuration
Rev. 5.0
Rev. 5.0
MEBX Configuration Setting
MEBX Configuration
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
59
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
4. Select MEBx Login and press Enter. You will be prompted for a password. The default
password is “admin”. Enter the default password in the space provided under Intel(R) ME
Password then press Enter.
6. You will be asked to verify the new password. Enter the same new password in the space
provided under Verify Password then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MAIN MENU
MEBx Login
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
MEBx Login
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
Verify password
Intel(R) ME Password
Intel(R) ME Password
[] =Move Highlight
Intel(R) ME Password
[Enter] =Select Entry
[Esc] =Exit
[] =Move Highlight
5. Enter a new password in the space provided under Intel(R) ME New Password then press
Enter. The password must include:
•
•
•
•
•
[Enter] =Select Entry
[Esc] =Exit
7. Select Intel(R) ME General Settings then press Enter.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
MEBx Login
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
Intel(R) ME New Password
Intel(R) ME Password
[] =Move Highlight
[Enter] =Select Entry
[] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
[Esc] =Exit
60
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
8. If you want to change ME password, select Change ME Password then press Enter.
Enter the current password in the space provided under Intel(R) ME Password then press
Enter.
10. You will be asked to verify the new password. Enter the same new password in the space
provided under Verify Password then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
Change ME Password
Local FW Update
<Enabled>
Verify password
Intel(R) ME Password
Intel(R) ME New Password
[] =Move Highlight
<Enabled>
Intel(R) ME New Password
[Enter] =Select Entry
[] =Move Highlight
[Esc] =Exit
[Enter] =Select Entry
[Esc] =Exit
9. Enter a new password in the space provided under Intel(R) ME New Password then press
Enter. The password must include:
•
•
•
•
•
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
11.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) ME PLATFORM CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Change ME Password
Local FW Update
Select Local FW Update then press Enter. Select Enabled or Disabled or Password
Protected then press Enter.
Change ME Password
Local FW Update
<Enabled>
<Enabled>
Disabled
Enabled
Password Protected
Intel(R) ME New Password
Intel(R) ME New Password
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
61
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
12.
Press Esc until you return to the Main Menu. Select Intel(R) AMT Configuration then
press Enter.
In the Intel(R) AMT Configuration menu, select SOL/Storage Redirection/KVM
then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) AMT CONFIGURATION
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[] =Move Highlight
13.
14.
[Enter] =Select Entry
<Anytime>
<Full Unprovision>
[] =Move Highlight [Enter] =Select Entry [Esc] =Exit
[Esc] =Exit
In the Intel(R) AMT Configuration menu, select Manageability Feature Selection
then press Enter. Select Enabled or Disabled then press Enter.
15.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Enabled>
In the SOL/Storage Redirection/KVM menu, select Username and Password then
press Enter. Select Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
<Enabled>
Username and Password
SOL
Storage Redirection
KVM Feature Selection
<Anytime>
<Full Unprovision>
<Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
62
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
16.
Select SOL then press Enter. Select Enabled or Disabled then press Enter.
18.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
Select KVM Feature Selection then press Enter. Select Enabled or Disabled then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
<Enabled>
<Enabled>
<Enabled>
<Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
Disabled
Enabled
Disabled
Enabled
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
17.
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
Select Storage Redirection then press Enter. Select Enabled or Disabled then press
Enter.
19.
Press Esc until you return to the Intel(R) AMT Configuration menu. Select User Consent then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Enabled>
<Enabled>
<Enabled>
<Enabled>
Manageability Feature Selection
> SOL/Storatge Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
<Enabled>
<Anytime>
<Full Unprovision>
[] =Move Highlight [Enter] =Select Entry [Esc] =Exit
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
63
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
20.
In the User Consent menu, select User Opt-in then press Enter. Select NONE or KVM
or ALL then press Enter.
22.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Press Esc until you return to the Intel(R) AMT Configuration menu. Select Password
Policy then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
<KVM>
<Enabled>
Manageability Feature Selection
<Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
NONE
KVM
ALL
During Setup And Configuration
Anytime
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
21.
23.
Select Opt-in Configurable from Remote IT then press Enter. Select Enabled or
Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
In the Intel(R) AMT Configuration menu, select Network Setup then press Enter.
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<KVM>
<Enabled>
Disabled
Enabled
[] =Move Highlight
[Enter] =Select Entry
<Enabled>
<Anytime>
<Full Unprovision>
[Esc] =Exit
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
64
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
24.
26.
In the Intel(R) ME Network Setup menu, select Intel(R) ME Network Name Settings then press Enter.
Select Domain Name then press Enter. Enter the computer’s domain name then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK SETUP
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
> Intel(R) ME Network Name Settings
> TCP/IP Settings
_
_
<Shared>
<Disabled>
Computer Domain Name
[] =Move Highlight
25.
[Enter] =Select Entry
<Enter> =Complete Entry
[Esc] =Exit
27.
In the Intel(R) ME Network Name Settings menu, select Host Name then press
Enter. Enter the computer’s host name then press Enter.
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
_
_
<Shared>
<Disabled>
Dedicated
Shared
Computer Host Name
<Enter> =Complete Entry
Select Shared/Dedicated FQDN then press Enter. Select Shared or Dedicated then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
[Esc] =Discard Changes
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[Esc] =Discard Changes
65
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
28.
30.
Select Dynamic DNS Update then press Enter. Select Enabled or Disabled then press
Enter. If Dynamic DNS Update is set to Enabled, Periodic Update Interval and
TTL fields will show up.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
Select TTL then press Enter. Enter value then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
Periodic Update Interval
TTL
_
_
<Shared>
<Disabled>
Disabled
Enabled
_
_
<Shared>
<Enabled>
1440
900
Value in Seconds
900
<Enter> =Complete Entry [Esc] =Discard Changes
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
29.
31.
Select Periodic Update Interval then press Enter. Enter value then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
TCP/IP SETTINGS
_
_
<Shared>
<Enabled>
1440
900
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
Periodic Update Interval
TTL
Press Esc until you return to the Intel(R) ME Network Setup menu. Select TCP/IP
Settings then press Enter. In the TCP/IP Settings menu, select Wired LAN IPV4
Configuration then press Enter.
> Wired LAN IPV4 Configuration
Value=0 or >=20
1440
<Enter> =Complete Entry [Esc] =Discard Changes
[] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
66
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
32.
In the Wired LAN IPV4 Configuration menu, select DHCP Mode then press Enter.
Select Enabled or Disabled then press Enter. If set to Disabled, IPV4 Address,
Subnet Mask Address, Default Gateway Address, Preferred DNS Address and
Alternate DNS Address will show up.
34.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
Select Subnet Mask Address then press Enter. Enter address then press Enter.
DHCP Mode
IPV4 Address
Subnet Mask Address
Default Gateway Address
Preferred DNS Address
Alternate DNS Address
<Enabled>
<Disabled>
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Disabled
Enabled
Subnet mask (e.g. 255.255.255.0)
0.0.0.0
<Enter> =Complete Entry [Esc] =Discard Changes
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
33.
35.
Select IPV4 Address then press Enter. Enter address then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
IPV4 Address
Subnet Mask Address
Default Gateway Address
Preferred DNS Address
Alternate DNS Address
Select Default Gateway Address then press Enter. Enter address then press Enter.
DHCP Mode
IPV4 Address
Subnet Mask Address
Default Gateway Address
Preferred DNS Address
Alternate DNS Address
<Disabled>
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
<Disabled>
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Default Gateway address
IP address (e.g. 123.123.123.100)
0.0.0.0
0.0.0.0
<Enter> =Complete Entry [Esc] =Discard Changes
<Enter> =Complete Entry [Esc] =Discard Changes
67
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
36.
Select Preferred DNS Address then press Enter. Enter address then press Enter.
38.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
IPV4 Address
Subnet Mask Address
Default Gateway Address
Preferred DNS Address
Alternate DNS Address
<Disabled>
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Manageability Feature Selection
<Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Activates the current network settings
and opens the ME network interface
Continue: (Y/N)
Preferred DNS address
0.0.0.0
[] =Move Highlight [Enter] =Select Entry [Esc] =Exit
<Enter> =Complete Entry [Esc] =Discard Changes
37.
39.
Select Alternate DNS Address then press Enter. Enter address then press Enter.
In the Intel(R) AMT Configuration menu, select Unconfigure Network Access then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
IPV4 Address
Subnet Mask Address
Default Gateway Address
Preferred DNS Address
Alternate DNS Address
Press Esc until you return to the Intel(R) AMT Configuration menu. If you want to
activate the current network settings and open the ME network inferface, select Activate
Network Access, press Enter, then press Y.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
INTEL(R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Disabled>
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Alternate DNS address
<Enabled>
<Anytime>
<Full Unprovision>
Full Unprovision
0.0.0.0
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
<Enter> =Complete Entry [Esc] =Discard Changes
68
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
40.
In the Intel(R) AMT Configuration menu, select Remote Setup And Configuration
then press Enter.
42.
In the Intel(R) Remote Setup And Configuration menu, select Provisioning Record then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
INTEL(R) REMOTE SETUP AND CONFIGURATION
<Enabled>
<Anytime>
_
_
<Full Unprovision>
Provision Record is not present
[ESC] = Exit
[] =Move Highlight
41.
[Enter] =Select Entry
[Esc] =Exit
[] =Move Highlight
43.
In the Intel(R) Remote Setup And Configuration menu, select Current Provisioning Mode then press Enter.
[Enter] =Select Entry
[Esc] =Exit
In the Intel(R) Remote Setup And Configuration menu, select Provisioning
Server IPV4/IPV6 then press Enter. Enter the address then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
INTEL(R) REMOTE SETUP AND CONFIGURATION
_
_
Provisioning Mode: PKI
[] =Move Highlight
[Enter] =Select Entry
_
_
Provisioning server address
[Esc] =Exit
<Enter> =Complete Entry [Esc] =Discard Changes
69
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
44.
In the Intel(R) Remote Setup And Configuration menu, select Provisioning
Server FQDN then press Enter. Enter the FQDN then press Enter.
46.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Press Esc until you return to the Intel(R) Remote Setup And Configuration menu.
Select TLS PKI then press Enter. Select Remote Configuration ** then press Enter.
Select Enabled or Disabled then press Enter.
INTEL(R) REMOTE CONFIGURATION
Remote Configuration **
PKI DNS Suffix
> Manage Hashes
_
_
<Enabled>
_
Disabled
Enabled
Enter FQDN of provisioning server
<Enter> =Complete Entry
45.
[] =Move Highlight
[Esc] =Discard Changes
If you want to activate remote configuration, in the Intel(R) Remote Setup And Configuration menu, select RCFG then press Enter. Select Start Configuration then press
Enter. Press Y to activate.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
47.
<Enter> =Complete Entry
[Esc] =Discard Changes
Select PKI DNS Suffix then press Enter. Enter the PKI DNS Suffix then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) REMOTE CONFIGURATION
INTEL(R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
<Enabled>
_
This will activate Remote Configuration.
Continue: (Y/N)
Enter PKI DNS Suffix
[] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
<Enter> =Complete Entry
[Esc] =Discard Changes
70
Chapter 5 Intel AMT Settings
www.dfi.com
Chapter 6
48.
50.
In the Intel(R) Remote Configuration menu, select Manage Hashes then press
Enter. Select the hash name then press Insert to enter custom hash certificate name,
press Delete to delete hash, press Enter to view hash information, press + to activate or
deactivate hash, and press Esc to exit.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
In the Intel(R) AMT Power Control menu, select Idle Timeout then press Enter.
Enter the timeout value and press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT POWER CONTROL
INTEL(R) REMOTE CONFIGURATION
Hash Name
VeriSign Class 3
VeriSign Class 3
Go Daddy Class 2
Comodo AAA CA
Starfield Class 2
VeriSign Class 3
VeriSign Class 3
VeriSign Class 3
GTE CyberTrust G1
Baltimore Cyber Tr
Cyber Trust Global
Verizon Global Ro
Entrust. net CA (2
Entrust Root CA
VeriSign Universa
Go Daddy Root CA
Entrust Root CA Startfield Root CA
[Ins] =Add New Hash
[] =Move Highlight
49.
Active
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
[Delete] =Delete Hash
[Enter] =View Hash
Default
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Algorithm
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
This configurations are effective only after AMT provisioning has started
Intel(R) AMT ON in Host Sleep States
Idle Timeout
<Desktop: ON in S0, ME Wake in
S3, S4-5>
65535
Timeout Value (1-65535)
65535
<Enter> =Complete Entry [Esc] =Discard Changes
51.
↓
[+] =Activate Hash
[Esc] =Exit
Press Esc until you return to the Intel(R) AMT Configuration menu, select Power
Control then press Enter. In the Intel(R) AMT Power Control menu, select Intel(R)
AMT ON in Host Sleep States then press Enter. Select an option then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT POWER CONTROL
Press Esc until you return to the Main Menu. Select MEBx Exit then press Enter. Press
Y to exit.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
These configurations are effective only after AMT provisioning has started
Intel(R) AMT ON in Host Sleep States <Desktop: ON in S0, ME Wake in
S3, S4-5>
Idle Timeout
65535
Are you sure you want to exit?(Y/N):
Exit
Desktop: ON in S0
Desktop: ON in S0, ME Wake in S3, S4-5
[] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
[] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
71
Chapter 5 Intel AMT Settings
www.dfi.com
Appendix A
Appendix A - Troubleshooting Checklist
The picture seems to be constantly moving.
Troubleshooting Checklist
1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.
This chapter of the manual is designed to help you with problems that you may encounter
with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple
causes.
2. Move away any objects, such as another monitor or fan, that may be creating a magnetic
field around the display.
Some of the most common things to check when you encounter problems while using your
system are listed below.
The screen seems to be constantly wavering.
3. Make sure your video card’s output frequencies are supported by this monitor.
1. The power switch of each peripheral device is turned on.
1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off.
Fluorescent lights adjacent to the monitor may also cause screen wavering.
2. All cables and power cords are tightly connected.
Power Supply
3. The electrical outlet to which your peripheral devices connected is working. Test the outlet
by plugging in a lamp or other electrical device.
When the computer is turned on, nothing happens.
4. The monitor is turned on.
1. Check that one end of the AC power cord is plugged into a live outlet and the other end
properly plugged into the back of the system.
5. The display’s brightness and contrast controls are adjusted properly.
2. Make sure that the voltage selection switch on the back panel is set for the correct type of
voltage you are using.
6. All add-in boards in the expansion slots are seated securely.
3. The power cord may have a “short” or “open”. Inspect the cord and install a new one if
necessary.
7. Any add-in board you have installed is designed for your system and is set up correctly.
Monitor/Display
If the display screen remains dark after the system is turned on:
1. Make sure that the monitor’s power switch is on.
2. Check that one end of the monitor’s power cord is properly attached to the monitor and
the other end is plugged into a working AC outlet. If necessary, try another outlet.
3. Check that the video input cable is properly attached to the monitor and the system’s
display adapter.
4. Adjust the brightness of the display by turning the monitor’s brightness control knob.
72
Appendix A Troubleshooting Checklist
www.dfi.com
Appendix A
Hard Drive
System Board
Hard disk failure.
1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is
loose, power off the system, re-install the card and power up the system.
1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS.
2. Check the jumper settings to ensure that the jumpers are properly set.
2. If the system is configured with two hard drives, make sure the bootable (first) hard drive
is configured as Master and the second hard drive is configured as Slave. The master hard
drive must have an active/bootable partition.
3. Verify that all memory modules are seated securely into the memory sockets.
4. Make sure the memory modules are in the correct locations.
Excessively long formatting period.
5. If the board fails to function, place the board on a flat surface and seat all socketed components. Gently press each component into the socket.
If your hard drive takes an excessively long period of time to format, it is likely a cable connection problem. However, if your hard drive has a large capacity, it will take a longer time to
format.
6. If you made changes to the BIOS settings, re-enter setup and load the BIOS defaults.
Serial Port
The serial device (modem, printer) doesn’t output anything or is outputting garbled
characters.
1. Make sure that the serial device’s power is turned on and that the device is on-line.
2. Verify that the device is plugged into the correct serial port on the rear of the computer.
3. Verify that the attached serial device works by attaching it to a serial port that is working
and configured correctly. If the serial device does not work, either the cable or the serial
device has a problem. If the serial device works, the problem may be due to the onboard
I/O or the address setting.
4. Make sure the COM settings and I/O address are configured correctly.
Keyboard
Nothing happens when a key on the keyboard was pressed.
1. Make sure the keyboard is properly connected.
2. Make sure there are no objects resting on the keyboard and that no keys are pressed during the booting process.
73
Appendix A Troubleshooting Checklist
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising