Dfi KS070-AL Manual
KS070-AL
7” Touch Panel PC
User’s Manual
A-482-M-2002
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2020. All Rights Reserved.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Backlight Power Select............................................................ 17
Panel Power Select................................................................. 17
LCD/Inverter Power Select...................................................... 18
Copyright����������������������������������������������������������������������������2
Trademarks�������������������������������������������������������������������������2
Chapter 5 - Ports and Connectors��������������������������������������19
Top Panel I/O Ports................................................................ 19
Bottom Panel I/O Ports........................................................... 19
FCC and DOC Statement on Class A������������������������������������2
USB Ports.................................................................................................... 20
COM (Serial) Ports....................................................................................... 21
Graphics Interfaces...................................................................................... 22
Audio Output............................................................................................... 22
DC-in Power Connector ............................................................................... 23
RJ45 LAN Ports............................................................................................ 23
About this Manual���������������������������������������������������������������4
Warranty ���������������������������������������������������������������������������4
I/O Connectors....................................................................... 24
Static Electricity Precautions������������������������������������������������4
Serial ATA Connector & Serial ATA Power Connector...................................... 24
USB OTG Connector ................................................................................... 24
LVDS LCD Panel & Inverter Power Connector................................................ 25
Digital I/O Connector................................................................................... 26
Expansion Slots........................................................................................... 26
Front Panel Connector................................................................................. 27
Standby Power LED..................................................................................... 27
Battery........................................................................................................ 28
SMBus Connector ....................................................................................... 28
Safety Measures�����������������������������������������������������������������4
Safety Precautions��������������������������������������������������������������5
About the Package��������������������������������������������������������������5
Chapter 6 - Mounting Options�������������������������������������������29
Chapter 1 - Introduction������������������������������������������������������6
Wall Mount............................................................................. 29
Panel Mount........................................................................... 30
Overview..................................................................................6
Key Features............................................................................6
Specifications............................................................................7
Getting to Know the KS070-AL..................................................8
Mechanical Dimensions.............................................................9
Chapter 7 - BIOS Setup����������������������������������������������������32
Chapter 8 - Supported Software����������������������������������������44
Chapter 2 - Getting Started�����������������������������������������������10
Chapter 3 - Installing Devices��������������������������������������������11
Removing the Chassis Cover.................................................... 12
Installing an M.2 Card............................................................. 13
Chapter 4 - Jumper Settings����������������������������������������������15
Clear CMOS Data.................................................................... 15
LVDS Channel and bpp Select................................................. 15
Auto Power-on Select.............................................................. 16
M.2 Signal Select.................................................................... 16
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
Warranty
1.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damages to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• One 7” Touch Panel PC
• One sheet of poron foam
• One CD disk includes: Drivers and Manual
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
Optional Items
• Dispose of used batteries according to local ordinance.
• VESA mount kit
• Panel mount kit
• Power cord
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview
KS070-AL
Side View
Model Name
KS070-AL
Processor
Intel Atom® Processor E3900 Series, BGA 1296
Intel Atom® x5-E3940 Processor, Quad Core, 2M Cache, 1.6GHz (1.8GHz), 9.5W
Intel® Celeron® Processor N3350, Dual Core, 2M Cache, 1.1GHz (2.4GHz), 6W
LAN
Two LAN ports on the bottom panel
COM
Two COM ports (DB-9) on the top panel
Display
DP++ and VGA ports on the bottom panel
USB
Two USB 2.0 ports (type A) and two USB 3.0 ports (type A)
Audio
Line-out and Mic-in jacks
Top View
Bottom View
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
Processor
Memory
BIOS
Display and Touch
Screen
Graphics
Storage
Expansion
Audio Controller
Ethernet Controller
Top I/O Ports
Bottom I/O Ports
Watchdog Timer
Power
OS Support
(UEFI only)
Intel Atom® Processor E3900 Series, BGA 1296
Intel Atom® x5-E3940 Processor, Quad Core, 2M Cache, 1.6GHz (1.8GHz),
9.5W
Intel® Celeron® Processor N3350, Dual Core, 2M Cache, 1.1GHz (2.4GHz), 6W
One 204-pin SODIMM up to 8GB
Single Channel DDR3L 1866MHz (4GB memory by default)
Insyde SPI 128Mbit (supports UEFI boot only)
• Display: 7” 800x480 TFT LCD panel with capacitive/resistive touch
screen
• Brightness: 500 cd/m²
• Contrast: 400:1
• Backlight Lifetime: 50,000 hours
• Intel® HD Graphics
Display port: VGA (resolution up to 1920x1200 @ 60Hz) & DP++:
resolution up to 4096x2160 @ 60Hz
Supported applications: OpenGL 4.2, DirectX 11.1, OpenCL 1.2,
OpenGL ES 3.0
Supported Codecs:
HW Decode: H.264, MPEG2, VC1, VP8, H.265, MPEG4
HW Encode: H.264, MPEG2, MPEG4
CFast Socket
1 x Full-size Mini PCIe (USB/PCIe)
1 x M.2 2242 B-key (PCIe/USB 2.0/SATA 3.0)
Realtek ALC262
2 x Intel® I211AT PCIe (10/100/1000Mbps)
2 x RS-232/422/485 (DB-9)
1 x 8-bit DIO (DB-9) (available upon request)
3 x Wi-Fi module antenna holes
2 x GbE (RJ-45) (10/100/1000Mbps)
2 x USB 2.0 (type A) & 2 x USB 3.0 (type A)
1 x Power button
1 x Line-out & 1 x Mic-in port
1 x DC-in connector
1 x DP++ & 1 x VGA port
System Reset, Programmable via Software from 1 to 255 Seconds
Type:12V DC
Connector: DC Jack
Mechanism
Environment
Tests and
Certification
Construction: sheet metal
IP Rating: IP65 front panel protection
Mounting: VESA/panel mount (*)
Weight: 1.5 kg
Dimensions (W x H x D): 230mm x 150mm x 58.3mm
Operating Temperature: -20 to 55°C
Storage Temperature: -30 to 80°C
Relative Humidity: 5 to 85% RH (non-condensing)
Shock:
OP: Half-sine, 3G @ 11ms
Non-OP: Half-sine, 5G @ 11ms
Vibration:
OP: Random, 1Grms @ 5~500Hz, 30min
Non-OP: Sweep sine, 3Grms @ 10~500Hz, 30min
Note:
*Optional items are not supported in standard model. Please contact your sales representative for more information.
Windows 10 IoT Enterprise 64-bit
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the KS070-AL
Bottom View
Top View
COM 2
(RS232/RS422/RS485)
DP++
COM 1
DC-in
Power button
VGA USB 2.0 LAN 2 LAN 1 Mic-in
Line-out
USB 3.0
Antenna holes
(RS232/RS422/RS485)
COM Ports
COM 1 and COM 2 can be an RS232, RS422 or RS485 port.
Power Button
Press to power on or power off the system.
Wireless Antenna Holes
Reserved for installing wireless antennas.
Line-out
Connects a speaker.
Mic-in
Connects a microphone.
DC-in
Plug a power adapter into this socket.
LAN Ports
Connect a network device or a Ethernet cable for network connectivity.
USB 3.0 Ports
Connect USB 3.0 devices as well as devices from previous versions such as USB
2.0 or USB 1.1.
USB 2.0 Ports
Connect USB 2.0 or 1.1 devices.
VGA Port
Connects to the VGA port of a display.
DP++ Port
Connects to the dual-mode DisplayPort of a display.
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
Top View
Right View
230
75
117.54
58.30
6
7.50
12.25
127.20
150
Left View
208.50
50.80
75
Front View
Bottom View
9
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
CFast card or M.2 card
AC power adapter
Installing Devices
The following devices can be installed in the system.
•
•
•
SODIMM
Mini PCIe card
CFast card or M.2 card
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1.
2.
Power on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing an Operating System
Depending on the method you choose to install your system, you may use a USB flash drive
or install a CD-ROM drive to run the Operating System CD.
Make sure that a CFast or an M.2 card is already installed.
1.
2.
Refer to the following chapters for information on installing a CFast or an M.2 card.
Refer to your operating system manual for instructions on installing an operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
10
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing Devices
Installing a CFast Card
The CFast card slot can be accessed externally without opening the chassis. Before installing a
CFast card, take off the CFast card slot cover.
CFast slot cover
1.
Gently insert the CFast card straight with the label on the CFast card facing up until you feel
it lock into place. Do not force the card into the slot if the card is not correctly inserted.
2.
Close the CFast card cover and attach the screw. To eject the card, push the card inward to
release the lock and pull it out.
CFast slot cover
11
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Removing the Chassis Cover
5.
1.
Make sure the system and all other peripheral devices connected to it have been powered off.
2.
Disconnect all power cords and cables.
3.
The 12 mounting screws on the top and bottom as well as both sides of the system are used
to secure the cover to the chassis. Remove these screws and put them in a safe place for
later use.
The Mini PCIe and the M.2 sockets are readily accessible after removing the chassis cover.
M.2 socket
Mini PCIe socket
Mounting screw
Mounting screw
Mounting screw
4.
Lift the cover up to open the system.
Lift the cover upward
12
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing an M.2 Card
The system is equipped with one M.2 socket, supporting the M.2 22x42mm (key B) form factor.
Use the following procedure to install an M.2 card:
1.
Align the notch at the edge of the M.2 card with the key in the connector.
2.
Insert the M.2 card into the connector.
Note:
The M.2 socket supports PCIe, USB, and SATA signals and can accommodate common
mobile broadband and storage modules. For jumper settings on switching the signal
betwen SATA and PCIe, refer to Chapter 4.
M.2 card
3.
Push down on the other end of the M.2 card and secure and card on the mainboard with the
provided mounting screw.
Mounting screw
13
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a Mini PCIe Card
The system board is equipped with one Mini PCIe slot that supports PCIe and USB signals.
Use the following procedure to install a Mini PCIe card:
1.
Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe
card with the key in the connector on the system board.
Mini PCIe card
2.
Push the Mini PCIe card down and use the provided mounting screws to secure the card on
the system board.
Mounting screw
14
Chapter 3 Installing Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
LVDS Channel and bpp Select
Clear CMOS Data
79
EIO (optional)
DC-in
DC-in
Digital I/O
10
2 SMBus
2
5
LAN 1
Front Audio
1 2
M.2
Intel
1
WGI211AT
SPK-OUT
1
2
80
1
79
9
1
10
2 SMBus
2
5
Intel
1
WGI211AT
LAN 1
(JP1)
1 (JP11) 9 10
1
2
USB 1/4 USB 3.0
Standby
Power LED
(JP1)
1 (JP11) 9 10
1
(JP10)
USB 5-6
3
2
1
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
(JP11) LCD/Inverter
Power
(JP10)
1
2
1
Battery
USB 2/3 USB 2.0
2 1
JP6
Audo Power-on Select (JP7)
1
1
Clear CMOS Data (JP6)
19
Front
Panel
6
1
5
20
COM 1-2
6
2
1
5
1
2
1
SATA 3.0
LAN 2
USB 1/4 USB 3.0
Standby
Power LED
1-2 On:
Normal (default)
USB3.0
Type C
OTG
1
1
(JP10)
USB 5-6
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
(JP11) LCD/Inverter
Power
(JP10)
1
2
1
Battery
USB 2/3 USB 2.0
1 On: Single LVDS
2 1
3
2
1
Audo Power-on Select (JP7)
1
1
Clear CMOS Data (JP6)
SW1
LVDS LCD Panel
LVDS Channel and
bpp Select (SW1)
2-3 On:
Clear CMOS Data
Front
Panel
2
6
1
5
1 Off: Dual LVDS
19
1
20
2
COM 1-2
2
6
1
5
1
2 On: VESA (24bpp)
2 Off: JEIDA or VESA
(18bpp)
SATA 0
Buzzer
DP++
39
40
SATA 3.0
1
SATA
Power
2
1
Panel Power Select (JP12)
SPI Flash
BIOS
VGA
SATA 0
Buzzer
DP++
39
40
Mini PCIe
2
2
1
Panel Power Select (JP12)
SPI Flash
BIOS
VGA
ON
LVDS LCD Panel
LVDS Channel and
bpp Select (SW1)
2
USB 2.0 1
Intel
WGI211AT
ON
USB 2.0 1
USB3.0
Type C
OTG
Mini PCIe
Intel
WGI211AT
LAN 2
Front Audio
1 2
ON
1
ON
1
80
ON
9
SPK-OUT
1
2
ON
Digital I/O
M.2
EIO (optional)
DC-in
DC-in
1
SATA
Power
You can reconfigure the system with the default values stored in the ROM BIOS if you encounter the following situations:
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
Switch 1 is used to select the LVDS channel and the color of bits per pixel.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper back to its
default setting, pins 1 and 2 On.
3. Now plug the power cord and power on the system.
15
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Auto Power-on Select
M.2 Signal Select
SPK-OUT
1
Digital I/O
79
9
1
10
2 SMBus
2
5
1
Front Audio
1 2
M.2
Intel
WGI211AT
LAN 1
1
2
3
(JP1)
1 (JP11) 9 10
LAN 2
USB 2.0 1
USB 1/4 USB 3.0
Standby
Power LED
1
(JP10)
USB 5-6
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
(JP11) LCD/Inverter
Power
(JP10)
1
2
1
Battery
USB 2/3 USB 2.0
2 1
JP7
Audo Power-on Select (JP7)
1
1
Clear CMOS Data (JP6)
LVDS Channel and
bpp Select (SW1)
19
Front
Panel
1
5
20
COM 1-2
6
2
1
5
1
2
1
USB3.0
Type C
OTG
80
1
79
9
1
10
2 SMBus
2
5
1
Intel
WGI211AT
LAN 1
3
2
1
1-2 On:
Power-on via power button
(default)
2
3
2-3 On: PCIe
Front Audio
1 2
JP1
(JP1)
1 (JP11) 9 10
LAN 2
1
2
Intel
WGI211AT
USB 2.0 1
1
USB 1/4 USB 3.0
Standby
Power LED
1
(JP10)
USB 5-6
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
(JP11) LCD/Inverter
Power
(JP10)
1
2
1
Battery
USB 2/3 USB 2.0
2 1
Audo Power-on Select (JP7)
1
1
Clear CMOS Data (JP6)
LVDS LCD Panel
3
2
1
2-3 On:
Power-on via AC power
LVDS Channel and
bpp Select (SW1)
VGA
19
Front
Panel
2
6
1
5
2
1
20
COM 1-2
JP7 is used to select the method of powering on the system. If you want the system to power
on whenever AC power comes in, set JP7 pins 2 and 3 to On. If you want to use the power
button, set pins 1 and 2 to On.
5
1
2
1
SATA 3.0
SATA 0
Buzzer
DP++
6
2
1
1
SATA
Power
39
40
Panel Power Select (JP12)
SPI Flash
BIOS
SATA 0
Buzzer
DP++
39
40
SATA 3.0
Mini PCIe
6
2
1
Panel Power Select (JP12)
SPI Flash
BIOS
2
ON
LVDS LCD Panel
VGA
1-2 On: SATA
(default)
1
2
Intel
WGI211AT
SPK-OUT
1
2
M.2
Digital I/O
EIO (optional)
DC-in
DC-in
80
ON
1
2
USB3.0
Type C
OTG
Mini PCIe
EIO (optional)
DC-in
DC-in
1
SATA
Power
JP1 is used to select the signal for the M.2 socket: SATA (default) or PCIe.
When using the JP7 “Power On” feature to power the system back on after a power failure,
the system may not power on if the power loss is resumed within 5 seconds (i.e., power
flicker).
16
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Backlight Power Select
Panel Power Select
Digital I/O
SPK-OUT
1
2
80
1
79
9
1
10
2 SMBus
2
5
1
Digital I/O
Front Audio
1 2
M.2
Intel
WGI211AT
LAN 1
(JP1)
1 (JP11) 9 10
LAN 2
1
2
Intel
WGI211AT
USB 2.0 1
USB 1/4 USB 3.0
Standby
Power LED
1
(JP10)
USB 5-6
1 2 3
JP10
(JP11) LCD/Inverter
Power
(JP10)
2
1
Battery
80
1
79
9
1
10
2 SMBus
2
5
(JP1)
1 (JP11) 9 10
1-2 On: +3.3V (default)
LAN 2
USB 2.0 1
USB 1/4 USB 3.0
Standby
Power LED
2-3 On: +5V
2
1
1
5
COM 1-2
5
1
VGA
1
SATA 0
USB3.0
Type C
OTG
6
1
5
20
COM 1-2
6
2
5
1
2
JP12
1
SATA 0
SATA
Power
DP++
39
40
1
SATA 3.0
Buzzer
1
19
Front
Panel
2
ON
ON
2
2
1
Panel Power Select (JP12)
SPI Flash
BIOS
6
2
1
SATA 3.0
Buzzer
DP++
LVDS LCD Panel
LVDS Channel and
bpp Select (SW1)
39
40
USB3.0
Type C
OTG
Mini PCIe
1
20
Mini PCIe
6
1 3 5
1-2 On: +12V
1
Clear CMOS Data (JP6)
Panel Power Select (JP12)
Front
Panel
2
1
2 1
LVDS LCD Panel
VGA
2 4 6
(JP11) LCD/Inverter
Power
(JP10)
Audo Power-on Select (JP7)
1
19
(JP10)
Battery
Clear CMOS Data (JP6)
SPI Flash
BIOS
1
1
Audo Power-on Select (JP7)
2
1
1
USB 5-6
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
USB 2/3 USB 2.0
2 1
LVDS Channel and
bpp Select (SW1)
Front Audio
1 2
2
Intel
WGI211AT
1
USB 2/3 USB 2.0
SPK-OUT
1
2
Intel
1
WGI211AT
LAN 1
1 2 3
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
EIO (optional)
DC-in
DC-in
M.2
EIO (optional)
DC-in
DC-in
2 4 6
1 3 5
3-4 On:+5V
2 4 6
1
SATA
Power
1 3 5
5-6 On: +3.3V
(default)
JP12 is used to select the power supplied with the LCD panel.
JP10 is used to select the power level of backlight brightness control: +5V or +3.3V (default).
Important:
Before powering on the system, make sure that the power settings of JP10 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
Important:
Before powering on the system, make sure that the power settings of JP12 match
the LCD panel’s specification. Selecting the incorrect voltage will seriously damage the
LCD panel.
17
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
LCD/Inverter Power Select
EIO (optional)
DC-in
DC-in
Digital I/O
SPK-OUT
1
2
80
1
79
9
1
10
2 SMBus
2
5
1
(JP1)
1 (JP11) 9 10
LAN 2
1
2
Intel
WGI211AT
USB 2.0 1
USB 1/4 USB 3.0
Standby
Power LED
1 2 3
Front Audio
1 2
M.2
Intel
WGI211AT
LAN 1
JP11
1-2 On: +12V (default)
1
(JP10)
USB 5-6
1 2 3
(JP1)
M.2 Signal Select
LCD/Inverter Power Select
Backlight Power Select
(JP11) LCD/Inverter
Power
(JP10)
1
2
1
Battery
USB 2/3 USB 2.0
2-3 On: +5V
2 1
Audo Power-on Select (JP7)
1
1
Clear CMOS Data (JP6)
LVDS Channel and
bpp Select (SW1)
19
Front
Panel
6
1
5
20
COM 1-2
6
2
5
1
2
1
SATA 0
Buzzer
DP++
39
40
1
SATA 3.0
USB3.0
Type C
OTG
Mini PCIe
2
2
1
Panel Power Select (JP12)
SPI Flash
BIOS
VGA
ON
LVDS LCD Panel
1
SATA
Power
JP11 is used to select the power level of the LCD/inverter power connector.
18
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
Top Panel I/O Ports
Bottom Panel I/O Ports
COM 2
DC-in
(RS232/RS422/RS485)
COM 1
DP++
Power button
VGA USB 2.0 LAN 2 LAN 1 Mic-in
Line-out
USB 3.0
Antenna holes
(RS232/RS422/RS485)
The top panel I/O consists of the following ports and connectors:
The bottom panel I/O consists of the following ports and connectors:
• COM ports:
COM 1 and COM 2 can be an RS232, RS422 or RS485 port.
•
•
•
•
•
•
•
•
•
19
Chapter 5 Ports and Connectors
Power button
Line-out
Mic-in
DC-in
LAN ports
USB 3.0 ports
USB 2.0 ports
VGA port
DP++ port
Chapter 5
USB Ports
Driver Installation
You may need to install the proper drivers in your operating system to use USB devices. Refer
to Chapter 8 for more information.
Wake-On-USB Keyboard/Mouse
DC-in
2
80
1
79
9
1
10
2 SMBus
2
5
LAN 1
Front Audio
1 2
M.2
Intel
1
WGI211AT
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
(JP1)
1 (JP11) 9 10
LAN 2
1
2
Intel
WGI211AT
USB 2.0 1
2
1
1
(JP10)
USB 5-6
USB 4
USB 1/4 USB 3.0
USB 1
LCD/Inverter
Power
Standby
Power LED
USB 3.0
1
2
1
Battery
USB 2/3 USB 2.0
Clear CMOS Data (JP6)
10
9
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
USB 2.0
2 1
USB 3
VCC
-Data1
+Data1
Ground
N.C
Digital I/O
VCC
-Data0
+Data0
Ground
Key
EIO (optional)
DC-in
DC-in
SPK-OUT
1
1
LVDS LCD Panel
ON
USB 2
SPI Flash
BIOS
USB 2.0
Front
Panel
2
6
1
5
20
6
2
5
1
2
1
SATA 0
Buzzer
DP++
COM 1-2
39
40
1
SATA 3.0
USB3.0
Type C
OTG
Mini PCIe
VGA
19
2
1
1
SATA
Power
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with 2 onboard USB 3.0 ports (USB 1 & USB 4) and 2 onboard
USB 2.0 ports (USB 2 & USB 3). The 10-pin connector allows you to connect 2 additional USB
2.0 ports (USB 5-6).
BIOS Setting
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
20
Chapter 5 Ports and Connectors
Chapter 5
1
79
9
1
10
2 SMBus
2
5
LAN 1
6789
(JP1)
1 (JP11) 9 10
1
2
Intel
WGI211AT
LAN 2
USB 2.0 1
USB 1/4 USB 3.0
1
(JP10)
USB 5-6
LCD/Inverter
Power
Standby
Power LED
1
2
2 1
Clear CMOS Data (JP6)
COM 2
1
ON
LVDS LCD Panel
SPI Flash
BIOS
19
Front
Panel
2
6
1
5
20
COM 1-2
39
40
6
2
5
1
2
1
SATA 0
Buzzer
DP++
2
1
1
SATA 3.0
USB3.0
Type C
OTG
Mini PCIe
VGA
COM 1
1
Battery
USB 2/3 USB 2.0
1
SATA
Power
COM 1 and COM 2 can be selected among RS232, 422 and 485.
The serial ports are asynchronous communication ports with 16C550A-compatible
UARTs that can be used with modems, serial printers, remote display terminals, and
other serial devices.
Please use the BIOS setup utility to configure serial port communication mode for COM 1
and COM 2.
BIOS Setting
Configure the serial ports including the serial communication mode in the Advanced
Configuration (“Super I/O Configuration” submenu) of the BIOS. Refer to Chapter 7 for
more information.
21
Chapter 5 Ports and Connectors
1 2345
1 2345
Front Audio
1 2
M.2
Intel
1
WGI211AT
1 2345
6789
RS232
RS422
Full Duplex
6789
N.C.
N.C.
N.C.
N.C.
80
N.C.
N.C.
N.C.
N.C.
2
DSR
RTS
CTS
RI
Digital I/O
SPK-OUT
1
EIO (optional)
DC-in
DC-in
DATADATA+
N.C.
N.C.
GND
DC-in
COM 1 (RS232/422/485) / COM 2 (RS232/422/485)
TXTX+
RX+
RXGND
COM Port Connector
DCD
RXD
TXD
DTR
GND
COM (Serial) Ports
RS485
Chapter 5
Graphics Interfaces
Audio Output
The display ports consist of the following:
DC-in
DC-in
DC-in
Digital I/O
SPK-OUT
1
EIO (optional)
1 VGA port
1 DP++ port
2
80
1
79
9
1
10
2 SMBus
2
5
1
1 2
Intel
WGI211AT
LAN 1
DC-in
Digital I/O
80
1
USB 2.0 1
1
10
2 SMBus
2
5
1
USB 1/4 USB 3.0
M.2
Clear CMOS Data (JP6)
1
(JP10)
SPI Flash
BIOS
VGA
1
Battery
2 1
ON
LVDS LCD Panel
SPI Flash
BIOS
6
1
5
DP++
5
COM 1-2
39
40
6
2
1
5
1
2
1
SATA 3.0
SATA 0
USB3.0
Type C
OTG
1
SATA
Power
5
1
2
1
SATA 0
Front Audio
1
SATA
Power
This Line-out jack is used to connect a headphone or external speakers. And the MIC-in connector is used to connect an external microphone.
Speaker Out (optional)
VGA Port
The audio speaker out connector supports 2 x 3W speaker.
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
Driver Installation
Install the audio drivers. Refer to Chapter 8 for more information.
DP++ Port
The DisplayPort is a digital display interface used to connect a display device such as a computer monitor. It is used to transmit audio and video simultaneously. The interface, which is
developed by VESA, delivers higher performance features than any other digital interfaces.
Driver Installation
Install the graphics driver. Refer to Chapter 8 for more information.
22
Chapter 5 Ports and Connectors
1
20
2
1
6
2
SATA 3.0
USB3.0
Type C
OTG
6
DP++
39
40
1
COM 1-2
Mini PCIe
2
20
Buzzer
DP++
19
Front
Panel
2
1
Front
Panel
2
Buzzer
1
19
Mini PCIe
1
2
Clear CMOS Data (JP6)
Mic-in Line-out
1
LVDS LCD Panel
LCD/Inverter
Power
USB 2/3 USB 2.0
1
2 1
1
USB 5-6
9 10
1
2
Battery
USB 2/3 USB 2.0
ON
USB 2.0 1
Standby
Power LED
VGA
(JP10)
GND
NC
Mic2-JD
Key
Line2-JD
LCD/Inverter
Power
Standby
Power LED
Front Audio
1 2
2
Intel
WGI211AT
USB 1/4 USB 3.0
VGA
1
USB 5-6
Mic2-L
Mic2-R
Line2-R
GND
Line2-L
79
9
(JP1)
1 (JP11) 9 10
LAN 2
1
2
Intel
WGI211AT
LAN 2
Intel
WGI211AT
LAN 1
(JP1)
1 (JP11) 9 10
SPK-OUT
1
EIO (optional)
2
DC-in
DC-in
Front Audio
1 2
M.2
•
•
SPK Out L+
SPK Out LSPK Out RSPK Out R+
4
1
Speaker Out
(Optional)
Chapter 5
DC-in Power Connector
RJ45 LAN Ports
DC-in
DC-in
Digital I/O
9
10
1
2
80
1
79
Digital I/O
2 SMBus
2
5
Front Audio
1 2
M.2
Intel
1
WGI211AT
LAN 1
LAN 2
80
1
79
9
1
10
2 SMBus
2
5
1
1
(JP10)
USB 2.0 1
1
(JP10)
USB 5-6
LCD/Inverter
Power
Standby
Power LED
LCD/Inverter
Power
Standby
Power LED
1
2
Intel
WGI211AT
LAN 2
USB 1/4 USB 3.0
USB 1/4 USB 3.0
Front Audio
1 2
(JP1)
1 (JP11) 9 10
LAN 1 LAN 2
1
USB 5-6
2
Intel
WGI211AT
LAN 1
(JP1)
1 (JP11) 9 10
2
USB 2.0 1
Intel
WGI211AT
SPK-OUT
1
EIO (optional)
DC-in
DC-in
M.2
EIO (optional)
DC-in
DC-in
SPK-OUT
1
1
1
2
2
1
Battery
USB 2/3 USB 2.0
1
Battery
USB 2/3 USB 2.0
2 1
2 1
Clear CMOS Data (JP6)
Clear CMOS Data (JP6)
1
1
LVDS LCD Panel
Front
Panel
2
6
1
5
20
COM 1-2
ON
39
40
VGA
5
1
2
SPI Flash
BIOS
6
2
1
USB3.0
Type C
OTG
6
1
5
20
DP++
2
1
COM 1-2
39
40
6
2
1
5
1
2
1
SATA 3.0
SATA 0
1
SATA
Power
19
Front
Panel
2
Buzzer
SATA 0
Buzzer
DP++
2
1
1
SATA 3.0
Mini PCIe
VGA
19
USB3.0
Type C
OTG
Mini PCIe
ON
LVDS LCD Panel
SPI Flash
BIOS
1
SATA
Power
Features
Connect a DC power cord to this jack. Use a power adapter within 12V DC output voltage.
Using a power adapter that does not conform to the specified voltage may fail to boot the system or cause damage to the system board.
•
2 Intel® I211AT PCI Express Gigabit Ethernet controllers
The LAN ports allow the system to connect to a local area network for Ethernet connectivity.
BIOS Setting
Configure the onboard LAN in the Advanced menu (“ACPI Configuration” submenu) of the
BIOS. Refer to Chapter 3 for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 7 for more information.
23
Chapter 5 Ports and Connectors
Chapter 5
I/O Connectors
USB OTG Connector
Serial ATA Connector & Serial ATA Power Connector
DC-in
DC-in
Digital I/O
2
80
1
79
9
1
10
2 SMBus
2
5
1
2
USB 2.0 1
LAN 2
79
9
1
10
2 SMBus
2
5
LAN 2
1
USB 2.0 1
1
USB 5-6
1
ON
SPI Flash
BIOS
Front
Panel
6
5
2
COM 1-2
2
6
1
5
1
SATA 3.0
USB3.0
Type C
OTG
Clear CMOS Data (JP6)
SPI Flash
BIOS
VGA
6
1
5
20
4
+12V
Ground
Ground
+5V
2
1
COM 1-2
39
40
6
2
1
5
1
2
1
SATA 3.0
SATA 0
Buzzer
DP++
1
19
Front
Panel
2
1
SATA
Power
1
LVDS LCD Panel
SATA Power
SATA 0
Buzzer
DP++
1
20
Mini PCIe
2
1
19
39
40
2 1
ON
1
LVDS LCD Panel
2
1
USB 2/3 USB 2.0
SATA 3.0
GND
TXP
1
TXN
GND
RXN
RXP
7
GND
2 1
1
Battery
USB3.0
Type C
OTG
Mini PCIe
2
VGA
1
2
Battery
Clear CMOS Data (JP6)
(JP10)
LCD/Inverter
Power
Standby
Power LED
1
USB 2/3 USB 2.0
1
USB 5-6
(JP10)
LCD/Inverter
Power
Standby
Power LED
1
2
Intel
WGI211AT
USB 1/4 USB 3.0
USB 1/4 USB 3.0
Front Audio
1 2
(JP1)
1 (JP11) 9 10
(JP1)
1 (JP11) 9 10
Intel
WGI211AT
80
1
Intel
1
WGI211AT
LAN 1
Front Audio
1 2
M.2
Intel
WGI211AT
LAN 1
2
M.2
DC-in
DC-in
Digital I/O
SPK-OUT
1
EIO (optional)
DC-in
DC-in
SPK-OUT
1
EIO (optional)
1
SATA
Power
USB OTG
Features
•
1 Serial ATA 3.0 port with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
The USB OTG (USB 2.0) connector is used for USB communication and it allows the system
board and the devices connected to it to switch back and forth between the roles of host
and device. When the system board is in host mode, it acts as a computer and allows USB
peripherals to be connected through the USB OTG port. And when the system board is in
device mode, it can be used to read and write to the onboard eMMC memory from your
host computer.
The Serial ATA connector is used to connect the Serial ATA device. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
BIOS Setting
Configure the Serial ATA drive in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
24
Chapter 5 Ports and Connectors
Chapter 5
LVDS LCD Panel Connector
LVDS LCD Panel & Inverter Power Connector
Pins
DC-in
DC-in
DC-in
Digital I/O
2
80
1
79
9
1
10
2 SMBus
2
5
1
Front Audio
1 2
M.2
Intel
WGI211AT
LAN 1
(JP1)
1 (JP11) 9 10
USB 2.0 1
USB 1/4 USB 3.0
1
(JP10)
USB 5-6
LCD/Inverter
Power
LCD/Inverter
Power
Standby
Power LED
8
1
2
Intel
WGI211AT
LAN 2
1
2
1
Battery
USB 2/3 USB 2.0
2 1
Clear CMOS Data (JP6)
1
LVDS LCD Panel
1
2
ON
LVDS LCD Panel
SPI Flash
BIOS
Front
Panel
2
6
1
5
20
COM 1-2
6
2
Function
Pins
Function
GND
2
GND
1
GND
3
LVDS_Out3+ (Odd_3+)
4
LVDS_Out7+ (Even_3+)
2
GND
5
LVDS_Out3- (Odd_3-)
6
LVDS_Out7- (Even_3-)
3
Dimming Control
7
GND
8
GND
4
Panel Power
9
LVDS_Out2+ (Odd_2+)
10
LVDS_Out6+ (Even_2+)
5
+3.3V
11
LVDS_Out2- (Odd_2-)
12
LVDS_Out6- (Even_2-)
6
Panel Backlight On/Off Control
13
GND
14
GND
7
LCD/Inverter Power
15
LVDS_Out1+ (Odd_1+)
16
LVDS_Out5+ (Even_1+)
8
LCD/Inverter Power
17
LVDS_Out1- (Odd_1-)
18
LVDS_Out5- (Even_1-)
19
GND
20
GND
21
LVDS_Out0+ (Odd_0+)
22
LVDS_Out4+ (Even_0+)
23
LVDS_Out0- (Odd_0-)
24
LVDS_Out4- (Even_0-)
25
GND
26
GND
27
LVDS_CLK1+ (Odd_CLK+)
28
LVDS_CLK2+ (Even_CLK+)
29
LVDS_CLK1- (Odd_CLK-)
30
LVDS_CLK2- (Even_CLK-)
31
GND
32
GND
33
DDC_CLK
34
N.C.
35
DDC_DATA
36
+3.3V
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
5
1
2
1
1
SATA 0
USB3.0
Type C
OTG
Pins
1
39
40
SATA 3.0
Buzzer
DP++
2
1
1
Mini PCIe
VGA
19
Function
SPK-OUT
1
EIO (optional)
LCD/Inverter Power Connector
1
SATA
Power
40
39
The system board allows you to connect a LCD Display Panel with the LVDS LCD panel connector and the LCD/Inverter power connector. These connectors transmit video signals and
power from the system board to the LCD Display Panel.
Refer to the right side for the pin functions of these connectors.
BIOS Setting
Configure the LCD panel in the Advanced menu (“Video Configuration” submenu) of the BIOS.
Refer to Chapter 7 for more information.
25
Chapter 5 Ports and Connectors
Chapter 5
Digital I/O Connector
Expansion Slots
DC-in
2
80
1
79
9
1
10
2 SMBus
2
5
1
Digital I/O
Front Audio
1 2
M.2
Intel
WGI211AT
LAN 1
Digital I/O
9
10
DC-in
1
2
Digital I/O
(JP1)
1 (JP11) 9 10
LAN 2
USB 2.0 1
1
2
80
1
79
9
1
10
2 SMBus
2
5
1
Intel
WGI211AT
LAN 1
1
2
Intel
WGI211AT
SPK-OUT
1
EIO (optional)
DC-in
DC-in
(JP10)
USB 5-6
Front Audio
1 2
M.2
Digital I/O
SPK-OUT
1
EIO (optional)
DC-in
DC-in
M.2
(PCIe/USB 2.0/SATA 3.0)
(JP1)
1 (JP11) 9 10
USB 1/4 USB 3.0
LCD/Inverter
Power
Standby
Power LED
LAN 2
1
2
USB 1/4 USB 3.0
2 1
ON
SPI Flash
BIOS
Front
Panel
COM 1-2
USB 2/3 USB 2.0
2
6
1
5
Clear CMOS Data (JP6)
1
LVDS LCD Panel
1
ON
SPI Flash
BIOS
19
2
1
1
VGA
SATA
Power
Front
Panel
2
6
1
5
20
DP++
6
2
5
1
2
1
SATA 3.0
SATA 0
Buzzer
The 8-bit Digital I/O connector provides monitoring and control function to external devices
connected to the connector.
COM 1-2
39
40
1
SATA 0
USB3.0
Type C
OTG
1
2 1
39
40
SATA 3.0
Buzzer
DP++
2
1
2
Battery
USB3.0
Type C
OTG
Mini PCIe
6
5
1
20
Mini PCIe
2
1
19
(JP10)
1
LVDS LCD Panel
2
1
1
USB 5-6
LCD/Inverter
Power
Standby
Power LED
Clear CMOS Data (JP6)
VGA
USB 2.0 1
1
Battery
USB 2/3 USB 2.0
1
2
Intel
WGI211AT
1
SATA
Power
Full-size Mni PCIe
(PCIe/USB)
Digital I/O Connector
Pins
Function
1
DIO7
2
DIO6
3
DIO5
4
DIO4
5
DIO3
6
DIO2
7
DIO1
8
DIO0
9
5V
10
GND
M.2 Slot
The M.2 slot on the top side of the system board is used to install M.2 (NGFF) modules. The
M.2 Type 2242 (B Key) slot can be inserted with a SATA SSD card or wireless module with the
form factor of 42mm.
Mini PCI Express Slot
The full-size Mini PCIe socket supports PCIe x1 and USB 2.0 signals and is used to install a
Mini PCIe card.
26
Chapter 5 Ports and Connectors
Chapter 5
Front Panel Connector
Standby Power LED
DC-in
80
1
79
1
10
2 SMBus
2
5
1
Digital I/O
M.2
Front Audio
1 2
Intel
WGI211AT
LAN 2
Clear CMOS Data (JP6)
1
ON
Front
Panel
2
1
1
5
20
5
1
2
1
SATA 3.0
Front
Panel
Mini PCIe
USB3.0
Type C
OTG
1
SATA
Power
1
(JP10)
Standby Power LED
1
2
1
Battery
2 1
Clear CMOS Data (JP6)
6
5
1
LVDS LCD Panel
SPI Flash
BIOS
SATA 0
Buzzer
DP++
COM 1-2
6
2
1
USB 5-6
LCD/Inverter
Power
Standby
Power LED
Reset_SW
6
39
40
1
PWR_BTN
2
USB 1/4 USB 3.0
1
2
1
USB 2.0 1
USB 2/3 USB 2.0
LVDS LCD Panel
VGA
Front Audio
1 2
2
Intel
WGI211AT
LAN 2
HDD_LED
2
2 1
19
2 SMBus
2
5
(JP1)
1 (JP11) 9 10
Battery
SPI Flash
BIOS
1
(JP10)
1
USB 2/3 USB 2.0
9
10
1
USB 5-6
LCD/Inverter
Power
Standby
Power LED
79
1
SUS_LED
USB 1/4 USB 3.0
80
1
ON
2
USB 2.0 1
2
Intel
1
WGI211AT
LAN 1
(JP1)
1 (JP11) 9 10
SPK-OUT
1
EIO (optional)
DC-in
DC-in
Intel
WGI211AT
LAN 1
DC-in
M.2
2
9
VGA
19
Front
Panel
2
6
1
5
20
COM 1-2
39
40
6
2
1
5
1
2
1
SATA 0
Buzzer
DP++
2
1
SATA 3.0
USB3.0
Type C
OTG
Mini PCIe
Digital I/O
SPK-OUT
1
EIO (optional)
DC-in
DC-in
1
SATA
Power
HDD_LED - HDD LED
This LED will be lit when the hard drive is being accessed.
RESET_SW - Reset Switch
This switch allows you to reboot without having to power off the system.
This LED will light up red when the system is in the standby mode. It indicates that
there is power on the system board. Power-off the PC and then unplug the power
cord prior to installing any devices. Failure to do so will cause severe damage to the
motherboard and components.
PWR_BTN - Power Button
This switch is used to power on or off the system.
SUS_LED - Status LED
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
Pin Pin Assignment
HDD_LED
SUS_LED
6
HDD_LED
3
GND
4
SUS_LED
2
V_LED
Pin Pin Assignment
RESET_SW
PWR_BTN
5
Reset Button
3
GND
1
Power Button
3
GND
27
Chapter 5 Ports and Connectors
Chapter 5
DC-in
DC-in
Digital I/O
2
80
1
79
9
1
10
2 SMBus
2
5
Digital I/O
LAN 1
Front Audio
1 2
M.2
Intel
1
WGI211AT
SPK-OUT
1
EIO (optional)
DC-in
DC-in
2
80
1
79
9
1
10
2 SMBus
2
5
SMBus
Intel
1
WGI211AT
LAN 1
Front Audio
1 2
M.2
DC-in
DC-in
SPK-OUT
1
EIO (optional)
(JP1)
1 (JP11) 9 10
USB 2.0 1
USB 1/4 USB 3.0
1
(JP10)
USB 5-6
LCD/Inverter
Power
Standby
Power LED
1
2
1
Battery
USB 2/3 USB 2.0
2 1
Clear CMOS Data (JP6)
2
USB 2.0 1
Intel
WGI211AT
LAN 2
GND
3.3V
LAN 2
1
2
Intel
WGI211AT
(JP1)
1 (JP11) 9 10
USB 1/4 USB 3.0
2
Front
Panel
Clear CMOS Data (JP6)
6
1
5
20
39
40
6
2
2
SPI Flash
BIOS
19
VGA
1
Front
Panel
2
6
1
5
20
1
DP++
6
2
5
1
2
1
USB3.0
Type C
OTG
1
SATA
Power
Connect to the battery connector
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
28
Chapter 5 Ports and Connectors
COM 1-2
39
40
SATA 0
Buzzer
SATA
Power
Battery
2
1
1
SATA 3.0
SATA 0
USB3.0
Type C
OTG
1
5
1
SATA 3.0
Buzzer
DP++
COM 1-2
1
LVDS LCD Panel
Mini PCIe
2
5
2 1
2 1
1
Mini PCIe
VGA
19
2
1
Battery
ON
ON
SPI Flash
BIOS
(JP10)
1
Battery
USB 2/3 USB 2.0
1
1
USB 5-6
LCD/Inverter
Power
Standby
Power LED
LVDS LCD Panel
2
1
1
GND
SMB_DATA
SMBus Connector
3V3SB
SMB_CLK
SMB_ALERT
Battery
Chapter 6
Chapter 6 - Mounting Options
Wall Mount
2.
Select a place on the wall where you will mount the Panel PC.
3.
Use the provided mounting screws to attach “wall mount bracket 1” to the wall.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
Mounting screw
The wall mount kit includes the following:
•
•
2 wall mount brackets
Bracket screws
Wall mount bracket 1
4.
Wall mount bracket 1
1.
Attach the other bracket (wall mount bracket 2) to the rear of the Panel PC.
Wall mount bracket 2
Mounting screw
Before starting any installation procedure, attach the poron foam to the Panel PC.
Wall mount bracket 2
Hooks
Poron foam
29
Chapter 6 Mounting Options
www.dfi.com
Chapter 6
5.
Panel Mount
Slide the Panel PC to "wall mount bracket 1" to attach the two brackets with the hooks.
Then tighten the screw to secure the assembly in place.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
Screw
The panel mounting kit includes the following:
•
6 mounting clamps
1.
Before starting any installation procedures, attach the poron foam to the Panel PC.
Poron foam
2.
Select a place on the panel (or wall) where you will mount the Panel PC.
3.
Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (210.5mm
x 132.2mm) and ensure that the Panel PC can be fitted into the panel properly.
5
132.20
Mounting hole
Panel
210.50
30
Chapter 6 Mounting Options
www.dfi.com
Chapter 6
4.
Insert the Panel PC from the outside surface of the panel into the mounting hole until it is
properly fitted against the panel.
5.
Position the mounting clamps along the rear edges of the Panel PC and insert them into the
slits around the Panel PC.
Note:
The flat panel thickness is less than 5mm.
Slit for mounting the clamp
5
White plastic cap
132.20
Mounting clamp
6.
The first and second clamps must be positioned and secured diagonally prior to mounting
the rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing
the white plastic cap onto the back of the panel. The illustration below shows that all
210.50
clamps are properly mounted.
31
Chapter 6 Mounting Options
www.dfi.com
Chapter 7
Chapter 7 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your
system configuration.
Keys
Function
Right and Left
arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
+ (plus key)
Scrolls forward through the values or options of the highlighted field.
- (minus key)
Scrolls backward through the values or options of the highlighted
field.
<F1>
Displays general help
<F2>
Pervious values
<F3>
Optimized defaults
<F4>
Saves and resets the setup program.
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
Entering the BIOS Setup Utility
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
32
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1980 to 2099.
33
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ACPI Configuration
CPU Configuration
This section configures system ACPI parameters.
This section configures the CPU.
Wake on LAN
EIST
Enable or disable WOL (wake-on-LAN) to wake the system through an Ethernet adapter.
Enable or disable the Enhanced Intel® SpeedStep® Technology, which helps optimize
the balance between system’s power consumption and performance. After it is enabled
in the BIOS, you can take advantage of its offering by setting power schemes from the
operating system’s power options.
After G3
Specify which state the system should be in when power is re-applied after a power
failure (G3, the mechanical-off, state).
Turbo Mode
Always On The system is powered on.
Always Off The system is powered off.
Enable or disable processor turbo mode, which allows the processor core to automatically run faster than the base frequency by taking advantage of thermal and power
headroom. Note this option is not available on the Core™ i3 processor.
BGRT Logo
C-States
Enable or disable the display of an operating system logo or image during boot using
the BGRT (Boot Graphics Resource Table) mechanism.
Enable or disable CPU power management. It allows the CPU to go to C states when
it’s not 100% utilized.
34
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Video Configuration
Audio Configuration
This section configures the video settings.
This section configures the audio settings.
Primary Display
Select the primary display for the system from the following options:
HD Audio
IGD: integrated graphics devices
Control the detection of the high-definition audio devices.
PCIe: PCIe graphics devices
Disabled
High-definition audio devices will be unconditionally disabled.
Integrated Graphics Device
Enable, disable or automatically detect the integrated graphics device.
Enabled
High-definition audio devices will be unconditionally enabled.
PTN3460 Function
Enable or disable the PTN3460 LCD features. If enabled, the LCD panel type and the
panel color depth options will be shown.
Auto
High-definition audio devices will be enabled if present and disabled otherwise.
LCD Panel Type
Select the type of LCD panel connected to the system’s LCD connector. Please check the
specification of your LCD monitor.
Panel Color Depth
Select the LCD panel color depth: 18 bit, 24 bit, 36 bit, and 48 bit.
Chapter 7 BIOS Setup
35
www.dfi.com
Chapter 7
SATA Configuration
This section configures SATA devices. It also shows the information about the installed
SATA drives.
SATA Speed
Select Serial ATA device speed from these options: Gen1 (1.5 Gbit/s), Gen2 (3 Gbit/s) or Gen
3 (6 Gbit/s).
SATA Mode Selection
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
Serial ATA Port 0 and 1 and Hot Plug
Enable or disable each Serial ATA port and its hot plug function.
SATA Port 0: It controls the signal of the CFast card slot.
SATA Port 1: It controls the signal of the M.2 slot.
SATA Controller
Enable or disable the Serial ATA controller.
36
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
USB Configuration
PCI Express Configuration
This section configures the parameters of USB devices.
This section configures the settings of PCI Express root ports.
XDCI Support
PCI Express Root Port 1
Enable or disable xDCI device (Extensible Device Controller Interface) to enable or disable the USB OTG device on the board.
Controls the PCIe signal of the M.2 slot.
PCI Express Root Port 3
Controls the PCIe signal of LAN Port 1.
PCI Express Root Port 4
Controls the PCIe signal of LAN Port 2.
PCI Express Root Port 5
Controls the PCIe signal of Mini PCIe slot.
Press “Enter” to enter the configurations for each PCIe root port as shown on the next page.
37
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PCI Express Configuration
Console Redirection
This section configures the settings of PCI Express root ports.
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
PCI Express Root Port
Console Serial Redirect
Enable or disable each PCI Express root port.
Enable or disable the console redirection function. (The default is disabled.) If you select
to enable it, please configure the following parameters for serial communication between the system and a remote station:
Hot Plug
Enable or disable the hot plug function.
Terminal type: VT_100, VT_100+, VT_UTF8, or PC_ANSI.
Baud rate: 115200, 57600, 38400, 19200, or 9600.
Data bits: 8 bits or 7 bits.
Parity: None, Even or Odd.
Stop bits: 1 bit or 2 bits.
Flow control: None, RTS/CTS or XON/XOFF
PCIe Speed
Select the speed of the PCI Express Root Port: Auto, Gen1 (2.5 GT/s) or Gen2 (5 GT/s).
This is the global setting for all of the designated serial ports for console redirection.
38
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Super I/O
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
COM A and COM B
Enable or disable the serial redirection function for each of the serial ports on the system. And configure the serial communication parameters to be used between the system
and a remote station.
COM Port 1 and COM Port 2
UseGlobalSetting
Enable or disable each serial port.
Choose to use the pre-configured global settings from the previous menu or configure a
different setting for each serial port.
Disable Disable this serial port.
Enable Enable this serial port.
It also shows the Base I/O address and the assigned interrupt number.
Type
Choose RS232, RS422 or RS485 (Peer-to-Peer) for the serial port type for COM port 1 and 2.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable WDT.
Input any value between 1 and 255.
39
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Security
PC Health Status
This section d
This section configures the Trusted Platform Module (TPM) function.
tatus.
TPM Availability
Show or hide TPM availability and its configurations.
TPM Operation
Select one of the supported operation to change the TPM2 state.
Clear TPM
Remove all TPM ownership contents.
Set Supervisor Password
Set the administrative password for entering the BIOS utility or upon the entering of the
power-on self-test (POST) process. The length of the password must be greater than 1
character and less than or equal to 10 characters.
40
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Boot
Note:
The BIOS supports only UEFI boot but not legacy.
EFI
Enter this menu to select the priority of the UEFI boot devices. Use the “+” key to move
an item up or the “-” key to move an item down. The one on the top of the list has the
highest priority.
Setup Prompt Timeout
Select the number of seconds the system will wait before booting the original firmware selection.
NumLock State
This allows you to determine the default state of the numeric keypad at boot. By
default, the system boots up with Num Lock on. When set to Off, the function of the
numeric keypad is the arrow keys.
Network Stack
Enable or disable network stack. It supports the operation of these functions or software: Windows 8 BitLocker Network Unlock and UEFI IPv4/IPv6 PXE.
PXE Boot Capability
Enable or disable Preboot eXecution Environment (PXE) boot through the Ethernet.
This function can only be enabled if the Network Stack support is enabled.
USB Boot
Enable or disable USB boot from a flash drive.
41
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Exit
Exit Saving Changes
Select this field and press <Enter> to exit BIOS setup and save your changes.
Load Optimal Defaults
Select this field and press <Enter> to load the optimal defaults.
Discard Changes
Select this field and press <Enter>to exit the BIOS setup without saving your changes.
Save Setting to file
Select this option to save BIOS configuration settings to a USB drive. The operation will
fail if there aren’t any USB devices detected on the system. The saved configuration will
have the DSF file extension and can be used for restoration.
Restore Setting from file
Select this option to restore BIOS configuration settings from a USB drive. Note that
this option will not be available if there aren’t any USB devices detected on the system.
42
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions about how to
update BIOS with the flash utility.
1. The Intel® Management Engine has already been integrated into this system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing BIOS updating procedure. For your convenience, we
will also provide you with an auto-execution file in the BIOS file downloaded. This auto-execution file will bring you directly to the flash utility menu soon after system boots up and finishes
running the boot files in your boot disk.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
RRead file successfully.
3. If you do not follow the methods above, the Intel® Management Engine will not be
updated and will cease to be effective.
|
Note:
|
a. You can take advantage of flash tools to update the default
configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
|
|
(path= “platform.ini”)
Information
Please do not remove the AC power
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: AL551
New BIOS Model name: AL551
Current BIOS version: 68.08A
New BIOS version: 68.08A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\SU25x>_
100%
100%
43
Chapter 7 BIOS Setup
www.dfi.com
Chapter 8
Chapter 8 - Supported Software
The CD that came with the system board contains drivers, utilities and software applications
required to enhance the performance of the system board.
Insert the CD into a CD-ROM drive. The auto-run screen (the Utility and Manual CD) will appear. If the “Auto-run” does not automatically start, please go directly to the root directory of
the CD and double-click “Setup”.
Auto Run Page (For Windows 10)
44
Chapter 4 Supported Software
Chapter 8
Intel Chipset Software Installation Utility
3. Go through the readme document for more installation tips
then click “Install.”
The Intel Chipset Device Software is used for updating Windows® INF files so that the Intel
chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Software Installation Utility” in the main menu.
1. Setup is ready to install
the utility. Click “Next” to
continue.
4. After the installation is complete, click “Restart Now”.
Restarting the system will allow
the new software installation to
take effect.
2. Read the license agreement,
then click “Accept” if you
accept the terms and conditions.
45
Chapter 4 Supported Software
Chapter 8
Intel Graphics Drivers
3. Go through the Readme document for system requirements
and installation tips, then click
“Next”.
To install the driver, click “Intel Graphics Drivers” in the main menu.
1. Setup is now ready to install
the graphics driver. Click
“Next” to continue.
4. Setup is now installing the
driver. Click “Next” to continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is
enabled. When this is enabled and the system reboots after driver installation, the screen will
turn blank for 1 to 2 minutes (while WinSAT is running) before the Windows 7/ Windows 8
desktop appears. The “blank screen” period is the time Windows is testing the graphics performance.
We recommend that you skip this process by disabling this function and click “Next”.
2. Read the license agreement,
then click “Yes” if you accept
the terms and conditions.
5. Click “Yes, I want to restart this
computer now”, then click “Finish” to exit the setup program.
Restarting the system will allow the
new software installation to take
effect.
46
Chapter 4 Supported Software
Chapter 8
Intel LAN Drivers
4. Click “Install” to begin the
installation.
To install the driver, click “LAN Drivers” in the main menu.
1. Setup is ready to install
the driver. Click “Next” to
continue.
5. After the installation is
complete, click “Finish” to
exit the setup program.
2. Click “I accept the terms in
the license agreement” if
you accept the terms and
conditions, then click “Next”.
3. Select the program features
you want to install then
click “Next” to continue.
47
Chapter 4 Supported Software
Chapter 8
Intel Trusted Execution Engine Driver
To install the driver, click “Intel TXE Drivers” in the main menu.
1. Select “I accept the terms
in the License Agreement”,
then click “Next.”
3. The screen displays the
installation status in
progress.
4. Click “Finish“ when the
installation is complete.
2. The screen shows the components that will be installed. Click
“Next” to continue.
48
Chapter 4 Supported Software
Chapter 8
Realtek Audio Drivers
IO Driver
To install the driver, click “Realtek Audio Drivers” in the main menu.
To install the Intel® Serial IO driver, click “IO Driver” in the main menu.
1. Setup is now ready to install the
audio driver. Click “Next” to start
the installation.
1. Setup is ready to install the
driver. Click “Next” to continue.
2. Follow the on-screen instructions to proceed with the setup
program. Click “Next” each time
you finish a step.
2. Read the license agreement carefully.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement, then click
“Next”.
3. Click “Yes, I want to restart my
computer now” then click “Finish.”
Restarting the system will allow the
new software installation to take
effect.
49
Chapter 4 Supported Software
Chapter 8
3.
Read the file information for installation information, then click “Next”.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
50
Chapter 4 Supported Software
5.
Setup is now installing the driver.
6.
Click “Finish” to exit setup.
Chapter 8
eGalaxTouch Touch Panel Driver
To install this driver, click “eGalaxTouch Touch Screen Driver” in the main menu.
3. Setup detects that an extra
RS232 interface driver needs to
be installed for the eGalaxTouch
controller. Please check to install
the driver.
1. Setup is ready to install the driver.
Click “Next” to continue.
4. Select the setup type that best
suits your needs.
2. Read the license agreement carefully. Click “I accept the terms of the
license agreement” if you agree with
the terms in the agreement, then click
"Next”.
51
Chapter 4 Supported Software
Chapter 8
Wi-Fi Driver
5. Select whether to support the
multi-monitor system.
To install the Wi-Fi driver, click “WLAN Driver” in the main menu.
1. Select the language for the installation.
6. Select the installation folder. Follow
the rest of the steps on the screen
to complete the installation procedure.
2. Setup is now ready to install the
audio driver. Click “Next” to start
the installation.
52
Chapter 4 Supported Software
Chapter 8
3. Read the license agreement carefully. Click “I accept the terms of the
license agreement” if you agree with
the terms in the agreement, then click
"Next”.
4. Click “Finish” to exit the installation
wizard.
53
Chapter 4 Supported Software
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising