DFI | EC510/511-KH | manual | Dfi EC510/511-KH Manual

Dfi EC510/511-KH Manual
EC510/511-KH
User’s Manual
Preliminary
Version
A55900944
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2019. All Rights Reserved.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
PS/2 KB/MS Power Select........................................................ 19
Copyright.............................................................. 2
COM1/COM2 RS232 Power Select............................................ 20
FCC and DOC Statement on Class A...................... 2
DIO Power Source Select (Pins 0~7)....................................... 20
About this Manual................................................. 4
COM1/COM2 RS232/422/485 Select........................................ 21
Warranty ............................................................. 4
COM3/COM4 RS232/422/485 Select......................................... 22
Static Electricity Precautions.................................. 4
DIO High/Low Select (DIO 0~3).............................................. 23
Safety Measures................................................... 4
DIO High/Low Select (DIO 4~7).............................................. 23
Safety Precautions................................................ 5
Chapter 5 - Ports and Connectors.......................... 24
About the Package................................................ 5
Front Panel I/O Ports.............................................................. 24
USB Ports.................................................................................................... 24
COM (Serial) Ports....................................................................................... 25
Chapter 1 - Introduction........................................ 6
Rear Panel I/O Ports............................................................... 25
Overview..................................................................................6
Specifications............................................................................7
RJ45 LAN Ports............................................................................................ 26
Display Interfaces........................................................................................ 26
USB Ports.................................................................................................... 27
9~36V DC-in............................................................................................... 27
Getting to Know the EC510/EC511-KH.......................................8
I/O Connectors....................................................................... 28
Key Features............................................................................6
PS/2 KB/MS Connector................................................................................. 28
SATA (Serial ATA) Connectors....................................................................... 28
SATA (Serial ATA) Power Connectors............................................................. 29
SMBus Connector ....................................................................................... 29
Rear Audio Connector.................................................................................. 30
Digital I/O Connector & DIO Power.............................................................. 30
12V DC-out................................................................................................. 31
Front Panel Connector ................................................................................ 31
Expansion Slots........................................................................................... 32
LPC Connector............................................................................................. 33
LAN Ports (daughter board)........................................................................ 34
Digital I/O Connector (daughter board)........................................................ 34
Mechanical Dimensions.............................................................9
Chapter 2 - Getting Started................................... 10
Chapter 3 - Installing the Devices.......................... 11
Removing the Chassis Cover.................................................... 11
Installing a SODIMM............................................................... 12
Installing a 2.5” SATA Drive.................................................... 13
Chapter 6 - Mounting Options............................... 35
Installing a Mini PCIe Card...................................................... 14
Installing an M.2 Card............................................................. 15
Installing a PCI or PCIe Expansion Card................................... 16
Installing a CPU...................................................................... 17
Chapter 4 - Jumper Settings.................................. 19
Clear CMOS Data.................................................................... 19
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual can be obtained from the DFI website at www.dfi.com.
Todownload the user’s manual from our website, please go to “Support” > “Download Center.”
On the Download Center page, select your product or type the model name and click “Search”
to find all technical documents including the user’s manual for a specific product.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
Warranty
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
1.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
4.
We will not be liable for any indirect, special, incidental or damages to the product that
has been modified or altered.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 EC510/EC511-KH system unit
• 1 CD disk includes: Drivers/Manual
• Danger of explosion if battery incorrectly replaced.
Optional Items
• Replace only with the same or equivalent type recommend by the manufacturer.
• Wall Mount kit
• Power Cord
• Power Adapter (100W/120W/160W)
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview
Model Name
EC510/EC511-KH
Processor
7th Generation Intel® CoreTM processors
Chipset
Intel® CM238, Intel® ® QM175 Chipset
LAN
6 LAN ports (or 4 PoE + 2 LAN ports)
COM
5 COM ports
Display
VGA
HDMI/DVI (DVI-D signal)
HDMI or DP (DP available upon request)
Front Panel
USB
4 USB 3.0 & 2 USB 2.0 Type A ports
DIO
16-bit digital input/output
Power
9~36V DC-in
Rear Panel
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
Processor
7th Generation Intel® CoreTM Processors, BGA1440 Socket
• Intel® Xeon® Processor E3-1535M v6, Quad Core, 8M Cache, 3.1GHz
(4.2GHz), 45W
• Intel® Core™ i7-7820EQ Processor, Quad Core, 8M Cache, 3.0GHz
(3.7GHz), 45W
• Intel® Core™ i5-7440EQ Processor, Quad Core, 6M Cache, 2.9GHz
(3.6GHz), 45W
• Intel® Core™ i5-7442EQ Processor, Quad Core, 6M Cache, 2.1GHz
(2.9GHz), 25W
• Intel® Core™ i3-7100E Processor, Dual Core, 3M Cache, 2.9GHz, 35W
• Intel® Core™ i3-7102E Processor, Dual Core, 3M Cache, 2.1GHz, 25W
Chipset
Intel® CM238 Chipset
Intel® QM175 Chipset
Memory
Two 260-pin SODIMM
• Supports dual-channel DDR4 2400MHz
• Supports up to 32GB system memory
• CM238 supports ECC
Graphics
Intel® HD Graphics
OpenGL 5.0, DirectX 11, OpenCL 2.1
• Supports these codecs:
HW Decode: HEVC/H.265, H.264, M/JPEG, MPEG2, VC1/WMV9, VP8
(8-bit), VP9 (10-bit)
HW Encode: MPEG2, HEVC/H.265, M/JPEG, VP8
Expansion
•
•
•
•
Front I/O Ports
-
One status and one HDD LED
2 x RS-232/422/485 (DB-9) (RS-232 with power)
2 x USB 2.0 (type A)
1 x Power Button
1 x Reset Button
4 x Antenna Hole
Rear I/O Ports
-
6
2
4
1
1
1
1
1
Power
Power input voltage: 9~36V DC-in (terminal block connector)
Security
TPM 2.0 (optional)
Cooling System
Fanless with heatsink
Environment
• Operating Temperature:
- 0 to 50°C (HDD)
-20 to 60°C (SSD)
-40 to 70°C (optional)
• Storage Temperature:
-20 to 85°C
• Relative Humidity:
5 to 95% RH (non-condensing)
Construction
• Metal + Aluminum
Mounting
• Wall mount
- Mounting brackets and screws (optional)
Dimensions
• 235mm x 102.5mm x 222mm (W x H x D)
Weight
• 4.1 kg
OS Support
• Linux
• Windows 10 IoT Enterprise 64 Bit
Other Features
System Reset, Programmable via Software from 1 to 255 Seconds
Standards and
Certifications
• Shock:
Half sine wave 3G, 11ms, 3 shock per axis
• Vibration: IEC68-2-64
• Certifications: CE, FCC Class A, Microsoft Azure
• Output displays:
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I: resolution up to 1920x1200 @ 60Hz
HDMI: resolution up to 4096x2160 @ 24Hz
DP: resolution up to 4096x2304 @ 60Hz
Triple/Dual
Display
VGA (+)
DVI-I (DVI-D signal) / HDMI (HDMI available upon request) (+)
HDMI / DP (DP available upon request)
Storage
• Two 2.5" SATA Drive Bay
• SATA 3.0 port with data transfer rate up to 6Gb/s
Ethernet
• 4 x Intel® I210IT PCIe (10/100/1000Mbps)
• 1 x Intel® I211IT PCIe (10/100/1000Mbps)
• 1 x Intel® I219LM with iAMT11.0 PCIe (10/100/1000Mbps) (only
Intel® Xeon® & Core™ i7/i5 support iAMT)
1
1
1
1
x
x
x
x
x
x
x
x
x
x
x
x
PCIe x16 (EC511-KH only) or 1 x PCI (EC510-KH only)
M.2 2280 M key (PCIe x4 NVMe, Intel optane memory support)
full/half-size Mini PCIe with Mini SIM socket (PCIe & USB)
full/half-size Mini PCIe with Mini SIM socket (USB)
GbE (RJ45) or 2 x GbE (RJ45) + 4 x PoE
RS-232/422/485 + 1 x RS232 (DB-9)
USB 3.0 (type A)
VGA
DVI (DVI-D signal)/HDMI (HDMI available upon request)
HDMI/DP (DP available upon request)
Line-out
Mic-in (available upon request)
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the EC510/EC511-KH
Front I/O Ports
Power Button with LED (Green)
Press to power on or power off the system.
Front Panel
Power Button(1)
USB 2.0
Status LED
HDD LED
Reset Switch
Reset Button
Press to reset the system.
COM 2 COM 1
HDD LED (Red)
Indicates the status of hard disk drives.
Remote Power Switch
HDD LED
HDD State
Disk access
activity
LED Behavior
Blink
Disk drives present or not present
Off
Status LED (Orange)
Indicates system status as below.
Antenna holes
Status LED
Rear Panel
DVI-D(2) HDMI(3
(DVI-I connector)
USB 3.0
LAN1 LAN2
DC-in
Suspend Mode
S0
Sleep
S4, S5
LED Behavior
Always ON
Blinking
Off
Remote Power-on/off Switch Connector
Connects distant power on/off switch.
USB 3.0/2.0 Ports
Connect to USB 3.0 as well as devices based on previous USB versions.
COM Ports
All COM ports can be selected among RS232, RS422 and RS485.
COM1 and COM2 can be selected between RS232 and RS232 with power via jumper settings.
Digital IO
Mic-in, Line-out
PoE 1~4
or
LAN 3~6
DIO Connector
The DIO connector provides 16-bit digital input/output.
Expansion slot
DVI-D (DVI-I connector) / HDMI / VGA Connector
Connects the DVI-I / HDMI / VGA connector of an LCD monitor.
VGA
COM3
COM5
COM4
Line-out and Microphone Ports
Connect audio devices such as microphones and speakers.
Notes:
1. Please gently press the power button to avoid possible damages.
2. This port can be in DVI-D or HDMI (HDMI available upon request).
Gigabit LAN Ports (1~6)
Connect the system to a local area network.
LAN 3~6 can be Power over Ethernet (PoE) that is capable of delivering 15.4W of power to
connected devices.
3. This port is a DP/HDMI combo port but can only transmit either HDMI or DP signals (as indicated
on the panel). Please plug in a DP or an HDMI cable with the right orientation and alignment to
avoid damage to the connector. You should feel resistance (due to a pin on the right) if the cable is
not inserted correctly. For detailed instructions, see https://youtu.be/SUj07rfN5l8.
Aligning side
(left)
Angled-corner
Angled-corner
pin
(up)
DC-in
DC 9~36V power input via a terminal block connector.
Align this edge with the
left side of the connector
PCIe Expansion Slot
Provides PCIe or PCI expansion connectivity via a riser card.
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
Motherboard Dimensions
Chassis Dimensions
209.55
Rear View
216.70
221.20
Gold finger
PCIE X4
Gold finger
PCIE X16
mini PCIe
Left View
Right View
102.50
50
235.00
228
Front View
9
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
•
SATA hard drive
AC power adapter
Optical drive (for installing software/drivers)
Memory module
Installing Devices
The following devices can be installed in the system.
•
•
•
•
Memory modules
SATA hard drives
Mini PCIe and M.2 cards
PCIe or PCI expansion cards
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1.
2.
Power on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing an Operating System
To install an OS, you need an optical drive or a USB flash drive and boot from such a device.
Make sure a 2.5” SATA drive is already installed.
1.
2.
Refer to the following chapters for information on installing SATA drives.
Refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system requires you to install drivers for some devices to operate properly. Refer to the
Supported Software chapter for instructions on installing the drivers.
10
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing the Devices
4.
Removing the Chassis Cover
1.
Make sure the system and all other peripherals connected to it have been powered off.
2.
Disconnect all power cords and cables.
3.
The 6 mounting screws on the left and right sides and bottom of the system are used to
secure the cover to the chassis. Remove these screws and put them in a safe place for
later use.
Lift the cover upward to open the system.
Chassis screw
Chassis screw
Chassis screw
11
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a SODIMM
To remove a SODIMM, gently spread the retaining clips at each end of the SODIMM socket. The
SODIMM should pop out of the socket. Lift the SODIMM away from the socket on the mainboard.
Grasp the module by its edges and align the SODIMM’s notch with the socket’s key, then
insert the SODIMM into the socket at an angle and push it down until the retaining clips
snap into place.
DIMM1
DIMM2
The installed SODIMM
Spread the retaining clips
to release the installed
SODIMM
Notes:
1. The system supports dual-channel configuration. To enable dual-channel,
populate both SODIMM sockets.
2. If you plan to install only one SODIMM, install it in the DIMM1 socket (lower
one and farther from the center of the mainboard).
3. The SODIMM sockets can only accept DDR4 memory modules. Please do not
install other types of memory modules.
12
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a 2.5” SATA Drive
3.
The system can accommodate two SATA drives. Please use the following procedure to install a
SATA drive in the system.
1.
Place the SATA drive with the HDD bracket into the system. Align the mounting holes on the
HDD bracket with the mounting holes on the SATA drive bay and use the provided screws to
secure the drive in place.
The SATA HDD bracket is included in the product package. Locate the SATA drive bay on
which the SATA HDD bracket will be mounted.
Mounting Screw
SATA drive bay
4.
2.
Insert the SATA drive into the HDD bracket and secure it in place with the provided screws
(black screws). The HDD bracket can accommodate two SATA drives.
Mounting screw
Connect the other end of the SATA data cable and the SATA power cable to the SATA data
and SATA power connector on the mainboard respectively.
SATA data connector
Mounting screw
SATA cables
Mounting screws
SATA power connector
Note:
Connect SATA cables before affixing the SATA drive on the HDD bracket as the HDD
bracket would prevent access to the SATA connectors of the drive.
13
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a Mini PCIe Card
The system board is equipped with 2 Mini PCIe slots with Mini SIM card sockets to support a
variety of wireless LAN and mobile broadband communication modules. Mini PCIe slot 1 provides
both USB and PCIe interfaces whereas Mini PCIe slot 2 provides only USB interface.
The Mini PCIe sockets are located on the mainboard. You need to revmove the riser card and
daughter board to access them.
1.
The 4 mounting screws on the daughter board are used to secure the board to the
mainboard. Remove these screws and put them in a safe place for later use. To disengage
the daughter board from the mainboard, gently pull the card out of the connector.
Grasp the Mini PCIe card by its edges and align the notch in the connector of the Mini PCIe
card with the notch in the connector on the system board.
The 4 mounting screws (plus the two fasteners used on DVI-D connector) affix the front bezel to the system as shown in the following pictures. Remove these screws and put them in
a safe place for later use.
Mini PCIe 2
Mini PCIe 1
Daughter board
mounting screw
2. Secure the card on the mainboard with the provided mounting screw.
SIM 2
3.
If the Mini PCIe card has antennas, route the antennas to the antenna holes on the front
chassis of the device.
Antenna holes
Front bezel
mounting screw
14
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a SIM Card
Installing an M.2 Card
Open the SIM card socket by pushing the white latch inward.
The onboard M.2 Type 2280 connector (M Key) supports PCIe NVMe modules up to PCIe Gen 3.0
x4 bandwidth. Note that only SKUs with Intel® QM175 Chipset support M.2 expansion.
SIM 2
Push the latch
inward to open it
Insert the SIM card into the slot. Please place the card with the IC facing down and the angled corner aligning with the socket's angled corner so it will be correctly in contact with the
system board.
To install an M.2 card, insert the bottom edge of the M.2 card into the connector, and then
secure the card to the standoff with the provided mounting screw.
Flip the cover up to open it
Close the slot's cover and lock the slot by pushing the white latch outward.
Mounting Screw
Close the cover and lock it
15
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a PCI or PCIe Expansion Card
2. Insert the expansion card into a PCI or PCIe slot on the riser card. Ensure the card is properly
seated into the slot and secure the bracket in place.
Important:
When inserting expansion cards into the system, please select a standard card
within 167.65mm (as shown in the picture below) in order to fit into the expansion slot.
PCI card
1.
The PCI and PCIe slots on the riser card inside the system are used to install expansion
cards. To install an expansion card you need to first remove the slot plate and bracket by
uninstalling the screw on the front chassis.
Slot plate
Front View
Note:
The EC511-KH has one PCIe x16 slot with the H120-1E riser card, whereas the EC510KH has one PCI slot with the H320-1P riser card.
Mounting screw and bracket
16
Chapter 3 Installing the Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
PS/2 KB/MS Power Select
Clear CMOS Data
3
2
1
1-2 On: Normal
(default)
JP1
Clear CMOS
Data (JP1)
2
10
1
9
1
1
1
1
DIO
JP3
1
JP2
DIO Power
1
Mini PCIe 2
USB 2.0
USB 13/14
10
1
9
SIM
2
2
13
USB 1/2 USB 3.0
DIO
JP3
1
JP2
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
1
9
USB 2.0
USB 13/14
10
1
9
USB 11-12
USB 2.0
13
COM 4
29
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
SIM
2-3 On: Clear CMOS Data
USB 1/2 USB 3.0
1
(JP5)
6
2
1
2
1
10
1
2
9
10
2
HDMI (default)/DP
29
1
1
(JP6)
6
SIM
2
1
4
1
4
HDMI (default)/DP
1
1
1
3
4
2
10
1
JP8
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
STB_LED
PCIe x16 (PCIE1)
6
1
2
10
4
DC-in
PCIe x4 (PCIE2)
2
1
1
1
STB_LED
PCIe x16 (PCIE1)
9
16
4-pin power
PWR_BTN_1
1
10
COM 1
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
+
+
DC-in
1
2
1
1
1
3
9
COM 1
1
1
2
6
10
16
4-pin power
COM 2
SATA Power
VGA
M.2 Type 2280
(PCIe)
9
10
2
2
1
1
(JP10) (JP16)
6
6
1
1
1
1
10
1
2
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
1
2
6
1
2
COM 3
COM 2
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
1
(JP12) (JP18)
6
6
21
1
Mini PCIe 1
2
2
1
1
(JP10) (JP16)
6
6
DVI
1 2 3
2-3 On: 5V_standby
1
9
(JP13) (JP19)
6
6
JP7
USB 3/4 USB 3.0
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
10
COM 4
1
(JP5)
6
COM 2
COM 2
Reset
2
COM 3
1
Mini PCIe 1
9
COM 6
USB 11-12
USB 2.0
1
2
USB 3/4 USB 3.0
1 2 3
1-2 On: 5V
COM 5 6
10
1
14
30
EXC
1
1
(JP12) (JP18)
6
6
21
2
2
9
Power LED
HDD LED
2
LVDS LCD
Panel
GLAN 1
10
10
1
LPC
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
SIM
2
DDR4_2 SODIMM
5
2
GLAN 2
COM 6
1
PS/2 Power Select
(JP14)
1
1
(JP4)
1
1
Power LED
HDD LED
Reset
JP14
Front Panel
COM 5 6
10
14
30
EXC
9
12
1
2
LVDS LCD
Panel
GLAN 1
9
10
1
LPC
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
GLAN 2
3
2
1
DDR4_2 SODIMM
5
2
1
Buzzer
Power Button
USB 2.0 1
USB 9
10
bettery
PS/2 Power Select
(JP14)
1
1
(JP4)
1
2
1
Front Audio
1
bettery
Buzzer
Clear CMOS
Data (JP1)
12
Front Panel
Front Audio
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
-
If you encounter the following conditions, you can reconfigure the system with the default values stored in the ROM BIOS.
JP14 is used to select power for the PS/2 KB/MS connector (J20). Please refer to Chapter 5 for
detailed information on connectors.
a) CMOS data becomes corrupted.
Selecting +5V_standby will allow you to use USB devices to wake up the system.
b) You forgot the supervisor or user password.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power-off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set JP4 back to its default
setting, pins 1 and 2 On.
3. Now plug the power cord and power on the system.
17
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
COM1/COM2 RS232 Power Select
Clear CMOS
Data (JP1)
2
10
1
9
1
Buzzer
1
DIO
JP3
1
JP2
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
SIM
LPC
1
2
2
13
USB 1/2 USB 3.0
9
9
12
Front Panel
1
1
1
DIO
JP3
1
JP2
Power LED
HDD LED
9
Reset
(JP6)
6
SIM
9
2
2
1
(JP5)
6
2
DDR4_1 SODIMM
1
1
2
HDMI (default)/DP
2
1
1
29
(JP6)
6
SIM
1
4
SATA Power
1
3
1
10
4
2
1
JP8
1
1
2
COM 2
1
4
1
4
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
9
10
4
3
1
JP8
PCIe x4 (PCIE2)
2
1
1
1
STB_LED
PCIe x16 (PCIE1)
DC-in
9
COM 1
16
4-pin power
PWR_BTN_1
1
10
VGA
M.2 Type 2280
(PCIe)
2
1
1
1
2
6
2
1
6
1
9
10
2
2
1
1
(JP10) (JP16)
6
6
+
STB_LED
PCIe x16 (PCIE1)
SATA 3.0
SATA 1
SATA 0
DVI
16
+
1
DC-in
HDMI (default)/DP
COM 1
1
1
2
1
(JP11) (JP17) 9
6
6
10
4-pin power
1
10
COM 2
VGA
M.2 Type 2280
(PCIe)
1
2
COM 3
1
Mini PCIe 1
1
1
2
6
1
1
(JP12) (JP18)
6
6
21
COM 2
1
1
(JP9) (JP15)
6
6
COM 1
4
1
2
9
10
2
2
1
1
(JP10) (JP16)
6
6
DVI
10
1
9
JP7 (JP13) (JP19)
6
6
1
(JP5)
6
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
Reset
COM 4
USB 3/4 USB 3.0
COM 2
9
COM 6
2
COM 3
1
Mini PCIe 1
Power LED
HDD LED
USB 11-12
USB 2.0
1
1
10
1
2
9
COM 5 6
10
2
USB 3/4 USB 3.0
10
1
14
30
USB 1/2 USB 3.0
2
2
LVDS LCD
Panel
13
EXC
1
1
(JP12) (JP18)
6
6
21
1
LPC
GLAN 1
10
1
9
JP7 (JP13) (JP19)
6
6
29
10
SPI Flash
BIOS
1
COM 4
DDR4_2 SODIMM
5
2
GLAN 2
SIM
2
Power Button
USB 2.0
USB 13/14
USB 11-12
USB 2.0
1
DIO Power
1
USB 2.0 1
USB 9
Mini PCIe 2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
Buzzer
COM 6
14
30
EXC
1
1
LVDS LCD
Panel
GLAN 1
10
10
COM 5 6
2
10
DDR4_1 SODIMM
SPI Flash
BIOS
GLAN 2
2
2
1
Front Audio
1
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
1
Clear CMOS
Data (JP1)
12
Front Panel
Front Audio
1
DIO Power Source Select (Pins 0~7)
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
-
6
6
JP4
JP7
2
JP8
2
1
1
2
6
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
3
2
1
1
6
1-2
5V_Standby
1
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
3
2
1
2-3
5V
JP4 is used to configure the power of the DIO pins 0~7.
JP8 (for COM1) and JP7 (for COM2) are used to configure Serial COM ports to pure RS232 or
RS232 with power. The pin functions (Pin1 and Pin 9) of COM1 and COM2 will vary according
to JP8’s and JP7’s setting respectively.
18
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
RXD+
RXDTXD+
TXDN.C.
1 2345
2
10
1
9
12
1
9
1
LPC
1
2
2
COM 5 6
10
1
13
USB 1/2 USB 3.0
Reset
2
14
30
EXC
9
COM 6
USB 11-12
USB 2.0
1
LVDS LCD
Panel
GLAN 1
9
Power LED
HDD LED
2
DDR4_1 SODIMM
SPI Flash
BIOS
GLAN 2
SIM
10
10
COM 4
29
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
SIM
JP11, JP17
JP16 6
4
2
5
3
1
2
1
2
9
10
COM 3
1
Mini PCIe 1
1
10
COM 2
COM 2
HDMI (default)/DP
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
10
4
RS485
2
1
9
10
6
4
2
16
2
1
+
1
1
STB_LED
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
PCIe x16 (PCIE1)
2
1
9
-
COM1/COM2:
RS232/422/485
6
4
JP9, JP15 2
JP10
5
3
1
2
1
9
9
RS485
JP10 (for COM1) / JP16 (for COM2)
or
9
COM 1
678 9
RS422
Full Duplex
RS232
COM1/COM2:
RS232/422/485
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
4-pin power
DC-in
1
1
2
6
1
3
RS422
Full Duplex
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
RS232
DCD
TXD
GND
RTS
RI
USB 3/4 USB 3.0
1
2
6789
2
1
1
1
(JP12) (JP18)
6
6
21
2
1
(JP5)
6
6789
N.C.
N.C.
N.C.
N.C.
1
2
DATANC.
NC.
NC.
10
DATA+
TXD
NC.
NC.
NC.
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
N.C.
N.C.
N.C.
N.C.
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
PS/2 Power Select
(JP14)
1
DIO Power
1
RXDTXDNC.
NC.
DIO
RXD+
TXD+
NC.
NC.
NC.
1
JP3
1
JP2
DSRRTSCTSRI(or +5V)
Buzzer
1
(JP4)
1
bettery
1
1 2345
Front Panel
Front Audio
1
1 2345
RXD
DTR
DSR
CTS
Clear CMOS
Data (JP1)
DATA+
DATAN.C.
N.C.
N.C.
COM1 / COM2
DCD(or +12V)
RD
TD
DTRGND
COM1/COM2 RS232/422/485 Select
5
3
1
6
4
2
1-3, 4-6 On:
RS232 (default)
COM1:
RS232/422/485 Select
5
3
1
6
4
2
3-5, 4-6 On:
RS422 Full Duplex
5
3
1
3-5, 2-4 On:
RS485
JP9 and JP15 (for COM1) / JP11 and JP17 (for COM2)
6
4
2
5
3
1
1-3, 2-4 On:
RS232 (default)
These jumpers allow you to configure the Serial COM ports to RS232, RS422 (full duplex) or
RS485. JP9, JP10 and JP15 are used to configure Serial COM port 1; JP11, JP16 and JP17 are
used to configure Serial COM port 2. The pin assignments of COM port 1 and COM port 2 will
vary according to these jumpers’ settings. You can also configure the RS485 auto flow mechanism through the BIOS setup utility. For more information, please refer to Chapter 7.
6
4
2
5
3
1
3-5, 4-6 On:
RS422 Full Duplex/RS485
Note:
When COM1 RS232/422/485 is selected, JP9 and JP15 must be set in accordance to JP10. And when COM2 RS232/422/485 is selected, JP11 and JP17
must be set in accordance to JP16.
19
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
COM3/COM4 RS232/422/485 Select
RXD+
RXDTXD+
TXDN.C.
DCD
RD
TD
DTR
GND
1 2345
2
10
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
GLAN 2
SIM
LPC
1
2
2
13
EXC
Power LED
HDD LED
1
Reset
9
COM 6
USB 11-12
USB 2.0
1
2
14
30
USB 1/2 USB 3.0
9
COM 5 6
10
LVDS LCD
Panel
GLAN 1
10
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
2
10
6
4
2
5
3
1
678 9
6 78 9
JP6, JP19,
JP5
RS232
RS422
Full Duplex
RS485
COM 4
1
9
JP7 (JP13) (JP19)
6
6
29
(JP6)
6
SIM
COM3 / COM4
1
1
(JP12) (JP18)
6
6
21
1
10
1
2
9
10
COM 3
1
COM 2
COM 2
HDMI (default)/DP
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
2
6
1
3
4
1
2
10
1
JP8
+
STB_LED
PCIe x16 (PCIE1)
5
3
1
9
2
2
1
9
9
RS422
Full Duplex
2
1
6
1
2
1
9
RS232
COM 1
16
1
1
10
6
4
2
VGA
M.2 Type 2280
(PCIe)
4-pin power
DC-in
1
1
2
1
JP13
JP12, JP18
RXD+
TXD+
NC.
NC.
NC.
1
2
RXD
DTR
DSR
CTS
2
Mini PCIe 1
DCD
TXD
GND
RTS
RI
USB 3/4 USB 3.0
RXDTXDNC.
NC.
2
1
(JP5)
6
6 7 89
N.C.
N.C.
N.C.
N.C.
DIO
DATANC.
NC.
NC.
1
JP3
1
JP2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
1
1 23 4 5
1
DATA+
TXD
NC.
NC.
NC.
1
9
N.C.
N.C.
N.C.
N.C.
1
Buzzer
1 2 34 5
12
Front Panel
Front Audio
DSR
RTS
CTS
RI
Clear CMOS
Data (JP1)
DATA+
DATAN.C.
N.C.
N.C.
COM3 / COM4
PWR_BTN_1
1
RS485
JP13 (for COM3) / JP5 (for COM4)
PCIe x4 (PCIE2)
-
6
4
2
6
4
2
5
3
1
6
4
2
3-5, 4-6 On:
RS422 Full Duplex
1-3, 4-6 On:
RS232 (default)
These jumpers allow you to configure the Serial COM ports to RS232, RS422 (full duplex) or
RS485. JP12, JP13 and JP18 are used to configure Serial COM port 3; JP5, JP6 and JP19 are
used to configure Serial COM port 4. The pin assignments of COM port 3 and COM port 4 will
vary according to these jumpers’ settings. You can also configure the RS485 auto flow mechanism through the BIOS setup utility. For more information, please refer to Chapter 7.
5
3
1
5
3
1
3-5, 2-4 On:
RS485
JP12 and JP18 (for COM3) / JP6 and JP19 (for COM4)
6
4
2
Note:
When COM3 RS232/422/485 is selected, JP12 and JP18 must be set in accordance to JP13. And when COM4 RS232/422/485 is selected, JP6 and JP19 must
be set in accordance to JP5.
5
3
1
1-3, 2-4 On:
RS232 (default)
6
4
2
5
3
1
3-5, 4-6 On:
RS422 Full Duplex/RS485
20
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
DIO High/Low Select (DIO 0~3)
Clear CMOS
Data (JP1)
2
10
1
9
12
Buzzer
1
DIO
JP3
1
JP2
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
2
2
13
12
Front Panel
1
1
Buzzer
1
DIO
JP3
1
JP2
9
Power LED
HDD LED
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
9
Reset
USB 2.0
USB 13/14
1
9
JP7 (JP13) (JP19)
6
6
(JP6)
6
SIM
13
2
2
USB 1/2 USB 3.0
1
(JP5)
6
2
1
2
1
10
1
2
9
10
DDR4_1 SODIMM
1
1
1
4
1
4
2
29
(JP6)
6
1
10
1
JP8
HDMI (default)/DP
1
4
1
4
1
2
COM 2
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
9
COM 1
3
1
10
4
2
1
JP8
2
1
1
STB_LED
PCIe x16 (PCIE1)
DC-in
9
COM 1
16
4-pin power
PCIe x4 (PCIE2)
10
VGA
M.2 Type 2280
(PCIe)
1
PWR_BTN_1
1
1
1
2
6
+
+
PCIe x16 (PCIE1)
DC-in
6
9
10
2
2
1
1
(JP10) (JP16)
6
6
10
2
1
1
STB_LED
1
10
1
2
1
(JP11) (JP17) 9
6
6
1
DVI
16
4-pin power
1
1
2
COM 3
1
SATA 3.0
SATA 1
SATA 0
1
VGA
M.2 Type 2280
(PCIe)
2
1
1
(JP12) (JP18)
6
6
21
COM 2
1
1
2
6
1
2
Mini PCIe 1
1
1
(JP9) (JP15)
6
6
COM 1
4
10
1
9
JP7 (JP13) (JP19)
6
6
COM 2
SATA Power
3
Reset
COM 4
SIM
2
2
1
1
(JP10) (JP16)
6
6
DVI
9
COM 6
USB 3/4 USB 3.0
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
Power LED
HDD LED
USB 11-12
USB 2.0
1
1
(JP5)
6
COM 3
COM 2
HDMI (default)/DP
9
COM 5 6
10
2
1
Mini PCIe 1
10
1
2
2
USB 3/4 USB 3.0
2
14
30
EXC
1
1
(JP12) (JP18)
6
6
21
9
LVDS LCD
Panel
GLAN 1
10
COM 4
29
1
LPC
1
2
10
SPI Flash
BIOS
SIM
USB 11-12
USB 2.0
14
DDR4_2 SODIMM
5
2
GLAN 2
COM 6
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
10
1
1
30
EXC
USB 1/2 USB 3.0
9
COM 5 6
10
LVDS LCD
Panel
GLAN 1
10
2
DDR4_1 SODIMM
SPI Flash
BIOS
LPC
1
2
1
GLAN 2
SIM
1
PS/2 Power Select
(JP14)
1
1
(JP4)
1
2
1
Front Audio
1
bettery
1
Clear CMOS
Data (JP1)
Front Panel
Front Audio
1
DIO High/Low Select (DIO 4~7)
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
-
JP2
JP3
1 2 3
1-2 Pull-up
5V/5V_Standby
1 2 3
1 2 3
2-3 Pull-down
GND
1-2 Pull-up
5V/5V_Standby
JP3 is used to set the digital pins 0~3 to pull-up or pull-down.
1 2 3
2-3 Pull-down
GND
JP2 is used to set the digital pins 4~7 to pull-up or pull-down.
21
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
2
10
1
9
1
1
1
DIO
JP3
1
JP2
(1)
Power Button
USB 2.0
Status LED
HDD LED
Reset Switch
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
SIM
LPC
1
2
2
13
USB 1/2 USB 3.0
9
1
Reset
9
USB 2.0
COM 6
2
10
COM 4
29
(JP6)
6
SIM
USB 11/12
1
9
(JP13) (JP19)
6
6
JP7
2
1
1
1
(JP12) (JP18)
6
6
21
2
1
(JP5)
6
USB 3/4 USB 3.0
2
1
10
1
2
9
10
COM 3
1
Mini PCIe 1
1
2
COM 2
COM 2
HDMI (default)/DP
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
1
2
1
USB 2.0
USB 13/14
Power LED
HDD LED
USB 11-12
USB 2.0
1
14
30
EXC
10
1
COM 5 6
10
LVDS LCD
Panel
GLAN 1
2
2
DDR4_1 SODIMM
SPI Flash
BIOS
GLAN 2
COM 2 COM 1
Remote Power Switch
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
Buzzer
USB 2.0
USB 9
12
Front Panel
Front Audio
1
VCC
-Data1
+Data1
GND
N.C
Clear CMOS
Data (JP1)
2
10
9
VCC
-Data0
+Data0
GND
Key
Front Panel I/O Ports
VCC
-Data0
+Data0
GND
GND
USB Ports
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
Antenna holes
3
1
10
4
+
STB_LED
PCIe x16 (PCIE1)
9
16
2
1
1
1
10
COM 1
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
4-pin power
DC-in
1
1
2
6
1
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals. The system board is equipped with 2 USB
2.0 ports at the front panel I/O ports of the system unit. In addition, the system board provides 3 USB 2.0 ports via the internal pin headers.
The front panel I/O consists of the following ports:
•
•
•
•
•
•
Power button with LED
Remote power-on/off switch
Reset switch
Status and HDD LEDs
Two USB 2.0 ports
Two RS232/422/485 serial COM ports
•
BIOS Setting
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
22
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Rear Panel I/O Ports
COM (Serial) Ports
2
10
1
9
12
Front Panel
Front Audio
1
1
Buzzer
1
DIO
JP3
1
JP2
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
GLAN 2
SIM
LPC
1
2
2
13
USB 1/2 USB 3.0
1
9
Reset
COM 6
2
10
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
SIM
2
1
(JP5)
6
2
1
1
(JP12) (JP18)
6
6
21
1
2
1
10
1
2
9
10
COM 3
1
Mini PCIe 1
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
3
1
10
4
JP8
+
STB_LED
PCIe x16 (PCIE1)
10
1
9
Mic-in, Line-out
PoE 1~4
or
LAN 3~6
9
Expansion slot
COM 1
VGA
COM3
COM5
COM4
16
2
1
1
1
2
2
1
VGA
M.2 Type 2280
(PCIe)
2
4-pin power
DC-in
1
1
6
Digital IO
COM 2
COM 2
1
COM5, COM6:
RS232
COM 4
29
USB 3/4 USB 3.0
HDMI (default)/DP
DVI-D(1) HDMI(2)
(DVI-I connector)
USB 3.0
LAN1 LAN2
DC-in
Power LED
HDD LED
USB 11-12
USB 2.0
1
14
30
EXC
9
COM 5 6
10
LVDS LCD
Panel
GLAN 1
10
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
2
RXD
DTR
DSR
CTS
1
DCD
TXD
GND
RTS
RI
Clear CMOS
Data (JP1)
6
1
PCIe x4 (PCIE2)
2
PWR_BTN_1
1
COM1 to COM4:
RS232/RS422/RS485
-
The rear panel I/O consists of the following ports:
•
•
•
•
•
•
•
•
COM1 to COM4 can be selected among RS232/RS422/RS485 whereas COM5 and COM6 are
fixed at RS232. For pin definitions and jumper selection of different communication modes,
please refer to Chapter 4.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
•
9~36V DC-in
CFast card slot
DVI-D (DVI-I connector)/HDMI/VGA connectors
Line-out and microphone ports
Four USB 3.0 ports
Two RJ45 LAN ports & four PoE ports
Three COM ports
16-bit DIO connector
Notes:
BIOS Setting
1. This port can be in DVI-D or HDMI (HDMI available upon request).
2. This port is a DP/HDMI combo port but can only transmit either HDMI or DP signals (as indicated
on the panel). Please plug in a DP or an HDMI cable with the right orientation and alignment to
avoid damage to the connector. You should feel resistance (due to a pin on the right) if the cable is
not inserted correctly. For detailed instructions, see https://youtu.be/SUj07rfN5l8.
Configure the serial ports in the Advanced menu (“Super IO Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
Aligning side
(left)
Angled-corner
Angled-corner
pin
(up)
Align this edge with the
left side of the connector
23
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
RJ45 LAN Ports
Display Interfaces
2
Clear CMOS
Data (JP1)
10
1
1
1
9
1
Buzzer
1
DIO
JP3
1
JP2
LAN 2
1
LAN 1
10
1
9
2
2
USB 1/2 USB 3.0
2
10
1
9
1
9
29
2
1
2
1
10
1
2
9
10
1
4
2
10
1
JP8
+
1
STB_LED
PCIe x16 (PCIE1)
6
1
2
6
6
1
1
(JP4) (JP10)Reset
Clear CMOS
Data (JP1)
2
1
9
(JP9) (JP16)
6
6
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
1
1
1
(JP5) (JP12)
6
6
4
1
4
3
DC-in
2
PCIe x16 (PCIE1)
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
9
PWR_BTN_1
1
9
10
1
9
(JP7) (JP14)
6
6
System
Fan 2
1
1
10
1
2
COM 2
1
SATA Power
COM 1
1
2
COM 3
1
DVI-D
10
COM 4
LPC
10
2
1
1
DDR4_2 SODIMM
DVI
16
4-pin power
14
SATA 0
VGA
M.2 Type 2280
(PCIe)
9
System
Fan 1
HDMI (default)/DP
+
3
1
1
1
1
(JP8) (JP15)
6
6
1
1
1
2
1
Power Button
Power LED
HDD LED
SPI Flash
BIOS
2
HDMI
1
1
(JP9) (JP15)
6
6
COM 1
6
DC-in
USB 3-4 USB 3.0
2
1
1
(JP10) (JP16)
6
6
4
10
USB 1-2 USB 3.0
2
1
9
2
DDR4_1 SODIMM
1
COM 2
SATA Power
Auto Power-on
Select (JP11) 1
DIO Power
10
1
ECX
1
(JP11) (JP17) 9
6
6
1
COM 5
1
COM 3
SATA 3.0
SATA 1
25
2
bettery
10
COM 2
DVI
10
9
mSATA
1
1
(JP12) (JP18)
6
6
21
26
Front 1
Panel
LAN 1
1
Mini PCIe 1
4
1
Reset
1
9
(JP13) (JP19)
6
6
JP7
USB 3/4 USB 3.0
1
12
COM 6
COM 4
(JP6)
6
SATA 0
2
5 2
USB 2.0 9 1
USB 2.0 13-14 1
LAN 2
2
SIM
1
Parallel
2
1
5
COM 6
2
1
(JP5)
6
HDMI (default)/DP
9
Power LED
HDD LED
USB 11-12
USB 2.0
1
14
30
EXC
10
Mini PCIe
COM 5 6
10
LVDS LCD
Panel
13
DIO
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
LPC
GLAN 1
LAN 2
DDR4_2 SODIMM
5
2
GLAN 2
1
S/PDIF 1
Power Button
USB 2.0
USB 13/14
SIM
LAN 1
DIO Power
USB 2.0 1
USB 9
Mini PCIe 2
Buzzer
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
2
1
Front Audio
VGA
12
Front Panel
Front Audio
6
6
2 1
2 1
J21
6
2
16
JP3
JP2
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
PCIe x4 (PCIE2)
-
-
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
Features
DVI-D (DVI-I Connector) Port or HDMI
•
•
•
LAN 1: Intel® I219LM with iAMT11.0 PCIe (Intel® Core™ i3 processors do not support iAMT)
LAN 2: Intel® I211IT PCIe Gigabit Ethernet Controller
The DVI-D port is used to connect a digital LCD monitor to transmit uncompressed digital video.
This connector has a DVI-I receptacle but implements DVI-D signals (digital only).
Connect the display device’s cable connector to the DVI-D port. After you plug the cable connector into the DVI-D port, gently tighten the cable screws to hold the connector in place. You can
choose this port to be either DVI-D or HDMI.
The LAN ports allow the system board to connect to a local area network with a network hub.
BIOS Setting
HDMI Port or DisplayPort
Configure the onboard LAN in the Advanced menu (“ACPI Configuration”) of the BIOS. Refer to
Chapter 7 for more information.
The HDMI port which carries both digital audio and video signals is used to connect a LCD
monitor or digital TV that has the HDMI port. You can choose this port to be either HDMI or DP.
Driver Installation
BIOS Setting
Install the LAN drivers. Refer to Chapter 8 for more information.
Configure the display devices in the Advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to the Chapter 7 for more information.
Driver Installation
Install the graphics driver. Refer to Chapter 8 for more information.
24
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
USB Ports
9~36V DC-in
Clear CMOS
Data (JP1)
2
10
1
9
12
Front Panel
Front Audio
1
1
Buzzer
DIO
JP3
1
JP2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
1
DIO Power
1
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
GLAN 2
LPC
1
2
2
13
USB 1/2 USB 3.0
1
2
(JP6)
6
1
(JP5)
6
USB 3/4 USB 3.0
2
1
10
1
2
9
10
1
2
USB 1/2 USB 3.0
4
4
1
1
10
4
2
1
JP8
HDMI (default)/DP
+
PCIe x16 (PCIE1)
6
1
2
10
1
9
(JP13) (JP19)
6
6
JP7
1
1
(JP12) (JP18)
6
6
21
2
1
2
1
10
1
2
9
10
COM 3
1
1
COM 2
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
1
6
9
2
10
1
9
COM 1
1
3
-
PWR_BTN_1
1
PCIe x4 (PCIE2)
1
10
4
JP8
DC-in
16
DC-in
2
1
1
1
STB_LED
PCIe x16 (PCIE1)
COM 1
VGA
M.2 Type 2280
(PCIe)
2
4-pin power
+
DC-in
2
COM 4
29
(JP6)
6
10
2
1
1
STB_LED
Reset
COM 2
16
4-pin power
1
9
14
Mini PCIe 1
VGA
M.2 Type 2280
(PCIe)
1
Power LED
HDD LED
COM 6
USB 3/4 USB 3.0
1
1
2
9
USB 11-12
USB 2.0
1
SIM
1
1
(JP9) (JP15)
6
6
COM 1
6
3
DDR4_1 SODIMM
1
(JP5)
6
2
SATA Power
10
1
2
+
1
1
2
2
30
EXC
1
1
(JP10) (JP16)
6
6
DVI
9
2
COM 5 6
2
10
LVDS LCD
Panel
13
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
1
LPC
GLAN 1
COM 2
COM 2
HDMI (default)/DP
10
COM 3
1
Mini PCIe 1
1
2
DDR4_2 SODIMM
5
2
SPI Flash
BIOS
10
1
1
(JP12) (JP18)
6
6
21
Power Button
USB 2.0 1
USB 9
1
1
9
(JP13) (JP19)
6
6
JP7
DIO Power
1
USB 2.0
USB 13/14
SIM
COM 4
29
DIO
PS/2 Power Select
(JP14)
1
1
(JP4)
1
JP3
1
JP2
GLAN 2
2
USB 3-4
Front Panel
1
Reset
9
USB 11-12
USB 2.0
1
12
1
Mini PCIe 2
COM 6
SIM
USB 1-2
9
COM 5 6
10
14
30
EXC
9
1
Buzzer
Power LED
HDD LED
10
bettery
2
LVDS LCD
Panel
GLAN 1
10
1
DDR4_1 SODIMM
SPI Flash
BIOS
SIM
2
2
1
Front Audio
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
USB 3.0
Clear CMOS
Data (JP1)
1
bettery
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals. The system board is equipped with 4 USB
3.0 ports at the rear panel and 2 USB 2.0 ports at the front panel of the system unit.
•
This jack provides a maximum of 160W power input solution. Connect a DC power cord to this
jack. Using a voltage higher than the recommended one may fail to boot the system or cause
damage to the system board.
BIOS Setting
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
25
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
I/O Connectors
SATA (Serial ATA) Connectors
PS/2 KB/MS Connector
Clear CMOS
Data (JP1)
1
10
1
1
9
1
Buzzer
1
DIO
DIO Power
1
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
LPC
1
13
2
2
USB 1/2 USB 3.0
2
10
1
9
1
Power Button
USB 2.0
USB 13/14
9
10
(JP6)
6
2
2
USB 3/4 USB 3.0
2
1
1
2
HDMI (default)/DP
2
(JP6)
6
SIM
9
10
2
1
4
DVI
9
10
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
1
1
(JP9) (JP15)
6
6
COM 1
1
10
3
4
1
2
10
1
JP8
10
2
1
JP8
+
PCIe x16 (PCIE1)
STB_LED
6
1
2
PWR_BTN_1
1
PCIe x16 (PCIE1)
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
DC-in
DC-in
2
1
1
STB_LED
2
1
1
1
16
4-pin power
1
9
COM 1
VGA
M.2 Type 2280
(PCIe)
SATA 3.0 6Gb/s
9
COM 1
16
+
1
10
4
7
1
VGA
M.2 Type 2280
(PCIe)
4-pin power
1
3
1
1
2
6
SATA 0/1
COM 2
SATA Power
1
1
2
6
1
10
1
2
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
2
COM 3
1
COM 2
2
1
1
(JP10) (JP16)
6
6
4
1
1
(JP12) (JP18)
6
6
21
COM 2
2
1
10
1
9
JP7 (JP13) (JP19)
6
6
Mini PCIe 1
1
(JP11) (JP17) 9
6
6
1
1
Reset
COM 4
29
USB 3/4 USB 3.0
HDMI (default)/DP
COM 2
SATA 3.0
SATA 1
SATA 0
9
COM 6
1
(JP5)
6
COM 3
1
Mini PCIe 1
Power LED
HDD LED
USB 11-12
USB 2.0
1
14
30
1
10
1
2
9
COM 5 6
10
2
1
(JP5)
6
10
1
2
1
1
(JP12) (JP18)
6
6
21
2
2
DDR4_1 SODIMM
1
9
(JP13) (JP19)
6
6
JP7
SIM
13
USB 1/2 USB 3.0
COM 4
29
9
LVDS LCD
Panel
GLAN 1
EXC
2
1
LPC
1
USB 11-12
USB 2.0
1
10
SPI Flash
BIOS
SIM
Reset
DDR4_2 SODIMM
5
2
GLAN 2
Power LED
HDD LED
COM 6
14
30
EXC
DIO Power
1
USB 2.0 1
USB 9
Mini PCIe 2
COM 5 6
10
LVDS LCD
Panel
GLAN 1
DIO
PS/2 Power Select
(JP14)
1
1
(JP4)
1
1
JP3
1
JP2
2
DDR4_1 SODIMM
SPI Flash
BIOS
GLAN 2
SIM
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
12
Front Panel
PS/2 Power Select
(JP14)
1
1
(JP4)
1
JP3
1
JP2
1
Buzzer
1
bettery
9
bettery
12
Front Panel
Front Audio
10
GND
TXP
TXN
GND
RXN
RXP
GND
2
Clear CMOS
Data (JP1)
2
1
Front Audio
PCIe x4 (PCIE2)
-
Features
PS/2 Mouse Power 10 9
(5V/5V_Standby)
GND (w/BEAD)
GND
PS/2 Mouse DATA
PS/2 Mouse CLK
2 1
PS/2 Keyboard Power
(5V/5V_Standby)
NC (Key)
GND
PS/2 Keyboard DATA
PS/2 Keyboard CLK
•
2 Serial ATA 3.0 ports
- SATA port 0 and 1 with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
The Serial ATA connectors are used to connect the Serial ATA device. Connect one end of the
Serial ATA data cable to a SATA connector on the system board and the other end to your
Serial ATA device.
The 10-pin connector is used to connect PS/2 keyboard and mouse.
The power cable must be connected from the system board’s Serial ATA power connector to
the SATA drive’s power connector in order to provide power to the drive.
BIOS Setting
Configure the Serial ATA drives in the Advanced submenu (“SATA Configuration” section) of the
BIOS. Refer to Chapter 7 for more information.
26
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
SATA (Serial ATA) Power Connectors
Clear CMOS
Data (JP1)
2
10
1
9
12
1
Buzzer
1
DIO
JP3
1
JP2
DIO Power
1
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
1
9
LPC
1
2
2
13
1
USB 1/2 USB 3.0
Front Panel
9
SIM
13
USB 1/2 USB 3.0
1
2
1
10
1
2
9
10
2
2
1
1
(JP10) (JP16)
6
6
1
1
(JP9) (JP15)
6
6
COM 1
10
4
JP8
1
2
PCIe x16 (PCIE1)
6
1
2
1
2
1
10
1
2
9
10
COM 3
1
COM 2
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
1
2
1
4
1
4
1
1
(JP9) (JP15)
6
6
COM 1
1
3
1
10
4
DC-in
9
1
JP8
4
PCIe x4 (PCIE2)
-
These SATA power connectors supply power to the SATA drives. Connect one end of the provided power cable to the SATA power connector and the other end to your storage device.
10
1
9
COM 1
16
2
1
1
STB_LED
PCIe x16 (PCIE1)
2
VGA
M.2 Type 2280
(PCIe)
2
4-pin power
COM 1
1
1
6
1
PWR_BTN_1
1
2
6
1
PCIe x4 (PCIE2)
2
PWR_BTN_1
1
SMBus
2
1
6
5
SMBUS_Alert
SMBUS Clock
+3.3V_standby
STB_LED
1
1
(JP12) (JP18)
6
6
21
SATA Power
-
+
1
SATA
Power 0/1
10
2
1
1
(JP6)
6
1
1
(JP10) (JP16)
6
6
16
4-pin power
DC-in
1
9
(JP13) (JP19)
6
6
JP7
SIM
DVI
VGA
M.2 Type 2280
(PCIe)
2
1
10
COM 4
29
+
2
6
1
1
2
14
COM 2
1
Reset
9
COM 6
COM 2
HDMI (default)/DP
SATA Power
3
1
Mini PCIe 1
1
(JP11) (JP17) 9
6
6
1
Power LED
HDD LED
USB 11-12
USB 2.0
1
USB 3/4 USB 3.0
COM 3
1
COM 2
4
DDR4_1 SODIMM
1
(JP5)
6
1
1
(JP12) (JP18)
6
6
21
SATA 3.0
SATA 1
4
9
COM 5 6
10
2
2
+12V
Ground
Ground
+5V
2
Mini PCIe 1
1
2
2
10
1
NC
SMBUS Data
GND
USB 3/4 USB 3.0
1
9
30
EXC
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
DVI
1
2
COM 4
29
1
(JP5)
6
1
10
LVDS LCD
Panel
GLAN 1
10
DDR4_2 SODIMM
5
2
LPC
1
2
SIM
SATA 0
Power Button
USB 2.0 1
USB 9
USB 2.0
USB 13/14
GLAN 2
Reset
USB 11-12
USB 2.0
1
DIO Power
1
SPI Flash
BIOS
2
HDMI (default)/DP
DIO
JP3
1
JP2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
1
COM 6
14
30
EXC
1
Mini PCIe 2
COM 5 6
10
LVDS LCD
Panel
GLAN 1
9
12
1
Power LED
HDD LED
2
DDR4_1 SODIMM
SPI Flash
BIOS
9
10
1
GLAN 2
SIM
2
10
10
bettery
Buzzer
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
2
1
Front Audio
1
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
1
Clear CMOS
Data (JP1)
Front Panel
Front Audio
1
SMBus Connector
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
27
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Rear Audio Connector
Digital I/O Connector & DIO Power
Clear CMOS
Data (JP1)
2
10
1
9
1
1
1
DIO
JP3
1
JP2
GND
NC
Mic-JD
NC
Line-JD
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
9
LPC
1
2
2
13
1
DIO
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
Power LED
HDD LED
1
9
USB 2.0
USB 13/14
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
13
SIM
2
2
USB 3/4 USB 3.0
2
1
2
1
10
1
2
9
10
1
Line-out
1
1
4
1
4
DVI
29
6
1
3
2
10
4
HDMI (default)/DP
6
1
2
1
2
9
10
COM 2
1
(JP11) (JP17) 9
6
6
4
1
4
2
2
1
1
(JP10) (JP16)
6
6
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
4
COM 1
1
1
1
2
6
1
3
10
4
10
9
COM 1
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
16
4-pin power
1
PWR_BTN_1
1
STB_LED
PCIe x16 (PCIE1)
DC-in
PCIe x4 (PCIE2)
2
1
1
+
+
DC-in
9
1
DVI
2
1
1
STB_LED
PCIe x16 (PCIE1)
10
1
1
10
COM 3
1
1
1
16
4-pin power
1
2
1
2
COM 2
SATA 3.0
SATA 1
SATA 0
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
1
1
1
(JP12) (JP18)
6
6
21
1
Mini PCIe 1
1
1
10
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
USB 3/4 USB 3.0
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
DIO
2
COM 4
2
2
1
1
(JP10) (JP16)
6
6
1
Reset
9
USB 11-12
USB 2.0
1
1
(JP5)
6
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
DIO
Power
Power LED
HDD LED
COM 6
SIM
COM 2
COM 2
9
COM 5 6
10
2
DDR4_1 SODIMM
2
COM 3
1
Mini PCIe 1
10
1
+5V
5V_STB
GND
+12V
Mic-L
Mic-R
Line-R
GND
Line-L
1
(JP5)
6
2
14
30
EXC
USB 1/2 USB 3.0
1
1
(JP12) (JP18)
6
6
21
9
LVDS LCD
Panel
GLAN 1
10
COM 4
29
10
1
LPC
1
2
2
SPI Flash
BIOS
SIM
USB 11-12
USB 2.0
1
DDR4_2 SODIMM
5
GLAN 2
Reset
COM 6
PS/2 Power Select
(JP14)
1
1
(JP4)
1
JP3
1
JP2
2
HDMI (default)/DP
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
DIO0
DIO2 DIO4
DIO6
8
1
DIO1
-
-
Rear Panel
Front Panel
1
COM 5 6
10
14
30
EXC
USB 1/2 USB 3.0
9
12
1
2
DDR4_1 SODIMM
LVDS LCD
Panel
GLAN 1
9
10
1
1
SPI Flash
BIOS
SIM
2
10
10
bettery
Buzzer
Power Button
GLAN 2
10
9
Mic-in
1
USB 2.0 1
USB 9
Mini PCIe 2
2
1
DIO Power
2
1
Front Audio
1
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
Buzzer
Clear CMOS
Data (JP1)
12
Front Panel
Front Audio
1
DIO5
DIO3
DIO7
The 8-bit Digital I/O connector provides 8-bit digital input/output signals to provide the ability
to monitor and control the states of the connected external devices.
Digital I/O Connector
Rear Audio
The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
•
•
Line-out Jack
This jack is used to connect a headphone or external speakers.
Mic-in Jack
This jack is used to connect an external microphone.
Driver Installation
Install the audio driver. Refer to the Chapter 8 for more information.
Digital I/O Power
Pins
Function
Pins
Function
1
DIO 0
1
+12V
2
DIO 1
2
GND
3
DIO 2
3
5V_Standby
4
DIO 3
4
5V
5
DIO 4
6
DIO 5
7
DIO 6
8
DIO 7
28
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Front Panel Connector
12V DC-out
Clear CMOS
Data (JP1)
1
Clear CMOS
Data (JP1)
2
10
1
9
12
1
1
Buzzer
1
DIO
JP3
1
JP2
DIO Power
1
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
LPC
2
2
13
9
Power LED
HDD LED
1
9
2
10
1
2
1
2
4
SATA Power
4
2
10
1
JP8
+
PCIe x16 (PCIE1)
2
3
4
1
2
1
1
2
6
10
10
1
JP8
10
9
COM 1
VGA
M.2 Type 2280
(PCIe)
16
4-pin power
9
COM 1
2
1
1
1
STB_LED
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
PCIe x16 (PCIE1)
DC-in
6
1
PWR_BTN_1
1
PCIe x4 (PCIE2)
HDD-LED - HDD LED
-
3
1
1
(JP9) (JP15)
6
6
COM 1
-
DC-in
6
1
4
1
2
1
1
STB_LED
COM 2
SATA Power
16
4-pin power
1
4
1
DVI
VGA
M.2 Type 2280
(PCIe)
9
10
2
2
1
1
(JP10) (JP16)
6
6
1
+
3
1
1
10
1
2
1
(JP11) (JP17) 9
6
6
1
1
1
1
2
6
1
1
2
COM 3
1
COM 2
1
1
(JP9) (JP15)
6
6
COM 1
DC-out
1
1
(JP12) (JP18)
6
6
21
SATA 3.0
SATA 1
SATA 0
1
(JP11) (JP17) 9
6
6
4
1
(JP6)
6
HDD-LED
RESET-SW
1
9
(JP13) (JP19)
6
6
JP7
4
This LED will be lit when the hard drive is being accessed.
12V2
12V1
RESET SW - Reset Switch
GND1
GND2
This switch allows you to reboot without having to power off the system.
1
12
11
10
COM 4
29
Mini PCIe 1
HDMI (default)/DP
2
1
Reset
2
14
2
1
(JP5)
6
2
2
1
1
(JP10) (JP16)
6
6
DVI
9
COM 6
COM 2
COM 2
1
1
USB 11-12
USB 2.0
1
USB 3/4 USB 3.0
9
10
ATX-SW
PWR-LED
COM 5 6
10
SIM
COM 3
SATA 3.0
SATA 1
SATA 0
2
2
9
Power LED
HDD LED
2
DDR4_1 SODIMM
1
10
1
2
10
1
30
USB 1/2 USB 3.0
1
1
(JP12) (JP18)
6
6
21
1
Mini PCIe 1
9
2
LVDS LCD
Panel
13
EXC
1
9
JP7 (JP13) (JP19)
6
6
USB 3/4 USB 3.0
1
LPC
GLAN 1
2
(JP6)
6
10
Reset
COM 4
1
(JP5)
6
1
USB 2.0
USB 13/14
SIM
COM 6
29
Power Button
DDR4_2 SODIMM
5
2
GLAN 2
USB 11-12
USB 2.0
SIM
DIO Power
1
SPI Flash
BIOS
2
HDMI (default)/DP
DIO
USB 2.0 1
USB 9
1
14
30
EXC
USB 1/2 USB 3.0
1
JP3
1
JP2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
Mini PCIe 2
COM 5 6
10
LVDS LCD
Panel
GLAN 1
Front Panel
2
1
Front Panel
12
1
10
1
GLAN 2
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
SIM
9
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
1
Buzzer
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
10
bettery
Front Panel
Front Audio
1
2
1
Front Audio
2
ATX-SW - ATX Power Switch
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power
On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To
RAM) state, it will blink every 4 seconds.
The 4-pin vertical type connector (optional) provides low power output.
Pin Pin Assignment
HDD-LED
RESET SW
3
HDD Power
5
Signal
7
Ground
9
RST Signal
11
N.C.
Pin Pin Assignment
2
LED Power
PWR-LED 4
LED Power
ATX-SW
6
Signal
8
Ground
10
Signal
29
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Expansion Slots
EXC Slot
The EXC interface is used to install an EXC card for I/O expansion via a daughter board.
Clear CMOS
Data (JP1)
2
10
1
9
1
1
1
DIO
JP3
1
JP2
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
Buzzer
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
SIM
LPC
1
2
2
13
USB 1/2 USB 3.0
9
Power LED
HDD LED
1
Reset
9
COM 6
USB 11-12
USB 2.0
1
2
14
30
EXC
10
1
COM 5 6
10
LVDS LCD
Panel
GLAN 1
2
2
DDR4_1 SODIMM
SPI Flash
BIOS
GLAN 2
10
COM 4
29
1
9
(JP13) (JP19)
6
6
JP7
(JP6)
6
SIM
2
1
(JP5)
6
USB 3/4 USB 3.0
EXC
2
1
2
1
10
1
2
9
10
COM 3
COM 2
COM 2
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
SATA 0
1
1
Mini PCI Express
Slot (with SIM card)
1
1
(JP12) (JP18)
6
6
21
1
Mini PCIe 1
HDMI (default)/DP
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
12
Front Panel
Front Audio
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
3
1
10
4
10
9
COM 1
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
16
4-pin power
2
1
+
1
1
STB_LED
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
PCIe x16 (PCIE1)
DC-in
1
1
2
6
1
-
PCI Express x16
PCI Express x4
Dual Mini PCIe Slots (with Mini SIM Card Slots)
The Mini PCIe socket is used to install a Mini PCIe card. The system is equipped with two
full-size (or half-size) Mini PCIe slot slots (Mini PCIe 1: PCIe & USB signals; Mini PCIe 2:
USB signals only).
PCI Express x16 Slot
Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into
the PCI Express x16 slot such as a graphics card.
PCI Express x4 Slot
Install PCI Express cards such as network cards or other cards that comply to the PCI Express specifications into this slot.
Pin Assignment
GND
PCIE_ECX_RX1p
PCIE_ECX_RX1n
PCIE_ECX_TX1n
PCIE_ECX_TX1p
CLK_PCIE_ECX1_p
CLK_PCIE_ECX1_n
Reserved
Reserved
GND
CLK_PCIE_ECX3_p
CLK_PCIE_ECX3_n
GND
SATA_LED#
EDP_AUX_n (N/A)
EDP_AUX_p (N/A)
Intel Control Link Bus
Intel Control Link Bus
Intel Control Link Bus
GND
EDP_LAN0_n
EDP_LAN0_p
EDP_LAN1_n
EDP_LAN1_p
EDP_LAN2_n
EDP_LAN2_p
DPC_AUX_n (N/A)
DPC_AUX_p (N/A)
EDP_HPD
GND
EDP_LAN3_n
EDP_LAN3_p
DPB_CTRL_CLK (N/A)
DPB_CTRL_DATA (N/A)
DPC_CTRL_CLK (N/A)
DPC_CTRL_DATA (N/A)
Reserved
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
Pin Assignment
GND
PCIE_ECX_RX2p
PCIE_ECX_RX2n
PCIE_ECX_TX2n
PCIE_ECX_TX2p
CLK_PCIE_ECX2_p
CLK_PCIE_ECX2_n
Reserved
Reserved
GND
PCIE_ECX_RX5p (N/A)
PCIE_ECX_RX5n (N/A)
PCIE_ECX_TX5n (N/A)
PCIE_ECX_TX5p (N/A)
CLK_PCIE_ECX5_p (N/A)
CLK_PCIE_ECX5_n (N/A)
Reserved
Reserved
HD_OUT (N/A)
GND
PCIE_ECX_RX4p
PCIE_ECX_RX4n
PCIE_ECX_TX4n
PCIE_ECX_TX4p
CLK_PCIE_ECX4_p
CLK_PCIE_ECX4_n
Reserved
Reserved
Reserved
GND
LPC_FRAME#
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
LPC_LDRQ1#
DPC_HPD (N/A)
30
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
LPC Connector
CLK_LPC
HD_SPKR (N/A)
GND
USB3_RX0n
USB3_RX0p
GND
USB3_TX0n
USB3_TX0p
GND
HD_BITCLK (N/A)
HD_SYNC (N/A)
HD_SIN (N/A)
GND
USB3_RX1n
USB3_RX1p
GND
USB3_TX1n
USB3_TX1p
GND
SATA_TXn
SATA_TXp
Reserved
GND
GND
DFI Board ID_0
DFI Board ID_1
DFI Board ID_2
SATA_RXn
SATA_RXp
VIN
+5VDU
+5VDU
GND
+3.3V
+3.3V
+3.3V
+3.3V
GND
+5V
+5V
+5V
+5V
+5V
Clear CMOS
Data (JP1)
2
10
1
9
12
Front Panel
Front Audio
1
1
1
Buzzer
1
DIO
JP3
1
JP2
DIO Power
1
Power Button
USB 2.0 1
USB 9
Mini PCIe 2
PS/2 Power Select
(JP14)
1
1
(JP4)
1
bettery
USB 2.0
USB 13/14
DDR4_2 SODIMM
5
2
10
1
9
GLAN 2
SIM
LPC
1
13
2
2
1
USB 1/2 USB 3.0
Power LED
HDD LED
9
Reset
USB 11-12
USB 2.0
1
2
(JP6)
6
1
(JP5)
6
USB 3/4 USB 3.0
2
1
1
(JP12) (JP18)
6
6
21
1
2
1
10
1
2
9
10
COM 2
COM 2
1
(JP11) (JP17) 9
6
6
SATA 3.0
SATA 1
1
2
2
1
1
(JP10) (JP16)
6
6
1
4
1
4
DVI
1
1
(JP9) (JP15)
6
6
COM 1
SATA Power
1
1
10
4
9
16
2
1
1
STB_LED
PCIe x16 (PCIE1)
10
COM 1
VGA
M.2 Type 2280
(PCIe)
2
1
JP8
4-pin power
1
DC-in
1
1
2
6
3
14
COM 3
1
Mini PCIe 1
SATA 0
13
10
1
9
(JP13) (JP19)
6
6
JP7
SIM
1
2
COM 4
29
2
HDMI (default)/DP
1
LPC
COM 6
14
30
EXC
9
COM 5 6
10
LVDS LCD
Panel
GLAN 1
10
1
2
DDR4_1 SODIMM
SPI Flash
BIOS
2
6
1
2
PWR_BTN_1
1
PCIe x4 (PCIE2)
-
PLT-RST#
HD_RST# (N/A)
GND
DPC_LAN0_n (N/A)
DPC_LAN0_p (N/A)
DPC_LAN1_n (N/A)
DPC_LAN1_p (N/A)
DPC_LAN2_n (N/A)
DPC_LAN2_p (N/A)
DPC_LAN3_n (N/A)
DPC_LAN3_p (N/A)
USB_PWR_SEL
GND
USB_1P
USB_1N
USB_0P
USB_0N
USB_OC#
PCIE_ECX_RX3p
PCIE_ECX_RX3n
PCIE_ECX_TX3n
PCIE_ECX_TX3p
GND
BID
SMB_CLK_RESUME
SMB_DATA_RESUME
INT_GPIO#
PCIe_Wake#
INT_SERIRQ
VIN
+3.3VDU
+3.3VDU
GND
+12V
+12V
+12V
+12V
GND
+5V
+5V
+5V
+5V
+5V
+
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
157
159
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition
towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components
within the system, which are typically provided by a Super I/O controller. Furthermore, it can be
used to interface firmware hubs, Trusted Platform Module (TPM) devices and embedded controller solutions. Data transfer on the LPC bus is implemented over a 4 bit serialized data interface,
which uses a 24MHz LPC bus clock. For more information about LPC bus refer to the Intel® Low
Pin Count Interface Specification Revision 1.1’. The table below indicates the pin fuctions of the
LPC connector.
Pin
1
3
5
7
9
11
13
Pin Assignment
L_CLK
L_RST#
L_FRAME#
L_AD3
L_AD2
INT_SERIRQ
5VSB
Pin
2
4
6
8
10
12
14
Pin Assignment
L_AD1
L_AD0
3V3
GND
Kev
GND
5V
31
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
LAN Ports (daughter board)
Digital I/O Connector (daughter board)
ACT/Link or
PoE LED
G G 8 76 543 21
Speed LED
LAN 3~6 or PoE 1~4:
Intel I210IT
DIO
DIO
CN3
CN4
CN5
CN2
20
10
U17
U15
U14
U16
1
LAN4
JP3
1
1
JP51
1
1
LAN3
LAN2
LAN1
G G 8 76 543 21
3
3 JP1
3
3 JP4
3
DIO
CN3
CN4
CN5
CN2
20
10
1
U15
U17
U14
U16
JP2
LAN4
DC_IN
4
3
2
1
JP3
1
1
JP51
1
1
CN7
LAN3
LAN2
LAN1
3
3 JP1
3
3 JP4
3
JP2
DC_IN
4
3
2
1
CN7
Activity/Link LED
LED Behavior
Off
Blinking
On
Description
No link
Data Activity
Link
Speed LED
LED Behavior
Off
Green
Orange
Description
10Mbps connection
100Mbps connection
1Gbps connection
The Digital I/O connector provides 16 digital inputs or outputs to enable monitor and control of
the state of the connected external devices. You can use the provided HW Utility to config­ure a
port to be either input or output. Please refer to Chapter 8 for more information.
Digital I/O Connector
Pins
DIO-A
DIO-B
1
DIO1
DIO1
2
DIO2
DIO2
3
DIO3
DIO3
4
DIO4
DIO4
LAN3 to LAN6 can be normal Gigabit ports or PoE (Power over Ethernet) ports. With PoE
(Power over Ethernet) support, the ports carry power to connected devices without the need
for individual power supplies. Each port delivers up to 15.4 Watts of power to the connected
devices that comply with IEEE 802.3af, for example, access points and VoIP phones.
5
DIO5
DIO5
6
DIO6
DIO6
7
DIO7
DIO7
Driver Installation
8
DIO8
DIO8
G
GND
GND
G
GND
GND
PoE LED
LED Behavior
Off
Speed LED
LED Behavior Description
Off
10Mbps connection
DFI INC.
SILK_TOP
MODEL:
XCT3-4LPSEGD
DATE:
08/22/2017
REV:
A
Green
Description
The system is not
powered on.
Supplying power over Green
the Ethernet link
Orange
DFI INC.
100Mbps connection
SILK_TOP
1Gbps connection
Install the LAN driver. Refer to Chapter 8 for more information.
MODEL:
XCT3-4LPSEGD
DATE:
08/22/2017
REV:
A
32
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 6
Chapter 6 - Mounting Options
2. Use the provided mounting screws to secure the wall mount brackets on each side of the
system unit.
Wall Mount
The wall mount kit includes the following:
•
•
2 Wall mount brackets
4 Bracket screws
Mounting screw
Wall mount
bracket
Wall mount
bracket
Mounting screw
The following illustration shows the location and dimension of the holes for mounting the device
onto a wall or rack .
1. The wall mounting holes are located on the bottom of the system unit.
Mounting hole
Ø8.50
80
120
16
5
6
Ø3.60
4
251.80
262.80
Mounting hole
35
Chapter 6 Mounting Options
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising