Dfi VC70B-KU Manual
VC70B-KU
User’s Manual
A52700931
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2019. All Rights Reserved.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Copyright........................................................................................ 2
Front Panel I/O Ports...............................................................................................16
Trademarks..................................................................................... 2
Rear Panel I/O Ports.................................................................................................16
About this Manual....................................................................... 4
Display Interfaces................................................................................................................................... 17
USB Ports................................................................................................................................................... 18
COM (Serial) Ports.................................................................................................................................. 19
RJ45 LAN Ports........................................................................................................................................ 20
Audio .......................................................................................................................................................... 20
Warranty ......................................................................................... 4
I/O Connectors..........................................................................................................21
FCC and DOC Statement on Class A..................................... 2
Serial ATA Connector & Serial ATA Power Connector............................................................... 21
Expansion Slots....................................................................................................................................... 21
Front Panel Connector.......................................................................................................................... 22
Standby Power LED............................................................................................................................... 23
Battery........................................................................................................................................................ 23
Static Electricity Precautions.................................................... 4
Safety Measures............................................................................ 4
Safety Precautions....................................................................... 5
Chapter 6 - Mounting Options............................................... 25
About the Package...................................................................... 5
Chapter 7 - BIOS Setup.............................................................. 28
Chapter 1 - Introduction........................................................... 6
Main............................................................................................................................................................. 29
Advanced ................................................................................................................................................. 29
UEFI Device Manager............................................................................................................................ 35
Security....................................................................................................................................................... 41
Boot............................................................................................................................................................. 42
Exit................................................................................................................................................................ 43
Overview........................................................................................................................ 6
Key Features................................................................................................................. 6
Specifications............................................................................................................... 7
Chapter 8 - Supported Software............................................ 45
Getting to Know the VC70B-KU............................................................................ 8
Chapter 9 - Intel AMT Settings .............................................. 52
Mechanical Dimensions........................................................................................... 9
Chapter 2 - Getting Started...................................................... 10
Chapter 3 - Installing the Devices......................................... 11
Removing the Chassis Cover................................................................................11
Installing a SATA Drive............................................................................................11
Installing a Mini PCIe Card....................................................................................12
Chapter 4 - Jumper Settings.................................................... 14
Clear CMOS Data......................................................................................................14
Auto Power-on Select.............................................................................................14
Mini PCIe/SATA Signal Select...............................................................................15
COM4/DIO Select......................................................................................................15
Chapter 5 - Ports and Connectors......................................... 16
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The auto-run screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
We will not be liable for any indirect, special, incidental or damages to the product that
has been modified or altered.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 VC70B-KU system unit
• Mounting screws for M.2 and Mini PCIe modules
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
Optional Items
• Dispose of used batteries according to local ordinance.
• Wall Mount kit
• Power Cord
• Power Adapter: 120W, 19V/6.31A or 60W, 19V/3.15A
• Keep this system away from humidity.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview
Front View
Model Name
VC70B-KU
Processor
7th Generation Intel® CoreTM processors, BGA 1356
LAN
Two LAN ports
COM
Six COM ports
Display
VGA & HDMI
Audio
Microphone and Line-out
USB
Four USB 3.0 & two USB 2.0 Type A ports
Power
9~36V DC-in
DIO/CAN bus
8-bit DIO or CAN bus with a DB9 connector (selection via jumper settings)
Power Switch
Power-on button
Rear View
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
Processor
7th Generation Intel® CoreTM Processors, BGA 1356
Intel® CoreTM i7-7600U Processor, Dual Core, 4M Cache, 2.8 GHz, 15W
Intel® CoreTM i5-7300U Processor, Dual Core, 3M Cache, 2.6 GHz, 15W
Intel® CoreTM i3-7100U Processor, Dual Core, 3M Cache, 2.4 GHz, 15W
Memory
• Supports dual-channel DDR4 2133MHz
Rear Panel I/O
Ports
• Rear Panel
- One RS-232 (DB-9)
- Line-out and Mic-in ports
- One HDMI port
- Four USB 3.0 Type A ports
- Two USB 2.0 Type A ports
- Two RJ45 LAN ports
- One 9~36V terminal block
- Five wireless module antenna holes
Power
• Power input voltage: 9~36V DC-in (terminal block with ignition control)
Cooling System
• Fanless with heatsink
Environment
• Realtek ALC888 5.1-channel
• Audio ports:
Mic-in and Line-out
• Operating Temperature:
-20 to 60°C (wide temperature SSD or mSATA mini)
• Storage Temperature:
-20 to 85°C
• Relative Humidity:
5 to 95% RH (non-condensing)
Construction
• Aluminum + Sheet Metal
Mounting
Storage
• Full-size Mini PCIe (PCIe/USB)
• Half-size Mini PCIe (PCIe/USB/SATA)
• Wall/VESA/DIN-rail Mount
Dimensions
• 184mm x 82mm x 118.4mm (W x H x D)
Ethernet
1 x Intel® I210IT PCIe (10/100/1000Mbps)
1 x Intel® I219LM with iAMT11.0 PCIe (10/100/1000Mbps) (only Core i7/i5
supports iAMT)
Weight
• 1.6 Kg
OS Support
Expansion
One full-size Mini PCIe (PCIe/USB)
One half-size Mini PCIe (PCIe/USB/SATA)
• Windows 10 (64-bit)
• Windows 10 IoT Enterprise (64-bit)
• Ubuntu 16.04 LTS
Other Features
System Reset, Programmable via Software from 1 to 255 Seconds
Standards and
Certifications
Shock:
MIL-STD 810G 516.6
Operating: 10G, 11ms
Non-Operating: 40G, 11ms
• Supports 4GB/8GB memory onboard
Graphics
Intel® HD Graphics GT Series
OpenGL 5.0, DirectX 12, OpenCL 2.1
• Supports these codecs:
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265,
VP8, VP9
HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9
• Output displays:
VGA: resolution up to 1920x1200 @ 60Hz
HDMI: resolution up to 4096x2160 @ 24Hz
• Dual display: VGA + HDMI
Audio
Front Panel I/O
Ports
• Front Panel
- Power button with LED
- Reset button
- Status LED
- HDD LED
- VGA Port
- Five (two support RS232/422/485; two support only RS232; one
supports RS232 or 8-bit DIO or CAN bus)
Vibration:
MIL-STD 810G 514.6C-3
Certifications:
CE, FCC Class A, RoHS
7
Chapter 1 Introduction
www.dfi.com
Getting to Know the VC70B-KU
Front View
Status LED
(blue)
Power Button with LED
(green)
VGA
COM 2
COM 1
COM 3
Line-out
COM 4/ 8-bit DIO
USB 3.0
HDMI
USB 3.0
Mic-in
LAN 2 LAN 1
HDD LED
Reset
DC-in
USB 2.0
COM 5
COM 6
Antenna holes
Power button with LED (Green)
Press to power on or power off the system.
COM Port
Connects serial devices; COM 3 supports only RS232.
Status LED (Blue)
Indicates system status.
Microphone/Line-out Ports
Connect audio devices such as microphones and speakers.
Status LED
Suspend Mode
S0
Sleep
S4, S5
LED Behavior
ON
Blinks
Off
HDMI*
Connects the HDMI connector of an LCD monitor.
USB 3.0/2.0 Ports
Connect USB 3.0 and 2.0 devices as well as devices based on previous USB versions.
Reset Button
Press to reset the system.
Gigabit LAN Ports
Connect the system to a local area network.
COM Ports
DC-in
DC 9~36V power input via a DC-in jack.
Connect serial devices. COM 1 and COM 2 support RS232/422/485; COM 4 can be selected
among RS232, 8-bit digital IO and CAN bus port via jumper settings; COM 5 and COM 6
support only RS232.
Antenna Holes
Connect a wireless module’s antennas.
VGA
Connects the VGA connector of a monitor.
HDD LED (Blue)
Indicates the status of the hard drive.
Notes:
The HDMI is a DP++/HDMI combo port but can only transmit HDMI signals (unless wired as
a DP++ port). Please plug in an HDMI cable with the right orientation and alignment to avoid
damage to the connector. You should feel resistance (due to a pin on the right) if the cable is not
inserted correctly. Please see a video at https://youtu.be/SUj07rfN5l8 for detailed instructions.
HDD LED
HDD State
Disk access
activity
HDD present or HDD not present
LED Behavior
Blink
Off
Aligning side
(left)
Angled-corner
pin
Angled-corner
(up)
Align this edge with the
left side of the connector
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
Chassis Dimensions
Motherboard Dimensions
160.00
142.82
129.90
106.90
75.40
71.02
35.52
14.90
6.10
5.00
82.00
184.00
115.00
118.40
103.20
98.20
Left View
Right View
18.00
8.00
0.00
165.00
147.40
123.21
106.50
87.09
73.05
58.99
40.27
23.77
7.29
0.00
9
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
SATA hard drive
AC power adapter and other means of power supply
CD-ROM drive (for installing software/drivers)
Installing Devices
The following devices can be installed in the system.
•
•
•
SATA drives
Mini PCIe card
mSATA card
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1.
2.
Power on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing a Operating System
Depending on the method you choose to install your system, you may use a USB flash drive
or install a CD-ROM drive in order to run the Operating System CD.
Make sure a SATA drive or an mSATA card is already installed.
1.
Refer to the following chapters for information on connecting a CD-ROM drive and installing a SATA drive.
2.
Refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
10
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing the Devices
Removing the Chassis Cover
Installing a SATA Drive
Please observe the following guidelines and follow the procedure to open the system.
The system can accommodate one SATA drive installation.
1. Make sure the system and all other peripheral devices connected to it have been powered off.
1.
Use the SATA HDD brackets included in the product package to install a SATA HDD in the system.
2. Disconnect all power cords and cables.
SATA data and power cable
3. The 2 mounting screws on the bottom side of the system are used to secure the cover to the
chassis. Remove these screws and put them in a safe place for later use.
2.5" SATA drive
Mounting screw
Chassis screw
Mounting screws
4. After removing the chassis screws, lift the bottom chassis cover to open the system. The HDD
mounting posts are accessible after removing the bottom cover. To access the main board,
please remove the power board first.
Note:
Please connect the SATA cable first before installing the HDD on the HDD bracket. The HDD
bracket might block the access to the SATA connectors on the HDD.
Power board
mounting screw
2. Place the SATA drive bay with the installed HDD back to the system and connect the SATA
cable to the SATA connectors on the system board.
SATA power connector
SATA mounting place
SATA data connector
Power board
SATA cable
Mounting screw
Mounting screw
11
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a Mini PCIe Card
1.
The system board is equipped with 2 Mini PCIe slots: one full-size and one half-size slot. Here we
will demonstrate the installation of a full-size Mini PCIe card.
Grasp the Mini PCIe card by its edges and align the notch of the PCIe card with the key in
the connector on the system board.
2.
Push the Mini PCIe card down and use the provided mounting screw to secure the card on
the system board.
The Mini PCIe sockets are located on the main board; to access the main board, detach the
power board on top of it. Remove the screws that affix the rear bezel as shown in the following
picture to access the power board and uninstall it from the system.
Mounting screw
Use a wrench or a screwdriver
with a socket end to remove
the fasteners used on DB-9
connectors.
Screw
Notes:
1.
The system also has a half-size Mini PCIe slot that can accommodate either a Mini PCIe or
an mSATA card. Refer to jumper settings for signal selection for this slot.
Remove these screws to
detach the power board
from the main board
2.
The power board connects to the mainboard with a 4-pin power cable, please reconnect this
cable if it is removed during installation.
Screw
12
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a CANbus card in the Mini PCIe slot
To install a CANbus card, connect the cable between the card the pin headers (JP1 and JP2),
then you can use COM 4 as a CANbus port. For pin assignments of this port, refer to Chapter 5 ̶
Ports and Connectors. To switch signals for COM 4, refer to Chapter 4 ̶ Jumper Settings.
JP1/JP2
Mounting screw
CANbus card
13
Chapter 3 Installing the Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
Auto Power-on Select
Clear CMOS Data
COM 3
COM 3
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
LAN 2
Realtek ALC888
MIC-in
LAN 1
DC-in
USB 2
USB 1
USB 3.0
LINE-out
1
Realtek ALC888
COM 6
2
COM 6
2
COM 5
MIC-in
DC-in
COM 5
2
1
1
2
1
1
LAN 1
USB 2
USB 1
USB 3.0
1
SATA 3.0
1
SATA 3.0
USB 4
USB 3
USB 3.0
HDMI
SATA_0
SATA_0
(RS232)
SATA Power
(RS232)
Intel
WGI210AT
Intel
WGI210AT
Mini PCIe
Mini PCIe
USB 2.0 7/8
10
USB 2.0 7/8
1
10
JP1
1
12
JP1
12
1
JP3 1
JP4 1
SPI Flash
BIOS
Mini PCIe /mSATA
JP2
Battery
DDR4
COM4/DIO Pin Select
COM4/DIO Pin Select
Mini PCIe PCIe/
SATA Select
Clear CMOS
12
1
JP3 1
JP4 1
6
(RS232/DIO/CAN bus)
2 1
Battery
1
COM 4
DDR4
DDR4
DDR4
JP2
VGA
6
Reset Power
3
COM 2
(RS232/422/485)
1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
COM 4
(RS232/DIO/CAN bus)
COM 1(RS232/422/485)
COM4/DIO Pin Select
COM4/DIO Pin Select
Mini PCIe PCIe/
SATA Select
Clear CMOS
(JP1)
(JP2)
(JP3)
JP4
1 2 3
1-2 On:
Normal
2-3 On:
Clear CMOS
(JP1)
(JP2)
(JP3)
VGA
DDR4
DDR4
DDR4
LED 1
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
JP7
(JP4)
3
1-2 On:
Normal
You can reconfigure the system with the default values stored in the ROM BIOS if you encounter the following situations:
2 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
1
(JP4)
1 2 3
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
12
1
1
3
2-3 On:
Auto-Power on
JP7 is used to select the method of powering on the system. If you want the system to power
on whenever ignition signal comes in, set JP7 pins 2 and 3 to On. If you want to use the
power button, set pins 1 and 2 to On.
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
When using the JP7 “Power On” feature to power the system back on after a power failure
occurs, the system may not power on if the power lost is resumed within 5 seconds (power
flicker).
To load the default values stored in the ROM BIOS, please follow these steps below.
1. Power off the system and unplug the power cord.
2. Set jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper back to its default setting, pins 1 and 2 On.
3. Now plug the power cord and power on the system.
14
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Mini PCIe/SATA Signal Select
COM 3
COM4/DIO Select
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
Realtek ALC888
MIC-in
COM 3
LAN 1
COM 6
2
LINE-out
1
SATA_0
COM 5
Realtek ALC888
LAN 1
DC-in
USB 2
USB 1
USB 3.0
MIC-in
1
COM 6
SATA 3.0
2
1
1
LAN 2
USB 4
USB 3
USB 3.0
HDMI
1
SATA 3.0
(RS232)
SATA Power
DC-in
USB 2
USB 1
USB 3.0
2
COM 5
2
1
1
Intel
WGI210AT
Intel
WGI210AT
Mini PCIe
Mini PCIe
USB 2.0 7/8
USB 2.0 7/8
10
10
1
1
JP1
JP1
12
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
DDR4
DDR4
1
2 1
JP2
12
1
Battery
1
6
COM 4
VGA
(RS232/DIO/CAN bus)
COM4/DIO Pin Select
COM4/DIO Pin Select
Mini PCIe PCIe/
SATA Select
Clear CMOS
DDR4
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
(RS232/422/485)
SPI Flash
BIOS
1
Reset Power
3
COM 2
JP3 1
JP4 1
6
COM 4
COM 1(RS232/422/485)
COM4/DIO Pin Select
COM4/DIO Pin Select
Mini PCIe PCIe/
SATA Select
Clear CMOS
(JP4)
JP3
1-2 On: mSATA
(default)
JP1
JP2
1 2 3
DDR4
JP3 is used to select the signal for the half-size Mini PCIe slot: PCIe or mSATA (default).
2 1
LED 1
Auto PWR ON
(JP7)
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
(JP1)
(JP2)
(JP3)
(JP4)
1
3
1
3
10
12
10
12
1-2, 4-5,
7-8, 10-11 On: COM4
2-3 On: PCIe
DDR4
DDR4
Front
Panel
(JP11)
VGA
(RS232/DIO/CAN bus)
(JP1)
(JP2)
(JP3)
1 2 3
DDR4
Mini PCIe /mSATA
12
Mini PCIe /mSATA
1
JP2
2-3, 5-6,
8-9, 11-12 On:
DIO
The system board uses JP1 and JP2 to select between RS232 serial communication or 8-bit
digital I/O for the DB-9 connector (COM 4) on the front panel.
Important:
You cannot use COM 4 and DIO at the same time. Please set JP1 and JP2 together.
15
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
Front Panel I/O Ports
Rear Panel I/O Ports
Status LED
(blue)
COM 1
HDMI
COM 3
COM 2
VGA
USB 3.0
LAN 2 LAN 1
HDD LED
(blue)
Power button
(Green LED)
Line-out
Mic-in
Rear View
Front View
DC-in
Grounding
Antenna
hole
Reset
COM 5
COM 6 COM 4/ 8-bit DIO
CANbus*
USB 2.0
The front panel I/O consists of the following ports:
The rear panel I/O consists of the following ports:
•
•
•
•
•
• 3-pole DC-in connector
Power button with LED (green)
Reset button
Status and HDD LEDs (blue)
VGA port
Five RS232 serial COM ports:
- COM 1 & COM 2 are RS232/422/485 ports
- COM 4 can be an RS232, an 8-bit DIO or a CANbus port
- COM 5 & COM 6 are RS232 ports
• Line-out and mic-in ports
• Two Ethernet ports
• Four USB 3.0 ports
• Two USB 2.0 ports
• One HDMI port
• One serial COM port:
- COM 3 is an RS232 port
16
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
Display Interfaces
BIOS Setting
The display ports consist of the following:
Configure the display devices in the Advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
•
•
Driver Installation
1 HDMI
1 VGA
Install the graphics driver. Refer to Chapter 8 for more information.
COM 3
HDMI
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
Realtek ALC888
MIC-in
LAN 1
DC-in
USB 2
USB 1
USB 3.0
1
COM 6
SATA 3.0
2
COM 5
2
1
1
Intel
WGI210AT
Mini PCIe
USB 2.0 7/8
10
1
JP1
12
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
JP2
1
VGA
6
COM 4
(RS232/DIO/CAN bus)
VGA
DDR4
DDR4
DDR4
2 1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
HDMI Port
The HDMI port, which carries both digital audio and video signals, is used to connect the
HDMI port of an LCD monitor or a digital TV.
17
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
USB Ports
BIOS Setting
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
USB 3.0
COM 3
USB 1
USB 4
USB 2 USB 7
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
Realtek ALC888
MIC-in
Driver Installation
USB 2.0
USB 3
You may need to install the proper drivers in your operating system to use USB devices. Refer
to Chapter 8 for more information.
USB 8
LAN 1
DC-in
USB 2
USB 1
USB 3.0
1
COM 6
SATA 3.0
2
COM 5
2
1
1
Intel
WGI210AT
Mini PCIe
USB 2.0 7/8
10
1
JP1
12
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
JP2
1
6
COM 4
(RS232/DIO/CAN bus)
VGA
DDR4
DDR4
DDR4
2 1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
The system board is equipped with four onboard USB 3.0 ports (USB 1-4). USB devices allow
data exchange between your computer and a wide range of simultaneously accessible external
Plug and Play peripherals.
18
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
COM (Serial) Ports
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
Realtek ALC888
MIC-in
1 2345
6789
6789
LAN 1
DC-in
USB 2
USB 1
USB 3.0
COM 6
SATA 3.0
2
6789
RS422
Full Duplex
RS485
COM 5
2
1
1
1 2345
RS232
1
DATA+
DATAN.C.
N.C.
GND
1 2345
N.C.
N.C.
N.C.
N.C.
COM 3
COM 5, COM 6: RS232
DSR
RTS
CTS
RI
COM 3: RS232
N.C.
N.C.
N.C.
N.C.
DCD
RXD
TXD
DTR
GND
RX+
RXTX+
TXGND
COM 1 (RS232/422/485) / COM 2 (RS232/422/485) / COM 3 (RS232 only)
COM 4 (Serial) Port
Intel
WGI210AT
Mini PCIe
This DB-9 serial port can be configured as an RS232 serial port or as an 8-bit DIO connector
via jumper settings. Refer to “COM4/DIO Select” in Chapter 4 for its respective configuration.
USB 2.0 7/8
8-bit Digital IO/CANbus
10
1
JP1
The 8-bit Digital I/O connector provides monitoring and control functions to the connected
external devices. We have built support software called EAPI that enables the functionality of
hardware components. Please contact our tech support or sales representatives for the support
software package. In addition, you can configure this port to be CANbus compatible; please
refer to “Installing a CANbus card in the Mini PCIe slot” in Chapter 3.
12
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
JP2
1
6
COM 4
(RS232/DIO/CAN bus)
COM 4 (or 8-bit DIO): RS232
VGA
DDR4
DDR4
DDR4
2 1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
COM 4 Function
Reset Power
3
COM 2
Pins
COM 1(RS232/422/485)
(RS232/422/485)
COM 2: RS232/RS422/RS485
COM 1: RS232/RS422/RS485
COM 1 and COM 2 can be selected among RS232, RS422 and RS485 whereas COM 3 and COM
4 are fixed at RS232. Use the BIOS configuration utility to select the communication mode for
COM 1 and COM 2.
BIOS Setting
Configure the serial ports including the communication mode in the “Advanced” menu (Super
I/O submenu) of the BIOS. Refer to Chapter 7 for more information.
RS232
DIO
CANbus
1
DCD
DIO0
CAN1-L
2
RXD
DIO1
CAN1-H
3
TXD
DIO2
CAN2-L
4
DTR
DIO3
CAN2-H
5
GND
GND
GND
6
DSR
DIO4
J1708-L
7
RTS
DIO5
J1708-H
8
CTS
DIO6
N/C
9
RI
DIO7
N/C
19
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
RJ45 LAN Ports
Audio
Mic-in
Line-out
Speed LED
ACT/Link
COM 3
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
(RS232)
LAN 2
SATA Power
COM 3
Realtek ALC888
MIC-in
LAN 1
DC-in
USB 2
USB 1
USB 3.0
LINE-out
1
SATA_0
Realtek ALC888
SATA 3.0
2
COM 6
2
DC-in
COM 5
2
1
1
COM 5
2
1
1
MIC-in
LAN 1
USB 2
USB 1
USB 3.0
1
SATA 3.0
1
COM 6
USB 4
USB 3
USB 3.0
HDMI
Intel
WGI210AT
Intel
WGI210AT
Mini PCIe
Mini PCIe
USB 2.0 7/8
10
USB 2.0 7/8
1
10
JP1
12
1
JP2
12
JP2
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
1
JP3 1
JP4 1
6
(RS232/DIO/CAN bus)
12
2 1
Battery
1
COM 4
DDR4
DDR4
DDR4
VGA
6
Reset Power
3
COM 2
(RS232/422/485)
1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
JP1
COM 4
(RS232/DIO/CAN bus)
VGA
DDR4
DDR4
DDR4
2 1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
COM 1(RS232/422/485)
LAN Ports
Audio Ports
•
LAN 1 is built on the Intel® I219LM PCI Express Gigabit Ethernet controller with iAMT11.0
PCIe (10/100/1000Mbps) (only Core i7/i5 supports iAMT)
The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
•
LAN 2 is built on the Intel® I210IT PCI Express Gigabit Ethernet controller
•
Line-out Jack
This jack is used to connect a headphone or external speakers.
•
Mic-in Jack
This jack is used to connect an external microphone.
The LAN ports allow the system board to connect to a local area network with a network hub
and the their LED indication is as follows:
Activity/Link LED
LED Behavior
Off
Blinking
On
Description
No link
Data Activity
Link
Speed LED
LED Behavior
Off
Green
Orange
Description
10Mbps connection
100Mbps connection
1Gbps connection
Driver Installation
Install the audio driver. Refer to the Chapter 8 for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 8 for more information.
20
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
I/O Connectors
Expansion Slots
Serial ATA Connector & Serial ATA Power Connector
1
COM 3
+12V
Ground
Ground
+5V
4
(RS232)
LAN 2
SATA Power
LINE-out
1
SATA_0
Realtek ALC888
COM 6
2
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
Realtek ALC888
DC-in
USB 2
USB 1
USB 3.0
1
COM 6
SATA 3.0
2
USB 2.0 7/8
COM 5
10
2
1
1
7
SATA 3.0 6Gb/s
MIC-in
Intel
WGI210AT
LAN 1
Mini PCIe
GND
TXP
TXN
GND
RXN
RXP
GND
DC-in
COM 5
2
1
1
COM 3
MIC-in
LAN 1
USB 2
USB 1
USB 3.0
1
SATA 3.0
1
USB 4
USB 3
USB 3.0
HDMI
1
Intel
WGI210AT
JP1
12
Mini PCIe
12
1
USB 2.0 7/8
Battery
10
JP3 1
JP4 1
1
JP1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
JP2
1
12
JP2
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
2 1
6
(RS232/DIO/CAN bus)
6
(RS232/DIO/CAN bus)
DDR4
DDR4
COM 4
1
COM 4
DDR4
VGA
(RS232/422/485)
1 Serial ATA 3.0 port with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
COM 1(RS232/422/485)
Half-size Mini PCIe with SATA or
PCIe signal
Features
•
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
Reset Power
3
COM 2
2 1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
VGA
DDR4
DDR4
DDR4
Full-size Mini PCIe
with PCIe signal
Mini PCI Express Slots
The Serial ATA connector is used to connect the Serial ATA device. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
The Mini PCI Express slots on the system board are used to install one half-size and full-size
Mini PCIe card. The half-size Mini PCIe slot can be inserted with either an mSATA card or a
Mini PCIe card; please refer to “Mini PCIe/SATA Signal Select” in Chapter 4 for more information on jumper settings for signal selection and Chapter 7 for the designated SATA port of this
slot.
The SATA power connector supplies power to the SATA drive. Connect one end of the provided
power cable to the SATA power connector and the other end to your storage device.
BIOS Setting
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
21
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
Front Panel Connector
HDD LED (HDD_LED)
This LED will be lit when the hard drive is being accessed.
COM 3
(RS232)
LAN 2
SATA Power
USB 4
USB 3
USB 3.0
HDMI
LINE-out
1
SATA_0
Realtek ALC888
MIC-in
Reset Button (RESET_BTN)
LAN 1
This switch allows you to reboot without having to power off the system.
DC-in
USB 2
USB 1
USB 3.0
Power Button (PWR_BTN)
1
COM 6
SATA 3.0
2
COM 5
2
1
1
This switch is used to power on or off the system.
Intel
WGI210AT
Mini PCIe
Status LED (SUS_LED)
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
USB 2.0 7/8
10
1
Power/Standby LED (PWR_LED)
JP1
12
JP2
12
1
Battery
JP3 1
JP4 1
SPI Flash
BIOS
DDR4
Mini PCIe /mSATA
1
1
6
COM 4
(RS232/DIO/CAN bus)
2 1
LED 1
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
1 2
PWR_BTN
RESET_BTN
5 6
Pin Pin Assignment
HDD_LED
RESET_BTN
6
HDD Power
3
Ground
3
Ground
5
RST Signal
This LED will blink when the system is in the standby mode. It indicates that there is power
on the system board.
Auto PWR ON
(JP7)
Front
Panel
(JP11)
VGA
DDR4
DDR4
DDR4
PWR_LED
SUS_LED
HDD_LED
Pin Pin Assignment
PWR_BTN
PWR_LED
SUS_LED
1
Power Button
3
Ground
2
Power LED
3
Ground
3
Ground
4
SUS LED
22
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
Standby Power LED
COM 3
Battery
(RS232)
LAN 2
SATA Power
LINE-out
1
LAN 1
COM 3
USB 4
USB 3
USB 3.0
HDMI
Realtek ALC888
MIC-in
(RS232)
DC-in
USB 2
USB 1
USB 3.0
LINE-out
COM 6
2
COM 5
SATA_0
2
1
1
COM 6
2
USB 2.0 7/8
Battery
1
Intel
WGI210AT
Mini PCIe
Mini PCIe
1
DC-in
COM 5
2
1
1
Battery
Ground
MIC-in
LAN 1
USB 2
USB 1
USB 3.0
1
SATA 3.0
Intel
WGI210AT
10
USB 2.0 7/8
10
1
JP1
JP1
12
12
1
Battery
SPI Flash
BIOS
6
(RS232/DIO/CAN bus)
DDR4
DDR4
1
2 1
JP2
12
Standby
Power LED
1
COM 4
DDR4
Battery
JP3 1
JP4 1
SPI Flash
BIOS
1
6
Reset Power
3
COM 4
(RS232/DIO/CAN bus)
VGA
DDR4
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
1
Mini PCIe /mSATA
12
DDR4
Mini PCIe /mSATA
1
JP2
JP3 1
JP4 1
Realtek ALC888
1
SATA 3.0
USB 4
USB 3
USB 3.0
HDMI
1
SATA_0
LAN 2
SATA Power
COM 2
(RS232/422/485)
DDR4
2 1
LED 1
Auto PWR ON
(JP7)
Front
Panel
(JP11)
VGA
DDR4
DDR4
Reset Power
3
COM 2
(RS232/422/485)
COM 1(RS232/422/485)
COM 1(RS232/422/485)
Battery
Connect to the battery connector
This LED will blink when the system is in the standby mode. It indicates that there is power
on the system board. Power off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
23
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 5
Power Connector (power board)
H1
System-on/off Delay Switch
The DIP switch (SW1) on the power board (X103- DC36 ) can be used to turn on or off the system at a specific on/off delay time via car ignition. Note that this table shows that same information as the one in Chapter 4 - Jumper Settings.
1
Power
Switch
(J2)
ON
12345678
System-on/system-off delay
(SW1)
SW1-2: System-on delay enable/disable
Enable (delay time setting adjustable by SW1-4 and 1-5 as shown in
the table below)
Off
Disable (System-on delay = 3 sec)
1
1
On (Default)
SW1-4 and 1-5: System-on delay time setting
1
2
4
On
Off
On
Off
3
H4
IGN
H3
DC-IN
S1
DC-in
VCC
GND
System startup process with in-vehicle power control
Ignition On
Counts down
System-on
delay time
Ignition Off
System shuts down
& finishes shutdown
process at the
specified delay time
On (Default)
Enable (delay time setting adjustable by SW1-6, 1-7 and 1-8 as
shown in the table below)
Off
Disable (System-off delay = 0 sec)
SW1-6, 1-7 and 1-8: System-off delay time setting
6
System boots
System
On
System shutdown process with in-vehicle power control
System
On
Time
10 sec (default)
30 sec
1 min
5 min
SW1-3: System-off delay enable/disable
DC-out
(to the system board)
System
Off
5
On
On
Off
Off
System
Off
7
8
Time
On
On
On
Off
On
On
1 min
On
Off
On
3 min
Off
Off
On
5 min
On
On
Off
10 min
Off
On
Off
15 min
On
Off
Off
30 min
Off
Off
Off
1
30 sec (default)
hr
Note:
The OS will start the shut-down procedure after the car ignition switches off and
will complete the shutdown procedure within the specified system-off delay time.
Please make sure that system-off delay time is sufficient to allow the OS to shut
down completely.
The 3-pole power connector connects to a car battery for power supply. Note that the system
accepts a wide power range of 9 to 36V with in-vehicle power management that includes ignition on/off and system on/off delay time control; please refer to the table on the right for
more information.
24
Installation
Chapter 2
5 Hardware
Ports and Connectors
www.dfi.com
Chapter 6
Chapter 6 - Mounting Options
2.
Use the provided mounting screws to attach the wall mount brackets to both sides on the
bottom of the system.
Wall Mount
The wall mount kit includes the following:
•
•
Mounting screw
2 Wall mount brackets
Bracket screws
Wall mount
bracket
The following diagrams show the location and dimension of the wall moutning holes.
Remove the rubber feet from the bottom cover chassis. Or if the rubber feet are not attached
to the chassis, use these screw holes to mount wall brackets.
108.00
80.00
46.00
25.00
1.
Mounting screw holes
19
16.00
5.00
108.00
80.00
46.00
25.00
Ø8.50
Ø3.50
192.80
25
Chapter 6 Mounting Options
Chapter 6
VESA Mount
2.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
The
•
•
•
Attach the VESA mount bracket A to the back of your display using four screws as shown in
the picture below.
vesa mount kit includes the following:
1 VESA mount bracket A
2 VESA mount bracket B
Bracket screws
Mounting Screw
VESA mount bracket A
VESA bracket A
3.
Align VESA bracket A with VESA bracket B, and then use the provided mounting screws to
attach both brackets to secure the system in place.
VESA bracket B
Mounting Screw
The system
1.
Attach the VESA mount bracket B to the left and right sides on the bottom of the system.
The following diagrams show the location and dimension of the vesa moutning holes.
209.00
Mounting screw
209.00
Ø5.00
26
75.00
75.00
100.00
100.00
121.60
121.60
VESA bracket B
Chapter 6 Mounting Options
Ø5.00
75.00
75.00
100.00
100.00
Chapter 6
DIN Rail Mount
2.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
The
•
•
•
DIN Rail mount kit includes the following:
1 DIN-rail mount clip
1 bracket
Bracket screws
1.
Locate the mounting screws for mounting the din-rail bracket on the chassis cover. Remove these screws and put them in a safe place for later use.
3. The 3 mounting holes on the bracket are used to affix the DIN-rail mount clip to the
bracket.
Mounting Screw
Mounting Screw
27
Chapter 6 Mounting Options
Align the mounting holes on the system and the mounting holes on the bracket, and then
use the screws removed in step 1 to secure the bracket in place.
Chapter 7
Chapter 7 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup Defaults
<F10>
Save and Exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
Entering the BIOS Setup Utility
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
28
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1980 to 2099.
29
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
CPU Configuration
Video Configuration
This section configures the CPU.
This section configures the video settings. Note that the configuration options may vary depending on the “Boot type” selected in the “Boot” menu.
Primary Display
Intel® SpeedStep™
Note that this configuration is only shown if the “Boot Type” is set to “Dual” or “UEFI”.
Select the primary display for the system from the following options:
Enable or disable the Enhanced Intel SpeedStep® Technology, which helps optimize the
balance between system’s power consumption and performance. After it is enabled in
the BIOS, you can enable the EIST feature using the operating system’s power management feature.
Auto mode: Automatic selection
PCI: PCI graphics devices
IGFX: IGFX (internal graphics) devices
PEG: PCIe graphics device
CPU C States
Enable or disable CPU Power Management. It allows the CPU to go to C states when it’s
not 100% utilized.
Internal Graphics Device
Enable, disable or automatically detect the internal graphics device.
Hyper-Threading
Enable Intel Hyper-Threading Technology (HT) on the processor to improve performance of operating systems and software that are optimized for hyper-threading
technology. Please check the software specifications to determine if enabling HT can be
advantageous to the overall system performance.
®
Boot Display
Note that this configuration is only shown when the “Boot Type” is set to “Legacy Boot
Type” or “Dual”. Select the combination of the display at boot: Auto, HDMI+VGA or
VGA+HDMI.
30
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Audio Configuration
SATA Configuration
This section configures the audio settings.
This section configures the SATA controllers and hard disks.
HD Audio
SATA Controller(s)
Control the detection of the high-definition audio devices.
Enable or disable Serial ATA controllers.
Disabled
SATA Speed
High-definition audio devices will be unconditionally disabled.
Select Serial ATA device speed: Gen1 (1.5 Gbit/s), Gen2 (3 Gbit/s), Gen 3 (6 Gbit/s) or
auto.
Enabled
High-definition audio devices will be unconditionally enabled.
Auto
High-definition audio devices will be enabled if present and disabled otherwise.
31
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
USB Configuration
This section configures the parameters of the USB devices.
SATA Mode
Legacy USB Support
The mode option shows how the SATA controller(s) operates.
Disabled
Disable USB keyboard/mouse/storage support.
AHCI Mode
Enabled
Enable USB keyboard/mouse/storage support under UEFI and DOS environment.
This allows the Serial ATA devices to operate in the AHCI (Advanced Host Controller
Interface) mode.
UEFI Only
Enable USB keyboard/mouse/storage support only under the UEFI environment.
Serial ATA Port 0 and 1 and Hot Plug
XHCI Hand-off
Enable or disable each serial ATA port and its hot plug function.
Enable this function for operating systems that do not support xHCI Hand-off. The XHCI
ownership change will be claimed by the XHCI driver.
SATA Port 0: Controls the SATA signal of the SATA port on the system board.
SATA Port 1: Controls the SATA signal of the half-size mini PCIe slot.
32
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PCI Express Configuration
This section configures the settings of PCI Express root ports.
Intel I210AT/I219LM
PCI Express Root Port
Controls the PCIe signal of the Intel I210AT/I219LM controllers.
Enable or disable each PCI Express root port.
Mini PCIe Slot-1 (Full)
PCIe Speed
Controls the PCIe signal of the full-size Mini PCIe slot.
Select the speed of the PCI Express Root Port: Auto, Gen1 (2.5 GT/s), Gen2 (5 GT/s)
or Gen3 (8 GT/s).
Mini PCIe Slot-2 (half)
Hot Plug
Controls the PCIe signal of the half-size Mini PCIe slot.
Enable or disable the hot plug function of each serial ATA port.
33
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ME Configuration
Active Management Technology Support
This section configures flashing of the Intel® Management Engine.
The section allows you to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Refer to Chapter 9 - Intel AMT Settings for more information.
Me Fw Image Re-Flash
Intel AMT Support
Enable or disable flashing of the Intel® Management Engine (ME) region.
Enable or disable Intel® Active Management Technology BIOS extension.
Un-Configure ME
Clears all ME related configurations without requiring a password on the next boot.
34
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Debug Configuration
UEFI Device Manager
This section configures the debug function.
This Device Manager menu is used to configure UEFI network settings when the “Network
Stack” is enabled in the “Dual” or “UEFI” boot mode. Refer to the “Boot” section in this
chapter. When this function is selected, the screen will warn you that you are going to exit the
BIOS setup utility.
Dynamic EFI Debug
Enable or disable output of the debugging messages through a serial port.
35
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Network Device List
NIC Configuration Menu
The “Device Manager” screen is displayed. And if the “Network Stack” or the “PXE Boot to
LAN” option is enabled from the “Boot” menu, the “Network Device List” should be shown
in the “Device list”. Select “Network Device List” to view all of the detected network devices. For each network device, you can select to view and configure its settings. In addition,
you can select either the IPv4 or IPv6 network settings for UEFI network configuration.
This screen shows hardware information for the Ethernet controllers and configures their operation.
36
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Blink LEDs
IPv6 Network Configuration
Enter the duration (seconds) for the Ethernet’s speed LED to blink to indicate its presence.
If you select to use IPv6 network settings, enter the Interface ID (64 bit).
Policy: Select either automatic or manual. And select "Advanced Configuration" to configure IPv6
network address manually if the manual option is selected.
New IPv6 address: Enter the IP address in the IPv6 format:
x : x : x : x : x : x : x : x (x can be any hexadecimal value between 0 and FFFF). Place a space
to separate each IP address to enter more than one address.
New Gateway addresses: Enter gateway addresses in the IPv6 format.
New DNS addresses: Enter DNS (Domain Name System) server IP addresses in the IPv6 format.
NIC Configuration
This screen configures the Ethernet controller. Select the link speed from the following options:
Auto Negotiated, 10Mbps Half, 10Mbps Full, 100Mbps Half, and 100Mbps Full.
IPv4 Network Configuration
This screen configures the IP addressing method (DHCP or static IP). For static IP addressing,
configure the following:
Local IP address and subnet mask: Enter the IP address in the IPv4 format:
x . x . x . x (x must be a decimal value between 0 and 255).
Local Gateway: Enter the gateway address in the IPv4 format.
Local DNS (Domain Name System) Servers: Enter DNS (Domain Name System) server IP
addresses in the IPv4 format.
37
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
SIO NUVOTON6106D
This section configures the system super I/O chip parameters.
CPU Smart Fan Control
Enable or disable the system or CPU smart fan.
Boundary 1 to Boundary 4
Set the boundary temperatures that determine the operation of the fan with different
fan speeds accordingly. For example, when the system or the CPU temperature reaches
boundary temperature 1, the system or CPU fan should be turned on and operate at the
designated speed. The range of the temperature is from 0 to 127oC.
Fan Speed Count 1 to Fan Speed Count 4
Set the fan speed. The range is from 1 (lowest speed)-100% (full speed).
38
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PC Health Status
This section displays PC health status.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable
WDT. Input any value between 1 and 255.
Case Open
Enable or disable the case open function.
39
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
COM1 to COM6
Enable or disable the serial redirection function for each of the serial ports on the system. And configure the serial communication parameters to be used between the system
and a remote station.
Console Redirection
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
UseGlobalSetting
Choose to use the pre-configured global settings from the previous menu or configure a
different setting for each serial port.
Console Serial Redirect
Enable or disable the console redirection function. (The default is disabled.) If you
select to enable it, please configure the following parameters for serial communication between the system and a remote station:
Terminal type: VT_100, VT_100+, VT_UTF8, or PC_ANSI.
Baud rate: 115200, 57600, 38400, 19200, 9600, 4800, 2400 or 1200.
Data bits: 8 bits or 7 bits.
Parity: None, Even or Odd.
Stop bits: 1 bit or 2 bits.
Flow control: None, RTS/CTS or XON/XOFF
This is the global setting for all of the designated serial ports for the console redirection function.
40
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Security
This section configures the optional Trusted Platform Module (TPM) function and the
HDD security.
TPM Availability
Set Supervisor Password
Show or hide TPM availability and its configurations.
Set the administrative password for entering the BIOS utility or upon the entering of the
power-on self-test (POST) process. The length of the password must be greater than 1
character and less than or equal to 10 characters.
TPM Operation
Enable or disable the TPM function. It displays the following options:
Power-on Password
• No Operation: No changes to the current state.
If you select to set the supervisor password, this option will be shown. Enable or disable
the system to require password at boot.
• Disable: Disable and deactivate TPM.
• Enable: Enable and activate TPM.
Clear TPM
Remove all TPM ownership contents.
41
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Boot
Quiet Boot
Enable or disable the quiet boot function to configure the screen’s display between POST
messages or the OEM logo at startup. Select “Disabled (default)” to display the POST
messages and select Enabled to display the OEM logo.
This section configures boot options.
Numlock
Select the power-on state for the Numlock key.
Boot Type
Select the boot type. The options are Dual Boot Type, Legacy Boot Type or UEFI Boot
Type.
Network Stack
This option is shown only when the boot type is set to Dual or UEFI.
Enable or disable UEFI network stack. It supports the operation of these functions or
software: Windows 8 BitLocker Network Unlock, UEFI IPv4/IPv6 PXE and legacy PXE
option ROM.
PXE Boot to LAN (Legacy Boot Type)/PXE Boot Capability (Dual Boot Type)
Enable or disable Preboot eXecution Environment (PXE) boot to LAN.
USB Boot
Enable or disable booting to USB boot devices.
42
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Exit
Boot Device Priority
This section configures legacy boot order. This menu is shown only when the boot type
is set to “Legacy” or “Dual”.
This section configures the parameters for exiting BIOS setup utility.
Boot Menu
Exit Saving Changes
Normal
Select this field and press <Enter> to exit BIOS setup and save your changes.
For this option, determine the boot order for the devices within each category. Use +
and - keys to arrange the priority of the boot devices in the list. The first device in the
list has the highest boot priority.
Load Optimal Defaults
Select this field and press <Enter> to load the optimal defaults.
Discard Changes
Advance
Select this field and press <Enter>to exit the BIOS setup without saving your changes.
For this option, determine the boot order for all bootable devices. Use + and - keys to
arrange the priority of the detected boot devices in the list. The first device in the list
has the highest boot priority.
Save Setting to file
Select this option to save BIOS configuration settings to a USB drive. The operation will
fail if there aren’t any USB devices detected on the system. The saved configuration will
have the DSF file extension and can be used for restoration.
Restore Setting from file
Select this option to restore BIOS configuration settings from a USB drive. Note that this
option will not be available if there aren’t any USB devices detected on the system.
43
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the latest BIOS file and the firmware update utility.
For instructions on how to update BIOS with the flash utility, please see https://www.dfi.com/
Knowledge/Video/31 from the Knowledge Base of the DFI website.
1. The Intel® Management Engine has already been integrated into this system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
RRead file successfully.
3. If you do not follow the methods above, the Intel® Management Engine will not be
updated and will cease to be effective.
(path= “platform.ini”)
Information
Please do not remove the AC power
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: VC70B-KU
New BIOS Model name: VC70B-KU
Current BIOS version: 65.05A
New BIOS version: 65.05A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\VC70B-KU>_
100%
100%
44
Chapter 7 BIOS Setup
www.dfi.com
Chapter 8
Chapter 8 - Supported Software
The system requires you to install drivers for some devices to operate properly. To download
the latest driver, please go to the DFI Download Center:
http://www.dfi.com/DownloadCenter
Once you are in the Download Center page, select your product or type the model name and
click "Search" to find product-related resources such as documentation and drivers.
Drivers are available for the following devices in Windows 10:
•
Intel® Chipset Device Software
•
Intel® Graphics Driver
•
Intel® LAN Driver
•
Intel® ME Driver
•
Audio Driver
•
Intel® Serial IO Driver
45
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Chipset Device Software
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
Please wait while the installation is in progress.
The Intel® Chipset Device Software is used for updating Windows® INF files so that the Intel
chipset can be recognized and configured properly in the system.
To install the utility, follow these steps:
1. Setup is ready to install the
utility. Click “Next”.
4. Please wait while the installation is in progress.
2. Read the license agreement,
and then click “Yes”.
5. Click “Restart Now” to allow
the new software installation to take effect.
46
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Graphics Driver
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
To install this driver, follow these steps:
1. Setup is now ready to
install the graphics driver.
Click “Next”.
4. Setup is now installing the
driver. Click “Next” to continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is
enabled. When this is enabled and after the system reboots, the screen will turn blank for
1 to 2 minutes (while WinSAT is running) before the Windows 7/ Windows 8.1/ Windows
10 desktop appears. The “blank screen” period is the time Windows is testing the graphics
performance.
We recommend that you skip this process by disabling this function and then click “Next”.
2. Read the license agreement, and then click “Yes”.
5. Click “Yes, I want to restart
this computer now”, and
then click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
47
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel LAN Driver
4. Click “Install” to begin the
installation.
To install this driver, follow these steps:
1. Setup is preparing to install
the driver. Click “Next” to
continue.
5. After the installation is
complete, click “Finish”.
2. Click “I accept the terms in
the license agreement” if
you accept the agreement,
and then click “Next”.
3. Select the program features
you want to install, and
then click “Next”.
48
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel ME Driver
3. Setup is currently installing
the driver. After the installation is complete, click
“Next.”
To install the Intel® Management Engine (Intel® ME) Driver, follow these steps:
1. You are about to install
the driver. Click “Next”
to continue.
4. Please wait while the product is being installed.
2. Read the license agreement, and then click “Next”.
5. After the installation is
complete, click “Finish”.
49
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Audio Driver
Serial IO Driver
To install this driver, follow these steps:
To install this driver, follow these steps:
1. Setup is now ready to install the
audio driver. Click “Next”.
1. Setup is ready to install the driver.
Click “Next” to continue.
2. Follow the steps of the on-screen
instructions; click “Next” each
time you finish a step.
2. Read the license agreement carefully.
3. Click “Yes, I want to restart my
computer now”, and then click
“Finish”.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement and then
click “Next”.
Restart the system to allow the new
software installation to take effect.
50
Chapter 8 Supported Software
www.dfi.com
Chapter 8
3. Read the file information and then
click “Next”.
5. Setup is now installing the driver.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
6. Click “Finish” to exit the setup.
51
Chapter 8 Supported Software
www.dfi.com
Chapter 96
Chapter
Chapter 9 - Intel AMT Settings
Enable Intel® AMT in the BIOS
Overview
1. Power on the system then press <Del> to enter the main menu of the BIOS setup utility.
Intel Active Management Technology (Intel AMT) combines hardware and software solutions
to provide maximum system defense and protection to networked systems.
2. In the “Advanced” menu, select “Active Management Technology Support”.
®
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and the latest security applications, Intel® AMT provides the following functions.
• Discover
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
• Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
3. In the “Active Management Technology Support” menu, select “Enabled” for “Intel AMT
Support”.
52
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
Set up Intel® AMT using the Intel® Management
Engine BIOS Extension (MEBX)
4. In the “Exit” menu, select “Exit Saving Changes” and then select “OK”.
1. After the system reboots, press <Del> to enter the BIOS menu again.
2. In the “Advanced” menu, select “MEBX Configuration” to enter the Manageability Engine
BIOS Extension (MEBx) Setup.
3. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password,
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
53
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
4. Enter a password in the space provided under “Intel(R) ME Password” and then press
“Enter”. The password must include:
•
•
•
•
•
5. You will be asked to verify the password. Enter the same new password in the space provided under “Verify Password” and then press “Enter”.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Enter] = Select Entry
[Esc]= Exit
6. Select “Intel(R) ME General Settings” and then press “Enter”.
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
54
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
7. Select “Change Intel(R) ME Password” and then press “Enter”.
8.Select “Local FW Update” and then press “Enter”. Select “Enabled” or “Disabled” or
“Password Protected” and then press “Enter”.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under “Intel(R) ME New Password” and then press “Enter”.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Disabled
Enabled
Password Protected
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
<Enabled>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9. Select Previous Menu until you return to the “Main Menu”. Select “Intel(R) AMT Configuration” and then press “Enter”.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
[Esc]= Exit
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
55
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
10. In the “Intel(R) AMT Configuration” menu, select “Manageability Feature Selection” and
then press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
12. In the “SOL/Storage Redirection/KVM” menu, select “Username and Password” and then
press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
11. In the “Intel(R) AMT Configuration” menu, select “SOL/Storage Redirection/KVM” and
then press “Enter”.
13. In the “SOL/Storage Redirection/KVM” menu, select “SOL” and then press “Enter”. Select
“Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) AMT CONFIGURATION
SOL/Storage Redirection/KVM
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
sion>
> Remote Setup And Configuration
> Power Control
< Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Anytime>
<Full Unprovi-
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
56
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
14. In the “SOL/Storage Redirection/KVM” menu, select “Storage Redirection” and then press
“Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
16. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“User Consent” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
USER CONSENT
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
User Opt-in
Opt-in Configurable from Remote IT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< KVM>
< Enabled>
Disabled
Enabled
Configure When User Consent Should be Required.
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
15. In the “SOL/IDER/KVM” menu, select “KVM Feature Selection” and then press “Enter”.
Select “Enabled” or “Disabled” and then press “Enter”.
[Esc]= Exit
17. In the “User Consent” menu, select “User Opt-in” and then press “Enter”. Select “None”
or “KVM” or “ALL” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
57
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
20. In the “Intel(R) AMT Configuration” menu, select “Network Setup” and then press “Enter”.
18. In the “User Consent” menu, select “Opt-in Configurable from Remote IT” and then press
“Enter”. Select “Enabled” or “Disable Remote Control of KVM Opt-in Policy” and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) AMT CONFIGURATION
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< ALL>
< Enabled>
Disabled
Enabled
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
21. In the “Intel(R) ME Network Setup” menu, select “Intel(R) ME Network Name Settings”
and then press “Enter”.
19. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“Password Policy” and then press “Enter”.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) ME NETWORK SETUP
INTEL (R) AMT CONFIGURATION
> Intel (R) ME Network Name Settings
> TCP/ IP Settings
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Stepup And Configuration
Anytime
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Enter] = Select Entry
[Esc]= Exit
58
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
22. In the “Intel(R) ME Network Name Settings” menu, select “Host Name” and then press
“Enter”. Enter the computer’s host name and then press “Enter”.
24. Select “Shared/Dedicated FQDN” and then press “Enter”. Select “Shared” or “Dedicated”
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) ME NETWORK NAME SETTINGS
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Host Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
Dedicated
Shared
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc]= Discard Changes
23. Select “Domain Name” and then press “Enter”. Enter the computer’s domain name and
then press “Enter”.
25. Select “Dynamic DNS Update” and then press “Enter”. Select “Enabled” or “Disabled” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) ME NETWORK NAME SETTINGS
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Domain Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
Disabled
Enabled
[Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
59
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
26. Select Previous Menu until you return to the “Intel(R) ME Network Setup” menu. Select
“TCP/IP Settings” and then press “Enter”.
28. In the “Intel(R) AMT Configuration” menu, select “Activate Network Access” and then
select “Yes/No” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
TCP/ IP SETTINGS
INTEL (R) AMT CONFIGURATION
> Wired LAN IPV4 Configuration
[↑↓] = Move Highlight
[Enter] = Select Entry
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Activates the current network settings
and opens the ME network interface
Continue: (Y/N)
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
[Esc]= Exit
27. In the “TCP/IP Settings” menu, select “Wired LAN IPV4 Configuration” and then press
“Enter”.
29. In the “Intel(R) AMT Configuration” menu, select “Unconfigure Network Access” and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
WIRED LAN IPV4 CONFIGURATION
INTEL (R) AMT CONFIGURATION
DHCP Mode
<Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
Disabled
Enabled
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<During Setup And
Configuration>
<Full Unprovision>
Full Unprovision
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
60
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
30. In the “Intel(R) AMT Configuration” menu, select “Remote Setup And Configuration” and
then press “Enter”.
32. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning Record” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) AMT CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
< Enabled>
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
<Anytime>
<Full Unprovision>
Provision Record is not present
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
31. In the “Intel(R) Remote Setup And Configuration” menu, select “Current Provisioning
Mode” and then press “Enter”.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
Provisioning Mode: PKI
[Enter] = Select Entry
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) REMOTE SETUP AND CONFIGURATION
[↑↓] = Move Highlight
[Enter] = Select Entry
33. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server IPV4/
IPV6”, enter “Provisioning server address” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Provisioning server address
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
61
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
34. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server
FQDN”, enter the FQDN of Provisioning server, and then press “Enter”.
36. In the “Intel(R) Remote Setup And Configuration” menu, select “TLS PKI” and then press
“Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) REMOTE SETUP AND CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
35. In the “Intel(R) Remote Setup And Configuration” menu, select “RCFG” and press “Enter”,
and then select “Start Configuration Y/N” and press “enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
This will activate Remote Condiguration. Continue: (Y/N)
[Enter] = Select Entry
[Esc]= Exit
37. In the “Intel(R) Remote Configuration” menu, select “Remote Configuration**” and press
“Enter”, and then select “Enabled” or “Disabled” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
[↑↓] = Move Highlight
[Enter] = Select Entry
< Enabled>
_
Disabled
Enabled
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
62
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
40. In the “Intel(R) AMT Configuration” menu, select Power Control, and then press “Enter”.
38. Select “PKI DNS Suffix”, enter the “PKI DNS Suffix”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Hash Name
VeriSign Class 3
VeriSign Class 3
Go Daddy Class 2
Comodo AAA CA
Starfield Class 2
VeriSign Class 3
VeriSign Class 3
VeriSign Class 3
GTE CyberTrust G1
Baltimore Cyber Tr
Cyber Trust Global
Verizon Global Ro
Entrust. net CA (2
Entrust Root CA
VeriSign Universa
Go Daddy Root CA
Entrust Root CA Startfield Root CA
< Enabled>
_
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[Ins]= Add New Hash
[↑↓] =Move Highlight
39. Select “Manage Hashes” and press “Enter”, and then select one of the hash names.
< Enabled>
_
[Enter] = Select Entry
Algorithm
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
[+] = Activate Hash
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) REMOTE CONFIGURATION
[↑↓] = Move Highlight
[Delete] = Delete Hash
[Enter] = View Hash
Default
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
41. In the “Intel(R) AMT Power Control” menu, select “Intel(R) AMT ON in Host Sleep States”
and then press “Enter”. Select an option and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Active
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<Anytime>
<Full Unprovision>
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
63
Chapter 9 Intel AMT Settings
www.dfi.com
Chapter 96
Chapter
44. Select Previous Menu until you return to the “Main Menu”. Select “Exit” and then press
“Enter”. Type “Y” and then press “Enter”.
42. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout” and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
INTEL (R) AMT POWER CONTROL
These configurations are effective only after AMT provisioning has started
Intel (R) AMT ON in Host Sleep States
<Desktop: ON in S0,
ME Wake in S3, S4-5>
Idle Timeout
65535
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Desktop : ON in S0
Desktop : ON in S0, ME Wake in S3, S4-5
Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
43. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout” and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0008/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
<ENTER> = Complete Entry
[ESC]= Discard Changes
64
Chapter 9 Intel AMT Settings
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising