DFI | EC510-SD/EC511-SD | manual | Dfi EC510-SD/EC511-SD Manual

Dfi EC510-SD/EC511-SD Manual
EC510/511-SD
User’s Manual
A47410911
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2017. All Rights Reserved.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Copyright.............................................................. 2
Chapter 4 - Jumper Settings.................................. 18
Trademarks........................................................... 2
Clear CMOS Data.................................................................... 18
FCC and DOC Statement on Class A...................... 2
Auto Power-on Select.............................................................. 18
COM1/COM2 RS232 Power Select (maindboard)...................... 19
About this Manual................................................. 4
COM1 /COM2 /COM3
Warranty ............................................................. 4
RS232/422/485 Select (mainboard)....... 20
Chapter 5 - Ports and Connectors.......................... 21
Static Electricity Precautions.................................. 4
Front Panel I/O Ports.............................................................. 21
USB Ports (mainboard)................................................................................ 21
COM (Serial) Ports (mainboard).................................................................... 22
9~36V DC-in............................................................................................... 22
RJ45 LAN Ports............................................................................................ 23
Display Interfaces........................................................................................ 23
Safety Measures................................................... 4
Safety Precautions................................................ 5
About the Package................................................ 5
I/O Connectors....................................................................... 24
Parallel Connector........................................................................................ 24
SATA (Serial ATA) Connectors....................................................................... 24
SATA (Serial ATA) Power Connectors............................................................. 25
SMBus Connector ....................................................................................... 25
Cooling Fan Connectors............................................................................... 26
Digital I/O Connector (mainboard)................................................................ 26
Audio Connector.......................................................................................... 27
Front Panel Connector ................................................................................ 27
S/PDIF Connector........................................................................................ 28
LPC Connector............................................................................................. 28
Expansion Slots........................................................................................... 29
12V DC-out................................................................................................. 30
Digital I/O Connector (daughter board)........................................................ 31
LAN Ports (daughter board)........................................................................ 31
Chapter 1 - Introduction........................................ 6
Overview..................................................................................6
Key Features............................................................................6
Specifications............................................................................7
Getting to Know the EC510/EC511-SD ......................................8
Mechanical Dimensions.............................................................9
Chapter 2 - Getting Started................................... 10
Chapter 3 - Installing the Devices.......................... 11
Chapter 6 - Mounting Options............................... 32
Removing the Chassis Cover.................................................... 11
Chapter 7 - BIOS Setup........................................ 33
Main........................................................................................................... 34
Advanced ................................................................................................... 34
Security....................................................................................................... 42
Boot........................................................................................................... 43
Exit............................................................................................................. 45
Installing a SODIMM............................................................... 12
Installing a 2.5” SATA Drive.................................................... 13
Installing a Mini PCIe or mSATA Card...................................... 14
Installing a PCI or PCIe Expansion Card................................... 15
Chapter 8 - Supported Software............................ 47
Installing a CPU...................................................................... 16
Chapter 9 - RAID ................................................. 63
Chapter 10 - Intel AMT Settings ........................... 67
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. Wear an antistatic wrist strap.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
4.
We will not be liable for any indirect, special, incidental or damages to the product that
has been modified or altered.
3. Do all preparation work on a static-free surface.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 EC510/EC511-SD system unit
• 1 CD disk includes: Drivers/Manual
• Danger of explosion if battery incorrectly replaced.
Optional Items
• Replace only with the same or equivalent type recommend by the manufacturer.
• Wall Mount kit
• Power Cord
• Power Adapter (100W/120W/160W)
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview
Model Name
EC510/EC511-SD
Processor
6th Generation Intel® CoreTM processors
Chipset
Intel® Q170 Chipset
LAN
6 LAN ports (or 4 PoE + 2 LAN ports)
COM
3 COM ports
Display
VGA
DVI (DVI-D signal) or HDMI by request
HDMI or DP (DP available upon request)
Front Panel
USB
4 USB 3.0 Type A ports
DIO
16-bit digital input/output
Power
9~36V DC-in
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
Processor
6th/7th Generation Intel® CoreTM Processors, LGA 1151 Socket
• Intel® Core™ i7-6700TE, Quad Core, 8M Cache, 2.4GHz (3.4GHz), 35W
• Intel® Core™ i5-6500TE, Quad Core, 6M Cache, 2.3GHz (3.3GHz), 35W
• Intel® Core™ i3-6100TE, Dual Core, 4M Cache, 2.7GHz, 35W
• Intel® Core™ i7-7700T, Quad Core, 8M Cache, 2.9GHz (3.8GHz), 35W
• Intel® Core™ i5-7500T, Quad Core, 6M Cache, 2.7GHz (3.3GHz), 35W
• Intel® Core™ i3-7101TE, Dual Core, 3M Cache, 3.4GHz, 35W
Chipset
Intel® Q170 Chipset
Memory
Two 260-pin SODIMM
• Supports dual-channel DDR4 1866/2133MHz
• Supports up to 32GB system memory
Graphics
Intel® HD Gen 9 Graphics
OpenGL 5.0, DirectX 12, OpenCL 2.1
• Supports these codecs:
Front I/O Ports
Power
Fanless with heatsink
Environment
• Operating Temperature:
0 to 50°C (SSD or mSATA-mini, with 0.7m/s air flow)
• Storage Temperature:
-20 to 85°C
• Relative Humidity:
5 to 95% RH (non-condensing)
Construction
• Aluminum + SGCC
VGA (+)
DVI-I (DVI-D signal) / HDMI (HDMI available upon request) (+)
HDMI / DP (DP available upon request)
Mounting
• Wall mount
- Mounting brackets and screws (optional)
• Two 2.5" SATA Drive Bay
• SATA 3.0 port with data transfer rate up to 6Gb/s
Dimensions
• 235mm x 102.5mm x 222mm (W x H x D)
Weight
• 4.1 kg
OS Support
• Windows 7 (32/64-bit)
• Windows 8.1 (64-bit)
• Windows 10
Other Features
System Reset, Programmable via Software from 1 to 255 Seconds
Standards and
Certifications
• Shock:
Half sine wave 3G, 11ms, 3 shock per axis
• Vibration: IEC68-2-64
• Output displays:
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I: resolution up to 1920x1200 @ 60Hz
HDMI: resolution up to 4096x2160 @ 24Hz or 2560x1600 @ 60Hz
DP: resolution up to 4096x2304 @ 60Hz
Storage
Ethernet
Expansion
Power input voltage: 9~36V DC-in (terminal block connector)
Cooling System
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/
H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Triple/Dual
Display
- One status and one HDD LED
- One power button with LED
- One reset button
- Six RJ45 LAN ports; four of these six can be PoE GbE (RJ-45) (supports
IEEE 802.3af, 15.4W per port)
- One VGA port/one DVI (DVI-D signal)/one HDMI or DP
(DP available upon request)
- Four USB 3.0 Type A ports
- One Line-out and one Mic-in Ports
- Two RS-232/422/485 (DB-9) (RS-232 with power) and
one RS-232/422/485 (DB-9)
- Two set of 8-bit DIO
- One 9~36V DC-in 3-pole terminal block
• One Intel® I211AT PCIe (10/100/1000Mbps)
• One Intel® I219V
• Four Intel® I210IT PCIe (10/100/1000Mbps) for Gigabit Ethernet or
PoE ports
One full-size Mini PCIe (PCIe/USB)
One half-size Mini PCIe (USB/mSATA)
1 x PCI slot (EC510-SD)
1 x PCIe x16 slot (EC511-SD)
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the EC510/EC511-SD
Front I/O Ports
Front View
Power Button with LED (Green)
Press to power on or power off the system.
DVI-I HDMI(2)
(DVI-D signal)
USB 3.0
LAN1 LAN2
DC-in
Reset Button
Press to reset the system.
Status LED (Orange)
HDD LED (Red)
Reset
HDD LED (Red)
Indicates the status of disk drives.
Power Button(1)
with LED (Green)
HDD LED
Digital IO
Mic-in, Line-out
PoE 1~4
or
LAN 3~6
HDD State
Disk access
activity
LED Behavior
Blink
Disk drives present or not present
Off
Status LED (Orange)
Indicates system status as below.
Expansion slot
COM1
COM3
VGA
Status LED
Remote power on/off
COM2
Suspend Mode
S0
Sleep
S4, S5
LED Behavior
Always ON
Blinking
Off
Rear View
Remote Power-on/Power-off Switch Connector
Connects distant power on/off switch.
USB 3.0 Ports
Connect to USB 3.0 as well as devices based on previous USB versions.
COM Ports
All COM ports can be selected among RS232, RS422 and RS485.
COM1 and COM2 can be selected between RS232 and RS232 with power via jumper settings.
DIO Connector
The DIO connector provides 16-bit digital input/output.
DVI-I (DVI-D signal) / HDMI / VGA Connector
Connects the DVI-I / HDMI / VGA connector of an LCD monitor.
Line-out and Microphone Ports
Connect audio devices such as microphones and speakers.
Notes:
1. Please gently press the power button to avoid possible damages.
Gigabit LAN Ports (1~6)
Connect the system to a local area network.
LAN 3~6 can be Power over Ethernet (PoE) that is capable of delivering 15.4W of power to
connected devices.
2. The HDMI is a DP/HDMI combo port but can only transmit HDMI signals (unless wired as a DP
port by request). Please plug in an HDMI cable with the right orientation and alignment to avoid
damage to the connector. You should feel resistance (due to a pin on the right) if the cable is not
inserted correctly.
Aligning side
(left)
Angled-corner
Angled-corner
pin
(up)
DC-in
DC 9~36V power input via a terminal block connector.
Align this edge with the
left side of the connector
PCIe Expansion Slot
Provides PCIe or PCI expansion connectivity via a riser card.
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
Chassis Dimensions
Motherboard Dimensions
209.55
Rear View
221.20
216.70
Gold finger
PCIE X4
Gold finger
PCIE X16
235
Right View
228
102.50
Left View
50
mini PCIe
Front View
9
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
•
SATA hard drive
AC power adapter
Optical drive (for installing software/drivers)
Memory module
Installing Devices
The following devices can be installed in the system.
•
•
•
•
Memory module
SATA hard drives
Mini PCIe and mSATA card
PCIe or PCI expansion cards
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1.
2.
Power-on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing an Operating System
To install an OS, you need an optical drive or a USB flash drive and boot from such a device.
Make sure a 2.5” SATA drive is already installed.
1.
2.
Refer to the following chapters for information on installing SATA drives.
Refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
10
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing the Devices
4.
Removing the Chassis Cover
1.
Make sure the system and all other peripherals connected to it have been powered off.
2.
Disconnect all power cords and cables.
3.
The 6 mounting screws on the left and right sides and bottom of the system are used to
secure the cover to the chassis. Remove these screws and put them in a safe place for
later use.
Lift the cover upward to open the system.
Chassis screw
Chassis screw
Chassis screw
11
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a SODIMM
To remove a SODIMM, gently spread the retaining clips at each end of the SODIMM
socket. The SODIMM should pop out of the socket. Lift the SODIMM away from the socket
on the mainboard.
Grasp the module by its edges and align the SODIMM’s notch with the socket’s key; then
insert the SODIMM into the socket at an angle and push it down until the retaining clips
snap into place.
DIMM2
DIMM1
DIMM2
DIMM1
Spread the retaining clips
to release the installed
SODIMM
Notes:
1. The system supports dual-channel configuration. To enable dual-channel,
populate both SODIMM sockets.
2. If you plan to install only one SODIMM, install it in the DIMM1 socket (lower
one and farther from the center of the mainboard).
3. The SODIMM sockets can only accept DDR4 memory modules. Please do not
install other types of memory modules.
12
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a 2.5” SATA Drive
1.
3.
The SATA HDD bracket is included in the product package. Locate the SATA drive bay on
which the SATA HDD bracket will be mounted.
Place the SATA drive with the HDD bracket into the system. Align the mounting holes on the
HDD bracket with the mounting holes on the SATA drive bay and use the provided screws to
secure the drive in place.
Mounting Screws
SATA drive bay
2.
Insert the SATA drive into the HDD bracket and secure it in place with the provided screws
(black screws). The HDD bracket can accommodate two SATA drives.
4.
Mounting screws
Mounting screw
Connect the other end of the SATA data cable and the SATA power cable to the SATA data and
SATA power connector on the mainboard respectively.
Mounting screw
SATA cables
SATA data connector
Note:
Connect SATA cables before affixing the SATA drive on the HDD bracket as the HDD
bracket would prevent access to the SATA connectors of the drive.
SATA power connector
13
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a Mini PCIe or mSATA Card
The Mini PCIe sockets are located on the mainboard. You need to revmove the riser card and
daughter board to access them.
The mainboard is equipped with 2 Mini PCIe slots: one full-size and one half-size slot. Here we
will demonstrate the installation of a full-size Mini PCIe card.
The 2 mounting screws on the supporting bracket of the riser card are used to secure
the riser card to the chassis. Remove these screws and put them in a safe place for later
use. To disengage the riser card from the mainboard, gently pull the card out of the
connector on the mainboard.
The 4 mounting screws on the daughter board are used to secure the board to the
mainboard. Remove these screws and put them in a safe place for later use. To
disengage the daughter board from the mainboard, gently pull the card out of the
connector on the mainboard.
1.
Grasp the Mini PCIe card by its edges and align the notch in the connector of the Mini
PCIe card with the connector's key on the mainboard.
2.
Secure the card on the mainboard with the provided mounting screw.
3.
If the Mini PCIe card has antennas, route the antennas to the antenna holes on the
rear chassis of the device.
Mounting screw
on the riser card
Wireless antenna
Mounting screw
Note:
The system also has a half-size Mini PCIe slot that can accommodate a Mini PCIe
card using mSATA or USB signals.
Important:
The bottom side of a full-size Mini PCIe module should have a component height
restriction of 0.82 mm and will sit flush against the connected half-size Mini PCIe
module if such a component is used and the half-size slot is connected with a module.
Mounting screw
on the daughter board
0.82mm
14
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a PCI or PCIe Expansion Card
2. Insert the expansion card into a PCI or PCIe slot on the riser card. Ensure the card is properly
seated into the slot and secure the bracket in place.
Important:
When inserting expansion cards into the system, please select a standard card
within 167.65mm (as shown in the picture below) in order to fit into the expansion slot.
PCI card
1.
Front View
The PCI and PCIe slots on the riser card inside the system are used to install expansion
cards. To install an expansion card you need to first remove the slot plate and bracket by
uninstalling the screw on the front chassis.
Slot plate
Note:
The EC511-SD has one PCIe x16 slot with the H120-1E riser card, whereas the EC510SD has one PCI slot with the H320-1P riser card.
Mounting screw and bracket
15
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a CPU
6. Remove the protective cap from the CPU socket. The cap is used to protect the CPU socket against dust and harmful particles. Remove the protective cap only to install the CPU.
1. Make sure the system and all other peripheral devices connected to it have been powered-off.
2. Disconnect all power cords and cables.
7. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as the photo shown below.
3. Before installing the Intel CPU, remove the 8 mounting screws on the top of the
system unit and put them in a safe place for later use.
8. Unlock the socket by pushing the load lever down and moving it sideways until it is released from the retention tab and then lift the load lever up.
Load lever
Protective
cap
Load plate
Retention tab
9. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as shown below. The CPU’s notch will at the same time fit into
the socket’s alignment key.
4.
The system board is equipped with a surface mount LGA 1151 socket. This socket is exclusively designed for installing a LGA 1151 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1151 socket comes with a protective cap, (2) the cap is not damaged and (3) the socket’s contact pins are not
bent. If the cap is missing or the cap or contact pins are damaged, contact
your dealer immediately.
2. Keep the protective cap. RMA requests will be accepted and processed only if
the LGA 1151 socket comes with the protective cap.
5. Unlock the socket by pushing the load lever down, move it sideways until it is released
from the retention tab, and then lift the load lever up.
Alignment key
Gold triangular mark
16
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
10. Close the load plate and push the load lever down to lock it under the retention tab. While
closing the load plate, slide the front edge of the load plate under the retention tab.
Retention knob
17
Chapter 3 Installing the Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
Auto Power-on Select
Clear CMOS Data
2
10
1
9
Parallel
2
26
S/PDIF 1
Power
Button
Status LED
HDD LED
3
2
1
1-2 On: Normal
(default)
DIO
1
2
10
1
9
Parallel
2
26
Front Audio
Front Audio
1
5
2
12
1
Auto Power-on
Select (JP11) 1
DIO Power
S/PDIF 1
Power
Button
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
Front 1
Panel
DIO
1
Status LED
HDD LED
DDR4_1 SODIMM
5
2
12
1
25
Front 1
Panel
DDR4_1 SODIMM
1
mSATA
JP1
System
Fan 1
1
mSATA
LAN 2
System
Fan 1
bettery
Clear CMOS
Data (JP1)
LAN 1
1
(JP9)
6
SPI Flash
BIOS
USB 3-4 USB 3.0
14
2
2-3 On: Clear CMOS Data
LPC
1
2
1
10
1
2
9
10
USB 3-4 USB 3.0
COM 2
1
1
1
4
2
SATA Power
System
Fan 2
3
1
1
2
DC-in
PCIe x16 (PCIE1)
1
1
1
(JP5) (JP12)
6
6
1
4
6
2 1
2 1
J21
6
2
1
1
9
3
VGA
J22
2
4
System
Fan 2
16
JP3
JP2
1
SATA Power
+
+
4-pin power
1
6
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
COM 1
4
1
2
DC-in
PCIe x16 (PCIE1)
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
1
PCIe x4 (PCIE2)
9
10
1
9
(JP7) (JP14)
6
6
DVI
10
1
10
1
2
COM 2
1
SATA 0
1
1
1
2
2-3 On:
Power-on via AC power
COM 3
1
1
1
(JP5) (JP12)
6
6
DVI
4
LPC
HDMI (default)/DP
2
1
1
(JP6) (JP13)
6
6
1
1
14
2
SATA 3.0
SATA 1
SATA 0
1
(JP8) (JP15)
6
6
2
1
9
(JP7) (JP14)
6
6
1 2 3
(JP9)
6
SPI Flash
BIOS
USB 1-2 USB 3.0
COM 3
HDMI (default)/DP
1
ECX
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
3
2
1
Clear CMOS
Data (JP1)
1
1
ECX
1-2 On:
Power-on via the
power button (default)
DDR4_2 SODIMM
1
bettery
LAN 1
1 2 3
Mini PCIe
DDR4_2 SODIMM
LAN 2
JP11
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
Mini PCIe
1
6
6
2 1
2 1
JP3
JP2
J21
6
2
16
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
-
-
If you encounter the following conditions, you can reconfigure the system with the default values stored in the ROM BIOS.
JP11 is used to select the method of powering on the system. If you want the system to
power-on whenever AC power comes in, set JP11 pins 2 and 3 to On. If you want to use the
power button, set pins 1 and 2 to On.
a) CMOS data becomes corrupted.
When using the JP11 “Power On” feature to power the system back on after a power failure
, the system may not power on if the power lost is resumed within 5 seconds (power flicker).
b) You forgot the supervisor or user password.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power-off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper back to its
default setting: 1-2 On.
3. Now plug the power cord and power on the system.
18
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
COM1/COM2 RS232 Power Select
2
10
1
9
Parallel
2
26
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
1
5
2
12
1
Reset
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
System
Fan 1
bettery
LAN 1
1
Clear CMOS
Data (JP1)
1
ECX
(JP9)
6
SPI Flash
BIOS
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 3-4 USB 3.0
14
LPC
2
9
10
1
9
(JP7) (JP14)
6
6
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
1
1
1
(JP5) (JP12)
6
6
DVI
1
4
1
4
SATA Power
System
Fan 2
3
+
DC-in
1
10
1
2
COM 2
1
HDMI (default)/DP
1
1
2
COM 3
2
10
1
9
COM 1
4
6
4-pin power
1
1
1
1
JP3
JP2
2
PCIe x16 (PCIE1)
J21
6
2
16
6
2 1
2 1
1
VGA
J22
1
2
1
PCIe x4 (PCIE2)
-
JP2
6
2
JP3
6
1
2
1
1-3 (RI), 2-4 (DCD) On: 3-5 (+5V), 4-6 (+12V) On:
RS232 (default)
RS232 with power
JP3 (for COM1) and JP2 (for COM2) are used to configure serial COM ports to normal RS232
or RS232 with power. The pin assignments (Pin 1: optional 12V and Pin 9: optional 5V) of
COM1 and COM2 will vary according to JP3’s and JP2’s setting respectively.
19
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Status LED
HDD LED
2
12
DDR4_1 SODIMM
6
JP9
4
JP8, JP15 2
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
System
Fan 1
5
3
1
Clear CMOS
Data (JP1)
COM2:
RS232/422/485 Select
1
ECX
(JP9)
6
SPI Flash
BIOS
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
2
LPC
1
10
1
2
9
10
6
JP7, JP14
4
JP13
2
5
3
1
1
9
(JP7) (JP14)
6
6
2
2
1
1
(JP6) (JP13)
6
6
1
1
1
1
(JP5) (JP12)
6
6
DVI
1
4
1
4
SATA Power
System
Fan 2
3
1
4
+
6
6
2 1
2 1
J21
6
2
10
1
9
DATA+
DATAN.C.
N.C.
N.C.
RS485
9
2
1
2
1
9
9
16
JP3
JP2
2
PCIe x16 (PCIE1)
DC-in
2
2
1
COM1/COM2/COM3:
RS232/422/485
COM 1
4-pin power
1
1
1
RS422
Full Duplex
COM1 / COM2 / COM3
COM 2
1
SATA 3.0
SATA 1
SATA 0
1
1
2
COM 3
HDMI (default)/DP
6789
RS232
DCD
TXD
GND
RTS
RI
USB 3-4 USB 3.0
14
6789
RXD
DTR
DSR
CTS
1
1 2345
6789
bettery
LAN 1
1 2345
COM3:
RS232/422/485 Select
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
Front 1
Panel
DATANC.
NC.
NC.
1
5
1
DATA+
TXD
NC.
NC.
NC.
DIO
N.C.
N.C.
N.C.
N.C.
1 2345
26
DSR
RTS
CTS
RI
(or +5V)
S/PDIF 1
Power
Button
RXD+
RXDTXD+
TXDN.C.
Parallel
2
1
N.C.
N.C.
N.C.
N.C.
9
Front Audio
RXDTXDNC.
NC.
10
COM1 / COM2 / COM3
RXD+
TXD+
NC.
NC.
NC.
2
1
RS232/422/485 Select
DCD
(or +12V)
RXD
TXD
DTR
GND
COM1 /COM2 /COM3
1
2
RS422
Full Duplex
RS232
VGA
J22
1
1
PCIe x4 (PCIE2)
RS485
JP6 (for COM1) / JP13 (for COM2) / JP9 (for COM3)
-
JP6
JP5, JP12
5
3
1
6
4
2
COM1:
RS232/422/485 Select
6
5
4
3
2
1
6
4
2
1-2 On: RS232
(default)
5
3
1
6
4
2
3-4 On: RS422
Full Duplex
5
3
1
5-6 On: RS485
JP5 and JP12 (for COM1) / JP7 and JP14 (for COM2) /JP8 and JP15 (for COM3)
These jumpers allow you to configure the serial COM ports to RS232, RS422 (full duplex) or
RS485. JP5, JP6 and JP12 are used to configure serial COM port 1. JP7, JP13 and JP14 are
used to configure serial COM port 2. JP8, JP9 and JP15 are used to configure serial COM port
3. The pin functions of COM port 1 to COM port 3 will vary according to these jumpers’ settings. In addition, COM port 1 and COM port 2 can be switched between normal RS232 and
RS232 with power. You can also configure the RS485 auto flow mechanism with the BIOS
setup utility. For more information, refer to Chapter 7.
6
4
2
5
3
1
1-3, 2-4 On:
RS232 (default)
6
4
2
5
3
1
3-5, 4-6 On:
RS422 Full Duplex/RS485
Notes:
1. When COM1 RS232/422/485 is selected, JP5 and JP12 must be set in accordance to JP6.
2. When COM2 RS232/422/485 is selected, JP7 and JP14 must be set in accordance to JP13.
3. When COM3 RS232/422/485 is selected, JP8 and JP15 must be set in accordance to JP9.
20
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Front Panel I/O Ports
2
10
1
9
Parallel
2
VCC
-Data0
+Data0
GND
GND
USB Ports
USB 2.0
USB 9
1
USB 2.0
USB 13/14
26
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
DVI-I
1
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
10
9
DDR4_1 SODIMM
1
mSATA
LAN 1
1
Clear CMOS
Data (JP1)
1
ECX
(JP9)
6
SPI Flash
BIOS
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 3-4 USB 3.0
14
2
LPC
9
10
1
1
(JP5) (JP12)
6
6
1
4
1
4
SATA Power
System
Fan 2
Remote power on/off
3
+
2
2
10
1
9
COM 1
4
PCIe x16 (PCIE1)
DC-in
1
1
1
4-pin power
1
1
USB 1-2
USB 3-4
2
2
1
1
(JP6) (JP13)
6
6
1
DVI
COM2
1
10
1
2
1
9
(JP7) (JP14)
6
6
1
VGA
10
9
COM 2
1
SATA 3.0
SATA 1
SATA 0
Expansion slot
1
2
COM 3
HDMI (default)/DP
COM1
COM3
2
1
System
Fan 1
bettery
Mic-in, Line-out
PoE 1~4(1)(2)
or
LAN 3~6
25
Mini PCIe
LAN 2
Reset
Power Button
with LED (Green)
Digital IO
12
DDR4_2 SODIMM
Status LED (Orange)
HDD LED (Red)
LAN1 LAN2
2
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
USB 3.0
1
VCC
-Data0
+Data0
GND
Key
DC-in
HDMI
5
VCC
-Data1
+Data1
GND
N.C
Chapter 5 - Ports and Connectors
6
6
2 1
2 1
JP3
JP2
J21
6
2
16
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
-
The front panel I/O consists of the following ports from the mainboard:
• Status and control: power button with LED, reset button, remote power on/off
switch connector, status and HDD LEDs
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals. In addition to the 4 external ports on the
front panel, the system board provides 3 USB 2.0 ports through internal pin headers.
• Power: DC-in
• USB: four USB 3.0 ports
• Serial: three RS232 serial COM ports
• Audio: one Line-out and one Mic-in port
•
• Network: two RJ45 LAN ports
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
• Display: VGA/DVI-I (DVI-D signal)/HDMI ports
BIOS Setting
• PCIe expansion: PCIe or PCI slot
The front panel I/O consists of the following ports from the daughter board:
• Network: four RJ45 LAN ports (or PoE ports)
• Digital input/output: one 16-bit DIO connector
21
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
9~36V DC-in
COM (Serial) Ports
2
10
1
9
Parallel
2
26
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
2
10
1
9
Parallel
2
26
Front Audio
Front Audio
1
5
2
12
1
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
S/PDIF 1
Power
Button
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
DIO
1
Status LED
HDD LED
DDR4_1 SODIMM
2
12
1
25
Front 1
Panel
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
DDR4_2 SODIMM
1
mSATA
LAN 2
System
Fan 1
1
mSATA
LAN 2
1
System
Fan 1
bettery
bettery
LAN 1
Clear CMOS
Data (JP1)
LAN 1
1
(JP9)
6
SPI Flash
BIOS
ECX
2
LPC
1
10
1
2
9
10
USB 3-4 USB 3.0
COM 3
COM 2
1
HDMI (default)/DP
1
1
(JP5) (JP12)
6
6
DVI
4
1
4
System
Fan 2
3
1
1
1
6
6
2 1
2 1
JP3
JP2
J21
6
2
1
1
1
1
(JP5) (JP12)
6
6
4
2
1
4
SATA Power
System
Fan 2
9
-
1
PCIe x4 (PCIE2)
3
DC-in
1
DC-in
6
2
PCIe x16 (PCIE1)
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
JP3
JP2
J21
6
2
16
6
2 1
2 1
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
-
-
COM1 to COM3 can be selected among RS232, RS422 and RS485 via jumper settings. In addition, COM1 and COM2 can be switched between normal RS232 and RS232 with power. For pin
definitions and jumper selection for different communication modes, please refer to Chapter 4.
This three-pole terminal block connector terminal block connector provides options of power
input solution: 100W, 120W, and 160W. Connect a DC power cord to this jack. Using a voltage higher than the recommended one may fail to boot the system or cause damage to
the mainboard.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
•
1
1
VGA
J22
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
DVI
16
9
10
1
9
(JP7) (JP14)
6
6
SATA 0
+
+
2
PCIe x16 (PCIE1)
DC-in
10
1
10
1
2
COM 2
1
1
COM1 to COM3:
RS232/RS422/RS485
1
2
COM 3
COM 1
4
4-pin power
1
1
1
2
SATA Power
LPC
HDMI (default)/DP
2
1
1
(JP6) (JP13)
6
6
1
1
14
2
SATA 3.0
SATA 1
SATA 0
1
1
(JP8) (JP15)
6
6
2
1
9
(JP7) (JP14)
6
6
+
14
1
2
(JP9)
6
SPI Flash
BIOS
USB 1-2 USB 3.0
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 3-4 USB 3.0
Clear CMOS
Data (JP1)
1
1
ECX
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
Mini PCIe
1
5
BIOS Setting
Configure the serial ports with more advanced options such as the RS485 auto flow mechanism in the Advanced menu (“Super IO Configuration” submenu) of the BIOS. Refer to Chapter
7 for more information.
22
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
RJ45 LAN Ports (mainboard)
Display Interfaces
VGA
2
Parallel
2
10
26
GND
VSYNC_C
VGA_SDA
GND
GND
VGA_DET
NC
VGA_GREEN_C
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
1
9
5
1
2
12
1
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
Front 1
Panel
DDR4_1 SODIMM
Mini PCIe
LAN2
DDR4_2 SODIMM
LAN1
1
mSATA
LAN 2
System
Fan 1
bettery
LAN 1
1
Clear CMOS
Data (JP1)
2 1
1
2
10
1
9
Parallel
2
26
Front Audio
VGA_SCL
HSYNC_C
NC
5V
GND
GND
VGA_BLUE_C
VGA_RED_C
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
1
5
2
12
1
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
System
Fan 1
bettery
LAN 1
1
LAN1
LAN2
(JP9)
6
SPI Flash
BIOS
14
2
LPC
1
2
1
10
1
2
9
10
11
USB 3-4 USB 3.0
COM 3
HDMI or DP
1
9
(JP7) (JP14)
6
6
2
SATA 3.0
SATA 1
SATA 0
1
4
1
4
SATA Power
System
Fan 2
2
10
1
+
1
4
6
4-pin power
PCIe x16 (PCIE1)
6
JP3
JP2
J21
6
2
2 1
2 1
1
9
J22
2
4
System
Fan 2
3
DC-in
2
PCIe x16 (PCIE1)
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
6
6
2 1
2 1
J21
6
2
16
JP3
JP2
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
1
PCIe x4 (PCIE2)
-
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
Features
•
•
1
SATA Power
1
VGA
1
1
1
(JP5) (JP12)
6
6
4
-
DC-in
2
1
1
+
3
1
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
DVI
16
9
10
1
9
(JP7) (JP14)
6
6
SATA 0
COM 1
1
10
1
2
COM 2
1
HDMI (default)/DP
DVI-I
1
2
COM 3
1
1
1
LPC
1
1
1
(JP5) (JP12)
6
6
DVI
14
2
1
1
(JP6) (JP13)
6
6
1
1
1
(JP8) (JP15)
6
6
2
COM 2
1
HDMI (default)/DP
(JP9)
6
SPI Flash
BIOS
USB 1-2 USB 3.0
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 3-4 USB 3.0
Clear CMOS
Data (JP1)
1
ECX
1
ECX
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
Front 1
Panel
DVI-I (DVI-D Signal) Port
LAN1: Intel® I219V Gigabit Ethernet Controller
LAN2: Intel® I211AT Gigabit Ethernet Controller
The DVI-I (DVI-D Signal) port is used to connect a digital LCD monitor to transmit uncompressed digital video. This connector has a DVI-I receptacle but implements DVI-D signals
(digital only).
The LAN ports allow the system to connect to a local area network via Ethernet.
BIOS Setting
Connect the display device’s cable connector to the DVI-I port. After you plug the cable connector into the DVI-I port, gently tighten the cable screws to hold the connector in place.
Configure the onboard LAN in the Advanced menu (“ACPI Configuration”) of the BIOS.
Refer to Chapter 7 for more information.
HDMI Port or DisplayPort
Driver Installation
The HDMI port which carries both digital audio and video signals and is used to connect the
HDMI port of an LCD monitor or a digital TV.
Install the LAN drivers. Refer to Chapter 8 for more information.
BIOS Setting
Configure the display devices in the Advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
Driver Installation
Install the graphics driver. Refer to Chapter 8 for more information.
23
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
I/O Connectors
SATA (Serial ATA) Connectors
Parallel Connector
2
10
1
9
Parallel
2
26
Front Audio
Power
Button
26
25
2
1
S/PDIF 1
DIO
1
Status LED
HDD LED
1
5
2
12
1
Reset
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
LPT
System
Fan 1
bettery
10
1
9
Parallel
2
26
LAN 1
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
5
1
2
12
1
ECX
DDR4_1 SODIMM
1
mSATA
USB 3-4 USB 3.0
System
Fan 1
1
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
1
1
1
(JP5) (JP12)
6
6
1
1
2
1
10
1
2
9
10
4
1
4
SATA Power
System
Fan 2
1
1
1
2
10
1
9
COM 1
SATA 0/1
7
1
SATA 3.0 6Gb/s
COM 3
3
COM 2
1
1
9
(JP7) (JP14)
6
6
HDMI (default)/DP
2
SATA 3.0
SATA 1
SATA 0
DC-in
1
1
(JP6) (JP13)
6
6
1
1
1
1
4
4
SATA Power
System
Fan 2
3
4
+
6
6
2 1
2 1
2
10
1
9
PCIe x16 (PCIE1)
J21
6
2
1
1
2
EPP
(Enhanced Parallel Port)
2
2 1
2 1
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
Features
1
PCIe x4 (PCIE2)
-
ECP
(Extended Capabilities Port)
6
VGA
J22
The 25-pin connector is used to connect the parallel port of a device such as a printer. It supports SPP, ECP and EPP standards.
SPP
(Standard Parallel Port)
JP3
JP2
J21
16
JP3
JP2
2
DC-in
PCIe x16 (PCIE1)
COM 1
4-pin power
1
2
16
6
1
1
1
6
-
1
1
(JP5) (JP12)
6
6
DVI
1
1
2
4
4-pin power
+
2
LPC
9
10
1
9
(JP7) (JP14)
6
6
DVI
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
1
10
1
2
COM 2
1
SATA 0
(JP9)
6
1
2
COM 3
1
SPI Flash
BIOS
14
LPC
HDMI (default)/DP
Clear CMOS
Data (JP1)
1
ECX
14
2
bettery
LAN 1
1
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
DDR4_2 SODIMM
USB 3-4 USB 3.0
(JP9)
6
SPI Flash
BIOS
Mini PCIe
LAN 2
Clear CMOS
Data (JP1)
1
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
Front 1
Panel
1
GND
TXP
TXN
GND
RXN
RXP
GND
2
Front Audio
•
2 Serial ATA 3.0 ports
- SATA port 0 and 1 with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller with Intel® RST
The Serial ATA connectors are used to connect the Serial ATA device. Connect one end of the
Serial ATA data cable to a SATA connector on the mainboard and the other end to your Serial
ATA device.
Allows normal speed operation but in one
direction only.
The power cable must be connected from the mainboard’s Serial ATA power connector to a
SATA drive’s power connector in order to provide power to the drive. Refer to the next page
for pin definitions of the SATA power connectors.
Allows parallel port to operate in bidirectional
mode and at a speed faster than the SPP’s data
transfer rate.
BIOS Setting
Allows bidirectional parallel port operation at
maximum speed.
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
24
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
SATA (Serial ATA) Power Connectors
2
10
1
9
Parallel
2
SMBus Connector
26
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
2
10
1
9
Parallel
2
26
Front Audio
1
5
2
12
1
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
S/PDIF 1
Power
Button
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
25
DIO
1
Status LED
HDD LED
DDR4_1 SODIMM
2
12
1
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
Mini PCIe
1
5
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
DDR4_2 SODIMM
System
Fan 1
1
mSATA
LAN 2
bettery
LAN 1
1
System
Fan 1
bettery
Clear CMOS
Data (JP1)
LAN 1
1
1
ECX
1
(JP9)
6
SPI Flash
BIOS
ECX
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
14
2
LPC
1
2
1
10
1
2
9
10
COM 3
USB 3-4 USB 3.0
COM 2
1
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
1
1
1
(JP5) (JP12)
6
6
DVI
1
4
1
4
System
Fan 2
3
DC-in
1
2
PCIe x16 (PCIE1)
6
6
2 1
2 1
JP3
JP2
J21
6
2
1
1
2
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
1
1
(JP5) (JP12)
6
6
DVI
1
4
1
4
SATA Power
System
Fan 2
1
VGA
J22
4
3
1
1
DC-in
PCIe x4 (PCIE2)
9
10
1
9
(JP7) (JP14)
6
6
9
16
1
10
1
2
COM 2
1
1
10
1
2
COM 3
COM 1
4
4-pin power
1
SATA
Power 0/1
+
+
1
1
1
14
LPC
HDMI (default)/DP
1
2
SATA Power
1
(JP8) (JP15)
6
6
2
1
9
(JP7) (JP14)
6
6
HDMI (default)/DP
(JP9)
6
SPI Flash
BIOS
USB 1-2 USB 3.0
+12V
Ground
Ground
+5V
USB 3-4 USB 3.0
Clear CMOS
Data (JP1)
2
PCIe x16 (PCIE1)
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
6
6
2 1
2 1
JP3
JP2
J21
6
2
16
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
-
-
SMBus
NC
SMBUS Data
GND
65
2 1
SMBUS_Alert
SMBUS Clock
+3.3V_standby
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each
one to act as a master by initiating data transfer.
These SATA power connectors supply power to SATA drives. Connect one end of the provided
power cable to the SATA power connector and the other end to your storage device.
25
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Cooling Fan Connectors
2
10
1
9
Parallel
2
Digital I/O Connector (mainboard)
26
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
2
10
1
9
Parallel
2
26
5
2
12
1
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
1
1
5
Clear CMOS
Data (JP1)
2
12
25
Front 1
Panel
1
mSATA
LAN 2
System
Fan 1
(JP9)
6
LPC
1
2
9
10
1
9
(JP7) (JP14)
6
6
1
1
(JP5) (JP12)
6
6
1
4
1
4
SATA Power
System
Fan 2
3
1
1
1
1
USB 3-4 USB 3.0
1
(JP8) (JP15)
6
6
14
2
3
LPC
PCIe x16 (PCIE1)
10
1
9
6
6
2 1
2 1
J21
6
2
1
J22
1
2
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
1
1
1
(JP5) (JP12)
6
6
DVI
1
4
1
4
SATA Power
System
Fan 2
3
VGA
1
1
1
1
1
2
10
1
9
COM 1
4
4-pin power
1
DC-in
PCIe x4 (PCIE2)
9
10
1
9
(JP7) (JP14)
6
6
SATA 0
16
JP3
JP2
1
10
1
2
COM 2
1
1
System
Fan 2
1
2
COM 3
HDMI (default)/DP
+
+
2
2
COM 1
4
4-pin power
1
Ground
Power
Sense
2
1
1
(JP6) (JP13)
6
6
1
(JP9)
6
SPI Flash
BIOS
USB 1-2 USB 3.0
2
SATA 3.0
SATA 1
DVI
DC-in
1
10
COM 2
1
HDMI (default)/DP
1
1
2
COM 3
SATA 0
DIO5 DIO3 DIO1
Clear CMOS
Data (JP1)
ECX
1
(JP8) (JP15)
6
6
1
1
bettery
1
DIO0
1
SPI Flash
BIOS
2
DIO6 DIO4
DIO7
DDR4_1 SODIMM
Mini PCIe
LAN 1
USB 1-2 USB 3.0
14
DIO2
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
1
ECX
Auto Power-on
Select (JP11) 1
DIO Power
DDR4_2 SODIMM
System
Fan 1
System
Fan 1
bettery
LAN 1
1
1
1
Reset
DDR4_2 SODIMM
mSATA
DIO
Status LED
HDD LED
DDR4_1 SODIMM
Mini PCIe
LAN 2
S/PDIF 1
Power
Button
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
USB 3-4 USB 3.0
DIO
Front Audio
1
2
PCIe x16 (PCIE1)
6
6
2 1
2 1
J21
6
2
16
JP3
JP2
1
VGA
J22
1
2
1
PCIe x4 (PCIE2)
-
-
The fan connectors are used to connect cooling fans.
The Digital I/O connector provides 8 digital input or output port to enable monitor and control
of the states of the connected external devices. Note that the HW Utility can only configure
the external DIO ports. Please see “Digital I/O Connector (daughter board)” in this chapter.
BIOS Setting
Digital I/O Connector
The Super IO menu (“PC Health Status” submenu) of the BIOS will display the current speed
of the cooling fans. Refer to Chapter 7 for more information.
Pins
DIO
1
DIO7
2
DIO6
3
DIO5
4
DIO4
5
DIO3
6
DIO2
7
DIO1
8
DIO0
26
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Audio Connector
Front Panel Connector
2
10
1
9
Parallel
2
26
Front Panel
Front Audio
Power
Button
Front Audio
2
10
1
9
Parallel
2
S/PDIF 1
DIO
1
Status LED
HDD LED
GND
NC
Mic-JD
NC
Line-JD
2
12
25
Front 1
Panel
12
5 2
USB 2.0 9 1
USB 2.0 13-14 1
1
mSATA
LAN 1
System
Fan 1
1
LAN 1
1
Clear CMOS
Data (JP1)
Mic-L
Mic-R
Line-R
GND
Line-L
(JP9)
6
SPI Flash
BIOS
USB 3-4 USB 3.0
14
2
LPC
1
2
1
10
1
2
9
10
14
LPC
1
1
4
1
4
1
1
(JP5) (JP12)
6
6
DVI
1
4
System
Fan 2
3
1
6
PCIe x16 (PCIE1)
9
J21
6
2
JP3
2 1
2 1
1
1
VGA
J22
2
PCIe x16 (PCIE1)
DC-in
16
6
JP2
2
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
1
6
6
2 1
2 1
JP3
JP2
J21
6
2
16
1
VGA
J22
1
2
1
PCIe x4 (PCIE2)
-
+
2
10
1
3
COM 1
4
4-pin power
1
2
4
System
Fan 2
1
1
1
SATA Power
+
SATA Power
DC-in
1
1
1
(JP5) (JP12)
6
6
DVI
1
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
9
10
1
9
(JP7) (JP14)
6
6
HDMI (default)/DP
1
9
(JP7) (JP14)
6
6
1
10
1
2
COM 2
1
2
COM 2
1
1
2
COM 3
COM 3
HDMI (default)/DP
Mic-in
USB 3-4 USB 3.0
1
(JP8) (JP15)
6
6
RESET-SW
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 1-2 USB 3.0
Line-out
HDD-LED
(JP9)
6
SPI Flash
BIOS
1
ECX
Clear CMOS
Data (JP1)
1
ECX
bettery
12
11
2
1
System
Fan 1
bettery
1
mSATA
ATX-SW
PWR-LED
Mini PCIe
LAN 2
DDR4_1 SODIMM
DDR4_2 SODIMM
10
9
Auto Power-on
Select (JP11) 1
DIO Power
DDR4_1 SODIMM
Mini PCIe
LAN 2
25
Front 1
Panel
10
9
DDR4_2 SODIMM
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
2
1
Auto Power-on
Select (JP11) 1
DIO Power
1
5
Reset
1
5
1
Reset
DIO
1
Status LED
HDD LED
26
Front Audio
Power
Button
2
1
S/PDIF 1
1
PCIe x4 (PCIE2)
-
HDD-LED - HDD LED
This LED will be lit when the hard drive is being accessed.
RESET SW - Reset Switch
This switch allows you to reboot without having to power off the system.
Audio
ATX-SW - ATX Power Switch
The mainboard is equipped with 2 audio jacks.
•
Line-out Jack
This jack is used to connect a headphone or external speakers.
•
Mic-in Jack
This jack is used to connect an external microphone.
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will be lit. When the system is in the S1 (Power On
Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To
RAM) state, it will blink every 4 seconds.
Pin Pin Assignment
Driver Installation
Install the audio driver. Refer to Chapter 8 for more information.
HDD-LED
RESET SW
3
HDD Power
5
Signal
7
Ground
9
RST Signal
11
N.C.
Pin Pin Assignment
2
LED Power
PWR-LED 4
LED Power
ATX-SW
6
Signal
8
Ground
10
Signal
27
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
S/PDIF Connector
LPC Connector
2
Parallel
2
10
26
S/PDIF 1
Power
Button
S/PDIF
DIO
1
Status LED
HDD LED
9
1
5
2
12
1
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
DIO
1
Status LED
HDD LED
DDR4_1 SODIMM
9
Parallel
2
1
5
2
12
1
25
Auto Power-on
Select (JP11) 1
DIO Power
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
DDR4_2 SODIMM
1
mSATA
1
mSATA
LAN 2
System
Fan 1
1
System
Fan 1
bettery
bettery
LAN 1
5
26
Front 1
Panel
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
Clear CMOS
Data (JP1)
LAN 1
1
Clear CMOS
Data (JP1)
1
1
1
10
Mini PCIe
LAN 2
Key Ground
SPDIF in
+5V
S/PDIF 1
Power
Button
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
Reset
SPDIF out
1
2
1
Front Audio
Front Audio
ECX
14
2
LPC
1
2
9
10
USB 3-4 USB 3.0
1
9
(JP7) (JP14)
6
6
2
1
1
(JP6) (JP13)
6
6
1
4
1
4
System
Fan 2
3
1
4
+
2
PCIe x16 (PCIE1)
1
JP3
J21
6
2
2 1
2 1
1
1
2
1
4
System
Fan 2
1
1
1
2
10
1
9
COM 1
1
2
9
3
VGA
J22
13
14
1
1
(JP5) (JP12)
6
6
4
SATA Power
16
6
JP2
9
10
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
1
+
6
4-pin power
1
1
2
LPC
1
9
(JP7) (JP14)
6
6
COM 1
1
1
10
COM 2
1
DVI
10
1
2
COM 3
SATA 0
1
1
2
SATA Power
LPC
1
1
1
(JP5) (JP12)
6
6
DVI
14
HDMI (default)/DP
2
1
1
1
(JP8) (JP15)
6
6
2
COM 2
SATA 3.0
SATA 1
SATA 0
1
1
10
COM 3
1
HDMI (default)/DP
DC-in
1
2
(JP9)
6
SPI Flash
BIOS
USB 1-2 USB 3.0
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 3-4 USB 3.0
ECX
(JP9)
6
SPI Flash
BIOS
1
1
DC-in
PCIe x4 (PCIE2)
4
4-pin power
1
2
PCIe x16 (PCIE1)
6
6
2 1
2 1
J21
6
2
16
JP3
JP2
1
VGA
J22
1
2
1
PCIe x4 (PCIE2)
-
-
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components within the system, which are typically provided by a Super I/O controller. Furthermore, it
can be used to interface firmware hubs, Trusted Platform Module (TPM) devices and embedded
controllers. Data transfer on the LPC bus is implemented over a 4 bit serialized data interface,
which uses a 24MHz LPC bus clock. For more information about LPC bus, please refer to the
Intel® Low Pin Count Interface Specification Revision 1.1’. The table below indicates the pin
functions of the LPC connector.
The S/PDIF connector is an audio interface for transmitting digital audio signals. The system
includes an S/PDIF header on the mainboard. Make sure pin 1 of the audio cable is aligned
with pin 1 of the S/PDIF connector.
Pin
1
3
5
7
9
11
13
Pin Assignment
L_CLK
L_RST#
L_FRAME#
L_AD3
L_AD2
INT_SERIRQ
5VSB
Pin
2
4
6
8
10
12
14
Pin Assignment
L_AD1
L_AD0
3V3
GND
Kev
GND
5V
28
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Expansion Slots
ECX Slot
2
10
1
9
Parallel
2
The ECX interface is used to install an ECX card for I/O expansion via a proprietary
daughter board.
26
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
1
5
2
12
1
Reset
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
System
Fan 1
Mini PCI Express
bettery
LAN 1
1
Clear CMOS
Data (JP1)
1
ECX
(JP9)
6
SPI Flash
BIOS
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
ECX
USB 3-4 USB 3.0
14
2
LPC
1
10
1
2
9
10
COM 2
1
1
9
(JP7) (JP14)
6
6
HDMI (default)/DP
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
1
1
1
(JP5) (JP12)
6
6
DVI
1
4
1
4
SATA Power
System
Fan 2
3
+
1
1
2
COM 3
2
PCIe x16 (PCIE1)
DC-in
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
6
6
2 1
2 1
J21
6
2
16
JP3
JP2
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
-
PCI Express x16
PCI Express x4
Mini PCIe Slot
The mainboard is equipped with a full-size Mini PCIe slot (PCIe/USB signals) and a half-size
Mini PCIe (mSATA/USB signals) slot. Supporting both USB and mSATA signals, the half-size
Mini PCIe slot can be used to expand the system’s storage capacity or provide mobile communication capability.
PCI Express x16 Slot/PCI Express x4 Connector
The system offers two types of riser cards. The EC510-SD is pre-installed with a riser card that
provides one PCI slot on the front panel. Whereas the EC511-SD is pre-installed with another
riser card that provides one PCIe x16 slot on the front panel.
Pin Assignment
GND
PCIE_ECX_RX1p
PCIE_ECX_RX1n
PCIE_ECX_TX1n
PCIE_ECX_TX1p
CLK_PCIE_ECX1_p
CLK_PCIE_ECX1_n
Reserved
Reserved
GND
CLK_PCIE_ECX3_p
CLK_PCIE_ECX3_n
GND
Reserved
DPB_AUX_n
DPB_AUX_p
Reserved
Reserved
Reserved
GND
DPB_LAN0_n
DPB_LAN0_p
DPB_LAN1_n
DPB_LAN1_p
DPB_LAN2_n
DPB_LAN2_p
DPC_AUX_n
DPC_AUX_p
DPB_HPD
GND
DPB_LAN3_n
DPB_LAN3_p
DPB_CTRL_CLK
DPB_CTRL_DATA
DPC_CTRL_CLK
DPC_CTRL_DATA
Reserved
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
Pin Assignment
GND
PCIE_ECX_RX2p
PCIE_ECX_RX2n
PCIE_ECX_TX2n
PCIE_ECX_TX2p
CLK_PCIE_ECX2_p
CLK_PCIE_ECX2_n
Reserved
Reserved
GND
PCIE_ECX_RX5p
PCIE_ECX_RX5n
PCIE_ECX_TX5n
PCIE_ECX_TX5p
CLK_PCIE_ECX5_p
CLK_PCIE_ECX5_n
Reserved
Reserved
HD_OUT
GND
PCIE_ECX_RX4p
PCIE_ECX_RX4n
PCIE_ECX_TX4n
PCIE_ECX_TX4p
CLK_PCIE_ECX4_p
CLK_PCIE_ECX4_n
Reserved
Reserved
Reserved
GND
LPC_FRAME#
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
LPC_LDRQ1#
DPC_HPD
29
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
12V DC-out
CLK_LPC
HD_SPKR
GND
USB3_RX0n
USB3_RX0p
GND
USB3_TX0n
USB3_TX0p
GND
HD_BITCLK
HD_SYNC
HD_SIN
GND
USB3_RX1n
USB3_RX1p
GND
USB3_TX1n
USB3_TX1p
GND
SATA_TXn
SATA_TXp
Reserved
GND
GND
DFI Board ID_0
DFI Board ID_1
DFI Board ID_2
SATA_RXn
SATA_RXp
VIN
+5VDU
+5VDU
GND
+3.3V
+3.3V
+3.3V
+3.3V
GND
+5V
+5V
+5V
+5V
+5V
2
10
1
9
Parallel
2
26
Front Audio
S/PDIF 1
Power
Button
DIO
1
Status LED
HDD LED
1
5
2
12
1
Reset
25
Front 1
Panel
Auto Power-on
Select (JP11) 1
DIO Power
10
9
5 2
USB 2.0 9 1
USB 2.0 13-14 1
DDR4_1 SODIMM
Mini PCIe
DDR4_2 SODIMM
1
mSATA
LAN 2
System
Fan 1
bettery
LAN 1
1
Clear CMOS
Data (JP1)
1
ECX
(JP9)
6
SPI Flash
BIOS
1
(JP8) (JP15)
6
6
USB 1-2 USB 3.0
USB 3-4 USB 3.0
14
2
LPC
2
2
1
1
(JP6) (JP13)
6
6
SATA 3.0
SATA 1
SATA 0
1
1
1
(JP5) (JP12)
6
6
DVI
12V2
1
GND1
1
1
4
System
Fan 2
DC-out
GND2
2
4
SATA Power
12V1
3
1
DC-in
9
10
1
9
(JP7) (JP14)
6
6
1
4
1
10
1
2
COM 2
1
HDMI (default)/DP
3
1
2
COM 3
6
2
PCIe x16 (PCIE1)
2
10
1
9
COM 1
4
4-pin power
1
1
1
1
JP3
JP2
J21
6
2
16
6
2 1
2 1
1
1
VGA
J22
2
1
PCIe x4 (PCIE2)
-
PLT-RST#
HD_RST#
GND
DPC_LAN0_n
DPC_LAN0_p
DPC_LAN1_n
DPC_LAN1_p
DPC_LAN2_n
DPC_LAN2_p
DPC_LAN3_n
DPC_LAN3_p
USB_PWR_SEL
GND
USB_1P
USB_1N
USB_0P
USB_0N
USB_OC#
PCIE_ECX_RX3p
PCIE_ECX_RX3n
PCIE_ECX_TX3n
PCIE_ECX_TX3p
GND
BID
SMB_CLK_RESUME
SMB_DATA_RESUME
INT_GPIO#
PCIe_Wake#
INT_SERIRQ
VIN
+3.3VDU
+3.3VDU
GND
+12V
+12V
+12V
+12V
GND
+5V
+5V
+5V
+5V
+5V
+
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
157
159
The 4-pin vertical type connector (optional) provides low power output.
30
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Digital I/O Connector (daughter board)
LAN Ports (daughter board)
G G 8 76 543 21
ACT/Link or
PoE LED
Speed LED
LAN 3~6 or PoE 1~4:
Intel I210IT
DIO
DIO
CN3
CN4
CN5
CN2
20
10
U15
U17
U14
U16
1
LAN4
G G 8 76 543 21
DIO
CN3
CN4
CN5
JP3
1
1
JP51
1
1
CN2
20
10
LAN3
LAN2
LAN1
3
3 JP1
3
3 JP4
3
JP2
U17
U15
U14
U16
1
LAN4
LAN3
LAN2
LAN1
DC_IN
JP3
1
1
JP51
1
1
3
3 JP1
3
3 JP4
3
4
3
2
1
CN7
JP2
DC_IN
4
3
2
1
CN7
Activity/Link LED
LED Behavior
Off
Blinking
On
The Digital I/O connector provides 16 digital inputs or outputs to enable monitor and control
of the state of the connected external devices. You can use the provided HW Utility to config­
ure a port to be either input or output. Please refer to Chapter 8 for more information.
Digital I/O Connector
Pins
DIO-A
DIO-B
1
DIO1
DIO1
PoE LED
LED Behavior
Off
DFI INC.
DFI INC.
SILK_TOP
MODEL:
XCT3-4LPSEGD
DATE:
08/22/2017
REV:
A
SILK_TOP
MODEL:
XCT3-4LPSEGD
DATE:
08/22/2017
REV:
A
Description
No link
Data Activity
Link
Speed LED
LED Behavior
Off
Green
Orange
Speed LED
Description
LED Behavior
The system is not
Off
powered on.
Supplying power over Green
the Ethernet link
Orange
Description
10Mbps connection
100Mbps connection
1Gbps connection
Description
10Mbps connection
2
DIO2
DIO2
3
DIO3
DIO3
4
DIO4
DIO4
5
DIO5
DIO5
6
DIO6
DIO6
7
DIO7
DIO7
LAN3 to LAN6 can be normal Gigabit ports or PoE (Power over Ethernet) ports. With PoE
(Power over Ethernet) support, the ports carry power to connected devices without the need
for individual power supplies. Each port delivers up to 15.4 Watts of power to the connected
devices that comply with IEEE 802.3af, for example, access points and VoIP phones.
8
DIO8
DIO8
Driver Installation
G
GND
GND
Install the LAN driver. Refer to Chapter 8 for more information.
G
GND
GND
Green
100Mbps connection
1Gbps connection
31
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 6
Chapter 6 - Mounting Options
2. Use the provided mounting screws to secure the wall mount brackets on each side of the
system unit.
Wall Mount
The wall mount kit includes the following:
•
•
2 Wall mount brackets
4 Bracket screws
Mounting screw
Wall mount
bracket
Wall mount
bracket
Mounting screw
The following illustration shows the location and dimension of the holes for mounting the device
onto a wall or rack .
1. The wall mounting holes are located on the bottom of the system unit.
Mounting hole
Ø8.50
80
120
16
5
6
Ø3.60
4
251.80
262.80
Mounting hole
32
Chapter 6 Mounting Options
www.dfi.com
Chapter 7
Chapter 7 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
KEYs
Function
Right and Left Arrows
Moves the highlight left or right to select a
menu.
Up and Down Arrows
Moves the highlight up or down between
submenus or fields.
<Esc>
Exits to the BIOS setup utility
<F1>
Displays general help
<F5/F6>
Changes the highlighted value
<F9>
Changes to the default setup
<F10>
Saves and exits the setup program.
<Enter>
Press <Enter> to enter the highlighted
submenu
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Entering the BIOS Setup Utility
Scroll Bar
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
33
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1980 to 2099.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
34
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
ACPI Settings
CPU Configuration
This section configures the ACPI settings.
This section configures the CPU.
Wake on LAN
Intel® SpeedStep™
Enable the system to be waken up via the onboard LAN.
Enable or disable the Enhanced Intel SpeedStep® Technology (EIST). The EIST helps
optimize the balance between system’s power consumption and performance.
State After G3
Turbo Mode
Specify which state the system should be in when the power is re-applied after a power
failure (G3 state, the mechanical-off state).
S0 State
Power on the system when power is re-applied after a AC power loss.
S5 State
The system appears to be off when power is re-applied after AC power loss.
Enable or disable processor turbo mode (requires that EMTTM is enabled too), which
allows the processor core to automatically run faster than the base frequency when
the processor’s power, temperature, and specification are within the limits of TDP.
Wake on RTC
Automatically power the system on at a particular time every day from the Real-time clock
battery. Specify the wake up time of the day below: <hour> (00~23), <minute> (00~59),
<second> (00~59).
35
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Video Configuration
This section configures the video settings. Note that the options may vary according to the
"Boot type" selected in the "Boot" menu.
Primary Display
Select the primary internal graphics.
Boot display
Set the display device combination during system booting. Note that this option only
appears when the boot type selected is dual or legacy boot type.
Internal Graphics
Enable, disable or to automatically detect internal graphics.
Always Enabled PEG
Enable or disable the PCIe graphics function.
36
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Audio Configuration
SATA Configuration
This section configures the audio settings.
This section configures the SATA controllers.
HD Audio
SATA Controller(s)
Control the detection of high-definition audio devices.
Enable or disable Serial ATA devices.
Disabled
SATA Mode Selection
The high-definition audio will be unconditionally disabled.
The mode selection configures the SATA controller(s).
Enabled
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
The high-definition audio will be unconditionally enabled.
RAID Mode
This option allows you to create RAID using Intel® Rapid Storage Technology (Intel® RST)
on Serial ATA devices.
Auto
The high-definition audio will be enabled if present and disabled otherwise.
Serial ATA Port 0, 1 and 2
Enable or
SATA Port
SATA Port
SATA Port
disable each serial ATA port:
0 controls SATA3_0
1 controls SATA3_1
2 controls the half-size Mini PCIe slot
37
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
USB Configuration
PCI Express Configuration
This section configures the parameters of the USB devices.
This section configures the settings of PCI Express Root Ports.
USB BIOS Support
Disabled
Disable the USB keyboard/mouse/storage support.
Enabled
Enable the USB keyboard/mouse/storage support.
UEFI Only
Enable the USB keyboard/mouse/storage support only under UEFI environment.
PCI Express Root Port
Enable or disable each PCI Express Root Port:
PCIe Root Port 3 controls PCIE1 (x16) connector
PCIe Root Port 4 controls LAN 1
PCIe Root Port 6 controls LAN 2
PCIe Root Port 7 controls the full-size Mini PCIe slot
PCIe Root Port 8 controls PCIE2 (x4) connector
PCIe Speed
Select the speed of the PCI Express Root Port: Auto, Gen1, Gen2 or Gen3.
38
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
ME Configuration
Active Management Technology Support
This section configures flashing of Intel® Active Management Engine region.
The section allows users to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Please refer to Chapter 10 - Intel AMT Settings for more information.
Me Fw Image Re-Flash
Intel AMT Support
Enable or disable flashing of the Intel ME region.
Enable or disable Intel® Active Management Technology BIOS extension.
®
Un-Configure ME
Clears all ME related configurations without requiring a password on the next boot.
39
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Super IO
COM Port Configuration
This section configures the system’s super I/O chip parameters.
This section configures serial port settings.
Smart Fan Function
This section configures the Smart Fan Function.
COM Port 1 to COM Port 3
Configure the settings of each serial port.
Disable Disable the serial port.
Enable
SYS Smart Fan/CPU Smart Fan/SYS Smart Fan2 Control
Enable the serial port.
RS485 Auto Flow
Enable or disable the smart fan.
Disable Disable the RS485 auto flow mechanism.
Boundary 1 to Boundary 4
Enable
Enable the RS485 auto flow mechanism.
Set the boundary temperatures that determine the operation of the fan with different
fan speeds accordingly. For example, when the system or the CPU temperature reaches
boundary temperature 1, the system or CPU fan should be turned on and operate at
the designated speed.
The range of the temperature is from 0 to 127oC.
Fan Speed Count 1 to Fan Speed Count 4
Set the fan speed. The range is from 0 (fan stop)-100% (full speed).
40
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
LPT Port 1
PC Health Status
Enable, disable or automatically detect the parallel port on the board.
This screen displays PC health information.
WDT
Enable or disable the watchdog function.
AC Power Loss
Set the AC power loss to Always off or Always on. When it is set to Always off, the
system’s status will be power-off after an AC power loss event. When it is set to Always on, the system’s status will be power-on after an AC power loss event.
41
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Security
Power on Password
This section configures the trusted platform module (TPM) and storage security.
Select "enabled" to require users to input the supervisor password when the system is entering the POST (power-on self-test).
Set All HDD Password
Set password for all HDDs. The length of the password must be greater than one character
and less than or equal to 32 characters.
Set All Master HDD Password
Set the master password for all HDDs.The length of the password must be greater than one
character and less than or equal to 32 characters.
To set password for each storage device, use the "Storage Password Setup Page" option.
TPM Availability
Show or hide the TPM availability and its configurations.
TPM Operation
Enable or disable the TPM function. It displays the following options:
•
No Operation: No changes to current state.
•
Disable: Disable and deactivate TPM.
•
Enable: Enable and activate TPM.
Clear TPM
Remove all TPM ownership contents.
Set Supervisor Password
Set the administrative password. The length of the password must be greater than
one character and less than or equal to 10 characters. Depending on the state of
power-on password selected, the supervisor password may be required during POST or
when entering the BIOS setup utility.
42
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Storage Password Setup Page
Boot
Enhance the HDD security for each HDD device by using a password.
This section configures boot options.
Numlock
Set Storage Password
Select the power-on state for the numlock key.
Set all HDD password. The length of the password must be greater than one character
and less than or equal to 32 characters.
Boot Type
Select the boot type. The options include Dual Boot Type, Legacy Boot Type, and UEFI
Boot Type.
Set Master HDD Password
Set the master password for all HDDs. The length of the password must be greater
than one character and less than or equal to 32 characters. When the security mode
is set to Lock, input the master HDD password to unlock the HDD. Clear the HDD
password by pressing “Enter” to set HDD security to be disabled and set a new master
HDD password.
Network stack
Enable or disable UEFI network stack. This option is only available if the boot type is set to be
UEFI or Dual. It supports the operation of these functions or software: Windows 8 BitLocker
Network Unlock, UEFI IPv4/IPv6 PXE and legacy PXE Option ROM.
PXE Boot to LAN or PXE Boot Capability
Enable or disable PXE (Preboot eXecution Environment).
USB Boot
Enable or disable boot to USB boot devices.
Note:
If the boot type is set to UEFI, the method for RAID volume creation will be
different. Please refer to Chapter 9 ̵- RAID for more information.
43
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Legacy
Boot Type Order
This section configures legacy boot order.
Use + and - keys to arrange the sequence of storage devices that the system’s hardware will check in the operating system’s boot files. The first device in the order list
has the highest boot priority.
Hard Disk Drive
All installed hard disk drives will be displayed in this field. Use + and - keys to arrange
the sequence of hard disk drives that the system’s hardware will check in the operating system’s boot files.
Normal/Advanced Boot Menu
Normal
Select the boot menu type: normal or advanced.
For the advanced menu type: Use + and - keys to arrange the priority of the detected
boot devices.
For normal menu type: Select the "Boot Type Order", "Hard Disk Drive" or USB category to view and arrange the order of the listed devices.
44
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Exit
This section configures the parameters for exiting the BIOS menu.
Exit Saving Changes
Select this field and then press <Enter> to exit the BIOS setup and save your changes.
Load Optimal Defaults
Select this field and then press <Enter> to load optimal defaults.
Discard Changes
Select this field and then press <Enter> to exit the BIOS setup without saving your changes.
45
Chapter 4 BIOS Setup
www.dfi.com
Chapter 7
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions on how to update
BIOS with the flash utility.
1. The Intel® Management Engine has already been integrated into the system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing BIOS updating procedure. For your convenience, we
will also provide you with an auto-execution file in the downloaded BIOS file. This auto-execution file will bring you directly to the flash utility menu soon after system boots up and finishes
running the boot files in your boot disk.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
RRead file successfully.
3. If you do not follow the methods above, the Intel® Management Engine will not be
updated and will cease to be effective.
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
(path= “platform.ini”)
Information
Please do not remove the AC power
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: SD263
New BIOS Model name: SD263
Current BIOS version: 65.05A
New BIOS version: 65.05A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\SD263>_
100%
100%
46
Chapter 4 BIOS Setup
www.dfi.com
Chapter 8
Chapter 8 - Supported Software
For Windows 8.1
The DVD that came with the system board contains drivers, utilities and software applications
required to enhance the performance of the system board.
Insert the DVD into a DVD-ROM drive. The auto-run screen will appear. If the “Autorun” does
not automatically start, please go directly to the root directory of the DVD and double-click
“Setup”.
For Windows 10
47
Chapter 8 Supported Software
www.dfi.com
Chapter 8
For Windows 7
Intel Chipset Software Installation Utility
The Intel Chipset Software Installation Utility is used for updating Windows® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Software Installation Utility” on the main menu.
1. Setup is ready to install
the utility. Click “Next” to
continue.
2. Read the license agreement
and then click “Yes”.
48
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Graphics Drivers
3. Go through the readme document for more installation tips
and then click “Next”.
To install the driver, click “Intel Graphics Drivers” on the main menu.
1. Setup is now ready to install
the graphics driver. Click
“Next” to continue.
4. Click “Finish” to exit setup.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop
theme” is enabled. With this enabled, after the graphics driver is installed and the
system is rebooted, the screen will turn blank for 1 to 2 minutes (while WinSAT is
running) before the Windows 7/Windows 8.1/Windows 10 desktop appears. The
“blank screen” period is the time Windows is testing the graphics performance.
2. Read the license agreement
and then click “Yes”.
49
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Audio Drivers
3. Go through the readme
document for system requirements and installation
tips and then click “Next”.
To install the driver, click “Audio Drivers” on the main menu.
1. Setup is ready to install
the driver. Click “Next” to
continue.
4. Setup is now installing
the driver. Click “Next” to
continue.
2. Click “Yes, I want to restart
my computer now” and
then click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
5. Click “Yes, I want to restart
this computer now” and
then click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
50
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel LAN Drivers
4. Click “Install” to begin the
installation.
To install the driver, click “Intel LAN Drivers” on the main menu.
1. Setup is ready to install
the driver. Click “Next” to
continue.
5. After the installation is
complete, click “Finish” to
exit setup.
2. Read and License Agreement and click “I accept
the terms in the license
agreement” if you agree
the terms in the agreement, and then click “Next”.
3. Select the program features
you want to install and
then click “Next”.
51
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Kernel Mode Driver (For Windows 7 only)
3. Click “Restart Now” to
restart your computer when
the installation is complete.
To install the driver, click “Kernel Mode Driver Framework” on the main menu.
1. Click “Yes“ to install the
update.
2. The update is being installed now.
52
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Management Engine Drivers
3. Setup is currently installing
the driver. After the installation is complete, click
“Next”.
To install the driver, click “Intel Management Engine Drivers” on the main menu.
1. Setup is ready to install
the driver. Click “Next” to
continue.
4. Please wait while the product is being installed.
2. Read and License Agreement and click “I accept
the terms in the license
agreement” if you agree
with the terms in the
agreement, and then click
“Next”.
5. After the installation is
complete, click “Finish” to
exit setup.
53
Chapter 8 Supported Software
www.dfi.com
Chapter 8
HW Utility
3. Read the license agreement and
then click “I accept the terms in
the agreement” if you accept the
terms in the agreement. Click
“Next” to continue.
HW Utility provides information about the board and enables you to configure Watchdog and
DIO functions. To access the utility, click “HW Utility” on the main menu.
Note:
If you are using Windows 7 or later versions, you need to access the operating system as an administrator to be able to install the utility.
1. Setup is ready to install the
driver.
4. The wizard is ready to start
the installation. Click “Install”.
2. Click “Next” to continue.
5. Please wait while the program
features are being installed.
54
Chapter 8 Supported Software
www.dfi.com
Chapter 8
6. After the installation is complete, click “Finish” to exit
setup.
HW Health
HW Health Set
The HW Utility icon will appear on the desktop. Double-click the icon to open the utility.
Watchdog
DIO
Note:
The screenshot displayed above is for illustrative purpose only, and may not
resemble the actual screen.
The EC510/511-SD Utility features the following tabs: Information, HW Health, HW Healthset,
Watchdog, and DIO. Click on the tabs to access each function.
55
Chapter 8 Supported Software
www.dfi.com
Chapter 8
USB 3.0 Driver (For Windows 7 and Windows 8.1)
3. Go through the readme document for more installation tips
and then click “Next”.
To install the driver, click “USB 3.0 Driver” and “USB 3.0 Host Drivers (Ext. I/O board) ” on the
main menu.
1. Setup is ready to install the driver.
Click “Next” to continue.
4. Setup is currently installing the
driver. After the installation is
complete, click “Next”.
2. Read the license agreement and
then click “Yes” if you agree with
the terms in the agreement.
5. After the installation is complete,
click “Finish”.
56
Chapter 8 Supported Software
www.dfi.com
Chapter 8
IO Driver (For Windows 7-64 bit, 8.1 and 10)
3. Read the file information and
then click “Next”.
To install the driver, click “IO Driver” on the main menu
1. Setup is ready to install the driver.
Click “Next” to continue.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
2. Read the license agreement carefully.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement and then
click “Next”.
57
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Microsoft Framework 4.5.2 (For Windows 7)
5. Setup is now installing the
driver.
Note:
Before installing Microsoft Framework 4.5.2, make sure you have updated your
Windows 7 operating system to Service Pack 3.
To install the driver, click “Microsoft Framework 4.5.2” on the main menu.
1. Setup is now extracting files.
6. Click “Finish” to exit setup.
2. Read the license agreement carefully.
Click “I have read and accept
the terms of the License Agree
ment” if you agree with the terms
in the agreement and then click
“Next”.
58
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Rapid Storage Technology
3. Setup is now installing the
driver.
The Intel Rapid Storage Technology is a utility that allows you to monitor the current status of
the SATA drives. It also enables enhanced performance and power management for the storage subsystem.
To install the driver, click “Intel Rapid Storage Driver” on the main menu.
1. The setup program is preparing
to install the driver. Please exit
all programs before continuing
with the installation.
4. Click “Finish” to exit setup.
2. Read the license agreement
carefully, accept the terms of the
License Agreement, then click
“Next” to continue.
59
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Infineon TPM Driver and Tool (optional)
3. Read the readme information and
then click “Next.”
To install the driver, click “Infineon TPM driver and tool (option)” on the main menu.
1. The setup program is preparing
to install the driver.
4. Setup is currently installing the
driver. Click “Next” to install to
the default folder or select to
change the installation folder.
The setup will then inform you
that the Intel® Rapid Storage
Technology will be installed on
your system.
2. The setup program is now ready
to install the utility. Click “Next”
to continue.
5. Click “Yes, I want to restart
this computer now”, then
click “Finish.”
3. Click “I accept the terms in the
license agreement” if agree with
the terms in the agreement and
then click “Next”.
Restarting the system wil
allow the new software
installation to take effect.
60
Chapter 8 Supported Software
www.dfi.com
Chapter 8
4. Enter the necessary information
and then click “Next”.
7. TPM requires installing the Microsoft Visual C++ package prior to
installing the utility. Click “Install”.
5. Select the setup type and then
click “Next”.
8. The setup program is currently
installing the Microsoft Visual
C++ package.
9. Click “Finish” to exit setup.
6. Click “Install” to start the installation.
61
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Adobe Acrobat Reader 9.3
10. Click “Yes“ to restart your system.
To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.
1. Click Next to install or click
Change Destination Folder
to select another folder.
2. Click “Install” to begin installation.
3. Click “Finish” to exit setup.
62
Chapter 8 Supported Software
www.dfi.com
Chapter
Chapter 95
Chapter 9 - RAID
Settings
The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1,
and RAID 5.
To enable the RAID function, the following settings are required.
1. Connect the Serial ATA drives.
RAID Levels
2. Enable Serial ATA in the Insyde BIOS.
RAID 0 (Striped Disk Array without Fault Tolerance)
3. Create a RAID volume.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk
drives. This improves the I/O performance of the drives at different channel; however it is not
fault tolerant. A failed disk will result in data loss in the disk array.
3-1. Create a RAID volume if the boot type is UEFI.
RAID 1 (Mirrored Disk Array with Fault Tolerance)
Refer to Chapter 3 for details on connecting the Serial ATA drives.
4. Install the Intel Rapid Storage Technology Utility.
Step 1: Connect the Serial ATA Drives
RAID 1 copies and maintains an identical image of the data from one drive to the other drive.
If a drive fails to function, the disk array management software directs all applications to the
other drive since it contains a complete copy of the drive’s data. This enhances data protection
and increases fault tolerance to the entire system. Use two new drives or an existing drive and
a new drive but the size of the new drive must be the same or larger than the existing drive.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID BIOS utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
RAID 5 (Striped Disk Array with Distributed Parity)
RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides
better hard drive performance and higher disk utilization than RAID 1.
Step 2: Enable RAID in the Insyde BIOS
1. Power-on the system then press <Del> to enter the main menu of the BIOS setup utility.
RAID Level
Min. Drives
Protection
Description
RAID 0
2
None
Data striping without redundancy
3. Change the “SATA Mode Selection” to “RAID” mode.
RAID 1
2
Single Drive Failure
Disk mirroring
4. Save the changes in the “Save & Exit” menu.
Single Drive Failure
Block-level data striping with
distributed parity
5. Reboot the system.
Chapter
RAID
5 5 RAID
3
2. Go to “Advanced” menu, and select the “SATA Configuration” menu.
63
Chapter 9 RAID
www.dfi.com
Chapter
Chapter 95
Step 3: Create a RAID Volume
Step 3-1: Create a RAID Volume if the Boot Type is UEFI
1. When the Intel® RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
If the boot type is set to UEFI, RAID volume creation will be different. Please use the following
steps to create RAID volumes. To set the boot type, enter the Insyde BIOS and go to “Boot”
>”Boot type”.
2. Select 1: Create RAID Volume and press <Enter>.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
1. Go to the “Advanced” menu of the Insyde BIOS.
4. Use the up or down arrow keys to select the strip size and press <Enter>.
2. The “Intel® Rapid Storage Technology” menu appears. Enter this menu.
5. Press <Enter> to select the physical disks.
6. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
7. Press <Enter>.
8. Select the volume size and press <Enter>. You must select less than one hundred percent
of the available volume space to leave space for the second volume.
9. Press <Enter> to create the volume.
10. At the prompt, press <Y> to confirm volume creation.
11. Select 4: Exit and press <Enter>.
12. Press <Y> to confirm exit.
Note:
These steps are cited from the Intel® Support site, “Set Up a System with Intel®
Matrix RAID Technology” (Article ID: 000005789).
http://www.intel.com/content/www/us/en/support/boards-and-kits/000005789.html
3. The screen displays all available drives. Select “Create RAID volume” to create a RAID
volume”.
Chapter 5 RAID
4. Use the up or down arrow keys to select the RAID level and press <Enter>.
5. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
6. Press <Enter>.
7. Use the up or down arrow keys to select the strip size and press <Enter>.
8. Enter the volume size and press <Enter>.
9. At the prompt, press <Y> to confirm volume creation.
64
Chapter 9 RAID
www.dfi.com
Chapter
Chapter 95
Step 4: Install the Intel Rapid Storage Technology Utility
5. Go through the readme
document to view system
requirements and installation information then click
Next.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/
or SATA drives. It enables enhanced performance and power management for the storage
subsystem.
1. Insert the provided DVD into an optical drive.
2. Click “Intel Rapid Storage Technology Utility” on the main menu.
3. Setup is ready to install
the utility. Click Next.
6. Click Next to install to
the default folder or click
change to choose another
destination folder.
4. Read the license agreement and click “I accept
the terms in the License
Agreement.“ Then, click
Next.
Chapter 5 RAID
7. Confirm the installation and
click Next.
65
Chapter 9 RAID
www.dfi.com
Chapter
Chapter 95
8. Click “Yes, I want to restart
this computer now” to
complete the installation
and then click Finish.
Chapter 5 RAID
66
Chapter 9 RAID
www.dfi.com
Chapter 10
6
Chapter
Chapter 10 - Intel AMT Settings
Enable Intel® AMT in the BIOS
Overview
1. Power on the system then press <Del> to enter the main menu of the BIOS setup utility.
Intel Active Management Technology (Intel AMT) combines hardware and software solutions
to provide maximum system defense and protection to networked systems.
2. In the “Advanced” menu, select “Active Management Technology Support”.
®
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and the latest security applications, Intel® AMT provides the following functions:
•
Discover
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
•
Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
•
Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
3. In the “Active Management Technology Support” menu, select “Enabled” for “Intel AMT
Support”.
67
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
Set up Intel® AMT using the Intel® Management
4. In the “Exit” menu, select “Exit Saving Changes” and then select “Yes”.
Engine BIOS Extension (MEBX)
1. After the system reboots, press <Del> to enter the BIOS menu again.
2. In the “Advanced” menu, select “MEBX Configuration” to enter the Manageability Engine
BIOS Extension (MEBx) Setup.
3. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password,
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
68
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
4. Enter a password in the space provided under “Intel(R) ME Password” and then press
“Enter”. The password must include:
•
•
•
•
•
5. You will be asked to verify the password. Enter the same new password in the space provided under “Verify Password” and then press “Enter”.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Enter] = Select Entry
[Esc]= Exit
6. Select “Intel(R) ME General Settings” and then press “Enter”.
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
69
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
7. Select “Change Intel(R) ME Password” and then press “Enter”.
8.Select “Local FW Update” and then press “Enter”. Select “Enabled” or “Disabled” or
“Password Protected” and then press “Enter”.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under “Intel(R) ME New Password” and then press “Enter”.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
Disabled
Enabled
Password Protected
<Enabled>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9. Select Previous Menu until you return to the “Main Menu”. Select “Intel(R) AMT Configuration” and then press “Enter”.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
[Esc]= Exit
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
70
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
10. In the “Intel(R) AMT Configuration” menu, select “Manageability Feature Selection” and
then press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
12. In the “SOL/Storage Redirection/KVM” menu, select “Username and Password” and then
press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved..
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
11. In the “Intel(R) AMT Configuration” menu, select “SOL/Storage Redirection/KVM” and
then press “Enter”.
13. In the “SOL/Storage Redirection/KVM” menu, select “SOL” and then press “Enter”. Select
“Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
sion>
> Remote Setup And Configuration
> Power Control
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
< Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Anytime>
<Full Unprovi-
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
71
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
14. In the “SOL/Storage Redirection/KVM” menu, select “Storage Redirection” and then press
“Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
16. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“User Consent” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
User Opt-in
Opt-in Configurable from Remote IT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< KVM>
< Enabled>
Disabled
Enabled
Configure When User Consent Should be Required.
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
15. In the “SOL/IDER/KVM” menu, select “KVM Feature Selection” and then press “Enter”.
Select “Enabled” or “Disabled” and then press “Enter”.
[Esc]= Exit
17. In the “User Consent” menu, select “User Opt-in” and then press “Enter”. Select “None”
or “KVM” or “ALL” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
72
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
20. In the “Intel(R) AMT Configuration” menu, select “Network Setup” and then press “Enter”.
18. In the “User Consent” menu, select “Opt-in Configurable from Remote IT” and then press
“Enter”. Select “Enabled” or “Disable Remote Control of KVM Opt-in Policy” and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< ALL>
< Enabled>
Disabled
Enabled
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
21. In the “Intel(R) ME Network Setup” menu, select “Intel(R) ME Network Name Settings”
and then press “Enter”.
19. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“Password Policy” and then press “Enter”.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Intel (R) ME Network Name Settings
> TCP/ IP Settings
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Stepup And Configuration
Anytime
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Enter] = Select Entry
[Esc]= Exit
73
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
22. In the “Intel(R) ME Network Name Settings” menu, select “Host Name” and then press
“Enter”. Enter the computer’s host name and then press “Enter”.
24. Select “Shared/Dedicated FQDN” and then press “Enter”. Select “Shared” or “Dedicated”
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Host Name
[Enter] = Complete Entry
Dedicated
Shared
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc]= Discard Changes
23. Select “Domain Name” and then press “Enter”. Enter the computer’s domain name and
then press “Enter”.
25. Select “Dynamic DNS Update” and then press “Enter”. Select “Enabled” or “Disabled” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Domain Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
_
_
<Shared>
<Disabled>
Disabled
Enabled
[Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
74
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
26. Select Previous Menu until you return to the “Intel(R) ME Network Setup” menu. Select
“TCP/IP Settings” and then press “Enter”.
28. In the “Intel(R) AMT Configuration” menu, select “Activate Network Access” and then
select “Yes/No” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
TCP/ IP SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Wired LAN IPV4 Configuration
[↑↓] = Move Highlight
[Enter] = Select Entry
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Activates the current network settings
and opens the ME network interface
Continue: (Y/N)
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
[Esc]= Exit
27. In the “TCP/IP Settings” menu, select “Wired LAN IPV4 Configuration” and then press
“Enter”.
29. In the “Intel(R) AMT Configuration” menu, select “Unconfigure Network Access” and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
<Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
Disabled
Enabled
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<During Setup And
Configuration>
<Full Unprovision>
Full Unprovision
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
75
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
30. In the “Intel(R) AMT Configuration” menu, select “Remote Setup And Configuration” and
then press “Enter”.
32. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning Record” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
< Enabled>
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
<Anytime>
<Full Unprovision>
Provision Record is not present
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
31. In the “Intel(R) Remote Setup And Configuration” menu, select “Current Provisioning
Mode” and then press “Enter”.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
[Enter] = Select Entry
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Provisioning Mode: PKI
[↑↓] = Move Highlight
[Enter] = Select Entry
33. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server IPV4/
IPV6”, enter “Provisioning server address” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Provisioning server address
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
76
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
34. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server
FQDN”, enter the FQDN of Provisioning server, and then press “Enter”.
36. In the “Intel(R) Remote Setup And Configuration” menu, select “TLS PKI” and then press
“Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
35. In the “Intel(R) Remote Setup And Configuration” menu, select “RCFG” and press “Enter”,
and then select “Start Configuration Y/N” and press “enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
This will activate Remote Condiguration. Continue: (Y/N)
[Enter] = Select Entry
[Esc]= Exit
37. In the “Intel(R) Remote Configuration” menu, select “Remote Configuration**” and press
“Enter”, and then select “Enabled” or “Disabled” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
[↑↓] = Move Highlight
[Enter] = Select Entry
< Enabled>
_
Disabled
Enabled
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
77
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
40. In the “Intel(R) AMT Configuration” menu, select Power Control, and then press “Enter”.
38. Select “PKI DNS Suffix”, enter the “PKI DNS Suffix”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Hash Name
VeriSign Class 3
VeriSign Class 3
Go Daddy Class 2
Comodo AAA CA
Starfield Class 2
VeriSign Class 3
VeriSign Class 3
VeriSign Class 3
GTE CyberTrust G1
Baltimore Cyber Tr
Cyber Trust Global
Verizon Global Ro
Entrust. net CA (2
Entrust Root CA
VeriSign Universa
Go Daddy Root CA
Entrust Root CA Startfield Root CA
< Enabled>
_
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[Ins]= Add New Hash
[↑↓] =Move Highlight
39. Select “Manage Hashes” and press “Enter”, and then select one of the hash names.
INTEL (R) REMOTE CONFIGURATION
[↑↓] = Move Highlight
Algorithm
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
[+] = Activate Hash
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
< Enabled>
_
[Enter] = Select Entry
[Delete] = Delete Hash
[Enter] = View Hash
Default
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
41. In the “Intel(R) AMT Power Control” menu, select “Intel(R) AMT ON in Host Sleep States”
and then press “Enter”. Select an option and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Active
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<Anytime>
<Full Unprovision>
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
78
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
44. Select Previous Menu until you return to the “Main Menu”. Select “Exit” and then press
“Enter”. Type “Y” and then press “Enter”.
42. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout” and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
These configurations are effective only after AMT provisioning has started
Intel (R) AMT ON in Host Sleep States
<Desktop: ON in S0,
ME Wake in S3, S4-5>
Idle Timeout
65535
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Desktop : ON in S0
Desktop : ON in S0, ME Wake in S3, S4-5
Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
43. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout” and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
<ENTER> = Complete Entry
[ESC]= Discard Changes
79
Chapter 10 Intel AMT Settings
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising