DFI | VC230-BT Installation Guide | manual | Dfi VC230-BT Installation Guide Manual

Dfi VC230-BT Installation Guide Manual
VC230-BT Installation Guide
Package Contents
• 1 VC230-BT system unit
• 6 Mounting screws for Mini PCIe module
• 1 Quick Installation Guide
• 1 Disk includes:
- Drivers / Manual
Note:
The CD that came with the system contains an autorun screen to install drivers, utilities,
and software applications required to enhance the performance of the system and a user's
manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will
appear. If after inserting the CD, “Autorun” did not automatically start, please go directly to
the root directory of the CD and double-click “Setup”. Please install all required drivers.
DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
www.dfi.com
1
Panel
USB 3.0
Status LED (Blue)
COM 4/ 8-bit DIO
CANbus*
COM 2
(RS232/RS422/RS485)
Power button
(Green LED) HDMI
Front View
Reset
Antenna
hole
Antenna
VCC/ACC/GND
hole
(Connects to car battery)
COM 3
(RS232/RS422/RS485)
LAN 1 LAN 2
Antenna
hole
VGA
Rear View
USB 2.0
Note:
You can choose to wire the COM 4 port to be a CANbus (Controller Area Network)
interface instead.
2
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open the system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 4 mounting screws on the bottom side of the system are used to secure
the cover to the chassis. Remove these screws and then put them in a safe
place for later use.
Chassis screw
4. After removing the mounting screws, lift the bottom side of the chassis cover
to open the system. To access the Mini PCIe and the micro SD slots, revmoe the
four screws to uninstall the power board.
Mounting screw
Mounting screw
3
Installing a Mini PCIe Card
The system board is equipped with 3 Mini PCIe slots: two full-size and one halfsize slots. Here we will demonstrate the installation of a full-size Mini PCIe card
(mSATA interface) for capacity expansion.
1. Grasp the Mini PCIe card by its edges and align the notch in the connector of
the PCIe card with the notch in the connector on the system board.
2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on the system board.
Mounting screw
Note:
The system also has one additional full-size Mini PCIe and one half-size Mini PCIe slot
that use PCIe (PCIe/USB/3G/GPRS/CANbus signals) and LPC (PCIe/USB/LPC signals)
interface respectively.
4
Board Layout and Jumper Settings
COM 3
JP22
1
1
3
10
12
10
12
1
1
(JP20)
(JP18)
1
(JP17)
3
DDR3L
DDR3L
DDR3L
(JP22, JP21)
(JP18)
(JP20)
(JP17)
DDR3L
1
Battery
COM 4/DIO Select
Digital I/O 4-7 Output State
Digital I/O 0-3 Output State
Digital I/O Power Select
(JP21)
DDR3L
DDR3L
DDR3L
DDR3L
DDR3L
Chassis
Intrusion
1
SPI
Flash
BIOS
COM 4
Buzzer
Intel Atom
1
Clear CMOS
Data (JP24)
COM 2
Standby
Power LED
E3800 Series
VGA/DVI-I
SATA 2.0
ASMedia
ASM1442
SATA 1
1
4
1
SATA
Power 1
eMMC
(optional)
4
Mini PCIe
mSATA
Mic-in
Nuvoton
NCT6106D
1
USB 2.0
USB 1
iTE
IT8528E
USB 2
MicroSD
(optional)
USB 6
USB 0
USB 3.0
COM 6
2
10
USB 0 System Fan
Power
1
Select
(JP5)
9
1
1
1
(JP25)
10
5
1 1
(JP2)
(JP23)
1
(JP3)
6
2 1
3
(JP4)
1
Intel
WGI210AT
USB 5-7 Power
Select (JP7)
9
COM 5
USB 1-2
Power Select (JP6)
1
Intel
WGI210AT
SMSC
USB4604
USB 7
1
2
10
1
9
USB 5
LAN 1
USB 2.0
SIM Card
HDMI
Reset
Auto Power-on Select
LCD/Inverter Power Select
Backlight Enable Power Select
Dimming Mode Select
Panel Power Select
(JP25)
(JP2)
(JP3)
(JP4)
(JP23)
NXP
PTN3460
LAN 2
DC-in
Power
Mini PCIe
BOTTOM
TOP
USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7)
Auto Power-on Select
JP25
+5V_standby (default)
1-2 On
Power-on via power button
1-2 On
+5V
2-3 On
Power-on via AC power (default)
2-3 On
JP24
Digital I/O Power Select
JP17
Normal (default)
1-2 On
+5V_standby
1-2 On
Clear CMOS Data
2-3 On
+5V (default)
2-3 On
Clear CMOS Data
Digital I/O Output State
COM 4/DIO Select
JP18 (DIO 4-7)
JP20 (DIO 0-3)
GND (default)
1-2 On
+5V or +5V_standby
2-3 On
JP21, JP22
COM 4 (default)
1-2, 4-5
7-8, 10-11 On
DIO
2-3, 5-6
8-9, 11-12 On
Note:
You cannot use COM 4 and DIO at the same time.
Please adjust JP21 and JP22 together.
www.dfi.com
5
Delay Turn-on/off Switch
The DIP switch (SW1) on the power board can be used to trun on or off the system at a specific on/off delay time via car ignition.
SW1-2: System-on delay enable/disable
On (Default)
Enable (delay time setting adjustable by SW1-4 and 1-5 as shown in
the table below)
Off
Disable (System-on delay = 3 sec)
SW1-4 and 1-5: System-on delay time setting
4
On
Off
On
Off
5
Time
On
On
Off
Off
10
30
1
5
sec (default)
sec
min
min
SW1-3: System-off delay enable/disable
On (Default)
Enable (delay time setting adjustable by SW1-6, 1-7 and 1-8 as
shown in the table below)
Off
Disable (System-off delay = 0 sec)
SW1-6, 1-7 and 1-8: System-off delay time setting
6
On
Off
On
Off
On
Off
On
Off
7
8
On
On
Off
Off
On
On
Off
Off
On
On
On
On
Off
Off
Off
Off
Time
30
1
3
5
10
15
30
1
sec (default)
min
min
min
min
min
min
hr
Note:
The OS will start the shut-down procedure after the car ignition switches off.
Please make sure that system-off delay time is sufficient to allow the OS to shut
down completely.
6
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising