Dfi OPS100-SH Manual
OPS100-SH
User’s Manual
A44900714
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2017. All Rights Reserved.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Front Panel I/O Ports.............................................................. 17
Rear Panel I/O Ports............................................................... 17
Copyright.............................................................2
I/O Ports (OPS-DB)................................................................. 18
Trademarks..........................................................2
Warranty ............................................................4
12~19V DC-in (OPS-DB).............................................................................. 18
Display Interfaces (OPS100-SH and OPS-DB)................................................ 19
USB Ports (OPS100-SH and OPS-DB)............................................................ 20
COM Port (OPS100-SH and OPS-DB)............................................................. 21
COM Port (OPS-DB)..................................................................................... 21
RJ45 LAN Port (OPS100-SH)......................................................................... 22
Audio (OPS100-SH)...................................................................................... 22
Storage and Communication Expansion Slots ............................................... 23
Static Electricity Precautions.................................4
Internal I/O Connectors.......................................................... 24
FCC and DOC Statement on Class A.....................2
About this Manual................................................4
LPC Connector (OPS100-SH)........................................................................ 24
Line-out Connector (OPS-DB)....................................................................... 24
FAN Connector (OPS100-SH and OPS-DB)..................................................... 25
FAN Connector (OPS-DB)............................................................................. 25
GPIO Connector (OPS-DB)........................................................................... 26
I2C Connector (OPS-DB).............................................................................. 26
Standby Power LED (OPS100-SH)................................................................. 27
Battery (OPS100-SH)................................................................................... 27
The TX25A-80P Connector (OPS100-SH)....................................................... 28
Signal Description........................................................................................ 29
The FX18-60S Connector (OPS100-SH)......................................................... 31
Signal Description........................................................................................ 32
Safety Measures..................................................4
Safety Precautions...............................................5
About the Package...............................................5
Chapter 1 - Introduction.......................................6
Overview: OPS100-SH...............................................................6
Overview: OPS-DB....................................................................6
Chapter 6 - BIOS Setup.......................................33
Key Features............................................................................6
Main........................................................................................................... 34
Advanced ................................................................................................... 34
Security....................................................................................................... 47
Boot........................................................................................................... 48
Exit............................................................................................................. 49
Updating the BIOS....................................................................................... 50
Notice: BIOS SPI ROM................................................................................. 50
Specifications............................................................................7
Getting to Know the OPS100-SH................................................8
Mechanical Dimensions.............................................................9
Chapter 2 - Getting Started..................................10
Chapter 7 - Supported Software...........................51
Chapter 3 - Installing the Devices.........................11
Chapter 8 - Intel AMT Settings ............................60
Installing a SODIMM............................................................... 13
Installing an M.2 Module......................................................... 13
Installing a Wi-Fi Module......................................................... 14
Chapter 4 - Board Layout and Jumper Settings.....15
Clear CMOS Data.................................................................... 15
USB Power Select................................................................... 15
AT/ATX Mode Select................................................................ 16
Chapter 5 - Ports and Connectors.........................17
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
We will not be liable for any indirect, special, incidental or damages to the product that
has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 OPS100-SH system unit
• 1 CD disk includes: Drivers and Manual
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
Optional Items
• Dispose of used batteries according to local ordinance.
•
•
•
•
•
Wall Mount kit
Power Cord
Power Adapter: 120W, 12V
Docking Board: OPS-DB
Wi-Fi + Bluetooth module: M.2 2230 802.11a/b/g/n/ac + Bluetooth 4.1, Intel AC8260, 2
cables, 2 antennas
• SSD: Intel® SSD 600P Series or M.2 2280 SATA 3.0 (64GB/128GB MLC)
• Video Capture: Yuan SC560N14K (4K@60 HDMI Capture Card PCIe x4)
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview: OPS100-SH
Front View
Antenna hole
HDD LED
COM
HDMI-in
Antenna hole USB 3.0
Wireless LED
LAN
Model Name
OPS100-SH
Processor
6th Generation Intel® Xeon® and Core™ processors
LAN
1 LAN port
COM
1 COM port
Display
1 HDMI-input
Audio
Microphone and Line-out ports
USB
4 USB 3.0 Type A ports
External Storage microSD card slot
Power Switch
Power Button Reset Button
microSD Card
Rear View
HRS FX18
Mic-in
Line-out
JAE TX25A
Overview: OPS-DB
Power Button
COM
Power-on button and reset switch
Model Name
OPS-DB
Display
1 HDMI (2.0) and 2 DisplayPort (1.2) outputs
USB
1 USB 3.0 and 2 USB 2.0 Type A ports
COM
1 COM port
Power
12~19V DC-in
Power Switch
Power-on button
USB 3.0 USB 2.0
Notes:
1. Throughout this guide the OPS100-SH may be referred to as the OPS+ Module.
2. The OPS-DB (referred to as the Docking Board) is an expansion dock, which
provides additional I/O connectivity.
DP(B)
DP(A) HDMI-out
DC-in
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
Processor
Platform Security TPM 2.0 with Intel® TXT (Intel® Trusted Execution Technology)
Intel® Xeon® Processor E3-1515M v5, Quad Core, 8M Cache, 2.8GHz (3.7GHz)
Intel® Core™ i5-6440EQ Processor, Quad Core, 6M Cache, 2.7GHz (3.4GHz)
Intel® Core™ i3-6100E Processor, Dual Core, 3M Cache, 2.7GHz
Chipset
Intel® CM236 Chipset
Intel® HM170 Chipset
Memory
• Supports dual-channel DDR4 2400/2133MHz
• Supports 4GB/8GB/16GB SODIMM modules up to a total of 32GB
Graphics
Intel® HD Gen 9 Graphics
OpenGL 5.0, DirectX 12, OpenCL 2.1
• Supports these codecs:
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265,
VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
• Output displays:
1 x HDMI-input
2 x DP (1.2): resolution up to 4096x2160 @ 60Hz
1 HDMI-output (2.0): resolution up to 3840x2160 @ 60Hz
• Triple display: HDMI + 2 DP
Audio
• Realtek ALC888
• Audio ports: Mic-in and Line-out
Wireless
Connectivity
• 1 x M.2 (Type 2230 E Key) (PCIe/USB) for wireless modules
Storage
• 1 x M.2 (Type 2280 M Key) (PCIe x4/SATA) for SSD modules
• 1 x micro SD Card Slot
Ethernet
1 x Intel® I219LM PCIe with iAMT 11.6 (10/100/1000Mbps)
Expansion
1 x PCIe x4 expansion slot (on the OPS-DB Docking Board)
Front and rear
Panel I/O Ports
• Front Panel
1 x GbE (RJ-45)
1 x RS-232 (DB-9)
4 x USB 3.0 (type A)
1 x HDMI-input
1 x Line-out
1 x Mic-in
1 x Power Button
1 x Reset Button
2 x Wi-Fi Module Antenna Holes
• Rear Panel
The JAE TX25A-80P connector:
1 x HDMI 2.0
1 x DP 1.2
2 x USB 2.0
1 x USB 3.0
1 x 12~19V DC-in
Power
• Power input voltage: 12~19V DC-in (DC-in jack connector)
Cooling System
• Heatsink with fan
Environment
• Operating Temperature:
0°C to 45°C
• Storage Temperature:
-40 to 85°C
• Relative Humidity:
10 to 90% RH (non-condensing)
Construction
• Aluminum + SGCC
Dimensions
• 180mm x 30mm x 119mm (W x H x D)
Weight
• TBD
OS Support
• Windows 10 Enterprise (64-bit)
• Windows 8.1
Watch Dog Timer System Reset, Programmable via Software from 1 to 255 Seconds
Standards and
Certifications
Packaged Shock (Drop): 6 face drops, 2 corner drops and 3 edge drops
for a total of 11 drops from a height of 36 inches if package weight < 20
pounds (30 inches if package weight ≥ 20 to < 40 pounds)
Packaged Vibration: 0.015 g2/Hz from 5 Hz to 40 Hz, Sloping to 0.00015
g2/Hz at 500 Hz, Input acceleration is 1.09 gRMS, 1 hour per axis for all 3
axes for all samples; Random control limit tolerance is ± 3 dB.
The Hirose FX18-60S connector:
1 x DP 1.2
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the OPS100-SH
Front View
Antenna Hole(1)
HDD LED
COM
HDMI-in
Antenna Hole(1) USB 3.0 Wireless LED(2)
Power Button Reset Button
microSD Card
Power Button with LED (Green)
Press this button to power on or power off the system.
Rear View
LAN
HRS FX18
JAE TX25A
Mic-in
Line-out
HRS FX18/JAE TX25A
USB 3.0 Ports
These ports connect USB 3.0 or USB 2.0/1.1 devices.
The OPS+ Module enables the integration of a pluggable module and a display panel
by employing a defined interconnect based on the JAE and HRS combo plug and their
receptacle connectors.
HDMI-in Port
This port can be used to connect an HDMI source (e.g. an HDMI port of a computer) and let
the signal pass through to another output display.
For detailed pin assignments and connector specifications, refer to Chapter 4 and 5.
Reset Button
Press this button to reset the system without turning on or off the power.
COM Port
This port connects serial devices.
LAN Port
This port connects the system to a local area network (LAN).
Microphone/Line-out Ports
This port connects audio devices such as microphones and speakers.
Notes:
1. The OPS+ Module is equipped with a Wi-Fi module to provide Wi-Fi connectivity.
Please install antennas to these SMA connectors.
2. There may not be indicator light depending on the installed Wi-Fi module; for
example, the LED will not be lit for Intel® Dual Band Wireless-AC 8260.
microSD Card Slot
This port connects a microSD card that complies with SD specification v1.0/v1.1/v2.0 SDHC.
Wireless LED (2)
The wireless LED indicates the wireless connection status. The LED behavior depends on the
wireless module used.
HDD LED (Green)
This LED indicates the status of the disk drive.
HDD State
Disk access activity
HDD present or HDD not present
LED Behavior
Blink
Off
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
Chassis Dimensions
Motherboard Dimensions
The overall dimensions of the OPS+ Module exclusive of the front panel frame is 180 x 30 x
119 mm (W x H x D). The following illustrations show the dimensions of the OPS+ Module as
well as the dimension and location of the front panel screw holes:
The following illustration shows the overall dimensions of the motherboard and the
components with their relative positions.
165.00
106.00
109.59
120.00
115.70
30.00
180.00
54.59
Rear View
45.60
0.00
31.95
200.00
111.90
103.40
102.00
97.30
119.00
89.15
81.05
56.43
34.15
192.00
156.50
23.00
4.50
14.50
144.00
5.00
122.79
5.00
4.50
107.98
14.50
64.75
3.00
2.70
7.00
17.00
10.40
2.95
1.50
50.54
91.50
2-R2.25
2-R2.25
20.00
15.74
10.97
0.00
Right View
33.50
Top View
17.00
Left View
Front View
Unit: mm
Unit: mm
9
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
Wireless Antennas (if wireless module is installed)
AC power adapter
CD-ROM drive (for installing software/drivers)
Installing Devices
The following are devices that can be installed in the system.
•
•
•
•
microSD card
M.2 SSD card
M.2 wireless card
M.2 capture card
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the type
of hard disk drive.
1.
2.
Power-on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing the Operating System
Most operating system software are provided in a CD therefore you need to install a CD-ROM
drive in order to use the CD. Alternatively, you can remotely install an operating system using
Intel® AMT.
Please refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
10
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing the Devices
Installing the OPS100-SH into a Display
2.
Secure the module by attaching two screws on the front panel.
Observe the following precautions and guidelines before starting any installation procedures
described in this chapter:
1.
Make sure the system and all other peripheral devices connected to it have been poweredoff.
2.
Disconnect all power cords from all power sources and cables. Failure to disconnect power
before you open the system or perform any procedures can result in or electrical shock or
equipment damage.
Integrating a computing system into a digital signage display is made easy by standardizing the
connectors and signals between an OPS+ Module and an OPS-compliant display.
Mounting screw holes
Note that the OPS+ Module does not support hot swapping; do not power on the display before
the installation is complete. Please use the following steps to install the OPS+ Module into the
display panel:
1.
Align the OPS+ Module with the slot of the display and slide the module into the slot. Note
that the venting holes should face outward to allow ambient airflow.
3.
Power on the display panel. The OPS+ Module should be automatically powered on.
Venting area of the panel
Venting holes
Note:
The location of the OPS slot may be at the side or at the bottom of the display panel
depending on the design.
11
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing the OPS100-SH into the OPS-DB
Removing the Chassis Cover
The OPS+ Module has an accompanying Docking Board and allows it to serve as a standalone
computing system. The plug and unplug mechanism between the OPS+ Module and the
Docking Board utilizes the combo connector at the back of the module. Please use the
following steps to install the OPS+ Module into the Docking Board:
1.
Observe the precautions at the beginning of this chapter before proceeding with the
procedure. Make sure that all power cords and cables have been disconnected.
2.
The 2 mounting screws on the sides and top cover of the system chassis, and the 3 screws
that affix the front panel to the chassis should all be removed to open the system. Put these
screws in a safe place for later use.
1.
Align the OPS+ Module with the slot of the Docking Board and slide the module into the
slot. Note that the venting holes should face upward to allow ambient airflow.
2.
Secure the module by tightening the thumbscrews on the front panel.
Chassis screw
Docking Board
Thumbscrew
Chassis screw
Thumbscrew
3.
Connect the included AC power adapter. Turn on the system by pressing the power switch.
Chassis screw
3.
Lift the cover up to open the system.
Power switch
12
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
Installing a SODIMM
Installing an M.2 Module
The SODIMM sockets are located on the top side of the system board; it can be accessed after
removing the chassis cover. The memory module requirements are as follows:
• 260-pin DDR4 SODIMMs
• 2400 or 2133 MHz
• Non-ECC
The onboard M.2 Type 2280 connector (M Key) is located on the back side of the system board.
It supports SATA 3 modules (6.0 Gb/s) and M.2 PCI Express modules up to PCIe NVMe 3.0 x4.
The system may come with a pre-installed Intel® Solid State Drive 600P Series available in a variety of capacities.
To install a M.2 module, follow these steps:
To install the SO-DIMMs, follow these steps:
1. Open the system by following the "Removing the Chassis Cover" procedure.
2.
1.
Grasp the module by its edges and align the memory’s notch with the socket’s key; then
insert the memory into the socket at an angle and push it down until the retaining clips
snap into place.
CPU fan
SODIMM
Notes:
1. The system supports dual-channel configuration. To enable dual-channel,
populate both SODIMM sockets.
2.
Grasp the module by its edges and align the notch of the M.2 module with the key in the
connector.
M.2 SSD connector
The SODIMM sockets can only accept DDR4 memory modules. Please do not
install other types of memory modules.
13
Chapter 3 Installing the Devices
www.dfi.com
Chapter 3
2.
Installing a Wi-Fi Module
Insert the M.2 module into the connector.
The system is also equipped with an M.2 Type 2230 connector (E Key). It supports PCIe and
USB signals for wireless communication modules. The system may come with a pre-installed
Intel® Dual Band Wireless-AC 8260, which complies with Wi-Fi 802.11ac and Bluetooth 4.2
standards.
To install the M.2 module, follow these steps:
3.
1.
Grasp the module by its edges and align the notch of the M.2 module with the key in the
connector.
2.
Insert the M.2 module into the connector.
3.
Secure the card to the riser screw on the board using the screw shipped with the M.2
module.
Secure the card to the riser screw on the board using the screw shipped with the M.2
module.
M.2 wireless module
M.2 SSD card
14
Chapter 3 Installing the Devices
www.dfi.com
Chapter 4
Chapter 4 - Board Layout and Jumper Settings
OPS-DB
OPS100-SH
USB Power Select
Clear CMOS Data
COM 1
LAN 1
Line-out
Mic-in
1
MicroSD
Clear
CMOS
(J23)
HRS FX18-60P
Reset
USB 3.0
1
USB 3.0
Power-on
JAE TX24A-80R
111
140
81
110
CPU Fan (J1)
Battery (J3)
2
1
1
Buzzer
SYS Fan (J3)
IC
IC
2
1
GPIO (J4)
A2
A1
B1
B2
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
USB PWR
(J15) 3
USB 2.0
1
2
41
42
40
79
80
J23
3
3
1
1
1-2 On:
Normal
DC-in
110
140
3
J16
(for the USB 2.0 ports)
DC-in
81
111
39
4
DPA
J15
(for the USB 3.0 port)
SPI Flash BIOS
JAE TX25A-80P
HDMI 1
3
DPB
1
LPC
HRS FX18-60S
1
+12V Slide Switch
COM 1
13
2
1
2
AT/ATX mode
(J17)
Power-on
14
USB PWR
(J16) 3
1
USB 3.0
CM236/HM170
1
6
I2C (J6)
1
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
DDR4_2 SODIMM
Intel
DDR4_1 SODIMM
Intel
80
42
41
2
1
3 2 1
1-2 On: +5V
2-3 On:
Clear CMOS
3 2 1
2-3 On:
+5V_standby
(default)
J15 and J16 are used to select the power for the Docking Board’s USB port 3.0 and USB ports
2.0 respectively. Selecting +5V_standby will allow you to use USB devices to wake up the
system.
You can reconfigure the system with the default values stored in the ROM BIOS if you encounter the following situations:
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper back to its
default setting, pins 1 and 2 On.
3. Now plug the power cord and power on the system.
15
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
OPS-DB
AT/ATX Mode Select
HRS FX18-60P
JAE TX24A-80R
111
140
81
110
1
SYS Fan (J3)
1
6
I2C (J6)
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
USB PWR
(J15) 3
USB PWR
(J16) 3
1
1
2
1
1
AT/ATX mode
(J17)
+12V Slide Switch
DPB
HDMI 1
USB 3.0
3
Power-on
4
3
DPA
USB 2.0
DC-in
COM 1
J17
1
2
3
1-2 On: ATX mode
(default)
1
2
3
2-3 On: AT mode
J17 is used to select the power-on mode: AT or ATX (default). The Docking Board is equipped
with a hard switch to provide AT power scheme. With the AT mode, you need to manually
turn off the system with the power switch; whereas in the ATX mode, the system can be powered off using the shut-down function provided by the OS.
16
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
Front Panel I/O Ports
Rear Panel I/O Ports
HRS FX18
HDD LED
JAE TX25A
Antenna hole
HDMI-in
COM
Antenna hole USB 3.0
Wireless LED
LAN
The rear panel I/O consists of the following ports:
Power Button Reset Button
microSD Card
• The right angle blind mate plug connector (the JAE TX25A-80P connector)
• The right angle mate plug connector (the HRS FX18-60S connector)
Line-out
Mic-in
The front panel I/O consists of the following ports:
•
•
•
•
•
•
•
•
•
•
Power button (green)
Four USB 3.0 ports
HDMI-in port
HDD LED (green)
Wireless LED (blue)
Reset button
microSD card slot
COM (RS232) serial port
LAN port
Mic-in and line-out jack
17
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
I/O Ports (OPS-DB)
Power Button
COM
12~19V DC-in (OPS-DB)
USB 3.0 USB 2.0
HRS FX18-60P
140
81
110
1
SYS Fan (J3)
DP(B)
DP(A) HDMI-out
1
6
I2C (J6)
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
USB PWR
(J15) 3
DC-in
USB PWR
(J16) 3
1
1
2
1
1
The Docking Board provides these additional I/O ports:
AT/ATX mode
(J17)
+12V Slide Switch
Power-on
DPB
HDMI 1
USB 3.0
4
3
DPA
COM 1
USB 2.0
DC-in
Two DisplayPort outputs
HDMI-output port
COM (RS232) serial port
One USB 3.0 and two USB 2.0 ports
DC-in jack
3
•
•
•
•
•
JAE TX24A-80R
111
DC-in
Connect a DC power cord to this DC-in jack. Using a voltage more than the recommended
range may fail to boot the system or damage the system board.
18
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
Display Interfaces (OPS100-SH and OPS-DB)
Display Interfaces (OPS100-SH)
Display Interfaces (OPS-DB)
HRS FX18-60P
110
81
HDMI-in
1
SYS Fan (J3)
COM 1
LAN 1
Mic-in
Line-out
1
MicroSD
Clear
CMOS
(J23)
1
Battery (J3)
2
1
1
GPIO (J4)
A2
A1
B1
B2
6
I2C (J6)
Reset
USB 3.0
USB 3.0
JAE TX24A-80R
140
111
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
Power-on
USB PWR
(J15) 3
CPU Fan (J1)
2
USB PWR
(J16) 3
1
1
2
1
AT/ATX mode
(J17)
+12V Slide Switch
USB 3.0
DDR4_2 SODIMM
CM236/HM170
DPB
Power-on
USB 2.0
COM 1
DP
4
3
DPA
DP
DC-in
IC
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
DDR4_1 SODIMM
3
Intel
HDMI 1
Intel
14
1
1
Buzzer
HDMI-out
13
1
2
LPC
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
110
111
140
1
2
41
42
39
40
79
80
DC-in
81
HDMI-in Port (OPS100-SH)
Using the Docking Board, the system supports triple display with the following output interfaces:
The HDMI-in port can be enabled using the BIOS setup utility and be used to connect an
audio/video source, such as a HDMI-compliant output of a PC, and let the signal pass through
the device. The default mode for HDMI-in is disabled. You can configure its mode with the
BIOS Setup Utility.
HDMI-out Port (OPS-DB)
The HDMI port, which carries both digital audio and video signals, is used to connect an LCD
monitor or a digital TV that has an HDMI port.
DP Ports (OPS-DB)
The DisplayPort is a digital display interface used to connect a display device. The interface,
developed by VESA and backwards compatible with VGA, DVI and HDMI, delivers higher performance than any other digital interfaces.
BIOS Setting
Configure the display devices in the Advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to Chapter 6 for more information.
Driver Installation
Install the graphics driver. Refer to Chapter 7 for more information.
19
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
USB Ports (OPS100-SH and OPS-DB)
USB Ports (OPS100-SH)
USB Ports (OPS-DB)
USB
HRS FX18-60P
COM 1
LAN 1
Line-out
Mic-in
1
MicroSD
Clear
CMOS
(J23)
Battery (J3)
140
81
110
Reset
USB 3.0
1
USB 3.0
JAE TX24A-80R
111
Power-on
1
CPU Fan (J1)
2
SYS Fan (J3)
1
1
6
I2C (J6)
Buzzer
Intel
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
DDR4_2 SODIMM
AT/ATX mode
(J17)
DPB
HDMI 1
Power-on
4
3
DPA
DC-in
USB 2.0
COM 1
14
1
+12V Slide Switch
3
CM236/HM170
1
2
USB 3.0
IC
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
USB PWR
(J16) 3
1
1
Intel
DDR4_1 SODIMM
USB PWR
(J15) 3
13
USB 3.0
1
2
USB 2.0
LPC
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
110
111
140
1
2
41
42
39
40
79
80
DC-in
81
The Docking Board is equipped with one USB 3.0 and two USB 2.0 ports. The USB 3.0 can
transfer data up to 5 Gbps whereas the USB 2.0 can transfer data up to 480Mbps.
The OPS100-SH is equipped with four USB 3.0 port. USB devices allow data exchange between
your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
BIOS Setting
Configure the USB ports in the Advanced menu (“USB Configuration” submenu) of the BIOS.
Refer to Chapter 6 for more information.
Driver Installation
You may need to install the proper drivers in your operating system to use USB devices. Refer
to Chapter 7 for more information.
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function, you
need to select power for the USB ports; refer to Chapter 4 for more information.
20
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
COM Port (OPS100-SH and OPS-DB)
COM Port (OPS-DB)
RXD
TXD
DTR
GND
DCD
COM Port (OPS100-SH)
1 2 3 4 5
HRS FX18-60P
DSR
RTS
CTS
6 7 8 9
140
81
110
1
RI
JAE TX24A-80R
111
SYS Fan (J3)
1
6
I2C (J6)
COM 1
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
USB PWR
(J15) 3
COM 1
LAN 1
USB 3.0
USB 3.0
Power-on
DDR4_2 SODIMM
COM 1
RXD
TXD
2
1
3
GND
DDR4_1 SODIMM
IC
IC
13
USB 2.0
COM 1
CM236/HM170
4
DPA
DC-in
Intel
DPB
HDMI 1
USB 3.0
3
Buzzer
14
1
+12V Slide Switch
1
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
2
AT/ATX mode
(J17)
Power-on
CPU Fan (J1)
2
Intel
1
Reset
1
Battery (J3)
USB PWR
(J16) 3
1
1
Line-out
Mic-in
1
MicroSD
Clear
CMOS
(J23)
A32
A31
B31 Line_out
B32
(J5) 1
1 2 3 4 5
LPC
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
110
111
140
1
2
41
42
39
40
79
80
DC-in
81
6 7 8 9
This COM port is an RS232 port and provides 9-pin serial communication.
Unlike a normal 9-pin RS232 serial port, this COM port only provides RX and TX communication links.
BIOS Setting
BIOS Setting
Configure the serial ports in the “Advanced” menu (Super I/O submenu) of the BIOS. Refer
to Chapter 6 for more information.
Configure the serial ports in the “Advanced” menu (Super I/O submenu) of the BIOS. Refer to
Chapter 6 for more information.
21
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
RJ45 LAN Port (OPS100-SH)
ACT/Link LED
LAN 1
Mic-in
COM 1
COM 1
USB 3.0
Power-on
Mic-in
LAN 1
USB 3.0
1
Battery (J3)
Line-out
Reset
Line-out
Line-out
Mic-in
1
MicroSD
Clear
CMOS
(J23)
CPU Fan (J1)
LAN 1
Speed LED
Audio (OPS100-SH)
2
1
MicroSD
Clear
CMOS
(J23)
Battery (J3)
1
Reset
USB 3.0
1
USB 3.0
Power-on
CPU Fan (J1)
2
Buzzer
1
Intel
Buzzer
14
1
13
1
2
LPC
DDR4_2 SODIMM
CM236/HM170
13
2
IC
14
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
IC
CM236/HM170
Intel
DDR4_1 SODIMM
IC
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
DDR4_2 SODIMM
Intel
DDR4_1 SODIMM
Intel
LPC
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
111
140
1
2
41
42
40
79
80
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
39
81
110
111
140
1
2
41
42
39
40
79
80
DC-in
110
DC-in
81
Features
•
Front Audio
One Intel® I219LM PCI Express Gigabit Ethernet controller with support for iAMT11.6 (The
SKU with the Intel® Core™ i3 processor does not support iAMT.)
The system board is equipped with 2 audio jacks:
The LAN port allows the system board to connect to a local area network through an Ethernet
link and enables remote system management and configurations with the Intel® Active Management Technology (AMT). Please refer to the following table for LED indications.
Activity/Link LED
LED Behavior
Off
Blinking
On
Description
No link
Data Activity
Link
Speed LED
LED Behavior
Off
Green
Orange
Description
10Mbps connection
100Mbps connection
1Gbps connection
•
Line-out Jack
This jack is used to connect a headphone or external speakers with audio amplifiers.
•
Mic-in Jack
This jack is used to connect an external microphone.
Driver Installation
Install the audio driver. Refer to Chapter 7 for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 7 for more information.
22
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
Storage and Communication Expansion Slots
M.2 Slots (OPS100-SH)
(OPS100-SH and OPS-DB)
The M.2 card slots on the back side of the system board are used to install M.2 (NGFF) modules. The M.2 Type 2280 (M Key) slot can be inserted with either an mSATA SSD card or a
PCIe NVMe card with the form factor of M.2 22x80 mm. However, the PCIe Gen 3.0 x4 is
capable of up to 3940 MB/s transfer speed whereas SATA 3.0 can only provide up to 600MB/s
transfer speed.
The M.2 Type 2230 (E Key) slot can be inserted with a Wi-Fi module with the form factor of
M.2 22x30 mm to provide wireless communication capability.
microSD Connector (OPS100-SH)
This connector supports SD specification v1.0/v1.1/v2.0 SDHC and can connect a Micro Secure
Digital memory card up to 32 GB to moderately expand system capacity. In contrast to the
internal M.2 slots, the microSD connector can be accessed externally.
M.2 Type 2280-S2-M
(PCIe/SATA)
M.2 Type 2230-D2-E
(PCIe/USB)
HRS FX18-60P
74
32
22
G1
23
33
75
JAE TX24A-80R
2
M1
M2
G2
111
140
81
110
2
1
96
1
97
M1
J22
75
67
1
57
1
SYS Fan (J3)
1
6
I2C (J6)
2
1
GPIO (J4)
A2
A1
B1
B2
PCIE1(PCIe 3.0 x4)
M.2 Type 2280 connector (for both PCI
Express x4 and SATA 3.0 interfaces)
M.2 Type 2230 connector (for both PCI
Express and USB 2.0 interfaces)
80
42
41
2
1
A32
A31
B31 Line_out
B32
(J5) 1
USB PWR
(J15) 3
USB PWR
(J16) 3
1
1
2
1
1
AT/ATX mode
(J17)
LAN 1
Line-out
Mic-in
1
COM 1
MicroSD
Reset
USB 3.0
1
Battery (J3)
USB 3.0
4
3
DPA
USB 2.0
DC-in
COM 1
DPB
HDMI 1
USB 3.0
Power-on
Clear
CMOS
(J23)
+12V Slide Switch
3
microSD card slot
Power-on
CPU Fan (J1)
2
1
Buzzer
IC
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
CM236/HM170
14
13
2
1
PCIE1
PCI Express x4
DDR4_2 SODIMM
Intel
DDR4_1 SODIMM
Intel
PCIe Expansion Slot (OPS-DB)
The expansion slot provides PCIe 3.0 x4 bandwidth and can be used to insert a PCIe card for
storage expansion or to provide network connectivity.
LPC
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
110
111
140
1
2
41
42
39
40
79
80
DC-in
81
23
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
Internal I/O Connectors
Line-out Connector (OPS-DB)
LPC Connector (OPS100-SH)
HRS FX18-60P
COM 1
LAN 1
Line-out
Mic-in
1
MicroSD
Clear
CMOS
(J23)
111
81
110
Reset
USB 3.0
1
Battery (J3)
JAE TX24A-80R
140
USB 3.0
1
Power-on
SYS Fan (J3)
CPU Fan (J1)
2
1
Buzzer
1
6
I2C (J6)
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
Intel
DPB
DDR4_2 SODIMM
DDR4_1 SODIMM
1
81
110
111
140
Pins
1
2
41
42
40
79
80
Line-out (J5)
Pin Assignment
1
7
L_AD3
14
5V
6
3V3
13
5VSB
5
L_FRAME#
12
GND
4
L_AD0
11
INT_SERIRQ
3
L_RST#
10
Key
2
L_AD1
9
L_AD2
1
L_CLK
8
GND
Pins
Pin Assignment
5
AZ_LINEOUT_L
4
Audio Ground
3
AZ_LineOut_R
2
No Connect
1
No Connect
39
DC-in
Pin Assignment
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
Pins
DC-in
USB 2.0
LPC
1
3
13
2
2
4
DPA
COM 1
13
14
1
+12V Slide Switch
HDMI 1
Power-on
14
1
2
USB 3.0
CM236/HM170
USB PWR
(J16) 3
1
AT/ATX mode
(J17)
3
IC
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
USB PWR
(J15) 3
1
Intel
A32
A31
B31 Line_out
B32
(J5) 1
The Line-out connector provides both left and right channel for audio output.
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s
transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O
components within the system, which are provided by the embedded controller. It is also used
to interface Trusted Platform Module (TPM) devices. For more information about LPC bus,
please refer to the Intel® Low Pin Count Interface Specification. The table above indicates the
pin assignments of the LPC connector.
24
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
FAN Connector (OPS100-SH and OPS-DB)
FAN Connector (OPS100-SH)
FAN Connector (OPS-DB)
COM 1
LAN 1
Line-out
Mic-in
1
USB 3.0
1
Battery (J3)
HRS FX18-60P
Reset
MicroSD
Clear
CMOS
(J23)
USB 3.0
JAE TX24A-80R
Power-on
CPU Fan (J1)
111
140
81
110
2
1
Buzzer
1
Intel
IC
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
CM236/HM170
1
6
I2C (J6)
DDR4_2 SODIMM
Intel
DDR4_1 SODIMM
SYS Fan (J3)
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
USB PWR
(J15) 3
USB PWR
(J16) 3
1
1
2
1
1
AT/ATX mode
(J17)
+12V Slide Switch
13
DPB
Power-on
SPI Flash BIOS
JAE TX25A-80P
110
140
39
1
2
41
42
Pins
Pin Assignment
4
Speed Control
3
Sense
2
Power
1
Ground
40
79
80
DC-in
81
111
3
DC-in
USB 2.0
COM 1
LPC
HRS FX18-60S
4
DPA
1
2
HDMI 1
USB 3.0
3
14
CPU FAN (J1)
SYS FAN (J3)
4
Pins
Pin Assignment
3
No Connect
2
PWM Control
1
Ground
1
1
3
The fan connector is used to connect a cooling fan for the system.
The fan connector is used to connect the cooling fan of a CPU heatsink.
25
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
GPIO Connector (OPS-DB)
HRS FX18-60P
110
81
SYS Fan (J3)
JAE TX24A-80R
HRS FX18-60P
140
111
1
I2C Connector (OPS-DB)
2
1
GPIO (J4)
A2
A1
B1
B2
1
6
I2C (J6)
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
USB PWR
(J15) 3
140
81
110
1
A32
A31
B31 Line_out
B32
(J5) 1
SYS Fan (J3)
USB PWR
(J16) 3
1
JAE TX24A-80R
111
1
6
I2C (J6)
2
1
GPIO (J4)
A2
A1
B1
B2
80
42
41
2
1
PCIE1(PCIe 3.0 x4)
A32
A31
B31 Line_out
B32
(J5) 1
1
2
1
USB PWR
(J15) 3
USB PWR
(J16) 3
1
1
2
1
AT/ATX mode
(J17)
AT/ATX mode
(J17)
+12V Slide Switch
DPA
Power-on
DPB
4
3
DPA
USB 2.0
COM 1
DC-in
DC-in
USB 2.0
COM 1
HDMI 1
USB 3.0
3
3
DPB
HDMI 1
USB 3.0
3
Power-on
4
1
1
+12V Slide Switch
1
GPIO (J4)
Pins
Pin Assignment
2
GPIO
1
Ground
I2C (J6)
6
1
Pins
Pin Assignment
5
No Connect
4
I2C_Data
3
I2C_CLK
2
Ground
1
3V3SB
The General-purpose input/output (GPIO) is a software-programmable and multi-purpose
interface, with configurable pull-up or pull-down for each pin. The GPIOs are useful in many
embedded applications to provide monitoring and control functions of connected devices.
The I2C bus is a multi-device and serial communication bus. It can be used to provide shortdistance communication among low-speed peripheral ICs.
26
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
Standby Power LED (OPS100-SH)
Battery (OPS100-SH)
COM 1
1
Power-on
Ground
Battery
CPU Fan (J1)
2
1
Buzzer
1
MicroSD
Clear
CMOS
(J23)
Battery (J3)
1
1
CM236/HM170
14
1
13
1
2
LPC
DDR4_2 SODIMM
DDR4_2 SODIMM
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
IC
DDR4_1 SODIMM
Intel
13
2
Power-on
Buzzer
IC
IC
CM236/HM170
14
USB 3.0
Intel
IC
Xeon ® E3-1515M v5
Core™ i5-6440EQ
Core™ i3-6100E
USB 3.0
CPU Fan (J1)
2
Intel
Intel
Reset
1
DDR4_1 SODIMM
Battery (J3)
USB 3.0
LAN 1
LAN 1
USB 3.0
Line-out
Reset
Mic-in
Line-out
Mic-in
1
COM 1
MicroSD
Clear
CMOS
(J23)
LPC
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
111
140
1
2
41
42
40
79
80
SPI Flash BIOS
JAE TX25A-80P
HRS FX18-60S
39
81
110
111
140
39
1
2
41
42
40
79
80
DC-in
110
DC-in
81
Standby
Power LED
Connect to the battery connector
Battery
This LED will be lit when the system is in the standby mode. It indicates that there is power
on the system board. Power off the system and then unplug the power cord prior to installing
any devices. Failure to do so will cause severe damage to the motherboard and components.
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
27
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
The TX25A-80P Connector (OPS100-SH)
25
GND
Ground
-
65
GND
Ground
-
24
TMDS0_1+
DVI-D
OUT
64
USB_PP1
USB
I/O
23
TMDS0_1-
DVI-D
OUT
63
USB_PN1
USB
I/O
22
GND
Ground
-
62
GND
Ground
-
21
TMDS0_0+
DVI-D
OUT
61
USB_PP2
USB
I/O
Audio: left and right Channel
20
TMDS0_0-
DVI-D
OUT
60
USB_PN2
USB
I/O
USB: 1*USB 3.0 and 3*USB 2.0
19
GND
Ground
-
59
GND
Ground
-
Control and Sensors: 1*UART and Consumer Electronics Control (CEC, note that the OPS100-SH
does not support this function)
18
TMDS0_CLK+
DVI-D
OUT
58
StdA_SSTX+
USB3.0
OUT
17
TMDS0_CLK-
DVI-D
OUT
57
StdA_SSTX-
USB3.0
OUT
16
GND
Ground
-
56
GND
GND
-
15
DDP_HPD
DisplayPort
IN
55
StdA_SSRX+
USB3.0
IN
The OPS+ Module enables the integration of a pluggable module and a display panel by
employing the defined interconnect based on the JAE and HRS combo plug and their receptacle
connectors. The right angle blind mate plug connector (p/n: JAE TX25A-80P-LT-H1E) should
be mated with the receptacle connector (p/n: JAE TX24A-80R-LT-H1E); together, they provide
interfacing for the following functions:
Power: DC-IN +12V~+19V@12A max
Display Interface: 2*HDMI 2.0 (or DVI or DP, 4K at 60Hz)
Control and Management Signals: the OPS+ Module power status, power-on via display panel,
OPS+ Module detect, system fan control, and device reset.
The following table lists the pin assignments of the 80-pin JAE connector:
Pins
Pin Assignment
Description
I/O(1)
Pins
Pin Assignment
Description
I/O
14
DDP_AUXP
DisplayPort
I/O
54
StdA_SSRX-
USB3.0
IN
40
+12V~+19V
Power
-
80
GND
Ground
-
13
DDP_AUXN
DisplayPort
I/O
53
GND
Ground
-
39
+12V~+19V
Power
-
79
GND
Ground
-
12
GND
Ground
-
52
UART_TXD
UART 3.3V
OUT
11
DDP_0P
DisplayPort
OUT
51
UART_RXD
UART 3.3V
IN
38
+12V~+19V
Power
-
78
GND
Ground
10
DDP_0N
DisplayPort
OUT
50
SYS_FAN
System Fan Control
OUT
37
+12V~+19V
Power
-
77
GND
Ground
9
GND
Ground
-
49
RSVD
Reserved
-
36
+12V~+19V
Power
-
76
GND
Ground
8
DDP_1P
DisplayPort
OUT
48
RSVD
Reserved
-
35
+12V~+19V
Power
-
75
GND
Ground
7
DDP_1N
DisplayPort
OUT
47
RSVD
Reserved
-
34
+12V~+19V
Power
-
74
PWR_STATUS
PowerGood
OUT(OC)(2)
6
GND
Ground
-
46
RSVD
Reserved
-
33
+12V~+19V/NC
Power/NC
-
73
PS_ON#
Pluggable Signal ON
IN
5
DDP_2P
DisplayPort
OUT
45
RSVD
Reserved
-
32
GND
Ground
-
72
PB_DET
Pluggable Board Detect
OUT
4
DDP_2N
DisplayPort
OUT
44
RSVD
Reserved
-
31
DVI0_HPD
DVI-D
IN
71
Not Available
Not Available
I/O
3
GND
Ground
-
43
RSVD
Reserved
-
30
DVI0_DDC_CLK
DVI-D
I/O
70
AZ_LINEOUT_R
Audio-R ch
OUT
2
DDP_3P
DisplayPort
OUT
42
RSVD
Reserved
-
29
DVI0_DDC_DATA
DVI-D
I/O
69
AZ_LINEOUT_L
Audio-L ch
OUT
1
DDP_3N
DisplayPort
OUT
41
RSVD
Reserved
-
28
GND
Ground
-
68
GND
Ground
-
27
TMDS0_2+
DVI-D
OUT
67
USB_PP0
USB
I/O
26
TMDS0_2-
DVI-D
OUT
66
USB_PN0
USB
I/O
Notes:
(1) The I/O column definition is in reference to the OPS+ pluggable board.
(2) OC= Open Collector.
28
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
Signal Description
Audio Signals
Here is the detailed description of each signal passing through the TX25A-80P connector.
Pin No.
Signal
I/O
Description
-
The Pluggable Module supports a voltage range of +12V~+19V DC IN
(mandatory). The maximum total current rating shall not exceed 12A (1A
per pin). The in-rush current of the pluggable module shall not exceed
14A to ensure successful power up operation.
It is mandatory for the OPS-C manufacturers to provide a Power Rating
label on the Pluggable Module and/or product brief/catalog which
indicates the power consumption of the module (e.g. 40W). Display
manufacturers must indicate the power supply spec for OPS-C on the
product brief/catalogue (e.g. 16V/4A)
3, 6, 9, 12, 16,
19, 22, 25,28,
32, 53, 56, 59,
62, 65, 68, 75,
76, 77, 78, 79,
80
+12V~+19V
GND
AZ_LINEOUT_R
69
AZ_LINEOUT_L
O
Audio Right Channel
Audio Left Channel
USB Interface
Power and Ground
33, 34, 35, 36,
37, 38, 39, 40
70
-
Ground
67
66
64
63
61
USB_PP0
USB_PN0
USB_PP1
USB_PN1
USB_PP2
60
USB_PN2
58
StdA_SSTX+
57
StdA_SSTX-
55
StdA_SSRX+
54
StdA_SSRX-
I/O
USB2.0 Differential Pair
USB3.0 SuperSpeed Transmitter Differential Pair
O
USB3.0 SuperSpeed Transmitter Differential Pair
I
USB3.0 SuperSpeed Receiver Differential Pair
UART Interface
52
UART_TXD
O
51
UART_RXD
I
Transmitted UART data from pluggable board, UART 3.3V LVTTL signal.
Assign as COM 1 for the UART Port in the pluggable module.
Received UART data for pluggable board, UART 3.3V LVTTL signal.
Assign as COM 1 for the UART Port in the pluggable module.
OPS Control Interface
74
DVI-D/TMDS
31
DVI_HPD
I
30
DVI_DDC_CLK
I/O
29
DVI_DDC_DATA
27
TMDS2+
26
TMDS2-
24
TMDS1+
23
TMDS1-
21
TMDS0+
20
TMDS0-
18
TMDS_CLK+
17
TMDS_CLK-
PWR_STATUS
OC
DVI Hot Plug Detect. Active High
O
Display Data Channel Signals
DVI Control Data and Clock. These are single-ended control signals used
for communications between the chipset DVI display port and a panel
device (Sink).
TMDS Data Channel
O
TMDS Clock Channel
High: Pluggable board power off state
Low: Pluggable board power on state
73
PS_ON#
I
72
PB_DET
O
71
CEC
DisplayPort
15
14
13
11
10
8
7
5
4
2
1
DDP_HPD
DDP_AUXP
DDP_AUXN
DDP_0P
DDP_0N
DDP_1P
DDP_1N
DDP_2P
DDP_2N
DDP_3P
DDP_3N
I
I/O
O
2 Ports
Hardware
Installation
Chapter 5
and Connectors
Power status indication signal or Power Good status of the pluggable
board. This pin shall be Open Collector and pull up to +3.3V on the
docking/control board side.
Display Port Hot Plug Detect. Active High
Display Port Auxiliary Channel
Display Port Data Channel
I/O
Pluggable Signal ON: This is meant for signal initiation to power ON or
boot up the Pluggable Module. PS_ON# shall be asserted at least 500ms
after power is delivered from PSU to the board via the JAE connector (G3
to S5 state). Pull up to +3.3V on the pluggable board.
A pulse width present on the PS_ON# shall be detected and responded
to within 200ms to ensure successful operation.
Use case: Power button initiation from the panel control board to the
Pluggable board via, for example, IR remote control ON. The PWRBTN#
pin on the Intel ICH/PCH can be utilized for this purpose. PWRBTN# has
a 16 ms of internal debounce logic.
External debouncing circuit is not required. Refer to the respective
platform design guide and chipset datasheet.
+If the pluggable board present state is S5, the transitions start as soon
as the PWRBTN# is pressed (but after the debounce logic), and does not
depend on when the Power Button is released.
+If pluggable board present state is S0-S4 and if PWRBTN# is held
low for at least four consecutive seconds, this will initiate unconditional
transition to S5 state.
Pluggable board detection. Output signal, recommend grounded on the
pluggable board side with pull up to +3.3V on the docking/control board
side.
High: No Pluggable
Low: Pluggable board Present
Consumer Electronics Control for Proof of Play/Display initiative. Can also
be used for display panel status detection and other control functions.
*Note that the OPS100-SH does not support the CEC function.
29
www.dfi.com
Chapter 5
50
SYS_FAN
O
System Fan: This signal shall be used to control the display panel system
fan.
Recommended pull up +3.3V on docking board side and routed to the
system fan control.
High: System Fan OFF
Low: System Fan ON
Note: This signal shall be triggered ON by the thermal management
system (EC) in the pluggable module only when needed.
Use case: In a situation where the display panel is in standby mode and
the Pluggable Module is still operating (e.g., remote maintenance etc),
the system fan solution may still be needed and since display panel is
in standby mode there is no way to control the system fan. This pin
therefore serves as an option to trigger the system fan to operate when
necessary.
RSVD
-
These pins are RESERVED for future expansion and shall be left as No
Connect(NC)
Reserved
41, 42, 43, 44,
45, 46, 47, 48,
49
30
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
The FX18-60S Connector (OPS100-SH)
95
GND
Ground
-
125
PCIE-TXN3
PCIe
OUT
The right angle mate plug connector (p/n: Hirose FX18-60S-0.8SH) should be mated with the
receptacle connector (p/n: Hirose FX18-60P-0.8SH); together, they provide interfacing for the
following functions:
94
PCIE-RXP3
PCIe
IN
124
GND
Ground
-
Power Contacts: 5V, 3V3@0.5A max
93
PCIE-RXN3
PCIe
IN
123
GND
Ground
-
Display Interface: 1*DisplayPort 1.2 (4K at 60Hz)
92
GND
Ground
-
122
PCIE-TXP2
PCIe
OUT
91
GND
Ground
-
121
PCIE-TXN2
PCIe
OUT
90
PCIE-RXP2
PCIe
IN
120
GND
Ground
-
89
PCIE-RXN2
PCIe
IN
119
GND
Ground
-
88
GND
Ground
-
118
PCIE-TXP1
PCIe
OUT
87
GND
Ground
-
117
PCIE-TXN1
PCIe
OUT
86
PCIE-RXP1
PCIe
IN
116
GND
Ground
-
85
PCIE-RXN1
PCIe
IN
115
GND
Ground
-
84
GND
Ground
-
114
PCIE-TXP0
PCIe
OUT
83
GND
Ground
-
113
PCIE-TXN0
PCIe
OUT
82
PCIE-RXP0
PCIe
IN
112
GND
Ground
-
81
PCIE-RXN0
PCIe
IN
111
PCI_E_WAKE
PHY Status
IN
PCI Express Expansion: 1*PCI-Express 3.0 x4
Control and Management Signals: 1*GPIO, 1*I2C, PHY device management signals
The following table lists the pin assignments of the 60-pin HRS connector:
Pins
Pin Assignment
Description
I/O
(1)
Pins
Pin Assignment
Description
I/O
110
DDI1_TXP0
140
Hot Plug - Hot
Plug Detect
109
DDI1_TXN0
139
DDI1_TXP2
108
GND
138
DDI1_TXN2
107
DDI1_TXP1
137
GND
106
DDI1_TXN1
136
DDI1_TXP3
105
GND
135
DDI1_TXN3
104
DDI_AUXP
134
GND
Ground
103
DDI_AUXN
133
GPIO
GPIO
102
GND
132
PCIe_RST
101
I2C1_DATA1
I2C Data
I/O
131
SLEEP_S3
PHY Status
OUT
100
I2C1_CLK
I2C Clock
OUT
130
LAN_DISABLE
PHY Status
OUT
99
GND
Ground
129
I2C_DATA_LAN
I2C/SMBus Data
I/O
98
PCIE_CLK_P
PCIe CLK
OUT
128
I2C_CLK_LAN
I2C/SMBus CLK
OUT
97
PCIE_CLK_N
PCIe CLK
OUT
127
GND
Ground
-
96
GND
Ground
126
PCIE-TXP3
PCIe
OUT
Ground
Ground
Ground
-
Notes:
(1) The I/O column definition is in reference to the OPS+ pluggable board.
(2) OC= Open Collector.
31
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 5
Signal Description
Here is the detailed description of each signal passing through the FX18-60S connector.
Pin No.
Signal
I/O
Description
Display Interface
140
DDP_HPD
139
DDI1_TXP2
138
I
Display Port Hot Plug Detect. Active High
DDI1_TXP3
135
DDI1_TXN3
110
DDI1_TXP0
109
107
106
PCIE-RXP3
I
93
PCIE-RXN3
I
90
PCIE-RXP2
I
89
PCIE-RXN2
I
86
PCIE-RXP1
I
85
PCIE-RXN1
I
82
PCIE-RXP0
I
81
PCIE-RXN0
I
PCI Express Differential Receive Pair Signals
I2C/GPIO interface (5pins – 2 used for LAN Control)
Display Port Data Channels
DDI1_TXN2
136
94
133
GPIO
I/O
General purpose Input Output, 3.3V
129
I2C_DATA_LAN
I/O
System Management Data Link to external PHY
128
I2C_CLK_LAN
I/O
System Management Clock Link to external PHY
101
I2C1_DATA1
I/O
I2C bus data
100
I2C1_CLK
O
I2C bus clock
LAN Control Interface (5 pins)
130
LAN_DISABLE
O
DDI1_TXN0
129
I2C2_DATA_LAN
I/O
It should be connected to LAN_DISABLE_N on the PHY. PCH will drive
it low to put the PHY into a low power state when functionality is not
needed.
System Management (I2C/SMBus) Data Link to external PHY
DDI1_TXP1
128
I2C2_CLK_LAN
I/O
System Management (I2C/SMBus) Clock link to external PHY
DDI1_TXN1
131
SLEEP_S3
O
111
PCIE_WAKE
I
104
DDI_AUXP
103
DDI_AUXN
Display Port Auxiliary Channel
LAN sub-system sleep control. When it is deasserted it indicates that the
PHY device must be powered. When it is asserted, power can be shut off
to the PHY device.
Wake Indicator from PCI-E PHY Device
PCIe Interface
132
PCIe_RST
I
126
PCIE-TXP3
O
125
PCIE-TXN3
O
122
PCIE-TXP2
O
121
PCIE-TXN2
O
118
PCIE-TXP1
O
117
PCIE-TXN1
O
110
PCIE-TXP0
O
109
PCIE-TXN0
O
111
PCI_E_WAKE
I
Wake Indicator from PCI-E PHY Device
96
PCIE_CLK_P
O
97
PCIE_CLK_N
O
100-MHz PCIe 3.0 specification compliant differential output clocks to
PCIe devices
PCI Express Differential Transmit Pair Signals
32
2 Ports
Hardware
Installation
Chapter 5
and Connectors
www.dfi.com
Chapter 6
Chapter 6 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the highlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup Defaults
<F10>
Save and Exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, repeatedly press “Delete” to enter the setup utility. If the message disappears before
you respond, restart the system or press the “Reset” button. You may also restart the system
by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
33
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23.
Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January
to December. Date displays the date, from 1 to 31. Year displays the year, from 1980 to
2099.
34
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
ACPI Settings
CPU Configuration
This section configures system ACPI parameters.
This section configures the CPU.
Wake on LAN
Intel® SpeedStep™
Enable or disable WOL (wake-on-LAN) to wake the system through the Ethernet adapter.
Enable or disable the Enhanced Intel SpeedStep® Technology, which helps optimize the
balance between system’s power consumption and performance. After it is enabled in
the BIOS, you can take advantage of its offering by setting power schemes from the
operating system’s power options.
State After G3
This field is to specify which state the system should be in when power is reapplied after a power failure (G3, the mechanical-off, state).
Always On The system is powered on.
Always Off The system is powered off.
Turbo Mode
BGRT Logo
CPU C States
Enable or disable the display of an operating system logo or image during boot
using the BGRT (Boot Graphics Resource Table) mechanism.
Enable or disable CPU Power Management. It allows the CPU to go to C states when it’s
not 100% utilized.
Enable or disable processor turbo mode, which allows the processor core to automatically run faster than the base frequency by taking advantage of thermal and power
headroom. Note this option is not available on the Core™ i3 processor.
Wake on RTC
Hyper-Threading
Automatically power the system on at a particular time every day from the
Real-time clock battery. Specify the wake up time of the day below: <hour>,
<minute>, <second>.
Enable Intel® Hyper-Threading Technology (HT) on the processor to improve performance of operating systems and software that are optimized for hyper-threading
technology. Please check the software specifications to determine if enabling HT can be
advantageous to the overall system performance.
35
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Intel® Trusted Execution Technology
Video Configuration
Enable Trusted Execution Technology on the processor to defend against malicious attacks by
validating the integrity of the system. Note that the default setting is disabled. Before you enable this feature, please enable and provision the TPM first. For more information, please contact
technical support. Note this option is only available for the Xeon® processor.
This section configures the video settings. Note that the configuration options may vary depending on the “Boot type” selected in the “Boot” menu.
SW Guard Extensions (SGX)
Enable Intel® SW Guard Extensions (SGX) on the processor to help protect application IP and
data. Alternatively, select “Software Controlled” to enable or disable this feature by individual
software program. Intel SGX is a set of new CPU instructions that can be used by applications to
set aside private regions of code and data. Note this option is only available for the Xeon® processor.
BIOS Guard
Enable BIOS Guard to guard against BIOS recovery attacks and ensure that updates to the BIOS
and Embedded Controller are authenticated and secure. Note this option is only available for the
Xeon® processor.
Primary Display
Select the primary display for the system. The options are Auto or IGFX (internal graphics). The order of video device initialization will be as follows:
Auto mode: PEG (PCIe Graphics devices connected to PEG lanes directly routed from
the CPU )->PCIe graphics devices->PCI graphics devices->IGFX (internal graphics)
IGFX: IGFX (internal graphics)->PEG (PCIe Graphics devices connected to PEG lanes directly routed from the CPU)->PCIe graphics devices->PCI graphics devices
Note that this option is only shown if the “Boot type” is set to “Dual” or
“UEFI”.
Internal Graphics Device
Enable, disable or automatically detect the internal graphics.
36
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Boot display
Audio Configuration
Prioritize device combination for display during system boot. Note that this option will be
shown only if the “Boot type” is set to “Dual” or “Legacy”.
This section configures the audio settings.
HDMI-in
Enable the HDMI-in option to let the HDMI signal pass through the system by connecting an HDMI-compliant source device to the front HDMI-in port. The default is disabled.
HD Audio
Control the detection of the high-definition audio devices.
Disabled
High-definition audio devices will be unconditionally disabled.
Enabled
High-definition audio devices will be unconditionally enabled.
Auto
High-definition audio devices will be enabled if present and disabled otherwise.
37
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
SATA Configuration
USB Configuration
This section configures SATA controllers.
This section configures the parameters of the USB devices.
SATA Controller(s)
Legacy USB Support
Enable or disable Serial ATA controllers.
Disabled
Disable USB keyboard/mouse/storage support.
Enabled
Enable USB keyboard/mouse/storage support.
UEFI Only
Enable USB keyboard/mouse/storage support only under UEFI environment.
SATA Speed
Select Serial ATA device speed. The options are Gen1 (1.5 Gbit/s), Gen2 (3 Gbit/s),
Gen3 (6 Gbit/s) or auto.
Serial ATA Port 2 Hot Plug
Enable or disable each Serial ATA port and its hot plug function. Note this SATA port
controls the SATA signal of the M.2 Type 2280 connector on the system board. Therefore, if a PCIe NVMe SSD is used instead of an mSATA SSD, this option will not be
shown.
XHCI Hand-off
Enable this item for operating systems that do not support xHCI Hand-off. The XHCI
ownership change will be claimed by the XHCI driver.
38
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
PCI Express Configuration
This section configures the settings of PCI Express root ports.
PCI Express Configuration
PCIE1 (denotes the PCIe x4 slot on the Docking Board) /Intel LAN I219-LM/
Intel WLAN AC8260 (pre-installed on the M.2 Type 2230 connector)/PCIE
SSD (denotes the M.2 Type 2280 connector)
Select a PCI Express root port and press “Enter” to configure.
For each PCIe root port, configure the following parameters:
Enable/Disable
Enable or disable this PCI Express root port.
PCIe Speed
Select the speed of the PCI Express root port: Auto, Gen1 (2.5 GT/s), Gen2 (5 GT/s) or
Gen3 (8 GT/s).
Hot Plug
Enable or disable the hot plug function of the PCIe root port.
39
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
ME Configuration
Active Management Technology Support
This section configures flashing of the Intel® Management Engine.
The section allows you to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Refer to Chapter 8 - Intel AMT Settings for more information. Note that
this function is not available for the Intel® Core™ i3 processor.
Me Fw Image Re-Flash
Enable or disable Intel® Management Engine firmware flashing when updating the BIOS.
Intel AMT Support
Enable or disable Intel® Active Management Technology BIOS extension.
Un-Configure ME
Clears all ME related configurations without requiring a password on the next boot.
40
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Debug Configuration
Device Manager
This section configures the debug function.
This Device Manager menu is used to configure UEFI network settings when the “Network Stack” is enabled in the “Dual” or “UEFI” boot mode. Refer to the “Boot” section in
this chapter. To access this menu, go to “Advanced”>”Device Manager”. The screen will
warn you that you are going to exit the BIOS setup utility.
Dynamic EFI Debug
Enable or disable output of the log messages for debugging through a serial port.
If you select to enable this function, please set a serial port for this purpose with the
following parameters:
EFI debug print level
Enter or choose the desired print level for displaying different type of log messages. The
options are as follows:
0x00000001: Display messages of system initialization
0x00000002: Display warning messages
0x00000004: Display messages of Load events
0x00000008: Display messages of EFI File system
0x00000040: Display informational debug messages
0x80000000: Display Error messages
0x8000004F: Display all types of messages shown above (This is the default.)
EFI Debug serial port
Enter or choose the serial port number for message output. The options are COM1 (0x3F8)/
COM2 (0x2F8). The default is 0x3F8.
EFI Debug baud rate
Enter or choose the baud rate for serial communication. The default is 115200.
41
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Network Device List
Port Configuration Menu
The "Device Manager” screen is displayed. And if the “Network Stack” or the “PXE Boot
to LAN” option is enabled from the “Boot” menu, the “Network Device List” should
be shown in the “Device list”. Select “Network Device List” to view all of the detected
network devices. For each network device, you can select to view and configure its
settings. In addition, you can select either the IPv4 or IPv6 network settings for UEFI
network configurations.
This screen shows hardware information for the Ethernet controllers and configures
their operation.
Blink LEDs
Enter the duration (seconds) for the Ethernet’s ACT LED to blink to indicate its presence.
NIC Configuration
This screen configures the Ethernet controller. Select the link speed from the following
options: Auto Negotiated, 10Mbps Half, 10Mbps Full, 100Mbps Half, and 100Mbps Full.
42
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
IPv4 Network Configuration
IPv6 Network Configuration
This screen configures the IP addressing method (DHCP or static IP). For static IP addressing, configure the following:
Local IP address and subnet mask: Enter the IP address for the network device in the
IPv4 format:
x . x . x . x (x must be a decimal value between 0 and 255).
If you select to use IPv6 network settings, enter the Interface ID (64 bit).
Policy: Select either automatic or manual. And select "Advanced Configuration" to
configure IPv6 network address manually if the manual option is selected.
New IPv6 address: Enter the IP address for the network device in the IPv6 format:
x : x : x : x : x : x : x : x (x can be any hexadecimal value between 0 and FFFF). Place a
space to separate each IP address to enter more than one address.
New Gateway addresses: Enter gateway addresses in the IPv6 format.
New DNS addresses: Enter DNS (Domain Name System) server IP addresses in the IPv6
format.
Local Gateway: Enter the gateway address in the IPv4 format.
Local DNS (Domain Name System) Servers: Enter DNS (Domain Name System) server IP
addresses in the IPv4 format.
43
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Super IO Configuration
PC Health Status
This section configures the system super I/O chip parameters.
This section displays PC health information such as the voltages and CPU and system temperatures.
Serial Port A and Serial Port B
Enable or disable each serial port.
Disable Disable this serial port.
Enable
Enable this serial port.
It also shows the Base I/O address and the assigned interrupt number.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable
WDT. Input any value between 1 and 255.
CPU Smart Fan Control
Enable the CPU smart fan control to let the system dynamically adjust fan speeds according to CPU temperatures.
44
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Console Redirection
COMA/COMB/PCI Serial Port
Enable or disable the serial redirection function for each of the detected serial ports on
the system. And configure the serial communication parameters to be used between the
system and a remote station. Alternatively, choose to use the pre-configured global settings from the previous menu.
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
Console Serial Redirect
Enable or disable the console redirection function. (The default is disabled.) If you select
to enable it, please configure the following parameters for serial communication between
the system and a remote station:
Terminal type: VT_100, VT_100+, VT_UTF8, or PC_ANSI.
Baud rate: 115200, 57600, 38400, 19200, 9600, 4800, 2400 or 1200.
Data bits: 8 bits or 7 bits.
Parity: None, Even or Odd.
Stop bits: 1 bit or 2 bits.
Flow control: None, RTS/CTS or XON/XOFF
This is the global setting for all of the designated serial ports for the console redirection
function.
45
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
MEBX Configuration
The Manageability Engine BIOS Extension (MEBx) Setup allows you to set up Intel® Active
Management Technology (Intel® AMT). For more information, please refer to Chapter 8.
46
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Security
This section configures the Trusted Platform Module (TPM) function.
TPM Availability
Set Supervisor Password
Show or hide TPM availability and its configurations.
Set the administrative password for entering the BIOS utility or upon entering the
power-on self-test (POST) process. The length of the password must be greater than 1
character and less than or equal to 10 characters.
TPM Operation
Enable or disable the TPM function. It displays the following options:
• No Operation: No changes to the current state.
• Disable: Disable and deactivate TPM.
• Enable: Enable and activate TPM.
Power-on Password
If you select to set the supervisor password, this option will be shown. Enable or disable
prompt for password at boot.
Clear TPM
Remove all TPM ownership contents.
Note:
To enable the Intel® TXT function on the system, please enable the activate the
TPM function first.
47
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Boot
Boot Device Priority
This section configures boot options.
This section configures legacy or EFI boot order or both depending on the “Boot
Type” selected.
Numlock
Select the power-on state for the Num Lock key.
EFI Boot Menu
Use + and - keys to arrange the priority of the boot devices in the list.
Boot Type
Select the boot type. The options are Dual Boot, Legacy Boot and UEFI Boot Type.
Legacy Boot Menu
Network Stack
This option is shown only when the boot type is set to Dual or UEFI.
Enable or disable UEFI network stack. It supports the operation of these functions
or software: Windows 8 BitLocker Network Unlock, UEFI IPv4/IPv6 PXE and legacy
PXE option ROM.
If this function is enabled, you can then go to “Advanced”>”Device Manager” to
configure network settings for network connection under the UEFI environment.
Normal
For this option, determine the boot order for the devices within each category. Use the
+ and - key to arrange the priority of the boot devices in the list. The first device in the
list has the highest boot priority.
Advance
For this option, determine the boot order for all bootable devices. Use + and - keys to
arrange the priority of the detected boot devices in the list. The first device in the list
has the highest boot priority.
PXE Boot to LAN
Enable or disable Preboot eXecution Environment (PXE) boot to LAN. In the UEFI
or Dual boot mode, this function can only be enabled if the Network Stack support
is enabled.
USB Boot
Enable or disable booting to USB boot devices.
Chapter 6 BIOS Setup
48
www.dfi.com
Chapter 6
Exit
This section configures the parameters for exiting the BIOS setup utility.
Exit Saving Changes
Select this field and press <Enter> to exit BIOS setup and save your changes.
Load Optimal Defaults
Select this field and press <Enter> to load the optimal defaults.
Discard Changes
Select this field and press <Enter>to exit the BIOS setup without saving your changes.
Save Setting to file
Select this option to save BIOS configuration settings to a USB drive. The operation will
fail if there aren’t any USB devices detected on the system. The saved configuration will
have the DSF file extension and can be used for restoration.
Restore Setting from file
Select this option to restore BIOS configuration settings from a USB drive. Note that this
option will not be available if there aren’t any USB devices detected on the system.
49
Chapter 6 BIOS Setup
www.dfi.com
Chapter 6
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need an updated BIOS file and a flash utility. Please contact
technical support or your sales representative for the files and specific instructions on how to
update BIOS with the flash utility.
1. The Intel® Management Engine has already been integrated into this system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing the BIOS update procedure. For your convenience,
we will also provide you with an auto-execution file in the BIOS file downloaded. This autoexecution file will bring you directly to the flash utility menu soon after system boots up and
finishes running the boot files in your boot disk.
RRead file successfully.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
(path= “platform.ini”)
Information
Please do not remove the AC power
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2017, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: OPS100-SH
New BIOS Model name: OPS100-SH
Current BIOS version: B176.06A
New BIOS version: B176.06A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\OPS100-SH>_
100%
100%
50
Chapter 6 BIOS Setup
www.dfi.com
Chapter 7
Chapter 7 - Supported Software
For Windows 8.1
The DVD that came with the system board contains drivers, utilities and software applications
required to enhance the performance of the system board.
Insert the DVD into a DVD-ROM drive. The auto-run screen will appear. If the “Autorun” does not
automatically start, please go directly to the root directory of the DVD and double-click “Setup”.
For Windows 10
51
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Intel Chipset Software Installation Utility
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
Please wait while the installation is in progress.
The Intel Chipset Software Installation Utility is used for updating Windows® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utility, follow these steps:
1. Setup is ready to install the
utility. Click “Next”.
4. Please wait while the installation is in progress.
2. Read the license agreement,
and then click “Yes”.
5. Click “Restart Now” to allow
the new software installation to take effect.
52
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Intel Graphics Drivers
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
To install the driver, click “Intel Graphics Drivers” in the main menu.
1. Setup is now ready to
install the graphics driver.
Click “Next”.
4. Setup is now installing the
driver. Click “Next” to continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme”
is enabled. With this is enabled and after the system is rebooted, the screen will turn
blank for 1 to 2 minutes (while WinSAT is running) before the Windows 7/ Windows 8.1/
Windows 10 desktop appears. The “blank screen” period is the time Windows is testing the
graphics performance.
We recommend that you skip this process by disabling this function and then click “Next”.
2. Read the license agreement, and then click “Yes”.
5. Click “Yes, I want to restart
this computer now”, and
then click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
53
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Intel LAN Drivers
4. Click “Install” to begin the
installation.
To install the driver, click “Intel LAN Drivers” in the main menu.
1. Setup is preparing to install
the driver. Click “Next” to
continue.
5. After the installation is
complete, click “Finish”.
2. Click “I accept the terms in
the license agreement” if
you accept the agreement,
and then click “Next”.
3. Select the program features
you want installed, and
then click “Next”.
54
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Intel Management Engine Drivers
3. Setup is currently installing
the driver. After the installation is complete, click “Next”.
To install the driver, click “Intel ME Drivers” in the main menu.
1. Setup is ready to install
the driver. Click “Next”
to continue.
4. Please wait while the product is being installed.
2. Read the license agreement, and then click “Next”.
5. After the installation is
complete, click “Finish”.
55
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Intel USB 3.0 Drivers (for Windows 8.1)
3. Go through the readme document for more installation tips,
and then click “Next”.
To install the driver, click “Intel USB3.0 Drivers” in the main menu.
1. Setup is ready to install the driver.
Click “Next” to continue.
4. Setup is currently installing the
driver. After the installation is
complete, click “Next”.
2. Read the license agreement, and
then click “Yes”.
5. After the installation is complete,
click “Finish”.
56
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Audio Drivers
Serial IO Drivers
To install the driver, click “Realtek Audio Drivers” on the main menu:
To install the driver, click “Intel Serial IO Drivers” in the main menu.
1. Setup is ready to install the driver.
Click “Next” to continue.
1. Setup is now ready to install the
audio driver. Click “Next”.
2. Follow the rest of the steps on
the screen; click “Next” each
time you finish a step.
2. Read the license agreement carefully.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement and then
click “Next”.
3. Click “Yes, I want to restart my
computer now”, and then click
“Finish”.
Restart the system to allow the new
software installation to take effect.
57
Chapter 7 Supported Software
www.dfi.com
Chapter 7
3. Read the file information and then
click “Next”.
5. Setup is now installing the driver.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
6. Click “Finish” to exit the setup.
58
Chapter 7 Supported Software
www.dfi.com
Chapter 7
Wi-Fi/Bluetooth
2. Click “Finish” to exit the setup.
To install Wi-Fi drivers, click “WiFi” in the main menu.
The Intel PROSet/Wireless Software Setup screen will be displayed.
1. Read the End User License Agreement carefully.
Click the box if you agree with the
terms in the agreement and then
click “install” to install with default
settings or “Customize” to install with
selected features.
To install Bluetooth drivers, click “Bluetooth ” in the main menu. The Intel PROSet/
Wireless Tools Installation Wizard will start. Please follow the on-screen instructions to
complete the installation.
2. Setup is now installing the driver.
59
Chapter 7 Supported Software
www.dfi.com
Chapter 86
Chapter
Chapter 8 - Intel AMT Settings
Enable Intel® AMT in the BIOS
Overview
1. Power on the system then press <Del> to enter the main menu of the BIOS setup utility.
Intel Active Management Technology (Intel® AMT) combines hardware and software solutions
to provide maximum system defense and protection to networked systems. Note that the SKU
with the Intel® Core™ i3 processor does not support iAMT.
2. In the “Advanced” menu, select “Active Management Technology Support”.
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
• Discover
Allows remote access and management of networked systems even while PCs are powered off,
significantly reducing desk-side visits.
• Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
3. In the “Active Management Technology Support” menu, select “Enabled” for “Intel AMT
Support”.
60
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
Set up Intel® AMT using the Intel® Management
Engine BIOS Extension (MEBX)
4. In the “Exit” menu, select “Exit Saving Changes”, and then select “OK”.
1. After the system reboots, press <Del> to enter the BIOS menu again.
2. In the “Advanced” menu, select “MEBX Configuration” to enter the Manageability Engine
BIOS Extension (MEBx) Setup.
3. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password,
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
61
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
4. Enter a password in the space provided under “Intel(R) ME Password”, and then press
“Enter”. The password must include:
•
•
•
•
•
5. You will be asked to verify the password. Enter the same new password in the space provided under “Verify Password”, and then press “Enter”.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Enter] = Select Entry
[Esc]= Exit
6. Select “Intel(R) ME General Settings” and press “Enter”.
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
62
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
7. Select “Change Intel(R) ME Password” and press “Enter”.
8.Select “Local FW Update” and press “Enter”. Select “Enabled”, “Disabled” or “Password
Protected”, and then press “Enter”.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under “Intel(R) ME New Password”, and then press “Enter”.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
Disabled
Enabled
Password Protected
<Enabled>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9. Select Previous Menu until you return to the “Main Menu”. Select “Intel(R) AMT Configuration” and press “Enter”.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
[Esc]= Exit
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
63
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
10. In the “Intel(R) AMT Configuration” menu, select “Manageability Feature Selection” and
then press “Enter”. Select “Enabled” or “Disabled”, and then press “Enter”.
12. In the “SOL/Storage Redirection/KVM” menu, select “Username and Password” and then
press “Enter”. Select “Enabled” or “Disabled”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved..
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
11. In the “Intel(R) AMT Configuration” menu, select “SOL/Storage Redirection/KVM” and
press “Enter”.
13. In the “SOL/Storage Redirection/KVM” menu, select “SOL” and then press “Enter”. Select
“Enabled” or “Disabled”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
sion>
> Remote Setup And Configuration
> Power Control
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
< Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Anytime>
<Full Unprovi-
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
64
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
14. In the “SOL/Storage Redirection/KVM” menu, select “Storage Redirection” and then press
“Enter”. Select “Enabled” or “Disabled”, and then press “Enter”.
16. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“User Consent” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
User Opt-in
Opt-in Configurable from Remote IT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< KVM>
< Enabled>
Disabled
Enabled
Configure When User Consent Should be Required.
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
15. In the “SOL/IDER/KVM” menu, select “KVM Feature Selection” and then press “Enter”.
Select “Enabled” or “Disabled”, and then press “Enter”.
[Esc]= Exit
17. In the “User Consent” menu, select “User Opt-in” and then press “Enter”. Select “None”
or “KVM” or “ALL”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
65
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
20. In the “Intel(R) AMT Configuration” menu, select “Network Setup”, and then press “Enter”.
18. In the “User Consent” menu, select “Opt-in Configurable from Remote IT” and then press
“Enter”. Select “Enabled” or “Disable Remote Control of KVM Opt-in Policy”, and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< ALL>
< Enabled>
Disabled
Enabled
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
21. In the “Intel(R) ME Network Setup” menu, select “Intel(R) ME Network Name Settings”,
and then press “Enter”.
19. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“Password Policy”, and then press “Enter”.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Intel (R) ME Network Name Settings
> TCP/ IP Settings
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Stepup And Configuration
Anytime
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Enter] = Select Entry
[Esc]= Exit
66
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
22. In the “Intel(R) ME Network Name Settings” menu, select “Host Name”, and then press
“Enter”. Enter the computer’s host name and press “Enter”.
24. Select “Shared/Dedicated FQDN” and then press “Enter”. Select “Shared” or “Dedicated”,
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Host Name
[Enter] = Complete Entry
Dedicated
Shared
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc]= Discard Changes
23. Select “Domain Name” and then press “Enter”. Enter the computer’s domain name, and
then press “Enter”.
25. Select “Dynamic DNS Update” and then press “Enter”. Select “Enabled” or “Disabled”, and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Domain Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
_
_
<Shared>
<Disabled>
Disabled
Enabled
[Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
67
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
26. Select Previous Menu until you return to the “Intel(R) ME Network Setup” menu. Select
“TCP/IP Settings” and press “Enter”.
28. In the “Intel(R) AMT Configuration” menu, select “Activate Network Access”, and then
select “Yes/No” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
TCP/ IP SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Wired LAN IPV4 Configuration
[↑↓] = Move Highlight
[Enter] = Select Entry
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Activates the current network settings
and opens the ME network interface
Continue: (Y/N)
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
[Esc]= Exit
27. In the “TCP/IP Settings” menu, select “Wired LAN IPV4 Configuration”, and then press
“Enter”.
29. In the “Intel(R) AMT Configuration” menu, select “Unconfigure Network Access”, and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
<Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
Disabled
Enabled
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<During Setup And
Configuration>
<Full Unprovision>
Full Unprovision
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
68
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
30. In the “Intel(R) AMT Configuration” menu, select “Remote Setup And Configuration”, and
then press “Enter”.
32. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning Record”,
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
< Enabled>
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
<Anytime>
<Full Unprovision>
Provision Record is not present
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
31. In the “Intel(R) Remote Setup And Configuration” menu, select “Current Provisioning
Mode”, and then press “Enter”.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
[Enter] = Select Entry
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Provisioning Mode: PKI
[↑↓] = Move Highlight
[Enter] = Select Entry
33. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server IPV4/
IPV6”, enter “Provisioning server address” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Provisioning server address
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
69
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
34. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server
FQDN”, enter the FQDN of Provisioning server, and then press “Enter”.
36. In the “Intel(R) Remote Setup And Configuration” menu, select “TLS PKI”, and then press
“Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
35. In the “Intel(R) Remote Setup And Configuration” menu, select “RCFG” and press “Enter”,
and then select “Start Configuration Y/N” and press “enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
This will activate Remote Condiguration. Continue: (Y/N)
[Enter] = Select Entry
[Esc]= Exit
37. In the “Intel(R) Remote Configuration” menu, select “Remote Configuration**” and press
“Enter”, and then select “Enabled” or “Disabled” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
[↑↓] = Move Highlight
[Enter] = Select Entry
< Enabled>
_
Disabled
Enabled
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
70
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
40. In the “Intel(R) AMT Configuration” menu, select Power Control, and then press “Enter”.
38. Select “PKI DNS Suffix”, enter the “PKI DNS Suffix”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Hash Name
VeriSign Class 3
VeriSign Class 3
Go Daddy Class 2
Comodo AAA CA
Starfield Class 2
VeriSign Class 3
VeriSign Class 3
VeriSign Class 3
GTE CyberTrust G1
Baltimore Cyber Tr
Cyber Trust Global
Verizon Global Ro
Entrust. net CA (2
Entrust Root CA
VeriSign Universa
Go Daddy Root CA
Entrust Root CA Startfield Root CA
< Enabled>
_
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[Ins]= Add New Hash
[↑↓] =Move Highlight
39. Select “Manage Hashes” and press “Enter”, and then select one of the hash names.
INTEL (R) REMOTE CONFIGURATION
[↑↓] = Move Highlight
Algorithm
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
[+] = Activate Hash
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
< Enabled>
_
[Enter] = Select Entry
[Delete] = Delete Hash
[Enter] = View Hash
Default
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
41. In the “Intel(R) AMT Power Control” menu, select “Intel(R) AMT ON in Host Sleep States”
and then press “Enter”. Select an option and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Active
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<Anytime>
<Full Unprovision>
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
71
Chapter 8 Intel AMT Settings
www.dfi.com
Chapter 86
Chapter
44. Select Previous Menu until you return to the “Main Menu”. Select “Exit”, and then press
“Enter”. Type “Y” and press “Enter”.
42. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout”, and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
These configurations are effective only after AMT provisioning has started
Intel (R) AMT ON in Host Sleep States
<Desktop: ON in S0,
ME Wake in S3, S4-5>
Idle Timeout
65535
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Desktop : ON in S0
Desktop : ON in S0, ME Wake in S3, S4-5
Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
43. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout”, and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
<ENTER> = Complete Entry
[ESC]= Discard Changes
72
Chapter 8 Intel AMT Settings
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising