DFI | EC300/EC310/EC320/EC321/EC322 Installation Guide | manual | Dfi EC300/EC310/EC320/EC321/EC322 Installation Guide Manual

Dfi EC300/EC310/EC320/EC321/EC322 Installation Guide Manual
EC300/310/320/321/322 Series
Installation Guide
Package Contents






1 System unit
1 SATA data/power cable
1 120W power adapter (-CR6G60/-CRA060/-CR6881)
1 160W power adapter (-CR4866)
1 Installation Guide
1 CD disk includes:
- Drivers
- Manual
Optional Items
 1 Wallmount kit
 1 Power cord
 1 3G
System Models
Rear I/O Ports
DC-in power jack:
3-pole terminal block
Speaker-out:
2W 3.5mm audio jack
VGA: DB-15 D-sub
EC3xx- EC3xx- EC3xx- EC300/320/321/
CR6881 CR6G60 CRA060
322-CR4G65
EC3xx-CR4866
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DVI (DVI-D signal)
1
0
0
0
0
Gigabit LAN: RJ45 with LEDs
2
2
2
5
2
PoE Gigabit LAN: RJ45
0
0
0
0
6
6
4
4
4
4
COM: DB-9 D-sub
(RS232/422/485)
COM: 5-pole terminal block
(RS232/422/485)
USB 3.0 Type A
0
0
6
0
0
2
2
2
2
2
USB 2.0 Type A
2
0
0
0
0
8-bit
16-bit
0
16-bit
8-bit
Reset button
1
1
1
1
1
Power LED
1
1
1
1
1
HDD LED
1
1
1
1
1
1
EC300/321CR4G65
4
1
EC3xx-CR4866
GPIO: 9-pole terminal block
Alert LED
Front I/O Ports
USB 2.0 Type A
1
1
1
EC3xx- EC3xx- EC3xxCR6881 CR6G60 CRA060
4
4
4
(2 ports are RS232.)
4
Power button with indicator
1
1
1
1
1
Reset button
1
1
1
1
1
HDD LED
1
1
1
1
1
Alert LED
Wi-Fi module antenna hole
1
1
1
1
1
2
2
2
2
2
1
Installing a SATA Drive
1.
Locate the SATA drive bay on the cover.
Cover
SATA drive bay
2.
Remove the 4 mounting screws that secure the HDD brackets to the drive
bay.
Mounting screw
2
3.
Align the mounting holes of the SATA drive with the mounting holes on the
HDD bracket and then use the provided mounting screws to secure the drive in
place.
SATA drive
HDD bracket
Mounting screws
Mounting screw
4.
Place the SATA drive (with HDD bracket) into the cover. Align the mounting
holes on the HDD bracket with the mounting holes on the SATA drive bay and
then use the provided mounting screws to secure the drive in place.
Mounting hole
HDD bracket
3
Mounting hole
Mounting screw
5.
Connect A to the SATA power/data connector on the SATA drive, B and C to
the SATA power connector and SATA data connector respectively on the system
board.
SATA power connector (B)
SATA power/data
connector (A)
SATA data
connector (C)
4
SATA power/data
connector
SATA data
connector
SATA power connector
5
System Boards and Jumper Settings
System fan
Mini PCIe/mSATA
Power select (JP4)
1
1
CPU Fan
1
LED
DC-IN
USB 7
Mini PCIe
DDR3_2 SODIMM2
USB 6-7
power select
(JP2)
DDR3_1 SODIMM1
COM 1
COM1 RS232/422/485
select (JP11)
COM 2
12
COM1 RS232/Power
select (JP12)
12
11
10
3
2
1
5
6
1
10 9
USB 4
PS/2 power
select(JP1)
1
1
2 1
PS/2 KB/MS
COM2 RS232/
Power select
(JP14)
5
6
USB 5
2
Mini PCIe/mSATA
select (JP6)
COM2
RS232/422/485
select (JP13)
1
2
11
Front Panel
5
6
1
2
1
2
GV
A
VGA
1
5
6
1
2
USB 6
1
Chassis
intrusion
USB 4-5 power
select (JP3)
2nd level rear I/O
module connector
Factory Testing
(JP15)
1
USB 0-1 power
select (JP8)
1
SATA 0
1
HDD Power
1
1
1
SATA 1
USB 0-1
1
1
LED
LAN 1
Battery
Reset
SPI Flash
BIOS
Audio
CompactFlash
1
Power
Reset
Power-on
select (JP5)
Clear CMOS (JP7)
LAN 2
Riser card connector
Reset/Power on
select (JP10)
Clear CMOS Data
JP7
Power-on Select
Normal (default)
1-2 On
Power-on via power button (default)
1-2 On
Clear CMOS Data
2-3 On
Power-on via AC power
2-3 On
PS/2 Power
JP1
JP5
USB Power: 0-1 (JP8), 4-5 (JP3), 6-7 (JP2)
+5V (default)
1-2 On
+5V (default)
1-2 On
+5V_standby
2-3 On
+5V_standby
2-3 On
COM1 (JP12), COM2 (JP14) RS232/Power
RS232 (default)
RS232 with power
Mini PCIe/mSATA
Power Select
1-3, 2-4 On
3-5 (+12V),
4-6 (+5V) On
JP4
3V3 (default)
1-2 On
3VDU
2-3 On
Reset/ Power on Select
COM1 (JP11), COM2 (JP13) RS232/RS422/RS485
Select
RS232 (default)
1-2 On
RS422 Full Duplex
3-4 On
RS485
5-6 On
Mini PCIe/mSATA Select
JP6
Mini PCIe (default)
1-2, 4-5, 7-8, 10-11 On
mSATA
2-3, 5-6, 8-9, 12-13 On
JP10
Reset (default)
1-2 On
Power on
2-3 On
Note: The Reset/ Power on Select is used to select
the function of the reset bottom.
6
934-EC3000-1A0G
A22133525
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising