DFI | Q7X-151(R.D1) | manual | Dfi Q7X-151(R.D1) Manual

Dfi Q7X-151(R.D1) Manual
Q7X-151 (R.D1)
Qseven Carrier Board
User’s Manual
A54900939
Q7X-151 (R.D1)
www.dfi.com
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
© 2019. All Rights Reserved.
Notice:
Trademarks
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2
Q7X-151 (R.D1)
www.dfi.com
Table of Contents
Front Panel ..................................................................................18
Cooling Fan Connectors.................................................................19
CAN-Bus Connector.......................................................................19
LVDS LCD Panel Connector............................................................20
SATA (Serial ATA) Connector..........................................................21
SATA (Serial ATA) Power Connector................................................21
LPC Debug Connector....................................................................22
I2C Connector...............................................................................22
Expansion Slots.............................................................................23
Switches.......................................................................................25
LEDs.............................................................................................25
Battery.........................................................................................26
MXM Connector.............................................................................26
Copyright���������������������������������������������������������������������������������������������������������������..2
Trademarks�������������������������������������������������������������������������������������������������������������2
FCC and DOC Statement on Class B��������������������������������������������������������������������2
About this Manual��������������������������������������������������������������������������������������������������4
Warranty ����������������������������������������������������������������������������������������������������������������4
Static Electricity Precautions���������������������������������������������������������������������������������4
Safety Measures�����������������������������������������������������������������������������������������������������4
About the Package�������������������������������������������������������������������������������������������������5
Chapter 1 - Introduction���������������������������������������������������������������������������������������6
Specifications....................................................................................................6
Chapter 3 - Supported Software ����������������������������������������������������������������������� 28
Chapter 2 - Hardware Installation ����������������������������������������������������������� 7
Realtek Audio Drivers..................................................................................... 28
Adobe Acrobat Reader 9.3............................................................................ 29
Board Layout.....................................................................................................7
Mechanical Diagram......................................................................................... 8
Jumper Settings................................................................................................8
Clear CMOS Data............................................................................8
USB Power Select............................................................................9
USB Signal Select............................................................................9
Panel Power Select........................................................................10
Backlight Power Select...................................................................10
LCD/Inverter Power Select.............................................................11
Dimming Mode Select....................................................................11
BIOS Boot Select...........................................................................12
ATX/AT Power Select.....................................................................12
LPC/GPIO Switch...........................................................................13
High/low Switch for MXM Pin 27....................................................13
Panel I/O Ports............................................................................................... 14
Rear Panel I/O Ports.....................................................................14
Front Panel I/O Ports....................................................................14
12V DC-in.....................................................................................14
RJ45 LAN Port...............................................................................15
DisplayPort....................................................................................15
USB Ports.....................................................................................16
Audio............................................................................................17
Internal I/O Connectors................................................................................. 18
SMBus Connector..........................................................................18
3
Q7X-151 (R.D1)
www.dfi.com
About this Manual
Static Electricity Precautions
This manual can be downloaded from the website, or acquired as an electronic file included in
the optional CD/DVD. The manual is subject to change and update without notice, and may be
based on editions that do not resemble your actual products. Please visit our website or contact our sales representatives for the latest editions.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other
components. Perform the upgrade instruction procedures described at an ESD
workstation only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
Safety Measures
To
•
To
•
4
avoid damage to the system:
Use the correct AC input voltage range.
reduce the risk of electric shock:
Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Q7X-151 (R.D1)
www.dfi.com
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
•
•
One Q7X-151 (R.D1) board
One Serial ATA cable
Optional Items
•
•
•
USB port cable
I/O shield
Power adapter (100W, 12V)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• A CPU
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1 - Introduction
Q7X-151 (R.D1)
www.dfi.com
Chapter 1 - Introduction
► Specifications
Graphics
• Display ports
- 1 dual channel LVDS
- 1 eDP port
- 2 DP port
Audio
• Realtek ALC886 5.1-channel High Definition Audio
• Audio outputs: Mic-in/Center+Subwoofer, Line-in/Surround and Line-out
USB
• 3 USB 3.0 and 8 USB 2.0 ports
Storage
• 2 SATA 3.0 port with data transfer rate up to 6Gb/s
- SATA port provides adequate space for SATA DOM
Fron Pane I/O
• 1 DP port
Rear Panel I/O
•
•
•
•
•
•
•
1 12V DC-in jack
2 DB-9 RS232 serial ports
1 DP port
1 RJ45 LAN port
3 USB 3.0 port
6 USB 2.0 type A ports
Mic-in/Center+Subwoofer, line-in/surround and line out jacks
I/O Connectors • 1 connector for 2 external USB 2.0 ports
• 2 UART ports
- 1 supports TX/RX signal only (UART 2)
• 1 eDP port
• 1 LVDS LCD panel connector
• 1 LCD/inverter power connector
• 2 SATA power connector
• 2 SATA 3.0 port
• 1 LPC connector
• 1 I2C connector
• 1 SMBus connector
• 1 CAN-bus connector
• 1 front panel connector
• 3 fan connectors
6
Expansion Slots
• 2 PCIe x1 slot
• 2 Mini PCIe slot
• 1 SDIO socket
WatchDog Timer
• Watchdog timeout programmable via software from 1 to 255 seconds
Damage Free
Intelligence
• Monitors system temperature and overheat alarm
• Monitors system fan speed and failure alarm
ROM Interface
• 1 SPI interface
- Supports up to 64Mbit
Temperature
• Operating: 0oC to 60oC
• Storage: -20oC to 85oC
Humidity
• 5% to 90%
Board to Board
Connector
• One MXM connector
• Support Qseven R2.1
Dimensions
• Mini-ITX form factor
• 170mm (6.7") x 170mm (6.7")
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
Chapter 2 - Hardware Installation
►►Board Layout
Battery
COM 1
1
DC-in
9
System Fan 1
2
1
2
1
7
1
1
Buzzer
JP24
SPI Programming
JP2
2
LPC
Debug LED
14
13
1
2
JP21
LVDS
LCD Panel
5
JP12
1
40
eDP
6
1
JP1
2
1
SPI Flash BIOS
USB 1 (USB 3.0)
USB 2/3 (USB 2.0)
19
JP9
1
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in boards, and other components.
Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide
some ESD protection by wearing an antistatic wrist strap
and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact
with the system chassis throughout any procedures requiring ESD protection.
DIO
2 1
1
1
39
DP 1
1
2
5
6
JP11
40
JP16
1
MXM
1
LAN
USB 0/2 (USB 3.0)
USB 0/1 (USB 2.0)
LCD/Inverter
Power
1
5
SATA 0
1
5
1
2
SMBus
4
SATA 1
1
SATA
Power 0
1
Line-in
Line-out
Mic-in
4
1
SATA
Power 1
GPO LED
JP3
1
Mini PCIe 2
USB 4/5
(USB 2.0)
1
JP4
1
1
J9
PCIe 1 (PCIe x1)
1
1
JP5
USB 6/7
(USB 2.0)
9
1
10
2
Sleep
PCIe 2 (PCIe x1)
Front
Panel
JP10
1
Lid
Realtek
ALC888
DP 2
Thermal Trip LED
Mini PCIe 1
JP23
CAN Bus
JP25
1
2
2
1
I2C
JP17
1
Reset
Power
1
2
11
12
SD card (Bottom Side)
7
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►►Mechanical Diagram
www.dfi.com
►►Jumper Settings
Clear CMOS
154.94
46.23
22.86
JP9
157.48
151.76
124.83
114.95
94.89
73.83
If any anomaly of the followings is encountered —
53.45
a) CMOS data is corrupted;
39.79
b) you forgot the supervisor or user password;
35.19
c) failure to start the system due to BIOS mis-configuration
21.23
0.00
— it is suggested that the system be reconfigured with default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
1. Power-off the system and unplug the power cord.
2. Put a jumper cap on JP9’s pin 2 and pin 3. Wait for a few seconds and set JP9 back to
its default setting, i.e. jumper cap on pin 1 and pin 2.
154.94
0.00
6.35
46.78
53.34
10.19
0.00
1.73
3. Plug the power cord and power-on the system.
3
2
1
▲▲ 1-2 On: Normal (default)
8
3
2
1
▲▲ 2-3 On: Clear CMOS
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Jumper Settings
►► Jumper Settings
USB Power Select
USB Signal Select
www.dfi.com
JP2
JP1
A
B
JP3
JP23
JP10
JP1 (for rear I/O USB 0/1), JP2 (for rear I/O USB 2/3), JP23 (for rear I/O USB 4/5), and JP10
(for internal I/O USB 6/7) are for selecting the power of USB ports. To enable Wake-on-USB
function, please select +5V_standby.
3
2
1
▲▲ 1-2 On: +5V (default)
JP4
USB 4/5
(USB 2.0)
USB 6/7
(USB 2.0)
Each of the two USB 3.0 rear channels (A and B) can act as a single USB 3.0 port without additional USB 2.0 ports, or as a single USB 2.0 port with two additional USB 2.0 ports enabled.
The two configurations can be switched via jumper settings (JP3 & JP4) as listed and illustrated below.
3
2
1
▲▲ 2-3 On: +5V_standby
JP4
USB 4/5
(USB 2.0)
Rear Port A
JP3
USB 6/7
(USB 2.0)
Rear Port B
1-2 On
Enabled
USB 2.0
1-2 On
Enabled
USB 2.0
2-3 On
(default)
Disabled
USB 3.0
2-3 On
(default)
Disabled
USB 3.0
3
2
1
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or
more USB ports, the +5V_standby power source of your power supply must support ≥2A.
▲▲ 1-2 On: Three USB 2.0
physical ports
9
3
2
1
▲▲ 2-3 On: One USB 3.0 (default)
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
►► Jumper Settings
►► Jumper Settings
Panel Power Select
Backlight Power Select
JP21
JP16
JP16 is for selecting the backlight power voltage — +5V or +3.3V.
JP21 is for selecting the power voltage supplied to the LCD panel.
1
3
5
2
4
6
▲▲ 1-2 On: +12
1
3
5
2
4
6
▲▲ 3-4 On: +5V
1
3
5
3
2
1
2
4
6
▲▲ 5-6 On: +3.3V
(default)
▲▲ 1-2 On: +3.3V (default)
Important:
Before powering on the system, make sure that the power setting of JP21 matches the LCD panel’s specification. Supplying an incorrect voltage to the panel may
result in serious damage.
3
2
1
▲▲ 2-3 On: +5V
Important:
Before powering on the system, make sure that the power setting of JP16 matches the specification of the backlight control. Supplying an incorrect voltage to the
panel backlight may result in serious damage.
10
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
►► Jumper Settings
►► Jumper Settings
LCD/Inverter Power Select
Dimming Mode Select
LCD/Inverter
Power
JP11
JP17
JP17 is for selecting the power voltage of the LCD/Inverter power.
3
2
1
▲▲ 1-2 On: +12V
JP11 is for selecting the mode for lightness control of the LVDS panel — PWM Mode or Voltage
Mode.
3
2
1
3
2
1
▲▲ 1-2 On: PWM Mode (default)
3
2
1
▲▲ 2-3 On: Voltage Mode
▲▲ 2-3 On: +5V (default)
Important:
Please make sure the mode (PWM or Voltage) is configured according to the
mode of your panel.
11
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Jumper Settings
►► Jumper Settings
BIOS Boot Select
ATX/AT Power Select
www.dfi.com
JP12
J9
J9 is for selecting the BIOS boot source — carrier board or Qseven module.
2
1
▲▲ 1-2 On: Boot from Carrier
Board SPI BIOS
JP12 is for selecting the ATX/AT power — 5V, 5V_standby, or N.C.
2
1
▲▲ 1-2 Off: Boot from Module
SPI BIOS
12
1 3 5
1 3 5
1 3 5
2 4 6
2 4 6
2 4 6
▲▲ 1-2 On: 5V
▲▲ 3-4 On: 5VSB
▲▲ 5-6 On: N.C.
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Jumper Settings
►► Jumper Settings
LPC/GPIO Switch
High/low Switch for MXM Pin 27
www.dfi.com
JP24
JP25
JP24 is for switching between LPC or GPIO (DIO) signals.
1 2 3
▲▲ 1-2 On: GPIO
JP25 is for switching between high and low voltage of the battery low/General Purpose Input
(GPI) pin (pin 27) of the MXM connector.
1 2 3
1 2 3
▲▲ 2-3 On: LPC (default)
▲▲ 1-2 On: High (3.3V,
default)
13
1 2 3
▲▲ 2-3 On: Low
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
►► Panel I/O Ports
►►Panel I/O Ports
12V DC-in
Rear panel I/O ports
▼▼ LAN
▼▼ DC-in
▼▼ USB 2.0
Line-in
▼▼ USB 2.0
▼▼ DP
Note
▲▲ DC-in
Line-out
Mic-in
▲▲ USB 3.0
•
•
•
•
•
•
•
•
1
3
3
1
1
1
1
1
▲▲ USB 3.0
Note
12V DC-in jack
USB 3.0 ports
USB 2.0 type A ports
DP port
RJ45 LAN port
Line-in/Surround jack
Line-out jack
Mic-in/Center+Subwoofer jack
This jack provides maximum of 100W power and is considered a low power solution. Connect
a DC power cord to this jack. Use a power adapter with 12V DC output voltage. Using a voltage higher than the recommended one may fail to boot the system or cause damage to the
system board.
Front panel I/O port
• 1 DP port
▲▲ DP
Note:
The two USB 3.0 rear ports under the LAN port can act 1) as a single USB 3.0
port with additional USB 2.0 ports disabled, or 2) as a single USB 2.0 port with
two additional USB 2.0 ports enabled. Please refer to Jumper Settings of JP3 and
JP4 previously in this chapter for more information.
14
Q7X-151 (R.D1)
Chapter 2 - Hardware Installation
►► Panel I/O Ports
►► Panel I/O Ports
RJ45 LAN Port
DisplayPort
www.dfi.com
▼▼ LAN
▲▲ DisplayPort
▲▲ DisplayPort
The onboard RJ45 LAN port allows the system board to connect to a local area network by
means of a network hub.
DisplayPort is a digital display interface used to connect a display device such as a computer
monitor. It is used to transmit audio and video simultaneously. The interface, which is developed by VESA, delivers higher performance features than any other digital interface.
15
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
►► Panel I/O Ports
USB Ports
USB 2.0 / USB 3.0 signal switch
According to the maximum number of USB 2.0 and USB 3.0 ports supported by different
Qseven modules, this carrier board is designed with two numbers of USB ports configurable as
listed below.
USB 2.0 (USB 3)
USB 3.0 (USB 1)
A USB 3.0 (USB 2)
B USB 3.0 (USB 0)
USB 2.0 (USB 5)
USB 2.0 (USB 4)
JP4
USB 4/5
(USB 2.0)
Rear Port A
JP3
USB 6/7
(USB 2.0)
Rear Port B
1-2 On
Enabled
USB 2.0
1-2 On
Enabled
USB 2.0
2-3 On
(default)
Disabled
USB 3.0
2-3 On
(default)
Disabled
USB 3.0
Key
GND
+Data
-Data
VCC
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function:
1
2
Driver Installation
You may need to install the proper drivers in your operating system to use the USB device.
Refer to your operating system’s manual or documentation for more information.
USB 2.0
(USB 6/7)
N. C.
GND
+Data
-Data
VCC
9
10
Jumper Settings
USB power and USB 2.0 / USB 3.0 signal switch are configured via jumper settings as previously instructed in this chapter.
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with three onboard USB 3.0 ports (USB 0/1/2) and three onboard USB 2.0 type A ports (USB 3/4/5). The 10-pin internal headers allow for 2 additional
USB 2.0 ports (USB 6/7).
The internal USB pin headers may be connected to a card-edge bracket. Install the card-edge
bracket to an available slot at the rear of the system chassis and then insert the USB port
cables to a connector.
16
Q7X-151 (R.D1)
Chapter 2 - Hardware Installation
►► Panel I/O Ports
Audio
Line-in
Line-out
Mic-in
Rear Audio
The system board is equipped with 3 rear audio jacks (Line-in, Line-out, and Mic-in) as introduced below.
•
Line-in Jack (Light Blue)
This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player,
AM/FM radio tuner, synthesizer, etc.
•
Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
•
Mic-in Jack (Pink)
This jack is used to connect an external microphone.
BIOS Setting
Please refer to the manuals of a compatible Qseven module mounted on the carrier board for
more information on BIOS settings.
17
www.dfi.com
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►►Internal I/O Connectors
www.dfi.com
Front Panel
SMBus Connector
▼▼ Front Panel Connector
1 2
PWR-LED
HD-LED
▼▼ SMBus Connector
ATX-SW
RESET
5
11 12
2 1
▼▼ Front Panel Pin Assignment
Pin
HD-LED
The SMBus (System Management Bus) connector is used to connect the SMBus device. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
RESET
Assignment
1
N.C.
3
HDD Power
5
7
9
Signal
11
Pin
Assignment
2
LED Power
4
LED Power
Signal
6
Signal
Ground
8
Ground
10
Signal
12
---
N.C.
PWR-LED
ATX-SW
▼▼ SMBus Pin Assignment
Pin Assignment
HDD-LED - Hard Disk Drive LED
Lighting of the LED indicates that the hard drive is being accessed.
Pin Assignment
1
3V3SB
2
GND
3
SMBus_Clock
4
SMBus_DATA
5
SMBus_Alert
6
---
RESET - Reset Switch
This switch allows you to reboot without having to power off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will light up. When the system is in the S1 (POS
- Power On Suspend) state, it will blink at 1-second intervals. When the system is in the S3
(STR - Suspend To RAM) state, it will blink at 4-second intervals.
ATX-SW - ATX Power Switch
This switch is used to power on or off the system.
18
Q7X-151 (R.D1)
Chapter 2 - Hardware Installation
►► Internal I/O Connectors
►► Internal I/O Connectors
Cooling Fan Connector
CAN-Bus Connector
www.dfi.com
▼▼ System Fan 1
3
Ground
Power
Sense
1
▼▼ CAN-Bus
CAN_TX
GND
CAN_RX
NC
1
This 3-pin fan connector is for connection to a cooling fan. The cooling fan will provide adequate airflow throughout the chassis to prevent overheating the system board components.
The CAN controller performs communication in accordance with the BOSCH CAN Protocol Version 2.0B Active1 (standard format and extended format). The bit rate can be programmed to
a maximum of 1Mbit/s. To connect the CAN controller module to the CAN bus, it is necessary
to add transceiver hardware.
When communicating in a CAN network, individual message objects are configured. The message objects and the identifier masks for the receive filter for the received messages are
stored in the message RAM.
Controller Area Network (CAN or CAN-bus) is a message-based protocol originally designed for
automotive applications, and is now widely used in other areas such as industrial automation,
medical equipment and etc.
19
Q7X-151 (R.D1)
Chapter 2 - Hardware Installation
www.dfi.com
►► Internal I/O Connectors
LVDS LCD Panel
▼▼ LCD/Inverter Power
▼▼ LVDS LCD Panel Pin Assignment
1
Pin Function
8
39
1
40
2
▲▲ LVDS LCD Panel
The system board allows you to connect a LCD Display Panel by means of the LVDS LCD panel
connector and the LCD/Inverter power connector. These connectors transmit video signals and
power from the system board to the LCD Display Panel.
Refer to the right side for the pin functions of these connectors.
Jumper Settings
Refer to the “Jumper Settings” section previously in this chapter to set up LCD panel relevant
jumpers — Panel Power Select, Backlight Power Select, LCD/Inverter Power Select, and Dimming Mode Select.
Note:
DFI board’s LVDS connector: Hirose DF13-40DP-1.25V(91)/40P/1.25mm; cable
side connector: Hirose DF13-40DS-1.25C.
20
Pin Function
▼▼ LCD/Inverter Power Pin Assignment
Pin Function
1
GND
2
GND
1
GND
3
LVDS_Out3+
4
LVDS_Out7+
2
GND
5
LVDS_Out3-
6
LVDS_Out7-
3
7
GND
8
GND
Panel Inverter Brightness
Voltage Control
4
Panel Power
9
LVDS_Out2+
5
+3.3V
6
Panel Backlight
On/Off Control
7
LCD/Inverter Power:
12V/5V (default)
8
LCD/Inverter Power: 12V/5V
(default)
10 LVDS_Out6+
11 LVDS_Out2-
12 LVDS_Out6-
13 GND
14 GND
15 LVDS_Out1+
16 LVDS_Out5+
17 LVDS_Out1-
18 LVDS_Out5-
19 GND
20 GND
21 LVDS_Out0+
22 LVDS_Out4+
23 LVDS_Out0-
24 LVDS_Out4-
25 GND
26 GND
27 LVDS_CLK1+
28 LVDS_CLK2+
29 LVDS_CLK1-
30 LVDS_CLK2-
31 GND
32 GND
33 LVDS_DDC_CLK
34 N.C.
35 LVDS_DDC_DATA
36 +3.3V
37 Panel Power
38 Panel Power
39 Panel Power
40 Panel Power
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
►► Internal I/O Connectors
►► Internal I/O Connectors
SATA (Serial ATA) Connectors
SATA (Serial ATA) Power Connectors
SATA 0
(SATA 3.0)
SATA Power 0
SATA 1
(SATA 3.0)
SATA Power 1
1
GND
TX+
TXGND
RXRX+
GND
+5V
Ground
Ground
+12V
7
4
1
▲▲ SATA Power Pin Assignment
▲▲ SATA 3.0 Pin Assignment
The Serial ATA (SATA) connectors are used to connect the Serial ATA device. SATA 3.0 is supported by the two SATA ports and provides data rate up to 6Gb/s. Connect one end of the Serial ATA cable to a SATA connector and the other end to your Serial ATA device.
The SATA power connectors supply power to the SATA drive. Connect one end of the provided
power cable to the SATA power connector and the other end to your storage device.
BIOS Setting
Please refer to the manuals of a compatible Qseven module mounted on the carrier board for
more information on BIOS settings.
21
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Internal I/O Connectors
►► Internal I/O Connectors
LPC Debug connector
I2C Connector
2
14
1
13
▲▲ LPC Connector
▼▼ I2C Pin Assignment
5
I2C_DATA
GND
The LPC connector is used for the debug function and its pin functions are listed below.
Pin Assignment
1
L_CLK
2
L_LAD1
3
L_RST#
4
L_LAD0
5
L_FRAME#
6
3.3V
7
L_LAD3
8
GND
9
L_LAD2
10
---
11
INT_SERIRQ
12
DEBUG_48M_CLK
13
5VSB
14
5V
2 1
NC
I2C_Clock
+3.3V
The 1-channel I2C bus interface conforms to the version 2.1 I2C bus specification. It operates
as a master or slave device and supports a multi-master bus.
▼▼ LPC Pin Assignment
Pin Assignment
www.dfi.com
22
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
www.dfi.com
►► Internal I/O Connectors
Expansion Slots
PCI Express x1 Slot
Install PCI Express cards such as network cards or other cards that comply to the PCI Express
specifications into the PCI Express x1 slot.
Mini PCIe Socket
The Mini PCIe socket is used to install a half-sized 52-pin Mini PCIe card. Mini PCIe card is a
small form factor PCIe card with the same signal protocol, electrical definitions, and configuration definitions as the conventional PCIe.
SDIO Slot
This expansion port is used to insert a Secure Digital Input/Output (SDIO) or Multimedia Card
(MMC) device. Aside from storing data files, a SDIO card is also capable of storing powerful
software applications.
Top View
Mini PCIe 1
Mini PCIe 2
PCIE1 (PCIe x1)
PCIE2 (PCIe x1)
Bottom View
SDIO
23
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Internal I/O Connectors
www.dfi.com
►► Expansion Slots
Installing the Mini PCIe card
Before installing the Mini PCIe module into the Mini PCIe socket, please make sure that the
following safety cautions are well-attended.
1. Make sure the PC and all other peripheral devices connected to it has been powered
down.
Step 1:
Insert the card into the socket at an
angle while making sure the notch
and key are perfectly aligned.
2. Disconnect all power cords and cables.
3. Locate the Mini PCIe socket on the system board
4. Make sure the notch on card is aligned to the key on the socket.
mSATA Half Size
Mini PCIe Socket
Stand-off
Notch
Step 2:
Press the end of the card far from
the socket down until against the
stand-off.
Key
Step 3:
Screw tight the card onto the standoff with a screw driver and a standoff screw until the gap between the
card and the stand-off closes up.
The card should be lying parallel to
the board when it’s correctly mounted.
Please follow the steps below to install the card into the socket.
24
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Internal I/O Connectors
►► Internal I/O Connectors
Switches
LEDs
www.dfi.com
GPO LED
▲▲ Lid
•
•
•
•
▲▲ Sleep
▲▲ Power
Thermal Trip LED
▲▲ Reset
Thermal Trip LED
This LED will light to indicate that the processor is on an overheating status.
Lid — turn the LVDS panel on or off
Sleep — set the system to “sleep” or “wake-up” mode
Power — power on or off the system
Reset — reset the system
GPO LED
This LED will light red when the General Purpose Output (GPO) signal (pin 19 of the MXM
connector) is active. The function of the GPO signal is dependent on the design of the Qseven
module. Please refer to the pin definition of the Qseven module for more information.
Note:
The Sleep and Lid functions are supported only when your operating system supports ACPI.
25
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Internal I/O Connectors
►► Internal I/O Connectors
Battery
MXM Connector
2
1
GND
+3.3V
www.dfi.com
▲▲ Battery
MXM Socket
The MXM connector is used to interface the carrier board with a Qseven R2.1 compatible module. Refer to the table in the following page for the pin functions of the MXM connector.
Battery
Connect to the
battery connector
The lithium ion battery addendum supplies power to the real-time clock and CMOS memory as
an auxiliary source of power when the main power is shut off.
Safety Measures
• There exists explosion hazard if the battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to local ordinances.
26
Chapter 2 - Hardware Installation
Q7X-151 (R.D1)
►► Internal I/O Connectors
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
www.dfi.com
►► MXM Connector
Q7 R2.1 Signal
GND
GBE_MDI3GBE_MDI3+
GBE_LINK100#
GBE_MDI1GBE_MDI1+
GBE_LINK#
GBE_CTREF
WAKE#
GPO0
SLP_BTN# /GPII1
GND
KEY
GND
BATLOW# /GPII2
SATA0_TX+
SATA0_TXSATA_ACT#
SATA0_RX+
SATA0_RXGND
BIOS_DISABLE# / BOOT_ALT#
SDIO_CD#
SDIO_CMD
SDIO_PWR#
SDIO_DAT0
SDIO_DAT2
RSVD
RSVD
GND
HDA_SYNC / I2S_WS
HDA_RST# / I2S_RST#
HDA_BITCLK / I2S_CLK
HDA_SDI / I2S_SDI
HDA_SDO / I2S_SDO
THRM#
THRMTRIP#
GND
USB_P7- / USB_SSTX0USB_P7+ / USB_SSTX0+
USB_6_7_OC#
USB_P5- / USB_SSTX2USB_P5+ / USB_SSTX2+
USB_2_3_OC#
USB_P3USB_P3+
USB_VBUS
USB_P1-
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
Q7 R2.1 Signal
GND
GBE_MDI2GBE_MDI2+
GBE_LED_1000GBE_MDI0GBE_MDI0+
GBE_ACT#
SUS_S5#
SUS_S3#
PWRBTN#
LID_BTN# /GPII0
GND
KEY
PWGIN
RSTBTN#
SATA1_TX+
SATA1_TXGND
SATA1_RX+
SATA1_RXGND
SDIO_CLK#
RSVD
SDIO_WP
SDIO_DAT1
SDIO_DAT3
RSVD
RSVD
USB_OTG_PEN
GND
SMB_CLK / GP1_I2C_CLK
SMB_DAT / GP1_I2C_DAT
SMB_ALERT#
GP0_I2C_CLK
GP0_I2C_DAT
WDTRIG#
WDOUT
GND
USB_P6- / USB_SSRX0USB_P6+ / USB_SSRX0+
USB_4_5_OC#
USB_P4- / USB_SSRX2USB_P4+ / USB_SSRX2+
USB_0_1_OC#
USB_P2USB_P2+
USB_ID
USB_P0-
Pin
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
Q7 R2.1 Signal
USB_P1+
GND
eDP0_TX0+ / LVDS_A0+
eDP0_TX0- / LVDS_A0eDP0_TX1+ / LVDS_A1+
eDP0_TX1- / LVDS_A1eDP0_TX2+ / LVDS_A2+
eDP0_TX2- / LVDS_A2LVDS_PPEN
eDP0_TX3+ / LVDS_A3+
eDP0_TX3- / LVDS_A3GND
eDP0_AUX+ / LVDS_A_CLK+
eDP0_AUX- / LVDS_A_CLKLVDS_BLT_CTRL /GP_PWM_OUT0
GP2_I2C_DAT / LVDS_DID_DAT
GP2_I2C_CLK / LVDS_DID_CLK
CAN0_TX
DP_LANE3+ / TMDS_CLK+
DP_LANE3- / TMDS_CLKGND
DP_LANE1+ / TMDS_LANE1+
DP_LANE1- / TMDS_LANE1GND
DP_LANE2+ / TMDS_LANE0+
DP_LANE2- / TMDS_LANE0GND
DP_LANE0+ / TMDS_LANE2+
DP_LANE0- / TMDS_LANE2HDMI_HPD#
PCIE_CLK_REF+
PCIE_CLK_REFGND
PCIE3_TX+
PCIE3_TXGND
PCIE2_TX+
PCIE2_TXUART0_TX
PCIE1_TX+
PCIE1_TXUART0_RX
PCIE0_TX+
PCIE0_TXGND
LPC_AD0 / GPIO0
LPC_AD2 / GPIO2
LPC_CLK / GPIO4
27
Pin
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
Q7 R2.1 Signal
USB_P0+
GND
eDP1_TX0+ / LVDS_B0+
eDP1_TX0- / LVDS_B0eDP1_TX1+ / LVDS_B1+
eDP1_TX1- / LVDS_B1eDP1_TX2+ / LVDS_B2+
eDP1_TX2- / LVDS_B2LVDS_BLEN
eDP1_TX3+ / LVDS_B3+
eDP1_TX3- / LVDS_B3GND
eDP1_AUX+ / LVDS_B_CLK+
eDP1_AUX- / LVDS_B_CLKGP_1-Wire_Bus /HDMI_CEC
eDP0_HPD# / LVDS_BLC_DAT
eDP1_HPD# / LVDS_BLC_CLK
CAN0_RX
USB_SSTX1USB_SSTX1+
GND
DP_AUX+
DP_AUXGND
USB_SSRX1USB_SSRX1+
GND
HDMI_CTRL_DAT
HDMI_CTRL_CLK
DP_HPD#
PCIE_WAKE#
PCIE_RST#
GND
PCIE3_RX+
PCIE3_RXGND
PCIE2_RX+
PCIE2_RXUART0_RTS#
PCIE1_RX+
PCIE1_RXUART0_CTS#
PCIE0_RX+
PCIE0_RXGND
LPC_AD1 / GPIO1
LPC_AD3 / GPIO3
LPC_FRAME# / GPIO5
Pin Q7 R2.1 Signal
191 SERIRQ/
GPIO6
193 VCC_RTC
195 FAN_TACHOIN/
GP_TIMER_IN
197 GND
199 SPI_MOSI
201 SPI_MISO
203 SPI_SCK
205 VCC_5V_SB
207 MFG_NC0
209 MFG_NC1
211 NC
213 NC
215 NC
217 NC
219 VCC
221 VCC
223 VCC
225 VCC
227 VCC
229 VCC
Pin Q7 R2.1 Signal
192 LPC_LDRQ#/
GPIO7
194 SPKR/GP_PWM_OUT2
196 FAN_PWMOUT/
GP_PWM_OUT1
198 GND
200 SPI_CS0#
202 SPI_CS1#
204 MFG_NC4
206 VCC_5V_SB
208 MFG_NC2
210 MFG_NC3
212 NC
214 NC
216 NC
218 NC
220 VCC
222 VCC
224 VCC
226 VCC
228 VCC
230 VCC
Q7X-151 (R.D1)
Chapter 3 - Supported Software
Chapter 3 - Supported Software
► Realtek Audio Drivers
Install drivers, utilities and software applications that are required to facilitate and enhance the
performance of the system board. You may acquire the software from your sales representatives, from an optional DVD included in the shipment, or from the website download page at
https://www.dfi.com/DownloadCenter.
To install the driver, click “Realtek Audio Drivers” on the main menu.
1. Setup is now ready to install the
audio driver. Click Next.
2. Follow the remainder of the steps
on the screen; clicking “Next”
each time you finish a step.
3. Click “Yes, I want to restart my
computer now” then click Finish.
Restarting the system will allow
the new software installation to
take effect.
Note:
This step can be ignored if the applications are downloaded standalone files.
28
www.dfi.com
Q7X-151 (R.D1)
Chapter 3 - Supported Software
► Adobe Acrobat Reader 9.3
To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.
1. Click Next to install or click
Change Destination Folder to
select another folder.
2. Click Install to begin installation.
3. Click Finish to exit installation.
29
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising