Dfi SU251/SU253 Manual
SU251/SU253
Embedded SBC 4”
User’s Manual
A43840952
1
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2017. All Rights Reserved.
Notice:
Trademarks
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2
Table of Contents
Graphics Interfaces .................................................................. 18
USB Ports................................................................................ 19
COM (Serial) Ports ................................................................... 20
RJ45 LAN Ports ........................................................................ 21
Audio ...................................................................................... 21
Copyright .......................................................... 2
I/O Connectors...................................................................................................22
Trademarks ....................................................... 2
Serial ATA Connector ................................................................ 22
Serial ATA Power Connector....................................................... 22
LVDS LCD Panel Connector ........................................................ 23
LCD/Inverter Power Connector ................................................... 23
Cooling Fan Connector .............................................................. 24
Chassis Intrusion Connector ..................................................... 24
Expansion Slots ....................................................................... 25
SMBus Connector ..................................................................... 25
Front Panel Connector .............................................................. 26
Standby Power LED .................................................................. 27
Battery ................................................................................... 27
FCC and DOC Statement on Class B ...... 2
About this Manual .......................................... 4
Warranty ......................................................... 4
Chapter 3 - BIOS Setup.............................. 28
Static Electricity Precautions........................ 4
Overview .............................................................................................................28
Insyde BIOS Setup Utility .................................................................................29
Safety Measures ............................................... 4
Main ....................................................................................... 29
Advanced ............................................................................... 29
Security .................................................................................. 39
Boot ....................................................................................... 41
Exit ........................................................................................ 43
Before Using the System Board .................. 5
Chapter 1 - Introduction .............................. 6
Updating the BIOS .............................................................................................44
Notice: BIOS SPI ROM......................................................................................44
Chapter 2 - Hardware Installation ............. 8
Chapter 4 - Supported Software .............. 45
Board Layout.......................................................................................................... 8
Block Diagram ....................................................................................................... 9
Mechanical Diagram ............................................................................................. 9
System CPU .........................................................................................................10
Chapter 5 - RAID ....................................... 60
Chapter 6 - Intel AMT Settings................. 64
Installing the Heat Sink ............................................................ 10
System Memory ..................................................................................................11
Jumper Settings ...................................................................................................11
Appendix A - Troubleshooting Checklist 77
Clear CMOS Data ..................................................................... 11
Auto Power-on Select ............................................................... 12
Mini PCIe Signal Select ............................................................. 12
LVDS Backlight Voltage Select ................................................... 13
LVDS DIMM Control .................................................................. 13
LVDS Panel Voltage Select......................................................... 14
COM4/DIO Pin Select ................................................................ 14
eDP Backlight Voltage Select (optional)....................................... 15
eDP Panel Voltage Select (optional) ............................................ 15
eDP Invert Voltage Select (optional) ........................................... 16
Front Panel I/O Ports ........................................................................................17
Rear Panel I/O Ports .........................................................................................17
12V DC-in (SU251)/15~36V DC-in (SU253) ................................ 18
3
About this Manual
Static Electricity Precautions
This manual can be downloaded from the website, or acquired as an electronic file included in
the optional CD/DVD. The manual is subject to change and update without notice, and may be
based on editions that do not resemble your actual products. Please visit our website or contact our sales representatives for the latest editions.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
2. Wear an antistatic wrist strap.
1. Warranty does not cover damages or failures that arised from misuse of the product, inability to use the product, unauthorized replacement or alteration of components and product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
4
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
•
Storage devices such as hard disk drive, DVD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1
Chapter 1 - Introduction
Specifications
SYSTEM
GRAPHICS
Processor
Memory
6th Generation Intel® CoreTM Processors, BGA 1356 (Skylake-U*)
Intel® CoreTM i7-6600U Processor, Dual Core, 4M Cache, 2.6GHz (3.4GHz), 15W
Intel® CoreTM i5-6300U Processor, Dual Core, 3M Cache, 2.4GHz (3.0GHz), 15W
Intel® CoreTM i3-6100U Processor, Dual Core, 3M Cache, 2.3GHz, 15W
Intel® Celeron® Processor 3955U, Dual Core, 2M Cache, 2.0GHz, 15W
4GB/8GB Memory Down
Dual Channel DDR4 2133MHz
BIOS
Insyde SPI 128Mbit
Controller
Intel® HD Graphics GT Series
Feature
OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9
1 x VGA
1 x DP++/HDMI (HDMI available upon request)
1 x LVDS/eDP (eDP available upon request)
VGA: resolution up to 1920x1200 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
HDMI: resolution up to 2560x1600 @ 60Hz or 4096x2160 @ 24Hz
LVDS: dual channel 48-bit, resolution up to 1920x1200 @ 60Hz
eDP: resolution up to 3840x2160 @ 60Hz
VGA +
DP++/HDMI (HDMI available upon request) +
LVDS/eDP (eDP available upon request)
1 x Full-size Mini PCIe (PCIe/USB)
1 x Half-size Mini PCIe (USB + PCIe/SATA, PCIe/SATA select by jumper setting,
SATA by default)
Realtek ALC888S-VD2-GR
Display
Triple
Displays
EXPANSION Interface
AUDIO
ETHERNET
Audio
Codec
Controller
Front I/O
Serial
Display
Button
Rear I/O
Ethernet
Serial
USB
Audio
Display
INTERNAL I/O
Serial
USB
Display
Audio
SATA
SMBus
Other I/O
WATCHDOG TIMER Output &
Interval
SECURITY
TPM
POWER
Type
Connector
Consumption
RTC Battery
OS SUPPORT
2 x RS-232 (2.0mm pitch)
2 x USB 2.0 (2.00mm pitch)
1 x LVDS LCD Panel Connector
1 x LCD/Inverter Power
Supports optional eDP connector
1 x Audio (Line-out/Mic-in)
2 x SATA 3.0 (up to 6Gb/s)
1 x SATA Power
1 x SMBus
1 x front panel; 1 x chassis intrusion; 1 x fan connector
System Reset, Programmable via Software from 1 to 255 Seconds
Available Upon Request
Single 12V +/-10% DC (SU251)
Wide Range 15~36V (SU253)
2-pin Terminal Block
SU251
Typical: 6600U:12V @ 0.45A (5.44Watt)
Max: 6600U:12V @ 3.14A (37.67Watt)
SU253
Typical: 6600U:19V @ 0.46A (8.7Watt)
Max: 6600U:19V @ 2.07A (39.29Watt)
CR2032 Coin Cell
Windows 7 (/WES7) (32/64-bit)
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise (64-bit)
Debian 8 (with VESA graphic driver)
CentOS 7 (with VESA graphic driver)
Ubuntu 15.10 (Intel graphic driver available)
ENVIRONMENT
Temperature Operating: 0 to 60°C
Storage: -40 to 85°C
Humidity
Operating: 5 to 90% RH
Storage: 5 to 90% RH
MTBF
SU251: 369,377 hrs @ 25°C; 205,103 hrs @ 45°C; 123,607 hrs @ 60°C
SU253: 359,921 hrs @ 25°C; 199,960 hrs @ 45°C; 120,832 hrs @ 60°C
Calculation model: Telcordia Issue 2, Method I Case 3
Environment: GB, GC – Ground Benign, Controlled
MECHANICAL
Dimensions
4" SBC Form Factor
165mm (6.49") x 115mm (4.53")
Height
PCB: 1.6mm
Top Side: TBD, Bottom Side: TBD
* When Intel Skylake-U processors are used for stress test with the BurnInTest™ software, it may result in
CPU throttling. We provide a workaround for this situation. For more information, please contact our technical support at http://www.dfi.com/support/support.html.
1 x Intel® I210AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps)
(only Core i7/i5 supports iAMT)
2 x RS-232/422/485; 1 x RS-232( also supports an optional 8-bit DIO)
1 x VGA
1 x Power Button
1 x Reset Button
2 x GbE (RJ-45)
1 x RS-232
4 x USB 3.0
Mic-in; Line-out
1 x DP++/HDMI
Microsoft/
Linux
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Features
• Wake-On-LAN
• Watchdog Timer
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Management Event) signal. However, if your system is in the Suspend mode, you can power-on
the system only through an IRQ or DMA interrupt.
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• DDR4
DDR4 deliver increased system bandwidth and improved performance. The advantages of
DDR4 are its higher bandwidth and its increase in performance at a lower power than DDR3
and DDR3L. It is not compatible with older standards of DDR memories.
• Wake-On-USB (optional)
• Graphics
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications. Supports 1 LVDS (or eDP), 1
DisplayPort (or HDMI) and 1 VGA interfaces for display outputs.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the 5V_standby power source of your power supply must support ≥2A.
• Serial ATA
• ACPI STR
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s.
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
• Gigabit LAN
Two Intel® Gigabit LAN controllers (Intel® I210AT PCI Express Gigabit Ethernet controller and
Intel® I219LM Gigabit Ethernet Phy) support up to 1Gbps data transmission.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to go
through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.
• Audio
The Realtek ALC888S-VD2-GR audio codec provides 5.1-channel High Definition audio output.
• Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
Important:
The 5V standby power source of your power supply must support ≥720mA.
• USB
• RTC Timer
The system board supports the new USB 3.0. It is capable of running at a maximum transmission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement in
device transfer speeds between your computer and a wide range of simultaneously accessible
external Plug and Play peripherals.
The RTC installed on the system board allows your system to automatically power-on on the
set date and time.
7
Chapter 1 Introduction
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
COM 3
SATA 2 SATA Power
1
1
LAN 2
USB 4
USB 3
USB 3.0
DP
LINE-out
1
2
CPU fan
LAN 1
2
Front Audio
Realtek ALC888
MIC-in
USB 2
USB 1
USB 3.0
DC-in
1
SATA 0
SATA 3.0
Chassis
Intrusion
COM 5
COM 6
2
2
1
1
Intel
WGI219LM
Intel
WGI210AT
Mini PCIe
USB 2.0 1/2
1
10
JP1
Auto PWR ON
5
12
1
1
DDR4
SMBus
JP2
1
Battery
JP3 1
JP4 1
JP5 1
JP12
1
1
6
COM 4
COM4/DIO Pin Select
COM4/DIO Pin Select
Mini PCIe PCIe/
SATA Select
Clear CMOS
eDP Backlight
Voltage Select
eDP Panel
Voltage Select
eDP Invert
Voltage Select
LVDS LCD Panel
40
SPI Flash
BIOS
5
JP7 JP8 JP9
Front
Panel
(JP11)
VGA
39
DDR4
DDR4
DDR4
Nuvoton
NCT6106
2
NXP
PIN3460
1
1
COM 2
DDR4
6
1
3 3 3
Intel
(JP7)
LVDS Backlight
(JP8)
Voltage Select
LVDS DIMM Control (JP9)
LVDS Panel
(JP10)
Voltage Select
DDR4
2 1
JP6
1
DDR4
Mini PCIe
12
DDR4
5
LCD/Inverter
JP10 Power
Reset Power
COM 1
(JP1)
(JP2)
(JP3)
Bottom View
(JP4)
(JP5)
(JP6)
(JP12)
Top View
8
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Block Diagram
PCIe x1
USB 2.0
SPI
SMBus
TPM (Opt.)
RS-232/422/485 2x
RS-232 4x
H/W Monitor
7.29
USB 2.0
SATA 3.0
160.00
129.90
8.00
0.00
USB 3.0 4x
USB 2.0 2x
0.00
USB 2.0
24.00
18.00
USB 3.0
SATA 2x
142.82
Half-size
Mini PCIe
165.00
HD Audio
Codec
106.90
PCIe x1
SATA 3.0
147.40
Core
i7/i5/i3
103.20
123.21
Audio Jack
(Line-out/Mic-in)
PCIe x1
107.55
98.20
106.50
GLAN I210AT
PCIe x1
115.00
Full-size
Mini PCIe
87.09
GLAN I219LM
USB 2.0
75.40
2GB/4GB DDR4
Memory Down
71.02
Channel B
73.05
DDI
58.99
DP++/HDMI
2GB/4GB DDR4
Memory Down
35.52
CH7517
Channel A
DDI
40.27
R.G.B
eDP
23.77
VGA
PTN3460
5.00
6.10
14.90
LVDS
Mechanical Diagram
SMBus
LPC Bus
Super IO
with WDT
9
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
System CPU
2. Use the standoffs and captive
screws to fasten the heat sink on
the system board.
The system board is equipped with a Skylake-U microprocessor in socket BGA compatible
package 1356.
Captive screws
Standoffs
Installing the Heat Sink
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system
board.
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of the
CPU. The thermal paste is usually supplied when you purchase the fan / heat sink assembly. Do not spread the paste all over the surface. When you later place the heat sink on
top of the CPU, the compound will disperse evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel the
strip that covers the paste before you place the fan / heat sink on top of the CPU.
2. Place the heat sink on top
of the CPU. The 4 captive
screws around the heat
sink, which are used to
secure the heat sink onto
the system board, must
match the 4 mounting
holes around the CPU on
the system board.
Mounting
holes
10
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Jumper Settings
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Clear CMOS Data
System Memory
Important:
When the Standby Power LED lights red, it indicates that there is power on the system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
JP4
1 2 3
1 2 3
1-2 On:
Normal
2-3 On:
Clear CMOS Data
If you encounter the following,
DDR4
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
you can reconfigure the system with the default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
Features
•
4GB/8GB Memory Down
•
Dual channel DDR4 2133MHz
1. Power-off the system and unplug the power cord.
2. Set JP4 pins 2 and 3 to On. Wait for a few seconds and set JP4 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
11
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Auto Power-on Select
1
2
3
1-2 On:
Normal
Mini PCIe Signal Select
1
2
3
2-3 On:
Auto-Power on
1 2 3
JP3
JP7
JP7 is used to select the method of powering on the system. If you want the system to power-on whenever AC power comes in, set JP7 pins 2 and 3 to On. If you want to use the power
button, set pins 1 and 2 to On.
1-2 On: SATA
1 2 3
2-3 On: PCIe
JP3 is used to select the Mini PCIe signal: PCIe or mSATA (default).
When using the JP7 “Power On” feature to power the system back on after a power failure
occurs, the system may not power on if the power lost is resumed within 5 seconds (power
flicker).
12
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LVDS Backlight Voltage Select
1
2
3
1-2 On:
+3.3V
LVDS DIMM Control
1
2
3
1
2
3
JP8
1-2 On:
DC Mode
2-3 On:
+5V
1
2
3
JP9
2-3 On:
PWM Mode
JP9 allows you to select the mode for the lightness control of the LVDS panel.
JP8 allows you to select the power level of the LVDS backlight brightness control: 3.3V or 5V.
Important:
Before powering-on the system, make sure that the power settings of JP8 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
Important:
You need to refer to your panel’s user guide to determine the type of mode most appropriate for your panel.
13
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LVDS Panel Voltage Select
COM4/DIO Pin Select
2 4 6
2 4 6
2 4 6
1 3 5
1 3 5
1 3 5
3-4 On:+5V
5-6 On: +3.3V
1-2 On: +12V
JP1
JP10
JP2
1
3
1
3
10
12
10
12
1-2, 4-5, 7-8,
10-11 On:
COM4
2-3, 5-6, 8-9,
11-12 On:
DIO
The system board uses JP1 and JP2 to select between RS232/422/485 COM 4 or isolated 8-bit
DIO at the rear panel.
JP10 allows you to select the power voltage of the LVDS panel.
Important:
Before powering-on the system, make sure that the power settings of JP10 match the
power specification of LVDS panel’s specification. Selecting the incorrect voltage will
seriously damage the LVDS panel. .
Important:
You cannot use COM 4 and DIO at the same time. Please set up JP1 and JP2 together.
14
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
eDP Backlight Voltage Select (optional)
1 2 3
JP5
1-2 On: +3.3V
eDP Panel Voltage Select (optional)
1 2 3
JP6
2-3 On: +5V
5
6
3
4
1
2
1-2 On: +12V
5
6
3
4
1
2
3-4 On:+5V
6
4
2
5
3
1
5-6 On: +3.3V
JP6 is used to select the power supplied with the LCD panel.
JP5 is used to select the power level of backlight brightness control: +3.3V or +5V.
Important:
Before powering-on the system, make sure that the power settings of JP6 match the
LCD panel’s specification. Selecting the incorrect voltage will seriously damage the
LCD panel.
Important:
Before powering-on the system, make sure that the power settings of JP5 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
15
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
eDP Invert Voltage Select (optional)
1 2 3
JP12
1-2 On: +12V
1 2 3
2-3 On: +5V
JP12 is used to select the power level of the LCD/inverter power connector: +12V or +5V.
16
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Front Panel I/O Ports
Rear Panel I/O Ports
USB 3.0
COM 4
VGA
COM 2
COM 1
DP++
Power
Button
Reset
Button
LAN 1 LAN 2
The front panel I/O ports consist of the following:
Mic-in
The rear panel I/O ports consist of the following:
•3 serial ports
- Two of them support RS232/422/485
- One (COM4) supports only RS232 with an optional 8-bit DIO
• 1 VGA port
• 1 power button
• 1 reset button
•
•
•
•
•
•
17
Chapter 2 Hardware Installation
USB 3.0
2
4
1
1
1
1
RJ45 LAN ports
USB 3.0 ports
DP++/HDMI (opitoanl) port
serial port supporting RS232
Mic-in jack
Line-out jack
Line-out
COM 3
Chapter 2
12V DC-in (SU251)/15~36V DC-in (SU253)
Graphics Interfaces
The display ports consist of the following:
•
•
DC-in
1 DP++/HDMI (optional) port
1 VGA port
DP++
+
VGA Port
VGA
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
This 2-pin terminal block provides maximum of 100W/120W power and is considered a low
power solution. Connect a DC power cord to this terminal block. Using a voltage more than
the recommended range may fail to boot the system or cause damage to the system board.
DP Port
The DP port is a digital display interface used to connect a display device such as a computer
monitor. It is used to transmit audio and video simultaneously. The interface, which is developed by VESA, delivers higher performance features than any other digital interface.
HDMI Port (optional)
The HDMI port which carries both digital audio and video signals is used to connect a LCD
monitor or digital TV that has the HDMI port.
BIOS Setting
Configure the display devices in the Chipset menu (“North Bridge Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
18
Chapter 2 Hardware Installation
Chapter 2
USB Ports
BIOS Setting
USB 3.0
USB 3
USB 1
USB 4
USB 2
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to chapter 3 for more information.
Driver Installation
You may need to install the proper drivers in your operating system to use the USB device.
Refer to chapter 4 for more information.
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
N.C.
GND
+Data1
-Data1
VCC
10 9
2 1
Key
GND
+Data0
-Data0
VCC
USB 1
USB 2
USB 2.0
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with four onboard USB 3.0 port (USB 1-4). The 10-pin connector allows you to connect 2 additional USB 2.0 port (USB 1-2). The additional USB port may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis and then insert the USB port cables to a connector.
19
Chapter 2 Hardware Installation
Chapter 2
COM (Serial) Ports
RS232
RS422
Full Duplex
DATA+
DATAN.C.
N.C.
GND
6789
1 2345
6789
N.C.
N.C.
N.C.
N.C.
RX+
RXTX+
TXGND
6789
N.C.
N.C.
N.C.
N.C.
1 2345
RS485
COM 4 (Serial) Port
COM 5/COM 6: RS232
This DB-9 serial port can be used as a RS232 COM port or as an isolated 8-bit DIO via the
jumper setting. Refer to “COM 4/DIO Select“ in this section for its respective configuration.
RD
DTRDSRCTS2
1
1 2345
DSRRTSCTSRI-
COM 3: RS232
DCDRXD
TXD
DTRGND
COM 1 (RS232/422/485) /COM 2 (RS232/422/485) /COM3 (RS232 only)
8-bit DIO (4-bit in and 4-bit out)
9
DCDTD
GND
RTSRI-
The 8-bit Digital I/O connector provides powering-on function to external devices that are connected to the connector.
Pins
COM 4
Function
DIO Function
RS232
COM 4 (or 8-bit DIO): RS232
COM 2: RS232/RS422/RS485
COM 1: RS232/RS422/RS485
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
BIOS Setting
Configure the serial ports in the Integrated Peripherals submenu (“NCT6106D Super I/O Configuration” section) of the BIOS. Refer to chapter 3 for more information.
20
Chapter 2 Hardware Installation
1
DCD
DIN0A
2
RX
DIN0B
3
TX
DIN1A
4
DTR
DIN1B
5
GND
GND
6
DSR
DOUT0A
7
RTS
DOUT0B
8
CTS
DOUT1A
9
RI
DOUT1B
Chapter 2
RJ45 LAN Ports
Audio
Mic-L
Mic-R
Line-R
GND
Line2-L
LAN 2 LAN 1
1 2
GND
N\C
Mic-JD
N\C
Line-JD
Line-out
Mic-in
9 10
Front Audio
Rear Audio
The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
Features
•
1 Intel® I210AT PCI Express Gigabit Ethernet controllers
•
1 Intel® I219LM PCI Express Gigabit Ethernet controllers
•
Line-out Jack
This jack is used to connect a headphone or external speakers.
•
Mic-in Jack
This jack is used to connect an external microphone.
Front Audio
The LAN ports allow the system board to connect to a local area network by means of a network hub.
The front audio connector allows you to connect to the second line-out and mic-in jacks that
are at the front panel of your system.
Driver Installation
Driver Installation
Install the LAN drivers. Refer to chapter 4 for more information.
Install the audio driver. Refer to the chapter 4 for more information.
21
Chapter 2 Hardware Installation
Chapter 2
I/O Connectors
Serial ATA Connector
Serial ATA Power Connector
4
+5V
Ground
Ground
+12V
1
1
GND
TXP
TXN
GND
RXN
RXP
GND
GND
TXP
TXN
GND
RXN
RXP
GND
7
1
7
SATA 3.0 6Gb/s
Features
•
1 Serial ATA 3.0 port with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
The Serial ATA connector is used to connect the Serial ATA device. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
The SATA power connector supplies power to the SATA drive. Connect one end of the provided
power cable to the SATA power connector and the other end to your storage device.
BIOS Setting
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to chapter 3 for more information.
22
Chapter 2 Hardware Installation
Chapter 2
LVDS LCD Panel Connector
LVDS LCD Panel Connector
LCD/Inverter Power Connector
Pins
Function
Pins
LCD/Inverter Power Connector
Function
Pins
Function
1
GND
2
GND
1
+12V
3
LVDS_Out3+ (Odd_3+)
4
LVDS_Out7+ (Even_3+)
2
GND
5
LVDS_Out3- (Odd_3-)
6
LVDS_Out7- (Even_3-)
3
Panel Backlight On/Off Control
7
GND
8
GND
4
Dimming Control
9
LVDS_Out2+ (Odd_2+)
10
LVDS_Out6+ (Even_2+)
5
+5V
11
LVDS_Out2- (Odd_2-)
12
LVDS_Out6- (Even_2-)
13
GND
14
GND
15
LVDS_Out1+ (Odd_1+)
16
LVDS_Out5+ (Even_1+)
17
LVDS_Out1- (Odd_1-)
18
LVDS_Out5- (Even_1-)
19
GND
20
GND
21
LVDS_Out0+ + (Odd_0+)
22
LVDS_Out4+ (Even_0+)
LCD/Inverter
power
23
LVDS_Out0-+ (Odd_0-)
24
LVDS_Out4- (Even_0-)
25
GND
26
GND
The system board allows you to connect a LCD Display Panel by means of the
LVDS LCD panel connector and the LCD/Inverter power connector. These connectors transmit video signals and power from the system board to the LCD
Display Panel.
27
LVDS_CLK1++ (Odd_CLK+)
28
LVDS_CLK2+(Even_CLK+)
29
LVDS_CLK1-+ (Odd_CLK-)
30
LVDS_CLK2- (Even_CLK-)
31
GND
32
GND
33
DDC_CLK
34
NC
35
DDC_DATA
36
+3.3V
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
40
39
2
LVDS LCD
panel
1
1
5
Refer to the right side for the pin functions of these connectors.
BIOS Setting
Configure the LCD panel in the Advanced menu (“Video Configuration” submenu) of the BIOS. Refer to the chapter 3 for more information.
Note:
DFI board's LVDS connector: Hirose DF13-40DP-1.25V(91)/40P/1.25mm; cable side
connector: Hirose DF13-40DS-1.25C.
23
Chapter 2 Hardware Installation
Chapter 2
Chassis Intrusion Connector
Signal
Ground
Cooling Fan Connector
1 2
1
3
Chassis
Intrusion
Ground
12V
Fan In
CPU Fan
The fan connector is used to connect the cooling fan. The cooling fan will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
The board supports the chassis intrusion detection function. Connect the chassis intrusion
sensor cable from the chassis to this connector. When the system’s power is on and a chassis
intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion
occurred, the alarm will sound only when the system restarts.
BIOS Setting
The Advanced menu (“HW Monitor” submenu) of the BIOS will display the current speed of
the cooling fans. Refer to chapter 3 for more information.
24
Chapter 2 Hardware Installation
Chapter 2
Expansion Slots
SMBus Connector
5
SMBUS_Data
GND
Half-size Mini PCIe for mSATA
Full-size Mini PCIe for
PCIe
SMBus
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
Mini PCI Express Slots
The Mini PCI Express slots on the system board are used to install one half and/or full size
Mini PCIe card such as network cards or other cards that comply to the mini PCI Express
specifications into the mini PCI Express slot.
25
Chapter 2 Hardware Installation
21
SMBUS_Alert
SMBUS_CLK
3V3SB
Chapter 2
Front Panel Connector
Pin Pin Assignment
HDD-LED
RESET-SW
6
HDD Power
3
Ground
3
Ground
5
RST Signal
Pin Pin Assignment
PWR Button
PWR LED
Suspend
Mode LED
1 2
Power Button
Reset Button
Power_LED
SUS_LED
5 6
HDD_LED
HDD-LED - HDD LED
This LED will be lit when the hard drive is being accessed.
RESET-SW - Reset Switch
This switch allows you to reboot without having to power off the system.
PWR-BTN - Power Switch
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
26
Chapter 2 Hardware Installation
1
Power Button
3
Ground
2
Power LED
3
Ground
3
Ground
4
SUS LED
Chapter 2
Standby Power LED
Battery
Battery
Ground
1
Battery
Standby
Power LED
This LED will blink when the system is in the standby mode. It indicates that there is power
on the system board. Power-off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
Battery
Connect to the battery connector
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
27
Chapter 2 Hardware Installation
Chapter 3
Chapter 3 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup Defaults
<F10>
Save and Exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
28
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1980 to 2099.
29
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
ACPI Settings
CPU Configuration
This section is used to configure the system ACPI parameters.
This section is used to configure the CPU.
Wake on LAN
Intel(R) SpeedStep(tm)
This field use to enable or disable the LAN signal to wake up the system.
This field is used to enable or disable the Intel Enhanced SpeedStep Technology.
Turbo Mode
After G3
This field is used to enable or disable processor turbo mode.
This field is to specify what state to go when power is re-applied after a power failure
(G3 state).
S0 State
The system working state.
S5 State
System off, except for trickle current to devices such as the power button.
30
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Video Configuration
This section configures the video settings.
Boot display
Set the display device combination. If the board is equipped with an eDP port, the following screen is displayed instead.
Internal Graphics
Keep IGFX enabled or disabled based on the setup options.
Always Enabled PEG
Enable or disable the PEG function.
31
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Audio Configuration
This section is used to configure the audio settings.
HD Audio
Panel Color Depth
Control the detection of the HD-Audio device.
Select the LFP panel color depth: 18 bit, 24 bit, 36 bit, and 48 bit.
Disabled
HD Audio will be unconditionally disabled.
Enabled
HD Audio will be unconditionally enabled.
Auto
HD Audio will be enabled if present and disabled otherwise.
LCD Panel Type
Select the LCD panel type.
32
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
SATA Configuration
This section is designed to select the SATA controller and the type of hard disk drives which
are installed in your system unit.
SATA Mode Selection
SATA Controller(s)
The mode selection determines how the SATA controller(s) operates.
This field is used to enable or disable Serial ATA devices.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
RAID Mode
This option allows you to create RAID or Intel Matrix Storage configuration on Serial ATA
devices.
Serial ATA Port 0, 1, and 2
This field is used to enable or disable the serial ATA port.
33
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
USB Configuration
PCI Express Configuration
This section is used to configure the parameters of the USB device.
This section configures settings relevant to PCI Express root ports.
USB BIOS Support
Disabled
Disable USB keyboard/mouse/storage support.
Enabled
Enable USB keyboard/mouse/storage support under UEFI and DOS environment.
34
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
PCI Express Root Port
PCIe Speed
This field is used to enable or disable the PCI Express Root Port.
Select the speed of the PCI Express Root Port: Auto, Gen1, Gen2 or Gen3.
35
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
ME Configuration
Active Management Technology Support
This section configures settings on flashing Intel ME region.
The section allows users to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Refer to chapter 6 for more information.
Me Fw Image Re-Flash
Intel AMT Support
This field is used to enable or disable flashing the Intel Management Engine region.
This field is used to enable or disable Intel® Active Management Technology BIOS extension.
Un-Configure ME
This field is used to un-configure ME without password.
36
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
SIO NUVOTON6106D
This section configures the system super I/O chip parameters.
CPU Smart Fan Control
COM Port 1 to COM Port 6
Enable or disable the CPU smart fan.
Configure the settings to use the serial port.
Boundary 1 to Boundary 4
Disable No configuration
Enable
o
Set the boundary temperature. The range is from 0-127 C.
Fan Speed Count 1 to Fan Speed Count 4
User configuration
Type
Set the fan speed. The range is from 1-100%.
Choose RS232/RS422/RS485 for the COM port type.
37
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
PC Health Status
This field only displays the PC health status information.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable
WDT. Input any value between 1 to 255.
Case Open
Enable or disable the case open.
AC Power Loss
Set the AC power loss to always off or always on.
38
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Security
TPM Availability
TPM Operation
Set the TPM availability.
Enable or disable TPM function. This option will automatically return to No-Operation.
Clear TPM
Remove all TPM context associated with a specific owner.
39
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Set Supervisor Password
Set the supervisor’s password and the length of the password must be greater than one character.
40
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Boot
Numlock
Select the power-on state for numlock.
Numlock
Boot Type
Select the power-on state for numlock.
Select the boot type. The options are Dual Boot Type, Legacy Boot Type or UEFI Boot
Type.
PXE Boot to LAN
Disable or enable PXE boot to LAN.
USB Boot
Enable or disable booting to USB boot devices.
Note:
If the boot type is set to UEFI, the method for RAID volume creation will be different.
Please refer to Chapter 5 ˗ RAID for more information.
41
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Legacy
This section is used to set legacy boot order.
Normal Boot Menu
Normal
Based on the boot normal priority, it determines the EFI device first or the legacy device
first.
Advance
All boot devices follow the user’s selection sequence.
Boot Type Order
Select the priority of boot type: Normal Boot or Advance Boot.
42
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Exit
Exit Saving Changes
Select this field and then press <Enter> to exit the system setup and save your changes.
Load Optimal Defaults
Select this field and then press <Enter> to load optimal defaults.
Discard Changes
Select this field and then press <Enter>to exit the system setup without saving your
changes.
43
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions about how to
update BIOS with the flash utility.
1. The Intel® Management Engine has already been integrated into this system board. Due to
the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board
and used on another system board of the same model.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing BIOS updating procedure. For your convenience, we
will also provide you with an auto-execution file in the BIOS file downloaded. This auto-execution file will bring you directly to the flash utility menu soon after system boots up and finishes
running the boot files in your boot disk.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
RRead file successfully.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
(path= “platform.ini”)
Information
Please do not remove the AC power
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: SU25x
New BIOS Model name: SU25x
Current BIOS version: 68.08A
New BIOS version: 68.08A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\SU25x>_
100%
100%
44
Chapter 3 BIOS Setup
www.dfi.com
Chapter 4
Chapter 4 - Supported Software
For Windows 8.1
Install drivers, utilities and software applications that are required to facilitate and enhance the
performance of the system board. You may acquire the software from your sales representatives, from an optional DVD included in the shipment, or from the website download page at
https://www.dfi.com/DownloadCenter.
For Windows 10
45
Chapter 4 Supported Software
www.dfi.com
Chapter 4
For Windows 7
Intel Chipset Software Installation Utility
The Intel Chipset Software Installation Utility is used for updating Windows® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Software Installation Utility” on the main menu.
1. Setup is ready to install the
utility. Click Next.
2. Read the license agreement
then click Yes.
Note:
This step can be ignored if the applications are standalone files.
46
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Graphics Drivers
3. Go through the readme
document for more installation tips then click Next.
To install the driver, click “Intel Graphics Drivers” on the main menu.
1. Setup is now ready to
install the graphics driver.
Click Next.
4. Click Finish to exit setup.
By default, the “Automatically run WinSAT and enable the Windows Aero
desktop theme” is enabled. With this enabled, after installing the graphics
driver and the system rebooted, the screen will turn blank for 1 to 2 minutes
(while WinSAT is running) before the Windows 7/Windows 8.1/Windows 10
desktop appears. The “blank screen” period is the time Windows is testing
the graphics performance.
2. Read the license agreement
then click Yes.
47
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Audio Drivers
3. Go through the readme
document for system requirements and installation
tips then click Next.
To install the driver, click “Audio Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
4. Setup is now installing the
driver. Click Next to continue.
2. Click “Yes, I want to restart
my computer now” then
click Finish.
Restarting the system will
allow the new software
installation to take effect.
5. Click “Yes, I want to restart
this computer now” then
click Finish.
Restarting the system will
allow the new software
installation to take effect.
48
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel LAN Drivers
4. Click Install to begin the
installation.
To install the driver, click “Intel LAN Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
5. After completing installation, click Finish.
2. Click “I accept the terms
in the license agreement”
then click “Next”.
3. Select the program featuers
you want installed then
click Next.
49
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Kernel Mode Driver Framework (For Windows 7 only)
3. Click “Restart Now“ to
restart your computer when
the installation is complete.
To install the driver, click “Kernel Mode Driver Framework” on the main menu.
1. Click “Yes“ to install the
update.
2. The update is installed
now.
50
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Management Engine Drivers
3. Setup is currently installing
the driver. After installation
has completed, click “Next”.
To install the driver, click “Intel Management Engine Drivers” on the main menu.
1. Setup is ready to install the
driver. Click “Next”.
4. Please wait while the product is being installed.
2. Read the license agreement
then click “Next”.
5. After completing installation, click “Finish”.
51
Chapter 4 Supported Software
www.dfi.com
Chapter 4
HW Utility
3. Read the license agreement
then click “I accept the terms
in the license agreement”.
Click “Next”.
HW Utility provides information about the board, Watchdog, and DIO. To access the utility,
click “HW Utility” on the main menu.
Note:
If you are using Windows 7 or later versions, you need to access the operating system as an administrator to be able to install the utility.
1. Setup is ready to install the
driver.
4. The wizard is ready to begin
installation. Click “Install”.
2. Click “Next” to continue.
5. Please wait while the program
features are being installed.
52
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel USB 3.0 Drivers (For Windows 7 and Windows 8.1)
6. After completing installation, click “Finish”.
To install the driver, click “Intel USB 3.0 Driver” on the main menu.
1. Setup is ready to install the driver.
Click Next.
The HW Utility icon will appear on the desktop. Double-click the icon to open the utility.
2. Read the license agreement then
click Yes.
SU251
Intel(R) Core(TM) i7-6600U CPU @ 2.60GHz
3949 MBytes
Information
Note:
Note: The screenshot displayed above is for illustrative purpose only, and may not
resemble the actual screen.
The SU251 HW Utility features the following tabs: Information, HW Health, HW Health set,
Watchdog, DIO and Backlight. Click on the tabs to access information about the board.
53
Chapter 4 Supported Software
www.dfi.com
Chapter 4
IO Driver (For Windows 10 and Windows 8.1)
3. Go through the readme document for more installation tips
then click Next.
To install the driver, click “Intel Serial IO Driver” on the main menu
1. Setup is ready to install the driver.
Click Next.
4. Setup is currently installing the
driver. After installation has completed, click Next.
2. Read the license agreement carefully. Click “I accept the terms in
the License Agreement” then
click Next.
5. After completing installation, click
Finish.
54
Chapter 4 Supported Software
www.dfi.com
Chapter 4
3. Read the file information then click
Next.
5. Setup is now installing the
driver.
4. Setup is ready to install the driver.
Click Next.
6. Click Finish.
55
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Microsoft Framework 4.5.2 (For Windows 7)
3. Setup is now installing the
driver.
Note:
Before installing Microsoft Framework 4.5.2, make sure you have updated your
Windows 7 operating system to Service Pack 1.
To install the driver, click “Microsoft Framework 4.5.2” on the main menu.
1. Setup is now extracting files.
4. Click “Finish”.
2. Read the license agreement carefully.
Click “I have read and accept
the terms of the License Agree
ment” then click “Install”.
56
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Rapid Storage Technology
Infineon TPM 1.2 Driver and Tool (Optional)
The Intel Rapid Storage Technology is a utility that allows you to monitor the current status
of the SATA drives. It enables enhanced performance and power management for the storage
subsystem.
To install the driver, click “Infineon TPM driver and tool (option)” on the main menu.
1. The setup program is preparing
to install the driver.
To install the driver, click “Intel Rapid Storage Technology” on the main menu. Please refer to
Chapter 5 for more information.
2. The setup program is now ready
to install the utility. Click “Next”.
3. Click “I accept the terms in the
license agreement” and then
click “Next”.
57
Chapter 4 Supported Software
www.dfi.com
Chapter 4
4. Enter the necessary information
and then click “Next”.
7. TPM requires installing the Microsoft Visual C++ package prior to
installing the utility. Click “Install”.
5. Select a setup type and then click
“Next”.
8. The setup program is currently
installing the Microsoft Visual
C++ package.
9. Click “Finish”.
6. Click “Install”.
58
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Adobe Acrobat Reader 9.3
10. Click “Yes” to restart your system.
To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.
1. Click Next to install or click
Change Destination Folder
to select another folder.
2. Click Install to begin installation.
3. Click Finish to exit installation.
59
Chapter 4 Supported Software
www.dfi.com
Chapter 5
Chapter 5 - RAID
Settings
The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1,
and RAID 5.
To enable the RAID function, the following settings are required.
1. Connect the Serial ATA drives.
RAID Levels
2. Enable Serial ATA in the Insyde BIOS.
RAID 0 (Striped Disk Array without Fault Tolerance)
3. Create a RAID volume.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk
drives. This improves the I/O performance of the drives at different channel; however it is not
fault tolerant. A failed disk will result in data loss in the disk array.
4. Install the Intel Rapid Storage Technology Utility.
Step 1: Connect the Serial ATA Drives
RAID 1 (Mirroring Disk Array with Fault Tolerance)
Refer to chapter 2 for details on connecting the Serial ATA drives.
RAID 1 copies and maintains an identical image of the data from one drive to the other drive.
If a drive fails to function, the disk array management software directs all applications to the
other drive since it contains a complete copy of the drive’s data. This enhances data protection
and increases fault tolerance to the entire system. Use two new drives or an existing drive and
a new drive but the size of the new drive must be the same or larger than the existing drive.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID BIOS utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
RAID 5
RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides
better hard drive performance and more storage capacity.
Step 2: Enable RAID in the BIOS
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
2. Go to “Advanced” menu, and select the “SATA Configuration” menu.
3. Change the “SATA Mode Selection” to “RAID” mode.
4. Save the changes in the “Save & Exit” menu.
5. Reboot the system.
60
Chapter 5 RAID
www.dfi.com
Chapter 5
Step 3: Create a RAID Volume
Step 3-1: Create a RAID Volume if the boot type is UEFI
1. When the Intel RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
If the boot type is set to UEFI, RAID volume creation will be different. Please use the following
steps to create RAID volumes. To set the boot type, enter the Insyde BIOS and go to “Boot”
>”Boot type”.
®
2. Select 1: Create RAID Volume and press <Enter>.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
1. Go to the “Advanced” menu of the Insyde BIOS.
4. Use the up or down arrow keys to select the strip size and press <Enter>.
2. The “Intel® Rapid Storage Technology” menu appears. Enter this menu.
5. Press <Enter> to select the physical disks.
6. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
7. Press <Enter>.
8. Select the volume size and press <Enter>. You must select less than one hundred percent
of the available volume space to leave space for the second volume.
9. Press <Enter> to create the volume.
10. At the prompt, press <Y> to confirm volume creation.
11. Select 4: Exit and press <Enter>.
12. Press <Y> to confirm exit.
Note:
These steps are cited from the Intel® Suppot site, “Set Up a System with Intel®
Matrix RAID Technology” (Article ID: 000005789).
http://www.intel.com/content/www/us/en/support/boards-and-kits/000005789.htm
3. The screen displays all available drives. Select “Create RAID volume” to create a RAID
volume”.
4. Use the up or down arrow keys to select the RAID level and press <Enter>.
5. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
6. Press <Enter>.
7. Use the up or down arrow keys to select the strip size and press <Enter>.
8. Enter the volume size and press <Enter>.
9. At the prompt, press <Y> to confirm volume creation.
61
Chapter 5 RAID
www.dfi.com
Chapter 5
Step 4: Install the Intel Rapid Storage Technology Utility
5. Go through the readme
document to view system
requirements and installation information then click
Next.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/
or SATA drives. It enables enhanced performance and power management for the storage
subsystem.
1. Insert the provided DVD into an optical drive.
2. Click “Intel Rapid Storage Technology Utility” on the main menu.
3. Setup is ready to install
the utility. Click Next.
6. Click Next to install to
the default folder or click
change to choose another
destination folder.
4. Read the license agreement and click “I accept
the terms in the License
Agreement.“ Then, click
Next.
7. Confirm the installation and
click Next.
62
Chapter 5 RAID
www.dfi.com
Chapter 5
8. Click “Yes, I want to restart
this computer now” to
complete the installation
and then click Finish.
63
Chapter 5 RAID
www.dfi.com
Chapter 6
Chapter 6 - Intel AMT Settings
Enable Intel® AMT in the Insyde BIOS
Overview
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
Intel Active Management Technology (Intel AMT) combines hardware and software solution to
provide maximum system defense and protection to networked systems.
2. In the Advanced menu, select Avtive Management Technology Support.
®
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
• Discover
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
• Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
3. In the Advanced menu, select Enabled for the AMT Support option.
Un-Configure ME
Un-configure ME without password. You can select enabled or disabled.
64
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
Enable Intel® AMT in the Intel® Management
Engine BIOS Extension (MEBX) Screen
4. In the Exit menu, select Exit Saving Changes then select OK.
1. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password
then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
65
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
2. Enter a password in the space provided under Intel(R) ME Password then press Enter. The
password must include:
•
•
•
•
•
3. You will be asked to verify the password. Enter the same new password in the space provided under Verify Password then press Enter.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
Intel(R) ME Password
4. Select Intel(R) ME General Settings then press Enter.
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
66
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
5. Select Change Intel(R) ME Password then press Enter.
6.Select Local FW Update then press Enter. Select Enabled or Disabled or password
Protected then press Enter.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under Intel(R) ME New Password then press Enter.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
Disabled
Enabled
Password Protected
<Enabled>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
7. Select Previous Menu until you return to the Main Menu. Select Intel(R) AMT Configuration then press Enter.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
[Esc]= Exit
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
67
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
8.In the Intel(R) AMT Configuration menu, select Manageability Feature Selection
then press Enter. Select Enabled or Disabled then press Enter.
10. In the SOL/Storage Redirection/KVM menu, select Username and Password then
press Enter. Select Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved..
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9.In the Intel(R) AMT Configuration menu, select SOL/Storage Redirection/KVM
then press Enter.
11. In the SOL/Storage Redirection/KVM menu, select SOL then press Enter. Select
Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
Menu for FW Redirection Configuration
[↑↓] = Move Highlight
< Enabled>
<Enabled>
<Enabled>
<Enabled>
[Esc]= Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
68
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
12. In the SOL/Storage Redirection/KVM menu, select Storage Redirection then press
Enter. Select Enabled or Disabled then press Enter.
14. Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select
User Consent then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
User Opt-in
Opt-in Configurable from Remote IT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< KVM>
< Enabled>
Disabled
Enabled
Configure When User Consent Should be Required.
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
13. In the SOL/IDER/KVM menu, select KVM Feature Selection then press Enter. Select
Enabled or Disabled then press Enter.
[Esc]= Exit
15. In the User Consent menu, select User Opt-in then press Enter. Select None or KVM
or ALL then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
69
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
16. In the User Consent menu, select Opt-in Configurable from Remote IT then press
Enter. Select Enabled or Disable Remote Control of KVM Opt-in Policy then press
Enter.
18. In the Intel(R) AMT Configuration menu, select Network Setup then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< KVM>
< Enabled>
Disabled
Enabled
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
19. In the Intel(R) ME Network Setup menu, select Intel(R) ME Network Name Settings then press Enter.
17. Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select
Password Policy then press Enter.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Intel (R) ME Network Name Settings
> TCP/ IP Settings
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Step And Configuration
Anytime
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
70
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
20. In the Intel(R) ME Network Name Settings menu, select Host Name then press
Enter. Enter the computer’s host name then press Enter.
22. Select Shared/Dedicated FQDN then press Enter. Select Shared or Dedicated then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Host Name
[Enter] = Complete Entry
Dedicated
Shared
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc]= Discard Changes
21. Select Domain Name then press Enter. Enter the computer’s domain name then press
Enter.
23. Select Dynamic DNS Update then press Enter. Select Enabled or Disabled then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Domain Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
_
_
<Shared>
<Disabled>
Disabled
Enabled
[Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
71
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
26. In the Intel(R) AMT Configuration menu, select Activate Network Access then
press Enter.
24. Select Previous Menu until you return to the Intel(R) ME Network Setup menu. Select
TCP/IP Settings then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
TCP/ IP SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Wired LAN IPV4 Configuration
[↑↓] = Move Highlight
[Enter] = Select Entry
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[Esc]= Exit
<Anytime>
<Full Unprovision>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
25. In the TCP/IP Settings menu, select Wired LAN IPV4 Configuration then press
Enter.
27. In the Intel(R) AMT Configuration menu, select Unconfigure Network Access then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
< Enabled>
<Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
< Enabled>
<Anytime>
<Full Unprovision>
Full Unprovision
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
72
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
28. In the Intel(R) AMT Configuration menu, select Remote Setup And Configuration
then press Enter.
30. In the Intel(R) Remote Setup And Configuration menu, select Provisioning Record then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
< Enabled>
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
<Anytime>
<Full Unprovision>
_
_
Provision Record is not present
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
29. In the Intel(R) Remote Setup And Configuration menu, select Current Provisioing
Mode then press Enter.
[Esc]= Exit
31. In the Intel(R) Remote Setup And Configuration menu, select Provisioning server
IPV4/IPV6, enter the Provisioning server address then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
Provisioning Mode:PKI
_
_
Provisioning server address
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
73
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
32. In the Intel(R) Remote Setup And Configuration menu, select Provisioning server
FQDN, enter the FQDN of Provisioning server then press Enter.
34. In the Intel(R) Remote Setup And Configuration menu, select TLS PKI then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
35. In the Intel(R) Remote Configuration menu, select Remote Configuration**
then press Enter, select Enabled or Disabled then press Enter.
33. In the Intel(R) Remote Setup And Configuration menu, select RCFG then press
Enter, and select Start Configuration then press enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
< Enabled>
_
Disabled
Enabled
[ESC] = Exit
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[↑↓] = Move Highlight
[Esc]= Exit
[Enter] = Select Entry
[Esc]= Exit
74
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
36. Select PKI DNS Suffix, Enter the PKI DNS Suffix then press Enter.
38. In the Intel(R) AMT Configuration menu, select Power Control then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
_
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[↑↓] = Move Highlight
[Esc]= Exit
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
39. In the Intel(R) AMT Power Control menu, select Intel(R) AMT ON in Host Sleep
States then press Enter. Select an option then press Enter.
37. Select Manage Hashes then press Enter, and select one of hash name.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
These configurations are effective only after AMT provisioning has started
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
< Enabled>
Intel (R) AMT ON in Host Sleep States
< Enabled>
_
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Mobile: ON in S0
Mobile: ON in S0, ME Wake in S3, S4-5 (AC only)
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
75
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
40. In the Intel(R) AMT Power Control menu, select Idle Timeout then press Enter.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
<ENTER> = Complete Entry
[ESC]= Discard Changes
41. Select Previous Menu until you return to the Main Menu. Select Exit then press Enter.
Type Y then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
76
Chapter 6 Intel AMT Settings
www.dfi.com
Appendix A
Appendix A - Troubleshooting Checklist
The picture seems to be constantly moving.
Troubleshooting Checklist
1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.
This chapter of the manual is designed to help you with problems that you may encounter
with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple
causes.
2. Move away any objects, such as another monitor or fan, that may be creating a magnetic
field around the display.
Some of the most common things to check when you encounter problems while using your
system are listed below.
The screen seems to be constantly wavering.
3. Make sure your video card’s output frequencies are supported by this monitor.
1. The power switch of each peripheral device is turned on.
1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off.
Fluorescent lights adjacent to the monitor may also cause screen wavering.
2. All cables and power cords are tightly connected.
Power Supply
3. The electrical outlet to which your peripheral devices are connected is working. Test the
outlet by plugging in a lamp or other electrical device.
When the computer is turned on, nothing happens.
4. The monitor is turned on.
1. Check that one end of the AC power cord is plugged into a live outlet and the other end
properly plugged into the back of the system.
5. The display’s brightness and contrast controls are adjusted properly.
2. Make sure that the voltage selection switch on the back panel is set for the correct type of
voltage you are using.
6. All add-in boards in the expansion slots are seated securely.
3. The power cord may have a “short” or “open”. Inspect the cord and install a new one if
necessary.
7. Any add-in board you have installed is designed for your system and is set up correctly.
Monitor/Display
Floppy Drive
If the display screen remains dark after the system is turned on:
The computer cannot access the floppy drive.
1. Make sure that the monitor’s power switch is on.
1. The floppy diskette may not be formatted. Format the diskette and try again.
2. Check that one end of the monitor’s power cord is properly attached to the monitor and
the other end is plugged into a working AC outlet. If necessary, try another outlet.
2. The diskette may be write-protected. Use a diskette that is not write-protected.
3. Check that the video input cable is properly attached to the monitor and the system’s
display adapter.
3. You may be writing to the wrong drive. Check the path statement to make sure you are
writing to the targeted drive.
4. Adjust the brightness of the display by turning the monitor’s brightness control knob.
4. There is not enough space left on the diskette. Use another diskette with adequate storage
space.
77
Appendix A Troubleshooting Checklist
www.dfi.com
Appendix A
Hard Drive
System Board
Hard disk failure.
1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is
loose, power off the system, re-install the card and power up the system.
1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS.
2. Check the jumper settings to ensure that the jumpers are properly set.
2. If the system is configured with two hard drives, make sure the bootable (first) hard drive
is configured as Master and the second hard drive is configured as Slave. The master hard
drive must have an active/bootable partition.
3. Verify that all memory modules are seated securely into the memory sockets.
4. Make sure the memory modules are in the correct locations.
Excessively long formatting period.
5. If the board fails to function, place the board on a flat surface and seat all socketed components. Gently press each component into the socket.
If your hard drive takes an excessively long period of time to format, it is likely a cable connection problem. However, if your hard drive has a large capacity, it will take a longer time to
format.
6. If you made changes to the BIOS settings, re-enter setup and load the BIOS defaults.
Serial Port
The serial device (modem, printer) doesn’t output anything or is outputting garbled
characters.
1. Make sure that the serial device’s power is turned on and that the device is on-line.
2. Verify that the device is plugged into the correct serial port on the rear of the computer.
3. Verify that the attached serial device works by attaching it to a serial port that is working
and configured correctly. If the serial device does not work, either the cable or the serial
device has a problem. If the serial device works, the problem may be due to the onboard
I/O or the address setting.
4. Make sure the COM settings and I/O address are configured correctly.
Keyboard
Nothing happens when a key on the keyboard was pressed.
1. Make sure the keyboard is properly connected.
2. Make sure there are no objects resting on the keyboard and that no keys are pressed during the booting process.
78
Appendix A Troubleshooting Checklist
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising