Dfi SU171/SU173 Manual
SU171/SU173
Mini-ITX Industrial Motherboard
User’s Manual
A38930952
1
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2018. All Rights Reserved.
Notice:
Trademarks
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2
Table of Contents
Audio ...................................................................................... 20
I/O Connectors ...................................................................... 20
Digital I/O Connector ................................................................ 20
Digital I/O Power Connector ...................................................... 20
SATA (Serial ATA) Connectors .................................................... 21
SATA (Serial ATA) Power Connectors .......................................... 21
COM (Serial) Ports ................................................................... 22
Front Panel Connector .............................................................. 23
Cooling Fan Connectors............................................................. 23
LVDS LCD Panel Connector ........................................................ 24
LCD/Inverter Power Connector ................................................... 24
S/PDIF Connector..................................................................... 25
SMBus Connector ..................................................................... 25
Expansion Slots ....................................................................... 26
Chassis Intrusion Connector ...................................................... 26
eDP Connector (Optional).......................................................... 27
LPC Connector ......................................................................... 28
Standby Power LED .................................................................. 29
Battery ................................................................................... 29
Copyright................................................. 2
Trademarks .............................................. 2
FCC and DOC Statement on Class B ......... 2
About this Manual .................................... 4
Warranty ................................................. 4
Static Electricity Precautions ..................... 4
Safety Measures....................................... 4
Chapter 3 - BIOS Setup ..........................30
About the Package ................................... 5
Overview ............................................................................... 30
Insyde BIOS Setup Utility ....................................................... 31
Main ....................................................................................... 31
Advanced ................................................................................ 31
Security .................................................................................. 40
Boot ....................................................................................... 42
Exit ........................................................................................ 44
Chapter 1 - Introduction........................... 6
Specifications...........................................................................6
Features ..................................................................................7
Updating the BIOS ................................................................. 44
Notice: BIOS SPI ROM ........................................................... 45
Chapter 2 - Hardware Installation ............. 9
Chapter 4 - Supported Software ..............46
Board Layout ...........................................................................9
System Memory .......................................................................9
Chapter 5 - RAID ....................................62
Installing the DIMM Module ....................................................... 10
Jumper Settings ..................................................................... 11
Chapter 6 - Intel AMT Settings ................65
Clear CMOS Data ..................................................................... 11
Auto Power-on Select ............................................................... 12
LVDS Panel Power Select........................................................... 12
LCD/Inverter Power Select ........................................................ 13
LVDS Backlight Power Select ..................................................... 13
eDP Panel Power Select (Optional) ............................................. 14
eDP Inverter Power Select (Optional) ......................................... 14
eDP Backlight Power Select (Optional) ........................................ 15
COM 1/COM 2 RS232/Power Select ............................................ 15
Mini PCIe/mSATA Signal Select .................................................. 16
Appendix A - Troubleshooting Checklist ....78
Rear Panel I/O Ports .............................................................. 17
12V DC-in (SU171)/15~36V DC-in (SU173) ................................ 17
Graphics Interfaces .................................................................. 18
RJ45 LAN Ports ........................................................................ 18
USB Ports................................................................................ 19
3
About this Manual
Static Electricity Precautions
This manual can be downloaded from the website, or acquired as an electronic file included in
the optional CD/DVD. The manual is subject to change and update without notice, and may
be based on editions that do not resemble your actual products. Please visit our website or
contact our sales representatives for the latest editions.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
2. Wear an antistatic wrist strap.
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
4
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
•
•
•
•
One
One
One
One
SU171/SU173 motherboard
COM port cable (Length: 250mm, 1 x COM port)
Serial ATA data with power cable (Length: 300mm)
Heat sink (Height: 25mm)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
•
•
•
•
•
•
•
•
•
•
USB port cable (Length: 200mm)
COM port cable (Length: 250mm, 1 x COM port)
Serial ATA data with power cable (Length: 300mm)
Power adapter (100W, 12V, Level 6)
Power adapter (120W, 19V)
LPC EXT-RS232 module (4 x RS232 ports)
LPC EXT-RS485 module (4 x RS485 ports)
I/O shield
Half height I/O shield
DT122 Chassis
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
•
•
Memory module
Storage devices such as hard disk drive, DVD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1
Chapter 1 - Introduction
Specifications
SYSTEM
GRAPHICS
Processor
6th Generation Intel® CoreTM Processors, BGA 1356
Intel® CoreTM i7-6600U Processor, Dual Core, 4M Cache, 2.6GHz (3.4GHz), 15W
Intel® CoreTM i5-6300U Processor, Dual Core, 3M Cache, 2.4GHz (3.0GHz), 15W
Intel® CoreTM i3-6100U Processor, Dual Core, 3M Cache, 2.3GHz, 15W
Intel® Celeron® Processor 3955U, Dual Core, 2M Cache, 2.0GHz, 15W
Memory
Two 204-pin SODIMM up to 16GB
Dual Channel DDR3L 1600MHz
BIOS
Insyde SPI 128Mbit
Controller
Intel® HD Graphics GT Series
Feature
OpenGL 4.4, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9
Display
Triple
Displays
EXPANSION Interface
1 x LVDS/eDP (eDP available upon request)
1 x HDMI/DP (DP available upon request)
1 x DP++
LVDS: dual channel 48-bit, resolution up to 1920x1200 @ 60Hz
DP: resolution up to 4096x2304 @ 60Hz
HDMI: resolution up to 2560x1600 @ 60Hz or 4096x2160 @ 24Hz
x
x
x
x
PCIe x4 (Gen 3)
SIM (available upon request)
Full-size Mini PCIe (PCIe/USB/SATA)
Full-size Mini PCIe (PCIe/USB)
AUDIO
Audio
Codec
Realtek ALC888S-VD2-GR
ETHERNET
Controller
1 x Intel® I210AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps) (only Core i7/i5 supports iAMT)
REAR I/O
Ethernet
2 x GbE (RJ-45)
USB
4 x USB 3.0
Display
1 x HDMI/DP (DP available upon request)
1 x DP++
Audio
1 x Line-out
1 x Mic-in
Serial
2 x RS-232/422/485 (RS-232 w/ power) (2.0mm pitch)
2 x RS-232 (2.0mm pitch)
USB
4 x USB 2.0 (2.0mm pitch) or
2 x USB 2.0 (2.0mm pitch) + 1 x Vertical USB 2.0 (type A) (available upon request)
Display
1 x LVDS LCD Panel Connector
1 x LCD/Inverter Power
1 x eDP LCD Panel Connector (available upon request)
INTERNAL
I/O
1 x S/PDIF
SATA
2 x SATA 3.0 (up to 6Gb/s)
2 x SATA Power
RAID 0/1/5
DIO
1 x 8-bit DIO
LPC
1 x LPC (supports LPC EXT-RS232/RS485 module)
SMBus
1 x SMBus
WATCHDOG
TIMER
Output &
Interval
System Reset, Programmable via Software from 1 to 255 Seconds
SECURITY
TPM
Available Upon Request
POWER
Type
Single 12V +/-10% DC (SU171)
Wide Range 15~36V (SU173)
Connector
DC-in Jack
Right Angle Connector (4-pin) (available upon request)
Vertical Type Connector (4-pin) (available upon request)
Consumption
SU171
Typical: 6600U:12V @ 0.98A (11.76Watt); 6300U:12V @ 0.95A (11.40Watt)
Max: 6600U:12V @ 1.62A (19.44Watt); 6300U:12V @ 1.58A (18.96Watt)
SU173
Typical: 6600U:19V @ 0.48A (9.12Watt); 6300U:19V @ 0.43A (8.170Watt)
Max: 6600U:19V @ 1.05A (19.95Watt); 6300U:19V @ 0.90A (17.10Watt)
RTC Battery
Lithium 3V (210mAH)
OS SUPPORT
Microsoft
/Linux
Windows 7 (/WES7) 32/64-bit
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise 64-bit
Debian 8 (with VESA graphic driver)
CentOS 7 (with VESA graphic driver)
Ubuntu 15.10 (Intel graphic driver available)
ENVIRONMENT
Temperature
Operating: 0 to 60°C / -20 to 70°C
Storage: -40 to 85°C
Humidity
Operating: 5 to 90% RH
Storage: 5 to 90% RH
MTBF
SU171 : 357,691 hrs @ 25°C; 206,450 hrs @ 45°C ; 130,229 hrs @ 60°C
SU173 : 347,511 hrs @ 25°C; 200,230 hrs @ 45°C ; 126,434 hrs @ 60°C
Calculation model: Telcordia Issue 2, Method I Case 3
Environment: GB, GC – Ground Benign, Controlled
Dimensions
Mini-ITX Form Factor
170mm (6.7") x 170mm (6.7")
Height
PCB: 1.6mm
Top Side: 16.5mm, Bottom Side: 3.5mm
LVDS + HDMI + DP++
LVDS + DP + DP++ (available upon request)
eDP + HDMI + DP++ (available upon request)
eDP + DP + DP ++ (available upon request)
1
1
1
1
Audio
MECHANICAL
CERTIFICATIONS
CE, FCC Class B, RoHS
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Features
• Wake-On-LAN
• Watchdog Timer
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCIe LAN card that uses the PCIe PME (Power
Management Event) signal. However, if your system is in the Suspend mode, you can poweron the system only through an IRQ or DMA interrupt.
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• DDR3L
DDR3L is a higher performance DDR3 SDRAM interface providing less voltage and higher
speed successor. DDR3L SDRAM modules support 1600MHz for DDR modules. DDR3L delivers
increased system bandwidth and improved performance to provide its higher bandwidth and its
increase in performance at a lower power.
• Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
• Graphics
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications. Supports 1 LVDS/eDP, 1 HDMI/
DP and 1 DP++ interface for triple display outputs.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the 5V_standby power source of your power supply must support ≥2A.
• PCI Express
• RTC Timer
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes.
The RTC installed on the system board allows your system to automatically power-on on the
set date and time.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s.
• Gigabit LAN
Intel® I210AT PCI Express Gigabit Ethernet and Intel® I219LM with iAMT11.0 Gigabit Ethernet
Phy controllers support up to 1Gbps data transmission.
7
Chapter 1 Introduction
www.dfi.com
• ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to go
through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
• USB
The system board supports the new USB 3.0. It is capable of running at a maximum transmission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement in
device transfer speeds between your computer and a wide range of simultaneously accessible
external Plug and Play peripherals.
8
Chapter 2
Chapter 2 - Hardware Installation
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Board Layout
4-pin
Right Angle
(optional)
LVDS LCD Panel
40
DC-in
2
39
1
LVDS Panel Power 6
Select (JP13)
4-pin Vertical Type (optional)
5
2
1
PTN3460
1
LPC
eDP
(optional)
2
29
30
1
6
2
eDP Inverter
1
Power Select (JP18)
(optional)
1
eDP Backlight Power
Select (JP17) (optional)
HDMI/DP
LCD/Inverter
Power Select (JP14)
SMBus
LCD/Inverter
Power
1
CPU Fan
1
SPI Flash BIOS
2
1
1
1
LVDS Backlight
Power Select (JP12)
LAN 2
DDR3L_1 SODIMM
Intel
Intel
WGI210AT
USB 1-2 USB 3.0
Digital
I/O
6
5
Important:
When the Standby Power LED lights red, it indicates that there is power on the
system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
1
Digital I/O
Power
MP2939
LAN 1
System Memory
1
1
2
13
14
eDP Panel Power
Select (JP19) (optional)
DDR3L_2 SODIMM
1
DP++
5
System
Fan 2
DDR3L-2
BGA 1356
USB 3-4 USB 3.0
SATA 3.0
1
Line-out
SATA 0
1
SATA 2
2
1
1
Standby
Power LED
PCIe 1 (PCIe x4)
4
1
1
4
10 2
9 1
USB 9-10
USB 2.0
Buzzer
Mini PCIe/mSATA
Signal Select (JP7)
1
11
12
1 2
1
1
2
1
Front Panel
SATA
Power 2
Mini PCIe
S/PDIF
Mic-in
Clear CMOS Data
(JP1) 1
SATA
Power 0
DDR3L-1
System
Fan 1
Auto Power-on
Select (JP16)
Battery
Mini PCIe
10
9
USB 7-8
Chassis
Intrusion
1
2
6
2
6
1
5
1
5
COM 1 RS232/Power
Select (JP4)
COM 2 RS232/Power
Select (JP5)
2
10 2
1
COM 1
9 1
10 2
COM 2
9 1
10 2
COM 3
9 1
Standby
Power LED
10
COM 4
9
Features
•
SU171: Single 12V +/-10% DC
SU173: Wide Range 15~36V
•
The eDP connector is optional. Please contact your sales representative for more information.
•
JP17, JP18 and JP19 will work when the eDP connector is populated on the system board.
•
Two 204-pin DDR3L SODIMM sockets
•
Supports 1600MHz DDR3L SDRAM
•
Supports up to 16GB system memory
•
Supports dual channel memory interface
9
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
The system board supports the following memory interface.
Installing the SODIMM Module
Single Channel (SC)
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
Data will be accessed in chunks of 64 bits (8B) from the memory channels.
Dual Channel (DC)
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
Single Channel
Dual Channel
2. Disconnect all power cords and cables.
3. Locate the SODIMM socket on the system board.
DIMMs are on the same channel.
DIMMs in a channel can be identical or
completely different. However, we highly
recommend using identical DIMMs.
Not all slots need to be populated.
4. Note the key on the socket. The key ensures the module can be plugged into the socket in
only one direction.
DIMMs of the same memory configuration
are on different channels.
10
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Jumper Settings
5. Grasping the module by its edges, align the module into the socket at an approximately 30
degrees angle. Apply firm even pressure to each end of the module until it slips down into
the socket. The contact fingers on the edge of the module will almost completely disappear
inside the socket.
Clear CMOS Data
1 2 3
1-2 On:
Normal (default)
6. Push down the module until the clips at each end of the socket lock into position. You will
hear a distinctive “click”, indicating the module is correctly locked into position.
JP1
1 2 3
2-3 On:
Clear CMOS Data
Clip
Clip
If you encounter the following,
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
you can reconfigure the system with the default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
1. Power-off the system and unplug the power cord.
2. Set JP1 pins 2 and 3 to On. Wait for a few seconds and set JP1 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
11
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Auto Power-on Select
LVDS Panel Power Select
JP13
5
3
1
1-2 On: +12V
1
2
3
6
4
2
1-2 On:
Power-on via power button
(default)
JP16
6
4
2
5
3
1
3-4 On: +5V
6
4
2
1
2
3
5
3
1
5-6 On: +3.3V
(default)
2-3 On:
Power-on via AC power
JP16 is used to select the method of powering on the system. If you want the system to
power-on whenever AC power comes in, set JP16 pins 2 and 3 to On. If you want to use the
power button, set pins 1 and 2 to On.
JP13 is used to select the power supplied with the LVDS LCD panel.
Important:
Before powering-on the system, make sure that the power settings of JP13 match
the LCD panel’s specification. Selecting the incorrect voltage will seriously damage the
LCD panel.
When using the JP16 “Power On” feature to power the system back on after a power failure
occurs, the system may not power on if the power lost is resumed within 5 seconds (power
flicker).
12
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LCD/Inverter Power Select
LVDS Backlight Power Select
3 2 1
3 2 1
JP14
JP12
1-2 On: +12V
(default)
1-2 On: +3.3V
(default)
3 2 1
3 2 1
2-3 On: +5V
2-3 On: +5V
JP14 is used to select the power level of the LCD/Inverter power connector.
JP12 is used to select the power level of backlight control: +3.3V (default) or +5V.
Important:
Before powering-on the system, make sure that the power settings of JP12 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
13
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
eDP Panel Power Select (Optional)
eDP Inverter Power Select (Optional)
5 3 1
3 2 1
6 4 2
1-2 On: +12V
JP19
1-2 On: +12V
(default)
JP18
5 3 1
3 2 1
6 4 2
3-4 On: +5V
2-3 On: +5V
5 3 1
6 4 2
5-6 On: +3.3V
(default)
JP18 is used to select the power level of the eDP Inverter power supply.
JP19 is used to select the power supplied with the eDP panel.
Important:
Before powering-on the system, make sure that the power settings of JP19 match
the eDP panel’s specification. Selecting the incorrect voltage will seriously damage the
eDP panel.
14
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
eDP Backlight Power Select (Optional)
3 2 1
COM 1/COM 2 RS232/Power Select
JP17
1-2 On: +3.3V
(default)
3 2 1
2-3 On: +5V
COM 2
COM 1/COM 2:
RS232/422/485
2
1
COM 1
9
JP4 JP5
2 4 6
JP17 is used to select the power level of backlight control: +3.3V (default) or +5V.
2 4 6
1 3 5
1-3 (RI-), 2-4 (DCD-) On:
RS232 (default)
Important:
Before powering-on the system, make sure that the power settings of JP17 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
1 3 5
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
JP4 (for COM 1) and JP5 (for COM 2) are designed to configure Serial COM ports to pure
RS232 or RS232 with power.
RS232
2
1
DATANC.
NC.
NC.
9
RS422
Full Duplex
2
1
9
DATA+
NC.
GND
NC.
NC.
DCDTXD
GND
RTSRI-
9
RXD+
TXD+
GND
NC.
NC.
2
1
RXDTXDNC.
NC.
RXD
DTRDSRCTS-
COM 1/COM 2
RS485
15
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Mini PCIe/mSATA Signal Select
1
2
3
1-2 On: mSATA (default)
1
2
3
JP7
2-3 On: Mini PCIe
JP7 is used to select the Mini PCIe signal: Mini PCIe or mSATA (default).
16
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Rear Panel I/O Ports
12V DC-in (SU171)/15~36V DC-in (SU173)
DC-in
LAN 1 LAN 2
DC-in
HDMI/DP
DP++
USB 3.0
Mic-in
Line-out
The rear panel I/O ports consist of the following:
•
•
•
•
•
•
•
•
1
1
1
1
2
4
1
1
12V DC-in jack (default) - SU171
15~36V DC-in jack (default) - SU173
DP++ port
HDMI/DP port (DP available upon request)
RJ45 LAN ports
USB 3.0 ports
Line-out jack
Mic-in jack
This jack is considered a low power solution. Connect a DC power cord to this jack. Using a
voltage more than the recommended range may fail to boot the system or cause damage to
the system board.
The DC-in jack on the system board co-lays with a 4-pin right angle connector (optional) or
4-pin vertical type connector (optional) as the photo displayed below.
4-pin Vertical Type (optional)
4-pin Right Angle
(optional)
DC-in (default)
17
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Graphics Interfaces
RJ45 LAN Ports
The display ports consist of the following:
•
•
1 DP++ port
1 HDMI/DP port
DP++
HDMI/DP
DP++
HDMI/DP
LAN 1
LAN 2
LAN 1
LAN 2
Features
DP Port
•
•
The DP port is a digital display interface used to connect a display device such as a computer
monitor. It is used to transmit audio and video simultaneously. The interface, which is developed by VESA, delivers higher performance features than any other digital interface.
Intel® I210AT PCIe (10/100/1000Mbps)
Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps) (only Core i7/i5 supports iAMT)
The LAN ports allow the system board to connect to a local area network by means of a network hub.
HDMI Port
BIOS Setting
The HDMI port which carries both digital audio and video signals is used to connect a LCD
monitor or digital TV that has the HDMI port.
Configure the onboard LAN ports in the Advanced menu (“ACPI Configuration” submenu) of
the BIOS. Refer to chapter 3 for more information.
BIOS Setting
Driver Installation
Configure the display devices in the Advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to chapter 3 for more information.
Install the LAN drivers. Refer to chapter 4 for more information.
Driver Installation
Install the graphics driver. Refer to chapter 4 for more information.
18
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
USB Ports
BIOS Setting
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to chapter 3 for more information.
Driver Installation
You may need to install the proper drivers in your operating system to use the USB device.
Refer to your operating system’s manual or documentation for more information.
Wake-On-USB Keyboard/Mouse
USB 3.0
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
USB 2
USB 1
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
USB 4
USB 3
USB 3.0
USB 9-10 USB 7-8
N. C.
GND
+Data
-Data
VCC
USB 2.0 2
1
10
9
GND
+Data
-Data
VCC
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with four onboard USB 3.0 ports (USB 1-2/3-4). The 10-pin
connectors allow you to connect 4 additional USB 2.0 ports (USB 7-8/9-10). The additional
USB ports may be mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear of the system chassis and then insert the USB port cables to a connector.
19
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Audio
I/O Connectors
Digital I/O Connector
Digital I/O Power Connector
1
Digital I/O
Line-out Mic-in
Line-out
Mic-in
Rear Audio
Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
•
Mic-in (Pink)
This jack is used to connect an external microphone.
1
The 8-bit Digital I/O connector provides powering-on function to external devices that are connected to the connector.
The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
•
4
+5V
5VSB
Ground
+12V
Digital I/O Power
Digital I/O Connector
Pins
Function
1
DIO7
BIOS Setting
2
DIO6
Configure the onboard audio devices in the Advanced menu (“Audio Configuration” submenu)
of the BIOS. Refer to chapter 3 for more information.
3
DIO5
4
DIO4
5
DIO3
6
DIO2
7
DIO1
8
DIO0
Driver Installation
Install the audio driver. Refer to the chapter 4 for more information.
20
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
SATA (Serial ATA) Power Connectors
SATA
Power 0
SATA
Power 2
1
4
1
7
GND
RXP
RXN
GND
TXN
TXP
GND
SATA 0
+12V
Ground
Ground
+5V
SATA (Serial ATA) Connectors
SATA 2
These SATA power connectors supply power to the SATA drive. Connect one end of the provided power cable to the SATA power connector and the other end to your storage device.
SATA 3.0 6Gb/s
Features
•
2 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
•
Supports RAID 0/1/5
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
BIOS Setting
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to chapter 3 for more information.
21
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM (Serial) Ports
RS232
COM 1
COM 4
COM 2 COM 3
DATANC.
NC.
NC.
9
RS485
Configure the serial COM ports in the Advanced menu (“SIO NUVOTON6106D” submenu) of
the BIOS. Refer to the chapter 3 for more information.
RXD
DTRDSRCTS9
RS422
Full Duplex
2
1
9
DCDTXD
GND
RTSRI-
2
1
9
BIOS Setting
COM 3/COM 4:
RS232
2
1
2
1
DATA+
NC.
GND
NC.
NC.
DCDTXD
GND
RTSRI-
9
RXD+
TXD+
GND
NC.
NC.
2
1
RXDTXDNC.
NC.
RXD
DTRDSRCTS-
COM 1/COM 2
COM 1/COM 2:
RS232/422/485
The pin functions of COM 1 and COM 2 will vary according to BIOS’ setting. JP4 (for COM 1)
and JP5 (for COM 2) are designed to configure Serial COM ports to pure RS232 or RS232 with
power. Refer to “COM 1/COM 2 RS232/Power Select” in this chapter for more information.
COM 3 and COM 4 are fixed at RS232.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
Connecting External Serial Ports
Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket to
an available slot at the rear of the system chassis then insert the serial port cable to the COM
connector. Make sure the colored stripe on the ribbon cable is aligned with pin 1 of the COM
connector.
22
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Front Panel Connector
Cooling Fan Connectors
Sense
Power
Ground
11
12
1
CPU Fan
HDD-LED
RESET-SW
Front
Panel
3
System Fan 2
1
3
1
2
Ground
Power
Sense
PWR-LED
PWR-BTN
System Fan 1
HDD-LED - HDD LED
1
3
This LED will light when the hard drive is being accessed.
Ground
Power
Sense
RESET-SW - Reset Switch
This switch allows you to reboot without having to power off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power
On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To
RAM) state, it will blink every 4 seconds.
The fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
PWR-BTN - Power Switch
BIOS Setting
This switch is used to power on or off the system.
Pin
HDD-LED
RESET-SW
Pin Assignment
Pin Pin Assignment
3
3V3
2
3V3SB
5
HDD_LED
PWR-LED 4
3V3SB
7
Ground
9
RST Signal
1, 11
N.C.
PWR-BTN
6
Power_LED
8
Ground
10
Power_Button
The Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS will display the current
speed of the cooling fans. Refer to chapter 3 for more information.
23
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LVDS LCD Panel Connector
LVDS LCD Panel Connector
LCD/Inverter Power Connector
Pins Function
40
2
39
1
LVDS LCD Panel
8
LCD/Inverter
Power
1
The system board allows you to connect a LCD Display Panel by means of the
LVDS LCD panel connector and the LCD/Inverter power connector. These connectors transmit video signals and power from the system board to the LCD
Display Panel.
Refer to the right side for the pin functions of these connectors.
Jumper Settings
Refer to the “Jumper Settings” section in this chapter for settings relevant to
the LCD panel.
BIOS Setting
Configure the LCD panel in the Advanced menu (“Video Configuration” submenu) of the BIOS. Refer to chapter 3 for more information.
LCD/Inverter Power Connector
Pins Function
Pins
Function
1
GND
2
GND
1
GND
3
LVDS_Out3+ (Odd_3+)
4
LVDS_Out7+ (Even_3+)
2
GND
5
LVDS_Out3- (Odd_3-)
6
LVDS_Out7- (Even_3-)
3
Panel Inverter Brightness Voltage Control
7
GND
8
GND
4
Panel Power
9
LVDS_Out2+ (Odd_2+)
10
LVDS_Out6+ (Even_2+)
5
+3.3V
11
LVDS_Out2- (Odd_2-)
12
LVDS_Out6- (Even_2-)
6
Panel Backlight On/Off Control
13
GND
14
GND
7
+12V (default) /+5V
15
LVDS_Out1+ (Odd_1+)
16
LVDS_Out5+ (Even_1+)
8
+12V (default) /+5V
17
LVDS_Out1- (Odd_1-)
18
LVDS_Out5- (Even_1-)
19
GND
20
GND
21
LVDS_Out0+(Odd_0+)
22
LVDS_Out4+ (Even_0+)
23
LVDS_Out0- (Odd_0-)
24
LVDS_Out4- (Even_0-)
25
GND
26
GND
27
LVDS_CLK1+ (Odd_CLK+)
28
LVDS_CLK2+ (Even_CLK+)
29
LVDS_CLK1- (Odd_CLK-)
30
LVDS_CLK2- (Even_CLK-)
31
GND
32
GND
33
LVDS_DDCCLK
34
N.C.
35
LVDS_DDCDATA
36
+3.3V
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
Note:
1. LVDS LCD Panel Connector:
DFI PN: 346-714000-201S
Description: HEADER 40P/1.25mm, 180D, SMD, BEIGE, DF13E-40DP-1.25V(51)(Hirose)RoHS
2. LCD/Inverter Power Connector:
DFI PN: 3346-510801-100G
Description: BOX HEADER 1*8, 8P/2.0mm/180D, 721-81-08TW00(PINREX)RoHS
24
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
SMBus
1
GND
SMBUS_Data
SMBus Connector
2
1
+3.3V_standby
SMBUS_CLK
SMBUS_Alert#
S/PDIF Connector
6
5
+5V
SPDIF out
Ground
SPDIF in
S/PDIF
5
The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis then connect the audio cable to the S/PDIF connector. Make sure pin 1
of the audio cable is aligned with pin 1 of the S/PDIF connector.
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
25
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Expansion Slots
Chassis Intrusion Connector
Chassis
Intrusion
PCI Express x4
Mini PCI Express
(PCIe, USB and mSATA signals)
Mini PCI Express
(PCIe and USB signals)
SIM Slot (optional)
2
1
Ground
Signal
The board supports the chassis intrusion detection function. Connect the chassis intrusion
sensor cable from the chassis to this connector. When the system’s power is on and a chassis
intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion
occurred, the alarm will sound only when the system restarts.
Mini PCI Express Slots
The Mini PCIe socket is used to install a Mini PCIe card. Mini PCIe card is a small form factor
PCIe card with the same signal protocol, electrical definitions, and configuration definitions as
the conventional PCIe.
BIOS Setting
PCI Express x4 Slot
Configure the chassis intrusion detection function in the Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS. Refer to the chapter 3 for more information.
Install PCI Express cards such as network cards or other cards that comply to the PCI Express
specifications into the PCI Express x4 slot.
SIM Slot (optional)
The SIM slot on the system board is used to insert a SIM card.
26
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
eDP Connector (Optional)
Pins
eDP
1
29
2
30
The eDP connector is an embedded displayport which has advanced power-saving features
to connect a display device to transmit digital communication of audio and video signals. The
table below indicates the pin fuctions of the eDP connector.
Jumper Settings
Refer to the “Jumper Settings” section in this chapter for settings relevant to the eDP panel.
Pin Assignment
Pins
Pin Assignment
1
GND
2
GND
3
eDP_Lane 0-
4
eDP_Lane 3-
5
eDP_Lane 0+
6
eDP_Lane 3+
7
GND
8
NC
9
eDP_Lane 1-
10
GND
11
eDP_Lane 1+
12
AUX-
13
GND
14
AUX+
15
eDP_Lane 2-
16
GND
17
eDP_Lane 2+
18
Hot Plug
19
+V_LCD
20
+V_LCD
21
GND
22
GND
23
Panel Backlight On/Off
Control
24
Panel Inverter Brightness
Voltage Control
25
Inverter GND
26
Inverter GND
27
3V3
28
Inverter PWR
29
Inverter PWR
30
Inverter PWR
27
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LPC Connector
Connecting the EXT-RS232/RS485 Card to the Motherboard
With DFI’s proprietary technology, SU171/SU173 supports two extension modules for additional
four COM ports. The EXT-RS232/RS485 card is connected to SU171/SU173 via the LPC connector. The illustrations below guide you how to connect the extension module to the motherboard.
LPC Connector
13
1
14
2
Note:
The motherboard used in the following illustrations does not resemble the actual one.
These illustrations are for reference only.
Top View
LPC
COM
Bottom View
LPC
EXT-RS485
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition
towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components
within the system, which are typically provided by a Super I/O controller. Furthermore, it can be
used to interface firmware hubs, Trusted Platform Module (TPM) devices(*) and embedded controller solutions. Data transfer on the LPC bus is implemented over a 4 bit serialized data interface,
which uses a 24MHz LPC bus clock. For more information about LPC bus refer to the Intel® Low
Pin Count Interface Specification Revision 1.1’. The table below indicates the pin fuctions of the
LPC connector.
Pins
1
3
5
7
9
11
13
Pin Assignment
CLK_24M
RST#
FRAME#
LAD3
LAD2
SERIRQ
5VSB
Pins
2
4
6
8
10
12
14
Pin Assignment
LAD1
LAD0
VCC3
GND
GND
5V
EXT-RS485
DFI Carrier Board
EXT-RS232/RS485
Additional 4 COM
Note:
*SU171/SU173 support the TPM module and onboard TPM IC (Infineon SLB
9665TT2.0 dTPM IC).
28
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Standby Power LED
Battery
1
2
+3.3V
GND
Battery
Connector
Standby Power LED
This LED will lit red when the system is in the standby mode. It indicates that there is power
on the system board. Power-off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
Battery
Connect to the
battery connector
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to local ordinance.
29
Chapter 2 Hardware Installation
www.dfi.com
Chapter 3
Chapter 3 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
<F5>
Scrolls forward through the values or options of the highlighted field.
<F6>
Scrolls backward through the values or options of the highlighted field.
<F1>
Displays general help
<F9>
Optimized defaults
<F10>
Saves and resets the setup program.
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
Entering the BIOS Setup Utility
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When “” appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
30
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Project Name
BIOS Version
SU17x
61.13A
Processor Type
CPUID:
CPU Speed:
CPU Stepping:
L1 Data Cache:
L1 Instruction Cache:
L2 Cache:
L3 Cache:
Number of Processors:
Microcode Rev:
Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz
0x406E3 (SKYLAKE ULT ULX)
2500 MHz
03 (D0/K0 Stepping)
32 KB
32 KB
256 KB
3072 KB
2 Core(s) / 4 Thread(s)
00000057
Total Memory
System Memory Speed
SODIMM 0
SODIMM 1
4096 MB
1600 MHz
[Not Installed]
4096 MB
PCH Rev / SKU
Intel ME Version / SKU
21 (C1 Stepping) / SKL PCH-LP (U) Premium
SKU
11.0.0. 1180 / CORPORATE
System Time
System Date
[13:13:03]
[01/27/2016]
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
Important:
Setting incorrect field values may cause the system to malfunction.
Rev. 5.0
This is the help for the
hour, minute, second
field. Valid range is from
0 to 23, 0 to 59, 0 to 59.
INCREASE/REDUCE:
+/-.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
ACPI Configuration Setting
ACPI
Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
F5/F6 Change Values
Enter Select  SubMenu
MEBX Configuration
Active Management Technology Supoort
SIO NUVOTON6106D
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from 01 to
12. Date displays the date, from 01 to 31. Year displays the year, from 2000 to 2099.
31
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
ACPI Configuration
CPU Configuration
This section is used to configure the system ACPI parameters.
This section is used to configure the CPU.
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
Determines the action taken when the system power
is off and a PCI Power
Management Enable wake
up event occurs.
ACPI Configuration
Wake on LAN
State After G3
F1 Help
Esc Exit
Rev. 5.0
Advanced
<Enabled>
<S0 State>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
CPU Configuration
Intel(R) SpeedStep(tm)
Turbo Mode
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
<Enabled>
<Enabled>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Allows more than two frequency ranges to be supported.
F9 Setup Defaults
F10 Save and Exit
Wake on LAN
Intel(R) SpeedStep(tm)
This field use to enable or disable the LAN signal to wake up the system.
This field is used to enable or disable the Intel Enhanced SpeedStep Technology.
State After G3
Turbo Mode
This field is to specify what state to go when power is re-applied after a power
failure (G3 state).
Enable or disable the turbo mode.
S0 State
The system working state.
S5 State
Off, except for trickle current to devices such as the power button.
32
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Video Configuration
InsydeH20 Setup Utility
This section configures the video settings.
InsydeH20 Setup Utility
Rev. 5.0
Video Configuration
<Auto>
<Auto>
<Disabled>
<DP+HDMI>
<Normal>
<18 Bit>
<PWM Mode>
<1024x768>
Primary Display
Internal Graphics
Always Enabled PEG
Boot display
Backlight Control
Panel Color Depth
LVDS Mode
LCD Panel Type
Select which of IGFX/
PEG/PCI Graphics device
should be Primary Display
or Select SG fro Switchable Gfx.
Boot display
Primary Display
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Boot display
Primary Display
Set the display device combination.
Set the initial priority.
Backlight Control
InsydeH20 Setup Utility
Rev. 5.0
Select the Normal/Inverted.
Advanced
Keep IGFX enabled based
on the setup options.
Video Configuration
Primary Display
Internal Graphics
Always Enabled PEG
Boot display
Backlight Control
Panel Color Depth
LVDS Mode
LCD Panel Type
<Auto>
<Auto>
<Disabled>
<DP+HDMI>
<Normal>
<18 Bit>
<PWM Mode>
<1024x768>
LCD+DP
LCD+HDMI
HDMI+LCD
HDMI+DP
DP+LCD
DP+HDMI
Auto
IGFX
PEG
PCI
F1 Help
Esc Exit
Chose display device combination
Video Configuration
Advanced
Primary Display
Internal Graphics
Always Enabled PEG
Boot display
Backlight Control
Panel Color Depth
LVDS Mode
LCD Panel Type
Rev. 5.0
Advanced
Panel Color Depth
<Auto>
<Auto>
<Disabled>
<DP+HDMI>
<Normal>
<18 Bit>
<PWM Mode>
<1024x768>
Select the LFP panel color depth: 18 bit, 24 bit, 36 bit or 48 bit.
LVDS Mode
Select the PWM/DC Mode
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Note:
In order to control "Primary Display" & "Boot Display", you need to go to Boot tab
and select different "Boot Type" (Boot Section, Page 42)
Boot Type : Legacy Boot Type -> Hide Primary Display & Show Boot Display
Boot Type : UEFI Boot Type -> Show Primary Display & Hide Boot Display
Boot Type : Dual Boot Type -> Show Primary Display & Show Boot Display
F9 Setup Defaults
F10 Save and Exit
Internal Graphics
Keep IGFX enabled or disabled based on the setup options.
Always Enabled PEG
Enable or disable the PEG function.
33
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Audio Configuration
This section is used to configure the audio settings.
InsydeH20 Setup Utility
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Advanced
Primary Display
Internal Graphics
Always Enabled PEG
Boot display
Backlight Control
Panel Color Depth
LVDS Mode
LCD Panel Type
HD Audio
Select LCD Panel Type
Video Configuration
Control Detection of the
HD-Audio device.
<Enabled>
<Auto>
<Auto>
<Disabled>
<DP+HDMI>
<Normal>
<18 Bit>
<PWM Mode>
<1024x768>
Disabled = HDA will be
unconditionally disabled
Enabled = HDA will be
unconditionally enabled
Auto = HDA will be enabled if present, disabled
otherwise.
LCD Panel Type
800x480
800x600
1024x768
1366x768
1280x1024
1920x1080
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
LCD Panel Type
HD Audio
Select the LCD panel type.
Control the detection of the HD-Audio device.
F9 Setup Defaults
F10 Save and Exit
Disabled
HDA will be unconditionally disabled.
Enabled
HDA will be unconditionally enabled.
Auto
HDA will be enabled if present, disabled otherwise.
34
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
SATA Configuration
USB Configuration
This section is designed to select the SATA controller and the type of hard disk drive which are
installed in your system unit.
This section is used to configure the parameters of the USB device.
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
SATA Controller(s)
SATA Mode Selection
Serial ATA Port 0
Port 0
Serial ATA Port 1
Port 1
Serial ATA Port 2
Port 2
F1 Help
Esc Exit
Rev. 5.0
Advanced
<Enabled>
<AHCI>
[ST4000NM0033-9ZM170 ]
<Enabled>
[Not Installed]
<Enabled>
[Not Installed]
<Enabled>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Enable/Disable SATA
Device.
USB BIOS Support
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
SATA Controller(s)
USB BIOS Support
This field is used to enable or disable Serial ATA devices.
Disabled
USB keyboard/mouse/storage support under UEFI
and DOS environment. It
will supporting UEFI environment only if set to
UEFI Only
<Enabled>
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Disable USB keyboard/mouse/storage support under UEFI and DOS environment.
SATA Mode Selection
Enabled
The mode selection determines how the SATA controller(s) operates.
Enable USB keyboard/mouse/storage support under UEFI and DOS environment.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
RAID Mode
This option allows you to create RAID or Intel Matrix Storage configuration on Serial
ATA devices.
UEFI Only
Enable USB keyboard/mouse/storage support under UEFI environment.
Serial ATA Port 0,1 and 2
This field is used to enable or disable the serial ATA port.
35
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
PCI Express Configuration
This section configures settings relevant to PCI Express root ports.
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
PCI
PCI
Express
Express
PCI Express
PCI Express
PCI Express
F1 Help
Esc Exit
Root
Root
Root
Root
Root
Port
Port
Port
Port
Port
Rev. 5.0
Advanced
PCI Express Root Port 1
Settings.
1
6
7
8
9
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
InsydeH20 Setup Utility
PCI Express Root Port 6
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
<Enabled>
<AUTO>
F5/F6 Change Values
Enter Select  SubMenu
Control the PCI Express
Root Port.
F9 Setup Defaults
F10 Save and Exit
PCI Express Root Port
Rev. 5.0
Advanced
PCI Express Root Port 1
PCIe Speed
↑/↓ Select Item
←/→ Select Item
<Enabled>
This field is used to enable or disable the PCI Express Root Port.
Control the PCI Express
Root Port.
PCIe Speed
Select the speed of the PCI Express Root Port: Auto, Gen1, Gen2 or Gen3.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
36
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
ME Configuration
Active Management Technology Support
This section configures settings relevant to flash ME region.
The section allows users to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Refer to chapter 6 for more information.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Me Fw Image Re-Flash
InsydeH20 Setup Utility
<Disabled>
Enable/disable to flash ME
region
Active Management Technology Support
Intel AMT Support
Un-Configure ME
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Rev. 5.0
Advanced
Enable/Disable Intel(R)
Active Management Technology BIOS Extension.
Note : iAMT H/W is always enabled. This Option
Just controls the BIOS
extension execution.
<Disabled>
<Disabled>
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
Me Fw Image Re-Flash
This field is used to enable or disable the flash ME region.
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
MEBX Configuration
This section configures MEBX setting. Please refer to Chapter 6 for more information.
37
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
SIO NUVOTON6106D
InsydeH20 Setup Utility
This section configures the system super I/O chip parameters.
InsydeH20 Setup Utility
SYS Smart Fan Control
Fix Fan Speed Count
CPU Smart Fan Control
Fix Fan Speed Count
SYS Smart Fan 2 Control
Fix Fan Speed Count
COM Port 1
Base I/O Address
Interrupt
Type
COM Port 2
Base I/O Address
Interrupt
Type
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
WDT
Case Open
AC Power Loss
PC Health Status
Rev. 5.0
Advanced
SYS Smart Fan Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
CPU Smart Fan Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
SYS Smart Fan 2 Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
Rev. 5.0
Advanced
Enable/Disable Smart Fan
F1 Help
Esc Exit
F5/F6 Change Values
Enter Select  SubMenu
Enable/Disable Smart Fan
F9 Setup Defaults
F10 Save and Exit
Note:
SYS Smart Fan, Fan2 and CPU Smart Fan Control can be switched to <Disable>.
When they are disabled, it will enable "Fix Fan Speed Count".
↓
F5/F6 Change Values
Enter Select  SubMenu
↑/↓ Select Item
←/→ Select Item
<Disable>
[50]
<Disable>
[50]
<Disable>
[50]
<Enable>
<3F8>
<IRQ4>
<RS232>
<Enable>
<2F8>
<IRQ3>
<RS232>
<Enable>
<3E8>
<IRQ4>
<Enable>
<2E8>
<IRQ3>
<Disable>
<Disable>
<Always off>
F9 Setup Defaults
F10 Save and Exit
SYS/CPU Smart Fan/Fan 2 Control
Enable or disable the system/CPU smart fan/fan 2.
Boundary 1 to Boundary 4
Set the boundary temperature. The range is from 0-127oC.
Fan Speed Count 1 to Fan Speed Count 4
Set the fan speed. The range is from 1-100%.
38
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
InsydeH20 Setup Utility
Advanced
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
COM Port 1
Base I/O Address
Interrupt
Type
COM Port 2
Base I/O Address
Interrupt
Type
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
WDT
Case Open
AC Power Loss
PC Health Status
F1 Help
Esc Exit
Rev. 5.0
InsydeH20 Setup Utility
Advanced
↑
[30]
[40]
[50]
[75]
<Enable>
<3F8>
<IRQ4>
<RS232>
<Enable>
<2F8>
<IRQ3>
<RS232>
<Enable>
<3E8>
<IRQ4>
<Enable>
<2E8>
<IRQ3>
<Disable>
<Disable>
<Always off>
↑/↓ Select Item
←/→ Select Item
Configure Serial port using
options: [Disable] No Configuration [Enable] User
Configuration
F5/F6 Change Values
Enter Select  SubMenu
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
COM Port 1
Base I/O Address
Interrupt
Type
COM Port 2
Base I/O Address
Interrupt
Type
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
WDT
WDT
Counter
Case Open
AC Power Loss
PC Health Status
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
Rev. 5.0
↑
[30]
[40]
[50]
[75]
<Enable>
<3F8>
<IRQ4>
<RS232>
<Enable>
<2F8>
<IRQ3>
<RS232>
<Enable>
<3E8>
<IRQ4>
<Enable>
<2E8>
<IRQ3>
<Enabled>
<SECOND>
[38]
<Disable>
<Always off>
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
WDT
COM Port 1 to COM Port 4
Configure the settings to use the serial port.
Enable or disable the watchdog function. A counter will appear if you select to enable
WDT. Input any value between 1 to 255.
Disable No configuration
Case Open
Enable
User configuration
Enable or disable the case open detection function.
Type
AC Power Loss
Choose RS232/RS485/RS422 (Peer-to-Peer) for the serial port type for COM port 1 and
COM port 2.
Set the AC power loss always off/on.
39
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Security
PC Health Status
This section only displays the PC health status.
InsydeH20 Setup Utility
Rev. 5.0
Main
Advanced
Voltage
VCORE
5V
+12V
VDDQ
VBAT
3VSB
0.848 V
5.056 V
11.880 V
1.376 V
3.072 V
3.328 V
Temperature
System (oC/oF)
CPU (oC/oF)
28.0 C/ 82.4 F
66.5 C/ 151.7 F
Fan Speed
SYS FAN
CPU FAN
SYS FAN2
0 RPM
2054 RPM
0 RPM
↑/↓ Select Item
←/→ Select Item
Security
Current TPM Device
TPM State
TPM Availability
TPM Operation
Clear TPM
Supervisor Password
PC Health Status
F1 Help
Esc Exit
Advanced
InsydeH20 Setup Utility
Boot
Exit
<TPM 2.0 (DTPM)>
Enabled, Owned
<Available>
<No Operation>
[]
Not installed
Rev. 5.0
When Hidden, don’t exposes TPM to 0
Set Supervisor Password
Set All Hdd Password
Set All Master Hdd Password
TMP Availability
F5/F6 Change Values
Enter Select  SubMenu
Storage
Password Setup Page
Available
Hidden
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
TPM Availability
Set the TPM availability.
TPM Operation
Enable or disable the storage and endorsement hierarchy. This option will
automatically return to No-Operation.
Clear TPM
Remove all TPM context associated with a specific owner.
Set Supervisor Password
Set the supervisor’s password and the length of the password must be greater than
one character.
Set All Hdd Password
Set all HDD password and suggest the length of password greater than one character.
This item can be displayed when any security mode of HDD is not Lock.
Set All Master Hdd Password
Set all master HDD password and suggest the length of password greater than one
character. This item can be displayed when any security mode of HDD is not Lock.
40
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Storage Password Setup Page
Main
Main
Advanced
Security
Current TPM Device
TPM State
TPM Availability
TPM Operation
Clear TPM
Supervisor Password
InsydeH20 Setup Utility
Boot
Exit
<TPM 2.0 (DTPM)>
Enabled, Owned
<Available>
<No Operation>
[]
Not installed
Rev. 5.0
Storage Password Setup
Page
Advanced
InsydeH20 Setup Utility
Boot
Exit
Security
Device Name:
[ST3160318AS]
Security Mode:
No Accessed
Rev. 5.0
Set Storage Password
Set Master Hdd Password
Set Supervisor Password
Set All Hdd Password
Set All Master Hdd Password
Storage
Password Setup Page
F1 Help
Esc Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Security Mode Description
Lock: HDD security status is enable and lock.
Unlock: HDD security status is enable and lock.
Storage Password Setup Page
This option allowes you to set up storage password.
Change: HDD security status is unlock and user changes to the new password.
Disable: Remove HDD password from device.
No Access: HDD Secutiry status is not enabled when entering SCU.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
Set Storage Password
Storage Password Setup
Page
Storage Password Setup
Set all HDD password and suggest the length of password greater than one character.
How to clear HDD password: only press “Enter” when set new password.
ST3160318AS
↑ and ↓ to change option. ENTER to select an option. ESC to exit.
Set Master Hdd Password
Set master HDD password and suggest the length of password greater than
one character.
When secutiry mode is Lock, input master HDD password to unlock HDD.
Master HDD password is valid when HDD password is set.
Only pressing “Enter” would clear HDD password and make HDD secutiry disable
when set new master HDD password.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
ST3160318AS (Device Name)
This option allowes you to go to Storage Password List Help.
41
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Boot
USB Boot
Enable or disable the booting to USB boot devices.
Main
Advanced
Security
Numlock
Boot Type
Network Stack
PXE Boot Capability
USB Boot
InsydeH20 Setup Utility
Boot
Exit
<On>
<Dual Boot Type>
<Disabled>
<Disabled>
<Enabled>
Rev. 5.0
Selects Power-on state for
Numlock
Main
EFI
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Legacy
Rev. 5.0
EFI Boot Order Settings
Numlock
Boot Type
Network Stack
PXE Boot Capability
USB Boot
<On>
<Dual Boot Type>
<Disabled>
<Disabled>
<Enabled>
EFI
Legacy
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Numlock
Select the power-on state for numlock.
F1 Help
Esc Exit
Boot Type
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
EFI
Select the boot type. The options are Dual Boot Type, Legacy Boot Type or UEFI Boot
Type.
This section is used to set EFI boot order.
If you select “Dual Boot” or “UEFI Boot”, the “Network Stack”, PXE Boot capability”
and “USB Boot” will show up.
If you select “Legacy Boot”, “PXE Boot to LAN” and “USB Boot” will show up.
Network Stack
This field is used to enable or disable network stack.
PXE Boot capability
Disabled : Suppoort Network Stack
UEFI PXE : IPv4/IPv6
Legacy : Legacy PXE OPROM only
PXE Boot to LAN
Disable or enable PXE boot to LAN.
42
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Legacy
Boot Type Order
This section is used to set legacy boot order.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Select Normal Boot Option
Priority or Advance Boot
Option Priority
Boot Device Priority
Normal Boot Menu
Boot
Use + and - keys to arrange the sequence of storage devices that the system’s
hardware checks for the operating system’s boot files. The first device in the order list
has the first boot priority. For example, to boot from a floppy drive instead of a hard
drive, place the floppy drive ahead of the hard drive in priority.
Rev. 5.0
<Normal>
Main
Type Order
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
Boot Type Order
Boot Type Order
CD/DVD-ROM Drive
USB
Others
Hard Disk Drive
Floppy Drive
Normal Boot Menu
Normal
Advance
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Normal Boot Menu
F1 Help
Esc Exit
Normal
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Based on the boot normal priority, it determines the EFI device first or the legacy
device first.
Advance
All boot devices follow the user’s selection sequence. Use + and - keys to arrange
the priority of the listed boot devices.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Boot Device Priority
Normal Boot Menu
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Advance>
F5/F6 Change Values
Enter Select  SubMenu
Rev. 5.0
Select Normal Boot Option
Priority or Advance Boot
Option Priority
F9 Setup Defaults
F10 Save and Exit
43
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Exit
Updating the BIOS
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions about how to
update BIOS with the flash utility.
Rev. 5.0
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing BIOS updating procedure. For your convenience, we
will also provide you with an auto-execution file in the BIOS file downloaded. This RS@32
-execution file will bring you directly to the flash utility menu soon after system boots up and
finishes running the boot files in your boot disk.
Exit system setup and save
your changes.
Exit Saving Changes
Load Optimal Defaults
Discard Changes
RRead file successfully.
(path= “platform.ini”)
Information
Please do not remove the AC power
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Initializing
Current BIOS Model name: SU171/173
New BIOS Model name: SU171/173
Current BIOS version: 65.05A
New BIOS version: 65.05A
Exit Saving Changes
0%
Select this field and then press <Enter> to exit the system setup and save your
changes.
Updating Block at FFFFF000h
25%
50%
75%
100%
100%
C:\SU171/173>_
Load Optimal Defaults
Select this field and then press <Enter> to load optimal defaults.
Discard Changes
Select this field and then press <Enter>to exit the system setup without saving your
changes.
44
Chapter 3 BIOS Setup
www.dfi.com
Chapter 3
Notice: BIOS SPI ROM
1. The Intel® Management Engine has already been integrated into this system board. Due to
the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board
and used on another system board of the same model.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
45
Chapter 3 BIOS Setup
www.dfi.com
Chapter 4
Chapter 4 - Supported Software
For Windows 8.1
Install drivers, utilities and software applications that are required to facilitate and enhance the
performance of the system board. You may acquire the software from your sales representatives, from an optional DVD included in the shipment, or from the website download page at
https://www.dfi.com/DownloadCenter.
For Windows 10
46
Chapter 4 Supported Software
www.dfi.com
Chapter 4
For Windows 7
Intel Chipset Software Installation Utility
The Intel Chipset Software Installation Utility is used for updating Windows® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Software Installation Utility” on the main menu.
1. Setup is ready to install the
utility. Click Next.
2. Read the license agreement
then click Yes.
Note:
This step can be ignored if the applications are standalone files.
47
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Graphics Drivers
3. Go through the readme
document for more installation tips then click Next.
To install the driver, click “Intel Graphics Drivers” on the main menu.
1. Setup is now ready to
install the graphics driver.
Click Next.
4. Click Finish to exit setup.
By default, the “Automatically run WinSAT and enable the Windows Aero
desktop theme” is enabled. With this enabled, after installing the graphics
driver and the system rebooted, the screen will turn blank for 1 to 2 minutes
(while WinSAT is running) before the Windows Vista desktop appears. The
“blank screen” period is the time Windows is testing the graphics performance.
2. Read the license agreement
then click Yes.
48
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Audio Drivers
3. Go through the readme
document for system requirements and installation
tips then click Next.
To install the driver, click “Audio Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
4. Setup is now installing the
driver. Click Next to continue.
2. Click “Yes, I want to restart
my computer now” then
click Finish.
Restarting the system will
allow the new software
installation to take effect.
5. Click “Yes, I want to restart
this computer now” then
click Finish.
Restarting the system will
allow the new software
installation to take effect.
49
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel LAN Drivers
4. Click Install to begin the
installation.
To install the driver, click “Intel LAN Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
5. After completing installation, click Finish.
2. Click “I accept the terms
in the license agreement”
then click “Next”.
3. Select the program featuers
you want installed then
click Next.
50
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Kernel Mode Driver (For Windows 7 only)
3. Click “Restart Now“ to
restart your computer when
the installation is complete.
To install the driver, click “Kernel Mode Driver Framework” on the main menu.
1. Click “Yes“ to install the
update.
2. The update is installed
now.
51
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Management Engine Drivers
3. Setup is currently installing
the driver. After installation
has completed, click Next.
To install the driver, click “Intel Management Engine Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
4. Please wait while the product is being installed.
2. Read the license agreement
then click Next.
5. After completing installation, click Finish.
52
Chapter 4 Supported Software
www.dfi.com
Chapter 4
HW Utility
3. Click “Install” to begin the
installation.
HW Utility provides information about the board, Watchdog,and DIO. To access the utility, click
“HW Utility” on the main menu.
Note:
If you are using Windows 7 or later versions, it needs administrator privilege to be
able to install/execute the utility.
1. Setup is ready to instal
the HW Utility driver
Click “Next”.
4. After completing installa
tion, click “Finish”.
2. Click “I accept the terms in
the license agreement” then
click “Next”.
53
Chapter 4 Supported Software
www.dfi.com
Chapter 4
The HW Utility icon will appear on the desktop. Double-click the icon to open the utility.
Information
HW Health Set
WatchDog
HW Health
54
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel USB 3.0 Drivers (For Windows 7 and Windows 8.1)
To install the driver, click “Intel USB 3.0 Driver” on the main menu.
1. Setup is ready to install the driver.
Click Next.
DIO
2. Read the license agreement then
click Yes.
55
Chapter 4 Supported Software
www.dfi.com
Chapter 4
IO Driver (Windows 7, Windows 8.1 and Windows 10)
3. Go through the readme document for more installation tips
then click Next.
To install the driver, click “Intel Serial IO Driver” on the main menu
1. Setup is ready to install the driver.
Click Next.
4. Setup is currently installing the
driver. After installation has completed, click Next.
2. Read the license agreement carefully.
Click “I accept the terms in the License Agreement” then click Next.
5. After completing installation, click
Finish.
56
Chapter 4 Supported Software
www.dfi.com
Chapter 4
3. Read the file information then click
Next.
5. Setup is now installing the
driver.
4. Setup is ready to install the driver.
Click Next.
6. Click Finish.
57
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Microsoft Framework 4.5.2 (For Windows 7)
3. Setup is now installing the
driver.
Note:
Before installing Microsoft Framework 4.5.2, make sure you have updated your
Windows 7 operating system to Service Pack 3.
To install the driver, click “Microsoft Framework 4.5.2” on the main menu.
1. Setup is now extracting files.
4. Click Finish.
2. Read the license agreement carefully.
Click “I have read and accept
the terms of the License Agree
ment” then click Install.
58
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Intel Rapid Storage Technology
Infineon TPM 1.2 Driver and Tool (optional)
To install the driver, click “Infineon TPM driver and tool (option)” on the main menu.
The Intel Rapid Storage Technology is a utility that allows you to monitor the current status
of the SATA drives. It enables enhanced performance and power management for the storage
subsystem.
1. The setup program is preparing
to install the driver.
To install the driver, click “Intel Rapid Storage Technology” on the main menu. Please refer to
Chapter 5 for more information.
2. The setup program is now ready
to install the utility. Click Next.
3. Click “I accept the terms in the
license agreement” and then
click “Next”.
59
Chapter 4 Supported Software
www.dfi.com
Chapter 4
4. Enter the necessary information
and then click Next.
7. TPM requires installing the Microsoft Visual C++ package prior to
installing the utility. Click Install.
5. Select a setup type and then click
Next.
8. The setup program is currently
installing the Microsoft Visual
C++ package.
9. Click Finish.
6. Click Install.
60
Chapter 4 Supported Software
www.dfi.com
Chapter 4
Adobe Acrobat Reader 9.3
10. Click “Yes“ to restart your system.
To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.
1. Click Next to install or click
Change Destination Folder
to select another folder.
2. Click Install to begin installation.
3. Click Finish to exit installation.
61
Chapter 4 Supported Software
www.dfi.com
Chapter 5
Chapter 5 - RAID
Settings
The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1,
and RAID 5.
To enable the RAID function, the following settings are required.
1. Connect the Serial ATA drives.
RAID Levels
2. Enable RAID in the Insyde BIOS.
RAID 0 (Striped Disk Array without Fault Tolerance)
3. Create a RAID volume.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk
drives. This improves the I/O performance of the drives at different channel; however it is not
fault tolerant. A failed disk will result in data loss in the disk array.
4. Install the Intel Rapid Storage Technology Utility.
Step 1: Connect the Serial ATA Drives
RAID 1 (Mirroring Disk Array with Fault Tolerance)
Refer to chapter 2 for details on connecting the Serial ATA drives.
RAID 1 copies and maintains an identical image of the data from one drive to the other drive.
If a drive fails to function, the disk array management software directs all applications to the
other drive since it contains a complete copy of the drive’s data. This enhances data protection
and increases fault tolerance to the entire system. Use two new drives or an existing drive and
a new drive but the size of the new drive must be the same or larger than the existing drive.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID BIOS utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
RAID 5
RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides
better hard drive performance and more storage capacity.
Step 2: Enable RAID in the Insyde BIOS
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
2. Go to “Advanced” menu, and select the “SATA Configuration” menu.
3. Change the “SATA Mode Selection” to “RAID” mode.
4. Save the changes in the “Save & Exit” menu.
5. Reboot the system.
62
Chapter 5 RAID
www.dfi.com
Chapter 5
Step 3: Create a RAID Volume
Step 4: Install the Intel Rapid Storage Technology Utility
1. When the Intel RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/
or SATA drives. It enables enhanced performance and power management for the storage
subsystem.
4. Use the up or down arrow keys to select the strip size and press <Enter>.
1. Insert the provided DVD into an optical drive.
5. Press <Enter> to select the physical disks.
2. Click “Intel Rapid Storage Technology Utility” on the main menu.
®
2. Select 1: Create RAID Volume and press <Enter>.
6. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
3. Setup is ready to install
the utility. Click Next.
7. Press <Enter>.
8. Select the volume size and press <Enter>. You must select less than one hundred percent
of the available volume space to leave space for the second volume.
9. Press <Enter> to create the volume.
10. At the prompt, press <Y> to confirm volume creation.
11. Select 4: Exit and press <Enter>.
12. Press <Y> to confirm exit.
Note:
These steps are cited from the Intel® Suppot site, “Set Up a System with Intel®
Matrix RAID Technology” (Article ID: 000005789).
http://www.intel.com/content/www/us/en/support/boards-and-kits/000005789.htm
4. Read the license agreement and click “I accept
the terms in the License
Agreement.“ Then, click
Next.
63
Chapter 5 RAID
www.dfi.com
Chapter 5
5. Go through the readme
document to view system
requirements and installation information then click
Next.
8. Click “Yes, I want to restart
this computer now” to
complete the installation
and then click Finish.
6. Click Next to install to
the default folder or click
change to choose another
destination folder.
7. Confirm the installation and
click Next.
64
Chapter 5 RAID
www.dfi.com
Chapter 6
Chapter 6 - Intel AMT Settings
Enable Intel® AMT in the Insyde BIOS
Overview
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
Intel Active Management Technology (Intel® AMT) combines hardware and software solution to
provide maximum system defense and protection to networked systems.
2. In the Advanced menu, select Active Management Technology Support.
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
•
Main
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
MEBX Configuration
Active Management Technology Supoort
SIO NUVOTON6106D
Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
•
Security
AMT Configuration
Discover
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
•
Advanced
Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
3. In the Intel AMT Support field, select Enabled.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Active Management Technology Support
Intel AMT Support
Un-Configure ME
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enabled>
<Disabled>
F5/F6 Change Values
Enter Select  SubMenu
Enable/Disable Intel(R)
Active Management Technology BIOS Extension.
Note : iAMT H/W is always enabled. This Option
Just controls the BIOS extension execution.
F9 Setup Defaults
F10 Save and Exit
65
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
Configure Intel® AMT in the Intel® Management Engine BIOS
4. In the Exit menu, select Exit Saving Changes then select Yes and press Enter.
Extension (MEBX) Section
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
1. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password
then press Enter.
Exit system setup and save
your changes.
Exit Saving Changes
Load Optimal Defaults
Discard Changes
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Intel(R) ME Password
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
66
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
2. Enter a password in the space provided under Intel(R) ME Password then press Enter. The
password must include:
•
•
•
•
•
3. You will be asked to verify the password. Enter the same new password in the space provided under Verify Password then press Enter.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
Intel(R) ME Password
4. Select Intel(R) ME General Settings then press Enter.
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
67
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
5. Select Change Intel(R) ME Password then press Enter.
6.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under Intel(R) ME New Password then press Enter.
•
•
•
•
•
Select Local FW Update then press Enter. Select Enabled or Disabled or password
Protected then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
Disabled
Enabled
Password Protected
<Enabled>
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
7.
Intel (R) ME New Password
[] = Move Highlight
[Enter] = Select Entry
Select Previous Menu until you return to the Main Menu. Select Intel(R) AMT Configuration then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
[Esc]= Exit
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[] = Move Highlight
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
68
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
8.
In the Intel(R) AMT Configuration menu, select Manageability Feature Selection
then press Enter. Select Enabled or Disabled then press Enter.
10.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved..
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
In the Intel(R) AMT Configuration menu, select SOL/Storage Redirection/KVM
then press Enter.
11.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9.
In the SOL/Storage Redirection/KVM menu, select Username and Password then
press Enter. Select Enabled or Disabled then press Enter.
In the SOL/Storage Redirection/KVM menu, select SOL then press Enter. Select
Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
Menu for FW Redirection Configuration
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
69
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
12.
In the SOL/Storage Redirection/KVM menu, select Storage Redirection then press
Enter. Select Enabled or Disabled then press Enter.
14.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select
User Consent then press Enter.
User Opt-in
Opt-in Configurable from Remote IT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< KVM>
< Enabled>
Disabled
Enabled
Configure When User Consent Should be Required.
[] = Move Highlight
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
13.
In the SOL/IDER/KVM menu, select KVM Feature Selection then press Enter. Select
Enabled or Disabled then press Enter.
15.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
[Esc]= Exit
In the User Consent menu, select User Opt-in then press Enter. Select None or KVM
or ALL then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
70
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
16.
In the User Consent menu, select Opt-in Configurable from Remote IT then press
Enter. Select Enabled or Disable Remote Control of KVM Opt-in Policy then press
Enter.
18.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< KVM>
< Enabled>
Disabled
Enabled
[] = Move Highlight
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
17.
In the Intel(R) AMT Configuration menu, select Network Setup then press Enter.
19.
Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select
Password Policy then press Enter.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
In the Intel(R) ME Network Setup menu, select Intel(R) ME Network Name Settings then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Intel (R) ME Network Name Settings
> TCP/ IP Settings
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Step And Configuration
Anytime
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
71
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
20.
In the Intel(R) ME Network Name Settings menu, select Host Name then press
Enter. Enter the computer’s host name then press Enter.
22.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Host Name
[Enter] = Complete Entry
21.
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc]= Discard Changes
23.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Select Dynamic DNS Update then press Enter. Select Enabled or Disabled then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Domain Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
Dedicated
Shared
Select Domain Name then press Enter. Enter the computer’s domain name then press
Enter.
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Select Shared/Dedicated FQDN then press Enter. Select Shared or Dedicated then
press Enter.
_
_
<Shared>
<Disabled>
Disabled
Enabled
[Esc]= Discard Changes
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
72
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
24.
26.
Select Previous Menu until you return to the Intel(R) ME Network Setup menu. Select
TCP/IP Settings then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
TCP/ IP SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Wired LAN IPV4 Configuration
[] = Move Highlight
25.
[Enter] = Select Entry
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[Esc]= Exit
< Enabled>
<Anytime>
<Full Unprovision>
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
In the TCP/IP Settings menu, select Wired LAN IPV4 Configuration then press
Enter.
27.
In the Intel(R) AMT Configuration menu, select Unconfigure Network Access then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
In the Intel(R) AMT Configuration menu, select Activate Network Access then
press Enter.
<Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
< Enabled>
<Anytime>
<Full Unprovision>
Full Unprovision
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
73
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
28.
In the Intel(R) AMT Configuration menu, select Remote Setup And Configuration
then press Enter.
30.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
In the Intel(R) Remote Setup And Configuration menu, select Provisioning Record then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
< Enabled>
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
<Anytime>
_
_
<Full Unprovision>
Provision Record is not present
[ESC] = Exit
[] = Move Highlight
29.
[Enter] = Select Entry
[Esc]= Exit
[] = Move Highlight
31.
In the Intel(R) Remote Setup And Configuration menu, select Current Provisioing
Mode then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
[Enter] = Select Entry
[Esc]= Exit
In the Intel(R) Remote Setup And Configuration menu, select Provisioning server
IPV4/IPV6, enter the Provisioning server address then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
Provisioning Mode:PKI
_
_
Provisioning server address
[ESC] = Exit
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
74
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
32.
In the Intel(R) Remote Setup And Configuration menu, select Provisioning server
FQDN, enter the FQDN of Provisioning server then press Enter.
34.
In the Intel(R) Remote Setup And Configuration menu, select TLS PKI then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[ESC] = Exit
[] = Move Highlight
33.
[Enter] = Select Entry
[ESC] = Exit
[Esc]= Exit
[] = Move Highlight
35.
In the Intel(R) Remote Setup And Configuration menu, select RCFG then press
Enter, and select Start Configuration then press enter.
[Enter] = Select Entry
[Esc]= Exit
In the Intel(R) Remote Configuration menu, select Remote Configuration**
then press Enter, select Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
< Enabled>
_
Disabled
Enabled
[ESC] = Exit
[ESC] = Exit
[] = Move Highlight
[Enter] = Select Entry
[] = Move Highlight
[Esc]= Exit
[Enter] = Select Entry
[Esc]= Exit
75
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
36.
Select PKI DNS Suffix, Enter the PKI DNS Suffix then press Enter.
38.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
_
Enter PKI DNS Suffix
[] = Move Highlight
[Enter] = Select Entry
[] = Move Highlight
[Esc]= Exit
39.
37.
Select Manage Hashes then press Enter, and select one of hash name.
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
In the Intel(R) AMT Power Control menu, select Intel(R) AMT ON in Host Sleep
States then press Enter. Select an option then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
These configurations are effective only after AMT provisioning has started
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
In the Intel(R) AMT Configuration menu, select Power Control then press Enter.
Intel (R) AMT ON in Host Sleep States
< Enabled>
_
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Mobile: ON in S0
Mobile: ON in S0, ME Wake in S3, S4-5 (AC only)
[] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
76
Chapter 6 Intel AMT Settings
www.dfi.com
Chapter 6
40.
In the Intel(R) AMT Power Control menu, select Idle Timeout then press Enter.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
<ENTER> = Complete Entry
41.
[ESC]= Discard Changes
Select Previous Menu until you return to the Main Menu. Select Exit then press Enter.
Type Y then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Exit
[] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
77
Chapter 6 Intel AMT Settings
www.dfi.com
Appendix A
Appendix A - Troubleshooting Checklist
The picture seems to be constantly moving.
Troubleshooting Checklist
1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.
This chapter of the manual is designed to help you with problems that you may encounter
with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple
causes.
2. Move away any objects, such as another monitor or fan, that may be creating a magnetic
field around the display.
Some of the most common things to check when you encounter problems while using your
system are listed below.
The screen seems to be constantly wavering.
3. Make sure your video card’s output frequencies are supported by this monitor.
1. The power switch of each peripheral device is turned on.
1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off.
Fluorescent lights adjacent to the monitor may also cause screen wavering.
2. All cables and power cords are tightly connected.
Power Supply
3. The electrical outlet to which your peripheral devices connected is working. Test the outlet
by plugging in a lamp or other electrical device.
When the computer is turned on, nothing happens.
4. The monitor is turned on.
1. Check that one end of the AC power cord is plugged into a live outlet and the other end
properly plugged into the back of the system.
5. The display’s brightness and contrast controls are adjusted properly.
2. Make sure that the voltage selection switch on the back panel is set for the correct type of
voltage you are using.
6. All add-in boards in the expansion slots are seated securely.
3. The power cord may have a “short” or “open”. Inspect the cord and install a new one if
necessary.
7. Any add-in board you have installed is designed for your system and is set up correctly.
Monitor/Display
Floppy Drive
If the display screen remains dark after the system is turned on:
The computer cannot access the floppy drive.
1. Make sure that the monitor’s power switch is on.
1. The floppy diskette may not be formatted. Format the diskette and try again.
2. Check that one end of the monitor’s power cord is properly attached to the monitor and
the other end is plugged into a working AC outlet. If necessary, try another outlet.
2. The diskette may be write-protected. Use a diskette that is not write-protected.
3. Check that the video input cable is properly attached to the monitor and the system’s
display adapter.
3. You may be writing to the wrong drive. Check the path statement to make sure you are
writing to the targeted drive.
4. Adjust the brightness of the display by turning the monitor’s brightness control knob.
4. There is not enough space left on the diskette. Use another diskette with adequate storage
space.
78
Appendix A Troubleshooting Checklist
www.dfi.com
Appendix A
Hard Drive
System Board
Hard disk failure.
1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is
loose, power off the system, re-install the card and power up the system.
1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS.
2. Check the jumper settings to ensure that the jumpers are properly set.
2. If the system is configured with two hard drives, make sure the bootable (first) hard drive
is configured as Master and the second hard drive is configured as Slave. The master hard
drive must have an active/bootable partition.
3. Verify that all memory modules are seated securely into the memory sockets.
4. Make sure the memory modules are in the correct locations.
Excessively long formatting period.
5. If the board fails to function, place the board on a flat surface and seat all socketed components. Gently press each component into the socket.
If your hard drive takes an excessively long period of time to format, it is likely a cable connection problem. However, if your hard drive has a large capacity, it will take a longer time to
format.
6. If you made changes to the BIOS settings, re-enter setup and load the BIOS defaults.
Serial Port
The serial device (modem, printer) doesn’t output anything or is outputting garbled
characters.
1. Make sure that the serial device’s power is turned on and that the device is on-line.
2. Verify that the device is plugged into the correct serial port on the rear of the computer.
3. Verify that the attached serial device works by attaching it to a serial port that is working
and configured correctly. If the serial device does not work, either the cable or the serial
device has a problem. If the serial device works, the problem may be due to the onboard
I/O or the address setting.
4. Make sure the COM settings and I/O address are configured correctly.
Keyboard
Nothing happens when a key on the keyboard was pressed.
1. Make sure the keyboard is properly connected.
2. Make sure there are no objects resting on the keyboard and that no keys are pressed during the booting process.
79
Appendix A Troubleshooting Checklist
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising