Dfi DT122-SD Manual
DT122-SD
Desktop Box PC
User’s Manual
A45010931
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this
document. Further, the manufacturer reserves the right to revise this publication and make
changes to its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.
•
© 2019. All Rights Reserved.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
LCD/Inverter Power Select..........................................................................................19
Panel Power Select..........................................................................................................20
Copyright.............................................................................................2
Chapter 5 - Ports and Connectors..............................................21
Trademarks..........................................................................................2
Rear Panel I/O Ports......................................................................................................21
FCC and DOC Statement on Class A.........................................2
PS/2 Keyboard/Mouse Port.................................................................. 21
RJ45 LAN Ports.................................................................................. 22
USB Ports......................................................................................... 22
Graphics Interfaces............................................................................ 23
COM (Serial) Ports............................................................................. 24
Audio .............................................................................................. 24
About this Manual.............................................................................4
Warranty ............................................................................................4
I/O Connectors................................................................................................................25
SATA (Serial ATA) Connectors.............................................................. 25
Digital I/O Connector.......................................................................... 25
Digital I/O Power Connector................................................................ 25
Cooling Fan Connectors....................................................................... 26
Power Connectors.............................................................................. 26
LVDS LCD Panel Connector.................................................................. 27
LCD/Inverter Power Connector............................................................. 27
LVDS LCD Panel Connector.................................................................. 27
LCD/Inverter Power Connector............................................................. 27
Chassis Intrusion Connector ............................................................... 28
Front Panel Connector........................................................................ 28
SMBus Connector .............................................................................. 29
S/PDIF Connector............................................................................... 29
LPC Connector................................................................................... 30
Battery............................................................................................. 30
Expansion Slots................................................................................. 31
Static Electricity Precautions...........................................................4
Safety Measures..................................................................................4
Safety Precautions..............................................................................5
About the Package............................................................................5
Before Using the System.................................................................5
Chapter 1 - Introduction.................................................................6
Overview...........................................................................................................................6
Key Features.....................................................................................................................6
Specifications.....................................................................................................................7
Getting to Know the DT122-SD ...............................................................................8
Mechanical Dimensions..................................................................................................9
Motherboard Dimensions ............................................................................................9
Chapter 6 - Mounting Options......................................................32
Chapter 7 - BIOS Setup...................................................................34
Overview ..........................................................................................................................34
Insyde BIOS Setup Utility................................................................... 35
Chapter 2 - Getting Started...........................................................10
Main.....................................................................................................................................35
Advanced ..........................................................................................................................35
Security..............................................................................................................................42
Boot....................................................................................................................................44
Chapter 3 - Installing Devices........................................................11
Opening
Installing
Installing
Installing
the chassis........................................................................................................11
a 2.5" or 3.5" SATA Drive...........................................................................12
a PCIe Expansion Card.................................................................................15
a Mini PCI Expansion Card..........................................................................16
Exit.................................................................................................. 45
Updating the BIOS..........................................................................................................45
Notice: BIOS SPI ROM...................................................................................................46
Chapter 8 - Supported Software...................................................47
Chapter 4 - Jumper Settings...........................................................17
Chapter 9 - RAID (Only for Intel® Q170 Chipset)..................64
Clear CMOS Data...........................................................................................................17
Backlight Power Select...................................................................................................17
COM1/COM2 RS232/Power Select............................................................................18
Power-on Select...............................................................................................................18
Mini PCIe Signal Select .................................................................................................19
Chapter 10 - Intel AMT Settings (Only for Intel® Q170 Chipset) 68
Appendix A - Troubleshooting Checklist.....................................81
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
2. Wear an antistatic wrist strap.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 DT122-SD system unit
• 1 HDD drive bay kit
• 1 CD disk includes
- Manual
- Drivers
• 1 Quick Installation Guide
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Optional Items
• Keep this system away from humidity.
• Power Cord
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
Before Using the System
Before powering-on the system, prepare the basic system components.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
If you are installing the system board in a new system, you will need at least the following
internal components.
• If one of the following occurs, consult a service personnel:
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
- The power cord or plug is damaged.
- Liquid has penetrated the system.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview
Model Name
DT122-SD
Processor
6th Generation Intel® CoreTM processors
Chipset
Intel® H110/Q170 chipset
LAN
2 LAN ports
COM
1 COM port
Displays
1 DP++, 1 DVI-I, 1 VGA
USB
2 USB 2.0 ports
4 USB 3.0 ports
Audio
Mic-in, Line-out
Front View
Rear View
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
Processor System
I/O Ports
• Processors:
6th Generation Intel® CoreTM Processors, LGA 1151 Socket
Intel® CoreTM i7-6700TE, Quad Core, 8M Cache, 2.4GHz (3.4GHz), 35W
Intel® CoreTM i5-6500TE, Quad Core, 6M Cache, 2.3GHz (3.3GHz), 35W
Intel® CoreTM i3-6100TE, Dual Core, 4M Cache, 2.7GHz, 35W
Intel® Pentium® G4400TE, Dual Core, 3M Cache, 2.4GHz, 35W
Intel® Celeron® Processor G3900TE, Dual Core, 2M Cache, 2.6GHz, 35W
7th Generation Intel® CoreTM Processors, LGA 1151 Socket
Intel® CoreTM i7-7700T, Quad Core, 8M Cache, 2.9GHz (3.8GHz), 35W
Intel® CoreTM i5-7500T, Quad Core, 6M Cache, 2.7GHz (3.3GHz), 35W
Intel® CoreTM i3-7101TE, Dual Core, 3M Cache, 3.4GHz, 35W
Intel® Celeron® Processor G3930TE, Dual Core, 2M Cache, 2.7GHz, 35W
2 x USB 2.0
- 1 x PS/2 (mini-DIN-6)
- 1 x VGA
- 1 x DVI-I (DVI-D signal)
- 1 x DP++
•Chipset:
Intel® Q170/H110 Express chipset
Memory
• 2 x 260-pin SODIMM up to 32GB
• Dual Channel DDR4 1866/2133MHz
Graphics
• Intel® HD Gen 9 Graphics
• OpenGL 5.0, DirectX 12, OpenCL 2.1
- Mic-in and line-out jack
Environment
• Temperature
- Operating: 0oC~45oC
- Storage: -20oC~60oC
• Humidity
- 0 to 90% RH (non-condensing)
• Operating Vibration
- IEC68-2-64
• Operating Shock
- Operating: 3G peak acceleration (11 msec. duration)
- Non-operating: 5G peak acceleration (11 msec. duration)
Construction
• Front Bezel aluminum + Chassis Sheet Metal
Dimensions
• 300mm x 75mm x 217mm (W x H x D)
Mounting
Wall mount
Weight
• 3.7 kg
OS Support
Windows 7 (/WES7) 32/64-bit
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise 64-bit
STANDARDS AND
CERTIFICATIONS
• Shock
Operating: 3G
Non-operating: 5G
• Vibration
Operating: Random 5~500Hz 1G
Non-operating: Sweep Sine 10~500Hz 1.5G
• Package Drop
ISTA Project 1A
• CE/FCC (to be applied)
Other Features
• Watchdog Timer function; System Reset, programmable via software from 1 to
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
• Displays: 1 x VGA (resolution up to 1920x1200@60Hz), 1 x DVI-I (DVI-D signal,
resolution up to 1920x1200@60Hz), 1 x DP++ (resolution up to 4096x2304@60Hz)
• Triple Displays: VGA + DVI-I (DVI-D signal) + DP++ (H110 supports dual displays)
Storage
1 x 3.5" or 2 x 2.5" SATA 3.0 Drive Bay (1 x 2.5" by default)
Ethernet
With Intel® Q170 chipset:
1 x Intel® I210AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps) (only Core i7/i5 supports
iAMT)
With Intel® H110 chipset:
1 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219V PCIe (10/100/1000Mbps)
Expansion Slots
1 x PCIe x16 (Gen 3) or 1 x PCI (through optional riser card)
Q170:
1 x full-size Mini PCIe (mSATA/PCIe, PCIe by default)
H110:
1 x full-size Mini PCIe (PCIe only)
Audio
Realtek ALC888S-VD2-GR
Power
• Power type
- Flex ATX 250W
• DC-in External Power Adapter (available upon request)
Cooling System
1 x System Fan
1 x CPU Fan
• Front Panel
- 1 Power button
- 1 Reset button
- 2 LED indicators: Power, HDD
• Rear Panel
- 2 x GbE (RJ-45)
- 1 x RS-232 (DB-9)
- 4 x USB 3.0
Debian 8 (with VESA graphic driver)
CentOS 7 (with VESA graphic driver)
Ubuntu 15.10 (Intel graphic driver available)
255 Seconds
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the DT122-SD
Front View
Rear View
Reset Button
COM 1
Power LED
LAN 1 LAN 2
DVI-I
PS/2 KB/MS
Power Button
HDD LED
VGA
USB 2.0
DP++
Mic-in
USB 3.0 Line-out
Power Button
Press to power on or power off the system.
DVI-I Port (DVI-D signal)/VGA/DP++
Used to connect to the DVI-I connector/VGA connector/DisplayPort of an LCD monitor.
Reset Button
Press to reset the system.
COM 1 Port
Used to connect serial devices.
HDD LED
Indicates the status of the hard drive.
USB Ports
Used to connect USB 3.0/2.0/1.1 devices.
Power LED
Indicates the power status of the system.
LAN Ports
Used to connect the system to a local area network.
Line-out
Used to connect a speaker.
Mic-in
Used to connect an external microphone.
PS/2 KB/Mouse
Used to connect a PS/2 keyboard or a PS/2 mouse.
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
Motherboard Dimensions
0
6.17
11.89
37.64
73.98
104.24
126.74
145.91
163.65
170.00
0
Rear View
217.20
33.02
Left View
110.38
Right View
74.00
78.00
300.00
140.78
Front View
18.02
71.51
165.10
170.00
9
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
•
•
•
•
SATA hard drive
AC power adapter
PS/2 or USB keyboard
PS/2 or USB mouse
CD-ROM drive (for installing software/drivers)
Screwdriver
Memory module (optional)
Installing Devices
The following are devices that can be installed in the system.
•
•
Memory module
SATA hard drive
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1.
2.
Power-on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing the Operating System
Most operating system software are provided in a CD therefore you need to install a CD-ROM
drive in order to use the CD.
Make sure a SATA drive is already installed.
1.
2.
Refer to the following chapters for information on connecting a CD-ROM drive and installing a SATA drive.
Refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
10
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing Devices
Import:
To prevent damage to the system board, power down the system and remove all AC
power cords before opening the chassis cover.
4.
Slide the cover backwards to open the system.
5.
The DIMM sockets and SATA drive bay are readily accessible after removing the
chassis cover.
Opening the chassis
1.
Make sure the system and all other peripheral devices connected to it have been
powered off.
2.
Disconnect all power cords and cables.
3.
The 4 mounting screws on the sides of the system are used to secure the cover to the
chassis. Remove these screws and then put them in a safe place for later use.
Mounting
screw
2.5"/3.5" SATA
drive bay
DIMM socket
Mounting
screw
11
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a 2.5" or 3.5" SATA Drive
3.
Use the provided mounting screws to attach the HDD bracket to the drive bay.
Installing a 2.5” SATA Drive
Mounting screws
1.
Drive bay
(bottom side)
Remove the 6 mounting screws that secure the drive bay to the system.
Mounting holes
Mounting screw
Drive bay
4.
Place the SATA drive bay back in the chassis and install the SATA drive bay using the
mounting screws you removed in step 1.
Mounting screw
Mounting screw
2.
Align the mounting holes on the SATA drive with the mounting holes on the HDD bracket
and use the mounting screws provided in the drive bay kit to secure the drive in place.
Mounting screw
Mounting screws
Mounting screw
Mounting screw
SATA drive
HDD bracket
Mounting screw
12
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
5.
Connect the SATA data and power cable to the SATA drive.
SATA
power/data
cable
SATA connector
13
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
lnstalling a 3.5" SATA Drive
1.
3.
Align the mounting holes on the SATA drive with the mounting holes on the drive bay;
then use the provided mounting screws to install the SATA drive on the drive bay.
Remove the 6 mounting screws that secure the drive bay to the system.
Mounting screw
Mounting screw
Mounting screw
Drive bay
Drive bay
Mounting screw
4.
Mounting screw
2.
Place the drive bay back in the chassis and install the drive bay using the mounting
screws you removed in step 1.
Insert the spacers provided in HDD drive bay kit to the anti-shock bumper.
Mounting screw
Spacer
Spacer
Mounting screw
Drive bay
Mounting screw
14
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a PCIe Expansion Card
2.
Take off the shielding plate.
Important:
When inserting the riser card,
please select a card within
175mm.
Shielding plate
Mounting bracket and
mounting screw
1.
The PCIe x16 on the motherboard is used to insert a PCIe expansion card.
To install an expansion card, you need to remove the mounting screw that secure the
bracket to the chassis. Put the screw and the bracket in a safe place for later use.
Mounting screw
PCIe expansion slot
Mounting bracket
15
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
3.
Installing a Mini PCI Expansion Card
Insert the expansion card and secure it in place using the mounting bracket and screw that
you removed in step 1.
The system board is equipped with 1 full-size Mini PCIe slot that can accommodate a Mini PCIe
card or an mSATA card depending on the model. Here we will demonstrate the installation of a
full-size Mini PCIe card.
1.
2.
Mounting bracket
and mounting screw
Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card
with the notch in the connector on the system board.
Push the Mini PCIe card down and use the provided mounting screw to secure the card on
the system board.
Rear view
Mounting Screw
Note:
The expansion card used in the above illustrations may not resemble the actual cards.
These illustrations are for reference only.
16
Chapter 3 Installing Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
Clear CMOS Data
Backlight Power Select
JP3
1
2
3
JP4
1-2 On:
Normal (default)
1
2
3
1-2 On: +3.3V
(default)
1
2
3
1
2
3
2-3 On:
Clear CMOS Data
2-3 On: +5V
If you encounter the following situations, you can reconfigure the system with the default
values stored in the ROM BIOS.
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
JP3 is used to select the power level of backlight brightness control: +3.3V or +5V.
To load the default values stored in the ROM BIOS, please follow the steps below.
1. Power off the system and unplug the power cord.
Important:
Before powering on the system, make sure that the power settings of JP3 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
2. Set JP4 pins 2 and 3 to On. Wait for a few seconds and set JP4 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
17
Chapter 2
Installation
4 Hardware
Jumper Settings
www.dfi.com
Chapter 4
COM1/COM2 RS232/Power Select
2
4
6
1
3
5
1
3
5
2
4
6
1-3 (RI), 2-4 (DCD) On: 3-5 (+5V), 4-6 (+12V) On:
RS232 with power
RS232 (default)
JP6
(COM 1)
10
9
2
1
Power-on Select
2 4 6
1 3 5
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
JP5
2 4 6
1 3 5
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
1 2 3
1-2 On:
Power-on via power button
(default)
JP8
(COM 2)
1 2 3
2-3 On:
Power-on via AC power
COM 2
COM 1
JP5 is used to select the method of powering on the system. If you want the system to
power-on whenever AC power comes in, set JP5 pins 2 and 3 to On. If you want to use the
power button, set pins 1 and 2 to On.
JP6 (for COM 1) and JP8 (for COM 2) are used to configure the Serial COM ports to pure
RS232 or RS232 with power. The pin functions of COM 1 and COM 2 will vary according to
JP6’s and JP8’s settings respectively.
When using JP5 “Power On” feature to power the system back on after a power failure occurs,
the system may not power on if the power lost is resumed within 5 seconds (power flicker).
18
Chapter 2
Installation
4 Hardware
Jumper Settings
www.dfi.com
Chapter 4
Mini PCIe Signal Select
LCD/Inverter Power Select
JP2
JP1
1 2 3
1 2 3
1-2 On:
+12V (default)
1 2 3
1-2 On:
Mini PCIe (default)
2-3 On: +5V
1 2 3
2-3 On: mSATA
(only with Intel® Q170 chipset)
JP1 is used to select the Mini PCIe signal.
JP2 is used to select the power level of LCD inverter connector.
19
Chapter 2
Installation
4 Hardware
Jumper Settings
www.dfi.com
Chapter 4
Panel Power Select
2 4 6
JP7
1 3 5
1-2 On: +12V
2 4 6
1 3 5
3-4 On:+5V
2 4 6
1 3 5
5-6 On: +3.3V
(default)
JP7 is used to select the power supplied with the LCD panel.
Important:
Before powering-on the system, make sure that the power settings of JP7 match the
LCD panel’s specification. Selecting the incorrect voltage will seriously damage the
LCD panel.
20
Chapter 2
Installation
4 Hardware
Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
Rear Panel I/O Ports
PS/2 Keyboard/Mouse Port
PS/2 Keyboard/Mouse
PS/2 KB/MS
USB 2.0*2
COM 1
VGA
DVI-I
DP++
LAN 1
LAN 2
USB 3.0*4
Line-out
Mic-in
The rear panel I/O ports consist of the following:
•
•
•
•
•
•
•
•
•
•
2
1
4
2
1
1
1
1
1
1
x
x
x
x
x
x
x
x
x
x
GbE (RJ-45)
RS-232 (DB-9)
USB 3.0
USB 2.0
PS/2 Keyboard/Mouse port
VGA
DVI-I (DVI-D signal)
DP++
Line-out
Mic-in
This rear I/O port is used to connect a PS/2 keyboard/mouse.
Wake-On-PS/2 Keyboard/Mouse
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power on the system.
Important:
The +5V_standby power source of your power supply must support ≥720mA.
21
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
USB Ports
VCC
-Data1
+Data1
GND
N. C.
RJ45 LAN Ports
LAN 1
10
9
VCC
-Data0
+Data0
GND
Key
2
1
LAN 2
USB 2.0
®
USB 7-8 USB 11-12(Only with Intel Q170
chipset)
LAN 1
LAN 2
USB 6
USB 5
USB 2.0
Features
USB 2
USB 4
For Intel H110 Chipset :
®
•
•
USB 1
USB 3
Intel® I211AT PCIe
Intel® I219V PCIe
USB 3.0
USB 3.0
For Intel® Q170 Chipset:
•
•
Intel® I210AT PCIe
Intel® I219LM PCIe with iAMT11.0
The two LAN ports allow the system board to connect to a local area network with a network
hub.
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
BIOS Setting
The system board is equipped with four onboard USB 3.0 ports (USB 1-2/3-4) and two onboard USB 2.0 ports (USB 5-6). The 9-pin connector allows you to connect 2 additional USB
2.0/1.1 ports: USB 7-8 and USB 11-12 (Only with Intel® Q170 chipset).
Configure the onboard LAN ports in the Advanced menu (“ACPI Configuration” submenu) of
the BIOS. Refer to Chapter 7 - BIOS for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 8 - Supported Software for more information.
22
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Graphics Interfaces
BIOS Setting
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to Chapter 7 - BIOS for more information.
The display ports consist of the following:
•
•
•
Driver Installation
You may need to install the proper drivers in your system operation to use the USB device.
Refer to your operating system’s manual or documentation for more information.
1 VGA port
1 DP++ port
1 DVI-I port
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
VGA
DVI-I
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
DP
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
DP Port
The DisplayPort is a digital display interface used to connect a display device such as a computer monitor. It is used to transmit audio and video simultaneously. The interface, which is
developed by VESA, delivers higher performance features than any other digital interfaces.
DVI-I Port
The DVI-I port is used to connect an LCD monitor. This port supports DVI-D signal only.
Connect the display device’s cable connector to the DVI-I port. After plugging the cable connector into the port, gently tighten the cable screws to hold the connector in place.
Driver Installation
Install the graphics driver. Refer to Chapter 8 - Supported Software for more information.
23
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
COM (Serial) Ports
Audio
COM 1
COM 1 : RS232
Rear audio
10 9
RI-
N.C
CTSDSRDTRRD
Line-out
RTSGND
TD
DCD2
Mic-in
1
COM 2 : RS232/422/485
COM 3/4 : RS232
Rear Audio
The system board is equipped with 2 audio jacks.
COM 1, COM 3 and COM 4 are fixed at RS232 whereas COM 2 can be selected among
RS232/422/485 using the BIOS setup utility.
•
Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
The pin functions of COM port 1 and 2 will vary according to JP6’s and JP8’s jumper settings
respectively. JP6 and JP8 allow you to configure RS232 power voltage of COM port 1 and 2.
Refer to “COM1/COM2 RS232 Power Select” in this chapter for more information.
•
Mic-in Jack (Pink)
This jack is used to connect an external microphone.
BIOS Setting
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
Configure the audio settings in the Advanced menu (“Audio Configuration” submenu) of the
BIOS. Refer to Chapter 7 - BIOS for more information.
BIOS Setting
Driver Installation
Configure the COM ports 1/2/3/4 in the Advanced menu (“SIO NUVOTON6106D” submenu) of
the BIOS. Refer to Chapter 7 - BIOS for more information.
Install the audio driver. Refer to Chapter 8 - Supported Software for more information.
24
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
I/O Connectors
Digital I/O Connector
SATA (Serial ATA) Connectors
Digital I/O Power Connector
SATA 3.0 6Gb/s
SATA 0
SATA 2
SATA 3
Digital I/O
1
Digital I/O power
GND
RXP
RXN
GND
TXN
TXP
GND
7
1
+12V
Ground
5VSB
+5V
1
4
Features
•
•
The 8-bit Digital I/O connector provides the ability of monitoring and control of the connected
external devices.
3 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s (SATA 0, SATA 2 and SATA 3)
Supports RAID 0/1 with Intel® Q170 chipset
Digital I/O Connector
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
BIOS Setting
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 - BIOS for more information.
Pins
Function
1
DIO7
2
DIO6
3
DIO5
4
DIO4
5
DIO3
6
DIO2
7
DIO1
8
DIO0
25
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Cooling Fan Connectors
Power Connectors
ATX power
Ground
12V
PRM
CTRL
+3.3V
+12V
+12V
+5VSB
PWR_OK
GND
+5V
GND
+5V
GND
+3.3V
+3.3V
1
4
CPU Fan
Ground
12V
FAN IN
1
1
System Fan 2
12 24
GND
+5V
+5V
+5V
NC
GND
GND
GND
PS_ON#
GND
-12V
+3.3V
1
System Fan 1
13
+12V Power
FAN IN
12V
Ground
Ground
+12V
Ground
+12V
The fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1.
An ATX12V power supply unit has a standard 24-pin ATX main power connector that must be
inserted into the 24-pin connector. The 4-pin +12V power connector enables the delivery of
more +12VDC current to the processor’s Voltage Regulator Module (VRM).
BIOS Setting
The Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS will display the current
speed of the cooling fans. Refer to Chapter 7 - BIOS for more information.
The power connectors from the power supply unit are designed to fit the 24-pin and 4-pin
connectors in only one orientation. Make sure to find the proper orientation before plugging
the connectors.
26
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
LVDS LCD Panel Connector
LVDS LCD Panel Connector
LCD/Inverter Power Connector
Pins
2
40
39
LVDS LCD
panel
1
1
8
LCD/Inverter
power
Function
Pins
LCD/Inverter Power Connector
Function
Pins
Function
1
GND
2
GND
1
GND
3
LVDS_Out3+ (Odd_3+)
4
LVDS_Out7+ (Even_3+)
2
GND
5
LVDS_Out3- (Odd_3-)
6
LVDS_Out7- (Even_3-)
3
Panel Inverter Brightness Voltage Control
7
GND
8
GND
4
Panel Power
9
LVDS_Out2+ (Odd_2+)
10
LVDS_Out6+ (Even_2+)
5
+3.3V
11
LVDS_Out2- (Odd_2-)
12
LVDS_Out6- (Even_2-)
6
Panel Backlight On/Off Control
13
GND
14
GND
7
+12V
15
LVDS_Out1+ (Odd_1+)
16
LVDS_Out5+ (Even_1+)
8
+12V
17
LVDS_Out1- (Odd_1-)
18
LVDS_Out5- (Even_1-)
19
GND
20
GND
21
LVDS_Out0+ (Odd_0+)
22
LVDS_Out4+ (Even_0+)
23
LVDS_Out0- (Odd_0-)
24
LVDS_Out4- (Even_0-)
The system board allows you to connect a LCD Display Panel by means of the
LVDS LCD panel connector and the LCD/Inverter power connector. These connectors transmit video signals and power from the system board to the LCD
Display Panel.
25
GND
26
GND
27
LVDS_CLK1+ (Odd_CLK+)
28
LVDS_CLK2+ (Even_CLK+)
Refer to the right side for the pin functions of these connectors.
29
LVDS_CLK1- (Odd_CLK-)
30
LVDS_CLK2- (Even_CLK-)
BIOS Setting
31
GND
32
GND
Configure the LCD panel in the Advanced menu (“Video Configuration” submenu) of the BIOS. Refer to Chapter 7 - BIOS for more information.
33
DDC_CLK
34
NC
35
DDC_DATA
36
NC
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
Note:
DFI board's LVDS connector: Hirose DF13-40DP-1.25V(91)/40P/1.25mm; cable side
connector: Hirose DF13-40DS-1.25C.
27
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Chassis Intrusion Connector
Front Panel Connector
Front
Panel
1 2
PWR-LED
HDD-LED
ATX-SW
RESET-SW
1 2
11 12
Signal
Ground
Chassis
Intrusion
HDD-LED - HDD LED
This LED will be lit when the hard drive is being accessed.
The board supports the chassis intrusion detection function. Connect the chassis intrusion
sensor cable from the chassis to this connector. When the system’s power is on and a chassis
intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion
event occurs, the alarm will sound only after the system restarts.
RESET-SW - Reset Switch
This switch allows you to reboot without having to power off the system.
ATX-SW - ATX Power Switch
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
Pin Pin Assignment
HDD-LED
RESET SW
3
HDD Power
5
Signal
7
Ground
9
RST Signal
11
N.C.
Pin Pin Assignment
2
LED Power
PWR-LED 4
LED Power
ATX-SW
6
Signal
8
Ground
10
Signal
28
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
SMBus Connector
12
GND
SMBUS_Data
SMBus
1
56
+5V
NC
SPOUT
Ground
SPIN
3V3SB
SMBUS_CLK
SMBUS_Alert
S/PDIF Connector
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
5
S/PDIF
S/PDIF (Sony/Philips Digital Interface Format), a type of digital audio connector, is used for
digital audio transmission or output.
29
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
LPC Connector
Battery
LPC
14 13
Battery
2 1
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components within the system, which are typically provided by a Super I/O controller. Furthermore,
it can be used to interface firmware hubs, Trusted Platform Module (TPM) devices and embedded controller solutions. Data transfer on the LPC bus is implemented over a 4 bit serialized
data interface, which uses a 33MHz LPC bus clock. For more information about LPC bus refer
to the Intel® Low Pin Count Interface Specification Revision 1.1’. The table below indicates the
pin function of the LPC connector.
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
Pins
Pin Assignment
Pins
• Replace only with the same or equivalent type recommend by the manufacturer.
Pin Assignment
1
L_CLK
2
L_AD1
3
L_RST#
4
L_AD0
5
L_FRAME#
6
3V3
7
L_AD3
8
GND
9
L_AD2
10
Kev
11
INT_SERIRQ
12
GND
13
5VSB
14
5V
• Dispose of used batteries according to local ordinance.
30
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Expansion Slots
Mini PCI Express
PCI Express x16
PCI Express x16 (Gen 3) Slot
Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into the
PCI Express x16 slot. To install a graphics card into the x16 slot, align the graphics card above
the slot then press it down firmly until it is completely seated in the slot. The retaining clip of
the slot will automatically hold the graphics card in place.
Mini PCI Express Slot
The Mini PCIe socket is used to install a Mini PCIe card. You can use JP1 to select the Mini
PCIe signal between PCIe and mSATA (with Intel® Q170 chipset only). (Refer to Chapter 4 Jumper Settings for more information.) When the mSATA signal is selected, this slot can be
used for capacity expansion.
31
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 6
Chapter 6 - Mounting Options
2.
Wall Mount
Use the mounting screws removed in step 1 to secure the wall mount brackets on each
side of the system.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
Wall mount bracket
There are 2 types of wall mount brackets:
•
Type A
Wall mount bracket
Mounting screw
•
Type B
Type A wall mount kit includes:
•
2 type A wall mount brackets
1.
If the mounting screws have been previously attached to the top cover of the system,
please remove them first.
Mounting screw
Ø8.50
74.00
78.00
Ø5.00
Ø3.60
300.00
4.00
180.00
16
16
2
4-#6-32
Ø4.00
2
Mounting screw
120.00
80.00
160.00
28.60
319.00
32
Chapter 6 Mounting Options
www.dfi.com
Chapter 6
Type B wall mount kit includes:
•
2 type B wall mount brackets
•
Bracket screws
55.00
40.00
5.00
The 4 mounting holes on the sides of the system are used to mount the wall mount
brackets.
R2.50
Mounting screw
2.
R2.50
37
55.00
40.00
R2.50
16
5.00
300.00
335.00
360.00
40.00
55.00
78.00
Ø8.50
5.00
4.00
1.
Use the provided mounting screws to secure the wall mount brackets on each side of the
system.
Wall mount bracket
Wall mount bracket
33
Chapter 6 Mounting Options
www.dfi.com
300.
335.
360.
Chapter 7
Chapter 7 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or fields.
<Esc>
Exit to the BIOS Setup Utility.
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup Defaults
<F10>
Save and Exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
34
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Project Name
BIOS Version
SD100
63.31Q
Processor Type
EC Ver:
CPUID:
CPU Speed:
CPU Stepping:
L1 Data Cache:
L1 Instruction Cache:
L2 Cache:
L3 Cache:
Number of Processors:
Microcode Rev:
Intel(R) Core(TM) i5-6500TE CPU @ 2.30GHz
N/A
0x506E3 (SKYLAKE DT HALO)
2300 MHz
03 (R0/S0 Stepping)
32 KB
32 KB
256 KB
6144 KB
4 Core(s) / 4 Thread(s)
0000006A
Total Memory
System Memory Speed
Channel A
SODIMM 0
Unknown 1
Channel B
Unknown 0
Unknown 1
4096 MB
2133 MHz
PCH Rev / SKU
Intel ME Version / SKU
31 (D1 Stepping) / SKL PCH-H Q170
11.0.0. 1180 / CORPORATE
System Time
System Date
[21:12:02]
[15/4/2016]
F1 Help
Esc Exit
Important:
Setting incorrect field values may cause the system to malfunction.
Rev. 5.0
This is the help for the
hour, minute, second
field. Valid range is from
0 to 23, 0 to 59, 0 to 59.
INCREASE/REDUCE:
+/-.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
ACPI Configuration Setting
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
MEBX Configuration
 Active Management Technology Support
 SIO NUVOTON6106D








4096 MB
[Not Installed]
[Not Installed]
[Not Installed]
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1980 to 2099.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to
23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
35
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ACPI Settings
CPU Configuration
This section configures the system ACPI parameters.
This section configures the CPU.
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
Determines the action taken when the system power
is off and a PCI Power
Management Enable wake
up event occurs.
ACPI Configuration
Wake on LAN
After G3
F1 Help
Esc Exit
Rev. 5.0
Advanced
<Enabled>
<S0 State>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
CPU Configuration
Intel(R) SpeedStep(tm)
Turbo Mode
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enabled>
<Enabled>
F5/F6 Change Values
Enter Select  SubMenu
Allows more than two frequency ranges to be supported.
F9 Setup Defaults
F10 Save and Exit
Wake on LAN
Intel SpeedStep®
This field use to enable or disable the LAN signal to wake up the system.
Enable or disable the Enhanced Intel SpeedStep® Technology, which helps optimize
the balance between system’s power consumption and performance. After it is enabled
in the BIOS, you can enable the EIST feature using the operating system’s power
management.
After G3
This field is to specify what state what state the system should be in when power is
re-applied after a power failure (G3, the mechanical-off, state).
S0 State
The system is in working state.
S5 State
The system is in soft-off state.
Turbo Mode
Enable or disable processor turbo mode (requires that EMTTM is enabled too), which
allows the processor core to automatically run faster than the base frequency when
the processor’s power, temperature, and specification are within the limits of TDP.
Note:
For the “After G3” setting to take effect, make sure that the "AC Power Loss” option is set to “Always on” in “SIO NUVOTON6106D” of the “Advanced” menu.
36
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Panel Color Depth
Video Configuration
Select the LFP panel color depth: 18 bit, 24 bit, 36 bit, and 48 bit.
This section configures the video settings.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Video Configuration
Internal Graphics
Always Enabled PEG
Boot display
Panel Color Depth
LVDS Support
LCD Panel Type
<Auto>
<Disabled>
<VGA+DVI>
<18 Bit>
<Disabled>
<1024x768>
LVDS Support
Keep IGFX enabled based
on the setup options.
Turn on/off LVDS.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Backlight Type Setting
Video Configuration
Internal Graphics
Always Enabled PEG
Boot display
Panel Color Depth
LVDS Support
LCD Panel Type
<Auto>
<Disabled>
<VGA+DVI>
<18 Bit>
<Disabled>
<1024x768>
LCD Panel Type
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
800x480
800x600
1024x768
1366x768
1280x1024
1920x1080
Internal Graphics
Keep IGFX enabled or disabled based on the setup options.
F1 Help
Esc Exit
Always Enabled PEG
Enable or disable the PEG function.
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
LCD Panel Type
Boot display
Select the type of LCD panel connected to the system’s LCD connector. Please check
the specifications of your LCD monitor.
Set the display device combination during system booting.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Video Configuration
Internal Graphics
Always Enabled PEG
Boot display
Panel Color Depth
LVDS Support
LCD Panel Type
F1 Help
Esc Exit
Boot display
LCD+DVI
LCD+VGA
LCD+DP
DVI+LCD
DVI+VGA
DVI+DP
VGA+LCD
VGA+DVI
VGA+DP
DP+LCD
DP+DVI
DP+VGA
↑/↓ Select Item
←/→ Select Item
<Auto>
<Disabled>
<VGA+DVI>
<18 Bit>
<Disabled>
<1024x768>
F5/F6 Change Values
Enter Select  SubMenu
Chose display device combination
F9 Setup Defaults
F10 Save and Exit
37
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Audio Configuration
SATA Configuration
This section configures the audio settings.
This section configures the SATA controller.
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
HD Audio
Control Detection of the
HD-Audio device.
<Enabled>
SATA Controller(s)
SATA Mode Selection
Serial ATA Port 0
Port 0
Serial ATA Port 1
Port 1
Serial ATA Port 2
Port 2
Serial ATA Port 3
Port 3
Disabled = HDA will be
unconditionally disabled
Enabled = HDA will be
unconditionally enabled
Auto = HDA will be enabled if present, disabled
otherwise.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Rev. 5.0
Advanced
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
<Enabled>
<AHCI>
[ST4000NM0033-9ZM170 ]
<Enabled>
[Not Installed]
<Enabled>
[Not Installed]
<Enabled>
[Not Installed]
<Enabled>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Enable/Disable SATA
Device.
F9 Setup Defaults
F10 Save and Exit
SATA Controller(s)
HD Audio
Enable or disable Serial ATA devices.
Control the detection of high-definition audio devices.
SATA Mode Selection
Disabled
HDA will be unconditionally disabled.
Enabled
HDA will be unconditionally enabled.
Auto
HDA will be enabled if present, disabled otherwise.
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
RAID Mode (only with Intel® Q170 chipset)
This option allows you to configure RAID on the Serial ATA devices .
Serial ATA Port 0, 1, 2, and 3
Enable or disable the serial ATA port.
38
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
USB Configuration
This section configures the parameters of the USB devices.
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
USB BIOS Support
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
Rev. 5.0
Advanced
USB keyboard/mouse/storage support under UEFI
environment.
<Enabled>
F5/F6 Change Values
Enter Select  SubMenu
PCI Express Root Port 9
PCIe Speed
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
USB BIOS Support
<Enabled>
<AUTO>
F5/F6 Change Values
Enter Select  SubMenu
InsydeH20 Setup Utility
Disabled
Disable USB keyboard/mouse/storage support.
Control the PCI Express
Root Port.
F9 Setup Defaults
F10 Save and Exit
Rev. 5.0
Advanced
PCI Express Root Port 10
PCIe Speed
Enabled
Enable the support of USB keyboard/mouse/storage under UEFI and DOS environment.
<Enabled>
<AUTO>
Control the PCI Express
Root Port.
PCI Express Configuration
This section configures the PCI Express root ports.
InsydeH20 Setup Utility
Rev. 5.0
Advanced


PCI Express Root Port 9
Settings.
PCI Express Root Port 9
PCI Express Root Port 10
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
PCI Express Root Port
Enable or disable the PCI Express Root Port.
PCIe Speed
Select the speed of the PCI Express Root Port: Auto, Gen1, Gen2 or Gen3.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
39
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ME Configuration
SIO NUVOTON6106D
This section configures settings of flashing the Intel® Management Engine firmware.
This section configures the system’s super I/O chip parameters.
InsydeH20 Setup Utility
InsydeH20 Setup Utility
Rev. 5.0
Me Fw Image Re-Flash
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
Rev. 5.0
Advanced
Advanced
<Disabled>
F5/F6 Change Values
Enter Select  SubMenu
Enable/disable to flash ME
region
SYS Smart Fan Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
CPU Smart Fan Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
SYS Smart Fan 2 Control
Boundary 1
Boundary 2
Boundary 3
Boundary 4
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
[30]
[40]
[50]
[75]
<Enable>
[30]
[40]
[50]
[60]
F5/F6 Change Values
Enter Select  SubMenu
Enable/Disable Smart Fan
F9 Setup Defaults
F10 Save and Exit
Me Fw Image Re-Flash
Enable or disable flashing of the Intel® Management Engine firmware.
SYS/CPU Smart Fan/Fan 2 Control
Enable or disable the system/CPU smart fan or fan 2.
Boundary 1 to Boundary 4
Set the boundary temperatures that determine the operation of the fan with different fan speeds accordingly. For example, when the system or the CPU temperature
reaches boundary temperature 1, the system or CPU fan should be turned on and
operate at the designated speed.
The range of the temperature is from 0 to 127oC.
Fan Speed Count 1 to Fan Speed Count 4
Set the fan speed. The range is from 0 (fan stop)-100% (full speed).
40
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
InsydeH20 Setup Utility
Rev. 5.0
InsydeH20 Setup Utility
Advanced
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
COM Port 1
Base I/O Address
Interrupt
COM Port 2
Base I/O Address
Interrupt
Type
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
WDT
Case Open
AC Power Loss
PC Health Status
F1 Help
Esc Exit
Rev. 5.0
Advanced
[30]
[40]
[50]
[75]
<Enable>
<3F8>
<IRQ3>
<Enable>
<2F8>
<IRQ4>
<RS232>
<Enable>
<3E8>
<IRQ3>
<Enable>
<2E8>
<IRQ4>
<Disable>
<Disable>
<Always off>
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Fan Speed Count 1
Fan Speed Count 2
Fan Speed Count 3
Fan Speed Count 4
COM Port 1
Base I/O Address
Interrupt
COM Port 2
Base I/O Address
Interrupt
Type
COM Port 3
Base I/O Address
Interrupt
COM Port 4
Base I/O Address
Interrupt
WDT
Case Open
AC Power Loss
PC Health Status
Configure Serial port using
options: [Disable] No Configuration [Enable] User
Configuration [Auto] EFI/
OS chooses configuration
F9 Setup Defaults
F10 Save and Exit
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
[30]
[40]
[50]
[75]
<Enable>
<3F8>
<IRQ3>
<Enable>
<2F8>
<IRQ4>
<RS232>
<Enable>
<3E8>
<IRQ3>
<Enable>
<2E8>
<IRQ4>
<Disable>
<Disable>
<Always off>
F5/F6 Change Values
Enter Select  SubMenu
Serial Port 1 to Serial Port 4
WDT
Configures the settings of the serial port.
Enable or disable the watchdog function.
Disable Disable this serial port.
Case Open
Enable
Enable or disable the case open function.
Enable this serial port.
Type
F9 Setup Defaults
F10 Save and Exit
AC Power Loss
Choose RS232/RS422/RS485 for the serial port type for COM port 2 only.
Set the AC power loss to Always off or Always on. When set to Always off, the system’s status will
be power-off after an AC power loss event. When set to Always on, the system’s status will be
power-on after an AC power loss event.
41
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PC Health Status
Security
This section displays the PC health status.
This section configures the trusted platform module (TPM) function.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Main
PC Health Status
0.992 V
5.056 V
12.144 V
1.200 V
3.056 V
3.228 V
Temperature
System (oC/oF)
CPU (oC/oF)
34.0 C/ 93.2 F
40.5 C/ 104.9 F
Fan Speed
SYS FAN
CPU FAN
SYS FAN 2
0 RPM
1962 RPM
0 RPM
↑/↓ Select Item
←/→ Select Item
Security
Current TPM Device
TPM State
TPM Availability
TPM Operation
Clear TPM
Supervisor Password
Voltage
VCORE
5V
+12V
VDDQ
VBAT
3VSB
F1 Help
Esc Exit
Advanced
InsydeH20 Setup Utility
Boot
Exit
<TPM 2.0 (DTPM)>
Enabled, Owned
<Available>
<No Operation>
[]
Not installed
Rev. 5.0
Storage Password Setup
Page
Set Supervisor Password
Set All Hdd Password
Set All Master Hdd Password
F5/F6 Change Values
Enter Select  SubMenu
Storage
F9 Setup Defaults
F10 Save and Exit
Password Setup Page
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
TPM Availability
Show or hide the TPM availability and its configurations.
TPM Operation
Enable or disable the TPM function. It displays the following options:
•
No Operation: No changes to the current state.
•
Disable: Disable and deactivate TPM.
•
Enable: Enable and activate TPM.
Clear TPM
Remove all TPM ownership contents.
42
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Set Supervisor Password
Main
Set the supervisor’s password. The length of the password must be greater than
one character and less than or equal to 10 characters.
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Device Name:
[ST3160318AS]
Security Mode:
No Accessed
Rev. 5.0
Set Storage Password
Set Master Hdd Password
Set All Hdd Password
Set the user password for all HDDs. The length of the password must be greater than
one character and less than or equal to 32 characters.
Set All Master Hdd Password
Set the master password for all HDDs. The length of the password must be greater
than one character and less than or equal to 32 characters.
Storage Password Setup Page
Set the storage password for each detected device.
F1 Help
Esc Exit
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Security Mode Description
Lock: HDD security status is enabled and lock.
Unlock: HDD security status is enabled and lock.
Change: HDD security status is unlock and users are allowed to change the password.
Disable: Remove the password from the device.
No Access: HDD Secutiry status is not enabled.
Storage Password Setup
Page
Storage Password Setup
ST3160318AS
↑/↓ Select Item
←/→ Select Item
↑ and ↓ to change option. ENTER to select an option. ESC to exit.
Set Storage Password
Set all HDD password. The length of password must be greater than one character.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Set Master Hdd Password
Set master HDD password. The length of password must be greater than one character and less than or equal to 32 characters.
When the security mode is set to Lock, input the master HDD password to unlock the
HDD.
Clear the HDD password by pressing “Enter” to disable HDD security and set a new
master HDD password.
F9 Setup Defaults
F10 Save and Exit
ST3160318AS (Device Name)
Select this option to set a password for the selected device.
43
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Boot
This section configures boot options.
Main
Advanced
Security
Numlock
Boot Type
PXE Boot to LAN
USB Boot

InsydeH20 Setup Utility
Boot
Exit
<On>
<Legacy Boot Type>
<Disabled>
<Enabled>
InsydeH20 Setup Utility
Boot
Rev. 5.0
Boot Device Priority
Selects Power-on state for
Numlock
Normal Boot Menu

<Normal>
Rev. 5.0
Select Normal Boot Option
Priority or Advance Boot
Option Priority
Boot Type Order
Legacy
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F1 Help
Esc Exit
F9 Setup Defaults
F10 Save and Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Numlock
Normal Boot Menu
Select the power-on state for numlock.
Boot Type
Select the boot type. The options are Dual Boot Type, Legacy Boot Type or UEFI Boot
Type.
Select the boot menu type: normal or advanced.
For the advanced menu type: Use + and - keys to arrange the priority of the
boot devices in the list.
For normal menu type: Select the “Boot Type Order” or “Hard Disk Drive” category to
view and arrange the order of the boot devices in the list.
PXE Boot Capability
Boot Type Order
Enable or disable PXE boot to LAN.
Select the priority of boot type: Normal Boot or Advance Boot.
USB Boot
Enable or disable booting to the USB boot devices.
Note:
If the boot type is set to UEFI, the method for RAID volume creation will be different.
Please refer to Chapter 9 ̵- RAID for more information.
44
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Exit
Updating the BIOS
This section configures the parameters for exiting the BIOS menu.
To update the BIOS, you will need the new BIOS file and a flash utility. Please contact technical support or your sales representative for the files and specific instructions about how to
update BIOS with the flash utility.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing BIOS updating procedure. For your convenience, we
will also provide you with an auto-execution file in the BIOS file downloaded. This auto-execution file will bring you directly to the flash utility menu soon after system boots up and finishes
running the boot files in your boot disk.
Rev. 5.0
Exit system setup and save
your changes.
Exit Saving Changes
Load Optimal Defaults
Discard Changes
RRead file successfully.
(path= “platform.ini”)
Information
Please do not remove the AC power
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2016, Insyde Software Corp. All Rights Reserved.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Initializing
Current BIOS Model name: SD100-H110/Q170
New BIOS Model name: SD100-H110/Q170
Current BIOS version: 65.05A
New BIOS version: 65.05A
F9 Setup Defaults
F10 Save and Exit
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\SD100-H110/Q170>_
100%
100%
Exit Saving Changes
Select this field and then press <Enter> to exit the BIOS setup and save your
changes.
Load Optimal Defaults
Select this field and then press <Enter> to load optimal defaults.
Discard Changes
Select this field and then press <Enter>to exit the BIOS setup without saving your
changes.
45
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Notice: BIOS SPI ROM
1. The Intel® Management Engine has already been integrated into this system board. Due to
the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board
and used on another system board of the same model.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
46
Chapter 7 BIOS Setup
www.dfi.com
Chapter 8
Chapter 8 - Supported Software
For Windows 8.1
The DVD that came with the system board contains drivers, utilities and software applications
required to enhance the performance of the system board.
Insert the DVD into a DVD-ROM drive. The autorun screen (Mainboard Utility DVD) will appear.
If the “Autorun” does not automatically start, please go directly to the root directory of the
DVD and double-click “Setup”.
For Windows 10
47
Chapter 8 Supported Software
www.dfi.com
Chapter 8
For Windows 7
Intel Chipset Software Installation Utility
The Intel Chipset Software Installation Utility is used for updating Windows® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utility, click “Intel Chipset Software Installation Utility” on the main menu.
1. Setup is ready to install the
utility. Click Next.
2. Read the license agreement
then click Yes.
48
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Graphics Drivers
3. Go through the readme
document for more installation tips then click Next.
To install the driver, click “Intel Graphics Drivers” on the main menu.
1. Setup is now ready to
install the graphics driver.
Click Next.
4. Click Finish to exit setup.
By default, the “Automatically run WinSAT and enable the Windows Aero
desktop theme” is enabled. With this enabled, after installing the graphics
driver and the system rebooted, the screen will turn blank for 1 to 2 minutes
(while WinSAT is running) before the Windows 7/Windows 8.1/Windows 10
desktop appears. The “blank screen” period is the time Windows is testing
the graphics performance.
2. Read the license agreement
then click Yes.
49
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Audio Drivers
3. Go through the readme
document for system requirements and installation
tips then click Next.
To install the driver, click “Audio Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
4. Setup is now installing the
driver. Click Next to continue.
2. Click “Yes, I want to restart
my computer now” then
click Finish.
Restarting the system will
allow the new software
installation to take effect.
5. Click “Yes, I want to restart
this computer now” then
click Finish.
Restarting the system will
allow the new software
installation to take effect.
50
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel LAN Drivers
4. Click Install to begin the
installation.
To install the driver, click “Intel LAN Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
5. After completing installation, click Finish.
2. Click “I accept the terms
in the license agreement”
then click “Next”.
3. Select the program featuers
you want installed then
click Next.
51
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Kernel Mode Driver (For Windows 7 only)
3. Click “Restart Now“ to
restart your computer when
the installation is complete.
To install the driver, click “Kernel Mode Driver” on the main menu.
1. Click “Yes“ to install the
update.
2. The update is installed
now.
52
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Management Engine Drivers
3. Setup is currently installing
the driver. After installation
has completed, click Next.
To install the driver, click “Intel Management Engine Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
4. Please wait while the product is being installed.
2. Read the license agreement
then click Next.
5. After completing installation, click Finish.
53
Chapter 8 Supported Software
www.dfi.com
Chapter 8
HW Utility
3. Read the license agreement
then click “I accept the terms
in the license agreement”.
Click “Next”.
HW Utility provides information about the board, Watchdog,and DIO. To access the utility, click
“HW Utility” on the main menu.
Note:
If you are using Windows 7 or later versions, you need to access the operating system
as an administrator to be able to install the utility.
1. Setup is ready to install the
driver.
4. The wizard is ready to begin
installation. Click “Install”.
2. Click “Next” to continue.
5. Please wait while the program
features are being installed.
54
Chapter 8 Supported Software
www.dfi.com
Chapter 8
6. After completing installation, click
“Finish”.
The HW Utility icon will appear on the desktop. Double-click the icon to open the utility.
Information
HW Health
55
Chapter 8 Supported Software
www.dfi.com
Chapter 8
DIO
HW Health Set
Backlight
WatchDog
56
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel USB 3.0 Drivers (For Windows 7 and Windows 8.1)
3. Go through the readme document for more installation tips
then click Next.
To install the driver, click “Intel USB 3.0 Driver” on the main menu.
1. Setup is ready to install the driver.
Click Next.
4. Setup is currently installing the
driver. After installation has completed, click Next.
2. Read the license agreement then
click Yes.
5. After completing installation, click
Finish.
57
Chapter 8 Supported Software
www.dfi.com
Chapter 8
IO Driver
3. Read the file information then click
Next.
To install the driver, click “Intel Serial IO Driver” on the main menu
1. Setup is ready to install the driver.
Click Next.
4. Setup is ready to install the driver.
Click Next.
2. Read the license agreement carefully.
Click “I accept the terms in the License Agreement” then click Next.
58
Chapter 8 Supported Software
www.dfi.com
Chapter 8
5. Setup is now installing the
driver.
Microsoft Framework 4.5.2 (For Windows 7)
Note:
Before installing Microsoft Framework 4.5.2, make sure you have updated your
Windows 7 operating system to Service Pack 3.
To install the driver, click “Microsoft Framework 4.5.2” on the main menu.
1. Setup is now extracting files.
6. Click Finish.
2. Read the license agreement carefully.
Click “I have read and accept
the terms of the License Agree
ment” then click Install.
59
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel® Rapid Storage Technology
3. Setup is now installing the driver.
The Intel® Rapid Storage Technology is a utility that allows you to monitor the current status
of the SATA drives. It enables enhanced performance and power management for the storage
subsystem.
To install the driver, click “Intel Rapid Storage Technology” on the main menu. Please refer to
Chapter 9 for more information.
4. Click Finish.
60
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Infineon TPM 1.2 Driver and Tool (optional)
4. Enter the necessary information
and then click Next.
To install the driver, click “Infineon TPM driver and tool (option)” on the main menu.
1. The setup program is preparing
to install the driver.
5. Select a setup type and then click
Next.
2. The setup program is now ready
to install the utility. Click Next.
6. Click Install.
3. Click “I accept the terms in the
license agreement” and then
click “Next”.
61
Chapter 8 Supported Software
www.dfi.com
Chapter 8
7. TPM requires installing the Microsoft Visual C++ package prior to
installing the utility. Click Install.
10. Click “Yes“ to restart your system.
8. The setup program is currently
installing the Microsoft Visual
C++ package.
9. Click Finish.
62
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Adobe Acrobat Reader 9.3
To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.
1. Click Next to install or click
Change Destination Folder
to select another folder.
2. Click Install to begin installation.
3. Click Finish to exit installation.
63
Chapter 8 Supported Software
www.dfi.com
Chapter 9
Chapter 9 - RAID (Only for Intel® Q170 Chipset)
Settings
The system board allows configuring RAID on Serial ATA drives. It supports RAID 0 and RAID 1.
To enable the RAID function, the following settings are required.
RAID Levels
1. Connect the Serial ATA drives.
RAID 0 (Striped Disk Array without Fault Tolerance)
2. Enable RAID in the BIOS.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk
drives. This improves the I/O performance of the drives at different channel; however it is not
fault tolerant. A failed disk will result in data loss in the disk array.
3. Create a RAID volume.
4. Install the Intel Rapid Storage Technology Utility.
Step 1: Connect the Serial ATA Drives
RAID 1 (Mirroring Disk Array with Fault Tolerance)
Refer to chapter 2 for details on connecting the Serial ATA drives.
RAID 1 copies and maintains an identical image of the data from one drive to the other drive.
If a drive fails to function, the disk array management software directs all applications to the
other drive since it contains a complete copy of the drive’s data. This enhances data protection
and increases fault tolerance to the entire system. Use two new drives or an existing drive and
a new drive but the size of the new drive must be the same or larger than the existing drive.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID Configuration Utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
Step 2: Enable RAID in the BIOS
1. Power-on the system then press <Del> to enter the main menu of the BIOS utility.
2. Go to “Advanced” menu, and select the “SATA Configuration” menu.
3. Change the “SATA Mode Selection” to “RAID” mode.
4. Save the changes in the “Save & Exit” menu.
5. Reboot the system.
64
Chapter 9 RAID
www.dfi.com
Chapter 9
Step 3: Create a RAID Volume
Step 3-1: Create a RAID Volume if the boot type is UEFI
1. When the Intel RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
If the boot type is set to UEFI, RAID volume creation will be different. Please use the following
steps to create RAID volumes. To set the boot type, enter the Insyde BIOS and go to “Boot”
>”Boot type”.
®
2. Select 1: Create RAID Volume and press <Enter>.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
1. Go to the “Advanced” menu of the Insyde BIOS.
4. Use the up or down arrow keys to select the strip size and press <Enter>.
2. The “Intel® Rapid Storage Technology” menu appears. Enter this menu.
5. Press <Enter> to select the physical disks.
6. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
Main
7. Press <Enter>.
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
ACPI Configuration Setting
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
MEBX Configuration
 Active Management Technology Support
 SIO NUVOTON6106D
 Intel Rapid Storage Technology








8. Select the volume size and press <Enter>. You must select less than one hundred percent
of the available volume space to leave space for the second volume.
9. Press <Enter> to create the volume.
10. At the prompt, press <Y> to confirm volume creation.
11. Select 4: Exit and press <Enter>.
12. Press <Y> to confirm exit.
F1 Help
Esc Exit
Note:
These steps are cited from the Intel® Suppot site, “Set Up a System with Intel®
Matrix RAID Technology” (Article ID: 000005789).
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
3. The screen displays all available drives. Select “Create RAID volume” to create a RAID
volume”.
4. Use the up or down arrow keys to select the RAID level and press <Enter>.
5. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
6. Press <Enter>.
7. Use the up or down arrow keys to select the strip size and press <Enter>.
8. Enter the volume size and press <Enter>.
9. At the prompt, press <Y> to confirm volume creation.
65
Chapter 9 RAID
www.dfi.com
Chapter 9
Step 4: Install the Intel Rapid Storage Technology Utility
5. Go through the readme
document to view system
requirements and installation information then click
Next.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/
or SATA drives. It enables enhanced performance and power management for the storage
subsystem.
1. Insert the provided DVD into an optical drive.
2. Click “Intel Rapid Storage Technology Utility” on the main menu.
3. Setup is ready to install
the utility. Click Next.
6. Click Next to install to
the default folder or click
change to choose another
destination folder.
4. Read the license agreement and click “I accept
the terms in the License
Agreement.“ Then, click
Next.
7. Confirm the installation and
click Next.
66
Chapter 9 RAID
www.dfi.com
Chapter 9
8. Click “Yes, I want to restart
this computer now” to
complete the installation
and then click Finish.
67
Chapter 9 RAID
www.dfi.com
Chapter 10
Chapter 10 - Intel AMT Settings (Only for Intel® Q170 Chipset)
Enable Intel® AMT in the BIOS
Overview
1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.
Intel Active Management Technology (Intel® AMT) combines hardware and software solution to
provide maximum system defense and protection to networked systems.
2.
In the Advanced menu, select Avtive Management Technology Support.
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
Main
• Discover
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
AMT Configuration
ACPI Configuration
CPU Configuration
Video Configuration
Audio Configuration
SATA Configuration
USB Configuration
PCI Express Configuration
ME Configuration
MEBX Configuration
 Active Management Technology Support
 SIO NUVOTON6106D








Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
• Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
F1 Help
Esc Exit
3.
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
F9 Setup Defaults
F10 Save and Exit
Select Enabled for the Intel AMT Support option.
InsydeH20 Setup Utility
Rev. 5.0
Advanced
Active Management Technology Support
Intel AMT Support
Un-Configure ME
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
<Enabled>
<Disabled>
F5/F6 Change Values
Enter Select  SubMenu
Enable/Disable Intel(R)
Active
Management Technology
BIOS Extension.
Note : iAMT H/W is always enabled. This Option
Just controls the BIOS extension execution
F9 Setup Defaults
F10 Save and Exit
68
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
4.
Set up Intel® AMT using the Intel® Management
Engine BIOS Extension (MEBX)
In the Exit menu, select Exit Saving Changes then select OK.
Main
Advanced
Security
InsydeH20 Setup Utility
Boot
Exit
Rev. 5.0
1. After the system reboots, press <Del> to enter the BIOS menu again.
Exit system setup and save
your changes.
Exit Saving Changes
Load Optimal Defaults
Discard Changes
2. In the Advanced menu, select MEBX Configuration to enter the Manageability Engine
BIOS Extension (MEBx) Setup.
3. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password,
then press “Enter”.
F1 Help
Esc Exit
↑/↓ Select Item
←/→ Select Item
F5/F6 Change Values
Enter Select  SubMenu
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
F9 Setup Defaults
F10 Save and Exit
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
.
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
69
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
4. Enter a password in the space provided under Intel(R) ME Password then press Enter. The
password must include:
•
•
•
•
•
5. You will be asked to verify the password. Enter the same new password in the space provided under Verify Password then press Enter.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
Intel(R) ME Password
6. Select Intel(R) ME General Settings then press Enter.
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
70
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
7. Select Change Intel(R) ME Password then press Enter.
8.Select Local FW Update then press Enter. Select Enabled or Disabled or password
Protected then press Enter.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under Intel(R) ME New Password then press Enter.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
Disabled
Enabled
Password Protected
<Enabled>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9. Select Previous Menu until you return to the Main Menu. Select Intel(R) AMT Configuration then press Enter.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
[Esc]= Exit
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[↑↓] = Move Highlight
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
71
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
10.In the Intel(R) AMT Configuration menu, select Manageability Feature Selection
then press Enter. Select Enabled or Disabled then press Enter.
12. In the SOL/Storage Redirection/KVM menu, select Username and Password then
press Enter. Select Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved..
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
11.In the Intel(R) AMT Configuration menu, select SOL/Storage Redirection/KVM
then press Enter.
13. In the SOL/Storage Redirection/KVM menu, select SOL then press Enter. Select
Enabled or Disabled then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and Password
SOL
Storage Redirection
KVM Feature Selection
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
Menu for FW Redirection Configuration
[↑↓] = Move Highlight
< Enabled>
<Enabled>
<Enabled>
<Enabled>
[Esc]= Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
72
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
14. In the SOL/Storage Redirection/KVM menu, select Storage Redirection then press
Enter. Select Enabled or Disabled then press Enter.
16. Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select
User Consent then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
User Opt-in
Opt-in Configurable from Remote IT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< KVM>
< Enabled>
Disabled
Enabled
Configure When User Consent Should be Required.
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
15. In the SOL/IDER/KVM menu, select KVM Feature Selection then press Enter. Select
Enabled or Disabled then press Enter.
[Esc]= Exit
17. In the User Consent menu, select User Opt-in then press Enter. Select None or KVM
or ALL then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
73
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
18. In the User Consent menu, select Opt-in Configurable from Remote IT then press
Enter. Select Enabled or Disable Remote Control of KVM Opt-in Policy then press
Enter.
20. In the Intel(R) AMT Configuration menu, select Network Setup then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< KVM>
< Enabled>
Disabled
Enabled
[↑↓] = Move Highlight
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
< Enabled>
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
21. In the Intel(R) ME Network Setup menu, select Intel(R) ME Network Name Settings then press Enter.
19. Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select
Password Policy then press Enter.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Intel (R) ME Network Name Settings
> TCP/ IP Settings
Manageability Feature Selection
< Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Step And Configuration
Anytime
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
74
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
22. In the Intel(R) ME Network Name Settings menu, select Host Name then press
Enter. Enter the computer’s host name then press Enter.
24. Select Shared/Dedicated FQDN then press Enter. Select Shared or Dedicated then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Host Name
[Enter] = Complete Entry
Dedicated
Shared
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc]= Discard Changes
23. Select Domain Name then press Enter. Enter the computer’s domain name then press
Enter.
25. Select Dynamic DNS Update then press Enter. Select Enabled or Disabled then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Computer Domain Name
[Enter] = Complete Entry
_
_
<Shared>
<Disabled>
_
_
<Shared>
<Disabled>
Disabled
Enabled
[Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
75
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
28. In the Intel(R) AMT Configuration menu, select Activate Network Access then
select Y/N and press Enter.
26. Select Previous Menu until you return to the Intel(R) ME Network Setup menu. Select
TCP/IP Settings then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
TCP/ IP SETTINGS
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
> Wired LAN IPV4 Configuration
[↑↓] = Move Highlight
[Enter] = Select Entry
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
[Esc]= Exit
<Anytime>
<Full Unprovision>
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
27. In the TCP/IP Settings menu, select Wired LAN IPV4 Configuration then press
Enter.
29. In the Intel(R) AMT Configuration menu, select Unconfigure Network Access then
press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
< Enabled>
<Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
< Enabled>
<Anytime>
<Full Unprovision>
Full Unprovision
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
76
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
30. In the Intel(R) AMT Configuration menu, select Remote Setup And Configuration
then press Enter.
32. In the Intel(R) Remote Setup And Configuration menu, select Provisioning Record then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
< Enabled>
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
<Anytime>
<Full Unprovision>
_
_
Provision Record is not present
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
31. In the Intel(R) Remote Setup And Configuration menu, select Current Provisioing
Mode then press Enter.
[Esc]= Exit
33. In the Intel(R) Remote Setup And Configuration menu, select Provisioning server
IPV4/IPV6, enter the Provisioning server address then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
Provisioning Mode:PKI
_
_
Provisioning server address
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
77
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
34. In the Intel(R) Remote Setup And Configuration menu, select Provisioning server
FQDN, enter the FQDN of Provisioning server then press Enter.
36. In the Intel(R) Remote Setup And Configuration menu, select TLS PKI then press
Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
37. In the Intel(R) Remote Configuration menu, select Remote Configuration**
then press Enter, select Enabled or Disabled then press Enter.
35. In the Intel(R) Remote Setup And Configuration menu, select RCFG then press
Enter, and select Start Configuration Y/N then press enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL (R) REMOTE CONFIGURATION
Start Configuration
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
< Enabled>
_
Disabled
Enabled
[ESC] = Exit
[ESC] = Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[↑↓] = Move Highlight
[Esc]= Exit
[Enter] = Select Entry
[Esc]= Exit
78
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
38. Select PKI DNS Suffix, Enter the PKI DNS Suffix then press Enter.
40. In the Intel(R) AMT Configuration menu, select Power Control then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
_
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[↑↓] = Move Highlight
[Esc]= Exit
<Anytime>
<Full Unprovision>
[Enter] = Select Entry
[Esc]= Exit
41. In the Intel(R) AMT Power Control menu, select Intel(R) AMT ON in Host Sleep
States then press Enter. Select an option then press Enter.
39. Select Manage Hashes then press Enter, and select one of hash name.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
These configurations are effective only after AMT provisioning has started
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
< Enabled>
Intel (R) AMT ON in Host Sleep States
< Enabled>
_
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Mobile: ON in S0
Mobile: ON in S0, ME Wake in S3, S4-5 (AC only)
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
79
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
42. In the Intel(R) AMT Power Control menu, select Idle Timeout then press Enter.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
<ENTER> = Complete Entry
[ESC]= Discard Changes
43. Select Previous Menu until you return to the Main Menu. Select Exit then press Enter.
Type Y then press Enter.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1180
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
80
Chapter 10 Intel AMT Settings
www.dfi.com
Appendix A
Appendix A - Troubleshooting Checklist
The picture seems to be constantly moving.
Troubleshooting Checklist
1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.
This chapter of the manual is designed to help you with problems that you may encounter
with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple
causes.
2. Move away any objects, such as another monitor or fan, that may be creating a magnetic
field around the display.
Some of the most common things to check when you encounter problems while using your
system are listed below.
The screen seems to be constantly wavering.
3. Make sure your video card’s output frequencies are supported by this monitor.
1. The power switch of each peripheral device is turned on.
1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off.
Fluorescent lights adjacent to the monitor may also cause screen wavering.
2. All cables and power cords are tightly connected.
Power Supply
3. The electrical outlet to which your peripheral devices are connected is working. Test the
outlet by plugging in a lamp or other electrical device.
When the computer is turned on, nothing happens.
4. The monitor is turned on.
1. Check that one end of the AC power cord is plugged into a live outlet and the other end
properly plugged into the back of the system.
5. The display’s brightness and contrast controls are adjusted properly.
2. Make sure that the voltage selection switch on the back panel is set for the correct type of
voltage you are using.
6. All add-in boards in the expansion slots are seated securely.
3. The power cord may have a “short” or “open”. Inspect the cord and install a new one if
necessary.
7. Any add-in board you have installed is designed for your system and is set up correctly.
Monitor/Display
Floppy Drive
If the display screen remains dark after the system is turned on:
The computer cannot access the floppy drive.
1. Make sure that the monitor’s power switch is on.
1. The floppy diskette may not be formatted. Format the diskette and try again.
2. Check that one end of the monitor’s power cord is properly attached to the monitor and
the other end is plugged into a working AC outlet. If necessary, try another outlet.
2. The diskette may be write-protected. Use a diskette that is not write-protected.
3. Check that the video input cable is properly attached to the monitor and the system’s display adapter.
3. You may be writing to the wrong drive. Check the path statement to make sure you are
writing to the targeted drive.
4. Adjust the brightness of the display by turning the monitor’s brightness control knob.
4. There is not enough space left on the diskette. Use another diskette with adequate storage
space.
81
Appendix A Troubleshooting Checklist
www.dfi.com
Appendix A
Hard Drive
System Board
Hard disk failure.
1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is
loose, power off the system, re-install the card and power up the system.
1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS.
2. Check the jumper settings to ensure that the jumpers are properly set.
2. If the system is configured with two hard drives, make sure the bootable (first) hard drive
is configured as Master and the second hard drive is configured as Slave. The master hard
drive must have an active/bootable partition.
3. Verify that all memory modules are seated securely into the memory sockets.
4. Make sure the memory modules are in the correct locations.
Excessively long formatting period.
5. If the board fails to function, place the board on a flat surface and seat all socketed components. Gently press each component into the socket.
If your hard drive takes an excessively long period of time to format, it is likely a cable connection problem. However, if your hard drive has a large capacity, it will take a longer time to
format.
6. If you made changes to the BIOS settings, re-enter setup and load the BIOS defaults.
Serial Port
The serial device (modem, printer) doesn’t output anything or is outputting garbled
characters.
1. Make sure that the serial device’s power is turned on and that the device is on-line.
2. Verify that the device is plugged into the correct serial port on the rear of the computer.
3. Verify that the attached serial device works by attaching it to a serial port that is working
and configured correctly. If the serial device does not work, either the cable or the serial
device has a problem. If the serial device works, the problem may be due to the onboard
I/O or the address setting.
4. Make sure the COM settings and I/O address are configured correctly.
Keyboard
Nothing happens when a key on the keyboard was pressed.
1. Make sure the keyboard is properly connected.
2. Make sure there are no objects resting on the keyboard and that no keys are pressed during the booting process.
82
Appendix A Troubleshooting Checklist
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising