DFI | COM332-B(R.B1) | manual | Dfi COM332-B(R.B1) Manual

Dfi COM332-B(R.B1) Manual
COM332-B(R.B1)
COM Express Carrier Board
User’s Manual
A50600835
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2018. All Rights Reserved.
Trademarks
Notice:
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
DP Ports..................................................................................................... 15
RJ45 LAN Port ............................................................................................ 16
USB Ports ................................................................................................... 16
Audio ......................................................................................................... 17
I/O Connectors ........................................................................................... 18
Copyright........................................................................................................... ..2
S/PDIF Connector ....................................................................................... 18
Digital I/O Connector .................................................................................. 18
LVDS LCD Panel Connector ......................................................................... 19
LCD/Inverter Power Connector .................................................................... 19
eDP Connector ........................................................................................... 20
LPC Female Header .................................................................................... 21
SATA (Serial ATA) Connectors ...................................................................... 22
Cooling Fan Connector ................................................................................ 22
I2C Connector ............................................................................................. 23
SMBus Connector ....................................................................................... 23
Power Connectors ....................................................................................... 24
VGA Connector ........................................................................................... 24
Front Panel Connector ................................................................................ 25
Standby Power LED .................................................................................... 26
Battery ....................................................................................................... 26
Expansion Slots .......................................................................................... 27
COM Express Connectors ............................................................................ 28
SDIO.......................................................................................................... 30
Serial Interface Connectors ......................................................................... 30
Switches .................................................................................................... 31
LAN Link LED ............................................................................................. 31
Thermal Trip LED........................................................................................ 32
WatchDog Output LED ................................................................................ 32
Trademarks ........................................................................................................ 2
FCC and DOC Statement on Class B ..................................................... 2
Warranty.............................................................................................................. 4
Static Electricity Precautions...................................................................... 4
Safety Measures .............................................................................................. 4
About the Package ......................................................................................... 5
Optional Items.................................................................................................. 5
Before Using the System Board............................................................... 5
Chapter 1 - Introduction ............................................................................. 6
Specifications ................................................................................................ 6
Chapter 3 - Supported Software ........................................................... 33
Chapter 2 - Hardware Installation................................................ 7
Board Layout ................................................................................................. 7
Block Diagram ............................................................................................... 7
Mechanical Diagram .................................................................................... 8
Jumper Settings ........................................................................................... 9
USB Power Select ......................................................................................... 9
Panel Power Select ....................................................................................... 9
Clear CMOS ................................................................................................ 10
Backlight Power Select ................................................................................ 10
VCC5_IN Power Select ................................................................................ 11
BIOS Select ................................................................................................ 11
ATX/AT Mode Select ................................................................................... 12
LVDS/eDP Signal Select............................................................................... 12
LCD/Inverter Power Select .......................................................................... 13
Dimming Mode Select ................................................................................. 13
PEG Lane Reversed..................................................................................... 14
Function Test Jumper ............................................................................... 14
Battery Low Indicator ................................................................................. 14
Rear Panel I/O Ports ................................................................................. 15
3
Chapter 1 Introduction
www.dfi.com
Warranty
Static Electricity Precautions
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
•
•
•
One COM332-B(R.B1) board
One Serial ATA data cable (Length: 500mm)
One VGA cable
Optional Items
•
•
•
•
Serial ATA data cable (Length: 500mm)
LPC EXT-RS232 module (4 x RS232 ports)
LPC EXT-RS485 module (4 x RS485 ports)
I/O shield
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
•
•
Memory module
Storage devices such as hard disk drive, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Specifications
GRAPHICS
Display
EXPANSION
Interface
AUDIO
REAR I/O
Audio Codec
Ethernet
USB
Display
Audio
INTERNAL I/O
Serial
Display
Audio
POWER
SATA
DIO
LPC
SMBus
Type
Connector
RTC Battery
ENVIRONMENT
1 x VGA
1 x LVDS/eDP (eDP available upon request)
3 x DP
1 x eDP/LVDS (LVDS available upon request)
1 x PCIe x16
4 x PCIe x1
1 x M.2 M Key 2280
1 x SDIO
Realtek ALC888S-VD2-GR
Temperature
Humidity
MTBF
MECHANICAL
1 x GbE (RJ-45)
4 x USB 3.1 (Gen 2)
4 x USB 2.0
3 x DP
1 x Line-in
1 x Line-out
1 x Mic-in
2 x Serial Interface Connectors (TX/RX)
1 x VGA (2.54mm)
1 x LVDS LCD Panel Connector
1 x LCD/Inverter Power
1 x eDP LCD Panel Connector
1 x Audio (Line-out/Mic-in)
1 x S/PDIF
4 x SATA 3.0 (up to 6Gb/s)
1 x 8-bit DIO
1 x LPC
1 x SMBus
12V, 5VSB, VCC_RTC (ATX mode)
12V, VCC_RTC (AT mode)
4-pin ATX 12V power
24-pin ATX power
CR2032 Coin Cell
Dimensions
Compliance
Operating: 0 to 60°C
Storage: -40 to 85°C
Operating: 5 to 90% RH
Storage: 5 to 90% RH
488,117 hrs @ 25°C; 253,684 hrs @ 45°C; 136,621 hrs @ 60°C
Calculation Model: Telcordia Issue 2, Method Case 3
Environment: GB, GC – Ground Benign, Controlled
microATX Form Factor
244mm (9.6") x 244mm (9.6")
PICMG COM Express® R2.1, Type 6
Basic, Compact Modules
6
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Hardware Installation
Block Diagram
Board Layout
BIOS Select (JP4)
DP 1
LC4064ZE
15
PEG LANE Reversed (JP8)
SPI Function (JP5)
VGA
2
1
13 LPC
1
14
2
USB 4-5/6-7 Power
Select (JP3)
USB 2.0
USB 4-5
DP 2
Battery
2
6
2
I C
2
1
5
1
Basic
Compact
SATA 3.0
2
6
1
5
SATA 0
USB 1-2 USB 3.1 Gen2
1
Serial Interface 0
(Rx/Tx)
SATA 1
USB 3-4 Power
Select (JP1)
1
1
LCD/Inverter
Power Select
(JP11) 2
D110
D1
SATA 2
COM Express Connector
C1
B1
C110
B110
13
1
1
1
1
6
5
2
1
COM Express Connector
DIO
Line-in
Line-out
Mic-in
LAN Link LED
A1
1
1
Battery Low
Indicator
Thermal Trip LED
LVDS/eDP Signal
Select (JP9)
40
39
Connector
Row C/D
HD Audio
SPI
LVDS/eDP
+12V
Power
Panel Power
Select (JP10)
2
M.2
Mkey 2280
PCIe
eDP
Switch IC
LVDS
LVDS
eDP
LVDS
1
11
1
GPIO
TYPE 6
DDI
VGA
Connector
Row A/B
PCIe
LCD/Inverter
Power
LVDS LCD Panel
USB 2.0
4x
PCIe x16 1x
USB 3.1
12
24
1
A110
USB 2.0
SDIO
ATX
Power
1
SATA 3
USB 3.1
4x
DP 3x
Serial Port 2x
1
GLAN
USB 2.0
PCIe x1 4x
1
Backlight
Power Select
(JP13)
Dimming Mode
Select (JP14)
Serial Interface 1
(Rx/Tx) 1
1
LAN
USB 3-4
USB 3.1 Gen2
ATX/AT Mode
Select (JP15)
VCC5_IN Power
Select (JP12)
1
TYPE 6
I 2C
Standby
Power LED
ATX/AT Mode
Select (JP16)1
Buzzer
1
SMBus
19 Digital I/O
1
Type 6 LED
USB 1-2 Power
Select (JP2)
USB 2.0
USB 6-7
DP 3
LPC
Clear CMOS (JP6)
Debug LED
1
MDI
SATA 3.0 4x
1
SDIO
1
LED4
LED5
LED6
LED7
LED8
LED9
LED10
16
System Fan
1
1
12
Front
WatchDog Panel
Output
LED
PCIe 1 (PCIe x16)
SPI Flash BIOS
1
Realtek
ALC888
S/PDIF
Front
Audio
Power
M.2
1
1
2
40
eDP
PCIe 2 (PCIe x1)
9
10
PCIe 3 (PCIe x1)
Reset
PCIe 5 (PCIe x1)
Sleep
Lid
PCIe 4 (PCIe x1)
2
1 5
SMBus
7
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Mechanical Diagram
243.84
237.49
225.84
197.18
188.34
164.84
155.41
141.34
138.01
124.84
120.61
110.18
103.21
102.84
80.01
61.26
40.94
34.29
20.62
0.00
0.00
7.31
10.16
0.00
3.16
10.50
16.74
33.02
48.73
57.10
68.75
138.95
144.75
155.75
165.10
185.75
186.74
237.49
124.18
112.18
80.01
51.25
13.97
0.00
8
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Panel Power Select
Jumper Settings
USB Power Select
1 2 3
1-2 On: +5V
USB 2.0
4-5/6-7 (JP3)
1 2 3
USB 3.1 Gen2
2-3 On:
1-2 (JP2)
+5VDU (default)
USB 3.1 Gen2
3-4 (JP1)
3
2
1
1
1
1-2 On: +5V
3
2
1
2-3 On:
+5VDU (default)
JP10
JP3 (for USB 2.0 4-5/6-7), JP2 (for USB 3.1 Gen2 1-2), and JP1 (for USB 3.1 Gen2 3-4) are
used to select the power of USB ports. Selecting +5VDU will allow you to use a USB keyboard
to wake up the system.
6
4
2
5
3
1
1-2 On: +12V
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
6
4
2
5
3
1
3-4 On: +5V
6
4
2
5
3
1
5-6 On: +3.3V
(default)
The JP10 is used to select the power supplied to the LCD panel.
Important:
Before powering-on the system, make sure JP10’s setting matches the LCD panel’s
specification. Selecting the incorrect voltage will seriously damage the LCD panel.
9
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Clear CMOS
Backlight Power Select
JP6
1 2 3
1-2 On: Normal
(default)
JP13
1 2 3
3
2
1
1-2 On: +3.3V
(default)
2-3 On:
Clear CMOS
1
1
3
2
1
2-3 On: +5V
If you encounter the following situations,
The JP13 is used to select the power level of backlight brightness control.
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
Important:
Before powering-on the system, make sure that the power settings of JP13 match the
power specification of backlight control. Selecting the incorrect voltage will seriously
damage the backlight.
you can reconfigure the system with the default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below:
1. Power-off the system and unplug the power cord.
2. Set JP6 pins 2 and 3 to On. Wait for a few seconds and set JP6 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
10
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
VCC5_IN Power Select
BIOS Select
JP5
2 4 6
JP4
JP12
1 3 5
1-2 On:
+5V_standby
(default)
1 2 3
1 2 3
JP4 1-2 On, JP5 2-3 On:
Boot from Carrier Board SPI BIOS
2 4 6
1 2 3
1 2 3
1
1 3 5
1
3-4 On: +5V
JP4 2-3 On, JP5 2-3 On:
Boot from Module SPI BIOS (default)
1 2 3
2 4 6
1 2 3
JP4 1-2 On, JP5 1-2 On:
Module SPI
1 3 5
5-6 On: NC
1 2 3
1 2 3
JP4 2-3 On, JP5 1-2 On:
Carrier LPC_FWH
The JP12 is used to select the power of the COM Express connector.
JP4 and JP5 are used to determine the BIOS boot device.
11
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
ATX/AT Mode Select
LVDS/eDP Signal Select
JP15
3
2
1
1 2 3
1-2 On: ATX
(default)
1-2 On: eDP
(default)
3
2
1
1
1
JP16
JP9
2-3 On: AT
1 2 3
2-3 On: LVDS
The JP15 allows you to select the ATX or AT power supply mode (Power_OK state).
The JP9 is used to select the display connector type: Embedded DisplayPort (eDP) or LVDS.
The JP16 allows you to select the ATX or AT power supply mode (STR - Suspend to RAM
state).
Note:
JP15 and JP16 need to be set simultaneously.
12
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Dimming Mode Select
LCD/Inverter Power Select
3
2
1
3
2
1
JP14
3
2
1
1
JP11
1-2 On:
+12V (default)
1-2 On: PWM Mode
(default)
3
2
1
2-3 On: Voltage Mode
1
2-3 On: +5V
The JP11 is used to select the power level of LCD inverter connector.
The JP14 allows you to select the mode for the lightness control of the LVDS panel.
Important:
You need to refer to your panel’s user guide to determine the type of mode (PWM or
Voltage) most appropriate for your panel.
13
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
PEG Lane Reversed
Function Test Jumper
Battery Low Indicator
JP8
1 2 3
1-2 On: Normal
(default)
1 2 3
1 2
2-3 On: Lane
Numbers Reversed
1-2 On:
Battery low test
J4
1
1
1 2
1-2 Off: Normal
(default)
The JP8 is used to activate or deactivate the lane reversal mode for the PEG port.
This jumper is used to simulate the signal status that indicates the external battery is low. By
setting J4 pins 1 and 2 to On, it sends a battery low signal to the module.
14
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Rear Panel I/O Ports
USB 2.0
4-5
DP Ports
USB 2.0
6-7
LAN
USB 3.1
Gen2 1-2
Line-in
DP 1
Line-out
Mic-in
DP 1
DP 2
DP 3
USB 3.1
Gen2 3-4
DP 2
DP 3
The rear panel I/O ports consist of the following:
1
•
•
•
•
•
•
•
3
4
4
1
1
1
1
DP ports
USB 2.0 ports
USB 3.1 Gen2 ports
LAN port
Line-in/Surround jack
Line-out jack
Mic-in/Center+Subwoofer jack
DisplayPort (DP) is a digital display interface used to connect a display device such as a computer monitor. It is used to transmit audio and video simultaneously. The interface, which is
developed by VESA, delivers higher performance features than any other digital interface.
15
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
RJ45 LAN Port
USB Ports
USB 2.0
USB 4-5 USB 6-7
LAN
1
1
USB 1-2 USB 3-4
USB 3.1 Gen2
USB allows data exchange between your computer and a wide range of simultaneously accessible external plug-and-play peripherals.
The onboard RJ45 LAN port allows the system board to connect to a local area network by
means of a network hub.
The system board is equipped with four onboard USB 3.1/2.0/1.1 ports (USB 1-2/3-4) and four
onboard USB 2.0/1.1 ports (USB 4-5/6-7).
Driver Installation
You may need to install the proper drivers in your operating system to use the USB device.
Refer to your operating system’s manual or documentation for more information.
16
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Audio
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function:
Line-in
• Jumper Setting
Line-out
JP3 (for USB 2.0 4-5/6-7), JP2 (for USB 3.1 Gen2 1-2), and JP1 (for USB 3.1 Gen2 3-4) must
be set to “2-3 On: +5VDU”. Refer to “USB Power Select” in this chapter for more information.
Mic-in
Line2-JD
A_GND
NC
Mic2-JD
Rear Audio
1
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
10
9
Front Audio
Mic2-L
Mic2-R
Line2-R
A_GND
Line2-L
2
1
Rear Audio
The system board is equipped with three audio jacks. A jack is a one-hole connecting interface
for inserting a plug.
• Line-in/Surround Jack (Light Blue)
This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/FM
radio tuner, synthesizer, etc.
• Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
• Mic-in/Center+Subwoofer (Pink)
This jack is used to connect to the center and subwoofer speakers of the audio system.
Front Audio
The front audio connector allows you to connect to the second line-out and mic-in jacks that
are at the front panel of your system.
BIOS Setting
Refer to the module’s BIOS for more information.
Driver Installation
Install the audio driver. Refer to chapter 3 for more information.
17
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Digital I/O Connector
I/O Connectors
S/PDIF Connector
DIO
2
1
SPDIF in
Ground
SPDIF out
1
+5V
5
1
1
19
S/PDIF
The 8-bit Digital I/O connector (4-bit GPI and 4-bit GPO) provides powering-on and control
functions to the connected external devices. The pin functions of this connector are listed as
the followings:
The S/PDIF connector is used to connect external S/PDIF ports. Your S/PDIF ports may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis then connect the audio cable to the S/PDIF connector. Make sure pin 1
of the audio cable is aligned with pin 1 of the connector.
Pin
Pin Assignment
Pin
Pin Assignment
1
GND
2
+12V
3
DIO7 (GPO3)
4
+12V
5
DIO6 (GPO2)
6
GND
7
DIO5 (GPO1)
8
+5V
9
DIO4 (GPO0)
10
+5V
11
DIO3 (GPI3)
12
GND
13
DIO2 (GPI2)
14
+5V_Standby
15
DIO1 (GPI1)
16
+5V_Standby
17
DIO0 (GPI0)
18
GND
19
GND
18
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LVDS LCD Panel Connector
LVDS LCD Panel Connector
LCD/Inverter Power Connector
Pin
LCD/Inverter Power
8
1
1
2
1
LVDS LCD Panel
40
39
The system board allows you to connect a LCD Display Panel by means of the LVDS
LCD panel connector and the LCD/Inverter power connector. These connectors transmit
video signals and power from the system board to the LCD Display Panel.
Refer to the right side for the pin functions of these connectors.
Jumper Settings
Refer to the “Jumper Settings” section in this chapter for settings relevant to the LCD
panel.
Function
Pin
LCD/Inverter Power Connector
Function
1
GND
2
GND
3
LVDSA_Out3+
4
LVDSB_Out3+
5
LVDSA_Out3-
6
LVDSB_Out3-
7
GND
8
GND
9
LVDSA_Out2+
10
LVDSB_Out2+
11
LVDSA_Out2-
12
LVDSB_Out2-
13
GND
14
GND
15
LVDSA_Out1+
16
LVDSB_Out1+
17
LVDSA_Out1-
18
LVDSB_Out1-
19
GND
20
GND
21
LVDSA_Out0+
22
LVDSB_Out0+
23
LVDSA_Out0-
24
LVDSB_Out0-
25
GND
26
GND
27
LVDSA_CLK+
28
LVDSB_CLK+
29
LVDSA_CLK-
30
LVDSB_CLK-
31
GND
32
GND
33
LVDS_DDCCLK
34
N.C.
35
LVDS_DDCDATA
36
N.C.
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
Pin
Function
1
GND
2
GND
3
Panel Inverter Brightness Voltage Control
4
Panel Power
5
+3.3V
6
Panel Backlight On/Off Control
7
LCD/Inverter Power
8
LCD/Inverter Power
19
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
eDP Connector
eDP Connector
Pin
1
eDP Connector
1
40
The eDP connector is an embedded displayport which has advanced power-saving features
to connect a display device to transmit digital communication of audio and video signals. The
table on the right indicates the pin functions of the eDP connector.
Function
Pin
Function
1
NC
21
eDP Panel PWR
2
GND
22
NC
3
eDP_Lane 3-
23
GND
4
eDP_Lane 3+
24
GND
5
GND
25
GND
6
eDP_Lane 2-
26
GND
7
eDP_Lane 2+
27
Hot Plug
8
GND
28
eDP_GND
9
eDP_Lane 1-
29
eDP_GND
10
eDP_Lane 1+
30
eDP_GND
11
GND
31
eDP_GND
12
eDP_Lane 0-
32
Panel Backlight On/Off Control
13
eDP_Lane 0+
33
Panel Inverter Brightness Voltage
Control
14
GND
34
NC
15
AUX+
35
NC
16
AUX-
36
Inverter PWR
17
GND
37
Inverter PWR
18
eDP Panel PWR
38
Inverter PWR
19
eDP Panel PWR
39
Inverter PWR
20
eDP Panel PWR
40
NC
20
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LPC Female Header
Pin
Function
Pin
Function
1
L_CLK
2
L_AD1
3
L_RST#
4
L_AD0
5
L_FRAME#
6
3V3
7
L_AD3
8
GND
9
L_AD2
10
---
11
L_SERIRQ
12
GND
13
5VSB
14
5V
LPC Female Header
13
1
14
2
1
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s
transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O
components within the system, which are typically provided by a Super I/O controller. Furthermore, it can be used to interface firmware hubs, Trusted Platform Module (TPM) devices and
embedded controller solutions. Data transfer on the LPC bus is implemented over a 4 bit serialized data interface, which uses a 33MHz LPC bus clock. For more information about LPC bus
refer to the Intel® Low Pin Count Interface Specification Revision 1.1’. The table on the right
indicates the pin fuctions of the LPC connector.
21
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
SATA (Serial ATA) Connectors
Cooling Fan Connector
System Fan
Power
Ground Sense
1
3
SATA 3.0
SATA 0
SATA 1
1
1
SATA 2
SATA 3
1
GND
RXP
RXN
GND
TXN
TXP
GND
7
Features
•
Four Serial ATA 3.0 ports with data transfer rate up to 6Gb/s
•
Integrated Advanced Host Controller Interface (AHCI) controller
The fan connector is used to connect cooling fan. The cooling fan will provide adequate airflow
throughout the chassis to prevent overheating the CPU and system board components.
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA cable to a SATA connector and the other end to your Serial ATA device.
BIOS Settings
Refer to the module’s BIOS for more information.
22
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
I2C Connector
SMBus Connector
I2C
1
I C_DATA
GND
21
NC
I2C_Clock
3VDU
1
5
2
SMBUS_Data
GND
SMBus
2
1
5
3VDU
SMBUS_CLK
SMBUS_Alert#
The 1-channel I2C bus interface conforms to the version 2.1 I2C bus specification. It operates
as a master or slave device and supports a multi-master bus.
The SMBus (System Management Bus) connectors are used to connect the SMBus device. It is
a multiple device bus that allows multiple chips to connect to the same bus and enable each
one to act as a master by initiating data transfer.
23
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Power Connectors
VGA Connector
13
15
1
+3.3VDC
+3.3VDC
-12VDC
+3.3VDC
GND
+5VDC
GND
PS_ON#
GND
GND
GND
NC
+5VDC
+5VDC
+5VDC
GND
GND
+5VDC
GND
PWR_OK
+5VSB
+12VDC
+12VDC
+3.3VDC
VGA
2 1
1
1
24 12
+12V
+12V
4
2
Ground
Ground
3
1
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place. The table below indicates the
pin fuctions of the VGA connector.
Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1.
An ATX12V power supply unit has a standard 24-pin ATX main power connector that must be
inserted into the 24-pin connector. The 4-pin +12V power connector enables the delivery of
more +12VDC current to the COM express module board and carrier board’s PCIe device.
Pin
The power connectors from the power supply unit are designed to fit the 24-pin and 4-pin
connectors in only one orientation. Make sure to find the proper orientation before plugging
the connectors.
Important:
The system board consumes a minimal amount of power. Due to its low power
consumption, you only need a 120W to 150W power supply. Every power supply has
its minimum load of power. If you use a greater than 150W power supply, the power
consumed by the system board may not attain its minimum load causing instability to
the entire system.
Pin Assignment
Pin
Pin Assignment
1
VGA_RED_C
2
VGA_GRE_C
3
VGA_BLE_C
4
N.C.
5
GND
6
CRT_DET
7
GND
8
GND
9
+5V
10
GND
11
N.C.
12
DDCSDA_5V-R
13
HSYNC_C
14
VSYNC_C
15
DDCSCL_5V-R
24
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Front Panel Connector
N.C.
HDD-LED
RESET-SW
Front Panel
1
2
N.C.
Pin
Pin Assignment
Pin
Pin Assignment
1
N.C.
2
LED Power
3
HDD Power
4
LED Power
5
Signal
6
Signal
7
Ground
8
Ground
9
RST Signal
10
Signal
11
N.C.
PWR-LED
PWR-BTN
PWR-LED
1
HDD-LED
PWR-BTN
RESET-SW
11 12
HDD-LED - HDD LED
This LED will light when the hard drive is being accessed.
RESET-SW - Reset Switch
This switch allows you to reboot without having to power off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power
On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To
RAM) state, it will blink every 4 seconds.
PWR-BTN - ATX Power Switch
Depending on the setting in the BIOS setup, this switch is a “dual function power button” that
will allow your system to enter the Soft-Off or Suspend mode.
25
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Standby Power LED
Battery
RTC Battery
Standby
Power LED
1
1
This LED will lit red when the system is in the standby mode. It indicates that there is power
on the system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
The lithium ion battery (CR2032 coin cell) powers the real-time clock and CMOS memory. It is
an auxiliary source of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to local ordinance.
26
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Expansion Slots
M.2 (M Key) Socket
The M.2 socket is the Next Generation Form Factor (NGFF) which is designed to support multiple modules and make the M.2 more suitable in application for solid-state storage.
PCI Express x1 Slot
Install PCI Express cards such as network cards or other cards that comply to the PCI Express
specifications into the PCI Express x1 slot.
PCI Express x16 Slot
Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into the
PCI Express x16 slot. To install a graphics card into the x16 slot, align the graphics card above
the slot then press it down firmly until it is completely seated in the slot. The retaining clip of
the slot will automatically hold the graphics card in place.
1
PCIe 2
(PCIe x1)
PCIe 1
(PCIe x16)
PCIe 5
(PCIe x1)
PCIe 3
(PCIe x1)
PCIe 4
(PCIe x1)
M.2
27
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM Express Connectors
-
"+ =4<- >
COM Express
Connectors (Type 6)
-
"+ =4<- >
-
"+ =4<- >
"8-J A
"8-J5#K
"+
"+
A
"8-J AU
3J45-K
768J66<
768J66#<
H
"8-J3+: K
3J5 768J66<U
768J66#<U
"8-J3+: K
3J5
"+
"+
E
"8-J 3J5
768J66<
768J66#<
F
"8-J U
3J5 A
768J66< U
768J66#< U
"8-J3+:K
3J VK
"+
"+
"8-J 3J V K
768J66<
768J66#<
768J66#< U
"8-J U
3J3:
768J66< U
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"8-J 18#+K
768J66<A
768J66#<A
A
"8-J U
68J:
768J66<AU
768J66#<AU
H
"8-J#-4
68J 5#
"+
"+
676J6AK
68J53-#K
J5EU
J#33:J57<U
E
65#5J#<U
65#5 J#<U
J5E
J#3 5#5J57<
F
65#5J#<
65#5 J#<
69
676J6HK
676J6#5#K
69
65#5J<U
65#5 J<U
-J<EU
-J#<EU
-J#<E
1
The COM Express connectors are used to interface the carrier board with a COM Express
board. Refer to the following pages for the pin functions of these connectors.
-
"+ =4<- >
69
69
65#5J<
65#5 J<
-J<E
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
65#5 J#<U
65#5AJ#<U
-J<FU
-J#<FU
-J<F
A
65#5 J#<
65#5AJ#<
H
676J6K
1J,:
J2
69
-J#<F
65#5 J<U
65#5AJ<U
J5HU
69
E
65#5 J<
65#5AJ<
J5H
J5U
F
85#3,1K
1 #
69
=6>5#5J5#K
5G2 5J6 +
69
5G2 5J6;+
5G2 5J6 +
A
5G2 5J6#K
5G2 5J6 +
A
"+ =4<- >
"+ =4<- >
A
5G2 5J8#3:
6:
J#33:J57<U
J5 U
AA
5G2 5J6 ,7#
J:
J#3 5#5J57<
J5
AH
8,6J 6K
J 5#
A
#2#K
#2K
J5
69
J5U
J5
"+ =4<- >
J
69
J57<J6-3
J5 U
J5
"+ =4<- >
J
69
J57<J6-3
AE
768E
768F
AJ#33:J57<U
J5AU
AF
768EU
768FU
AJ#3 5#5J57<
J5A
A
768JEJFJ,K
768JHJJ,K
AJ
A
768H
768
AJ5U
H
768HU
768U
H
"+ =4<- >
"+ =4<- >
J57<J6-3
69
J5U
AJ5
J5
"+ =4<- >
"+ =4<- >
28
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
-
-
-
-
-
-
-
768
768A
AJ5 U
J5 U
6J,1-
9"5J"+
-"J<
HA
768 U
768AU
AJ5
J5
6J6,
9"5J837
-"J<
HH
768J JAJ,K
768JJ J,K
J2
A
",
9"5J26;+
"+
"+
H
768
768
H
6J3:
9"5J96;+
-"J< AU
-"J#< AU
-"J#< A
HE
768U
768 U
HF
9J#
-<
J-6#K
H
-< J-6#K
-<
J-K
H
-< J-K
AJ2
69
6;6J-6-#K
69
U
-
H
AJ5 U
J5 U
6J,6
9"5J J:
-"J< A
AJ5
J5
E
#J
9"5J J 5#
"+
F
#;- K
6J6K
69
69
69
AJ5AU
J5AU
6-J#<
69
-"J#<
U
-"J#<
"+
69
-"J< HU
-"J#< HU
-"J< H
-"J#< H
3J6-V
8J-6-#K
AJ5A
J5A
6-J<
69
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
-J#<U
-J<U
-"J<U
-"J#<U
6- J#<
45+J10,7#
-"J< U
-"J#< U
A
-J#<
-J<
-"J<
-"J#<
6- J<
45+J#52+
-"J< -"J#< H
"
",
#;-K
-"J35+-J9K
A
3 K
63--K
"+
-J#<HU
-J<HU
-"J< U
-"J#< U
H
9J
9
9J
9
9J
9
9J
9
E
-J#<H
-J<H
-"J<
-"J#<
9J
9
9J
9
9J
9
9J
9
F
"+
",
#;- K
#;- K
E
9J
9
9J
9
9J
9
9J
9
-J#<AU
-J<AU
-"J< U
-"J#< U
F
9J
9
9J
9
9J
9
9J
9
-J#<A
-J<A
-"J<
-"J#<
9J
9
9J
9
9J
9
9J
9
E
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
9J
9
9J
9
9J
9
9J
9
E
-J#< U
-J< U
-"J<AU
-"J#<AU
E
-J#<
-J<
-"J<A
-"J#<A
EA
"
",A
69
69
EH
-J#< U
-J< U
69
69
E
-J#<
-J<
-"J<HU
-"J#<HU
EE
"+
15:-K
-"J<H
-"J#<H
EF
"
15:- K
69
E
-J#<U
-J<U
-"J<U
-"J#<U
E
-J#<
-J<
-"J<
-"J#<
F
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
F
39 6J5U
39 6J8U
-"J<EU
-"J#<EU
39 6J5
39 6J8
-"J<E
-"J#<E
FA
39 6J5 U
39 6J8 U
"+
"+
FH
39 6J5
39 6J8
-"J<FU
-"J#<FU
F
39 6J5 U
39 6J8 U
-"J<F
-"J#<F
FE
39 6J5
39 6J8
"+
"+
FF
39 6J9
39 6J8AU
69
F
39 6J5AU
39 6J8A
-"J<U
-"J#<U
-"J#<
69
"+ =4<- >
"+ =4<- >
"+ =4<- >
F
39 6J5A
39 6J8:3#J-+
-"J<
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
39 6J5J:U
39 6J8J:U
-"J<U
-"J#<U
39 6J5J:
39 6J8J:
-"J<
-"J#<
A
39 6J J:
39 6J8:3#J#3
69
H
39 6J J 5#
9J9J68;
"+
"+
"A
9J9J68;
-"J< U
-"J#< U
E
69
9J9J68;
-"J< -"J#< F
J2
9J9J68;
"+
-J3:J-4U
8,6J 6 K
-"J<
-J3:J-4
9"5J-
-"J<
-"J#<
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+ =4<- >
"+
F
J-+
"+
69
"+
U
-"J#<
U
29
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
SDIO
Serial Interface Connectors
SDIO
RX0
GND
TX0
1
Serial Interface 0 (Rx/Tx)
1
1
RX1
GND
TX1
1
Serial Interface 1 (Rx/Tx)
This expansion port is used to insert a Secure Digital Input/Output (SDIO) or Multimedia Card
(MMC) device. Aside from storing data files, an SDIO card is also capable of storing powerful
software applications.
This serial interface connectors are used to any device supported Tx and Rx signal.
30
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Switches
LAN Link LED
1
1
LAN Link LED
Power
Reset
Sleep
Lid
The LAN link LED shows the status of internet connection. The table below indicates the LED
definitions.
Note:
The Sleep and Lid functions are supported only when your operating system supports
ACPI.
•
•
Link/Act
Lid: It is used to turn the LVDS on or off.
Sleep: It is used to set the system to “sleep” or “wake-up” mode.
Speed
Color
Yellow
Amber
Green
On
Link-Up
1000Mbps
100Mbps
Off
Link-Down
Blink
Transmitting Data
100Mbps
N/A
N/A
31
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Thermal Trip LED
WatchDog Output LED
1
1
Thermal Trip LED
WatchDog
Output LED
This LED will light to indicate that the processor is on an overheating status.
A watchdog timer is a hardware timer that automatically generates a system reset if there are
any software anomalies. This LED will light when the watchdog timer is functioning.
32
Chapter 2 Hardware Installation
www.dfi.com
Chapter 3
Chapter 3 - Supported Software
Audio Driver
Please download drivers, utilities and software applications required to enhance the performance of the system board at https://www.dfi.com/DownloadCenter .
To install the driver, download “COM332-B(R.B1) Audio Driver” zip file at our website.
1. Setup is ready to install the
driver. Click “Next”.
2. Click “Yes, I want to restart
my computer now” then
click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
33
Chapter 3 Supported Software
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising