Dfi HD332-H81 Manual
HD332-H81
MicroATX Industrial Motherboard
User’s Manual
A34310548
1
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2015. All Rights Reserved.
Notice:
Trademarks
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2
Table of Contents
I/O Connectors ........................................................................................... 23
SATA (Serial ATA) Connectors ...................................................................... 23
Cooling Fan Connectors............................................................................... 24
Front Panel Connector ................................................................................ 24
Power Connectors ....................................................................................... 25
Chassis Intrusion Connector ........................................................................ 25
Expansion Slots .......................................................................................... 26
Parallel Port ................................................................................................ 26
SMBus Connector ....................................................................................... 27
Standby Power LED .................................................................................... 27
LPC Connector ............................................................................................ 28
Battery ....................................................................................................... 28
Copyright............................................................................................................. 2
Trademarks ........................................................................................................ 2
FCC and DOC Statement on Class B ..................................................... 2
About this Manual .......................................................................................... 4
Chapter 3 - BIOS Setup ............................................................... 29
Warranty.............................................................................................................. 4
Overview ..................................................................................................... 29
AMI BIOS Setup Utility ............................................................................. 30
Static Electricity Precautions...................................................................... 4
Main .......................................................................................................... 30
Advanced ................................................................................................... 30
Chipset ...................................................................................................... 41
Boot........................................................................................................... 48
Security...................................................................................................... 49
Save & Exit ................................................................................................ 49
Safety Measures .............................................................................................. 4
About the Package ......................................................................................... 5
Chapter 1 - Introduction ............................................................................. 6
Updating the BIOS .................................................................................... 50
Notice: BIOS SPI ROM ............................................................................. 50
Specifications ................................................................................................ 6
Features .......................................................................................................... 7
Chapter 4 - Supported Software ........................................................... 51
Chapter 2 - Hardware Installation................................................ 9
Chapter 5 - Digital I/O Programming Guide.................................... 71
Board Layout ................................................................................................. 9
System Memory ............................................................................................ 9
Appendix A - Watchdog Sample Code................................................ 73
Installing the DIMM Module ........................................................................ 10
Appendix B - Troubleshooting ................................................................74
CPU ................................................................................................................ 11
Installing the CPU ....................................................................................... 12
Installing the Fan and Heat Sink.................................................................. 14
Jumper Settings ......................................................................................... 15
Clear CMOS Data ........................................................................................ 15
PS/2 Keyboard/Mouse Power Select ............................................................. 15
USB Power Select ....................................................................................... 16
Power-on Select.......................................................................................... 16
COM 10 RS232/422/485 Select.................................................................... 17
COM 10 RS232/Power Select ....................................................................... 18
SATA DOM Power Select ............................................................................. 18
Rear Panel I/O Ports ................................................................................. 19
PS/2 Keyboad/Mouse Port ........................................................................... 19
COM (Serial) Ports ...................................................................................... 20
Graphics Interfaces ..................................................................................... 21
RJ45 LAN Ports........................................................................................... 21
USB Ports ................................................................................................... 22
Audio ......................................................................................................... 23
3
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
2. Wear an antistatic wrist strap.
1. Warranty does not cover damages or failures that arised from misuse of the product, inability to use the product, unauthorized replacement or alteration of components and product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
4
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
•
•
•
•
•
One
One
One
One
One
HD332 motherboard
Serial ATA data cable
I/O shield
DVD
QR (Quick Reference)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
•
•
•
•
•
USB port cable
COM port cable
Serial ATA data cable
I/O shield
Heat sink with fan
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
•
•
•
A CPU
Memory module
Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1
Chapter 1 - Introduction
Specifications
Processor
• LGA 1150 socket for:
- 4th Generation Intel® CoreTM processors
: Intel® CoreTM i7-4790S (8M Cache, up to 4.0 GHz); 65W
: Intel® CoreTM i7-4770S (8M Cache, up to 3.9 GHz); 65W
: Intel® CoreTM i7-4770TE (8M Cache, up to 3.3 GHz); 45W
: Intel® CoreTM i5-4590S (6M Cache, up to 3.7 GHz); 65W
: Intel® CoreTM i5-4590T (6M Cache, up to 3.0 GHz); 35W
: Intel® CoreTM i5-4570S (6M Cache, up to 3.6 GHz); 65W
: Intel® CoreTM i5-4570TE (4M Cache, up to 3.3 GHz); 35W
: Intel® CoreTM i3-4360 (4M Cache, 3.7 GHz); 54W
: Intel® CoreTM i3-4350T (4M Cache, 3.1 GHz); 35W
: Intel® CoreTM i3-4340TE (4M Cache, 2.6 GHz); 35W
: Intel® CoreTM i3-4330 (4M Cache, 3.5 GHz); 54W
: Intel® CoreTM i3-4330TE (4M Cache, 2.4 GHz); 35W
: Intel® Pentium® G3420 (3M Cache, 3.2 GHz); 53W
: Intel® Pentium® G3320TE (3M Cache, 2.3 GHz); 35W
: Intel® Celeron® G1820 (2M Cache, 2.7 GHz); 53W
: Intel® Celeron® G1820TE (2M Cache, 2.2 GHz); 35W
• 22nm process technology
Chipset
• Intel® H81 Express Chipset
Super I/O
Address
• NCT6102/4Eh (HD332-H81B)
• NCT6106/4Eh (HD332-H81X)
System Memory
•
•
•
•
•
Two 240-pin DDR3 DIMM sockets
Supports DDR3 1333/1600MHz when operating at 1.5V
Supports dual channel memory interface
Supports up to 16GB system memory
DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM technologies are
supported for x8 and x16 devices, unbuffered, non-ECC
Expansion Slots
• 1 PCIe x16 Gen 3 slot (PCIe 3.0)
• 2 PCIe x1 Gen 2 slots (PCIe 2.0)
• 1 PCI slot (PCI 2.3)
Graphics
•
•
•
•
•
•
•
•
Audio
• Realtek ALC888 5.1-channel High Definition Audio
• Audio outputs: Mic-in/Center+Subwoofer, Line-in/Surround and Line-out
LAN
Serial ATA
Intel® HD Graphics
Display ports: 1 VGA, 1 VGA/DVI-I (DVI-D signal)
VGA: 24-bit, resolution up to 1920x1200 @60Hz
DVI-D: resolution up to 1920x1200 @60Hz
Supports 20 Graphics Execution Units (EUs)
Intel® Clear Video Technology
DirectX Video Acceleration (DXVA) support for accelerating video processing
Supports DirectX 11.1 and OpenGL 4.0
®
• 2 Intel 82574L Gigabit Ethernet Controllers; or
2 Intel® I210 PCI Express Gigabit Ethernet controllers* (optional)
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• 2 SATA 3.0 ports with data transfer rate up to 6Gb/s
• 2 SATA 2.0 ports with data transfer rate up to 3Gb/s
- SATA port 1 provides adequate space for SATA DOM
• Integrated Advanced Host Controller Interface (AHCI) controller
Rear Panel I/O
Ports
• 1 mini-DIN-6 port for PS/2 mouse/keyboard
• 2 DB-9 RS232 serial ports
• 2 VGA ports; or
1 VGA and 1 DVI-I ports
• 2 RJ45 LAN ports
• 4 USB 3.0 ports
• 2 USB 2.0 ports
• Line-in/Surround, Line-out, Mic-in/Center+Subwoofer jacks
I/O Connectors
• 2 connectors for 4 external USB 2.0 ports and
1 vertical USB 2.0/1.1 port; or
3 connectors for 6 external USB 2.0 ports* (optional)
• 8 connectors for 8 external serial ports (2.0mm pitch)
- 1 RS232/RS422/RS485 (RS232 and/or power)* (optional)
- 7 RS232
• 1 parallel connector
• 4 Serial ATA connectors
• 1 24-pin ATX power connector
• 1 8-pin 12V power connector
• 1 chassis intrusion connector
• 1 front panel connector
• 2 fan connectors
USB
Interface
• XHCI Host Controller supports up to 2 super speed USB 3.0 ports
Trusted Platform
Module - TPM*
(optional)
• Provides a Trusted PC for secure transactions
• Provides software license protection, enforcement and password protection
BIOS
• AMI BIOS
- 64Mbit SPI BIOS
WatchDog Timer
• Software programmable from 1 to 255 seconds
Energy Efficient
Design
•
•
•
•
Damage Free
Intelligence
•
•
•
•
Power
Consumption
• HD332-H81X (VGA+DVI/VGA): 69.10W with i7-4770S at 3.10GHz and 2x 4GB
DDR3 DIMM
Supports ErP Lot6 power saving* (optional)
Supports ACPI
System Power Management
Wake-On-Events include:
- Wake-On-PS/2 KB/Mouse
- Wake-On-USB KB/Mouse
- Wake-On-LAN
- RTC timer to power-on the system
• CPU stopped clock control
• AC power failure recovery
Monitors CPU/system temperature and overheat alarm
Monitors VCORE/5V/3.3V/V_DIMM/12V/3VSB/VBAT voltages and failure alarm
Monitors CPU/system fan speed and failure alarm
Read back capability that displays temperature, voltage and fan speed
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Features
Temperature
• Operating: 0oC to 60oC
• Storage: -20oC to 85oC
Humidity
• 5% to 90%
• Watchdog Timer
OS Support
•
•
•
•
•
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
Dimensions
• microATX form factor
• 244mm (9.6") x 244mm (9.6")
Certification
• CE, FCC Class B, RoHS
Windows
Windows
Windows
Windows
Windows
XP Professional x86 & SP3 (32-bit) (limited function)
7 Ultimate x86 & SP1 (32-bit)
7 Ultimate x64 & SP1 (64-bit)
8 Enterprise x86 (32-bit)
8 Enterprise x64 (64-bit)
• DDR3
DDR3 delivers increased system bandwidth and improved performance. It offers peak data
transfer rate of up to 16Gb/s bandwidth. The advantages of DDR3 are its higher bandwidth
and its increase in performance at a lower power than DDR2.
• Graphics
Note:
*Optional and is not supported in standard model. Please contact your sales representative for more information.
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications.
• PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes. The PCI Express architecture also supports high performance graphics infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 3Gb/s (SATA 2.0) and 6Gb/s (SATA 3.0), it improves hard drive performance faster than
the standard parallel ATA whose data transfer rate is 100MB/s. The bandwidth of the SATA 3.0
will be limited by carrier board design.
• Gigabit LAN
Two Intel® Gigabit LAN controllers, Intel® 82574L Gigabit Ethernet controllers or Intel® I210
PCI Express Gigabit Ethernet controllers (optional), support up to 1Gbps data transmission.
• Audio
The Realtek ALC888 audio codec provides 5.1-channel High Definition audio output.
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
• Wake-On-LAN
• Wake-On-PS/2
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Management Event) signal. However, if your system is in the Suspend mode, you can power-on
the system only through an IRQ or DMA interrupt.
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
• Wake-On-USB
• USB
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
The system board supports the new USB 3.0. It is capable of running at a maximum transmission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously
accessible external Plug and Play peripherals.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the 5V_standby power source of your power supply must support ≥2A.
• RTC Timer
The RTC installed on the system board allows your system to automatically power-on on the
set date and time.
• ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to
go through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
8
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
© 2015. All Rights Reserved.
Notice:
Trademarks
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2
Table of Contents
I/O Connectors
...........................................................................................23
SATA (Serial ATA) Connectors ...................................................................... 23
Cooling Fan Connectors............................................................................... 24
Front Panel Connector ................................................................................ 24
Power Connectors ....................................................................................... 25
Chassis Intrusion Connector ........................................................................ 25
Expansion Slots .......................................................................................... 26
Parallel Port ................................................................................................ 26
SMBus Connector ....................................................................................... 27
Standby Power LED .................................................................................... 27
LPC Connector ............................................................................................ 28
Battery ....................................................................................................... 28
Copyright............................................................................................................. 2
Trademarks ........................................................................................................2
FCC and DOC Statement on Class B
About this Manual
..................................................... 2
..........................................................................................4
Chapter 3 - BIOS Setup
Warranty.............................................................................................................. 4
Overview .....................................................................................................29
AMI BIOS Setup Utilit y .............................................................................30
Static Electricity Precautions ...................................................................... 4
Main ..........................................................................................................30
Advanced ...................................................................................................30
Chipset ...................................................................................................... 41
Boot........................................................................................................... 48
Security...................................................................................................... 49
Save & Exit ................................................................................................ 49
Safety Measures ..............................................................................................4
About the P ackage .........................................................................................5
Chapter 1 - Introduction
............................................................... 29
.............................................................................6
Updating the BIOS .................................................................................... 50
Notice: BIOS SPI ROM .............................................................................50
Specifications ................................................................................................6
Features ..........................................................................................................7
Chapter 4 - Supported Softw are ...........................................................51
Chapter 2 - Hardw are Installation ................................................ 9
Chapter 5 - Digital I/O Progr amming Guide .................................... 71
Board Layout .................................................................................................9
System Memory ............................................................................................ 9
Appendix A - W atchdog Sample Code ................................................ 73
Installing the DIMM Module ........................................................................ 10
Appendix B - Troubleshooting ................................................................ 74
CPU ................................................................................................................11
Installing the CPU ....................................................................................... 12
Installing the Fan and Heat Sink.................................................................. 14
Jumper Settings ......................................................................................... 15
Clear CMOS Data ........................................................................................ 15
PS/2 Keyboard/Mouse Power Select ............................................................. 15
USB Power Select ....................................................................................... 16
Power-on Select.......................................................................................... 16
COM 10 RS232/422/485 Select .................................................................... 17
COM 10 RS232/P ower Select ....................................................................... 18
SATA DOM P ower Select ............................................................................. 18
Rear Panel I/O P orts .................................................................................19
PS/2 Keyboad/Mouse Port ........................................................................... 19
COM (Serial) P orts ...................................................................................... 20
Graphics Interfaces ..................................................................................... 21
RJ45 LAN Ports........................................................................................... 21
USB Ports ................................................................................................... 22
Audio .........................................................................................................23
3
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
2. Wear an antistatic wrist strap.
1. Warranty does not cover damages or failures that arised from misuse of the product, inability to use the product, unauthorized replacement or alteration of components and product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
4
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
•
•
•
•
•
One
One
One
One
One
HD332 motherboard
Serial ATA data cable
I/O shield
DVD
QR (Quick Reference)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
•
•
•
•
•
USB port cable
COM port cable
Serial ATA data cable
I/O shield
Heat sink with fan
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
•
•
•
A CPU
Memory module
Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
5
Chapter 1
Chapter 1 - Introduction
Specifications
Processor
• LGA 1150 socket for:
- 4th Generation Intel® CoreTM processors
: Intel® CoreTM i7-4790S (8M Cache, up to 4.0 GHz); 65W
: Intel® CoreTM i7-4770S (8M Cache, up to 3.9 GHz); 65W
: Intel® CoreTM i7-4770TE (8M Cache, up to 3.3 GHz); 45W
: Intel® CoreTM i5-4590S (6M Cache, up to 3.7 GHz); 65W
: Intel® CoreTM i5-4590T (6M Cache, up to 3.0 GHz); 35W
: Intel® CoreTM i5-4570S (6M Cache, up to 3.6 GHz); 65W
: Intel® CoreTM i5-4570TE (4M Cache, up to 3.3 GHz); 35W
: Intel® CoreTM i3-4360 (4M Cache, 3.7 GHz); 54W
: Intel® CoreTM i3-4350T (4M Cache, 3.1 GHz); 35W
: Intel® CoreTM i3-4340TE (4M Cache, 2.6 GHz); 35W
: Intel® CoreTM i3-4330 (4M Cache, 3.5 GHz); 54W
: Intel® CoreTM i3-4330TE (4M Cache, 2.4 GHz); 35W
: Intel® Pentium® G3420 (3M Cache, 3.2 GHz); 53W
: Intel® Pentium® G3320TE (3M Cache, 2.3 GHz); 35W
: Intel® Celeron® G1820 (2M Cache, 2.7 GHz); 53W
: Intel® Celeron® G1820TE (2M Cache, 2.2 GHz); 35W
• 22nm process technology
Chipset
• Intel® H81 Express Chipset
Super I/O
Address
• NCT6102/4Eh (HD332-H81B)
• NCT6106/4Eh (HD332-H81X)
System Memory
•
•
•
•
•
Two 240-pin DDR3 DIMM sockets
Supports DDR3 1333/1600MHz when operating at 1.5V
Supports dual channel memory interface
Supports up to 16GB system memory
DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM technologies are
supported for x8 and x16 devices, unbuffered, non-ECC
Expansion Slots
• 1 PCIe x16 Gen 3 slot (PCIe 3.0)
• 2 PCIe x1 Gen 2 slots (PCIe 2.0)
• 1 PCI slot (PCI 2.3)
Graphics
•
•
•
•
•
•
•
•
Audio
• Realtek ALC888 5.1-channel High Definition Audio
• Audio outputs: Mic-in/Center+Subwoofer, Line-in/Surround and Line-out
LAN
Serial ATA
Intel® HD Graphics
Display ports: 1 VGA, 1 VGA/DVI-I (DVI-D signal)
VGA: 24-bit, resolution up to 1920x1200 @60Hz
DVI-D: resolution up to 1920x1200 @60Hz
Supports 20 Graphics Execution Units (EUs)
Intel® Clear Video Technology
DirectX Video Acceleration (DXVA) support for accelerating video processing
Supports DirectX 11.1 and OpenGL 4.0
®
• 2 Intel 82574L Gigabit Ethernet Controllers; or
2 Intel® I210 PCI Express Gigabit Ethernet controllers* (optional)
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• 2 SATA 3.0 ports with data transfer rate up to 6Gb/s
• 2 SATA 2.0 ports with data transfer rate up to 3Gb/s
- SATA port 1 provides adequate space for SATA DOM
• Integrated Advanced Host Controller Interface (AHCI) controller
Rear Panel I/O
Ports
• 1 mini-DIN-6 port for PS/2 mouse/keyboard
• 2 DB-9 RS232 serial ports
• 2 VGA ports; or
1 VGA and 1 DVI-I ports
• 2 RJ45 LAN ports
• 4 USB 3.0 ports
• 2 USB 2.0 ports
• Line-in/Surround, Line-out, Mic-in/Center+Subwoofer jacks
I/O Connectors
• 2 connectors for 4 external USB 2.0 ports and
1 vertical USB 2.0/1.1 port; or
3 connectors for 6 external USB 2.0 ports* (optional)
• 8 connectors for 8 external serial ports (2.0mm pitch)
- 1 RS232/RS422/RS485 (RS232 and/or power)* (optional)
- 7 RS232
• 1 parallel connector
• 4 Serial ATA connectors
• 1 24-pin ATX power connector
• 1 8-pin 12V power connector
• 1 chassis intrusion connector
• 1 front panel connector
• 2 fan connectors
USB
Interface
• XHCI Host Controller supports up to 2 super speed USB 3.0 ports
Trusted Platform
Module - TPM*
(optional)
• Provides a Trusted PC for secure transactions
• Provides software license protection, enforcement and password protection
BIOS
• AMI BIOS
- 64Mbit SPI BIOS
WatchDog Timer
• Software programmable from 1 to 255 seconds
Energy Efficient
Design
•
•
•
•
Damage Free
Intelligence
•
•
•
•
Power
Consumption
• HD332-H81X (VGA+DVI/VGA): 69.10W with i7-4770S at 3.10GHz and 2x 4GB
DDR3 DIMM
Supports ErP Lot6 power saving* (optional)
Supports ACPI
System Power Management
Wake-On-Events include:
- Wake-On-PS/2 KB/Mouse
- Wake-On-USB KB/Mouse
- Wake-On-LAN
- RTC timer to power-on the system
• CPU stopped clock control
• AC power failure recovery
Monitors CPU/system temperature and overheat alarm
Monitors VCORE/5V/3.3V/V_DIMM/12V/3VSB/VBAT voltages and failure alarm
Monitors CPU/system fan speed and failure alarm
Read back capability that displays temperature, voltage and fan speed
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Features
Temperature
• Operating: 0oC to 60oC
• Storage: -20oC to 85oC
Humidity
• 5% to 90%
• Watchdog Timer
OS Support
•
•
•
•
•
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
Dimensions
• microATX form factor
• 244mm (9.6") x 244mm (9.6")
Windows
Windows
Windows
Windows
Windows
XP Professional x86 & SP3 (32-bit) (limited function)
7 Ultimate x86 & SP1 (32-bit)
7 Ultimate x64 & SP1 (64-bit)
8 Enterprise x86 (32-bit)
8 Enterprise x64 (64-bit)
• DDR3
DDR3 delivers increased system bandwidth and improved performance. It offers peak data
transfer rate of up to 16Gb/s bandwidth. The advantages of DDR3 are its higher bandwidth
and its increase in performance at a lower power than DDR2.
• Graphics
Note:
*Optional and is not supported in standard model. Please contact your sales representative for more information.
The integrated Intel® HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with outstanding graphics responsiveness. These enhancements deliver the performance and compatibility needed for today’s and tomorrow’s business applications.
• PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes. The PCI Express architecture also supports high performance graphics infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 3Gb/s (SATA 2.0) and 6Gb/s (SATA 3.0), it improves hard drive performance faster than
the standard parallel ATA whose data transfer rate is 100MB/s. The bandwidth of the SATA 3.0
will be limited by carrier board design.
• Gigabit LAN
Two Intel® Gigabit LAN controllers, Intel® 82574L Gigabit Ethernet controllers or Intel® I210
PCI Express Gigabit Ethernet controllers (optional), support up to 1Gbps data transmission.
• Audio
The Realtek ALC888 audio codec provides 5.1-channel High Definition audio output.
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
• Wake-On-LAN
• Wake-On-PS/2
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Management Event) signal. However, if your system is in the Suspend mode, you can power-on
the system only through an IRQ or DMA interrupt.
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
• Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
• Wake-On-USB
• USB
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
The system board supports the new USB 3.0. It is capable of running at a maximum transmission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously
accessible external Plug and Play peripherals.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the 5V_standby power source of your power supply must support ≥2A.
• RTC Timer
The RTC installed on the system board allows your system to automatically power-on on the
set date and time.
• ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows® without having to
go through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support ≥720mA.
8
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Hardware Installation
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Board Layout
1
PS/2 KB/MS
USB 4-5
USB 2.0
2
2
6 9
1
COM 3
10
1
5
USB 4-5 or
PS/2 KB/MS
Nuvoton 4
Power Select
NCT5104D
(JP15)
COM
COM 22
COM 11
COM
ISL95820
5
1
2
1
2 1
2
9
10
9
10 9
10
COM 4
+12V
Power
System Fan
1
Nuvoton
NCT6106D
COM 5 COM 6
1
8
Parallel
Socket LGA1150
TPM
(optional)
1
Chassis
Intrusion
ASMedia
ASM1142
LAN 1
USB 3-4
USB 3.0
2
6 2
9
Important:
When the Standby Power LED lights red, it indicates that there is power on the system board. Power-off the PC then unplug the power cord prior to installing any devices. Failure to do so will cause severe damage to the motherboard and components.
1
9
COM 9
2
1
6
(JP17)
1
12
24
(JP18)
1
5 1
5
COM 10 RS232/422/485
Select (JP17/JP18)
2
6 2
6
1
5 1
5
COM 10 RS232/Power
Select (JP14)
COM 10
ATX
RS232/422/485
Power
Select (JP2)
1
USB 3-4 Power
Select (JP6)
Line-in
Line-out
Mic-in
System Memory
1
9
2
10
COM 10
10
Intel
82574L
USB 3.0
9
2
10
2
LAN 2
USB 1-2
26
10
COM 8
Buzzer
USB 1-2 Power
Select (JP5)
25
COM 7
VGA 1
VGA 2/DVI-I (DVI-D Signal)
1
2
1
CPU Fan
COM 2
COM 1
1
13
Power-on
1
Select (JP10)
Battery
Intel
82574L
Standby
Power LED
DDR3_1 DDR3_2
DDR3-1
PCIe x16
DDR3-2
Realtek
ALC888
PCIe x1
Note:
SATA 1 supports SATA DOM.
iTE
IT8893E
SPI Flash
BIOS
SATA 3.0
Rear I/O
PCI
NXP
PTN3460
5
1
6
2
1
Intel
H81
SATA 0
SATA 1
2
Onboard I/O
12
Storage
1
SMBus
PCIe x1
USB 2-3/8/10-11
Power Select (JP8)
USB 2.0
USB 2-3
9
10
1
9
1
2 10
2
USB 10-11
•
HD332-H81B has LAN 1 only.
•
HD330-H81X: 10 COM (COM 1 to COM 10).
HD330-H81B: 2 COM (COM 1 and COM 2).
Clear CMOS
Data (JP9)
USB 8
1
4
1
USB 2.0
11
1
1
SATA DOM Power
Select (JP11)
Front
Panel
11
12
1
1
2
1
LPC
Standby
Power LED
Expansion
1
SATA 5
SATA 4
SATA 2.0
Features
•
Two 240-pin DDR3 DIMM sockets
•
Supports DDR3 1333/1600MHz when operating at 1.5V
•
Supports dual channel memory interface
•
Supports up to 16GB system memory
9
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Installing the DIMM Module
The system board supports the following memory interface.
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
Single Channel (SC)
Data will be accessed in chunks of 64 bits (8B) from the memory channels.
Dual Channel (DC)
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board.
Single Channel
Dual Channel
DIMMs are on the same channel.
DIMMs in a channel can be identical or
completely different. However, we highly
recommend using identical DIMMs.
Not all slots need to be populated.
4. Push the “ejector tabs” which are at the ends of the socket to the side.
Ejector tab
Ejector tab
DIMMs of the same memory configuration
are on different channels.
5. Note how the module is keyed to the socket.
Notch
Key
10
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
CPU
6. Grasping the module by its edges, position the module above the socket with the “notch”
in the module aligned with the “key” on the socket. The keying mechanism ensures the
module can be plugged into the socket in only one way.
The system board is equipped with a surface mount LGA 1150 socket. This socket is exclusively designed for installing a LGA 1150 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1150 socket comes with a protective
cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If
the cap is missing or the cap and/or contact pins are damaged, contact your dealer
immediately.
2. Make sure to keep the protective cap. RMA requests will be accepted and processed only if the LGA 1150 socket comes with the protective cap.
7. Seat the module vertically, pressing it down firmly until it is completely seated in the
socket.
Protective
cap
8. The ejector tabs at the ends of the socket will automatically snap into the locked position
to hold the module in place.
Note:
The system board used in the following illustrations may not resemble the actual
board. These illustrations are for reference only.
11
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been powered down.
Lift the load lever up to
the angle shown on the
photo.
2. Disconnect all power cords and cables.
3. Locate the LGA 1150 CPU
socket on the system
board.
Load lever
5. Lifting the load lever will at
the same time lift the load
plate.
Load
plate
COM 2
COM 1
6. Remove the protective cap
from the CPU socket. The
cap is used to protect the
CPU socket against dust
and harmful particles.
Remove the protective cap
only when you are about
to install the CPU.
Important:
The CPU socket must not come in contact with anything other than the CPU. Avoid
unnecessary exposure. Remove the protective cap only when you are about to install
the CPU.
4. Unlock the socket by pushing
the load lever down, moving
it sideways until it is released
from the retention tab; then
lift the load lever up.
Protective cap
Load lever
Retention tab
12
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
7. Insert the CPU into the
socket. The gold triangular
mark on the CPU must
align with the corner of
the CPU socket shown on
the photo.
8. Close the load plate then
push the load lever down.
While closing the load
plate, make sure the front
edge of the load plate
slides under the retention
knob.
9. Hook the load lever under
the retention tab.
Gold triangular mark
Retention knob
Load lever
Retention tab
Alignment key
The CPU’s notch will at
the same time fit into the
socket’s alignment key.
Alignment key
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
13
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Installing the Fan and Heat Sink
4. Rotate each push-pin according to the direction of
the arrow shown on top of
the pin.
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system
board.
Push down two pushpins
that are diagonally across
the heat sink. Perform the
same procedure for the
other two push-pins.
Note:
A boxed Intel® processor already includes the CPU fan and heat sink assembly. If your
CPU was purchased separately, make sure to only use Intel®-certified fan and heat
sink.
Heat sink
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of the
CPU. The thermal paste is usually supplied when you purchase the fan / heat sink assembly. Do not spread the paste all over the surface. When you later place the heat sink on
top of the CPU, the compound will disperse evenly.
“Unlocked” position
of push-pin
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel the
strip that covers the paste before you place the fan / heat sink on top of the CPU.
2. Place the heat sink on top
of the CPU. The 4 pushpins around the heat sink,
which are used to secure
the heat sink onto the system board, must match the
4 mounting holes around
the socket.
3. Orient the heat sink such
that the CPU fan’s cable is
nearest the CPU fan connector.
COM 2
COM 1
“Locked” position of
push-pin
5. Connect the CPU fan’s
cable to the CPU fan
connector on the system
board.
Mounting hole
CPU Fan connector
COM 2
COM 1
CPU Fan connector
COM 2
COM 1
14
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Jumper Settings
PS/2 Keyboard/Mouse Power Select
Clear CMOS Data
2 4 6
JP15
COM 2
COM 1
COM 2
COM 1
1 3 5
1-3 On: +5V
(default)
2 4 6
1 3 5
3-5 On:
+5V_standby
JP9
1 2 3
1-2 On: Normal
(default)
1 2 3
2-3 On:
Clear CMOS Data
JP15 is used to select the power of the PS/2 keyboard/mouse port. Selecting +5V_standby
will allow you to use the PS/2 keyboard or the PS/2 mouse to wake up the system.
If you encounter the followings,
Important:
The +5V_standby power source of your power supply must support ≥720mA.
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
you can reconfigure the system with the default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
1. Power-off the system and unplug the power cord.
2. Set JP9 pins 2 and 3 to On. Wait for a few seconds and set JP9 back to its default setting,
pins 1 and 2 On.
3. Now plug the power cord and power-on the system.
15
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
USB Power Select
Power-on Select
2 4 6
1 3 5
2-4 On: +5V
(default)
COM 2
COM 1
USB 4-5
(JP15)
1 2 3
COM 2
COM 1
2 4 6
USB 1-2
(JP5)
1 3 5
4-6 On:
+5V_standby
USB 3-4
(JP6)
3
2
1
1-2 On: +5V
(default)
JP10
1-2 On:
Power-on via power button
(default)
1 2 3
2-3 On:
Power-on via AC power;
Power-on via WOL after G3
3
2
1
2-3 On:
+5V_standby
USB 2-3/8/10-11
(JP8)
JP10 is used to select the method of powering on the system. If you want to use the power
button, set pins 1 and 2 to On.
JP5, JP6, JP8 and JP15 are used to select the power of the USB devices. Selecting +5V_standby will allow you to use a USB device to wake up the system.
To power-on via WOL after G3:
1. Set JP10 pins 2 and 3 to On.
2. Set the “Wakeup Event After G3” field to Enable.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
To power-on via AC Power:
1. Set JP10 pins 2 and 3 to On.
2. Set the “Wakeup Event After G3” field to Disable.
16
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM 10 RS232/422/485 Select
JP2
10 9
2 4 6
2 4 6
2 4 6
1 3 5
1-2 On: RS232
(default)
1 3 5
1 3 5
3-4 On: RS422
Full Duplex
5-6 On: RS485
JP17 and JP18
COM 2
COM 1
2 4 6
2 4 6
1 3 5
1 3 5
21
COM 10
JP18
3-5, 4-6 On:
RS422 Full Duplex/RS485
1-3, 2-4 On:
RS232 (default)
JP17
JP2
COM 10
10 9
CTSDSRDTRRXD
21
RS232
RIRTSGND
TXD
DCD-
10 9
10 9
NC.
NC.
NC.
TXD+
RXD+
NC.
NC.
TXDRXD21
RS422
Full Duplex
NC.
NC.
NC.
NC.
DATA+
NC.
NC.
NC.
DATA21
RS485
JP2, JP17 and JP18 are used to configure the COM port 10 to RS232, RS422 (Full Duplex) or
RS485.
The pin functions of the COM port 10 will vary according to these jumpers’ setting.
Note:
When COM 10 RS232/422/485 is selected, JP17 and JP18 must be set in accordance
to JP2.
17
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM 10 RS232/Power Select
SATA DOM Power Select
10 9
COM 2
COM 1
COM 2
COM 1
21
COM 10
JP14
2 4 6
1 3 5
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
2 4 6
SATA 1
1 3 5
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
JP11
JP14 is used to configure the Serial COM port 10 to pure RS232 or RS232 with power.
1 2 3
1 2 3
1-2 On: GND
(default)
2-3 On: +5V
JP11 is designed to select the power level for the Serial ATA port supporting SATA DOM.
Note:
SATA port 1 provides adequate space for SATA DOM.
18
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Rear Panel I/O Ports
PS/2 Keyboard/Mouse Port
PS/2 Keyboard/Mouse
COM 2
VGA 1
LAN 2
LAN 1
PS/2 KB/MS
COM 2
COM 1
Line-in/Surround
Line-out
Mic-in/
Center+Subwoofer
USB 2.0
COM 1
USB 3.0 USB 3.0
VGA 2 or
DVI-I (DVI-D Signal)
The rear panel I/O ports consist of the following:
•
•
•
•
•
•
•
•
•
1 PS/2 Keyboard/Mouse port
2 Serial COM ports
2 VGA ports; or 1 VGA and 1 DVI-I ports
2 RJ45 LAN ports
(HD332-H81B has LAN 1 only.)
4 USB 3.0 ports
2 USB 2.0 ports
Line-in/Surround jack
Line-out jack
Mic-in/Center+Subwoofer jack
This rear I/O port is used to connect a PS/2 mouse and a PS/2 keyboard. The PS/2 mouse
port uses IRQ12.
Wake-On-PS/2 Keyboard/Mouse
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power-on the system. To use this function:
• Jumper Setting
JP15 must be set to “3-5 On: +5V_standby”. Refer to “PS/2 Keyboard/Mouse Power Select” in
this chapter for more information.
• BIOS Setting
Configure the wake-up function of PS/2 keyboard/mouse in the Advanced menu (“ACPI Power
Management Configuration” submenu) of the BIOS. Refer to the chapter 3 for more information.
Important:
The +5V_standby power source of your power supply must support ≥720mA.
19
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
COM (Serial) Ports
COM 3 to COM 6:
RS232
1 2
DCDRXD
TXD
DTRDSRGND
RTSCTSRI9 10
COM 5
COM 3
COM 2
COM 4 COM 6
Note:
1. HD332-H81X: 10 COM (COM 1 to COM 10).
HD332-H81B: 2 COM (COM 1 and COM 2).
2. When COM 10 RS232/422/485 is selected, JP17 and JP18 must be set in
accordance to JP2.
COM 7 to COM 9:
RS232
10 9
RICTSRTSDSRGND
DTRTXD
RXD
DCD21
COM 2
COM 1
COM 7
COM 8
COM 9
COM 1
COM 10
10 9
COM 1/COM 2:
RS232
COM 10:
RS232/422/485
21
COM 1 to COM 9 are fixed at RS232.
The pin functions of the COM port 10 will vary according to jumpers’ setting. JP2, JP17 and
JP18 are used to configure the Serial COM port 10 to to RS232, RS422 (Full Duplex) or RS485
and JP14 allows you to configure it to pure RS232 or RS232 with power. Refer to “COM 10
RS232/422/485 Select” and “COM 10 RS232/Power Select“ in this chapter for more information.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
Connecting External Serial Ports
Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket to
an available slot at the rear of the system chassis then insert the serial port cable to the COM
connector. Make sure the colored stripe on the ribbon cable is aligned with pin 1 of the COM
connector.
BIOS Setting
Configure the serial COM ports in the Advanced menu (“Super IO Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
20
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Graphics Interfaces
RJ45 LAN Ports
The display ports consist of the following:
•
2 VGA ports; or 1 VGA and 1 DVI-I ports
COM 2
COM 1
VGA 1
COM 2
COM 1
LAN 2
LAN 1
LAN 2
LAN 1
VGA 2 or
DVI-I (DVI-D Signal)
Features
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
•
2 Intel® 82574L Gigabit Ethernet Controllers; or
2 Intel® I210 PCI Express Gigabit Ethernet controllers (optional)
The LAN ports allow the system board to connect to a local area network by means of a network hub.
DVI-I Port (DVI-D Signal)
The DVI-I port is used to connect an LCD monitor.
BIOS Setting
Connect the display device’s cable connector to the DVI-I port. After plugging the cable connector into the port, gently tighten the cable screws to hold the connector in place.
Configure the onboard LAN ports in the Chipset menu (“PCH-IO Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
BIOS Setting
Driver Installation
Configure the display devices in the Chipset menu (“System Agent Configuration” submenu) of
the BIOS. Refer to the chapter 3 for more information.
Install the LAN drivers. Refer to the chapter 4 for more information.
Note:
HD332-H81B supports 1 Intel® 82574L Gigabit Ethernet controller (LAN 1) only.
21
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
USB Ports
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function:
USB 5
•
COM 2
COM 1
USB 4
JP5, JP6, JP8 and JP15 must be set to “2-3 On: +5V_standby”. Refer to “USB Power Select” in
this chapter for more information.
USB 2.0
USB 2
USB 4
USB 1
USB 3
USB 3.0
Jumper Setting
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
USB 3.0
USB 8
USB 10-11
Key
GND
+Data
-Data
VCC
4
1
2
N. C.
GND
+Data
-Data
VCC
9
10
1
GND
-Data
+Data
VCC
USB 2-3
USB 2.0
USB 2.0
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with four onboard USB 3.0 ports (USB 1-2/USB 3-4) and two
onboard USB 2.0 ports (USB 4-5). The 10-pin connectors allows you to connect 4 additional
USB 2.0/1.1 ports (USB 2-3/USB 10-11) and the vertical USB connector is designed to connect
1 external USB 2.0/1.1 port (USB 8). The additional USB ports may be mounted on a cardedge bracket. Install the card-edge bracket to an available slot at the rear of the system chassis and then insert the USB port cables to a connector.
BIOS Setting
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to the chapter 3 for more information.
Driver Installation
You may need to install the proper drivers in your system operation to use the USB device.
Refer to your operating system’s manual or documentation for more information.
22
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
I/O Connectors
Audio
SATA (Serial ATA) Connectors
Rear Audio
COM 2
COM 1
COM 2
COM 1
Line-in/Surround
Line-out
1
7
GND
RXP
RXN
GND
TXN
TXP
GND
Mic-in/
Center+Subwoofer
SATA 0
SATA 1
SATA 3.0 6Gb/s
(SATA port 1 provides adequate
space for SATA DOM)
SATA 2.0 3Gb/s
1
Rear Audio
SATA 5
The system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
•
Line-in/Surround Jack (Light Blue)
This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player,
AM/FM radio tuner, synthesizer, etc.
•
Line-out Jack (Lime)
This jack is used to connect a headphone or external speakers.
•
SATA 4
Features
GND
RXP
RXN
GND
TXN
TXP
GND
7
•
4 Serial ATA connectors
- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s (SATA 0 and SATA 1)
- 2 SATA 2.0 ports with data transfer rate up to 3Gb/s (SATA 4 and SATA 5)
•
Integrated Advanced Host Controller Interface (AHCI) controller
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA data cable to a SATA connector and the other end to your Serial ATA device.
Mic-in/Center+Subwoofer Jack (Pink)
This jack is used to connect an external microphone.
BIOS Setting
Driver Installation
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to the chapter 3 for more information.
Install the audio driver. Refer to the chapter 4 for more information.
Note:
Some 3rd party SATA Gen 2 speed device controllers used on the system board paired
with the Intel® 8 series chipset are intermittently detected. Before using SSD devices
or mSATA SSD devices, please check whether the device and the cable which are
used on the system board conform to Intel's official regulations.
23
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Cooling Fan Connectors
1
Front Panel Connector
4
COM 2
COM 1
CPU Fan
Ground
Power
Sense
Speed Control
Ground
Power
Sense
System Fan
1
3
COM 2
COM 1
RESET-SW
HDD-LED
Front
Panel
1
2
11
12
HDD-LED - HDD LED
PWR-LED
ATX-SW
This LED will light when the hard drive is being accessed.
RESET SW - Reset Switch
This switch allows you to reboot without having to power off the system.
ATX-SW - ATX Power Switch
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power
On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend To
RAM) state, it will blink every 4 seconds.
These fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
BIOS Setting
Pin Pin Assignment
The Advanced menu (“PC Health Status” submenu) of the BIOS will display the current speed
of the cooling fans. Refer to chapter 3 for more information.
HDD-LED
RESET SW
Pin Pin Assignment
3
HDD Power
2
LED Power
5
Signal
PWR-LED 4
LED Power
7
Ground
6
Signal
9
RST Signal
8
Ground
11
N.C.
10
Signal
ATX-SW
24
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
Power Connectors
Chassis Intrusion Connector
+12V
Power
1
5
+12V
Ground
COM 2
COM 1
4
8
COM 2
COM 1
12 24
ATX power
+3.3V
GND
+12V
+5V
+12V
+5V
+5VSB
+5V
Chassis
Intrusion
Signal
Ground
1
2
-5V
PWR_OK
GND
GND
+5V
GND
GND
GND
+5V
PS_ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
1
13
Use a power supply that complies with the A TX12V P ower Supply Design Guide V ersion 1.1.
An ATX12V power supply unit has a standard 24-pin A TX main power connector that must be
inserted into the 24-pin connector . The 8-pin +12V power connector enables the deliv ery of
more +12VDC current to the processor ’s Voltage Regulator Module (VRM).
The board supports the chassis intrusion detection f
unction. Connect the chassis intrusion
sensor cable from the chassis to this connector . When the system’ s power is on and a chassis
intrusion occurred, an alarm will sound. When the system’ s power is of f and a chassis intrusion
occurred, the alarm will sound only when the system restarts.
The power connectors from the power supply unit are designed to fit the 24-pin and 8-pin
connectors in only one orientation. Mak e sure to find the proper orientation bef ore plugging
the connectors.
The system board requires a minimum of 300 W
att power supply to oper ate. Y our system
configuration (CPU power, amount of memory , add-in cards, peripher als, etc.) ma y ex ceed the
minimum power requirement. T o ensure that adequate power is pro vided, we strongly recommend that y ou use a minimum of 400 W att (or greater) power supply .
Important:
Insufficient power supplied to the system ma y result in instabilit y or the add-in boards
and peripherals not f unctioning properly. Calculating the system’ s approximate power
usage is important to ensure that the power supply meets the system’ s consumption
requirements.
25
Chapter 2 Hardw are Installation
www.df .com
Chapter 2
Expansion Slots
Parallel Port
1 2
Parallel
COM 2
COM 1
COM 2
COM 1
25 26
PCI Express x16
PCI Express x1
PCI
PCI Express x1
The 25-pin connector is used to connect an external parallel port. The parallel port connects
your PC to a parallel printer. It supports SPP, ECP and EPP.
PCI Express x16 Slot
Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into the
PCI Express x16 slot. To install a graphics card into the x16 slot, align the graphics card above
the slot then press it down firmly until it is completely seated in the slot. The retaining clip of
the slot will automatically hold the graphics card in place.
SPP
(Standard Parallel Port)
PCI Slot
ECP
(Extended Capabilities Port)
The PCI slot supports expansion cards that comply with PCI specifications. You can install a
PCI expansion card or a customized riser card designed for only 2 PCI slots expansion (for low
profile PCI card only) into the PCI slot.
EPP
(Enhanced Parallel Port)
Allows normal speed operation but in one
direction only.
Allows parallel port to operate in bidirectional
mode and at a speed faster than the SPP’s data
transfer rate.
Allows bidirectional parallel port operation at
maximum speed.
PCI Express x1 Slot
Install PCI Express cards such as network cards or other cards that comply to the PCI Express
specifications into the PCI Express x1 slot.
Note:
The parallel connector on the HD330-H81D system board is optional.
26
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
SMBus Connector
Standby Power LED
COM 2
COM 1
COM 2
COM 1
Standby Power LED
SMBUS_Alert#
SMBUS_CLK
+3.3V_standby
SMBus
NC
SMBUS_Data
GND
5
6
This LED will lit red when the system is in the standby mode. It indicates that there is power
on the system board. Power-off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
1
2
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
27
Chapter 2 Hardware Installation
www.dfi.com
Chapter 2
LPC Connector
Battery
COM 2
COM 1
COM 2
COM 1
Battery
LPC
1 2
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
11 12
Safety Measures
• Danger of explosion if battery incorrectly replaced.
The LPC connector is used for the debug function and its pin functions are listed below.
• Replace only with the same or equivalent type recommend by the manufacturer.
Pins
Pin Assignment
Pins
Pin Assignment
1
CLK
2
LAD1
3
RST#
4
LAD0
5
FRAME#
6
VCC_+3V
7
LAD3
8
GND
9
LAD2
10
x
SERIRQ
12
48MHz
11
• Dispose of used batteries according to local ordinance.
28
Chapter 2 Hardware Installation
www.dfi.com
Chapter 3
Chapter 3 - BIOS Setup
Legends
Overview
Keys
Function
Right and Left arrows
Moves the highlight left or right to select a menu.
Up and Down arrows
Moves the hightlight up or down between submenu or f elds.
<Esc>
Exit to the BIOS Setup Utility.
+ (plus key)
Scrolls forward through the values or options of the highlighted f eld.
- (minus key)
Scrolls backward through the values or options of the highlighted f eld.
Tab
Select a f eld.
<F1>
Displays general help
<F2>
Pervious values
Default Configuration
<F3>
Optimized defaults
Most of the configur ation settings are either predefined according to the Load Optimal Def aults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a f ew settings that y ou may need to change depending on
your system configur ation.
<F4>
Saves and resets the setup program.
<Enter>
Press <Enter> to enter the highlighted submenu.
The BIOS is a progr am that tak es care of the basic lev el of communication between the CPU
and peripherals. It contains codes f or various advanced features found in this system board.
The BIOS allows y ou to configure the system and sa ve the configur ation in a bat tery-backed
CMOS so that the data retains ev en when the power is of f. In gener al, the inf ormation stored
in the CMOS RAM of the EEPROM will sta y unchanged unless a configur ation change has been
made such as a hard driv e replaced or a device added.
It is possible that the CMOS bat tery will f ail causing CMOS data loss. If this happens, y ou need
to install a new CMOS bat tery and reconfigure the BIOS set tings.
Note:
The BIOS is constantly updated to impro ve the perf ormance of the system board;
therefore the BIOS screens in this chapter ma y not appear the same as the actual
one. These screens are f or reference purpose only.
Entering the BIOS Setup Utility
Scroll Bar
The BIOS Setup Utilit y can only be oper ated from the k eyboard and all commands are k eyboard commands. The commands are a vailable at the right side of each setup screen.
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow k eys to scroll through all
the available fields.
The BIOS Setup Utilit y does not require an oper ating system to run. After y ou power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “R eset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> k eys simultaneously.
Submenu
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are a vailable for that field. To display the submenu, mo ve the highlight to
that field and press <Enter>.
29
Chapter 3 BIOS Setup
www.df .com
Chapter 3
AMI BIOS Setup Utility
Advanced
Main
The Advanced menu allows y ou to configure y our system f or basic oper ation. Some entries are
defaults required by the system board, while others, if enabled, will impro ve the perf ormance
of your system or let y ou set some f eatures according to y our preference.
The Main menu is the first screen that y ou will see when y ou enter the BIOS Setup Utilit y.
Main
Important:
Setting incorrect field v alues may cause the system to malf unction.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Chipset
Save & Exit
Boot
Security
Choose the system default
language
BIOS Information
BIOS Vendor
Core Version
Compliancy
Project Version
Build Date and Time
American Megatrends
4.6.5.4
UEFI 2.3.1; PI 1.2
1AQQW 0.25 x64
01/20/2015 17:08:03
System Language
[English]
System Date
System Time
[Mon 02/02/2015]
[14:44:31]
Access Level
Administraor
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main

ACPI
Advanced
Chipset
Boot
Power Management Configuration

Trusted Computing

CPU Configuration

SATA Configuration

PCH-FW Configuration

USB Configuration

Super IO Configuration

PC Health Status

Second Super IO Configuration

Network Stack
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Security
Save & Exit
ACPI Power Management
Configuration
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
System Date
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
The date f ormat is <da y>, <month>, <date>, <y ear>. Day displays a da y, from Sunday to Saturda y. Month displa ys the month, from January to December . Date displa ys
the date, from 1 to 31. Y ear displays the y ear, from 1980 to 2099.
System Time
The time f ormat is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. F or example, 1 p .m. is 13:00:00. Hour displa ys hours from 00 to
23. Minute displa ys minutes from 00 to 59. Second displa ys seconds from 00 to 59.
30
Chapter 3 BIOS Setup
www.df .com
Chapter 3
ACPI Power Management Configuration
Trusted Computing
This section is used to configure the ACPI P ower Management.
This section configures set tings relevant to Trusted Computing inno vations.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
ACPI Power Management Configuration
Resume by PME
Resume by Ring
Resume by RTC Alarm
[Disabled]
[Disabled]
[Disabled]
Wakeup Event After G3
[Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Configuration
Security Device Support
About Resume by PME
(PCI, PCIE, LAN). If
PME is enabled then PCH
After-G3 function is enabled, too. But Auto Power
on function is fail.
Current Status Information
No Security Device Found
[Disable]
Enables or Disables
BIOS support for security
device. O.S will not show
Security Device. TCG
EFI protocol and INT1A
interface will not be
available.


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Security Device Support
This field is used to enable or disable BIOS supporting f or the securit y device. O .S will
not show the securit y device. T CG EFI protocol and INT1A interf ace will not be
available.
Resume by PME
Enables this field to use the PME signal to w ake up the system.
Resume by Ring
Enables this field to use the Ring signal to w ake up the system.
Resume by RTC Alarm
When Enabled, the system uses the R TC to gener ate a w akeup event.
Wakeup Event After G3
This field is used to enable or disable the specific w akeup event after G3. It needs to
switch the hardw are jumper (f or AC power on) to the proper set ting.
31
Chapter 3 BIOS Setup
www.df .com
Chapter 3
CPU Configuration
SATA Configuration
This section is used to configure the CPU . It will also displa y the detected CPU inf ormation.
This section is used to configure the f unctions of Serial A TA devices.

Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Core(TM) i3-4340TE CPU @ 2.60GHz
CPU Signature
306c3
Processor Family
6
Microcode Patch
1c
FSB Speed
100 MHz
Max CPU Speed
2600 MHz
Min CPU Speed
800 MHz
CPU Speed
2600 MHz
Processor Cores
2
Intel HT Technology
Supported
Intel VT-X Technology
Supported
Intel SMX Technology
Not Supported
64-bit
Supported
EIST Technology
Supported
CPU C3 State
Supported
CPU C6 State
Supported
CPU C7 State
Supported
L1
L1
L2
L3
Data Cache
Code Cache
Cache
Cache
SATA Controller(s)
SATA Mode Selection
[Enabled]
[IDE]
Serial ATA Port 0
Software Preserve
Serial ATA Port 1
Software Preserve
Serial ATA Port 4
Software Preserve
Serial ATA Port 5
Software Preserve
Empty
Unknown
Empty
Unknown
Empty
Unknown
Empty
Unknown
Enable or disable SATA
Device.


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
SATA Controller(s)

[Enabled]
[All]
[Enabled]
[Enabled]
Enabled for Windows XP
and Linux (OS optimized
for Hyper-Threading
Technology) and Disabled
for other OS (OS not
optimized for
Hyper-Threading
Technology). When
Disabled only one thread
per enabled core is
enabled.


32 KB x 2
32 KB x 2
256 KB x 2
4096 KB
Hyper-threading
Active Processor Cores
Intel Virtualization Technology
EIST
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
This field is used to enable or disable the Serial A TA devices.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
SATA Mode Selection
Hyper-threading
The mode selection determines how the S ATA controller(s) oper ates.
Enables this field f or Windows XP and Linux which are optimized f or Hyper-Threading
technology. Select disabled f or other OSes not optimized f or Hyper-Threading technology. When disabled, only one thread per enabled core is enabled.
IDE Mode
This option configures the Serial A TA drives as P arallel ATA storage devices.
AHCI Mode
This option allows the Serial A TA devices to use AHCI (Adv anced Host Controller Inter face).
Active Processor Cores
Number of cores to enable in each processor package.
Intel Virtualization Technology
When this field is set to Enabled, the VMM can utilize the additional hardw are capabilities provided by Vanderpool Technology.
EIST
This field is used to enable or disable the Intel Enhanced SpeedStep T echnology.
32
Chapter 3 BIOS Setup
www.df .com
Chapter 3
When IDE mode is selected in the S ATA Mode Selection, it will displa y the f ollowing
information:
SATA Controller Speed
Indicates the maximum speed that the Serial A TA controller can support.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
SATA Controller(s)
SATA Mode Selection
[Enabled]
[IDE]
Serial ATA Port 0
Software Preserve
Serial ATA Port 1
Software Preserve
Serial ATA Port 4
Software Preserve
Serial ATA Port 5
Software Preserve
Empty
Unknown
Empty
Unknown
Empty
Unknown
Empty
Unknown
Port 0, Port 1, Port 4 and Port 5
Determines how SATA
controller(s) operate.
Enables or disables these Serial A TA ports.
Hot Plug
Designates the serial ATA port as hot pluggable.


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
When AHCI mode is selected in the S ATA Mode Selection, it will displa y the f ollowing
information:
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
SATA Controller(s)
SATA Mode Selection
SATA Controller Speed
[Enabled]
[AHCI]
[Default]
Serial ATA Port 0
Software Preserve
Port 0
Hot Plug
Serial ATA Port 1
Software Preserve
Port 1
Hot Plug
Serial ATA Port 4
Software Preserve
Port 4
Hot Plug
Serial ATA Port 5
Software Preserve
Port 5
Hot Plug
Empty
Unknown
[Enabled]
[Disabled]
Empty
Unknown
[Enabled]
[Disabled]
Empty
Unknown
[Enabled]
[Disabled]
Empty
Unknown
[Enabled]
[Disabled]
Determines how SATA
controller(s) operate.


Enter:
+/-:
F1:
F2:
F3:
F4:
ESC:
Select Screen
Select Item
Select
Change Opt.
General Help
Previous Values
Optimized Defaults
Save and Reset
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
33
Chapter 3 BIOS Setup
www.df .com
Chapter 3
PCH-FW Configuration
USB Configuration
This section is used to configure the par ameters of Management Engine T echnology.
This section is used to configure the par ameters of the USB device.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
ME FW Version
ME Firmware Mode
ME Firmware Type
ME Firmware SKU

Firmware Update Configuration
9.1.2.1010
Normal Mode
Full Sku Firmware
1.5MB
Configure Management
Engine Technology
Parameters
USB Configuration
USB Module Version
8.10.27
USB Devices:
1 Keyboard, 1 Mouse, 2 Hubs
Legacy USB Support
USB3.0 Support
XHCI Hand-off
EHCI Hand-off
[Enabled]
[Enabled]
[Enabled]
[Disabled]


Enables Legacy USB
support. AUTO option
disables legacy support if
no USB devices are
connected. DISABLE
option will keep USB
devices available only for
EFI applications.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Firmware Update Configuration
Legacy USB Support
Enables or disables the Me FW Image R e-Flash function.
Enabled
Enables legacy USB .
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Me FW Image Re-Flash
[Disabled]
Auto
Disables support f or legacy when no USB devices are connected.
Enable/Disable Me FW
Image Re-Flash function.
Disabled
Keeps USB devices a vailable only f or EFI applications.
USB3.0 Support
Enable or disable the support of the USB 3.0 (XHCI) controller .


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
XHCI Hand-off
This is a workaround f or OSes without the support of XHCI hand-of f. The change of
XHCI ownership should be claimed by the XHCI driv er.
EHCI Hand-off
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
This is a workaround f or OSes without the support of EHCI hand-of f. The change of
EHCI ownership should be claimed by the EHCI driv er.
34
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Super IO Configuration
Serial Port 5 Configuration to Serial Port 10 Configuration
This section is used to configure the I/O f unctions supported by the onboard Super I/O chip .
Sets parameters of serial port 5 (COM E) to serial port 10 (COM J).
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced

Serial Port 5 Configuration
Restore AC Power Loss
Help.
Super IO Configuration
Super IO Chip
NCT6106D
Restore AC Power Loss
[Power Off]
WatchDog Timer Unit
Super IO Watchdog Timer
[Second]
0
Serial Port
Device Settings
[Enabled]
IO=3F8h; IRQ=4;
Change Settings
[Auto]
Enable or Disable Serial
Port (COM)

Serial
Port 5 Configuration
Port 6 Configuration
Port 7 Configuration
Port 8 Configuration

Serial Port 9 Configuration

Serial Port 10 Configuration

Parallel Port Configuration

Serial

Serial

Serial


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Restore AC Power Loss
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Power Off
Serial Port 6 Configuration
When power returns after an AC power failure, the system’s power is off. You must
Serial Port
Device Settings
[Enabled]
IO=2F8h; IRQ=3;
Change Settings
[Auto]
press the P ower button to power -on the system.
Enable or Disable Serial
Port (COM)
Power On
When power returns after an AC power f ailure, the system will automatically power -on.


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Last State
When power returns after an AC power f ailure, the system will return to the state
where you left of f before power f ailure occurs. If the system’ s power is of f when AC
power failure occurs, it will remain of f when power returns. If the system’ s power is on
when AC power f ailure occurs, the system will power -on when power returns.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Watchdog Timer Unit
Selects the w atchdog timer unit: second or minute.
Super IO Watchdog Timer
Sets the timeout v alue of the super IO w atchdog timer. 0 means disabled.
35
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 7 Configuration
Serial Port
Device Settings
[Enabled]
IO=3E8h; IRQ=7;
Change Settings
[Auto]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 9 Configuration
Enable or Disable Serial
Port (COM)
Serial Port
Device Settings
[Enabled]
IO=2E0h; IRQ=10;
Change Settings
[Auto]
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
Enable or Disable Serial
Port (COM)


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 8 Configuration
Serial Port
Device Settings
[Enabled]
IO=2E8h; IRQ=7;
Change Settings
[Auto]
Serial Port 10 Configuration
Enable or Disable Serial
Port (COM)
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
Serial Port
Device Settings
[Enabled]
IO=2F0h; IRQ=10;
Change Settings
[Auto]
RS485 Auto Flow
[Disabled]
Enable or Disable Serial
Port (COM)


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
36
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Serial Port
PC Health Status
Enables or disables these serial ports (COM).
This section displa ys the hardw are health monitor.
Change Settings
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Selects the IO/IRQ set tings for the super I/O device.
RS485 Auto Flow
Enables or disables the serial port 10 RS485 auto flow .
Parallel Port Configuration
Sets parameters of P arallel port (LPT/LPE).
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Parallel Port Configuration
Parallel Port
[Enabled]
Change Settings
Device Mode
[Auto]
[STD Printer Mode]
Smart Fan Function
Setting
PC Health Status

Smart
Fan Function
Case Open
[Disabled]
CPU Temperature
System Temperature
CPU Fan Speed
System Fan Speed
VCore
+5V
+12V
+1.5V
+3.3V
3VSB
VBAT
: +26.5 C
: +32.0 C
: 4411 RPM
: N/A
: +1.744 V
: +5.077 V
: +12.232 V
: +1.504 V
: +3.392 V
: +3.392 V
: +3.072 V
Enable or Disable Parallel
Port (LPT/LPTE).


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Smart Fan Function
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
Smart Fan Function
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Parallel Port
Enables or disables the par allel port (LPT/LPTE).
Change Settings
Selects the IO set ting for the super I/O device.
Device Mode.
Enable CPU Smart Fan
CPU Smart Fan Control
Boundary 4
Boundary 3
Boundary 2
Boundary 1
Speed Count 5
Speed Count 4
Speed Count 3
Speed Count 2
Speed Count 1
[Enabled]
60
50
40
30
100
75
50
40
30
System Smart Fan Control
Boundary 3
Boundary 2
Boundary 1
Speed Count 5
Speed Count 4
Speed Count 3
Speed Count 2
Speed Count 1
[Enabled]
60
50
40
30
100
75
50
40
30


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Selects the mode f or the printer port.
37
Chapter 3 BIOS Setup
www.df .com
Chapter 3
CPU Smart Fan Control
Second Super IO Configuration
When this f eature is set to Automatic, the CPU’ s fan speed will rotate according to the
CPU’s temperature. The higher the temper ature, the f aster the speed of rotation.
This section is used to configure the par ameters of the system second super I/O chip .
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
System Smart Fan Control
When this f eature is set to Automatic, the S ystem’s fan speed will rotate according to
the System’s temperature. The higher the temper ature, the f aster the speed of rotation.
Set Parameters of Serial
Port 1 (COMA).
Second Super IO Configuration
Second Super IO Chip

Serial Port 1 Configuration

Serial Port 2 Configuration

Serial Port 3 Configuration

Serial Port 4 Configuration
Boundary 1 to Boundary 4
NCT5104D
The range is 0-127.
Speed Count 1 to Speed Count 5
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
The range is 1-100%.
Case Open
Sets this field to Enabled to allow the system to alert y ou of a chassis intrusion ev ent.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Serial Port 1 Configuration to Serial Port 4 Configuration
Sets the par ameters of serial port 1 (COM A) to serial port 4 (COM D).
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 1 Configuration
Serial Port
Device Settings
[Enabled]
IO=240h; IRQ=5;
Change Settings
[Auto]
Enable or Disable Serial
Port (COM)
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
38
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 2 Configuration
Serial Port
Device Settings
[Enabled]
IO=248h; IRQ=5;
Change Settings
[Auto]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 4 Configuration
Enable or Disable Serial
Port (COM)
Serial Port
Device Settings
[Enabled]
IO=258h; IRQ=5;
Change Settings
[Auto]
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
Enable or Disable Serial
Port (COM)
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Serial Port
Enables or disables these serial ports (COM).
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port 3 Configuration
Serial Port
Device Settings
[Enabled]
IO=250h; IRQ=5;
Change Settings
[Auto]
Change Settings
Enable or Disable Serial
Port (COM)
Selects the IO/IRQ set tings for the super I/O device.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4:
Save and Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
39
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Network Stack
Ipv4 PXE Support
This section is used to enable or disable UEFI network stack.
When enabled, Ipv4 PXE boot supports. When disabled, Ipv4 PXE boot option will not
be created.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
[Disabled]
Network Stack
Ipv6 PXE Support
When enabled, Ipv6 PXE boot supports. When disabled, Ipv6 PXE boot option will not
be created.
Enable/Disable UEFI
network stack.


Enter:
+/-:
F1:
F2:
F3:
F4:
ESC:
Select Screen
Select Item
Select
Change Opt.
General Help
Previous Values
Optimized Defaults
Save and Reset
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
When Network Stack is enabled, it will displa y the f ollowing information:
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Network Stack
Ipv4 PXE Support
Ipv6 PXE Support
[Enabled]
[Enabled]
[Enabled]
Enable/Disable UEFI
network stack.


Enter:
+/-:
F1:
F2:
F3:
F4:
ESC:
Select Screen
Select Item
Select
Change Opt.
General Help
Previous Values
Optimized Defaults
Save and Reset
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
40
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Chipset
System Agent (SA) Configuration
This section is used to configure the par ameters of S ystem Agent.
This section configures relev ant chipset f unctions.
System
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Advanced
Chipset
Boot
Security
Save & Exit
Main
Agent (SA) Configuration
Configuration
PCH-IO
System Agent (SA)
Parameters
System Agent Bridge Name
System Agent RC Version
VT-d Capability
Graphics
NB PCIe
Memory
Haswell
1.5.0.0
Unsupported
Config graphics settings.
Configuration
Configuration
Configuration




Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save and Reset
ESC: Exit
Enter:
+/-:
F1:
F2:
F3:
F4:
ESC:
Select Screen
Select Item
Select
Change Opt.
General Help
Previous Values
Optimized Defaults
Save and Reset
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
41
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Graphics Configuration
DVMT Pre-Allocated
This field configures the gr aphics settings.
Selects DVMT 5.0 Pre- Allocated (Fixed) Graphics Memory size used by the Internal
Gr aphics Device. Please ref er to the screen shown below .
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Graphics Configuration
IGFX VBIOS Version
IGfx Frequency

Primary Display
Internal Graphics
DVMT Pre-Allocated
DVMT Total Gfx Mem
LCD Control
2171
700 MHz
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Select which of IGFX/
PEG/PCI Graphics
device should be Primary
Display.
Graphics Configuration
IGFX VBIOS Version
IGfx Frequency
[Auto]
[Auto]
[32M]
[256M]



Enter:
+/-:
F1:
F2:
F3:
F4:
ESC:
Primary Display
Internal Graphics
DVMT Pre-Allocated
DVMT Total Gfx Mem
LCD Control
Select Screen
Select Item
Select
Change Opt.
General Help
Previous Values
Optimized Defaults
Save and Reset
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
2171
700 MHz
DVMT Pre-Allocated
32M
64M
96M
128M
160M
192M
224M
256M
288M
320M
352M
384M
416M
448M
480M
512M
1024M
Select DVMT5.0 PreAllocated (Fixed) Graphics Memory size used
by the Internal Graphics
Device.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Primary Display
DVMT Total Gfx Mem
Auto When the system boots, it will auto detects the displa y device.
IGFX When the system boots, it will first initialize the onboard VGA.
PEG When the system boots, it will first initialize the PCI Express x16 gr aphics card.
Selects DVMT 5.0 total gr aphics memory size used by the internal gr aphics device.
Please ref er to the screen shown below .
Internal Graphics
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Keeps IGD enabled based on the setup options .
Graphics Configuration
IGFX VBIOS Version
IGfx Frequency

Primary Display
Internal Graphics
DVMT Pre-Allocated
DVMT Total Gfx Mem
LCD Control
2171
700 MHz
Select DVMT5.0 Total
Graphics Memory size
used by the Internal
Graphics Device.
[Auto]
[Auto
[32M]]
[256M]
DVMT Total Gfx Mem
128M
256M
MAX
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
42
Chapter 3 BIOS Setup
www.df .com
Chapter 3
LCD Control
Active LVDS
This field configures the L CD control.
Enable or disable the L VDS unction. When enabled, y ou can select the L CD panel t ype.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
LCD Control
Primary IGFX Boot Display
Active LVDS
[VBIOS Default]
[Disabled]
Primary IGFX Boot Display
Active LVDS
LCD Panel Type
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
When any device is selected in the Primary IGFX Boot Displa y, it will displa y the
following information:
LCD Panel Type
Selects LCD panel used by Internal Gr aphics Device by selecting the appropriate setup
item.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Primary IGFX Boot Display
Secondary IGFX Boot Display
Active LVDS
[CRT]
[None]
[Disabled]
[VBIOS Default]
[Enabled]
[VBIOS Default]
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
LCD Control
Enable/Disable LVDS
Function
LCD Control
Select the Video Device
which will be activated
during POST. This has no
effect if external graphics
present.
Secondary boot display
selection will appear based
on your selection.
VGA modes will be supported only on primary
display.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Select the Video Device
which will be activated
during POST. This has no
effect if external graphics
present.
Secondary boot display
selection will appear based
on your selection.
VGA modes will be supported only on primary
display.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
LCD Control
Primary IGFX Boot Display
Active LVDS
LCD Panel Type
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Secondary IGFX Boot Display
Selects the secondary displa y device.
[VBIOS Default]
[Enabled]
LCD Panel Type
[VBIOS Default]
VBIOS Default
18
Type 1 640x480
18
Type 2 800x600
18
Type 3 1024x768
36
Type 4 1280x1024
Type 5 1400x1050 (108MHz) 36
Type 6 1400x1050 (122MHz) 36
36
Type 7 1600x1200
18
Type 8 1366x768
36
Type 9 1680x1050
36
Type 10 1920x1200
36
Type 11 1440x900
24
Type 12 1024x768
48
Type 13 1280x1024
36
Type 14 1280x800
48
Type 15 1920x1080
48
Type 16 2048x1536
Select LCD panel used by
Internal Graphics Device
by selecting the appropriate setup item.
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
43
Chapter 3 BIOS Setup
www.df .com
Chapter 3
NB PCIe Configuration
Memory Configuration
This field is used to configure the set tings of NB PCI Express.
This field only displa ys the memory configur ation.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
NB PCIe Configuration
PEG0 - Gen X
[Auto]
Enable PEG
[Auto]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Configure PEG0
B0:D1:F0 Gen1-Gen2.
Memory Information
Memory RC Version
Memory Frequency
Total Memory
Memory Voltage
DIMM#1
DIMM#3
CAS Latency (tCL)
Minimum delay time
CAS to RAS (tRCDmin)
Row Precharge (tRPmin)
Active to Precharge (tRASmin)


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit

Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
1.5.0.0
1333 Mhz
2048 MB (DDR3)
1.50V
2048 MB (DDR3)
Not Present
9
9
9
24


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Enable PEG
Enables or disables the PEG.
44
Chapter 3 BIOS Setup
www.df .com
Chapter 3
PCH-IO Configuration
PCI Express Configuration
This section illustr ates the PCH par ameters.
This field is used to configure the PCI Express set tings.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Intel PCH RC Version
Intel PCH SKU Name
Intel PCH Rev ID
1.5.0.0
H81
05/C2
PCIe Port 2 is assigned to USB 3.0
PCIe Port 3 is assigned to LAN.
PCIe Port 4 is assigned to LAN.
PCI Express Root Port 5
PCI Express Root Port 6
PCI Express Configuration
USB Configuration
PCH
Azalia Configuration
Onboard 82574 LAN 2 Controller
Onboard 82574 LAN 1 Controller
Onboard NEC USB 3.0 Controller
High Precision Event Timer Configuration
High Precision Timer
[Enabled]
[Enabled]
[Enabled]
[Enabled]
NEC USB 3.0 Port 3, 4.
PCI Express Configuration
PCI Express Configuration
settings.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Onboard 82574 LAN Controller
PCI Express Root Port 5 and 6
Enables or disables the onboard 82574 L AN controller.
Enables or disables the PCI Express R oot Port 5 and 6.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Onboard NEC USB 3.0 Controller
Enables or disables the USB 3.0 controller .
PCI Express Root Port 5
PCIe Speed
[Enabled]
[Auto]
Control the PCI Express
Root Port.
High Precision Timer
Enables or disables the High Precision Ev ent Timer.


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
PCIe Speed
Selects the speed of PCI Express port: Auto, Gen 1 or Gen 2.
45
Chapter 3 BIOS Setup
www.df .com
Chapter 3
USB Configuration
XHCI Mode
This field is used to configure the USB set tings.
Selects the oper ation mode of XHCI controller . These options are Auto , Enabled,
and Disabled. When Disabled is selected in the XHCI Mode, it will displa y the f ollowing
inf ormation:
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
USB Configuration
USB Precondition
XHCI Mode
[Disabled]
[Auto]
USB Ports Per-Port Disable Control
[Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Precondition work on
USB host controller
and root ports for faster
enumeration.
Mode of operation of
XHCI controller.
USB Configuration
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
USB Precondition
XHCI Mode
[Disabled]
[Disabled]
EHCI1
EHCI2
[Enabled]
[Enabled]
USB Ports Per-Port Disable Control
[Disabled]
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
USB Precondition
EHCI 1 and EHCI 2
Precondition works on USB host controller and root ports f or faster enumeration.
These fields are used to control the f unctions of USB EHCI (USB 2.0) controllers .
One EHCI controller must alw ays be enabled.
46
Chapter 3 BIOS Setup
www.df .com
Chapter 3
USB Ports Per-Port Disable Control
PCH Azalia Configuration
This field is used to control each of the USB ports(0~13) disabling. When enabled,
it will displa y the f ollowing information:
This field is used to configure the PCH Azalia set tings.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Chipset
USB Precondition
XHCI Mode
[Disabled]
[Auto]
USB Ports Per-Port Disable Control
USB Port #0
USB Port #1
USB Port #2
USB Port #3
USB Port #4
USB Port #5
USB Port #9
USB Port #10
USB Port #11
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
USB30
USB30
USB30
USB30
Port
Port
Port
Port
PCH Azalia Configuration
Control each of the USB
ports (0~13) disabling.
USB Configuration
[Enabled]
[Enabled]
[Enabled]
[Enabled]
#0
#1
#2
#3
Azalia
[Auto]
Control detection of the
Azalia device.
Disable= Azalia will be
unconditionally disabled
Enabled= Azalia will be
unconditionally enabled
Auto=Azalia will be enabled if present, disabled
otherwise.
 Select Screen

Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit


Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
USB Port #0/1/2/3/4/5/9/10/11 and USB30 Port #0/1/2/3
Enables or disables these USB ports.
47
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Boot
CSM Parameters
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
1
[On]
Quiet Boot
[Disabled]
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main
Save & Exit
Number of seconds to
wait for setup activation
key.
65535(0xFFFF) means
indefinite waiting.
Advanced
Chipset
Boot
Launch CSM
Boot option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Security
Save & Exit
[Enabled]
[UEFI and Legacy]
[Do not launch]
[Legacy only]
This option controls if
CSM will be launched.
Boot Option Priorities
CSM Parameters




Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Setup Prompt Timeout
Launch CSM
Selects the number of seconds to w ait for the setup activ ation key. 65535(0xFFFF)
denotes indefinite w aiting.
This option controls if CSM will be launched.
Boot option filter
Bootup NumLock State
This option controls what devices system can be boot to .
This allows y ou to determine the def ault state of the numeric k eypad. By def ault, the
system boots up with NumLock on wherein the f unction of the numeric k eypad is the
number keys. When set to Of f, the f unction of the numeric k eypad is the arrow k eys.
Launch PXE OpROM policy
Controls the ex ecution of UEFI and legacy PXE OpROM.
Quiet Boot
Launch Storage OpROM policy
Enables or disables the quiet boot f unction.
Controls the ex ecution of UEFI and legacy stor age OpROM.
48
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Security
Save & Exit
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is only
asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will have
Administrator rights.
The password length must be
in the following range:
Minimum length
3
Maximum length
20
Administrator Password
User Password
Security
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Save & Exit
Main
Set Administrator
Password.
Advanced
Chipset
Boot
Security
Save & Exit
Save Changes and Reset
Discard Changes and Reset
Reset the system after
saving the changes.
Restore Defaults
Boot Override
Launch EFI Shell from filesystem device




Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Reset
ESC: Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Save Changes and Reset
Administrator Password
Sets the administr ator password.
To save the changes, select this field and then press <Enter>. A dialog bo x will appear.
Select Yes to reset the system after sa ving all changes made.
User Password
Discard Changes and Reset
Sets the user password.
To discard the changes, select this field and then press <Enter>. A dialog bo x will appear. Select Yes to reset the system setup without sa ving any changes.
Restore Defaults
To restore and load the optimized def ault values, select this field and then press <Enter>. A dialog bo x will appear. Select Yes to restore the def ault values of all the setup
options.
Launch EFI Shell from filesystem device
Attempts to Launch EFI Shell application (Shellx64 .efi) from one of the a vailable filesystem devices.
49
Chapter 3 BIOS Setup
www.df .com
Chapter 3
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS , you will need the new BIOS file and a flash utilit y, AFUDOS.
EXE. Please contact technical support or y our sales representativ e for the files.
1. The Intel ® Management Engine has already been integr ated into this system board. Due to
the safety concerns, the BIOS (SPI ROM) chip cannot be remo ved from this system board
and used on another system board of the same model.
To execute the utilit y, type:
2. The BIOS (SPI ROM) on this system board must be the original equipment from the f actory
and cannot be used to replace one which has been utilized on other system boards.
A:> AFUDOS BIOS_File_Name /b /p /n
then press <Enter>.
3. If y ou do not f ollow the methods abo ve, the Intel ® Management Engine will not be
updated and will cease to be ef fective.
C:\AFU\AFUDOS>afudos filename /B /P /N
+--------------------------------------------------------------------------------------------------------+
|
|
AMI Firmware Update Utility(APTIO) v2.25
|
Copyright (C)2008 American Megatrends Inc. All Rights Reserved. |
+--------------------------------------------------------------------------------------------------------+
Reading file ..............................
Erasing flash .............................
Writing flash .............................
Verifying flash ..........................
Erasing BootBlock ....................
Writing BootBlock ....................
Verifying BootBlock .................
Note:
a. You can tak e advantage of flash tools to update the def ault configuration of the
BIOS (SPI ROM) to the latest v ersion anytime.
b. When the BIOS IC needs to be replaced, y ou have to populate it properly onto the
system board after the EEPROM progr ammer has been burned and f ollow the
technical person's instructions to confirm that the MAC address should be burned
or not.
done
done
done
done
done
done
done
C:\AFU\AFUDOS>
50
Chapter 3 BIOS Setup
www.df .com
Chapter 4
Chapter 4 - Supported Software
For Windows 7
The CD that came with the system board contains driv ers, utilities and softw are applications
required to enhance the perf ormance of the system board.
Insert the CD into a CD-ROM driv e. The autorun screen (Mainboard Utilit y CD) will appear. If
after inserting the CD , “Autorun” did not automatically start (which is, the Mainboard Utilit y
CD screen did not appear), please go directly to the root directory of the CD and double-click
“Setup”.
For Windows 8
51
Chapter 4 Supported Softw are
www.df .com
Chapter 4
For Windows XP
Microsoft Framework 3.5 (For Windows XP)
Note:
Before installing Microsoft Fr amework 3.5, mak e sure y ou have updated y our
Windows XP oper ating system to Service P ack 3.
To install the driv er, click “Microsoft Fr amework 3.5” on the main menu.
1. Read the license agreement carefully.
Click “I ha ve read and accept
the terms of the License Agree
ment” then click Install.
2. Setup is now installing the
driver.
52
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel Chipset Software Installation Utility
3. Click Exit.
The Intel Chipset Softw are Installation Utilit y is used f or updating Windows ® INF files so that
the Intel chipset can be recognized and configured properly in the system.
To install the utilit y, click “Intel Chipset Softw are Installation Utilit y” on the main menu.
1. Setup is ready to install the
utility. Click Next.
2. Read the license agreement
then click Yes.
53
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Microsoft DirectX 9.0C (For Windows XP)
3. Go through the readme
document for more installation tips then click Next.
To install the utilit y, click “Microsoft DirectX 9.0C Driv er” on the main menu.
1. Click “I accept the
agreement” then click Next.
4. Click Finish to exit setup .
2. To start installation, click
Next.
3. Click Finish. R eboot the
system for DirectX to tak e
effect.
54
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel HD Graphics Drivers (For Windows XP)
4. Setup is now installing the
driver. Click Next to continue.
To install the driv er, click “Intel HD Gr aphics Drivers” on the main menu.
1. To start installation, click
Next.
5. Click “Yes, I w ant to restart
this computer now” then
click Finish.
Restarting the system will allow
the new softw are installation to
take effect.
2. Read the license agreement
then click Yes.
3. Go through the readme
document for system requirements and installation tips then
click Next.
55
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel HD Graphics Drivers (For Windows 7 and Windows 8)
3. Go through the readme
document for system requirements and installation
tips then click Next.
To install the driv er, click “Intel HD Gr aphics Drivers” on the main menu.
1. Setup is now ready to
install the gr aphics driver.
Click Next.
4. Setup is now installing the
driver. Click Next to continue.
By default, the “Automatically run WinS AT and enable the Windows Aero
desktop theme” is enabled. With this enabled, after installing the gr aphics
driver and the system rebooted, the screen will turn blank f or 1 to 2 minutes
(while WinSAT is running) bef ore the Windows Vista desktop appears. The
“blank screen” period is the time Windows is testing the gr aphics performance.
2. Read the license agreement
then click Yes.
5. Click “Yes, I w ant to restart
this computer now” then
click Finish.
Restarting the system will
allow the new softw are
installation to tak e effect.
56
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel Management Engine Drivers
3. Setup is currently installing
the driver. After installation
has completed, click Next.
(For Windows 7 and Windows 8)
To install the driv er, click “Intel Management Engine Driv ers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
4. After completing installation, click Finish.
2. Read the license agreement
then click Yes.
57
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Audio Drivers
Intel LAN Drivers (For Windows XP)
To install the driv er, click “Audio Drivers” on the main menu.
The LAN drivers for Windows XP supporting on the HD332-H81 system board has to be
installed manually. When y ou want to install the L AN driver for Windows XP, please f ollow the
steps below to accomplish the installation.
1. Setup is ready to install the
driver. Click Next.
1. Launch the Hardw are
Update Wizard f or the
selected device. Select
"Update Driver."
2. Click “Yes, I w ant to restart
my computer now” then
click Finish.
Restarting the system will
allow the new softw are
installation to tak e effect.
2. Choose "Install from a list or
specific location (Adv anced)"
and click "Next" to continue
the installation.
58
Chapter 4 Supported Softw are
www.df .com
Chapter 4
3. Choose the option "Don't
search. I will choose the
driver to install" in order to
select the device driv er from
a list, and click "Next."
6. Insert the installation disk
and make sure the selected
drive is correct.
(For 32-bit, the f le name is “e1d5132.inf”.)
4. Select a hardw are type:
DVD/CD-ROM drives. Then,
click "Next."
7. Select the device driv er
y ou want to install f or this
hardw are and then click
"Next."
5. Select y our hardware disk
and then click "Ha ve Disk..."
8. Check the softw are you
are installing, Then, click
"Continue An yway" to start
the installation.
59
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel LAN Drivers (For Windows 7 and Windows 8)
9. Click "Finish" to close the wizard.
To install the driv er, click “Intel L AN Drivers” on the main menu.
1. Setup is ready to install the
driver. Click Next.
10. After completing the installation, the Network adapters
"Intel(R) Ethernet Connection
I217LM" will appear on the
computer management list.
2. Click “I accept the terms
in the license agreement ”
then click “Next ”.
3. Select the progr am featuers
you want installed then
click Next.
60
Chapter 4 Supported Softw are
www.df .com
Chapter 4
DFI Utility
4. Click Install to begin the
installation.
DFI Utility provides information about the board, W atchdog,and DIO. To access the utilit y, click
“DFI Utility” on the main menu.
Note:
If you are using Windows 7 , you need to access the oper ating system as an
administrator to be able to install the utilit y.
1. Setup is ready to instal
the DFI Utilit y driver
Click “Next ”.
5. After completing installation, click Finish.
2. Click “I accept the terms in
the license agreement ” then
click “Next ”.
61
Chapter 4 Supported Softw are
www.df .com
Chapter 4
3. Click “Install” to begin the
installation.
The DFI Utilit y icon will appear on the desktop . Double-click the icon to open the utilit y.
4. After completing installa
tion, click “Finish” .
Information
HW Health
62
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel USB 3.0 Drivers (For Windows 7 Only)
To install the driv er, click “Intel USB 3.0 Driv er” on the main menu.
1. Setup is ready to install the driv er.
Click Next.
HW Health Set
2. Read the license agreement then
click Yes.
WatchDog
63
Chapter 4 Supported Softw are
www.df .com
Chapter 4
RENESAS USB 3.0 Driver
3. Go through the readme document for more installation tips
then click Next.
To install the driv er, click “RENES AS USB 3.0 Driv er” on the main menu.
1. The setup progr am is now ready
to install the utilit y. Click “Next.”
4. Setup is currently installing the
driver. After installation has completed, click Next.
2. Read the license agreement.
Then, click “I accept the terms of
the license agreement.”
Click “Next.”
5. After completing installation, click
Finish.
3. Click “Install” to begin the installation.
64
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Intel Rapid Storage Technology
4. Click “Finish“ to exit the wizard
after the setup progr am is
installed successfully.
(For Windows 7 and Windows 8)
The Intel R apid Storage Technology is a utilit y that allows y ou to monitor the current status
of the S ATA drives. It enables enhanced perf ormance and power management f or the stor age
subsystem.
To install the driv er, click “Intel R apid Storage Technology” on the main menu.
1. Setup is now ready to install
the utility. Click Next.
2. Read the w arning then click
Yes.
65
Chapter 4 Supported Softw are
www.df .com
Chapter 4
3. Read the license agreement then
click Yes.
6. Click “Yes, I w ant to restart m y
computer now” then click Finish.
Restarting the system will allow the
new software installation to tak e
effect.
4. Go through the readme document
for system requirements and installation tips then click Next.
5. Setup is now installing the utilit y.
Click Next to continue.
66
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Nuvton-SIO
4. Installing status.
To install the driv er, click “Nuvton- SIO” on the main menu.
1. The setup progr am is preparing
to install the driv er.
5. Click “Finish“ to exit the wizard
after the installation is completed.
2. The setup progr am is now ready
to install the utilit y. Click Next.
3. Click “Install” to begin the installation.
67
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Infineon TPM Driver and Tool (optional)
4. Enter the necessary inf ormation
and then click Next.
To install the driv er, click “Infineon TPM driv er and tool (option)” on the main menu.
1. The setup progr am is preparing
to install the driv er.
5. Select a setup t ype and then click
Next.
2. The setup progr am is now ready
to install the utilit y. Click Next.
6. Click Install.
3. Click “I accept the terms in the
license agreement” and then
click “Next”.
68
Chapter 4 Supported Softw are
www.df .com
Chapter 4
7. TPM requires installing the Microsoft Visual C++ package prior to
installing the utilit y. Click Install.
10. Click “Yes“ to restart y our system.
8. The setup progr am is currently
installing the Microsoft Visual
C++ package.
9. Click Finish.
69
Chapter 4 Supported Softw are
www.df .com
Chapter 4
Adobe Acrobat Reader 9.3
To install the reader, click “Adobe Acrobat R eader 9.3” on the main menu.
1. Click Next to install or click
Change Destination F older
to select another f older.
2. Click Install to begin installation.
3. Click Finish to exit installation.
70
Chapter 4 Supported Softw are
www.df .com
Chapter 5
Chapter 5 - Digital I/O Programming Guide
The Configuration Register (register 3) configures the direction of the I/O pins. If a bit in this
register is set to 1, the corresponding port pin is enabled as an input with a high-impedence
output driver. If a bit in this register is cleared to 0, the corresponding port is enabled as an
input.
Register Description
The Input P ort Register (register 0) reflects the incoming logic lev els of the pins, regardless of whether the pin if defined as an input or output by the Configur ation Register. They
act only on the red oper ation. Writes to this register ha ve no ef fect. The def ault value (X) is
determined by the externally applied logic lev el. Before a red oper ation, a write tr ansmission
is sent with the command byte to indicate to the I 2C device that the Input P ort Regiser will be
accessed next.
Register 3 (Configur ation Register)
BIT
DEFAULT
C-7
C-6
C-5
C-4
C-3
C-2
C-1
C-0
1
1
1
1
1
1
1
1
Register 0 (Input P ort Register)
BIT
DEFAULT
I-7
I-6
I-5
I-4
I-3
I-2
I-1
I-0
X
X
X
X
X
X
X
X
The Onput P ort Register (register 1) shows the outgoing logic lev els of the pins defined as
outputs by the Configur ation Register. Bit v alues in this register ha ve no ef fect on pins defined
as inputs. In turns, reads from this register reflect the v alue that is in the flip-flop contolling
the output selection, not the actual pin v alue.
Register 1 (Onput P ort Register)
BIT
DEFAULT
O-7
O-6
O-5
O-4
O-3
O-2
O-1
O-0
1
1
1
1
1
1
1
1
The Polarity Inversion Register (register 2) allows polarit y inversion of the pins defined as
inputs by the Configur ation Register. If a bit in this register is set (writ ten with 1), the cor responding port pin’s polarity is in verted. If a bit in this register is clear (writ ten with a 0), the
corresponding port pin’s original polarit y is retained.
Register 2 (P olarity Inversion Register)
BIT
DEFAULT
N-7
N-6
N-5
N-4
N-3
N-2
N-1
N-0
0
0
0
0
0
0
0
0
71
Chapter 5 Digital I/O Progr amming Guide
www.df .com
Chapter 5
Function Description
GPIO Output Process
I2CWriteByte(SlaveAddr, SubAddr, Data):
Write a Byte data to a specified I2C Device.
#def ne
#def ne
#def ne
#def ne
#def ne
I2CReadByte(SlaveAddr, SubAddr, *Data):
Read a Byte data from a specified I2C Device.
SLAVE_ADDR
INPUT_PORT
OUTPUT_PORT
INVERSION_PORT
COMFIG_PORT
0x42
0x00
0x01
0x02
0x03
GpioOut(int PinNum, int Level)
{
BYTE
Data;
BYTE TempPinNum = PinNum%8;
SetBit(*Data, Bit) :
Set Data bit n as “1” .
ClrBit(*Data, Bit) :
Set Data bit n as “0” .
//Pin0-7
I2C_ReadByte(SLAVE_ADDR, OUTPUT_PORT, &Data);
if(Level == 0){ClrBit(&Data, TempPinNum);}
else
{SetBit(&Data, TempPinNum);}
I2C_WriteByte(SLAVE_ADDR, OUTPUT_PORT, Data);
GetBit(Data, Bit) :
Return the v alue of data bit n.
return 1;
Sample Code
GPIO Iutput Process
GPIO Configuration
#def ne
#def ne
#def ne
#def ne
#def ne
SLAVE_ADDR
INPUT_PORT
OUTPUT_PORT
INVERSION_PORT
COMFIG_PORT
#def ne
#def ne
#def ne
#def ne
#def ne
0x42
0x00
0x01
0x02
0x03
SLAVE_ADDR
INPUT_PORT
OUTPUT_PORT
INVERSION_PORT
COMFIG_PORT
0x42
0x00
0x01
0x02
0x03
GpioIn(int PinNum, int *Status)
{
BYTE
Data;
BYTE Group = PinNum/8;
BYTE TempPinNum = PinNum%8;
GpioConf g(int PinNum, int Mode)
{
BYTE
Data;
BYTE TempPinNum = PinNum%8;
//Pin0-7 Input/Output Conf guration
I2C_ReadByte(SLAVE_ADDR, CONFIG_PORT, &Data);
if(Mode == 1){SetBit(&Data, TempPinNum);} //Input
else
{ClrBit(&Data, TempPinNum);} //Output
I2C_WriteByte(SLAVE_ADDR, CONFIG_PORT, Data);
//Pin0-7
I2C_ReadByte(SLAVE_ADDR, INPUT_PORT, &Data);
*Status = GetBit(Data, TempPinNum);
return 1;
return 1;
72
Chapter 5 Digital I/O Progr amming Guide
www.df .com
Appendix A
Appendix A - Watchdog Sample Code
;Software programming example:
;--------------------------------------------;(1) Enter Super IO Con f guration mode
;--------------------------------------------MOV
DX,4EH
MOV
AL,87H
OUT
DX,AL
OUT
DX,AL
;------------------------------------------------------------------------------------------;(2) Con f guration Logical Device 8, register CRF0/CRF1 (WD
T Control/WD T
timer)
;------------------------------------------------------------------------------------------MOV DX,4EH
MOV
AL,07H
;Ready to Progr am Logical Device
OUT DX,AL
MOV DX,4FH
MOV
AL,08H
OUT DX,AL
;Select Logical Device 8
MOV DX,4EH
MOV
AL, F1H
OUT DX,AL
;Select watchdog timer register
MOV DX,4FH
MOV
AL,10H
OUT DX,AL
;Set watchdog timer v alue
MOV DX,4EH
MOV
AL, F0H
OUT DX,AL
;Select watchdog Control R egister
MOV DX,4FH
MOV
AL,02H
OUT DX,AL
;Set Watchdog Control Value
;---------------------------------------------------------------;(1) Exit extended f unction mode
;---------------------------------------------------------------MOV
DX,4EH
MOV
AL,AAH
OUT
DX,AL
73
Appendix A Watchdog Sample Code
www.df .com
Appendix B
Appendix B - Troubleshooting Checklist
The picture seems to be constantly moving.
Troubleshooting Checklist
1. The monitor has lost its v ertical sync. Adjust the monitor ’s vertical sync.
This chapter of the manual is designed to help y ou with problems that y ou may encounter
with your personal computer. To efficiently troubleshoot y our system, treat each problem individually. This is to ensure an accur ate diagnosis of the problem in case a problem has multiple
causes.
2. Move away any objects, such as another monitor or f an, that ma y be creating a magnetic
field around the displa y.
3. Make sure y our video card’s output frequencies are supported by this monitor .
Some of the most common things to check when y ou encounter problems while using y our
system are listed below .
The screen seems to be constantly wavering.
1. The power switch of each peripher al device is turned on.
1. If the monitor is close to another monitor , the adjacent monitor ma y need to be turned of f.
Fluorescent lights adjacent to the monitor ma y also cause screen w avering.
2. All cables and power cords are tightly connected.
Power Supply
3. The electrical outlet to which y our peripheral devices are connected is working. T est the
outlet by plugging in a lamp or other electrical device.
When the computer is turned on, nothing happens.
4. The monitor is turned on.
1. Check that one end of the AC power cord is plugged into a liv e outlet and the other end
properly plugged into the back of the system.
5. The display’s brightness and contr ast controls are adjusted properly .
2. Make sure that the v oltage selection switch on the back panel is set f or the correct t ype of
voltage you are using.
6. All add-in boards in the expansion slots are seated securely .
3. The power cord ma y have a “short ” or “open”. Inspect the cord and install a new one if
necessary.
7. Any add-in board y ou have installed is designed f or your system and is set up correctly .
Monitor/Display
Floppy Drive
If the display screen remains dark after the system is turned on:
The computer cannot access the floppy drive.
1. Make sure that the monitor ’s power switch is on.
1. The floppy disk ette may not be f ormatted. Format the disk ette and try again.
2. Check that one end of the monitor ’s power cord is properly at tached to the monitor and
the other end is plugged into a working AC outlet. If necessary , try another outlet.
2. The diskette may be write-protected. Use a disk ette that is not write-protected.
3. Check that the video input cable is properly at tached to the monitor and the system’ s
display adapter.
3. You may be writing to the wrong driv e. Check the path statement to mak e sure y ou are
writing to the targeted driv e.
4. Adjust the brightness of the displa y by turning the monitor ’s brightness control knob .
4. There is not enough space left on the disk ette. Use another disk ette with adequate stor age
space.
74
Appendix B Troubleshooting Checklist
www.df .com
Appendix B
Hard Drive
System Board
Hard disk failure.
1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is
loose, power of f the system, re-install the card and power up the system.
1. Make sure the correct driv e type for the hard disk driv e has been entered in the BIOS .
2. Check the jumper set tings to ensure that the jumpers are properly set.
2. If the system is configured with two hard driv es, make sure the bootable (first) hard driv e
is configured as Master and the second hard driv e is configured as Sla ve. The master hard
drive must ha ve an activ e/bootable partition.
3. Verify that all memory modules are seated securely into the memory sock ets.
4. Make sure the memory modules are in the correct locations.
Excessively long formatting period.
5. If the board f ails to f unction, place the board on a flat surf ace and seat all sock eted components. Gently press each component into the sock et.
If your hard driv e takes an ex cessively long period of time to f ormat, it is lik ely a cable connection problem. Howev er, if y our hard driv e has a large capacit y, it will tak e a longer time to
format.
6. If you made changes to the BIOS set tings, re-enter setup and load the BIOS def aults.
Serial Port
The serial device (modem, printer) doesn’t output anything or is outputting garbled
characters.
1. Make sure that the serial device’ s power is turned on and that the device is on-line.
2. Verify that the device is plugged into the correct serial port on the rear of the computer .
3. Verify that the at tached serial device works by at taching it to a serial port that is working
and configured correctly. If the serial device does not work, either the cable or the serial
device has a problem. If the serial device works, the problem ma y be due to the onboard
I/O or the address set ting.
4. Make sure the COM set tings and I/O address are configured correctly .
Keyboard
Nothing happens when a key on the keyboard was pressed.
1. Make sure the k eyboard is properly connected.
2. Make sure there are no objects resting on the keyboard and that no k eys are pressed dur ing the booting process.
75
Appendix B Troubleshooting Checklist
www.df .com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising