Dfi WM342-KD Manual
WM342-KD330/KD331
Desktop Box PC
User’s Manual
Preliminary
Version
A51400907
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this
document. Further, the manufacturer reserves the right to revise this publication and make
changes to its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.
•
© 2019. All Rights Reserved.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Copyright ���������������������������������������������������������������������� 2
SATA (Serial ATA) Connectors....................................................................... 31
COM (Serial) Ports....................................................................................... 32
USB Ports.................................................................................................... 33
Cooling Fan Connectors............................................................................... 34
Chassis Intrusion Connector ........................................................................ 35
LPC Connector............................................................................................. 36
Power Connectors........................................................................................ 37
SMBus Connector ....................................................................................... 38
Front Panel Connector................................................................................. 39
Expansion Slots........................................................................................... 40
Standby Power LED..................................................................................... 41
Battery........................................................................................................ 41
LAN LED .................................................................................................... 42
Trademarks ������������������������������������������������������������������ 2
FCC and DOC Statement on Class A ���������������������������� 2
About this Manual �������������������������������������������������������� 4
Warranty ��������������������������������������������������������������������� 4
Static Electricity Precautions ��������������������������������������� 4
Safety Measures ����������������������������������������������������������� 4
Chapter 6 - Mounting Options ����������������������������������� 43
Safety Precautions ������������������������������������������������������� 5
Chapter 7 - BIOS Setup ��������������������������������������������� 45
About the Package ������������������������������������������������������� 5
Overview ............................................................................... 45
Insyde BIOS Setup Utility........................................................ 46
Before Using the System ��������������������������������������������� 5
Main........................................................................................................... 46
Advanced ................................................................................................... 46
UEFI Device Manager.................................................................................. 53
Security....................................................................................................... 58
Boot........................................................................................................... 59
Exit............................................................................................................. 60
Chapter 1 - Introduction ���������������������������������������������� 6
Chapter 2 - Getting Started ��������������������������������������� 12
Updating the BIOS.................................................................. 61
Notice: BIOS SPI ROM............................................................ 61
Chapter 3 - Installing Devices ����������������������������������� 13
Chapter 4 - Jumper Settings ������������������������������������ 20
Chapter 8 - Supported Software�������������������������������� 62
Clear CMOS............................................................................ 20
Serial Port RS232/422/485 Select............................................ 21
Serial Port Power Select.......................................................... 23
Mini PCIe/mSATA Signal Select (for KD330-Q170 only)............. 24
Chapter 9 - RAID ������������������������������������������������������ 70
Chapter 10 - Intel AMT Settings ������������������������������� 74
Chapter 5 - Ports and Connectors ���������������������������� 25
Rear Panel I/O Ports............................................................... 25
PS/2 Keyboard/Mouse Port........................................................................... 25
COM (Serial) Ports....................................................................................... 26
Graphics Interfaces...................................................................................... 26
RJ45 LAN Ports............................................................................................ 27
USB Ports.................................................................................................... 27
Audio ......................................................................................................... 28
I/O Connectors....................................................................... 28
Front Audio Connector (for WM342-KD331 only)........................................... 28
S/PDIF Connector........................................................................................ 29
Digital I/O and Power Connector.................................................................. 30
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The auto-run screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
2. Wear an antistatic wrist strap.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 WM342-KD330 or WM342-KD331 System Unit
• 1 CPU cooler
• Danger of explosion if battery incorrectly replaced.
• 1 SATA Data Cable (Length: 650mm)
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• 4 HDD Screws
• 1 PSU Flex ATX 150W/250W/350W/400W/500W (250W Default)
• Keep this system away from humidity.
• 1 System Fan
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
Optional Items
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Power Cord
• 3.5” HDD Tray Kit
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
Before Using the System
• If one of the following occurs, consult a service personnel:
Before powering-on the system, prepare the basic system components.
- The power cord or plug is damaged.
If you are installing the system board in a new system, you will need at least the following
internal components.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
• CPU and Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
- The system is not working properly.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Overview
Key Features
Front View
Model Name
WM342-KD
Processor
6th/7th Generation Intel® CoreTM processors
Chipset
Intel® C236 / Q170 / H110 Chipset
LAN
2 LAN ports (for WM342-KD330)
4 LAN ports (for WM342-KD331)
COM
1 COM port
Displays
1 x VGA
1 x DVI-D (DVI-I connector)
1 x DP++
USB
4 USB 3.0 ports + 2 USB 2.0 ports
Audio
Mic-in and Line-out (for WM342-KD330 only)
Rear View
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
System
Processor
Chipset
6th Generation Intel Core
®
TM
Processors (LGA 1151 Socket)
Intel® Xeon® Processor E3-1275 v5, Quad Core, 8M Cache,
3.6GHz (4.0GHz), 80W (available for KD331-C236 only)
WM342-KD330
KD330-Q170: Intel® Q170 Chipset
KD330-H110: Intel® H110 Chipset
WM342-KD331
KD331-C236: Intel® C236 Chipset
KD331-Q170: Intel® Q170 Chipset
Intel® Xeon® Processor E3-1225 v5, Quad Core, 6M Cache,
3.3GHz (3.7GHz), 80W (available for KD331-C236 only)
Intel® Xeon® Processor E3-1268L v5, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W (available for KD331-C236 only)
Memory
WM342-KD331 (KD331-C236)
Four 288-pin ECC/Non-ECC DIMM up to 64GB, Dual Channel DDR4 2133/2400 MHz
WM342-KD331 (KD331-Q170)
Four 288-pin DIMM up to 64GB, Dual Channel DDR4 2133/2400 MHz
WM342-KD330 (KD330-Q170)
Four 288-pin DIMM up to 64GB, dual channel DDR4 2133/2400 MHz
WM342-KD330 (KD330-H110):
Two 288-pin DIMM up to 32GB, dual channel DDR4 2133/2400 MHz
Controller
Intel® HD Gen 9 Graphics
Feature
OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/
H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Display
1 x VGA
1 x DVI-D (DVI-I connector)
1 x DP++
VGA: resolution up to 1920x1200 @ 60Hz
DVI-D: resolution up to 1920x1200 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
Intel® Core™ i7-6700 Processor, Quad Core, 8M Cache,
3.4GHz (4.0GHz), 65W
Intel® Core™ i7-6700TE Processor, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel® Core™ i5-6500 Processor, Quad Core, 6M Cache,
3.2GHz (3.6GHz), 65W
Graphics
Intel® Core™ i5-6500TE Processor, Quad Core, 6M Cache,
2.3GHz (3.3GHz), 35W
Intel Core™ i3-6100 Processor, Dual Core, 4M Cache, 65W
Intel® Core™ i3-6100TE Processor, Dual Core, 4M Cache,
2.7GHz, 35W
®
Intel® Pentium® Processor G4400, Dual Core, 3M Cache,
3.3GHz, 65W
Intel® Pentium® Processor G4400TE, Dual Core, 3M Cache,
2.9GHz, 35W
Intel® Celeron® Processor G3900, Dual Core, 2M Cache,
2.8GHz, 65W
Triple Display VGA + DVI-D + DP++
Intel® Celeron® Processor G3900TE, Dual Core, 2M Cache,
2.6GHz, 35W
7th Generation Intel® CoreTM Processors (LGA 1151 Socket)
Intel® Xeon® E3-1275 v6, Quad Core, 8M Cache, 3.8GHz (4.2GHz),
80W (available for KD331-C236 only)
Intel® Core™ i7-7700 Processor, Quad Core, 8M Cache, 3.6GHz
(4.2GHz), 65W
Intel® Core™ i5-7500 Processor, Quad Core, 6M Cache, 3.4GHz
(3.8GHz), 65W
Intel® Core™ i3-7101E Processor, Dual Core, 3M Cache, 3.9GHz , 65W ECC
memory Supported)
Storage
External
1 or 2 x 2.5" SATA 3.0 Drive Bays (1 x 2.5" SATA drive bay by
default)
Expansion
Interface
WM342-KD330
1 x PCIe x16 (Gen 3)
1 x PCI
1 x Full-size Mini PCIe (USB/PCIe/mSATA, PCIe by default) (only for
KD330-Q170 with the Intel® Q170 Chipset)
Additional internal slot without external access from the chassis slot:
PCIe x4
WM342-KD331
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
1 x M.2 Key M (2260/2280) (Intel® Optane™ memory support only
for KD331-C236 with the Intel® C236 Chipset)
Additional internal slot without external access from the chassis slot:
PCIe x8
PCIe x4
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Audio
Codec
Realtek ALC888S-VD2-GR
ETHERNET
Controller
WM342-KD330
Environment
KD330-Q170:
1 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps)*
Standards &
Certifications
KD330-H110:
1 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219V PCIe (10/100/1000Mbps)
WM342-KD331
3 x Intel® I211AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps)*
Mechanism
Operating
Temperature
0 to 45°C
Storage
Temperature
0 to 60°C
Relative
Humidity
5 to 95% RH (non-condensing)
Shock
Operating: 3G
Non-operating: 5G
Vibration
Operating: Random 5~500Hz 0.5G
Non-operating: Sine 10~500Hz 1.5G
Package
Drop
ISTA Project 1A
Construction
Sheet Metal
Wall Mount
LED
Indicators
1 x Power LED
1 x HDD LED
Mounting
Dimensions
306.6 mm x 132.1 mm x 301.9 mm
REAR I/O
Ethernet
WM342-KD330
2 x GbE (RJ-45)
Weight
TBD
Note: *SKUs with the Intel® H110 chipset or the Intel® Core™ i3, Celeron® and Pentium®
processors do not support iAMT.
WM342-KD331
4 x GbE (RJ-45)
Serial
1 x RS-232/422/485 (RS-232 w/ power) (DB-9 connector)
USB
4 x USB 3.0
2 x USB 2.0
PS/2
1 x PS/2 (mini-DIN-6)
Display
1 x VGA
1 x DVI-D (DVI-I connector)
1 x DP++
Audio
1 x Line-out, 1 x Mic-in (WM342-KD330 only)
Buttons
1 x Power Button, 1 x Reset Button
Cooling
Fan
1 x System Fan
WatchDog
Timer
Output &
Interval
System Reset, Programmable via Software from 1 to 255
Seconds
Power
Supply
Flex ATX 250W (or optional 150/350/400/500W)
OS Support
and BIOS
OS
Windows 10 IoT Enterprise 64-bit
BIOS
Insyde SPI 128Mbit
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the WM342-KD
DVI-D (DVI-I connector)/DP++/VGA Port
Connects the DVI-D (DVI-I signal)/DP++/VGA connector of an LCD monitor.
Front View
COM Port
Connects serial devices. COM 1 can be selected among RS232, RS422 and RS485 as well as
between RS232 and RS232 with power via jumper settings.
USB 3.0 Ports
Connect USB 3.0 devices and devices based on USB 2.0 and 1.1/1.0 versions.
USB 2.0 Ports
Connect USB 2.0 devices and devices based on USB 1.1/1.0 versions.
LAN Ports
Connect the system to a local area network. Note that the model with the KD330 mainboard
has only two ports whereas the model with the KD331 mainboard has four ports.
Line-out/Mic-in (for WM342-KD330 only)
Connects an external speaker and microphone.
PS/2 KB/Mouse
Connects a PS/2 keyboard and mouse.
WM342-KD331
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
Rear View
Expansion Slots
Provides PCIe or PCI expansion connectivity. Note that the model with the KD330 mainboard
has one PCIe and one PCI expansion slots whereas the model with the KD331 mainboard has
two PCIe expansion slots.
Expansion
Slots
Power Button
Power Button
Press to power on or off the system.
Status LED (green)
HDD LED (red)
Status LED (Green)
LAN Ports
Indicates system status.
Status LED
ACPI state
S0
Sleep
S4, S5
LED Behavior
ON
Blinking
Off
HDD LED (Red)
Indicates the status of hard drives.
SATA
Drive Bay
COM
VGA
HDD LED
USB 3.0 Ports
DVI-D
DP++
PS/2 Keyboard/Mouse
LAN 3 & LAN 4 (KD331)
USB 2.0 Ports
or
Line-out & Mic-in (KD330)
HDD State
Disk access
activity
LED Behavior
Blinking
Disk drives present or not present
Off
SATA Drive Bay
Inserts a SATA drive.
9
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions (WM342-KD330)
Mechanical Dimensions (WM342-KD331)
Left View
322.00
Right View
Left View
306.60
Right View
132.10
132.10
306.60
59.30
12.10
188.00
301.90
59.30
301.90
322.00
188.00
Rear View
12.10
Rear View
Front View
Front View
10
Chapter 1 Introduction
www.dfi.com
Chapter 1
Motherboard Dimensions (KD330-Q170/KD330-H110)
Motherboard Dimensions (KD331-C236/KD331-Q170)
209.55
198.98
173.73
165.82
135.39
105.13
90.81
84.63
47.29
26.97
0.00
209.55
165.82
90.81
47.29
45.72
26.97
6.65
0.00
34.29
29.22
10.16
0.00
10.16
0.00
22.86
22.86
46.94
46.94
154.94
75.29
75.29
94.79
94.79
130.79
130.79
150.29
154.94
150.29
154.94
154.94
205.33
227.33
233.68
203.20
45.72
20.32
203.20
180.23
227.33
45.72
20.32
160.23
227.33
233.68
11
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
•
SATA HDD/SSD
M.2 card
PCIe cards
CPU
Installing Devices
The following devices can be installed in the system:
•
•
•
DIMM
Mini PCIe card
M.2 card
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1.
2.
Power on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing an Operating System
Depending on the method you choose to install your system, you may use a USB flash drive
or install a CD-ROM drive to run the Operating System CD.
Make sure that a SATA drive or an M.2 card is already installed.
1.
2.
Refer to the following chapters for information on installing a SATA drive or an M.2 card.
Refer to your operating system manual for instructions on installing an operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to provide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
12
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing Devices
Opening the Chassis
Installing a DIMM
Please observe the following guidelines and follow the procedure to open the system.
The system is equipped with four DIMM sockets. Please use the following procedure to install a
DIMM into the socket.
1.
Make sure the system and all other peripheral devices connected to it have been powered off.
2.
Disconnect all power cords and cables.
3.
Remove the top cover by uninstalling the thumb screws.
1.
Align the notch on the DIMM with the tab in the DIMM connector.
2.
Press down on the DIMM until the release tabs spring back to secure the DIMM in place.
Thumb screw
The installed DIMM
Notes:
1.
The system is equipped with four DDR4 (dual channel) sockets. To enable dualchannel, populate DIMM sockets that belong to the same channel:
Channel A: DDR4_1 & DDR4_3
Channel B: DDR4_2 & DDR4_4
2.
The DIMM sockets can only accommodate DDR4 memory modules. Please do not
install other types of memory modules.
3.
The WM342-KD330 (with the Intel® H110 Chipset) is equipped with only two
DIMM sockets.
13
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a PCI or PCIe Expansion Card
3.
Use the following procedure to install an expansion card:
1. Remove the mounting screws to uninstall the card slot bracket.
Reinstall the card slot bracket to secure the expansion card in place.
Rear View
Card slot bracket
PCIe card
Screw
2.
Insert the expansion card in the connector on the motherboard and press it down until secured.
Notes:
1. The WM342-KD330 chassis slot can accommodate one PCIe x16 and one
PCI slots.
2.
The WM342-KD331 chassis slot can accommodate one PCIe x16 and one
PCIe x4 slots.
PCIe card
14
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a Mini PCIe Card
Installing an M.2 Card
The system board is equipped with one Mini PCIe slot that provides USB, PCI and mSATA interfaces.
The system is equipped with one M.2 socket, supporting both the M.2 22x60mm and 22x80mm
(key M) form factors. Use the following procedure to install an M.2 card:
1.
Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card with
the notch in the connector on the system board.
1.
To install an M.2 type 2260 card, please install the standoff at the 60mm mounting
position first.
Standoff
2.
2.
3.
Push the Mini PCIe card down and use the provided mounting screws to secure the card on
the system board.
Align the notch at the edge of the M.2 card with the key in the connector.
Insert the M.2 card into the connector.
M.2 card
Mounting screw
Note:
The M.2 slot is available in WM342-KD331 (with both Intel® C236 and Q170 chipsets)
and the SKU with Intel® C236 chipset further supports Intel® Optane™ memory.
Note:
The Mini PCIe slot is available in WM342-KD330 (only with Intel® Q170 Chipset).
15
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a 2.5” SATA Drive
The system can accommodate two 2.5" SATA drives. Use the following procedure to install a
SATA drive onto the system.
1.
Remove the thumb screws that secure the HDD drive bay to the chassis and remove the
drive bay.
Mounting screw
3. Slide the HDD drive bay back to the system and secure it with the thumb screws.
4. Connect the SATA data cable and power cable to the connectors on the SATA drive. And connect the other end of the SATA data cable on the motherboard.
Thumb screw
2.
Secure the hard drive to the drive bay. Align the mounting holes on the SATA drive with the
mounting holes on the HDD drive bay. Use 4 mounting screws to install the hard drive onto
the HDD drive bay.
SATA data and
power cable
Drive bay
SATA port
16
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a CPU
5. Remove the protective cap from the CPU socket. The cap is used to protect the CPU socket against dust and harmful particles. Remove the protective cap only to install the CPU.
The system can accommodate a variety of CPUs that are supported by the LGA 1151 socket
and compliant with the power specification. Please refer to the Chapter 1 for the supported
CPU list.
6. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as the photo shown below.
1. Make sure the system and all other peripheral devices connected to it have been poweredoff.
7. Unlock the socket by pushing the load lever down and moving it sideways until it is released from the retention tab and then lift the load lever up.
2. Disconnect all power cords and cables.
3.
The system board is equipped with a surface mount LGA 1151 socket. This socket is exclusively designed for installing a LGA 1151 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1151 socket comes with a protective
cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If
the cap is missing or the cap or contact pins are damaged, contact your dealer immediately.
2. Keep the protective cap. RMA requests will be accepted and processed only if the
LGA 1151 socket comes with the protective cap.
Load lever
Protective
cap
Load plate
Retention tab
8. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as shown below. The CPU’s notch will at the same time fit into
the socket’s alignment key.
Load lever
Protective
cap
4. Unlock the socket by pushing the load lever down, move it sideways until it is released
from the retention tab, and then lift the load lever up.
Alignment key
Gold triangular mark
17
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing the Fan and Heat Sink
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation
across the CPU and heat sink, the CPU will overheat damaging both the CPU and system board.
Note:
A boxed Intel® processor already includes the CPU fan and heat sink assembly.
If your CPU was purchased separately, make sure to only use Intel®-certified fan
and heat sink.
9. Close the load plate and push the load lever down to lock it under the retention tab. While
closing the load plate, slide the front edge of the load plate under the retention tab.
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of the
CPU. The thermal paste is usually supplied when you purchase the fan / heat sink assembly. Do not spread the paste all over the surface. When you later place the heat sink on top
of the CPU, the compound will disperse evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel the
strip that covers the paste before you place the fan / heat sink on top of the CPU.
Retention knob
2. Place the heat sink on top
of the CPU. The 4 screw
around the heat sink,
which are used to secure
the heat sink onto the system board, must match the
4 mounting holes around
the socket.
CPU fan connector
Mounting hole
3. Orient the heat sink such
that the CPU fan’s cable is
nearest the CPU fan connector.
18
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
4. Rotate each screw that are
diagonally across the heat sink.
Perform the same procedure
for the other screws.
Heat sink
“Unlocked” position
of the screw
“Locked” position
of the screw
CPU fan connector
5. Connect the CPU fan’s cable
to the CPU fan connector on
the system board.
19
Chapter 3 Installing Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
Clear CMOS
WM342-KD330
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
COM 1 2
RS232/422/485
Select (JP10) 1
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
1 2 3
1 2 3
1-2 On: Normal
(default)
2-3 On:
Clear CMOS Data
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
ATX
Power
2
Front Panel
11
Intel
I211AT
1
2
JP1
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
1 2 3
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
S/PDIF
1
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
9
iTE
IT8893E
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
10
2
2
5
1
2
10
5
2
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
1
WM342-KD331
1
2
2
COM 3
1
9
5 1
5 1
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
2
COM 4
5
1
9
7
SATA 3
(JP14)
9
COM 2
7
1
6
1
1 9
2
1
SATA 2
1
2
USB 3.0
USB 5-6
DIO
1
SMBus
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
9
If you encounter the following situations, you can reconfigure the system with the default
values stored in the ROM BIOS.
7
SATA 0
5
Buzzer
1
9
1
3
2
2
To load the default values stored in the ROM BIOS, please follow these steps below:
COM 6
COM 5
COM 2 RS232/422/485 Select (JP11)
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
COM 2 RS232/Power Select (JP14)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
5 1
5
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1
3
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper pins back
to its default setting, pins 1 and 2 On.
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM1
VGA
1. Power off the system and unplug the power cord.
System Fan 2
4
CPU Fan
5
+12V
Power
PTN3355
14
Socket LGA1151
2
13
TPM (optional)
1
12
DVI-I (DVI-D signal)
DP++
3. Now plug the power cord and power on the system.
LPC
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
JP1
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
2
Front
Audio
10
6
5
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
11
10
2
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
1
9
1
7
SATA 0
Battery
1
8
DDR4_4
PCIe 1 (PCIe x16)
2
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7
SATA 3
7
1
SATA 4
1 2 3
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
20
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Serial Port RS232/422/485 Select
JP7, JP8, and JP10 (for COM 1) and JP11, JP12, and JP13 (for COM 2) are used to configure
the COM ports to RS232, RS422 (full duplex) or RS485. The pin assignments of the COM ports
will vary according to the jumpers’ settings.
WM342-KD330
COM 1
RS232/422/485
Select (JP7)
2
PS/2 KB/MS
USB 5-6
USB 2.0
1
COM 1 2
RS232/422/485
Select (JP10) 1
IC
6 2
6
5 1
6 2
5
6
5 1
5
COM 1 RS232/Power Select (JP9)
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
JP7,
JP10, JP8
System Fan 1 CPU Fan
5
+12V
Power
LPC
13 TPM (optional)
14
Socket LGA1151
2
DVI-D (DVI-I connector)
DP++
24
1 3 5
1 3 5
1 3 5
1-2 On: RS232
(default)
3-4 On: RS422
Full Duplex
5-6 On: RS485
ATX
Power
JP8 and JP10 (COM 1)
JP12 and JP13 (COM 2)
2 4 6
13
1
1
2 4 6
2 4 6
2 4 6
2
Front Panel
11
1
1 3 5
1-3, 2-4 On: RS232
(default)
2
LAN LED
8
PCIe 1 (PCIe x16 )
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
2
Nuvoton
NCT5104D
(optional)
1
2
9
1
iTE
IT8893E
19
SMBus
2
USB 3.0
USB 5-6
DIO
(for KD330-Q170 only)
1
2
11
10
2
1
USB 2.0
USB 9-10 USB 7-8
1
10
1
2
10
1
6
5
2
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
1
2
COM 2
9
1
2
COM 3
9
5 1
1
2
COM 4
9
7
JP13, JP12, JP11 2 4 6
SATA 3
(JP14)
5 1
COM 1
5
1
2
COM 5
9
12 3 4 5
1 2 3 4 5
6 7 8 9
6 7 8 9
7
SATA 2
1
1 9
2
1
RXD+
RXDTXD+
TXDGND
9
2
COM 9
COM 10
(optional) (optional)
5
7
SATA 1
Nuvoton
NCT6106D
1
2
COM 6
1 3 5
DSR
RTS
CTS
RI
COM 2 RS232/422/485 Select (JP11)
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
COM 2 RS232/Power Select (JP14)
1
3
CTS
DSR
DTR
RXD
RS485
NC.
NC.
GND
TXD+
RXD+
RI
RTS
GND
TXD
DCD
1
2
RS232
6 7 8 9
RS422
Full Duplex
COM 2
RS232
9
10
1 2 3 4 5
N.C.
N.C.
N.C.
N.C.
1
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
7
SATA 0
5
Buzzer
9
1
DCD
RXD
TXD
DTR
GND
S/PDIF
3-5, 4-6 On:
RS422 Full Duplex/ RS485
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
1 3 5
1 3 5
1-3, 2-4 On: RS232
3-5, 4-6 On:
(default)
RS422 Full Duplex/ RS485
DATA+
DATAN.C.
N.C.
GND
3
1
Realtek
ALC888S
1 3 5
N.C.
N.C.
N.C.
N.C.
3
1
7
SPI Flash
BIOS
9
10
1
2
RS422
Full Duplex
NC.
NC.
GND
NC.
DATA+
Clear CMOS
Data (JP1)
9
10
1
2
NC.
NC.
NC.
DATA-
Battery
NC.
NC.
TXDRXD-
Intel
I211AT
Line-out
Mic-in
1
2 4 6
1 3 5
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 2
LAN 1
USB
3-4
USB 3.0
2 4 6
2 4 6
1
12
LAN 1
USB 1-2
USB 3.0
JP7 (COM 1) / JP11 (COM 2)
2 4 6
1
8
PTN3355
3
COM 1 RS232/422/485 Select (JP8)
4
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
RS485
21
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
WM342-KD331
JP7 (COM 1) / JP11 (COM 2)
5
6
5 1
4
5
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1
3
COM 1 RS232/422/485 Select (JP8)
1
8
COM1
VGA
JP7,
JP10, JP8
System Fan 2
4
CPU Fan
1 3 5
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
ATX Power
M.2 M Key
(for KD331-Q170)
11
1
7
DDR4_3
DDR4_2
Intel I211AT
PCIe 2 (PCIe x4)
2
Front
Audio
10
1
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
11
10
2
2
2
2
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
19
JP12 and JP13 (COM 2)
6
6 5
1 3 5
2 1
1-3, 2-4 On: RS232
(default)
7
JP11
1
3
System
Fan 1
Buzzer
1
2
1
COM 1
SATA 3
7
2
3-5, 4-6 On:
RS422 Full Duplex/ RS485
SATA 1
1
SATA 4
5
2 4 6
3-5, 4-6 On:
RS422 Full Duplex/ RS485
2 4 6
7
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
9
1
7
SATA 0
Battery
6
1
8
SATA 3.0
1
2
5-6 On: RS485
DDR4_4
PCIe 1 (PCIe x16)
Intel I211AT
2
LAN LED
DDR4_1
3-4 On: RS422
Full Duplex
1 3 5
JP13, JP12
DCD
RXD
TXD
DTR
GND
M.2 M Key Supports
Optane Memory
(for KD331-C236)
1 3 5
1 3 5
1-3, 2-4 On: RS232
(default)
2
Front Panel
LAN 3-4
1 3 5
13
1
Intel I211AT
1 3 5
JP8 and JP10 (COM 1)
1
USB 3.0
2 4 6
2 4 6
Intel I219LM
USB 3.0
LAN 2
USB 3-4
2 4 6
1-2 On: RS232
(default)
24
Standby
Power LED
LAN 1
USB 1-2
2 4 6
1
12
DVI-I (DVI-D signal)
DP++
2 4 6
6 5
DATA+
DATAN.C.
N.C.
GND
6
5 1
6 2
12 3 4 5
1 2 3 4 5
1 2 3 4 5
6 7 8 9
6 7 8 9
6 7 8 9
N.C.
N.C.
N.C.
N.C.
6 2
1
COM 1 2
RXD+
RXDTXD+
TXDGND
2
N.C.
N.C.
N.C.
N.C.
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
DIO
USB 2.0
DSR
RTS
CTS
RI
2 1
JP7, JP8, and JP10 (for COM1) and JP11, JP12, and JP13 (for COM2) are used to configure the
COM ports to RS232, RS422 (full duplex) or RS485. The pin assignments of the COM ports will
vary according to the jumpers’ settings.
RS422
Full Duplex
RS232
RS485
RS232
1
2
RS422
Full Duplex
NC.
NC.
GND
NC.
DATA+
NC.
NC.
GND
TXD+
RXD+
9
10
9
10
1
2
NC.
NC.
NC.
DATA-
CTS
DSR
DTR
RXD
1
2
NC.
NC.
TXDRXD-
9
10
DCD
RI
RTS
GND
TXD
COM 2
RS485
22
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Serial Port Power Select
5 1
6 2
5
6
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
5
+12V
Power
PTN3355
JP9
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
13 TPM (optional)
2
12 3 4 5
1
12
DVI-D (DVI-I connector)
DP++
24
1
6 7 8 9
13
1
LAN 2
LAN 1
USB
3-4
USB 3.0
9
10
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
1 3 5
LPC
14
Socket LGA1151
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
3
1
7
SPI Flash
BIOS
8
3
1
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
S/PDIF
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
1
6 5
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
9
iTE
IT8893E
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
2
5
1
2
USB 3.0
USB 5-6
DIO
1
SMBus
10
2
COM 2
1
7
SATA 2
6
1
5
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
2
9
1
2
COM 3
5 1
5 1
1
9
2
COM 4
JP9 (COM 1)
2 4 6
1
9
2
2
2 1
1
3
COM 6
COM 5
COM 2 RS232/422/485 Select (JP11)
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
COM 2 RS232/Power Select (JP14)
1 3 5
WM342-KD331
2 4 6
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
1
COM 1 2
RS232/422/485
Select (JP10) 1
6 2
6
5 1
6 2
5
6
5 1
5
1
COM 1 RS232/Power Select (JP9)
3
1 3 5
1
8
5
+12V
Power
PTN3355
14
Socket LGA1151
2
DVI-I (DVI-D signal)
DP++
JP14 (COM 2)
LPC
13
TPM (optional)
1
12
Intel I219LM
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
1
SATA 3.0
1
2
10
1
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
2
5
1
9
1
1
1
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
11
10
2
2
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
Chassis Intrusion
(JP13) (JP12)
1
7
SATA 1
6 5
Intel
COM 2 RS232/Power Select (JP14)
6
7
SATA 0
Battery
Front
Audio
8
DDR4_4
PCIe 2 (PCIe x4)
5
2 1
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
2
7
DDR4_3
PCIe 1 (PCIe x16)
6
5
LAN LED
DDR4_1
DDR4_2
1
1
6
11
Intel I211AT
2
2
Front Panel
M.2 M Key
(for KD331-Q170)
Intel I211AT
2
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
13
1
Intel I211AT
USB 3.0
5
ATX Power
USB 3.0
LAN 2
USB 3-4
6
24
Standby
Power LED
LAN 1
USB 1-2
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
COM1
VGA
1
1 3 5
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
JP9
System Fan 2
4
2 4 6
5
1
9
7
JP14
SATA 3
(JP14)
1
1
1 9
2
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
9
7
SATA 0
5
Buzzer
RS232
RS232
PCIe 1 (PCIe x16 )
Realtek
ALC888S
1
2
CTS
DSR
DTR
RXD
COM 1
VGA
6
DCD
(or 12V)
RXD
TXD
DTR
GND
1
COM 1 2
RS232/422/485
Select (JP10) 1
6 2
DSR
RTS
CTS
RI
(or 5V)
2
2 4 6
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
JP9 (for COM1) and JP14 (for COM2) are used to switch the COM ports to RS232 or RS232
with power. The pin assignments of the COM ports will vary according to the jumper settings.
RI
(or 5V)
RTS
GND
TXD
DCD
(or 12V)
WM342-KD330
19
1
7
RS232/Power Select
SATA 3
7
1
SATA 4
3
JP14
System
Fan 1
RS232 (default)
Buzzer
1
2
DIO
2 1
RS232 with power
JP9 (COM 1)
JP14 (COM 2)
1-3 (RI), 2-4 (DCD) On
3-5 (+5V), 4-6 (+12V) On
USB 2.0
23
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Mini PCIe/mSATA Signal Select (for KD330-Q170 only)
IC
COM 1
RS232/422/485
Select (JP7)
2
PS/2 KB/MS
USB 5-6
USB 2.0
1
COM 1 2
RS232/422/485
Select (JP10) 1
6 2
6
5 1
6 2
5
6
5 1
5
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
1
8
PTN3355
3
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
5
+12V
Power
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
1
13
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Battery
Clear CMOS
Data (JP1)
3
1
7
SPI Flash
BIOS
8
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
Intel
1
S/PDIF
1
9
2
1
2
Nuvoton
NCT5104D
(optional)
1
2
9
1
iTE
IT8893E
(for KD330-Q170 only)
1
2
11
10
2
5
1
2
USB 3.0
USB 5-6
DIO
19
SMBus
USB 2.0
USB 9-10 USB 7-8
1
10
1
2
10
1 9
2
2
COM 2
9
7
1
5
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
2
1
9
2
COM
COM
COM
COM
5 1
5 1
1
9
2
COM 4
2
2
2
2
7
SATA 3
(JP14)
COM 3
JP6
1
SATA 2
6
1
1
7
SATA 1
Nuvoton
NCT6106D
COM 9
COM 10
(optional) (optional)
9
7
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
1
5
Buzzer
5
1
2
COM 5
9
1
2
1
3
COM 6
RS232/422/485 Select (JP11)
RS232/422/485 Select (JP12)
RS232/422/485 Select (JP13)
RS232/Power Select (JP14)
Mini PCIe Socket
1 2 3
JP6 is used to select the signal for the Mini PCIe socket.
Mini PCIe/mSATA Signal Select
JP6
Mini PCIe (default)
1-2 On
mSATA
2-3 On
24
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
Rear Panel I/O Ports
PS/2 Keyboard/Mouse Port
COM 1 DVI-D
LAN 1 LAN 2
PS/2 KB/MS
USB 2.0
VGA
DP++
LAN 4
LAN 3
PS/2 Keyboard/Mouse
USB 3.0
The rear panel I/O consists of the following ports:
These ports are used to connect a PS/2 mouse/keyboard.
•
•
•
•
•
•
•
•
•
Wake-On PS/2 Keyboard/Mouse
One PS/2 Keyboard/Mouse port
One Serial port
One VGA
One DVI-D (DVI-I connector) port
One DisplayPort
Two RJ45 LAN ports (for WM342-KD330) or four RJ45 LAN ports (for WM342-KD331)
Four USB 3.0 ports
Two USB 2.0 ports
Line-out and microphone jack and (for WM342-KD330 only)
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power on the system. To use this function, configure the wake-on function of PS/2
keyboard/mouse in the Advanced menu (“ACPI Configuration” submenu) of the BIOS. Refer to
Chapter 7 for more information.
Note:
This port cannot work with a PS/2 mouse alone. To connect both keyboard and
mouse, please use a PS/2 keyboard mouse splitter cable adapter.
25
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
COM (Serial) Ports
Graphics Interfaces
The display ports consist of the following:
•
•
•
DVI-D (DVI-I connector)
1 DP++ port
1 VGA port
DVI-D
(DVI-I connector)
VGA
COM 1
DP++
COM 1 port
VGA Port
The pin functions of COM 1 will vary according to the respective jumper settings (JP7, JP8 and
JP10). Another jumper (JP9) is used to configure COM 1 to pure RS232 or RS232 with power.
Refer to “Serial Port RS232/422/485 Select” and “Serial Port Power Select” in Chapter 4 for
more information.
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port,
gently tighten the cable screws to hold the connector in place.
DVI-D Port (DVI-I connector)
In addition to the external COM port, the system board is equipped with onboard serial port
pin headers. Refer to “I/O Connectors” in this chapter for more information.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
The DVI-D (DVI-I connector) port is used to connect an LCD monitor. Having a DVI-I connector, this port supports DVI-D signal only. Connect the display device’s cable connector to the
DVI-I port. After plugging the cable connector into the port, gently tighten the cable screws to
hold the connector in place.
BIOS Setting
DP++ Port
Configure the serial ports in the Advanced menu (“SIO NUVOTON6106D” submenu) of the
BIOS. Refer to Chapter 7 for more information.
The DisplayPort is a digital display interface used to connect a display device. The interface,
developed by VESA and backwards compatible with VGA, DVI and HDMI, delivers higher performance than any other digital interfaces.
BIOS Setting
Configure display devices in the advanced menu (“Video Configuration” submenu) of the BIOS.
Refer to Chapter 7 for more information.
26
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
RJ45 LAN Ports
USB Ports
LAN 1
LAN 2
LAN 4
LAN 3
USB 2.0
USB 3.0
USB 3.0
USB 6
USB 5
USB 2
USB 1
USB 4
USB 3
Features
•
LAN 1: Intel® I219LM Gigabit Ethernet controller with iAMT11.0. (Note that Intel® Core™
i3, Celeron® and Pentium® processors and H110 chipset do not support iAMT.)
USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
or
•
LAN 1: Intel® I219V for WM342-KD330 (with the H110 chipset)
•
LAN 2: Intel® I211AT PCI Express Gigabit Ethernet controller
•
LAN 3, LAN4: Intel® I211AT PCI Express Gigabit Ethernet controller for WM342-KD331
(KD331-C236 and KD331-Q170) only
In addition to these external USB ports, the system board is equipped with onboard USB 3.0
and 2.0 pin headers. Refer to “I/O Connectors” in this chapter for more information.
BIOS Setting
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to Chapter 7 for more information.
The LAN ports allow the system board to connect to a local area network with a network hub.
Driver Installation
BIOS Setting
You may need to install the proper drivers in your operating system to use USB devices. Refer
to Chapter 8 and your operating system’s manual or documentation for more information.
Configure the onboard LAN ports in the Advanced menu (“ACPI Configuration” submenu) of
the BIOS. Refer to Chapter 7 for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 8 for more information.
27
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
I/O Connectors
Audio
Front Audio Connector (for WM342-KD331 only)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1
3
1
8
COM1
VGA
System Fan 2
4
CPU Fan
COM 1 RS232/422/485 Select (JP8)
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
Line-out
Mic-in
1
LAN 2
USB 3-4
Intel I211AT
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
2
1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
Mic2-L
Mic2-R
Line2-R
Front_IO_Sense
Line2-L
10
9
2
Front
Audio
10
6
1
5
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
2
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
1
9
1
7
SATA 0
Battery
2
8
DDR4_4
PCIe 1 (PCIe x16)
Front Audio
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
Line2-JD
GND
Presence Signal
Mic2-JD
USB 3.0
13
1
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
Rear Audio (for WM342-KD330 only)
Front Audio
The WM342-KD330 is equipped with 2 audio jacks:
The front audio connector allows you to connect the line-out and mic-in jacks for audio output.
•
Line-out Jack (lime)
This jack is used to connect a headphone or external speakers.
•
Mic-in Jack (pink)
This jack is used to connect an external microphone.
Driver Installation
Install the audio driver. Refer to the chapter 8 for more information.
The WM342-KD331 is equipped with an internal audio connector instead.
Driver Installation
Install the audio driver. Refer to Chapter 8 for more information.
28
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
S/PDIF Connector
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
RS232/422/485
Select (JP10) 1
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
KD330-Q170/H110
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
ATX
Power
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
SPDIF out
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
S/PDIF
1
SATA 0
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
5
SMBus
(for KD330-Q170 only)
1
2
19
5
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
10
2
2
6 2
1
COM 1 2
RS232/422/485
Select (JP10) 1
5 1
6 2
5 1
6
5
6
5
1
COM 1 RS232/Power Select (JP9)
1
7
1
5
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
2
SATA 3
(JP14)
9
1
2
5 1
5 1
1
9
2
COM 4
COM 3
5
1
9
1
9
2
2
1
3
The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis and connect the audio cable to the S/PDIF connector. Make sure pin 1 of
the audio cable is aligned with pin 1 of the S/PDIF connector.
COM 6
COM 5
System Fan 2
4
1
3
CPU Fan
1
8
5
+12V
Power
PTN3355
5
7
COM 1 RS232/422/485 Select (JP8)
4
COM1
VGA
1
SATA 2
6
1
1
1 9
2
COM 2
COM 1
RS232/422/485
Select (JP7)
1
2
USB 3.0
USB 5-6
DIO
1
2
1
iTE
IT8893E
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
PS/2 KB/MS
USB 5-6
USB 2.0
7
1
H110/Q170
PCIe 2 (PCIe x4)
9
NC Ground
SPDIF in
+5V
SATA 3.0
1
5
Buzzer
9
Mini PCIe
(for KD330-Q170 only)
Chassis
1
Intrusion
2
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
KD331-C236/Q170
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
2
10
6
1
5
1
1
5
2
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
9
1
7
SATA 0
Battery
2
8
DDR4_4
PCIe 1 (PCIe x16)
Front
Audio
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
29
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Digital I/O and Power Connector
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
6 2
6
1
COM 1 2
5 1
6 2
5
6
RS232/422/485
Select (JP10) 1
5 1
5
COM 1 RS232/Power Select (JP9)
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
2
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
KD330-Q170/H110
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
1
LAN 2
LAN 1
USB
3-4
USB 3.0
The Digital I/O connector provides monitoring and control function to the connected
devices. We have built support software called EAPI that enables the functionality of
hardware components. Please contact our technical support or sales representatives for the
support software package.
13
1
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
PCIe 1 (PCIe x16 )
Digital I/O Connector
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
S/PDIF
1
9
Nuvoton
NCT5104D
(optional)
1
9
2
2
1
9
2
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
10
2
6 2
6
1
5 1
6 2
5
6
5 1
5
1
COM 1 RS232/Power Select (JP9)
1 9
2
1
1
9
2
2
2
COM 4
COM 3
5 1
7
SATA 3
5
1
9
1
9
1
3
2
2
System Fan 2
4
1
14
Socket LGA1151
2
3
LPC
13
TPM (optional)
24
ATX Power
Standby
Power LED
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
M.2 M Key
(for KD331-Q170)
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
DDR4_2
2
Front
Audio
10
1
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
+12V
5
DIO6
6
GND
7
DIO5
8
+5V
9
DIO4
10
+5V
11
DIO3
12
GND
13
DIO2
14
V_5P0_STBY
15
DIO1
16
V_5P0_STBY
17
DIO0
18
GND
19
GND
20
NC
8
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
9
7
SATA 0
Battery
1
4
SATA 3.0
1
5
DIO7
DDR4_4
PCIe 2 (PCIe x4)
6
2
7
DDR4_3
PCIe 1 (PCIe x16)
1
2
LAN LED
DDR4_1
Intel I211AT
2
3
Front Panel
LAN 3-4
Intel I211AT
+12V
13
1
Intel I211AT
USB 3.0
2
1
12
DVI-D (DVI-I connector)
DP++
KD331-C236/Q170
GND
5
+12V
Power
PTN3355
LAN 1
USB 1-2
Pin Assignment
CPU Fan
1
8
Pins
1
COM 6
COM 5
COM 1 RS232/422/485 Select (JP8)
4
COM1
VGA
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
9
COM 2
COM 1 2
RS232/422/485
Select (JP10) 1
5
2
5 1
Pin Assignment
7
1
6
(JP14)
1
1
1
SATA 2
1
5
SMBus
USB 3.0
USB 5-6
2
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
iTE
IT8893E
DIO
1
2
19
Pins
7
SATA 1
Nuvoton
NCT6106D
COM 9
COM 10
(optional) (optional)
9
7
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
1
2
1
5
Buzzer
Digital I/O
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
30
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
SATA (Serial ATA) Connectors
IC
COM 1
RS232/422/485
Select (JP7)
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
RS232/422/485
Select (JP10) 1
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
1
8
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
5
+12V
Power
PTN3355
13 TPM (optional)
2
1
12
DVI-D (DVI-I connector)
DP++
KD330-Q170/H110
24
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Features
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
PCIe 1 (PCIe x16 )
KD330-Q170/H110:
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
S/PDIF
1
2
9
SMBus
1
5
2
USB 3.0
USB 5-6
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
10
2
1
2
•
4 Serial ATA ports
-Support SATA 3.0 with data transfer rate up to 6Gb/s
•
Support Integrated Advanced Host Controller Interface (AHCI) controller with Intel® Rapid
Storage Technology (RAID mode is only available for KD330-Q170)
10
SATA 1
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
RS232/422/485
Select (JP10) 1
5 1
5
1
COM 1 RS232/Power Select (JP9)
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
(JP14)
2
7
1
2
5 1
5 1
1
9
2
SATA 3
5
1
9
1
9
1
KD331-C236/Q170:
3
2
2
COM 6
COM 5
COM 4
COM 3
7
System Fan 2
4
1
1
8
5
+12V
Power
PTN3355
•
5 Serial ATA ports
-Support SATA 3.0 with data transfer rate up to 6Gb/s
•
Support Integrated Advanced Host Controller Interface (AHCI) controller with Intel® Rapid
Storage Technology
3
CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
COM1
VGA
1
1
5
1
2
7
SATA 2
6
9
1
1 9
2
COM 2
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
iTE
IT8893E
DIO
1
2
1
Nuvoton
NCT6106D
Nuvoton
NCT5104D
(optional)
1
9
2
1
9
7
7
SATA 0
COM 9
COM 10
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
5
Buzzer
7
LPC
14
Socket LGA1151
GND
TXP
TXN
GND
RXN
RXP
GND
PS/2 KB/MS
USB 5-6
USB 2.0
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
The Intel® Rapid Storage Technology supports RAID configuratin of 0, 1, 5 and 10, and with
the Intel® C236 chipset, Intel® Optane™ Technology can be further supported. Please refer to
"Expansion Slots" in this chapter for more information.
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
M.2 M Key Supports
Optane Memory
(for KD331-C236)
1
2
Front
Audio
10
1
1
5
2
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
9
1
7
SATA 0
Battery
5
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
SATA 3.0
1
PCIe 2 (PCIe x4)
6
8
DDR4_4
PCIe 1 (PCIe x16)
1
2
7
DDR4_3
DDR4_2
2
BIOS Setting
11
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
LAN 3-4
KD331-C236/Q170
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the
SATA cable to one of the SATA connectors and the other end to your SATA device.
13
1
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
31
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
1
8
5
+12V
Power
LPC
13 TPM (optional)
14
Socket LGA1151
2
12
DVI-D (DVI-I connector)
DP++
KD330-Q170/H110
6789
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
RS232
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
3
1
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
S/PDIF
1
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
iTE
IT8893E
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
2
5
1
2
USB 3.0
USB 5-6
DIO
1
SMBus
10
2
COM 2
1
7
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1
5
7
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
(JP14)
2
9
1
2
COM 3
5 1
5 1
1
9
COM 4
5
1
9
2
SATA 3
1
9
1
2
2
RS232
1
3
CPU Fan
14
Socket LGA1151
LPC
13
Intel I219LM
USB 3.0
1
13
1
Intel I211AT
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
Connecting External Serial Ports
SATA 3.0
1
2
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
2
1
1
2
PCIe 4 (PCIe x4)
9
1
1
1
Chassis Intrusion
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
COM 2:
RS232/422/485
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
2
COM 3/4/5/6: RS232
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
5
1
Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket
to an available slot at the rear of the system chassis then insert the serial port cable to the
COM connector. Make sure the colored stripe on the ribbon cable aligns with pin 1 of the
COM connector.
7
SATA 1
Intel
1
6
7
SATA 0
Battery
10
8
DDR4_4
PCIe 2 (PCIe x4)
5
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
BIOS Setting
Buzzer
1
2
DIO
USB 2.0
32
Chapter 5 Ports and Connectors
RS485
2
7
DDR4_3
DDR4_2
PCIe 1 (PCIe x16)
1
1
2
LAN LED
DDR4_1
Intel I211AT
Front
Audio
2
Front Panel
M.2 M Key
(for KD331-Q170)
6
9
The pin assignments of COM 1 will vary according to jumper settings (JP7, JP8, and JP10);
the pin assignments of COM 2 will vary according to the jumper settings (JP11, JP12, and
JP13). In addition, JP9 (for COM 1) and JP14 (for COM 2) are used to configure these ports
to pure RS232 or RS232 with power. Refer to “Serial Port RS232/422/485 Select” and “Serial
Port Power Select“ in Chapter 4 for more information.
COM 3 to COM 6 (and the optional COM 7 to 10) are fixed at RS232.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
24
Standby
Power LED
2
RS422
Full Duplex
1
2
COM 2 port
TPM (optional)
ATX Power
VGA
Intel I211AT
RS485
1
12
USB 3.0
RS422
Full Duplex
5
DVI-D (DVI-I connector)
DP++
LAN 2
USB 3-4
6 7 89
Please refer to the “Rear Panel I/O Ports“ section in this chapter for more information.
1
+12V
Power
2
LAN 1
USB 1-2
6789
COM 1 port
System Fan 2
4
9
3
COM 6
COM 5
COM 1 RS232/422/485 Select (JP8)
8
PTN3355
KD331-C236/Q170
1
2
COM 3/4/5/6: RS232
COM1
VGA
COM 1:
RS232/422/485
9
SATA 2
6
1
1
1 9
2
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
9
7
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
9
COM 1
1
5
Buzzer
COM 2:
RS232/422/485
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
CTS
DSR
DTR
RXD
COM 7/8/9/10 (optional):
RS232
12 3 4 5
8
PCIe 1 (PCIe x16 )
Realtek
ALC888S
12 3 4 5
24
ATX
Power
VGA
COM 1:
RS232/422/485
1 2345
1
DSR
RTS
CTS
RI
(or +5V)
PTN3355
DATA+
DATAN.C.
N.C.
N.C.
5
1
N.C.
N.C.
N.C.
N.C.
5 1
3
COM 1 RS232/422/485 Select (JP8)
4
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
System Fan 1 CPU Fan
NC.
NC.
NC.
NC.
DATA+
5
6
NC.
NC.
NC.
DATA-
5 1
6 2
RXD+
RXDTXD+
TXDN.C.
1
COM 1 2
RS232/422/485
Select (JP10) 1
COM 1 RS232/Power Select (JP9)
N.C.
N.C.
N.C.
N.C.
6
NC.
NC.
NC.
TXD+
RXD+
6 2
NC.
NC.
TXDRXD-
2
RI
(or +5V)
RTS
GND
TXD
DCD
(or +12V)
COM 1
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
DCD
(or +12V)
RXD
TXD
DTR
GND
COM (Serial) Ports
Configure the serial ports with more advanced options such as the RS485 auto flow mechanism in the Advanced menu (“Super I/O” submenu) of the BIOS. Refer to Chapter 7 for more
information.
www.dfi.com
Chapter 5
5
6
5 1
5
COM 1 RS232/Power Select (JP9)
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
1
8
USB 6
USB 5
1
COM 1 RS232/422/485 Select (JP8)
4
COM 1
VGA
3
System Fan 1 CPU Fan
5
+12V
Power
PTN3355
13 TPM (optional)
2
USB 2.0
USB 2
USB 1
1
12
DVI-D (DVI-I connector)
DP++
USB 3
USB 3.0
24
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
USB 4
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
20
1
LPC
14
Socket LGA1151
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
PCIe 1 (PCIe x16 )
1
9
10
2
USB 2.0 USB 9-10, 7-8
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
S/PDIF
1
Nuvoton
NCT5104D
(optional)
2
COM 9
COM 10
(optional) (optional)
1
9
9
USB 2.0
USB 9-10 USB 7-8
(for KD330-Q170 only)
1
2
19
11
10
1
10
1
2
10
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
1
9
1
1
9
2
2
5 1
5 1
9
2
1
2
COM 5
COM 4
COM 3
7
SATA 3
1
9
1
KD331-C236/Q170:
•
3
CPU Fan
5
14
2
LPC
13
TPM (optional)
24
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
ATX Power
Standby
Power LED
USB 2
USB 1
USB 4
USB 3
USB 3.0
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
SATA 3.0
1
USB 3.0
PCIe 2 (PCIe x4)
2
6
5
1
USB 9-10 (or optional vertical port), USB 7-8
2
10
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
2
1
9
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
USB 2.0
1
2
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
11
10
2
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
1
2
Realtek ALC888S
9
10
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
5
1
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to Chapter 7 for more information.
7
SATA 1
Intel
1
6
7
SATA 0
Battery
Front
Audio
BIOS Setting
8
DDR4_4
PCIe 1 (PCIe x16)
Intel I211AT
2
LAN LED
DDR4_1
Intel I211AT
1
2
Front Panel
M.2 M Key
(for KD331-Q170)
USB 5-6
11
10
13
1
Intel I211AT
USB 3.0
USB 3.0
The system board is also equipped with internal USB 2.0 and USB 3.0 ports via pin headers.
The 10-pin connector (USB 2.0) allows you to connect 2 additional ports. And the 20-pin connector (USB 3.0) allows you to connect 2 additional ports. These additional USB ports may be
mounted on a card-edge bracket.
Intel I219LM
LAN 2
USB 3-4
C236/Q170: 8 USB 3.0 (4 external ports and 4 via internal pin headers) and 6 (or 5) USB
2.0 (2 external ports and 4 via internal pin headers or 2 via internal pin headers plua 1
vertical port)
1
12
DVI-D (DVI-I connector)
DP++
LAN 1
USB 1-2
Q170: 6 USB 3.0 (4 external ports and 2 via internal pin headers) and 6 USB 2.0 (2
external ports and 4 via internal pin headers)
3
2
COM 6
System Fan 2
4
Socket LGA1151
•
1
1
+12V
Power
PTN3355
H110: 4 USB 3.0 (all external ports) and 6 USB 2.0 (2 external ports and 4 via internal pin
headers)
5
COM 1 RS232/422/485 Select (JP8)
8
COM1
VGA
5
2
1
2
9
10
•
7
1
6
(JP14)
1
1 9
2
1
SATA 2
1
COM 2
COM 1
RS232/422/485
Select (JP7)
USB 5
USB 2.0
5
2
2
PS/2 KB/MS
USB 5-6
USB 2.0
USB 6
SMBus
USB 3.0
USB 5-6
DIO
1
2
KD331-C236/Q170
iTE
IT8893E
7
SATA 1
Nuvoton
NCT6106D
1
9
2
1
H110/Q170
PCIe 2 (PCIe x4)
4
7
SATA 0
COM 8
COM 7
(optional) (optional)
9
1
1
USB 2.0
KD330-Q170/H110:
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
5
Buzzer
11
1
10
USB 3.0 USB 5-6
(for KD330-Q170 only)
Optional USB 2.0 vertical port
(for KD331-C236/Q170)
Key
GND
+Data
-Data
VCC
5 1
6 2
USB 3.0
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
6
N. C.
GND
+Data
-Data
VCC
1
COM 1 2
RS232/422/485
Select (JP10) 1
6 2
D+
DGND
TX+
TXGND
RX+
RXPWR
2
VCC
DataData+
GND
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
Over Current Protection
D+
DGND
TX+
TXGND
RX+
RXPWR
USB Ports
KD330-Q170/H110
19
1
7
SATA 3
7
Driver Installation
1
SATA 4
3
System
Fan 1
You may need to install proper drivers in your OS to use USB devices. Refer to Chapter 8 and
your operating system’s documentation for more information.
Buzzer
1
2
DIO
USB 2.0
33
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Cooling Fan Connectors
KD330-Q170/H110
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
5 1
5
COM 1 2
RS232/422/485
Select (JP10) 1
COM 1 RS232/Power Select (JP9)
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
1
8
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
12
CPU fan
24
ATX
Power
1
3
1
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
1
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
1
7
SPI Flash
BIOS
3
System fan 1, 2
4
Ground Speed
Power Control
Sense
13
1
LAN 2
LAN 1
USB
3-4
USB 3.0
System Fan 1
1
DVI-D (DVI-I connector)
DP++
LAN 1
USB 1-2
USB 3.0
4
1
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
4
COM 1
VGA
CPU fan
IC
COM 1
RS232/422/485
Select (JP7)
Ground Sense
Power
8
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
S/PDIF
1
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
9
iTE
IT8893E
SMBus
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
2
1
2
USB 3.0
USB 5-6
DIO
1
5
10
1 9
2
2
6 2
1
COM 1 2
RS232/422/485
Select (JP10) 1
5 1
6 2
5 1
6
5
6
5
5 1
5 1
1
9
2
COM 4
7
SATA 3
5
1
9
1
9
The fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
3
2
2
System Fan 2
1
COM 6
COM 5
CPU fan
1
COM 1 RS232/Power Select (JP9)
1
4
1
System Fan 2
4
BIOS Setting
3
CPU Fan
The Advanced menu (“PC Health Status” submenu) of the BIOS displays the current speed of
the cooling fans. Refer to Chapter 7 for more information.
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM1
VGA
1
COM 3
KD331-C236/Q170
COM 1
RS232/422/485
Select (JP7)
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
2
(JP14)
2
2
7
1
5
9
COM 2
1
SATA 2
6
1
1
3
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
9
1
7
SATA 0
5
Buzzer
PS/2 KB/MS
USB 5-6
USB 2.0
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
System Fan 2
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
1
DDR4_1
7
DDR4_3
DDR4_2
SATA 3.0
1
2
10
6
5
1
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
2
5
1
9
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
USB 2.0
Chapter 5 Ports and Connectors
1
2
USB 3.0
USB 5-6
1
11
10
2
1
2
USB 7-8
7
SATA 2
C236/Q170
Realtek ALC888S
1
1
7
SATA 1
Intel
COM 2 RS232/Power Select (JP14)
6
7
SATA 0
Battery
1
8
DDR4_4
PCIe 2 (PCIe x4)
2
3
2
LAN LED
PCIe 1 (PCIe x16)
Front
Audio
1
11
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7
SATA 3
7
1
SATA 4
System fan 1
1
3
System
Fan 1
Buzzer
1
2
3
DIO
34
www.dfi.com
Chapter 5
Chassis Intrusion Connector
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
5 1
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
1
8
PTN3355
(DDR4_2, DDR4_4 for KD330-Q170 only)
COM 1 RS232/Power Select (JP9)
4
COM 1
VGA
KD330-Q170/H110
IC
5
+12V
Power
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
ATX
Power
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
Ground
Chassis
signal
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
PCIe 1 (PCIe x16 )
1
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
Intel
1
S/PDIF
1
9
2
1
2
Nuvoton
NCT5104D
(optional)
1
2
9
1
iTE
IT8893E
19
SMBus
2
USB 3.0
USB 5-6
DIO
USB 2.0
USB 9-10 USB 7-8
(for KD330-Q170 only)
1
2
11
10
1
2
1
10
2
10
KD331-C236/Q170
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
5
2
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
1
1
9
2
2
7
SATA 3
5
1
9
2
1
9
2
COM 5
COM 4
COM 3
5 1
5 1
1
3
2
COM 6
1
COM 1 RS232/Power Select (JP9)
System Fan 2
4
1
3
The board supports the chassis intrusion detection function. Connect the chassis intrusion
sensor cable from the chassis to this connector. When the system’s power is on and a chassis
intrusion occurs, an alarm will sound. When the system’s power is off and a chassis intrusion
occurs, the alarm will sound only when the system restarts.
CPU Fan
COM 1 RS232/422/485 Select (JP8)
1
8
COM1
VGA
6
(JP14)
9
1
COM 2
2
7
1
1
1 9
2
1
SATA 2
1
5
7
SATA 1
Nuvoton
NCT6106D
COM 9
COM 10
(optional) (optional)
9
7
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
1
5
Buzzer
5
+12V
Power
PTN3355
2
13
1
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
2 1
2
Front
Audio
10
6
5
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
USB 2.0
Chapter 5 Ports and Connectors
1
2
Realtek ALC888S
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
1
9
1
7
SATA 0
Battery
1
8
DDR4_4
PCIe 1 (PCIe x16)
2
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
35
www.dfi.com
Chapter 5
LPC Connector
KD330-Q170/H110
COM 1
RS232/422/485
Select (JP7)
6 2
2
PS/2 KB/MS
USB 5-6
USB 2.0
1
COM 1 2
RS232/422/485
Select (JP10) 1
5 1
6 2
5
6
5 1
5
(DDR4_2, DDR4_4 for KD330-Q170 only)
COM 1 RS232/Power Select (JP9)
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM 1
VGA
IC
1
6
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
1
2
LAN LED
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
14 13
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
S/PDIF
1
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
iTE
IT8893E
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
2
2
6 2
6
1
5 1
6 2
5
6
COM 1 2
RS232/422/485
Select (JP10) 1
10
5 1
5
1
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components within the system, which are typically provided by a Super I/O controller. Furthermore, it
can be used to interface firmware hubs, Trusted Platform Module (TPM) devices and embedded
controllers. Data transfer on the LPC bus is implemented over a 4 bit serialized data interface,
which uses a 24MHz LPC bus clock. For more information about LPC bus, please refer to the
Intel® Low Pin Count Interface Specification Revision 1.1’. The table below indicates the pin assignments of the LPC connector.
7
1
5
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
2
1
1
2
COM 4
COM 3
5 1
5 1
9
7
SATA 3
(JP14)
2
2
1
SATA 2
6
9
COM 2
COM 1 RS232/Power Select (JP9)
5
1
9
1
9
2 1
1
3
2
2
COM 6
COM 5
System Fan 2
4
1
3
CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM1
VGA
1
1
1
1 9
2
KD331-C236/Q170
COM 1
RS232/422/485
Select (JP7)
5
2
USB 3.0
USB 5-6
DIO
1
SMBus
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
9
7
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
PS/2 KB/MS
USB 5-6
USB 2.0
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
5
Buzzer
9
2 1
11
Intel
I211AT
Line-out
Mic-in
1
14 13
24
ATX
Power
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
DDR4_1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
2
10
6
5
1
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
USB 2.0
Chapter 5 Ports and Connectors
1
2
Realtek ALC888S
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
9
1
7
SATA 0
Battery
1
8
DDR4_4
PCIe 1 (PCIe x16)
2
2
LAN LED
Intel I211AT
Front
Audio
2
Front Panel
M.2 M Key
(for KD331-Q170)
LAN 3-4
Intel I211AT
Pin
1
3
5
7
9
11
13
13
1
19
1
7
SATA 3
7
1
SATA 4
Pin Assignment
L_CLK
L_RST#
L_FRAME#
L_AD3
L_AD2
INT_SERIRQ
5VSB
Pin
2
4
6
8
10
12
14
Pin Assignment
L_AD1
L_AD0
3V3
GND
---GND
5V
3
System
Fan 1
Buzzer
1
2
DIO
36
www.dfi.com
Chapter 5
Power Connectors
KD330-Q170/H110
IC
5
6
RS232/422/485
Select (JP10) 1
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
12 24
5
+12V
Power
PTN3355
LPC
2
DVI-D (DVI-I connector)
DP++
24
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
+3.3VDC
+12VDC
+12VDC
+5VSB
PWR_OK
GND
+5VDC
GND
+5VDC
GND
+3.3VDC
+3.3VDC
1
12
LAN 1
USB 1-2
USB 3.0
12 24
13 TPM (optional)
14
Socket LGA1151
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
Nuvoton
NCT5104D
(optional)
1
2
2
1
9
iTE
IT8893E
SMBus
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
10
COM 1
RS232/422/485
Select (JP7)
2
6 2
6
1
5 1
6 2
5
6
5 1
5
1
COM 1 RS232/Power Select (JP9)
1
5 1
5 1
1
9
2
SATA 3
5
1
9
COM 4
COM 3
7
1
9
1
3
2
2
COM 6
COM 5
System Fan 2
4
1
3
Ground
CPU Fan
COM 1 RS232/422/485 Select (JP8)
1
8
COM1
VGA
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
(JP14)
4
COM 1 2
RS232/422/485
Select (JP10) 1
7
1
5
2
2
7
1
2
1
COM 2
4
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
8
24
ATX Power
12V
Standby
Power LED
LAN 1
USB 1-2
Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1.
An ATX12V power supply unit has a standard 24-pin ATX main power connector that must be
inserted into the 24-pin connector. The 8-pin +12V power connector enables the delivery of
more +12VDC current to the processor’s Voltage Regulator Module (VRM).
1
12
DVI-D (DVI-I connector)
DP++
The power connectors from the power supply unit are designed to fit the 24-pin and 8-pin
connectors in only one orientation. Make sure to find the proper orientation before plugging
the connectors.
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
13
1
Intel I211AT
USB 3.0
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
1
DDR4_1
7
DDR4_3
DDR4_2
SATA 3.0
1
Front
Audio
10
5
1
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
USB 2.0
Chapter 5 Ports and Connectors
1
2
Realtek ALC888S
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
9
7
SATA 0
Battery
6
8
DDR4_4
PCIe 2 (PCIe x4)
1
2
LAN LED
PCIe 1 (PCIe x16)
2
Please use the recommended power supply unit with the correct wattage. Insufficient power
supplied to the system may result in system instability or the add-in boards and peripherals
not functioning properly. Calculating the system’s approximate power usage is important to
ensure that the power supply meets the system’s consumption requirements.
11
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
1
1 13
ATX power
SATA 2
6
9
1
1 9
2
KD331-C236/Q170
PS/2 KB/MS
USB 5-6
USB 2.0
1
5
2
USB 3.0
USB 5-6
DIO
1
2
2
12V
1
9
COM 9
COM 10
(optional) (optional)
1
Ground
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
9
12V power
SATA 0
5
Buzzer
9
7
5
1
S/PDIF
1 13
ATX power
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
GND
+5VDC
+5VDC
+5VDC
NC
GND
GND
GND
PS_ON#
GND
-12VDC
+3.3VDC
1
6
5 1
6 2
5
6 2
1
COM 1 2
4
2
8
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
37
www.dfi.com
Chapter 5
SMBus Connector
KD330-Q170/H110
IC
COM 1
RS232/422/485
Select (JP7)
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
5 1
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
COM 1 RS232/422/485 Select (JP8)
5
4
1
8
COM 1
VGA
3
System Fan 1 CPU Fan
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
1
12
DVI-D (DVI-I connector)
DP++
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
7
SPI Flash
BIOS
3
1
8
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
1
S/PDIF
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
COM 9
COM 10
(optional) (optional)
1
9
9
iTE
IT8893E
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
2
10
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
2
COM 2
1
COM 1 RS232/Power Select (JP9)
6
7
1
5
7
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
(JP14)
2
9
1
2
COM 3
1
9
5 1
5 1
1
9
2
SATA 3
1
9
1
2
1
3
2
2
COM 6
COM 5
COM 4
5
6
5
System Fan 2
4
1
3
CPU Fan
COM 1 RS232/422/485 Select (JP8)
1
8
COM1
VGA
1
1 9
2
1
SATA 2
1
1
KD331-C236/Q170
COM 1
RS232/422/485
Select (JP7)
5
2
USB 3.0
USB 5-6
DIO
1
SMBus
7
SATA 1
Nuvoton
NCT6106D
COM 8
COM 7
(optional) (optional)
1
1
H110/Q170
PCIe 2 (PCIe x4)
9
7
SATA 0
5
Buzzer
PS/2 KB/MS
USB 5-6
USB 2.0
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
SMBUS_Data
GND
3
1
Realtek
ALC888S
6 5
PCIe 1 (PCIe x16 )
2 1
RS232/422/485
Select (JP10) 1
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
SMBUS_Alert
SMBUS_CLK
3V3SB
PS/2 KB/MS
USB 5-6
USB 2.0
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
12
DVI-D (DVI-I connector)
DP++
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enables each
one to act as a master by initiating data transfer.
1
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
2
Front
Audio
10
6
5
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
USB 2.0
Chapter 5 Ports and Connectors
1
2
Realtek ALC888S
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
Intel
1
9
1
7
SATA 0
Battery
1
8
DDR4_4
PCIe 1 (PCIe x16)
2
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
38
www.dfi.com
Chapter 5
Front Panel Connector
KD330-Q170/H110
IC
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
RS232/422/485
Select (JP10) 1
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
1 2
COM 1 RS232/422/485 Select (JP8)
4
1
8
COM 1
VGA
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
5
+12V
Power
PTN3355
LPC
13 TPM (optional)
14
Socket LGA1151
2
12
DVI-D (DVI-I connector)
DP++
24
11 12
13
1
1
LAN 2
LAN 1
USB
3-4
USB 3.0
2
Front Panel
11
Intel
I211AT
1
2
LAN LED
Line-out
Mic-in
Clear CMOS
Data (JP1)
Battery
3
1
7
SPI Flash
BIOS
1 2
8
This connector provides several control and LED indicator functions.
PCIe 1 (PCIe x16 )
3
1
Realtek
ALC888S
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
Intel
1
PWR-BTN
RESET-SW
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
PWR-LED
HDD-LED
1
S/PDIF
1
2
1
2
9
iTE
IT8893E
(for KD330-Q170 only)
1
2
19
11
10
USB 2.0
USB 9-10 USB 7-8
1
10
2
2
1
2
10
COM 1
RS232/422/485
Select (JP7)
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1
5 1
5 1
1
9
1
COM 5
1
9
2
COM 4
COM 3
SATA 3
5
9
2
7
RESET SW - Reset Switch
11 12
1
3
2
This switch allows you to reboot the system without having to power off the system.
COM 6
PWR-BTN - Power Button
System Fan 2
4
1
3
CPU Fan
COM 1 RS232/422/485 Select (JP8)
This switch is used to power on or off the system.
1
8
COM1
VGA
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
(JP14)
2
COM 2
This LED will be lit when the hard drive is being accessed.
7
1
5
2
1
2
1
SATA 2
6
9
1
1 9
2
KD331-C236/Q170
PS/2 KB/MS
USB 5-6
USB 2.0
1
5
2
USB 3.0
USB 5-6
DIO
1
SMBus
7
SATA 1
Nuvoton
NCT6106D
Nuvoton
NCT5104D
(optional)
1
9
COM 9
COM 10
(optional) (optional)
9
HDD-LED - Hard Drive LED
7
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
1
5
Buzzer
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
12
DVI-D (DVI-I connector)
DP++
PWR-LED - Power/Standby LED
1
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
SATA 3.0
1
PCIe 2 (PCIe x4)
Battery
Front
Audio
10
1
2
1
9
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
2
COM 4
1
2
COM 5
9
1
2
COM 6
9
1
2
SPI Flash
BIOS
USB 3.0
USB 5-6
11
10
2
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
USB 2.0
Chapter 5 Ports and Connectors
1
2
Realtek ALC888S
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
5
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
6
7
SATA 0
6
1
2
HDD-LED
8
DDR4_4
PCIe 1 (PCIe x16)
2
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
Pin Pin Assignment
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7
RESET SW
SATA 3
7
1
SATA 4
3
System
Fan 1
3
HDD Power
5
Signal
7
Ground
9
RST Signal
11
N.C.
Pin Pin Assignment
2
LED Power
PWR-LED 4
LED Power
PWR-BTN
6
Signal
8
Ground
10
Signal
Buzzer
1
2
DIO
39
www.dfi.com
Chapter 5
Expansion Slots
KD330-Q170/H110:
IC
COM 1
RS232/422/485
Select (JP7)
6 2
2
PS/2 KB/MS
USB 5-6
USB 2.0
1
COM 1 2
RS232/422/485
Select (JP10) 1
COM 1
VGA
6
5 1
6 2
5
6
5 1
5
3
1
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
1
8
5
+12V
Power
LPC
13 TPM (optional)
14
Socket LGA1151
2
PCI Express x16 Slot (Gen3 signal)
1
12
DVI-D (DVI-I connector)
DP++
KD330-Q170/H110
Q170
1
7
SPI Flash
BIOS
3
1
8
PCI Express x4 Slot: internal without access from external chassis slot
PCIe 1 (PCIe x16 )
Realtek
ALC888S
3
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
Intel
S/PDIF
1
SATA 0
1
Nuvoton
NCT5104D
(optional)
1
9
2
2
1
9
9
iTE
IT8893E
SMBus
(for KD330-Q170 only)
1
2
19
5
11
10
USB 2.0
USB 9-10 USB 7-8
1
2
1
10
2
10
1
1 9
2
2
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
7
2
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
SATA 3
(JP14)
9
1
2
COM 3
5 1
5 1
1
9
2
COM 4
1
9
1
3
2
2
COM 6
COM 5
PCI Express x16 (x16 or x8 Gen3 signal) Slot
System Fan 2
4
1
3
CPU Fan
Install a PCI Express x16 (lanes) expansion card such as a graphics card into this slot. It shares
the signal with the below PCIe x8 slot. To install a graphics card into this slot, align the graphics
card above the slot then press it down firmly until it is completely seated in the slot. The retaining
lever on the end of the slot will automatically hold the graphics card in place.
5
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
PCI Express x 8 (Gen3 signal) Slot: internal without access from external chassis slot
ATX Power
M.2 slot (key B)
The second PCIe x8 slot shares the signal with the above PCIe x16 slot. The PCIe x16 automatically
switches to x8 signal when this slot is occupied.
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
KD331-C236/Q170
1
LAN 2
USB 3-4
13
1
Intel I211AT
USB 3.0
Q170
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
11
1
7
DDR4_3
DDR4_2
PCIe x8 (Gen3)
2
Front
Audio
10
5
1
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
1
7
SATA 1
To set up and enable Intel® Optane™ technology, please configure the SATA controller mode
to “Intel RST Premium With Intel Optane System Acceleration” and install the Intel® Rapid
Storage Technology driver (15.5 or later). Refer to Chapter 7 and 8 for more information.
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
9
1
7
SATA 0
Battery
6
Intel® Optane™ Configuration
SATA 3.0
1
PCIe 2 (PCIe x4)
1
8
DDR4_4
PCIe 1 (PCIe x16)
2
Install PCI Express expansion cards to expand the I/O capability of the system.
2
LAN LED
DDR4_1
Intel I211AT
Intel I211AT
PCI Express x4 (Gen3 signal) Slots
2
Front Panel
M.2 M Key
(for KD331-Q170)
PCIe x16 (x16 or x8 Gen3)
PCIe x4 (Gen3)
The M.2 slot supports both M.2 Type 2260 and 2280 (Key B) form factors. In WM342-KD331 with the
Intel® C236 chipset, it further supports the Intel® Optane™ memory module.
5
1
9
7
1
+12V
Power
PTN3355
PCIe x4 (Gen3)
KD331-C236/Q170:
SATA 2
1
5
COM 1 RS232/422/485 Select (JP8)
8
COM1
VGA
7
SATA 1
1
6
1
COM 2
COM 1
RS232/422/485
Select (JP7)
1
2
USB 3.0
USB 5-6
DIO
1
2
PS/2 KB/MS
USB 5-6
USB 2.0
7
1
Nuvoton
NCT6106D
COM 9
COM 10
(optional) (optional)
Mini PCIe slot
(for KD330-Q170 only)
1
H110/Q170
PCIe 2 (PCIe x4)
9
Install PCI Express cards such as network cards or other expansion cards. Note that the
KD330-Q170 board supports PCIe Gen3 x4 (lanes) whereas the KD330-H110 board supports
PCIe Gen2 x4 (lanes).
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
5
Buzzer
COM 8
COM 7
(optional) (optional)
C236
These PCI slots support PCI expansion cards.
2
LAN LED
Clear CMOS
Data (JP1)
Battery
1
PCIe x4 (Gen2)
PCI Slots
2
11
Intel
I211AT
PCIe x16 (Gen 3) PCIe x16 (Gen 3)
PCIe x4 (Gen3)
13
1
Front Panel
Line-out
Mic-in
PCI
Install a PCI Express x16 (lanes) expansion card such as a graphics card into the PCIe x16
(lanes) slot. To install a graphics card into this slot, align the graphics card above the slot then
press it down firmly until it is completely seated in the slot. The retaining lever on the end of
the slot will automatically hold the graphics card in place.
Standby
Power LED
1
LAN 2
LAN 1
USB
3-4
USB 3.0
H110
PCI
24
ATX
Power
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
The KD330-Q170 board is equipped with a full-size Mini PCIe slot (PCIe/USB/SATA signals).
This slot supports the installation of a Mini PCIe or an mSATA card. To switch the interface
between Mini PCIe and mSATA, please refer to Jumper Settings in Chapter 4.
System Fan 1 CPU Fan
COM 1 RS232/422/485 Select (JP8)
4
PTN3355
Mini PCIe Slot (only for KD330-Q170)
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
COM 1 RS232/Power Select (JP9)
19
1
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
BIOS Setting
DIO
Configure these PCIe slots including their speed in the Advanced menu (“PCI Express Configuration” submenu) of the BIOS. Refer to Chapter 7 for more information.
USB 2.0
40
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Standby Power LED
Battery
KD330-Q170/H110, KD331-C236/Q170
KD330-Q170/H110, KD331-C236/Q170
COM 1
RS232/422/485
Select (JP7)
2
PS/2 KB/MS
USB 5-6
USB 2.0
1
COM 1 2
RS232/422/485
Select (JP10) 1
COM 1
VGA
6 2
IC
6
5 1
6 2
5
6
5 1
5
COM 1 RS232/Power Select (JP9)
3
1
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
DDR4_2
DDR4_4
DDR4_1
DDR4_3
4
System Fan 1 CPU Fan
1
8
5
+12V
Power
2
6 2
6
1
5 1
6 2
5
6
COM 1 2
RS232/422/485
Select (JP10) 1
COM 1 RS232/422/485 Select (JP8)
4
PTN3355
(DDR4_2, DDR4_4 for KD330-Q170 only)
1
5 1
5
1
COM 1 RS232/Power Select (JP9)
13 TPM (optional)
14
Socket LGA1151
1
1
8
5
+12V
Power
PTN3355
14
Socket LGA1151
2
2
3
COM 1 RS232/422/485 Select (JP8)
4
COM1
VGA
LPC
System Fan 2
4
CPU Fan
LPC
13
TPM (optional)
1
1
12
12
DVI-D (DVI-I connector)
DP++
LAN 1
USB 1-2
Standby Power LED
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
2
1
Intel I211AT
USB 3.0
Front Panel
1
M.2 M Key
(for KD331-Q170)
2
LAN LED
Battery
Clear CMOS
Data (JP1)
LAN 3-4
7
SPI Flash
BIOS
3
1
M.2 M Key Supports
Optane Memory
(for KD331-C236)
8
PCIe 1 (PCIe x16 )
11
1
7
DDR4_3
DDR4_2
Intel
1
S/PDIF
1
9
2
1
2
Nuvoton
NCT5104D
(optional)
1
2
9
1
iTE
IT8893E
(for KD330-Q170 only)
1
2
11
10
2
5
1
2
USB 3.0
USB 5-6
DIO
19
SMBus
USB 2.0
USB 9-10 USB 7-8
1
10
1
2
10
1
2
COM 2
9
1
7
2
SATA 2
6
1
5
1 (JP13)(JP12)(JP11)
2 6 2 6 2 6
(JP14)
2
1
1 9
2
7
1
2
COM 3
9
5 1
5 1
1
2
COM 4
9
7
2
COM 5
1
2
6
1
5
1
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
5
2
1
1
1
Chassis Intrusion
1
2
PCIe 4 (PCIe x4)
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
1
6
5 6
5
2
1 2
5
1
S/PDIF
3
COM 6
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
2
1
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
6
9
1
7
SATA 1
Intel
Realtek ALC888S
SATA 3
9
10
1
5
1
Front
Audio
2
7
SATA 0
Battery
7
SATA 1
Nuvoton
NCT6106D
COM 9
COM 10
(optional) (optional)
9
PCIe 2 (PCIe x4)
Intel I211AT
SATA 0
1
H110/Q170
PCIe 2 (PCIe x4)
COM 8
COM 7
(optional) (optional)
9
1
5
Buzzer
SATA 3.0
1
Chassis
1
Intrusion
Mini PCIe
2
(for KD330-Q170 only) SATA 3.0
8
DDR4_4
PCIe 1 (PCIe x16)
3
Mini PCIe Signal Select (JP6)
(for KD330-Q170 only)
PCI 1
2
LAN LED
DDR4_1
Intel I211AT
1
Realtek
ALC888S
2
Front Panel
11
Intel
I211AT
13
13
1
Line-out
Mic-in
24
ATX Power
Standby
Power LED
1
LAN 2
LAN 1
USB
3-4
USB 3.0
DVI-D (DVI-I connector)
DP++
ATX
Power
Standby
Power LED
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 1
USB 1-2
USB 3.0
24
1
2
USB 7-8
19
1
Battery
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
This LED will be red when the system is in the standby mode. It indicates that there is power
on the system board. Power off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
41
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
LAN LED
KD330-Q170/H110, KD331-C236/Q170
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 5-6
USB 2.0
2
6 2
6
1
5 1
6 2
5
6
5 1
4
5
COM 1 2
RS232/422/485
Select (JP10) 1
1
COM 1 RS232/Power Select (JP9)
1
3
COM 1 RS232/422/485 Select (JP8)
1
8
COM1
VGA
System Fan 2
4
CPU Fan
5
+12V
Power
PTN3355
14
Socket LGA1151
2
LPC
13
TPM (optional)
1
12
DVI-D (DVI-I connector)
DP++
24
ATX Power
Standby
Power LED
LAN 1
USB 1-2
Intel I219LM
USB 3.0
1
LAN 2
USB 3-4
Intel I211AT
USB 3.0
13
1
LAN 3-4
M.2 M Key Supports
Optane Memory
(for KD331-C236)
1
DDR4_1
7
DDR4_3
SATA 3.0
1
PCIe 2 (PCIe x4)
2
Front
Audio
10
5
1
5
1
1
1
2
PCIe 4 (PCIe x4)
9
1
1
Chassis Intrusion
Nuvoton
NCT6106D
SMBus
3
5
Clear CMOS
Data (JP1)
(JP13) (JP12)
1
6
5 6
5
2
1 2
5
1
S/PDIF
9
COM 2
1
COM 3
9
1
COM 4
1
COM 5
9
1
COM 6
9
2
2
2
SPI Flash
BIOS
USB 3.0
USB 5-6
1
11
10
2
2
1
2
Realtek ALC888S
1
10
1
2
USB 9-10
or Optional
Vertical USB
10
1
2
USB 7-8
7
SATA 2
C236/Q170
COM 2 RS232/Power Select (JP14)
2
1
7
SATA 1
Intel
COM 2 RS232/422/485 Select (JP11)
PCIe 3 (PCIe x16)
6
7
SATA 0
Battery
6
8
DDR4_4
PCIe 1 (PCIe x16)
1
1 2
2
LAN LED
DDR4_2
2
LAN LED
11
Intel I211AT
Intel I211AT
2
Front Panel
M.2 M Key
(for KD331-Q170)
19
1
7 8
7
SATA 3
7
1
SATA 4
3
System
Fan 1
Buzzer
1
2
DIO
USB 2.0
The LAN LED connector is used to detect the connection state of RJ45 LAN ports when the
connection is made to an active network via a cable. The pin functions of the LAN LED connector are listed below.
Pin
Pin Assignment
Pin
Pin Assignment
1
GBE_LED_1000-
2
GBE_LED_100-
3
GBE_LED_LINK_ACT-
4
3V3DU
5
LINK_1000_2
6
LINK_100_2
7
LINK_ACTIVITY_2
8
3V3DU
42
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 6
Chapter 6 - Mounting Options
The mechanical drawing of the wall mount illustration with dimentions.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
25.50
There are 2 mount brackets available:
•
Wall mount
Ø4.60
•
230
160
80
40
Ø3.60
Rack-mount tray bracket
Wall Mount
25.50
Wall mount kit include:
•
2 wall mount brackets
1. On the bottom of the system, use 4 mounting screws to secure the wall mount brackets on
each side of the system.
Ø3.60
Mounting screw
230
160
80
40
Mounting screw
Ø4.60
342
385
Mounting screw
Mounting screw
43
Chapter 6 Mounting Options
www.dfi.com
Chapter 6
Rack Tray Mount
Rack-mount tray kit include:
•
2 Rack-mount tray brackets
1. Place the system on the rack-mount tray and align the mounting holes of the tray with the
mount bracket.
2. Follow the rack manufacture's instruction to properly secure the system to the rack.
44
Chapter 6 Mounting Options
www.dfi.com
Chapter 7
Chapter 7 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Move the highlight left or right to select a menu
Up and Down arrows
Move the highlight up or down between submenu or fields
<Esc>
Exit the BIOS Setup Utility
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup Defaults
<F10>
Save and Exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
45
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23.
Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January
to December. Date displays the date, from 1 to 31. Year displays the year, from 1980 to
2099.
46
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ACPI Settings
CPU Configuration
This section configures system’s ACPI parameters.
This section configures the CPU.
Wake on LAN
Intel® SpeedStep™
Enable or disable WOL (wake-on-LAN) to wake the system through an Ethernet adapter.
Enable or disable the Enhanced Intel SpeedStep® Technology, which helps optimize the
balance between system’s power consumption and performance. After it is enabled in the
BIOS, you can take advantage of its offering by setting power schemes from the operating
system’s power options.
Wake on PS/2
Enable or disable the use of PS/2 devices to wake the system.
Turbo Mode
After G3
Enable or disable processor turbo mode, which allows the processor core to automatically
run faster than the base frequency by taking advantage of thermal and power headroom.
Specify which state the system should be in when power is re-applied after a power
failure (G3, the mechanical-off, state).
Always On The system is powered on.
Always Off The system is powered off.
CPU C States
Enable or disable CPU Power Management. It allows the CPU to go to C states when it’s
not 100% utilized.
Wake on RTC/Wake up Time
Enable this function to automatically power the system up at a particular time every day
from the real-time clock battery. Specify the wake up time of the day below: <hour>,
<minute>, <second>. The default is disabled.
Hyper-Threading
Enable Intel® Hyper-Threading Technology (HT) on the processor to improve performance
of operating systems and software that are optimized for hyper-threading technology.
Please check the software specifications to determine if enabling HT can be advantageous
to the overall system performance.
47
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Video Configuration
Internal Graphics Device
This section configures the video settings. Note that the configuration options vary depending
on the “Boot type” selected in the “Boot” menu.
Enable, disable or automatically detect the internal graphics.
Boot display
Prioritize device combination for display during system boot. Note that this option will
be shown only if the “Boot type” is set to “Dual” or “Legacy”.
The options are as follows:
DVI+DP1
DVI+VGA
DP1+DVI
DP1+VGA
VGA+DVI
VGA+DP1
Primary Display
Select the primary display for the system. Note that this option will be shown only if the
“Boot type” is set to “Dual” or “UEFI”. Depending on your selection, the order of video
device initialization will be as follows:
Auto mode: PEG (PCIe Graphics devices connected to PEG lanes directly routed from
the CPU )->PCIe graphics devices->PCI graphics devices->IGFX (internal graphics)
IGFX: IGFX (internal graphics)->PEG (PCIe Graphics devices connected to PEG lanes directly routed from the CPU)->PCIe graphics devices->PCI graphics devices
PEG: PEG (PCIe Graphics devices connected to PEG lanes directly routed from the CPU)
->PCIe graphics devices->PCI graphics devices->IGFX (internal graphics)
PCIe: PCIe graphics devices->PEG (PCIe Graphics devices connected to PEG lanes directly
routed from the CPU )->IGFX (internal graphics)->PCI graphics devices
48
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Audio Configuration
SATA Configuration
This section configures the audio settings.
This section configures SATA controllers.
HD Audio
Control the detection of the high-definition audio devices.
Disabled
High-definition audio devices will be unconditionally disabled.
Enabled
High-definition audio devices will be unconditionally enabled.
Auto
High-definition audio devices will be enabled if present and disabled otherwise.
49
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
USB Configuration
This section configures the parameters of the USB devices.
SATA Controller(s)
Enable or disable Serial ATA controllers.
SATA Speed
Select Serial ATA device speed from Gen1 (1.5 Gbit/s), Gen2 (3 Gbit/s), Gen 3 (6
Gbit/s) or auto.
SATA Mode Selection
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).
RAID Mode
This option allows you to create RAID using Intel® Rapid Storage Technology.
Intel RST Premium With Intel Optane System Acceleration Mode
Configure the SATA controller to use the “Intel RST Premium With Intel Optane System
Acceleration” mode to use this technology to accelerate system performance and responsiveness. Note that only KD331-C236 supports Intel® Optane system acceleration.
Serial ATA Port 0 to 5 and Hot Plug
Enable or disable each Serial ATA port and its hot plug function.
SATA Port 5 controls the signal of the M.2 slot.
Note that for WM342-KD330 (KD330-H110), the SATA port will be numbered from 0 to 3.
And for WM342-KD330 (KD330-Q170), it will be numbered from 0 to 4 (port 4 controls the
signal of the Mini PCIe slot).
Legacy USB Support
Disabled
Disable USB keyboard/mouse/storage support.
Enabled
Enable USB keyboard/mouse/storage support.
UEFI Only
Enable USB keyboard/mouse/storage support only under the UEFI environment.
XHCI Hand-off
Enable this function for operating systems that do not support xHCI Hand-off. The XHCI
ownership change will be claimed by the XHCI driver.
50
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PCI Express Configuration
This section configures the settings of PCI Express root ports.
LAN 3 and LAN 4 are only available for WM342-KD331.
For each PCIe root port above, press “Enter” to configure its speed and hog plug.
PCI Express Configuration
Select a PCI Express root port and press “Enter” to configure.
Enable/Disable
PCI Express Root Port
PCIE
PCIE
PCIE
PCIe
PCIE
1: PCIE1
2: PCIE2
3: PCIE3
slot)
4: PCIE4
Enable or disable this PCI Express root port.
slot
slot
slot (Note for KD330-Q170, this controls the signal of the full-size Mini
PCIe Speed
Select the speed of the PCI Express root port: Auto, Gen1 (2.5 GT/s), Gen2 (5 GT/s) or
Gen3 (8 GT/s).
slot (Note this is only available for KD331-C236/Q170)
Hot Plug
M.2 PCIE: M.2 slot (Note this is only available for KD331-C236/Q170)
Enable or disable the hot plug function of the PCIe root port.
LAN 1~LAN 4
51
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ME Configuration
Active Management Technology Support
This section configures flashing of the Intel® Management Engine.
The section allows you to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Refer to Chapter 10 - Intel AMT Settings for more information. Note
that this function is not available for the Intel® Core™ i3, Intel® Pentium®, Intel® Celeron®
processors or the Intel® H110 chipset.
Me Fw Image Re-Flash
Enable or disable Intel® Management Engine firmware flashing when updating the BIOS.
Intel AMT Support
Enable or disable Intel® Active Management Technology BIOS extension.
Un-Configure ME
Clears all ME related configurations without requiring a password on the next boot.
52
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
UEFI Device Manager
Network Device List
This Device Manager menu is used to configure UEFI network settings when the “Network
Stack” is enabled in the “Dual” or “UEFI” boot mode or when the PXE Boot to LAN is enabled
in the “Legacy” boot mode. Refer to the “Boot” section in this chapter. After this function is
selected, the screen will warn you that you are going to exit the BIOS setup utility.
The “Device Manager” screen is displayed. And if the “Network Stack” or the “PXE Boot to
LAN” option is enabled from the “Boot” menu, the “Network Device List” should be shown
in the “Device list”. Select “Network Device List” to view all of the detected network devices. For each network device, you can select to view and configure its settings. In addition,
you can select either the IPv4 or IPv6 network settings for UEFI network configuration.
NIC Configuration Menu
This screen shows hardware information for the Ethernet controllers and configures
their operation.
53
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Blink LEDs
IPv6 Network Configuration
Enter the duration (seconds) for the Ethernet’s LED to blink to indicate its presence.
If you select to use IPv6 network settings, enter the Interface ID (64 bit).
Policy: Select either automatic or manual. And select "Advanced Configuration" to
configure IPv6 network address manually if the manual option is selected.
New IPv6 address: Enter the IP address for the network device in the IPv6 format:
x : x : x : x : x : x : x : x (x can be any hexadecimal value between 0 and FFFF). Place a
space to separate each IP address to enter more than one address.
New Gateway addresses: Enter gateway addresses in the IPv6 format.
New DNS addresses: Enter DNS (Domain Name System) server IP addresses in the IPv6
format.
NIC Configuration
This screen configures the Ethernet controller. Select the link speed from the following options: Auto Negotiated, 10Mbps Half, 10Mbps Full, 100Mbps Half, and 100Mbps Full.
IPv4 Network Configuration
This screen configures the IP addressing method (DHCP or static IP). For static IP addressing, configure the following:
Local IP address and subnet mask: Enter the IP address for the network device in the
IPv4 format:
x . x . x . x (x must be a decimal value between 0 and 255).
Local Gateway: Enter the gateway address in the IPv4 format.
Local DNS (Domain Name System) Servers: Enter DNS (Domain Name System) server IP
addresses in the IPv4 format.
54
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Super IO Configuration
This section configures the system super I/O chip parameters.
COM Port 1 and COM Port 6
Enable or disable each serial port.
SYS Smart Fan/CPU Smart Fan/SYS Smart Fan 2 Control
Disable Disable this serial port.
Enable or disable the smart fan control.
Enable
Enable this serial port.
It also shows the Base I/O address and the assigned interrupt number.
Boundary 1 to Boundary 4
For COM Port 1 and COM Port 2, you can enable or disable the RS485 auto flow mechanism.
Set the boundary temperatures that determine the operation of the fan with different
fan speeds accordingly. For example, when the system or the CPU temperature reaches
boundary temperature 1, the system or CPU fan should be turned on and operate at
the designated speed.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable WDT.
Input any value between 1 and 255.
The range of the temperature is from 0 to 127oC.
Case Open
Fan Speed Count 1 to Fan Speed Count 4
Enable or disable the case open function.
Set the fan speed. The range is from 1 (lowest speed)-100% (full speed).
55
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PC Health Status
This section displays PC health information such as the voltages and CPU and system temperatures.
56
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Console Redirection
COMA to COMF/PCI Serial Port
Enable or disable the serial redirection function for each of the serial ports on the system. And configure the serial communication parameters to be used between the system
and a remote station.
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
UseGlobalSetting
Choose to use the pre-configured global settings from the previous menu or configure a
different setting for each serial port.
Console Serial Redirect
Enable or disable the console redirection function. (The default is disabled.) If you select
to enable it, please configure the following parameters for serial communication between
the system and a remote station:
Terminal type: VT_100, VT_100+, VT_UTF8, or PC_ANSI.
Baud rate: 115200, 57600, 38400, 19200, 9600, 4800, 2400 or 1200.
Data bits: 8 bits or 7 bits.
Parity: None, Even or Odd.
Stop bits: 1 bit or 2 bits.
Flow control: None, RTS/CTS or XON/XOFF
This is the global setting for all of the designated serial ports for the console redirection
function.
57
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Security
This section configures the security for the BIOS Setup utility and the optional Trusted
Platform Module (TPM) function.
TPM Availability
Set Supervisor Password
Show or hide TPM availability and its configurations.
Set the administrative password for entering the BIOS utility or upon entering the
power-on self-test (POST) process. The length of the password must be greater than 1
character and less than or equal to 10 characters.
TPM Operation (optional)
Enable or disable the TPM function. It displays the following options:
• No Operation: No changes to the current state.
• Disable: Disable and deactivate TPM.
• Enable: Enable and activate TPM.
Power-on Password
If you select to set the supervisor password, this option will be shown. Enable or disable
prompt for password at boot.
Clear TPM
Remove all TPM ownership contents.
58
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Boot
This section configures boot options.
Numlock
Select the power-on state for the Num Lock key.
Boot Type
Select the boot type. The options are Dual Boot, Legacy Boot and UEFI Boot Type.
Network Stack
This option is shown only when the boot type is set to Dual or UEFI.
Enable or disable UEFI network stack. It supports the operation of these functions or software: Windows 8 BitLocker Network Unlock, UEFI IPv4/IPv6 PXE and legacy PXE option ROM.
If this function is enabled, you can then go to “Advanced”>”Device Manager” to configure
network settings for network connection under the UEFI environment.
PXE Boot Capability (UEFI mode) /PXE Boot to LAN (Legacy mode)
Enable or disable Preboot eXecution Environment (PXE) boot to LAN. In the UEFI or Dual boot
mode, this function can only be enabled if the Network Stack support is enabled.
USB Boot
Enable or disable booting to USB boot devices.
Quiet Boot
Enable or disable the quiet boot function to configure the screen’s display between
POST messages or the OEM logo at bootup. Select Disabled to display the POST messages
59
and select Enabled to display the OEM logo.
Chapter 7 BIOS Setup
Boot Device Priority
This section configures legacy or EFI boot order or both depending on the “Boot Type” selected.
EFI Boot Menu
Use + and - keys to arrange the priority of the boot devices in the list.
Legacy Boot Menu
Normal
For this option, determine the boot order for the devices within each category. Use the
+ and - key to arrange the priority of the boot type devices in the list. The first device
in the list has the highest boot priority.
Advance
For this option, determine the boot order for all bootable devices. Use + and - keys to
arrange the priority of the detected boot devices in the list. The first device in the list
has the highest boot priority.
www.dfi.com
Chapter 7
Exit
This section configures the parameters for exiting the BIOS setup utility.
Exit Saving Changes
Select this field and press <Enter> to exit BIOS setup and save your changes.
Load Optimal Defaults
Select this field and press <Enter> to load the optimal defaults.
Discard Changes
Select this field and press <Enter>to exit the BIOS setup without saving your changes.
Save Setting to file
Select this option to save BIOS configuration settings to a USB drive. The operation will
fail if there aren’t any USB devices detected on the system. The saved configuration will
have the DSF file extension and can be used for restoration.
Restore Setting from file
Select this option to restore BIOS configuration settings from a USB drive. Note that this
option appears only if a USB device is detected on the system.
60
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need an updated BIOS file and a flash utility. Please contact
technical support or your sales representative for the files and specific instructions on how to
update BIOS with the flash utility.
1. The Intel® Management Engine has already been integrated into this system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing the BIOS update procedure. For your convenience,
we will also provide you with an auto-execution file in the BIOS file downloaded. This autoexecution file will bring you directly to the flash utility menu soon after system boots up and
finishes running the boot files in your boot disk.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
RRead file successfully.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
(path= “platform.ini”)
Information
Please do not remove the AC power
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2017, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: KD330
New BIOS Model name: KD330
Current BIOS version: B17A.31A
New BIOS version: B18A.31A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\KD330>_
100%
100%
61
Chapter 7 BIOS Setup
www.dfi.com
Chapter 8
Chapter 8 - Supported Software
The system requires you to install drivers for some devices to operate properly. To download
the latest driver, please go to the DFI Download Center:
http://www.dfi.com/DownloadCenter
Once you are in the Download Center page, select your product or type the model name and
click "Search" to find product-related resources such as documentation and drivers.
Drivers are available for the following devices in Windows 10:
•
Intel® Chipset Device Software
•
Intel® Graphics Driver
•
•
Intel® LAN Driver
Intel® ME Driver
•
Intel® Rapid Storage Technology Driver
•
Audio Driver
•
Intel® Serial IO Driver
62
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Chipset Device Software
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
Please wait while the installation is in progress.
The Intel® Chipset Device Software is used for updating Windows® INF files so that the Intel
chipset can be recognized and configured properly in the system.
To install the utility, follow these steps:
1. Setup is ready to install the
utility. Click “Next”.
4. Please wait while the installation is in progress.
2. Read the license agreement,
and then click “Yes”.
5. Click “Restart Now” to allow
the new software installation to take effect.
63
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Graphics Driver
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
To install this driver, follow these steps:
1. Setup is now ready to
install the graphics driver.
Click “Next”.
4. Setup is now installing the
driver. Click “Next” to continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is
enabled. When this is enabled and after the system reboots, the screen will turn blank for
1 to 2 minutes (while WinSAT is running) before the Windows 7/ Windows 8.1/ Windows
10 desktop appears. The “blank screen” period is the time Windows is testing the graphics
performance.
We recommend that you skip this process by disabling this function and then click “Next”.
2. Read the license agreement, and then click “Yes”.
5. Click “Yes, I want to restart
this computer now”, and
then click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
64
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel LAN Driver
4. Click “Install” to begin the
installation.
To install this driver, follow these steps:
1. Setup is preparing to install
the driver. Click “Next” to
continue.
5. After the installation is
complete, click “Finish”.
2. Click “I accept the terms in
the license agreement” if
you accept the agreement,
and then click “Next”.
3. Select the program features
you want to install, and
then click “Next”.
65
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel ME Driver
3. Setup is currently installing
the driver. After the installation is complete, click
“Next.”
To install the Intel® Management Engine (Intel® ME) Driver, follow these steps:
1. You are about to install
the driver. Click “Next”
to continue.
4. Please wait while the product is being installed.
2. Read the license agreement, and then click “Next”.
5. After the installation is
complete, click “Finish”.
66
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Audio Driver
Serial IO Driver
To install this driver, follow these steps:
To install this driver, follow these steps:
1. Setup is now ready to install the
audio driver. Click “Next”.
1. Setup is ready to install the driver.
Click “Next” to continue.
2. Follow the steps of the on-screen
instructions; click “Next” each
time you finish a step.
3. Click “Yes, I want to restart my
computer now”, and then click
“Finish”.
2. Read the license agreement carefully.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement and then
click “Next”.
Restart the system to allow the new
software installation to take effect.
67
Chapter 8 Supported Software
www.dfi.com
Chapter 8
5. Setup is now installing the driver.
3. Read the file information and then
click “Next”.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
6. Click “Finish” to exit the setup.
68
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel® Rapid Storage Technology Driver
The Intel Rapid Storage Technology is a utility that allows you to monitor the current status of the SATA drives. It enables enhanced performance and power management for the
storage subsystem. You can also install and set up Intel® Optane™ memory with the Intel®
Rapid Storage Technology application.
Please refer to Chapter 9 for more information.
69
Chapter 8 Supported Software
www.dfi.com
Chapter 9
Chapter 9 - RAID
Settings
The system board allows RAID configuration with levels of RAID 0, RAID 1, RAID 5 and RAID 10.
To enable the RAID function, the following settings are required.
RAID Levels
1. Connect the Serial ATA drives.
RAID 0 (Striped Disk Array without Fault Tolerance)
2. Enable RAID in the BIOS.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk drives.
This improves the I/O performance of the drives at different channel; however it is not fault tolerant. A failed disk will result in data loss in the disk array.
3. Create a RAID volume.
4. Install the Intel Rapid Storage Technology Utility.
RAID 1 (Mirrored Disk Array with Fault Tolerance)
Step 1: Connect the Serial ATA Drives
RAID 1 copies and maintains an identical image of the data from one drive to the other drive. If
a drive fails to function, the disk array management software directs all applications to the other
drive since it contains a complete copy of the drive’s data. This enhances data protection and
increases fault tolerance to the entire system. Use two new drives or an existing drive and a new
drive but the size of the new drive must be the same or larger than the existing drive.
Refer to carrier board manual for details on connecting the Serial ATA drives.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID BIOS utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
RAID 5 (Striped Disk Array with Distributed Parity)
RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides
better hard drive performance and higher disk utilization than RAID 1.
RAID Level
Min. Drives
Protection
Description
RAID 0
2
None
Data striping without redundancy
RAID 1
2
Single Drive Failure
Disk mirroring
Single Drive Failure
Block-level data striping with
distributed parity
RAID 5
3
Step 2: Enable RAID in the BIOS
1. Power on the system then press <Del> to enter the main menu of the BIOS.
2. Go to “Advanced” menu, and select the “SATA Configuration” menu.
3. Change the “SATA Mode Selection” to “RAID” mode.
4. Save the changes in the “Exit” menu.
5. Reboot the system.
70
Chapter 9 RAID
www.dfi.com
Chapter 9
Step 3: Create a RAID Volume
Step 3-1: Create a RAID Volume if the boot type is UEFI
1. When the Intel RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
If the boot type is set to UEFI, RAID volume creation will be different. Please use the following steps to create RAID volumes. To set the boot type, enter the BIOS utility and go to “Boot”
>”Boot type”.
®
2. Select 1: Create RAID Volume and press <Enter>.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
1. In the BIOS, go to the “Advanced” > “UEFI Device Manager”.
4. Use the up or down arrow keys to select the strip size and press <Enter>.
5. Press <Enter> to select the physical disks.
6. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
7. Press <Enter>.
8. Select the volume size and press <Enter>. You must select less than one hundred percent
of the available volume space to leave space for the second volume.
9. Press <Enter> to create the volume.
10. At the prompt, press <Y> to confirm volume creation.
11. Select 4: Exit and press <Enter>.
12. Press <Y> to confirm exit.
2. Select Device Manager. The system will prompt you that it is going to exit the BIOS utility.
Select “OK” to continue.
Note:
These steps are cited from the Intel® Support site, “Set Up a System with Intel®
Matrix RAID Technology” (Article ID: 000005789).
3. The “Intel® Rapid Storage Technology” menu appears. Enter this menu.
71
Chapter 9 RAID
www.dfi.com
Chapter 9
Step 4: Install the Intel Rapid Storage Technology Utility
3. The screen displays all available drives. Select “Create RAID volume” to create a RAID
volume”.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/or
SATA drives. Furthermore, It enables enhanced performance and power management for the
storage subsystem.
4. Use the up or down arrow keys to select the RAID level and press <Enter>.
5. Use the up or down arrow keys to scroll through the list of hard drives and press <Enter>
and select “x” to select the drive for the RAID group.
7. Use the up or down arrow keys to select the strip size and press <Enter>.
1. Insert the provided DVD into an optical drive.
8. Enter the capacity for the volume and press <Enter>.
2. Click “Intel Rapid Storage Driver” on the main menu.
9. Select “Create Volume” to start creating the volume.
3. Setup is ready to install
the utility. Click “Next” to
continue.
4. Read the license agreement and click “I accept
the terms in the License
Agreement“ if you accept
the agreement. Then, click
“Next”.
72
Chapter 9 RAID
www.dfi.com
Chapter 9
5. Go through the readme
document to view system
requirements and installation information, then click
“Next”.
8. Click “Yes, I want to restart
this computer now” to
complete the installation
and click “Finish”.
6. Click “Next” to install to
the default folder or click
“change” to choose another
destination folder.
7. Confirm the installation and
click “Next”.
73
Chapter 9 RAID
www.dfi.com
Chapter 10
6
Chapter
Chapter 10 - Intel AMT Settings
Enable Intel® AMT in the Insyde BIOS
Overview
1. Power on the system then press <Del> to enter the main menu of the BIOS setup utility.
Intel Active Management Technology (Intel AMT) combines hardware and software solutions
to provide maximum system defense and protection to networked systems. Note that SKUs
with the Intel® H110 chipset or Intel® Core™ i3, Celeron® and Pentium® processors do not
support iAMT.
2. In the “Advanced” menu, select “Active Management Technology Support”.
®
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
• Discover
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
• Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
3. In the “Active Management Technology Support” menu, select “Enabled” for
“Intel AMT Support”.
74
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
Set up Intel® AMT using the Intel® Management
Engine BIOS Extension (MEBX)
4. In the “Exit” menu, select “Exit Saving Changes” and then select “OK”.
1. After the system reboots, press <Del> to enter the BIOS menu again.
2. In the “Advanced” menu, select “MEBX Configuration” to enter the Manageability Engine
BIOS Extension (MEBx) Setup.
3. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password,
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
75
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
4. Enter a password in the space provided under “Intel(R) ME Password” and then press
“Enter”. The password must include:
•
•
•
•
•
5. You will be asked to verify the password. Enter the same new password in the space provided under “Verify Password” and then press “Enter”.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Enter] = Select Entry
[Esc]= Exit
6. Select “Intel(R) ME General Settings” and then press “Enter”.
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
76
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
7. Select “Change Intel(R) ME Password” and then press “Enter”.
8.Select “Local FW Update” and then press “Enter”. Select “Enabled” or “Disabled” or
“Password Protected” and then press “Enter”.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under “Intel(R) ME New Password” and then press “Enter”.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Disabled
Enabled
Password Protected
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
<Enabled>
Intel(R) ME New Password
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9. Select Previous Menu until you return to the “Main Menu”. Select “Intel(R) AMT Configuration” and then press “Enter”.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
[Esc]= Exit
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
[↑↓] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
77
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
10. In the “Intel(R) AMT Configuration” menu, select “Manageability Feature Selection” and
then press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
12. In the “SOL/Storage Redirection/KVM” menu, select “Username and Password” and then
press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
11. In the “Intel(R) AMT Configuration” menu, select “SOL/Storage Redirection/KVM” and
then press “Enter”.
13. In the “SOL/Storage Redirection/KVM” menu, select “SOL” and then press “Enter”. Select
“Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Anytime>
<Full Unprovision>
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
78
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
14. In the “SOL/Storage Redirection/KVM” menu, select “Storage Redirection” and then press
“Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
16. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“User Consent” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) AMT CONFIGURATION
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Manageability Feature Selection
> SOL/Storatge Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
<Anytime>
<Full Unprovision>
[↑↓] =Move Highlight [Enter] =Select Entry [Esc] =Exit
15. In the “SOL/Storage Redirection/KVM” menu, select “KVM Feature Selection” and then
press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
17. In the “User Consent” menu, select “User Opt-in” and then press “Enter”. Select “None”,
“KVM” or “ALL” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Enabled>
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
79
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
20. In the “Intel(R) AMT Configuration” menu, select “Network Setup” and then press “Enter”.
18. In the “User Consent” menu, select “Opt-in Configurable from Remote IT” and then press
“Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
< ALL>
< Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] =Move Highlight
<Enabled>
<Anytime>
<Full Unprovision>
[Enter] =Select Entry
[Esc] =Exit
21. In the “Intel(R) ME Network Setup” menu, select “Intel(R) ME Network Name Settings”
and then press “Enter”.
19. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“Password Policy” and then press “Enter”.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
> Intel(R) ME Network Name Settings
> TCP/IP Settings
Manageability Feature Selection
<Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Setup And Configuration
Anytime
[↑↓] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
80
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
22. In the “Intel(R) ME Network Name Settings” menu, select “Host Name” and then press
“Enter”. Enter the computer’s host name and then press “Enter”.
24. Select “Shared/Dedicated FQDN” and then press “Enter”. Select “Shared” or “Dedicated”
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Dedicated
Shared
Computer Host Name
[Enter] =Complete Entry
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc] =Discard Changes
23. Select “Domain Name” and then press “Enter”. Enter the computer’s domain name and
then press “Enter”.
25. Select “Dynamic DNS Update” and then press “Enter”. Select “Enabled” or “Disabled” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Computer Domain Name
_
_
<Shared>
<Disabled>
Disabled
Enabled
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
81
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
26. Select Previous Menu until you return to the “Intel(R) ME Network Setup” menu. Select
“TCP/IP Settings” and then press “Enter”.
28. In the “Intel(R) AMT Configuration” menu, select “Activate Network Access” and then
select “Yes/No” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.5.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
TCP/IP SETTINGS
DHCP Mode
> Wired LAN IPV4 Configuration
<Enabled>
Disabled
Enabled
[↑↓] =Move Highlight
[Enter] =Select Entry
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[Esc] =Exit
27. In the “TCP/IP Settings” menu, select “Wired LAN IPV4 Configuration” and then press
“Enter”.
29. In the “Intel(R) AMT Configuration” menu, select “Unconfigure Network Access” and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.5.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
INTEL(R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Enabled>
Disabled
Enabled
<Enabled>
<Anytime>
<Full Unprovision>
Full Unprovision
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
82
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
30. In the “Intel(R) AMT Configuration” menu, select “Remote Setup And Configuration” and
then press “Enter”.
32. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning Record” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
[↑↓] =Move Highlight
INTEL(R) REMOTE SETUP AND CONFIGURATION
<Enabled>
<Anytime>
<Full Unprovision>
Provision Record is not present
[Enter] =Select Entry
[↑↓] =Move Highlight
[Esc] =Exit
31. In the “Intel(R) Remote Setup And Configuration” menu, select “Current Provisioning
Mode” and then press “Enter”.
[Enter] =Select Entry
[Esc] =Exit
33. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server IPV4/
IPV6”, enter “Provisioning server address” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Provisioning server address
Provisioning Mode: PKI
[↑↓] = Move Highlight
[↑↓] =Move Highlight
[Enter] =Select Entry
[Enter] = Select Entry
[Esc]= Exit
[Esc] =Exit
83
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
34. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server
FQDN”, enter the FQDN of Provisioning server, and then press “Enter”.
36. In the “Intel(R) Remote Setup And Configuration” menu, select “TLS PKI” and then press
“Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
35. In the “Intel(R) Remote Setup And Configuration” menu, select “RCFG” and press “Enter”,
and then select “Start Configuration Y/N” and press “enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL(R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Start Configuration
This will activate Remote Configuration. Continue: (Y/N)
[Enter] =Select Entry
[Esc]= Exit
37. In the “Intel(R) Remote Configuration” menu, select “Remote Configuration**” and press
“Enter”, and then select “Enabled” or “Disabled” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
[↑↓] =Move Highlight
[Enter] = Select Entry
< Enabled>
_
Disabled
Enabled
[↑↓] = Move Highlight
[Esc] =Exit
[Enter] = Select Entry
[Esc]= Exit
84
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
40. In the “Intel(R) Remote Configuration” menu, select the hash name then press Insert to
enter custom hash certificate name, press Delete to delete a hash, press Enter to view
hash information, or press + to activate or deactivate hash.
38. Select “PKI DNS Suffix”, enter the “PKI DNS Suffix”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
INTEL (R) REMOTE CONFIGURATION
< Enabled>
_
Hash Name
VeriSign Class 3
VeriSign Class 3
Go Daddy Class 2
Comodo AAA CA
Starfield Class 2
VeriSign Class 3
VeriSign Class 3
VeriSign Class 3
GTE CyberTrust G1
Baltimore Cyber Tr
Cyber Trust Global
Verizon Global Ro
Entrust. net CA (2
Entrust Root CA
VeriSign Universa
Go Daddy Root CA
Entrust Root CA Startfield Root CA
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
39. Select “Manage Hashes”, and then press “Enter”.
[Ins]= Add New Hash
[↑↓] =Move Highlight
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
[↑↓] =Move Highlight
[Delete] = Delete Hash
[Enter] = View Hash
Algorithm
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
[+] = Activate Hash
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
<Enabled>
_
[Enter] =Select Entry
Default
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
41. In the “Intel(R) AMT Configuration” menu, select “Power Control”, and then press Enter.
INTEL(R) REMOTE CONFIGURATION
Remote Configuration **
PKI DNS Suffix
> Manage Hashes
Active
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Enabled>
<Anytime>
<Full Unprovision>
[Esc] =Exit
[↑↓] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
85
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
42. In the “Intel(R) AMT Power Control” menu, select “Intel(R) AMT ON in Host Sleep States”
then press Enter. Select an option then press “Enter”.
44. Press “Esc” until you return to the “Main Menu”. Select “MEBx Exit” then press “Enter”.
Press “Y” then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
MAIN MENU
INTEL(R) AMT POWER CONTROL
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
These configurations are effective only after AMT provisioning has started
Intel(R) AMT ON in Host Sleep States <Desktop: ON in S0, ME Wake in
S3, S4-5>
Idle Timeout
65535
Desktop: ON in S0
Desktop: ON in S0, ME Wake in S3, S4-5
[↑↓] = Move Highlight
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[Enter] = Select Entry
[Esc]= Exit
43. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout” and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
[↑↓] =Move Highlight
<Enter> =Complete Entry [Esc] =Discard Changes
86
Chapter 10 Intel AMT Settings
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising