Dfi WM343-SD Manual
WM343-SD330/SD331
Desktop Box PC
User’s Manual
A47300805
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class A
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this
document. Further, the manufacturer reserves the right to revise this publication and make
changes to its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
•
•
•
Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.
•
© 2018. All Rights Reserved.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
Notice:
Trademarks
1.
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Copyright ���������������������������������������������������������������������� 2
Audio ......................................................................................................... 32
I/O Connectors....................................................................... 33
Trademarks ������������������������������������������������������������������ 2
S/PDIF Connector........................................................................................ 33
Digital I/O and Power Connector.................................................................. 34
SATA (Serial ATA) Connectors....................................................................... 35
COM (Serial) Ports....................................................................................... 36
USB Ports.................................................................................................... 37
Cooling Fan Connectors............................................................................... 38
Chassis Intrusion Connector ........................................................................ 39
LPC Connector............................................................................................. 40
Power Connectors........................................................................................ 41
SMBus Connector ....................................................................................... 42
Standby Power LED..................................................................................... 43
Battery........................................................................................................ 43
Front Panel Connector................................................................................. 44
Expansion Slots........................................................................................... 45
LVDS LCD Panel Connector.......................................................................... 46
FCC and DOC Statement on Class A ���������������������������� 2
About this Manual �������������������������������������������������������� 4
Warranty ��������������������������������������������������������������������� 4
Static Electricity Precautions ��������������������������������������� 4
Safety Measures ����������������������������������������������������������� 4
Safety Precautions ������������������������������������������������������� 5
About the Package ������������������������������������������������������� 5
Chapter 6 - Mounting Options ����������������������������������� 47
Before Using the System ��������������������������������������������� 5
Chapter 7 - BIOS Setup ��������������������������������������������� 49
Chapter 1 - Introduction ���������������������������������������������� 6
Overview ............................................................................... 49
Insyde BIOS Setup Utility........................................................ 50
Chapter 2 - Getting Started ��������������������������������������� 12
Main........................................................................................................... 50
Advanced ................................................................................................... 50
Device Manager........................................................................................... 57
Security....................................................................................................... 62
Boot........................................................................................................... 63
Exit............................................................................................................. 64
Chapter 3 - Installing Devices ����������������������������������� 13
Chapter 4 - Jumper Settings ������������������������������������ 22
Updating the BIOS.................................................................. 65
Notice: BIOS SPI ROM............................................................ 65
Clear CMOS............................................................................ 22
Serial Port RS232/422/485 Select............................................ 23
Serial Port Power Select.......................................................... 25
Power-on Select ................................................................... 26
Backlight Power Select (for SD330-Q170/H110 only)................ 27
Panel Power Select (for SD330-Q170/H110 only)...................... 27
LCD/Inverter Power Select (for SD330-Q170/H110 only)........... 28
Mini PCIe/mSATA Signal Select (for SD330-Q170 only)............. 28
Chapter 8 - Supported Software�������������������������������� 66
Chapter 9 - RAID ������������������������������������������������������ 78
Chapter 10 - Intel AMT Settings ������������������������������� 82
Chapter 5 - Ports and Connectors ���������������������������� 29
Rear Panel I/O Ports............................................................... 29
PS/2 Keyboard/Mouse Port........................................................................... 29
COM (Serial) Ports....................................................................................... 30
Graphics Interfaces...................................................................................... 30
RJ45 LAN Ports............................................................................................ 31
USB Ports.................................................................................................... 31
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The auto-run screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
2. Wear an antistatic wrist strap.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1 WM343-SD330 or WM343-SD331 System Unit
• 1 CPU cooler
• Danger of explosion if battery incorrectly replaced.
• 1 SATA Data Cable (Length: 650mm)
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• 4 HDD Screws
• 1 PSU Flex ATX 150W/250W/350W/400W/500W
• Keep this system away from humidity.
• 1 System Fan
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
Optional Items
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Power Cord
• 3.5” HDD Tray Kit
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
Before Using the System
• If one of the following occurs, consult a service personnel:
Before powering-on the system, prepare the basic system components.
- The power cord or plug is damaged.
If you are installing the system board in a new system, you will need at least the following
internal components.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
• CPU and memory modules
• Storage devices such as hard disk drive, CD-ROM, etc.
- The system is not working properly.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Key Features
Overview
Front View
Model Name
WM343-SD
Processor
6th Generation Intel® CoreTM, Pentium® and Celeron® processors
Chipset
Intel® C236 / Q170 / H110 Chipset
LAN
2 LAN ports
COM
1 COM port
Displays
1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
USB
4 USB 3.0 ports + 2 USB 2.0 ports
Audio
Mic-in, Line-out, Line-in (available upon request)
Rear View
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
System
Graphics
Processor 6th Generation Intel® CoreTM Processors (LGA 1151 Socket)
Intel® Xeon® Processor E3-1275 v5, Quad Core, 8M Cache,
3.6GHz (4.0GHz), 80W
Intel® Xeon® Processor E3-1225 v5, Quad Core, 6M Cache,
3.3GHz (3.7GHz), 80W
Controller Intel® HD Gen 9 Graphics
Feature
OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Display
1
1
1
1
Intel® Xeon® Processor E3-1268L v5, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel® Core™ i7-6700 Processor, Quad Core, 8M Cache,
3.4GHz (4.0GHz), 65W
x
x
x
x
VGA
DVI-I (DVI-D signal)
DP++
LVDS (only for SD330-Q170/SD330-H110)
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I: resolution up to 1920x1200 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
LVDS: dual channel, resolution up to 1920x1200 @ 60Hz
Intel® Core™ i7-6700TE Processor, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel® Core™ i5-6500 Processor, Quad Core, 6M Cache,
3.2GHz (3.6GHz), 65W
Triple
Display
VGA + DVI-I (DVI-D signal) + DP++
Intel Core™ i5-6500TE Processor, Quad Core, 6M Cache,
2.3GHz (3.3GHz), 35W
Storage
External
Intel® Core™ i3-6100 Processor, Dual Core, 4M Cache, 65W
1 or 2 x 3.5"/2.5" SATA 3.0 Drive Bays (1 x 3.5" SATA drive bay, by default)
1 x 5.25" Optical Drive Bay
Expansion
Interface
WM343-SD330
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
2 x PCI
1 x Full-size Mini PCIe (USB/PCIe/mSATA, PCIe by default) (only for
SD330-Q170)
®
Intel® Core™ i3-6100TE Processor, Dual Core, 4M Cache,
2.7GHz, 35W
Intel® Pentium® Processor G4400, Dual Core, 3M Cache,
3.3GHz, 65W
Intel® Pentium® Processor G4400TE, Dual Core, 3M Cache,
2.9GHz, 35W
WM343-SD331
2 x PCIe x16 (1 x16 or 2 x8 signal) (Gen 3)
2 x PCIe x4 (Gen 3)
Intel® Celeron® Processor G3900, Dual Core, 2M Cache,
2.8GHz, 65W
Audio
Codec
Realtek ALC888S-VD2-GR
Intel Celeron Processor G3900TE, Dual Core, 2M Cache,
2.6GHz, 35W
®
Chipset
®
WM343-SD330
SD330-Q170: Intel® Q170 Chipset
SD330-H110: Intel® H110 Chipset
WM343-SD331
SD331-C236: Intel® C236 Chipset
SD331-Q170: Intel® Q170 Chipset
Memory
WM343-SD331 (SD331-C236/SD331-Q170)
Four 288-pin ECC/non-ECC DIMM up to 64GB, dual channel DDR4
1866/2133MHz
WM343-SD330 (SD330-Q170)
Four 288-pin DIMM up to 64GB, dual channel DDR4 1866/2133MHz
WM343-SD330 (SD330-H110):
Two 288-pin DIMM up to 32GB, dual channel DDR4 1866/2133MHz
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
ETHERNET
Controller
1 x Intel® I210AT PCIe (10/100/1000Mbps)
1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps)
LED
Indicators
1 x Power LED
1 x HDD LED
REAR I/O
Ethernet
2 x GbE (RJ-45)
Serial
1 x RS-232/422/485 (RS-232 w/ power) (DB-9)
USB
4 x USB 3.0
2 x USB 2.0
PS/2
1 x PS/2 (mini-DIN-6)
Display
1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
Audio
1 x Line-out, 1 x Mic-in, 1 x Line-in (available upon request)
Buttons
1 x Power Button
Cooling
Fan
1 x System Fan
Environment
Operating
Temperature
0 to 45°C
Storage
Temperature
0 to 60°C
Relative
Humidity
5 to 95% RH (non-condensing)
Shock
Operating: 3G
Non-operating: 5G
Vibration
Operating: Random 5~500Hz 0.5G
Non-operating: Sine 10~500Hz 1.5G
Package
Drop
ISTA Project 1A
WatchDog
Timer
Output &
Interval
System Reset, Programmable via Software from 1 to 255 Seconds
Power
Supply
Flex ATX 250W (or optional 150/250/350/400/500W)
OS Support
and BIOS
OS
Windows 7 (/WES7) 32/64-bit
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise 64-bit
Debian 8 (with VESA graphics driver)
CentOS 7 (with VESA graphics driver)
Ubuntu 15.10 (Intel graphics driver available)
BIOS
Insyde SPI 128Mbit
Mechanical
Mechanical
Construction Sheet Metal
Compliance
Wall Mount
Dimensions
349mm x 140.2mm x 290.9mm (13.74" x 5.52" x 11.45")
Weight
TBD
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the WM343-SD
DVI-I/DP++/VGA Port
Connects the DVI-I (DVI-D signal)/DP++/VGA connector of an LCD monitor.
Front View
COM Port
Connects serial devices. COM 1 can be selected among RS232, RS422 and RS485 as well as
between RS232 and RS232 with power via jumper settings.
USB 3.0 Ports
Connect USB 3.0 devices and devices based on USB 2.0 and 1.1/1.0 versions.
USB 2.0 Ports
Connect USB 2.0 devices and devices based on USB 1.1/1.0 versions.
LAN Ports
Connect the system to a local area network.
Line-out
Connects an external speaker.
Line-in (optional)
Connects any audio devices such as CD players, audio mixers, musical instruments, etc.
Mic-in
Connects an external microphone.
Rear View
Power Button
Optical
Drive Bay
Status LED
PS/2 KB/Mouse
Connects a PS/2 keyboard and mouse.
Expansion
Slots
Expansion slots
Provides PCIe or PCI expansion connectivity.
Power Button
Press to power on or off the system.
LAN Ports
HDD LED
Status LED (Green)
Indicates system status.
Status LED
ACPI state
S0
Sleep
S4, S5
LED Behavior
ON
Blinking
Off
HDD LED (Red)
Indicates the status of hard drives.
SATA
Drive Bay
COM
VGA
HDD LED
USB 3.0 Ports
DVI-I
DP++
Line-in (optional)
PS/2 Keyboard/Mouse
Line-out
USB 2.0 Ports
Mic-in
9
Chapter 1 Introduction
HDD State
Disk access
activity
LED Behavior
Blinking
Disk drives present or not present
Off
SATA Drive Bay
Inserts a SATA drive.
Optical Drive Bay
Inserts a DVD or CD-ROM. Note that this bay can also be an optional 3.5” SATA drive bay.
www.dfi.com
Chapter 1
Mechanical Dimensions (WM343-SD330)
Mechanical Dimensions (WM343-SD331)
Rear View
290.9
290.9
Rear View
Left View
Right View
140.20
140.20
Right View
Left View
349
349
Front View
Front View
10
Chapter 1 Introduction
www.dfi.com
Chapter 1
Motherboard Dimensions (SD330-Q170)
Motherboard Dimensions (SD331-C236/SD331-Q170)
209.55
165.82
90.81
47.29
45.72
26.97
0.00
13.67
34.29
209.55
197.48
171.73
165.82
135.39
105.13
90.81
82.63
63.46
47.29
45.72
26.97
0.00
13.67
34.29
10.16
0.00
22.86
29.22
10.16
0.00
46.94
75.29
22.86
94.79
46.94
130.79
150.29
154.94
154.94
75.29
94.79
205.33
227.33
233.68
203.20
160.23
180.23
227.33
45.72
20.32
130.79
Motherboard Dimensions (SD330-H110)
150.29
154.94
154.94
209.55
165.82
90.81
45.72
47.29
26.97
0.00
13.67
34.29
205.33
10.16
0.00
227.33
233.68
22.86
29.22
203.20
180.23
227.33
45.72
20.32
75.29
160.23
46.94
94.79
130.79
150.29
154.94
154.94
205.33
227.33
233.68
203.20
180.23
227.33
160.23
45.72
11
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Getting Started
Preparing the System
Before you start using the system, you need the following items:
•
•
•
•
•
•
•
SATA hard drive
CPU
PS/2 or USB keyboard
PS/2 or USB mouse
CD-ROM drive (for installing software/drivers)
Screwdriver
Memory modules (optional)
Installing Devices
The following devices can be installed in the system.
•
•
Memory modules
SATA hard drive
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the type of
hard disk drive.
1.
2.
Power on the system.
After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing the Operating System
Most operating system software can be installed using a DVD (and DVD burner) or bootable USB
drive.
Please refer to your operating system manual for instructions on installing an operating system.
Installing the Drivers
The system comes with a software package including drivers. These drivers must be installed to
provide the best system performance. Refer to the Supported Software Chapter for instructions on
installing drivers.
12
Chapter 2 Getting Started
www.dfi.com
Chapter 3
Chapter 3 - Installing Devices
Opening the Chassis
Installing a DIMM
Please observe the following guidelines and follow the procedure to open the system.
To access the DIMM sockets, first remove the optical drive tray by uninstalling the screws from
the rear panel and inside the chassis.
1.
Make sure the system and all other peripheral devices connected to it have been powered off.
2.
Disconnect all power cords and cables.
3.
Remove the top cover by uninstalling the thumb screws.
Optical drive
tray screw
Thumb screw
Optical drive tray screw
13
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a CPU
1.
Align the notch on the DIMM with the tab in the DIMM socket.
2.
Press down on the DIMM until the release tabs spring back to secure the DIMM in place.
1. Make sure the system and all other peripheral devices connected to it have been powered-off.
2. Disconnect all power cords and cables.
3.
The system board is equipped with a surface mount LGA 1151 socket. This socket is exclusively designed for installing a LGA 1151 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1151 socket comes with a protective
cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If
the cap is missing or the cap or contact pins are damaged, contact your dealer immediately.
2. Keep the protective cap. RMA requests will be accepted and processed only if the
LGA 1151 socket comes with the protective cap.
The installed DIMM
Load lever
Protective
cap
4. Unlock the socket by pushing the load lever down, move it sideways until it is released
from the retention tab, and then lift the load lever up.
14
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
5. Remove the protective cap from the CPU socket. The cap is used to protect the CPU socket against dust and harmful particles. Remove the protective cap only to install the CPU.
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
6. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as the photo shown below.
9. Close the load plate and push the load lever down to lock it under the retention tab. While
closing the load plate, slide the front edge of the load plate under the retention tab.
7. Unlock the socket by pushing the load lever down and moving it sideways until it is released from the retention tab and then lift the load lever up.
Load lever
Protective
cap
Retention knob
Load plate
Retention tab
8. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as shown below. The CPU’s notch will at the same time fit into
the socket’s alignment key.
Alignment key
Gold triangular mark
15
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing the Fan and Heat Sink
4. Rotate each screw that are
diagonally across the heat sink.
Perform the same procedure
for the other screws.
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and
system board.
Note:
A boxed Intel® processor already includes the CPU fan and heat sink assembly.
If your CPU was purchased separately, make sure to only use Intel®-certified fan
and heat sink.
Heat sink
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of
the CPU. The thermal paste is usually supplied when you purchase the fan / heat sink
assembly. Do not spread the paste all over the surface. When you later place the heat
sink on top of the CPU, the compound will disperse evenly.
“Unlocked” position
of the screw
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel
the strip that covers the paste before you place the fan / heat sink on top of the CPU.
2. Place the heat sink on top
of the CPU. The 4 screw
around the heat sink,
which are used to secure
the heat sink onto the system board, must match the
4 mounting holes around
the socket.
“Locked” position
of the screw
CPU fan connector
CPU fan connector
Mounting hole
5. Connect the CPU fan’s cable
to the CPU fan connector on
the system board.
3. Orient the heat sink such
that the CPU fan’s cable is
nearest the CPU fan connector.
16
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a 3.5" SATA Drive
Installing a 2.5" SATA Drive
1.
Use the same HDD drive tray to secure a 2.5" hard disk to the system. Refer to the pictures below
for the location of mounting holes.
Remove the thumb screws that secure the HDD drive tray to the chassis and remove the
drive tray.
Thumb screw
2.
Secure the hard drive to the drive tray. Align the mounting holes on the SATA drive with the
mounting holes on the HDD drive tray. Use 4 mounting screws to install the hard drive onto
the HDD drive tray.
Mounting screw
Mounting screw
Drive bay
Mounting screw
Mounting screw
17
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing More Than One SATA Drive (Optional)
1. Slide the HDD drive tray back to the system and secure it with the thumb screws.
2. Connect the SATA data cable and power cable to the connectors on the SATA drive. And connect the other end of the SATA data cable on the motherboard.
To install more than one 2.5" SATA drive, use the 5.25" optical drive tray. And to install more than
one 3.5" SATA drive, please order another HDD drive tray as shown in the following procedure.
For 3.5" SATA Drives
SATA data and
power cable
Use the following procedure to install a second 3.5" HDD/SSD:
1.
Secure the hard drive to the drive tray. Align the mounting holes on the SATA drive with the
mounting holes on the HDD drive tray. Use 4 mounting screws to install the hard drive onto
the HDD drive tray.
Mounting screw
Drive bay
Mounting screw
2.
Slide the HDD drive tray with the installed hard drive into the optical drive bay and secure
the installation with the thumb screws.
18
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
For 2.5" SATA Drives
3. Install the optical drive tray back to the system.
Use the following procedure to install a second and third 2.5” HDD/SSD:
4. Connect the SATA data cable and power cable to the connectors on the SATA drive. And connect
the other end of the SATA data cable on the motherboard.
1.
Attach 4 standoffs to the 2.5" HDD or SSD.
SATA data and
power cable
SATA data and
power cable
SATA Port
Mounting screw
Mounting screw
2.
Secure the hard drive to the optical drive tray. Align the standoffs on the HDD with the
mounting holes on the optical drive tray. Use 4 mounting screws to install the hard drive
onto the optical drive tray.
Mounting screw
Mounting screw
19
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a PCI or PCIe Expansion Card
3.
Use the following procedure to install a PCIe expansion card:
Reinstall the card slot bracket to secure the expansion card in place.
1. Remove the mounting screws to uninstall the card slot bracket.
Rear View
Card slot bracket
PCIe card
Screw
2.
Insert the expansion card in the connector on the motherboard and press down until secured.
Notes:
1. The WM343-SD330 is equipped with one PCIe x16, one PCIe x4 and two PCI slots.
2.
The WM343-SD331 is equipped with two PCIe x16 and two PCIe x4 slots.
PCIe card
20
Chapter 3 Installing Devices
www.dfi.com
Chapter 3
Installing a Mini PCIe Card
The system board is equipped with one Mini PCIe slot that uses USB, PCI and mSATA signals.
1.
Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe
card with the notch in the connector on the system board.
2.
Push the Mini PCIe card down and use the provided mounting screws to secure the card on
the system board.
Note:
The Mini PCIe slot is only available in WM343-SD330 (Intel® Q170 Chipset).
21
Chapter 3 Installing Devices
www.dfi.com
Chapter 4
Chapter 4 - Jumper Settings
Clear CMOS
WM343-SD331 (C236/Q170)
WM343-SD330 (Q170)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
1
COM 1 RS232/485
Select (JP8)
6 2
6
1
5 1
6 2
5
6
5 1
5
14 13
Socket LGA1151
COM 1
VGA
System Fan 2
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
1
8
TPM
(optional)
CPU Fan
COM 1 RS232/Power
Select (JP9)
COM 1 RS232/422/485
Select (JP8)
4
5
+12V
Power
Chrontel
CH7517A
IC
2
COM 1 2
RS232/422/485
Select (JP10) 1
1
8
COM 1
VGA
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
CPU Fan
1
System Fan 1
COM 1 RS232/Power
Select (JP9)
Socket LGA1151
21
21
LPC
LPC
ASMedia
ASM1442
12
ASMedia
ASM1442
24
DVI-D
DP++
1
USB 3.0
LAN 2
USB 4
USB 3
Line-out
Mic-in
12
1
2
7
8
1
2
7
8 Header
LAN LED
1
Clear CMOS
Data (JP1)
PCI 1
DDR4_4
Chassis
Intrusion
SPI
Program
PCI 2
2
6
1
5
ITE
IT8893E
LCD/Inverter
Power Select (JP4) 1
1
2
6
5
2
1
(JP13)
USB 9-10 USB 7-8
11
10
9
1
9
1
10
2
10
2
1
9
1
LCD/Inverter Power
SATA 2
10
9
6 2
1
5 1 5 1
(JP12)
1 9
1 9
2 10
COM 2
2
2 10
COM 3
6 2
1
1 9
1
2 10
1
2
Intel
1
2
6 2
6
1
2
5 1
6 2
5
6
10
1
5 1
4
5
System Fan 1
SATA 3
1
21
USB 7-8
11
1 10
6
5
2
1
21
65
COM 2 RS232/422/485
USB 2.0
Select (JP13)
COM 3
USB 9-10 USB 7-8 COM 2
1
9
1
9
1
10
2
10
2 10
9
1
9
2 10
21
5
COM 2 RS232/422/485
Select (JP11)
COM 4
9
2 10
2 10
1 9
1
SMBus
1
2 10
COM 5
2-3 On:
Clear CMOS Data
2
SPI Flash
BIOS
1
SATA 5
System Fan 1
1
6
1 9
1
2
19
Buzzer
1
2
DIO
COM 6
1
1
COM 1 RS232/485
Select (JP8)
If you encounter the following situations, you can reconfigure the system with the default
values stored in the ROM BIOS.
1
5
14 13
+12V
Power
Chrontel
CH7517A
COM 2 RS232/Power
Select (JP14)
PCIe 4 (PCIe x4)
2 3
CPU Fan
COM 1 RS232/Power
Select (JP9)
8
COM 1
VGA
1
SATA 2
Q170
COM 2 RS232/422/485
6 5 Select (JP12) 6 5
Nuvoton
1
NCT6106D
Chassis
Intrusion
System
Fan 2
USB 3.0 11
COM 1 RS232/485
Select (JP10)
1
SATA 1
SATA 4
COM 6
JP1
8
1
SATA 0
PCIe 3 (PCIe x8)
WM343-SD330 (H110)
COM 1
RS232/422/485
Select (JP7)
2
1-2 On: Normal
(default)
DDR4_4
1
S/PDIF
USB 5-6
PS/2 KB/MS
USB 6
USB 5
USB 2.0
12
1
7
DDR4_3
PCIe 2 (PCIe x4)
5
COM 5
11
LAN LED
DDR4_1
DDR4_2
SATA 3
6
SATA 3.0
(JP11)
2 10
COM 4
Clear CMOS
Data (JP1)
1
Realtek
ALC888
2-3 On:
Clear CMOS Data
1
1
1
USB 2.0
USB 5-6
1
2
19
1
40
5
2
SATA 3.0
SATA 1
6
USB 3.0
Digital I/O
39
LVDS LCD Panel
SMBus
Battery
2 3
1
Front
Panel
Intel
WGI210AT
PCIe 1 (PCIe x16 or PCIe x8)
SATA 0
COM 2 RS232/Power
Select (JP14)
PCIe x4
1
USB 3.0
1
13
1
Auto Power-on
Select (JP5)
1
Q170
Panel Power Select (JP2)
1
USB 3.0
Line-out
Mic-in
1
Nuvoton
NCT6106D
Intel
WGI219LM
LAN 2
USB 4
USB 3
JP1
1
Buzzer
2
SPI Flash
BIOS
DDR4_3
DDR4_2
Intel
S/PDIF
Backlight Power
Select (JP3)
DDR4_1
Mini PCIe/mSATA 1
Signal Select (JP6)
Realtek
ALC888
NXP
PTN3460
11
Battery
PCIe x16
1
1-2 On: Normal
(default)
2
Front
Panel
Intel
WGI210AT
USB 3.0
1 2 3
ATX
Power
LAN 1
USB 2
USB 1
13
Auto Power-on 1
Select (JP5) 1
24
Standby
Power LED
1 2 3
Standby
Power LED
Intel
WGI219LM
12
DVI-D
DP++
ATX
Power
LAN 1
USB 2
USB 1
TPM
(optional)
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
24
DVI-D
DP++
ATX
Power
Standby
Power LED
Intel
WGI219LM
3
LAN 2
USB 4
USB 3
1
2
1
1
PCI 2
1
1
JP3
2
5
H110
PCIe x4
1
39
2
40
LVDS LCD Panel
1
19
LCD/Inverter Power
SMBus
1
1
4
6
2
SATA 2
1
6
5
2
1
(JP13)
USB 7-8
USB 9/10
1
2
9
1
10
2
1
1
9
3. Now plug the power cord and power on the system.
2 3
2-3 On:
Clear CMOS Data
SATA 1
5
USB 2.0
Digital I/O
SW1
1
Nuvoton
NCT6106D
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper pins back
to its default setting, pins 1 and 2 On.
SATA 0
COM 2 RS232/Power
Select (JP14)
6
JP4
JP2
JP1
1. Power off the system and unplug the power cord.
1-2 On: Normal
(default)
1
1
S/PDIF
To load the default values stored in the ROM BIOS, please follow these steps below:
J6
Chassis
Intrusion
Intel
Buzzer
1
8
7
SPI Flash
BIOS
DDR4_3
1
2
2
7
8
DDR4_1
PCI 1
ON
4
12
1
JP6
1
Clear CMOS
Data (JP1)
Realtek
ALC888
3
11
LAN LED
Battery
PCIe x16
R507 R505
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
1
1 2 3
Auto Power-on 1
Select (JP5) 1
J26
USB 3.0
13
1
1
LAN 1
USB 2
USB 1
9
1 9
(JP12)
2
6 2
1
5 1 5 1
1 9
6 2
6
SATA 3
SATA 3.0
(JP11)
5
1 9
1
1
10
2 10
COM 2
2 10
COM 3
2 10
COM 4
2 10
COM 5
2
COM 6 System
Fan 2
22
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Serial Port RS232/422/485 Select
WM343-SD330 (Q170)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
JP7,
JP10, JP8
CPU Fan
System Fan 1
COM 1 RS232/Power
Select (JP9)
1
1
COM 1 RS232/485
Select (JP8)
5
TPM
(optional)
14 13
+12V
Power
Chrontel
CH7517A
1 3 5
1
8
COM 1
VGA
JP7, JP8, and JP10 (for COM 1) and JP11, JP12, and JP13 (for COM 2) are used to configure
the COM ports to RS232, RS422 (full duplex) or RS485. The pin assignments of the COM ports
will vary according to the jumper settings.
2 4 6
Socket LGA1151
JP7 (COM 1) / JP11 (COM 2)
21
LPC
ASMedia
ASM1442
12
2 4 6
2 4 6
24
DVI-D
DP++
2 4 6
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
USB 3.0
Intel
WGI210AT
USB 3.0
11
12
1
2
7
8
1
2
7
8 Header
LAN LED
Battery
1
Clear CMOS
Data (JP1)
PCIe x16
Realtek
ALC888
DDR4_2
DDR4_4
Chassis
Intrusion
1 3 5
1 3 5
1 3 5
1-2 On: RS232
(default)
3-4 On: RS422
Full Duplex
5-6 On: RS485
SPI
Program
JP8 and JP10 (COM 1) / JP12 and JP13 (COM 2)
1
Nuvoton
NCT6106D
1
SATA 0
1
PCI 2
Q170
2
6
1
5
SATA 1
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
PCIe x4
1
ITE
IT8893E
LCD/Inverter
Power Select (JP4) 1
1
2
DDR4_3
Intel
S/PDIF
Buzzer
Backlight Power
Select (JP3)
DDR4_1
SPI Flash
BIOS
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
NXP
PTN3460
2
Front
Panel
Line-out
Mic-in
1
13
Auto Power-on 1
Select (JP5) 1
LAN 2
USB 4
USB 3
40
LVDS LCD Panel
SMBus
USB 5-6
9
1
9
1
10
2
10
2
1
6
2
LCD/Inverter Power
1
9
10
5
2
1
9
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
1 9
2 10
COM 2
JP13, JP12, JP11
SATA 2
1
6
(JP13)
USB 9-10 USB 7-8
11
10
1
2
19
1
1
USB 2.0
USB 3.0
Digital I/O
39
5
2 10
COM 3
2 10
COM 4
SATA 3
SATA 3.0
(JP11)
1 9
1
2 10
COM 5
System
Fan 2
1
2
2 4 6
1 3 5
COM 6
2 4 6
2 4 6
1 3 5
1 3 5
3-5, 4-6 On:
RS422 Full Duplex/ RS485
1-3, 2-4 On: RS232
(default)
WM343-SD330 (H110)
COM 1
6
1
2
5 1
6 2
5
6
1
5 1
4
5
1
1
1
5
14 13
+12V
Power
Chrontel
CH7517A
System Fan 1
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
JP7,
JP10, JP8
CPU Fan
COM 1 RS232/Power
Select (JP9)
Socket LGA1151
TPM
(optional)
1 3 5
12 3 4 5
DATA+
DATAN.C.
N.C.
GND
COM 1 RS232/485
Select (JP10)
6 2
RXD+
RXDTXD+
TXDGND
2
DCD
RXD
TXD
DTR
GND
2 4 6
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1 2 3 4 5
1 2 3 4 5
6 7 8 9
6 7 8 9
6 7 8 9
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
1
1
1
JP3
2
5
PCIe x4
1
39
Nuvoton
NCT6106D
40
LVDS LCD Panel
1
19
LCD/Inverter Power
SMBus
5
6
1
2
USB 7-8
USB 9/10
1
2
4
9
1
10
2
1
1
9
9
JP13, JP12, JP11
SATA 2
1
6
5
2
1
(JP13)
USB 2.0
Digital I/O
SW1
2
SATA 1
COM 2 RS232/Power
Select (JP14)
6
JP4
JP2
1
1 9
(JP12)
2
6 2
6 2
1
5 1 5 1
1 9
SATA 3
6
SATA 3.0
(JP11)
5
1 9
1
1
10
2 10
COM 2
2 10
COM 3
2 10
COM 4
2 10
COM 5
2
COM 6 System
Fan 2
1
2
1 3 5
ON
RS232
N.C.
N.C.
N.C.
N.C.
RS485
NC.
NC.
NC.
TXD+
RXD+
9
10
2 4 6
9
10
1
2
NC.
NC.
NC.
TXDRXD-
RI
RTS
GND
TXD
SATA 0
H110
CTS
DSR
DTR
RXD
PCI 2
DCD
1
1
S/PDIF
RS422
Full Duplex
COM 2
RS422
Full Duplex
NC.
NC.
NC.
NC.
DATA+
2
Chassis
Intrusion
Intel
Buzzer
1
1
DDR4_3
J6
DDR4_1
1
Realtek
ALC888
2
RS232
8
7
Clear CMOS
Data (JP1)
1
4
2
7
SPI Flash
BIOS
JP6
1
PCI 1
3
12
1
LAN LED
Battery
PCIe x16
R507 R505
11
8
Line-out
Mic-in
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
N.C.
N.C.
N.C.
N.C.
1
3
LAN 2
USB 4
USB 3
13
1
Auto Power-on 1
Select (JP5) 1
J26
USB 3.0
DSR
RTS
CTS
RI
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
9
10
1
2
NC.
NC.
NC.
DATA-
ATX
Power
RS485
23
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
WM343-SD331 (C236/Q170)
JP7 (COM 1) / JP11 (COM 2)
2 4 6
IC
6 2
6
1
5 1
6 2
5
6
5 1
5
4
System Fan 2
Chrontel
CH7517A
1 3 5
5
14 13
+12V
Power
Socket LGA1151
TPM
(optional)
6 5
2 4 6
JP7,
JP10, JP8
1
1
1
8
COM 1
VGA
CPU Fan
COM 1 RS232/Power
Select (JP9)
COM 1 RS232/422/485
Select (JP8)
1 3 5
2 4 6
6
5
2
1
1 3 5
2 1
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
Standby
Power LED
Intel
WGI219LM
USB 3.0
1
Battery
Line-out
Mic-in
Clear CMOS
Data (JP1)
1
1
2
6 5
11
12
1
2
1 3 5
2 1
LAN LED
DDR4_1
PCIe 1 (PCIe x16 or PCIe x8)
7
DDR4_3
DDR4_2
8
DDR4_4
SATA 3.0
PCIe 2 (PCIe x4)
1
SATA 0
1
SATA 2
Q170
SATA 3
SATA 4
6 5
1 3 5
2
9
1
9
1
10
2
10
2 10
9
1
9
2 10
COM 2 RS232/422/485
Select (JP11)
COM 4
5
1
6
2
1
2 10
2 10
9
1 9
1
2 10
2
COM 5
19
12 3 4 5
1 2 3 4 5
1 2 3 4 5
6 7 8 9
6 7 8 9
6 7 8 9
1
SMBus
SPI Flash
BIOS
1 9
COM 1
System Fan 1
DATA+
DATAN.C.
N.C.
GND
1
21
JP12, JP13, JP11
N.C.
N.C.
N.C.
N.C.
65
SATA 5
Buzzer
1
2
DIO
1
RXD+
RXDTXD+
TXDGND
21
COM 2 RS232/422/485
USB 2.0
Select (JP13)
COM 3
USB 9-10 USB 7-8 COM 2
USB 7-8
11
1 10
2 4 6
N.C.
N.C.
N.C.
N.C.
21
1
2 1
COM 6
JP7, JP8, and JP10 (for COM1) and JP11, JP12, and JP13 (for COM2) are used to configure the
COM ports to RS232, RS422 (full duplex) or RS485. The pin assignments of the COM ports will
vary according to the jumper settings.
RS422
Full Duplex
COM 2
9
10
DCD
RI
RTS
GND
TXD
RS232
CTS
DSR
DTR
RXD
1
2
RS232
RS485
NC.
NC.
NC.
TXD+
RXD+
PCIe 4 (PCIe x4)
USB 5-6
10
1
COM 2 RS232/422/485
6 5 Select (JP12) 6 5
6
5
COM 2 RS232/Power
Select (JP14)
2
1
6 5
1
9
10
1
2
NC.
NC.
NC.
TXDRXD-
PCIe 3 (PCIe x8)
USB 3.0 11
5-6 On: RS485
3-5, 4-6 On:
RS422 Full Duplex/ RS485
1-3, 2-4 On: RS232
(default)
SATA 1
Intel
S/PDIF
Nuvoton
1
NCT6106D
Chassis
Intrusion
1
DCD
RXD
TXD
DTR
GND
1
1
DSR
RTS
CTS
RI
Realtek
ALC888
2
Front
Panel
Intel
WGI210AT
USB 3.0
2 4 6
13
1
Auto Power-on
Select (JP5)
LAN 2
USB 4
USB 3
5
JP8 and JP10 (COM 1) / JP12 and JP13 (COM 2)
ATX
Power
LAN 1
USB 2
USB 1
6
1 3 5
3-4 On: RS422
Full Duplex
1-2 On: RS232
(default)
24
2 4 6
RS422
Full Duplex
NC.
NC.
NC.
TXD
DATA+
2
COM 1 2
RS232/422/485
Select (JP10) 1
9
10
1
2
NC.
NC.
NC.
DATA-
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
RS485
24
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Serial Port Power Select
WM343-SD331 (C236/Q170)
WM343-SD330 (Q170)
2 4 6
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
1
5
Chrontel
CH7517A
1 3 5
1
14 13
+12V
Power
Socket LGA1151
TPM
(optional)
COM 1
RS232/422/485
Select (JP7)
2
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
2 4 6
JP9
CPU Fan
1
System Fan 1
COM 1 RS232/Power
Select (JP9)
1
COM 1 2
RS232/422/485
Select (JP10) 1
12
5
Intel
WGI219LM
5
1
Intel
WGI210AT
USB 3.0
21
12
1
2
7
8
Clear CMOS
Data (JP1)
1
2
7
8 Header
SPI Flash
BIOS
DDR4_3
DDR4_2
DDR4_4
Chassis
Intrusion
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
Realtek
ALC888
USB 3.0
SPI
Program
Q170
1
Panel Power Select (JP2)
5
PCIe x4
1
ITE
IT8893E
LCD/Inverter
Power Select (JP4) 1
1
39
2
40
LVDS LCD Panel
USB 5-6
1
2
6
2
6
5
2
1
(JP13)
USB 9-10 USB 7-8
11
10
9
1
9
1
LCD/Inverter Power
10
2
10
2
1
9
1
10
9
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
1 9
2 10
COM 2
JP14
1
USB 2.0
USB 3.0
Digital I/O
19
1
SMBus
1
2 10
COM 3
2 10
COM 4
SATA 3
SATA 3.0
(JP11)
1 9
1
2 10
COM 5
1
2
1
COM 6
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
PCIe 4 (PCIe x4)
21
2 4 6
USB 7-8
11
1 10
5
14 13
Socket LGA1151
TPM
(optional)
1 3 5
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
1
9
1
2
10
2 10
9
1
9
2 10
COM 4
System Fan 1
1
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
COM 5
2
JP14
1
SMBus
6
19
Buzzer
1
2
2 1
DIO
COM 6
Standby
Power LED
Intel
WGI219LM
13
1
1
Auto Power-on 1
Select (JP5) 1
3
J26
USB 3.0
2
Front
Panel
12
1
2
6 7 8 9
LAN LED
8
J6
2
7
SPI Flash
BIOS
DDR4_3
1
PCIe x16
DDR4_1
Chassis
Intrusion
JP6
1
Clear CMOS
Data (JP1)
7
Battery
8
Line-out
Mic-in
11
1
1
PCI 1
Realtek
ALC888
2 4 6
1
Intel
SATA 0
1
S/PDIF
PCI 2
H110
2
1
1
PCIe x4
1
39
Nuvoton
NCT6106D
40
LVDS LCD Panel
1
19
LCD/Inverter Power
SMBus
5
1
6
2
1
USB 7-8
USB 9/10
1
2
4
9
1
10
2
1
1
9
9
JP14
SATA 2
1
6
5
2
1
(JP13)
USB 2.0
Digital I/O
SW1
2
SATA 1
COM 2 RS232/Power
Select (JP14)
6
5
JP4
JP2
1
JP3
Buzzer
1 9
(JP12)
2
6 2
6 2
1
5 1 5 1
1 9
6
1 3 5
SATA 3
SATA 3.0
(JP11)
5
1 9
2 10
COM 2
2 10
COM 3
2 10
COM 4
2 10
COM 5
2
COM 6 System
Fan 2
5
2 1
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
1
1
10
6
6 5
2 1
DSR
RTS
CTS
RI
(or 5V)
Intel
WGI210AT
USB 3.0
1
9
10
5
COM 2 RS232/422/485
Select (JP11)
SATA 5
12 3 4 5
ATX
Power
LAN 2
USB 4
USB 3
1
21
1
JP9 (for COM1) and JP14 (for COM2) are used to switch the COM ports to RS232 or RS232
with power. The pin assignments of the COM ports will vary according to the jumper settings.
21
LAN 1
USB 2
USB 1
65
21
COM 2 RS232/422/485
USB 2.0
Select (JP13)
COM 3
USB 9-10 USB 7-8 COM 2
6 5
SATA 3
1
1
+12V
Power
Chrontel
CH7517A
Q170
COM 2 RS232/422/485
6 5 Select (JP12) 6 5
6
5
COM 2 RS232/Power
Select (JP14)
2
1
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
JP9
1
SATA 1
1
SATA 2
SATA 4
Nuvoton
1
NCT6106D
Chassis
Intrusion
CPU Fan
1
1
SATA 0
1
10
System Fan 1
1
S/PDIF
USB 3.0 11
COM 1 RS232/Power
Select (JP9)
8
DCD
(or 12V)
RXD
TXD
DTR
GND
COM 1 RS232/485
Select (JP10)
2
2
7
DDR4_4
Intel
USB 5-6
COM 1
RS232/422/485
Select (JP7)
1
DDR4_3
DDR4_2
PCIe 2 (PCIe x4)
2 1
System
Fan 2
12
LAN LED
DDR4_1
PCIe 3 (PCIe x8)
WM343-SD330 (H110)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
Clear CMOS
Data (JP1)
1
Realtek
ALC888
1
SATA 2
2
11
SATA 3.0
SATA 1
5
Battery
PCIe 1 (PCIe x16 or PCIe x8)
6 5
1
Front
Panel
Intel
WGI210AT
Line-out
Mic-in
SATA 0
COM 2 RS232/Power
Select (JP14)
6
1
USB 3.0
1
13
1
Auto Power-on
Select (JP5)
LAN 2
USB 4
USB 3
1
PCI 2
2
Intel
WGI219LM
1
Nuvoton
NCT6106D
Intel
Buzzer
Backlight Power
Select (JP3)
DDR4_1
24
ATX
Power
LAN 1
USB 2
USB 1
2
LAN LED
1
S/PDIF
12
Standby
Power LED
13
11
Battery
PCIe x16
2
TPM
(optional)
LPC
Front
Panel
Line-out
Mic-in
ON
4
14 13
Socket LGA1151
DVI-D
DP++
Auto Power-on 1
Select (JP5) 1
LAN 2
USB 4
USB 3
3
1 3 5
1
Standby
Power LED
USB 3.0
R507 R505
System Fan 2
COM 1 RS232/422/485
Select (JP8)
ASMedia
ASM1442
LAN 1
USB 2
USB 1
1
1
1
24
ATX
Power
NXP
PTN3460
5
6
5 1
+12V
Power
Chrontel
CH7517A
DVI-D
DP++
1
5 1
6 2
CPU Fan
COM 1 RS232/Power
Select (JP9)
8
COM 1
VGA
21
ASMedia
ASM1442
6
4
LPC
JP9
IC
6 2
RS232
2 4 6
6
5
1 3 5
2 1
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
25
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Power-on Select
WM343-SD331 (C236/Q170)
WM343-SD330 (Q170)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
6 2
6
1
COM 1 2
5 1
6 2
5
6
5 1
5
RS232/422/485
Select (JP10) 1
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
COM 1
VGA
COM 1 RS232/485
Select (JP8)
1
5
14 13
+12V
Power
Socket LGA1151
System Fan 2
1
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
COM 1 RS232/422/485
Select (JP8)
8
1
1
System Fan 1
COM 1 RS232/Power
Select (JP9)
CPU Fan
COM 1 RS232/Power
Select (JP9)
4
2
Chrontel
CH7517A
IC
2
CPU Fan
8
COM 1
VGA
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
Socket LGA1151
TPM
(optional)
TPM
(optional)
21
LPC
ASMedia
ASM1442
21
LPC
ASMedia
ASM1442
12
12
DVI-D
DP++
24
DVI-D
DP++
24
Standby
Power LED
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
USB 3.0
LAN 2
USB 4
USB 3
Line-out
Mic-in
12
1
2
Battery
1
Clear CMOS
Data (JP1)
Realtek
ALC888
DDR4_4
8
1
2
7
8 Header
Chassis
Intrusion
SPI
Program
Nuvoton
NCT6106D
1
Battery
Line-out
Mic-in
Clear CMOS
Data (JP1)
1
1
1 2 3
11
12
1
2
LAN LED
DDR4_1
PCIe 1 (PCIe x16 or PCIe x8)
SATA 0
JP5
2
Front
Panel
Intel
WGI210AT
USB 3.0
1
7
DDR4_3
DDR4_2
8
DDR4_4
1
S/PDIF
PCI 2
2
6
Q170
1
5
SATA 1
PCIe x4
1
ITE
IT8893E
1
Digital I/O
39
1
2
19
1
40
LVDS LCD Panel
SMBus
5
6
USB 2.0
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
1
9
1
LCD/Inverter Power
SATA 2
10
2
6
5
2
1
9
2
6 2
1
5 1 5 1
(JP12)
1 9
1 9
2 10
COM 2
Realtek
ALC888
1
1
(JP13)
USB 3.0
USB 5-6
11
10
SATA 3.0
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
LCD/Inverter
Power Select (JP4) 1
2 10
COM 3
6 2
SATA 3
6
SATA 3.0
(JP11)
5
1 9
2 10
COM 4
1
2 10
COM 5
1
2
1
System
Fan 2
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
COM 6
1
SATA 2
Q170
SATA 3
SATA 4
WM343-SD330 (H110)
1
Nuvoton
NCT6106D
21
Chassis
Intrusion
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
9
1
9
1
10
2
10
2 10
9
1
9
2 10
21
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
COM 5
1
SMBus
6
COM 4
SATA 5
System Fan 1
1
2
19
Buzzer
1
2
DIO
COM 6
1
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
1
21
5
COM 2 RS232/422/485
Select (JP11)
1
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
System Fan 1
11
1 10
10
CPU Fan
COM 1 RS232/Power
Select (JP9)
65
COM 2 RS232/422/485
USB 2.0
Select (JP13)
COM 3
USB 9-10 USB 7-8 COM 2
USB 7-8
USB 3.0 11
COM 1
RS232/422/485
Select (JP7)
1
COM 2 RS232/422/485
6 5 Select (JP12) 6 5
6
5
COM 2 RS232/Power
Select (JP14)
2
1
PCIe 4 (PCIe x4)
USB 5-6
PS/2 KB/MS
USB 6
USB 5
USB 2.0
13
1
Auto Power-on
Select (JP5)
LAN 2
USB 4
USB 3
1
Intel
Buzzer
2
SPI Flash
BIOS
DDR4_3
DDR4_2
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
Backlight Power
Select (JP3)
DDR4_1
7
Intel
WGI219LM
USB 3.0
2
11
ATX
Power
LAN 1
USB 2
USB 1
1 2 3
LAN LED
PCIe x16
NXP
PTN3460
JP5
Front
Panel
Intel
WGI210AT
USB 3.0
1
13
Auto Power-on 1
Select (JP5) 1
Socket LGA1151
TPM
(optional)
JP5 is used to select the method of powering on the system. If you want the system to
power on whenever AC power comes in, set the jumper pins 2 and 3 to On. If you want to use
the power button, set the jumper pins 1 and 2 to On.
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
Standby
Power LED
Intel
WGI219LM
Auto Power-on 1
Select (JP5) 1
3
J26
USB 3.0
LAN 2
USB 4
USB 3
Intel
WGI210AT
1
2
J6
Chassis
Intrusion
1
PCI 2
SATA 0
H110
1
1
JP3
2
6
5
PCIe x4
1
39
2
40
LVDS LCD Panel
1
19
LCD/Inverter Power
SMBus
5
1
6
2
USB 7-8
USB 9/10
1
2
4
9
1
10
2
1
1
9
9
5
2
1
1 9
(JP12)
2
6 2
1
5 1 5 1
1 9
6 2
6
SATA 3
SATA 3.0
(JP11)
5
1 9
2 10
COM 2
3
2-3 On:
Power-on via AC power or
WOL after power interruption
1
1
10
2
SATA 2
1
6
(JP13)
USB 2.0
Digital I/O
SW1
1
Nuvoton
NCT6106D
1
SATA 1
1
COM 2 RS232/Power
Select (JP14)
JP4
JP2
3
1
1
S/PDIF
2
1-2 On:
Power-on via power button
(default)
8
1
7
SPI Flash
BIOS
DDR4_3
Intel
Buzzer
1
2
7
DDR4_1
PCI 1
Realtek
ALC888
2
12
1
JP6
1
Clear CMOS
Data (JP1)
1
ON
4
1 2 3
LAN LED
Battery
PCIe x16
3
11
8
Line-out
Mic-in
R507 R505
JP5
2
Front
Panel
USB 3.0
1
13
1
1
LAN 1
USB 2
USB 1
2 10
COM 3
2 10
COM 4
2 10
COM 5
2
COM 6 System
Fan 2
26
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Backlight Power Select (for SD330-Q170/H110 only)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
Panel Power Select (for SD330-Q170/H110 only)
Socket LGA1151
COM 1 RS232/485
Select (JP10)
TPM
(optional)
Intel
WGI210AT
Clear CMOS
Data (JP1)
PCIe x16
Realtek
ALC888
12
1
2
7
8
1
2
PCI 2
5
DDR4_2
DDR4_4
1
PCIe x4
ITE
IT8893E
Digital I/O
39
1
LVDS LCD Panel
19
1
2
SMBus
USB 2.0
USB 5-6
USB 9-10 USB 7-8
11
10
LCD/Inverter Power
5
1
6
2
6
5
2
1
9
1
9
1
10
2
10
2
1
1
9
10
9
2 10
COM 2
1 9
2 10
COM 3
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
Backlight Power
Select (JP3)
2 10
COM 4
1 9
1
2 10
COM 5
NXP
PTN3460
2
1
System
Fan 2
2
DDR4_4
Chassis
Intrusion
7
8
1
2
7
8 Header
SPI
Program
1
Nuvoton
NCT6106D
1
SATA 0
1
2
SATA 3
SATA 3.0
(JP11)
12
1
SPI Flash
BIOS
DDR4_3
DDR4_2
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 2
SATA 1
SATA 2
DDR4_1
Intel
S/PDIF
1
(JP13)
USB 3.0
1
Clear CMOS
Data (JP1)
Q170
Buzzer
1
11
Battery
Realtek
ALC888
SATA 0
2
Front
Panel
PCIe x16
1
13
LAN LED
PCI 1
Nuvoton
NCT6106D
24
Standby
Power LED
Line-out
Mic-in
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
12
Intel
WGI210AT
SPI
Program
8 Header
7
Chassis
Intrusion
Q170
40
TPM
(optional)
1
USB 3.0
1
LCD/Inverter
Power Select (JP4) 1
2
SPI Flash
BIOS
DDR4_3
Intel
Buzzer
1
DDR4_1
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
1
14 13
Socket LGA1151
Auto Power-on 1
Select (JP5) 1
LAN 2
USB 4
USB 3
LAN LED
1
1
5
USB 3.0
2
11
Battery
Backlight Power
Select (JP3)
1
+12V
Power
Intel
WGI219LM
LAN 1
USB 2
USB 1
13
Front
Panel
Line-out
Mic-in
NXP
PTN3460
1
ATX
Power
Auto Power-on 1
Select (JP5) 1
6
5
DVI-D
DP++
1
USB 3.0
2
5 1
4
1
COM 1 RS232/485
Select (JP8)
ASMedia
ASM1442
Standby
Power LED
Intel
WGI219LM
S/PDIF
1
CPU Fan
System Fan 1
COM 1 RS232/Power
Select (JP9)
21
24
ATX
Power
1
5
6
LPC
12
DVI-D
DP++
USB 3.0
6
5 1
6 2
Chrontel
CH7517A
LPC
ASMedia
ASM1442
LAN 2
USB 4
USB 3
6 2
1
2
8
COM 1
VGA
21
LAN 1
USB 2
USB 1
2
1
1
6
5
SATA 1
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
PCIe x4
ITE
IT8893E
LCD/Inverter
Power Select (JP4) 1
1
39
2
40
LVDS LCD Panel
19
USB 5-6
1
2
11
10
LCD/Inverter Power
1
6
2
SATA 2
1
6
5
2
1
(JP13)
USB 2.0
USB 3.0
Digital I/O
1
SMBus
5
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
1
1
9
10
9
2 10
COM 2
1 9
2 10
COM 3
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
2 10
COM 4
SATA 3
SATA 3.0
(JP11)
1 9
1
2 10
COM 5
2
1
System
Fan 2
COM 6
JP2
COM 6
JP3
2 4 6
3
2
1
1 3 5
JP2 is used to select the power supply of the LCD panel.
JP3 is used to select the power level of backlight brightness control.
Panel Power Select
Backlight Power Select
JP2
JP3
+12V
1-2 On
+3.3V (default)
1-2 On
+5V
3-4 On
+5V
2-3 On
+3.3V (default)
5-6 On
27
Chapter 4 Jumper Settings
www.dfi.com
Chapter 4
Mini PCIe/mSATA Signal Select (for SD330-Q170 only)
LCD/Inverter Power Select (for SD330-Q170/H110 only)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
1
5
14 13
+12V
Power
Chrontel
CH7517A
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1
1
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
COM 1
RS232/422/485
Select (JP7)
CPU Fan
System Fan 1
COM 1 RS232/Power
Select (JP9)
Socket LGA1151
CPU Fan
COM 1
VGA
1
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
COM 1 RS232/485
Select (JP8)
8
TPM
(optional)
System Fan 1
COM 1 RS232/Power
Select (JP9)
Socket LGA1151
21
21
LPC
LPC
ASMedia
ASM1442
12
ASMedia
ASM1442
24
12
ATX
Power
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
USB 3.0
Intel
WGI210AT
Line-out
Mic-in
11
12
1
2
7
8
1
2
1
Clear CMOS
Data (JP1)
PCIe x16
Realtek
ALC888
DDR4_2
DDR4_4
7
Chassis
Intrusion
Line-out
Mic-in
SPI
Program
8 Header
Nuvoton
NCT6106D
PCI 2
Q170
1
2
1
6
5
1
PCIe x4
ITE
IT8893E
Digital I/O
39
1
40
LVDS LCD Panel
19
1
2
11
10
SMBus
5
6
2
6
5
2
1
(JP13)
USB 3.0
USB 2.0
USB 5-6
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
1
LCD/Inverter Power
1
1
9
10
9
2 10
COM 2
1 9
2 10
COM 3
PCI 2
2
2
6 2
1
5 1 5 1
(JP12)
1 9
6 2
2 10
COM 4
Backlight Power
Select (JP3)
SATA 3
6
SATA 3.0
(JP11)
NXP
PTN3460
5
1 9
1
2 10
COM 5
2
1
System
Fan 2
2
1
1
6
DDR4_4
8
1
2
7
8 Header
Chassis
Intrusion
SPI
Program
1
Nuvoton
NCT6106D
1
SATA 0
5
SATA 1
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
PCIe x4
ITE
IT8893E
Digital I/O
39
1
40
LVDS LCD Panel
19
1
2
LCD/Inverter Power
11
10
SMBus
5
1
6
2
SATA 2
1
6
5
2
1
(JP13)
USB 3.0
USB 2.0
USB 5-6
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
1
1
9
10
9
2 10
COM 2
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
1 9
2 10
COM 3
2 10
COM 4
SATA 3
SATA 3.0
(JP11)
1 9
1
2 10
COM 5
2
1
System
Fan 2
COM 6
JP6
JP4
Mini PCIe Socket
1 2 3
1 2 3
JP4 is used to select the power level of the LCD/inverter power connector.
LCD/Inverter Power Select
DDR4_2
Q170
LCD/Inverter
Power Select (JP4) 1
1
COM 6
7
1
S/PDIF
SATA 2
1
2
SPI Flash
BIOS
DDR4_3
Intel
Buzzer
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
LCD/Inverter
Power Select (JP4) 1
1
SATA 1
DDR4_1
Mini PCIe/mSATA 1
Signal Select (JP6)
Realtek
ALC888
1
S/PDIF
12
1
LAN LED
1
Clear CMOS
Data (JP1)
PCI 1
SATA 0
11
Battery
PCIe x16
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
1
Intel
Buzzer
2
SPI Flash
BIOS
DDR4_3
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
Backlight Power
Select (JP3)
DDR4_1
13
Auto Power-on 1
Select (JP5) 1
LAN 2
USB 4
USB 3
LAN LED
Battery
1
USB 3.0
2
Front
Panel
USB 3.0
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
13
Auto Power-on 1
Select (JP5) 1
LAN 2
USB 4
USB 3
NXP
PTN3460
24
DVI-D
DP++
DVI-D
DP++
1
TPM
(optional)
JP6 is used to select the signal for the Mini PCIe socket.
JP4
+12V (default)
1-2 On
+5V
2-3 On
Mini PCIe/mSATA Signal Select
JP6
Mini PCIe (default)
1-2 On
mSATA
2-3 On
28
Chapter 4 Jumper Settings
www.dfi.com
Chapter 5
Chapter 5 - Ports and Connectors
Rear Panel I/O Ports
COM 1
PS/2 Keyboard/Mouse Port
DVI
LAN 1 LAN 2
PS/2 Keyboard/Mouse
PS/2 KB/MS
Line-out
USB 2.0
Mic-in
VGA
DP++
USB 3.0
These ports are used to connect a PS/2 mouse/keyboard.
The rear panel I/O consists of the following ports:
Wake-On PS/2 Keyboard/Mouse
•
•
•
•
•
•
•
•
•
•
•
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power on the system. To use this function, configure the wake-up function of PS/2
keyboard/mouse in the Advanced menu (“ACPI Configuration” submenu) of the BIOS. Refer to
Chapter 7 for more information.
1 PS/2 Keyboard/Mouse port
1 Serial port
1 VGA
1 DVI-I (DVI-D Signal) port
1 DisplayPort
2 RJ45 LAN ports
4 USB 3.0 ports
2 USB 2.0 ports
Line-in jack (optional)
Line-out jack
Microphone jack
Note:
This port cannot work with a PS/2 mouse alone. To connect both keyboard and
mouse, please use a PS/2 keyboard mouse splitter cable adapter.
29
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
COM (Serial) Ports
Graphics Interfaces
The display ports consist of the following:
•
•
•
DVI-I port (DVI-D signal)
1 DP++ port
1 VGA port
DVI-I
(DVI-D Signal)
DVI
LAN 1
LAN 2
Line-out
Mic-in
VGA
COM 1
DP
COM 1 port
VGA Port
The pin functions of COM 1 will vary according to the respective jumper settings (JP7, JP8 and
JP10). Another jumper (JP9) is used to configure COM 1 to pure RS232 or RS232 with power.
Refer to “Serial Port RS232/422/485 Select” and “Serial Port Power Select” in Chapter 4 for
more information.
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell
cable connector to the VGA port. After you plug the monitor’s cable connector into the VGA
port, gently tighten the cable screws to hold the connector in place.
DVI-I Port
COM 3 to COM 6 are fixed at RS232.
The DVI-I (DVI-D Signal) port is used to connect an LCD monitor. Having a DVI-I interface,
this port supports DVI-D signal only. Connect the display device’s cable connector to the
DVI-I port. After plugging the cable connector into the port, gently tighten the cable screws
to hold the connector in place.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
BIOS Setting
DP Port
Configure the serial ports in the Advanced menu (“SIO NUVOTON6106D” submenu) of the
BIOS. Refer to Chapter 7 for more information.
The DisplayPort is a digital display interface used to connect a display device. The interface, developed by VESA and backwards compatible with VGA, DVI and HDMI, delivers
higher performance than any other digital interfaces.
BIOS Setting
Configure display devices in the advanced menu (“Video Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
30
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
RJ45 LAN Ports
USB Ports
LAN 1
LAN 2
USB 3.0
USB 3.0
USB 2
USB 1
USB 4
USB 3
Features
•
•
LAN1: Intel® I219LM Gigabit Ethernet controller with iAMT11.0. (Note that SKUs with the
Intel® H110 chipset or the Intel® Core™ i3, Celeron® and Pentium® processors do not support iAMT.)
USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
LAN2: Intel® I210AT PCI Express Gigabit Ethernet controller
In addition to the external USB ports, the system board is equipped with onboard USB 3.0 and
2.0 pin headers. Refer to “I/O Connectors” in this chapter for more information.
The LAN ports allow the system board to connect to a local area network with a network hub.
Wake-On-USB Keyboard/Mouse
BIOS Setting
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function, make
sure that that the +5V_standby power source of your power supply must support ≥1.5A for
2 USB ports. For 3 or more USB ports, the +5V_standby power source of your power supply
must support ≥2A.
Configure the onboard LAN ports in the Advanced menu (“ACPI Configuration” submenu) of
the BIOS. Refer to Chapter 7 for more information.
Driver Installation
Install the LAN drivers. Refer to Chapter 8 for more information.
BIOS Setting
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to Chapter 7 for more information.
Driver Installation
You may need to install the proper drivers in your operating system to use USB devices. Refer
to Chapter 8 and your operating system’s manual or documentation for more information.
31
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Audio
Line-out
Mic-in
Rear Audio
The system board is equipped with 2 audio jacks. A jack is a one-hole connecting interface for
inserting a plug.
•
Line-out Jack (lime)
This jack is used to connect a headphone or external speakers.
•
Mic-in Jack (pink)
This jack is used to connect an external microphone.
Driver Installation
Install the audio driver. Refer to Chapter 8 for more information.
32
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
I/O Connectors
S/PDIF Connector
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
SD330-Q170/H110
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
Line-out
Mic-in
2
11
12
1
2
7
8
1
2
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
SPDIF out
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
NC Ground
SPDIF in
+5V
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
1
Intel
SATA 0
1
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
5
1
2
6
1
5
1
NXP
PTN3460
2
SATA 2
PCIe x4
ITE
IT8893E
1
39
1
5
1
Front
Panel
Intel
WGI210AT
USB 3.0
1
13
1
USB 3.0
LAN 2
USB 4
USB 3
1
24
DVI-D
DP++
Digital I/O
1
40
LVDS LCD Panel
SMBus
USB 3.0
(only for Q170)
USB 5-6
11
10+
1
2
19
USB 2.0
USB 9-10 USB 7-8
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
5
1
6
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
6 2
6
1
5 1
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis and connect the audio cable to the S/PDIF connector. Make sure pin 1 of
the audio cable is aligned with pin 1 of the S/PDIF connector.
System
Fan 2
COM 6
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
5 1
5
1
CPU Fan
System Fan 2
4
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
SD331-C236/Q170
24
Standby
Power LED
LAN 2
USB 4
USB 3
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
2 10
SATA 5
System Fan 1
1
1
SMBus
21
COM 3
9
5
1
6
COM 4
2
SPI Flash
BIOS
1 9
1
9
2 10
2 10
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
33
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Digital I/O and Power Connector
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
SD330-Q170/H110
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
LAN 2
USB 4
USB 3
Line-out
Mic-in
2
11
12
1
2
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
7
8
1
2
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
Digital I/O Connector
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
1
Intel
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
1
2
1
5
PCIe x4
ITE
IT8893E
1
39
1
2
SATA 2
6
1
NXP
PTN3460
USB 3.0
(only for Q170)
Digital I/O
1
40
LVDS LCD Panel
SMBus
USB 5-6
11
10+
1
2
19
USB 2.0
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
20
1
LCD/Inverter Power
5
1
6
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
Pins
SATA 3
SATA 3.0
1 9
1
2 10
2
COM 5
1
System
Fan 2
COM 6
IC
Digital I/O
19
1
Front
Panel
Intel
WGI210AT
USB 3.0
1
The 8-bit Digital I/O connector provides monitoring and control function to the connected
devices. We have built support software called EAPI that enables the functionality of
hardware components. Please contact our technical support or sales representatives for the
support software package.
13
1
USB 3.0
1
2
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
5
CPU Fan
1
8
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
TPM
(optional)
21
Pins
Pin Assignment
1
GND
2
+12V
3
DIO7
4
+12V
5
DIO6
6
GND
7
DIO5
8
+5V
9
DIO4
10
+5V
11
DIO3
12
GND
13
DIO2
14
V_5P0_STBY
15
DIO1
16
V_5P0_STBY
17
DIO0
18
GND
19
GND
20
NC
System Fan 2
4
COM 1
VGA
1
1
Pin Assignment
LPC
ASMedia
ASM1442
12
DVI-D
DP++
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
SD331-C236/Q170
24
LAN 2
USB 4
USB 3
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
9
SATA 5
System Fan 1
1
1
SMBus
21
COM 3
2 10
5
1
6
COM 4
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
34
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
SATA (Serial ATA) Connectors
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
5
14 13
+12V
Power
Chrontel
CH7517A
7
1
8
COM 1
VGA
1
1
Socket LGA1151
TPM
(optional)
GND
TXP
TXN
GND
RXN
RXP
GND
PS/2 KB/MS
USB 6
USB 5
USB 2.0
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
SD330-Q170/H110
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
Intel
WGI210AT
USB 3.0
2
11
12
1
2
7
8
1
2
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
SD330-Q170/H110:
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
PCI 2
Q170
SATA 1
1
2
•
Support Integrated Advanced Host Controller Interface (AHCI) controller with Intel® Rapid
Storage Technology (Note that SKUs with the Intel® H110 chipset do not support RAID.)
SATA 2
6
1
5
1
PCIe x4
ITE
IT8893E
1
39
1
2
4 Serial ATA ports
-Support SATA 3.0 with data transfer rate up to 6Gb/s
SATA 0
1
S/PDIF
NXP
PTN3460
•
1
Intel
Buzzer
7
1
Front
Panel
Line-out
Mic-in
1
Features
1
LAN 2
USB 4
USB 3
1
13
1
USB 3.0
1
40
LVDS LCD Panel
USB 2.0
USB 9-10 USB 7-8
USB 5-6
1
2
19
SMBus
USB 3.0
(only for Q170)
Digital I/O
11
10+
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
5
1
6
2
1
9
10
1
6
9
2 10
COM 2
5
2
1
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
SD331-C236/Q170:
System
Fan 2
COM 6
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
5 1
5
1
CPU Fan
1
8
5
14 13
+12V
Power
Chrontel
CH7517A
•
6 Serial ATA ports
-Support SATA 3.0 with data transfer rate up to 6Gb/s
•
Support Integrated Advanced Host Controller Interface (AHCI) controller with Intel® Rapid
Storage Technology
System Fan 2
4
COM 1
VGA
1
1
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
BIOS Setting
13
1
1
1
Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
2
Front
Panel
Intel
WGI210AT
USB 3.0
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
SD331-C236/Q170
The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the
SATA cable to one of the SATA connectors and the other end to your SATA device.
24
Standby
Power LED
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
21
COM 3
9
2 10
5
1
SATA 5
System Fan 1
1
1
SMBus
6
COM 4
2
SPI Flash
BIOS
1 9
1
9
2 10
2 10
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
35
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
8
COM 1
VGA
1
1
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
TPM
(optional)
DATA+
DATAN.C.
N.C.
N.C.
COM 1
2
RXD+
RXDTXD+
TXDN.C.
PS/2 KB/MS
USB 6
USB 5
USB 2.0
DCD
(or +12V)
RXD
TXD
DTR
GND
COM (Serial) Ports
1 2345
1 2345
1 2345
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
1
2
7
8
1
2
RS232
LAN LED
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
1
Intel
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
9
1
2
6
1
5
1
NXP
PTN3460
1
2
SATA 2
PCIe x4
ITE
IT8893E
1
39
Digital I/O
COM 2:
RS232/422/485
USB 2.0
USB 9-10 USB 7-8
USB 5-6
11
10+
1
2
19
1
40
LVDS LCD Panel
SMBus
USB 3.0
(only for Q170)
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
5
1
6
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
6 2
6
1
5 1
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
1 9
1
2 10
1
2
System
Fan 2
RS232
COM 3/4/5/6: RS232
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
5
CPU Fan
14 13
Socket LGA1151
TPM
(optional)
12
DVI-D
DP++
ATX
Power
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
SD331-C236/Q170
13
1
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
Battery
Line-out
Mic-in
11
12
1
2
Connecting External Serial Ports
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket to
an available slot at the rear of the system chassis then insert the serial port cable to the COM
connector. Make sure the colored stripe on the ribbon cable aligns with pin 1 of the COM connector.
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
COM 2:
RS232/422/485
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
RS485
The pin assignments of COM port 2 will vary according to the jumper settings (JP11, JP12, and
JP13). JP14 is used to configure COM 2 to pure RS232 or RS232 with power. Refer to “Serial
Port RS232/422/485 Select” and “Serial Port Power Select“ in Chapter 4 for more information.
COM 3 to COM 6 are fixed at RS232.
The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that
can be used with modems, serial printers, remote display terminals, and other serial devices.
24
Standby
Power LED
VGA
LAN 1
USB 2
USB 1
1
2
COM 2 port
21
LPC
ASMedia
ASM1442
COM 1:
RS232/422/485
9
5
+12V
Power
Chrontel
CH7517A
RS422
Full Duplex
1
2
Please refer to the “Rear Panel I/O Ports“ section in this chapter for more information.
1
8
RS485
COM 1 port
1
1
System Fan 2
4
COM 1
VGA
9
COM 6
IC
COM 1
1
2
SATA 3
SATA 3.0
COM 5
RS422
Full Duplex
SPI
Program
8 Header
NC.
NC.
NC.
NC.
DATA+
Battery
NC.
NC.
NC.
DATA-
Line-out
Mic-in
N.C.
N.C.
N.C.
N.C.
2
12
NC.
NC.
NC.
TXD+
RXD+
USB 3.0
1
1
11
Front
Panel
Intel
WGI210AT
6789
N.C.
N.C.
N.C.
N.C.
1
NC.
NC.
TXDRXD-
USB 3.0
LAN 2
USB 4
USB 3
6789
6789
13
1
CTS
DSR
DTR
RXD
SD330-Q170/H110
Intel
WGI219LM
LAN 1
USB 2
USB 1
DSR
RTS
CTS
RI
(or +5V)
COM 1:
RS232/422/485
Standby
Power LED
RI
(or +5V)
RTS
GND
TXD
DCD
(or +12V)
VGA
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
21
COM 3
9
2 10
5
1
SATA 5
1
SMBus
6
COM 4
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
COM 5
BIOS Setting
System Fan 1
1
2
19
Configure the serial ports with more advanced options such as the RS485 auto flow mechanism in the Advanced menu (“SIO NUVOTON6106D” submenu) of the BIOS. Refer to Chapter
7 for more information.
Buzzer
1
2
DIO
COM 6
COM 3/4/5/6: RS232
36
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
6
5 1
6 2
5
6
1
5 1
4
5
USB 6
USB 5
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
TPM
(optional)
20
21
LPC
ASMedia
ASM1442
USB 2.0
12
Over Current Protection
D+
DGND
TX+
TXGND
RX+
RXPWR
DVI-D
DP++
LAN 1
USB 2
USB 1
USB 4
Standby
Power LED
Intel
WGI219LM
USB 3
1
Line-out
Mic-in
DDR4_1
SPI
Program
8 Header
PCI 2
6
1
5
SATA 1
1
NXP
PTN3460
ITE
IT8893E
1
39
1
2
USB 5-6
1
2
19
1
40
LVDS LCD Panel
SMBus
USB 3.0
(only for Q170)
Digital I/O
11
10+
USB 2.0
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
20
1
LCD/Inverter Power
5
1
6
2
1
9
10
6 2
6
1
2
5 1
6 2
5
6
5 1
5
1
2
9
2 10
COM 2
5
1
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
Chrontel
CH7517A
14 13
Socket LGA1151
TPM
(optional)
ASMedia
ASM1442
12
DVI-D
DP++
USB 4
USB 3
Intel
WGI219LM
1
2
Front
Panel
Intel
WGI210AT
Battery
Line-out
Mic-in
USB 3.0
The system board is also equipped with internal USB 2.0 and USB 3.0 ports via pin headers.
The 10-pin connector (USB 2.0) allows you to connect 2 additional ports. And the 20-pin connector (USB 3.0) allows you to connect 2 additional ports. These additional USB ports may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear
of the system chassis and then insert the USB port cables to a connector.
13
1
1
USB 3.0
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
USB 5-6 , 7-8
Realtek
ALC888
1
1
1
2 USB 9-10
USB 7-8
USB 2.0
1
PCIe 2 (PCIe x4)
S/PDIF
SATA 1
1
PCIe 3 (PCIe x8)
SATA 2
Q170
SATA 3
SATA 4
65
PCIe 4 (PCIe x4)
21
USB 5-6
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
21
COM 3
9
2 10
5
1
SATA 5
System Fan 1
1
1
SMBus
6
COM 4
1
2 10
2 10
9
1 9
1
2 10
COM 5
2
Driver Installation
2
SPI Flash
BIOS
1 9
Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)
of the BIOS. Refer to Chapter 7 for more information.
1
1
11
10
BIOS Setting
1
SATA 0
Intel
Nuvoton
1
NCT6106D
Chassis
Intrusion
Q170: 8 USB 3.0 (4 external ports and 4 via internal pin headers) and 5 USB 2.0 (2
external ports and 3 via internal pin headers and a vertical port)
The USB device allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
ATX
Power
LAN 2
USB 4
USB 3
•
24
Standby
Power LED
USB 3.0
C236: 8 USB 3.0 (4 external ports and 4 via internal pin headers) and 6 USB 2.0 (2 external ports and 4 via internal pin headers)
5
LPC
LAN 1
USB 2
USB 1
•
1
+12V
Power
21
USB 5
USB 2.0
Q170: 6 USB 3.0 (4 external ports and 2 via internal pin headers) and 6 USB 2.0 (2
external ports and 4 via internal pin headers)
1
1
System Fan 2
8
USB 6
•
System
Fan 2
COM 6
SD331-C236/Q170:
CPU Fan
4
COM 1
VGA
H110: 4 USB 3.0 (all external ports) and 5 USB 2.0 (2 external ports and 3 via internal pin
headers and a vertical port)
1
6
IC
2
1
2
9
10
•
SATA 2
PCIe x4
4
SATA 0
Q170
1
2
USB 2.0
SD330-Q170/H110:
1
1
S/PDIF
PS/2 KB/MS
USB 6
USB 5
USB 2.0
9
10
2
1
SD331-C236/Q170
USB 3.0
8
1
Mini PCIe
(only for Q170)
Intel
Buzzer
USB 2
USB 1
7
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
1
USB 3.0 USB 5-6
2
SPI Flash
BIOS
DDR4_3
PCI 1
1
12
1
LAN LED
1
Realtek
ALC888
1
2
11
Battery
PCIe x16
1
9
10
2
USB 2.0 USB 9-10, 7-8
1
Front
Panel
Intel
WGI210AT
USB 3.0
USB 3.0
13
1
USB 3.0
LAN 2
USB 4
USB 3
1
24
ATX
Power
USB 2
USB 1
USB 2.0 vertical port
(for SD330-H110/SD331-Q170)
1
1
1
8
COM 1
VGA
USB 3.0
CPU Fan
System Fan 1
Key
GND
+Data
-Data
VCC
6 2
1
2
N. C.
GND
+Data
-Data
VCC
2
D+
DGND
TX+
TXGND
RX+
RXPWR
PS/2 KB/MS
USB 6
USB 5
USB 2.0
VCC
DataData+
GND
USB Ports
SD330-Q170/H110
19
Buzzer
1
2
DIO
You may need to install proper drivers in your OS to use USB devices. Refer to Chapter 8 and
your operating system’s documentation for more information.
COM 6
37
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Cooling Fan Connectors
SD330-Q170/H110
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
1
1
System Fan 1
1
5
14 13
+12V
Power
Chrontel
CH7517A
4
1
CPU Fan
8
COM 1
VGA
CPU fan
Socket LGA1151
TPM
(optional)
System Fan 1
21
LPC
ASMedia
ASM1442
12
CPU fan
24
System fan 1, 2
DVI-D
DP++
ATX
Power
LAN 1
USB 2
USB 1
3
1
13
1
USB 3.0
1
2
11
12
1
2
7
8
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
Power
SPI
Program
Mini PCIe
(only for Q170)
1
1
PCI 1
1
1
Intel
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
3
SATA 1
1
2
6
1
5
1
NXP
PTN3460
Ground Sense
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
Realtek
ALC888
4
Ground Speed
Power Control
Sense
1
LAN 2
USB 4
USB 3
1
1
Standby
Power LED
Intel
WGI219LM
SATA 2
PCIe x4
1
1
39
2
40
LVDS LCD Panel
ITE
IT8893E
USB 2.0
USB 9-10 USB 7-8
USB 5-6
1
2
11
10+
5
1
6
USB 3.0
(only for Q170)
Digital I/O
19
1
SMBus
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
9
COM 4
SD331-C236/Q170
SATA 3
SATA 3.0
1 9
1
2 10
2
COM 5
1
System Fan 2
System
Fan 2
COM 6
CPU fan
PS/2 KB/MS
USB 6
USB 5
USB 2.0
6 2
6
1
2
5 1
6 2
5
6
5 1
5
1
CPU Fan
4
System Fan 2
The fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
14 13
BIOS Setting
5
+12V
Power
Chrontel
CH7517A
1
1
1
8
COM 1
VGA
4
1
IC
2
Socket LGA1151
TPM
(optional)
The Advanced menu (“PC Health Status” submenu) of the BIOS will display the current speed
of the cooling fans. Refer to Chapter 7 for more information.
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
24
System Fan 2
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
1
3
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
2 10
SATA 5
System Fan 1
1
1
SMBus
21
COM 3
9
5
1
6
COM 4
SPI Flash
BIOS
1 9
1
9
2 10
2 10
1 9
1
2 10
COM 5
2
System fan 1
1
2
19
Buzzer
1
2
DIO
3
COM 6
38
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Chassis Intrusion Connector
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
1
8
COM 1
VGA
SD330-Q170/H110
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
1
LAN 2
USB 4
USB 3
1
2
11
12
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
Ground
Chassis
signal
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
7
8
1
2
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
1
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
1
1
Intel
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
2
SATA 1
1
2
1
1
NXP
PTN3460
1
2
2
13
1
USB 3.0
SATA 2
6
5
PCIe x4
ITE
IT8893E
1
39
1
40
LVDS LCD Panel
USB 3.0
(only for Q170)
Digital I/O
19
SMBus
USB 5-6
1
2
11
10+
1
6
2
USB 2.0
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
20
1
LCD/Inverter Power
5
1
9
10
1
6
2
9
2 10
COM 2
5
1
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
9
COM 4
SD331-C236/Q170
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
System
Fan 2
COM 6
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
5 1
5
1
COM 1
VGA
CPU Fan
System Fan 2
4
1
8
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
Socket LGA1151
The board supports the chassis intrusion detection function. Connect the chassis intrusion
sensor cable from the chassis to this connector. When the system’s power is on and a chassis
intrusion occurred, an alarm will sound. When the system’s power is off and a chassis intrusion
occurred, the alarm will sound only when the system restarts.
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
24
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
SATA 2
Q170
1
1
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
USB 5-6
11
10
2
21
Chassis
Intrusion
2
6
PCIe 4 (PCIe x4)
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
5
1
65
65
21
21
COM 3
9
2 10
5
1
SATA 5
System Fan 1
1
1
SMBus
6
COM 4
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
39
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
LPC Connector
SD330-Q170/H110
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
14 13
24
DVI-D
DP++
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
1
2
11
12
1
2
7
8
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
2 1
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
14 13
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
1
13
1
USB 3.0
LAN 2
USB 4
USB 3
1
Intel
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
The Low Pin Count Interface was defined by Intel® Corporation to facilitate the industry’s transition towards legacy free systems. It allows the integration of low-bandwidth legacy I/O components within the system, which are typically provided by a Super I/O controller. Furthermore, it
can be used to interface firmware hubs, Trusted Platform Module (TPM) devices and embedded
controllers. Data transfer on the LPC bus is implemented over a 4 bit serialized data interface,
which uses a 24MHz LPC bus clock. For more information about LPC bus, please refer to the
Intel® Low Pin Count Interface Specification Revision 1.1’. The table below indicates the pin assignments of the LPC connector.
1
2
6
1
5
SATA 2
PCIe x4
1
NXP
PTN3460
1
1
39
2
40
LVDS LCD Panel
ITE
IT8893E
SMBus
USB 2.0
USB 9-10 USB 7-8
USB 5-6
1
2
19
6
USB 3.0
(only for Q170)
Digital I/O
1
11
10+
5
9
1
9
1
10
2
10
2
CPU Fan
1
20
1
LCD/Inverter Power
1
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
2
1
System
Fan 2
2 1
COM 6
SD331-C236/Q170
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
5
4
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
System Fan 2
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
24
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
1
1
Pin
1
3
5
7
9
11
13
2
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
9
SATA 5
6
COM 4
1
2 10
2 10
9
1 9
1
2 10
COM 5
2
Pin Assignment
L_AD1
L_AD0
3V3
GND
Kev
GND
5V
1
2
SPI Flash
BIOS
1 9
Pin
2
4
6
8
10
12
14
System Fan 1
1
SMBus
21
COM 3
2 10
5
1
Pin Assignment
L_CLK
L_RST#
L_FRAME#
L_AD3
L_AD2
INT_SERIRQ
5VSB
19
Buzzer
1
2
DIO
COM 6
40
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Power Connectors
SD330-Q170/H110
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
8
COM 1
VGA
1
1
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
12 24
TPM
(optional)
12 24
+3.3VDC
+12VDC
+12VDC
+5VSB
PWR_OK
COM
+5VDC
COM
+5VDC
COM
+3.3VDC
+3.3VDC
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
1
1
2
11
12
1
2
7
8
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
Mini PCIe
(only for Q170)
1
1 13
ATX power
1
PCI 1
Realtek
ALC888
1
13
1
USB 3.0
LAN 2
USB 4
USB 3
1
Intel
SATA 0
S/PDIF
PCI 2
Q170
12V power
Ground
12V
1 13
ATX power
1
Buzzer
COM
+5VDC
+5VDC
+5VDC
NC
COM
COM
COM
PS_ON#
COM
-12VDC
+3.3VDC
1
6
5 1
6 2
5
6 2
1
2
4
2
8
PS/2 KB/MS
USB 6
USB 5
USB 2.0
SATA 1
1
1
5
1
NXP
PTN3460
ITE
IT8893E
1
39
1
2
SATA 2
PCIe x4
Digital I/O
1
40
LVDS LCD Panel
USB 2.0
USB 9-10 USB 7-8
USB 5-6
11
10+
1
2
19
20
1
LCD/Inverter Power
SD331-C236/Q170
PS/2 KB/MS
USB 6
USB 5
USB 2.0
6 2
6
1
2
5 1
6 2
5
6
1
9
1
2
10
2
5 1
5
CPU Fan
6
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
System
Fan 2
1
2
COM 6
1
1
System Fan 2
4
1
8
5
14 13
+12V
Power
Chrontel
CH7517A
9
10
1
IC
2
1
COM 1
VGA
SMBus
USB 3.0
(only for Q170)
5
Socket LGA1151
Ground
1
6
4
2
TPM
(optional)
Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1.
An ATX12V power supply unit has a standard 24-pin ATX main power connector that must be
inserted into the 24-pin connector. The 8-pin +12V power connector enables the delivery of
more +12VDC current to the processor’s Voltage Regulator Module (VRM).
21
LPC
DVI-D
DP++
24
8
12
Standby
Power LED
12V
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
1
The power connectors from the power supply unit are designed to fit the 24-pin and 8-pin
connectors in only one orientation. Make sure to find the proper orientation before plugging
the connectors.
13
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
5
ASMedia
ASM1442
Battery
Line-out
Mic-in
11
12
1
2
Please use the recommended power supply unit with the correct wattage. Insufficient power
supplied to the system may result in system instability or the add-in boards and peripherals
not functioning properly. Calculating the system’s approximate power usage is important to
ensure that the power supply meets the system’s consumption requirements.
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
2 10
SATA 5
System Fan 1
1
1
SMBus
21
COM 3
9
5
1
6
COM 4
2
SPI Flash
BIOS
1 9
1
9
2 10
2 10
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
41
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
SMBus Connector
SD330-Q170/H110
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1
8
COM 1
VGA
1
1
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
Standby
Power LED
LAN 1
USB 2
USB 1
1
2
11
12
1
2
7
8
1
2
SMBUS_Alert
SMBUS_CLK
3V3SB
1
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
6 5
Mini PCIe
(only for Q170)
1
1
PCI 1
1
Intel
SMBUS_Data
GND
Realtek
ALC888
1
13
1
USB 3.0
LAN 2
USB 4
USB 3
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
1
2
6
1
5
1
NXP
PTN3460
ITE
IT8893E
1
39
1
2
SATA 2
PCIe x4
Digital I/O
1
40
LVDS LCD Panel
SMBus
USB 3.0
(only for Q170)
USB 2.0
USB 9-10 USB 7-8
USB 5-6
11
10+
1
2
19
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
SD331-C236/Q170
5
1
6
2
1
9
10
9
2 10
COM 2
1
6
5
2
1
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
9
COM 4
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
2 1
Intel
WGI219LM
System
Fan 2
COM 6
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
5
CPU Fan
System Fan 2
4
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
Socket LGA1151
TPM
(optional)
The SMBus (System Management Bus) connector is used to connect SMBus devices. It is a
multiple device bus that allows multiple chips to connect to the same bus and enable each one
to act as a master by initiating data transfer.
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
24
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
1
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
1
SATA 0
SATA 1
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
9
SATA 5
System Fan 1
1
1
SMBus
21
COM 3
2 10
5
1
6
COM 4
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
42
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Standby Power LED
Battery
SD330-Q170/H110, SD331-C236/Q170
SD330-Q170/H110, SD331-C236/Q170
IC
2
PS/2 KB/MS
USB 6
USB 5
USB 2.0
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
System Fan 1
2
6 2
6
1
2
5 1
6 2
5
6
5 1
5
1
CPU Fan
1
8
COM 1
VGA
5
TPM
14 13
(optional)
Socket LGA1151
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
System Fan 2
4
+12V
Power
Chrontel
CH7517A
1
1
1
8
COM 1
VGA
PS/2 KB/MS
USB 6
USB 5
USB 2.0
CPU Fan
Socket LGA1151
21
LPC
ASMedia
ASM1442
21
LPC
ASMedia
ASM1442
12
12
DVI-D
DP++
24
ATX
Power
Standby
Power LED
Intel
WGI219LM
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
11
12
1
2
7
8
1
DDR4_1
1
2
SPI Flash
BIOS
DDR4_3
1
PCIe 2 (PCIe x4)
1
Intel
PCI 2
1
S/PDIF
1
NXP
PTN3460
1
2
6
1
5
Q170
ITE
IT8893E
1
39
40
LVDS LCD Panel
USB 3.0
(only for Q170)
Digital I/O
1
19
SMBus
USB 5-6
1
2
11
10+
LCD/Inverter Power
20
1
USB 2.0
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
5
1
6
2
65
1
9
10
9
2 10
COM 2
1
1
6
5
2
1
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
1
2 10
2
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
SATA 3
SATA 3.0
1 9
COM 5
SATA 3
SATA 4
1
SATA 2
PCIe x4
1
SATA 2
SATA 1
1
2
Battery
8
SATA 1
1
PCIe 3 (PCIe x8)
SATA 0
Q170
2
Intel
1
S/PDIF
Buzzer
12
1
1
SATA 0
1
Realtek
ALC888
11
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
SATA 3.0
Realtek
ALC888
PCI 1
2
LAN LED
1
PCIe 1 (PCIe x16 or PCIe x8)
Mini PCIe
(only for Q170)
1
Battery
Line-out
Mic-in
SPI
Program
1
Front
Panel
Intel
WGI210AT
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
13
1
1
USB 3.0
LAN LED
Battery
PCIe x16
1
LAN 2
USB 4
USB 3
1
LAN 2
USB 4
USB 3
Intel
WGI219LM
USB 3.0
13
1
USB 3.0
ATX
Power
LAN 1
USB 2
USB 1
Standby Power LED
24
Standby
Power LED
DVI-D
DP++
LAN 1
USB 2
USB 1
TPM
(optional)
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
2 10
SATA 5
System Fan 1
1
1
SMBus
21
COM 3
9
5
1
6
COM 4
1
2 10
2 10
System
Fan 2
2
SPI Flash
BIOS
1 9
9
1 9
1
2 10
COM 5
2
19
Buzzer
1
2
DIO
COM 6
COM 6
The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source
of power when the main power is shut off.
This LED will be red when the system is in the standby mode. It indicates that there is power
on the system board. Power off the PC and then unplug the power cord prior to installing any
devices. Failure to do so will cause severe damage to the motherboard and components.
Safety Measures
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
43
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Front Panel Connector
SD330-Q170/H110
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
1 2
1
8
COM 1
VGA
1
1
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
TPM
(optional)
12
24
DVI-D
DP++
Standby
Power LED
Intel
WGI219LM
11 12
13
1
USB 3.0
1
1
LAN 2
USB 4
USB 3
2
Front
Panel
Intel
WGI210AT
USB 3.0
Line-out
Mic-in
11
12
1
2
7
8
1
2
LAN LED
Battery
1
DDR4_1
PCIe x16
SPI Flash
BIOS
DDR4_3
1 2
SPI
Program
This connector provides several control and LED indicator functions.
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
Mini PCIe
(only for Q170)
1
1
PCI 1
Realtek
ALC888
1
PWR-BTN
RESET-SW
ATX
Power
LAN 1
USB 2
USB 1
PWR-LED
HDD-LED
21
LPC
ASMedia
ASM1442
HDD-LED - HDD LED
1
Intel
SATA 0
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
This LED will be lit when the hard drive is being accessed.
1
2
6
1
5
SATA 2
PCIe x4
1
NXP
PTN3460
1
39
1
2
ITE
IT8893E
USB 3.0
(only for Q170)
Digital I/O
USB 2.0
USB 9-10 USB 7-8
USB 5-6
11
10+
1
2
19
1
40
LVDS LCD Panel
SMBus
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
5
1
6
2
1
9
10
5
2
1
9
2 10
COM 2
SD331-C236/Q170
1
6
2
6 2
1
5 1
6 2
6
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
11 12
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
RESET SW - Reset Switch
System
Fan 2
COM 6
This switch allows you to reboot the system without having to power off the system.
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
5
CPU Fan
System Fan 2
4
This switch is used to power on or off the system.
1
8
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
PWR-BTN - Power Switch
1
1
Socket LGA1151
TPM
(optional)
PWR-LED - Power/Standby LED
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
24
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Power On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
LAN 2
USB 4
USB 3
1
1
2
Pin Pin Assignment
Front
Panel
Intel
WGI210AT
USB 3.0
13
1
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
8
HDD-LED
SATA 3.0
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
SATA 1
Intel
1
PCIe 3 (PCIe x8)
SATA 3
SATA 4
1
65
1
Nuvoton
NCT6106D
2
21
Chassis
Intrusion
USB 5-6
11
10
6
PCIe 4 (PCIe x4)
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
5
1
65
65
21
2 10
1
6
COM 4
1
2
SPI Flash
BIOS
1 9
1
9
2 10
2 10
1 9
1
2 10
COM 5
2
RESET SW
SATA 5
System Fan 1
1
SMBus
21
COM 3
9
5
19
5
Signal
7
Ground
9
RST Signal
11
N.C.
2
LED Power
PWR-LED 4
LED Power
6
Signal
8
Ground
10
Signal
1
SATA 2
Q170
HDD Power
1
SATA 0
S/PDIF
3
Pin Pin Assignment
PWR-BTN
Buzzer
1
2
DIO
COM 6
44
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
Expansion Slots
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
SD330-Q170/H110:
1
8
COM 1
VGA
1
1
5
14 13
+12V
Power
Chrontel
CH7517A
Socket LGA1151
Mini PCIe Slot (only for SD330-Q170)
TPM
(optional)
The SD330-Q170 board is equipped with a full-size Mini PCIe slot (PCIe/USB/SATA signals).
This slot supports the installation of a Mini PCIe or an mSATA card. To switch the interface
between Mini PCIe and mSATA, please refer to Jumper Settings in Chapter 4.
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
LAN 1
USB 2
USB 1
Q170
PCIe x16 (Gen 3)
H110
PCIe x16 (Gen 3)
1
LAN 2
USB 4
USB 3
PCI
PCI
PCI
Line-out
Mic-in
PCIe x4 (Gen2)
11
12
1
2
7
8
1
2
LAN LED
1
DDR4_1
SPI Flash
BIOS
DDR4_3
PCI Slots
SPI
Program
8 Header
DDR4_2
7
Chassis
DDR4_2
(only for Q170)
Intrusion
(only for Q170)
These PCI slots support PCI expansion cards.
Mini PCIe
(only for Q170)
1
PCI 1
Realtek
ALC888
1
Intel
SATA 0
PCI Express x4 Slot
1
S/PDIF
PCI 2
Q170
Buzzer
SATA 1
1
2
PCIe x4 (Gen3)
2
Battery
PCIe x16
1
1
Front
Panel
Intel
WGI210AT
USB 3.0
1
PCI
Install a PCI Express x16 (lanes) expansion card such as a graphics card into the PCIe x16
(lanes) slot. To install a graphics card into this slot, align the graphics card above the slot then
press it down firmly until it is completely seated in the slot. The retaining lever on the end of
the slot will automatically hold the graphics card in place.
13
1
USB 3.0
SD330-Q170/H110
PCI Express x16 Slot
Standby
Power LED
Intel
WGI219LM
1
5
1
NXP
PTN3460
2
PCIe x4
ITE
IT8893E
1
39
1
Install PCI Express cards such as network cards or other expansion cards. Note that the
SD330-Q170 board supports PCIe Gen3 x4 (lanes) and the SD330-H110 board supports PCIe
Gen2 x4 (lanes).
SATA 2
6
1
40
LVDS LCD Panel
SMBus
USB 3.0
(only for Q170)
Digital I/O
USB 5-6
11
10+
1
2
19
USB 2.0
USB 9-10 USB 7-8
20
1
LCD/Inverter Power
9
1
9
1
10
2
10
2
5
1
6
2
1
9
10
1
6
5
2
1
9
2 10
COM 2
2
6 2
6 2
6
1
5 1
5 1
5
1 9
1
2 10
2 10
COM 3
COM 4
9
SATA 3
SATA 3.0
1 9
1
2 10
COM 5
1
2
System
Fan 2
COM 6
IC
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
5
CPU Fan
System Fan 2
4
5
14 13
+12V
Power
Chrontel
CH7517A
PCI Express x16 (x16 or x8 Gen3 signal) Slot
1
8
COM 1
VGA
SD331-C236/Q170:
1
1
Socket LGA1151
TPM
(optional)
Install a PCI Express x16 (lanes) expansion card such as a graphics card into this slot. It
shares the signal with the below PCIe x8 slot. To install a graphics card into this slot, align the
graphics card above the slot then press it down firmly until it is completely seated in the slot.
The retaining lever on the end of the slot will automatically hold the graphics card in place.
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
SD331-C236/Q170
LAN 2
USB 4
USB 3
Q170
PCI Express x 8 (Gen3 signal) Slot
1
The second PCIe x8 slot shares the signal with the above PCIe x16 slot. The PCIe x16 automatically switches to x8 signal when this slot is occupied.
2
Front
Panel
Intel
WGI210AT
Battery
Line-out
Mic-in
11
12
1
2
LAN LED
1
PCIe x16 (x16 or x8 Gen3)
13
1
1
USB 3.0
C236
24
7
DDR4_1
DDR4_3
DDR4_2
DDR4_4
PCIe 1 (PCIe x16 or PCIe x8)
PCI Express x4 (Gen3 signal) Slots
8
Install PCI Express expansion cards to expand the I/O capability of the system.
SATA 3.0
PCIe x4 (Gen3)
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
S/PDIF
SATA 1
1
PCIe x8 (Gen3)
PCIe 3 (PCIe x8)
1
SATA 2
Q170
SATA 3
SATA 4
1
65
PCIe x4 (Gen3)
1
SATA 0
Intel
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
11
10
USB 2.0
USB 9-10 USB 7-8
USB 7-8
11
1 10
1
6
5
2
1
COM 2
9
1
9
1
10
2
10
2 10
9
1
65
65
21
6
COM 4
1
2
SPI Flash
BIOS
1 9
1
2 10
2 10
9
1 9
1
2 10
2
COM 5
BIOS Setting
SATA 5
System Fan 1
1
SMBus
21
COM 3
9
2 10
5
1
19
Configure these PCIe slots including their speed in the Advanced menu (“PCI Express Configuration” submenu) of the BIOS. Refer to Chapter 7 for more information.
Buzzer
1
2
DIO
COM 6
45
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 5
LVDS LCD Panel Connector
LVDS LCD Panel Connector (for SD330-Q170/H110 only)
LCD/Inverter Power Connector
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
CPU Fan
System Fan 1
COM 1 RS232/Power
Select (JP9)
1
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
COM 1 RS232/485
Select (JP8)
8
COM 1
VGA
Pins
Socket LGA1151
TPM
(optional)
Function
Pins
LCD/Inverter Power Connector
Function
Pins
Function
1
GND
2
GND
1
GND
3
LVDS_Out3+ (Odd_3+)
4
LVDS_Out7+ (Even_3+)
2
GND
5
LVDS_Out3- (Odd_3-)
6
LVDS_Out7- (Even_3-)
3
Panel Inverter Brightness Voltage Control
7
GND
8
GND
4
Panel Power
9
LVDS_Out2+ (Odd_2+)
10
LVDS_Out6+ (Even_2+)
5
+3.3V
11
LVDS_Out2- (Odd_2-)
12
LVDS_Out6- (Even_2-)
6
Panel Backlight On/Off Control
13
GND
14
GND
7
+12V
15
LVDS_Out1+ (Odd_1+)
16
LVDS_Out5+ (Even_1+)
8
+12V
17
LVDS_Out1- (Odd_1-)
18
LVDS_Out5- (Even_1-)
19
GND
20
GND
21
LVDS_Out0+ (Odd_0+)
22
LVDS_Out4+ (Even_0+)
23
LVDS_Out0- (Odd_0-)
24
LVDS_Out4- (Even_0-)
25
GND
26
GND
27
LVDS_CLK1+ (Odd_CLK+)
28
LVDS_CLK2+ (Even_CLK+)
29
LVDS_CLK1- (Odd_CLK-)
30
LVDS_CLK2- (Even_CLK-)
31
GND
32
GND
33
DDC_CLK
34
NC
35
DDC_DATA
36
+3.3V
37
Panel Power
38
Panel Power
39
Panel Power
40
Panel Power
21
LPC
ASMedia
ASM1442
12
24
DVI-D
DP++
ATX
Power
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
Auto Power-on 1
Select (JP5) 1
Intel
WGI210AT
USB 3.0
11
12
1
2
7
8
1
2
LAN LED
Battery
1
Clear CMOS
Data (JP1)
PCIe x16
Realtek
ALC888
7
Chassis
Intrusion
1
Nuvoton
NCT6106D
1
SATA 0
Q170
1
2
6
1
5
SATA 1
1
COM 2 RS232/Power
Select (JP14)
Panel Power Select (JP2)
PCIe x4
ITE
IT8893E
LCD/Inverter
Power Select (JP4) 1
2
DDR4_4
SPI
Program
8 Header
1
PCI 2
Buzzer
1
DDR4_3
DDR4_2
Intel
S/PDIF
Backlight Power
Select (JP3)
DDR4_1
SPI Flash
BIOS
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
NXP
PTN3460
2
Front
Panel
Line-out
Mic-in
1
13
1
USB 3.0
LAN 2
USB 4
USB 3
Digital I/O
39
1
40
LVDS LCD Panel
1
2
19
SMBus
USB 2.0
USB 9-10 USB 7-8
8
1
39
2
40
LVDS Panel
9
1
9
1
10
2
10
2
1
LCD/Inverter Power
1
6
2
SATA 2
1
6
5
2
1
(JP13)
USB 3.0
USB 5-6
11
10
5
1
9
10
9
2 10
COM 2
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
1 9
2 10
COM 3
2 10
COM 4
1
SATA 3
SATA 3.0
(JP11)
1 9
1
2 10
COM 5
2
COM 6
1
System
Fan 2
The system board allows you to connect a LCD panel with the LVDS LCD panel connector and
the LCD/Inverter power connector. These connectors transmit video signals and power from
the system board to the LCD display panel.
Refer to the right side for the pin assignments of these connectors.
BIOS Setting
Note:
DFI board's LVDS connector: Hirose DF13-40DP-1.25V(91)/40P/1.25mm; cable side
connector: Hirose DF13-40DS-1.25C.
Configure the LCD panel in the Advanced menu (“Video Configuration” submenu) of the BIOS.
Refer to Chapter 7 for more information.
46
Chapter 5 Ports and Connectors
www.dfi.com
Chapter 6
Chapter 6 - Mounting Options
The mechanical drawing of the wall mount illustration with dimentions.
Note:
The system unit used in the following illustrations may not resemble the actual one.
These illustrations are for reference only.
25.50
There are 2 mount brackets available:
•
Wall mount
Ø4.60
•
230
160
80
40
Ø3.60
Rack-mount tray bracket
Wall Mount
25.50
Wall mount kit include:
•
2 wall mount brackets
1. On the bottom of the system, use 4 mounting screws to secure the wall mount brackets on
each side of the system.
Ø3.60
Mounting screw
230
160
80
40
Mounting screw
Ø4.60
385
Mounting screw
Mounting screw
47
Chapter 6 Mounting Options
www.dfi.com
Chapter 6
Rack Tray Mount
Rack-mount tray kit include:
•
2 Rack-mount tray brackets
1. Place the system on the rack-mount tray and align the mounting holes of the tray with the
mount bracket.
2. Follow the rack manufacture's instruction to properly secure the system to the rack.
48
Chapter 6 Mounting Options
www.dfi.com
Chapter 7
Chapter 7 - BIOS Setup
Legends
Overview
The BIOS is a program that takes care of the basic level of communication between the CPU
and peripherals. It contains codes for various advanced features found in this system board.
The BIOS allows you to configure the system and save the configuration in a battery-backed
CMOS so that the data retains even when the power is off. In general, the information stored
in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been
made such as a hard drive replaced or a device added.
It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need
to install a new CMOS battery and reconfigure the BIOS settings.
Note:
The BIOS is constantly updated to improve the performance of the system board;
therefore the BIOS screens in this chapter may not appear the same as the actual
one. These screens are for reference purpose only.
Default Configuration
Most of the configuration settings are either predefined according to the Load Optimal Defaults
settings which are stored in the BIOS or are automatically detected and configured without
requiring any actions. There are a few settings that you may need to change depending on
your system configuration.
Keys
Function
Right and Left arrows
Move the highlight left or right to select a menu
Up and Down arrows
Move the highlight up or down between submenu or fields
<Esc>
Exit the BIOS Setup Utility
<F1>
Help
<F5>
Change values
<F6>
Change values
<F9>
Setup Defaults
<F10>
Save and Exit
<Enter>
Press <Enter> to enter the highlighted submenu.
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that there are more
available fields not shown on the screen. Use the up and down arrow keys to scroll through all
the available fields.
Entering the BIOS Setup Utility
The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.
Submenu
The BIOS Setup Utility does not require an operating system to run. After you power up the
system, the BIOS message appears on the screen and the memory count begins. After the
memory test, the message “Press DEL to run setup” will appear on the screen. If the message
disappears before you respond, restart the system or press the “Reset” button. You may also
restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.
When ““ appears on the left of a particular field, it indicates that a submenu which contains
additional options are available for that field. To display the submenu, move the highlight to
that field and press <Enter>.
49
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Insyde BIOS Setup Utility
Advanced
Main
The Advanced menu allows you to configure your system for basic operation. Some entries are
defaults required by the system board, while others, if enabled, will improve the performance
of your system or let you set some features according to your preference.
The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Important:
Setting incorrect field values may cause the system to malfunction.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23.
Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.
System Date
The date format is <month>, <date>, <year>. Month displays the month, from January
to December. Date displays the date, from 1 to 31. Year displays the year, from 1980 to
2099.
50
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ACPI Settings
CPU Configuration
This section configures system’s ACPI parameters.
This section configures the CPU.
Wake on LAN
Intel® SpeedStep™
Enable or disable WOL (wake-on-LAN) to wake the system through an Ethernet adapter.
Enable or disable the Enhanced Intel SpeedStep® Technology, which helps optimize the
balance between system’s power consumption and performance. After it is enabled in the
BIOS, you can take advantage of its offering by setting power schemes from the operating
system’s power options.
Wake on PS/2
Enable or disable the use of a PS/2 device to wake the system.
Turbo Mode
After G3
Enable or disable processor turbo mode, which allows the processor core to automatically
run faster than the base frequency by taking advantage of thermal and power headroom.
Note this option is not available on the Core™ i3 processor.
This field is to specify which state the system should be in when power is re-applied after
a power failure (G3, the mechanical-off, state).
Always On The system is powered on.
Always Off The system is powered off.
CPU C States
Enable or disable CPU Power Management. It allows the CPU to go to C states when it’s
not 100% utilized.
BGRT Logo
Enable or disable the display of an operating system logo or image during boot using the
BGRT (Boot Graphics Resource Table) mechanism.
Hyper-Threading
Wake on RTC
Enable Intel® Hyper-Threading Technology (HT) on the processor to improve performance
of operating systems and software that are optimized for hyper-threading technology.
Please check the software specifications to determine if enabling HT can be advantageous
to the overall system performance.
please contact technical support. Note this option is only available for the Xeon® processor.
Automatically power the system on at a particular time every day from the real-time clock
battery. Specify the wake up time of the day below: <hour>, <minute>, <second>.
51
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Video Configuration
Internal Graphics Device
This section configures the video settings. Note that the configuration options vary depending
on the “Boot type” selected in the “Boot” menu.
Enable, disable or automatically detect the internal graphics.
Boot display
Prioritize device combination for display during system boot. Note that this option will
be shown only if the “Boot type” is set to “Dual” or “Legacy”.
The options for SD331-C236/Q170 are as follows:
DVI+DP1
DVI+VGA
DP1+DVI
DP1+VGA
VGA+DVI
VGA+DP1
The options for SD330-Q170/H110 are as follows:
LCD+DVI
LCD+DP1
LCD+VGA
DVI+DP1
DVI+VGA
DP1+DVI
DP1+VGA
VGA+DVI
Primary Display
VGA+DP1
Select the primary display for the system. Note that this option will be shown only if the
“Boot type” is set to “Dual” or “UEFI”. The options are Auto or IGFX (internal graphics).
The order of video device initialization will be as follows:
Auto mode: PEG (PCIe Graphics devices connected to PEG lanes directly routed from
the CPU )->PCIe graphics devices->PCI graphics devices->IGFX (internal graphics)
LVDS Panel Supported (Only available for SD330-Q170/H110)
Enable this option to configure your LCD panel with the following configurations:
PTN3460 Configuration Select the color depth from the following options: 18bit,
24bit, 36bit, and 8bit.
IGFX: IGFX (internal graphics)->PEG (PCIe Graphics devices connected to PEG lanes directly routed from the CPU)->PCIe graphics devices->PCI graphics devices
PEG: PEG (PCIe Graphics devices connected to PEG lanes directly routed from the CPU)
->PCIe graphics devices->IGFX (internal graphics)
PCIe: PCIe graphics devices->PEG (PCIe Graphics devices connected to PEG lanes directly
routed from the CPU )->IGFX (internal graphics)
LCD Panel Type Select the resolution for the LCD panel from the following options:
800x480, 800x600, 1024x768, 1366x768, 1280x1024, and 1920x1080.
Backlight Type
Select the backlight type from the following options: Normal+PWM, Normal+DC,
Invert+PWM, and Invert+DC.
52
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Audio Configuration
SATA Configuration
This section configures the audio settings.
This section configures SATA controllers.
HD Audio
Control the detection of the high-definition audio devices.
Disabled
High-definition audio devices will be unconditionally disabled.
Enabled
High-definition audio devices will be unconditionally enabled.
Auto
High-definition audio devices will be enabled if present and disabled otherwise.
53
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
SATA Controller(s)
USB Configuration
Enable or disable Serial ATA controllers.
This section configures the parameters of the USB devices.
SATA Speed
Select Serial ATA device speed from Gen1 (1.5 Gbit/s), Gen2 (3 Gbit/s), Gen 3 (6
Gbit/s) or auto.
SATA Mode Selection
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller
Interface).
RAID Mode
This option allows you to create RAID using Intel® Rapid Storage Technology on the
Serial ATA devices. For more information, please see Chapter 9 - RAID.
Serial ATA Port 0 to 5 and Hot Plug
Enable or disable each Serial ATA port and its hot plug function.
Note that for SD330-H110, the SATA port will be numbered from 0 to 3. And for
SD330-Q170, it will be numbered from 0 to 4 (port 4 controls the signal of the Mini PCIe
slot).
Legacy USB Support
Disabled
Disable USB keyboard/mouse/storage support.
Enabled
Enable USB keyboard/mouse/storage support.
UEFI Only
Enable USB keyboard/mouse/storage support only under the UEFI environment.
XHCI Hand-off
Enable this item for operating systems that do not support xHCI Hand-off. The XHCI
ownership change will be claimed by the XHCI driver.
54
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PCI Express Configuration
This section configures the settings of PCI Express root ports.
PCI Express Configuration
For each PCIe root port above, configure the following parameters:
Select a PCI Express root port and press “Enter” to configure.
Enable/Disable
PCI Express Root Port
Enable or disable this PCI Express root port.
PCIE
PCIE
PCIE
PCIE
Intel
Intel
PCIe Speed
1: PCIE1
2: PCIE2
3: PCIE3
4: PCIE4
I210AT
I219LM
slot
slot
slot (Note for SD330-Q170, this will be the full-size Mini PCIe slot)
slot (Note this is only available for SD331-C236/Q170)
Select the speed of the PCI Express root port: Auto, Gen1 (2.5 GT/s), Gen2 (5 GT/s) or
Gen3 (8 GT/s).
Hot Plug
Enable or disable the hot plug function of the PCIe root port.
55
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
ME Configuration
Active Management Technology Support
This section configures flashing of the Intel® Management Engine.
The section allows you to enable or disable the Intel® Active Management Technology (Intel®
AMT) BIOS extension. Refer to Chapter 10 - Intel AMT Settings for more information. Note
that this function is not available for the Intel® Core™ i3, Intel® Pentium®, Intel® Celeron®
processors or the Intel® H110 chipset.
Me Fw Image Re-Flash
Enable or disable Intel® Management Engine firmware flashing when updating the BIOS.
Intel AMT Support
Enable or disable Intel® Active Management Technology BIOS extension.
Un-Configure ME
Clears all ME related configurations without requiring a password on the next boot.
56
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Device Manager
Network Device List
This Device Manager menu is used to configure UEFI network settings when the “Network
Stack” is enabled in the “Dual” or “UEFI” boot mode or when the PXE Boot to LAN is enabled
in the “Legacy” boot mode. Refer to the “Boot” section in this chapter. After this function is
selected, the screen will warn you that you are going to exit the BIOS setup utility.
The “Device Manager” screen is displayed. And if the “Network Stack” or the “PXE Boot
to LAN” option is enabled from the “Boot” menu, the “Network Device List” should
be shown in the “Device list”. Select “Network Device List” to view all of the detected
network devices. For each network device, you can select to view and configure its
settings. In addition, you can select either the IPv4 or IPv6 network settings for UEFI
network configuration.
NIC Configuration Menu
This screen shows hardware information for the Ethernet controllers and configures
their operation.
57
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Blink LEDs
IPv6 Network Configuration
Enter the duration (seconds) for the Ethernet’s ACT LED to blink to indicate its presence.
If you select to use IPv6 network settings, enter the Interface ID (64 bit).
Policy: Select either automatic or manual. And select "Advanced Configuration" to
configure IPv6 network address manually if the manual option is selected.
New IPv6 address: Enter the IP address for the network device in the IPv6 format:
x : x : x : x : x : x : x : x (x can be any hexadecimal value between 0 and FFFF). Place a
space to separate each IP address to enter more than one address.
New Gateway addresses: Enter gateway addresses in the IPv6 format.
New DNS addresses: Enter DNS (Domain Name System) server IP addresses in the IPv6
format.
NIC Configuration
This screen configures the Ethernet controller. Select the link speed from the following options: Auto Negotiated, 10Mbps Half, 10Mbps Full, 100Mbps Half, and 100Mbps Full.
IPv4 Network Configuration
This screen configures the IP addressing method (DHCP or static IP). For static IP addressing, configure the following:
Local IP address and subnet mask: Enter the IP address for the network device in the
IPv4 format:
x . x . x . x (x must be a decimal value between 0 and 255).
Local Gateway: Enter the gateway address in the IPv4 format.
Local DNS (Domain Name System) Servers: Enter DNS (Domain Name System) server IP
addresses in the IPv4 format.
58
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Super IO Configuration
This section configures the system super I/O chip parameters.
COM Port 1 and COM Port 6
Enable or disable each serial port.
SYS Smart Fan/CPU Smart Fan/SYS Smart Fan 2 Control
Disable Disable this serial port.
Enable or disable the smart fan control.
Enable
Enable this serial port.
It also shows the Base I/O address and the assigned interrupt number.
Boundary 1 to Boundary 4
For COM Port 1 and COM Port 2, you can enable or disable the RS485 auto flow mechanism.
Set the boundary temperatures that determine the operation of the fan with different
fan speeds accordingly. For example, when the system or the CPU temperature reaches
boundary temperature 1, the system or CPU fan should be turned on and operate at
the designated speed.
WDT
Enable or disable the watchdog function. A counter will appear if you select to enable WDT.
Input any value between 1 and 255.
The range of the temperature is from 0 to 127oC.
Case Open
Fan Speed Count 1 to Fan Speed Count 4
Enable or disable the case open function.
Set the fan speed. The range is from 1 (lowest speed)-100% (full speed).
59
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
PC Health Status
This section displays PC health information such as the voltages and CPU and system temperatures.
60
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Console Redirection
COMA to COMF/PCI Serial Port
Enable or disable the serial redirection function for each of the serial ports on the system. And configure the serial communication parameters to be used between the system
and a remote station.
Console redirection lets you monitor and control the system from a remote station by re-directing the host screen output through a serial port.
UseGlobalSetting
Choose to use the pre-configured global settings from the previous menu or configure a
different setting for each serial port.
Console Serial Redirect
Enable or disable the console redirection function. (The default is disabled.) If you select
to enable it, please configure the following parameters for serial communication between
the system and a remote station:
Terminal type: VT_100, VT_100+, VT_UTF8, or PC_ANSI.
Baud rate: 115200, 57600, 38400, 19200, 9600, 4800, 2400 or 1200.
Data bits: 8 bits or 7 bits.
Parity: None, Even or Odd.
Stop bits: 1 bit or 2 bits.
Flow control: None, RTS/CTS or XON/XOFF
This is the global setting for all of the designated serial ports for the console redirection
function.
61
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Security
This section configures the security for the BIOS Setup utility and the optional Trusted Platform
Module (TPM) function.
TPM Availability
Set Supervisor Password
Show or hide TPM availability and its configurations.
Set the administrative password for entering the BIOS utility or upon entering the
power-on self-test (POST) process. The length of the password must be greater than 1
character and less than or equal to 10 characters.
TPM Operation
Enable or disable the TPM function. It displays the following options:
• No Operation: No changes to the current state.
• Disable: Disable and deactivate TPM.
• Enable: Enable and activate TPM.
Power-on Password
If you select to set the supervisor password, this option will be shown. Enable or disable
prompt for password at boot.
Clear TPM
Remove all TPM ownership contents.
62
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Boot
Boot Device Priority
This section configures legacy or EFI boot order or both depending on the “Boot Type” selected.
This section configures boot options.
Numlock
Select the power-on state for the Num Lock key.
Boot Type
Select the boot type. The options are Dual Boot, Legacy Boot and UEFI Boot Type.
Network Stack
This option is shown only when the boot type is set to Dual or UEFI.
Enable or disable UEFI network stack. It supports the operation of these functions or
software: Windows 8 BitLocker Network Unlock, UEFI IPv4/IPv6 PXE and legacy PXE
option ROM.
If this function is enabled, you can then go to “Advanced”>”Device Manager” to configure network settings for network connection under the UEFI environment.
PXE Boot Capability (UEFI mode) /PXE Boot to LAN (Legacy mode)
EFI Boot Menu
Use + and - keys to arrange the priority of the boot devices in the list.
Legacy Boot Menu
Normal
For this option, determine the boot order for the devices within each category. Use the
+ and - key to arrange the priority of the boot type devices in the list. The first device
in the list has the highest boot priority.
Advance
For this option, determine the boot order for all bootable devices. Use + and - keys to
arrange the priority of the detected boot devices in the list. The first device in the list
has the highest boot priority.
Enable or disable Preboot eXecution Environment (PXE) boot to LAN. In the UEFI or
Dual boot mode, this function can only be enabled if the Network Stack support is
enabled.
USB Boot
Enable or disable booting to USB boot devices.
63
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Exit
This section configures the parameters for exiting the BIOS setup utility.
Exit Saving Changes
Select this field and press <Enter> to exit BIOS setup and save your changes.
Load Optimal Defaults
Select this field and press <Enter> to load the optimal defaults.
Discard Changes
Select this field and press <Enter>to exit the BIOS setup without saving your changes.
Save Setting to file
Select this option to save BIOS configuration settings to a USB drive. The operation will
fail if there aren’t any USB devices detected on the system. The saved configuration will
have the DSF file extension and can be used for restoration.
Restore Setting from file
Select this option to restore BIOS configuration settings from a USB drive. Note that this
option will not be available if there aren’t any USB devices detected on the system.
64
Chapter 7 BIOS Setup
www.dfi.com
Chapter 7
Updating the BIOS
Notice: BIOS SPI ROM
To update the BIOS, you will need an updated BIOS file and a flash utility. Please contact
technical support or your sales representative for the files and specific instructions on how to
update BIOS with the flash utility.
1. The Intel® Management Engine has already been integrated into this system board. Due to
safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and
used on another system board of the same model.
When you download the given BIOS file, you may find a BIOS flash utility attached with the
BIOS file. This is the utility for performing the BIOS update procedure. For your convenience,
we will also provide you with an auto-execution file in the BIOS file downloaded. This autoexecution file will bring you directly to the flash utility menu soon after system boots up and
finishes running the boot files in your boot disk.
2. The BIOS (SPI ROM) on this system board must be the original equipment from the factory
and cannot be used to replace one which has been utilized on other system boards.
RRead file successfully.
3. If you do not follow the methods above, the Intel® Management Engine will not be updated
and will cease to be effective.
(path= “platform.ini”)
Information
Please do not remove the AC power
Note:
a. You can take advantage of flash tools to update the default configuration of the
BIOS (SPI ROM) to the latest version anytime.
b. When the BIOS IC needs to be replaced, you have to populate it properly onto the
system board after the EEPROM programmer has been burned and follow the
technical person's instructions to confirm that the MAC address should be burned
or not.
Insyde H20FFT (Flash Firmware Tool) Version (SEG) 100.00.08.10
Copyright(c) 2012 - 2017, Insyde Software Corp. All Rights Reserved.
Initializing
Current BIOS Model name: SD330
New BIOS Model name: SD330
Current BIOS version: B17A.31A
New BIOS version: B18A.31A
Updating Block at FFFFF000h
0%
25%
50%
75%
C:\SD330>_
100%
100%
65
Chapter 7 BIOS Setup
www.dfi.com
Chapter 8
Chapter 8 - Supported Software
The system requires you to install drivers for some devices to operate properly. To download
the latest driver, please go to the DFI Download Center:
http://www.dfi.com/DownloadCenter
Once you are in the Download Center page, select your product or type the model name and
click "Search" to find product-related resources such as documentation and drivers.
Drivers are available for the following devices in Windows 10:
•
Intel Chipset Device Software
•
Intel® Graphics Driver
•
Intel® LAN Driver
•
Kernel Mode Driver Framework (For Windows 7 only)
•
Intel® ME Driver
•
Intel® USB 3.0 Driver (For Windows 7 and Windows 8.1)
•
Audio Driver
•
Intel® Serial IO Driver
66
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Chipset Device Software
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
Please wait while the installation is in progress.
The Intel® Chipset Device Software is used for updating Windows® INF files so that the Intel
chipset can be recognized and configured properly in the system.
To install the utility, follow these steps:
1. Setup is ready to install the
utility. Click “Next”.
4. Please wait while the installation is in progress.
2. Read the license agreement,
and then click “Yes”.
5. Click “Restart Now” to allow
the new software installation to take effect.
67
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Graphics Driver
3. Go through the readme
document for system requirements and installation
tips, and then click “Next”.
To install this driver, follow these steps:
1. Setup is now ready to
install the graphics driver.
Click “Next”.
4. Setup is now installing the
driver. Click “Next” to continue.
By default, the “Automatically run WinSAT and enable the Windows Aero desktop theme” is
enabled. When this is enabled and after the system reboots, the screen will turn blank for
1 to 2 minutes (while WinSAT is running) before the Windows 7/ Windows 8.1/ Windows
10 desktop appears. The “blank screen” period is the time Windows is testing the graphics
performance.
We recommend that you skip this process by disabling this function and then click “Next”.
2. Read the license agreement, and then click “Yes”.
5. Click “Yes, I want to restart
this computer now”, and
then click “Finish”.
Restarting the system will
allow the new software
installation to take effect.
68
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel LAN Driver
4. Click “Install” to begin the
installation.
To install this driver, follow these steps:
1. Setup is preparing to install
the driver. Click “Next” to
continue.
5. After the installation is
complete, click “Finish”.
2. Click “I accept the terms in
the license agreement” if
you accept the agreement,
and then click “Next”.
3. Select the program features
you want to install, and
then click “Next”.
69
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Kernel Mode Driver Framework (For Windows 7 only)
Intel USB 3.0 Driver (For Windows 7 and Windows 8.1)
To install this driver, follow these steps:
To install the driver, click “Intel USB 3.0 Driver” on the main menu.
1. Click “Yes” to start the installation.
1. Setup is ready to install the driver.
Click “Next” to continue.
2. The update is installed now.
2. Read the license agreement, and
then click “Yes”.
3. Click “Restart Now“ to
restart your computer when
the installation is complete.
3. Wait while the setup is installing
the driver. After the installation is
complete, click “Finish”.
70
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel ME Driver
3. Setup is currently installing
the driver. After the installation is complete, click
“Next.”
To install the Intel® Management Engine (Intel® ME) Driver, follow these steps:
1. You are about to install
the driver. Click “Next”
to continue.
4. Please wait while the product is being installed.
2. Read the license agreement, and then click “Next”.
5. After the installation is
complete, click “Finish”.
71
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Audio Driver
Serial IO Driver
To install this driver, follow these steps:
To install this driver, follow these steps:
1. Setup is now ready to install the
audio driver. Click “Next”.
1. Setup is ready to install the driver.
Click “Next” to continue.
2. Follow the steps of the on-screen
instructions; click “Next” each
time you finish a step.
3. Click “Yes, I want to restart my
computer now”, and then click
“Finish”.
2. Read the license agreement carefully.
Click “I accept the terms in the
License Agreement” if you agree with
the terms in the agreement and then
click “Next”.
Restart the system to allow the new
software installation to take effect.
72
Chapter 8 Supported Software
www.dfi.com
Chapter 8
5. Setup is now installing the driver.
3. Read the file information and then
click “Next”.
4. Setup is ready to install the driver.
Click “Next” to begin the installation.
6. Click “Finish” to exit the setup.
73
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Intel Rapid Storage Technology
Infineon TPM 1.2 Driver and Tool (optional)
The Intel Rapid Storage Technology is a utility that allows you to monitor the current
status of the SATA drives. It enables enhanced performance and power management for
the storage subsystem.
To install this driver, follow these steps:
To install the driver, please refer to Chapter 9 for more information.
1. The setup program is preparing
to install the driver.
2. The setup program is now ready
to install the utility. Click “Next”
to continue.
74
Chapter 8 Supported Software
www.dfi.com
Chapter 8
3. Click “I accept the terms in the
license agreement” if you accept
the license agreement and then
click “Next”.
5. Select a setup type and then click
“Next”.
4. Enter the necessary information
and then click “Next”.
6. Click “Install” to start the
installation.
75
Chapter 8 Supported Software
www.dfi.com
Chapter 8
7. TPM requires installing the Microsoft Visual C++ package prior to
installing the utility. Click “Install”.
10. Click “Yes“ to restart your system.
8. The setup program is currently
installing the Microsoft Visual
C++ package.
9. Click “Finish”.
76
Chapter 8 Supported Software
www.dfi.com
Chapter 8
Windows TPM 2.0 Hotfix (For 64-bit Windows 7 only)
To install this driver, follow these steps:
1. Click “Yes“ to start the installation.
2. The update is being installed now.
3. Click “Restart Now“ to
restart your computer when
the installation is complete.
77
Chapter 8 Supported Software
www.dfi.com
Chapter 9
Chapter 9 - RAID
Settings
The system board allows RAID configuration with levels of RAID 0, RAID 1, RAID 5. Note that
SKUs with the Intel® H110 chipset do not support RAID.
To enable the RAID function, the following settings are required.
1. Connect the Serial ATA drives.
2. Enable RAID in the BIOS.
RAID Levels
3. Create a RAID volume.
RAID 0 (Striped Disk Array without Fault Tolerance)
4. Install the Intel Rapid Storage Technology Utility.
RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved
stacks. Data is divided into stripes and each stripe is written alternately between two disk drives.
This improves the I/O performance of the drives at different channel; however it is not fault tolerant. A failed disk will result in data loss in the disk array.
Step 1: Connect the Serial ATA Drives
RAID 1 (Mirrored Disk Array with Fault Tolerance)
Refer to Chapter 3 for details on connecting the Serial ATA drives.
RAID 1 copies and maintains an identical image of the data from one drive to the other drive. If
a drive fails to function, the disk array management software directs all applications to the other
drive since it contains a complete copy of the drive’s data. This enhances data protection and
increases fault tolerance to the entire system. Use two new drives or an existing drive and a new
drive but the size of the new drive must be the same or larger than the existing drive.
Important:
1. Make sure you have installed the Serial ATA drives and connected the data cables
otherwise you won’t be able to enter the RAID BIOS utility.
2. Treat the cables with extreme caution especially while creating RAID. A damaged
cable will ruin the entire installation process and operating system. The system will
not boot and you will lost all data in the hard drives. Please give special attention
to this warning because there is no way of recovering back the data.
RAID 5 (Striped Disk Array with Distributed Parity)
RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides
better hard drive performance and higher disk utilization than RAID 1.
Step 2: Enable RAID in the BIOS
RAID Level
Min. Drives
Protection
Description
RAID 0
2
None
Data striping without redundancy
2. Go to “Advanced” menu, and select the “SATA Configuration” menu.
RAID 1
2
Single Drive Failure
Disk mirroring
3. Change the “SATA Mode Selection” to “RAID” mode.
Single Drive Failure
Block-level data striping with
distributed parity
4. Save the changes in the “Exit” menu.
RAID 5
3
1. Power on the system then press <Del> to enter the main menu of the BIOS.
5. Reboot the system.
78
Chapter 9 RAID
www.dfi.com
Chapter 9
Step 3: Create a RAID Volume
Step 3-1: Create a RAID Volume if the boot type is UEFI
1. When the Intel RST option ROM status screen displays during POST, press <Ctrl> and
<I> simultaneously to enter the option ROM user interface.
If the boot type is set to UEFI, RAID volume creation will be different. Please use the following steps to create RAID volumes. To set the boot type, enter the BIOS utility and go to “Boot”
>”Boot type”.
®
2. Select 1: Create RAID Volume and press <Enter>.
3. Use the up or down arrow keys to select the RAID level and press <Enter>.
1. In the BIOS, go to the “Advanced” > “Device Manager”.
4. Use the up or down arrow keys to select the strip size and press <Enter>.
5. Press <Enter> to select the physical disks.
6. Use the up or down arrow keys to scroll through the list of hard drives and press <Space>
to select the drive.
7. Press <Enter>.
8. Select the volume size and press <Enter>. You must select less than one hundred percent
of the available volume space to leave space for the second volume.
9. Press <Enter> to create the volume.
10. At the prompt, press <Y> to confirm volume creation.
11. Select 4: Exit and press <Enter>.
12. Press <Y> to confirm exit.
2. Select Device Manager. The system will prompt you that it is going to exit the BIOS utility.
Select “OK” to continue.
Note:
These steps are cited from the Intel® Support site, “Set Up a System with Intel®
Matrix RAID Technology” (Article ID: 000005789).
3. The “Intel® Rapid Storage Technology” menu appears. Enter this menu.
79
Chapter 9 RAID
www.dfi.com
Chapter 9
Step 4: Install the Intel Rapid Storage Technology Utility
3. The screen displays all available drives. Select “Create RAID volume” to create a RAID
volume”.
The Intel Rapid Storage Technology Utility can be installed from within Windows. It allows
RAID volume management (create, delete, migrate) from within the operating system. It will
also display useful SATA device and RAID volume information. The user interface, tray icon
service and monitor service allow you to monitor the current status of the RAID volume and/or
SATA drives. Furthermore, It enables enhanced performance and power management for the
storage subsystem.
4. Use the up or down arrow keys to select the RAID level and press <Enter>.
5. Use the up or down arrow keys to scroll through the list of hard drives and press <Enter>
and select “x” to select the drive for the RAID group.
7. Use the up or down arrow keys to select the strip size and press <Enter>.
1. Insert the provided DVD into an optical drive.
8. Enter the capacity for the volume and press <Enter>.
2. Click “Intel Rapid Storage Driver” on the main menu.
9. Select “Create Volume” to start creating the volume.
3. Setup is ready to install
the utility. Click “Next” to
continue.
4. Read the license agreement and click “I accept
the terms in the License
Agreement“ if you accept
the agreement. Then, click
“Next”.
80
Chapter 9 RAID
www.dfi.com
Chapter 9
5. Go through the readme
document to view system
requirements and installation information, then click
“Next”.
8. Click “Yes, I want to restart
this computer now” to
complete the installation
and click “Finish”.
6. Click “Next” to install to
the default folder or click
“change” to choose another
destination folder.
Enable Intel Smart Response Technology
Intel® Rapid Storage Technology (Intel® RST) comes with a caching feature, Intel® Smart Response Technology, to improve system performance with an SSD used as cache memory.
To use this features, the following requirements have to be met:
*Intel RST software 10.5 version release or later
*Single hard disk drive or multiple drives in one RAID volume
*Solid state drive (SSD) with a minimum capacity of 18.6 GB
*Operating system: Windows 7 (32-bit and 64-bit editions) or later versions
Before using this function, set up your system with the following methods:
1. Configure SATA mode in BIOS setup. Please refer to the previous section on Intel Rapid
Storage Technology for detailed instructions.
7. Confirm the installation and
click “Next”.
2. Install the operating system and all required device drivers.
3. Install the Intel RST software version 10.5 or later.
4. Enable Intel Smart Response Technology, which is denoted as accelerate in the Intel RST
software.
Note:
The above information is cited from the Intel® Support site, “Intel® Smart Response Technology User Guide” (Article ID: 000005501).
81
Chapter 9 RAID
www.dfi.com
Chapter 10
6
Chapter
Chapter 10 - Intel AMT Settings
Enable Intel® AMT in the Insyde BIOS
Overview
1. Power on the system then press <Del> to enter the main menu of the BIOS setup utility.
Intel Active Management Technology (Intel AMT) combines hardware and software solutions
to provide maximum system defense and protection to networked systems. Note that the SKUs
with the Intel® H110 chipset or the Intel® Core™ i3, Celeron® and Pentium® processors do not
support iAMT.
2. In the “Advanced” menu, select “Active Management Technology Support”.
®
The hardware and software information are stored in non-volatile memory. With its built-in
manageability and latest security applications, Intel® AMT provides the following functions.
• Discover
Allows remote access and management of networked systems even while PCs are powered off;
significantly reducing desk-side visits.
• Repair
Remotely repair systems after OS failures. Alerting and event logging help detect problems
quickly to reduce downtime.
• Protect
Intel AMT’s System Defense capability remotely updates all systems with the latest security
software. It protects the network from threats at the source by proactively blocking incoming
threats, reactively containing infected clients before they impact the network, and proactively
alerting when critical software agents are removed.
3. In the “Active Management Technology Support” menu, select “Enabled” for
“Intel AMT Support”.
82
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
Set up Intel® AMT using the Intel® Management
Engine BIOS Extension (MEBX)
4. In the “Exit” menu, select “Exit Saving Changes” and then select “OK”.
1. After the system reboots, press <Del> to enter the BIOS menu again.
2. In the “Advanced” menu, select “MEBX Configuration” to enter the Manageability Engine
BIOS Extension (MEBx) Setup.
3. When the system reboots, you will be prompted for a password. The default password is
“admin”. Enter the default password in the space provided under Intel(R) ME Password,
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
83
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
4. Enter a password in the space provided under “Intel(R) ME Password” and then press
“Enter”. The password must include:
•
•
•
•
•
5. You will be asked to verify the password. Enter the same new password in the space provided under “Verify Password” and then press “Enter”.
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
Verify Password
MEBx Login
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
Intel(R) ME Password
Intel (R) ME Password
[↑↓] = Move Highlight
Intel(R) ME Password
[↑↓] = Move Highlight
[Enter] = Select Entry
[Enter] = Select Entry
[Esc]= Exit
6. Select “Intel(R) ME General Settings” and then press “Enter”.
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
84
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
7. Select “Change Intel(R) ME Password” and then press “Enter”.
8. Select “Local FW Update” and then press “Enter”. Select “Enabled” or “Disabled” or
“Password Protected” and then press “Enter”.
You will be prompted for a password. The default password is “admin”. Enter the default
password in the space provided under “Intel(R) ME New Password” and then press “Enter”.
•
•
•
•
•
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
8-32 characters
Strong 7-bit ASCII characters excluding : , and ” characters
At least one digit character (0, 1, ...9)
At least one 7-bit ASCII non alpha-numeric character, above 0x20, (e.g. !, $, ;)
Both lower case and upper case characters
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Disabled
Enabled
Password Protected
INTEL (R) ME PLATFORM CONFIGURATION
Change ME Password
Local FW Update
<Enabled>
<Enabled>
Intel(R) ME New Password
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
9. Select Previous Menu until you return to the “Main Menu”. Select “Intel(R) AMT Configuration” and then press “Enter”.
Intel (R) ME New Password
[↑↓] = Move Highlight
[Enter] = Select Entry
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
MAIN MENU
[Esc]= Exit
> Intel(R) ME General Settings
> Intel(R) AMT Configuration
MEBx Exit
[↑↓] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
85
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
10. In the “Intel(R) AMT Configuration” menu, select “Manageability Feature Selection” and
then press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
12. In the “SOL/Storage Redirection/KVM” menu, select “Username and Password” and then
press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Disabled
Activate Network Access
Enabled
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Username and Password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Anytime>
<Full Unprovision>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
13. In the “SOL/Storage Redirection/KVM” menu, select “SOL” and then press “Enter”. Select
“Enabled” or “Disabled” and then press “Enter”.
11. In the “Intel(R) AMT Configuration” menu, select “SOL/Storage Redirection/KVM” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
INTEL (R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
< Enabled>
<Enabled>
<Enabled>
<Enabled>
< Enabled>
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Anytime>
<Full Unprovision>
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Select Entry [Esc]= Exit
86
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
14. In the “SOL/Storage Redirection/KVM” menu, select “Storage Redirection” and then press
“Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
16. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“User Consent” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
INTEL(R) AMT CONFIGURATION
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
< Enabled>
<Enabled>
<Enabled>
<Enabled>
Manageability Feature Selection
> SOL/Storatge Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Netwok Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
<Anytime>
<Full Unprovision>
[↑↓] =Move Highlight [Enter] =Select Entry [Esc] =Exit
15. In the “SOL/Storage Redirection/KVM” menu, select “KVM Feature Selection” and then
press “Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
17. In the “User Consent” menu, select “User Opt-in” and then press “Enter”. Select “None”,
“KVM” or “ALL” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved
SOL/Storage Redirection/KVM
Username and password
SOL
Storage Redirection
KVM Feature Selection
<Enabled>
USER CONSENT
< Enabled>
<Enabled>
<Enabled>
<Enabled>
User Opt-in
Opt-in Configurable from Remote IT
< KVM>
< Enabled>
NONE
KVM
ALL
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
87
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
20. In the “Intel(R) AMT Configuration” menu, select “Network Setup” and then press “Enter”.
18. In the “User Consent” menu, select “Opt-in Configurable from Remote IT” and then press
“Enter”. Select “Enabled” or “Disabled” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
USER CONSENT
User Opt-in
Opt-in Configurable from Remote IT
< ALL>
< Enabled>
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Disabled
Enabled
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[↑↓] =Move Highlight
<Enabled>
<Anytime>
<Full Unprovision>
[Enter] =Select Entry
[Esc] =Exit
21. In the “Intel(R) ME Network Setup” menu, select “Intel(R) ME Network Name Settings”
and then press “Enter”.
19. Select Previous Menu until you return to the “Intel(R) AMT Configuration” menu. Select
“Password Policy” and then press “Enter”.
You may choose to use a password only during setup and configuration or to use a password anytime the system is being accessed.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK SETUP
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
> Intel(R) ME Network Name Settings
> TCP/IP Settings
Manageability Feature Selection
<Enabled>
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
<Anytime>
> Network Setup
Activate Network Access
Unconfigure Network Access
<Full Unprovision>
> Remote Setup And Configuration
> Power Control
Default Password Only
During Setup And Configuration
Anytime
[↑↓] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
88
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
22. In the “Intel(R) ME Network Name Settings” menu, select “Host Name” and then press
“Enter”. Enter the computer’s host name and then press “Enter”.
24. Select “Shared/Dedicated FQDN” and then press “Enter”. Select “Shared” or “Dedicated”
and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
INTEL (R) ME NETWORK NAME SETTINGS
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
Dedicated
Shared
Computer Host Name
[Enter] =Complete Entry
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
[Esc] =Discard Changes
23. Select “Domain Name” and then press “Enter”. Enter the computer’s domain name and
then press “Enter”.
25. Select “Dynamic DNS Update” and then press “Enter”. Select “Enabled” or “Disabled” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) ME NETWORK NAME SETTINGS
INTEL (R) ME NETWORK NAME SETTINGS
Host Name
Domain Name
Shared/ Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Host Name
Domain Name
Shared/Dedicated FQDN
Dynamic DNS Update
_
_
<Shared>
<Disabled>
Computer Domain Name
_
_
<Shared>
<Disabled>
Disabled
Enabled
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[↑↓] = Move Highlight [Enter] = Complete Entry [Esc]= Discard Changes
89
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
26. Select Previous Menu until you return to the “Intel(R) ME Network Setup” menu. Select
“TCP/IP Settings” and then press “Enter”.
28. In the “Intel(R) AMT Configuration” menu, select “Activate Network Access” and then
select “Yes/No” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.5.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
TCP/IP SETTINGS
DHCP Mode
> Wired LAN IPV4 Configuration
<Enabled>
Disabled
Enabled
[↑↓] =Move Highlight
[Enter] =Select Entry
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[Esc] =Exit
27. In the “TCP/IP Settings” menu, select “Wired LAN IPV4 Configuration” and then press
“Enter”.
29. In the “Intel(R) AMT Configuration” menu, select “Unconfigure Network Access” and then
press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.5.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
WIRED LAN IPV4 CONFIGURATION
DHCP Mode
INTEL(R) AMT CONFIGURATION
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Enabled>
Disabled
Enabled
<Enabled>
<Anytime>
<Full Unprovision>
Full Unprovision
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
90
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
30. In the “Intel(R) AMT Configuration” menu, select “Remote Setup And Configuration” and
then press “Enter”.
32. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning Record” and
then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
Intel(R) Management Engine BIOS Extension v11.0.0.0010Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
[↑↓] =Move Highlight
INTEL(R) REMOTE SETUP AND CONFIGURATION
<Enabled>
<Anytime>
<Full Unprovision>
Provision Record is not present
[Enter] =Select Entry
[↑↓] =Move Highlight
[Esc] =Exit
31. In the “Intel(R) Remote Setup And Configuration” menu, select “Current Provisioning
Mode” and then press “Enter”.
[Enter] =Select Entry
[Esc] =Exit
33. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server IPV4/
IPV6”, enter “Provisioning server address” and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Provisioning server address
Provisioning Mode: PKI
[↑↓] = Move Highlight
[↑↓] =Move Highlight
[Enter] =Select Entry
[Enter] = Select Entry
[Esc]= Exit
[Esc] =Exit
91
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
36. In the “Intel(R) Remote Setup And Configuration” menu, select “TLS PKI” and then press
“Enter”.
34. In the “Intel(R) Remote Setup And Configuration” menu, select “Provisioning server
FQDN”, enter the FQDN of Provisioning server, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
INTEL (R) REMOTE SETUP AND CONFIGURATION
Current Provisioning Mode
Provisioning Record
Provisioning Server IPV4/IPV6
Provisioning Server FQDN
> RCFG
> TLS PKI
_
_
_
_
Enter FQDN of provisioning server
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
[↑↓] = Move Highlight
35. In the “Intel(R) Remote Setup And Configuration” menu, select “RCFG” and press “Enter”,
and then select “Start Configuration Y/N” and press “enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1205
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
INTEL(R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
Start Configuration
This will activate Remote Configuration. Continue: (Y/N)
[Enter] =Select Entry
[Esc]= Exit
37. In the “Intel(R) Remote Configuration” menu, select “Remote Configuration**” and press
“Enter”, and then select “Enabled” or “Disabled” and press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
[↑↓] =Move Highlight
[Enter] = Select Entry
< Enabled>
_
Disabled
Enabled
[↑↓] = Move Highlight
[Esc] =Exit
[Enter] = Select Entry
[Esc]= Exit
92
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
40. In the “Intel(R) Remote Configuration” menu, select the hash name then press Insert to
enter custom hash certificate name, press Delete to delete a hash, press Enter to view
hash information, or press + to activate or deactivate hash.
38. Select “PKI DNS Suffix”, enter the “PKI DNS Suffix”, and then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0005/Intel(R) ME v11.0.0.1197
Copyright(C) 2003-15 Intel Corporation. All Rights Reserved.
INTEL (R) REMOTE CONFIGURATION
Remote Configuration**
PKI DNS Suffix
> Manage Hashes
INTEL (R) REMOTE CONFIGURATION
< Enabled>
_
Hash Name
VeriSign Class 3
VeriSign Class 3
Go Daddy Class 2
Comodo AAA CA
Starfield Class 2
VeriSign Class 3
VeriSign Class 3
VeriSign Class 3
GTE CyberTrust G1
Baltimore Cyber Tr
Cyber Trust Global
Verizon Global Ro
Entrust. net CA (2
Entrust Root CA
VeriSign Universa
Go Daddy Root CA
Entrust Root CA Startfield Root CA
Enter PKI DNS Suffix
[↑↓] = Move Highlight
[Enter] = Select Entry
[Esc]= Exit
39. Select “Manage Hashes”, and then press “Enter”.
[Ins]= Add New Hash
[↑↓] =Move Highlight
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
[↑↓] =Move Highlight
[Delete] = Delete Hash
[Enter] = View Hash
Algorithm
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
SHA256
[+] = Activate Hash
[Esc]= Exit
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL(R) AMT CONFIGURATION
<Enabled>
_
[Enter] =Select Entry
Default
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
Default: [*]
41. In the “Intel(R) AMT Configuration” menu, select “Power Control”, and then press Enter.
INTEL(R) REMOTE CONFIGURATION
Remote Configuration **
PKI DNS Suffix
> Manage Hashes
Active
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Active: [*]
Manageability Feature Selection
> SOL/Storage Redirection/KVM
> User Consent
Password Policy
> Network Setup
Activate Network Access
Unconfigure Network Access
> Remote Setup And Configuration
> Power Control
<Enabled>
<Anytime>
<Full Unprovision>
[Esc] =Exit
[↑↓] =Move Highlight
[Enter] =Select Entry
[Esc] =Exit
93
Chapter 10 Intel AMT Settings
www.dfi.com
Chapter 10
6
Chapter
44. Press “Esc” until you return to the “Main Menu”. Select “MEBx Exit” then press “Enter”.
Press “Y” then press “Enter”.
42. In the “Intel(R) AMT Power Control” menu, select “Intel(R) AMT ON in Host Sleep States”
then press Enter. Select an option then press “Enter”.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
MAIN MENU
INTEL(R) AMT POWER CONTROL
> Intel (R) ME General Settings
> Intel (R) AMT Configuration
MEBx Exit
These configurations are effective only after AMT provisioning has started
Intel(R) AMT ON in Host Sleep States <Desktop: ON in S0, ME Wake in
S3, S4-5>
Idle Timeout
65535
Desktop: ON in S0
Desktop: ON in S0, ME Wake in S3, S4-5
[↑↓] = Move Highlight
[↑↓] =Move Highlight <Enter> =Complete Entry [Esc] =Discard Changes
[Enter] = Select Entry
[Esc]= Exit
43. In the “Intel(R) AMT Power Control” menu, select “Idle Timeout” and then press “Enter”.
Enter the timeout value (1-65535).
Intel(R) Management Engine BIOS Extension v11.0.0.0010/Intel(R) ME v11.8.50.3399
Copyright(C) 2003-16 Intel Corporation. All Rights Reserved.
INTEL (R) AMT POWER CONTROL
This configurations are effective only after AMT provisioning has started
Intel (R) ME ON in Host Sleep States
Idle Timeout
<Mobile: ON in S0,
ME Wake in S3, S4-5
(AC only)>
65535
Timeout Value (1-65535)
65535
[↑↓] =Move Highlight
<Enter> =Complete Entry [Esc] =Discard Changes
94
Chapter 10 Intel AMT Settings
www.dfi.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising