DFI | WM343-SD Installation Guide | manual | Dfi WM343-SD Installation Guide Manual

Dfi WM343-SD Installation Guide Manual
WM343-SD Series Installation Guide
Package Contents
• One WM343-SD330/WM343-SD331 system unit
• 1 SATA data cable
• 1 CPU cooler and 1 system fan
• HDD mounting screws
• 1 Quick Installation Guide
• 1 CD disk includes:
- Drivers / Manual
Panel
Front View
Rear View (WM343-SD330/WM343-SD331)
Optical drive bay
(optional)
Expansion card slot
SATA
drive bay
PS/2 KB/MS
USB 2.0
LAN 1 LAN 2
USB 3.0 1-4
COM1
Line-in (optional)
Line-out
VGA DVI-I
Mic-in
(DVI-D signal)
DP++
DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and for a more
details of the installation process, please refer to the user's manual on the website.
www.dfi.com
1
Opening the Chassis
Please observe the following guidelines and follow the procedure to open
the system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. Remove the top cover by uninstalling the thumb screws.
Thumb screw
2
Installing a DIMM
To access the DIMM sockets, first remove the CD tray by uninstalling the screws
from the rear panel and inside the chassis.
CD tray screw
CD tray screw
3
1. Align the notch on the DIMM with the tab in the DIMM connector.
2. Press down on the DIMM until the release tabs spring back to secure the
DIMM in place.
The installed DIMM
Notes:
1. The WM343-SD330 is equipped with two or four DDR4 (dual channel) sockets depending
on the chipset.
2.
The WM343-SD331 is equipped with four DDR4 (dual channel) sockets.
4
Installing a 3.5" SATA Drive
1. Remove the thumb screws that secure the HDD drive bay to the chassis and
remove the drive bay.
Thumb screw
2. Secure the hard drive to the drive bay. Align the mounting holes on the SATA
drive with the mounting holes on the HDD drive bay. Use 4 mounting screws
to install the hard drive onto the HDD drive bay.
Mounting screw
Drive bay
Mounting screw
3.5" SATA Drive
5
Use the same HDD drive bay to secure a 2.5" hard disk to the system. Refer to the
pictures below for the location of mounting holes.
Mounting screw
Mounting screw
2.5" SATA Drive
3. Slide the HDD drive bay back to the system and secure it with the thumb screws.
4. Connect the SATA data cable and power cable to the connectors on the SATA
drive. And connect the other end of the SATA data cable on the motherboard.
SATA data and
power cable
SATA Port
6
Installing More Than One SATA Drive (Optional)
To install more than one 2.5" SATA drive, use the 5.25" optical drive bay. And to
install more than one 3.5" SATA drive, order another HDD drive bay, which will
replace the optical bay in the system.
Use the following procedure to install a second and third 2.5" HDD/SSD:
1. Attach 4 standoffs to the 2.5" HDD or SSD.
Mounting screw
Mounting screw
2. Secure the hard drive to the optical drive bay. Align the standoffs on the HDD
with the mounting holes on the optical drive bay. Use 4 mounting screws to
install the hard drive onto the optical drive bay.
Mounting screw
Mounting screw
7
3. Install the optical drive bay back to the system.
4. Connect the SATA data cable and power cable to the connectors on the SATA
drive. And connect the other end of the SATA data cable on the motherboard.
SATA data and
power cable
SATA data and
power cable
8
SATA Port
Installing a PCI or PCIe Expansion Card
Use the following procedure to install a PCIe expansion card:
1. Remove the mounting screws to uninstall the card slot bracket.
Card slot bracket
Screw
2. Insert the expansion card in the connector on the motherboard and press
down until secured.
PCIe card
9
3. Reinstall the card slot bracket to secure the expansion card in place.
Rear View
PCIe card
Notes:
1. The WM343-SD330 is equipped with one PCIe x16, one PCIe x4 and two PCI slots.
2.
The WM343-SD331 is equipped with two PCIe x16 and two PCIe x4 slots.
10
Installing a Mini PCIe Card
The system board is equipped with one Mini PCIe slot that uses USB, PCI
and mSATA signals.
1. Grasp the Mini PCIe card by its edges and align the notch in the
connector of the PCIe card with the notch in the connector on the
system board.
2. Push the Mini PCIe card down and use the provided mounting screws to
secure the card on the system board.
Mounting screw
Note:
The Mini PCIe slot is only available in WM343-SD330 (Intel® Q170 Chipset).
11
Board Layout and Jumper Settings (WM343-SD330)
WM343-SD330 (H110)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP10)
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
COM 1 RS232/Power
Select (JP9)
System Fan 1
1
1
PS/2 KB/MS
USB 6
USB 5
USB 2.0
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
1
5
14 13
+12V
Power
Chrontel
CH7517A
COM 1
RS232/422/485
Select (JP7)
CPU Fan
2
8
COM 1
VGA
WM343-SD330 (Q170)
Socket LGA1151
CPU Fan
2
6 2
6
1
2
5 1
6 2
5
6
1
5 1
4
5
COM 1 RS232/485
Select (JP8)
1
8
TPM
(optional)
COM 1
VGA
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
System Fan 1
COM 1 RS232/Power
Select (JP9)
Socket LGA1151
21
TPM
(optional)
21
LPC
LPC
ASMedia
ASM1442
12
ASMedia
ASM1442
24
DVI-D
DP++
12
24
DVI-D
DP++
ATX
Power
Intel
WGI219LM
1
LAN 1
USB 2
USB 1
Auto Power-on 1
Select (JP5) 1
3
12
1
2
8
1
SPI Flash
BIOS
DDR4_3
Line-out
Mic-in
Chassis
Intrusion
11
12
1
2
7
8
1
2
7
8 Header
LAN LED
Battery
1
J6
Clear CMOS
Data (JP1)
Clear CMOS
Data (JP1)
PCIe x16
DDR4_1
SPI Flash
BIOS
DDR4_3
DDR4_2
DDR4_4
Chassis
Intrusion
SPI
Program
JP6
PCIe x16
DDR4_1
2
7
1
2
Front
Panel
Intel
WGI210AT
USB 3.0
LAN LED
Battery
7
Line-out
Mic-in
Auto Power-on 1
Select (JP5) 1
LAN 2
USB 4
USB 3
8
USB 3.0
11
13
1
USB 3.0
2
Front
Panel
Intel
WGI210AT
Standby
Power LED
Intel
WGI219LM
LAN 1
USB 2
USB 1
13
1
J26
USB 3.0
LAN 2
USB 4
USB 3
ATX
Power
Standby
Power LED
1
1
PCI 1
Realtek
ALC888
1
PCI 2
1
H110
SATA 1
Buzzer
1
2
PCIe x4
1
39
Nuvoton
NCT6106D
2
40
LVDS LCD Panel
1
6
2
SMBus
1
19
USB 7-8
USB 9/10
1
2
4
LCD/Inverter Power
Clear CMOS Data
Normal (default)
Clear CMOS Data
9
1
10
2
1
1
9
6
5
2
1
2
6 2
6 2
1
5 1 5 1
1 9
6
9
1 9
2 10
COM 2
2 10
COM 3
2 10
COM 4
NXP
PTN3460
1
2 10
COM 5
RS232 (default)
RS422 Full Duplex
RS485
2
COM 6 System
Fan 2
JP7 (COM 1)
JP11 (COM 2)
1-2 On
3-4 On
5-6 On
JP8/JP10 (COM 1)
RS232/422/485 Select JP12/JP13 (COM 2)
RS232 (default)
1-3, 2-4 On
RS422 Full Duplex/RS485
3-5, 4-6 On
RS232/Power Select
RS232 (default)
RS232 with power
JP9 (COM 1)
JP14 (COM 2)
1-3 (RI), 2-4 (DCD) On
3-5 (+5V), 4-6 (+12V) On
Auto Power-on Select
Power-on via power button
(default)
Power-on via AC power
SATA 0
Q170
SATA 1
1
Backlight Power
Select (JP3)
JP1
1-2 On
2-3 On
RS232/422/485 Select
PCI 2
2
SATA 3
SATA 3.0
(JP11)
5
1 9
1
1
S/PDIF
COM 2 RS232/Power
Select (JP14)
SATA 2
1
10
1
Nuvoton
NCT6106D
Intel
Buzzer
1
(JP13)
USB 2.0
Digital I/O
SW1
4
ON
3
1
5
5
JP12
1
1
COM 2 RS232/Power
Select (JP14)
6
JP4
2
JP3
1
JP2
R507 R505
Realtek
ALC888
SATA 0
1
S/PDIF
Mini PCIe/mSATA 1
Signal Select (JP6)
PCI 1
1
Intel
JP5
1-2 On
2-3 On
Notes:
1. When COM 1 RS232/422/485 is selected,
JP8 and JP10 must be set in accordance to JP7.
2. When COM 2 RS232/422/485 is selected,
JP12 and JP13 must be set in accordance to JP11.
12
1
1
6
5
Panel Power Select (JP2)
PCIe x4
LCD/Inverter
Power Select (JP4) 1
1
2
Digital I/O
39
40
LVDS LCD Panel
5
ITE
IT8893E
1
19
LCD/Inverter Power
1
2
11
10
1
SMBus
6
6
SATA 2
1
2
5
2
1
2
6 2
6 2
6
1
5 1 5 1
(JP12)
1 9
5
(JP13)
USB 3.0
USB 2.0
USB 5-6
USB 9-10 USB 7-8
9
1
9
1
10
2
10
2
1
1
9
9
1 9
1 9
1
1
10
2 10
COM 2
2 10
COM 3
2 10
COM 4
Backlight Power Select
+3.3V (default)
+5V
JP3
1-2 On
2-3 On
Panel Power Select
+12V
+5V
+3.3V (default)
JP2
1-2 On
3-4 On
5-6 On
LCD/Inverter Power Select
+12V (default)
+5V
JP4
1-2 On
2-3 On
2 10
COM 5
The following jumper settings are for
WM343-SD330 (Q170) only.
Mini PCIe/mSATA Signal
Select
Mini PCIe (default)
mSATA
SATA 3
SATA 3.0
(JP11)
JP6
1-2 On
2-3 On
2
COM 6
System
Fan 2
WM343-SD331 (C236/Q170)
COM 1
RS232/422/485
Select (JP7)
PS/2 KB/MS
USB 6
USB 5
USB 2.0
2
6 2
6
1
COM 1 2
5 1
6 2
5
6
5 1
5
RS232/422/485
Select (JP10) 1
System Fan 2
1
8
5
14 13
+12V
Power
Chrontel
CH7517A
1
1
COM 1 RS232/422/485
Select (JP8)
4
COM 1
VGA
CPU Fan
COM 1 RS232/Power
Select (JP9)
Socket LGA1151
TPM
(optional)
21
LPC
ASMedia
ASM1442
12
DVI-D
DP++
24
Standby
Power LED
ATX
Power
LAN 1
USB 2
USB 1
Intel
WGI219LM
USB 3.0
13
1
Auto Power-on
Select (JP5)
LAN 2
USB 4
USB 3
1
1
Intel
WGI210AT
USB 3.0
2
Front
Panel
Battery
Line-out
Mic-in
Clear CMOS
Data (JP1)
1
11
12
1
2
LAN LED
DDR4_1
PCIe 1 (PCIe x16 or PCIe x8)
7
DDR4_3
DDR4_2
8
DDR4_4
SATA 3.0
1
Realtek
ALC888
1
1
PCIe 2 (PCIe x4)
SATA 1
SATA 0
Intel
S/PDIF
1
PCIe 3 (PCIe x8)
1
SATA 3
SATA 2
Q170
SATA 5
SATA 4
1
Nuvoton
NCT6106D
PCIe 4 (PCIe x4)
21
Chassis
Intrusion
USB 5-6
USB 3.0 11
10
21
65
COM 2 RS232/422/485
USB 2.0
Select (JP13)
COM 3
USB 9-10 USB 7-8 COM 2
USB 7-8
11
1 10
1
COM 2 RS232/422/485
6 5 Select (JP12) 6 5
6
5
COM 2 RS232/Power
Select (JP14)
2
1
9
1
9
1
9
1
9
5
COM 2 RS232/422/485
Select (JP11)
6
COM 4
1
System Fan 1
1
2
SPI Flash
BIOS
9
1 9
1
SMBus
21
1 9
1
1
Buzzer
19
1
10
2
10
2 10
RS232/422/485 Select JP7 (COM 1)
JP11 (COM 2)
RS232 (default)
1-2 On
RS422 Full Duplex
3-4 On
RS485
5-6 On
2 10
2 10
2 10
2 10
COM 5
2
RS232/Power Select
RS232 (default)
RS232 with power
RS232/422/485 Select JP8/JP10 (COM 1)
JP12/JP13 (COM 2)
RS232 (default)
1-3, 2-4 On
RS422 Full Duplex/RS485
3-5, 4-6 On
Notes:
1. When COM 1 RS232/422/485 is selected,
JP8 and JP10 must be set in accordance to JP7.
1
2
DIO
COM 6
JP9 (COM 1)
JP14 (COM 2)
1-3 (RI), 2-4 (DCD) On
3-5 (+5V), 4-6 (+12V) On
Clear CMOS Data
Normal (default)
Clear CMOS Data
Auto Power-on Select
Power-on via power button
(default)
Power-on via AC power
JP1
1-2 On
2-3 On
JP5
1-2 On
2-3 On
2. When COM 2 RS232/422/485 is selected,
JP12 and JP13 must be set in accordance to JP11.
www.dfi.com
13
A47300735
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising