Sena | R1 EVO | Quick Start Guide | Sena R1 EVO Quick Start Guide

Sena R1 EVO Quick Start Guide
SMART CYCLING HELMET
QUICK START GUIDE
1.0.0
ENGLISH
RIDE CONNECTED
The R1 EVO with built-in Bluetooth® capabilities
allows you to hear GPS navigation, take phone
calls and listen to your favorite tunes. You can
use the Mesh IntercomTM to communicate with
other R1 EVO users and use the LED Taillight to
ride safely.
Bluetooth® Integrated
Mesh Intercom™
900 meters (0.5 miles)*
LED Taillight
Voice Command
* in open terrain
GETTING STARTED
1.
This product comes with a Quick Start
Guide, which is a basic version of the
User’s Guide. A FULL VERSION OF THE
USER’S GUIDE CAN BE DOWNLOADED
AT Sena.com.
2.
Update this product for free with the latest
firmware to fully enjoy the new advanced
features built into this product. Visit
sena.com to see how to update your
product.
3.
Users can follow Sena on Facebook,
YouTube, Twitter and Instagram to
receive the most up to date information
on products, helpful tips and all other
announcements regarding Sena products.
SENA Technologies, Inc.
sena.com
Customer Support: support.sena.com
GETTING STARTED
Quick start guide
Product Details
(-) Button
Microphone
Speakers
Bluetooth
System's Buttons
Blue/Red/
Green
LED Lights
Center
Button
(+) Button
SENA Button
Fault Reset Button
DC Power Charging &
Firmware Upgrade Port
Quick start guide
Quick start guide
How To Fit the Helmet
1.
Position the helmet on your head with the
front covering your forehead.
2.
Position the strap adjuster centered, just
below your ears.
3.
Position the helmet low on your forehead
with the buckle under the chin and back
against the throat. The straps should fit
comfortably around both ears.
4.
After removing the chinstrap pad, adjust
the chinstrap tension at the buckle so
the chinstrap is tight and comfortable
by pulling the chinstrap end through
the buckle to either tighten or loosen as
needed.
Buckle
Chinstrap Pad
Strap Adjuster
Chinstrap
O-Ring
Quick start guide
5.
Secure the excess strap with O-ring and
then attach the chinstrap pad.
Note: Check the
chinstrap’s position and
tension regularly to ensure
proper fit.
6.
Turn the retention system knob clockwise
to tighten or counterclockwise to loosen.
7.
To change the height of the retention
system, firmly pull or push the retention
system upward or downward to a different
position.
Retention System Knob
Retention System
WARNING: For maximum protection, this helmet
must be fitted and attached properly to the wearer’s
head in accordance with the following instructions. If
after adjustment the helmet does not fit properly, do
not use the helmet. Return it to the retailer or Sena.
Quick start guide
Sena Cycling App
By simply pairing your phone with your headset, you can
use the Sena Cycling App for quicker and easier set up
and management.
• App Features: Mesh Intercom, Music, FM Radio, LED
Taillight, Device settings, Quick Start Guide, and User’s
Guide.
• Download
- Android: Google Play Store> ‘Sena Cycling’
- iOS: App Store > ‘Sena Cycling’
Sena Device Manager
The Sena Device Manager allows you to upgrade the
firmware and configure its settings directly from your PC
or Apple computer. Download the Sena Device Manager
from sena.com.
Quick start guide
Basic Operations
Powering On
Powering Off
HOLD
=
1s
Volume Up
=
TAP
=
1x
Visual Method
high
MED
LOW
=
=
=
1x
Volume Down
Checking the Battery Level
=
TAP
=
HOLD
1s
TAP
1x
Quick start guide
Phone Pairing
Mobile Phone Pairing
Press and hold the (+) Button and Center Button for
10 seconds when the R1 EVO is turned off.
=
=
LED
Status
=
pin
number
HOLD
10s
Alternating blue
and red flashing
lights indicate
device is now
discoverable.
Quick start guide
Mobile Phone
Answer a Call
=
TAP
1x
Make Call with
Voice Dialer
=
HOLD
3s
End/Reject a Call
=
HOLD
2s
Music Controls
Play/Pause
=
HOLD
1s
Next Track
=
Previous Track
HOLD
1s
=
HOLD
1s
Quick start guide
Mesh Intercom™
When Mesh Intercom is enabled, the R1 EVO will
automatically connect to nearby R1 EVO users and allow
them to talk to each other by pressing the Center Button.
Mesh Intercom On
=
Mesh Intercom Off
TAP
1x
“Mesh intercom on”
=
TAP
1x
"Mesh intercom off"
Mic Enable/Disable (Default: Enable)
Users can enable/disable the microphone when
communicating in a Mesh Intercom.
Enable/Disable the Microphone
=
HOLD
1s
Quick start guide
Channel Setting (Default: channel 1)
If the Mesh Intercom communication experiences interference
because other groups are also using the channel 1, change
the channel. You can select one of 1 to 9 channels.
Using the button
Enter into the Channel Setting
TAP
=
2x
“Channel setting, channel 1”
Navigate Between the Channel
(1 2 ••• 8 9 Exit 1
TAP
=
1x
or
“#”
Save the Channel
=
TAP
1x
"Channel is set, channel #"
•••)
=
TAP
1x
Quick start guide
Note: Exit the channel setting, tap the (+) Button or the
(-) Button until you hear a voice prompt, “Exit”, and tap
the Center Button.
Using the Sena Cycling App
You can select the channel through the Sena Cycling App.
Quick start guide
Radio
FM Radio Off
FM Radio On
=
HOLD
1s
Scan Stations
=
=
=
HOLD
1s
Seek Stations
HOLD
1s
HOLD
1s
TAP
=
2x
=
2x
TAP
Navigating Preset
Stations
=
HOLD
1s
Note: You can also use the Sena Device Manager or
the Sena Cycling App to save the preset stations.
Quick start guide
LED Taillight
Using the Voice Command
LED On
TAP
=
1x
=
“Taillight”
=
“Taillight”
or
“Hello Sena”
LED Off
TAP
=
1x
or
“Hello Sena”
Using the SENA Button
LED On and Solid
=
TAP
Night Flash
1s~
Day Flash
=
=
1x
TAP
1x
LED Off
TAP
1s~
1x
=
TAP
1x
Using the Sena Cycling App
You can control the LED Taillight through the Sena
Cycling App.
1s~
Quick start guide
Bluetooth System Configuration
Menu
Accessing the
Configuration Menu
=
HOLD
10s
Execute Menu Options
=
Navigating Between
Menu Options
TAP
=
1x
=
1x
TAP
TAP
1x
Troubleshooting
Factory Reset
=
Fault Reset
HOLD
10s
=
TAP
=
2x
=
1x
TAP
Note: Fault Reset
will not restore the
Bluetooth system to
factory default settings.
Quick REFERENCE
TYPE
OPERATION
BUTTON COMMANDS
HOLD
Power on
1s
TAP
Power off
Basic
Operations
1x
Volume up/down
Answer phone call
End/reject phone call
Mobile
Phone
TAP
1x
HOLD
2s
HOLD
Voice dial
3s
Play/Pause music
Track forward
TAP
1x
or
HOLD
1s
HOLD
1s
Music
Track back
HOLD
1s
Quick Reference
Quick REFERENCE
TYPE
OPERATION
BUTTON COMMANDS
Mesh Intercom
on/off
TAP
1x
HOLD
Mic enable/disable
Mesh
Intercom™
1s
TAP
Channel setting
2x
HOLD
FM radio on/off
1s
HOLD
Select preset
FM Radio
Seek forward/
backward
Scan up FM band/
stop scanning
LED Taillight
1s
TAP
2x
or
HOLD
1s
TAP
LED on and solid
1x
Night flash
1x
Day flash
1x
LED off
1x
TAP
TAP
TAP
D00161_1.0.0_EN_November2019
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising