Sena | BLUETOOTH® MIC & INTERCOM | User guide | Sena BLUETOOTH® MIC & INTERCOM User Guide

Sena BLUETOOTH® MIC & INTERCOM User Guide
Bluetooth® Mic & Intercom
User's Guide
www.sena.com
350
380
© 1998-2014 Sena Technologies Inc. All rights reserved.
Sena Technologies Inc. reserves the right to make any changes and improvements to its product
without prior notice.
Sena™ is a trademark of Sena Technologies Inc. or its subsidiaries in the USA and other countries.
SMH10™, SMH10R™, SMH5™, SMH5-FM™, SPH10™, EXPAND™, SPH10H™, SPH10H-FM™, SPH10S™,
SR10™, SR10i™, SM10™, GoPro® Pack™, Bluetooth Mic & Intercom™ are trademarks of Sena
Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express
permission of Sena.
GoPro® is a registered trademark of Woodman Labs of San Mateo, California. Sena Technologies,
Inc. (“Sena”) is not affiliated with Woodman Labs. The Sena Bluetooth Pack for GoPro® is an aftermarket accessory specially designed and manufactured by Sena Technologies, Inc. for the GoPro®
Hero3 allowing for Bluetooth capabilities.
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks
by Sena is under license. Other trademarks and tradenames are those of their respective owners.
1. INTRODUCTION ..............................................5
2. PACKAGE CONTENTS .....................................7
3. GETTING STARTED..........................................9
3.1 Installing the Bluetooth Mic & Intercom...........9
3.2 Connecting Your Headphones .......................... 11
3.3 Powering On/Off .................................................... 11
3.4 Voice Prompt ........................................................... 11
3.5 Volume Adjustment .............................................. 12
3.6 Using Internal/External Microphone............... 12
3.7 Function Priority ..................................................... 13
3.8 Charging .................................................................... 13
3.9 Low Battery Warning............................................. 14
3.10 Checking the Battery Level ................................. 14
3.11 Fault Reset................................................................. 15
4. CONFIGURATION SETTING..........................16
4.1
4.2
4.3
4.4
4.5
Mobile Phone Pairing ........................................... 17
Multipoint Pairing .................................................. 17
Phone Selective Pairing ....................................... 18
Media Selective Pairing ........................................ 18
Assigning Speed Dial ........................................... 18
4.6 Enabling/Disabling Voice Prompts .................. 19
4.7 Enabling/Disabling Sidetone ............................. 20
4.8 Enabling/Disabling Advanced Noise
Control ...................................................................... 20
4.9 Enabling/Disabling Auto Gain Control ........... 21
4.10 Delete All Bluetooth Pairing Information ..... 21
4.11 Reset to Factory Default Setting ...................... 22
4.12 Exit Voice Configuration Menu.......................... 22
5. PAIRING THE BLUETOOTH MIC &
INTERCOM WITH BLUETOOTH DEVICES ...24
5.1
5.2
5.3
5.4
Mobile Phone Pairing ........................................... 24
Multipoint Pairing .................................................. 25
Bluetooth Stereo Device Pairing ...................... 25
Pairing with the Bluetooth Pack for GoPro®
or PRISM..................................................................... 26
6. PAIRING WITH SELECTIVE PROFILE:
HFP OR A2DP STEREO..................................27
6.1 Phone Selective Pairing:
HFP for Phone Call Only ....................................... 27
6.2 Media Selective Pairing:
A2DP Stereo Music Only ...................................... 28
English
CONTENTS
7. STEREO MUSIC ..............................................29
8. MOBILE PHONE CALL MAKING AND
ANSWERING ..................................................30
8.1 Mobile Phone Call Making and
Answering ................................................................. 30
8.2 Speed Dialing .......................................................... 31
9. INTERCOM ......................................................33
9.1 Pairing with Other Bluetooth Mic &
Intercom for Intercom Conversation ............... 33
9.2 Pairing with Other Sena Headset Models
for Intercom Conversation .................................. 35
9.3 Two-way Intercom ................................................. 35
9.4 Three-way Conference Intercom ...................... 37
9.5 Four-way Conference Intercom ........................ 40
9.6 Intercom Failure ...................................................... 42
9.7 Intercom Reconnection ....................................... 42
10. UNIVERSAL INTERCOM..............................43
10.1 Universal Intercom Pairing.................................. 43
10.2 Two-way Universal Intercom.............................. 44
10.3 Three-way Universal Intercom .......................... 44
10.4 Four-way Universal Intercom ............................. 46
11. MUSIC SHARING .........................................50
12. FIRMWARE UPGRADE ................................51
13. SENA BLUETOOTH CONNECTION
CASE STUDIES.............................................52
Case 1................................................................................ 52
Case 2................................................................................ 53
14. OPERATION QUICK REFERENCE ...............54
CERTIFICATION AND SAFETY APPROVALS...55
t
t
t
t
t
t
t
FCC Compliance Statement ................................. 55
FCC RF Exposure Statement ................................ 56
FCC Caution ............................................................... 56
CE Declaration of Conformity ............................ 56
Industry Canada Statement ................................ 57
Bluetooth License ................................................... 57
WEEE (Waste Electrical and Electronic
Equipment) ................................................................ 58
SAFETY INFORMATION ....................................58
t Product Storage and Management.................. 58
t Product Use ............................................................... 59
t Battery......................................................................... 61
PRODUCT WARRANTY AND DISCLAIMER ....62
t
t
t
t
Limited Warranty..................................................... 62
Warranty Exclusions ............................................... 65
Warranty Service ..................................................... 68
Return for Full Refund ........................................... 68
Thank you for choosing the Sena Bluetooth Mic
& Intercom. The Sena Bluetooth Mic & Intercom
is an ultra-slim, light weight microphone that
allows users to make an intercom call. It may
function as a microphone when paired with the
Sena PRISM or Sena Bluetooth Audio Pack for
GoPro®. It also works as a headset and intercom
through the use of a pair of stereo headphones
with a built-in microphone that users may have.
As a Bluetooth microphone and intercom, it
allows for voice recording to accompany videos
as well as communicate with other Bluetooth
intercom. The Sena Bluetooth Mic & Intercom
allows for up to a four-way conference and
features voice prompts for ease of use.
The Bluetooth Mic & Intercom is compliant
with the Bluetooth 3.0 supporting the
following profiles: Headset Profile, Hands-Free
Profile (HFP), Advanced Audio Distribution
Profile (A2DP), and Audio Video Remote
Control Profile (AVRCP). Please check with the
manufacturers of other devices to determine
their compatibility with the Bluetooth Mic.
Please read this user’s guide carefully before
using the Bluetooth Mic. Also check www.
sena.com for the latest version of the user’s
guide and additional information related to
Sena Bluetooth products.
5
English
1. INTRODUCTION
The Bluetooth Mic & Intercom features:
x Bluetooth microphone for Bluetooth-ready
camera
x Bluetooth intercom up to 350 meters (380
yards)*
x Four-way conference intercom
x Advanced Noise Control™
x Multipoint Bluetooth for dual mobile
phone
x Bluetooth stereo headset for Bluetooth
audio devices such as MP3 players
x Bluetooth music playback control by
AVRCP
x Bluetooth handsfree for Bluetooth mobile
phones
x Voice prompts
x Crystal clear and natural sound quality
x Ultra-slim and feather light
x Durable, sweat and water resistant for
active condition
x Up to 6 hours talk time, 6 days stand-by
time
6
x Firmware upgradeable
Key Specifications:
x Bluetooth 3.0
x Supporting profiles: Headset Profile,
Hands-Free Profile (HFP), Advanced Audio
Distribution Profile (A2DP), Audio Video
Remote Control Profile (AVRCP)
* in open terrain
English
2. PACKAGE CONTENTS
Bluetooth Mic & Intercom
Status LED
Hi-Fi Microphone
Charging LED
Earbud Jack
(+) Button
Center Button
Power Switch
(-) Button
Micro-USB Charging Port
<Botton>
<Front>
7
Armband
Microphone Windscreens
Collar Clip
USB Power & Data Cable
The package does not include stereo headphones. However, it is optional to use stereo headphones
with a built-in microphone for the intercom function.
8
English
3. GETTING STARTED
3.1 Installing the Bluetooth Mic &
Intercom
2
Wear the armband on your arm.
3.1.1 Installing on the Armband
3
Adjust the direction of the microphone
to your mouth by rotating the Bluetooth
Microphone.
1
Attach the armband on the back of the
Bluetooth Mic along the guide rail.
9
3.1.2 Installing on the Collar Clip
1
10
Attach the collar clip on the back of the
Bluetooth Mic along the guide rail.
2
Attach the Bluetooth Mic on your collar by
the clip.
3
Adjust the direction of the microphone
to your mouth by rotating the Bluetooth
Microphone.
3.3 Powering On/Off
The Bluetooth Mic does not have internal
speakers. By connecting stereo headphones
that have a built-in microphone into the
earbud jack, you can make a phone call, have
an intercom conversation or listen to music.
To power on the Bluetooth Mic, slide the power
switch to on. The blue and red LEDs will turn
on. To power off, slide the power switch to off.
ON
OFF
3.4 Voice Prompt
x You can control all the functions of the
Bluetooth Mic by your headphones if it
has the controller for an Android phone.
x You can play/pause the music, or start/
end the intercom by your headphones
if it has the controller for an iPhone.
On the Bluetooth Mic, the voice prompt works
as an essential feedback from your operation.
Since the Bluetooth Mic does not have builtin speakers, you must use headphones to
hear the voice prompts. You can hear voice
messages and voice prompts when you
operate the Bluetooth Mic such as when
11
English
3.2 Connecting Your Headphones
putting the Bluetooth Mic into pairing mode or
entering the “Configuration menu”. It is strongly
recommended for you to use headphones to
proplerly set up the system.
3.5 Volume Adjustment
You can easily adjust the volume by tapping
the (+) Button or the (-) Button. You will hear
a beep when the volume reaches maximum
or minimum level. The volume is set and
maintained independently at different levels
for each audio source even when you turn off
and on the Bluetooth Mic. For example, once
you set the volume for a paired mobile phone,
it will not change even if you adjust the volume
when you hear Bluetooth MP3 music. So you
can always maintain the preferred optimum
volume level for each audio source.
12
3.6 Using Internal/External
Microphone
Users may use either the built-in microphone
of the Bluetooth Mic (internal microphone)
or the microphone of a connected pair of
headphones (external microphone). According
to the application, you may use either one by
using the switching operation. Press the (-)
Button for 3 seconds and then the mode will be
switched to the one for internal microphone or
external microphone. (factory default: internal
microphone)
3.8 Charging
The Bluetooth Mic operates in the following
order of priority:
The charging LED beside the charging port
turns red while charging and turns blue when
the Bluetooth Mic is fully charged. It takes
about 2.5 hours to be completely charged. You
can use the Bluetooth Mic while charging. It
is especially helpful when you use a cigarette
charger for a long road trip.
(highest) Mobile phone,
Intercom,
Music sharing by Bluetooth stereo music,
(lowest) Bluetooth stereo music
A lower priority function is always interrupted
by a higher priority function. For example,
stereo music is interrupted by an intercom call,
and an intercom conversation is interrupted by
an incoming mobile phone call.
13
English
3.7 Function Priority
3.9 Low Battery Warning
3.10.2 Voice Prompt Indicator
When the battery is low, the blinking blue LED
in stand-by mode turns to red and you will hear
mid-toned triple beeps and a voice prompt
saying “Low battery”.
When you power on the Bluetooth Mic, keep
pressing the Center Button and the (+) Button
simultaneously for several seconds until you
hear high toned triple beeps. Then you will
hear voice prompt indicating the battery level.
However, if you release the buttons as soon as
the Bluetooth Mic turns on, you will not hear
the voice prompt of battery level indicator.
3.10 Checking the Battery Level
You can check the battery level in two different
ways when the Bluetooth Mic is powering on.
3.10.1 LED Indicator
When the Bluetooth Mic is powering on, the
red LED flashes rapidly indicating the battery
level.
4 flashes = High, 70~100%
3 flashes = Medium, 30~70%
2 flashes = Low, 0~30%
14
English
3.11 Fault Reset
When the Bluetooth Mic is not working
properly or is in faulty status for any reason, you
may reset by pushing the pin-hole reset button
at the right side of the main unit. Insert a paper
clip into the reset pin-hole and press the reset
button for a second with light pressure. The
Bluetooth Mic will be switched off, and you
have to turn the system back on and try again.
However, this will not restore the Bluetooth Mic
to factory default setting.
15
4. CONFIGURATION SETTING
You can set the configuration of the Bluetooth
Mic by the voice menu instruction as below.
1. To enter into voice configuration menu, press
and hold the Center Button for 12 seconds
until the LED turns solid blue and you hear
high toned double beeps. You will also hear a
voice prompt saying “Configuration menu”.
2. Tap the (+) Button or (-) Button to navigate
between the menus. You will hear voice
prompts for each menu items as below.
3. You can enable the feature or execute the
command by tapping the Center Button.
4. If you want to exit the configuration
immediately, tap the (+) Button or (-) Button
until you hear a voice prompt saying “Exit
configuration”, then tap the Center Button.
16
The voice prompt for each menu item is as
below:
(1) Phone pairing
(2) Multipoint pairing
(3) Phone selective pairing
(4) Media selective pairing
(5) Speed dial
(6) Voice prompt
(7) Sidetone
(8) Noise Control
(9) Auto gain control
(10) Delete all pairings
(11) Factory reset
(12) Exit configuration
Phone pairing*
Phone selective pairing
Exit configuration**
Media selective pairing
Factory reset
Speed dial
Delete all pairings
Voice prompt
Auto gain control
Noise control
Sidetone
(*Default Setting)
(**Default Setting)
4.1 Mobile Phone Pairing
Voice Prompt
“Phone pairing”
Factory Default
N/A
To go into mobile phone pairing mode, tap
the (+) Button or the (-) Button until you hear a
voice prompt saying “Phone pairing”. Please
refer to section 5.1 for details on mobile phone
pairing. If you tap the (+) or (-) Button, you can
exit from the phone pairing mode.
4.2 Multipoint Pairing
Voice Prompt
“Multipoint pairing”
Factory Default
N/A
To go into multipoint pairing mode, tap the (+)
Button or the (-) Button until you hear a voice
prompt saying “Multipoint pairing”. Please
refer to section 5.2 for details on multipoint
pairing. If you tap the (+) or (-) Button, you can
exit from the multipoint pairing mode.
17
English
Multipoint pairing
4.3 Phone Selective Pairing
Voice Prompt
“Phone selective pairing”
Factory Default
N/A
To go into phone selective pairing mode,
tap the (+) Button or the (-) Button until you
hear a voice prompt saying “Phone selective
pairing”. Please refer to section 6.1 for more
details on phone selective pairing. If you tap
the (+) or (-) Button, you can exit from the
phone selective pairing mode.
4.4 Media Selective Pairing
Voice Prompt
“Media selective pairing”
Factory Default
N/A
To go into media selective pairing mode,
tap the (+) Button or the (-) Button until you
18
hear a voice prompt saying “Media selective
pairing”. Please refer to section 6.2 for more
details on media selective pairing. If you tap
the (+) or (-) Button, you can exit from the
media selective pairing mode.
4.5 Assigning Speed Dial
Voice Prompt
“Speed dial”
Factory Default
N/A
Execute
Tap the Center Button
1. To assign a phone number as a speed dial, tap
the (+) Button or the (-) Button until you hear
a voice prompt saying “Speed dial”.
2. Tap the Center Button, and you will hear voice
prompts saying “Speed dial one” and “Phone
connected”.
4. Call a phone number you want to assign
and you will hear a voice prompt saying
“Save speed dial (#)”. The phone number is
automatically assigned to the selected speed
dial number. Then the phone call will hang up
before being connected.
5. To exit the menu, tap the (+) Button or the
(-) Button until you hear a voice prompt
saying “Cancel”, and tap the Center Button
to confirm. You will then hear a voice prompt
saying “Cancel”. If any button is not pressed
within 1 minute, the Bluetooth Mic will exit
the configuration menu and go back to standby mode.
1. You can assign up to 3 phone numbers for
speed dial.
2. You can assign phone numbers for speed
dialing by using the Sena Device Manager
software. For more information, visit the Sena
Bluetooth web site at www.sena.com.
4.6 Enabling/Disabling Voice
Prompts
Voice Prompt
“Voice prompt”
Factory Default
N/A
Enable / Disable
Tap the Center Button
You can disable voice prompts by configuration
setting, but the following voice prompts are
always on.
- Voice prompts for configuration menu
- Voice prompts for battery level Indicator
19
English
3. Tap the (+) Button or the (-) Button to select
one of three speed dial numbers and you will
hear a voice prompt saying “Speed dial (#)”.
- Voice prompts for factory reset
- Voice prompts for speed dial
4.7 Enabling/Disabling Sidetone
4.8 Enabling/Disabling Advanced
Noise Control
Voice Prompt
“Noise control”
Voice Prompt
“Sidetone”
Factory Default
Enable
Factory Default
Disable
Enable / Disable
Tap the Center Button
Enable / Disable
Tap the Center Button
Sidetone is the sound of your own voice as
picked up by your microphone and reproduced
in your own ear. It helps you to naturally speak
at the correct level according to varying noise
conditions. If this feature is enabled, you can
hear what you are speaking during a recording,
an intercom conversation or a phone call.
20
When Advanced Noise Control is enabled, the
background noise is reduced during an intercom
conversation. When it is disabled, the background
noise is mixed with your voice during intercom.
If you use the Bluetooth Mic with the
Bluetooth Audio Pack for GoPro, you can
enable or disable this feature only during
Normal Voice Recording. This feature is
automatically disabled while in Ultra HD
(UHD) Voice Recording mode.
4.10 Delete All Bluetooth Pairing
Information
Voice Prompt
“Auto gain control”
Voice Prompt
Factory Default
Enable
Factory Default
N/A
Enable / Disable
Tap the Center Button
Enable / Disable
Tap the Center Button
You can use the auto gain control to keep the
volume of recording sounds constant regardless
of the loudness. Auto gain control activates when
the Bluetooth Mic connects to the Sena Bluetooth
Audio Pack or the Sena PRISM. It is useful when
you move a lot wearing the Bluetooth Mic from
the recording device. It is useful when you move
a lot while wearing the Bluetooth Mic and a
recording device.
English
4.9 Enabling/Disabling Auto Gain
Control
“Delete all pairings”
To delete all Bluetooth pairing information on the
Bluetooth Mic, tap the (+) Button or the (-) Button
until you hear a voice prompt saying “Delete all
pairings”. Tap the Center Button to confirm.
21
4.11 Reset to Factory Default Setting
4.12 Exit Voice Configuration Menu
Voice Prompt
“Exit configuration”
Voice Prompt
“Factory reset”
Factory Default
N/A
Factory Default
N/A
Enable / Disable
Tap the Center Button
Enable / Disable
Tap the Center Button
To restore factory default settings on the
Bluetooth Mic, tap the (+) Button or the (-)
Button until you hear a voice prompt saying
“Factory reset”. Tap the Center Button to
confirm. The Bluetooth Mic powers off with
a voice prompt saying “Headset reset,
goodbye” and powers on again.
22
To exit voice configuration menu and get back
to stand-by mode, tap the (+) Button or (-)
Button until you hear a voice prompt saying
“Exit configuration”. Tap the Center Button to
confirm.
Tap Center Button
Phone Pairing
None
Multipoint Pairing
None
Phone Selective Pairing
None
Media Selective Pairing
None
Speed Dial
Execute
Voice Prompt
Enable / disable
Sidetone
Enable / disable
Advanced Noise Control
Enable / disable
Auto Gain Control
Enable / disable
Delete All Pairings
Execute
Factory Reset
Execute
Exit Configuration
Execute
English
Press (+) Button or
(-) Button
Voice Configuration Menu & Button Operations
23
5. PAIRING THE BLUETOOTH MIC & INTERCOM WITH BLUETOOTH DEVICES
Before using the Bluetooth Mic, you need to
do the pairing operation. It can be paired with
Bluetooth mobile phones or Bluetooth stereo
devices such as MP3. This pairing operation is
only required once for each Bluetooth device.
The Bluetooth Mic will remain paired with the
devices and automatically connects to the
paired devices again when they are within
range.
2. By tapping the (+) Button, the red and blue
LED flash alternatively and you will hear a
voice prompt saying “Phone pairing”.
5.1 Mobile Phone Pairing
5. The mobile phone confirms that pairing has
completed and the Bluetooth Mic is ready to
use. You will hear a voice prompt saying “Your
headset is paired”.
1. To enter into the voice configuration
menu, press and hold the Center Button
for 12 seconds until the LED shows solid
blue and you hear a voice prompt saying
“Configuration menu”.
24
3. Search for Bluetooth device on your mobile
phone. Select the Sena Bluetooth Mic in the
list of the devices detected on the mobile
phone.
4. Enter 0000 for the PIN. Some mobile phones
may not ask for the PIN.
6. If the pairing process is not completed within
three minutes, the Bluetooth Mic will return to
stand-by mode.
Typical Bluetooth headsets can connect with
only one HFP (Hands-Free Profile) device,
but multipoint pairing allows the headset to
connect with two HFP devices at the same
time. So, when you already have a mobile
phone connected with the Bluetooth Mic, you
can also pair and connect a second mobile
phone or other HFP devices such as Bluetooth
adapter.
1. To enter into the voice configuration menu,
press and hold the Center Button for 12
seconds until the LED shows solid blue and
you hear voice prompt saying “Configuration
menu”.
2. Double tap the (+) Button then the blue LED
flashes rapidly and you will hear voice prompt
saying “Multipoint pairing”.
3. If you want to pair a second mobile phone,
search for the Bluetooth device on your
mobile phone, and select the Sena Bluetooth
Mic in the list of the devices detected on the
mobile phone.
4. Enter 0000 for the PIN. Some mobile phones
may not ask for the PIN.
5. The mobile phone confirms that pairing has
completed and the Bluetooth Mic is ready to
use. You will hear a voice prompt saying “Your
headset is paired”.
5.3 Bluetooth Stereo Device Pairing
If the Bluetooth stereo device is integrated
with the mobile phone such as smartphones,
you don’t need to pair the Bluetooth Mic with
it separately. When the Bluetooth Mic is paired
with the mobile phone, it is also paired as a
stereo music device.
25
English
5.2 Multipoint Pairing
If you have a stand alone Bluetooth stereo
device, follow the pairing procedure separately.
The procedure is the same as the procedure of
“5.1 Mobile Phone Pairing”.
1. If a Bluetooth connection between the
Bluetooth Mic and a mobile phone is
disconnected, press the Center Button for 3
seconds until you hear a high toned single
beep to recover the Bluetooth connection
immediately.
2. If a Bluetooth connection between the
Bluetooth Mic and a media player is
disconnected, press the Center Button
for 1 second to recover the Bluetooth
connection and play.
26
5.4 Pairing with the Bluetooth Pack
for GoPro® or PRISM
The Bluetooth Mic can be paired with the
Bluetooth Audio Pack for GoPro® or PRISM for
Bluetooth voice recording.
1. Turn on the Bluetooth Mic and the Bluetooth
Audio Pack or PRISM that you want to pair
with.
2. Press and hold the Center Button for 5 seconds
on the Bluetooth Mic, then the red LED flashes
rapidly and you will hear a mid-toned single
beep and the voice prompt saying “Intercom
pairing”.
3. Perform the operation required for pairing
on the Bluetooth Audio Pack or PRISM (refer
to the Users’ Guide). The Bluetooth Mic will
automatically perform pairing with Bluetooth
Audio Pack or PRISM while in pairing mode.
If you have a MP3 stereo music phone such
as a smartphone, sometimes you may need
to selectively use the Bluetooth Mic for
A2DP stereo music only or for mobile phone
handsfree only. This instruction is for advanced
users who want to pair the Bluetooth Mic to
their smartphones only with one selective
profile: A2DP stereo for music or HFP for phone
call.
If you have previously paired a mobile phone to
the Bluetooth Mic, you must clear the previous
pairing list on both devices; the mobile phone
and the Bluetooth Mic. To clear the pairing list
on the Bluetooth Mic, please do a factory reset
or follow the pairing list clearing procedure
described in this manual. To clear the pairing
list on the mobile phone, please refer to the
mobile phone manual. For most smartphones,
delete the Bluetooth Mic from the list of
Bluetooth devices in setting menu.
6.1 Phone Selective Pairing: HFP
for Phone Call Only
1. To enter into the voice configuration menu,
press and hold the Center Button for 12
seconds until you hear a voice prompt saying
“Configuration menu”.
2. Triple tap the (+) Button and you will hear
a voice prompt saying “Phone selective
pairing”.
3. Search for Bluetooth devices on your
smartphone. Select the Bluetooth Mic in the
list of devices detected on your phone.
27
English
6. PAIRING WITH SELECTIVE PROFILE: HFP OR A2DP STEREO
4. Enter 0000 for the PIN. Some smart phones
may not ask for PIN.
6.2 Media Selective Pairing: A2DP
Stereo Music Only
1. To enter into the voice configuration menu,
press and hold the Center Button for 12
seconds until you hear a voice prompt saying
“Configuration menu”.
2. Tap the (+) Button four times and you will
hear a voice prompt saying “Media selective
pairing”.
3. Search for Bluetooth devices on your
smartphone. Select the Bluetooth Mic in the
list of devices detected on your phone.
4. Enter 0000 for the PIN. Some smartphones
may not ask for PIN.
28
You can listen to stereo music from your
Bluetooth wireless audio device. The Bluetooth
audio device must be paired with the
Bluetooth Mic by following the “Bluetooth
Stereo Device Pairing” procedures described in
the 5.3 chapter. The Bluetooth Mic supports the
Audio/Video Remote Control Profile (AVRCP),
so if your Bluetooth audio device also supports
the AVRCP, you can use the Bluetooth Mic
to remotely control music playback. You not
only can adjust the volume but also use the
functions such as play, pause, next track and
previous track.
1. To adjust the volume, tap the (+) Button or the
(-) Button.
2. To play or pause music, press the Center
Button for 1 second until you hear a midtoned double beep.
3. To track forward or track back, press the (+)
Button or the (-) Button for 1 second until you
hear a mid-toned single beep.
You can stop music streaming while you are
listening to the music by pressing the (-) Button
for 4 seconds until you hear high toned double
beeps.
29
English
7. STEREO MUSIC
8. MOBILE PHONE CALL MAKING AND ANSWERING
8.1 Mobile Phone Call Making and
Answering
1. When you have an incoming call, tap the
Center Button to answer the call.
2. To end a call, press the Center Button for 2
seconds until you hear a mid-toned single
beep, or wait for the called person to end the
call.
3. To reject a call, press the Center Button for
2 seconds until you hear a beep while the
phone is ringing.
4. There are several ways to make a phone call:
x Enter numbers on your mobile phone
keypad and make a call. Then the call
is automatically transferred to the
Bluetooth Mic.
30
x In stand-by mode, press the Center
Button for 3 seconds to activate the
voice dialing of your mobile phone.
You will hear a high toned single beep.
Your mobile phone has to support voice
dialing. Refer to your mobile phone
manual for further instruction.
If you are using a multipoint mobile phone
connection and you have an incoming call
from the second phone during the call of
the first phone, then you may still receive
the call from second phone. In this case, the
call from the first phone is in waiting mode.
If you end a call, then it will automatically
guide you to the first phone call.
You can quickly make a phone call by using the
voice speed dial menu.
1. To enter into the voice speed dial menu, press
and hold the (+) Button for 3 seconds and you
will hear a mid-toned single beep and a voice
prompt saying “Speed dial”.
2. Tap the (+) Button or the (-) Button to navigate
between the menus. You will hear voice
prompts for each menu items.
3. Tap the Center Button to select a voice menu
among the followings:
(1) Last number redial
(2) Speed dial 1
(3) Speed dial 2
(4) Speed dial 3
(5) Cancel
4. After selecting the last number redial menu,
you will hear a voice prompt saying “Last
number redial”. Then, to redial the last phone
call number, tap the Center Button.
5. To call one of the speed dials, tap the (+)
Button or the (-) Button to navigate between
the menus until you hear a voice prompt
saying “Speed dial (#)”. Then, tap the Center
Button.
6. If you want to exit the speed dial immediately,
tap the (+) Button or the (-) Button until you
hear a voice prompt saying “Cancel”, and tap
the Center Button. If any button is not pressed
within 15 seconds, the Bluetooth Mic will exit
the voice speed dial menu and goes back to
stand-by mode.
7. To cancel the voice dialing or redialing last
number command, tap the Center Button
while it is in progress.
31
English
8.2 Speed Dialing
Make sure that you should connect the
mobile phone and the Bluetooth Mic in
order to use the speed dial function.
Answer
End
Reject
Call
Speed Dial
Voice Command
Tap the Center Button
Press the Center Button for 2
seconds
Press the Center Button for 2
seconds
Use phone keypad
Press the (+) Button for 3
seconds
Press the Center Button for 3
seconds
Mobile Phone Call Button Operations
32
If you have a second mobile phone connected
with the Bluetooth Mic by multipoint connection,
you can answer the incoming call to the second
mobile phone by tapping the Center Button while
you are on the line of the first mobile phone. In
this case, the first call is on call waiting.
9.1 Pairing with Other Bluetooth
Mic & Intercom for Intercom
Conversation
The Bluetooth Mic can be paired with up
to three other Bluetooth Mics for Bluetooth
intercom conversation.
the LEDs of both Bluetooth Mic turn to blue
and intercom connection is automatically
established. The two Bluetooth Mics A and
B are paired with each other for intercom
conversation. If the pairing process is not
completed within one minute, the Bluetooth
Mic will return to stand-by mode.
A
1. Turn on the two Bluetooth Mics (A and B) that
you would like to pair with each other.
2. Press and hold the Center Button for 5
seconds, then the red LED flashes rapidly and
you will hear a mid-toned single beep and a
voice prompt saying “Intercom pairing”.
3. Simply tap the Center Button of any one of
the two Bluetooth Mics A or B (It doesn’t
matter that you choose A or B.) and wait until
B
D
C
Pairing A & B
33
English
9. INTERCOM
4. You can make other pairings between the
Bluetooth Mic A and C, and between the
Bluetooth Mic A and D by following the same
procedure as above.
A
B
D
C
Pairing A & C
34
A
B
D
C
Pairing A & D
5. The intercom pairing queue is ‘Last-Come, FirstServed’. If a Bluetooth Mic has multiple paired
Bluetooth Mics for intercom conversations,
the last paired Bluetooth Mic is set as first
intercom friend. The previous intercom friend
becomes second intercom friend, and third
intercom friend.
For example, after the pairing procedures
listed above, Bluetooth Mic D is the first
intercom friend of Bluetooth Mic A.
Bluetooth Mic C is the second intercom
friend of Bluetooth Mic A, and Bluetooth
Mic B is the third intercom friend of
Bluetooth Mic A.
The Bluetooth Mic can be paired with all
other Sena headset models such as the
SMH10, SPH10 and the SMH5 for intercom
conversation. Please follow the same procedure
as above to pair with these headset models.
The SMH5 cannot participate in threeway or four-way conference intercom with
the Bluetooth Mic. The SMH5 has a limited
capability of having two-way intercom
with each other or with other Sena headset
models.
9.3 Two-way Intercom
English
9.2 Pairing with Other Sena
Headset Models for Intercom
Conversation
9.3.1 Start and End Two-way Intercom
1. You can start a one-on-one intercom
conversation with any intercom friend by
tapping the Center Button: Single tapping to
intercom with the first intercom friend, double
tapping with the second intercom friend, or
triple tapping with the third intercom friend.
2. To terminate a one-on-one intercom
conversation, single tap the Center Button.
This will end the intercom conversation.
1st intercom
friend
Start
intercom
End
intercom
Single tap
2nd intercom 3rd intercom
friend
friend
Double tap
Triple tap
Single tap
Start & End Two-way Intercom
35
9.3.2 Intercom and Mobile Phone Call
1. When you have an incoming mobile phone
call during an intercom conversation, you will
hear a ring tone. You can choose whether to
1) answer the mobile phone call and stop the
intercom conversation, or 2) reject the phone
call and stay on the intercom conversation or
3) Ignore the incoming phone call and allow
the caller to go to voice mail.
a. To answer the phone call and stop the
intercom conversation, tap the Center
Button. When you hang up the phone
call, the intercom will automatically be
recovered.
b. To reject the phone call and stay on the
intercom conversation, press the Center
button for 2 seconds until you hear a beep.
36
c. To ignore an incoming phone call, just wait
until the caller goes to voice mail. You will
maintain the intercom call while the caller is
leaving a voice message.
This prevents a user from being dropped
out of an intercom conversation by an
incoming mobile call.
2. When you have an incoming intercom call
during a mobile phone call, you will hear 4
high toned beeps, alerting you that there is
an incoming intercom call. You will also hear a
voice prompt saying “Intercom requested”.
In this case, the intercom call does not
override the mobile phone call because
intercom has lower priority than mobile call.
You have to hang up the mobile phone call to
make or receive an intercom call.
First Friend
(B)
(A)
ng
iri
Pa
You (A) can have a three-way conference
intercom with two other Bluetooth Mic
friends (B & C) by establishing two intercom
connections at the same time. While a threeway conference intercom is in progress, mobile
phone connection of all three participants
would be temporarily disconnected, but as
soon as the conference intercom terminates
or one of the participants leaves the intercom,
all mobile phones would be automatically
reconnected. During the conference intercom,
if you have an incoming mobile phone
call, terminate the conference intercom to
automatically reconnect the mobile phone and
receive the call.
Pa
iri
ng
9.4.1 Start Three-way Intercom
1. You (A) need to be paired with two other
friends (B & C) for three-way conference
intercom.
English
9.4 Three-way Conference Intercom
Second Friend
(C)
2. Start an intercom conversation with one
of the two friends in your intercom group.
For example, you (A) may start an intercom
conversation with the intercom friend (B). Or
intercom friend (B) may start an intercom call
with you (A).
37
4. Now you (A) and two Bluetooth Mic intercom
friends (B & C) are having a three-way conference
intercom.
(A)
First Friend
(B)
(A)
Second Friend
(C)
3. The second intercom friend (C) may join the
intercom by making an intercom call to you
(A).
First Friend
(B)
Second Friend
(C)
9.4.2 End Three-way Intercom
(A)
First Friend
(B)
38
Second Friend
(C)
When you are a member of an active threeway conference intercom, you can completely
terminate the conference intercom or just
disconnect an intercom connection with one of
your active intercom friends.
2. Tap or double tap the Center Button to
disconnect intercom connection with one
of the two intercom friends accordingly. For
example, by single tapping the Center Button,
you can terminate the intercom connection
with the first intercom friend (B). However,
you still have the intercom connection with
your second intercom friend (C). To disconnect
from intercom friend (C), double tap the
Center Button. Now both intercom friends are
disconnected.
Center Button
Result
Press for 1”
Disconnect (B) & (C)
Single tap
Disconnect (B)
Double tap
Disconnect (C)
End Three-way Intercom
9.4.3 Three-way Conference Phone Call
with Intercom Participant
You can have a three-way conference phone
call by adding an intercom friend to the mobile
phone conversation. While having a mobile
phone call, make an intercom call to one of
your intercom friends (B, C or D) by tapping
the Center Button once, twice or three times
to form a three-way conference call with the
person on the mobile phone line. To disconnect
the intercom first and go back to your private
mobile phone call, terminate the intercom
39
English
1. Press the Center Button for 1 second until
you hear a beep to terminate three-way
conference intercom completely. It terminates
both intercom connections with (B) and (C).
by tapping the Center Button once. To end
the mobile phone call first and maintain the
intercom conversation, press the Center Button
for 2 seconds, or wait for the person on the
mobile phone line to end the call.
Start
End intercom
first
Tap the Center Button while
having a mobile phone call
Tap the Center Button
Press the Center Button for 2“
End phone call or
Wait for the called person to end
first
the call
Start & End Three-way Conference Phone Call
40
9.5 Four-way Conference Intercom
9.5.1 Start Four-way Intercom
You can have four-way conference intercom
with three other Bluetooth Mic users by adding
one more intercom participant to the threeway intercom. While you are having threeway intercom as above in section 9.4.1, a new
participant (D), who is an intercom friend
of your intercom friend (C), may join the
conference intercom by making an intercom
call to your intercom friend (C). Please note
that in this case, the new participant (D) is an
intercom friend of (C), not of you (A).
First Friend
(B)
New
Participant
(D)
= Intercom
Friend of (C)
Second Friend
(C)
9.5.2 End Four-way Intercom
As same in the case of three-way intercom,
you can completely get out of the four-way
conference intercom or just disconnect a single
intercom connection.
1. Press the Center Button for 1 second until you
hear a beep to terminate four-way conference
intercom. It terminates the intercom
connections between you (A), and your
intercom friends (B), (C) and (D).
Center Button
Result
Press for 1”
Disconnect (B), (C) & (D)
Single tap
Disconnect (B)
Double tap
Disconnect (C) & (D)
End Three-way Intercom
41
English
You
(A)
2. Tap or double tap the Center Button to
disconnect the intercom connection with
one of the two intercom friends accordingly.
However, when you disconnect the second
friend (C) by double tapping the Center
Button, you will be disconnected with the
third participant (D) as well. This is because
the third participant (D) is connected with you
via the second friend (C).
9.6 Intercom Failure
When you try to start an intercom conversation
with an intercom friend who is already having
a conference intercom with other riders or a
mobile phone call, you will hear a low toned
double beep signifying an intercom busy
signal. In this case, you have to try again later.
9.7 Intercom Reconnection
If your intercom friend goes out of range while
having an intercom conversation, you may hear
static noise and eventually the intercom will
be disconnected. In this case, the Bluetooth
Mic automatically tries to reconnect the
intercom every 8 seconds and you will hear
high tone double beeps until the intercom
is reestablished. If you don’t want to make a
reconnection, tap the Center Button to stop the
attempt.
42
You can have an intercom conversation
with non-Sena Bluetooth headsets using
the Universal Intercom function. Non-Sena
Bluetooth headsets can be connected to the
Bluetooth Mic if they support the Bluetooth
Hands-Free Profile (HFP). The working distance
may differ depending on the performance
of Bluetooth headset that it is connected to.
In general, it is shorter than normal intercom
distance since it uses the Bluetooth Hands-Free
Profile.
10.1 Universal Intercom Pairing
The Bluetooth Mic can be paired with non-Sena
Bluetooth headsets for Bluetooth intercom
conversation.
English
10. UNIVERSAL INTERCOM
1. Turn on the Bluetooth Mic and a non-Sena
Bluetooth headset which you want to pair
with.
2. Press and hold the Center Button on the
Bluetooth Mic for 8 seconds until the blue LED
flashes rapidly. You will hear a voice prompt
saying “Universal intercom pairing”.
3. Perform the operation required for handsfree
pairing on the non-Sena Bluetooth headset
(refer to the users’ manual of the headsets
you want to use). The Bluetooth Mic will
automatically perform pairing with non-Sena
Bluetooth headsets while in pairing mode.
43
10.2 Two-way Universal Intercom
10.3 Three-way Universal Intercom
You can initiate the Universal Intercom
connection with non-Sena Bluetooth headsets
using the same intercom connection method
as you would between other Sena headsets.
You may single tap the Center Button to
begin an intercom conversation with the first
intercom friend, double tap with the second
intercom friend, and triple tap with the third
intercom friend.
You may make a three-way Universal Intercom
connection with two Bluetooth Mic and one
non-Sena Bluetooth headset. If the intercom
connection is made, all headsets connected
cannot use the mobile phone call function
since the connection between the headset
and the phone is disconnected temporarily. If
you disconnect the intercom call, the mobile
phone connection is made again automatically
so that you can use a mobile phone call
function. During the intercom call, you cannot
pick up the incoming phone call since it is
disconnected, however, you can pick it up if
you disconnect the intercom call.
Non-Sena Bluetooth headsets may initiate the
Universal Intercom connection by activating
the voice dialing or using the redialing
operation. You may also disconnect the existing
connection by ending a call operation function
(refer to the users’ manual of the headsets for
voice dialing, redialing, and ending a call).
44
1. You (A) need to be paired with non-Sena
Bluetooth headset (B) and another Bluetooth
Mic (C) for the three-way conference intercom.
(C)
Pa
iri
ng
2. Start an intercom conversation with non-Sena
Bluetooth headset (B) in your intercom group.
For example, you (A) may start an intercom
conversation with non-Sena Bluetooth
headset (B). The non-Sena Bluetooth headset
(B) may also start an intercom call with you (A).
English
ng
iri
Pa
(B)
(A)
(A)
(C)
(B)
3. The other Bluetooth Mic (C) may join the
intercom by making an intercom call to you
(A).
(A)
(B)
(C)
45
4. Now you (A), non-Sena Bluetooth headset (B),
and the other Bluetooth Mic (C) are having a
three-way conference intercom.
(A)
(B)
(C)
5. You may disconnect the three-way Universal
Intercom using the same way as you do in
normal three-way intercom. Please refer to
section, 9.4.2 “End Three-way Intercom”.
46
10.4 Four-way Universal Intercom
You may make a four-way Universal Intercom
connection with a couple of different
configurations, 1) three Bluetooth Mic and
one non-Sena Bluetooth headset or 2) two
Bluetooth Mic and two non-Sena Bluetooth
headsets.
You may have a couple of other four-way
Universal Intercom configurations, 1) your
Bluetooh Mic (A), a non-Sena Bluetooth headset
(B), another Bluetooth Mic (C), and a non-Sena
Bluetooth headset (D), 2) your Bluetooth Mic
(A), a non-Sena Bluetooth headset (B), and two
other Bluetooth Mic (C and D). You may make
the four-way Universal Intercom call the same
way as a normal four-way intercom call.
Two Bluetooth Mic (A and C) and two non-Sena
Bluetooth headsets (B and D).
2. The other Bluetooth Mic (C) may join the
intercom by making an intercom call to you
(A).
1. You (A) may start an intercom conversation
with the non-Sena Bluetooth headset (B).
(A)
(A)
(C)
(B)
(B)
(C)
(D)
(D)
47
English
10.4.1 Four-way Universal Intercom Case 1
3. The non-Sena Bluetooth headset (D) may
join the conference intercom by making an
intercom call to the Bluetooth Mic (C).
(A)
4. Now two Bluetooth Mic (A & C) and two
non-Sena Bluetooth headsets (B & D) are
connected with the four-way Universal
Intercom.
(C)
(A)
(B)
(C)
(D)
(B)
(D)
You may disconnect a four-way Universal
Intercom using the same way as you do in
a normal four-way intercom. Please refer to
section, 9.5.2 “End Four-way Intercom”.
48
Three Bluetooth Mic (A, C and D) and one nonSena Bluetooth headset (B). The procedure is
the same as the case 1 described in section
10.4.1.
(A)
(B)
(C)
(D)
The Universal Intercom affects both the
phone call connection on a non-Sena
and the multipoint connection on a Sena
headset.
x If the non-Sena headset does not support
a multipoint connection then a phone
call connection will be unavailable
while using the Universal Intercom.
x If the non-Sena headset (that has been
paired to the Sena headset) is powered
on and is automatically connected, then
the multipoint connection of the Sena
headset will be deactivated. Therefore,
the multipoint paired device such as a
GPS will not be available for use with the
Sena headset while the non-Sena headset
is powered on, and turning it off will not
automatically restore the multipoint
connection. To restore the multipoint
connection on a Sena headset, you
should turn off the non-Sena headset first,
then try to connect the multipoint paired
device manually from the device screen
or simply reboot the multipoint paired
device so that it automatically connects
to the Sena headset.
49
English
10.4.2 Four-way Universal Intercom Case 2
11. MUSIC SHARING
You can start sharing music with an intercom
friend using Bluetooth stereo music during
a two-way intercom conversation. When you
terminate music sharing, you can go back
to the intercom conversation. To start or
terminate sharing music, press and hold the
Center Button for 1 second during an intercom
conversation until you hear a double beep and
you and your intercom friend will listen to or
terminate sharing music. To track forward or
track back, press the (+) Button or (-) Butt on
for 1 second until you hear a mid-toned single
beep.
50
1. Both you and your intercom friend can
remotely control music playback during
music sharing such as track forward and
track back.
2. When you have an incoming call or make
a phone call during music sharing, the
function will be paused.
3. In order to share music, make sure that
you update both Bluetooth Mics with
the firmware that has the music sharing
feature, and enable the EDR setting in
the Sena Device Manager.
English
12. FIRMWARE UPGRADE
The Bluetooth Mic supports firmware upgrade
function. Please visit Sena Bluetooth web site
at www.sena.com to check the latest software
downloads.
51
13. SENA BLUETOOTH CONNECTION CASE STUDIES
Case 1
Bluetooth Pairing Procedure
1 Intercom Pairing
2 Intercom Pairing
or
PRISM
GoPro® Pack
2
1
Intercom
Pairing
52
Intercom
Pairing
Usage
x PRISM or Bluetooth Audio Pack: taking
pictures, video recording with remote
audio
x Intercom
Bluetooth Pairing Procedure
1 Intercom Pairing
2 Intercom Pairing
3 Mobile Phone Pairing
or
PRISM
English
Case 2
GoPro® Pack
2
Usage
x PRISM or Bluetooth Audio Pack: taking
pictures, video recording with remote
audio
x Mobile phone: phone call, listening to
music
x Intercom
Intercom
Pairing
1
3
Intercom
Pairing
Mobile
Phone
Pairing
Mobile
Phone
53
14. OPERATION QUICK REFERENCE
Type
Description
Power-on
Power-off
Basic
Function Volume
adjustment
Button
Mobile Speed dial
Phone
Reject
incoming
call
54
LED
Beep
Ascending
beeps
Solid blue
Power Switch -
Descending
Solid red
beeps
(+) Button or
(-) Button
Tapping
-
-
3 sec
-
-
Center Button Tapping
-
-
(+) Button
3 sec
-
Mid-toned
single beep
Center Button 2 sec
-
-
Internal mic
(-) Button
/External mic
Answer
phone call
Duration
Power Switch -
Type
Description
Intercom
pairing
Universal
intercom
Intercom pairing
Start/end
intercom
conversation
End
conference
intercom
Play/pause
Bluetooth
music
Music
Track
forward/
back
Button
Duration
Center Button 5 sec
LED
Red
flashing
Beep
Mid-toned
single beep
Center Button of any one of the two Bluetooth Mics
Center Button 8 sec
Blue
flashing
-
Center Button Tapping
-
-
Center Button 1 sec
Blue
flashing
Mid-tone
single beep
Center Button 1 sec
-
Mid-tone
double beep
(+) Button or
(-) Button
-
-
1 sec
FCC Compliance Statement
This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested and found
to comply with the limits for a Class B digital
device pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment on and off, the user
is encouraged to try to correct the interference
by one or more of the following measures:
x Reorient or relocate the receiving antennae
x Increase the separation between the
equipment and the receiver
x Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
x Consult the dealer or an experienced radio/
TV technician for help.
55
English
CERTIFICATION AND SAFETY
APPROVALS
FCC RF Exposure Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. End users must follow the
specific operating instructions for satisfying RF
exposure compliance. The antenna used for this
transmitter must not transmit simultaneously
with any other antenna or transmitter, except in
accordance with FCC multi-transmitter product
procedures.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party
responsible for compliance could void user’s
authority to operate the equipment.
56
CE Declaration of Conformity
This product is CE marked according to the
provisions of the R&TTE Directive (99/5/EC).
Hereby, Sena declares that this product is in
compliance with the essential requirements
and other relevant provisions of Directive
1999/5/EC. For further information, please
consult www.sena.com. Please note that
this product uses radio frequency bands not
harmonized within EU. Within the EU this
product is intended to be used in Austria,
Belgium, Denmark, Finland, France, Germany,
Greece, Ireland, Italy, Luxembourg, The
Netherlands, Portugal, Spain, Sweden, United
Kingdom and within EFTA in Iceland, Norway
and Switzerland.
Bluetooth License
The Bluetooth® word mark and logos are
owned by the Bluetooth SIG, Inc. and any use
of such marks by Sena is under license. Other
trademarks and trade names are those of their
respective owners.
The product is compliant with and adopts
the Bluetooth® Specification 3.0 and has
successfully passed all interoperability tests that
are specified in the Bluetooth® specification.
However, interoperability between the device
and other Bluetooth®-enabled products is not
guaranteed.
57
English
Industry Canada Statement
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
WEEE (Waste Electrical and Electronic
Equipment)
The crossed-out wheel bin
symbol on the product,
literature, or packaging reminds
you that all electrical and
electronic products, batteries,
and accumulators must be taken
to separate collection at the end
of their working life. This requirement applies
to the European Union and other locations
where separate collection systems are
available. To prevent possible harm to the
environment or human health from
uncontrolled waste disposal, please do not
dispose of these products as unsorted
municipal waste, but hand it in at an official
collection point for recycling.
58
SAFETY INFORMATION
Please ensure that the product is properly used
by observing the warnings and cautions below
to prevent any risk and/or damage to property.
Product Storage and Management
x Keep the product free of dust. It may
damage mechanical and electronic parts of
the product.
x Do not store the product in high
temperatures as this may reduce the life
span of electronic devices, damage the
battery, and/or melt plastic parts of the
product.
x Condensation may form in and on the
product when you expose your product to
sudden changes in temperature or when
you use your product in a hot place, such as:
(1) When you take your product outside
from an air-conditioned room
x
x
x
x Do not disassemble, repair or modify the
English
x
(2) When you bring your product from the
cold place to a warm place
(3) When you use your product in a hot,
humid place
(4) When you use your product after it
rains
To prevent condensation from forming, put
your product inside a plastic bag and tightly
seal it. Remove your product from the plastic
bag after the temperature inside the bag is
similar to the external temperature.
Do not clean the product with cleaning
solvents, toxic chemicals, or strong
detergents as this may damage the product.
Do not paint the product. Paint may obstruct
moving parts or interfere with the normal
operation of the product.
Do not drop or otherwise shock the product.
It may damage the product or its internal
electronic circuits.
product as this may damage the product
and invalidate the product warranty.
x Do not wrap cables around the product
while carrying it.
x Do not store the product in humid
environments, especially for long time
storage.
Product Use
x Use of the product at a high volume for
a long period of time may damage your
eardrums or hearing ability. Keep the volume
at a modest level to prevent damage.
x Do not cause impact to the product or touch
it with sharp tools as this may damage the
product.
x Do not use the product in high-temperatures
or apply heat to the product as this may
cause damage, explosion, or fire.
59
x Keep product away from pets or small
x
x
x
x
children. They may damage the product.
In any place where wireless communication
is prohibited, such as hospitals or
airplanes, turn off the power and refrain
from using the product. In a place where
wireless communication is prohibited,
electromagnetic waves may cause hazards
or accidents.
Do not use the product near hazardous
explosives. When it is near any explosion
hazards, turn off the power and heed any
regulations, instructions, and signs in the
area.
Do not put the product where it may hamper
the user's vision or manipulate it while using
it. This may cause traffic accidents.
When you use your product near the ocean
or in other sandy place, do not allow sand to
60
x
x
x
x
enter the product. Sand may cause severe
damage to your product and can be difficult
to repair.
Remove the product from your back pocket
before sitting down.
If the product is damaged, stop using
it immediately. It may cause damage,
explosion, or fire.
While using the product, you may sometimes
experience a mild sting in your ears due to
static electricity accumulated in your body.
This is not a malfunction of the product. You
can reduce the static electricity by wearing
clothes made from natural materials.
Be careful when using the product in wet
environments. If the product gets wet, dry
it thoroughly before using it any further.
Do not attempt to dry the product with an
external heat source, such as a hair dryer.
Battery
This product has an irreplaceable rechargeable
battery inside. Therefore, when using the
product, make sure to adhere to the following:
x Never separate the battery from the product
as this may damage the product.
x The battery performance may be reduced
over time with usage.
x Make sure you turn off the product when
it is not in use. The battery discharges even
when your product is in standby mode.
x Make sure you charge the battery pack
enough before using your product.
x When recharging the battery, make sure
to use an approved charger provided by
the manufacturer. Use of a non-approved
charger may cause fire, explosion, leakage,
and other hazards may also reduce the life
time or performance of the battery.
x Any 3rd party USB charger can be used with
Sena products if the charger is approved
by either the FCC, CE, IC or other locally
approved agencies that Sena accepts.
x Store the battery at temperatures of
15°C~25°C (59°F~77°F). Higher or lower
temperatures may reduce the capacity and
life of the battery, or may cause temporary
non-operation. Do not use the product
in sub-zero temperature, because it may
cause serious reduction of the battery’s
performance.
x If you apply heat to the battery or throw it
into fire, it may explode.
61
English
The manufacturer takes no responsibility
for any damage to the product that may
have resulted from the product coming into
contact with liquid.
x Do not use the product with a damaged
battery. It may explode and/or cause
accidents.
x Never use a damaged charger. It may
explode and/or cause accidents.
x Battery life may vary depending on
conditions, environmental factors, functions
of the product in use, and devices used with
it.
PRODUCT WARRANTY AND
DISCLAIMER
Limited Warranty
Limited Warranty
Sena Technologies, Inc. (“Sena”) guarantees
the product quality based on the technical
specification stated in the product manual, and
data regarding product warranty. Here, product
warranty extends to the product only. Sena will
not be liable for any loss, damage of human life,
or loss of property which may result from using
the product beyond defective parts or flaws
that occur due to problems in manufacture.
Warranty Period
Sena guarantees free-of-charge replacements
of defective parts of the product or flaws
that may have occurred due to problems in
62
Termination
Quality warranty of the product becomes
effective on the date of initial purchase. In
addition, the quality warranty of the product
expires when the warranty period expires.
However, in the following cases, the warranty
will be terminated prematurely.
x In the event the product has been sold or
transferred to a third party.
x In the event the manufacturer’s name, serial
number, product label, or other markings
have been modified or removed.
x In the event any unauthorized person has
tried to disassemble, repair, or modify the
product.
Notice and Waiver
By buying and using this product, you
relinquish considerable legal rights including
any claim for compensation for damages.
Therefore, be certain to read and understand
the following terms and conditions before
using the product. Use of this product will
constitute consent to this agreement, and
forfeiture of rights to all claims. If you do not
consent to all the terms and conditions of this
agreement, return the product for a refund.
(Refer to the section “Return for Full Refund”.)
1. You agree that you, your descendants, legal
proxies, successors, or transferees will not
raise permanent volitional request for any
suit, claim, implementation, redemption or
similar action from Sena with regard to any
occasion such as difficulty, pain, suffering,
inconvenience, loss, injury, or death which
63
English
manufacture for a period of 2 years from the
date of initial purchase.
2.
3.
4.
5.
may occur to you or a third party during the
use of this product.
You must completely understand and
accept all risks (including those occurring
due to any careless behavior of yours or
others) which may occur during the use of
this product.
You are responsible for ensuring that
your medical condition permits usage of
the product and that you are in sufficient
physical condition for using any device
which can be used with it. In addition, you
must ensure that the product does not limit
your abilities and that you are able to use it
safely.
You must be an adult who can take
responsibilities for using the product.
You must read and understand the following
warnings and alerts:
64
x Sena; together with employees,
managers, partners, subsidiaries,
representatives, agents, supporting
firms and suppliers, sole sellers of Sena
(collectively referred to as “the company”)
recommend that, before using the
product and similar devices of any
brands including its derivative models,
you collect any relevant information in
advance and be entirely prepared in
terms of weather, traffic situation, and
road conditions.
x When you use the product while you
operating any vehicle or equipment
such as motorcycles, scooters, mopeds,
ATVs, or quad-bikes (hereinafter called
as “transportation means”), you must
take complete caution regardless of the
location of such operation.
cause such risks as fracture, serious
disability, or death.
x Risk factors, which may occur when
you use the product, may be due to
errors of the manufacturer, its agents, or
third parties which are involved in the
manufacturing.
x Risk factors, which may occur
when you use the product, may be
unforeseeable. Therefore, you must take
full responsibility for any damage or
loss caused by all risk factors which may
occur when using the product.
x When you use the product, use good
judgment; never use it under the
influence of alcohol.
6. You must read and completely understand
all terms and conditions of legal rights and
warnings that are involved in using the
product. In addition, usage of the product
constitutes acceptance of all terms and
conditions regarding waiver of rights.
Warranty Exclusions
Reasons for Limited Liabilities
If you do not return the product after
purchasing it, you relinquish all rights
to liabilities, loss, claims, and claims for
reimbursement of expenses (including
attorney’s fees). Therefore, Sena will not be
liable for physical injury, death, or any loss or
damage of transportation means, possessions,
or assets which belong to you or third parties
that may have occurred while you use the
product. Further, Sena will not be liable for
65
English
x Use of the product on the road may
any substantial damage not related to the,
condition, environment, or malfunction of the
product. All risks related with the operation
of the product depend entirely on the user
regardless of its use by the initial purchaser of a
third party.
Use of this product may violate local or national
laws. In addition, be aware once again that
correct and safe use of the product is entirely
your responsibility.
Limitation of Liability
TO THE FULL EXTENT ALLOWED BY LAW, SENA
EXCLUDES FOR ITSELF AND ITS SUPPLIERS
ANY LIABILITY, WHETHER BASED IN CONTRACT
OR TORT (INCLUDING NEGLIGENCE), FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY
KIND, OR FOR LOSS OF REVENUE OR PROFITS,
LOSS OF BUSINESS, LOSS OF INFORMATION
66
OR DATA, OR OTHER FINANCIAL LOSS ARISING
OUT OF OR IN CONNECTION WITH THE
SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION
OF ITS PRODUCTS, EVEN IF SENA OR ITS
AUTHORIZED RESELLER HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES, AND
LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT,
OR REFUND OF THE PURCHASE PRICE PAID, AT
SENA’S OPTION. THIS DISCLAIMER OF LIABILITY
FOR DAMAGES WILL NOT BE AFFECTED IF ANY
REMEDY PROVIDED HEREIN SHALL FAIL OF ITS
ESSENTIAL PURPOSE. IN ANY CASE, THE TOTAL
COMPENSATION LIABILITIES OF SENA OR ITS
SALES AGENTS SHALL NOT EXCEED THE PRICE
PAID FOR THE PRODUCT BY THE PURCHASER.
x In the event the product is damaged
because the user has disassembled, repaired,
or modified it in such way as is not explained
in the product manual.
x In the event the product is damaged by a
third party.
x In the event the product is damaged due to
Acts of God (including fire, flood, earthquake,
storm, hurricane or other natural disaster).
x In the event the surface of the product is
damaged by use.
67
English
Liabilities Disclaimer
In addition to damages which may occur due
to the use of the product, Sena will not be
liable for damages of the product which occur
due to the following events.
x In the event the product is misused or
used for purposes other than its intended
purposes.
x In the event the product is damaged
because the user does not follow the content
of the product manual.
x In the event the product is damaged
because it has been left unattended or has
undergone any other accident.
x In the event the product is damaged
because the user has used any parts or
software which are not provided by the
manufacturer.
Warranty Service
To obtain product warranty service, send the
defective product, at your expense, to the
manufacturer or the seller along with proof of
purchase (a receipt that shows the purchase
date, a product registration certificate of the
Website, and other relevant information). Take
necessary measures to protect the product. In
order to get a refund or replacement, you must
include the whole package as it was purchased.
Free-of-charge Service
Sena will provide free-of-charge repair or
replacement service for the product when
product defects occur within the scope of the
product warranty during the warranty period.
68
Return for Full Refund
Should you not agree to the terms and
conditions explained above, you may return
the product for a full refund. To get a refund,
within 14 days from the purchase date you
must return the product to the seller in such a
condition as it was purchased.
Unless you return the product within 14 days
from the purchase date, you will have read
and agreed to all the terms and conditions
explained above, and Sena will not be liable
for any claim for damages related with the
product.
1.0.3
www.sena.com
User's Guide for Firmware v1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising