Hisense | RR130DAGS | User manual | Hisense RR130DAGS User Manual

Hisense RR130DAGS User Manual
Ice Cube Tray
Freezer Compartment
Drip Tray
Removable shelve
Glass panel
7 Crisper
8 Levelling Legs
9 Bottle Racks
10 Temperature Control Knob
11 Recessed Handle
12 Light
NOTE: This figure is only a sketch of the refrigerator, the actual
product may differ from it.
Keep ventilation openings, in the applianceenclosure or in the built-in
structure, clear of obstruction.
Do not use mechanical devices or other means toaccelerate the
defrosting process.
Do not use electrical appliances inside the food storage compartments
of the appliance.
Well Ventilating
There is need of good ventilation around the refrigerator for easy dissipation of heat, high
efficiency of refrigeration and low power consumption.
For this purpose, sufficient clear space should be needed around the refrigerator, its back
is at least 100mm away from the wall, its sides at least have a space of 200mm separately
and the height from over its top is not less than 300mm.
A clear space should be left to open its doors to 160 .
Power Supply
The refrigerator is only applied with power supply of single phase alternating current
(See the rating label) .
If fluctuation of voltage in the district user is of so large that the voltage exceeds the scope,
for safety sake, be sure to apply A.C. automatic voltage regulator to the refrigerator.
The refrigerator must employ a special power socket instead of common one other electric
appliances. Its plug must match the socket with ground wire.
Power Line Cord
The cord should be neither lengthened nor folded into coil during operation. Moreover,
it is forbidden that cord is kept close onto the compressor at the back of the refrigerator,
the surface temperature of which is quite high when operating. Touching with it would
deactivate the insulation or cause leakage for electricity.
Extension cord is not recommended to use.
The appliance must be positioned so that the plug is accessible.
If the power cord is damaged ,it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
Protection from Moisture
Avoiding placing the refrigerator in a place where heavy moisture is present so as to
minimize possibility of rusty for its metal parts. Still more, the refrigerator is forbidden to
be directly sprayed by water, otherwise, poor insulation and current leakage would occur.
Protection from Heat
The refrigerator should be far away from any heat source or direct sunshine.
Fixing Stable
Floor on which refrigerator will be placed must be flat and solid. It should not be laid on
any soft material such as foam plastic, etc. If the refrigerator is not on the same level,
adjust the screws suitably. The refrigerator should not be placed near anything which
may echo.
Keep Away from Danger
It is inadvisable that the refrigerator is placed near any volatilizable or combustibles
such as gas, petrol, alcohol, lacquer and banana oil, etc. The above-mentioned objects
can not be stored in the refrigerator.
When fixed or moved, the refrigerator can not be set horizontally or declined to more
than 45 or upside-down.
3.Using Your Refrigerator
Temperature Control
The first time you turn the unit on, set the temperature control to "8" position.
The settings of the temperature control are "0,1,2,3,4,5,6,7,8". After 20 minutes,
adjust the temperature control setting to "4". The setting of "4" should be correct
for home or office use.
To turn the refrigerator off, turn the temperature control to "0".
Turning the temperature control to "0" position stops the cooling
cycle,but does not shut off the power to the refrigerator.
If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes
before restarting the unit. If you attempt to restart before this time delay, the
refrigerator will not start.
You should put your appliance in the coolest place in your room, which can save
energy consumption of your appliance. If the environment temperature is too high,
the temperature in the refrigerator may not get the target temperature.
Water getting into air inside the refrigerator by opening doors may form a layer of
frost inside, It will weaken the refrigerator when the frost is thick. While it is more
than 2mm thick, you should defrost.
Defrosting is operated manually. Before defrosting,take the bottle, then set the knob
of the temperature regulator to position"0"(where the compressor will stop working)
and leave the door open until ice and frost dissolve thoroughly deposited . In the case
of speeding up the defrosting, you may put a bowl of warm water(about 50 C )into the
evaporator, and be sure to set the knob of the temperature regulator to original position
after defrosting.
It's inadvisable to heat the evaporator directly with hot water or hair dryer while
defrosting to prevent deformation of the inner case.
It's also inadvisable to scrape of ice and frost which have been congealed together
with the food with sharp tool or wooden bars, so as not to damage the inner casing
or the surface of the evaporator.
If the supply cord of this appliance is damaged, it must only be replaced by
professional person or the repair shop appointed by the manufacturer.
Before you throw away your old refrigerator :take off the door, leave the shelves in
place, so that children may not easily climb inside.
Never allow children to operate, play with, or crawl inside the appliance.
5.Reversing the door
This refrigerator has the capability of either opening the door from the left or
right side. This unit is delivered to you with the door opening from the left side.
Should you desire to reverse the opening direction, please follow these
All parts removed must be saved to do the reinstallation of the door.
Reversal Refrigerator Door
1.Remove the upper hinge cap (7).
2.Remove the two screws blot (6) that connect the upper hinge (5) on the right
side of the cabinet top.
3.Carefully lift the door and place it on a padded surface to prevent scratching.
4.Remove the plug (9) and transfer it to the uncovered hole on the right side of
the unit. Be sure to press the button firmly into the hole.
5.Remove the two screws(1) that hold the lower hinge (2) on the right side of
the unit.
6.Remove the screw-type leveling front leg (4) and transfer it to the right side as
shown in the adjacent figure.
7.Set the door into it's new place making sure the pin enters the bushing at the
lower frame section (hole).
8.Secure the upper hinge (5) previously removed in step 3 on the left side of the
unit. Make sure the pin enters the bushing on the upper frame section (hole).
9.Loosely secure the lower left hinge (2) and do not tighten the bolts until the
door is in the closed position and leveled.
10.Insert the plug (9) on the uncovered holes (right side).
11.Replace the upper hinge cap (7).
Low Hinge
Adjustable Low Foot
Adjustable High Foot
Upper Hinge
Screw Bolt
Upper Hinge Cap
8 Shaft Sleeve
9 plug
The refrigerator should be cleaned and maintained once a month.
When performing maintenance, make absolutely sure that the power plug is first
disconnected from the power outlet.
Wipe the inner and outer surface of the refrigerator and its accessories with wet cloth.
If they are too dirty, scrub them with neutral detergent, and then clean them with water
and dry them with clean cloth. After this, a small quantify of glass wax is recommended
to polish the refrigerator surface with a flannelette.
For cleaning, don't use hot water, diluent, petrol, alcohol, kerosene, washing powder,
cleanser, alkaline detergent, acid, Chemical cloth, etc. So as not to damage the lacquer
coat and plastics. It is forbidden than the refrigerator is directly sprayed with water.
Otherwise, it would cause rusty or weaken the insulation.
Be careful to upkeep the sealing rubber bars of the doors. They should always be
If the plastic parts in refrigerator remain contaminated for a long time by oil
(animal or vegetable), they will be easy aged and possibly cracked. The drain pan
gets dirty very easily if it is not cleaned regularly, bad odours will be produced, get into
the habit of cleaning this pan regularly.
1. When the refrigerator does not work
Check if there is a power failure.
Check if the power plug is plugged into the power outlet.
Check that the fuse has not blown.
2. When the refrigerator is cooling excessively
The temperature control dial may be set too high.
If you place foodstuffs containing a lot of moisture directly under the cool air outlets,
they will freeze easily. This does not indicate a malfunction.
3. When the refrigerator is not cooling sufficiently
The food may be packed too tightly together which will block the flow of cool air.
You may have put something hot or a lot of food stuffs into the refrigerator .
The door may not have been closed properly.
The door gaskets may be damaged.
The refrigerator may not be ventilated.
There may be insufficient clearance between the refrigerator and the surfaces
Immediately both sides and above.
The temperature control dial may not be set properly.
4. When the defrosting water overflows inside the refrigerator and onto the floor.
Check that the drain pipe and the drain hose are not clogged.
Check that the drain pan is housed properly.
5. When the refrigerator's cabinet front heats up
In order to safeguard against condensation, there is an anticondensation, pipe
which heats up the cabinet front when running actuated. A warm cabinet front
does not indicate a malfunction.
6. When condensation form on the outside of the refrigerator.
Condensation may form on the outside when the humidity is high such as during
a wet season. This is the same result as the condensation formed when chilled
water is poured into a glass. It does not, therefore, indicate a failure, wipe dry with a
dry cloth.
7. When you hear a sound like water flowing .
A sound like water flowing is the refrigerant flowing. It does not Indicate a malfunction.
8. When the cabinet's side panel heats up
The side panel of the cabinet will heat up when the door is opened or closed frequently,
when starting the unit and when the unit operates in summer with high ambient outside
temperature, In such case, do not touch the panel, it results from the dissipation of the
heat from inside the cabinet, and it does not mean that something is wrong with the
‫ﺩﻟﻴﻞ ﺍﻟﺘﺸﻐﻴﻞ ﻟﻠﻤﺴﺘﺨﺪﻡ‬
‫ﻗﺒﻞ ﺇﺳﺘﺨﺪﺍﻡ ﻫﺬﺓ ﺍﻟﻮﺣﺪﺓ‪ ،‬ﺍﻟﺮﺟﺎء ﻗﺮﺍءﺓ ﻫﺬﺍ‬
‫ﺍﻟﺪﻟﻴﻞ ﺑﺪﻗﺔ‪ ،‬ﻭﺣﺎﻓﻆ ﻋﻠﻴﻪ ﻛﻤﺮﺟﻊ ﻓﻲ ﺍﻟﻤﺴﺘﻘﺒﻞ‪.‬‬
220V-240V 50Hz
‫اﻟﻮﻗﺎﻳﺔ ﻋﻦ اﻟﺤﺮارة‬
‫ﻳﺠﺐ ﺣﻔﻆ اﻟﺜﻼﺟﺔ ﺑﻌﻴﺪا ﻋﻦ اي ﻣﻮرد اﻟﺤﺮارة او ﺿﻮء اﻟﺸﻤﺲ اﻟﻤﺒﺎﺷﺮ‬
‫اﻟﺘﺮآﻴﺐ ﻋﻠﻰ اﻟﺜﺎﺑﺖ‬
‫ﻳﺠﺐ ان ﻳﻜﻮن اﻟﺴﻄﺢ اﻟﺬي ﺗﻮﺿﻊ ﻋﻠﻴﻪ اﻟﺜﻼﺟﺔ ﻣﺴﺘﻮﻳﺎ وﺻﻠﺒﺎ وﻻ ﺗﻀﻊ‬
‫اﻟﺜﻼﺟﺔ ﻋﻠﻰ اي ﻣﺎدة ﻧﺎﻋﻤﺔ ﻣﺜﻞ اﻟﺮﻏﻮة واﻟﺒﻼﺳﺘﻴﻚ وﻏﻴﺮهﺎ‪ .‬واذا ﻟﻢ ﺗﻜﻦ‬
‫اﻟﺜﻼﺟﺔ ﻣﺴﺘﻮﻳﺔ ﻓﻘﻢ ﺑﺘﻐﻴﻴﺮ اﻟﻘﻼووظ ﺑﺼﻮرة ﻣﻨﺎﺳﺒﺔ‪ .‬وﻳﺠﺐ ان ﻻ ﺗﻮﺿﻊ‬
‫اﻟﺜﻼﺟﺔ ﻣﻦ ﻣﻘﺮﺑﺔ اي ﺷﻴﺊ ﻳﻮﻟﺪ اﻟﺼﺪى‬
‫اﺣﻔﻆ ﺑﻌﻴﺪا ﻋﻦ اﻟﺨﻄﺮ‬
‫ﻻ ﻳﺴﺘﺤﺴﻦ وﺿﻊ اﻟﺜﻼﺟﺔ ﻣﺠﺎورة ﻻي ﺷﻴﺊ ﻣﺘﻄﺎﻳﺮ او ﻣﺤﺘﺮق ﻣﺜﻞ اﻟﻐﺎز‬
‫واﻟﺒﺘﺮول واﻟﻜﺤﻮل واﻟﻮرﻧﻴﺶ وزﻳﺖ اﻟﻤﻮز‬
‫وﺣﻴﻨﻤﺎ ﺗﺮآﺐ او ﺗﻨﻘﻞ اﻟﺜﻼﺟﺔ ﻳﺠﺐ ان ﻻ ﺗﻮﺿﻊ اﻓﻘﻴﺎ او ﻣﺎﺋﻠﺔ اآﺜﺮ ﻣﻦ ‪45‬‬
‫درﺟﺔ او ﻣﺘﻘﻠﺒﺔ‪.‬‬
‫‪ .3‬اﻧﺬارات‬
‫ان اﻟﻐﺬاء اﻟﻤﺎﺋﻲ او دﺧﻮل اﻟﻬﻮاء اﻟﻰ اﻟﺜﻼﺟﺔ اﺛﻨﺎء ﻓﺘﺢ اﻟﺒﺎب ﻗﺪ ﻳﻨﺸﺄ ﻃﺒﻘﺔ اﻟﺼﻘﻴﻊ ﻓﻲ اﻟﺪاﺧﻞ‪ .‬واذا‬
‫اﺻﺒﺢ اﻟﺼﻘﻴﻊ ﺳﻤﻴﻜﺎ ﻓﺘﻀﻌﻒ اﻟﺜﻼﺟﺔ ﻓﺎذا آﺜﺮت ﻣﻦ ﺳﻤﺎآﺔ ‪ 2‬ﻣﻢ ﻓﺘﺠﺐ ازاﻟﺔ اﻟﺼﻘﻴﻊ‪.‬‬
‫ﻳﻤﻜﻦ ازاﻟﺔ اﻟﺼﻘﻴﻊ ﻣﻦ ﺣﺠﺮة اﻟﺘﺠﻤﻴﺪ ﻳﺪوﻳﺎ وﻗﺒﻞ اﻻزاﻟﺔ اﺧﺮج اﻟﻐﺬاء ودرج اﻟﺜﻠﺞ واﻟﺮﻓﻮف وﺿﻊ زر‬
‫ﺗﻨﻈﻴﻢ درﺟﺔ اﻟﺤﺮارة ﻋﻠﻰ وﺿﻊ "‪) "0‬ﻳﻌﻨﻲ ﻻ ﺗﺸﺘﻐﻞ اﻟﻀﺎﻏﻄﺔ( واﺗﺮك اﻟﺒﺎب ﻣﻔﺘﻮﺣﺎ ﺣﺘﻰ ﻳﺬﺑﻞ اﻟﺜﻠﺞ‬
‫واﻟﺼﻘﻴﻊ اﻟﻤﺘﺮاآﻢ ﻓﻲ اﺳﻔﻞ ﺣﺠﺮة اﻟﺘﺠﻤﻴﺪ ﺑﺎﻟﺘﻤﺎم واﻣﺴﺢ اﻟﻤﺎء ﺑﻘﻤﺎش ﻧﺎﻋﻢ‪ .‬وﻟﺘﺴﺮﻳﻊ ﻋﻤﻠﻴﺔ ازاﻟﺔ‬
‫اﻟﺼﻘﻴﻊ ﻳﻤﻜﻦ ﻟﻚ وﺿﻊ ﻃﺎﺳﺔ ﻣﻦ اﻟﻤﺎء اﻟﺤﺎر )ﺣﻮاﻟﻲ ‪ 50‬درﺟﺔ( ﻓﻲ ﺣﺠﺮة اﻟﺘﺠﻤﻴﺪ وﻻ ﺗﻨﺴﻰ ﻟﻮﺿﻊ‬
‫زر ﺗﻨﻈﻴﻢ درﺟﺔ اﻟﺤﺮارة ﻋﻠﻰ اﻟﻮﺿﻊ اﻻﺻﻠﻲ ﺑﻌﺪ ازاﻟﺔ اﻟﺼﻘﻴﻊ‪.‬‬
‫وﻻ ﻳﺴﺘﺤﺴﻦ ﺗﺪﻓﺌﺔ ﺣﺠﺮة اﻟﺘﺠﻤﻴﺪ ﻣﺒﺎﺷﺮا ﺑﺎﻟﻤﺎء اﻟﺤﺎر او ﻣﺠﻔﻒ اﻟﺸﻌﺮ اﺛﻨﺎء ازاﻟﺔ اﻟﺼﻘﻴﻊ ﻟﺌﻼ ﺗﺘﺸﻮﻩ‬
‫اﻟﻌﻠﺒﺔ اﻟﺪاﺧﻠﻴﺔ‪.‬‬
‫وﻻ ﻳﺴﺘﺤﺴﻦ اﻳﻀﺎ آﺸﻂ اﻟﺜﻠﺞ واﻟﺼﻘﻴﻊ او ﺗﻔﺮﻳﺰ اﻟﻐﺬاء ﻣﻦ اﻟﺤﺎوﻳﺎت اﻟﺘﻲ ﺗﺠﻤﺪت ﻣﻊ اﻟﻐﺬاء ﺑﺎﺳﺘﻌﻤﺎل‬
‫اداة ﺻﺎرﻣﺔ او ﻗﻄﻊ اﻟﺨﺸﺐ ﻻﻧﻬﺎ ﺗﺘﻠﻒ اﻻﻃﺎر اﻟﺪاﺧﻠﻲ او ﺳﻄﺢ اﻟﻤﺒﺨﺎر‪.‬‬
‫اذا ﺗﻠﻒ ﺣﺒﻞ اﻟﻄﺎﻗﺔ ﻳﺠﺐ اﺳﺘﺒﺪاﻟﻪ ﻣﻦ ﻗﺒﻞ ﻣﺤﻞ ﺻﻴﺎﻧﺔ ﻣﻌﺘﻤﺪ ﺑﺎﻟﻤﻨﺘﺞ ﻻﻧﻪ ﻳﺤﺘﺎج اﻟﻰ اﻻدوات اﻟﺨﺎﺻﺔ‪.‬‬
‫وﺑﻌﺪ ﺗﺮآﻴﺐ اﻻداة ﺗﺎآﺪ ان اﻟﺴﺪادة ﺳﻬﻞ اﻟﻤﻨﺎل‪.‬‬
‫‪ .4‬ﺗﻐﻴﻴﺮ اﻟﺒﺎب اﻟﻤﻘﻠﻮب‬
‫ان هﺬﻩ اﻟﺜﻼﺟﺔ ﻣﺼﻤﻤﺔ ﺑﻤﻔﺎﺻﻞ اﻟﺒﺎب ﻋﻠﻰ اﻟﻴﻤﻴﻦ وان ﺗﺮد ﺗﻐﻴﻴﺮ ﺟﻬﺔ اﻟﻔﺘﺢ اﺗﺒﻊ اﻟﺘﻌﻠﻴﻤﺎت اﻟﺘﺎﻟﻴﺔ‬
‫ازل ﻗﻼووﻇﻴﻦ )‪ (1‬اﻟﺬﻳﻦ ﻳﺤﻤﻼن اﻟﻤﻔﺼﻞ اﻻﺳﻔﻞ )‪) (2‬ﺟﺎﻧﺐ اﻻﻳﻤﻦ( اﻟﻰ اﻻﻃﺎر‪ .‬واﻳﻀﺎ ازل‬
‫اﻟﺮﺟﻞ اﻻﻣﺎﻣﻲ اﻟﻤﺴﺘﻮي ﻧﻮع اﻟﺒﺮاﻏﻲ )‪(3‬‬
‫ازل اﻟﺮﺟﻞ اﻻﻳﺴﺮ اﻻﻣﺎﻣﻲ )‪ (4‬وﻧﻘﻠﻪ اﻟﻰ اﻟﺠﺎﻧﺐ اﻻﻳﻤﻦ‬
‫ارﻓﻊ اﻟﺒﺎب وﺿﻌﻪ ﻋﻠﻰ ﺳﻄﺢ ﻣﺤﺸﻮ ﻟﺌﻼ ﻳﺤﺪث اﻟﻜﺸﻂ ﻋﻠﻴﻪ وﻻ ﺗﻨﺴﻰ ﻻزاﻟﺔ اﻟﺰﻧﺒﺮك )‪ (5‬اﻟﻜﺎﺋﻦ‬
‫ﻓﻲ داﺧﻞ اﻟﺜﻘﺐ اﻟﻌﻠﻮي اﻻﻳﻤﻦ ﻟﻠﺒﺎب ودﺑﻮس اﻟﻌﻠﻮي اﻻﻳﻤﻦ )‪(6‬‬
‫ازل زر اﻟﺴﺪادة )‪ (7‬اﻣﺎم اﻟﺜﻘﺐ اﻟﻌﻠﻮي اﻻﻳﺴﺮ ﻟﻠﺒﺎب وﻧﻘﻠﻪ اﻟﻰ اﻟﺜﻘﺐ ﻏﻴﺮ اﻟﻤﺴﺘﻮر اﻟﻜﺎﺋﻦ ﻓﻲ اﻟﺠﺎﻧﺐ‬
‫اﻻﻳﻤﻦ وﻻ ﺗﻨﺴﻰ ﻟﻀﻐﻂ زر اﻟﺴﺪادة ﺑﺼﻮرة ﻣﺤﻜﻤﺔ ﻓﻲ اﻟﺜﻘﺐ‪.‬‬
‫ادﺧﻞ اﻟﻮﺗﺪ اﻟﻌﻮﻟﻲ )‪ (6‬واﻟﺬي ازﻳﻞ ﺳﺎﺑﻘﺎ ﻣﻦ اﻟﺠﺎﻧﺐ اﻻﻳﻤﻦ )ﺧﻄﻮة ‪ (3‬وﻧﻘﻠﻪ اﻟﻰ اﻟﺜﻘﺐ اﻻﺧﺮ اﻟﻜﺎﺋﻦ‬
‫ﻓﻲ اﻟﺠﺎﻧﺐ اﻻﻳﺴﺮ ﻟﻼﻃﺎر اﻟﻌﻠﻮي‪.‬‬
‫ادﺧﻞ اﻟﺰﻧﺒﺮك )‪ (5‬اﻟﺬي ازﻳﻞ ﺳﺎﺑﻘﺎ ﻓﻲ )ﺧﻄﻮة ‪ (3‬داﺧﻞ اﻟﺜﻘﺐ اﻟﻌﻠﻮي اﻻﻳﺴﺮ ﻟﻠﺒﺎب‬
‫ﺛﺒﺖ اﻟﺒﺎب ﻋﻠﻰ ﻣﻜﺎﻧﻪ ﺑﺎﻟﺘﻜﻴﺪ ان اﻟﻮﺗﺪ )‪ (6‬ادﺧﻞ اﻻﺟﻢ ﻋﻠﻰ ﻗﺴﻢ اﻻﻃﺎر اﻟﺴﻔﻠﻲ اﻟﻌﻠﻮي )ﺛﻘﺐ(‬
‫واﺛﻨﺎء ﻗﺒﺾ اﻟﺒﺎب ﺑﺤﺎﻟﺔ ﻣﻐﻠﻘﺔ ﻗﻢ ﺑﺮﺑﻂ اﻟﻤﻔﺼﻞ اﻟﺴﻔﻠﻲ اﻻﻳﺴﺮ )‪ (2‬واﻟﺬي هﻮ ﻣﺰال ﺳﺎﺑﻘﺎ ﻓﻲ ﺧﻄﻮة‬
‫ادﺧﻞ اﻟﻘﻼووﻇﻴﻦ )‪ (1‬اﻟﻤﻨﺰوﻋﻴﻦ ﺳﺎﺑﻘﺎ ﻓﻲ ﺧﻄﻮة )‪ (1‬وﺷﺪدهﻤﺎ‪.‬‬
‫ادﺧﻞ اﻟﺮﺟﻞ )‪ (3‬اﻟﻤﺴﺘﻮي ﻧﻮع اﻟﻘﻼووﻇﻴﻦ ﻋﻠﻰ اﻟﻤﻔﺼﻞ )ﺟﺎﻧﺐ اﻳﺴﺮ(‬
‫ﺻﻮرة ‪ :1‬ﻳﺸﻴﺮ اﻟﻰ اﻣﺎآﻦ اﻻﺟﺰاء ﻗﺒﻞ ﻋﻤﻠﻴﺔ ﺗﻌﻜﻴﺲ اﻟﺒﺎب‬
‫ﺻﻮرة ‪ :2‬ﻳﺸﻴﺮ اﻟﻰ اﻣﺎآﻦ اﻻﺟﺰاء ﺑﻌﺪ ﻋﻤﻠﻴﺔ ﺗﻌﻜﻴﺲ اﻟﺒﺎب‬
‫‪ .5‬اﻟﺼﻴﺎﻧﺔ‬
‫ﻳﺠﺐ ﺗﻨﻈﻴﻒ اﻟﺜﻼﺟﺔ وﺻﻴﺎﻧﺘﻬﺎ ﻣﺮة ﻓﻲ ﺷﻬﺮ‬
‫اﺛﻨﺎء اﻟﻘﻴﺎم ﺑﺎﻟﺼﻴﺎﻧﺔ ﺗﻴﻘﻦ اﻧﻪ ﺗﻢ ﺗﻘﻄﻴﻊ ﺳﺪادة اﻟﻄﺎﻗﺔ ﺗﻤﺎﻣﺎ ﻣﻦ ﻣﻨﻔﺬ اﻟﻜﻬﺮﺑﺎء‪.‬‬
‫اﻣﺴﺢ اﻟﺴﻄﺢ اﻟﺪاﺧﻠﻲ واﻟﺨﺎرﺟﻲ ﻟﻠﺜﻼﺟﺔ وﻣﻠﺤﻘﺎﺗﻬﺎ ﺑﻘﻤﺎش ﻣﺒﻠﻞ‪ .‬وان آﺎﻧﺖ ﻣﻠﻮﺛﺔ ﺟﺪا ﻗﻢ ﺑﺤﻜﻬﺎ‬
‫ﺑﺎﻟﻤﻄﻬﺮ اﻟﻄﺒﻴﻌﻲ ﺛﻢ ﻧﻈﻔﻬﺎ ﺑﺎﻟﻤﺎء وﺟﻔﻔﻬﺎ ﺑﻘﻤﺎش ﻧﻈﻴﻒ وﺑﻌﺪ ذﻟﻚ ﻳﺴﺘﺤﺴﻦ ﺗﺼﻘﻴﻞ ﺳﻄﺢ اﻟﺜﻼﺟﺔ‬
‫ﺑﻜﻤﻴﺔ ﻗﻠﻴﻠﺔ ﻣﻦ ﺷﻤﻊ اﻟﺰﺟﺎج ﺑﺎﺳﺘﻌﻤﺎل اﻟﻔﻼﻧﻴﻠﻴﺖ‬
‫ﻟﻠﺘﻨﻈﻴﻒ ﻻ ﺗﺴﺘﻌﻤﻞ اﻟﻤﺎء اﻟﺴﺎﺧﻦ‪ ،‬اﻟﻤﺸﻌﺸﻊ‪ ،‬اﻟﺒﺘﺮول‪ ،‬اﻟﻜﺤﻮل‪ ،‬اﻟﻜﻴﺮوﺳﻴﻦ‪ ،‬ﻣﺴﺤﻮق اﻟﻐﺴﻲ‪،‬‬
‫اﻟﻤﻨﻈﻒ‪ ،‬اﻟﻤﻄﻬﺮ اﻟﻔﻠﻮي‪ ،‬اﻟﺤﺎﻣﺾ‪ ،‬اﻟﻘﻤﺎش اﻟﻜﻴﻤﺎوي واﻣﺜﺎﻟﻬﺎ ﻻﻧﻬﺎ ﺗﺘﻠﻒ اﻟﻄﻼء اﻟﻠﻚ واﻟﺒﻼﺳﺘﻴﻚ‪.‬‬
‫وﻳﻤﻨﻊ رش اﻟﻤﺎء ﻋﻠﻰ اﻟﺜﻼﺟﺔ ﻣﺒﺎﺷﺮا واﻻ اﻧﻪ ﻳﻨﺘﺞ اﻟﺼﺪأ او ﻳﻀﻌﻒ اﻟﻌﺰل‪.‬‬
‫اهﺘﻤﻢ ﻋﻠﻰ ﺣﻔﻆ اﻟﻘﻄﻊ اﻟﻤﺴﺘﻄﻴﻠﺔ ﻟﻠﻤﻄﺎط اﻟﺨﺘﺎﻣﻴﺔ ﻟﻠﺒﺎب واﺣﻔﻈﻬﺎ ﻧﻈﻴﻔﺎ داﺋﻤﺎ‪.‬‬
‫وان ﺗﺴﺘﻤﺮ اﻻﺟﺰاء اﻟﺒﻼﺳﺘﻴﻜﻴﺔ ﻟﻠﺜﻼﺟﺔ ﻣﻠﻮﺛﺔ ﺑﺎﻟﺰﻳﺖ )ﺣﻴﻮاﻧﻲ او ﻧﺒﺎﺗﻲ( ﻟﻔﺘﺮة ﻃﻮﻳﻠﺔ ﻓﺎﻧﻪ ﺳﻬﻞ ان‬
‫ﺗﻜﻮن ﻗﺪﻳﻢ اﻟﻌﻬﺪ وﻣﻤﻜﻦ ان ﺗﻨﺼﺪع‪ .‬وان ﺣﻮض اﻟﺘﺼﺮﻳﻒ ﺳﻬﻞ اﻟﺘﻠﻮث ﺟﺪا اذا ﻟﻢ ﺗﻘﻢ ﺑﺘﻨﻈﻴﻔﻪ دورﻳﺎ‬
‫واﻳﻀﺎ ﺗﺨﺮج اﻟﻜﺮﻳﻬﺔ ﻓﻠﺬا ﺗﻌﻮد ﺗﻨﻈﻴﻒ هﺬا اﻟﺤﻮض ﺑﺸﻜﻞ ﻧﻈﺎﻣﻲ‪.‬‬
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF