Hisense | 55K760 | Product manual | Hisense 55K760 Product Manual

Hisense 55K760 Product Manual
55K760UW
QUICK SETUP GUIDE
Before using the TV, please read this guide thoroughly and retain it for future
reference. For more detailed instructions, please see the User Manual.
ES-A163012-1
English
Contents
Incorrect replacement of the battery may lead to the risk, including the
replacement of another similar or the same type. Do not expose batteries
to heat such as sun or fire or something like that.
The device should not be exposed to dripping and spraying and it cannot
be placed under objects filled with liquids.
Main plug is used as the disconnect device, the disconnect device shall
remain ready for operating.
NOTES
Excessive sound pressure from earphones and headphones can cause hearing loss.
Contents
Accessories List..............................................................................................................1
Installing the Stand .........................................................................................................2
Wall Brackets Installing Instructions ...............................................................................3
TV Front..........................................................................................................................4
TV Rear ..........................................................................................................................5
Making Connections .......................................................................................................5
Remote Control ............................................................................................................10
Turning the TV on for the First Time .............................................................................14
Specifications ...............................................................................................................15
Accessories List
The following accessories are included with TV:
TV
Base Stand
User Manual
INPUT
T.shift
Quick Setup Guide
Subtitle
OK
BACK
EXIT
VOLC
CH
Info
Quick Setup Guide
Spacer × 4
AAA Batteries × 4
Screws × 4
1
CH.List
EPG
APP
APP
Remote Control × 2
Screws × 4
Installing the Stand
Installing the Stand
CAUTION
Be sure to disconnect the A/C power cord before installing a stand or Wall-Mount
brackets.
The LED display is very fragile, and must be protected at all times when installing
the base stand. Be sure that no hard or sharp object, or anything that could scratch
or damage the LED display, comes into contact with it. DO NOT exert pressure on
the front of the TV at any time because the screen could crack.
Follow the illustrations and textual instructions below to complete the installation steps:
1. Carefully remove TV and top cushion from the carton box. Put the TV with top
cushion on the cushion, with its back upwards and the LCD downwards.
2. Remove the stand from the accessory bag and then Insert the stand into the
bottom slots of the TV.
Tip: Make sure to insert the legs according to the 'L' and 'R' directional marks that
are shown on the surface.
3. Secure the Base Stand to the TV with the 4 screws in accessary tightly.
Top Cushion
Screws: M4×12
Screws: M4×12
Right (R)
base stand
Left (L) base stand
NOTE
Product images are only for reference, actual product may vary in appearance.
2
Wall Brackets Installing Instructions
Follow the illustrations and textual instructions below to complete the installation
steps:
1. Carefully remove TV and top cushion from the carton box. Put the TV with top
cushion on the cushion, with its back upwards and the LCD downwards.
2.Take out the spacer and screw from the accessory bag.
3. Remove the screw and place the spacer to the corresponding position.
4.Attach the wall-mount bracket on the back of your TV.
M6×45
WALL-MOUNT BRACKET
8~10mm
3
2
M6
3
TV Front
TV Front
TV Bottom Panel
TV Back View
OK
Bluetooth device pairing
Remote sensor
Power indicator
Item
Description
Remote sensor
Receives remote signals from the remote control. Do not put
anything near the sensor, as its function may be affected.
Power indicator
The light is white in standby mode.
Select among the different input signal sources or put the TV
in standby mode, and you can turn on the TV when the TV in
standby mode.
Toggle the OK button left and right to adjust the volume.
Toggle the OK button up and down to select the channel.
NOTES
The Picture is Only for Reference.
It takes several seconds to power on the TV and load program. Do not rapidly turn the TV off
as it may cause the TV to work abnormally.
4
TV Rear & Making Connections
TV Rear
Power input
HDMI 3(4K@60Hz)
HDMI 4(4K@60Hz)
DIGITAL
AUDIO OUT
TV Bottom Panel
LAN
AV IN
VIDEO
L
R
Y
PB
PR
COMPONENT IN
CARD FACE FRONT
USB 3
DC 5V
1A(MAX) HDMI 2(ARC) HDMI 1(MHL) HEADPHONE SERVICE
USB 2
DC 5V
USB 1
0.5A(MAX)
ANT
COMMON INTERFACE
TV Side View
NOTES
Check the jacks for position and type before making any connections. Loose connections can
result in image or color problems. Make sure that all connections are tight and secure.
The TV may not be compatible with all external devices. To check compatibility, please refer
to the user manual of external device.
Do not connect external equipment while TV's power cord is plugged in. It may cause electric
shock.
5
Making Connections
ANT
Connect an outdoor VHF/UHF antenna or cable.
Outdoor
Antenna
TV JACK
Cable
or
ANT
ANT OUT
(not included)
Antenna Cable (75Ω)
VHF/UHF Antenna
COMMON INTERFACE
Insert the CI+ module for watching scrambled services like pay-tv channels or
some HD channels.
TV JACK
2
1
CAM CARD
SMART CARD
NOTES
Before you insert/remove the CI+ module, ensure that the TV is switched off.
Then insert the CI card into the CI+ module in accordance with the Service
Provider’s instructions.
Do not repeatedly insert or remove the Common Access Module as this may
damage the interface and cause a malfunction.
You must obtain a CI+ module and card from the service provider of the
channels you want to watch.
Insert the CI+ module with the SmartCard in the direction marked on the module
and SmartCard.
CI+ is not supported in some countries and regions; check with your authorized
dealer.
HDMI/COMP/AV
Connect a HDMI / Comp / AV cable from an external A/V equipment. No sound
connection is needed for HDMI to HDMI connection. If the signal resolution does not
match the specification table, you need to change the setting of device according to
the table. Please consult your device user manual for instruction.
· To select the HDMI / Component / AV
Press [Input] button, when the list of input Source appears, press [< / >] to select the
source [HDMI] / [COMPONENT] / [AV], then press [OK] to connect.
6
Making Connections
Video Effect:
BEST(HDMI)
BETTER
(COMP)
Y
Pb
Y
PB
PR
COMPONENT IN
VIDEO
L
R
Component
Pr
L
R
GOOD
(AV)
AV
Video Camera/
Set-top Box/
Satellite Receiver
Video
L
R
ARC
Connect an HDMI cable from an external digital audio system.
ARC enables the TV to directly output the digital sound through an HDMI cable.
Please note that it works only when the TV is connected to the audio receiver that
supports the ARC (Audio Return Channel) function.
When this port is used as the ARC function, it can't be used as signal input at the
same time.
TV JACK
Audio Amplifier/Speaker
HDMI
HDMI 2(ARC)
HDMI cable (not included)
MHL Connect an MHL cable (not provided) from your MHL-enabled device, such
as a cell phone.
TV JACK
HDMI 1(MHL)
MHL cable (not included)
MHL-enabled Device
NOTE
HDMI 1 is special for MHL device. Some of nonstandard DVD players may not be supported.
HEADPHONE
Connect Headphone for audio out of the TV.
The built-in speakers will be disabled once the headphone is connected.
TV JACK
HEADPHONE
Headphone (not included)
7
Making Connections
DIGITAL AUDIO OUT
system.
Connect an optical cable from an external digital audio
Optical SPDIF is a type of digital audio interconnect cable used in consumer
audio equipment to output audio over reasonably short distances. The signal is
transmitted over a fibre optical cable.
Before connecting a digital audio system to the Optical jack, you should decrease
the volume of both the TV and the system to avoid that the volume suddenly
become bigger.
TV JACK
Audio Amplifier/Speaker
DIGITAL
AUDIO OUT
Optical cable (not included)
USB
Connect the USB1.1, USB2.0 and USB3.0 devices such as hard drives, USB sticks
and digital cameras for browsing photos, listening music and watching recorded
movies. You can record live TV program (refer to PVR in user Manual). At the same
time update is also an easy thing and will be done just by plugging the USB with
the updating files into the USB interface.
TV JACK
USB
DC 5V
0.5A(MAX)
NOTES
When connecting a hard disk or a USB hub, always connect the mains adapter of
the connected device to the power supply.
If a USB 1.1 or USB2.0 device requires more than 500mA or 5V, the USB device
may not be supported. Max supported current for USB 3.0 device is 1A. Exceeding
the max supported current may result in damage or data loss.
If you want to store the video streaming of a DTV program, the transfer rate of the
USB storage device must not be less than 5MB/s.
LAN (Wired setup)
Connect your TV to your network by connecting the LAN port on the back of your
TV to an external modem or router using a LAN (Ethernet/Cat 5) cable. See the
illustration below.
8
Making Connections
· We recommend to use a modem or router that supports Dynamic Host
Configuration Protocol (DHCP). Modems and routers that support DHCP
automatically provide the IP address, subnet mask, gateway, and DNS, so you
don’t have to enter them manually. Most home networks already have DHCP.
TV JACK
LAN
IP Sharer (Router)
External Modem
(with DHCP server)
(ADSL / VDSL / Cable TV)
LAN Cable
LAN Cable
Modem Cable
Wireless setup
Connect your TV to your network wirelessly, you need a wireless router or modem.
See the illustration below.
· The TV’s built-in Wireless LAN Adapter supports the IEEE 802.11 ac/b/g/n
communication protocols. We recommend using IEEE 802.11ac router. Low
transfer rates for b/g/n may have the influence on the quality of streamed videos
and other media.
Wireless router with DHCP
Wireless LAN Adapter
built-in TV set
LAN Cable
NOTES
You must use the built-in Wireless LAN Adapter to use a wireless network because
the set doesn’t support external USB network adapter.
If the wireless router supports DHCP, your TV can connect more easily to the
wireless network.
If you apply a security system other than the systems listed below, it will not work with
the TV.
Ssecurity system : WPA, WEP, WPA2.
In order to guarantee smooth network, the distance between router and TV is less
than 10 meters.
9
Remote Control
11
12
1
2
1
POWER: Switch the TV on or into
standby mode
2
Special function buttons direct
selection of options
3
Adjust the volume
4
To speak a voice command press
and hold the VOICE button and say
a voice command
5
Navigation buttons ▲/▼/◄/►: Up/
Down/Left/Right
6
OK: Confirm the selection in the
OSD menus
7
BACK: Return to previous menu
8
HOME: Enter the Smart
9
CH + /-: Switch channel
10
Media content control function
buttons
11
Receive the voice
12
INPUT: Select input sources
13
K PA D : B r i n g s u p t h e v i r t u a l
keyboard.
14
EXIT: Exit the menu
3
13
4
5
6
14
7
8
9
10
Installing Batteries in the Remote Control
1. Lift the back cover to open the battery compartment of the remote control.
2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with
the (+) and ( - ) ends indicated in the battery compartment.
3. Close the battery compartment with the cover.
1 Remove the battery
compartment cover
2 Insert the batteries
10
3 Close the battery compartment cover
Remote Control
Pairing the Remote Control
Keep the remote control close to the bluetooth device pairing . Press the voice key to open
the voice control function and hold the blue button until the red light on the remote control
remains lit, and wait until the remote pairing is complete.
If the remote control pairing is successful, the Screen will appear "Remote control pairing is
successful. Welcome to experience".
If the remote control pairing fails, the screen will appear "Remote control pairing fails. Please
try again".
NOTES
Pairing the remote control from the bluetooth device pairing
needed within 10cm.
When the TV into standby mode does not support Bluetooth pairing.
If you want to release pairing, hold the blue button, the indicator light flashes purple and then
disappears, if the remote control unpairing is successful the indicator light will turn red when
press any button on the remote control.
Voice Control
Press the voice key to open the voice control function. Press the voice key, the screen
outgoing voice helper, then you can enter a voice command, the corresponding voice control
function will be executed. After a period of time no longer the voice input, the remote control
automatically turns off Mike.
Please strictly for voice control operations in accordance with the following voice commands.
If you perform the non-provision of voice command, there will not recognize the voice Case
commands.
Supported audio content
Volume Control
For example, Set volume to 25 / Volume 10 / Volume up / Mute.
Channel Switching
For example, Channel 3.
Source switching
For example, Change to HDMI2 / Switch input source.
System Setting
For example, Open settings / Audio settings / Start the network settings menu / Go to picture
settings.
Application Management
For example, Youtube / Open Youtube / Start Youtube.
NOTE
When a voice conversation from the microphone hole best of 10cm ~ 15cm.
11
Remote Control
Power Standby button:
Power on/ Standby
INPUT
Source selecting button
Select a channel or input
numbers
Start Timeshift
T.shift
Subtitle
Quick Setup
Fast access to the
all applications
Navigation buttons
(Up/Down/Left/Right)
Returns to the
previous menu
Confirm button / Display
the on-screen keyboard
OK
BACK
EXIT
VOL
CH
Enter the Live TV screen
Volume (up/down)
Exit the menu or exit
the application
Display the Home screen
Channel (up/down)
Mute and restore sound
Media content control
function buttons
Display the channel
list on the screen
Display subtitles in the
Live TV
Special function buttons
Display the current
program information
Info
CH.List
EPG
APP
APP
12
Display the Electronic
Program Guide (DTV mode)
Quick access buttons
to apps
Remote Control
Installing Batteries in the Remote Control
1. Slide the back cover to open the battery compartment of the remote control.
2. Insert two AAA size batteries. Make sure to match the ( + ) and ( - ) ends of the
batteries with the ( + ) and ( - ) ends indicated in the battery compartment.
3. Close the battery compartment cover.
1
Gently push and slide
2
Insert the batteries
3
Gently push and slide
NOTES
Product image is only for reference, actual product may vary in appearance.
Dispose of your batteries in a designated disposal area. Do not throw the batteries into a fire.
Do not mix battery types or combine used batteries with new ones.
Remove depleted batteries immediately to prevent battery acid from leaking into
the battery compartment.
If you do not intend to use the remote control for a long time, remove the batteries.
Batteries should not be exposed to excessive heat, such as sunshine, heat
registers, or fire.
Battery chemicals can cause a rash. If the batteries leak, clean the battery
compartment with a cloth. If chemicals touch your skin, wash immediately.
Remote Control Operation Range
1. Point the remote control at the TV within
no more than 5 metres from the remote
control sensor on the TV and within 60°
in front of the TV.
2. The operating distance may vary
depending on the brightness of the
room.
13
Remote sensor
Turning the TV on for the First Time
Turning the TV on for the First Time
1. Connect the mains cable to the mains socket after you have completed all the
connections.
2. The first time you turn the TV on, it will go straight into the Installation Guide. It will
assist you to specify the Language, Location and Network.
3. Press the [ / / < / >] to navigate the menu and change the settings. Press the [OK]
button to confirm.
Language
Select your desired language to be displayed on the menu.
Location
Select the location and time zone where you will operate the TV.
Accept EULA and set up network.
Network
Complete
If your TV does not detect an Ethernet connection, then it will
select Wireless automatically, select your network from the list
that displays and move to the next screen.
You have completed the Wizard setup, please select the desired
mode.
14
Specifications
Features, appearance and specifications are subject to change without notice.
If you encountered difficulty when setting up your TV, we suggest you refer to the
troubleshooting tips in the User Manual.
Model Name
Without
Stand(mm)
Dimension
Weight
With Stand
(mm)
55"
Width: 1241
Height: 737
Depth: 105
Width: 1241
Height: 763
Depth: 241
Without
Stand(kg)
22.7
With Stand
(kg)
23.5
Active Screen
Size(Diagonal)
55 inches
Screen resolution
3840×2160
Audio power
10W +10W
Power consumption
Please refer to the rating label.
Power supply
100V - 240V
Receiving
systems
Analog
Digital
50Hz/60Hz
PAL-D/K, B/G, I SECAM-D/K, B/G, L/L’
DVB-T/T2, DVB-C
Environmental
conditions
Temperature: 5°C - 45°C
Humidity: 20% - 80% RH
Atmospheric pressure: 86 kPa - 106 kPa
Component Input
480 I / 60 Hz, 480 P / 60 Hz, 576 I /50 Hz, 576 P /50 Hz,
720 P / 50 Hz, 720 P / 60 Hz, 1080 I / 50 Hz, 1080 I / 60
Hz, 1080 P / 50 Hz, 1080 P / 60 Hz
HDMI Input
60 Hz (640×480, 800×600, 1024×768)
60 Hz (480 I, 480 P, 720 P, 1080 I, 1080 P)
50 Hz (576 I, 576 P, 720 P, 1080 I, 1080 P)
24 Hz 30 Hz (3840×2160 HDMI 1,2)
24 Hz 30 Hz 50 Hz 60 Hz (3840×2160 HDMI 3,4)
Made in China
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising