JL Audio | MBT-CRXv2 | Owner's Manual | JL Audio MBT-CRXv2 Owner's Manual

JL Audio MBT-CRXv2  Owner's Manual
Mounting & Installation
What’s Included
(1) MBT-CRXv2 Bluetooth
controller/receiver
(1) Threaded fastening collar
(1) Thin round gasket
(1) Thick round gasket
IP67
WATER
RESISTANT
(1) Square adaptor plate
(1) Square adaptor gasket
(4) Stainless steel mounting screws
(1) User Manual
Weatherproof Bluetooth® Controller / Receiver
Installation Applications
Product Description
The MBT-CRXv2 is a water-resistant (IP67
rated) Bluetooth® receiver designed for
marine and powersports applications. It can
be used as a stand-alone Bluetooth® source
unit/receiver, connecting directly to an
amplifier. It can also be used as an add-on
Bluetooth® controller/receiver, connected
to an existing head unit’s line-level/auxiliary
inputs. The MBT-CRXv2 is not designed to
drive loudspeakers directly.
MBT_CRX_MANv2-071018.indd 1
This product is designed for operation in
12 volt, negative-ground electrical systems.
Using this product in systems with positive
ground and/or voltages other than 12 volts
may result in damage to the product and
will void the warranty. This product is not
certified or approved for use in aircraft.
Safety Considerations
•W
henever possible, mount this product
in a dry, well-ventilated location that does
not interfere with other factory installed
electronic devices. If a dry environment is
not available, a location that is not exposed
to heavy splashing may be used.
• While this product is designed to be waterresistant, it should never be submerged
under water for prolonged periods or
subjected to high-pressure water spray.
• Do not mount in an engine compartment
or in any areas of extreme heat.
• E nsure this product is securely installed so
that it does not come loose in the event of a
collision/sudden jolt or as a result of repeated
vibrations during normal operation.
• Check before drilling to make sure that you
will not be drilling into an exterior panel/
hull, fuel tank, gas/brake line, wiring harness,
or other vital system.
The design of the MBT-CRXv2 requires just
a single hole for installation. Its easy-touse threaded-collar mounting system can
accommodate installations in flat surfaces up
to 1.75 inches (4.5 cm) thick. A front-mounted
adaptor plate is included for installations in
panels exceeding 1.75 inches (4.5 cm) thick,
or where rear access is limited or not possible.
Refer to the diagrams below for your specific
mounting application.
Standard Collar-Mount Installation
• Do not run system wiring outside or
underneath the vehicle/vessel. This is an
extremely dangerous practice, which can
result in severe damage/injury.
• Protect all system wires from sharp
edges (metal, fiberglass, etc.) by carefully
routing them, tying them down and using
grommets and loom where appropriate.
Front-Mount Adaptor Installation
• Secure all wiring as needed, using cable
ties or wire clamps to protect them from
moving parts and sharp edges.
• Do not replace the power wire fuse with one
of a different value. Never bypass the fuse.
7/10/18 12:05 PM
Wiring Diagram
Pairing Your Device
(required for operation)
1. E nsure your streaming device has Bluetooth®
enabled and that the MBT-CRXv2 is on
(backlit in blue). The JL Audio logo on the
MBT-CRXv2 will blink to indicate it is in
pairing mode.
2. W
ithin your streaming device’s Bluetooth®
setup menu, select “MBT-CRXv2” from the list
of pairable devices.
3. When successfully connected, the
JL Audio logo on the MBT-CRXv2 will stop
blinking and remain lit. A single beep will be
heard through the connected audio system.
Pairing Considerations
Multiple devices can be paired to the
MBT-CRXv2, but only one streaming device
can connect at one time.
Note: If optional connection is made to a head
unit’s remote turn-on output, the head unit will
turn the MBT-CRXv2 on/off and the MBT-CRXv2
power button will no longer operate.
The MBT-CRXv2 will remember the last device
that was connected to it and reconnect with
it automatically. If that streaming device is not
active, then other paired streaming devices can
connect manually, or new streaming devices
can be paired.
Pairing Considerations cont’d
When a connected streaming device is out
of range for more than one minute, the
MBT-CRXv2 will automatically disconnect this
streaming device and return to pairing mode
(JL Audio logo will blink). When that same
device comes back into range, it should be
reconnected to the MBT-CRXv2 manually.
Controlling Audio Playback
Once connected, use the controls on the
MBT-CRXv2 to adjust volume up/down, track
selection and play/pause.
Specifications
Bluetooth® Profile
Bluetooth® Core
Specification
Frequency Response
Outputs
Output Voltage
Signal to Noise Ratio
Input Operating Voltage
Current Draw
Remote Turn-on
Output Capacity
Fuse Rating
Connection Range*
A2DP (High-Quality, Stereo Audio)
Version 4.0 with
Qualcomm® aptX™ audio
20 Hz – 18 kHz (±1dB)
One Stereo Pair, Low-Level RCA Plugs
2V RMS
93 dB (20 Hz – 20 kHz)
8 – 28 VDC
48 mA (at idle)
64 mA (at full output)
350 mA (max)
2A Mini ATC
Up to 35 ft / 11 m
*Maximum range is achieved in line-of-sight installations, actual range
will vary based on installation specifics.
Control Legend
IP67 Water Resistance Rating
This product has been tested to withstand immersion in water,
up to 1 meter (3.28 ft.) deep, for up to 30 minutes (when properly installed). Note - while designed to be water resistant, this
product should never be submerged under water for prolonged
periods or subjected to activity that creates pressure on it that
exceeds its depth rating.
2-Year Limited Warranty (U.S.A.)
Visit www.jlaudio.com for warranty details.
For Service Information in the U.S.A. please call JL Audio
customer service: (954) 443-1100 during normal business hours
(Eastern Time) • JL Audio, Inc • 10369 N Commerce Parkway,
Miramar, FL 33025
International Warranties:
Products purchased outside the United States of America are
covered only by that country’s distributor and not by JL Audio, Inc.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by JL Audio, Inc. is under license. Qualcomm aptX is a product of Qualcomm
Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated,
registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies
International, Ltd., registered in the United States and other countries and any use of such marks by
JL Audio, Inc. is under license.
071018 • Printed in China
MBT_CRX_MANv2-071018.indd 2
7/10/18 12:05 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising