Shure | SE315-425-535 | User guide | Shure SE315-425-535 Sound Isolating™ Earphones User guide

Shure SE315-425-535 Sound Isolating™ Earphones User guide
SE315 SE425 SE535
Sound Isolating™ Earphones
The Shure high-definition sound isolating earphones, SE315, SE425, and SE535, user guide.
Version: 3 (2019-K)
Shure Incorporated
Table of Contents
SE315 SE425 SE535Sound Isolating™ Earphones
Sound Isolating™ Earphones
Removing the Earphones
5
Choosing a Sleeve
5
Cleaning the Earphone Nozzle
6
Maintenance and Cleaning
6
3
3
Detachable Cable
3
Wearing the Earphones
3
Specifications
6
Inserting the Earphones
4
Accessories
7
Changing Sleeves
5
Certifications
8
2/8
Shure Incorporated
SE315 SE425 SE535
Sound Isolating™ Earphones
Sound Isolating™ Earphones
Shure Sound Isolating™ Earphones, built with balanced armature speakers, deliver a detailed soundstage free from outside
noise. The powerful and stylish Shure SE earphones come with a detachable cable, adapters, a durable carrying case, and in­
terchangeable Sound Isolating sleeves for a comfortable and personalized fit.
Detachable Cable
You may need to detach the cable from the earphones to attach optional components or to replace the cable if it becomes
damaged. To prevent accidental separation, the connector has a snug fit. Take special care to prevent damage to the earphone
and connector.
• Do not use pliers or other tools.
• Grasp the connector and the earphone as close as possible to where they join.
• Pull straight apart—do not twist. Cable is a snap fit, not threaded.
Note: If you pull at an angle, the connector will not detach.
• Do not pull on the cable or put any pressure on the earphone nozzle.
• Listen for a click when connecting.
• When reattaching the cable, match the "L" and "R" markings. For clear cables and earphones, match the color dots
(Red=Right, Blue=Left).
3/8
Shure Incorporated
Wearing the Earphones
The following are some suggested ways of wearing the earphones.
Wear the cable over the ear and secure it behind the head to help keep the earphones in place during physical activity.
Tighten the cable and take up slack by raising the cable cinch.
Inserting the Earphones
Insert the earphones so they form a tight seal. The fit of the earphone can greatly affect sound quality.
Important: If there seems to be a lack of low frequency response (bass), this means that the earphone sleeve is not forming a tight seal. Gently push the ear­
phone deeper into the ear canal or try a different sleeve.
Warning: Do not push the earphone sleeve beyond the ear canal opening.
4/8
Shure Incorporated
Changing Sleeves
• Twist and pull to remove the sleeve from the nozzle.
• Slide on a new sleeve so that it completely covers the barb and the nozzle.
Caution: If the barb or any of the nozzle is exposed, the sleeve is not properly installed. Replace sleeves if they do not tightly grip the nozzle. To ensure proper
fit and performance, use only sleeves supplied by Shure (unless using custom molded sleeves).
Removing the Earphones
Grasp the body of earphone and gently twist to remove.
Note: Do not pull on cable to remove earphone.
Choosing a Sleeve
Select an earphone sleeve that provides the best fit and sound isolation. It should be easy to insert, fit comfortably, and easy to
remove.
Soft Flex Sleeves: In small, medium, and large sizes. Made from pliable rubber.
Soft Foam Sleeves: Compress the foam sleeve between your fingers and insert into the ear canal.
Hold in place for about ten seconds while the foam expands.
5/8
Shure Incorporated
Triple-Flange Sleeves: If desired, use scissors to trim the stem on the sleeve.
Cleaning the Earphone Nozzle
If you notice a change in sound quality, remove the sleeve and check the nozzle of your earphone. If nozzle is blocked, clear
obstruction by using wire loop end of cleaning tool.
If no obstruction is found or if sound quality does not improve, replace the sleeve with a new sleeve.
Caution: When cleaning, do not force any object through the earphone nozzle! This will damage the earphone sound filter.
Warning: The cleaning tool is only to be used to clean the earphones. Any other use, such as using the tool to clean ears or foam sleeve, could result in injury.
The cable connectors to the earphones may collect debris or other deposits that can affect audio quality. If this happens, disconnect the cables and clean them
using a dry cotton swab.
Maintenance and Cleaning
Careful maintenance ensures a tight seal between the sleeve and nozzle, improving sound quality and product safety.
• Keep the earphones and sleeves as clean and dry as possible.
• To clean sleeves, remove them from earphones, gently rinse in warm water and air dry. Foam sleeves require a longer
drying time. Inspect for damage and replace if necessary. Ear sleeves must be completely dry before reusing.
• Wipe the earphones and sleeves with mild antiseptic to avoid infections. Do not use alcohol-based disinfectants.
• Do not expose earphones to extreme temperatures.
• Replace sleeves if they do not fit properly.
• Do not attempt to modify this product. Doing so will void the warranty and could result in personal injury and/or product
failure.
Specifications
Transducer Type
SE535/535LTD Red
Triple balanced-armature drivers
SE425
Dual balanced-armature drivers
6/8
Shure Incorporated
SE315
Single High-Definition MicroDriver
Sensitivity
at 1 kHz
SE535/535LTD Red
119 dB SPL/MW
SE425
109 dB SPL/MW
SE315
116 dB SPL/MW
Impedance
at 1 kHz
SE535/535LTD Red
36 Ω
SE425
22 Ω
SE315
27 Ω
Frequency Range
SE535
18 Hz –19 kHz
SE535LTD Red
18 Hz –19 .5 kHz
SE425
20 Hz –19 kHz
SE315
22 Hz –18 .5 kHz
Input Connector
Gold­plated 3.5 mm (1/8”) stereo mini jack plug with 6.35 mm (1/4”) threaded adapter
Net Weight
30 g (1 oz.)
Operating Temperature
-18°C to 57°C (0°F to 135°F)
Storage Temperature
-29°C to 74°C (-20°F to 165°F)
Accessories
•
•
•
•
•
•
Earphone Sleeves
Replacement Cables
Carrying Cases
Music Phone Accessory Cables
Volume Control
Adapters
For information about earphone accessories and other Shure products visit:
http://www.shure.com/americas/products/accessories/earphones
7/8
Shure Incorporated
Certifications
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: info@shure.de
8/8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising