Shure | AD1 | User guide | Shure AD1 Bodypack Transmitter User guide

Shure AD1 Bodypack Transmitter User guide
AD1
Bodypack Transmitter
AD1 Axient Digital Bodypack Transmitter User Guide
Version: 8 (2020-A)
Shure Incorporated
Table of Contents
Menu Parameter Descriptions
AD1Bodypack Transmitter
3
WARNING
3
AD1 Axient Digital Bodypack Transmitter
Features
3
4
Optional Accessories
4
AD1 Transmitter Overview
4
Transmitter Controls
6
Locking the Interface
6
Home Screen Display
7
Battery Installation
7
Setting the AA Battery Type
8
AA Battery Installation
8
9
Battery Life
9
Checking Battery Info
9
Important Tips for Care and Storage of Shure Recharge­
able Batteries
10
AA Batteries and Transmitter Runtime
Radio Menu
12
Audio Menu
12
Utilities Menu
13
3
Included Components
Shure SB900A Rechargeable Battery
10
IR Sync
14
Setting the Frequency Manually
14
Updating Firmware
15
Firmware Versioning
15
Updating the Transmitter
15
Wearing the Bodypack Transmitter
15
RF Mute
16
Safe Start
16
Input Overload
17
Matching Audio Levels with Offset
17
Tone Generator
17
Specifications
18
Input Connector Diagrams
20
Frequency Bands and Transmitter RF Power
20
LICENSING INFORMATION
Australia Warning for Wireless
Menu Parameters
12
22
23
11
Tips for Editing Menu Parameters
11
Menu Map
12
Certifications
Information to the user
23
23
2/24
Shure Incorporated
AD1
Bodypack Transmitter
WARNING
• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat
above 140°F (60°C), or incinerate.
• Follow instructions from manufacturer
• Only use Shure charger to recharge Shure rechargeable batteries
• WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.
• Never put batteries in mouth. If swallowed, contact your physician or local poison control center
• Do not short circuit; may cause burns or catch fire
• Do not charge or use battery packs other than Shure rechargeable batteries
• Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like
WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries.
Note: Use only with the included power supply or a Shure-approved equivalent.
AD1 Axient Digital Bodypack Transmitter
AD series bodypack transmitters deliver impeccable audio quality and RF performance with wide-tuning, High Density (HD)
mode, and encryption. The transmitter features durable metal construction, AA or SB900A rechargeable power (with dockable
charging), and TA4 or LEMO3 connector options.
Features
Performance
•
•
•
•
•
•
20 Hz to 20 kHz range with flat frequency response
Automatic input staging optimizes gain setting
AES 256-bit encryption-enabled for secure transmission
>120 dB dynamic range
100 meter (300 feet) line-of-sight operating range
Selectable modulation modes optimize performance for spectral efficiency
◦ Standard – optimal coverage, low latency
◦ High density – dramatic increase in max system channel count
• Built-in tone generator and RF markers to facilitate walk-testing
• Switchable Power Levels = 2/10/35 mW (region dependent)
• Frequency Diversity selection using two bodypacks
Design
• TA4 or LEMO3 audio connector option
3/24
Shure Incorporated
•
•
•
•
Backlit LCD with easy to navigate menu and controls
Rugged metal construction
Flexible ¼ wave antenna
Menu and power lockout
Power
• Over 8 hours continuous use with 2 x AA alkaline batteries
• Shure SB900A lithium-ion rechargeable battery provides extended battery life, precision metering, and zero memory effect
• External charging contacts for docked charging
Included Components
AA alkaline batteries (2)
80B8201
¼ wave antenna
Varies by Region
Threaded TAF4 adapter
WA340
Zipper bag
26A13
Belt clip
44A12547
Optional Accessories
Bodypack rechargeable lithium-ion battery
SB900A
Y-Cable for bodypack transmitters
AXT652
LEMO Y-cable for bodypack transmitters
AXT652LEMO3
Instrument cable
WA302
Replacement belt clip
44A12547
Instrument cable with right angle 1/4" connector
WA304
Mute Switch for Bodypack
WA661
Mute Switch for 2 Bodypacks
WA662
AD1 Transmitter Overview
① RF Antenna
For RF signal transmission.
② Display
4/24
Shure Incorporated
View menu screens and settings. Press any control button to activate the backlight.
③ Infrared (IR) Port
Align with the receiver IR port during an IR Sync for automated transmitter tuning and setup.
④ Control Buttons
Use to navigate through parameter menus and to change settings.
⑤ Battery Compartment
Requires two AA batteries or Shure SB900A rechargeable battery.
⑥ AA Battery Adapter
Use to secure AA batteries. Remove when using a Shure SB900A battery.
⑦ SMA Connector
Connection point for RF antenna.
⑧ Power Switch
Powers the unit on or off.
⑨ Power LED
◦ Green = unit is powered on
◦ Red = low battery, Mute Mode enabled, input overload, or battery error (see Troubleshooting)
⑩ Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Note: A LEMO connector model variation of this transmitter is available.
5/24
Shure Incorporated
Transmitter Controls
Use the controls to navigate through parameter menus and change values.
exit
Acts as a 'back' button to return to previous menus or parameters without confirming a value change
enter
Enters menu screens and confirms parameter changes
∨∧
Use to scroll through menu screens and to change parameter values
Tip: Use the following shortcuts for quick setup:
• Hold the ∧ button while powering on to lock or unlock the transmitter controls.
• Hold the exit button while powering on to enter the Safe Start menu.
6/24
Shure Incorporated
Locking the Interface
Lock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon appears on the
home screen when a lock is enabled.
1. From the Utilities menu, navigate to Locks and select one of the following lock options:
◦ None: The controls are unlocked
◦ Power: The power switch is locked
◦ Menu: The menu parameters are locked
◦ All: The power switch and menu parameters are locked
2. Press enter to save.
Tip: To quickly unlock a transmitter: Press enter twice, select None, and press enter.
Home Screen Display
The home screen shows transmitter information and status.
There are four pieces of information that you can choose to see on the home screen. Use the arrow buttons to select one of
the following choices:
Name
Frequency Setting
Group (G) and Channel (C)
Device ID
The following icons indicate transmitter settings:
Battery runtime in hours and minutes or bar display
Key: Displayed when encryption is enabled
Lock: Displayed when controls are locked. Icon will flash if
access is attempted to a locked control (power or menu).
STD: Standard Transmission Mode
HD: High Density Transmission Mode
RF Mute Engaged: Displayed when RF output is muted
7/24
Shure Incorporated
Battery Installation
① Accessing the Battery
Compartment
② Installing Batteries
Press the side tabs on the bodypack and open the battery door as shown to access the bat­
tery compartment.
• AA Batteries: Place batteries (note polarity markings) and AA Adaptor as shown and
close the door
• Shure SB900A Battery: Place battery as shown (note polarity markings). Remove the
AA adapter and set it aside. Close the door to secure the battery.
Note: If using AA batteries, set the battery type using the transmitter menu.
Setting the AA Battery Type
To ensure accurate display of transmitter runtime, set the battery type in the transmitter menu to match the installed AA battery
type.
Note: If a Shure SB900A rechargeable battery is installed, selecting a battery type is not necessary and the battery type will display Shure.
1. Navigate to the Utilities and select Battery.
2. Use the ▼▲ buttons to select the installed battery type:
◦ Alkaline = Alkaline
◦ NiMH = Nickel Metal Hydride
◦ Lithium = Lithium Primary
3. Press enter to save.
AA Battery Installation
Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely.
8/24
Shure Incorporated
Shure SB900A Rechargeable Battery
Shure SB900A lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50%
capacity in one hour and reach full charge within three hours.
Single chargers and multiple bay chargers are available to recharge the Shure batteries.
Caution: Only charge Shure rechargeable batteries with a Shure battery charger.
Battery Life
UHF
1.x
2 mW/10 mW
35 mW
2 mW/10 mW
30 mW
SB900A
9 hours
4:30 hours
6 hours
5 hours
alkaline
8 hours
3:30 hours
5:30 hours
3:45 hours
The values in this table are typical of fresh, high quality batteries. Battery runtime varies depending on the manufacturer and
age of the battery.
Checking Battery Info
When using a Shure rechargeable battery, the receiver and transmitter home screens display the number of hours and minutes
remaining.
Detailed information for the battery is displayed Battery menu of the transmitter: Utilities > Battery
•
•
•
•
•
•
•
Battery: The chemistry type of for the installed battery (Shure, Alkaline, Lithium, NiMH)
Bars: Indicates the number of bars displayed
Time: Battery runtime
Charge: Percentage of charge capacity
Health: Percentage of current battery health
Cycle Count: Total of the number of charging cycles for the installed battery
Temperature: Battery temperature reported in Celsius and Fahrenheit
9/24
Shure Incorporated
Important Tips for Care and Storage of Shure Rechargeable Batteries
Proper care and storage of Shure batteries results in reliable performance and ensures a long lifetime.
•
•
•
•
Always store batteries and transmitters at room temperature
Ideally, batteries should be charged to approximately 40% of capacity for long-term storage
Periodically clean the battery contacts with alcohol to maintain ideal contact
During storage, check batteries every 6 months and recharge to 40% of capacity as needed
For additional rechargeable battery information, visit www.shure.com.
AA Batteries and Transmitter Runtime
Transmitters are compatible with the following AA battery types:
• Alkaline
• Nickel Metal Hydride (NiMH)
• Lithium Primary
A 5­segment battery indicator representing the charge level of the transmitter battery is displayed on the screens of the trans­
mitter and receiver. The following table contains the approximate remaining transmitter runtime in hours:minutes.
Alkaline Batteries
Battery Runtime ( hours:minutes)
UHF
1.x
Battery Indicator
2 mW/10
mW
35
mW
2 mW
/10
mW
30
mW
8:00 to 6:00
3:30
to
3:00
5:30 to
4:15
3:45
to
3:00
6:00 to 4:00
3:00
to
2:00
4:15 to
3:00
3:00
to
2:15
4:00 to 1:45
2:00
to
1:30
3:00 to
1:45
2:15
to
2:00
<1:45
<1:30
<1:45
<2:00
10/24
Shure Incorporated
Battery Runtime ( hours:minutes)
UHF
1.x
Battery Indicator
2 mW/10
mW
35
mW
2 mW
/10
mW
30
mW
<0:45
<0:45
<0:45
<0:45
<0:15
<0:15
<0:15
<0:15
Menu Parameters
The Main menu organizes the available transmitter parameters into three sub-menus:
• Radio
• Audio
• Utilities
Tip: Use the arrow buttons to scroll between the sub-menus.
Tips for Editing Menu Parameters
• To access the menu options from the home screen, press the enter button. Use the arrow buttons to access additional
menus and parameters.
• A menu parameter will blink when editing is enabled
• To increase, decrease or change a parameter, use the arrow buttons
• To save a menu change, press enter
• To exit a menu without saving a change, press exit
11/24
Shure Incorporated
Menu Map
Menu Parameter Descriptions
Radio Menu
Freq
Press the enter button to enable editing of a group (G:) channel (C:) or frequency (MHz). Use the arrow buttons to adjust
the values. To edit the frequency, press the enter button once to edit the first 3 digits, or twice to edit the second 3 digits.
Power
Higher RF power settings can extend the range of the transmitter.
Note: Higher RF power settings decrease battery runtime.
Output
Sets the RF output to On or Mute.
◦ On: RF signal is active
◦ Mute: RF signal is inactive
Audio Menu
Pad
Adjust the pad to avoid overloading the audio input. Select -12 dB or Off.
Offset
Adjust Offset level to balance mic levels when using two transmitters or when assigning multiple transmitters to receiver
slots. Adjustment range: -12 dB to +21 dB.
Polarity
12/24
Shure Incorporated
Selectable polarity assignment for the audio input connector:
◦ Pos: Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of XLR output)
and the tip of the TRS output.
◦ Neg: Positive pressure on microphone diaphragm produces negative voltage on pin 2 (with respect to pin 3 of XLR output)
and the tip of the TRS output.
Mute
When enabled, the power switch is configured as a mute switch for the audio:
◦ Power switch on: Audio signal on
◦ Power switch off: Audio signal muted
Exit mute mode to return the power switch to its normal functionality.
Tone Gen
Transmitter will generate a continuous test tone:
◦ Freq: The tone can be set to 400 Hz or 1000 Hz.
◦ Level: Adjusts the output level of the test tone.
Utilities Menu
Device ID
Assign a device ID of up to 9 letters or numbers.
Locks
Locks the transmitter controls and power switch.
◦
◦
◦
◦
None: The controls are unlocked
Power: The power switch is locked
Menu: The menu parameters are locked
All: The power switch and menu parameters are locked
Marker
When enabled, press the enter button to drop a marker in Wireless Workbench.
Battery
Displays battery information:
◦
◦
◦
◦
◦
Battery Life: Runtime reported in bar display and time (hours:minutes)
Charge: Percentage of charge capacity
Health: Percentage of current battery health
Cycle Count: Total of the number of charging cycles for the installed battery
Temperature: Battery temperature reported in Celsius and Fahrenheit
About
Displays the following transmitter information:
◦ Model: Displays the model number
◦ Band: Displays the tuning band of the transmitter
◦ FW Version: Installed firmware
13/24
Shure Incorporated
◦ HW Version: Hardware version
◦ Serial Num: Serial number
Reset All
Restores all transmitter parameters to factory settings.
IR Sync
Use IR Sync to form an audio channel between the transmitter and receiver.
Note: The receiver band must match the band of the transmitter.
1.
2.
3.
4.
5.
Select a receiver channel.
Tune the channel to an available frequency using group scan or manually turn to an open frequency.
Power on the transmitter.
Press the SYNC button on the receiver.
Align the IR windows between the transmitter and the receiver so that the IR LED illuminates red. When complete,
Sync Success! appears. The transmitter and receiver are now tuned to the same frequency.
Note:
Any change to the encryption status on the receiver (enabling/disabling encryption) requires a sync to send the settings to the
transmitter. New encryption keys for the transmitter and receiver channel are generated on every IR sync, so to request a new
key for a transmitter, perform an IR sync with the desired receiver channel.
Setting the Frequency Manually
The transmitter can be manually tuned to a specific group, channel, or frequency.
1. Navigate to the Radio menu and select Freq.
2. Scroll to select G: and C: to edit the group and channel, or select the frequency parameter (MHz). When editing the fre­
quency, press enter once to edit the first 3 digits, or twice to edit the last 3 digits.
3. Use the ∧∨ buttons to adjust the group, channel, or frequency.
4. Press enter to save, and then press exit when finished.
14/24
Shure Incorporated
Updating Firmware
Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are devel­
oped to incorporate additional features and enhancements. To take advantage of design improvements, you can upload and in­
stall new versions of the firmware by using the Shure Update Utility. The Shure Update Utility is available for download from
http://www.shure.com/.
Firmware Versioning
When performing an update, first download firmware to the receiver, and then update transmitters to the same firmware version
to ensure consistent operation.
The firmware numbering for Shure devices uses the following format: MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all
devices on the network (including transmitters), must have the same MAJOR and MINOR firmware version numbers (e.g.,
1.2.x).
Updating the Transmitter
1. Download the firmware to the receiver.
2. Access the following menu from the receiver: Device Configuration > Tx Firmware Update.
3. Align the IR ports between the transmitter and the receiver. IR ports must be aligned for the entire download, which can
take 50 seconds or longer.
Tip: The red alignment LED will turn on when the alignment is correct.
4. Press ENTER on the receiver to begin the download to the transmitter. The receiver will display the progress of the up­
date as a percentage.
Wearing the Bodypack Transmitter
Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown.
For best results, the belt should be pressed against the base of the clip.
Tip: The clip can removed and rotated 180 degrees to increase mounting options.
15/24
Shure Incorporated
RF Mute
RF Mute prevents transmission of the audio by suppressing the RF signal while allowing the transmitter to remain on. The
home screen displays RF MUTED in this mode.
1. From the Radio menu, navigate to Output.
2. Choose one of the following options:
◦ On: RF signal is active
◦ Mute: RF signal is disabled
3. Press enter to save.
Turning the transmitter off and on or replacing the battery will restore Output to On.
Safe Start
Power on in Safe Start mode to prevent interference with other devices. Hold the exit button while powering on your device un­
til the Safe Start menu appears.
16/24
Shure Incorporated
Safe Start menu options:
• RF: Mute or On
• Locks: None, Pwr, Menu, All
Use the navigation buttons to make changes.
Tip: To exit the Safe Start menu, cycle the power or momentarily remove the battery.
Note: Previous settings for locks and RF will be retained when the transmitter is powered on in Safe Start.
Input Overload
The OVERLOAD message appears when the audio input experiences a high­level signal. The power LED turns red as an addi­
tional indicator of an overload. Reduce the input signal or enable the input pad to remove the overload condition.
Tip: To enable the input pad, navigate to Audio > Pad and select -12 dB.
Matching Audio Levels with Offset
When linking two or more transmitters to a receiver, there may be a difference in volume levels between microphones or instru­
ments. If this occurs, use the Offset function to match the audio levels and eliminate audible volume differences between trans­
mitters. If using a single transmitter, set Offset to 0 dB.
1. Turn on the first transmitter and perform a sound check to test the audio level. Turn off the transmitter when finished.
2. Turn on the second transmitter and perform a sound check to test the audio level. Repeat for any additional transmit­
ters.
3. If there is an audible difference in the sound level between the transmitters, navigate to the Offset menu (Audio >
Offset) in the transmitter to increase or decrease the Offset in realtime to match the audio levels.
17/24
Shure Incorporated
Tone Generator
The transmitter contains an internal tone generator that produces a continuous audio signal. The tone is helpful when conduct­
ing a sound check or for troubleshooting the audio signal chain. The level of the tone is adjustable from -60 dB to 0 dB and the
frequency can be set to 400 Hz or 1000 Hz.
Tip: Always start with the level set to -60 dB to avoid overloading speakers or headphones.
1. From the Audio menu select Tone Gen.
2. Set the frequency to 400 Hz or 1000 Hz.
3. Select Level and use the arrow buttons adjust the value between -60 dB and 0 dB.
Turn off the tone by selecting Off from the menu or by cycling the transmitter power.
Specifications
Mic Offset Range
-12 to 21 dB (in 1 dB steps)
Battery Type
Shure SB900A Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW
Shure SB900A
up to 9 hours
alkaline
up to 8 hours
See Battery Runtime Chart
Dimensions
86 mm x 66 mm x 23 mm (3.4 in. x 2.6 in. x 0.9 in.) H x W x D
Weight
155 g (5.0 oz.), without batteries
Housing
Cast Metal
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
18/24
Shure Incorporated
Note: Battery characteristics may limit this range.
Storage Temperature Range
-29°C (-20°F) to 74°C (165°F)
Note: Battery characteristics may limit this range.
Audio Input
Connector
4-Pin male mini connector (TA4M) or Lemo Connector
Configuration
Unbalanced
Impedance
4-Pin male mini connector (TA4M)
910 kΩ
Lemo Connector
8.2 kΩ
Maximum Input Level
1 kHz at 1% THD
Pad Off
8.5 dBV (7.5 Vpp)
Pad On
20.5 dBV (30 Vpp)
Preamplifier Equivalent Input Noise (EIN)
System Gain Setting ≥ +20
-120 dBV, A-weighted, typical
RF Output
Connector
SMA
Antenna Type
1/4 wave
Impedance
50 Ω
Occupied Bandwidth
<200 kHz
Channel-to-Channel Spacing
Standard Mode
350 kHz
High Density Mode
125 kHz
varies by region
19/24
Shure Incorporated
Modulation Type
Shure Axient Digital Proprietary
Power
2 mW, 10 mW, 35 mW
See Frequency Range and Output Power table, varies by region
Input Connector Diagrams
TA4M
LEMO
Frequency Bands and Transmitter RF Power
Band
Frequency Range (MHz)
RF Power (mW)***
G53
470 to 510
2/10/35
G54
479 to 565
2/10/20
G55†
470 to 636*
2/10/35
G56††
470 to 636
2/10/35
G57
470 to 616*
2/10/35
G62
510 to 530
2/10/35
H54
520 to 636
2/10/35
K53
606 to 698*
2/10/35
K54△
606 to 663**
2/10/35
20/24
Shure Incorporated
Band
Frequency Range (MHz)
RF Power (mW)***
K55
606 to 694
2/10/35
K56◇
606 to 714
2/10/35
K57△
606 to 790
2/10/35
K58
622 to 698
2/10/35
L54
630 to 787
2/10/35
R52
794 to 806
2/10
JB
806 to 810
2/10
X51
925 to 937.5
2/10
X55
941 to 960
2/10/35
Z16†††
1240 to 1260
2/10/30
*with a gap between 608 to 614 MHz.
**with a gap between 608 to 614 MHz and a gap between 616 to 653 MHz.
***power delivered to the antenna port.
†operation mode varies according to region. In Brazil, High Density mode is used. The maximum power level for Peru is
10mW.
††Limited to 10mW for Indonesia.
†††Z16 for Japan only
△Output power limited to 10 mW above 608 MHz.
◇Korea defines power as conducted (ERP) which is 1dB less then declared in table.
K55 606-694 MHz
Country Code
Frequency Range
Code de Pays
Gamme de frequences
Codice di paese
Gamme di frequenza
Código de país
Gama de frequencias
Länder-Kürzel
Frequenzbereich
A, B, BG, CH, CY, CZ, D, DK, EST, F
*
FIN, GB, GR, H, HR, I, IRL, IS, L, LT
*
M, N, NL, P, PL, RO, S, SK, SLO, TR
*
all other countries
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
21/24
Shure Incorporated
G56 470-636 MHz
Country Code
Frequency Range
Code de Pays
Gamme de frequences
Codice di paese
Gamme di frequenza
Código de país
Gama de frequencias
Länder-Kürzel
Frequenzbereich
A, B, BG, CH, CY, CZ, D, DK, EST, F
*
FIN, GB, GR, H, HR, I, IRL, IS, L, LT
*
M, N, NL, P, PL, RO, S, SK, SLO, TR
*
all other countries
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
K57 606-790 MHz
Country Code
Frequency Range
Code de Pays
Gamme de frequences
Codice di paese
Gamme di frequenza
Código de país
Gama de frequencias
Länder-Kürzel
Frequenzbereich
A, B, BG, CH, CY, CZ, D, DK, EST, F
*
FIN, GB, GR, H, HR, I, IRL, IS, L, LT
*
M, N, NL, P, PL, RO, S, SK, SLO, TR
*
all other countries
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for
possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to
operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability de­
pends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the
appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.
低功率電波輻射性電機管理辦法
第十二條
22/24
Shure Incorporated
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功
能。 第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使
用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機
設備之干擾。
Australia Warning for Wireless
This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating
frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band.
WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band.
No user­operated control of power, frequency, or other parameters are available beyond those specified in this operating man­
ual.
Please follow your regional recycling scheme for batteries, packaging, and electronic waste.
Certifications
Certified under FCC Part 15 and FCC Part 74.
Certified by ISED in Canada under RSS-210.
FCC ID: DD4AD1G55, DD4AD1G57, DD4AD1K53, DD4AD1K54, DD4AD1X55. IC: 616A-AD1G55, 616A-AD1K53.
Meets essential requirements of the following European Directives:
• WEEE Directive 2012/19/EU, as amended by 2008/34/EC
• RoHS Directive EU 2015/863
Note: Please follow your regional recycling scheme for batteries and electronic waste
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address: http://www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: EMEAsupport@shure.de
Information to the user
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa­
tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
23/24
Shure Incorporated
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Canada Warning for Wireless
This device operates on a no­protection, no­interference basis. Should the user seek to obtain protection from other radio ser­
vices operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Econom­
ic Development Canada’s document Client Procedures Circular CPC­2­1­28, Voluntary Licensing of Licence­Exempt Low­Pow­
er Radio Apparatus in the TV Bands.
Ce dispositif fonctionne selon un régime de non‑brouillage et de non‑protection. Si l’utilisateur devait chercher à obtenir une
certaine protection contre d’autres services radio fonctionnant dans les mêmes bandes de télévision, une licence radio serait
requise. Pour en savoir plus, veuillez consulter la Circulaire des procédures concernant les clients CPC‑2‑1‑28, Délivrance de
licences sur une base volontaire pour les appareils radio de faible puissance exempts de licence et exploités dans les bandes
de télévision d’Innovation, Sciences et Développement économique Canada.
This device operates on frequencies shared with other devices. Consult the Federal Communications Commission White
Space Database Administration website to determine available channels in your area prior to operation.
This device contains licence­exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop­
ment Canada’s licence­exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
24/24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising