Shure | ANI4OUT | User guide | Shure ANI4OUT Audio Network Interface User guide

Shure ANI4OUT Audio Network Interface User guide
ANI4OUT
概述
uses a single network cable to receive audio and power through Power over
Ethernet (PoE).
General Description
The Shure Audio Network Interface converts 4 channels of Dante™ digital
audio into discrete analog signals. Connect to a processing device with
analog connections (audio processors, video codecs, and loudspeaker systems, for example) to fully integrate networked audio and analog equipment
in a single system. Available in XLR and block connector versions, each box
Model Variations
ANI4OUT-XLR: Four XLR outputs (balanced audio)
ANI4OUT-BLOCK: Four 3-pin block connector outputs (balanced audio)
Hardware and Installation
Hardware
Block Connector Model
௟
௠
௢
௣
OUTPUT
sig/clip
1
3
PoE
power
1
2
network
3
network audio
4
2
4
encryption
reset
௤
௡
௟
௢
sig/clip
1
power
2
network
3
network audio
4
encryption
Front Panel
XLR Model
©2017 Shure Incorporated
1/28
ANI4OUT
Shure Incorporated
௠
௣
OUTPUT
PoE
reset
௤
Rear Panel
௟
௢
sig/clip
1
power
2
network
3
network audio
4
encryption
Front Panel
① Output Level Indicators (Signal/Clip)
Tri-color LEDs indicate the audio signal level for each channel. Adjust levels in the web application to avoid clipping.
2/28
LED State
Audio Signal Level
Off
less than -60 dBFS
Green
-60 dBFS to -18 dBFS
Yellow
-18 dBFS to -6 dBFS
Red
-6 dBFS or more
2017/10/30
ANI4OUT
Shure Incorporated
② Audio Outputs
Analog balanced audio outputs connect to an analog device. Set the output level in the web application to match the input sensitivity of the analog device.
XLR pin assignments:
1
Shield
2
+
3
-
Block connector pin assignments: See front panel labels
③ Chassis Ground Screw
Provides an optional connection for microphone shield wire to chassis ground
Note: only applies to block connector version
④ LED Indicators
Power: Power over Ethernet (PoE) present
Note: Note: Use a PoE injector if your network switch does not supply PoE.
Network: Network connection active
Network Audio: Dante™ audio present on the network
Note: Error details are available in the event log in the web application.
Encryption: Not currently supported
LED Status
Activity
Off
No active signal
Green
Device is operating successfully
Red
Error has occurred. See event log for details.
⑤ Dante Network Port
Connects to a network switch to receive Dante™ audio, Power over Ethernet (PoE), and data from the control software.
⑥ Reset Button
Resets the device settings back to the factory default
乙太網路供電 (PoE)
乙太網路供電
本裝置需要 PoE 才能工作。它與 0 和 3 PoE 源均相容。
乙太網路供電的工作方式如下:
•
一台提供 PoE 的網路交換機
•
一個 PoE 注射裝置
安裝和機架固定
有兩個固定解決方案可用於安裝
CRT1 19"
:
最多支援 3 個裝置;可固定於機架中或桌面下
支援單一裝置以固定在桌面下
固定裝置
使用固定硬體套件中包含的螺釘以固定
2017/10/30
。
可朝任一方向固定。根據下列圖表,在適當的孔中從底部插入螺釘:
3/28
ANI4OUT
Shure Incorporated
如圖所示對齊孔洞,在單一裝置固定托盤中固定單一裝置
4/28
2017/10/30
ANI4OUT
Shure Incorporated
如圖所示對齊孔洞,在 19" 機架托盤中最多固定三個裝置。
機架耳片設定
可將最多 3 個
2017/10/30
的組合固定在單一 19 英吋機架空間中。可調節的機架耳片支援標準設備機架中或桌面下的安裝固定。
5/28
ANI4OUT
Shure Incorporated
標準 19" 機架固定
1. 使用指向前方的固定孔對齊耳片。
2. 安裝將耳片支撐在托盤上的兩個螺釘,如圖所示。
桌面下固定
1. 使用指向上方的固定孔對齊耳片。
2. 安裝將耳片支撐在托盤上的兩個螺釘,如圖所示。
6/28
2017/10/30
ANI4OUT
Shure Incorporated
桌面下安裝
1. 以桌面下的所需位置支撐托盤
2. 使用鉛筆標記桌面下固定孔洞的位置。
3. 鑽出要使用螺釘的 4 個孔。托盤中的孔洞直徑為 7.1 毫米。
4. 將元件安裝到托盤中
5. 使用 4 顆螺絲安裝,以將托盤固定在桌面下
重設
重設按鈕位於後側面板的小孔內。使用迴紋針或其他小工具按壓該按鈕。
有兩個硬體重設功能:
網路重設(按住按鈕 4-8 秒鐘)
將所有 Shure 控制和音訊網路 IP 設定重設為出廠預設值
完全重設出廠設定(按住按鈕超過 8 秒鐘)
將所有網路和
恢復為出廠預設值。
軟體重設選項
若要簡單恢復設定,而不進行完整的硬體重設,請使用下列選項之一:
Reboot Device 在
(設定 > 出廠預設值)中,有Reboot Device按鈕,若裝置中斷網路連接,可簡單向裝置循環供電。重新啟動裝置後,會保留所有設定。
若要將音訊設定恢復為出廠預設值(排除设备名称、IP 設定和密碼),請選擇Load Preset並選擇預設設定預設。
2017/10/30
7/28
ANI4OUT
Shure Incorporated
Signal Flow and Connections
Connections and Signal Flow
8/28
2017/10/30
ANI4OUT
Shure Incorporated
Input: Dante™ Digital Audio
A single network cable delivers 4 channels of audio and Power over Ethernet (PoE). Use Dante™ Controller to route audio channels from the network to the
network interface.
Output: Analog (4 XLR or Block Connectors)
Each output sends a discrete audio channel to connect to an analog device.
Setting up the Audio Network
Shure networked conferencing systems are comprised of Microflex Advance microphones and network interfaces, which operate entirely on a Dante™ network.
Additional hardware, including network switches, computers, loudspeakers, and audio processors are described in the hardware component index.
Shure components shown in this diagram:
Microflex Advance Microphones
The MXA910 and MXA310 are equipped with Dante outputs, and connect directly to a network switch.
Audio Network Interfaces
The interfaces are used to connect analog devices such as loudspeakers and analog microphones to the network.
ANI4IN: Converts 4 analog signals (separate XLR and block connector models available) into Dante™ digital audio signals.
ANI4OUT: Converts 4 channels of Dante™ audio from the network into analog signals.
2017/10/30
9/28
ANI4OUT
Shure Incorporated
This diagram shows the entire signal path through a networked conference system. Signals from the near end and far end are exchanged through an audio
processor connected to a phone system, or through a computer connected to the internet. Analog microphones connect to the network through the Shure ANI4IN,
while loudspeakers connect through the Shure ANI4OUT.
10/28
2017/10/30
ANI4OUT
Shure Incorporated
This diagram shows Microflex Advance components in context, with two rooms communicating through video codecs.
Controlling Hardware and Audio Over the Network
Audio and hardware settings are managed through a computer connected to the same network.
2017/10/30
11/28
ANI4OUT
Shure Incorporated
Shure Hardware and Audio
Each Microflex Advance component has a web application which provides mixing and configuration tools to optimize sound quality.
Expanded Control for Analog Devices
Analog devices that are connected to the network through a Shure network interface (ANI4IN/ANI4OUT) benefit from additional remote control: Volume levels,
equalization, and signal routing are managed through the web application. For example, adjusting loudspeaker volume or muting a wired microphone, which
would normally be done from the hardware, can now be controlled remotely over the network.
Dante™ Signal Routing
Signal routing between devices is managed through Dante Controller software, provided by Audinate™ .
Summing
The Audio Network Interface provides channel summing to combine Dante™ signals from the network, and send them over a single analog output. This makes
it possible to send all channels to a device with a limited amount of analog input channels. Mixer functionality does not change; audio channels are simply sent
as one combined signal.
Note: When summing is enabled, a limiter is activated to prevent signal overloading. The limiter never applies to the direct outputs, and only affects the summed
signal.
To enable, select one of the summing options in the toolbar at the top of the mixer in the channels tab.
1
2
3
1
2
1+2
2
3
3+4
4
3+4
4
1
1
2
1
1 +2
1+2+3+4
2
3
3
3
4
4
4
Encryption
Audio is encrypted with the Advanced Encryption Standard ( AES -256), as specified by the US Government National Institute of Standards and Technology
(NIST) publication FIPS-197. Shure devices that support encryption require a passphrase to make a connection. Encryption is not supported with third-party
devices.
To activate encryption:
1. Open the 设置 menu and select the 總述 tab.
2. Select the Enable Encryption checkbox.
3. Enter a passphrase. All devices must use the same passphrase to establish an encrypted connection.
Important: For encryption to work:
•
Encryption must be universally enabled or disabled on all connected Shure devices
•
AES67 must be disabled in Dante Controller to turn encryption on or off. AES67 encryption is currently not supported.
Software Installation, Management, and Security
軟體安裝和裝置發現
Shure Web Device Discovery 應用程式用於存取適用於 Shure 裝置的
。如果加密設定不同,將在接收機液晶顯示面板上顯示
啟,提供綜合的裝置管理手段。和裝置聯網的任何電腦均可透過該應用存取 GUI。
12/28
可以在網路瀏覽器中開
2017/10/30
ANI4OUT
•
Chrome
•
Safari
•
Firefox
•
Internet Explorer
Shure Incorporated
1. 安裝 Shure Web Device Discovery 應用程式,該程式可從 www.shure.com 取得
2. 按兩下元件以開啟介面。
存取
Shure Web Server Discovery 應用程式可透過基於 Web 的圖表化使用者介面搜尋網路中的所有舒爾裝置。執行這些步驟,安裝軟體並存取
:
① 安裝 Shure Discovery 應用程式
從 www.shure.com 下載並安裝 Shure Discovery 應用程式。這樣可以在電腦上自動安裝所需的 Bonjour 裝置檢測工具。
② 連接網路
確保電腦和硬體位於相同的網路中。
③ 啟動 Discovery 應用程式
應用程式將顯示採用圖表化使用者介面的所有舒爾裝置。
④ 識別硬體
按兩下裝置可在網路瀏覽器中開啟圖表化使用者介面 (GUI)。
⑤ 給裝置設定標籤
(建議)
將裝置的 DNS 名稱加入書籤,可以在不需要 Shure Discovery 應用程式的情況下存取圖表化使用者介面。
Accessing the Web Application without the Discovery App
If the Discovery application is not installed, the web application can be accessed by typing the DNS name into an internet browser. The DNS name is derived
from model of the unit, in combination with the last three bytes (six digits) of the MAC address, and ending in .local.
Format Example: If the MAC address of a unit is 00:0E:DD:AA:BB:CC, then the link is written as follows:
ANI4IN: http://ANI4IN-aabbcc.local
ANI4OUT: http://ANI4OUT-aabbcc.local
固件更新
固件是在每個功能控制元件中的嵌入式軟體。定期開發的新固件版本中包含附加功能和效能增強部分。若要享受設計改進帶來的優勢,可利用「Shure Update
Utility」工具上傳和安裝新版本的固件。軟體可以從網站 http://www.shure.com 中下載。
當 Shure MXW 音訊網路介面連接 Shure Olympus 元件時,它們的固件必須在更新 MXW 音訊網路介面固件之前在一台裝置上進行更新。嘗試同時更新所
有裝置將導致介面在固件更新後重新啟動,將遺失與其他聯網元件的連接。
按照以下步驟更新固件:
確保裝置在更新期間具有穩定的網路連接。在完成更新之前,請勿關閉裝置電源。
1. 將裝置和電腦接入同一網路(設為相同子網)。
2. 下載和安裝 Shure Update Utility。
3. 開啟應用程式。
4. 按一下 Check For Updates... 檢視可供下載的新固件版本。
5. 選擇所需的固件,按Download下載至固件庫中。
6. 從Update Devices標籤中選擇新固件,然後按下Send Updates...開始固件更新,這會重寫裝置現有固件。
固件版本要求
Shure MXW 裝置採用多通訊協定的網路,這些協定同時確保裝置正常工作。推薦的最佳做法是所有
個裝置的固件版本,可開啟元件使用者介面,然後查看 Settings>About.
Shure MXW 裝置採用相同的版本。若要檢視網路中每
Shure 裝置的固件格式為 MAJOR.MINOR.PATCH。(例如在固件「1.6.2」中,1 為主要固件等級,6 為次要固件等級,2 為補丁固件等級。)在相同子網工作
的裝置至少應擁有相同主要和次要版本號。
•
主要版本號不同的裝置不相容。
•
補丁固件版本號的差異可能會產生不希望出現的不一致性。
2017/10/30
13/28
ANI4OUT
Shure Incorporated
Parametric Equalizer
Maximize audio quality by adjusting the frequency response with the parametric equalizer.
Common equalizer applications:
•
Improve speech clarity
•
Reduce noise from HVAC systems or video projectors
•
Reduce room irregularities
•
Adjust frequency response for reinforcement systems
Setting Filter Parameters
Adjust filter settings by manipulating the icons in the frequency response graph, or by entering numeric values. Disable a filter using the check-box next to the
filter.
Filter Type
Only the first and last band have selectable filter types.
Parametric: Attenuates or boosts the signal within a customizable frequency range
Low Cut: Rolls off the audio signal below the selected frequency
Low Shelf: Attenuates or boosts the audio signal below the selected frequency
High Cut: Rolls off the audio signal above the selected frequency
High Shelf: Attenuates or boosts the audio signal above the selected frequency
Frequency
Select the center frequency of the filter to cut/boost
Gain
Adjusts the level for a specific filter (+/- 30 dB)
Q Width
Adjusts the range of frequencies affected by the filter. As this value increases, the bandwidth becomes thinner.
14/28
2017/10/30
ANI4OUT
Shure Incorporated
Equalizer Applications
Conferencing room acoustics vary based on room size, shape, and construction materials. Use the guidelines in following table.
2017/10/30
EQ Application
Suggested Settings
Treble boost for improved speech intelligibility
Add a high shelf filter to boost frequencies greater than 1 kHz by 3-6 dB
HVAC noise reduction
Add a low cut filter to attenuate frequencies below 200 Hz
15/28
ANI4OUT
Shure Incorporated
EQ Application
Suggested Settings
Identify the specific frequency range that "excites" the room:
Set a narrow
1.
Q value
Reduce flutter echoes and sibilance
Increase the gain to between +10
2. and +15 dB, and then experiment with
frequencies between 1 kHz and 6 kHz to pinpoint the range of flutter echoes
or sibilance
Reduce the gain at the identified 3.
frequency (start between -3 and -6 dB) to
minimize the unwanted room sound
Identify the specific frequency range that "excites" the room:
Set a narrow
1.
Q value
Reduce hollow, resonant room sound
Increase the gain to between +10
2. and +15 dB, and then experiment with
frequencies between 300 Hz and 900 Hz to pinpoint the resonant frequency
Reduce the gain at the identified 3.
frequency (start between -3 and -6 dB) to
minimize the unwanted room sound
Custom Presets
Use presets to quickly save and recall settings. Up to 10 presets can be stored on each device to match various seating arrangements. A preset saves all device
settings except for the , IP Settings, and Passwords. Importing and exporting presets into new installations saves time and improves workflow. When a preset
is selected, the name displays above the preset menu. If changes are made, an asterisk appears next to the name.
Note: Use the default settings preset to revert to the factory configuration (excludes
, IP Settings, and Passwords).
Open the presets menu to reveal preset options:
save as preset:
Saves settings to the device
load preset:
Opens a configuration from the device
import from file:
Downloads a preset file from a computer onto the device. Files may be selected through the browser or dragged into the import window.
export to file:
Saves a preset file from the device onto a computer
Event Log
Event Log
The event log provides a detailed account of activity from the moment the device is powered on. The log collects up to 1,000 activity entries and time-stamps
them relative to the last power cycle. The entries are stored in the internal memory, and are not cleared when the device is power-cycled. The Export feature
creates a CSV (comma separated values) document to save and sort the log data.
Refer to the log file for details when troubleshooting or consulting with Shure Systems Support.
To view the event log:
1. Open the Help menu
2. Select View Event Log
Severity Level
Information
An action or event has been successfully completed
Warning
An action cannot be complete, but overall functionality is stable
Error
A problem has occurred that could inhibit functionality.
Log Details
Description
Provides details on events and errors, including IP address and subnet mask.
Time Stamp
Power cycles:days:hours:minutes:seconds since most recent boot-up.
Event ID
Indicates event type for internal reference.
Tip: Use the filter to narrow down results. Select a category heading to sort the log.
16/28
2017/10/30
ANI4OUT
Shure Incorporated
Levels and Metering
•
Line level (0 dB)
Adjusting Input levels
•
Aux level (-20 dB)
Input Levels
1. Check the source level before it reaches the Network Interface:
•
Microphone level (-46 dB)
⁃
Verify that the networked microphones or other Dante™ sources
are operating at nominal output levels.
⁃
Levels for Microflex Advance™ microphones are adjustable through
their web application.
LED Signal and Clipping Indicators
Each analog output channel has a corresponding LED:
Green: Audio signal present
Red: Audio signal is clipping and should be attenuated.
2. Adjust the digital gain in the Network Interface web application:
⁃
Use the faders or manually enter a gain value.
⁃
The digital gain adjusts the level of the signal before it reaches the
analog circuitry.
⁃
Set these levels as high as possible without reaching the peak level
(0 dB) on the meter.
Note: the meters in the web application are not affected by the Analog Gain
(dB) setting.
Pre- and Post-Fader Metering
Metering
There are two modes for monitoring so that both the input and output signals
can be monitored separately.
Adjusting Output Levels
When set to pre-fader, the meter displays the signal level from the source
on the Dante network. If signals are too low or clipping, adjust them at the
source.
Output Levels
Access the analog output levels through the web application, by selecting
an output level from the Analog Gain (dB) pull-down menu. Match the output
level from the Network Interface to the input sensitivity on the analog device:
When set to post-fader, the meter is affected by the digital gain. It is not affected by the output analog gain setting.
ANI4OUT Command Strings
Command Strings
The device is connected via Ethernet to a control system, such as AMX, Crestron or Extron.
Connection: Ethernet (TCP/IP; select “Client” in the AMX/Crestron program)
Port: 2202
Conventions
The device has 4 types of strings:
GET
Finds the status of a parameter. After the AMX/Crestron sends a GET command, the ANI4OUT responds with a REPORT string
SET
Changes the status of a parameter. After the AMX/Crestron sends a SET command, the ANI4OUT will respond with a REPORT string to indicate the new value
of the parameter.
REP
When the ANI4OUT receives a GET or SET command, it will reply with a REPORT command to indicate the status of the parameter. REPORT is also sent by
the ANI4OUT when a parameter is changed on the ANI4OUT or through the GUI.
SAMPLE
Used for metering audio levels.
All messages sent and received are ASCII. Note that the level indicators and gain indicators are also in ASCII
Most parameters will send a REPORT command when they change. Thus, it is not necessary to constantly query parameters. The ANI4OUT will send a REPORT
command when any of these parameters change.
The character “x” in all of the following strings represents the channel of the ANI4OUT and can be ASCII numbers 0 through 4 as in the following table
0
All channels
1 through 4
Individual channels
Command Strings (Common)
Get All
Command String:
< GET x ALL >
2017/10/30
Where x is ASCII channel number: 0 through 4.
Use this command on first power on to update the
status of all parameters.
17/28
ANI4OUT
Shure Incorporated
ANI4OUT Response:
The ANI4OUT responds with individual Report
strings for all parameters.
< REP ... >
Get Model Number
Command String:
< GET MODEL >
ANI4OUT Response:
< REP MODEL {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy is 32
characters of the model number. The ANI4OUT
always responds with a 32 character model
number.
Get Serial Number
Command String:
< GET SERIAL_NUM >
ANI4OUT Response:
< REP SERIAL_NUM {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy is 32
characters of the serial number. The ANI4OUT
always responds with a 32 character serial number.
Get Firmware Version
Command String:
< GET FW_VER >
ANI4OUT Response:
< REP FW_VER {yyyyyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyyyyy is 18 characters. The
ANI4OUT always responds with 18 characters.
Get Audio IP Address
Command String:
< GET IP_ADDR_NET_AUDIO_PRIMARY >
ANI4OUT Response:
< REP IP_ADDR_NET_AUDIO_PRIMARY {yyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyy is a 15 digit IP address.
Get Audio Subnet Address
Command String:
< GET IP_SUBNET_NET_AUDIO_PRIMARY >
ANI4OUT Response:
< REP IP_SUBNET_NET_AUDIO_PRIMARY {yyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyy is a 15 digit subnet
address.
Get Audio Gateway Address
Command String:
< GET IP_GATEWAY_NET_AUDIO_PRIMARY >
ANI4OUT Response:
< REP IP_GATEWAY_NET_AUDIO_PRIMARY {yyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyy is a 15 digit gateway
address.
Get Channel Name
Command String:
Where x is ASCII channel number: 0 through 4.
< GET x CHAN_NAME
ANI4OUT Response:
< REP x CHAN_NAME {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy is 31
characters of the user name.The ANI4OUT always
responds with a 31 channel name.
Get Device ID
Command String:
The Device ID command does not contain the x
channel character, as it is for the entire ANI4OUT.
< GET DEVICE_ID >
ANI4OUT Response:
< REP DEVICE_ID {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} >
Where yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy is 31
characters of the device ID. The ANI4OUT always
responds with a 31 character device ID.
Get Preset
18/28
2017/10/30
ANI4OUT
Shure Incorporated
Command String:
< GET PRESET >
ANI4OUT Response:
Where nn is the preset number 01-10.
< REP PRESET nn >
Set Preset
Command String:
Where nn is the preset number 1-10. (Leading zero
is optional when using the SET command).
< SET PRESET nn >
ANI4OUT Response:
Where nn is the preset number 01-10.
< REP PRESET nn >
Get Preset Name
Command String:
< GET PRESET1 >
Send one of these commands to the ANI4OUT
< GET PRESET2 >
< GET PRESET3 >
etc
ANI4OUT Response:
< REP PRESET1 {yyyyyyyyyyyyyyyyyyyyyyyyy} >
< REP PRESET2 {yyyyyyyyyyyyyyyyyyyyyyyyy} >
< REP PRESET3 {yyyyyyyyyyyyyyyyyyyyyyyyy} >
Whereyyyyyyyyyyyyyyyyyyyyyyyyy is 25 characters
of the preset name.The ANI4OUT always responds
with a 25 character preset name
etc
Get Audio Gain
Command String:
< GET x AUDIO_GAIN_HI_RES >
ANI4OUT Response:
< REP x AUDIO_GAIN_HI_RES yyyy >
Where x is ASCII channel number: 1 through 4.
Where yyyy takes on the ASCII values of 0000 to
1400. yyyy is in steps of one-tenth of a dB.
Set Audio Gain
Command String:
< SET x AUDIO_GAIN_HI_RES yyyy >
ANI4OUT Response:
< REP x AUDIO_GAIN_HI_RES yyyy >
Where yyyy takes on the ASCII values of 0000 to
1400. yyyy is in steps of one-tenth of a dB.
Where yyyy takes on the ASCII values of 0000 to
1400.
Increase Audio Gain by n dB
Command String:
< SET x AUDIO_GAIN_HI_RES INC nn >
ANI4OUT Response:
< REP x AUDIO_GAIN_HI_RES yyyy >
Where nn is the amount in one-tenth of a dB to
increase the gain. nn can be single digit ( n ),
double digit ( nn ), triple digit ( nnn ).
Where yyyy takes on the ASCII values of 0000 to
1400.
Decrease Audio Gain by n dB
Command String:
< SET x AUDIO_GAIN_HI_RES DEC nn >
ANI4OUT Response:
< REP x AUDIO_GAIN_HI_RES yyyy >
Where nn is the amount in one-tenth of a dB to
decrease the gain. nn can be single digit ( n ),
double digit ( nn ), triple digit ( nnn ).
Where yyyy takes on the ASCII values of 0000 to
1280.
Get Channel Audio Mute
Command String:
< GET x AUDIO_MUTE >
Where x is ASCII channel number: 0 through 4.
ANI4OUT Response:
< REP x AUDIO_MUTE ON >
The ANI4OUT will respond with one of these
strings.
< REP x AUDIO_MUTE OFF >
2017/10/30
19/28
ANI4OUT
Shure Incorporated
Mute Channel Audio
Command String:
< SET x AUDIO_MUTE ON >
ANI4OUT Response:
< REP x AUDIO_MUTE ON >
Unmute Channel Audio
Command String:
< SET x AUDIO_MUTE OFF >
ANI4OUT Response:
< REP x AUDIO_MUTE OFF >
Toggle Channel Audio Mute
Command String:
< SET x AUDIO_MUTE TOGGLE >
ANI4OUT Response:
< REP x AUDIO_MUTE ON >
The ANI4OUT will respond with one of these
strings.
< REP x AUDIO_MUTE OFF >
Get Analog Gain
Command String:
< GET x AUDIO_OUT_LVL_SWITCH >
Where x is ASCII channel number: 0 through 4.
ANI4OUT Response:
< REP x AUDIO_OUT_LVL_SWITCH LINE_LVL >
< REP x AUDIO_OUT_LVL_SWITCH AUX_LVL >
The ANI4OUT will respond with one of these
strings.
< REP x AUDIO_OUT_LVL_SWITCH MIC_LVL >
Set Analog Gain
Command String:
< SET x AUDIO_OUT_LVL_SWITCH LINE_LVL >
< SET x AUDIO_OUT_LVL_SWITCH AUX_LVL >
Where x is ASCII channel number: 0 through 4.
Send one of these commands to the ANI4OUT.
< SET x AUDIO_OUT_LVL_SWITCH MIC_LVL >
ANI4OUT Response:
< REP x AUDIO_OUT_LVL_SWITCH LINE_LVL >
< REP x AUDIO_OUT_LVL_SWITCH AUX_LVL >
The ANI4OUT will respond with one of these
strings.
< REP x AUDIO_OUT_LVL_SWITCH MIC_LVL >
Get Sig/Clip LED
Command String:
< GET x LED_COLOR_SIG_CLIP >
Where x is ASCII channel number: 0 through 4. It
is not necessary to continually send this command.
The ANI4OUT will send a REPORT message
whenever the status changes.
ANI4OUT Response:
< REP x LED_COLOR_SIG_CLIP OFF >
< REP x LED_COLOR_SIG_CLIP GREEN >
< REP x LED_COLOR_SIG_CLIP AMBER >
The ANI4OUT will respond with one of these
strings. This matches the sig/clip LEDs on the front
of the ANI4OUT.
< REP x LED_COLOR_SIG_CLIP RED >
Flash Lights on ANI4OUT
Command String:
< SET FLASH ON >
Send one of these commands to the ANI4OUT.
The flash automatically turns off after 30 seconds.
< SET FLASH OFF >
20/28
2017/10/30
ANI4OUT
Shure Incorporated
ANI4OUT Response:
The ANI4OUT will respond with one of these
strings.
< REP FLASH ON >
< REP FLASH OFF >
Turn Metering On
Where sssss is the metering speed in milliseconds.
Setting sssss=0 turns metering off. Minimum setting
is 100 milliseconds. Metering is off by default.
Command String:
< SET METER_RATE sssss >
Where aaa, bbb, etc is the value of the audio level
received and is 000-060.
ANI4OUT Response:
aaa = output 1
< REP METER_RATE sssss >
< SAMPLE aaa bbb ccc ddd >
bbb = output 2
ccc = output 3
ddd = output 4
Stop Metering
Command String:
A value of 00000 is also acceptable.
< SET METER_RATE 0 >
ANI4OUT Response:
< REP METER_RATE 00000 >
Get LED Brightness
Command String:
< GET LED_BRIGHTNESS >
Where n can take on the following values:
ANI4OUT Response:
< REP LED_BRIGHTNESS n >
0 = LED disabled
1 = LED dim
2 = LED default
Set LED Brightness
Where n can take on the following values:
Command String:
< SET LED_BRIGHTNESS n >
0 = LED disabled
1 = LED dim
2 = LED default
ANI4OUT Response:
< REP LED_BRIGHTNESS n >
Reboot ANI4OUT (firmware > v2.0)
Command String:
< SET REBOOT >
ANI4OUT Response:
The ANI4OUT does not send a response for this
command
Get Error Events (firmware > v2.0)
Command String:
< GET LAST_ERROR_EVENT >
ANI4OUT Response:
< REP LAST_ERROR_EVENT {yyyyy} >
Where yyyy can be up to 128 characters.
Get Output Meter Mode (firmware > v2.0)
Command String:
< GET OUTPUT_METER_MODE >
ANI4OUT Response:
< REP OUTPUT_METER_MODE PRE_FADER >
The ANI4OUT will respond with one of these
strings.
< REP OUTPUT_METER_MODE POST_FADER >
Set Output Meter Mode (firmware > v2.0)
2017/10/30
21/28
ANI4OUT
Shure Incorporated
Command String:
< SET OUTPUT_METER_MODE PRE_FADER >
Send one of these commands to the ANI4OUT.
< SET OUTPUT_METER_MODE POST_FADER >
ANI4OUT Response:
< REP OUTPUT_METER_MODE PRE_FADER >
The ANI4OUT will respond with one of these
strings.
< REP OUTPUT_METER_MODE POST_FADER >
Get Limiter Engaged (firmware > v2.0)
Command String:
< GET x LIMITER_ENGAGED >
Where x is ASCII channel number: 1 or 3. The
limiter is only engaged when using summing mode
ANI4OUT Response:
< REP x LIMITER_ENGAGED ON >
The ANI4OUT will respond with one of these
strings.
< REP x LIMITER_ENGAGED OFF >
Get Audio Summing Mode (firmware > v2.0)
Command String:
< GET AUDIO_SUMMING_MODE >
ANI4OUT Response:
< REP AUDIO_SUMMING_MODE OFF >
< REP AUDIO_SUMMING_MODE 1+2 >
< REP AUDIO_SUMMING_MODE 3+4 >
The ANI4OUT will respond with one of these
strings.
< REP AUDIO_SUMMING_MODE 1+2/3+4 >
< REP AUDIO_SUMMING_MODE 1+2+3+4 >
Set Audio Summing Mode (firmware > v2.0)
Command String:
< SET AUDIO_SUMMING_MODE OFF >
< SET AUDIO_SUMMING_MODE 1+2 >
< SET AUDIO_SUMMING_MODE 3+4 >
Send one of these commands to the ANI4OUT.
< SET AUDIO_SUMMING_MODE 1+2/3+4 >
< SET AUDIO_SUMMING_MODE 1+2+3+4 >
ANI4OUT Response:
< REP AUDIO_SUMMING_MODE OFF >
< REP AUDIO_SUMMING_MODE 1+2 >
< REP AUDIO_SUMMING_MODE 3+4 >
The ANI4OUT will respond with one of these
strings.
< REP AUDIO_SUMMING_MODE 1+2/3+4 >
< REP AUDIO_SUMMING_MODE 1+2+3+4 >
Get RMS Audio Level (firmware > v2.0)
Command String:
< GET x AUDIO_IN_RMS_LVL >
ANI4OUT Response:
< REP x AUDIO_IN_RMS_LVLnnn >
where xis channel number: 0: all channels ANI4IN:
1-4
where x is channel number defined in GET
command. where nnn is audio level in the range of
000-060
Get Peak Audio Level (firmware > v2.0)
Command String:
< GET x AUDIO_IN_PEAK_LVL >
ANI4OUT Response:
< REP x AUDIO_IN_PEAK_LVLnnn >
where xis channel number: 0: all channels ANI4IN:
1-4
where x is channel number defined in GET
command. where nnn is audio level in the range of
000-060
Get Network Audio Device Name
Command String:
< GET NA_DEVICE_NAME >
22/28
2017/10/30
ANI4OUT
Shure Incorporated
ANI4OUT Response:
< REP NA_DEVICE_NAME {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} >
Where {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} is a
text string. Most devices allow device id to be up
to 31characters. Value is padded with spaces as
needed to ensure that 31 char are always reported.
Get Network Audio Channel Name
Command String:
Where xx is channel number All channels: 0
ANI4OUT: 1-4
< GET NA_CHAN_NAME >
ANI4OUT Response:
< REP xx NA_CHAN_NAME {yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy}
Where xx is channel number. Where
{yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy} is 31 char
channel name. Value is padded with spaces as
needed to ensure that 31 char are always reported.
Returns errors per Standardization of Values for
Reporting Error States under any of the following
conditions: Invalid channel
Get Control Network MAC Address
Command String:
< GET CONTROL_MAC_ADDR >
ANI4OUT Response:
< REP CONTROL_ MAC_ADDR yy:yy:yy:yy:yy:yy >
Where yy:yy:yy:yy:yy:yy is a 17 char literal string
formatted as 6 octets, each separated by a colon.
Example: 00:0E:DD:FF:F1:63
Restore Default Settings (firmware > v2.0)
Command String:
Request the device to set itself to default settings.
< SET DEFAULT_SETTINGS >
ANI4OUT Response:
where xx = 00 if restore is successful
< REP PRESET xx >
Get LED State
Command String:
< GET x LED_STATE_SIG_CLIP >
ANI4OUT Response:
< REP x LED_STATE_SIG_CLIP yyy >
where x is channel number that takes on values:
0: all channels 1-4: individual channel
where x is channel number that takes on values:
1-4: individual channel ;Where yyy is current LED
state. Valid yyy values are: On - Steady ,Flashing,
Off
Get PEQ Filter Enable (firmware > v2.0)
Command String:
< GET xx PEQ yy >
Where xx is the PEQ block 01-04. Where yy is the
PEQ filter 01-04 within the block. 00 can be used
for all blocks or all filters.
ANI4OUT Response:
< REP xx PEQ yy ON >
< REP xx PEQ yy OFF >
Set PEQ Filter Enable (firmware > v2.0)
Command String:
< SET xx PEQ yy ON >
Send one of these commands to the ANI4OUT.
< SET xx PEQ yy OFF >
ANI4OUT Response:
< REP xx PEQ yy ON >
< REP xx PEQ yy OFF >
Where xx is the PEQ block 01-04. Where yy is the
PEQ filter 01-04 within the block. 00 can be used
for all blocks or all filters.
Get Encryption Status (firmware > v2.0)
2017/10/30
23/28
ANI4OUT
Shure Incorporated
Command String:
Get device level encryption status;
< GET ENCRYPTION >
ANI4OUT Response:
Send one of these commands to the ANI4OUT.
< REP ENCRYPTION ON >
< REP ENCRYPTION OFF >
網路和 Dante
數字式音訊網路
Dantetm 數字音訊訊號是透過標準乙太網路傳輸的,使用標準的網路通訊協定工作。Dante 具有低延遲、緊密時鐘同步和高品質服務 (QoS) 等功能,從而為各種
Dante 裝置提供可靠的音訊廣播。Dante 音訊可以與 IT 和控制資料在相同網路中安全共存,也可以設定為使用私人網路絡。
適用於 Dante 網路的交換機建議
除了基本聯網要求以外,Dante 音訊網路應使用具有下列功能的千兆乙太網路交換機或路由器:
•
千兆乙太網路埠
•
可容納 4 個佇列的品質服務 (QoS)
•
採用嚴格優先順序的 Diffserv (DSCP) QoS
•
推薦使用:受管理客戶機能夠提供有關每個網路連接的詳細資訊(埠速度、錯誤技術、佔用頻寬)
QoS(服務品質)設定
QoS 設定
QoS 設定可將優先順序分配到網路上的特定資料包,確保流量龐大的較大網路上有可靠的音訊傳輸。此功能可用於大部分受管理的網路開關。雖然並非必要,
但仍建議分配 QoS 設定。
與網路管理員協調變更,避免中斷服務。
若要指定 QoS 值,請開啟開關介面並使用下表指定 Dante™ 相關佇列值。
•
指定關鍵時間 PTP 事件的最高可能值(在此例中顯示為 4)。
•
在每個剩餘的資料包使用遞減優先順序值。
®
由 Audinate
提供的表格
優先順序
使用情況
DSCP 標籤
十六進位
十進位
二進位
高 (4)
關鍵時間 PTP 事件
CS7
0x38
56
111000
中 (3)
音訊、PTP
EF
0x2E
46
101110
低 (2)
(已保留)
CS1
0x08
8
001000
無 (1)
其他流量
BestEffort
0x00
0
000000
不同的製造商和開關類型可能會有不同的開關管理。請查詢製造商的產品指南,瞭解特定設定的詳細資訊。
如需更多關於 Dante 需求和網路的資訊,請至 www.audinate.com。
網路術語
PTP
DSCP
用來同步網路上的時鐘
用於層 3 QoS 優先順序的標準化識別方式
Dante™ Transmit Flows
Dante Flows
This device supports up to two transmit flows and two receive flows. A single flow consists of up to four channels, through either a unicast or multicast
transmission.
•
A unicast flow is a point-to-point connection between two devices, supporting up to four channels per flow.
•
A multicast flow is a one-to-many transmission, which supports sending up to four channels to multiple receiving devices across the network.
Shure Device Applications
This device can connect with up to two Dante devices.
24/28
2017/10/30
ANI4OUT
Shure Incorporated
The Shure MXA310, ANI22, ANIUSB-MATRIX and ANI4IN support multicast transmission. This means that flows can transmit to multiple devices -- as many
as the network can support. If using unicast flows, each of these devices can connect with up to two Dante receiver devices.
The Shure ANI4OUT connects with up to two Dante transmitter devices.
資料包橋接器
資料包橋接器可讓外部控制器從 Shure 裝置的控制介面取得 IP 資訊。若要存取資料包橋接器,外部控制器必須透過
Dante 介面上的 2203。
UDP* 將查詢資料包傳送至 Shure 裝置之
1. 透過至少 1 位元組的酬載傳送 UDP 資料包。
接受的最大酬載為 140 個位元組。任何內容都可被允許。
2. Shure 裝置將會使用與查詢資料包來源連接埠相同的目的地 UDP 連接埠,透過單點傳播 UDP 將回應資料包傳送至控制器。回應資料包的酬載依照此格式:
位元組
內容
0-3
IP 位址,即按照網路順序的 32 位元無符號整數
4-7
子網路遮罩,即按照網路順序的 32 位元無符號整數
8-13
MAC 位址,即 6 位元組的陣列
在一般網路上,Shure 裝置應於一秒之內回應。若沒有回應,請在驗證目的地 IP 位址和連接埠號後,嘗試再次傳送查詢。
*UDP 使用者資料包通訊協定
重要產品資訊
此設備用於專業音響場合。
不能將本設備直接連接到公眾互聯網。
EMC 符合環境 E2:商業和輕工業。測試是使用所提供和推薦的纜線類型完
成的。使用其它無遮罩的纜線類型可能會降低 EMC 效能。
未經舒爾公司明確許可的修改或改裝會使您操作本設備的授權失效。
ICES-003
CAN ICES-3 (B)/NMB-3(B)
符合美國聯邦通訊委員會法規第 15B 章:
請遵循您所在地的電池、包裝和電子廢棄物回收標準。
用戶資訊
本設備已經過測試,符合 FCC 法規第 15 章有關 B 類數位設備的限制。這些
限制專適用於在住宅內安裝此設備,能夠為用戶提供免受有害幹擾影響的足
夠保護。本設備產生、使用並可能發射無線電頻率能量,如果沒有按照要求
安裝和使用設備,可能會對無線電通訊產生有害幹擾。但是,並不保證本設
備在特定的安裝情況下不產生幹擾。如果本設備確實對收音機或電視機的接
收產生有害幹擾,可以通過關閉本設備然後再打開的方法來確定幹擾,建議
用戶通過以下一種或多種方法自行排除此幹擾。
•
調整接收天線的方向或位置。
•
增大設備和接收機之間的距離。
•
將設備連接到與接收機不同的電路插座。
•
可以向經銷商或有經驗的無線電/電視工程師咨詢以尋求幫助。
可從以下地址獲得“CE 符合性聲明”:www.shure.com/europe/compliance
歐盟授權代表:
Shure Europe GmbH
歐洲、中東、非洲總部
部門:歐洲、中東、非洲批准部
Jakob-Dieffenbacher-Str.12
75031 Eppingen, Germany
電話:+49-7262-92 49 0
傳真:+49-7262-92 49 11 4
電子郵件:info@shure.de
本產品符合所有相關歐盟法規的基本要求,並且允許使用 CE 標誌。
可從舒爾公司或其任何歐洲代表處獲得“歐盟符合性聲明”。 有關聯繫資訊,
請存取 www.shure.com
規格
輸入
(1) RJ45
輸出
ANI4OUT-XLR
(4) XLR 接頭
ANI4OUT-BLOCK
(4) 3 腳塊連接器
設定
平衡阻抗
極性
非倒相,任何輸入至任何輸出
2017/10/30
25/28
ANI4OUT
Shure Incorporated
電源要求
乙太網供電 (PoE), 0 類
功率消耗
10W, 最大值
重量
663 克 (1.5 磅)
外觀尺寸
高度 x 寬度 x 深度
4 x 14 x 12.8 釐米 (1.6 x 5.5 x 5.0 英寸)
控制應用程式
HTML5 基於瀏覽器
工作溫度範圍
−6.7°C (20°F) 到 40°C (104°F)
存儲溫度範圍
−29°C (-20°F) 到 74°C (165°F)
音訊
頻率響應
20 到 20,000 赫茲
輸入 (Dante 數位音訊)
頻道數
4
採樣率
48 千赫
位深度
24
Line(線路)
+20 dBV
Aux(輔助)
+0 dBV
話筒
-26 dBV
延遲
Does not include Dante latency
0.71 毫秒
動態範圍 (Dante 至類比)
20 赫茲至 20 千赫, A-加權, 典型
117 dB
總諧波失真
@ 1 千赫, -20 dBFS 輸出, 0 dB 類比增益
<0.05%
輸出 削波電平
類比輸出電平
可選擇
26/28
Line(線路)
0 dB
Aux(輔助)
- 20 dB
話筒
-46 dB
2017/10/30
ANI4OUT
Shure Incorporated
輸出阻抗
150 Ω
內置 數字訊號處理
每頻道
等化器 (4 波段參數), 靜音, Invert Polarity, 增益位置 (140 dB 範圍)
系統
音訊相加
連網
纜線要求
Cat 5e 或更高規格 (建議採用遮罩線)
IP 埠和協議
埠
TCP/UDP
協議
說明
工廠預設值
21
tcp
FTP
固件更新需要(否則關閉)
已關閉
22
tcp
SSH
不支援
已關閉
23
tcp
Telnet
標準控制台介面
已關閉
68
udp
DHCP
動態主機設定通訊協定
開啟
80*
tcp
HTTP
需要啟動嵌入式網頁伺服器
開啟
427
tcp/udp
SLP†
裝置間通訊需要
開啟
443
tcp
HTTPS
不支援
已關閉
161
tcp
SNMP
不支援
已關閉
162
tcp
SNMP
不支援
已關閉
2202
tcp
ASCII
協力廠商控制字串需要
開啟
5353
udp
mDNS†
裝置發現需要
開啟
5568
udp
SDT†
裝置間通訊需要
開啟
8023
tcp
Telnet
調試控制台介面
密碼
8180*
tcp
HTML
需要用於 網頁應用程式
開啟
8427
udp
多播 SLP†
裝置間通訊需要
開啟
64000
tcp
Telnet
Shure 固件升級需要
開啟
埠
TCP/UDP
協議
說明
162
udp
SNMP
供 Dante 使用
[319-320]*
udp
PTP†
Dante 時鐘
2203
udp
Custom(定制)
需要用於資料包橋接器
4321,
14336-14600
udp
Dante
Dante 音訊
[4440, 4444,
4455]*
udp
Dante
Dante 音訊路由
5353
udp
mDNS†
供 Dante 使用
[8700-8706,
8800]*
udp
Dante
Dante 控制和監控
8751
udp
Dante
Dante 控制器
16000-65536
udp
Dante
供 Dante 使用
01
0
*只有在 PC 或控制系統上開啟這些埠才能透過防火牆存取裝置。
1
†這些通訊協定需要多點傳播。確保您的網路已正確設定多播。
2017/10/30
27/28
ANI4OUT
Shure Incorporated
附件
提供的附件
硬體套件(XLR 型號)
90A29254
硬體套件(塊連接器型號)
90A29252
安裝支架(1/3 機架單元)
53A27742
選配附件和替換部件
19 英寸機架托盤
CRT1
Shure Incorporated 5800 West Touhy Avenue Niles, IL 60714-4608 USA Phone: +1-847-600-2000 Email: info@shure.com
28/28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising