Bunn | FMD-5 | Service manual | BUNN FMD-5 Fresh Mix Dispenser Service Manual

BUNN FMD-5 Fresh Mix Dispenser Service Manual
FMD Series
Including: FMD-1,2,3,4,5
SERVICE & REPAIR MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
42672.0000C 04/17 ©2009 Bunn-O-Matic Corporation
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCR/MCP/MCA single cup brewers, thermal servers and ThermoFresh® servers (mechanical and digital) 1 year parts and 1 year labor.
2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:
a) Electronic circuit and/or control boards - parts and labor for 3 years.
b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.
c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and
labor for 4 years or 40,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be
commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the
applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured
by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation,
improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality,
damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but
not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN
prompt notice of
any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box
3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized
BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make
modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such
individuals, whether oral or written, do not constitute warranties and should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the
applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair
is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for
the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS
EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION
AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of
use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities
or services, or any other special, incidental or consequential damages.
392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with
the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design,
Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet
Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment
Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com,
Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in
Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, TRIFECTA (sylized logo), Velocity Brew, Air Brew, Beverage
Bar Creator, Beverage Profit Calculator, Brew better, not bitter., Build-A-Drink, BUNNSource, Coffee At Its Best, Cyclonic
Heating System, Daypart, Digital Brewer Control, Element, Milk Texturing Fusion, Nothing Brews Like a BUNN, Picture
Prompted Cleaning, Pouring Profits, Signature Series, Sure Tamp, Tea At Its Best, The Horizontal Red Line, Ultra are either
trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing configuration is a trademark of Bunn-O-Matic Corporation.
2
42672 031314
INTRODUCTION
Safety first!
To avoid electrical shock, unplug dispenser from power source before servicing inside.
Basic Maintenance
In order to maintain proper machine operation, a Preventative Maintenance schedule must be performed on a
regular basis.
The following procedures pretain to all versions in the FMD family of machines unless otherwise noted.
CONTENTS
Warranty....................................................................................................................................2
User Notices..............................................................................................................................3
Site Preparation ........................................................................................................................3
Preventive Maintenance
Recommended Cleaning .....................................................................................................4
Preventive Maintenance Schedule........................................................................................5
Troubleshooting.........................................................................................................................6
Service.....................................................................................................................................12
Electrical Schematics...............................................................................................................42
USER NOTICES
All notices on this equipment are written for your protection. All notices are to be kept in good condition.
Replace any unreadable or damaged labels.
SITE PREPARATION
A minimal clearance is required between the dispenser sides and the wall or another appliances. Leave some
space so the dispenser can be moved for cleaning.
3
42672 122209
CLEANING
The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device.
1 x 24h
1. Rinse out Whipper Chambers by placing RINSE/RUN
switch in the "RINSE" position and activating DISPENSE
switches.
2. Turn elbow up, remove Hoppers, refill with product and
replace hoppers into dispenser.
3. Empty Drip Tray and wash in a solution of dish detergent.
7
1. Para limpiar las camaras de mezcla, coloque el interruptor en la
posicón ENJUAGUE/MARCHA (”RINSE/RUN”) y pulse el boton
para espumar y distribuir la bebida (”DISPENSE”).
2. Gire el codo hacia arriba, remueva las tolvas, llene las tolvas con
producto y coloque las tolvas nuevamente en la maquina.
3. Vacie la bandeja de goteo y limpiela con un detergente liquido
suave no abrasivo.
1 x 7d
9
1
6
2
8
7
5
3
4
a. Wash
b. Rinse
c. Sanitize
d. Dry
a
b
a. Lave
b. Enjuague
c. Desinfecte
d. Seque
Replace Light Bulbs
as required.
Cambie los bombillos
quemados cuando
sea necesario.
c
NOTICE
The cleaning instructions noted above are for non-dairy sugar based food products. When dispensing any other food product,
the cleaning cycle for the whipping chamber assembly and ejector elbow must be performed daily.
NOTA:
Las instrucciones de limpieza descritas anteriormente excluyen productos lacteos azucarados. La limpieza de las camaras
de mezcla y de los codos de salida de cada tolva deberá realizarse diariamente.
37254.0000A 07/04 © 2004 BUNN-O-MATIC CORPORATION
4
42672 122209
REQUIRED REGULAR MAINTENANCE:
When performing Daily-Weekly Cleaning procedures, inspect o-rings, seals, and bushings for signs of wear or
damage and replace immediately.
Check and/or replace every 6 months or as required:
32906.0000
Mixing Chamber Kit (Includes items indented below)
25732.0000Steam Collector
25733.0000Mixing Chamber
25734.0000Whipper Chamber
25736.0000Dispense Tip
24733.0010O-ring
25902.0000Frother
26356.0000Shaft Seal
28866.0000Receptacle
25903.0000Elbow
29128.0000
Whipper Motor Seal Kit (Includes items indented below)
24733.0010O-ring
28867.0000Slinger
26356.0000Shaft Seal
Check and/or replace every 3 months or as required:
26356.1000
Whipper Shaft Seal Kit (Contains 6 Seals)
5
42672 122209
TROUBLESHOOTING
A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems
encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic
Technical Service Department.
•
•
•
•
•
•
•
Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel.
All electronic components have high voltage ac and low voltage dc potential on their terminals. Shorting of
terminals or the application of external voltages may result in board failure.
Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If
an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a
terminal or crimp.
Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are
energized for more than ten minutes without a supply of water.
The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will
help to avoid twists and kinks in the tubing.
Make certain that all plumbing connections are sealed and electrical connections tight and isolated.
This unit is heated at all times. Keep away from combustibles.
WARNING –
•
•
•
•
Exercise extreme caution when servicing electrical equipment.
Unplug the dispenser when servicing, except when electrical tests are specified.
Follow recommended service procedures
Replace all protective shields or safety notices
PROBLEM
PROBABLE CAUSE
REMEDY
Product will not dispense
1. No water
Water lines and valves to the dispenser must be open.
2. No power or incorrect voltage to (A) Check for correct voltage to the
the dispenser
dispenser.
(B) Check circuit breakers or fuses.
3. Dispense Switch
Refer to Service - Dispense Switch for
testing procedure. See page 28
4. Digital Touch Control Switch
Refer to Service - Digital Touch
Control Switch for testing procedure.
See page 29
5. Dispense Solenoid Valve
Refer to Service - Dispense Solenoid
Valve for testing procedures. See
page 47
6. Solenoid Valve (Inlet)
Refer to Service - Solenoid Valve
(Inlet) for testing procedures. See
page 49
6
42672 122209
TROUBLESHOOTING (cont.)
PROBLEM
Product will not dispense (cont.)
PROBABLE CAUSE
REMEDY
7. Level Control Board and Probe - Refer to Service - Level Control Board
FMD-1
and Probe for testing procedures.
See page 41
8. Control Board
Refer to Service - Control Board and
Probe for testing procedures. See
page 20
9. Overflow Protection Switch
Refer to Service - Overflow Protection Switch. See page 44
10. Auger Drive
Refer to Service - Auger Drive. See
page 14
11. Water Strainer
(A) Direction of flow arrow must be
pointing towards dispenser.
(B) Remove the strainer and check for
obstructions. Clear or replace.
12. Lime build-up
Inspect the tank assembly for exCAUTION - Tank and tank compo- cessive lime deposits. Delime as
nents should be delimed regularly required.
depending on local water conditions.
Excessive mineral build-up on stainless steel surfaces can initiate corrosive reactions resulting in serious
leaks.
Water is not hot
13. Transformer
Refer to Service - Transformer for
testing procedures. See page 40
14. Rinse Cycle Not Run
Refer to Cleaning for running a Rinse
Cycle.
1. Limit Thermostat
Refer to Service - Limit Thermostat
CAUTION - Do not eliminate or by- for testing procedures. See page
pass limit thermostat. Use only BOM 43
replacement part #29329.1000
2. Control Thermostat
Refer to Service - Control Thermostat
for testing procedures. See page
26
3. Tank Heater
Refer to Service - Tank Heater for
testing procedures. See page 50
7
42672 122209
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Water is not hot (Cont.)
4. Tank Heater Switch
Refer to Service - Tank Heater Switch
for testing procedures. See page
52
5. Heater Relay
Refer to Service - Heater Relay for
testing procedures. See page 51
6. Control Board
Refer to Service - Control Board for
testing procedures. See page 20
Spitting or excessive steaming
1. Lime build-up
Inspect the tank assembly for exCAUTION - Tank and tank compo- cessive lime deposits. Delime as
nents should be delimed regularly required.
depending on local water conditions.
Excessive mineral build-up on stainless steel surfaces can initiate corrosive reactions resulting in serious
leaks.
2. Control Thermostat
Dripping from dispense tip
Water flows into tank continuously
Refer to Service - Control Thermostat for testing procedures. See
page 26
1. Lime build-up
Inspect the tank assembly for exCAUTION - Tank and tank compo- cessive lime deposits. Delime as
nents should be delimed regularly required.
depending on local water conditions.
Excessive mineral build-up on stainless steel surfaces can initiate corrosive reactions resulting in serious
leaks.
2. Dispense Solenoid Valve
Remove the dispense solenoid valve
and clear any obstructions. Rebuild
or replace the valve if necessary. See
page 47
1. Control Board
Refer to Service - Control Board and
Probe for testing procedures. See
page 20
2. Solenoid Valve (Inlet)
Refer to Service - Solenoid Valve
(Inlet) for testing procedures. See
page 49
8
42672 122209
TROUBLESHOOTING (cont.)
PROBLEM
Water flows into tank continuously
(Cont.)
Weak product
PROBABLE CAUSE
REMEDY
3. Overflow Protection Switch
Refer to Service - Overflow Protection Switch. See page 44
4. Digital Touch Control Switch
Refer to Service - Digital Touch Control Switch for testing procedures.
See page 29
1. Water Temperature
Place an empty container beneath the
dispense tip. Initiate a dispense cycle
and check the water temperature
immediately below the dispense tip
with a thermometer.(see thermostat
temperature settings decal)
2. Whipper Motor
Refer to Service - Whipper Motor for
testing procedure. See page 34
3. Frother
Refer to Service - Frother Components. See page 33
4. Dispense Solenoid Valve
Refer to Service - Dispense Solenoid
for test procedures. See page 47
5. Auger Drive
Refer to Service - Auger Drive Components. See page 14
6. Auger Spring
Refer to Service - Auger Drive Components. See page 14
7. Auger Motor
Refer to Service - Auger Drive Components. See page 14
8. Rinse/Run Switch
Refer to Service - Rinse/Run Switch
for test procedures. See page 45
9. Rinse Timer
Refer to the Installation and Operating Manual
10. Tank Heater Relay
Refer to Service - Relay. See page
51
11. Control Board
Refer to Service - Control Board. See
page 20
9
42672 122209
TROUBLESHOOTING (CONT.)
PROBLEM
PROBABLE CAUSE
REMEDY
Product overflows container
1. Dispense Switch
Refer to Service - Dispense Switch for
testing procedures. See page 28
2. Dispense Solenoid Valve
Remove the solenoid valve and clear
any obstructions. Rebuild or replace
the valve if necessary. See page 47
1. Plumbing Lines
Plumbing lines should not be resting
on the counter top.
2. Water Supply
(A) The dispenser can be connected
to a cold or hot water line.
Dispenser is making unusual
noises
(B) Water pressure to the dispenser
must not exceed 90 psi (620 kPa).
Install a regulator if necessary to
lower the working pressure to approximately 50 psi (345 kPa).
Excess dust
3. Tank Heater
Remove and clean lime off the tank
heater. See page 50
1. Fan
Refer to Service - Fan for testing
procedures. See page 32
2. A) Hopper Drive Board - FMD-1
Refer to Service - Hopper Drive
Board for testing procedures. See
page 35
B) Control board
Display not lit
Refer to Service - Control Board for
testing procedures. See page 20
1. Lamp
Refer to Service - Lamp, see page
39 for lamp replacement.
2. Lamp Holder
Refer to Service - Lamp Holder for
testing procedures. See page 39
3. Starter - Lamp
Refer to Service - Starter for testing
procedures. See page 40
4. Ballast
Refer to Service - Ballast for testing
procedures. See page 19
10
42672 042417
NOTES
11
42672 122209
SERVICE
This section provides procedures for testing and replacing various major components used in this dispenser
should service become necessary. Refer to Troubleshooting for assistance in determining the cause of any
problem.
WARNING - Inspection, testing, and repair of electrical equipment should be performed only by qualified service
personnel. The dispenser should be disconnected from the power source when servicing, except when electrical
tests are required and the test procedure specifically states to connect the dispenser to the power source.
COMPONENT ACCESS
WARNING - Disconnect the dispenser from the power source before the removal of any panel or the replacement
of any component.
All components are accessible by opening the door, removal of the door panels, dispenser top covers,
hopper(s), hopper support plate, splash guard, splash panel w/drip tray, lower front access panel and rear access cover.
Refer to the contents listing for component location.
INDEX
Access Panels...................................................................................................................................13
Auger Drive Components..................................................................................................................14
Auxillary Control Board (FMD DBC-3)...............................................................................................17
Ballast...............................................................................................................................................19
Control Board (Main)...................................................................................................................20,23
Control Thermostat...........................................................................................................................26
Dispense Switches............................................................................................................................28
Digital Touch Control Switch.............................................................................................................29
EMI Filter (FMD DBC-3)....................................................................................................................31
Fan....................................................................................................................................................32
Frother .............................................................................................................................................33
Hopper Drive Board (FMD-1)............................................................................................................35
Hot/Cold Switch (FMD DBC-3)..........................................................................................................37
Increase/Decrease Switch.................................................................................................................38
Lamp.................................................................................................................................................39
Lamp Holder.....................................................................................................................................39
Lamp Starter & Socket......................................................................................................................40
Level Control Board (FMD-1)............................................................................................................41
Limit Thermostat...............................................................................................................................43
Overflow Protection Switch...............................................................................................................44
Rinse/Run Switch.............................................................................................................................45
Solenoid (Cold Drink)........................................................................................................................46
Solenoid (Dispense)..........................................................................................................................47
Solenoid (Hot Water)........................................................................................................................48
Solenoid (Inlet).................................................................................................................................49
Tank Heater.......................................................................................................................................50
Tank Heater Relay (FMD-4,5)............................................................................................................51
Tank Heater Switch...........................................................................................................................52
Transformer......................................................................................................................................53
Whipper Motor..................................................................................................................................34
12
42672 122209
SERVICE(CONT.)
ACCESS PANELS
Location:
All access panels are similar through the whole FMD family (FMD-5 shown). Before removing panels, make
sure power is OFF to the machine and water is disconnected accept where indicated in testing procedures. Retain
all screws and other attaching hardware for re-assembly.
FMD-5 shown
E
AC E
PL HER
P
CU
FIG. 1 ACCESS PANELS
13
42672 122209
SERVICE (CONT.)
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
AUGER DRIVE COMPONENTS (all Models)
FMD-4 shown
5. Check the voltage across the positive (red wire)
terminal and the negative (black wire) terminal on
the auger motor with a voltmeter. With the rinse/
run switch in the run (lower) position press and
hold the dispense switch. Connect the dispenser
to the power supply. After a .6 second delay the
indication must be 4.0 to 24.5 volts dc.
If voltage is present as described, the auger motor drive
is operating properly. If auger does not turn, replace
the auger motor.
If voltage is not present as described, check the auger
hopper drive board.
J1
J2
J4
Removal, Cleaning and Replacement
Hopper & Auger (FMD-1,4)
1. Open the dispenser door and raise the top front
cover.
2. Lift the hopper assy (15) over the pins on hopper
support plate (11) and slide hopper assembly out
the front of the dispenser.
3. Remove hopper lid (1) and empty product.
4. Pull off the ejector elbow (14).
5. Remove retainer clip (10) and washer (9) from the
bottom of the hopper base (8).
6. Remove whipper shaft (3), wiper blade (4) and
wiper drive gear (5) from the hopper base (8).
7. Remove auger wire (13) by pulling it out the front
of the hopper base (8).
8. Remove auger drive bracket (6) by unscrewing left
hand threads from auger drive shaft (12).
9. Slide spacer (7) and auger drive shaft bracket (6)
off of the auger drive shaft (12).
10. Remove auger drive shaft (12) from hopper base
(8).
11. Wash components in a mild solution of dish detergent using a bristle brush when needed.
12. Rinse and dry each item thoroughly.
13. Check for damaged or broken components, replace
any if necessary and reassemble hopper assembly.
14. Install hopper assy (15) in the dispenser by sliding
hopper assy on the hopper support plate (11) until
the slot in the rear of the hopper base (8) seats
against the pins in the hopper support plate (11).
J3
J1
J2
J4
J3
P4095
FIG. 2 AUGER DRIVE COMPONENTS
Location
The auger components are located inside the bottom
part of the hopper except for the auger drive bracket,
spacer and retaining clip, which are located on the
outside rear of the hopper base. The auger motor is
located on the lower right rear of the motor mounting
panel. Refer to Fig. 3 for disassembly and assembly.
Test Procedures - Auger Motor
1. Disconnect the dispenser from the power source.
2. Disconnect the white/red wire and the white wire
from the hopper drive board (FMD-1) or relative
wires from the control board(all other models).
3. Check the voltage across the white/red wire and
the white wire with a voltmeter. With the rinse/
run switch in the run (lower) position, connect the
dispenser to the power supply. The indication must
be:
a) 120 volts ac for two wire 120 volt models.
b)120 volts ac for three wire120/208 volt or
120/240 volt models.
c) 230 volts ac for two wire 230 volt models.
4. Disconnect the dispenser from the power supply.
14
42672 122209
SERVICE (CONT.)
Auger Drive Motor (Refer to Fig. 2)
1. Remove hopper assy (15), and set aside for reassembly.
2. Remove the four #8-32 screws securing the hopper
support plate (11), remove plate and set aside for
reassembly.
3. Remove the four #8-32 screws, located inside the
dispenser housing on the lower right front of the
auger motor mounting panel (19), securing auger
motor mounting bracket (16) and auger motor
(17) to the rear of the auger motor mounting panel
(19).
4. Disconnect the wires from the hopper drive
board.
5. Remove auger motor mounting bracket (16), auger
motor (17) and dust seal (18) as an assembly.
6. Remove dust seal (18) from auger motor (17).
7. Disconnect the wires from the auger motor (17).
8. Remove the four #8-32 screws securing the auger
motor (17) to the auger motor mounting bracket
(16).
9. Remove auger motor (17) and discard.
10. Using four #8-32 screws install new auger motor
(17) on mounting bracket (16).
11. Install dust seal (18) on auger motor shaft and align
notch in seal with motor casting.
12. Reconnect the wires to the terminals on the hopper
drive board.
13. Refer to schematic wiring diagrams when reconnecting the wires.
14. Using four #8-32 locking screws install auger motor, dust seal and mounting bracket to the rear of
the auger motor mounting panel (19).
15. Install hopper assy (15).
AUGER DRIVE COMPONENTS
FMD-4 shown
1
2
3
4
5
12
13
14
6
7
8
9
10
15
16 17 18 19 11
P2633
FIG. 3 AUGER DRIVE & HOPPER DISASSEMBLY
1. Hopper Lid
2. Hopper
3. Wiper Shaft
4. Wiper Blade
5. Wiper Drive Gear
6. Auger Drive Bracket
7. Spacer
8. Hopper Base
9. Washer
10. Retainer Clip
11.
12.
13.
14.
15.
16.
17.
18.
19.
Hopper Support Plate
Auger Drive Shaft
Auger Wire
Ejector Elbow
Hopper Assembly
Auger Motor Bracket
Auger Motor
Dust Seal
Auger Motor Mounting
panel
RED to Control Board
BLK to GRN from
Control Board
FIG. 4 AUGER MOTOR TERMINALS
15
P1639
42672 122209
SERVICE (CONT.)
AUGER DRIVE COMPONENTS
Removal, Cleaning and Replacement
Hopper & Auger (all other hoppers)
1. Open the dispenser door and raise the top front
cover.
2. Lift the front edge of hopper assy (20) over the
tab on hopper support plate (19) and slide hopper
assembly out the front of the dispenser.
3. Remove hopper lid (1) and empty product.
4. Pull off the ejector elbow (13).
5. Remove agitator disc assy (2) by pulling agitator
support rod (4) towards agitator disc assy and
lifting agitator disc assy from hopper (10).
6. Remove auger (12) by pulling it out the front of
the hopper (10).
7. Remove auger drive shaft (5) by removing the
retaining clip (6) from auger drive shaft.
8. Slide washer (8) and auger drive shaft bracket (7)
off of the auger drive shaft (5).
9. Slide auger drive shaft (5) from auger drive shaft
bushing (3) and remove from hopper (10).
10. Remove locknut (9) from auger drive shaft bushing
(3) and remove auger drive shaft bushing from
hopper (10).
11. Wash components in a mild solution of dish detergent using a bristle brush when needed.
12. Rinse and dry each item thoroughly.
13. Check for damaged or broken components, replace
any if necessary and reassemble hopper assy.
14. Install hopper assy (20) in the dispenser by sliding
hopper assy in the guides on the hopper support
plate (19) until the slot in the bottom rear the hopper seats against the pin (18) in the hopper support
plate.
FMD-5 shown
1
2
4
3
8
5
7
9
10
6
11
14 15 16 12 13
P2634
FIG. 5 AUGER DRIVE & HOPPER DISASSEMBLY
1.
2.
3.
4.
5.
6.
7.
8.
16
Hopper Lid
Mixing Blade
Agitator Disk
Auger Drive Shaft Bushing
Auger Drive Shaft
Locknut
Auger Drive Bracket
Hopper
9. Auger Wire
10. Ejector Elbow
11. Hopper Assy
12. Auger Motor Mounting
Panel
13. Hopper Support Plate
14. Auger Motor Bracket
15. Auger Motor
16. Dust Seal
42672 122209
SERVICE (CONT.)
AUXILLARY CONTROL BOARD (FMD DBC-3 only)
4. Back probe check the voltage across pins 2 (black
wire) and 5 (white wire) of the six pin J2 connector
on the wiring harness with a voltmeter. Connect the
dispenser to the power source. The indication must
be:
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 or 120/240
volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
5. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 6. If
voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
6. Check the voltage across the terminals of the hot
water dispense solenoid with a voltmeter. Connect
the dispenser to the power source. Press the hot
water dispense switch. The indication must be:
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 or 120/240
volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
7. Disconnect the dispenser from the power source.
P4102.40
FIG. 6 AUXILIARY CONTROL BOARD
Location:
The auxiliary control board is located behind the lower
front access cover, mounted on the rear side of the
component bracket.
If voltage is present as described the hot water dispense
circuitry is operating properly. If voltage is not present
as described, replace the auxiliary control board.
Hot Water Dispense
Test Procedure:
1. Disconnect the dispenser from the power source.
2. With a voltmeter, and using the component mounting bracket as a reference (-), back probe check
for voltage at pin 1 (red wire) of J1. Connect the
dispenser to the power source. The indication must
be approximately 37 volts dc.
3. Disconnect the dispenser from the power source.
Ready Light Circuit
Test Procedure:
1. Disconnect the dispenser from the power source.
2. With a voltmeter, and using the component mounting bracket as a reference (-), back probe check
for voltage at pin 1 (red wire) of J1. Connect the
dispenser to the power source. The indication must
be approximately 37 volts dc.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 5. If
voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
If voltage is present as described, proceed to step 4. If
voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
17
42672 122209
SERVICE (CONT.)
AUXILLARY CONTROL BOARD (CONT.)
Removal and Replacement:
1. Loosen the two #8-32 screws securing the component mounting bracket to the dispenser housing.
2. Slide the component mounting bracket forward until
the screw heads align with the large diameters of
the keyhole openings.
3. Lift the component mounting bracket, and pull it
through the lower access panel opening.
4. Disconnect the two plugs on the main wiring harness from the connectors on the auxiliary control
board.
5. Remove the two #6-32 keps nuts securing the
auxiliary control board to the component mounting
bracket.
6. Remove the auxiliary control board.
7. Remove the two snap-in stand-offs from the auxiliary
control board and install them in the new auxiliary
control board. Discard the old auxiliary control
board.
8. Install the new auxiliary control board using the
two #6-32 keps nuts.
9. Reconnect the two plugs on the main wiring harness
to the connectors on the auxiliary control board.
10. Replace the component mounting bracket and
tighten the two #8-32 screws.
4. On the dispenser whipper panel, ensure that the tank
heater switch is in the “ON” (lower) position.
5. Disconnect the black wire coming from the control
thermostat from the limit thermostat.
6. Remove the control thermostat bulb from the
tank.
7. With a voltmeter, and using pin 5 as a reference,
back probe check for voltage, in turn, at pin 3 and
pin 6 of the six pin J2 connector of the wiring harness. Connect the dispenser to the power source.
The indication must be :
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 or 120/240
volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
8. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 9. If
voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
9. Re-install the control thermostat bulb.
10. Noting the starting position of the control thermostat
knob, adjust the control thermostat knob counterclockwise until a click is heard.
11. With a voltmeter, check for voltage between pins 3
and 6 of the six pin J2 connector of the wiring harness. Connect the dispenser to the power source.
The indication must be:
a) 120 volts ac for two wire 120 volt models
b) 208 volts ac for three wire 120/208 or 240 volts
ac for three wire 120/240 volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
12. Disconnect the dispenser from the power source.
Return the control thermostat knob to the starting
position.
J2
J1
If voltage is present as described, replace the auxiliary
control board. If voltage is not present as described,
refer to the wiring diagram and check the dispenser
wiring harness.
FIG. 7 AUXILIARY CONTROL
BOARD TERMINALS
18
P1996.80
42672 122209
SERVICE (cont.)
BALLAST (all Models)
FMD-4 shown
Removal and Replacement
1. Loosen the three #8-32 screws securing the component bracket to the dispenser housing base.
2. Pull component bracket out the front of the dispenser far enough so the leads on each ballast can
be disconnected from the main wiring harness and
the door interconnect harness.
3. Remove the two #8-32 screws securing each ballast
to the rear of the component bracket.
4. Remove and discard the ballast.
5. Install new ballast on the rear of the component
bracket and secure each with two #8-32 screws.
6. Refer to schematic wiring diagrams when reconnecting the wires.
7. Place the component bracket into position and
tighten the two #8-32 screws securing the component bracket to the dispenser housing base.
J1
J2
J4
J3
J1
J2
J4
J3
BLK to BLK
from Main
Wiring Harness
P4095
FIG. 8 BALLASTS
Location
The front door lamp ballasts are located behind
the front access panel and may be on either side of the
component bracket assembly.
BLK to RED from
Main Harness
FIG. 9 BALLAST TERMINALS
P1447
Test Procedure
1. Disconnect the dispenser from the power source.
2. Disconnect the two black leads on the ballast from
the main harness.
3. Check for continuity between the two black leads
on the ballast.
If continuity is present as described the ballast is operating properly.
If continuity is not present as described, replace the
ballast.
19
42672 122209
SERVICE (cont.)
CONTROL BOARD (FMD-2,-2FD,DBC-2FD,DBC-3)
4. With a voltmeter, back probe check the voltage
across pins 2 & 4 of the six pin J2 connector on
the wiring harness. Connect the dispenser to the
power source. The indication must be:
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 volt models
or three wire 120/240 volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
5. Disconnect the dispenser from the power source.
FMD DBC-3 shown
If voltage is present as described, proceed to step 6.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness back
to the power cord.
FIG. 10 CONTROL BOARD
Liquid Level Control Circuitry
6. Carefully connect a piece of insulated jumper wire
to pin 3 (third from left on top row) of J1 on the
control board. Keep the other end of this wire away
from any metal surfaces of the dispenser.
7. With a voltmeter check the voltage across the
terminals of the inlet solenoid valve. Connect the
dispenser to the power source. After a 10 second
delay, the indication must be :
a) 120 volts ac for two wire 120 volt models.
b) 120 volts ac for three wire 120/208 or 120/240
volt models.
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
8. Touch the free end of the jumper wire to the dispenser housing. The indication must be 0.
P4102.40
Location:
The Control Board is located behind the lower front
access cover mounted on the component bracket.
Test Procedure:
Power Supply:
1. Disconnect the dispenser from the power source.
2. With a voltmeter, back probe check the voltage
across pins 1 & 2 of the eight pin J1 connector
on the wiring harness. Connect the dispenser to
the power source. The indication must be 24 volts
ac.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 9.
If the voltage is not present as described, replace the
control circuit board.
NOTE: Verify the ground wire is connected to the board
mounting stud before replacing the control board.
If voltage is present as described, proceed to step 4.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness back
to the transformer.
9. Gently pull the liquid level probe out of the tank lid
and inspect for corrosion. Replace it if necessary.
10. Place the probe so that neither end is in contact
with any metal surface of the dispenser.
20
42672 122209
SERVICE (cont.)
CONTROL BOARD (CONT.)
11. With a voltmeter check the voltage across the
terminals of the inlet solenoid valve. Connect the
dispenser to the power source. After a 10 second
delay, the indication must be :
a) 120 volts ac for two wire 120 volt models.
b) 120 volts ac for three wire 120/208 or 120/240
volt models.
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
12. Move the probe’s flat end to the dispenser housing.
The indication must be 0.
13. Move the probe’s flat end away from the housing.
After a 5 second delay, the indication must, again,
be:
a) 120 volts ac for two wire 120 volt models.
b) 120 volts ac for three wire 120/208 or 120/240
volt models.
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
14. Disconnect the dispenser from the power source.
5. With a voltmeter check the voltage across the red
(+) terminal and the black (-) terminal of the auger
motor. Connect the dispenser to the power source.
Press the appropriate dispense switch. After a
delay of about .6 seconds, the indication must be
between +4.0 and +24.5 volts dc.
If the voltage is present as described, the hopper motor
control circuitry is operating properly.
If the voltage is not present as described, replace the
control circuit board.
Whipper Motor and Dispense Solenoid Circuitry:
1. Disconnect the dispenser from the power source.
2. With a voltmeter, back probe check the voltage
across pins 1 & 2 of the eight pin J1 connector
on the wiring harness. Connect the dispenser to
the power source. The indication must be 24 volts
ac.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 4.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
If the voltage is present as described, re-install the
probe. The liquid level control circuitry is operating
properly.
If the voltage is not present as described, check the
pink probe wire and green tank wire for continuity and
check the overflow protection switch.
4. Check that the RINSE/RUN switch is in the “Rinse”
position.
5. With a voltmeter, back probe check the voltage
across pins 2 & 4 of the six pin J2 connector on
the wiring harness. Connect the dispenser to the
power source. The indication must be:
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 or 120/240
volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
6. Disconnect the dispenser from the power source.
7. With a voltmeter check the voltage across the
terminals of the appropriate dispense solenoid.
Connect the dispenser to the power source. Press
the appropriate dispense switch. The indication
must be :
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 or 120/240
volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
Hopper Motor Control Circuitry:
1. Disconnect the dispenser from the power source.
2. With the voltmeter, back probe check the voltage
across pins 1 & 2 of the eight pin J1 connector on
the wiring harness. Connect the dispenser to the
power source. The indication must be 24 volts ac
from the transformer.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 4.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
4. Check that the “Rinse/Run” switch is in the “Run”
position.
21
42672 122209
SERVICE (cont.)
CONTROL BOARD (cont.)
If the voltage is present as described, the whipper motor and dispense solenoid control circuitry is operating
properly.
If the voltage is not present as described, replace the
control circuit board.
J1
J2
Removal and Replacement:
1. Disconnect the three plugs on the main wiring harness from the connectors on the control board.
2. Remove the four #6-32 keps nuts securing the
control board to the component bracket.
3. Remove control board and discard.
4. Install new control board on the component bracket
using four #6-32 keps nuts.
5. Reconnect the three plugs on the main harness to
the connectors on the control board.
J1
J3
J2
J4
J3
FIG. 11 CONTROL BOARD CONNECTORS
22
P1680
42672 122209
SERVICE (cont.)
CONTROL BOARD (FMD-3,-4,-5)
5. Disconnect the dispenser from the power source.
FMD-4 shown
If voltage is present as described, proceed to step 6.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
6. Carefully connect a piece of insulated jumper wire
to pin 10 (top right) of J2 on control board #1.
Keep the other end of this wire away from any metal
surfaces of the dispenser.
7. Check the voltage across the terminals of the
inlet solenoid valve with a voltmeter. Connect the
dispenser to the power source. The indication
must again be 120 volts ac for two wire 120 volt
models, three wire 120/208 volt models, three wire
120/240 volt models, or 230 volts ac for two wire
230 volt models after a delay of approximately 10
seconds.
8. Touch the free end of the jumper wire to the dispenser housing. The indication must be 0.
9. Move the jumper wire away from the housing. The
indication must again be 120 volts ac for two wire
120 volt models, three wire 120/208 volt models,
three wire 120/240 volt models, or 230 volts ac
for two wire 230 volt models after a delay of approximately 5 seconds.
10. Disconnect the dispenser from the power source
and remove the jumper wire.
J1
J2
J4
J3
J1
J2
J4
J3
#2
#1
FIG. 12 CONTROL BOARD
P4095
Location:
The Control Board(s) are located behind the
lower front access cover mounted on the component
bracket.
Test Procedure:
Liquid Level Control Circuitry(Control Board #1):
1. Disconnect the dispenser from the power source.
2. Back probe check the voltage across pins 5 & 6 of
the six pin J3 connector on the wiring harness with
a voltmeter. Connect the dispenser to the power
source. The indication must be 24 volts ac.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step
11.
If the voltage is not present as described, replace
control board #1.
11. Gently pull the liquid level probe out of the tank lid
and inspect for corrosion. Replace it if necessary.
12. Place the probe so that neither end is in contact
with any metal surface of the dispenser.
13. Check the voltage across the terminals of the
inlet solenoid valve with a voltmeter. Connect the
dispenser to the power source. The indication
must again be 120 volts ac for two wire 120 volt
models, three wire 120/208 volt models, three wire
120/240 volt models, or 230 volts ac for two wire
230 volt models after a delay of approximately 10
seconds.
If voltage is present as described, proceed to step 4.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
4. Back probe check the voltage across pins 1 & 4 of
the four pin J4 connector on the wiring harness with
a voltmeter. Connect the dispenser to the power
source. The indication must be 120 volts ac for
two wire 120 volt models, three wire 120/208 volt
models, three wire 120/240 volt models, or 230
volts ac for two wire 230 volt models.
23
42672 122209
SERVICE (cont.)
CONTROL BOARD (CONT.)
Tank Heater Relay Control Circuitry (Control Board #2)
(120V dispensers only):
1. Disconnect the dispenser from the power source.
2. Back probe check the voltage across pins 5 & 6 of
the six pin J3 connector on the wiring harness with
a voltmeter. Connect the dispenser to the power
source. the indication must be 24 volts ac.
3. disconnect the dispenser from the power source.
14. Move the probe’s flat end to the dispenser housing.
The indication must be 0.
15. Move the probe’s flat end away from the housing.
The indication must again be 120 volts ac for two
wire 120 volt models, three wire 120/208 volt
models, three wire 120/240 volt models, or 230
volts ac for two wire 230 volt models after a delay
of approximately 5 seconds.
16. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 4.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
If the voltage is present as described, re-install the
probe. The liquid level control circuitry is operating
properly.
If the voltage is not present as described, check the pink
probe wire and green tank wire for continuity.
4. Back probe check the voltage across pins 1 & 4 of
the four-pin J4 connector on the wiring harness
with a voltmeter. The indication must be 120 volts
ac.
5. Disconnect the dispenser from the power source.
Hopper Motor Control Circuitry (Stations 1-3, Control
Board #1 & Stations 4-5, Control Board #2):
1. Disconnect the dispenser from the power source.
2. Back probe check the voltage across pins 5 & 6 of
the six pin J3connector on the wiring harness with
a voltmeter. Connect the dispenser to the power
source. The indication must be 24 volts ac.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to step 6.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
6. Check the voltage across the coil terminals of the
tank heater relay with a voltmeter. Connect the
dispenser to the power source. The indication must
be 0 volts ac.
If voltage is present as described, proceed to step 4.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
If voltage is absent as described, proceed to step 7.
If voltage is present, replace the control circuit board
#2.
4. Check that the rinse/run switch is in the run position.
5. Check the voltage across the red (+) terminal and
the black (-) terminal of the auger motor with a voltmeter. Connect the dispenser to the power source.
Press and hold the appropriate dispense switch.
After a delay of about .6 seconds, the indication
must be between +4.0 and +24.5 volts dc.
7. Place containers below any three dispenser nozzles.
8. Simultaneously initiate dispenses at each of the
selected dispense stations while monitoring the
voltage across the coil terminals of the tank heater
relay. The indication must be 120V ac.
If the voltage is present as described, the hopper motor
control circuitry is operating properly.
If the voltage is not present as described, replace the
control circuit board.
If voltage is present as described, the control board #2
is functioning correctly.
If voltage is not present as described, replace the control
circuit board #2.
24
42672 122209
SERVICE (cont.)
CONTROL BOARD (CONT.)
Removal and Replacement:
1. Disconnect the three plugs on the main wiring harness from the connectors on the control board.
2. Remove the four #6-32 keps nuts securing the
control board to the component bracket.
3. Remove control board and discard.
4. Install new control board on the component bracket
using four #6-32 keps nuts.
5. Reconnect the three plugs on the main harness to
the connectors on the control board.
NOTE: J4 is not connected on Control Board #2 on
120/208 - 240V dispensers.
CONTROL BOARD #1 J1 J2
J1 J2
J1
J2
J4
J3
J1
J2
J4
J4
J3
J3
CONTROL BOARD #2
J4
J3
P2637
FIG. 13 CONTROL BOARD CONNECTORS
25
42672 122209
SERVICE (cont.)
Electronic Thermostat (Optional):
1. Disconnect the dispenser from the power source.
2. Disconnect the black wire of the control thermostat
from the black wire from the limit thermostat.
3. Remove temperature probe from the tank.
4. With a voltmeter, check the voltage across the black
wire from the control thermostat and the white wire
on the tank heater with the tank heater switch in
the “ON” (lower) position. Connect the dispenser
to the power source. The indication must be120
volts ac for two wire 120 volt models.
CONTROL THERMOSTAT (FMD-1,-2,-2FD,-3,-4,-5)
FMD-3 shown
If voltage is present as described the control thermostat
is operating properly. Reinstall temperature probe into
the tank.
If voltage is not present as described, replace the control
thermostat.
P1445
FIG. 14 CONTROL THERMOSTAT
Location:
The control thermostat (mechanical or electronic)
is located inside the dispenser on the upper left side
of the housing.
Removal and Replacement:
1. Disconnect the wires from the thermostat.
2. Remove the thermostat capillary bulb/temperature
probe by firmly pulling up on the capillary grommet
at the tank lid.
3. Loosen the two #8-32 screws securing the thermostat bracket to the upper left rear of the dispenser
housing.
4. Remove thermostat bracket and thermostat as an
assembly.
5. Install the new thermostat and bracket inside the
dispenser housing on the upper left rear side and
tighten the two #8-32 screws.
6. Slide the grommet to the line 4.5" above the bulb
on the new capillary tube (mechanical thermostat
only).
7. Insert the capillary bulb/temperature probe through
the hole in the tank lid and press the grommet firmly
and evenly so that the groove in the grommet fits
into the tank lid.
8. Carefully bend the capillary tube so that the tube and
bulb inside the tank are in the vertical position and
away from any electrical connections (mechanical
thermostat only).
9. Refer to Fig. 15 and reconnect the wires.
Test Procedure:
Mechanical Thermostat:
1. Disconnect the dispenser from the power source.
2. Disconnect the black wire of the control thermostat
from the black lead from the limit thermostat.
3. Remove bulb from the tank.
4. With a voltmeter, check the voltage across black
wire on the control thermostat and the white or red
wire on the tank heater with the tank heater switch
in the “ON” (lower) position. Connect the dispenser
to the power source. The indication must be:
a) 120 volts ac for two wire 120 volt models.
b) 208 volts ac for three wire 120/208 volt models.
c) 240 volts ac for two wire 240 volt models and
three wire 120/240 volt models.
d) 230 volts ac for two wire 230 volt models.
5. Disconnect the dispenser from the power source.
If voltage is present as described the control thermostat
is operating properly. Reinstall bulb into the tank.
If voltage is not present as described, replace the
thermostat.
NOTE - The capillary tube must be clear of any electrical
termination and not kinked.
26
42672 122209
SERVICE (cont.)
CONTROL THERMOSTAT (cont.)
TAN to WHI/BRN in
Main Wiring Harness
BLK to Main
Wiring Harness
WHI to Main
Wiring Harness
BLK from Limit
Thermostat
BLK from Tank
Heater Switch
BLK to Main
Wiring Harness
ELECTRONIC THERMOSTAT
MECHANICAL THERMOSTAT
FIG. 15 THERMOSTAT TERMINALS
P1448
27
42672 122209
SERVICE (cont.)
DISPENSE SWITCHES (FMD-1,-2,-2FD,-3,-4,-5)
If voltage is present as described, proceed to #7.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
FMD-5 shown
7. Check for continuity across the terminals (top right
to top left; bottom right to bottom left) of the dispense switch with the switch in the “ON” position.
Continuity must not present when the switch is in
the “OFF” released position.
FIG.16 DISPENSE SWITCHES
If continuity is present as described, reconnect the
connector to the door interconnect wiring harness, the
switch is operating properly.
If continuity is not present as described, replace the
switch.
P2636
Removal and Replacement
1. Open the dispenser door.
2. Remove the six #8-32 screws securing the bottom
door cover and remove cover.
3. Disconnect the wires on the dispense switch from
the door interconnect wiring harness.
4. Compress the clips inside the door on the dispense
switch and gently push the switch through the
opening
5. Push the new switch into the opening and spread
the clips to hold the switch in the door.
6. Reconnect the wires to the dispense switch from
the door interconnect wiring harness.
7. Reinstall the door bottom cover using six #8-32
screws.
8. Refer to schematic wiring diagrams when reconnecting the wires.
Location:
The dispense switches are located on the lower
outside of the dispenser door.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Open the dispenser door and remove the bottom
door cover.
3. Disconnect the wires from the door interconnect wiring harness to the dispense switch to be tested.
4. Check for voltage across the black and red/white
wires for the dispense switch to be teseted from
the door interconnect wiring harness. Connect the
dispenser to the power supply. The indication must
be:
a) 120 volts ac for two wire 120 volt models.
b) 120 volts ac for three wire 120/208 volt or 120/240
volt models.
c) 230 volts ac for two wire 230 volt models.
5. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to #6.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
6. With a voltmeter, check the voltage across the
remaining two wires of the dispense switch being
tested from the door interconnect wiring harness.
Connect the dispenser to the power source. The
indication must be +5 volts dc.
FIG. 17 DISPENSE SWITCH TERMINALS
28
P1449
42672 122209
SERVICE (cont.)
DIGITAL TOUCH CONTROL SWITCH (FMD DBC-2,DBC-3)
If voltage is present as described, proceed to step 7.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
FMD DBC-3 shown
7. While pressing the appropriate switch, check for
continuity across the following pins of the digital
touch control switch assembly’s multi-pin connector:
Note: Pin 1 of the connector is identified by an arrow
embossed on the connector housing.
FMD DBC-3:
Left Small : pin 1 to pin 2
Left Medium: pin 2 to pin 3
Left Large: pin 1 to pin 3
Stop: pin 1 to pin 4
Center Small: pin 1 to pin 5
Center Medium: pin 5 to pin 6
Center Large: pin 1 to pin 6
Right Small: pin 1 to pin 7
Right Medium: pin 7 to pin 8
Right Large: pin 1 to pin 8
Hot Water: pin 1 to pin 13
P1631
FIG.18 DIGITAL TOUCH CONTROL SWITCH
Location:
The digital touch control switch is located on the lower
outside of the dispenser door.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Open dispenser door and remove the bottom door
cover.
3. Disconnect the wires from the door interconnect
wiring harness to the digital touch control switch
assembly.
4. With a voltmeter, and using pin 1 of the multi-pin
connector of the door interconnect wiring harness
as a reference (-), check for voltage at each of the
other pins of the connector. Connect the dispenser
to the power source. The indication must be +5
volts dc.
5. On dispensers with a hot water valve, with a voltmeter, and using pin 1 of the multi-pin connector
of the door wiring harness as a reference (-), check
for voltage at pin 13 (blue/red wire). Connect the
dispenser to the power source. The indication must
be approximately 37 volts dc.
6. Disconnect the dispenser from the power source.
FMD DBC-2FD:
Left Small : pin 1 to pin 2
Left Medium: pin 2 to pin 3
Left Large: pin 1 to pin 3
Stop: pin 1 to pin 4
Right Small: pin 1 to pin 5
Right Medium: pin 5 to pin 6
Right Large: pin 1 to pin 6
Hot Water: pin 1 to pin 7
If continuity is present as described, the membrane
switch assembly is operating properly.
If continuity is not present as described, replace the
membrane switch assembly.
29
42672 122209
SERVICE (cont.)
DIGITAL TOUCH CONTROL SWITCH (cont.)
Removal and Replacement:
1. Open the dispenser door.
2. Remove the five #6-32 screws securing the bottom
door cover and remove cover.
3. Disconnect the wires on the dispense switch to be
removed from the door interconnect wiring harness.
4. From inside the door gently push the switch away
from the door and discard.
5. Remove the paper from the adhesive backing on
the switch and feed the ribbon cable on the back
of switch through the slot in the door.
6. Firmly press the new switch into the opening on
the door to hold the switch in the door.
7. Reconnect the wires to the dispense switch from
door interconnect wiring harness.
8. Reinstall the door bottom cover using five #6-32
screws.
9. Refer to Fig. 19 when reinstalling wires.
Align arrows on
connectors
TO DOOR INTERCONNECT
HARNESS CONNECTOR
FIG. 19 DIGITAL TOUCH CONTROL
SWITCH
30
P1685
42672 122209
SERVICE (cont.)
EMI FILTER (230 Volt FMD DBC-3)
Removal and Replacement:
1. Disconnect the wires from the EMI Filter.
2. Remove the two #8-32 screws and nuts securing
the EMI Filter.
3. Remove and discard EMI Filter.
4. Install new EMI Filter using two #8-32 screws and
nuts to secure EMI Filter to its former location.
5. Refer to schematic wiring diagrams when reconnecting the wires.
FIG. 20 EMI FILTER
Location:
The EMI Filter is located on the rear of the dispenser
base on FMD DBC-3.
118.0 kΩ - 118.5 kΩ
Across either pair
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Disconnect the two black wires and two white
wires on the EMI Filter from the EMI Filter wiring
harness.
3. Check for resistance between the two black leads
on the EMI Filter.
FIG. 21 EMI FILTER CONNECTORS
If resistance is present as described the EMI Filter is
operating properly.
If resistance is not present as described, replace the
EMI Filter.
31
42672 122209
SERVICE (cont.)
VACUUM FAN (all Models)
FMD DBC-3 shown
Removal and Replacement:
1. Disconnect the vacuum hose from the fan.
2. Remove the two #8-32 locking screws securing the
fan to the dispenser housing base plate.
3. Disconnect the wires from the fan terminals and
discard the fan
4. Refer to schematic wiring diagrams when reconnecting the wires.
5. Install new fan using two #8-32 locking screws.
6. Reconnect the vacuum hose to the fan.
BLK from Main
WiringHarness
P4102.40
FIG. 22 FAN
Location:
The fan is located inside the dispenser housing on
the right rear of the dispenser base plate.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Disconnect the black and white wires from the fan
terminals.
3. With a voltmeter, check the voltage across the
black and white wires. Connect the dispenser to
the power source. The indication must be:
a) 120 volts ac for two wire 120 volt, three wire
120/208 volt and 120/240 volt models.
b) 240 volts ac for two wire 240 volt models.
c) 230 volts ac for two wire 230 volt models.
WHI from Main Wiring Harness
FIG. 23 FAN TERMINALS
P1507
If voltage is present as described, replace the fan.
If voltage is not present as described, refer to Wiring
Diagrams and check the dispenser wiring harness.
32
42672 122209
SERVICE (cont.)
FROTHER AND WHIPPER MOTOR (all Models except -2FD)
FMD DBC-3 shown
11 12 13
1
2
P4102.40
FIG. 24 FROTHER AND WHIPPER MOTOR
Location:
The frothers are located behind the dispenser door,
mounted on the whipper motor shaft inside the whipper
chamber.
The whipper motors are located on the back side
of the whipper motor mounting panel.
10
9
8
7 6
5
4
3
FIG. 25 MIXING/WHIPPER CHAMBER
COMPONENTS
1.
2.
3.
4.
5.
6.
7.
Test Procedure:
1. Check that the rinse/run switch is in the rinse (up)
position.
2. Disconnect the dispenser from the power source.
3. Disconnect both wires from the black leads on the
motor to be checked.
4. Press and hold the appropriate dispense switch
and, with a voltmeter, check the voltage across the
disconnected harness. Connect the dispenser to the
power source. The reading must be:
a) 120 volts ac for two wire 120 volt models, three
wire 120/208 volt and 120/240 volt models.
b) 240 volts ac for two wire 240 volt models.
c) 230 volts ac for two wire 230 volt models.
5. Disconnect the dispenser from the power source.
Steam Collector
Mixing Chamber
Dispense Tip
Whipper Chamber
O-Ring
Frother
Nut
8.
9.
10.
11.
12.
13.
P1630.35
Receptacle w/Seal
Slinger
Motor Assy.
Fan
Vacuum Hose
Baffle
Removal, Cleaning & Replacement (Refer to Fig. 25):
1. Disconnect the dispenser from power.
2. Open the dispenser door and turn elbows up.
3. Remove the steam collectors (1) by pulling forward
and at the same time twisting clockwise.
4. Pull the mixing chamber (2) out of the whipper
chamber (4).
5. Remove dispense tip (3) and twist the whipper
chamber (4) clockwise and pull it off the whipper
chamber receptacle (8).
If voltage is present as described, replace the motor.
If voltage is not present as described, refer to the Wiring
Diagrams and check the dispenser wiring harness
33
42672 122209
SERVICE (cont.)
FROTHER AND WHIPPER MOTOR (cont.)
20. Install whipper chamber (4) on the whipper chamber
receptacle (8) by twisting counterclockwise until
the tabs on the whipper chamber (4) lock with the
tabs on the whipper chamber receptacle (8). Be
sure dispense port is pointing down.
21. Install dispense tip (3) into the bottom of the whipper chamber (4).
22. Slip the mixing chamber (2) onto the mixing chamber
water inlet tube far enough so the mixing chamber
(2) will seat inside the whipper chamber (4).
23. Install the steam collector (1) onto the mixing chamber (2) by pushing down and toward the dispenser
while twisting until the flange on the steam collector
lines up with the slot in the front panel.
24. Install hopper assembly in the dispenser by sliding hopper assembly on the hopper support panel
until the slot in the bottom rear of the hopper seats
against the shoulder screw in the hopper support
panel.
25. Reinstall side panel.
26. Reconnect to power and test.
6. Pull the frother (6) off the motor shaft. Notice the
flat side on the shaft and the matching flat inside
the frother. It is important that these two flats are
lined up when reassembling.
7. Slip the o-ring (5) off the whipper chamber receptacle (8).
8. Remove nearest side panel and disconnect whipper
motor wires.
9. Remove the two nuts (7) securing whipper chamber
receptacle (8) and whipper motor (10) to the front
panel.
NOTE: To remove the recptacle only, rotate clockwise
until the receptacle clears the nuts (7) and slides
off of the motor shaft.
10. Slide the receptacle with seal off of the motor
shaft.
11. Slide the slinger (9) off of the motor shaft.
12. Remove motor and discard.
13. Install new motor (10) on rear of front panel and
secure with two nuts (7) and connect black leads
on the motor to the main wiring harness. Refer to
Fig. 27 when reconnecting wires
14. Slide slinger (9) onto the motor shaft flush against
the front panel.
15. Wash remaining components in a mild solution of
dish detergent using a bristle brush.
16. Rinse thoroughly and allow to dry before reinstalling
in the dispenser.
17. Slide whipper chamber receptacle with seal (8) and
o-ring (5) on to the motor shaft.
18 Rotate the receptacle with seal (8) counterclockwise
until it snaps into place on the motor mounting nuts
(7).
19. Push frother (6) onto the motor shaft, making sure
the flat in the frother (6) lines up with the flat on
the motor shaft.
BLK to Main Harness
BLK to Main Harness
FIG. 26 WHIPPER MOTOR TERMINALS
34
P1451.40
42672 122209
SERVICE (cont.)
HOPPER DRIVE BOARD - FMD-1 ONLY
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring harness.
5. Check the voltage across the positive (red wire)
terminal and the negative (black wire) terminal on
the auger motor with a voltmeter. With the rinse/
run switch in the run (lower) position press and
hold the dispense switch. Connect the dispenser
to the power supply. After a .6 second delay the
indication must be 4.0 to 24.5 volts dc.
J1
If voltage is present as described,the auger motor drive
is operating properly. If auger does not turn replace
the auger motor.
If voltage is not present as described, replace the hopper drive board.
P1665
FIG. 27 HOPPER DRIVE BOARD
Location
The hopper drive board is located inside the dispenser
mounted on the auger motor mounting bracket.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Disconnect the white/red wire and the white wire
from the hopper speed control board.
3. Check the voltage across the white/red wire and
the white wire with a voltmeter. With the rinse/
run switch in the run (lower) position, connect the
dispenser to the power supply. The indication must
be:
a) 120 volts ac for two wire 120 volt models.
b) 120 volts ac for three wire 120/208 volt or
120/240 volt models.
c) 230 volts ac for two wire 230 volt models.
4. Disconnect the dispenser from the power supply.
35
42672 122209
SERVICE (cont.)
HOPPER DRIVE BOARD - FMD-1 ONLY
Removal and Replacement: (Refer to Fig. 27)
1. Remove hopper assy (17), and set aside for reassembly.
2. Remove the four #8-32 screws securing the hopper
support plate (12), remove plate and set aside for
reassembly.
3. Remove the four #8-32 screws, located inside the
dispener housing on the lower right front of the auger
motor mounting panel (21), securing auger motor
mounting bracket (18) and auger motor (19) to the
rear of the auger motor mounting panel (21).
4. Disconnect the wires from the terminals on the
hopper drive board and disconnect the three pin
plug (J1) from the hopper drive board.
5. Remove auger motor mounting bracket (18), auger
motor (19), dust seal (20) and hopper drive board
as an assembly.
6. Remove the two #8-32 screws securing the hopper
drive board to the auger motor mounting bracket.
7. Remove the two spacers from the hopper drive
board and discard board.
8. Install spacers on new hopper drive board.
9. Install new hopper drive board to the auger motor
mounting bracket using two #8-32 screws..
10. Refer to Fig. 22 and reconnect the wires to the
hopper drive board terminals.
11. Connect three pin plug from the potentiometer to
the hopper drive board J1. Refer to Fig. 28.
12. Install auger motor mounting bracket with auger
motor and hopper drive board to the rear of the auger
motor mounting panel using four #8-32 screws.
13. Install hopper support plate using four #8-32
screws.
14. Install hopper assy (17).
RED from Hopper
Motor
J1 Connector for
Three Pin Plug from
Potentiometer
BLK from
Hopper Motor
RED/WHI from
Main Harness
WHI from Main
Harness
P1669
FIG. 28 HOPPER DRIVE BOARD TERMINALS
36
42672 122209
SERVICE (cont.)
HOT/COLD SWITCH (Optional for FMD DBC-3)
Removal and Replacement:
1. Remove all wires from the switch terminals.
2. Remove the mounting nut on the front of the whipper motor mounting panel.
3. Remove the hot/cold switch from the rear of the
front panel and discard.
4. Reconnect the wires to the terminals on the rear of
the new switch.
5. Push new hot/cold switch through the hole on the
left side of the whipper motor mounting panel and
secure with mounting nut.
6. Refer to schematic wiring diagrams when reconnecting the wires.
TAN to Main Harness
FIG. 29 HOT/COLD SWITCH
RED to Main Harness
P1684.40
Location:
The hot/cold switch is located on the left side of the
whipper motor mounting panel.
WHI/YEL to
Cold Solenoid
FIG. 30 HOT/COLD SWITCH TERMINALS
P1208
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Disconnect the wires from the switch terminals.
3. With the switch in the “Cold” (upper) position check
for continuity between the center terminal and the
bottom terminal. With the switch in the “Hot”
(lower) position check for continuity between the
center terminal and the upper terminal.
If continuity is present as described, the hot/cold switch
is operating properly.
If continuity is not present as described, replace the
switch.
37
42672 122209
SERVICE (cont.)
INCREASE/DECREASE SWITCH (FMD-2,-2FD,-3,-4,-5)
Removal and Replacement:
1. Open the dispenser door.
2. Remove the facenut securing the increase/decrease
switch to the whipper motor mounting panel.
3. Remove switch with wires attached from the back
side of the whipper motor mounting panel.
4. Disconnect the wires from the switch and discard
the switch.
5. Refer to schematic wiring diagrams when reconnecting the wires.
6. Install new switch with wires attached through the
hole in the whipper mounting panel and secure with
facenut.
FMD-3 shown
FIG. 31 INCREASE/DECREASE SWITCH
P1666
FIG. 32 INCREASE/DECREASE SWITCH
TERMINALS
Location:
The increase/decrease switch is located on the lower
left front of the whipper motor mounting panel.
P1208
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Disconnect the wires from the switch terminals.
3. Check for continuity between the center terminal and
upper terminal with switch in the decrease position
(lower). Check for continuity between the center
terminal and the lower terminal with the switch in
the increase position (upper).
If continuity is present as described, the switch is
operating properly.
If continuity is not present as described, replace the
switch.
38
42672 122209
SERVICE (cont.)
LAMP HOLDER (all Models)
Removal and Replacement: (Refer to Fig. 33)
1. Open dispenser door (1).
2. Remove the five #6-32 screws securing lower door
panel (5) to the door (1) and remove cover.
3. Disconnect the door wiring harness from the door
interconnect wiring harness.
4. Remove five #6-32 screws securing the upper door
panel (4) to the door (1).
5. Remove the upper door cover (4), lamp (3), lamp
holders (2) and door wiring harness as an assembly.
6. Disconnect the wires from the lamp holder to be
replaced from the door wiring harness.
7. Rotate lamp (3) 90° and remove from lamp holders
(2).
8. Remove the #6-32 screw securing the lamp holder
(2) to be removed, remove lamp holder (2) and
discard.
9. Install new lamp holder (2) and secure with a #6-32
screw.
10. Connect the wires on the new lamp holder to the
door wiring harness, black wire to red wire, and
white wire to blue wire.
11. Install lamp (3) into lamp holders (2) and turn 90°
until the pins snap in place.
12. Install upper door panel (4), lamp (3), lamp holders
(2) and door wiring harness as an assembly using
five #6-32 screws.
13. Reconnect the plug on the door wiring harness
to the connector on the door interconnect wiring
harness.
14. Install the door lower panel (5) using five
#6-32 screws.
FMD DBC-3 shown
1
3
5
4
2
6
RE
E
AS
LE
N
HE
T
L,
TIL
ON
TT
SH
D
OL
dH
an
P IS
CU
2/3
L
FU
UN
BU
PU
FIG. 33 LAMP HOLDERS
1.
2.
3.
Door Assy
Lamp Holders
Lamp
4.
5.
6.
P1454.70
Upper Panel
Lower Panel
Starter W/Socket
Location:
The lamp holders are located on the front of the upper
panel behind the display panel.
LAMP REPLACEMENT (Refer to Fig. 33)
1. Remove the outside window and display graphic.
2. Remove the two #4-40 screws securing the inside
window to the door and remove window.
3. Rotate lamp (3) 90° and remove from the lamp
holders (2).
4. Insert new lamp (3) into lamp holders (2) and turn
90° until the pins snap in place.
5. Using two #4-40 screws secure the inside window
to the door.
6. Install outside window and slide display graphic
down between the inside window and the outside
window.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Remove upper door panel (4) and disconnect the
door wiring harness from the leads on the lamp
holders.
3. Remove lamp from lamp holders.
4. Check for continuity on each lead of the lamp holders.
If continuity is present as described, lamp holders are
operating properly.
If continuity is not present as described replace the
lamp holder.
39
42672 122209
SERVICE (cont.)
Removal and Replacement (Refer to Fig. 33):
1. Open dispenser door assy (1)
2. Remove the five #6-32 screws securing the door
lower panel (5) to the door assy (1).
3. Disconnect the leads on the starter socket from the
door wiring harness.
4. Remove lower door panel (5) and starter w/socket
(6) as assembly.
5. Compress the spring tabs on the socket and remove
socket from the door bottom cover (5).
6. Rotate starter 90° and remove from the starter
socket.
7. Insert new starter (6) into socket and turn 90° until
the pins snap in place.
8. Install new socket by compressing spring tabs on
the socket and pushing the socket up through the
hole in the lower door panel (5) and releasing spring
tabs.
9. Connect the sockets leads to the door wiring harness.
10. Install door lower panel (5) with starter and starter
socket on door assy (1) using five #6-32 screws.
LAMP STARTER and SOCKET
Location:
The lamp starter (6) is located inside the door assy (1)
on the top of the door lower panel (5).
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Disconnect the starter leads from the door wiring
harness.
3. Remove lamp starter from starter socket.
4. Check for continuity on each lead of the starter
socket.
If continuity is present as described the starter socket
is operating properly.
If continuity is not present as described replace the
starter socket.
6. Remove starter (6) from starter socket.
7. Check for continuity across the pins on the bottom
of the starter (6).
If continuity is present as described, replace the
starter.
If continuity is not present as described, starter is
operating properly.
Note: If continuity tests are both as described and lamp
does not light, replace the starter.
40
42672 122209
SERVICE (cont.)
LEVEL CONTROL BOARD AND LEVEL PROBE (FMD-1 only)
4. Disconnect the dispenser from the power
source.
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the wiring
diagram and check the dispenser wiring haness.
5. Reconnect the violet wire to terminal 1.
6. Carefully connect a piece of insulated jumper wire
to terminal 4. Keep the other end of this wire away
from any metal surface of the dispenser.
7. Check the voltage across terminals 1 & 3 with a
voltmeter. Connect the dispenser to the power
source. The indication must be:
a) 120 volts ac for two wire 120 volt models,
b) 120 volts ac for three wire 120/208 volt or
120/240 volt models,
c) 230 volts ac for two wire 230 volt models, after
a delay of approximately 5 seconds.
8. Touch the free end of jumper wire to the component
bracket. The indication must be 0.
9. Move the jumper wire away from the component
bracket. The indication must again be:
a) 120 volts ac for two wire 120 volt models,
b) 120 volts ac for three wire 120/208 volt or
120/240 volt models,
c) 230 volts ac for two wire 230 volt models, after
a delay of approximately 5 seconds.
10. Disconnect the dispenser from the power source
and remove the jumper wire from terminal 4.
J1
P1665
FIG. 34 LEVEL CONTROL BOARD AND PROBE
Location:
The level control board is located behind the lower
access panel mounted on the right side of the component bracket.
The Level probe is located on the left center of the
tank lid just in front of the overflow tube.
If voltage is present as described, the level control board
is operating properly, proceed to #11.
If voltage is not present as described, replace the level
control board.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Remove the violet wire from terminal 1 & pink wire
from terminal 4 of the circuit board.
3. Check the voltage across terminals 2 & 3 with a
voltmeter. Connect the dispenser to the power
source. The indication must be:
a) 120 volts ac for two wire 120 volt models.
b) 120 volts ac for three wire 120/208 volt or
120/240 volt models.
c) 230 volts ac for two wire 230 volt models.
11. Reconnect the pink wire to terminal 4.
12. Gently pull the probe out of the tank lid and inspect
for corrosion. Replace it if necessary.
41
42672 122209
SERVICE (cont.)
LEVEL CONTROL BOARD AND LEVEL PROBE (cont.)
13. Place the probe so that neither end is in contact
with any metal surface of the dispenser.
14. Check the voltage across terminals 1 & 3 with a
voltmeter. Connect the dispenser to the power
source. The indication must be:
a) 120 volts ac for two wire 120 volt models,
b) 120 volts ac for three wire 120/208 volt or
120/240 volt models,
c) 230 volts ac for two wire 230 volt models, after
a delay of approximately 5 seconds.
15. Move the probe’s flat end to the tank. The indication
must be 0.
16. Move the probe’s flat end away from the tank. The
indication should again be:
a) 120 volts ac for two wire 120 volt models,
b) 120 volts ac for three wire 120/208 volt or
120/240 volt models,
c) 230 volts ac for two wire 230 volt models, after
a delay of approximately 5 seconds.
If voltage is present as described, reinstall the probe,
the level control board and level probe are operating
properly.
If voltage is not present as described, check the pink
probe wire for continuity.
Removal and Replacement:
1. Remove all wires from the level control board.
2. Remove two #8-32 keps nuts holding level control
board to right side of the component bracket.
3. Remove level control board and spacers.
4. Install the new level control board and spacers to
the right side of the component bracket using two
#8-32 keps nuts.
5. Refer to schematic wiring diagrams when reconnecting the wires.
TI VIO to Inlet Solenoid Coil
T2 BLK to Main Harness
T3 WHI to Main Harness
T4 PNK to Probe
FIG. 35 LEVEL BOARD TERMINALS
42
P1671
42672 122209
SERVICE (cont.)
LIMIT THERMOSTAT (all Models)
If continuity is present as described, the limit thermostat
is operating properly.
If continuity is not present as described, replace the
limit thermostat.
FMD DBC-3 shown
Removal and Replacement:
1. Remove all wires from the limit thermostat terminals.
2. Carefully slide the limit thermostat out from under
the retaining clip and remove the limit thermostat.
3. Carefully slide the new limit thermostat into the
retaining clip.
4. Refer to schematic wiring diagrams when reconnecting the wires.
P4102.40
FIG. 36 LIMIT THERMOSTAT
Location:
The limit thermostat is located in the center of the
tank lid.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Disconnect both black wires from the limit thermostat.
3. Check for continuity across the limit thermostat
terminals.
FIG. 37 LIMIT THERMOSTAT TERMINALS
43
P1800
42672 122209
SERVICE (cont.)
OVERFLOW PROTECTION SWITCH (FMD-3,DBC-3-4,-5)
FMD DBC-3 shown
Removal and Replacement:
1. Disconnect the red leads from the overflow protection switch from the black wire and the blue wire
from the main harness.
2. Remove the nut beneath the copper overflow
cup.
3. Remove the entire switch assembly from the cup.
4. Place the new switch assembly into the cup, wires
first. Make sure that a gasket is in place around the
threaded switch stem.
NOTE - The magnets must be at the top of float and
there must be NO adjusting washers installed for the
overflow protection switch to operate properly.
5. Install the nut beneath the copper overflow cup. Be
sure not to overtighten.
6. Refer to schematic wiring diagrams when reconnecting wires.
P4102.40
FIG. 38 OVERFLOW PROTECTION SWITCH
Location:
The overflow protection switch is located inside the
copper overflow cup on the left side of the tank.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Remove the wire nuts connecting the red wires
from the overflow protection switch to the black
wire and blue wire from the main harness.
3. Check for continuity across the safety overflow
switch red wires only until the plastic float is raised
and check that continuity returns when the plastic
float is again lowered.
FIG. 39 OVERFLOW PROTECTION
SWITCH LEADS
P1212
If continuity is present as described, reconnect the
red wires to the black wire and the blue wire from the
main harness.
If continuity is not present as described, replace the
overflow protection switch.
44
42672 122209
SERVICE (cont.)
RINSE /RUN SWITCH (all Models)
Removal and Replacement:
1. Open the dispenser door.
2. Remove the facenut securing the run/rinse switch
to the whipper motor mounting panel.
3. Remove switch with wires attached from the back
side of the whipper motor mounting panel.
4. Disconnect the wires from the switch and discard
the switch.
5. Refer to schematic wiring diagrams when reconnecting the wires.
6. Install new switch with wires attached through
the hole in the whipper motor mounting panel and
secure with facenut.
FMD DBC-3 shown
P1684.40
FIG. 40 RINSE/RUN SWITCH
Location:
The rinse/run switch is located on the lower right side
of the whipper motor mounting panel.
FMD DBC-3,-2FD
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Disconnect the wires from the switch terminals.
3. Models FMD DBC-2FD and DBC-3: With the switch
in the “RUN” (lower) position check for continuity
between the center and the upper terminal. With
the switch in the “RINSE” (upper) position no
continuity should be present between center and
upper terminals.
Models FMD-2,-3,-4,-5: Check for continuity
between the center left terminal and left bottom
terminal, also between the center right terminal
and the right bottom terminal with the switch in the
rinse position (upper). Check for continuity across
the center left terminal and the top left terminal,
also between center right terminal and the top
right terminal with the switch in the run position
(lower). Continuity must not be present when the
switch is in the center position.
If continuity is present as described, the “RINSE/RUN”
switch is operating properly.
If continuity is not present as described, replace the
switch.
P1456
FMD-2,-3,-4,-5
P1644
FIG. 41 RINSE/RUN SWITCH TERMINALS
45
42672 122209
SERVICE (cont.)
7. Check the solenoid valve for coil action. Connect the
dispenser to the power source. With “HOT/COLD”
switch in the “COLD” (upper) position press the left
dispense switch and listen carefully in the vicinity
of the solenoid valve for a “clicking” sound as the
coil magnet attracts.
8. Disconnect the dispenser from the power source.
If the sound is heard as described and water will not
pass through the solenoid valve, there may be a blockage in the water line before the solenoid valve or, the
solenoid valve may require inspection for wear, and
removal of waterborne particles.
If the sound is not heard as described, replace the
solenoid valve.
SOLENOID VALVE (COLD WATER - OPTIONAL for
FMD-2,-3,-4,-5)
FMD DBC-3 shown
Removal and Replacement:
1. Loosen the two screws securing the component
bracket to the dispenser base. Lift the component
bracket off of the base and move to the right.
2. Remove the white and white/yellow wires from the
solenoid valve.
3. Turn off the water supply to the dispenser.
4. Disconnect the water lines to and from the solenoid
valve.
5. Loosen the two #8-32 screws and washers securing the solenoid mounting bracket to the base.
Remove solenoid bracket and solenoid valve as an
assembly.
6. Remove the two #10-32 screws and lockwashers securing the solenoid valve to the solenoid
bracket.
7. Using two #10-32 screws and lockwashers install
new solenoid valve on solenoid mounting bracket.
8. Install the solenoid valve and bracket on the dispenser base and tighten the two #8-32 screws.
9. Securely fasten the water lines to and from the
solenoid valve.
10. Refer to schematic wiring diagrams when reconnecting the wires.
P4102.40
FIG. 42 COLD WATER SOLENOID VALVE
Location:
The cold water solenoid valve is located on the left
side of the dispenser base just behind the component
bracket.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. With the “HOT/COLD” switch in the “COLD” (upper)
position press any left dispense switch on front of
the door.
3. With a voltmeter check the voltage across the white
and white/yellow wires at the solenoid terminals.
Connect the dispenser to the power source. The
indication must be:
a) 120 volts ac for two wire 120 volt models
b) 120 volts ac for three wire 120/208 or 120/240
volt models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
4. Disconnect the dispenser from the power
source.
If voltage is present as described, proceed to #5
If voltage is not present as described, refer to wiring
diagram and check dispenser wiring harness.
5. Disconnect the white and white/yellow wires from
the solenoid.
6. Check for continuity across the solenoid valve coil
terminals.
If continuity is present as described, reconnect the
white and white/yellow wires to the solenoid.
If continuity is not present as described, replace the
solenoid valve.
P1215
FIG. 43 COLD WATER SOLENOID TERMINALS
46
42672 122209
SERVICE (cont.)
6. Check the solenoid valve for coil action. Connect the
dispenser to the power source. With “RUN/RINSE”
switch in the “RINSE” (upper) position press the
appropriate dispense switch and listen carefully in
the vicinity of the solenoid valve for a “clicking”
sound as the coil magnet attracts.
7. Disconnect the dispenser from the power source.
If the sound is heard as described and water will not
pass through the solenoid valve, there may be a blockage in the tank water outlet before the solenoid valve
or, the solenoid valve may require inspection for wear,
and removal of waterborne particles.
If the sound is not heard as described, replace the
solenoid valve.
SOLENOID VALVES (DISPENSE) (all Models)
FMD DBC-3 shown
Removal and Replacement:
1. Remove the two wires from the solenoid valve.
2. Turn off the water supply to the dispenser.
3. Drain enough water from the tank (approximately
1.0 gallon) so the water level is below the dispense
valve mounting hole.
4. Disconnect the water line from the solenoid
valve.
5. Remove the #10-32 screw securing the solenoid
valve to side of the tank. Remove solenoid valve.
6. Using the #10-32 screw install new solenoid valve
on side of the tank
7. Push the water line onto the tube on bottom of
solenoid valve.
8. Refer to schematic wiring diagrams when reconnecting the wires.
P1637.40
FIG. 44 DISPENSE SOLENOID VALVES
Location:
The dispense solenoids are located on the side of
the tank.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. Disconnect the two wires from the solenoid valve.
With the “RUN/RINSE” switch in the “RINSE” (upper) position press the appropriate dispense switch
on front of the door.
3. With a voltmeter, check the voltage across the two
wires. Connect the dispenser to the power source.
The indication must be:
a) 120 volts ac for two wire 120 volt models, three
wire 120/208 volt, and 120/240 volt models.
b) 240 volts ac for two wire 240 volt models.
c) 230 volts ac for two wire 230 volt models.
4. Disconnect the dispenser from the power source,
If voltage is present as described, proceed to #5
If voltage is not present as described, refer to Wiring
Diagrams and check dispenser wiring harness.
to Dispense Switch
5. Check for continuity across the solenoid valve coil
terminals.
If continuity is present as described, reconnect the two
wires to the solenoid.
If continuity is not present as described, replace the
solenoid valve.
to Control Board
FIG. 45 DISPENSE SOLENOID VALVE
TERMINALS
47
P1645
42672 122209
SERVICE (cont.)
HOT WATER DISPENSE SOLENOID VALVE (FMD-2FD,DBC-2FD,-3,DBC-3)
6. Check the solenoid valve for coil action. Connect
FMD DBC-3 shown
the dispenser to the power source. Listen carefully
in the vicinity of the solenoid valve for a “clicking”
sound as the coil magnet attracts.
7. Disconnect the dispenser from the power source.
If the sound is heard as described and water will not
pass through the solenoid valve, there may be a blockage in the water line before the solenoid valve or the
solenoid valve may require inspection for wear, and
removal of waterborne particles.
If the sound is not heard as described, replace the
solenoid valve.
FIG. 46 HOT WATER DISPENSE
SOLENOID VALVE
Removal and Replacement:
1. Remove the white and blue wires from the solenoid
valve.
2. Turn off the water supply to the dispenser.
3. Drain enough water from the tank (approximately
2.0 gallons) so the water level is below the dispense
valve mounting hole.
4. Disconnect the water line from the solenoid
valve.
5. Loosen the #10-32 screw securing the solenoid
valve to side of the tank. Twist the solenoid valve
clockwise and remove solenoid valve.
6. Using the #10-32 screw install new solenoid valve
on side of the tank.
7. Push the water line onto the tube on bottom of
solenoid valve.
8. Refer to schematic wiring diagrams when reconnecting the wires.
P4102
Location:
The hot water solenoid valve is located on the left side
of the tank.
Test Procedures:
1. Disconnect the dispenser from the power source.
2. With a voltmeter check the voltage across the white
and blue wires at the solenoid valve. Connect the
dispenser to the power source. The indication must
be:
a) 120 volts ac for two wire 120 volt models
b) 120 volts for three wire 120/208 or 120/240 volt
models
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the wiring
diagram and check dispenser wiring harness.
4. Disconnect the white and blue wires from the solenoid valve.
5. Check for continuity across the solenoid valve coil
terminals.
If continuity is present as described, reconnect the
white and blue wires to the solenoid.
If continuity is not present as described, replace the
solenoid valve.
P1995.50
FIG. 47 HOT WATER DISPENSE
SOLENOID VALVE WIRING
48
42672 122209
SERVICE (cont.)
If the sound is heard as described and water will not
pass through the solenoid valve, there may be a blockage in the water line before the solenoid valve or, the
solenoid valve may require inspection for wear, and
removal of waterborne particles.
If the sound is not heard as described, replace the
solenoid valve.
SOLENOID VALVE (INLET) (all Models)
FMD DBC-3 shown
FIG. 48 INLET SOLENOID VALVE
Removal and Replacement:
1. Remove the two wires from the solenoid valve.
2. Turn off the water supply to the dispenser.
3. Disconnect the water lines to and from the solenoid
valve.
4. Remove the two #8-32 screws securing the solenoid to the dispenser base. Remove solenoid.
5. Install new solenoid valve on the dispenser base
and secure with the two #8-32 screws.
6. Securely fasten the water lines to and from the
solenoid valve.
7. Refer to Schematic Wiring Diagrams when reconnecting the wires.
P4102.40
Location:
The inlet solenoid is located inside on the rear of
the dispenser base.
Early Models
Test Procedures:
1. Disconnect the dispenser from the power
source.
2. Disconnect the two wires from the solenoid
valve.
3. Check for continuity across the solenoid valve coil
terminals.
120V 1.2 kΩ
230V 3.84 kΩ
Late Models
If continuity is present as described, reconnect the two
wires to the solenoid.
If continuity is not present as described, replace the
solenoid valve.
120V 622 Ω
230V 1555 Ω
4. Check the solenoid valve for coil action. Connect
the dispenser to the power source. Listen carefully
in the vicinity of the solenoid valve for a “clicking”
sound as the coil magnet attracts.
5. Disconnect the dispenser from the power source.
P1217
FIG. 49 INLET SOLENOID VALVE TERMINALS
49
42672 122209
SERVICE (cont.)
4. Disconnect the black wire and the white or red wire from
the tank heater terminals.
5. Disconnect the pink wire from the liquid level probe.
6. Disconnect the green wire from the tank.
7. Remove the thermostat capillary bulb/temperature probe
by firmly pulling up on the capillary at the tank lid. This
will disengage the grommet from the tank lid.
8. Remove the ten #8-32 nuts securing the tank lid to the
tank.
9. Remove tank lid with limit thermostat, liquid level probe
and tank heater as an assembly.
10. Remove the two hex nuts securing the tank heater to
the tank lid. Remove tank heater with gaskets and discard.
11. Install new tank heater with gaskets on the tank lid and
secure with two hex nuts.
12. Install tank lid with limit thermostat, liquid level probe
and tank heater on the tank and secure with ten #8-32
hex nuts.
13. Connect water inlet line to the tank lid.
14. Reconnect the black wires to limit thermostat, the pink
wire to the liquid level probe and the green wire to the
tank. Refer to the limit thermostat and the liquid level
board and probe sections in this manual when reconnecting wires.
15. Refer to Fig. 51 when reconnecting the wires to the tank
heater.
TANK HEATER (all Models)
FMD DBC-3 shown
FIG. 50 TANK HEATER
P4102.40
Location:
The tank heater is located inside the tank and secured to
the tank lid.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. With a voltmeter check the voltage across the black
and white wires 120 volt or 240 volt models or black
and red wires for 120/208 volt models or 120/240 volt
models. Connect the dispenser to the power source.
The indication must be:
a) 120 volts ac for two wire 120 volt models;
b) 208 volts ac for three wire 120/208 volt models.
c) 240 volts ac for three wire 120/240 volt models and
two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
3. Disconnect the dispenser from the power source.
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the dispenser
wiring diagram and check the wiring harness.
4. Disconnect the black wire and the white or red wire
from the tank heater terminals.
5. Check for continuity across the tank heater terminals.
If continuity is present as described, reconnect the wires,
the tank heater is operating properly.
If continuity is not present as described, replace the tank
heater.
120V
240V
Resistance Values
7.8 - 9.2 ohms @ 68° - 75°F
15.3 - 17.9 ohms @ 68° - 75°F
WHI or RED to Main
Wiring Harness
BLK to Limit
Thermostat
NOTE - If the tank heater remains unable to heat, remove
and inspect heater for cracks in the sheath.
Removal and Replacement:
1. Shut off water supply to the dispenser.
2. Disconnect the water supply tube on the tank lid.
3. Disconnect the black wires on the limit thermostat.
FIG. 51 TANK HEATER TERMINALS
50
P1218
42672 122209
SERVICE (cont.)
TANK HEATER RELAY (FMD-4,-5,120V Dispensers only)
6. With an ohmmeter, check for continuity between
the normally closed (NC-5) and common (COM-3)
terminals of the relay.
7. Place containers below any three dispense nozzles.
8. Connect the dispenser to the power source.
9. Simultaneously initiate dispenses at each of the
selected dispense stations while monitorintg continuity across the referenced terminals of the tank
heater relay. The indication must be open circuit.
J1
J2
J4
J3
J1
J2
If continuity is absent as described, the relay is functioning correctly.
If continuity is present, replace the relay.
J4
J3
P4095
FIG. 52 TANK HEATER RELAY
Removal and Replacement:
1. Loosen the three #8-32 screws securing the component bracket to the dispenser housing base.
2. Pull component bracket out the front of the dispenser far enough so the tank heater relay can be
disconnected from the main wiring harness.
3 Disconnect the tank heater relay from the main
wiring harness.
4. Remove the two #8-32 screws securing the tank
heater relay to the rear of the component bracket.
5. Remove and discard the tank heater relay.
6. Install new tank heater relay on the rear of the
component bracket and secure with two #8-32
screws.
7. Connect the tank heater relay to the main wiring
harness (see Fig. 53).
8. Place the component bracket into position and
tighten the three #8-32 screws.
Location:
The tank heater relay is located behind the lower
front access cover, mounted on the left rear side of the
component bracket.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Place the tank heater switch in the “OFF” (upper)
position.
3. With an ohmmeter, check for continuity between
normally closed (NC-5) and common (COM-3)
terminals of the relay. The indication must be less
than 1 ohm.
If continuity is present as described, proceed to step
4.
If continuity is not present as described, replace the
relay.
4. With an ohmmeter, check the resistance across the
coil terminals (1 & 2) of the relay. The indication
must be approximately 4,000 ohms (4kΩ).
If the resistance measures as described, proceed to
step 5.
If the resistance does not measure as described, replace
the relay.
BRN/BLK from
Main Harness
BLK from
Main Harness
5. Disconnect the wires from the normally closed (NC5) and common (COM-3) terminals of the relay.
BLK from
Main Harness
WHI from
Main Harness
No Connection
P2639
FIG. 53 TANK HEATER RELAY TERMINALS
51
42672 122209
SERVICE (cont.)
TANK HEATER SWITCH (all Models)
Removal and Replacement:
1. Refer to the hopper section in this manual and
remove the hopper assemblies and the hopper
support plate.
2. Remove the switch mounting nut on the front of
the front panel.
3. Remove switch with wires attached from the rear
of the front panel.
4. Remove the wires from the switch terminals and
discard switch.
5. Refer to schematic wiring diagrams when reconnecting the wires.
5. Push new switch through hole in the front panel
and secure with face nut.
7. Refer to the hopper section in this manual and
install the hopper support plate and the hopper
assemblies.
FMD DBC-3 shown
FIG. 54 TANK HEATER SWITCH
P1684.40
Location:
The tank heater switch located is inside the dispenser
on the upper right of the whipper motor mounting
panel.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Disconnect the black or white/brown wires from
the main harness.
3. With the switch in the “ON” (lower) position check
for continuity between the center and the upper
terminal. With the switch in the “OFF” (upper)
position no continuity should be present between
center and upper terminals.
If continuity is present as described, the heater “ON/
OFF” switch is operating properly.
If continuity is not present as described, replace the
switch.
P1219
FIG. 55 TANK HEATER SWITCH TERMINALS
52
42672 122209
SERVICE (cont.)
TRANSFORMER (all Models)
5. Check the voltage between J1-1 and J1-2 on the
eight pin connector at the control board. Connect
the dispenser to the power source. The indication
must be 24 volts ac.
If voltage is present as described the transformer is
operating properly.
If voltage is not present as described, replace the
transformer.
FMD DBC-3 shown
FIG. 56 TRANSFORMER
Removal and Replacement:
1. Loosen the two #8-32 screws securing the component bracket to the dispenser housing base.
2. Pull component bracket out the front of the dispenser
far enough so the transformer connector can be
disconnected from the main wiring harness.
3 Disconnect the transformer four pin connector from
the four pin plug on the main wiring harness.
4. Remove the two #6-32 keps nuts securing the transformer to the rear of the component bracket.
5. Remove and discard the transformer.
6. Install new transformer on the rear of the component
bracket and secure with two #6-32 keps nuts.
7. Connect the four pin connector on the transformer
to four pin plug on the main wiring harness.
8. Place the component bracket into position and
tighten the two #8-32 screws.
P1646
Location:
The transformer is located behind the lower
front access cover, mounted on the right rear side of
the component bracket.
Test Procedure:
1. Disconnect the dispenser from the power source.
2. Disconnect the four pin plug from the main harness
from the four pin connector on the transformer.
3 Check the voltage across black wire (pin 1) and
the
white wire (pin 2) on the plug from the main harness. Connect the dispenser to power source. The
indication must be:
a) 120 volts ac for two wire 120 volt models.
b) 120 volts for three wire 120/208 and 120/240
volt models.
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for two wire 230 volt models.
4. Disconnect the dispenser from the power source.
P1647
FIG. 57 TRANSFORMER TERMINALS
If voltage is present as described reconnect the plug
and the connector and proceed to #5.
If voltage is not present as described, refer to the wiring
diagrams and check the main wiring harness.
53
42672 122209
TRIAC MAPS for FMD
Q1
MOV1
Q2 MOV4
MOV2
Q5
MOV3
Q7
Bunn Part Number 28826.0006
Q1 & MOV1
Q2 & MOV3
Q5 & MOV4
Q7 & MOV2
controls
controls
controls
controls
Left Whipper Motor
Center Whipper Motor
Right Whipper Motor Refill Valve
@ J2-6
@ J2-3
@ J2-1
@ J2-5
Q1
MOV1
Bunn Part Number 38739.0000
Q1
MOV1
Bunn Part Number 38739.0001
Q1 & MOV1
controls
Refill Valve
54
@ J4
42672 122209
SCHEMATIC WIRING DIAGRAM FMD-1
GRN
L2
L1
HEATER
SWITCH
BLK-16
CONTROL
THERMOSTAT
BLK-16
BLK-16
LIMIT
THERMOSTAT
BLK-16
TANK HEATER
RED-16 (3-WIRE MODELS)
WHI-16 (2-WIRE MODELS)
BLK
FAN
BLK
WHI/RED
LIQUID
LEVEL
BOARD
RED
BLK
GRN
RED
RED
J1
GRN
VIO
BLK
SOL
RED
WHI
WHI
WHI
1 2 3
WHI
PROBE
GRN
HOPPER
WHIPPER
DISPENSE
SOL
1
2
3 PNK
4
HOPPER
DRIVE
PCB
RED
WHI
TANK INLET
HOPPER SPEED ADJUST
RUN/RINSE
SWITCH
N
RED
M
BLK
M
WHI
WHI
RED
BLK
FLUORESCENT
LAMP
BALLAST
BLK
BLU
1
RED
BLK
4
BLU
WHI
BLK
RED
GRN CHASSIS
DISPENSE SWITCH
BLU
WHI
BLK
RED
BLK
1
DOOR
BLU
WHI
BLK
BLU
BLU
RED
WHI
BLK
BLK
BLK STARTER
120 VOLTS A C - 2 WIRE
120/208-240 VOLTS AC - 3WIRE
SINGLE PHASE
RED
29096.0000C 8/98 © 1998 BUNN-O-MATIC CORPORATION
55
BLK
WHI
42672 122209
SCHEMATIC WIRING DIAGRAM FMD-1A
GRN
L2
L1
HEATER
SWITCH
BLK-16
CONTROL
THERMOSTAT
BLK-16
BLK-16
LIMIT
THERMOSTAT
THERMAL
FUSE
BLK-16
THERMAL
FUSE
TANK HEATER
WHI-16
BLK
FAN
BLK
TANK INLET
RED
RED
J1
WHI/RED
LIQUID
LEVEL
BOARD
RED
BLK
GRN
HOPPER SPEED ADJUST
RUN/RINSE
SWITCH
GRN
VIO
BLK
SOL
RED
WHI
WHI
WHI
1 2 3
WHI
PROBE
GRN
HOPPER
WHIPPER
DISPENSE
SOL
1
2
3 PNK
4
HOPPER
DRIVE
PCB
RED
WHI
RED
M
BLK
M
WHI
WHI
RED
BLK
FLUORESCENT
LAMP
BALLAST
BLK
BLU
1
RED
BLK
4
BLU
WHI
BLK
RED
GRN CHASSIS
DISPENSE SWITCH
BLU
WHI
BLK
RED
BLK
1
DOOR
BLU
WHI
BLK
BLU
BLU
RED
WHI
BLK
BLK
BLK STARTER
230 VOLTS AC CE
2 WIRE + GND
SINGLE PHASE 50/60 HZ
RED
29096.0006B 04/05 © 2005 BUNN-O-MATIC CORPORATION
56
BLK
WHI
42672 122209
SCHEMATIC WIRING DIAGRAM FMD-2
GRN
L1
TANK HEATER
SWITCH
CONTROL
THERMOSTAT
LIMIT
THERMOSTAT
BLK-16
BLK-16
L2
BLK-16
BLK-16
RED-16 (3-WIRE MODELS)
WHI-16 (2-WIRE MODELS)
TANK HEATER
BLK-16
BLK
BLK
WHI
WHI
VIO
J4-1
WHI
4
BLK
WHI/BLK
WHI/GRN
WHI
BLK
J3-1
VIO
WHI/BLK
WHI/GRN
WHI
BLK
J2-5
J2-10
SOL
WHI
BLK
GRN
BRN/BLK
GRY
YEL
WHI/ORN
WHI/YEL
RED/BLK
WHI/RED
GRN
GRN
PNK
J2-1
WHI
WHI/BLK
WHI/GRN
WHI
WHI/ORN
WHI/RED
GRN
WHI/GRN
WHI/BLK
J3-6
WHI
120V : 24V AC
TRANSFORMER
1
BLK
WHI
WHI
BLK
RINSE/PROGRAM/
RUN SWITCH
GRN
BLK
BLK
FLUORESCENT
LAMP
BALLAST
I
N
C
BLK
GRN
GRY
D
E
C
INCREASE/
DECREASE
SWITCH
YEL
BRN/WHI
BRN/BLK
BLU
PROBE
BRN/WHI
RED/BLK
RUN
GRN
PGM
RINSE
RUN
BLK
PGM
RINSE
GRN
RIGHT DISPENSE
ORN
WHI
M
WHI/ORN
RED
WHI/RED
RED
LEFT WHIPPER
WHI
SOL
RIGHT HOPPER
RIGHT WHIPPER
ORN
WHI
SOL
LEFT DISPENSE
TAN
RED
BLK
GRN
BLK
GRN
LEFT HOPPER
WHI
M
M
M
ORN
RED
RED
TAN
WHI
1
COLD DRINK OPTION (LEFT ONLY)
BLU
BLU
SOL
WHI
RED
RED
RED
WHI
GRN/BLK
WHI/BLK
PNK
1
ORN
BRN/WHI
RED
BLU
WHI
1
RED/WHI
BLK
RED
1
BLK/WHI
ORN
BLU/WHI
1
4
BLU
WHI
GRY
1
WHI/ORN
GRN
WHI/RED
4
GRN
WHI/YEL
C
O
N
T
R
O
L
P
C.
B.
O
A
R
D
FAN
TANK INLET
WHI
J4-4
N
CHASSIS
4
120 VOLTS AC - 2 WIRE
120/208-240 VOLTS AC - 3 WIRE
SINGLE PHASE, 60 HZ
G
R
N
DOOR
29096.0001C 10/98 © 1998 BUNN-O-MATIC CORPORATION
WHI
BLU
"RINSE" L.E.D.
BLU
BLU
1
ORN
BLK
BLU/WHI
RED
LEFT DISPENSE SWITCH
ORN
BLK
BLK/WHI
RED/WHI
JUMPER PLUG MUST BE
USED WHEN COLD
DRINK FEATURE NOT
INSTALLED
RED
BLK
BLK
RED
WHI
BLK
STARTER
BLK
WHI
RIGHT DISPENSE SWITCH
57
42672 122209
SCHEMATIC WIRING DIAGRAM FMD-2A
GRN
L1
TANK HEATER
SWITCH
CONTROL
THERMOSTAT
THERMAL
FUSE
LIMIT
THERMOSTAT
BLK-16
BLK-16
L2
BLK-16
BLK-16
TANK HEATER
BLK-16
BLK
BLK
WHI
WHI
VIO
J4-1
WHI
4
BLK
WHI/BLK
WHI/GRN
WHI
BLK
J3-1
VIO
WHI/BLK
WHI/GRN
WHI
BLK
J2-5
J2-10
WHI
SOL
WHI
BLK
GRN
BRN/BLK
GRY
YEL
WHI/ORN
WHI/YEL
RED/BLK
WHI/RED
GRN
GRN
PNK
J2-1
WHI
WHI/BLK
WHI/GRN
WHI
WHI/ORN
WHI/RED
GRN
WHI/GRN
WHI/BLK
J3-6
FAN
240V : 24V AC
TRANSFORMER
1
BLK
WHI
WHI
BLK
RINSE/PROGRAM/
RUN SWITCH
GRN
BLK
BLK
FLUORESCENT
LAMP
BALLAST
I
N
C
BLK
GRN
GRY
D
E
C
INCREASE/
DECREASE
SWITCH
YEL
WHI/BRN
BRN/BLK
BLU
PROBE
WHI/BRN
RED/BLK
RUN
GRN
PGM
RINSE
RUN
BLK
PGM
RINSE
GRN
RIGHT DISPENSE
ORN
WHI
M
WHI/ORN
RED
WHI/RED
RED
LEFT WHIPPER
WHI
SOL
RIGHT HOPPER
RIGHT WHIPPER
ORN
WHI
SOL
LEFT DISPENSE
TAN
RED
BLK
GRN
BLK
GRN
LEFT HOPPER
WHI
M
M
M
ORN
RED
RED
TAN
WHI
1
COLD DRINK OPTION (LEFT ONLY)
BLU
BLU
SOL
WHI
RED
RED
RED
WHI
GRN/BLK
WHI/BLK
PNK
1
ORN
WHI/BRN
RED
BLU
WHI
1
RED/WHI
BLK
RED
1
BLK/WHI
ORN
BLU/WHI
1
4
BLU
WHI
GRY
1
WHI/ORN
GRN
WHI/RED
4
GRN
WHI/YEL
C
O
N
T
R
O
L
P
C.
B.
O
A
R
D
WHI-16
TANK INLET
WHI
J4-4
THERMAL
FUSE
CHASSIS
4
230 VOLTS AC
2 WIRE + GND
SINGLE PHASE, 50 HZ
G
R
N
DOOR
29096.0005B 04/05 © 2005 BUNN-O-MATIC CORPORATION
WHI
BLU
"RINSE" L.E.D.
BLU
BLU
1
ORN
BLK
BLU/WHI
RED
LEFT DISPENSE SWITCH
ORN
BLK
JUMPER PLUG MUST BE
USED WHEN COLD
DRINK FEATURE NOT
INSTALLED
BLK/WHI
RED/WHI
RED
BLK
BLK
RED
WHI
BLK
STARTER
BLK
WHI
RIGHT DISPENSE SWITCH
58
42672 122209
SCHEMATIC WIRING DIAGRAM FMD DBC-2
FREEZE DRIED W/HOT WATER
GRN
HOT WATER
WHI/VIO
WHI
SOL
RIGHT HOPPER
RIGHT DISPENSE
ORN
WHI
SOL
LEFT HOPPER
LEFT DISPENSE
RED
WHI
SOL
1
4 1
RED
ORN
WHI/RED
WHI/ORN
WHI/BLU
GRY
CHASSIS
GRN
GRN
RED/BLK
BRN/BLK
BLK
BLK
GRN/BLK
RED/WHI
41
4
SWITCH UNIT ASSY
DOOR
BLU
WHI
BLK
FLUORESCENT
LAMP
BALLAST
BLU
WHI
1
1
WHI
BLK
RED
BLU
BLU
BLK
STARTER BLK
BLK
WHI
CENTER
LEFT
RED
BLU
S
M
M
D
L
G
STOP
S
M
M
D
L
G
HOT
WATER
29096.0003B 05/02 © 2002 BUNN-O-MATIC CORPORATION
59
42672 122209
SCHEMATIC WIRING DIAGRAM FMD-2FD
L1
L2
N
GRN
BLK-16
TANK HEATER
SWITCH
BLK-16
CONTROL
THERMOSTAT
LIMIT
THERMOSTAT
BLK-16
RED-16 (3-WIRE MODELS)
WHI-16 (2-WIRE MODELS)
TANK HEATER
BLK-16
BLK
BLK
FAN
WHI
WHI
J3-6
J2-5
J2-10
120V : 24V AC
TRANSFORMER
4
WHI
BLK
GRY
RUN
YEL
RINSE
WHI/GRY
RINSE/RUN
SWITCH
GRN
BLK
BLU
BLK
BLK
WHI/GRY
I
N
C
FLUORESCENT
LAMP
BALLAST
PROBE
INCREASE/
DECREASE
SWITCH
D
E
C
BRN/WHI
DISP
GRN
PGM
DISP
BLK
PGM
BRN/BLK
RED/BLK
GRN
DISPENSE/PROGRAM
SWITCH
WHI
WHI
RIGHT DISPENSE
ORN
SOL
RIGHT HOPPER
WHI
WHI/ORN
RED
WHI/RED
RED
LEFT DISPENSE
RED
SOL
M
1
4
1
WHI/VIO
ORN
BRN/WHI
RED
1
1
4
1
GRN/BLK
WHI/BLK
PNK
SOL
GRN
M
BLK
GRN
GRN
WHI
CHASSIS
ORN/BLK
RED/WHI
BLK
RED
GRN
WHI/YEL
WHI/VIO
BLK
LEFT HOPPER
WHI
HOT WATR
GRY
WHI
BLK
GRN
GRN
WHI/BLK
WHI/GRN
SOL
1
BLK
BRN/BLK
GRY
YEL
WHI/ORN
WHI/YEL
RED/BLK
WHI/RED
GRN
GRN
PNK
J2-1
BLU
WHI
B
O
A
R
D
WHI/ORN
WHI/RED
GRN
WHI/GRN
WHI/BLK
BLU
WHI
C.
WHI
BLK
WHI/ORN
GRN
WHI/RED
P.
J3-1
VIO
WHI/BLK
WHI/GRN
BLK/WHI
ORN
BLU/WHI
C
O
N
T
R
O
L
J4-4
TANK INLET
WHI
WHI
VIO
WHI
BLK
J4-1
WHI
BLU
BLU
BLU
RED
1
G
R
N
DOOR
WHI
BLK
BLK
BLK STARTER
RED
BLK
WHI
"RINSE" L.E.D.
ORN
BLK
BLU/WHI
RED
LEFT DISPENSE SWITCH
ORN
BLK
BLK/WHI
RED/WHI
RIGHT DISPENSE SWITCH
BLK
ORN/BLK
HOT WATER
DISPENSE SWITCH
White Strip-Tac Plus
Black Ink
Finished Size: 6.25" x 7.20"
≈62% Reduction
60
120 VOLTS AC - 2 WIRE
120/208-240 VOLTS AC - 3 WIRE
SINGLE PHASE, 60 HZ
29096.0004A 01/03 © 2003 BUNN-O-MATIC CORPORATION
42672 122209
61
42672 122209
62
42672 122209
63
42672 122209
64
42672 122209
RED
L2
N
WHI
L1
GREEN
BLK
SCHEMATIC WIRING DIAGRAM FMD DBC-3
(WITH HOT WATER DISPENSE)
BLK (2-WIRE MODELS)
MAIN ON/OFF SWITCH
(Late 3-wire Models only)
BLK (3-WIRE MODELS)
RED (3-WIRE MODELS)
WHI (2-WIRE MODELS)
120 VOLTS AC 2 WIRE + GND or
120/208-240 VOLTS AC - 3 WIRE + GND
SINGLE PHASE, 60 Hz
29218.0002D 03/07 © 1999 BUNN-O-MATIC CORPORATION
65
42672 122209
SCHEMATIC WIRING DIAGRAM FMDA DBC-3
(WITH HOT WATER DISPENSE)
L1
L2
GRN/YEL
TANK HEATER
SWITCH
LIMIT
THERMOSTAT
CONTROL
THERMOSTAT
BLK-16
BLK-16
BLK-16
TANK HEATER
BLK-16
WHI
BLU/BLK
BLU/BLK
BLK
BLK
WHI
FAN
WHI
PNK
J1-1
J1-5
J1-8
PROBE
BLK
WHI
WHI/GRN 120V : 24V AC
WHI/BLK TRANSFORMER
BLK
WHI
WHI/GRN
WHI/BLK
WHI/GRN
WHI/BLK
PNK
GRN
WHI/ORN
WHI/BLU
WHI/RED
GRN
TANK INLET
OVERFLOW SWITCH
BLU
GRN
RED
RED
VIO
WHI
SOL
N.C.
WHI/VIO
BLK
ORN
WHI
BLU
RED
J2-1
J2-5
WHI
C
O
N
T
R
O
L
RIGHT WHIPPER
RIGHT DISPENSE
WHI/VIO
WHI/VIO
WHI
SOL
CENTER DISPENSE
ORN
ORN
TAN
B
O
A
R
D
RED
WHI
SOL
RED
RED
TAN
WHI
WHI/BLU
RED
M
WHI/ORN
RED
RED
RED
TAN
M
GRN
M
BLK
GRN
BLK
GRN
LEFT HOPPER
WHI/RED
WHI
COLD DRINK OPTION (LEFT ONLY)
HOT/COLD SWITCH
WHI/YEL
TAN
BLK
M
CENTER HOPPER
WHI
LEFT WHIPPER
LEFT DISPENSE
P
C
RIGHT HOPPER
WHI
CENTER WHIPPER
WHI
SOL
M
SOL
WHI
RED
RED
RED
RED
M
JUMPER PLUG MUST BE
USED WHEN COLD
DRINK FEATURE NOT
INSTALLED
WHI
RED/BLK
BRN/BLK
WHI/BRN
WHI/VIO
WHI/BLU
ORN
GRN
BLU
GRY
RED
WHI/RED
WHI/ORN
J3-10
HOT WATER
RUN
J3-5
BLU
RINSE
J3-1
BLU
WHI
SOL
GRN
BLK
DOOR
WHI
BLK
RED
BLU
WHI
CHASSIS
BLU
WHI
GRN
BLU
BLU
BLK
STARTER BLK
BLK
WHI
J2-5
BLU
BLK
BLU/BLK
WHI
WHI
BLU/BLK
J2-1
J1-1
WHI/RED
WHI/ORN
WHI/BLU
GRY
RED
ORN
WHI/VIO
AUX. CONTROL PC BOARD
SWITCH UNIT ASSY
BLK
FLOURESCENT
LAMP
BALLAST
RED/BLK
BRN/BLK
WHI/BRN
GRN
DISCONNECT
TO ENABLE
RINSE TIMER
RED-22
BLU-22
WHI/VIO-22
GRN-22
BLK
J4-4
RED-22
GRN-22
BLU-22
WHI/VIO-22
J4-1
GRN/BLK
RED/WHI
RED
BLK
WHI/BLK
ORN
BLU/WHI
BLU/BLK
RED/BLK
ORN/BLK
BLK/WHI
WHI/RED
BLU/RED
RED
BLU
CENTER
LEFT
230 VOLTS AC - 2 WIRE
SINGLE PHASE
50/60 HZ
S
M
M
D
L
G
STOP
S
M
M
D
RIGHT
L
G
S
M
M
D
READY
L
G
HOT
WATER
29218.0004A 09/01 © 2001 BUNN-O-MATIC CORPORATION
66
42672 122209
67
42672 122209
68
42672 122209
69
42672 122209
70
42672 122209
SCHEMATIC WIRING DIAGRAM FMD-5A
L1
L2
GRN
TANK HEATER
SWITCH
BLK-16
CONTROL
THERMOSTAT
K
BLK-16
LIMIT
THERMOSTAT
BLK-16
THERMAL
FUSE
WHI
BRN/BLK
WHI
BLK
THERMAL
FUSE
TANK HEATER
BLK-16
BLK-16
WHI-16
K
J4-1
J4-4
FAN
BLK
BLK
BLK
WHI
VIO
WHI
WHI/VIO
J4-1
C
O
N
T
R
O
L
C
I
R
C
U
I
T
B
O
A
R
D
#
1
BLK
J4-4
LAMP #1 BLK
BALLAST
RED
RED
BLK LAMP #2 BLK
BALLAST
WHI
M
BLK
WHI/BLU
WHI/YEL
GRN
WHI/GRN
WHI/BLK
WHI
REFILL VALVE
BLK
LOAD 240V : 24V AC LINE
TRANSFORMER
WHI
WHI/GRN
WHI/BLK
OVERFLOW PROTECTION SWITCH
RED
RED
WHI/VIO
BLK
BLK
VIO
WHI/VIO
GRY
WHI/GRY
WHI/BLU
BLU/BLK
RED/BLK
WHI/YEL
WHI/ORN
WHI
SOL
WHI
WHI/ORN
WHI/RED
BRN/WHI
GRN
WHI/GRN
WHI/BLK
J3-1
J3-5
WHI/BLK
J3-1
J3-5
J2-1
J2-5
C
O
N
T
R
O
L
C
I
R
C
U
I
T
B
O
A
R
D
#
2
J2-10
J1-1
WHI/VIO
GRY
WHI/GRY
WHI/RED
TAN
RED/BLK
WHI/BLK
WHI/ORN
GRN
PNK
WHI
WHI
SOL
WHI
1
ORN
WHI
SOL
M
GRN
STATION #5
WHIPPER
BLK
STATION #4
DISPENSE
VALVE
YEL
SOL
BLK
BLK
WHI
M
BLK
STATION #5
DISPENSE
VALVE
BLU
SOL
WHI
BLK
BLU
STATION #3
DISPENSE
VALVE
M
GRN
STATION #4
WHIPPER
BLK
M
RED
WHI
1
RED
RED
TAN
WHI
HOT/COLD SWITCH
COLD
WHI/YEL
SOL
HOT
RED
RED
RED
JUMPER PLUG MUST BE
USED WHEN COLD
DRINK FEATURE NOT
INSTALLED
4
4
GRN
BLK/RED
WHI
PNK
BLU/RED
WHI
6
HOPPER #5
WHI/BLU
BLK
BLK/RED
WHI
BLU/RED
RED/WHI
BLU/WHI
GRY
1
"RINSE" #1-3 L.E.D.
1
RED
WHI
RED
BRN
RED
ORN
YEL
BLU
BRN/BLK
6
M
COLD DRINK OPTION (LEFT ONLY)
BRN
BRN
TAN
WHI
WHI/BLK
RED/BLK
ORN/BLK
GRN/BLK
BLU/BLK
BLK
1
BLK/WHI
RED
ORN
GRN/WHI
BLU
WHI/RED
1
WHI/BLK
WHI/RED
WHI/ORN
WHI/YEL
WHI/BLU
GRN
TAN
GRN
BLU/BLK
GRN
PNK
BLK
WHI
STATION #2
DISPENSE
VALVE
RED
RED
WHI
SOL
WHI/YEL
STATION #3
WHIPPER
BLK
M
WHI
TAN
RUN
HOPPER #4
BLK
M
WHI
BLK
WHI
BRN
BLK
RED
STATION #2
WHIPPER
BLK
STATION #1
DISPENSE
VALVE
GRN
RUN
RINSE
PGM
M
WHI
BRN/BLK
PGM
BLK
RED
RINSE/PROGRAM/
RUN SWITCH
WHI/GRY RINSE
WHI/ORN
GRN
STATION #1
WHIPPER
PROBE
GRY
BRN/BLK
HOPPER #3
BLK
M
WHI
RED
GRN
WHI/RED
BLU
HOPPER #2
BLK
YEL
M
WHI
RED
YEL
HOPPER #1
BRN/WHI
WHI
INCREASE/
DECREASE
SWITCH
ORN
WHI/VIO
GRN
D
E
C
ORN
I
N
C
J1-4
GRN
J1-1
RED
J2-10
J1-4
GRN
J2-5
WHI/RED
RED/BLK
J2-1
RED/GRN
ORN/RED
RED
BLU
BLK
WHI
BLU
BLU/BLK
RED
RED
WHI/RED
BLK
BLK
STARTER BLK
5
GRN/WHI
GRN/BLK
BLU
RED
WHI/RED
BLK
WHI
BLK
4
ORN
ORN/BLK
RED
BLU
WHI/RED
BLK
BLK
WHI
3
RED
RED/BLK
RED
RED
WHI/RED
BLK
BLK
STARTER BLK
2
BLK/WHI
WHI/BLK
BLU
RED
1
WHI/RED
BLK
WHI
BLK
GRY
1
"RINSE" #4 & 5 L.E.D.
230 VOLTS AC
2 WIRE + GND
SINGLE PHASE, 50/60HZ
34820.0002B 04/05 ©2005 BUNN-O-MATIC CORPORATION
71
42672 122209
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising