Bunn | Single® TF ThermoFresh® DBC® Black 120/240V | Service manual | BUNN Single® TF ThermoFresh® DBC® Black 120V Single BrewWISE® ThermoFresh® DBC® 120V Brewer w/Funnel Locks Service Manual

BUNN Single® TF ThermoFresh® DBC® Black 120V Single BrewWISE® ThermoFresh® DBC® 120V Brewer w/Funnel Locks Service Manual
RELEASED FOR PRODUCTION
DUAL TF BREWING INSTRUCTIONS
1. Insert a BUNN® filter into the 2. If a grinder is not used to obtain 3. If a G9-2T DBC or MHG grinder 4. Shake funnel gently to level
funnel.
the coffee grounds, pour in fresh is used with a compatible Smart grounds.
coffee.
Funnel®, select the desired batch
size on the grinder. Grind the
selected amount of fresh coffee
into the funnel.
5. Slide funnel into funnel rails 6. Place empty servers beneath 7. If a compatible DBC grinder 8. The ON/OFF switch must be in
of the brewer. The brewer will the funnel.
was not used, select the desired the “ON” position.
read the size ground through the
batch size.
chip in the funnel handle and will
automatically select the correct
size to brew.
9. Momentarily press and release
the BREW switch. If the brewer
has the funnel lock option and it
is activated, the funnel is locked
in place.
10. There may be some situations
in which the brew cycle will not
begin when the BREW switch is
pressed.
a) ON/OFF must be ON.
b) BREW TEMPERATURE TOO
LOW - wait until heated or
cancel BREW LOCKOUT option.
c) FUNNEL NOT IN PLACE (or
using a standard brew funnel)
- cancel FUNNEL DETECT.
d) CHECK FUNNEL - remove funnel, empty previously brewed
grounds and grind a new
batch into the funnel.
11. If none of the previous messages are displayed, the display
will read NOW BREWING and
the time remaining in the brew
cycle.
39482.0000A 10/06 ©2006 Bunn-O-Matic Corporation
DIR Num: 39482.0000
19, May 2015
12. Following the BREW will be
a countdown of DRIPPING time
which shows the time remaining
until the funnel lock will release.
Discard the grounds and filter
only after visible dripping stops.
RELEASED FOR PRODUCTION
DUAL TF CLEANING INSTRUCTIONS
1. Clean and sanitize funnels.
2. Use a clean damp cloth rinsed 3. Remove sprayheads from
in mild, non-abrasive detergent to brewer. Disassemble by removclean both sides of the sprayhead ing the seal.
panel.
5. Use the pointed end of sprayhead cleaning tool to remove any
mineral deposits from the sprayhead holes. The sprayhead holes
must always remain open.
6. Reassemble sprayheads and 7. The use of a damp cloth rinsed
reattach. Sprayheads only need in any mild, nonabrasive, liquid
to be hand tightened.
detergent is recommended for
cleaning all surfaces on Bunn-OSee installation and operating Matic equipment. Do NOT clean
manual for calibration routine this equipment with a water jet
to verify sprayhead flow rate device.
matches programmed flow rate.
Machine may need to be recalibrated due to lime build up
or the use of alternate designed
sprayheads. If machine is cleaned
and build up removed, machine
must be re-calibrated to achieve
desired volumes.
NOTE: Any buildup on the sprayhead and fitting may restrict water
flow, and impact your coffee
brewing. For consistently great
coffee, clean sprayheads and
fittings weekly with sprayhead
cleaning tool (#38227.0000).
Upon visual inspection it may appear that light passes through all
holes in the sprayhead plate, but a
thin film of residue can pass light
and still impede water flow.
4. Insert the long end of sprayhead
cleaning tool into the sprayhead
fittings, and rotate several times
to remove any mineral deposits
from the fitting.
39482 101206
DIR Num: 39482.0000
19, May 2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising