Bunn | Single® SH Soft Heat® DBC® Stainless 120/240V | Installation guide | BUNN Single® SH Soft Heat® DBC® Stainless, 120V Single BrewWISE® Soft Heat® DBC® 120V w/Fnl Lks & Lwr Faucet Installation Guide

BUNN Single® SH Soft Heat® DBC® Stainless, 120V Single BrewWISE® Soft Heat® DBC® 120V w/Fnl Lks & Lwr Faucet Installation Guide
SH DBC ® SERIES
BLE
F
/ OF
ENA
ON
W
BRE
BLE
BLE
F
/ OF
F
/ OF
ENA
ENA
ON
ON
W
W
BRE
BRE
BLE
F
/ OF
ENA
ON
W
BRE
BLE
F
/ OF
ENA
ON
W
BRE
SINGLE ®
DUAL®
WITH SMART FUNNEL®
S/N DUAL068000 & UP
DUAL®
.5 & 1.0 Gallon Low Profile
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please
visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way
to obtain the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-2866070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.
52187.0000B
08/17 ©2015 Bunn-O-Matic Corporation
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCR/MCP/MCA single cup brewers, thermal servers
and ThermoFresh® servers (mechanical and digital) 1 year parts and 1 year labor.
2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:
a) Electronic circuit and/or control boards - parts and labor for 3 years.
b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.
c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and labor for 4
years or 40,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially
free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period.
This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment,
has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, non periodic
cleaning and descaling, equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not apply
to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217)
529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective
equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make
additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute
warranties and should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the
equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor
warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service
Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT,
WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN,
TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other
special, incidental or consequential damages.
392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE,
BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line,
BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized
Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the stylized
leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, TRIFECTA (sylized
logo), Velocity Brew, Air Brew, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not bitter., Build-A-Drink, BUNNSource,
Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control, Element, Milk Texturing Fusion, Nothing Brews Like a
BUNN, Picture Prompted Cleaning, Pouring Profits, Signature Series, Sure Tamp, Tea At Its Best, The Horizontal Red Line, Ultra are
either trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing configuration is
a trademark of Bunn-O-Matic Corporation.
INTRODUCTION
The brewer incorporates a wireless interface system that allows the DBC Grinder to load certain information into the
"programming tag" located inside the handle of the funnel. This information includes what flavor of coffee is being
ground and what batch size will be brewed (small, medium, or large). Once the correct flavor name and amount of
coffee is ground, the funnel is loaded into the brewer. The information from the funnel handle is then transferred into
the brewer. The brewer then takes this information and dispenses the amount of water preset in the brewer for that
particular flavor of coffee and batch size. The brewer can also be programmed to adjust different functions of the
brewing process, such as brew temperature, brew volumes, bypass percentages, pulse brew, etc. This allows the
operator to program a certain "recipe" for each coffee flavor to be brewed.
Page 2
52187.0 031314
USER NOTICES
The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels.
00986.0000
00658.0000
As directed in the International Plumbing Code of the
International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA),
this equipment must be installed with adequate
backflow prevention to comply with federal, state
and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
00656.0001
37881.0000
MAIN ON/OFF
SWITCH
03408.0004
39803.0000
03409.0004
20201.5600
00824.0002
Page 3
00824.0001
52187.0 090315
CE REQUIREMENTS
• This appliance must be installed in locations where it can be overseen by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance with all local and national codes.
• This appliance must not be cleaned by water jet.
• This appliance can be used by persons aged from 18 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• Keep the appliance and its cord out of reach of children aged less than 18 years.
• Appliances can be used by persons 18 years and above with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children under the age of 18 years should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a
special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.
• Machine must not be immersed for cleaning.
• Cleaning and user maintenance shall not be made by children unless they are older than 18 years and supervised.
• This appliance is intended to be used in household and similar applications such as:
– staff kitchen areas in shops, offices and other working environments;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments.
• This appliance not intended to be used in applications such as:
– farm houses;
• Access to the service areas permitted by Authorized Service personnel only.
• The A-Weighted sound pressure level is below 70 dBA.
NORTH AMERICAN REQUIREMENTS
• This appliance must be installed in locations where it can be overseen by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 41°F to 95°F (5°C to 35°C).
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance with all local and national codes.
• This appliance must not be cleaned by pressure washer.
• This appliance can be used by persons aged from 18 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• Keep the appliance and its cord out of reach of children aged less than 18 years.
• Appliances can be used by persons 18 years and above with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children under the age of 18 years should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a
special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.
• Machine must not be immersed for cleaning.
• Cleaning and user maintenance shall not be made by children unless they are older than 18 years and supervised.
• This appliance is intended for commercial use in applications such as:
– staff kitchen areas in shops, offices and other working environments;
– by clients in hotel and motel lobbies and other similar types of environments;
• Access to the service areas permitted by Authorized Service personnel only.
Page 4
52187.0 022015
ELECTRICAL REQUIREMENTS
WARNING - The brewer must be disconnected from the power source until specified in Initial Set-Up.
Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
WHITE
WHITE
WHITE
NEUTRAL
NEUTRAL
NEUTRAL
L1L1
BLACK
BLACK
L1
BLACK
WHITE
NEUTRAL
GREEN
GREEN
GREEN
L1 BLACK
GREEN
WHITE
WHITE
WHITE
NNN
NEUTRAL
NEUTRAL
NEUTRAL
L1L1
BLACK
BLACK
L1
BLACK
L1
L1
L1
WHITE
N
NEUTRAL
GREEN
GREEN
GREEN
GG
G
L1 BLACK
L1
GREEN
120 volt ac models
G
Note: This electrical service consists of
2 current carrying conductors (L1 and
Neutral) and a separate conductor for
earth ground.
L2L2
L2
RED
RED
RED
L1L1
L1
BLACK
BLACK
BLACK
L2 RED
GREEN
GREEN
GREEN
L1 BLACK
GREEN
L2L2
L2
RED
RED
RED
L1L1
L1
BLACK
BLACK
BLACK
L1
L1
L1
L2 RED
L2
GREEN
GREEN
GREEN
GG
G
L1 BLACK
L1
GREEN
L2L2
L2
RED
RED
RED
L2
L2
L2
G
200 and 208 volt ac models
Note: This electrical service consists
of 2 current carrying conductors (L1
and L2) and a separate conductor for
earth ground.
L1L1
L1
BLACK
BLACK
BLACK
L2 RED
GREEN
GREEN
GREEN
L1 BLACK
GREEN
NNN
NEUTRAL
NEUTRAL
NEUTRAL
BROWN
BROWN
BROWN
L1
L1
L1
BLUE
N
GREEN/
GREEN/
GREEN/
NEUTRAL
YELLOW
YELLOW
YELLOW
GG
G
BROWN
L1
GREEN/
YELLOW
220 - 240 volt ac models
G
Note: This electrical service consists of
2 current carrying conductors (L1 and
Neutral) and a separate conductor for
earth ground.
L2L2
L2
RED
RED
RED
ELECTRICAL HOOK-UP (Models without power cord)
CAUTION – Improper electrical installation will damage electronic components.
Damage caused by incorrect electrical connections is not covered by
warranty.
1. An electrician must provide electrical service as specified in conformance
with all local, state and federal electrical codes.
2. Using a voltmeter, check the voltage and color coding of each conductor at
the electrical source.
3. Remove the front panel beneath the sprayheads to gain access to the terminal
block.
4. Feed the cord through the strain relief and connect it to the terminal block.
5. Connect the brewer to the power source and verify the voltage at the terminal
block before proceeding. Replace the front panel.
6. If plumbing is to be hooked up later be sure the brewer is disconnected from
the power source. If plumbing has been hooked up, the brewer is ready for
Initial Set-Up.
BLUE
BLUE
BLUE
WHITE
WHITE
WHITE
L2NEUTRAL
RED
NEUTRAL
NEUTRAL
L1L1
L1
BLACK
BLACK
BLACK
WHITE
GREEN
GREEN
GREEN
NEUTRAL
L1 BLACK
GREEN
L2L2
L2
RED
RED
RED
L2
L2
L2
WHITE
WHITE
WHITE
NNN
L2
RED
NEUTRAL
NEUTRAL
NEUTRAL
L2
L1L1
L1
BLACK
BLACK
BLACK
L1
L1
L1
WHITE
N
GREEN
GREEN
GREEN
G
G
G
NEUTRAL
L1 BLACK
GREEN
L1
G
120/208 and 120/240 volt ac models
Note: This electrical service consists of
3 current carrying conductors (Neutral,
L1 and L2) and a separate conductor
for earth ground.
ELECTRICAL HOOK-UP (Models with power cord)
WARNING – If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personel with
a special cord available from the manufacturer or its authorized service personel in order to avoid a hazard. Improper
electrical installation will damage electronic components. Damage caused by incorrect electrical connections is not
covered by warranty.
1. An electrician must provide electrical service as specified in conformance with all local, state and federal electrical
codes.
2. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.
NOTE - If the brewer was shipped without a plug on the power cord a qualified service personnel must select and
install the proper UL listed grounding type attachment plug specified on the rear of the brewer.
3. Remove the front panel beneath the sprayheads to gain access to the terminal block.
4. Connect the brewer to the power source and verify the voltage at the terminal block before proceeding.
5. If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has
been hooked up, the brewer is ready for Initial Set-Up.
WARNING – Electrical connections must be made as specified above. Failure to follow these instructions can result in
personal injury, property or equipment damage.
Page 5
52187.0 080817
PLUMBING REQUIREMENTS
This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (.138
and .620 mPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the brewer.
Install a regulator in the line when pressure is greater than 90 psi (.620 mPa) to reduce it to 50 psi (.345 mPa).
The water inlet fitting is 1⁄4" flare or female quick connect.
NOTE – Bunn-O-Matic recommends 1⁄4" copper tubing for installations of less than 25 feet and 3⁄8" for more than 25
feet from the 1⁄2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer
to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The
size and shape of the hole made in the supply line by this type of device may restrict water flow.
As directed in the International Plumbing Code of the International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate
backflow prevention to comply with federal, state and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
PLUMBING HOOK-UP
NOTE - If a backflow preventer is required by code, a shock arrestor should be installed between backflow preventer and dispenser. Installing the shock arrestor as close to dispenser as possible will provide best results.
1. Flush the water line and securely attach it to the fitting located on bottom of brewer.
2. Turn on the water supply.
j
e
OPERATING CONTROLS
f
b
g
f
g
h
j
d
e
c
b
b
/O
ON
IN CH
MA WIT
S
FF
a
h
d
Page 6
c
c
d
h
52187.0 090315
OPERATING CONTROLS - continued
OPERATING CONTROLS
(a) MAIN ON/OFF SWITCH
This switch, located under the brewer behind the right front leg, turns power on and off to all components
in the brewer.
(b) BATCH SELECTOR SWITCHES
Pressing the switch corresponding to the Small, Medium, or Large batch selects the amount of coffee to be
brewed. Pressing a different switch after a brew cycle has been initiated does not change the brew batch in
progress. Light indicates the selected batch to brew.
(c) ON/OFF SWITCH (ENABLE BREW)
Pressing the ON/OFF switch alternately turns the brewing side on and off. Pressing this switch during the brew
cycle will interrupt the brew cycle, stopping the flow of water. Pressing this switch during the programming
of the brewer will exit the setup and return to the main screen.
(d) BREW SWITCH
Momentarily pressing and releasing this switch begins a brew cycle.
(e) PROGRAM SWITCH
Pressing and holding the upper right hidden switch allows entry to the programming menus. Pressing and
releasing the switch steps through each function screen during programming.
(f) FUNCTION SCREEN
This is the display which shows the various functions of the brewer and allows the programming to be accomplished.
(g) FUNCTION SCREEN SWITCHES
These are the hidden switches which are used to program the brewer.
(h) FUNNEL SENSING COILS
These are used to "receive" information from the Smart Funnel handle (coffee name and batch size), and also
from RECIPE CARDS. NOTE: Smart Funnels are an option for Dual Low Profile brewers.
(j) SCROLL BACKWARDS
The upper left hidden switch can be used to scroll backwards through the function list.
Page 7
52187.0 090315
INITIAL SETUP
CAUTION: The brewer must be disconnected from the power source throughout the initial setup, except when
specified in the instructions.
1. Insert an empty funnel into the funnel rails of one of the
brew stations.
2. Place an empty server under the funnel.
3. Connect the brewer to the power source. Main ON/OFF
Switch (located in bottom cover behind right front leg on
some brewers) must be in the ON position. Water will begin
°
°
°
°
flowing into the tank and stop when the tank is filled to its
capacity. Display will show PLEASE WAIT...TANK FILLING
until tank is filled with water.
4. Wait approximately twenty minutes for the water in the tank
to heat to the proper temperature (50 minutes for 120V
models). Display will show READY TO BREW...WATER
TEMP: XXX˚ when tank is at operating temperature.
NOTE: Brew water temperature is factory set at 200° F
(93.3° C). Refer to TEMPERATURE SELECTION below
should the water temperature need to be increased or
decreased. When brew water temperature is changed,
ready temperature should be increased or decreased accordingly.
5. Place a small vessel beneath the faucet and open the faucet
handle. Release it when you hear the tank refilling.
6. Water volumes have been preset at the factory. Refer
to adjustments for the Set Brew Volumes section of the
Programming Manual on the Bunn-O-Matic website, at
www.bunn.com should the volume need to be increased or decreased.
7. The brewer is now ready for use in accordance with the coffee brewing instructions.
TEMPERATURE SELECTION
SET TEMP - Range: 185˚F (85˚C) to 205˚F (96˚C)
This function allows the operator to set the brew water temperature in the tank. It also sets the hot water
faucet dispense temperature.
SET TEMP: XXX°
(-)
DONE
(+)
Procedure to set brew temperature:
1. Press and hold upper right hidden switch until the display reads SELECT RECIPE. Release switch. Continue
to press and release switch until the display reads SET TEMP.
2. To adjust the brew temperature, press (-) to decrease or (+) to increase the brew temperature.
3. When finished, press and release DONE to save the new setting, exit the SET TEMP function and advance to
the next function screen, SET READY. Another alternative is to press and release the ON/OFF switch (either
on DUAL brewers) located on the front switch panel to exit the SET TEMP function and return to the MAIN
SCREEN.
Page 8
52187.0 090315
TEMPERATURE SELECTION (cont)
SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C)
This function allows the operator to set the minimum temperature allowable to start a brew cycle. The range
can be from 185˚F (85˚C) to within 2˚F (-1.7°C) of the SET TEMP. The water must be at the SET READY temperature or higher for the display to indicate READY TO BREW. If brew lockout is enabled, the brewing process will
not start below this READY temperature.
NOTE: The upper limit for SET READY temperature is 2˚F (-1.7°C) less than the water temperature (SET TEMP)
setting.
SET READY: XXX°
(-)
DONE
(+)
Procedure to set ready temperature:
1. Press and hold upper right hidden switch until the display reads SELECT RECIPE. Release switch. Continue
to press and release switch until the display reads SET READY.
2. To adjust the ready temperature, press the (-) button to decrease, or (+) to increase the ready temperature.
3. When finished, press and release DONE to save the new setting, exit the SET READY function and advance
to the next function screen, REFILL. Another alternative is to press and release the ON/OFF switch (either
on DUAL brewers) located on the front switch panel to exit the SET READY function and return to the MAIN
SCREEN.
COFFEE BREWING
1. Insert a BUNN filter into the Funnel .
2. If a grinder is not used to obtain the coffee grounds, pour the proper amount of fresh coffee grounds into
the funnel and level by gently shaking. Slide the funnel into the funnel rails and select batch size. Proceed to
step 5.
3. If a G9-2T DBC or MHG grinder is used with a compatible Smart Funnel, select the desired batch size on the
grinder. Grind the selected amount of fresh coffee into funnel and level grounds by gently shaking. It is not
necessary to select a size on the brewer.
4. Slide the funnel into the funnel rails. The brewer will read the size ground through the chip in the funnel
handle and will automatically select the correct size to brew.
5. Place an empty server under the funnel.
6. The ENABLE BREW switch must be ON. Momentarily press and release the "BREW" switch. If the brewer has
the funnel lock option and if it is activated, once a brew cycle has been started the funnel is locked in place.
There may be certain situations in which the brew cycle will not begin when the brew switch is pressed:
a)
b)
c)
d)
BREW TEMPERATURE TOO LOW - wait until heated or cancel BREW LOCKOUT option.
FUNNEL NOT IN PLACE (or using a standard brew funnel) - cancel FUNNEL DETECT option.
CHECK FUNNEL - remove funnel, empty previously brewed grounds and grind a new batch into funnel.
SERVER NOT IN PLACE - place Soft Heat Server, or cancel SERVER DETECT option.
7. If none of the above messages are displayed, the display will read NOW BREWING and the time remaining
in the brew cycle. Arrows will point to the side which is brewing. If both sides are brewing simultaneously,
the arrows will alternate from left to right on the display.
8. Following the BREW will be a countdown of DRIPPING time which shows the time remaining until the funnel
lock will release. Discard the grounds and filter only after visible dripping stops.
52187.0 090315
Page 9
CLEANING
1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment.
2. Check and clean the sprayhead. Use the pointed end of sprayhead cleaning tool (#38227.0000) to remove
any mineral deposits from the sprayhead holes.
3. Insert the long end of sprayhead cleaning tool into the sprayhead fitting, and rotate several times to remove
any mineral deposits from the fitting.
4. Insert the short end of sprayhead cleaning tool into the bypass fitting, and rotate several times to remove
any mineral deposits from the fitting.
NOTE: In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer
and takes less than a minute.
Page 10
52187.0 090315
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising