Bunn | Single® SH Soft Heat® DBC® Stainless 120/240V | Service manual | BUNN Single® SH Soft Heat® DBC® Stainless, 120V Single BrewWISE® Soft Heat® DBC® 120V w/Fnl Lks & Lwr Faucet Service Manual

BUNN Single® SH Soft Heat® DBC® Stainless, 120V Single BrewWISE® Soft Heat® DBC® 120V w/Fnl Lks & Lwr Faucet Service Manual
USE & CARE INSTRUCTIONS for BrewWISESM System
(Includes G92T DBC Grinder and DUAL SH DBC Brewer with Smart Funnel™)
COFFEE BREWING
STEP 1
STEP 2
Insert a BUNN filter into Select the desired batch
size and coffee flavor on
the funnel.
the grinder. It is not necessary to select a size on
the brewer.
®
STEP 3
STEP 4
STEP 5
Grind the proper amount of Level grounds by gently Slide funnel into the funfresh coffee into the Smart shaking.
nel rails. The brewer reads
Funnel™ using the G92the batch size and flavor
HD with Smart Funnel™
ground through a chip in
operation.
the funnel handle and will
automatically select the
correct settings to brew.
STEP 6
STEP 7
STEP 9
STEP 10
STEP 8
Place an empty server Press the ON/OFF button A batch size must be cho- Momentarily press and Discard the grounds and
under the funnel.
to ON.
sen at the brewer when release the BREW button. filter when brewing is
grounds are not obtained
completed.
from a Smart Funnel™
compatible grinder.
CLEANING
STEP 1
Remove the sprayhead.
34481.0000C
STEP 2
STEP 3
Clean mineral deposits Reinstall the sprayhead.
and rinse. Using a paper
clip, make sure all holes
are open.
03/17 ©2003 Bunn-O-Matic Corporation
STEP 4
STEP 5
Use a clean damp cloth Remove the lid of the
rinsed in nonabrasive, server.
mild detergent to clean all
surfaces.
34481 011403
USE & CARE INSTRUCTIONS for BrewWISESM System
(Includes G92T DBC Grinder and DUAL SH DBC Brewer with Smart Funnel™)
CLEANING (Continued)
STEP 6
Pull out lid assembly.
STEP 11
Remove the glass tube.
STEP 7
Unscrew the inlet cap.
STEP 12
STEP 8
STEP 9
STEP 10
Clean inlet tube with the Rinse well. Reassemble Make sure reservoir is
medium sized brush the lid making sure to empty and unscrew the
(BOM #00675.0000) and replace the retainer cap. sight gauge cap.
cleaning product solution.
STEP 13
STEP 14
Clean the sight gauge with Reinstall glass tube and Thoroughly rinse entire
inside of the server. DO
the small brush (BOM the sight gauge cap.
NOT immerse server in
#00674.0000) and reaswater.
semble.
STEP 15
Use a clean damp cloth
rinsed in nonabrasive,
mild detergent to clean all
surfaces.
STEP 16
STEP 17
STEP 18
STEP 19
STEP 20
Turn the faucet wing nut in
a clockwise direction and
remove the faucet from
the dispenser. Unscrew
the faucet cap from the
faucet body and disassemble all faucet parts.
Transfer these parts to a
three compartment sink
for cleaning. Fill the first
sink with a soap solution
using a mild detergent,
the second sink is used for
clean rinse and the third
sink is used for a sanitizer
solution (75°F warm
non-chlorine sanitizing
solution).
Use a small brush (BOM
#00674.0000) to thoroughly scrub the faucet
body.
Use a small brush (BOM
#00674.0000) to thoroughly scrub the faucet
shank.
Allow the parts to soak in
a sanitizer solution for a
minimum of ten minutes.
Remove the faucet parts
from the sanitizer solution.
Allow parts to air-dry
overnight.
34481 031617
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising